Download PCM-R500

PCM-R500
SERVICE MANUAL
US Model
Canadian Model
AEP Model
Model Name Using Similar Mechanism
DTC-A8
Tape Transport Mechanism Type
DATM-55
SPECIFICATIONS
– Continued on next page –
DIGITAL AUDIO TAPE DECK
MICROFILM
MODEL IDENTIFICATION
– Model Number label (Printed in Back Panel) –
MODEL NO. PCM-R500
DIGITAL AUDIO TAPE DECK
US, Canadian model : AC 120 V 60 Hz 34 W
AEP Model
: AC 230 V ⁄ 50/60Hz 34 W
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer.
Discard used batteries according to the manufacturer’s instructions.
ADVARSEL!
Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering.
Udskiftning må kun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandøren.
ADVARSEL
Eksplosjonsfare ved feilaktig skifte av batteri.
Benytt samme batteritype eller en tilsvarende type
anbefalt av apparatfabrikanten.
Brukte batterier kasseres i henhold til fabrikantens
instruksjoner.
VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en ekvivalent typ som
rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens instruktion.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚ C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering .
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu.
Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin.
Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
–2–
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microampers). Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The “limit” indication is 0.75
V, so analog meters must have an accurate low-voltage scale.
The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2 V AC range are suitable. (See Fig. A)
To Exposed Metal
Parts on Set
0.15 µF
1.5 k Ω
TABLE OF CONTENTS
1.
GENERAL ..................................................................... 4
2.
DISASSEMBLY ............................................................ 15
3.
ADJUSTMENTS .......................................................... 19
4.
DIAGRAMS
4-1.
4-2.
4-3.
4-4.
4-5.
4-6.
4-7.
4-8.
4-9.
4-10.
4-11.
4-12.
Block Diagrams .................................................................
Printed Wiring Board – RF Section – ................................
Schematic Diagram – RF Section – ...................................
Printed Wiring Boards – MD Section – .............................
Schematic Diagram – MD Section – .................................
Printed Wiring Boards – DIGITAL Section – ...................
Schematic Diagram – DIGITAL Section – ........................
Schematic Diagram – AUDIO Section – ...........................
Printed Wiring Boards – AUDIO Section – .......................
Printed Wiring Boards – DISPLAY Section – ...................
Schematic Diagram – DISPLAY Section – .......................
IC Pin Function Description ..............................................
5.
EXPLODED VIEWS ................................................... 83
6.
ELECTRICAL PARTS LIST .................................... 91
26
33
35
38
41
45
49
53
57
61
65
72
AC
voltmeter
(0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY-RELATED COMPONENT WARNING!!
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED
LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE !
SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE
DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ
DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES
NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
–3–
This section is extracted
from instruction manual.
SECTION 1
GENERAL
–4–
–5–
–6–
–7–
–8–
–9–
– 10 –
– 11 –
– 12 –
– 13 –
– 14 –
SECTION 2
DISASSEMBLY
HOLDER ASS’Y
Note: Follow the disassembly procedure in the numerical order given.
CASE
3 nylon washer
1 screw (step)
2 case
1 four screws
(case)(M3 × 10)
4 screw
(BVTT3 × 6)
5 Side plate (R) ass’y
1 five screws
(case) (M3 × 10)
8 holder ass’y
2 two screws
(B2.6 × 4)
7 function plate ass’y
6 two screws
(B2 × 4)
MECHANISM DECK BLOCK
1 Open the lid.
6 two screws
(PTPWH 3 × 6)
6 two screws
(PTPWH 3 × 6)
CASSETTE COMPARTMENT MOTOR ASS’Y
9 cassette compertment
motor ass’y
4 three connectors
(CN506-508)
8 two screws
(P2.6 × 3)
0 screw
(B2.6 × 4)
5 flat wire
(CN504)
6 screw
(B1.7 × 3)
7 slider
ass’y
1 capstan belt
!¡ chassis (L)
0 screw
(B2.6 × 4)
5 driving gear
2 two claws
2 screw (B1.7 × 3)
3 lid
2 two claws
– 15 –
7 Remove the mechanism
deck block to direction
of the arrow.
4 screw (B1.7 × 3)
3 pulley
– 16 –
DRUM
CAPSTAN MOTOR
3 two screws
(B2 × 3)
3 two screws
(B2 × 3)
2 capstan motor
2 connector
(CN52)
1 flexible board (CN7)
4 drum
1 three screws
(P1.7 × 4)
DRUM DRIVE BOARD, REEL MOTOR
1 two screws
(B2 × 3)
1 two screws
(B2 × 3)
2 DRUM DRIVE board
4 bracket
5 two screws
(B2 × 3)
3 screw
(B2 × 3)
6 reel motor
– 17 –
– 18 –
SECTION 3
ADJUSTMENTS
PRECAUTION
1. The adjustments are performed in the sequence that they are
described.
2. The required test tapes are:
TY-7111 (8-909-812-00) ................................. Level
TY-7252 (8-909-822-00) ................................. Tracking
TY-7551 (8-909-814-00) ................................. Function
TY-30B (8-892-358-00) ................................... Blank
The required torque meter is:
TW-7131 (8-909-708-71) ................................ FWD
3. Switch and Control Settings
REMOTE switch
: OFF
REC MODE switch
: 48k (STANDARD)
REC LEVEL control
: Minimum
PHONE LEVEL control : Minimum
4. Preparation of End Sensor Cassette
(1) Push the slider locks of a cassette tape and slide the slider in
the direction of the arrow.
6. When adjusting tape pass and each guide, as shown below, it is
a good practice to remove the holder assy and use the DAT cassette holder (J-8000-002-A). This facilitates adjustment work.
• When removing and installing the holder assy, turn the pulley
counterclockwise and set loading OUT condition for easy removal and installation.
• When adjusting, turn the pulley clockwise and turn on the
CASSETTE TABLE IN switch (S2) to set loading IN condition. Then, set the test tape.
8. After adjustment is completed, perform the following checks to
verify the tape speed.
(1) Check that with the REC MODE switch set to STANDARD
48k, tape is normally recorded and played back. (×1)
(2) Check that with the REC MODE switch set to LONG, tape
is normally recorded and played back. (×0.5)
(3) Check that in performing the CUE (” + )) or REVIEW
(” + 0) operation, “kyur kyur” sound is heard. (×3, ×8)
(4) Check that after performing the FF ()) or REW (0)
operation, the time display is appropriate. (×16)
(5) Check that the AMS (+, =) operation is normal.
Adjustment Location: mechanism deck block
1 BVTT 3 × 8
5 Nylon washer
6 Step screw
hub hole
T1 guide
7 Cassette
holder assy
slider lock
slider
3 Cassette 4 Push down the holder
in the direction
spring
T2 guide
S1 guide
2 BVTP 3 × 6
7. Test Mode
• To enter the test mode, short between TP (MAIN-TEST) and
the GND on the DIGITAL board, then turn on the power. The
meter scale within the fluorescent indicator tube (FL701) will
flash.
Press the OPEN/CLOSE 6 key and set the test tape. (The
specified tape should be used for each adjustment.)
hub hole
slider lock
(2) Open the cassette lid and cut tape.
cassette lid
cut tape
slider
F guide
S2 guide
Test Mode (Short between TP (MAIN-TEST) and GND)
1 Have “DPG” display lit in the fluorescent indicator tube.
(Press the AMS + key.)
• S2, T2 and F Guide Adjustments
• End Sensor Adjustment
• Tape Pass Fine Adjustment (×1.5FWD mode)
• DPG Adjustment
2 Have “TR” display lit in the fluorescent indicator tube.
(Press the ” key.)
• FWD Torque Adjustment
• FWD Back Tension
(Torque measurement mode)
Adjustment
• To release the test mode, remove the short between TP (MAINTEST) and GND. After necessary adjustment is completed,
be sure to release the test mode.
tape
(3) Turn the hubs to take-up tape (for both T and S sides).
The end sensor cassette tape for end sensor adjustment is
now prepared.
5. Take care never to turn RV1 and RV2 within the RF AMP board
of the cassette compartment section.
– 19 –
– 20 –
3-1. MECHANICAL ADJUSTMENTS
When replacing any drum related parts, after S2, T2 and F guide
adjustments have been made, tape pass fine adjustment (×1.5FWD
mode) in Electrical adjustment should be performed.
S2, T2 and F Guide Adjustments
Adjustment Method:
1. Enter the Test Mode 1 (see page 19.) and set the test tape TY7252 (8-909-822-00).
2. Set the REC MODE switch to STANDARD 48k and press the
AMS + key.
While in FWD mode, check that there is no curl on the upper
and lower flanges of the S2, T2 and F guides.
If any curl is present, put the S2, T2 and F guide of concern
back in the high position and adjust by adjusting the direction
of tightening.
* What is curl?
Distortion that occurs on
tape during FWD operation.
FWD Back Tension Adjustment
Adjustment Method:
1. Enter the Test Mode 2 (Torque Measurement Mode) (see page
19.) and set the torque meter TW-7131 (8-909-708-71).
2. Press the PLAY (”) key.
3. Press the AMS + key or = key and adjust so that the back
tension (S side) is within the range of 8.5 ± 0.5 g•cm.
4. When the torque meter is circulating around, check the indicated value.
5. Verify that the maximum value is less than 19.5 g•cm.
REV Torque Check and REV Back Tension Check
Check Method:
1. After FWD torque adjustment and FWD back tension adjustment are completed, press the PLAY (”) key again and set REV
(“) mode.
2. Check that the REV torque value is within the range of 13.5 to
17.5 g•cm and that the REV back tension value is within the
range of 7.5 to 11.5 g•cm.
Curl
3-2. ELECTRICAL ADJUSTMENTS
End Sensor Adjustment
When removing the holder assy and when replacing the mechanism
deck block, this adjustment should be performed.
Adjustment Method:
1. Connect the CH-1 terminal of an oscilloscope to TP (S-END)
and the CH-2 terminal to TP (T-END) on the DIGITAL board.
2. Enter the Test Mode 1 (see page 19.) and set the end sensor
cassette tape (see page 19.)
3. Set the STOP (p) mode.
4. Adjust RV502 (S-END) and RV501 (T-END) on the DIGITAL
board so that the respective peak to peak values of the waveforms on the oscilloscope are 1.2 Vp-p.
Tape Pass Fine Adjustment (×1.5FWD Mode)
When replacing any drum related parts, be sure to perform this adjustment.
Adjustment Method:
1. Connect the CH-1 terminal of an oscilloscope to TP (RF) and
the CH-2 terminal to TP (SWP) on the DIGITAL board.
2. Enter the Test Mode 1 (see page 19.) and set the test tape TY7252 (8-909-822-00).
3. Press the AMS (+) key.
Role of each switch in test mode.
OFFSET
–
0
WIRED
+
OFF WIRELESS
ATF : ON
STANDARD
48k
1.2Vp-p
REMOTE
Adjustment Location: See page 23.
FWD Torque Adjustment
Adjustment Method:
1. Enter the Test Mode 2 (Torque Measurement Mode) (see page
19.) and set the torque meter TW-7131 (8-909-708-71).
2. Press the PLAY (”) key.
3. Press the ) key or 0 key and adjust so that the FWD torque
value (T side take-up torque) is within the range of 11 to 13
g•cm.
4. When the torque meter is circulating around, check the indicated value.
ATF : OFF
LONG
44.1k
REC MODE
4. Put the REC MODE switch to the LONG (ATF: OFF) position
and put the REMOTE switch to either the WIRED or WIRELESS position (OFFSET: – or +), fine adjust both the S1 guide
and T1 guide so that the RF signal waveform of the oscilloscope repeatedly contracts and expands in vertical directions as
it has the same shape.
* Adjust the direction of tightening to complete this adjustment.
If there is curl on any of the upper and lower flanges of the
S2, T2 and F guides, adjust the guide of concern.
– 21 –
5. Put the REC MODE switch to the STANDARD 48k (ATF: ON)
position and put the REMOTE switch to either the WIRED or
WIRELESS position (OFFSET: – or +), then check the RF signal waveform.
Check that there is a difference of 650 ± 15 µsec between the
oscilloscope’s SWP signal and the RF signal.
RF
4 A or less
5
NG
SWP
650±15 µsec
A
Adjustment Location: See page 23.
4 A’ or less
5
NG A'
OK
6. Put the REC MODE switch to the STANDARD 48k (AFT: ON)
position and put the REMOTE switch to the OFF position (OFFSET: 0), then check the RF signal waveform.
(1) Verify that the peak value (B) of the RF signal waveform is
60mV or more.
(2) Verify that the flat position of the RF signal waveform has
undershoots of 10% or less.
B or less
10
B or less
10
B
7. If any of the specified values are not satisfied, repeat items 3 to
6.
CHECK AND REPLACEMENT FOR DATE FNCTION
Clock IC Back-up Check
• When replacing the lithium battery (BATT501) or replacing any
of the clock IC (IC518) and peripheral parts, the clock will be
reset.
(The DATE display will be [‘-- -- --] [--h--m--s] even when the
[PRESENT] button is pushed.)
Perform the back-up check by the following procedure.
(1) Connect a DC voltmeter between the DIGITAL board’s TP
(BATT+) as (+) side on the TP (BATT–) as (–) side.
(2) With the POWER switch of the set OFF, check that the voltage (1) is less than +20 mV.
(If the measured value is more than +20 mV, inspect the IC518
and peripheral parts and replace as needed.)
(3) With the POWER switch of the set ON, check that the voltage (1) is less than 0 mV (minus indication), (If plus indication, inspect the D510 and peripheral parts and replace as
needed.)
(4) When these voltages are normal, set the clock to the current
date and time according to the instruction manual.
(year/month/day/day of week/hours/minutes/seconds)*
(5) After the clock is set in item (4), turn off the POWER switch
once and in several seconds, turn on the power again and
make sure that the clock is operating.
Adjustment Location: See page 23.
Adjustment Location: See page 20.
DPG Adjustment
When replacing any drum related parts, be sure to perform this adjustment.
Adjustment Method:
1. Connect the CH-1 terminal of an oscilloscope to TP (RF) and
the CH-2 terminal to TP (SWP) on the DIGITAL board.
2. Enter the Test Mode 1 (see page 19.) and set the test tape TY7252 (8-909-822-00).
3. Put the REC MODE switch to the STANDARD 48k (ATF: ON)
position and put the REMOTE switch to the OFF position (OFFSET: 0).
4. Press the AMS (+) key.
5. Press the PLAY (”) key.
6. “DPG OK” is displayed in the fluorescent indicator tube.
– 22 –
Replacement of Back-up Battery
The back-up battery for clock is designed to serve for more than
seven years under normal service conditions (room temperature and
ordinary humidity).
When replacing the battery, take note of the following:
• Perform the above “Clock IC Back-up Check” and remedy the
cause of battery consumption.
• The open voltage of the battery as removed is 3.0 V or more when
it is new. If this voltage is 2.0 V or less, then battery is fully consumed and needs to be replaced.
• After the battery is replaced, perform the “Clock IC Back-up
Check” again and set the clock.
• The coin type lithium battery (CR2032) is used for replacement.
Adjustment and Check Locations :
DIGITAL board – component side –
* For description of the clock setting, see page 5.
TP
(RF)
END SENSOR ADJ
(S-END)
RV502
TP
(S-END)
(T-END)
RV501
TP
(T-END)
TP
(BATT+)
TP
MAIN–
TEST
– 23 –
TP
(SWP)
TP
(BATT–)
– 24 –
SECTION 4
DIAGRAMS
• Circuit Boards Location
Note: AUDIO board and DIGITAL board are supplyed as MAIN board.
REG BOARD
REMOTE BOARD
DIGITAL OUT BOARD
PRIMARY BOARD
DIGITAL BOARD
DIGITAL IN BOARD
UNBAL BOARD
ANA OUT BOARD
REM SW BOARD
ANA IN BOARD
HP BOARD
AUDIO BOARD
DISPLAY BOARD
INPUT SW BOARD
SHUTTLE BOARD
REC BOARD
DRUM DRIVE BOARD
SW BOARD
MOTOR BOARD
RF BOARD
S END BOARD
LOADING MOTOR BOARD
CAPSTAN MOTOR U-17A
(M902)
THICK BOARD
LOAD SW BOARD
T END BOARD
REEL MOTOR U-2A
(M903)
REC EN BOARD
– 25 –
4-1.
