Download EMP 4 ECO+ - Fysiopartner AS
Transcript
DE / EN EMP 4 ECO+ Muskelstimulator für Physiotherapeuten Gerät für die transkutane Nerven- und Muskelstimulation Muscle Stimulator for Physiotherapists Art.-Nr. 101060 Gebrauchsanweisung/Instruction manual Art.-Nr. 101707 2 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Inhalt Allgemeine Informationen................................3 Beschreibung des Gerätes.................................4 Beschreibung der Symbole................................4 Technische Daten................................................5 Bedienung des EMP 4 ECO+.............................6 Stimulation und Einstellung der Intensität......9 Dynamische Stimulation.................................. 11 Kurzgebrauchsanweisung...............................12 Beschreibung der Programme........................13 Technische Informationen...............................23 Zubehör.............................................................25 Lieferumfang.....................................................27 Elektrodenanlage.............................................28 Medizinptroduktebuch.....................................34 Programmübersicht..........................................71 3 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Allgemeine Informationen Anwendungsgebiete Das EMP 4 ECO + ist für die Stimulation der Muskeln und Nerven konzipiert worden. Verwenden Sie dieses Gerät für keine anderen Zwecke. Wichtige Sicherheitshinweise Lesen Sie die Bedienungsanleitung vor der Benutzung des Gerätes aufmerksam durch! Für die risikolose erste Benutzung des Gerätes: Der EMP 4 ECO + darf nur mit dem Originalzubehör verwendet werden (Kabel Typ 5.15, STIMEX Selbstklebeelektroden). Halten Sie Wasser oder andere Flüssigkeiten vom EMP 4 ECO + fern. Lassen Sie das Gerät nicht fallen, lagern Sie das Gerät bei einer angemessenen Temperatur zwischen 10 Grad Celsius und 40 Grad Celsius und einer Luftfeuchtigkeit unter 90%. Benutzen Sie das EMP 4 ECO + nie, wenn es fehlerhaft arbeitet oder beschädigt worden ist. Bewahren Sie das Gerät nach dem Gebrauch zur Vermeidung eventueller Beschädigung in der Originalverpackung auf. Sicherheitsmaßnahmen und Gegenanzeigen Personen mit einem elektronischen Herzschrittmacher, Personen mit Hautprobleme im Bereich der Elektroden sowie Schwangere dürfen den EMP 4 ECO + nicht ohne Rücksprache mit einem Arzt verwenden. Das EMP 4 ECO + darf jeweils nur an eine Person angeschlossen werden. Warnhinweis! Das EMP 4 ECO + sollte nicht in der Nähe von Mikrowellen, Kurzwellen oder Ultrakurzwellen (Mobiltelefon, WLAN Systeme, Bluetooth Systeme) verwendet werden. Diese Geräte können die Parameter des EMP 4 ECO + stören. 4 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Beschreibung des Gerätes Das EMP 4 ECO + ist für die Stimulation der Muskeln und Nerven konzipiert worden. Die Bedienung erfolgt durch Drücken der Tasten. Die verwendeten Einstellungen werden auf dem Display angezeigt. 1 2 3 4 5 1. Anzeigedisplay 2. Programmtaste 3. Taste zur Auswahl der Parameter im Edit Modus und Pause-Taste im Stimulationsmodus 4. Tasten zur Änderung der Parameter im Edit Modus und Intensitätstasten im Stimulationsmodus 5. Ein/Aus Taste 6. Ausgangsbuchsen für die Kabel 7. Ausgangsbuche für das Ladegerät 8. Ein/Aus-Schalter 6 7 6 8 Beschreibung der Symbole Achtung, Begleitdokumente, insbesondere Gebrauchsanweisung beachten! 0434 Mit der Anbringung der CE-Kennzeichnung erklärt der Hersteller, dass das Produkt alle zutreffenden Anforderungen der zu berücksichtigenden EG-Richtlinien erfüllt und ein für das Produkt vorgeschriebenes Konformitätsbewertungsverfahren erfolgreich abgeschlossen wurde. Die Kennnummer der bei der Durchführung des Konformitätsbewertungsverfahrens beteiligten Benannten Stelle ist nach der CEKennzeichnung angegeben. 