Download Table of Contents - Frank`s Hospital Workshop

MRT10*RDA001A/E
Table of Contents
Page
INTRODUCTION ........................................................................................................ 1-1
§1
§2 SAFETY PRECAUTIONS ............................................................................................ 2-1
§3 TROUBLE SHOOTING ............................................................................................... 3-1
§4 SUB TOUBLE SHOOTING ......................................................................................... 4-1
4.1 Initialization screen does not appear on the CB display. ............................................... 4-1
4.1.1 Backlight of the LCD module does not light up. .................................................. 4-2
4.2 Initialization is not completed properly. ........................................................................ 4-3
4.2.1 The battery AS does not move to the right and left. ............................................ 4-4
4.2.2 The R disk AS does not turn. ............................................................................. 4-5
4.2.3 The L disk AS does not turn. ............................................................................. 4-7
4.2.4 The PD and convergence of the MB is not initialized properly. ............................ 4-9
4.2.5 The right disk of the MB is not initialized properly. ............................................ 4-10
4.2.6 The left disk of the MB is not initialized properly. .............................................. 4-11
4.3 An error message appears. ....................................................................................... 4-12
4.3.1 “Error 01: Communication Error CB-MB” appears. ......................................... 4-13
4.3.2 “Error 11: Communication Error CB-RB” appears. .......................................... 4-14
4.3.3 “No appointment data!!” appears. ................................................................... 4-14
4.3.4 “Chart doesn’t work.” appears. ....................................................................... 4-15
4.3.5 “Setup data is initialized.” appears. ................................................................... 4-16
4.3.6 “CF card -- Read Error!!” appears. ................................................................ 4-16
4.3.7 “CF card -- Write Error!!” appears. ................................................................ 4-16
4.3.8 “CF card -- File Error!!” appears. ................................................................... 4-16
4.3.9 “CF card -- File not found!!” appears. ............................................................. 4-16
4.3.10 “CF card -- Card not found!!” appears. ........................................................ 4-16
4.3.11 “No data!!” appears. ..................................................................................... 4-16
4.4 The instrument cannot be operated with the control box. ............................................ 4-17
4.4.1 The instrument cannot be operated with the switches. ....................................... 4-17
4.4.2 The instrument cannot be operated by turning the dial. ...................................... 4-18
4.4.3 The instrument cannot be operated with the touch-screen panel. ....................... 4-18
4.5 The compact flash memory card cannot be used. ....................................................... 4-19
4.6 The IC card cannot be used. ..................................................................................... 4-19
4.7 The printer does not print. ......................................................................................... 4-20
4.8 The communication with the auto refractometers or lensmeter cannot be done. ........... 4-21
4.9 The chart projector does not work as specified with the control box. ......................... 4-22
MRT10*RDA001A/E
Page
§5 REMOVING COVERS ................................................................................................ 5-1
5.1 Covers of the main body ............................................................................................. 5-1
5.1.1 Face shields R and L ......................................................................................... 5-1
5.1.2 Rear covers ...................................................................................................... 5-1
5.1.2.1 Rear cover R ........................................................................................ 5-1
5.1.2.2 Rear cover L ......................................................................................... 5-1
5.1.3 Front covers ..................................................................................................... 5-2
5.1.3.1 Front cover R ....................................................................................... 5-2
5.1.3.2 Front cover L ........................................................................................ 5-2
5.1.4 Knob S AS ....................................................................................................... 5-2
5.1.5 Upper cover J ................................................................................................... 5-3
5.1.6 Upper rear cover .............................................................................................. 5-3
5.1.7 Upper cover F .................................................................................................. 5-3
5.2 Control box covers ..................................................................................................... 5-4
5.2.1 Rear cover AS .................................................................................................. 5-4
5.2.2 EMC cover ....................................................................................................... 5-4
§6 REPLACEMENT.......................................................................................................... 6-1
6.1 Battery AS ................................................................................................................. 6-1
6.2 Disk AS ..................................................................................................................... 6-2
6.2.1 R disk AS (
) ................................................................................................. 6-2
6.2.2 L disk AS ( ) .................................................................................................. 6-2
6.3 Boards R and L .......................................................................................................... 6-2
6.3.1 Board R ............................................................................................................ 6-2
6.3.2 Board L ............................................................................................................ 6-3
6.4 Plates ......................................................................................................................... 6-3
6.4.1 Plate FR (
) .................................................................................................... 6-3
6.4.2 Plate FL (
) .................................................................................................... 6-3
6.4.3 Plate BR (
) ................................................................................................... 6-4
6.4.4 Plate BL ( ) .................................................................................................... 6-4
6.5 Sensor 1 .................................................................................................................... 6-4
6.5.1 Sensor 1R ......................................................................................................... 6-4
6.5.2 Sensor 1L ......................................................................................................... 6-5
6.6 Frames ....................................................................................................................... 6-5
6.6.1 Frame R (
) .................................................................................................... 6-5
6.6.2 Frame L ( ) .................................................................................................... 6-5
6.7 PD motors ................................................................................................................. 6-5
6.7.1 PD motor R ...................................................................................................... 6-5
6.7.2 PD motor L ...................................................................................................... 6-6
6.8 CON motors .............................................................................................................. 6-6
6.8.1 CON motor R .................................................................................................. 6-6
6.8.2 CON motor L ................................................................................................... 6-6
6.9 PI sensor boards ........................................................................................................ 6-7
6.9.1 CON sensor ..................................................................................................... 6-7
MRT10*RDA001A/E
Page
6.9.1.1 CON sensor of the upper brace R ......................................................... 6-7
6.9.1.2 CON sensor of the upper brace L ......................................................... 6-7
6.9.2 PD sensors ....................................................................................................... 6-8
6.9.2.1 PD sensor of the upper brace R ............................................................. 6-8
6.9.2.2 PD sensor of the upper brace L ............................................................. 6-8
6.10 Motors and sensors of frame R ................................................................................. 6-9
6.10.1 Motor SCA .................................................................................................... 6-9
6.10.1.1 Motor for the S2 disk .......................................................................... 6-9
6.10.1.2 Motor for the C2 disk ......................................................................... 6-9
6.10.1.3 Motor for the S1 disk ........................................................................ 6-10
6.10.1.4 Motor for the A1 disk (
) ................................................................ 6-10
6.10.1.5 Motor for the C1 disk (
) ............................................................... 6-11
6.10.1.6 Motor for the A2 disk ( ) ................................................................ 6-11
6.10.2 Motor PCA .................................................................................................. 6-12
6.10.2.1 Motor for the CA disk (
) ............................................................... 6-12
6.10.2.2 Motor for the P1 disk (
) ................................................................ 6-12
6.10.2.3 Motor for the P2 disk ( ) ................................................................ 6-12
6.10.3 Sensor 2 ....................................................................................................... 6-13
6.10.3.1 Sensor for the CA disk ...................................................................... 6-13
6.10.3.2 Sensor for the P1 disk ....................................................................... 6-13
6.10.3.3 Sensor for the P2 disk ....................................................................... 6-13
6.11 Motors or sensors of frame L.................................................................................. 6-14
6.11.1 Motor SCA .................................................................................................. 6-14
6.11.1.1 Motor for the S2 disk ........................................................................ 6-14
6.11.1.2 Motor for the C2 disk ....................................................................... 6-14
6.11.1.3 Motor for the S1 disk ........................................................................ 6-15
6.11.1.4 Motor for the A1 disk (
) ................................................................ 6-15
6.11.1.5 Motor for the C1 disk (
) ................................................................ 6-16
6.11.1.6 Motor for the A2 disk ( ) ................................................................ 6-16
6.11.2 Motor for the CA disk ................................................................................... 6-17
6.11.2.1 Motor for the CA disk (
) ............................................................... 6-17
6.11.2.2 Motor for the P1 disk (
) ................................................................ 6-17
6.11.2.3 Motor for the P2 disk ( ) ................................................................ 6-17
6.11.3 Sensor 2 ....................................................................................................... 6-18
6.11.3.1 Motor for the CA disk (
) ............................................................... 6-18
6.11.3.2 Motor for the P1 disk (
) ................................................................ 6-18
6.11.3.3 Motor for the P2 disk ( ) ................................................................ 6-18
6.12 VD LED unit .......................................................................................................... 6-19
6.12.1 VD LED unit of frame R ................................................................................ 6-19
6.12.2 VD LED unit of frame L ................................................................................ 6-19
6.13 L motor CPU board ............................................................................................... 6-20
6.14 L motor driver board .............................................................................................. 6-20
6.15 R motor CPU board ............................................................................................... 6-20
MRT10*RDA001A/E
6.16 R motor driver board .............................................................................................. 6-20
6.17 MB main board ...................................................................................................... 6-21
6.18 LCD AS ................................................................................................................ 6-21
6.19 CB main board ....................................................................................................... 6-22
6.20 Key I/F board ........................................................................................................ 6-22
6.21 Link board ............................................................................................................. 6-23
6.22 Rotary encoder ...................................................................................................... 6-23
6.23 LCD I/F board ....................................................................................................... 6-24
6.24 Inverter .................................................................................................................. 6-24
6.25 Color LCD module ................................................................................................ 6-25
6.26 RB main board ....................................................................................................... 6-26
6.27 RB I/F board ......................................................................................................... 6-26
§7 ADJUSTMENT ............................................................................................................. 7-1
7.1 Entering the Information/Adjustment screen ................................................................. 7-1
7.2 Adjustment mode of the MB ....................................................................................... 7-1
7.2.1 Adjustment of the initial pulse for the MB ........................................................... 7-1
7.2.2 Lens cleaning mode ........................................................................................... 7-2
7.2.3 Adjustment mode for gear ................................................................................. 7-2
7.3 Chart selection ........................................................................................................... 7-3
7.4 Chart adjustment ........................................................................................................ 7-3
7.5 Mirror adjustment ....................................................................................................... 7-3
7.6 Parameter setting ....................................................................................................... 7-4
7.7 Printing the adjustment value ....................................................................................... 7-4
7.8 Resetting the setup data .............................................................................................. 7-4
7.9 Communication setting with other brand AR/LM ......................................................... 7-5
7.10 Adjusting the clock ................................................................................................... 7-5
7.11 Updating the software ............................................................................................... 7-6
7.12 Clearing the AR/LM data .......................................................................................... 7-6
7.13 Touch-screen panel calibration .................................................................................. 7-7
§8 REFERENCE ................................................................................................................ 8-1
8.1 Wiring diagram ........................................................................................................... 8-1
8.2 Connector cables ....................................................................................................... 8-2
8.3 Error messages ........................................................................................................... 8-5
8.4 Parameters ................................................................................................................. 8-6
MRT10*RDA001A/E
§1 INTRODUCTION
• This service manual provides information for after-sales service for the NIDEK refractor, model:
RT-5100.
• Refer to the RT-5100 Operator’s Manual and Parts List.
• Specifications are subject to change without notice for improvement. Refer to the Technical
Bulletins (T.B.) for important changes.
• In case the device cannot be repaired according to the procedures described in this manual,
please report the serial number and details of the symptom or symptoms.