BLOCK DIAGRAMS
(1) Power Section
-33V
FL701
F1, F2
D503
-33V REG
Q502, 503
T901
E
D502
FPM KICK 1
FPM ON 100
FWD PM
DRIVE
Q504, 505
Q509, 511
D505
SERVO
PROCESS
IC502 (3/3)
BPM KICK 4
BPM ON 3
PM902 +6V
FWD
PLUNGER
PM901
BRAKE
PLUNGER
+2V REG
Q501, 901
+5V
+5V REG
IC901
+12V
IL901
~AC IN
N
D501
+12V REG
IC319
D301-304
+12V
+12V REG
IC301
-12V
-12V REG
IC302
-12V
-12V REG
IC320
+12V
+5V (A)
+5V REG
IC316
+5V (B)
+5V REG
IC317
+5V (C)
+5V REG
IC318
+5V (D)
+5V REG
IC305
-12V
-5V
S901
POWER
L
+2V
D506
BRAKE PM
DRIVE
Q506-508
Q510
+6V REG
IC902
-5V REG
IC306
– 26 –
E
PCM-R500
(2) Digital Audio Section
T801
2
IC508
1 (1/4,4/4)
COAXIAL
IN
SIGNAL SELECT
IC511
NORMALIZER
IC508 (2/4)
IC509 (1/2)
8
RS-422 RECEIVER
IC801 (1/2)
52
13
J501-1
45
PHASE
CONTROL
IC513 (1/6)
COAXIAL
RX VCO
IC513 (5/6, 4/6)
D513, Q520
48
RX
ADDI
DIGITAL
OUT
RX
PLL
PDO
DADT
PLCO
ADDN
AES/EBU
VCOEN
2
1
SYSTEM CONTROL
SECTION
9
76
AIN
10
15 2 14
2Q
LRO1 71
10
3
54
6
J501-2
TX
DADO
DIGITAL
IN
D F/F
IC512
9 CLK
78
5 4 13
4
64 XT2I
66 XT3O
IC510 (2/4)
F128
BCK
LRCK
XT1I
X501
24.576MHz
RV2
A REC
PCM
67 XT3I
RV1
B REC
PCM
39
F128
BCK
LRCK
58
75
72
14
X502
18.816MHz
DADO
XT1O 13
XRST 16
40
PIPC 46
REC A
REC/PB
HEAD
A
13
80
DAT DSP
IC503
IC510 (1/4)
3
2
T501
41 PIPC
SWP 47
39 SWP
MUTA 47
UNLK 31
FSEN 68
Q522
33
42 REPB
REC/PB 45
BCK
LRCK
DADO
XRST
XLM
B
MUTE A
UNLK
FSEN
SYSTEM
CONTROL
SECTION
C
SYSTEM
CONTROL
SECTION
REC B
27
43
44
REC OCA
REDT
Q524
DAT
DSP
PB A
34
PCM
EQ
26
GCA
PILOT
OCA
PB RF
BUFFER
Q521
37
RFDT
14
ATSY
DREF
AGC
BUFFER
IC521 (1/2)
A0-A14
XOE
XWE
RF AMP
IC1
11
1, 2, 4-8
93-100
84-89
91, 92
10 9
19 21
1-10, 21
23-26
11-13
15-19
22 27
A0-A14
D0-D7
XOE
XWE
PB B
57
38
30
29
23
24
25
26
96
97
70
98
55
54
53
52
40
XREC/PB 16
XANA/DIG 15
EXSY-MUT
XMST-SEL
MUT-MONIT
MST-MUTE
SR-CK
SR-DTO
SR-DTI
XSBSY
XRST
SBM-ON
XADLD
AUSC
AUSO
FS48
FS44
XADINT
XDAINT
XDALD
95 REC-DIS
43 EXTAL
SRAM
IC504
SYSTEM
CONTROL
IC501 (1/2)
9.4MHz
XLM
FSEN
SBM
ADLD
AUSC
AUSO
FS48
FS44
ADINT
DAINT
DALD
1
11
8
7
28
29
93
94
12
XBAL
XBAL 2
1/2
9 DIVIDER 11
IC519
18.8MHz
+5V
– 27 –
SWP
PBDT
AGC PWM
ATF
73 91 72
48 40
43 77
EXTAL
MSTCLK
79
78
80
66
XSBSY
XRST
6
ATF-S2
ATF-S2
DREF
REC/PB
HEAD
B
1
EXSN
XCS
MUTM
MUTE
EXCK
SDSI
SDSO
SBSY
D0-D7
COAXIAL
OUT
12
77
7 2 15
RS-422 RECEIVER
IC801 (1/2)
9
5
PEV
DIGITAL
IN/OUT
AES/EBU OUT
T802
A
11
ST
IC513 (6/6)
S501
AES/EBU
-COAXIAL
J802
ADDT
79
RESET
IC516
7
SERVO PROCESS
IC502 (1/3)
– 28 –
D
ANALOG
AUDIO
SECTION
ANALOG AUDIO SECTION
+
–
B
A
11
1Q
4Q
12
3
1D
4D
2
1
2D
J801
DIGITAL
IN/OUT
AES/EBU IN
PCM-R500
(3) Analog Audio Section
RV301
REC LEVEL
1
4
54
26
56
27
41 40
42 45
SBM
FSEN
Q303
LINE IN
3
1
CLOCK
BUFFER
IC313 (3/6)
6
ADLD
XSFEN
7
F128
ADINT
RY305
J307-2
R-CH
CH-1 (R)
AIN
50
SBM
22
LATCH
2
DLO
10
RELAY
DRIVE
Q316
CLOCK
BUFFER
IC313 (4/6)
9
BCK
2
XBAL
11
D
DIGITAL AUDIO SECTION
CLOCK
BUFFER
IC313 (5/6)
15
PHASE
COMPARATOR
IC315
S 7
8 R
PD
3
12
13
6
PRESCALER
IC312
10
XFSEN
Signal path
PHASE
CONTROL
Q304-306
CLOCK
BUFFER
IC313 (1/6)
3
LRCK
AUSO
AUSC
CLOCK
14
BUFFER
IC313 (6/6)
X301
24.576MHz
7
IC325
(2/2)
MAIN VCO
Q307, 308
D308
: PB
: REC
3
XFSEN
1
2
9
IC311
(2/6)
10
10
1/2
DIVIDER
IC309 (2/2)
3
11
IC325
(1/2)
5
1/2
DIVIDER
IC309 (2/2)
3
4
5
6
11
8
9
12
13
IC301 (1/6)
IC301 (3/6)
IC301 (5/6)
IC301 (2/6)
IC301 (4/6)
IC301 (6/6)
FS48
FS44
3
4
4
6
5
2
1
FSEN
X302
22.5792MHz
DADO
DALD
DAINT
LINE AMP
IC103 (2/2)
5
7
LINE AMP
IC103 (1/2)
LINE AMP
IC104 (1/2)
3
1
6
7
2
48
49
38
47
INVOI
XBCK
128FSO
DADO
DIGITAL
FILTER
DIGITAL FILTER/
D/A CONVERTER
IC314
XIN
XINT
39 45 35 34 36 37
XLRCK
512FSO
SHIFT
ATT
LATCH
RV102
LEVEL
CH-1 (L)
10
L1 (+)
63
L2 (+)
2
D/A
CONVERTER
21 18
L1 (-)
61
L2 (-)
4
R1 (-)
R2 (-)
40
XFSEN
INVI
1
FSEN
MIX AMP
IC101
IC102 (2/2)
HP AMP
IC321 (1/2)
3
1
Q102
RY301
RELAY
DRIVE
Q312
RV302-1
PHONE
LEVEL
MUTE
DRIVE
Q309-311
J306-1
CH-1 (L)
LINE AMP
IC104 (2/2)
ANALOG
(LINE) OUT
R-CH
R-CH
LINE AMP
IC102 (1/2)
3
1
3
2
1
R-CH
J301
PHONES
3
J306-2
CH-2 (R)
J307-3
CH-1 (L)
LINE OUT
R-CH
CH-2 (R)
J307-4
23 16
XLM
R-CH
– 29 –
– 30 –
TO DOGITAL AUDIO SECTION
J307-1
ARI
-1
LINE AMP
IC326 (1/2)
1
3
CH-1 (L)
21
SBM DIGITAL FILTER
IC308
SBM
DIGITAL
FILTER
MODE
R-CH
R-CH
ALI
SHIFT
R-CH
3
21
MCLK
2
ADR 21
R1 (+)
R2 (+)
J305-2
CH-1 (R)
26 AINR+
25 AINR-
SYNC
RV101
LEVEL
CH-1 (L)
ANALOG
(LINE) IN
A/D CONVERTER
IC307
LINE AMP
IC303,
IC304
LRCK
1
FCLK
3
2
BCK
3
1
+
–
INIT
1
LINE AMP
IC324 (1/2)
ICLK
CH-1 (L)
2
2
APD
LINE AMP
IC323 (1/2)
J305-1
PCM-R500
(4) System Control Section
7
BUFFER
IC522
(1/2)
5
83
77 D PWM
2
FG
14
MR
16
7
DFG
AMP
3
71 D PG
S901-1
+5V
(REC PROOF)
CFG
AMP
REC EN 26
CAS IN 25
70 D FG
10
2G-11G
8 - 17
FL DISPLAY
DRIVE
Q701-703
JOG
SHUTTLE
S736
–30V
69 C FG
70 69 68
34 - 57
S0-S23
22 - 29
AD0-AD7
71
58 - 67
T3-T12
14 MMUT
16 - 19
B1-B4
20, 21
A.B
REMOCON
SELECTOR
IC704
J804
(REMOTE-2 IN)
XRST
EXTAL
XTAL
5
74 75 76 77 11 12 13
30
31
32
RD
CS
D3
12
REM SEL 15
X701
4.19MHz
15 14
9
11 12 13
7
6
A1
D0
D1
CS
RD
LED DATA LATCH
IC703
7
LPF
IC520
(2/2)
Q4
Q3
RST
AUDIO METER
IC702
15 12 10
7
1
Q6
67 T FG
+5V
5
XRST 4
XRST
LRCK 3
LRCK
BCK 2
BCK
DATA 1
C
REAL TIME
CLOCK
IC518
DIGITAL AUDIO
SECTION
DATAO
XLM
+5V
5
BATT501
3V
D510
VDD 8
SCLK
CE
14 13
WR
6
D3
4
D2
3
A0
11
D5
9
D6
81 T PWM
D3
3
D2
LPF
IC520
(1/2)
D1
1
FG
S-REEL
MOTOR DRIVE
Q515-517
REMOTE
CONTROL
RECEIVER
IC705
60 T END
99 XTLOCK
M
1
DATA
M
4
D4
T-REEL
MOTOR DRIVE
Q512-514
6
SERVO PROCESS
IC502 (2/3)
RV501
T-END
SENSOR
+5V
WR
47 S LED ON
10
D2
LED
DRIVE
Q518
9
METER
D1
7 ACK
79 REQ
6
FL DISPLAY DRIVE
IC701
D0
2 CAP RVS
Q951
T-END
SENSOR
RMC 2
8 SC
10 SO
9 SI
84 C PWM
A2
5
A1
BUFFER
IC522
(2/2)
LED CLK
7
CLK
CAPSTAN
MOTOR DRIVE
IC1 (1/2), Q3
+5V
D511
D512
7
6
X503
32.768KHz
2 3 4
82 S PWM
LED DRIVE
Q704-707
D701-704
68 S FG
FG
J803
20 21 22
60 S END
+5V
S903
(LOAD)
S902
(UNLOAD)
M
2
7
LOADING
MOTOR
DRIVE
IC2
+5V
M1
CASSETTE
COMPARATMENT
MOTOR
M
2
7
CASSECOM
MOTOR
DRIVE
IC523
50 DM DO
SCK 55
Q807
51 DM CK
XMECA-BSY 44
XMECA-REQ 52
DIGITAL
OUDIO
SECTION
A
5
31
9
30
12
1
2
IC515
(1/4)
5
6
IC514
(2/4)
4
2
3
IC514
(1/4)
– 31 –
XROM-CK 19
XROM-DT 20
6
5
13
IC515
(4/4)
11
10
13
IC514
(4/4)
12
1
INVERTER
Q801-806
PRL REM 66
VCOEN
3
17 CAS M OUT
18 CAS M IN
6
8
9
8
11
10
IC515
(3/4)
8
9
IC514
(3/4)
FSEN
EEPROM
IC517
UNLK
MUTEA
– 32 –
B
DIGITAL
OUDIO
SECTION
REMOCON
INTERFACE
IC802
1
4
2
59 XMECA-BSY
46 XMECA-REQ
27 CAS LCK
28 CAS OUT
7
3
SYSTEM CONTROL
IC501 (2/2)
49 DM DI
S11
CASSETTE
TABLE IN
S12
CASSETTE
TABLE OUT
6
3
30 LOAD SW
29 UNLD SW
MECHA
DTI 53
DTO 54
15 LM EJECT
16 LM LOAD
6
3
REMOTE
Q808
LED2 76
LED1 75
RV502
S-END
SENSOR
+5V
M901
LOADING
MOTOR
44 XDISP-REQ
48 XDISP-ACK
FS32
Q950
S-END
SENSOR
47 S LED ON
VCOEN
LED
DRIVE
Q519
RTC-DT
RTC-SC
RTC-CE
+5V
XLM
S-REEL
MOTOR
5 6 7
POWER TRANSFORMER
T901
1
M
T-REEL
MOTOR
18-20, 24
39-58
FUNCTION
SWITCH
MATRIX
S701-720, 723-730
S732-735
S901-2
(CASSETTE IN)
AMP
IC3
CAPSTAN
MOTOR
P24-P1
1G
12G
13G
DPG
AMP
T0
T1
T2
4
PG
Q5
DRUM
MOTOR
E
F1 1
F1 2
F2 61
F2 62
FLUORESCENT
INDICATOR TUBE
FL701
5 DRM ON
VFDP
DRUM
MOTOR DRIVE
IC1 (2/2), Q1, 2
M
• IC Block Diagrams
1
2
3
4
LIM VCC 5
ENV OUT 6
A R PCM
SAG TC
A HA OUT
48 47 46 45
LIM OUT
LIM GND
MOD1 IN
MOD2 IN
44 43 42 41 40 39 38
37
REDT IN
PB VCC
B R PLT
A R PLT
B R PCM
PIPC IN
RE/PB IN
CXA1364R (RF AMP board)
NRR HLF
SWP IN
36 ALPC
35 A PC
A
PB
AMP
REC OCA
LOGIC
34 A HA IN
33 A RA OUT
PB LIMIT
RF
ENVELOPE
DET
ENV COMP 7
ENV PEAK 8
A
REC
AMP
32 REC VCC
31 HA VCC
SWITCH
30 REC BIAS
LIM IN 9
EQ OUT 10
B
REC
AMP
PCM EQ
29 REC GND
28 HA GND
PILOT
ENVELOPE
DET
27 B RA OUT
B PB
AMP
25 B PC
PILOT
FILTER
EQ OUT
EQ HIGH
EQ LOW
V REG
CAP FG
OUT 1
CAP FG
OUT 2
12
11
10
9
13
LIMITER
CAP FG
PREAMP
CAPSTAN
FGx2
LOGIC
CAP FG
COMPRATOR
PDML
NC
NC
NC
NC
NC
NC
COMPARATOR
Vcc
REG
DRUM FG
COMPARATOR
DRUM
FG
PREAMP
PG
COMPARATOR
PG
PREAMP
LEVEL
SHIFT
1
2
3
4
ACAL 5
LGND 6
VL+ 7
AGND
APD
AINL+
AINL-
+
–
1
2
3
4
5
6
7
8
DRUM
COM
DRUM
FG IN
DRUM
FG OUT
DRUM
PG IN
NC
PEAK
HOLD
DRUM
PG OUT
GND
BUFFER
– 68 –
8
9
10
11
12
13
14
24
CXD8493M (AUDIO board)
VOLTAGE
REFERENCE
+
–
LP FILTER
GCA CTL
CAP LIM
IN
14
IC307
CAP AMP
OUT
16 15
CAP FG
IN 1
NC
CAP FG
IN 2
CX20115A (DRUM DRIVE board)
23
B LPC
22
+
–
DAC
18 19 20 21
EQ IN
17
SWA OUT
15 16
PB GND
14
EQ Q
13
FLT OUT
REG
B HA OUT
P ENV IN 12
IC3
26 B HA IN
PILOT
OCA
+
–
+
–
+
–
DAC
P ENV OUT 11
LP FILTER
IC1
+
–
28 VREF +
27
26
25
24
23
22
VREF AINR +
AINR VA VA +
21
20
19
18
17
16
15
PDMR
NC
NC
NC
NC
NC
NC
I CKL
IC309 SN74HC74AN
(AUDIO board)
14 13 12 11
VCC
10
IC312 SN74HC4020ANS
(AUDIO board)
VCC
16
9 8
Q11
15
Q10
14
Q8
13
Q9 RESET CLOCK
12
11
10
Q11
Q10
Q8
Q9
R
CLK
Q13
Q14
Q6
Q5
Q7
Q4
2
Q13
3
Q14
4
Q6
5
Q5
6
Q7
7
Q4
Q1
9
PR
Q
Q
D
CK
CLR
PR
D
Q12
Q
1
Q12
Q
CK
CLR
1 2 3
4 5 6
32 31
30 29 28 27 26 25 24 23 22 21 20
XSEL
SPLM
DFVDD1
DVDDR
VSUB(D)R
VSUB(C)R
VDD2
VDD
R1(-)
VSS
R1(+)
VSS2
CXD8505BQ (AUDIO board)
SYSM 33
ATT
SHIFT
LATCH
XINT
34
35
36
37
"O" DETECT
MUTE
CIRCUIT
MODE
PLM
S/P
ATT
FIR2
FIR3
3RD ORDER
NOISE
SHAPER
CLOCK
GENERATOR
AC, DC
DITHER
FIR1
FIR2
FIR3
L. I. P.
(x 8)
IIR
3RD ORDER
NOISE
SHAPER
PLM
TIMING
CIRCUIT
IC315
L1(-)
VSS
L1(+)
TC5081AP (AUDIO board)
