Download Steam Iron Elance GC3320 - Recambios, accesorios y repuestos
Transcript
Steam Iron Elance GC3320 Philips Domestic Appliances and Personal Care Service Manual PRODUCT INFORMATION TECHNICAL INFORMATION Features - Extra large water inlet for fast filling - Extra long cord length (3 m) for easy reach - Extra clear indicator for high visibility of water level - Careeza soleplate - Tank capacity 300 ml - Spray feature - Steam rate 35 g/min - Shot Of Steam & Vertical steam 90 g/min - Integrated calc clean - 360° ball swivel - Integrated cord winder Voltage Frequency Power Dimension (Iron) Weight (Iron) Safety Information - This product meets the requirements regarding interference suppression on radio and TV. - After the product has been repaired, it should function properly and has to meet the safety requirements and legal regulations as officially laid down at this moment. More Control With the extra clear indicator, water level is highly visible and you know if you have enough water for that last garment. : : : : : 120 V, 230 V 50 - 60 Hz 1300 W, 2200 W 303 x 120 x 152 mm (L x W x H) 1.34 kg Fast Filling With the extra large water inlet, adding water to the iron is quick, easy & spill-free. Easy Reach With the extra long cord length of 3m, you can easily reach right up to the edge of your ironing board. Careeza Soleplate This is a multi-layer ceramic that glides smoothly over all types of fabric, keeping your clothes in perfect condition. Vertical Steam This offers the Shot Of Steam in vertical position to remove wrinkles on hanging garment. Published by Philips Domestic Appliances and Personal Care 06/12 Printed in the Netherlands © Copyright reserved Subject to modification GC3320 DISASSEMBLY ADVICE THERMOSTAT DIAL 1 BACKPLATE 2 CORDSET 3 BALL SWIVEL 4 Remove Remove Remove Remove Screw A (1x) BACKPLATE 2 Screw B (2x) Cord clamp CLAMP BRACKET 14 HEAT SHIELD 24 DOSING CAM 15 COVER 25 STEAM SHAFT ASSY 16 SOS SEAL 26 SHAFT BELLOW 17 DOSING SEAL 27 Remove Remove Remove Remove Remove Remove Remove Remove Remove Remove Screw A (1x) BACKPLATE 2 FILLING DOOR ASSY 7 Screw C (1x) SUB-INLAY 6 INLAY 5 SOS KNOB 11 SPRAY KNOB 12 Screw D (2x) CLAMP BRACKET 14 HOUSING PRINTED 18 PLASTIC RATTLE SPRING 19 INLAY 5 PUMP ASSY 20 SUB-INLAY PRINTED 6 WATER TANK ASSY 21 FILLING DOOR ASSY 7 ORIFICE 22 STEAM SLIDER 8 THERMOSTAT BUSH 23 LAMP ASSY 9 SOS KNOB 11 SPRAY KNOB 12 TANK TOP SEAL 13 Remove Remove Remove Remove Remove Remove Screw A (1x) BACKPLATE 2 FILLING DOOR ASSY 7 Screw C (1x) SUB-INLAY 6 INLAY 5 Remove Remove Remove Remove Remove Remove Remove Remove Remove Remove Remove Remove Remove SOLEPLATE ASSY 28 Remove Remove Remove Remove Remove Remove Remove Remove Remove Remove Remove Remove Remove Remove Screw A (1x) BACKPLATE 2 Screw B (2x) Cord clamp FILLING DOOR ASSY 7 Screw C (1x) SUB-INLAY 6 INLAY 5 Screw E (2x) Screw F (2x) WATER TANK ASSY 21 Screw G (3x) HEAT SHIELD 24 COVER 25 Screw A (1x) BACKPLATE 2 Screw B (2x) Cord clamp FILLING DOOR ASSY 7 Screw C (1x) SUB-INLAY 6 INLAY 5 Screw E (2x) THERMOSTAT DIAL 1 HOUSING PRINTED 18 Screw F (2x) WATER TANK ASSY 21 2-5 REPAIR INSTRUCTIONS GC3320 - Due to the high wattage of the iron, only the specified cord set must be used. - Should damage be observed on the CORDSET 3, it must be replaced. Continued usage is not allowed. - For