1-1
MRT10*RDA001A/E
1-2
MRT10*RDA001A/E
§2 SAFETY PRECAUTIONS
<General precautions>
• Only the service persons who are accustomed to using tools, and have a deep knowledge of
this instrument are allowed to repair the instrument.
• Proceed right work in accordance with the procedure.
If not, accidents or failure of the instrument may result.
• When performing maintenance works, turn off the power switch, and disconnect the power
cord from the wall outlet unless necessary.
• Never wipe the covers, etc. using an organic solvent such as a paint thinner.
The surface may be ruined, and as a result, the appearance of the instrument will be impaired.
<Maintenance precautions>
•
•
•
•
•
In case of instrument malfunction, turn the power switch off after checking the symptom.
Never drop parts or screws inside the instrument, nor bump it against the surrounding objects.
Have storage cases ready to ensure the loss of the removed screws or parts.
In screwing or unscrewing, use a proper tool for the screw
After loosening the screws fixed by a thread-locking adhesive, and tightening them again, be
sure to apply the thread-locking adhesive to them.
• After replacing parts, make sure that they are fixed securely before turning on the power.
• If you observe strange odors or smoke being emitted from the instrument, immediately turn
off the instrument and locate the causes after disconnecting the power cord from the walloutlet.
If the instrument is continuously powered under such abnormal conditions, a fire, electric
shock or total loss of the instrument may result.
• Referring to “8.1 Wiring diagram” and “8.2 Connector cables”, check cables for the following:
1. Connectors are connected securely.
2. No contact failure occurs after re-connection of connectors.
3. No failure in soldering
Do not pull the cables strongly. It may cause a breaking of wire.
Never work with wet hands. It may result in an electric shock or instrument malfunction.
<Adjustment precautions>
• Perform adjustment work in a vibration-free, flat and stable place.
Tilted floor or vibratory place may affect a proper adjustment adversely.
• Do not use an adjustment jig for other usage described in this manual.
• Be sure to readjust the optical axis of the prism and cylinder after performing the marked ( )
procedures. The special jigs (the chart projector and the test scale for checking) are necessary
for the readjustment.
2-1
MRT10*RDA001A/E
2-2
MRT10*RDA001A/E
§3 TROUBLESHOOTING
Turn ON the main switch.
Does the starting screen appear on the control box?
No
4.1 The starting screen does not appear on the control
box.
Yes
Is the initialization completed properly?
No
4.2 Initialization is not completed properly.
Yes
Does any error message appear?
Yes
4.3 An error message appears.
No
Can the instrument operated with the control box?
No
4.4 The instrument cannot be operated with the control
box.
Yes
Can the compact flash memory card be used?
No
4.5 The compact flash memory card cannot be used.
Yes
Can the IC card be used?
No
4.6 The IC card cannot be used.
Yes
Does the printer print?
No
4.7 The printer does not print.
Yes
Can the communication between the autorefractometer No
and lensmeter be done?
4.8 The communication between the autorefractometer
and lensmeter cannot be done.
Yes
Does the chart projector operate as specified with the No
control box?
Yes
Turn OFF the main switch.
3-1
4.9 The chart projector does not operate as specified
with the control box.
MRT10*RDA001A/E
3-2
MRT10*RDA001A/E
§4 SUB TROUBLESHOOTING
4.1 Initialization screen does not appear on the CB display.
Is the power supply voltage within the specified range?
No
Obtain the specified voltage.
Yes
Does the fuse of the RB blow?
Yes
Replace the fuse of the RB.
No
Is the voltage setting of the RB correct?
No
Set the correct voltage of the RB.
Yes
Is the voltage between 1-2 pins of connector P8 on the No
RB I/F board (34085-BA22) AC24±3V?
Replace the RB (34085-5000).
Yes
Is the voltage between A1-B3 pins of connector J3 on No
the RB I/F board (34085-BA22) DC+15V?
Replace the RB I/F board (34085-BA22). (See 6.27.)
Yes
Does cable CB break?
Yes
Replace cable CB.
No
Is the voltage between A1-A6 pins of connector P14 on No
the LINK board (34085-BA14) DC+15V?
Replace the LINK board (34085-BA14). (See 6.21.)
Yes
Does the backlight of the color LCD module light up?
No
4.1.1 Backlight of the color LCD module does not light
up.
Yes
Is the voltage between 1-3 pins of connector J3 on the No
CB main board (34085-BA11) DC+3.3V?
Replace the CB main board (34085-BA11). (See 6.19.)
Yes
Is cable LCD3 (34085-E305) disconnected from the Yes
connector?
No
4-1
Reconnect cable LCD3 (34085-E305).
MRT10*RDA001A/E
Is the voltage between 1-3 pins of connector J33 on the No
LCD I/F board (34085-BA13) DC+3.3V?
Replace the LCD I/F board (34085-BA13). (See 6.23.)
Yes
Replace the color LCD module (42203-E016).
(See 6.25.)
Is the symptom relieved?
No
Replace the CB main board (34085-BA11). (See 6.19.)
Yes
Completion
4.1.1 Backlight of the LCD module does not light up.
Is the voltage between 5-7 pins of connector J12 on the No
CB main board (34085-BA11) DC+15V?
Replace the CB main board (34085-BA11). (See 6.19.)
Yes
Does cable LCD2 (34085-E304) break?
Yes
Replace cable LCD2 (34085-E304).
No
Is the voltage between 1-2 pins of connector J35 on the No
LCD I/F board (34085-BA13) DC+12V?
Replace the LCD I/F board (34085-BA13). (See 6.23.)
Yes
Is cable BL (34085-EA11) disconnected from the Yes
connector?
Reconnect cable BL (34085-EA11).
No
Replace the inverter (42203-E17). (See 6.24.)
Is the symptom relieved?
No
Yes
Completion
4-2
Replace the CB main board (34085-BA11). (See 6.19.)
MRT10*RDA001A/E
4.2 Initialization is not completed properly.
Is the voltage between A1-A4 pins of connector J1 on
No
the MB main board (34085-BA01) DC+5V, and the
voltage between A12-A8 pins DC+16.5V?
Check the wiring of cable MB and replace it.
Yes
Does the battery AS (34085-1000) move to the right No
and left?
4.2.1 The battery AS (34085-1000) does not move to
the right and left.
Yes
Does the R disk AS (34085-1100) turn?
No
4.2.2 The R disk AS (34085-1100) does not turn.
Yes
Does the L disk AS (34085-1200) turn?
No
4.2.3 The L disk AS (34085-1200) does not turn.
Yes
Is the PD of the MB and the convergence initialized No
properly?
4.2.4 The PD of the MB and convergence is not
initialized properly.
Yes
Is the right disk of the MB initialized properly?
No
4.2.5 The right disk of the MB is not initialized
properly.
Yes
Is the left disk of the MB initialized properly?
No
Yes
Completion
4-3
4.2.6 The left disk of the MB is not initialized properly.
MRT10*RDA001A/E
4.2.1 The battery AS does not move to the right and left.
Does motor CON (34085-E013) of the PD motor R Yes
(34085-2510) break?
Replace the PD motor R (34085-2510). (See 6.7.1.)
No
Does motor CON (34085-E013) of the CON motor R Yes
(34085-2520) break?
Replace the CON motor R (34085-2520). (See 6.8.1.)
No
Does motor CON (34085-E013) of the PD motor L Yes
(34085-2610) break?
Replace the PD motor L (34085-2610). (See 6.7.2.)
No
Does motor CON (34085-E013) of the CON motor L Yes
(34085-2620) break?
Replace the CON motor L (34085-2620). (See 6.8.2.)
No
Is the voltage as described below when disconnecting
each connector on the MB main board (34085-BA01)?
No
1-2 pins of connector J8
: DC+5V
1-2 pins of connector J9
: DC+5V
1-2 pins of connector J10
: DC+5V
1-2 pins of connector J11
: DC+5V
Replace the MB main board (34085-BA01). (See 6.17.)
Yes
Does the PI sensor board (34085-BA08) for PD of the Yes
upper brace R (34085-2500) break?
Replace the PI sensor board (34085-BA08) for PD of
the upper brace R (34085-2500). (See 6.9.2.1.)
No
Does the PI sensor board (34085-BA08) for CON of Yes
the upper brace R (34085-2500) break?
Replace the PI sensor board (34085-BA08) for CON of
the upper brace R (34085-2500). (See 6.9.1.1.)
No
Does the PI sensor board (34085-BA08) for PD of the Yes
upper brace L (34085-2600) break?
Replace the PI sensor board (34085-BA08) for PD of
the upper brace L (34085-2600). (See 6.9.2.2.)
No
Does the PI sensor board (34085-BA08) for CON of Yes
the upper brace L (34085-2600) break?
No
Replace the MB main board (34085-BA01). (See 6.17.)
4-4
Replace the PI sensor board (34085-BA08) for CON of
the upper brace L (34085-2600). (See 6.9.1.2.)
MRT10*RDA001A/E
4.2.2 The R disk AS does not turn.
Is the voltage of connector J3 on the R motor CPU
board (34085-BA04) as described below?
No
A3-A1 pins
:DC+5V
A4-A1 pins
:DC+16.5V
Replace the MB main board (34085-BA01). (See 6.17.)
Yes
Is the voltage of connector P1 on the R motor CPU
board (34085-BA04) as described below?
No
1-3 pins :DC+5V
11-1 pins :DC+16.5V
Replace the R motor CPU board (34085-BA04).
(See 6.15.)
Yes
Is the voltage as described below when disconnecting
each connector of the R motor CPU board (34085BA04)?
No
1-2 pins of connector J4
: DC+5V
1-2 pins of connector J5
: DC+5V
1-2 pins of connector J6
: DC+5V
1-2 pins of connector J7
: DC+5V
Replace the R motor CPU board (34085-BA04).
(See 6.15.)
Yes
Does motor SCA (34085-1310) for S2 disk R break?
Yes
Replace motor SCA (34085-1310) for the S2 disk R.
(See 6.10.1.)
Yes
Replace motor SCA (34085-1310) for the S1 disk R.
(See 6.10.3.)
Yes
Replace motor SCA (34085-1310) for the C2 disk R.
(See 6.10.1.2.)
Yes
Replace motor SCA (34085-1310) for the C1 disk R.
(See 6.10.1.5.)
Yes
Replace motor SCA (34085-1310) for the A1 disk R.
(See 6.10.1.4.)
Yes
Replace motor SCA (34085-1310) for the A2 disk R.
(See 6.10.16.)
No
Does motor SCA (34085-1310) for S1 disk R break?
No
Does motor SCA (34085-1310) for C2 disk R break?
No
Does motor SCA (34085-1310) for C1 disk R break?
No
Does motor SCA (34085-1310) for A1 disk R break?
No
Does motor SCA (34085-1310) for A2 disk R break?
No
4-5
MRT10*RDA001A/E
Does motor PCA (34085-1320) for the CA disk R Yes
break?
Replace motor PCA (34085-1320) for the CA disk R.
(See 6.10.2.1.)
No
Does motor PCA (34085-1320) for the P1 disk R Yes
break?
Replace motor PCA (34085-1320) for the P1 disk R.
(See 6.10.2.2.)
No
Does motor PCA (34085-1320) for the P2 disk R Yes
break?
Replace motor PCA (34085-1320) for the P2 disk R.