– 69 –
7
8
9
GND
6
S
5
R
4
N. C.
3
VDD
2
PHASE OUT
1
AIN
PHASE
COMPARATOR
VSS2
61 62 63 64
MUTE L
TEST 1
TEST 2
DFVDD2
DV DDL
VSUB(D)L
VSUB(C)L
VDD2
VDD
52 53 54 55 56 57 58 59 60
AOUT
45
46
47
48
49
50
51
L. I. P.
(x 8)
IIR
ATT
512FS0
256FS0
128FS0
I NV1
I NV01
I NV02
MUTE R
FIR1
PDOUT
XDCK 38
XLRCK 39
DATA1 40
VSUD(D)R 41
DF VSS 42
VSUB(D)L 43
INAF 44
8
GND
GND
7
201x16
IC314
Q1
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
VSS2
R2(+)
VSS
R2(-)
VDD
VDD2
VSUB(A)R
XVSS
XVSS
X IN
X OUT
XVDD
VSUB(A)L
VDD2
VDD
L2(-)
VSS
L2(+)
VSS2
CLOCK
12
3Q
4D
3D
13
3Q
4Q
14
11
10
9
Q
Q
CLR
A8
•
BUFFER
ROW
DECODER
•
•
•
•
MEMORY
MATRIX
512x512
•
•
A13
A8
•
A7 3
A6 4
A5 5
•
A9
A11
•
•
A10
A4 6
•
A3 7
•
A2 8
•
A1 9
•
A10
I/O GATE
COLUMN
DECODER
BUFFER
25 A8
CK
CLR
Q
24 A9
23 A11
•
OE
A0 10
CE
D CK
26 A13
22 OE
1
2
21 A10
IC516
20 CE
NC
8
D
D
CK
CLR
Q
Q
Q
6
7
3
4
5
8
GND
•
2Q
•
A9
Q
CK D
2Q
A11
Q
CLR
27 WE
2D
WE
•
1D
•
A12 2
M51953BFP (DIGITAL board)
VDD
7
OUTPUT
6
DELAY
CAPACITANCE
5
19 I/08
18 I/07
5µA
I/01 11
OE
–
17 I/06
BUFFER
I/03 13
15
1Q
A13
I/02 12
16
28 VCC
1Q
A14 1
MC74HC175F (DIGITAL board)
4Q
IC512
VCC
CXK58257BM (DIGITAL board)
CLEAR
IC504
I/O BUFFER
+
WE
16 I/05
CE
1.25V
15 I/04
1
2
3
4
NC
NC
NC
GND
GND 14
AT24C01A-10 SC (DIGITAL board)
VDD
TEST
SCL
SDA
IC517
8 7 6 5
START
STOP
LOGIC
IC511 SN74HC153ANS
(DIGITAL board)
SERIAL
CONTROL
LOGIC
OUTPUT
2Y
9
2C2 2C1 2C0
12 11 10
2C3 2C2 2C1 2C0
DEVICE
ADDRESS
COMPARATOR
2Y
2G
R/W
B
B
A
DATA REGISTER
LOAD
B
A
DOUT/ACK
LOGIC
DIN
1C1 1C0
2
4
1
3
STROBE
B
1C3 1C2
1G
SELECT
5
6
1C1 1C0
SERIAL MIX
A
1G
1C3 1C2
2
E PROM
A
Y DEC
B
INC
DATA WORD
ADDRESS/
COUNTER
X DEC
STROBE A
2G SELECT 2C3
13
15
14
H.V. PUMP/TIMING
LOAD
COMP
DATA INPUTS
VCC
16
EN
1Y
DOUT
7
8
OUTPUT GND
1Y
1 2 3 4
A0
A1
A2
GND
DATA INPUTS
– 70 –
MSM6782-01-MS (DIGITAL board)
CONTROL
REGISTER
(CD, CE, CF)
STD.P 1
TIME
REGISTER
(SEC-YEAR, WEEK)
IC523
M54641L (DIGITAL board)
VCC 1
8 VDD
8 VCC
REG
OUT2 2
DATA
BUFFER
CONTROL
ADDRESS
COUNTER
6 IN 2
INPUT
AMP
CLK 3
CE 4
5 VSS
IC702
7 OUT1
INPUT
AMP
IN 1 3
POWER
AMP
5 REFERENCE
GND 4
MSM6338RS (DISPLAY board)
16 VDD
15 A1
14 A2
DATA 1
0dB OVER
COUNTER
0dB
OVER
DETECTION
CIRCUIT
(BI-DIRECTION)
16BIT S.R
BCK 2
0dB
OVER
LATCH
L.R
0dB OVER
COUNTER
RD
READ
WRITE
LOGIC
WR
DATA 2
I/O
7 XT
6 XT
OSC
DECODER
POWER
AMP
CS
IC518
LRCK 3
ABSOLUTE
CIRCUIT
RESET 4
WR 5
RD 6
CS 7
MAX
REG
(L-CH)
15BIT
LATCH
15BIT LATCH
WR
RD
CS
A
COMP
B
CONTROL
&
OVER
REG
CONTROL
CIRCUIT
OUT
REG
16BIT
LATCH
MPX
MAX
REG
(R-CH)
15BIT
LATCH
A≥B
VSS 8
IC703
Vcc
16
SN74HC174AN (DISPLAY board)
6Q
15
6D 5D
14 13
D
Q
4Q CLOCK
10
9
D
CLEAR
CK
CLEAR
CK
D
Q
D
3 4
1D 2D
– 71 –
Q
CK
CLEAR
CK
CLEAR
CLEAR
CK
1 2
CLEAR 1Q
Q
D
CK
CLEAR
Q
5Q 4D
12 11
D
5 6
2Q 3D
Q
7
8
3Q GND
13 DB3
12 DB2
DATA
BUS
BUFFER
11 DB1
10 NC
9 DB0
4-12.
IC PIN FUNCTION DESCRIPTION
• AUDIO BOARD IC308 CXD8482Q (SBM + Digital Filter)
Pin No.
1
2
3
Pin Name
TEST
NC
SYNC
I/O
I
—
I
4
INIT
I
5
6
7, 8
9
10
11
12
13
14
15, 16
17
18
19
20
21
22, 23
24, 25
26
27
28
29
30
31
32
33
34
35
36
NC
CFLG
VDD
LRKI
BKI
NC
DLI
DRI
IFLG
NC
FE
AL2
AR2
AL1
AR1
VSS
CVSS
FCLK
MCLK
CVDD
NC
IBIT
NC
VSS
SCALE
ISEL1
ISEL2
NC
—
O
—
I
I
—
I
I
O
—
I
I
I
I
I
—
—
O
I
—
—
I
—
—
I
I
I
—
37
DITH
I
38
BOOST
I
39
40
41
42
43
VDD
MODE
SHIFT
LATCH
NC
—
I
I
I
—
44
LC
I
45
SBM
I
Function
Test input pin. “H” for test mode and “L” for normal mode. (Fixed at “L” level in this set.)
Empty pin
Sync mode setting pin. “H” for INT master mode and “L” for EXT slave mode.
A/D converter power down mode input from main microcomputer (IC501). (“H” active)
(This IC is set OFF in digital input/output mode.)
Empty pin
FE calibration flag output (Not used in this set, empty pin.)
Power supply pin (+5V)
L/R clock input (Not used in this set, fixed at “L” level.)
Beat clock input (Not used in this set, fixed at “L” level.)
Empty pin
L channel data input (Not used in this set, fixed at “L” level.)
R channel data input (Not used in this set, fixed at “L” level.)
FE sync flag output (Not used in this set, empty pin.)
Empty pin
FE select input (Not used in this set, fixed at “L” level.)
Data signal (L) input (Not used in this set, fixed at “L” level.)
Data signal (R) input (Not used in this set, fixed at “L” level.)
Data signal (L) input from A/D converter (IC307).
Data signal (R) input from A/D converter (IC307).
Ground
Ground
Output of 128fs master clock for FE to A/D converter (IC307).
Input of 256fs master clock from FS clock generator (IC325).
Power supply pin (+5V)
Empty pin
64fs input data mode select input (“H”: 4bit, “L”: 1bit) (Fixed at “L” level in this set.)
Empty pin
Ground
Scale select input (“H”: ×4, “L”: ×5) (Fixed at “L” level in this set.)
FS select of input data (Fixed at “L” level in this set.)
FS select of input data (Fixed at “L” level in this set.)
Empty pin
Dither control input. Dither active when “H” and stopped when “L”.
(Not used in this set, empty pin.)
Boost control input. Boost active when “H” and normal when “L”.
(Fixed at “H” level in this set.)
Power supply pin (+5V)
Serial data signal input from main microcomputer (IC501).
Shift clock signal input from main microcomputer (IC501). (Shift when ↓, latch when ↑)
Latch pulse signal input from main microcomputer (IC501).
Empty pin
Low cut control input. “H” for low frequency cut and “L” for flat. (Fixed at “H” level in this
set.)
Super Bit Mapping (SBM) control input from main microcomputer (IC501).
(“H”: ON, “L”: OFF)
– 72 –
Pin No.
46
Pin Name
NC
I/O
—
47
OSEL
I
48
49
50
51
52, 53
54
55
56
57
58
59
60
OBIT
DRO
DLO
NC
VSS
BCK
NC
LRCK
OFLG
VDD
OVR
OVL
I
O
O
—
—
I
—
I
O
—
O
O
Function
Empty pin
FS select of data output. (“H”: 2FS output or EX mode, “L”: FS output)
(Fixed at “L” level in this set.)
Bit select of data output. (“H”: 24 bits, “L”: 16 bits) (Fixed at “L” level in this set.)
Write clock output (Not used in this set, empty pin.)
L/R channel data signal output
Empty pin
Ground
Bit clock input from digital filter (IC314).
Empty pin
L/R clock input from digital filter (IC314).
Outside sync flag output (Not used in this set, empty pin.)
Power supply pin (+5V)
R channel side overflow flag output (Not used in this set, empty pin.)
L channel side overflow flag output (Not used in this set, empty pin.)
– 73 –
• DIGITAL BOARD IC501 CXP87540-033Q (Main Microcomputer)
Pin No.
1
2
3
4, 5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23 — 27
Pin Name
SBM-ON
XBAL
OBIT-SEL
—
PRE-EMPH
AUSO
AUSC
VCO-EN
XOPT/COA
XADLD
XDALD
FADE-WE
FADE-RST
XANA/DIG
XREC/PB
XREPRO
MIC-ATT
MIC-ON
RTC-DT
RTC-SC
RTC-CE
—
28
FS48
29
FS44
30
FS32
31
32
33
34
35 — 38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
XLM
—
SLV-MUT
XSLV-SEL
AF3 — AF0
MP
XRST
VSS
XTAL
EXTAL
XDISP-REQ
—
XMECH-REQ
—
XDISP-ACK
DM-DI
DM-DO
DM-CK
XSBSY
SR-DTI
I/O
Function
O SBM (Super Bit Mapping) ON/OFF select pin (“L”: OFF, “H”: ON)
O Analog input select (“L”: BAL, “H”: UNBAL)
O Not used.
— Empty pin
O Not used in this set.
O Digital filter control serial data output pin
O Digital filter control serial clock output pin
O DIGITAL IN REC mode only for “H” output.
O Select (“L”: COAXIAL, “H”: OPTICAL)
O A/D digital filter control latch output pin
O D/A digital filter control latch output pin
O Not used in this set.
O Not used in this set.
O ANALOG/DIGITAL IN select output pin (“L”: ANALOG IN, “H”: DIGITAL IN)
O Record/playback select output pin (“L”: REC, “H”: PB)
O Not used in this set.
O Not used in this set.
O Not used in this set.
I/O Clock IC serial data input/output pin
O Clock IC serial data output pin
O Clock IC chip enable output pin
— Empty pin
Fs select output pin
O
Fs 32kHz
Fs 44.1kHz
Fs 48kHz
Pin
L
L
H
@,
O
L
H
L
Pin @.
O
H
L
L
Pin # /
O
—
O
O
I
—
I/O
—
O
I
O
—
O
—
I
I
O
O
I
I
Line mute output pin (“L”: ON, “H”: OFF)
Empty pin
Not used in this set.
Not used in this set.
Pull-up fixed.
Connected to Ground.
System reset input/output pin (“L”: ACTIVE)
Ground
Not used.
Operating clock input pin (9.408MHz)
Pin for communication request output to display controller.
Not used.
Pin for communication request output to mechanism microcomputer.
Not used.
Pin for communication acknowledge input from display controller.
Pin for serial data input from another microcomputer.
Pin for serial data output to another microcomputer.
Pin for serial clock output to another microcomputer.
Pin for SBSY input from master DAT-DSP IC.
Pin for serial data input from master DAT-DSP IC.
– 74 –
Pin No.
54
55
56
57
58
59
60
61
62
63
Pin Name
SR-DTO
SR-CK
AVSS
AVREF
AVDD
XMECH-BSY
FOOT-SW1
FOOT-SW0
MODE1
MODE0
I/O
O
O
—
—
—
I
I
I
I
I
64
X24/12
I
65
66
67
68
69
70
71
72
73
74
75, 76
77 — 79
80
81 — 85
86
87
88
89
90
91, 92
93
94
95
96
97
98
99, 100
DATE-ODR
PRL-REM
X4HEAD
XPRODIO
XFADER
MUT-MONIT
XAES/COA
XCNT-S
MODE3
MODE2
LED1, 0
—
ERRO
—
XTEST
POW-DWN
VSS
VDD
VPP
—
XADINT
XDAINT
REC-DIS
EXSY-MUT
XMST-SEL
MST-MUTE
—
I
I
I
I
I
I
I
I
I
I
O
—
—
—
I
I
—
—
—
—
O
O
O
O
O
O
—
Function
Pin for serial data output to master DAT-DSP IC.
Pin for serial clock output to master DAT-DSP IC.
Ground
Reference voltage pin (+5V)
Power supply pin (+5V)
Pin for communication busy input from mechanism microcomputer. (“L”: BUSY)
Pull-up fixed.
Pull-up fixed.
Fixed at “L” level.
Fixed at “H” level.
24/12-hour system display select input pin (“H”: 12-hour system display (US, Canadian
model), “L”: 24-hour system display (AEP, UK, German model)).
YY-MM-DD/DD-MM-YY display select input pin (“L”: Fixed to DD-MM-YY display)
Pull-up fixed. Para-remote A/D input. (At connect with controller.)
Fixed at “H” level.
Fixed at “L” level.
Fixed at “H” level.
Pin for mute monitor input from master DAT-DSP IC.
COAX↔AES/EBU Switch signal input.
Pull-up fixed.
Fixed at “H” level.
Fixed at “H” level.
Remote commander LED output pin
Not used.
TEST pin. (Not used.)
Not used.
TEST pin (“L”: TEST MODE)
Fixed at “H” level.
Ground
Power supply pin (+5V)
Connect to VDD.
Not used.
A/D digital filter initial setting output pin (“L”: INIT)
D/A digital filter initial setting output pin (“L”: INIT)
Recording current control output pin (“L”: Normally, “H”: Recording current forced OFF)
EXSY output control pin (“L”: Normally, “H”: EXSY forced OFF)
Signal process IC chip select output pin
Playback data mute output pin (“L”: OFF, “H”: ON)
Not used.
– 75 –
• DIGITAL BOARD IC502 CXP87532-012Q (Mechanism Microcomputer)
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
Pin Name
FPM-KI
CAP-RVS
BPM-ON
BPM-KI
DRM-ON
—
—
—
—
—
—
—
—
—
LM-EJCT
LM-LOAD
CM-OUT
CM-IN
XROM-CK
XROM-DT
—
—
H-FIX
H-FIX
CAS-IN
REC-EN
CAS-LCK
CAS-OUT
UNLD-SW
LOAD-SW
—
—
—
—
H-FIX
H-FIX
H-FIX
H-FIX
MP
XRST
VSS
XTAL
EXTAL
XMECH-BSY
—
TLED-ON
SLED-ON
XSBSY
I/O
Function
O FWD plunger kick control output
O Capstan rotation direction control output. “H” for FWD and “L” for REV.
O Brake plunger ON control output
O Brake plunger kick control output
O Drum motor ON control output
O
O
O
O
O Not used.
O
O
O
O
O Loading motor rotation direction control output (Eject direction)
O Loading motor rotation direction control output (Loading direction)
O Cassette compartment motor rotation direction control output (OUT direction)
O Cassette compartment motor rotation direction control output (IN direction)
O EEPROM serial clock output
I/O EEPROM serial data input/output
O
Not used.
O
I
Not used. (Fixed at “H” level.)
I
I
Cassette IN switch input
I
REC enable switch input
I
Cassette compartment lock switch input
I
Cassette compartment OUT switch input
I
UNLOAD switch input. “H” in UNLOAD position.
I
LOAD switch. “H” in STOP position.
O
O
Not used.
O
O
I
I
Not used. (Fixed at “H” level.)
I
I
— Connect to Ground.
I
Reset input. “L” for reset.
— Ground
O Crystal oscillator output pin (9.408MHz). (Not used in this set.)
I
Crystal oscillator input pin (9.408MHz)
O Mechanism microcomputer BUSY signal input
O Not used.
O T-END sensor ON output. “H” for ON.
O S-END sensor ON output. “H” for ON.
I
SUB SYNC input from main microcomputer (IC501).
– 76 –
Pin No.
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
Pin Name
—
—
—
XMECH-REQ
MECH-DTI
MECH-DTO
MECH-SCK
AVSS
AVREF
AVDD
TEND
SEND
H-FIX
H-FIX
THICK
SET-MODE
CAS-MODE
ATF-IN
TFG
SFG
CFG
DFG
DPG
DREF
ATF-S2
H-FIX
—
XCAS-TST
MST-CLK
PBDT
SWP
AGC-PWM
T-PWM
S-PWM
D-PWM
C-PWM
H-FIX
XTEST
POW-DWN
VSS
VDD
VPP
ATF-S2
AREA
—
—
—
XLP-REC
I/O
I
O
O
I
I
O
I
—
—
—
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
O
I
I
I
O
O
O
O
O
O
I
I
I
—
—
—
O
O
O
O
O
O
Pin Description
Not used.
Communication request input from main microcomputer (IC501).
Serial data input from main microcomputer (IC501).
Serial data output to main microcomputer (IC501).
Serial clock input from main microcomputer (IC501).
A/D port Ground
A/D port power supply (+5V)
A/D port power supply (+5V)
T-END sensor input
S-END sensor input
Fixed at “H” level.
Thick switch input
Fixed at “H” level.
Fixed at “H” level.
ATF pilot signal input
T reel FG signal input
S reel FG signal input
Capstan FG signal input
Drum FG signal input
Drum PG signal input
Drum reference signal input
Input of AFT sampling pulse for DPG automatic adjustment.
Not used. (Fixed at “H” level.)
Not used.
Test pin. “L” for cassette compartment without test mode.
Master clock input
PB data for ATF SYNC.
Switching pulse output
Output of PWM signal for AGC.
Output of PWM signal for T reel.
Output of PWM signal for S reel.
Output of PWM signal for drum.
Output of PWM signal for capstan.
Not used. (Fixed at “H” level.)
Test pin. “L” for test mode. (Used at D PG, PATH and torque.)
Not used. (Fixed at “H” level.)
Ground
+5V power supply
Connect to +5V.
ATF sampling pulse #2 output
AREA signal output
Not used.
LP REC control output. “L” for LP mode RED.
– 77 –
Pin No.
97
98
99
100
Pin Name
—
—
XTLK
FPM-ON
I/O
O
O
O
O
Function
Not used.
Reel motor T LOCK control output. “L” for T LOCK.