standardization reason, the COVER 25 is provided without type plate information eg. type number, voltage etc. When replacing the cover, engrave the type number & voltage on the type plate with a sharp object. - After the product has been repaired, it should function properly and has to meet the safety requirements & legal regulations as laid down & officially established at this moment. - The following tests are common checks that are conducted on a repaired product before it is returned to the consumer. 1. Soleplate temperature Check that soleplate temperature is within IEC requirement. Measure the temperature of the soleplate after the iron has reached steady state i.e connected to the mains for at least 15 minutes. The table below shows the temperature requirement. Material, for example Minimum Maximum Nominal + Tolerance (1 dot) 70 120 95 ± 25 •• (2 dots) 100 160 130 ± 30 Cupro, polyester, silk, triacetate, viscose, wool ••• (3 dots) 140 210 175 ± 35 Cotton, linen Testpoint Acetate, elastane, polyamide, polyproylene = • = Soleplate temperature (Deg C) Marking 2. Leakage current Check that leakage current is within IEC requirement. Measure leakage current between LIVE/NEUTRAL & EARTH. IEC requirement is that at 230 V supply, the EARTH leakage current must be less than 0.75 mA. 3. Water leakage / Functionality Check that there is no water leakage from any part of the product during operation. Check that the functionality of the product (product dependent) eg. steaming, variable steam, SOS, ASO etc is working properly. 4. Loose part Check that there are no loose parts eg. extra screw in the product that can cause short-circuit or product malfunction. 3-5 PARTS LIST GC3320 Pos Service code 1 4239 021 41560 4239 021 40500 4239 021 41500 4239 021 41700 4239 021 41710 Thermostat dial printed Thermostat dial printed Thermostat dial printed Thermostat dial printed Thermostat dial printed 2 3 4 5 4239 026 27080 4239 000 07760 4239 000 09650 4239 026 27130 4239 026 26810 Backplate Cordset EU Cordset Taiwan Ball swivel Inlay 6 7 8 9 10 4239 021 40670 4239 021 40950 4239 026 27020 4239 021 32500 4239 026 01220 Sub-inlay printed Filling door assy Steam slider Lamp assy Lamp holder 11 12 13 14 15 4239 026 26830 4239 026 26840 4239 015 55800 4239 026 19450 4239 026 19440 SOS knob Spray knob Tank top seal Clamp bracket Dosing cam 16 4239 021 33170 4239 021 35680 4239 015 53170 4239 026 27030 4239 026 27200 Steam shaft assy 230 V Steam shaft assy 120 V Shaft bellow Housing printed Plastic rattle spring 22 4239 020 90560 4239 021 40760 4239 021 41760 4239 021 41480 4239 025 99230 Pump assy Water tank assy (Non anti-calc) Water tank assy (Non anti-calc) Korea Water tank assy (Non anti-calc) Taiwan Orifice 23 24 25 26 27 4239 026 13220 4239 010 09170 4239 026 19430 4239 015 54410 4239 015 55920 Thermostat bush Heat shield Cover (Non Drip stop) SOS seal Dosing seal 28 4239 021 41380 4239 021 39850 Soleplate assy 120 V / 1300 W Soleplate assy 230 V / 2200 W 4239 026 10270 Filling cup 17 18 19 20 21 Description (Spa/Ita/Por text) (Ger/Swe text) (Eng text) (Fre/Dut text) (Eng/Kor text) N RESISTOR INPUT LAMP HEATING UNIT FUSE L THERMOSTAT E 4-5 EXPLODED VIEW GC3320 8 C 1 7 9 6 4 A 5 3 F1 11 2 E1 12 F2 10 E2 13 18 D1 19 D2 14 15 B1 B2 Clamping plate 20 22 21 23 16 G1 17 G2 G3 24 25 27 26 28 5-5