(See 6.10.2.3.)
No
Is the voltage between 3-2 pins of connector J4 on the
R motor CPU board (34085-BA04) as described
No
below?
Sensor 2 for CA disk R is shaded.
:5V
Sensor 2 for CA disk R is not shaded.
:0V
Replace sensor 2 (34085-1330) for the CA disk R.
(See 6.10.3.1.)
Yes
Is the voltage between 3-2 pins of connector J5 on the
R motor CPU board (34085-BA04) as described
No
below?
Sensor 2 for P1 disk R is shaded.
:5V
Sensor 2 for P1 disk R is not shaded.
:0V
Replace sensor 2 (34085-1330) for the P1 disk R.
(See 6.10.3.2.)
Yes
Is the voltage between 3-2 pins of connector J6 on the
R motor CPU board (34085-BA04) as described
No
below?
Sensor 2 for P2 disk R is shaded.
:5V
Sensor 2 for P2 disk R is not shaded.
:0V
Replace sensor 2 (34085-1330) for the P2 disk R.
(See 6.10.3.3.)
Yes
Replace the R motor driver board (34085-BA05).
(See 6.16.)
Is the symptom relieved?
No
Yes
Completion
4-6
Replace the R motor CPU board (34085-BA04).
(See 6.15.)
MRT10*RDA001A/E
4.2.3 The L disk AS does not turn.
Is the voltage of connector J3 on the L motor CPU
board (34085-BA02) as described below?
No
A3-A1 pins
:DC+5V
A4-A1 pins
:DC+16.5V
Replace the MB main board (34085-BA01). (See 6.17.)
Yes
Is the voltage of connector P1 on the L motor CPU
board (34085-BA02) as described below?
No
1-3 pins :DC+5V
11-1 pins :DC+16.5V
Replace the L motor CPU board (34085-BA02).
(See 6.13.)
Yes
Is the voltage as described below when disconnecting
each connector on the L motor CPU board (34085BA02)?
No
1-2 pins of connector J4
:DC+5V
1-2 pins of connector J5
:DC+5V
1-2 pins of connector J6
:DC+5V
1-2 pins of connector J7
:DC+5V
Replace the L motor CPU board (34085-BA02).
(See 6.13.)
Yes
Does motor SCA (34085-1310) for the S2 disk L Yes
break?
Replace motor SCA (34085-1310) for the S2 disk L.
(See 6.11.1.1.)
No
Does motor SCA (34085-1310) for the S1 disk L Yes
break?
Replace motor SCA (34085-1310) for the S1 disk L.
(See 6.11.1.3.)
No
Does motor SCA (34085-1310) for the C2 disk L Yes
break?
Replace motor SCA (34085-1310) for the C2 disk L.
(See 6.11.1.2.)
No
Does motor SCA (34085-1310) for the C1 disk L Yes
break?
Replace motor SCA (34085-1310) for the C1 disk L.
(See 6.11.1.5.)
No
Does motor SCA (34085-1310) for the A1 disk L Yes
break?
Replace motor SCA (34085-1310) for the A1 disk L.
(See 6.11.1.4.)
No
Does motor SCA (34085-1310) for the A2 disk L Yes
break?
No
4-7
Replace motor SCA (34085-1310) for the A2 disk L.
(See 6.11.1.6.)
MRT10*RDA001A/E
Does motor PCA (34085-1320) for the CA disk L Yes
break?
Replace motor PCA (34085-1320) for the CA disk L.
(See 6.11.2.1.)
No
Does motor PCA (34085-1320) for the PA disk L Yes
break?
Replace motor PCA (34085-1320) for the P1 disk L.
(See 6.11.2.2.)
No
Does motor PCA (34085-1320) for the P2 disk L Yes
break?
No
Is the voltage between 3-2 pins of connector J4 on the
L motor CPU board (34085-BA02) as described
No
below?
Sensor 2 for the CA disk R is shaded.
:5V
Sensor 2 for the CA disk R is not shaded :0V
Replace motor PCA (34085-1320) for the P2 disk L.
(See 6.11.2.3.)
Replace sensor 2 (34085-1330) for the CA disk L.
(See 6.11.3.1.)
Yes
Is the voltage between 3-2 pins of connector J5 on the
L motor CPU board (34085-BA02) as described
No
below?
Sensor 2 for the P1 disk is shaded.
:5V
Sensor 2 for the P1 disk is not shaded.
:0V
Replace sensor 2 (34085-1330) for the P1 disk L.
(See 6.11.3.2.)
Yes
Is the voltage between 3-2 pins of connector J6 on the
L motor CPU board (34085-BA02) as described
No
below?
Sensor 2 for the P2 disk R is shaded.
:5V
Sensor 2 for the P2 disk R is not shaded. :0V
Replace sensor 2 (34085-1330) for the P2 disk L.
(See 6.11.3.3.)
Yes
Replace the L motor driver board (34085-BA03).
(See 6.14.)
Is the symptom relieved?
No
Yes
Completion
4-8
Replace the L motor CPU board (34085-BA02).
(See 6.13.)
MRT10*RDA001A/E
4.2.4 The PD and convergence of the MB is not initialized properly.
Turn OFF the main switch. Does the driving gear of
No
the step-out motor turn smoothly when turning it by
hand?
Adjust the engagement of the PD gear that does not
turn smoothly.
Yes
Is the MB initial pulse the same as the one on the label No
attached to the upper rear cover (34085-2900)?
Set the MB initial pulse to a proper one. (See 7.2.1.)
Yes
Does the PI sensor board (34085-BA08) for PD of the Yes
upper brace R (34085-2500) break?
Replace the PI sensor board (34085-BA08) for PD of
the upper brace R (34085-2500). (See 6.9.2.1.)
No
Does the PI sensor board (34085-BA08) for CON of Yes
the upper brace R (34085-2500) break?
Replace the PI sensor board (34085-BA08) for CON of
the upper brace R (34085-2500). (See 6.9.1.1.)
No
Does the PI sensor board (34085-BA08) for PD of the Yes
upper brace L (34085-2600) break?
Replace the PI sensor board (34085-BA08) for PD of
the upper brace R (34085-2600). (See 6.9.2.2.)
No
Does the PI sensor board (34085-BA08) for CON of Yes
the upper brace L (34085-2600) break?
No
Replace the MB main board (34085-BA01). (See 6.17.)
4-9
Replace the PI sensor board (34085-BA08) for CON of
the upper brace L (34085-2600). (See 6.9.1.2.)
MRT10*RDA001A/E
4.2.5 The right disk of the MB is not initialized properly.
Turn OFF the main switch. Does the driving gear of
No
the step-out motor turn smoothly when turning it by
hand?
Adjust the gear engagement of the disk, axis and such
that do not turn smoothly.
Yes
Is the MB initial pulse the same as the one on the label No
attached to the upper rear cover (34085-2900)?
Set the MB initial pulse to a proper one. (See 7.2.1.)
Yes
Is the voltage between 3-2 pins of connector J4 on the
R motor CPU board (34085-BA04) as described
No
below?
Sensor 2 for the CA disk R is shaded.
:5V
Sensor 2 for the CA disk R is not shaded. :0V
Replace the sensor 2 (34085-1330) for the CA disk R.
(See 6.10.3.1.)
Yes
Is the voltage between 3-2 pins of connector J5 on the
R motor CPU board (34085-BA04) as described
No
below?
Sensor 2 for the P1 disk R is shaded.
:5V
Sensor 2 for the P1 disk R is not shaded. :0V
Replace the sensor 2 (34085-1330) for the P1 disk R.
(See 6.10.3.2.)
Yes
Is the voltage between 3-2 pins of connector J6 on the
R motor CPU board (34085-BA04) as described
No
below?
Sensor 2 for the P2 disk R is shaded.
:5V
Sensor 2 for the P2 disk R is not shaded. :0V
Replace sensor 2 (34085-1330) for the P2 disk R.
(See 6.10.3.3.)
Yes
Is the symptom relieved?
No
Yes
Completion
4 - 10
Replace sensor 1R (34085-1180). (See 6.5.1.)
MRT10*RDA001A/E
4.2.6 The left disk of the MB is not initialized properly.
Turn OFF the main switch. Does the driving gear of
No
the step-out motor turn smoothly when turning it by
hand?
Adjust the gear engagement of the disk, axis and such
that do not turn smoothly.
Yes
Is the MB initial pulse the same as the one on the label No
attached to the upper rear cover (34085-2900)?
Set the MB initial pulse to a proper one. (See 7.2.1.)
Yes
Is the voltage between 3-2 pins of connector J4 on the
L motor CPU board (34085-BA02) as described
No
below?
Sensor 2 for the CA disk R is shaded.
:5V
Sensor 2 for the CA disk R is not shaded. :0V
Replace sensor 2 (34085-1330) for the CA disk L.
(See 6.11.3.1.)
Yes
Is the voltage between 3-2 pins of connector J5 on the
L motor CPU board (34085-BA02) as described
No
below?
Sensor 2 for the P2 disk R is shaded.
:5V
Sensor 2 for the P2 disk R is not shaded. :0V
Replace sensor 2 (34085-1330) for the P1 disk L.
(See 6.11.3.2.)
Yes
Is the voltage between 3-2 pins of connector J6 on the
L motor CPU board (34085-BA02) as described
No
below?
Sensor 2 for the P2 disk R is shaded.
:5V
Sensor 2 for the P2 disk R is not shaded. :0V
Replace sensor 2 (34085-1330) for the P2 disk L.
(See 6.11.3.3.)
Yes
Is the symptom relieved?
No
Yes
Completion
4 - 11
Replace sensor 1L (34085-1280). (See 6.5.2.)
MRT10*RDA001A/E
4.3 An error message appears.
Does error 01: communication error CB-MB appear?
Yes
4.3.1 “Error01: Communication Error CB-RB”
appears.
Yes
4.3.2 “Error11: Communication Error CB-RB”
appears.
No
Does error 11: communication error CB-RB appear?
No
Does “No appointment data!!” appear?
Yes
4.3.3 “No appointment data!!” appears.
No
Does “Chart doesn’t work.” appear?
Yes
4.3.4 “Chart doesn’t work.” appears.
No
Does “Setup data is initialized.” appear?
Yes
4.3.5 “Setup data is initialized.” appears.
No
Does “CF card Read Error!!” appear?
Yes
4.3.6 “CF card -- Read Error!!” appears.
No
Does “CF card -- Write Error !!” appear?
Yes
4.3.7 “CF card -- Write Error !!” appears.
No
Does “CF card -- File Error” appear?
Yes
4.3.8 “CF card -- File Error” appears.
No
Does “CF card -- File not found!!” appear?
Yes
4.3.9 “CF card -- File not found!!” appears.
No
Does “CF card -- Card not found!!” appear?
Yes
4.3.10“CF card -- Card not found!!” appears.
No
Does “No data!!” appear?
Yes
No
Completion
4 - 12
4.3.11 “No data!!” appears.
MRT10*RDA001A/E
4.3.1 “Error 01: Communication Error CB-MB” appears.
Is the voltage of the following connector on the RB I/F
No
board (834085-BA22) as described below?