FWD plunger ON control output
– 78 –
• DIGITAL BOARD IC503 CXD2605Q (Master DAT-DSP)
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Pin Name
A8
A9
VDD
A10
A11
A12
A13
A14
XWE
XOE
XEAN
TST1
XT1O
XT1I
VSS
XRST
I/O
O
O
—
O
O
O
O
O
O
O
O
I
O
I
—
I
17
CLKO
O
18
MINT
O
19
20
21
ATSY
MCLK
DREF
I
O
O
22
SBPM
O
23
24
25
26
27
EXCK
SDSI
SDSO
SBSY
PLRF
I
I
O
O
O
28
CCLK
O
29
30
31
32
33
34
MUTE
MUTM
UNLK
RFCT
SYMN
SELB
I
O
O
I
O
I
35
PLCK
O
36
37
38
39
40
TST2
RFDT
XCS
SWP
VSS
I
I
I
I
—
41
PIPC
O
42
43
REPB
REDT
O
O
Function
External RAM address output
External RAM address output
+5V
External RAM address output
External RAM address output
External RAM address output
External RAM address output
External RAM address output
External RAM write enable signal output
External RAM output enable signal output
External addressing enable signal output. (Not used in this set.)
Test input (Fixed at “L” level.)
X’tal oscillation circuit 1 output
X’tal oscillation circuit 1 input
Ground
Reset input. “L” for reset.
System clock output. (The frequency is 4.9152 MHz when SELC is set “L” and 8.192 MHz
when SELC is set “H”.) (Not used in this set.)
Control byte (1). Bit 1: Q code decode (intercurve detection) output when “L” and BCK clock
output by RX-PLL when “H”. (Not used in this set.)
ATF sync signal input
Channel clock (fch) output (Not used in this set.)
SBSY cycled Duty 50 signal output
Control byte (1). Bit 1: Output of monitor signal for data transfer to and from microcomputer
when “L” (“L” to permit transfer) and F256 clock output by RX-PLL when “H”.
(Not used in this set.)
Input of clock for data transfer to and from main microcomputer (IC501).
Serial data input from main microcomputer (IC501).
Serial data output to main microcomputer (IC501).
Output of frame sync signal for data transfer to and from main microcomputer (IC501).
Output of PLL clock divided by 5880. (Not used in this set.)
9.8304MHz output when SELC is “L” and 12.288MHz output when SELC is “H”.
(Not used in this set.)
Mute input. Set “H” to mute, but REC monitor sound will not be muted.
Mute monitor. “H” in muting.
RX-PLL lock monitor signal output. “L” in locking.
Area signal input. (“L” to enable AREA signal and “H” to disable AREA signal.)
RF associated C1 check result monitor signal output. (Not used in this set.)
Test pin (Fixed at “H” level.)
Control byte (1). Bit 1: RF-PLL clock output when “L” and F128 clock output by RX-PLL
when “H” (Not used in this set.)
Test pin (Fixed at “L” level.)
Playback RF signal input
Input of chip select signal for data transfer to and from microcomputer. “L” to permit transfer.
RF switching pulse. “L” to select A track and “H” to select B track.
Ground
Output of ATF pilot signal/descrimination signal for recording signal. “H” to output pilot
signal.
REC/PB descrimination signal output. “H” for REC mode.
Recording signal output.
– 79 –
Pin No.
44
45
46
47
48
Pin Name
TST4
PDO
SELC
MUTA
PLCO
I/O
I
O
I
I
I
49
PLVR
O
50
PLRF
O
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
MSSL
RX
VDD
TX
SELA
EXSY
EXSN
F128
F256
F512
ADLF
DALF
XT2O
XT2I
VSS
XT3O
XT3I
FSEN
LR03
I
I
—
O
I
I/O
I/O
I/O
O
O
I
I
O
I
—
O
I
I
O
70
LR02
O
71
72
73
74
75
76
77
78
79
80
81
82
LR01
LRCK
WCK
XBCK
BCK
ADDT
DADT
DADO
ADDI
ADDN
ERRI
ERRF
O
I/O
O
O
I/O
I
O
I
O
I
I
O
83
MNTG
O
84
85
86
87
88
89
90
D7
D6
D5
D4
D3
D2
VSS
I/O
I/O
I/O
I/O
I/O
I/O
—
Function
Test pin (Fixed at “L” level.)
RX-PLL phase comparator output
Oscillation frequency select signal input (Fixed at “L” level in this set.)
Mute input. “H” to mute, and REC monitor sound is also muted.
RX-PLL’s external VCO clock input (512fs reference)
Output of phase comparator signal for RX-PLL. (2fs generated from PLL clock.)
(Not used in this set.)
Output of phase comparator signal for RX-PLL. (RX SYNC detect signal 2fs)
(Not used in this set.)
Master mode/slave mode slelect. “H” for master mode. (Fixed at “H” level in this set.)
Digital interface signal input
+5V
Digital interface signal output
Test pin (Fixed at “L” level.)
External sync signal input/output
External sync signal input/output
128fs signal/256fs signal (high speed) input/output
256fs signal/512fs signal (high speed) output (Not used in this set.)
512fs signal output (Not used in this set.)
ADDT, ADDI, ADDN serial data LSB/MSB first select input. “L” for LSB first.
DADT, DADO serial data LSB/MSB first select input. “L” for LSB first.
X’tal oscillation circuit 2 output. (Not used in this set.)
X’tal oscillation circuit 2 input
Ground
X’tal oscillation circuit 3 output
X’tal oscillation circuit 3 input
F128, BCK, LRCK input/output select input. “H” for output.
Inverted LR02 signal (Not used in this set.)
Control byte (1). Bit 1: 16BCK delayed LRCK signal when “L” and LRCK clock output by
RX-PLL when “H” (Not used in this set.)
15BCK delayed LRCK signal
fs/2fs (high speed) signal input/output
2fs/4fs (high speed) signal output (Not used in this set.)
Inverted BCK signal output
64fs/128fs (high speed) signal input/output
AD serial data input
DA serial data output
DIGITAL OUT audio data input
DIGITAL IN audio data output
DIGITAL IN audio data input
DIGITAL OUT Validity flag data input
DADT data’s interpolation data/descrimination signal output. “H” for interpolation data.
“H” output indicates that error correction status monitor data is being output to D7 to D0.
(Not used in this set.)
External RAM data input/output (MSB)
External RAM data input/output
External RAM data input/output
External RAM data input/output
External RAM data input/output
External RAM data input/output
Ground
– 80 –
Pin No.
91
92
93
94
95
96
97
98
99
100
Pin Name
D1
D0
A0
A1
A2
A3
A4
A5
A6
A7
I/O
I/O
I/O
O
O
O
O
O
O
O
O
Function
External
External
External
External
External
External
External
External
External
External
RAM data input/output
RAM data input/output (LSB)
RAM address output
RAM address output
RAM address output
RAM address output
RAM address output
RAM address output
RAM address output
RAM address output
– 81 –
• DISPLAY BOARD IC701 CXP82320-077Q (Display Controller)
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16 — 19
20
21
22 — 29
30
31
32
33
34 — 57
58 — 70
71
72
73
74 — 77
78
79
80
Pin Name
MODE
RMC
TEST
A1 METER
A2 METER
LED-CLK
ACK
SC
SI
SO
CS METER
RD METER
WR METER
M MUT
REM-SEL
B1 — B4
A JOG
B JOG
AD0 — AD7
XRST
EXTAL
XTAL
VSS
S0 — S23
T12 — T0
VFDP
VDD
NC
D0 — D3
H
X DISP REQ
H
I/O
I
I
I
O
O
O
O
I
I
O
O
O
O
I
O
I
I
I
I
I/O
I
O
—
O
O
I
—
—
I/O
I
I
I
Function
Fixed at “H” level.
Remote control input from IC704.
Test mode setting pin
Address 1 output to IC702.
Address 2 output to IC702.
Pin for CLK output to IC703.
Pin for acknowledge output to main microcomputer (IC501).
Pin for serial clock input from main microcomputer (IC501).
Pin for serial data input from main microcomputer (IC501).
Pin for serial data output to main microcomputer (IC501).
Pin for chip select output to IC702.
Pin for read output to IC702.
Pin for write output to IC702.
Level meter mute input pin
Pin for remote selector output to IC704.
Pin for shuttle signal input
Pin for jog signal input.
Key input pins
System reset pin (active “L”)
System clock input pin
System clock output pin (4.19MHz)
Ground
FL tube segment output pins
FL tube grid output pins
Power supply pin (–30V)
Power supply pin (+5V)
Connect to VDD.
Pin for data input/output to and from IC702.
Fixed at “H” level.
Pin for comunication request input from main microcomputer (IC501).
Fixed at “H” level.
– 82 –
SECTION 5
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Color Indication of Appearrance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of the
electrical parts list.
The components identified by mark
! or dotted line with mark ! are
critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque ! sont critiquens pour la
sécurité.
Ne les remplacer que par une pièce
portant le neméro spécifié.
(1) CASE SECTION
5
4
4
4
3
3
#2
4
#1
not supplied
2
1
Front panel section
#1
Ref. No.
Part No.
Description
1
2
* 3
3-007-485-01 LID (CASSETTE COMPARTMENT)
3-007-486-01 WINDOW (CASSETTE COMPARTMENT)
4-951-532-01 CUSHION
Remark
Ref. No.
Part No.
4
* 5
3-704-366-21 SCREW (CASE) (M3X10)
4-986-210-01 CASE
– 83 –
Description
Remark
(2) FRONT PANEL SECTION
supplied with
RV302
54
56
55
56
56
57
not
supplied
58
56
56
71
68
supplied with
J304
59
70
69
67
56
60
56
#15
53
56
54
61
65
56
66
52
not
supplied
supplied with
RV103, 203
62
64
not supplied
63
#3
52
Ref. No.
Part No.
Description
51
52
53
54
* 55
3-007-731-01
X-4947-852-1
4-908-848-31
3-917-216-31
1-664-483-11
PANEL, FRONT
KNOB (1) ASSY
EMBLEM, SONY
KNOB (TIMER)
REM SW BOARD
56
* 57
58
* 59
* 60
4-951-620-01
1-664-486-11
1-769-541-11
A-2007-647-A
1-664-487-11
SCREW (2.6X8), +BVTP
HP BOARD
WIRE (FLAT TYPE) (17 CORE)
DISPLAY BOARD, COMPLETE
SHUTTLE BOARD
* 61
1-664-485-11 REC VOL BOARD
51
Remark
Ref. No.
Part No.
Description
62
63
64
65
66
4-983-619-11
3-354-981-01
4-983-620-01
4-986-398-01
X-3372-928-1
RING, SHUTTLE
SPRING (SUS), RING
DIAL, JOG
WINDOW, INDICATION
BASE ASSY, PANEL
67
68
69
* 70
* 71
4-986-220-12
4-986-217-12
4-986-218-01
1-664-484-11
3-703-397-01
BUTTON (PLAY)
BUTTON (AMS)
BUTTON (3 KEY)
INPUT SW BOARD
STOPPER,WIRE
72
– 84 –
9-911-863-XX SHEET
Remark
(3) CHASSIS SECTION
r A: AUDIO board
r B: DIGITAL board
AEP
104
105
107
103
#6
109
#1
#1
#1
106
#1
#3
102
120
108
120
#4
T901
#4
118
117
119
#1
#5
110
115
116
113
114
111
117
#1
#1
#1
rB
rA
112
101
#1
not supplied
101
#1
121
Ref. No.
Part No.
Description
101
102
* 103
104
105
4-956-885-01
4-923-520-71
4-986-225-01
4-988-365-01
4-812-134-11
* 106
107
* 108
* 109
* 109
1-664-488-11
3-724-182-01
A-2007-645-A
3-007-688-11
3-007-688-21
* 110
* 111
A-2007-642-A ANA OUT BOARD, COMPLETE
A-2007-651-A ANA IN BOARD, COMPLETE
Remark
Ref. No.
Part No.
Description
FOOT (F58175S2W)
BUTTON,POWER
LEVER (POW)
COVER (D)(AEP)
RIVET (DIA. 3.5), NYLON (AEP)
* 112
113
* 114
* 115
116
A-2007-648-A
1-769-542-11
A-2007-646-A
1-664-490-11
3-846-068-00
MAIN BOARD, COMPLETE
WIRE (FLAT TYPE) (31 CORE)
UNBAL BOARD, COMPLETE
REG BOARD
SPACER(D)
PRIMARY BOARD
NUT (SMALL JACK), M6
REMOTE BOARD, COMPLETE
PANEL, BACK (US,Canadian)
PANEL, BACK (AEP)
117
* 118
* 119
120
121
4-924-098-81
1-664-494-11
A-2007-643-A
4-886-821-11
3-831-441-11
HOLDER, PC BOARD
DIG OUT BOARD
DIG IN BOARD, COMPLETE
SCREW,S TIGHT,+PTTWH 3×6
CUSHION (F)
! T901
! T901
1-431-064-11 TRANSFORMER, POWER (US,Canadian)
1-431-065-11 TRANSFORMER, POWER (AEP)
– 85 –
The components identified by
mark ! or dotted line with
mark ! are critical for safety.
Replace only with part number
specified.
Remark
Les composants identifiés par une
marque ! sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le neméro spécifié.
(4) CASSETTE COMPARTMENT SECTION-1
not supplied
167
A
163
168
170
164
165
B
158
#10
160
158
#23
163
162
158
161
#9
162
169
A
#24
166
159
B
157
156
155
172
#7
158
159
#10
#8
154
171
not
supplied
153
152
151
Ref. No.
Part No.
Description
* 151
152
153
154
* 155
X-3371-758-1
3-373-225-01
3-373-220-01
3-373-224-01
3-373-217-01
PLATE ASSY, FULCRUM
HOLDER (WINDOW)
ARM (JOINT)
HOLDER (LOWER)
SHAFT (JOINT)
156
157
158
159
160
3-373-223-01
3-373-222-01
3-318-201-11
3-345-648-61
3-373-219-01
SLIDER (L)
SLIDER (R)
SCREW (B) (1.4X3), TAPPING
SCREW (M1.4), TOOTHED LOCK
LEVER (L)
161
3-373-218-01 LEVER (R)
Remark
Ref. No.
Part No.
Description
162
163
164
165
166
3-632-859-00
3-318-203-61
3-373-216-01
3-373-215-01
3-373-237-03
SPRING, BRAKE LEVER RETURN
SCREW (B1.7X4), TAPPING
SPRING (L), TORSION
SPRING (R), TORSION
HOLDER (UPPER), CASSETTE
167
168
169
* 170
* 171
3-307-948-21
4-931-471-01
3-373-212-01
3-909-720-11
X-3371-759-1
WASHER, NYLON
SCREW (STEP)
SPRING (CASSETTE)
REINFORCEMENT
PLATE (R) ASSY, SIDE
172
– 86 –
3-908-780-01 SHEET
Remark
(5) CASSETTE COMPARTMENT SECTION-2
not supplied
208
#12
M905
205
not supplied
#21
204
#19
DATM-55
207
203
206
#10
207
207
202
201
Ref. No.
Part No.
Description
201
202
203
* 204
* 205
3-562-462-00
3-373-214-01
3-373-213-01
X-3364-426-1
1-655-916-11
BELT, CAPSTAN
PULLEY
GEAR, DRIVING
SLIDER ASSY
SW BOARD
Remark
Ref. No.
Part No.
Description
206
207
* 208
M905
A-2003-907-I
2-623-756-01
1-655-913-11
X-3370-655-1
CHASSIS (L) ASSY
SCREW, (B1.7X3), TAPPING
MOTOR BOARD
MOTOR ASSY (CASSETTE COMPARTMENT)
– 87 –
Remark
(6) MECHANISM DECK SECTION-1
(DATM-55)
not supplied
273
#20
#11
253
254
#11
259
261
260
M901
262
#22
271
255
not
supplied
264
263
272
#25
274
#14
265
255
#11
258
251
267
252
268
#16
269
not supplied
#13
PM902
266
270
not supplied
257
256
Ref. No.
Part No.
Description
REC EN BOARD
WASHER, POLYETHYLENE
RF AMP BOARD, COMPLETE
RF COMPLETE ASSY
SCREW (M1.7X3.5), TAPPING
264
* 265
* 266
267
268
3-564-035-01
1-655-285-11
1-654-391-11
3-337-626-01
X-3337-610-1
SPRING, COMPRESSION
LOAD SW BOARD
T END BOARD
CAP, PINCH ROLLER
PINCH ROLLER ASSY
SCREW (P1.7X1.6)
SPRING (PINCH)
DETECTION (R) ASSY, E
LOADING MOTOR BOARD
SCREW, (B1.7X3), TAPPING
269
270
271
* 272
* 273
3-701-436-11
X-3362-021-1
3-366-886-01
1-654-394-12
3-929-800-01
WASHER, STOPPER
LEVER (PINCH ROLLER) ASSY
SHEET (RF BRACKET)
THICK BOARD
BRACKET (RF)
Ref. No.
Part No.
Description
* 251
252
* 253
* 254
255
1-654-393-11
3-344-781-01
A-2006-455-A
A-2001-587-A
3-321-041-01
256
257
258
* 259
260
3-704-244-01
3-931-541-01
A-2004-299-A
1-655-286-11
2-623-756-01
261
262
263
3-703-502-11 SCREW
3-362-148-01 SLIDER (PINCH)
3-362-149-01 SLIDER (LIMITTER)
Remark
274
M901
PM902
– 88 –
A-2004-301-A MOTOR ASSY, CONTROL
A-2003-660-A MOTOR ASSY (LOADING)
1-454-522-11 SOLENOID, PLUNGER
Remark
(7) MECHANISM DECK SECTION-2
(DATM-55)
#11
303
M904
305
306
#17
304
307
307
#17
303
#11
302
312
303
309
#9
302
310
301
not supplied
303
306
305
311
Ref. No.
Part No.
Description
* 301
302
303
304
305
1-654-392-11
3-573-470-00
X-3371-518-1
X-3362-028-1
3-341-752-11
S END BOARD
SPRING, COMPRESSION
ROLLER GUIDE ASSY
SLANT BLOCK (L2) ASSY
WASHER, POLYETHYLENE
306
3-362-152-01 SCREW (RETURN GUIDE BOSS)
Remark
Ref. No.
Part No.
Description
307
309
310
311
312
3-912-011-01
3-929-804-01
X-3371-230-1
X-3362-029-1
A-2004-550-A
CATCHER
SPRING,TENSION
LEVER (CLEANER) ASSY
SLANT BLOCK (R2) ASSY
DETECTION (L) ASSY, E
M904
8-848-626-11 DRUM ASSY DOU-03D
– 89 –
Remark
(8) MECHANISM DECK SECTION-3
(DATM-55)
#18
352
352
351
351
353
364
354
#11
365
351
360
359
358
352
362
361
370
M903
356
369
366
351
373
361
361
363
367
M902
357
#11
#11
355
356
370
371
#10
#11
372
#10
351
368
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
351
352
* 353
354
355
3-559-408-11
3-337-622-01
X-3362-030-7
X-3370-186-1
X-3369-705-1
WASHER, POLYETHYLENE, DIA.1.2
ROLLER, RING
CHASSIS ASSY
ARM (RING ROLLER) ASSY
RING (L) ASSY, LOADING
364
365
* 366
* 367
368
X-3371-518-1
3-573-470-00
X-3362-020-1
3-362-156-01
X-3362-204-1
ROLLER GUIDE ASSY
SPRING, COMPRESSION
LEVER (F GUIDE) ASSY
BRACKET (CAPSTAN)
GEAR (LOAD) ASSY
356
* 357
358
359
360
3-362-151-01
A-2007-321-A
3-372-619-01
3-345-181-01
3-362-155-01
BOSS (GUIDE)
DRUM DRIVE BOARD, COMPLETE
GEAR
GEAR (LOADING A)
GEAR (A)
* 369
370
* 371
* 372
373
X-3362-024-1
3-337-653-01
X-3362-025-1
3-929-801-01
3-375-034-01
LEVER (LOADING L) ASSY
SPRING, TENSION
LEVER (LOADING R) ASSY
BRACKET (MD PC BOARD)
SPRING (F GUIDE)
M902
* M903
8-835-306-01 MOTOR, DC U-17A (CAPSTAN)
8-835-205-01 MOTOR, DC U-2A (REEL) (including PM901)
361
362
363
3-701-436-11 WASHER,STOPPER
4-932-338-01 PULLEY (A)
4-913-325-01 BELT, TAKE-UP
Remark
– 90 –
Remark
SECTION 8
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts specified in the diagrams or the components used on
the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when ordering these items.
ANA IN
ANA OUT
• SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. .
uPA. . : µPA. .
uPB. . : µPB. .
uPC. . : µPC. .
uPD. . : µPD. .
The components identified by mark
! or dotted line with mark ! are
critical for safety.
Replace only with part number
specified.
• CAPACITORS
uF: µF
Les composants identifiés par une
marque ! sont critiquens pour la
sécurité.
Ne les remplacer que par une pièce
portant le neméro spécifié.
• COILS
uH: µH
When indicating parts by reference
number, please include the board.
Ref. No.
Part No.
Description
Remark
*
A-2007-651-A ANA IN BOARD, COMPLETE
***********************
Ref. No.
< CAPACITOR >
C131
C132
C133
C231
C232
1-126-051-11
1-126-051-11
1-107-597-11
1-126-051-11
1-126-051-11
ELECT
ELECT
CERAMIC
ELECT
ELECT
47uF
47uF
22PF
47uF
47uF
20%
20%
10%
20%
20%
50V
50V
500V
50V
50V
C233
C376
C377
1-107-597-11 CERAMIC
1-136-165-00 FILM
1-136-165-00 FILM
22PF
0.1uF
0.1uF
10%
5%
5%
500V
50V
50V
Part No.
Description
Remark
R146
R147
R148
R149
R241
1-215-445-00
1-215-421-00
1-215-437-00
1-215-397-00
1-215-445-00
METAL
METAL
METAL
METAL
METAL
10K
1K
4.7K
100
10K
1%
1%
1%
1%
1%
1/4W
1/4W
1/4W
1/4W
1/4W
R242
R243
R244
R245
R246
1-215-445-00
1-215-453-00
1-215-453-00
1-215-445-00
1-215-445-00
METAL
METAL
METAL
METAL
METAL
10K
22K
22K
10K
10K
1%
1%
1%
1%
1%
1/4W
1/4W
1/4W
1/4W
1/4W
R247
R248
R249
1-215-421-00 METAL
1-215-437-00 METAL
1-215-397-00 METAL
1K
4.7K
100
1%
1%
1%
1/4W
1/4W
1/4W
< CONNECTOR >
< VARIABLE RESISTOR >
CN312
1-691-766-21 PLUG (MICRO CONNECTOR) 4P
RV101
1-223-877-11 RES, VAR, CARBON 10K
(ANALOG IN CH-1 (L) LEVEL)
RV201 1-223-877-11 RES, VAR, CARBON 10K
(ANALOG IN CH-2 (R) LEVEL)
************************************************************
< DIODE >
D105
D106
D205
D206
8-719-987-63
8-719-987-63
8-719-987-63
8-719-987-63
DIODE
DIODE
DIODE
DIODE
1N4148M
1N4148M
1N4148M
1N4148M
A-2007-642-A ANA OUT BOARD, COMPLETE
************************
*
< IC >
< CAPACITOR >
IC323
IC324
8-759-981-96 IC RC4560D
8-759-981-96 IC RC4560D
< JACK >
J305
1-750-786-11 CONNECTOR (XLR TYPE) 3P
(ANALOG (BALANCE) IN)
< RESISTOR >
R141
R142
R143
R144
R145
1-215-445-00
1-215-445-00
1-215-453-00
1-215-453-00
1-215-445-00
METAL
METAL
METAL
METAL
METAL
10K
10K
22K
22K
10K
1%
1%
1%
1%
1%
1/4W
1/4W
1/4W
1/4W
1/4W
C134
C135
C136
C137
C138
1-107-597-11
1-126-051-11
1-107-597-11
1-107-597-11
1-126-024-11
CERAMIC
ELECT
CERAMIC
CERAMIC
ELECT
22PF
47uF
22PF
22PF
220uF
10%
20%
10%
10%
20%
500V
50V
500V
500V
25V
C139
C234
C235
C236
C237
1-126-024-11
1-107-597-11
1-126-051-11
1-107-597-11
1-107-597-11
ELECT
CERAMIC
ELECT
CERAMIC
CERAMIC
220uF
22PF
47uF
22PF
22PF
20%
10%
20%
10%
10%
25V
500V
50V
500V
500V
C238
C239
C378
1-126-024-11 ELECT
1-126-024-11 ELECT
1-136-165-00 FILM
220uF
220uF
0.1uF
20%
20%
5%
25V
25V
50V
– 91 –
ANA OUT
Ref. No.
C379
Part No.
DIG IN
DIG OUT
Description
1-136-165-00 FILM
Remark
0.1uF
5%
Ref. No.
Part No.
Description
Remark
50V
< VARIABLE RESISTOR >
RV102
1-223-877-11 RES, VAR, CARBON 10K
(ANALOG OUT CH-1 (L) LEVEL)
RV202 1-223-877-11 RES, VAR, CARBON 10K
(ANALOG OUT CH-2 (R) LEVEL)
************************************************************
< CONNECTOR >
CN311
1-691-766-41 PLUG (MICRO CONNECTOR) 4P
< IC >
IC103
IC104
IC203
IC204
8-759-981-96
8-759-900-72
8-759-981-96
8-759-900-72
IC
IC
IC
IC
RC4560D
NE5532P
RC4560D
NE5532P
< CAPACITOR >
< JACK >
J306
A-2007-643-A DIG IN BOARD, COMPLETE
***********************
*
1-750-785-11 CONNECTOR (XLR TYPE) 3P
(ANALOG (BALANCE) OUT)
C801
C802
C803
C804
C805
1-162-215-31
1-162-215-31
1-136-169-00
1-136-169-00
1-164-159-11
CERAMIC
CERAMIC
FILM
FILM
CERAMIC
C806
1-136-169-00 FILM
47PF
47PF
0.22uF
0.22uF
0.1uF
5%
5%
5%
5%
50V
50V
50V
50V
50V
0.22uF
5%
50V
< RESISTOR >
R150
R151
R152
R153
R154
1-215-421-00
1-215-429-00
1-215-445-00
1-215-445-00
1-215-473-00
METAL
METAL
METAL
METAL
METAL
1K
2.2K
10K
10K
150K
1%
1%
1%
1%
1%
1/4W
1/4W
1/4W
1/4W
1/4W
R156
R157
R158
R160
R161
1-215-453-00
1-215-445-00
1-215-446-00
1-215-457-00
1-215-445-00
METAL
METAL
METAL
METAL
METAL
22K
10K
11K
33K
10K
1%
1%
1%
1%
1%
1/4W
1/4W
1/4W
1/4W
1/4W
R162
R163
R164
R165
R166
1-215-389-00
1-215-389-00
1-215-445-00
1-215-445-00
1-215-469-00
METAL
METAL
METAL
METAL
METAL
47
47
10K
10K
100K
1%
1%
1%
1%
1%
1/4W
1/4W
1/4W
1/4W
1/4W
R167
R250
R251
R252
R253
1-215-469-00
1-215-421-00
1-215-429-00
1-215-445-00
1-215-445-00
METAL
METAL
METAL
METAL
METAL
100K
1K
2.2K
10K
10K
1%
1%
1%
1%
1%
1/4W
1/4W
1/4W
1/4W
1/4W
R254
R256
R257
R258
R260
1-215-473-00
1-215-453-00
1-215-445-00
1-215-446-00
1-215-457-00
METAL
METAL
METAL
METAL
METAL
150K
22K
10K
11K
33K
1%
1%
1%
1%
1%
1/4W
1/4W
1/4W
1/4W
1/4W
R261
R262
R263
R264
R265
1-215-445-00
1-215-389-00
1-215-389-00
1-215-445-00
1-215-445-00
METAL
METAL
METAL
METAL
METAL
10K
47
47
10K
10K
1%
1%
1%
1%
1%
1/4W
1/4W
1/4W
1/4W
1/4W
R266
R267
1-215-469-00 METAL
1-215-469-00 METAL
100K
100K
1%
1%
1/4W
1/4W
< CONNECTOR >
CN806
1-564-510-11 PLUG (MICRO CONNECTOR) 6P
< IC >
IC801
8-759-077-32 IC SN75ALS181N
< JACK >
J801
1-750-788-11 CONNECTOR (XLR TYPE) 3P
(DIGITAL IN AES/EBU)
< RESISTOR >
R801
R802
R803
R804
R805
1-249-409-11
1-249-409-11
1-247-807-31
1-247-807-31
1-249-427-11
CARBON
CARBON
CARBON
CARBON
CARBON
R806
R807
1-249-393-11 CARBON
1-249-393-11 CARBON
220
220
100
100
6.8K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
10
10
5%
5%
1/4W
1/4W
< TRANSFORMER >
T801
1-437-194-21 TRANSFORMER, PULSE
T802
1-437-194-21 TRANSFORMER, PULSE
************************************************************
1-664-494-11 DIG OUT BOARD
*************
*
< CAPACITOR >
C807
C808
C809
C810
– 92 –
1-136-169-00
1-162-215-31
1-162-215-31
1-162-215-31
FILM
CERAMIC
CERAMIC
CERAMIC
0.22uF
47PF
47PF
47PF
5%
5%
5%
5%
50V
50V
50V
50V
DIG OUT
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
< JACK >
1-750-787-11 CONNECTOR (XLR TYPE) 3P
(DIGITAL OUT AES/EBU)
**************************************************************
*
A-2007-647-A DISPLAY BOARD, COMPLETE
************************
*
*
*
3-362-478-01 HOLDER (T), LED
4-932-810-11 CUSHION (FL)
4-947-170-01 HOLDER
C701
C702
C703
C704
C705
1-126-177-11
1-162-294-31
1-164-159-11
1-164-159-11
1-164-159-11
ELECT
CERAMIC
CERAMIC
CERAMIC
CERAMIC
100uF 20%
0.001uF 10%
0.1uF
0.1uF
0.1uF
10V
50V
50V
50V
50V
C706
C707
C708
C709
C710
1-164-159-11
1-164-159-11
1-164-159-11
1-164-159-11
1-164-159-11
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
50V
50V
50V
50V
50V
C711
C712
C713
C714
C715
1-164-159-11
1-164-159-11
1-164-159-11
1-164-159-11
1-164-159-11
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
50V
50V
50V
50V
50V
C716
1-164-159-11 CERAMIC
0.1uF
50V
< CONNECTOR >
1-568-860-11 SOCKET, CONNECTOR 17P
1-564-500-11 PIN, CONNECTOR 7P
< DIODE >
8-719-303-02
8-719-301-52
8-719-301-39
8-719-301-52
LED
LED
LED
LED
SEL2510C-D (PLAY)
SEL2810A-C (PAUSE)
SEL2210S (REC)
SEL2810A-C (MENU)
< FILTER >
FL701
Q701
Q702
Q703
Q704
Q705
8-729-620-05
8-729-620-05
8-729-620-05
8-729-900-80
8-729-900-80
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2603-EF
2SC2603-EF
2SC2603-EF
DTC114ES
DTC114ES
Q706
Q707
8-729-900-80 TRANSISTOR DTC114ES
8-729-900-80 TRANSISTOR DTC114ES
R701
R702
R703
R704
R705
1-249-427-11
1-249-427-11
1-249-427-11
1-249-427-11
1-249-427-11
CARBON
CARBON
CARBON
CARBON
CARBON
6.8K
6.8K
6.8K
6.8K
6.8K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R706
R707
R708
R709
R710
1-249-427-11
1-249-427-11
1-249-427-11
1-249-415-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
6.8K
6.8K
6.8K
680
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R711
R712
R713
R714
R715
1-249-419-11
1-247-843-11
1-249-425-11
1-249-429-11
1-249-435-11
CARBON
CARBON
CARBON
CARBON
CARBON
1.5K
3.3K
4.7K
10K
33K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R716
R717
R718
R719
R720
1-249-415-11
1-249-417-11
1-249-419-11
1-247-843-11
1-249-425-11
CARBON
CARBON
CARBON
CARBON
CARBON
680
1K
1.5K
3.3K
4.7K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R721
R722
R723
R724
R725
1-249-429-11
1-249-435-11
1-249-415-11
1-249-417-11
1-249-419-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
33K
680
1K
1.5K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R726
R727
R730
R731
R732
1-247-843-11
1-249-425-11
1-249-415-11
1-249-417-11
1-249-419-11
CARBON
CARBON
CARBON
CARBON
CARBON
3.3K
4.7K
680
1K
1.5K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R733
R734
R737
R740
R743
1-247-843-11
1-249-425-11
1-249-427-11
1-249-427-11
1-249-427-11
CARBON
CARBON
CARBON
CARBON
CARBON
3.3K
4.7K
6.8K
6.8K
6.8K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R746
R747
1-249-415-11 CARBON
1-249-417-11 CARBON
680
1K
5%
5%
1/4W
1/4W
1-517-382-11 INDICATOR TUBE, FLUORESCENT
< IC >
IC701
IC702
IC703
IC704
IC705
Remark
< RESISTOR >
< CAPACITOR >
D701
D702
D703
D704
Description
< TRANSISTOR >
J802
CN701
* CN702
DISPLAY
8-752-882-29
8-759-995-09
8-759-916-54
8-759-916-12
8-759-373-49
IC
IC
IC
IC
IC
CXP82320-077Q
MSM6338RS
SN74HC174AN
SN74HC00AN
NJL54H400
– 93 –
DISPLAY
Ref. No.
Part No.
Description
Remark
R748
R751
R752
1-249-425-11 CARBON
1-249-421-11 CARBON
1-249-421-11 CARBON
4.7K
2.2K
2.2K
5%
5%
5%
1/4W
1/4W
1/4W
R753
R754
R755
R756
R763
1-249-421-11
1-249-421-11
1-249-421-11
1-249-421-11
1-249-407-11
CARBON
CARBON
CARBON
CARBON
CARBON
2.2K
2.2K
2.2K
2.2K
150
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R764
R765
R766
R769
R770
1-249-407-11
1-249-407-11
1-249-407-11
1-249-429-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
150
150
150
10K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R771
R772
R773
R774
R775
1-249-429-11
1-249-429-11
1-249-417-11
1-249-429-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
10K
1K
10K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R776
R777
R778
R951
R952
1-249-435-11
1-249-417-11
1-249-435-11
1-249-441-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
33K
1K
33K
100K
100K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R953
R954
R955
R956
R957
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R958
R959
R960
R961
R962
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R963
R964
R965
R966
R967
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R968
R969
R970
R971
R972
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R973
R974
R975
R976
R977
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R978
1-249-441-11 CARBON
100K
5%
1/4W
Ref. No.
Part No.
Description
Remark
R979
R980
R981
R982
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
100K
100K
100K
100K
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
R983
R984
R985
R986
R987
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R988
R989
R990
1-249-441-11 CARBON
1-249-441-11 CARBON
1-249-441-11 CARBON
100K
100K
100K
5%
5%
5%
1/4W
1/4W
1/4W
< SWITCH >
S701
S702
S703
S704
S705
1-554-937-11
1-554-937-11
1-554-937-11
1-554-937-11
1-554-937-11
SWITCH, KEY BOARD (REW)
SWITCH, KEY BOARD (FF)
SWITCH, KEY BOARD (REC)
SWITCH, KEY BOARD (PAUSE)
SWITCH, KEY BOARD (REC MUTE)
S706
S707
S708
S709
S710
1-554-937-11
1-554-937-11
1-554-937-11
1-554-937-11
1-554-937-11
SWITCH, KEY BOARD (MENU)
SWITCH, KEY BOARD (SET)
SWITCH, KEY BOARD (OPEN/CLOSE)
SWITCH, KEY BOARD (STOP)
SWITCH, KEY BOARD (PLAY)
S711
S712
S713
S714
S715
1-554-937-11
1-554-937-11
1-554-937-11
1-554-937-11
1-554-937-11
SWITCH, KEY BOARD (PREVIOUS)
SWITCH, KEY BOARD (NEXT)
SWITCH, KEY BOARD (MARK)
SWITCH, KEY BOARD (SKIP PLAY)
SWITCH, KEY BOARD (LOCATE)
S716
S717
S718
S719
S720
1-554-937-11
1-554-937-11
1-554-937-11
1-554-937-11
1-554-937-11
SWITCH, KEY BOARD (REPEAT)
SWITCH, KEY BOARD (ERASE-START ID)
SWITCH, KEY BOARD (WRITE-START ID)
SWITCH, KEY BOARD (REHEARSAL-START ID)
SWITCH, KEY BOARD (AUTO-START ID)
S723
S724
S725
S726
S727
1-554-937-11
1-554-937-11
1-554-937-11
1-554-937-11
1-554-937-11
SWITCH, KEY BOARD (ERASE-SKIP ID)
SWITCH, KEY BOARD (WRITE-SKIP ID)
SWITCH, KEY BOARD (REHEARSAL-SKIP ID)
SWITCH, KEY BOARD (RENUMBER)
SWITCH, KEY BOARD (MODE)
S728
S729
1-554-937-11 SWITCH, KEY BOARD (COUNTER RESET)
1-554-937-11 SWITCH, KEY BOARD (MARGIN RESET)
< VIBRATOR >
X701
1-577-359-21 VIBRATOR, CERAMIC (4.19MHz)
**************************************************************
– 94 –
DRUM DRIVE
Ref. No.