A1-A4 pins of connector J5: DC+5V
A12-A8 pins of connector J5: DC+15V
Replace the RB I/F board (34085-BA22). (See 6.27.)
Yes
Does cable MB break?
Yes
Replace cable MB.
No
Does the MB work properly?
No
4.2 Initialization is not completed properly.
Yes
Does cable CB break?
Yes
Replace cable CB.
No
Replace the RB I/F board (834085-BA22). (See 6.27.)
Is the symptom relieved?
Yes
No
Replace the CB main board (34085-BA11).
(See 6.19.)
4 - 13
Completion
MRT10*RDA001A/E
4.3.2 “Error 11: Communication Error CB-RB” appears.
Does cable CB break?
Yes
Replace cable CB.
No
Replace the RB I/F board (34085-BA22). (See 6.27.)
Is the symptom relieved?
Yes
Completion
No
Replace the RB main board (34085-BA21). (See 6.26.)
Is the symptom relieved?
Yes
Completion
No
Replace the CB main board (34085-BA11). (See 6.19.)
4.3.3 “No appointment data!!” appears.
Are the AR and LM connected?
No
Connect the AR and LM.
Yes
Is the power of AR and LM on?
No
Turn on the power of the AR and LM.
Yes
Does the communication cable break?
Yes
No
It is assumed that the AR and LM might malfunction.
See the service manual for the malfunctioned device.
4 - 14
Replace the communication cable.
MRT10*RDA001A/E
4.3.4 “Chart doesn’t work.” appears.
Is the chart projector connected?
No
Connect the chart projector.
Yes
Is the power of the chart projector ON?
No
Turn ON the power of the chart projector.
Yes
Is the chart projector applied to, or set for the RT- No
5100?
Change the chart projector to the one applied to the
RT-5100, or change the setting of the chart projector to
the applied one.
Yes
Do you try to change the chart while the chart is Yes
moving?
It is recommended not to change the chart while the
chart is moving.
No
Does the communication cable break?
Yes
Replace the communication cable.
No
Does cable CB break?
Yes
Replace cable CB.
No
Replace the RB I/F board (34085-BA22). (See 6.27.)
Is the symptom relieved?
No
Yes
Completion
4 - 15
Replace the RB main board (34085-BA21). (See 6.26.)
MRT10*RDA001A/E
4.3.5 “Setup data is initialized.” appears.
Keep the power ON for approximately 8 hours to
charge the battery in the control box.
Is the symptom relieved?
No
Replace the CB main board (34085-BA11). (See 6.19.)
Yes
Completion
4.3.6 “CF card -- Read Error!!” appears.
Is the compact flash memory card inserted?
No
Insert the compact flash memory card.
Yes
Can another compact flash memory card be used?
No
Replace the CB main board (34085-BA11). (See 6.19.)
Yes
Replace the compact flash memory card.
4.3.7 “CF card -- Write Error!!” appears.
Perform the procedures described in “4.3.6.”
4.3.8 “CF card -- File Error!!” appears.
It is assumed that the specified image file stored in the compact flash memory card might be
broken. Check the file.
4.3.9 “CF card -- File not found!!” appears.
The specified image file may not be stored in the compact flash memory card. Check the file.
4.3.10 “CF card -- Card not found!!” appears.
Insert the compact flash memory card.
4.3.11 “No data!!” appears.
Check the IC card and data in the IC card.
4 - 16
MRT10*RDA001A/E
4.4 The instrument cannot be operated with the control box.
Can the instrument be operated with the switches?
No
4.4.1 The instrument cannot be operated with the
switches.
No
4.4.2 The instrument cannot be operated by turning the
dial.
No
4.4.3 The instrument cannot be operated with the touch
panel.
Yes
Can the instrument be operated by turning the dial?
Yes
Can the instrument be operated with the touch panel?
Yes
Completion
4.4.1 The instrument cannot be operated with the switches.
Replace the KEY I/F board (34085-BA12). (See 6.20.)
Is the symptom relieved?
Yes
No
Replace the CB main board (34085-BA11). (See 6.19.)
4 - 17
Completion
MRT10*RDA001A/E
4.4.2 The instrument cannot be operated by turning the dial.
Replace the rotary encoder (34085-E202). (See 6.22)
Is the symptom relieved?
Yes
Completion
No
Replace the KEY I/F board (34085-BA12). (See 6.20.)
Is the symptom relieved?
Yes
Completion
No
Replace the CB main board (34085-BA11). (See 6.19.)
4.4.3 The instrument cannot be operated with the touch-screen panel.
Perform the position adjustment of the touch-screen
panel. (See 7.13.)
Is the symptom relieved?
Yes
Completion
No
Does cable LCD2 (34085-E304) break?
Yes
Replace cable LCD2 (34085-E304).
No
Replace the color LCD module (42203-E016).
(See 6.25.)
Is the symptom relieved?
Yes
No
Replace the CB main board (34085-BA11). (See 6.19.)
4 - 18
Completion
MRT10*RDA001A/E
4.5 The compact flash memory card cannot be used.
Is the compact flash memory card inserted?
No
Insert the compact flash memory card.
Yes
Can another compact flash memory card be used Yes
properly?
Replace the compact flash memory card.
No
Replace the CB main board (34085-BA11). (See 6.19.)
4.6 The IC card cannot be used.
Can the IC card be inserted?
No
Insert the IC card.
Yes
Can another IC card be used properly?
Yes
No
Replace the CB main board (34085-BA11). (See 6.19.)
4 - 19
Replace the IC card.
MRT10*RDA001A/E
4.7 The printer does not print.
Is the printing paper jammed inside of the printer?
Yes
Remove the jammed printing paper.
No
Does cable PR (34085-E022) break?
Yes
Replace cable PR (34085-E022).
No
Is the operating sound of the printer heard?
No
Replace the thermal printer (34085-E020).
Yes
Are characters or lines printed partially?
No
Replace the thermal printer (34085-E020).
Yes
Is the symptom relieved by increasing the printing No
density?
Replace the thermal printer (34085-E020).
Yes
Replace the RB I/F board (34085-BA21).
Is the symptom relieved?
No
Yes
Completion
4 - 20
Replace the RB main board (34085-BA21).
MRT10*RDA001A/E
4.8 The communication with the auto refractometer or lensmeter
cannot be done.
Are the auto refractometer and lensmeter that accept No
the communication with the RT-5100 used?
Use the auto refractometer and lensmeter that accept
the communication with the RT-5100.
Yes
Is the setting that enables the communication with the No
auto refractometer and lensmeter selected?
Select the setting that enables the communication with
the auto refractometer or lensmeter.
Yes
Is the communication cable connected properly?
No
Connect the communication cable properly.
(Refer to the operator’s manual.)
Yes
Does the communication cable break?
Yes
Replace the communication cable.
Ｎｏ
Is the communication setting of the auto refractometer No
and lensmeter correct?
Select the communication setting of the auto
refractometer and lensmeter correctly.
(Refer to the operator’s manual.)
Yes
Is the setting of the auto refractometer and lensmeter No
printed when communicating with a memory function?
Be sure to print the setting of the auto refractometer
and lensmeter prior to the communication when
communicating with a memory function.
Yes
Replace the RB main board (34085-BA21). (See 6.22.)
Is the symptom relieved?
No
Yes
Completion
4 - 21
Auto refractometer or lensmeter malfunctions.
Repair the auto refractometer or lensmeter.
MRT10*RDA001A/E
4.9 The chart projector does not work as specified with the control
box.
Is the setting to work with the chart projector selected?
No
Select the setting to work with the chart projector.
Yes
Is the setting of the chart type selected correctly?
No
Select the correct chart type.
Yes
Is the communication cable with the chart projector No
connected properly?
Connect the communication cable of the chart
correctly. (Refer to the operator’s manual.)
Yes
Does the communication cable of the chart projector Yes
break?
Repair the communication cable of the chart projector
or replace it.
No
Replace the RB main board (34085-BA21). (See 6.26.)
Is the symptom relieved?
No
Yes
Completion
4 - 22
Chart projector malfunctions.
Repair the chart projector.
MRT10*RDA001A/E
§5 REMOVING COVERS
5.1 Covers of the main body
5.1.1 Face shields R and L
1. Remove the face shield R (34085-1850) and
L (34085-1950).
5.1.2 Rear covers
5.1.2.1 Rear cover R
1. Remove the face shield R (34085-1850).
(See 5.1.1.)
2. Remove the cap (32105-M730).
3. Unscrew PC2.6×6 (n=3) to remove the rear
cover R (34085-1800).
4. Reassemble the parts in reverse order.
2%˜
5.1.2.2 Rear cover L
1. Remove the face shield (34085-1950).
(See 5.1.1.)
2. Remove the cap (32105-M730).
3. Unscrew PC2.6×6 (n=3) to remove the rear
cover L (34085-1900).
4. Reassemble the parts in reverse order.
2%˜
5- 1
MRT10*RDA001A/E
5.1.3 Front covers
5.1.3.1 Front cover R
1. Remove the rear cover R (34085-1800).
(See 5.1.2.)
2. Unscrew PT3×6 (n=3) and remove the front
cover R (34085-1600).
3. Reassemble the parts in reverse order.
26˜
5.1.3.2 Front cover L
1. Remove the rear cover L (34085-1900).
(See 5.1.2.)
2. Unscrew PT3×6 (n=3) and remove the front
cover L (34085-1700).
3. Reassemble the parts in reverse order.
26˜
5.1.4 Knob S AS
1. Remove the knob S AS (34085-2210).
5-2
MRT10*RDA001A/E
5.1.5 Upper cover J
1. Remove the upper cover J (34085-M259).
5.1.6 Upper rear cover
%#$.'/$
1. Remove the upper cover J (34085-M259).
(See 5.6.)
2. Remove the cable MB.
3. Remove the caps (32105-M730, n=2) and
PC3×6 (n=3).
4. Remove the rear cover.
5. Reassemble the parts in reverse order.
2%˜
5.1.7 Upper cover F
1. Remove the knob S AS (34085-2210).
26˜
(See 5.1.4.)
2. Tilt the holder AS (34085-2220) toward the
front.
3. Unscrew PC3×6 and PT3×6 (n=2) and
remove the upper cover F (34085-M257).
4. Reassemble the parts in reverse order.
5-3
2%˜
MRT10*RDA001A/E
5.2 Control box covers
5.2.1 Rear cover AS
1. Remove the cap (32105-M730, n=2).
2. Unscrew PC3×6 (n=2) and remove the rear
cover AS (34085-4300).
3. Reassemble the parts in reverse order.
2%˜
5.2.2 EMC cover
1. Unscrew the tight screw P (825053-CE06B,
n=5) and PC3×6 to remove the lower cover
(34085-M402).
2. Remove the EMC cover (34085-M418).
3. Reassemble the pars in reverse order.
%'$
2%˜
5-4
MRT10*RDA001A/E
§6 REPLACEMENT
* For the marked ( ) procedures in this section, see the adjustment precautions in §2 SAFETY
PRECAUTIONS.
6.1 Battery AS
Replacement part: 34085-1000
1. Remove the covers. (See 5.1.)
2. Remove the MB main board (34085-BA01).
(See 6.17.)