Part No.
Description
Remark
*
A-2007-321-A DRUM DRIVE BOARD, COMPLETE
**************************
Ref. No.
< CAPACITOR >
C1
C3
C5
C6
C7
1-124-257-00
1-162-306-11
1-126-923-11
1-126-923-11
1-126-923-11
ELECT
CERAMIC
ELECT
ELECT
ELECT
2.2uF
0.01uF
220uF
220uF
220uF
20%
20%
20%
20%
20%
50V
16V
10V
10V
10V
C8
C9
C10
C11
C12
1-162-302-11
1-162-302-11
1-162-286-31
1-162-302-11
1-162-302-11
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
0.0022uF 30%
0.0022uF 30%
220PF 10%
0.0022uF 30%
0.0022uF 30%
16V
16V
50V
16V
16V
C13
C14
C15
1-126-096-11 ELECT
1-126-923-11 ELECT
1-162-306-11 CERAMIC
10uF
220uF
0.01uF
35V
10V
16V
< CONNECTOR >
* CN1
CN2
CN3
* CN4
* CN5
1-568-845-11
1-691-461-11
1-564-505-11
1-564-704-11
1-564-515-11
SOCKET, CONNECTOR 31P
PIN, CONNECTOR (PC BOARD) 5P
PLUG, CONNECTOR 2P
PIN, CONNECTOR (SMALL TYPE) 2P
PLUG, CONNECTOR 12P
CN6
CN7
CN8
CN9
1-691-465-11
1-568-369-11
1-506-503-11
1-564-337-00
PIN, CONNECTOR (PC BOARD) 9P
HOUSING, CONNECTOR (PC BOARD) 8P
PIN, CONNECTOR 9P
PIN, CONNECTOR 3P
*
*
*
*
* CN11
* CN12
D2
D3
8-719-200-82 DIODE 11ES2
8-719-200-82 DIODE 11ES2
Remark
R1
R2
R3
R4
R5
1-247-843-11
1-249-429-11
1-249-407-11
1-247-843-11
1-249-421-11
CARBON
CARBON
CARBON
CARBON
CARBON
3.3K
10K
150
3.3K
2.2K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R6
R7
R8
R9
R11
1-249-435-11
1-247-807-31
1-249-417-11
1-249-429-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
33K
100
1K
10K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R12
R14
R15
R16
R17
1-249-417-11
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R18
R19
R20
R21
R22
1-249-409-11
1-249-409-11
1-249-401-11
1-249-429-11
1-249-433-11
CARBON
CARBON
CARBON
CARBON
CARBON
220
220
47
10K
22K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R23
1-249-403-11 CARBON
68
5%
1/4W
R24
1-249-403-11 CARBON
68
5%
1/4W
R25
1-247-843-11 CARBON
3.3K
5%
1/4W
R26
1-247-843-11 CARBON
3.3K
5%
1/4W
R27
1-249-419-11 CARBON
1.5K
5%
1/4W
**************************************************************
1-664-486-11 HP BOARD
********
*
1-564-337-61 PIN, CONNECTOR 3P
1-564-336-00 PIN, CONNECTOR 2P
< DIODE >
Description
< RESISTOR >
1-537-770-21 TERMINAL BOARD, GROUND
20%
20%
20%
Part No.
HP
< CAPACITOR >
C122
C222
C374
C375
1-102-114-00
1-102-114-00
1-126-024-11
1-126-024-11
CERAMIC
CERAMIC
ELECT
ELECT
470PF
470PF
220uF
220uF
10%
10%
20%
20%
50V
50V
25V
25V
< CONNECTOR >
< IC >
CN320
IC1
IC2
IC3
8-759-135-80 IC uPC358C
8-759-633-65 IC M54641L
8-752-060-73 IC CX20115A-T4
< TRANSISTOR >
Q1
Q2
Q3
8-729-620-05 TRANSISTOR 2SC2603-EF
8-729-801-84 TRANSISTOR 2SB1013-4
8-729-801-93 TRANSISTOR 2SD1387
1-691-768-11 PLUG (MICRO CONNECTOR) 6P
< FUSIBLE >
! FR301
! FR302
1-212-857-00 FUSIBLE
1-212-857-00 FUSIBLE
10
10
5%
5%
1/4W F
1/4W F
< IC >
IC321
– 95 –
8-759-981-96 IC RC4560D
The components identified by
mark ! or dotted line with
mark ! are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque ! sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le neméro spécifié.
HP
Ref. No.
INPUT SW
Part No.
LOAD SW
Description
LOADING MOTOR
Remark
< JACK >
J304
MAIN (AUDIO, DIGITAL)
Ref. No.
Part No.
Description
Remark
*
1-655-286-11 LOADING MOTOR BOARD
*********************
1-565-327-11 JACK, LARGE TYPE 1P (PHONES)
< CAPACITOR >
< COIL >
C999
L101
L201
1-410-386-41 INDUCTOR, FERITE-BEAD
1-410-386-41 INDUCTOR, FERITE-BEAD
1-136-165-00 FILM
0.45uH
0.45uH
R132
R133
R134
R135
R232
1-249-435-11
1-249-433-11
1-249-425-11
1-247-807-31
1-249-435-11
CARBON
CARBON
CARBON
CARBON
CARBON
33K
22K
4.7K
100
33K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R233
R234
R235
1-249-433-11 CARBON
1-249-425-11 CARBON
1-247-807-31 CARBON
22K
4.7K
100
5%
5%
5%
1/4W
1/4W
1/4W
A-2007-648-A MAIN BOARD, COMPLETE
*********************
(including AUDIO board, DIGITAL board)
*
1-533-293-11
1-550-414-21
2-259-121-01
3-309-144-21
7-685-871-01
*
RV302 1-225-374-11 RES, VAR, CARBON 20K/20K (PHONE LEVEL)
***********************************************************
1-664-484-11 INPUT SW BOARD
**************
< CONNECTOR >
1-249-431-11
1-249-431-11
1-249-435-11
1-249-431-11
1-249-431-11
CARBON
CARBON
CARBON
CARBON
CARBON
15K
15K
33K
15K
15K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
< SWITCH >
S732
1-572-269-11 SWITCH, SLIDE (INPUT)
S733
1-572-269-11 SWITCH, SLIDE (ANALOG INPUT)
S734
1-572-268-11 SWITCH, SLIDE (REC MODE)
S735
1-572-269-11 SWITCH, SLIDE (SBM)
************************************************************
*
FUSE HOLDER
HOLDER, BATTERY
SCREW, TR
HEAT SINC
SCREW +BVTT 3X6 (S)
< CAPACITOR >
C102
C104
C105
C106
C107
1-126-023-11
1-130-481-00
1-126-023-11
1-136-165-00
1-136-165-00
ELECT
MYLAR
ELECT
FILM
FILM
100uF 20%
0.0068uF 5%
100uF 20%
0.1uF
5%
0.1uF
5%
25V
50V
25V
50V
50V
C108
C109
C110
C111
C112
1-136-165-00
1-136-165-00
1-106-343-00
1-130-467-00
1-130-467-00
FILM
FILM
MYLAR
MYLAR
MYLAR
0.1uF
0.1uF
1000PF
470PF
470PF
5%
5%
5%
5%
5%
50V
50V
200V
50V
50V
C113
C114
C115
C116
C117
1-110-339-11
1-110-339-11
1-106-359-00
1-106-343-00
1-126-023-11
MYLAR
MYLAR
MYLAR
MYLAR
ELECT
220PF
220PF
4700PF
1000PF
100uF
5%
5%
5%
5%
20%
50V
50V
200V
200V
25V
C118
C119
C123
C140
C202
1-136-165-00
1-136-165-00
1-126-023-11
1-126-024-11
1-126-023-11
FILM
FILM
ELECT
ELECT
ELECT
0.1uF
0.1uF
100uF
220uF
100uF
5%
5%
20%
20%
20%
50V
50V
25V
25V
25V
C204
C205
C206
C207
C208
1-130-481-00
1-126-023-11
1-136-165-00
1-136-165-00
1-136-165-00
MYLAR
ELECT
FILM
FILM
FILM
0.0068uF 5%
100uF 20%
0.1uF
5%
0.1uF
5%
0.1uF
5%
50V
25V
50V
50V
50V
C209
C210
1-136-165-00 FILM
1-106-343-00 MYLAR
0.1uF
5%
1000PF 5%
50V
200V
1-564-339-00 PIN, CONNECTOR 5P
< RESISTOR >
R738
R741
R742
R744
R749
50V
* CN919 1-564-496-11 PIN, CONNECTOR 3P
* CN920 1-564-497-11 PIN, CONNECTOR 4P
**************************************************************
< VARIABLE RESISTOR >
* CN704
5%
< CONNECTOR >
< RESISTOR >
*
0.1uF
1-655-285-11 LOAD SW BOARD
*************
< SWITCH >
S902
1-571-489-11 SWITCH, SLIDE (UNLOAD)
S903
1-571-489-11 SWITCH, SLIDE (LOAD)
************************************************************
– 96 –
MAIN (AUDIO, DIGITAL)
Ref. No.
Part No.
Description
Remark
C211
C212
C213
1-130-467-00 MYLAR
1-130-467-00 MYLAR
1-110-339-11 MYLAR
470PF
470PF
220PF
5%
5%
5%
50V
50V
50V
C214
C215
C216
C217
C218
1-110-339-11
1-106-359-00
1-106-343-00
1-126-023-11
1-136-165-00
MYLAR
MYLAR
MYLAR
ELECT
FILM
220PF
4700PF
1000PF
100uF
0.1uF
5%
5%
5%
20%
5%
50V
200V
200V
25V
50V
C219
C223
C240
C301
C302
1-136-165-00
1-126-023-11
1-126-024-11
1-124-997-11
1-124-997-11
FILM
ELECT
ELECT
ELECT
ELECT
0.1uF
100uF
220uF
470uF
470uF
5%
20%
20%
20%
20%
50V
25V
25V
10V
10V
C303
C304
C305
C306
C307
1-136-165-00
1-136-165-00
1-136-165-00
1-126-023-11
1-136-165-00
FILM
FILM
FILM
ELECT
FILM
0.1uF
0.1uF
0.1uF
100uF
0.1uF
5%
5%
5%
20%
5%
50V
50V
50V
25V
50V
C308
C309
C310
C311
C312
1-126-023-11
1-162-294-31
1-162-294-31
1-164-159-11
1-124-997-11
ELECT
CERAMIC
CERAMIC
CERAMIC
ELECT
100uF
0.001uF
0.001uF
0.1uF
470uF
20%
10%
10%
25V
50V
50V
50V
10V
C313
C314
C315
C316
C317
1-136-165-00
1-164-159-11
1-162-195-31
1-162-195-31
1-162-196-31
FILM
CERAMIC
CERAMIC
CERAMIC
CERAMIC
0.1uF
0.1uF
4.7PF
4.7PF
5.6PF
5%
C318
C319
C320
C321
C322
1-162-196-31
1-164-159-11
1-124-564-11
1-124-564-11
1-136-165-00
CERAMIC
CERAMIC
ELECT
ELECT
FILM
5.6PF
0.1uF
4700uF
4700uF
0.1uF
10%
20%
20%
5%
50V
50V
25V
25V
50V
C323
C324
C325
C326
C327
1-136-165-00
1-126-027-11
1-126-027-11
1-124-997-11
1-136-165-00
FILM
ELECT
ELECT
ELECT
FILM
0.1uF
1000uF
1000uF
470uF
0.1uF
5%
20%
20%
20%
5%
50V
25V
25V
10V
50V
C328
C329
C330
C331
C332
1-126-023-11
1-136-165-00
1-126-023-11
1-136-165-00
1-136-165-00
ELECT
FILM
ELECT
FILM
FILM
100uF
0.1uF
100uF
0.1uF
0.1uF
20%
5%
20%
5%
5%
25V
50V
25V
50V
50V
C333
C334
C335
C337
C338
1-126-013-11
1-162-294-31
1-162-294-31
1-164-159-11
1-126-023-11
ELECT
CERAMIC
CERAMIC
CERAMIC
ELECT
1000uF
0.001uF
0.001uF
0.1uF
100uF
20%
10%
10%
16V
50V
50V
50V
25V
20%
10%
10%
10%
20%
50V
50V
50V
50V
50V
Ref. No.
Part No.
Description
C339
C340
C341
C342
C343
1-164-159-11
1-136-169-00
1-136-153-00
1-162-219-31
1-162-199-31
CERAMIC
FILM
FILM
CERAMIC
CERAMIC
0.1uF
0.22uF
0.01uF
68PF
10PF
C344
C345
C346
C347
C348
1-162-199-31
1-126-048-81
1-164-159-11
1-162-215-31
1-136-161-00
CERAMIC
ELECT
CERAMIC
CERAMIC
FILM
10PF
10uF
0.1uF
47PF
0.047uF
C350
C351
C352
C353
C356
1-126-026-11
1-126-026-11
1-164-159-11
1-164-159-11
1-164-159-11
ELECT
ELECT
CERAMIC
CERAMIC
CERAMIC
470uF
470uF
0.1uF
0.1uF
0.1uF
20%
20%
25V
25V
50V
50V
50V
C359
C360
C364
C369
C370
1-126-025-11
1-126-025-11
1-164-159-11
1-164-159-11
1-164-159-11
ELECT
ELECT
CERAMIC
CERAMIC
CERAMIC
330uF
330uF
0.1uF
0.1uF
0.1uF
20%
20%
16V
16V
50V
50V
50V
C371
C372
C501
C502
C503
1-164-159-11
1-164-159-11
1-126-017-11
1-126-946-11
1-126-927-11
CERAMIC
CERAMIC
ELECT
ELECT
ELECT
0.1uF
0.1uF
6800uF 20%
6800uF 20%
2200uF 20%
50V
50V
16V
25V
10V
C504
C505
C506
C507
C508
1-126-926-11
1-126-925-11
1-126-925-11
1-164-159-11
1-128-553-11
ELECT
ELECT
ELECT
CERAMIC
ELECT
1000uF
470uF
470uF
0.1uF
220uF
20%
10V
10V
10V
50V
63V
C509
C510
C511
C512
C513
1-126-968-11
1-164-159-11
1-164-159-11
1-162-294-31
1-162-302-11
ELECT
CERAMIC
CERAMIC
CERAMIC
CERAMIC
100uF 20%
0.1uF
0.1uF
0.001uF 10%
0.0022uF 30%
50V
50V
50V
50V
16V
C514
C515
C516
C517
C518
1-162-286-31
1-162-294-31
1-162-302-11
1-162-286-31
1-162-306-11
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
220PF 10%
0.001uF 10%
0.0022uF 30%
220PF 10%
0.01uF 20%
50V
50V
16V
50V
16V
C519
C520
C521
C522
C523
1-162-306-11
1-162-290-31
1-162-306-11
1-126-965-11
1-162-306-11
CERAMIC
CERAMIC
CERAMIC
ELECT
CERAMIC
0.01uF
470PF
0.01uF
22uF
0.01uF
20%
10%
20%
20%
20%
16V
50V
16V
50V
16V
C524
C525
C526
C527
1-162-290-31
1-162-306-11
1-126-965-11
1-164-159-11
CERAMIC
CERAMIC
ELECT
CERAMIC
470PF
0.01uF
22uF
0.1uF
10%
20%
20%
50V
16V
50V
50V
– 97 –
Remark
5%
5%
5%
5%
5%
20%
5%
5%
20%
20%
20%
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
MAIN (AUDIO, DIGITAL)
Ref. No.
Part No.
Description
Remark
C528
1-164-159-11 CERAMIC
0.1uF
50V
C529
C530
C531
C532
C533
1-126-925-11
1-162-294-31
1-126-961-11
1-164-159-11
1-162-203-31
ELECT
CERAMIC
ELECT
CERAMIC
CERAMIC
470uF
0.001uF
2.2uF
0.1uF
15PF
20%
10%
20%
C534
C535
C536
C537
C538
1-162-203-31
1-164-159-11
1-136-165-00
1-126-925-11
1-164-159-11
CERAMIC
CERAMIC
FILM
ELECT
CERAMIC
15PF
0.1uF
0.1uF
470uF
0.1uF
5%
C539
C540
C541
C542
C543
1-162-306-11
1-162-294-31
1-162-284-31
1-164-159-11
1-126-925-11
CERAMIC
CERAMIC
CERAMIC
CERAMIC
ELECT
0.01uF
0.001uF
150PF
0.1uF
470uF
20%
10%
10%
20%
16V
50V
50V
50V
10V
C544
C545
C546
C547
C548
1-162-294-31
1-162-294-31
1-162-294-31
1-162-294-31
1-162-294-31
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
0.001uF
0.001uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C549
C550
C552
C553
C554
1-162-294-31
1-164-159-11
1-162-207-31
1-162-207-31
1-162-203-31
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
0.001uF
0.1uF
22PF
22PF
15PF
10%
50V
50V
50V
50V
50V
C555
C556
C557
C558
C559
1-162-203-31
1-164-159-11
1-164-159-11
1-164-159-11
1-136-153-00
CERAMIC
CERAMIC
CERAMIC
CERAMIC
FILM
15PF
0.1uF
0.1uF
0.1uF
0.01uF
5%
5%
50V
50V
50V
50V
50V
C560
C561
C562
C563
C564
1-164-159-11
1-162-211-31
1-136-153-00
1-126-965-11
1-136-153-00
CERAMIC
CERAMIC
FILM
ELECT
FILM
0.1uF
33PF
0.01uF
22uF
0.01uF
5%
5%
20%
5%
50V
50V
50V
50V
50V
C565
C566
C568
C573
C575
1-162-282-31
1-164-159-11
1-164-159-11
1-162-179-11
1-164-159-11
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
100PF
0.1uF
0.1uF
0.1uF
0.1uF
C576
C578
C579
C580
C581
1-164-159-11
1-164-159-11
1-164-159-11
1-162-203-31
1-162-205-31
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
0.1uF
0.1uF
0.1uF
15PF
18PF
C582
C583
1-164-159-11 CERAMIC
1-162-600-11 CERAMIC
5%
5%
20%
5%
5%
5%
10%
5%
5%
0.1uF
0.0047uF 20%
10V
50V
50V
50V
50V
50V
50V
50V
10V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
50V
16V
Ref. No.