3. Replace the right side of the battery AS.
* Viewed from the patient’s side
1) Remove connector J3 on the motor CPU
board (34085-BA02).
2) Unscrew HH3×3 (n=2) and SB3×8 (n=2).
Replace the right side of the battery AS
(34085-1000).
**˜
5$˜
4. Replace the left side of the battery AS.
* Viewed from the patient’s side
1) Remove connector J3 on the R motor
CPU board (34085-BA04).
2) Unscrew HH3×3 (n=2) and SB3×8 (n=2).
Replace the left side of the battery AS
(34085-1000).
5. Reassemble the parts in reverse order.
**˜
5$˜
6-1
MRT10*RDA001A/E
6.2 Disk AS
6.2.1 R disk AS (
)
Replacement part: 34085-1100
1. Remove the covers. (See 5.1.)
2. Unscrew the small pan head screw (82053CE05A, n=2) and replace the R disk AS
(34085-1100).
3. Reassemble the parts in reverse order.
6.2.2 L disk AS (
%'#
)
Replacement part: 34085-1200
1. Remove the covers. (See 5.1.)
2. Unscrew the small pan head screw (82053CE05A, n=2) and replace the L disk AS
(34085-1200).
3. Reassemble the parts in reverse order.
%'#
6.3 Boards R and L
6.3.1 Board R
Replacement part: 34085-1360
1. Remove the covers. (See 5.1.)
2. Remove connectors J2 to J8 on the R motor
CPU board (34085-BA02).
3. Remove connectors J2 to J10 on the R motor
DRIVER board (34085-BA03).
4. Unscrew the small pan head screw (82053CE05A, n=2) and replace the board R
(34085-1360).
5. Reassemble the parts in reverse order.
%'#
6-2
MRT10*RDA001A/E
6.3.2 Board L
Replacement part: 34085-1460
1. Remove the covers. (See 5.1.)
2. Remove connectors J2 to J8 on the L motor
CPU board (34085-BA04).
3. Remove connectors J2 to J10 on the L motor
driver board (34085-BA05).
4. Remove the pan head screw (82053-CE05A,
n=2) and replace the board L (34085-1460).
5. Reassemble the parts in reverse order.
%'#
6.4 Plates
6.4.1 Plate FR (
)
Replacement part: 34085-1500
1. Remove the covers. (See 5.1.)
2. Remove connector J2 on the L motor CPU
board (34085-BA02).
3. Remove the pan head screw (82053-CE05A,
n=5) and replace the plate FR (34085-1500).
4. Reassemble the parts in reverse order.
6.4.2 Plate FL (
%'#
)
Replacement part: 34085-1520
1. Remove the covers. (See 5.1.)
2. Remove connector J2 on the R motor CPU
board (34085-BA04).
3. Remove the pan head screw (82053-CE05A,
n=5) and replace the plate FL (34085-1520).
4. Reassemble the parts in reverse order.
6-3
%'#
MRT10*RDA001A/E
6.4.3 Plate BR (
)
Replacement part: 34085-1530
1. Remove the covers. (See 5.1.)
2. Remove the pan head screw (82053CE05A, n=4) and replace the plate BR
(34085-1530).
3. Reassemble the parts in reverse order.
%'#
6.4.4 Plate BL (
)
Replacement unit: 344085-1540
1. Remove the covers. (See 5.1.)
2. Remove the pan head screw (82053CE05A, n=4) and replace the plate BL
(34085-1540).
3. Reassemble the parts in reverse order.
%'#
6.5 Sensor 1
6.5.1 Sensor 1R
Replacement part: 34085-1180
1. Remove the covers. (See 5.1.)
2. Remove connector P7 (J7) on the L motor
CPU board (34085-BA02).
3. Remove the pan head screw (82053CE05A) and replace the sensor 1R.
4. Reassemble the parts in reverse order.
%'#
6-4
MRT10*RDA001A/E
6.5.2 Sensor 1L
Replacement part: 34085-1280
1. Remove the covers. (See 5.1.)
2. Remove connector P7 (J7) on the R motor
CPU board (34085-BA04).
3. Remove the pan head screw (82053-CE05A)
and replace the sensor 1L (34085-1280).
4. Reassemble the parts in reverse order.
%'#
6.6 Frames
6.6.1 Frame R (
)
Replacement part: 34085-1300
1. Remove plate FR (34085-1500), plate BR (34085-1530) and R disk AS (34085-1100). (See
6.2 and 6.4.)
2. Replace frame R (34085-1300).
3. Reassemble the parts in reverse order.
6.6.2 Frame L (
)
Replacement part: 34085-1400
1. Remove the plate FL (34085-1520), plate BL (34085-1540) and L disk AS (34085-1200).
(See 6.2 and 6.4.)
2. Replace the frame L (34085-1400).
3. Reassemble the parts in reverse order.
6.7 PD motors
6.7.1 PD motor R
Replacement part: 34085-2510
1. Remove the covers. (See 5.1.)
2. Unscrew the tight screw P (82053-CE06B,
n=2) and replace the PD motor R (340852510).
3. Reassemble the parts in reverse order.
6-5
%'$
MRT10*RDA001A/E
6.7.2 PD motor L
Replacement part: 34085-2610
1. Remove the covers. (See 5.1.)
2. Unscrew the tight screw P (82053-CE06B,
n=2) and replace the PD motor L (340852610).
3. Reassemble the parts in reverse order.
%'$
6.8 CON motors
6.8.1 CON motor R
Replacement part: 34085-2520
1. Remove the covers. (See 5.1.)
2. Unscrew the tight screw P (82053-CE06B,
n=2) and replace the CON motor R (340852520).
3. Reassemble the parts in reverse order.
%'$
6.8.2 CON motor L
Replacement part: 34085-2620
1. Remove the covers. (See 5.1.)
2. Unscrew the tight screw P (82053-CE06B,
n=2) and replace the CON motor L (340852620).
3. Reassemble the parts in reverse order.
%'$
6-6
MRT10*RDA001A/E
6.9 PI sensor boards
6.9.1 CON sensor
6.9.1.1 CON sensor of the upper brace R
$#
Replacement part: 34085-BA08
1. Remove the covers. (See 5.1.)
2. Remove connector J9 on the MB main
board (34085-BA01).
3. Unscrew the tight screw P (82053-CE06B)
of the upper brace R (34085-2500) and
replace the PI sensor board (34085-BA08).
4. Reassemble the parts in reverse order.
%'$
6.9.1.2 CON sensor of the upper brace L
Replacement part: 34085-BA08
1. Remove the covers. (See 5.1.)
2. Remove connector J11 on the MB main
board (34085-BA01).
3. Unscrew the tight screw P (82053-CE06B)
of the upper brace L (34085-2600) and
replace the PI sensor board (34085-BA08).
4. Reassemble the parts in reverse order.
$#
%'$
6-7
MRT10*RDA001A/E
6.9.2 PD sensors
6.9.2.1 PD sensor of the upper brace R
Replacement part: 34085-BA08
1. Remove the covers. (See 5.1.)
2. Remove connector J8 on the MB main
board (34085-BA01).
3. Unscrew the tight screw P (82053-CE06B)
on the right side (viewed from the patient’s
side) and replace the PI sensor board
(34085-BA08).
4. Reassemble the parts in reverse order.
%'$
$#
6.9.2.2 PD sensor of the upper brace L
Replacement part: 34085-BA08
1. Remove the covers. (See 5.1.)
2. Remove connector J10 on the MB main
board (34085-BA01).
3. Unscrew the tight screw P (82053-CE06B)
on the left side (viewed from the patient’s
side) and replace the PI sensor board
(34085-BA08).
4. Reassemble the parts in reverse order.
6-8
%'$
$#
MRT10*RDA001A/E
6.10 Motors and sensors of frame R
6.10.1 Motor SCA
6.10.1.1 Motor for the S2 disk
Replacement part: 34085-1310
1. Remove the covers. (See 5.1.)
2. Remove connector J2 on the L motor driver
board (34085-BA03).
3. Unscrew HH2×2 (n=2) and remove the
stopper (34085-M053).
4. Remove the double gear (shorter one,
34085-1340) together with the double gear
spindle (34085-M054).
5. Unscrew the pan head screw (82053CE05A, n=2) and replace the motor SCA
(34085-1310).
6. Reassemble the parts in reverse order.
* Adjust the gear engagement at the
position of the motor SCA (34085-1310).
%'#
**˜
6.10.1.2 Motor for the C2 disk
Replacement part: 34085-1310
1. Remove the covers. (See 5.1.)
2. Remove connector J4 on the L motor driver
board (34085-BA03).
3. Unscrew HH2×2 (n=2) and remove the
stopper (34085-M053).
4. Remove the double gear (longer one, 340851350) together with the double gear spindle
(34085-M054).
5. Remove the pan head screw (82053-CE05A,
n=2) and replace the motor SCA (340851310).
6. Reassemble the parts in reverse order.
* Adjust the gear engagement at the
position of the motor SCA (30485-1310).
6-9
**˜
%'#
MRT10*RDA001A/E
6.10.1.3 Motor for the S1 disk
Replacement part: 34085-1310
1. Remove the covers. (See 5.1.)
2. Remove the motor for the S2 disk and the
one for the C2 disk. (See 6.10.1.2 and
6.10.1.3.)
3. Remove connector J3 on the L motor driver
board (34085-BA03).
4. Unscrew HH2×2 (n=2) and remove the
stopper (34085-M053).
5. Remove the double gear (shorter, 820531340) together with the double gear spindle
(34085-M054).
6. Remove the pan head screw (82053CE05A, n=2) and replace the motor SCA
(34085-1310).
7. Reassemble the parts in reverse order.
* Adjust the gear engagement at the
position of the motor SCA (34085-1310).
6.10.1.4 Motor for the A1 disk (
%'#
**˜
)
Replacement part: 34085-1310
1. Remove the plate FR (34085-1500). (See
6.4.1.)
2. Remove connector J6 on the L motor driver
board (34085-BA03).
3. Unscrew HH2×2 (n=2) to remove the
stopper (34085-M053), and remove the
double gear (34085-M057).
4. Remove the pan head screw (82053CE05A, n=2) and replace the motor SCA
(34085-1310).
5. Reassemble the parts in reverse order.
* Adjust the gear engagement at the
position of the motor SCA (34085-1310).
6 - 10
%'#
**˜
MRT10*RDA001A/E
6.10.1.5 Motor for the C1 disk (
)
Replacement part: 34085-1310
1. Remove the plate FR (34085-1500).
(See 6.4.1.)
2. Remove the motor for the A1 disk.
(See 6.10.1.4.)
3. Remove connector J5 on the L motor driver
board (34085-BA03).
4. Unscrew HH2×2 (n=2) to remove the
stopper (34085-M053), and remove the
double gear (34085-M057).
5. Remove the pan head screw (82053CE05A, n=2) and replace the motor SCA
(34085-1310).
6. Reassemble the parts in reverse order.
* Adjust the gear engagement at the
position of the motor SCA (34085-1310).
6.10.1.6 Motor for the A2 disk (
%'#
**˜
)
Replacement part: 34085-1310
1. Remove the plate FR (34085-1500).
(See 6.4.1.)
2. Remove the motor for the A1 disk.
(See 6.10.1.4.)