C584
C585
Part No.
Description
1-162-600-11 CERAMIC
1-162-294-31 CERAMIC
Remark
0.0047uF 20%
0.001uF 10%
< CONNECTOR >
CN302
CN303
CN304
CN305
CN307
1-691-766-31
1-691-766-11
1-691-768-11
1-691-765-11
1-691-765-11
PLUG (MICRO CONNECTOR) 4P
PLUG (MICRO CONNECTOR) 4P
PLUG (MICRO CONNECTOR) 6P
PLUG (MICRO CONNECTOR) 3P
PLUG (MICRO CONNECTOR) 3P
CN308
CN501
CN502
* CN504
* CN505
1-691-765-21
1-691-767-11
1-691-766-11
1-568-845-11
1-568-836-11
PLUG (MICRO CONNECTOR) 3P
PLUG (MICRO CONNECTOR) 5P
PLUG (MICRO CONNECTOR) 4P
SOCKET, CONNECTOR 31P
SOCKET, CONNECTOR 17P
CN506
CN507
* CN508
CN509
CN510
1-770-164-11
1-691-461-11
1-564-339-00
1-691-765-31
1-691-765-41
PIN, CONNECTOR (PC BOARD) 15P
PIN, CONNECTOR (PC BOARD) 5P
PIN, CONNECTOR 5P
PLUG (MICRO CONNECTOR) 3P
PLUG (MICRO CONNECTOR) 3P
CN511
CN512
1-691-765-21 PLUG (MICRO CONNECTOR) 3P
1-691-768-31 PLUG (MICRO CONNECTOR) 6P
< DIODE >
D101
D102
D103
D104
D201
8-719-987-63
8-719-987-63
8-719-987-63
8-719-987-63
8-719-987-63
DIODE
DIODE
DIODE
DIODE
DIODE
1N4148M
1N4148M
1N4148M
1N4148M
1N4148M
D202
D203
D204
D301
D302
8-719-987-63
8-719-987-63
8-719-987-63
8-719-230-02
8-719-230-02
DIODE
DIODE
DIODE
DIODE
DIODE
1N4148M
1N4148M
1N4148M
30DF2
30DF2
D303
D304
D305
D306
D307
8-719-230-02
8-719-230-02
8-719-987-63
8-719-987-63
8-719-987-63
DIODE
DIODE
DIODE
DIODE
DIODE
30DF2
30DF2
1N4148M
1N4148M
1N4148M
D308
D313
D314
D317
D501
8-719-976-30
8-719-987-63
8-719-987-63
8-719-987-63
8-719-312-47
DIODE
DIODE
DIODE
DIODE
DIODE
KV1560N
1N4148M
1N4148M
1N4148M
RBA-406B
D502
D503
D504
D505
D506
8-719-312-47
8-719-200-77
8-719-015-13
8-719-200-77
8-719-200-77
DIODE
DIODE
DIODE
DIODE
DIODE
RBA-406B
10E2N
UZP-9.1BC-TP
10E2N
10E2N
– 98 –
16V
50V
MAIN (AUDIO, DIGITAL)
Ref. No.
Part No.
Description
Remark
D507
D508
D509
D510
D511
8-719-985-57
8-719-987-63
8-719-987-63
8-719-200-77
8-719-911-06
DIODE
DIODE
DIODE
DIODE
DIODE
D512
D513
8-719-911-06 DIODE 1SS106
8-719-045-72 DIODE KV1550NT
HZS4BLL-TA
1N4148M
1N4148M
10E2N
1SS106
< FUSE >
! F501
! F501
! F502
! F502
1-532-464-51
1-576-105-11
1-532-464-51
1-576-105-11
FUSE, TIME-LAG (2.5A/250V) (AEP)
FUSE (2.5A/250V) (US, Canadian)
FUSE, TIME-LAG (2.5A/250V) (AEP)
FUSE (2.5A/250V) (US, Canadian)
< FUSIBLE >
! FR304
! FR305
! FR501
! FR502
1-219-139-11
1-219-139-11
1-219-136-11
1-212-873-11
FUSIBLE
FUSIBLE
FUSIBLE
FUSIBLE
0.68
0.68
0.22
47
10%
10%
10%
5%
1/4W F
1/4W F
1/4W F
1/4W F
< IC >
IC101
IC102
IC201
IC202
IC301
8-759-900-72
8-759-900-72
8-759-900-72
8-759-900-72
8-759-231-58
IC
IC
IC
IC
IC
NE5532P
NE5532P
NE5532P
NE5532P
TA7812S
IC302
IC303
IC304
IC305
IC306
8-759-245-86
8-759-602-83
8-759-602-83
8-759-602-67
8-759-189-33
IC
IC
IC
IC
IC
TA7912S
M5238P
M5238P
M5278L05
M5279L05-TP
IC307
IC308
IC309
IC310
IC311
8-759-330-53
8-759-196-21
8-759-925-90
8-759-269-92
8-759-269-92
IC
IC
IC
IC
IC
CXD8493M-E1
CXD8482Q
SN74HC74ANS
SN74HCU04ANS-E20
SN74HCU04ANS-E20
IC312
IC313
IC314
IC315
IC316
8-759-926-95
8-759-270-50
8-759-370-62
8-759-250-81
8-759-094-53
IC
IC
IC
IC
IC
SN74HC4020NS
SN74HC368ANS-E20
CXD8505BQ
TC5081AP
TA7805S
IC317
IC318
IC319
IC320
IC325
8-759-094-53
8-759-602-67
8-759-231-58
8-759-245-86
8-759-242-72
IC
IC
IC
IC
IC
TA7805S
M5278L05
TA7812S
TA7912S
TC7W00F
IC501
IC502
IC503
8-752-882-30 IC CXP87540-033Q
8-752-882-31 IC CXP87532-034Q
8-752-355-55 IC CXD2605Q
Ref. No.
Part No.
Description
Remark
IC504
IC508
8-752-364-95 IC CXK58257BM-10LL-T6
8-759-927-72 IC TL1591CP
IC509
IC510
IC511
IC512
IC513
8-759-701-01
8-759-927-72
8-759-926-17
8-759-007-80
8-759-269-92
IC
IC
IC
IC
IC
NJM2904M
TL1591CP
SN74HC153ANS
MC74HC175F
SN74HCU04ANS-E20
IC514
IC515
IC516
IC517
IC518
8-759-927-72
8-759-927-72
8-759-634-43
8-759-426-52
8-759-333-82
IC
IC
IC
IC
IC
TL1591CP
TL1591CP
M51953BFP
AT24C01A-10SC-TP-B
MSM6782-01MS-K-R1
IC519
IC520
IC521
IC522
IC523
8-759-925-90
8-759-701-01
8-759-701-01
8-759-701-01
8-759-633-65
IC
IC
IC
IC
IC
SN74HC74ANS
NJM2904M
NJM2904M
NJM2904M
M54641L
< JACK >
J501
1-770-162-21 JACK, PIN 2P
(DIGITAL IN/OUT COAXIAL/AES/EBU)
< COIL >
L301
L302
L303
L304
L305
1-410-509-11
1-410-509-11
1-410-509-11
1-410-509-11
1-410-509-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
10uH
10uH
10uH
10uH
10uH
L306
L307
L308
L309
L310
1-410-509-11
1-426-850-11
1-410-397-21
1-410-397-21
1-410-509-11
INDUCTOR
10uH
COIL (RF)
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
INDUCTOR
10uH
L311
L312
L501
L502
L503
1-410-509-11
1-410-509-11
1-410-509-11
1-410-509-11
1-410-509-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
10uH
10uH
10uH
10uH
10uH
L504
L506
1-410-498-11 INDUCTOR
1-410-509-11 INDUCTOR
1.2uH
10uH
< TERMINAL >
LUG301
LUG302
LUG304
LUG503
– 99 –
1-537-770-21
1-537-770-21
1-537-770-21
1-537-770-21
TERMINAL BOARD, GROUND
TERMINAL BOARD, GROUND
TERMINAL BOARD, GROUND
TERMINAL BOARD, GROUND
The components identified by
mark ! or dotted line with
mark ! are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque ! sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le neméro spécifié.
MAIN (AUDIO, DIGITAL)
Ref. No.
Part No.
Description
Remark
< TRANSISTOR >
Q101
Q102
Q303
Q304
Q305
8-729-107-85
8-729-107-85
8-729-900-80
8-729-620-05
8-729-620-05
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC3623A-K
2SC3623A-K
DTC114ES
2SC2603-EF
2SC2603-EF
Q306
Q307
Q308
Q309
Q310
8-729-620-05
8-729-200-56
8-729-200-56
8-729-422-57
8-729-900-80
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2603-EF
2SK241-GR
2SK241-GR
UN4111
DTC114ES
Q311
Q312
Q501
Q502
Q503
8-729-900-80
8-729-900-80
8-729-620-05
8-729-119-76
8-729-140-97
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114ES
DTC114ES
2SC2603-EF
2SA1175-HFE
2SB734-34
Q504
Q505
Q506
Q507
Q508
8-729-927-11
8-729-927-12
8-729-927-11
8-729-927-12
8-729-900-80
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1585SQR
2SC4115SQR
2SA1585SQR
2SC4115SQR
DTC114ES
Q509
Q510
Q511
Q512
Q513
8-729-900-80
8-729-900-80
8-729-900-80
8-729-141-83
8-729-119-76
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114ES
DTC114ES
DTC114ES
2SB1094-LK
2SA1175-HFE
Q514
Q515
Q516
Q517
Q518
8-729-620-05
8-729-141-83
8-729-119-76
8-729-620-05
8-729-620-05
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2603-EF
2SB1094-LK
2SA1175-HFE
2SC2603-EF
2SC2603-EF
Q519
Q520
Q521
Q522
Q524
8-729-620-05
8-729-900-80
8-729-620-05
8-729-900-80
8-729-900-80
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2603-EF
DTC114ES
2SC2603-EF
DTC114ES
DTC114ES
< RESISTOR >
R102
R106
R107
R108
R109
1-249-441-11
1-249-429-11
1-249-433-11
1-249-425-11
1-249-425-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
10K
22K
4.7K
4.7K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R110
R111
R112
R113
R114
1-249-401-11
1-249-401-11
1-259-444-11
1-259-444-11
1-259-444-11
CARBON
CARBON
CARBON
CARBON
CARBON
47
47
4.7K
4.7K
4.7K
5%
5%
1%
1%
1%
1/4W
1/4W
1/6W
1/6W
1/6W
Ref. No.
Part No.
Description
R115
R116
R117
R118
R119
1-259-444-11
1-259-432-11
1-259-432-11
1-259-444-11
1-259-444-11
CARBON
CARBON
CARBON
CARBON
CARBON
4.7K
1.5K
1.5K
4.7K
4.7K
1%
1%
1%
1%
1%
1/6W
1/6W
1/6W
1/6W
1/6W
R120
R121
R122
R123
R124
1-259-436-11
1-259-436-11
1-259-436-11
1-259-436-11
1-249-419-11
CARBON
CARBON
CARBON
CARBON
CARBON
2.2K
2.2K
2.2K
2.2K
1.5K
1%
1%
1%
1%
5%
1/6W
1/6W
1/6W
1/6W
1/4W
R125
R126
R127
R128
R129
1-249-419-11
1-249-441-11
1-249-407-11
1-249-407-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
1.5K
100K
150
150
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R202
R206
R207
R208
R209
1-249-441-11
1-249-429-11
1-249-433-11
1-249-425-11
1-249-425-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
10K
22K
4.7K
4.7K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R210
R211
R212
R213
R214
1-249-401-11
1-249-401-11
1-259-444-11
1-259-444-11
1-259-444-11
CARBON
CARBON
CARBON
CARBON
CARBON
47
47
4.7K
4.7K
4.7K
5%
5%
1%
1%
1%
1/4W
1/4W
1/6W
1/6W
1/6W
R215
R216
R217
R218
R219
1-259-444-11
1-259-432-11
1-259-432-11
1-259-444-11
1-259-444-11
CARBON
CARBON
CARBON
CARBON
CARBON
4.7K
1.5K
1.5K
4.7K
4.7K
1%
1%
1%
1%
1%
1/6W
1/6W
1/6W
1/6W
1/6W
R220
R221
R222
R223
R224
1-259-436-11
1-259-436-11
1-259-436-11
1-259-436-11
1-249-419-11
CARBON
CARBON
CARBON
CARBON
CARBON
2.2K
2.2K
2.2K
2.2K
1.5K
1%
1%
1%
1%
5%
1/6W
1/6W
1/6W
1/6W
1/4W
R225
R226
R227
R228
R229
1-249-419-11
1-249-441-11
1-249-407-11
1-249-407-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
1.5K
100K
150
150
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R303
R304
R305
R306
R307
1-249-429-11
1-249-413-11
1-249-413-11
1-249-417-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
470
470
1K
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R308
R309
R310
R311
1-249-417-11
1-249-413-11
1-249-441-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
1K
470
100K
1K
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
– 100 –
Remark
MAIN (AUDIO, DIGITAL)
Ref. No.
Part No.
Description
Remark
R312
1-247-903-00 CARBON
1M
5%
1/4W
R313
R314
R315
R316
R317
1-249-407-11
1-249-441-11
1-249-417-11
1-247-903-00
1-249-407-11
CARBON
CARBON
CARBON
CARBON
CARBON
150
100K
1K
1M
150
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R320
R321
R322
R323
R324
1-249-411-11
1-249-417-11
1-249-441-11
1-249-409-11
1-249-409-11
CARBON
CARBON
CARBON
CARBON
CARBON
330
1K
100K
220
220
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R325
R326
R327
R328
R329
1-249-413-11
1-249-413-11
1-249-413-11
1-249-425-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
470
470
470
4.7K
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R330
R331
R332
R333
R334
1-249-401-11
1-249-417-11
1-249-429-11
1-249-421-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
47
1K
10K
2.2K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R335
R336
R337
R338
R339
1-249-429-11
1-249-428-11
1-249-441-11
1-249-417-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
8.2K
100K
1K
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R340
R341
R342
R343
R345
1-249-417-11
1-247-895-00
1-249-437-11
1-249-441-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
470K
47K
100K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R348
R349
R350
R351
R352
1-249-409-11
1-249-409-11
1-249-411-11
1-249-413-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
220
220
330
470
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R353
R354
R501
R502
R503
1-249-417-11
1-249-417-11
1-249-425-11
1-249-429-11
1-249-421-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
1K
4.7K
10K
2.2K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R504
R505
R506
R507
R508
1-249-433-11
1-247-843-11
1-249-413-11
1-249-429-11
1-249-409-11
CARBON
CARBON
CARBON
CARBON
CARBON
22K
3.3K
470
10K
220
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R509
1-249-409-11 CARBON
220
5%
1/4W
Ref. No.
Part No.
Description
R510
R511
R512
R513
1-249-409-11
1-249-409-11
1-249-441-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
220
220
100K
100K
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
R514
R515
R516
R517
R518
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R519
R520
R522
R523
R524
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
100K
100K
100K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R525
R526
R527
R528
R529
1-249-417-11
1-249-429-11
1-247-807-31
1-249-417-11
1-249-409-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
10K
100
1K
220
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R530
R531
R532
R533
R534
1-249-441-11
1-249-441-11
1-249-429-11
1-249-417-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
100K
10K
1K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R535
R536
R537
R539
R540
1-247-807-31
1-249-417-11
1-249-409-11
1-249-409-11
1-249-409-11
CARBON
CARBON
CARBON
CARBON
CARBON
100
1K
220
220
220
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R541
R544
R545
R546
R547
1-249-441-11
1-249-441-11
1-249-429-11
1-249-429-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
100K
10K
10K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R548
R549
R550
R551
R552
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
100K
100K
100K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R553
R554
R555
R556
R557
1-249-425-11
1-249-425-11
1-249-429-11
1-249-429-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
4.7K
4.7K
10K
10K
100K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R558
R559
R560
R561
R562
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
– 101 –
Remark
MAIN (AUDIO, DIGITAL)
Ref. No.
MOTOR
Part No.
Description
Remark
R563
R564
R565
R566
R567
1-249-429-11
1-249-429-11
1-249-429-11
1-249-417-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
10K
10K
1K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R568
R569
R570
R571
R572
1-249-429-11
1-249-429-11
1-249-429-11
1-247-807-31
1-249-413-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
10K
10K
100
470
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R573
R574
R575
R576
R577
1-247-807-31
1-249-441-11
1-249-429-11
1-249-429-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
100
100K
10K
10K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R578
R581
R583
R584
R585
1-249-429-11
1-249-441-11
1-249-425-11
1-249-441-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
100K
4.7K
100K
100K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R586
R587
R588
R589
R590
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R591
R593
R594
R595
R596
1-249-441-11
1-249-417-11
1-249-421-11
1-249-417-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
1K
2.2K
1K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R597
R598
R600
R601
R602
1-249-441-11
1-249-441-11
1-249-425-11
1-249-425-11
1-249-425-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
100K
4.7K
4.7K
4.7K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R603
R604
R605
R606
R607
1-249-413-11
1-249-433-11
1-249-433-11
1-249-409-11
1-249-427-11
CARBON
CARBON
CARBON
CARBON
CARBON
470
22K
22K
220
6.8K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R608
R611
R612
R613
R614
1-249-417-11
1-249-411-11
1-249-437-11
1-249-429-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
330
47K
10K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R615
R616
R617
R618
1-247-807-31
1-249-429-11
1-249-435-11
1-249-421-11
CARBON
CARBON
CARBON
CARBON
100
10K
33K
2.2K
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
Ref. No.