3. Remove connector J7 on the L motor driver
board (34085-BA03).
4. Unscrew HH2×2 (n=2), and remove the
stopper (34085-M053), and remove the
double gear (34085-M057).
5. Remove the pan head screw (82053CE05A, n=2) and replace the motor SCA
(34085-1310).
6. Reassemble the parts in reverse order.
* Adjust the gear engagement at the
position of the motor SCA (34085-1310).
6 - 11
%'#
**˜
MRT10*RDA001A/E
6.10.2 Motor PCA
6.10.2.1 Motor for the CA disk (
)
Replacement part: 34085-1320
1. Remove the plate BR (34085-1530).
(See 6.4.3.)
%'#
2. Remove connector J8 on the L motor driver
board (34085-BA03).
3. Remove the pan head screw (82053-CE05A,
n=2) and replace the motor PCA (340851320).
6. Reassemble the parts in reverse order.
* Adjust the gear engagement at the position of the motor PCA (34085-1320).
6.10.2.2 Motor for the P1 disk (
)
Replacement part: 34085-1320
1. Remove the plate FR (34085-1500).
(See 6.4.3.)
2. Remove connector J9 on the L motor driver
board (34085-BA03).
3. Remove the pan head screw (82053-CE05A,
n=2) and replace the motor PCA (340851320).
4. Reassemble the parts in reverse order.
* Adjust the gear engagement at the position
of the motor PCA (34085-1320).
6.10.2.3 Motor for the P2 disk (
Replacement part: 34085-1320
1. Remove the plate FR (34085-1500).
(See 6.4.3.)
2. Remove connector J10 on the L motor driver
board (34085-BA03).
3. Remove the pan head screw (82053-CE05A,
n=2) and replace the motor PCA (340851320).
4. Reassemble the parts in reverse order.
* Adjust the gear engagement at the
position of the motor PCA (34085-1320).
6 - 12
%'#
)
%'#
MRT10*RDA001A/E
6.10.3 Sensor 2
6.10.3.1 Sensor for the CA disk (
)
Replacement part: 34085-1330
1. Remove the covers. (See 5.1.)
2. Remove connector J4 on the L motor CPU
board (34085-BA02).
3. Remove the pan head screw (82053-CE05A,
n=2) and replace sensor 2 (34085-1330).
4. Reassemble the parts in reverse order.
6.10.3.2 Sensor for the P1 disk (
%'#
)
Replacement part: 34085-1330
1. Remove the covers. (See 5.1.)
2. Remove connector J5 on the L motor CPU
board (34085-BA02).
3. Remove the pan head screw (82053-CE05A,
n=2) and replace sensor 2 (34085-1330).
4. Reassemble the parts in reverse order.
6.10.3.3 Sensor for the P2 disk (
%'#
)
Replacement part: 34085-1330
1. Remove the covers. (See 5.1.)
2. Remove connector J6 on the L motor CPU
board (34085-BA02).
3. Remove the pan head screw (82053-CE05A,
n=2) and replace sensor 2 (34085-1330).
4. Reassemble the parts in reverse order.
%'#
6 - 13
MRT10*RDA001A/E
6.11 Motors or sensors of frame L
6.11.1 Motor SCA
6.11.1.1 Motor for the S2 disk
Replacement part: 34085-1310
1. Remove the covers. (See 5.1.)
2. Remove connector J2 on the R motor driver
board (34085-BA05).
3. Unscrew HH2×2 (n=2) and remove the
stopper (34085-M053).
4. Remove the double gear (shorter, 340851340) together with the spindle of the double
gear (34085-M054).
5. Remove the pan head screw (82053-CE05A,
n=2) and replace motor SCA (34085-1310).
6. Reassemble the parts in reverse order.
* Adjust the gear engagement at the
position of motor SCA (34085-1310).
%'#
**˜
6.11.1.2 Motor for the C2 disk
Replacement part: 34085-1310
1. Remove the covers. (See 5.1.)
2. Remove connector J4 on the R motor driver
board (34085-BA05).
3. Unscrew HH2×2 (n=2) and remove the
stopper (34085-M053).
4. Remove the double gear (longer, 340851350) together with the spindle of the double
gear (34085-M054).
5. Remove the pan head screw (82053-CE05A,
n=2) and replace motor SCA (34085-1310).
6. Reassemble the parts in reverse order.
* Adjust the gear engagement at the
position of motor SCA (34085-1310).
6 - 14
**˜
%'#
MRT10*RDA001A/E
6.11.1.3 Motor for the S1 disk
Replacement part: 34085-1310
1. Remove the covers. (See 5.1.)
2. Remove the motors for the S2 disk and C2
disk. (See 6.11.1.2 and 6.11.1.3.)
3. Remove connector J3 on the R motor driver
board (34085-BA05).
4. Unscrew HH2×2 (n=2) and remove the
stopper (34085-M053).
5. Remove the double gear (shorter, 340851340) together with the spindle of the double
gear (34085-M054).
6. Remove the pan head screw (82053-CE05A,
n=2) and replace motor SCA (34085-1310).
6. Reassemble the parts in reverse order.
* Adjust the gear engagement at the
position of motor SCA (34085-1310).
6.11.1.4 Motor for the A1 disk (
%'#
**˜
)
Replacement part: 34085-1310
1. Remove plate FL (34085-1520). (See 6.4.2.)
2. Remove connector J6 on the R motor driver
board (34085-BA05).
3. Unscrew HH2×2 (n=2), and remove the
stopper (34085-M053), and remove the
double gear (34085-M057)..
4. Remove the pan head screw (82053-CE05A,
n=2) and replace motor SCA (34085-1310).
5. Reassemble the parts in reverse order.
* Adjust the gear engagement at the
position of motor SCA (34085-1310).
6 - 15
%'#
**˜
MRT10*RDA001A/E
6.11.1.5 Motor for the C1 disk (
Replacement part: 34085-1310
1. Remove plate FL (34085-1520). (See 6.4.2.)
2. Remove the motor for the A1 disk. (See
6.11.1.4.)
3. Remove connector J5 on the R motor driver
board (34085-BA05).
4. Unscrew HH2×2 (n=2), and remove the
stopper (34085-M053), and remove the
double gear (34085-M057).
5. Remove the pan head screw (82053-CE05A,
n=2) and replace motor SCA (34085-1310).
6. Reassemble the parts in reverse order.
* Adjust the gear engagement at the
position of motor SCA (34085-1310).
6.11.1.6 Motor for the A2 disk (
)
%'#
**˜
)
Replacement part: 34085-1310
1. Remove plate FL (34085-1520). (See 6.4.2.)
2. Remove the motor for the A1 disk. (See
6.11.1.4.)
3. Remove connector J7 on the R motor driver
board (34085-BA05).
3. Unscrew HH2×2 (n=2) and remove the
stopper (34085-M053).
4. Unscrew HH2×2 (n=2), and remove the
stopper (34085-M053), and remove the
double gear (34085-M057).
5. Remove the pan head screw (82053-CE05A,
n=2) and replace motor SCA (34085-1310).
6. Reassemble the parts in reverse order.
* Adjust the gear engagement at the
position of motor SCA (34085-1310).
6 - 16
%'#
**˜
MRT10*RDA001A/E
6.11.2 Motor for the PCA disk
6.11.2.1 Motor for the CA disk (
)
Replacement part: 34085-1320
1. Remove plate BL (34085-1540). (See 6.4.4.)
2. Remove connector J8 on the R motor driver
board (34085-BA05).
3. Remove the pan head screw (82053-CE05A,
n=2) and replace motor PCA (34085-1320).
4. Reassemble the parts in reverse order.
* Adjust the gear engagement at the
position of motor PCA (34085-1320).
6.11.2.2 Motor for the P1 disk (
)
Replacement part: 34085-1320
1. Remove plate FL (34085-1520). (See 6.4.4.)
2. Remove connector J9 on the R motor driver
board (34085-BA05).
3. Remove the pan head screw (82053-CE05A,
n=2) and replace motor PCA (34085-1320).
4. Reassemble the parts in reverse order.
* Adjust the gear engagement at the
position of motor PCA (34085-1320).
6.11.2.3 Motor for the P2 disk (
%'#
%'#
)
Replacement part: 34085-1320
1. Remove plate FL (34085-1520). (See 6.4.4.)
2. Remove connector J10 on the R motor driver
board (34085-BA05).
3. Remove the pan head screw (82053-CE05A,
n=2) and replace motor PCA (34085-1320).
4. Reassemble the parts in reverse order.
* Adjust the gear engagement at the
position of motor PCA (34085-1320).
6 - 17
%'#
MRT10*RDA001A/E
6.11.3 Sensor 2
6.11.3.1 Motor for the CA disk (
)
Replacement part: 34085-1330
1. Remove the covers. (See 5.1.)
2. Remove connector J4 on the R motor CPU
board (34085-BA04).
3. Remove the pan head screw (82053-CE05A,
n=2) and replace sensor 2 (34085-1330).
4. Reassemble the parts in reverse order.
%'#
6.11.3.2 Motor for the P1 disk (
)
Replacement part: 34085-1330
1. Remove the covers. (See 5.1.)
2. Remove connector J5 on the R motor CPU
board (34085-BA04).
3. Remove the pan head screw (82053-CE05A,
n=2) and replace sensor 2 (34085-1330).
4. Reassemble the parts in reverse order.
6.11.3.3 Motor for the P2 disk (
)
Replacement part: 34085-1330
1. Remove the covers. (See 5.1.)
2. Remove connector J6 on the R motor CPU
board (34085-BA04).
3. Remove the pan head screw (82053-CE05A,
n=2) and replace sensor 2 (34085-1330).
4. Reassemble the parts in reverse order.
%'#
6 - 18
%'#
MRT10*RDA001A/E
6.12 VD LED unit
6.12.1 VD LED unit of frame R
Replacement part: 34085-EA02
1. Remove the covers. (See 5.1.)
2. Remove connector J8 on the L motor CPU
board (34085-BA02).
3. Remove the pan head screw (82053-CE05A,
n=2) and 5W30A, and replace the VD LED
unit (34085-EA02).
4. Reassemble the parts in reverse order.
'#
9#
%'#
6.12.2 VD LED unit of frame L
Replacement part: 34085-EA02
1. Remove the covers. (See 5.1.)
2. Remove connector J8 on the R motor CPU
board (34085-BA04).
3. Remove the pan head screw (82053-CE05A,
n=2) and 5W30A, and replace the VD LED
unit (34085-EA02).
4. Reassemble the parts in reverse order.
'#
9#
%'#
6 - 19
MRT10*RDA001A/E
6.13 L motor CPU board
Replacement part: 34085-BA02
1. Remove board L (34085-1460). (See 6.3.2.)
2. Replace the L motor CPU board (34085BA02).
3. Reassemble the parts in reverse order.
$#
$#
6.14 L motor driver board
Replacement part: 34085-BA03
1. Remove board L (34085-1460). (See 6.3.2.)
2. Replace the L motor driver board (34085-BA02). (See 6.13.)
3. Reassemble the parts in reverse order.
6.15 R motor CPU board
Replacement part: 34085-BA04
1. Remove board R (34085-1360). (See 6.3.1.)
2. Replace the R motor CPU board (34085BA04).
3. Reassemble the parts in reverse order.
$#
$#
6.16 R motor driver board
Replacement part: 34085-BA05
1. Remove board R (34085-1360). (See 6.3.1.)
2. Replace the R motor driver board (34085-BA05). (See 6.15.)
3. Reassemble the parts in reverse order.
6 - 20
MRT10*RDA001A/E
6.17 MB main board
Replacement part: 34085-BA01
1. Remove the covers. (See 5.1.)
2. Unscrew PC2.6×4 (n=2) and remove plate
EMC (34085-M217) and cover holder
(34085-M218).
3. Remove all the connectors on the MB main
board (34085-BA01).
4. Unscrew PC3×4 (n=4) and replace the MB
main board (34085-BA01).
5. Reassemble the parts in reverse order.
* Never fail to reattache the memory (IC16)
on the new MB main board.
2%˜
2%˜
$#
6.18 LCD AS
Replacement part: 34085-4200
1. Remove the rear cover AS (34085-4300).
(See 5.2.1.)
2. Unscrew CK2.6×4 and remove the brace
59
cover (34085-M419).
29
3. Remove connectors J12 and J13 on the CB
main board (34085-BA11).
2%˜
4. Remove PC3×6 (n=1) and the sensor panel
(34085-M421).
5. Remove PC4×8 (n=4), SW4 (n=4) and PW4
(n=4). Turn the LCD AS (34085-M421)
backward and move it toward the back to
replace it.
6. Reassemble the parts in reverse order.
%-˜
6 - 21
MRT10*RDA001A/E
6.19 CB main board
Replacement part: 34085-BA11
1. Remove the EMC cover (34085-M418).
(See 5.2.2.)
2. Unscrew CK2.6×4 and remove the brace
cover (34085-M419). (See 6.18.)
3. Remove connectors J12 and J13 on the CB
main board (34085-BA11).
4. Remove PT3×6 (n=5) and PC3×6 (n=2), and
remove the CB main board (34085-BA11)
together with the connector plate (34085M417) and the link board (34085-BA14).
5. Unscrew CK2.6×4 (n=2), and remove the
link board (34085-BA14) together with the
connector plate (34085-M417), and replace
the CB main board (34085-BA11).
6. Reassemble the parts in reverse order.
$#
26˜
2%˜
$#
%-˜
6.20 Key I/F board
Replacement part: 34085-BA12
1. Remove the CB main board (34085-BA11).
(See 6.19.)
2. Remove the gasket (35015-M229, n=2).
3. Unscrew PT3×5 (n=7) and replace the key
I/F board (34085-BA12).
4. Reassemble the parts in reverse order.
6 - 22
$#
26˜
MRT10*RDA001A/E
6.21 Link board
$#
Replacement part: 34085-BA14
1. Remove the EMC cover (34085-M418).
(See 5.2.2.)
2. Unscrew CK2.6×4 (n=2) and replace the link
board (34085-BA14).
3. Reassemble the parts in reverse order.
%-˜
6.22 Rotary encoder
Replacement part: 34085-E202
1. Remove the EMC cover (34085-M418).
(See 5.2.2.)
2. Remove connector J21 on the key I/F board
(34085-BA12).
3. Remove the attached nut of the rotary
encoder (34085-E202) and replace the rotary
encoder.
4. Reassemble the parts in reverse order.
'
ઃዻࡢ࠶ࠪࡖ࡯
Washer
ઃዻ࠽࠶࠻
Nut
6 - 23
MRT10*RDA001A/E
6.23 LCD I/F board
Replacement part: 34085-BA13
1. Remove the LCD AS (34085-420).
(See 6.18.)
2. Remove the cap (32105-M730, n=4).
3. Unscrew PC3×4 (n=4) and remove the rear
LCD cover (34085-M432).
2%˜
4. Remove all the connectors on the LCD I/F
board (34085-BA13).
5. Unscrew CK2.6×5 (n=2) and remove the
LCD I/F board (34085-BA13).
6. Reassemble the parts in reverse order.
%-˜
$#
6.24 Inverter
Replacement part: 42203-E017
1. Remove the LCD AS (34085-4200).
(See 6.18.)
2. Remove the rear LCD cover (34085-M432).
(See 6.23.)
3. Remove all the connectors of the inverter
(42203-E017).
4. Unscrew CK2.6×5 (n=2) replace the inverter
(42203-E017).
5. Reassemble the parts in reverse order.
%-˜
'
6 - 24
MRT10*RDA001A/E
6.25 Color LCD module
Replacement part: 42203-E016
1. Remove the LCD AS (34085-4200).
(See 6.18.)
2. Remove the rear LCD cover (34085-M432).
(See 6.23.)
3. Remove connector CN101 of the inverter
(42203-E017).
4. Remove connector J34 on the LCD I/F board
(34085-BA13).
5. Remove connector CN01 of the color LCD
module (42203-E016).
%'$
6. Unscrew CK2.6×5 (n=4) and replace the
color LCD module (42203-E016).
7. Reassemble the parts in reverse order.
%-˜
'
6 - 25
MRT10*RDA001A/E
6.26 RB main board
* SW2
$#
Replacement part: 34085-BA21
1. Remove all the connectors connected to the
RB.
2. Remove the RB from the system table.
3. Unscrew PC3×4 (n=5) and PC2.6×5 (n=2),
and remove the RB main board (34085BA21) together with the RB I/F board
(34085-BA22).
4. Unscrew PC3×4 (n=4) and replace the RB
main board (34085-BA21).
5. Reassemble the parts in reverse order.
* Verify that the SW2 on the RB main board
is set to the “normal” position.
* It is unnecessary to reattach the memory
(IC24) on the new RB main board.
2%˜
$#
2%˜
$#
2%˜
##
$#
6.27 RB I/F board
Replacement part: 34085-BA22
1. Remove all the connectors connected to the RB.
2. Remove the RB from the system table.
3. Remove the RB main board (34085-BA21) together with the RB I/F board (34085-BA22).
(See 6.26.)
4. Unscrew PC3×4 (n=4) and replace the RB main board (34085-BA21). (See 6.26.)
5. Reassemble the parts in reverse order.
6 - 26
MRT10*RDA001A/E
§7 ADJUSTMENT
7.1 Entering the Information/Adjustment screen
1. Press the Shift and Menu keys on the control
box to enter the Information/Adjustment
screen.
2. Press the button of the desired item to
perform the adjustment and print the
information.
Information / Adjustment
Status Information
Chart Selection
Pulse for MB Initialize
Adusting for Chart/Mask
Reset the Setup Data
Adjusting for Mirror (SSC)
Other Brand AR/LM Comm.
End
7.2 Adjustment mode of the MB
7.2.1 Adjustment of the initial pulse for the MB
1. Set DIP switch No. 1 of the MB to the ON position to turn the power on.
* Or, set DIP switch No.1 of the MB to
Pulse for MB Initialize
the ON position and press [Clear] on
㪣
㪩
㪩
the screen of the control box.
㪄㪇㪇㪇㪋 㪪 㪉 㪂㪇㪇㪈㪉
㪂㪇㪇㪊㪇
2. Select the disk to be changed.
㪄㪇㪇㪇㪋 㪪 㪈 㪂㪇㪇㪇㪇
㪂㪇㪇㪊㪇
* The types of the disk are listed in the
㪄㪇㪇㪈㪉 㪚 㪉 㪂㪇㪇㪈㪊
㪂㪇㪇㪋㪋
order viewed from the patient toward the
MB.
㪄㪇㪇㪈㪋 㪚 㪈 㪂㪇㪇㪉㪇
㪂㪇㪇㪇㪍
3. Turn the dial of the control box to change
㪄㪇㪇㪈㪊 㪘 㪈 㪂㪇㪇㪈㪎
the pulse for MB initialize.
㪄㪇㪇㪈㪍 㪘 㪉 㪂㪇㪇㪈㪌
4. Press [Clear] of the control box after
㪂㪇㪇㪏㪇 㪚 㪘 㪂㪇㪇㪋㪇
changing it.
* Pressing [Clear] of the control box will
exit from the adjustment mode.
7-1
㪣
㪧㪈
㪄㪇㪇㪍㪌
㪧㪉
㪂㪇㪇㪇㪇
㪧㪛
㪄㪇㪈㪊㪇
㪚㪇
㪄㪇㪇㪈㪎
MRT10*RDA001A/E
7.2.2 Lens cleaning mode
1. Remove the covers.
2. Set DIP switch No.2 of the MB to the ON
position and turn the power on.
* Or, set DIP switch No.2 of the MB to the
ON position and press [Clear] on the
screen of the control box.
3. Select the disk to be changed.
* The types of the disk are listed in the order
viewed from the patient toward the MB.
4. Turn the dial of the control box to turn the
specified disk.
5. Clean the lens.
6. Press [Clear] of the control box after
cleaning.
* Pressing [Clear] of the control box will
exit from the lens cleaning mode.
Cleaning Lenses
㪣
㪩
㪩
㪣
㪪㪉
㪧㪈
㪪㪈
㪧㪉
㪚㪉
㪧㪛
㪚㪈
㪚㪇
㪘㪈
BIN
㪘㪉
㪚㪘
7.2.3 Adjustment mode for gear
1. Set DIP switch No.3 of the MB to the ON position and turn the power on.
* Or, set DIP switch No.3 of the MB to the ON position and press [Clear] on the screen of
the control box.
2. Select the disk that the gear is to be adjusted.
Adjusting for Gear
㪣
㪣
㪩
㪩
* The types of the disk are listed in the order
㪪
㪉
㪧
㪈
viewed from the patient toward the MB.
3. Turn the dial of the control box to adjust the
㪪㪈
㪧㪉
gear.
㪚㪉
㪧㪛
1) Binocular mode: when pressing either R
㪚㪈
㪚㪇
or L, the same disks for both R and L will
BIN
㪘㪈
be specified.
* The [BIN] button is highlighted.
㪘㪉
2) Monocular mode: when pressing either R
㪚㪘
or L, only the selected disk will be
specified.
* The highlighted [BIN] button returns.
4. Press [Clear] of the control box after
adjustment.
* Pressing [Clear] of the control box will
exit from the adjusting mode for gear.
7-2
MRT10*RDA001A/E
7.3 Chart selection
1. Enter the Information / Adjustment screen. (See 7.1.)
Chart Selection
2. Press [Chart Selection] to enter the Chart
SSC-330 type U
Selection screen.
SSC-300/330 type...
* The chart type that is selected at present
U
UK
is displayed on the screen.
3. The desired chart type can be selected by
CP-670 type...
pressing the chart type.
U
UK
* When connecting the SSC-300 series,
CP-690 type...
select the SSC-330 series.
U
UK
4. Press [Clear] or turn the power off and on
to change the setting to the specified chart
2TGUU=%NGCT?MG[CHVGTUGNGEVKPIEJCTV
type.
7.4 Chart adjustment
1. Enter the Information / Adjustment screen. (See 7.1.)
2. Press [Adjusting for Chart / Mask].
3. Adjust the chart position.
1) Pressing the up-arrow button on the Chart
side: The chart moves upward.
2) Pressing the down-arrow button on the
Chart side: The chart moves downward.