Part No.
Description
Remark
R619
1-249-421-11 CARBON
2.2K
5%
1/4W
R620
R621
R622
R623
R625
1-247-807-31
1-247-804-11
1-249-429-11
1-249-429-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
100
75
10K
10K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R626
R627
R628
R629
R630
1-249-429-11
1-249-429-11
1-249-429-11
1-249-429-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R634
R635
R636
R637
R638
1-247-843-11
1-247-843-11
1-247-843-11
1-249-429-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
3.3K
3.3K
3.3K
10K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R639
R645
R647
R648
1-247-804-11
1-249-413-11
1-249-409-11
1-247-807-31
CARBON
CARBON
CARBON
CARBON
75
470
220
100
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
< VARIABLE RESISTOR >
RV501
RV502
1-241-763-11 RES, ADJ, CARBON 4.7K
1-241-763-11 RES, ADJ, CARBON 4.7K
< RELAY >
RY301
1-515-726-11 RELAY
< SWITCH >
S501
1-572-622-11 SWITCH, SLIDE (COAXIAL-AES/EBU)
< TRANSFORMER >
T501
1-409-594-11 COIL (WITH CORE)
< VIBRATOR >
X301
1-567-814-11 VIBRATOR, CRYSTAL (24.576MHz)
X302
1-567-815-31 VIBRATOR, CRYSTAL (22.5792MHz)
X501
1-567-814-11 VIBRATOR, CRYSTAL (24.576MHz)
X502
1-567-816-31 VIBRATOR, CRYSTAL (18.816MHz)
X503
1-567-098-61 VIBRATOR, CRYSTAL (32.768KHz)
***********************************************************
1-655-913-11 MOTOR BOARD
*************
*
< CAPACITOR >
C1
– 102 –
1-161-772-11 CERAMIC
0.1uF
10%
25V
PRIMARY
Ref. No.
Part No.
REC EN
Description
REC VOL
Remark
Ref. No.
REG
Part No.
< CONNECTOR >
1-664-488-11 PRIMARY BOARD
***************
*
3-346-266-12 PLATE, GROUND
1-113-916-11
1-113-916-11
1-113-920-11
1-113-920-11
1-113-920-11
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
Remark
1-664-490-11 REG BOARD
*********
*
< CAPACITOR >
0.01uF 20%
0.01uF 20%
0.0022uF 20%
0.0022uF 20%
0.0022uF 20%
C907
C908
C909
C910
C911
250V
250V
250V
250V
250V
1-164-159-11
1-164-159-11
1-136-177-00
1-136-177-00
1-162-294-31
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
0.1uF
0.1uF
1uF
5%
1uF
5%
0.001uF 10%
50V
50V
50V
50V
50V
< IC >
< CONNECTOR >
CN901
Description
RV103 1-225-400-11 RES, VAR 10K (REC LEVEL CH-1 (L))
RV203 1-225-400-11 RES, VAR 10K (REC LEVEL CH-2 (R))
************************************************************
< CAPACITOR >
! C901
! C902
! C903
! C904
! C905
REMOTE
< VARIABLE RESISTOR >
* CN1
1-564-498-11 PIN, CONNECTOR 5P
* CN2
1-564-337-00 PIN, CONNECTOR 3P
*************************************************************
*
REM SW
IC901
IC902
8-759-450-47 IC BA05T
8-759-390-48 IC uPC2406AHF
1-564-321-00 PIN, CONNECTOR 2P
< TRANSISTOR >
< INLET >
! IL901
Q901
8-729-209-15 TRANSISTOR 2SD2012
************************************************************
1-251-234-11 INLET, AC
< COIL >
! L901
1-664-483-11 REM SW BOARD
************
*
1-424-485-11 FILTER, LINE
< CONNECTOR >
< SWITCH >
* CN703
1-564-337-00 PIN, CONNECTOR 3P
! S901
1-554-920-51 SWITCH, PUSH (AC POWER) (1 KEY) (POWER)
**************************************************************
< RESISTOR >
1-654-393-11 REC EN BOARD
************
*
R728
R729
1-249-429-11 CARBON
1-249-435-11 CARBON
< SWITCH >
1-664-485-11 REC VOL BOARD
*************
A-2007-645-A REMOTE BOARD, COMPLETE
***********************
*
< CAPACITOR >
1-564-519-11 PLUG, CONNECTOR 4P
< RESISTOR >
R101
R201
1-249-421-11 CARBON
1-249-421-11 CARBON
1/4W
1/4W
S730
1-572-268-11 SWITCH, SLIDE (REMOTE)
***********************************************************
< CONNECTOR >
* CN306
5%
5%
< SWITCH >
S901
1-572-459-11 SWITCH, PUSH (REC PROOF/CASSETE IN)
***********************************************************
*
10K
33K
2.2K
2.2K
5%
5%
1/4W
1/4W
C811
C812
C813
C814
C815
1-162-306-11
1-162-306-11
1-162-306-11
1-162-306-11
1-162-306-11
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
20%
20%
20%
20%
20%
16V
16V
16V
16V
16V
C816
C817
1-162-306-11 CERAMIC
1-164-159-11 CERAMIC
0.01uF
0.1uF
20%
16V
50V
– 103 –
The components identified by
mark ! or dotted line with
mark ! are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque ! sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le neméro spécifié.
REMOTE
Ref. No.
C818
C819
Part No.
RF AMP
Description
Remark
1-162-294-31 CERAMIC
1-162-294-31 CERAMIC
0.001uF 10%
0.001uF 10%
50V
50V
< CONNECTOR >
CN801
1-691-768-11 PLUG (MICRO CONNECTOR) 6P
< CONPOSITION CIRCUIT BLOCK >
CP801
1-239-302-11 COMPOSITION CIRCUIT BLOCK
< IC >
IC802
8-759-916-20 IC SN74HC14AN
< JACK >
J803
J804
1-770-355-11 CONNECTOR (DIN) 8P (REMOTE)
1-507-743-00 JACK, STEREO MINIATURE (REMOTE 2)
< TRANSISTOR >
Q801
Q802
Q803
Q804
Q805
8-729-900-80
8-729-900-80
8-729-900-80
8-729-900-80
8-729-900-80
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114ES
DTC114ES
DTC114ES
DTC114ES
DTC114ES
Q806
Q807
Q808
8-729-900-80 TRANSISTOR DTC114ES
8-729-422-57 TRANSISTOR UN4111
8-729-422-57 TRANSISTOR UN4111
Ref. No.
Part No.
Description
Remark
C2
C3
C4
C5
1-163-019-00
1-163-251-11
1-107-682-11
1-164-299-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0068uF 10%
100PF 5%
1uF
10%
0.22uF 10%
50V
50V
16V
25V
C6
C7
C8
C9
C10
1-164-004-11
1-163-009-11
1-124-778-00
1-124-778-00
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
0.1uF
0.001uF
22uF
22uF
0.001uF
10%
10%
20%
20%
10%
25V
50V
6.3V
6.3V
50V
C11
C12
C13
C14
C15
1-164-004-11
1-164-299-11
1-107-682-11
1-163-251-11
1-124-778-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
0.1uF
0.22uF
1uF
100PF
22uF
10%
10%
10%
5%
20%
25V
25V
16V
50V
6.3V
C16
C17
C18
C19
C20
1-163-038-91
1-163-001-11
1-163-251-11
1-163-001-11
1-164-182-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
220PF 10%
100PF 5%
220PF 10%
0.0033uF 10%
25V
50V
50V
50V
50V
C21
C22
C23
C24
C25
1-163-005-11
1-126-603-11
1-163-251-11
1-163-038-91
1-124-778-00
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
470PF
4.7uF
100PF
0.1uF
22uF
50V
35V
50V
25V
6.3V
C26
C27
C28
1-163-038-91 CERAMIC CHIP
1-107-682-11 CERAMIC CHIP
1-164-505-11 CERAMIC CHIP
0.1uF
1uF
2.2uF
10%
20%
5%
20%
10%
25V
16V
16V
< RESISTOR >
< CONNECTOR >
R811
R812
R813
R814
R815
1-249-417-11
1-249-417-11
1-249-417-11
1-249-417-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R816
R817
R818
R819
R820
1-249-417-11
1-249-419-11
1-247-843-11
1-249-425-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
1.5K
3.3K
4.7K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R821
R822
R823
1-249-435-11 CARBON
1-249-409-11 CARBON
1-249-409-11 CARBON
33K
220
220
5%
5%
5%
1/4W
1/4W
1/4W
* CN51
* CN52
< IC >
IC1
A-2006-455-A RF AMP BOARD, COMPLETE
**********************
8-752-039-01 IC CXA1364R
< COIL >
L1
L2
L3
1-408-781-00 INDUCTOR CHIP 22uH
1-408-789-21 INDUCTOR CHIP 100uH
1-408-781-00 INDUCTOR CHIP 22uH
< RESISTOR >
**********************************************************
*
1-566-207-11 PIN, CONNECTOR (PC BOARD) 14P
1-564-720-11 PIN, CONNECTOR (SMALL TYPE) 4P
R1
R2
R3
R4
R5
1-216-082-00
1-216-082-00
1-216-066-00
1-216-066-00
1-216-077-00
METAL GLAZE
METAL GLAZE
METAL CHIP
METAL CHIP
METAL CHIP
R6
R7
1-216-077-00 METAL CHIP
1-216-077-00 METAL CHIP
24K
24K
5.1K
5.1K
15K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
15K
15K
5%
5%
1/10W
1/10W
< CAPACITOR >
C1
1-124-778-00 ELECT CHIP
22uF
20%
6.3V
– 104 –
RF AMP
Ref. No.
Part No.
S END
SHUTTLE
Description
Remark
R8
R9
R10
1-216-079-00 METAL CHIP
1-216-075-00 METAL CHIP
1-216-079-00 METAL CHIP
18K
12K
18K
5%
5%
5%
1/10W
1/10W
1/10W
R11
R12
R13
R14
R15
1-216-077-00
1-216-077-00
1-216-077-00
1-216-081-00
1-216-085-00
15K
15K
15K
22K
33K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R16
R17
R18
1-216-089-91 METAL GLAZE
1-216-080-00 METAL CHIP
1-216-073-00 METAL CHIP
47K
20K
10K
5%
5%
5%
1/10W
1/10W
1/10W
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SW
Ref. No.
T END
Part No.
THICK
UNBAL
Description
Remark
< TRANSISTOR >
Q951
1-808-957-11 TRANSISTOR PHOTO SENSOR (T END)
**************************************************************
1-654-394-12 THICK BOARD
***********
*
< SWITCH >
S904
1-572-458-11 SWITCH, PUSH (THICK)
************************************************************
< VARIABLE RESISTOR >
RV1
1-238-181-11 RES, ADJ, CERMET 4.7K
RV2
1-238-181-11 RES, ADJ, CERMET 4.7K
************************************************************
A-2007-646-A UNBAL BOARD, COMPLETE
**********************
*
< CAPACITOR >
1-654-392-11 S END BOARD
***********
*
< TRANSISTOR >
Q950
1-808-957-11 TRANSISTOR PHOTO SENSOR (S-END)
************************************************************
1-664-487-11 SHUTTLE BOARD
*************
*
C148
C149
C248
C249
C380
1-126-023-11
1-107-597-11
1-126-023-11
1-107-597-11
1-126-023-11
ELECT
CERAMIC
ELECT
CERAMIC
ELECT
100uF
22PF
100uF
22PF
100uF
C381
C382
1-164-159-11 CERAMIC
1-164-159-11 CERAMIC
0.1uF
0.1uF
20%
10%
20%
10%
20%
25V
500V
25V
500V
25V
50V
50V
< CONNECTOR >
< RESISTOR >
R757
R758
R759
R760
R761
1-249-413-11
1-249-413-11
1-249-413-11
1-249-413-11
1-249-413-11
CARBON
CARBON
CARBON
CARBON
CARBON
470
470
470
470
470
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R762
1-249-413-11 CARBON
470
5%
1/4W
CN314
CN315
CN316
CN317
CN318
1-691-766-21
1-691-766-31
1-691-766-11
1-691-766-41
1-691-765-21
PLUG (MICRO CONNECTOR) 4P
PLUG (MICRO CONNECTOR) 4P
PLUG (MICRO CONNECTOR) 4P
PLUG (MICRO CONNECTOR) 4P
PLUG (MICRO CONNECTOR) 3P
CN319
1-564-505-11 PLUG, CONNECTOR 2P
< DIODE >
< SWITCH >
D316
1-692-722-11 SWITCH, ROTARY (ENCODER)
(SHUTTLE
DATA)
************************************************************
8-719-987-63 DIODE 1N4148M
S736
< IC >
IC326
*
1-655-916-11 SW BOARD
********
< JACK >
< SWITCH >
J307
S1
1-571-958-11 SWITCH, PUSH (1 KEY)(CASSETTE TABLE OUT)
S2
1-571-958-11 SWITCH, PUSH (1 KEY)(CASSETTE TABLE IN)
************************************************************
*
8-759-981-96 IC RC4560D
1-770-163-21 JACK, PIN 4P (ANALOG UNBALANCE IN/OUT)
< TRANSISTOR >
Q316
1-654-391-11 T END BOARD
***********
– 105 –
8-729-900-80 TRANSISTOR DTC114ES
PCM-R500
UNBAL
Ref. No.
Part No.
Description
Remark
< RESISTOR >
R174
R175
R176
R177
R178
1-247-887-00
1-249-431-11
1-249-437-11
1-249-437-11
1-249-437-11
CARBON
CARBON
CARBON
CARBON
CARBON
220K
15K
47K
47K
47K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R179
R180
R274
R275
R276
1-247-807-31
1-249-415-11
1-247-887-00
1-249-431-11
1-249-437-11
CARBON
CARBON
CARBON
CARBON
CARBON
100
680
220K
15K
47K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R277
R278
R279
R280
1-249-437-11
1-249-437-11
1-247-807-31
1-249-415-11
CARBON
CARBON
CARBON
CARBON
47K
47K
100
680
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
Ref. No.
Part No.
Description
Remark
#12
#13
#14
#15
7-627-556-17
7-621-775-08
7-627-553-67
7-685-862-09
SCREW,PRECISION +P 2.6X3 TYPE1
SCREW +B 2.6X3
SCREW,PRECISION +P 2X5
SCREW+BVTT 2.6X6 (S)
#16
#17
#18
#19
#20
7-621-772-30
7-627-852-48
7-627-552-47
7-685-102-19
7-627-553-38
SCREW +B 2X6
PRECISION SCREW +P1.7X3.5TYPE3
SCREW,PRECISION +P 1.7X4
SCREW +P 2X4 TYPE2 NON-SLIT
SCREW,PRECISION +P 2X3
#21
7-685-133-19 SCREW +BTP 2.6X6 TYPE2 N-S
#22
7-628-253-00 SCREW +PS 2X4
#23
7-685-871-01 SCREW +BVTT 3X6 (S)
#24
7-685-645-79 SCREW +BVTP 3X6 TYPE2 IT-3
#25
7-627-553-27 SCREW, PRECISION +P2X2.5
************************************************************
ACCESSORIES & PACKING MATERIALS
*******************************
< RELAY >
RY305 1-515-726-11 RELAY
************************************************************
!
!
MISCELLANEOUS
*************
58
113
M901
M902
M903
1-769-541-11
1-769-542-11
A-2003-660-A
8-835-306-01
8-835-205-01
WIRE (FLAT TYPE) (17 CORE)
WIRE (FLAT TYPE) (31 CORE)
MOTER ASSY (LODING)
MOTOR,DC U-17A (CAPSTAN)
MOTOR,DC U-2A (REEL) (including PM901)
1-473-921-11
1-551-812-11
1-590-910-11
2-297-913-00
3-859-278-11
REMOTE COMMANDER (RM-D757)
CORD, POWER(US,Canadian)
CORD SET, POWER(AEP)
WASHER (DIA.5), ORNAMENTAL
MANUAL, INSTRUCTION
(ENGLISH,FRENCH,GERMAN)
4-981-643-01 COVER, BATTERY(for RM-D757)
7-682-276-04 SCREW +RK 5X12
M904
8-848-626-11 DRUM ASSY DOU-03D
M905
X-3370-655-1 MOTER ASSY (CASSETTE COMPARTMENT)
PM902 1-454-522-11 SOLENOID, PLUNGER
! T901
1-431-064-11 TRANSFORMER, POWER (US, Canadian)
! T901
1-431-065-11 TRANSFORMER, POWER (AEP)
************************************************************
**************
HARDWARE LIST
**************
#1
#2
#3
#4
#5
7-685-872-09
7-685-872-09
7-685-646-79
7-685-881-01
7-682-660-09
SCREW +BVTT 3X8 (S)
SCREW +BVTT 3X8 (S)
SCREW +BVTP 3X8 TYPE2 N-S
SCREW +BVTT 4X8 (S)
SCREW +PS 4X6
#6
#7
#8
#9
#10
7-685-660-29
7-621-772-18
7-682-550-09
7-621-772-20
7-621-773-86
SCREW +BVTP 4X10 TYPE2 SLIT
SCREW +B 2X4
SCREW +B 3X12
SCREW +B 2X5
SCREW +B 2.6X4
#11
7-621-772-08 SCREW +B 2X3
The components identified by
mark ! or dotted line with
mark ! are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque ! sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le neméro spécifié.
Sony Corporation
9-960-833-11
Home A&V Products Company
– 106 –
96L0510-1
Printed in Japan © 1996. 12
Published by Service and Safety
Engineering Dept. (Shibaura)