4. Adjust the mask position.
1) Pressing the up-arrow button on the Mask
side: The mask moves upward.
2) Pressing the down-arrow button on the
Mask side: The mask moves downward.
5. Pressing [End] returns to the Adjusting
for Chart / Mask screen.
Adjusting for Chart/Mask
Chart
Mask
End
7.5 Mirror adjustment
1. Enter the Information / Adjustment screen.
(See 7.1.)
2. Press [Adjusting for Mirror (SSC)] to enter
the Adjusting for Mirror (SSC) screen.
* When the chart other than the SSC is
selected, this screen cannot be entered.
3. Move the RT head to the upper limit so that
the chart can be seen in the middle, and press
[Set].
4. Pressing [End] returns to the Adjusting for
Chart / Mask screen.
Adjusting for Mirror (SSC)
Adjust the SSC mirror.
Move the RT head up or down so the chart is seen
in the window.
Then press [Set] key.
Set
End
7-3
MRT10*RDA001A/E
7.6 Parameter setting
1.
2.
3.
4.
Press [Para.] on the Main Menu screen.
The Parameter screen appears.
Select the desired item to be changed.
Follow the procedures below to change the
page of the Parameter screen.
1) Pressing [Back]: displays the previous
page.
2) Pressing [Next]: displays the next page.
3) Pressing [Nex] on the last page of the
screen displays the first page of the screen.
4) Pressing [Back] on the first page of the
screen displays the last page of the screen.
Parameters
Page : 1
SPH step
0.25 D
CYL mode
䋭
AXIS step
5
SPH step (Shift)
1.00 D
CYL step (Shift)
1.00 D
AXIS step (Shift)
1→5 / 5→1
AXIS auto step
0.00 D
Cross cylinder (XC) test
Auto
XC mode S.E. fix
Yes
CYL mode S.E. fix
No
Back
Next
End
7.7 Printing the adjustment value
1. Printing the Status Information.
1) Enter the Information / Adjustment
screen. (See 7.1.)
2) Press [Status Information] to print the
status information.
2. Printing the initial pulse for the MB
1) Enter the Information / Adjustment
screen. (See 7.1.)
2) Press [Pulse for MB Initialize] to print the
initial pulse for the MB.
Information / Adjustment
Status Information
Chart Selection
Reset the Setup Data
㧹㧮ೋᦼࡄ࡞ࠬ
Do you initialize the setup
Adjusting for Chart / Mask
data?
Yes
No
Ꮏ႐಴⩄ߩ⸳ቯߦᚯߔ
Adjusting for Mirror (SSC)
Other Brand AR/LM comm.
End
7.8 Resetting the setup data
1.
2.
3.
4.
Enter the Information / Adjustment screen. (See 7.1.)
Press [Reset the Setup Data].
The Reset the Setup Data window appears.
Pressing [Yes] return the value to the setup data.
* Both the AR and LM data are also cleared.
5. Select the chart. (See 7.3.)
7-4
MRT10*RDA001A/E
7.9 Communication setting with other brand AR/LM
1. Enter the Information / Adjustment mode. (See 7.1.)
2. Press [Other Brand AR/LM Comm.].
3. The Other Brand AR/LM Comm. screen
appears.
4. Press the number of the Connected AR and Connected LM to select the setting.
1) AR
a. NIDEK:
00
Information / Adjustment
b. TOPCON RM-A, KR :
01
c. Humphery 500 to 595:
02
d. Humphery 599:
03
Status Information
Chart Selection
e. Canon R-20, R-22:
04
Other Brand AR/LM comm.
f. Canon RK-3:
05
㧹㧮ೋᦼࡄ࡞ࠬ
Adjusting for Chart/Mask
00
Connected AR
g. Nikon NRK-800:
06
00
Connected LM
Adjusting for Mirror (SSC)
Ꮏ႐಴⩄ߩ⸳ቯߦᚯߔ
End
h. Rodenstock CX-520:
07
i. Nikon Retinomax:
08
Other Brand AR/LM comm.
2) LM
a. NIDEK:
00
b. Humphery 350:
01
End
* For the latest information of the compatible models, it is necessary to check the T.B.
7.10 Adjusting the clock
Adjust Clock
1. Press [Others] on the Main Menu screen, and
press [Adjust Clock] on the Others screen.
2005
2. Select the item to be changed, and set the
clock on the touch panel, and press [Enter].
3. Press [End] or [Menu] to write the clock
setting and return to the normal measurement
screen.
/
10
/
10
:
10
15
End
Adjust Clock
7
2005
4
1
0
8
9
/
10
2
3
5
10
←
6
:
Clear
Cancel
/
15
Enter
10
End
7-5
MRT10*RDA001A/E
7.11 Updating the software
1. Write the updating program file in the compact flash memory card with the PC.
2. Open the CF cover (34085-M412) while the
power of the RT-5100 CB is off.
3. Turn up the ejection lever and push it with
tweezers and such to eject the compact flash
memory card.
4. Insert the compact flash memory card in
which the program is written.
5. Turn on the power while pressing the Shift
key of the control box.
6. A list of the updating program files appears
File name
Example
on the display of the control box. The files Device
CB RT10CB_vvvvv.mot RT10CB_100.mot
stored in the compact flash memory card in
MB RT10MB_vvvvv.mot RT10MB_101T2.mot
Motorola S format (*.mot) are displayed in
RB RT10RB_vvvvv.mot RT10RB_125S.mot
a list.
7. Select the file name to be updated with the
up-arrow / down-arrow button on the screen
and press [SELECT].
8. Press [OK] in a confirmation dialog to start updating.
9. The display returns to the file list screen after the updating has been completed.
* Perform the updating of each device (MB/CB/RB) as necessary.
* The data will be reset when updating the CB. Start updating the other device continuously
from step 3.
10.Turn off the power after the updating has been completed.
11.Eject the compact flash memory card in which the updating program is written.
12.Insert the original compact flash memory card, and turn down the ejection lever to close the
FC cover (34085-M412).
7.12 Clearing the AR/LM data
1. Press the IN key and set the data No. to “0” by turning the dial.
2. Press the Clear key to delete all the data.
7-6
MRT10*RDA001A/E
7.13 Touch-screen panel calibration
1. Press the right side switch while pressing
the Shift key of the control box to display
the Brightness Control window.
2. Press the dial switch (in the center of the
Touch Panel Calibration
dial) to display the Touch Panel Calibration
screen.
3. Press the red square in the upper-left corner
Red‫ع‬
of the screen with the touch-screen pen.
* Pressing here changes the color of the
square to blue.
4. Press the red square in the upper-right
corner of the screen with the touch-screen
pen
5. Press the red square in the lower-left corner
of the screen with the touch-screen pen.
6. Press the red square in the lower-right
corner of the screen with the touch-screen
pen.
* When the four squares at each corner of the screen are pressed, the Completed the Touch
Panel Calibration message appears and the screen returns to the normal measurement
screen.
7-7
MRT10*RDA001A/E
7-8
MRT10*RDA001A/E
§8 REFERENCES
8.1 Wiring diagram
8-1
MRT10*RDA001A/E
8.2 Connector cables
34085-EA01
34085-EA02
34085-EA04
34085-EA11
8-2
MRT10*RDA001A/E
34085-EA21
8-3
MRT10*RDA001A/E
34085-E022
8-4
MRT10*RDA001A/E
8.3 Error messages
Message
Error01: Communication Error
CB-RB
Error11: Communication Error
CB-RB
No appointment data!!
No data!!
Chart does'nt work.
Setup data is initialized.
CF card -- Read Error!!
CF card -- Write Error!!
CF card -- File Error!!
CF card -- File not found!!
CF card -- Card not found!!
Contents
Data communication error between CB and MB
MB does not work
Failure in the communication cable between CB and MB
Data communication error between CB and MB
MB does not work
Failure in the communication cable between CB and MB
No specified data of AR and LM
The No. of the specified data does not exist.
AR and LM to be input is not connected.
Failure in the connecting cable
The data to be input in IC card and such does not exist.
Changing chart is attempted while the chart is moving.
Chart is not connected.
Failure in the connecting cable
Failure in the communication cable between CB and RB
The data stored in a battery on the CB was deleted or changed from
any cause (failure in battery and such).
The setup data is reset by pressing Shift and Menu buttons on the
Menu screen.
Test program cannot be input.
The CF is not inserted or there is no data in the CF.
Failure in the connector of the CF
Test program cannot be output.
The CF is inserted.
Insufficient space in the CF
Failure in the connector of the CF
The specified image file in the CF breaks.
The specified image file in the CF does not exist.
The CF is not inserted (when reading the image file).
8-5
MRT10*RDA001A/E
8.4 Parameters
Page
1
2
3
4
5
Item
SPH step
CYL mode
AXIS step
SPH step (Shift)
CYL step (Shift)
AXIS step (Shift)
AXIS auto step
Cross cylinder (XC) test
XC mode S.E fix
Cyl mode S.E fix
Prism display format
Prism (0.1△Repeat)
Input prism from LM
Fog for binocular balance
Preset VA
Preset ADD
SPH Far → Near
(-) ADD
Working distance (WD)
Convergence/Divergence test
Print CL data
Print TL data
Clear after print
Printer
Print format
Date format for print
Print list
Operating timer
Program A
Program B
Adjust ADD Subj → Final
Preset power of Subj 1
Preset power of Subj 2
Intelligent XC
Dial switch
Lens for Retino
Auto lamp off
Beep sound
Chart link
Memory function
AR port
LM port
Input sequence from PC
Daisy chain communication
Default
Set contents
0.25D
0.12D / 0.25D
-/+
5
1/5
1.00D
1.00D / 2.00D / 3.00D
1.00D
1.00D / 2.00D / 3.00D
1→5/5→1
1→5/5→1 / 1→5/5→15
0.00D
0.00D to 2.00D (0.25 increments)
Auto
Auto / ±0.25D / ±0.50D
Yes
Yes / No
No
Yes / No
X/Y
X/Y / rθ
0.7 sec
1.0 sec / 0.7 sec
No
Yes / No
Yes
Yes / No
H.line
1 letter / H.line / No
Yes
Yes / No
SPH+ADD
SPH / SPH+ADD
No
Yes / No
40 cm
35cm to 70cm (5cm increments)
Yes
Yes / No
No
Yes / No
No
Yes / No
Yes
Yes / No
Stardard
Standard / Canon / HP / Off
All data
All data / w/o AR / Unaided / Subj / Final
mm/dd/yyy
mm/dd/yyy dd/mm/yyy yyy/mm/dd
Yes
Yes / No
Yes
Yes / No
Fix
Fix / User
Fix
Fix / User
Yes
Yes / No
AR
AR / LM
All data
All data / CYL=0 / Clear
Yes
Yes / No
S→C→A S→C→A / S→C→A→VA / S→A→C / S→A→C→VA
+1.50D
+1.50 D / +2.00D
15 min
Off / 5 min / 15 min / 30 min
High
High / Low / Off
Yes
Yes / No
Yes
Yes / Memory box / No
AR
AR / ARK / RKT
LM
LM / ARK / RKT / AR
Hold
Hold / Pass
No
No / Server / Client a (to 4)
8-6