5 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Anwendungsteil des Typs BF Seriennummer Bestellnummer Herstellungsdatum Hersteller Umweltschutz: Geben Sie das Gerät am Ende der Lebensdauer nicht in den normalen Hausmüll. Bringen Sie es zum Recycling zu einer offiziellen Sammelstelle. Auf diese Weise helfen Sie die Umwelt zu schonen. Technische Daten Muskel- und Nervenstimulator mit 2x2 galvanisch getrennte Kanäle (4x100 mA max.), vom Typ Konstantstrom biphasisch, symmetrisch mit 25 feste Programmen und 20 editierbaren Programmen. Stromaufnahme max. 100 mA (bei reeller Last von 1 kΩ) Frequenzbereich 1-120 Hz Impulsbreitenbereich 50-500 μs Ausgangsstrom 15 mA U I U Spannungsversorgung Integrierter Akkumulator NI-MHI 4,8V Abmessung 120x75x35 mm Gewicht ca. 250 g t t t Impulsform Symmetrisch, biphasisch mit Pause An Last 1 kΩ reel An Last ANSI/AAMI Standard U U t t U U t 6 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Bedienung des EMP 4 ECO+ Anschluss von Kabeln und Elektroden Schließen Sie die Kabel mit den Elektroden (2 pro Kabel) an. Stecken Sie das andere Ende des Kabels in eine der Ausgangsbuchsen am oberen Ende des Gerätes. Platzieren Sie die Elektroden auf die Haut. Gerät einschalten Das Gerät lässt sich mit der Taste einschalten. Im Display wird das zuletzt verwendete Programm angezeigt. Sollte das Gerät im Tastensperren-Modus sein, erscheint ein kleiner Schlüssel oben links im Display (Siehe Kapitel Tastensperre). Programmwahl Drücken Sie die P Taste um das gewünschte Programm auszuwählen. Hierfür ist es notwendig, dass die Tastensperre nicht aktiviert ist. Drücken Sie die P Taste solange bis das gewünschte Programm im Display erscheint. Mit den Tasten beider Kanäle können Sie zurück blättern. Stimulation starten Vergewissern Sie sich, dass Sie das richtige Programm gewählt haben und dass die Elektroden und Kabel richtig angeschlossen sind. Starten Sie die Stimulation mit der/den Taste(n) des Kanals an dem Sie die Kabel angeschlossen haben. Regeln der Intensität Drücken Sie die Taste(n) des/der angeschlossene(n) Kanals/Kanäle zum Erhöhen der Stromintensität solange bis die Stimulation für Sie angenehm ist. Die Intensität kann mit der Taste verringert werden. Die gewählte Intensität wird auf dem Display angezeigt und kann zwischen 1 und 100 mA geregelt werden. 7 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Achtung! Sicherungssperre der Intensität Um eine willkürliche Erhöhung der Intensität zu vermeiden, wird die Intensität auf dem zuletzt geregelten Niveau nach 5 s blockiert. Um die Intensität erneut hoch zu regeln, muss diese erst mit der Taste runter geregelt werden und dann wieder mit der Taste hoch geregelt werden. Sind die Elektroden und/oder die Kabel nicht richtig angebracht/gesteckt, lässt sich die Intensität des EMP 4 PRO + nicht höher als 10 mA regeln und schaltet automatisch zurück auf null. Wichtig! Um die Intensität schneller hoch oder runter zu regeln, halten Sie die oder Tasten gedrückt. Stimulation stoppen Drücken der P oder Taste für eine Sekunde um die Stimulation zu stoppen. Die Stimulation stoppt automatisch, wenn die Programmdauer abgelaufen ist. Stimulation pausieren Drücken Sie die E Taste während der Stimulation, um diese zu pausieren. Sie können in dieser Pause beispielsweise die Elektrodenanlage verändern. Das Wort „PAUSE“ erscheint auf dem Display. Drücken Sie erneut die E Taste um die Stimulation zu starten. Das EMP 4 PRO + fährt die Intensität langsam bis zu den bisher gewählten Niveau hoch. Programmierung der USER Programme U1 bis U20 Drücken Sie die E Taste um im Programmierungsmodus des gewählten Programmes zu gelangen. Die veränderbaren Parameter blinken im Display. Verändern Sie die Parameter wie gewünscht mit den Tasten beider Kanäle. Durch Drücken der E Tasten gelangen Sie zum nächsten Parameter. 8 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Folgende Parameter können verändert werden: Programm 1, 3, 4, 9, 20 Frequenz 20-120 Hz Impulsbreite 70-500 µs Zeit 1-99 min Programm 2, 5 (TENS) 80, 90, 100, 110, 120 Hz Frequenz Kanal und 2, 5, 10 Hz Frequenz Kanal und Impulsbreite 70-500 µs Zeit 1-99 min Programm 6 Zeit 1-99 min Programm 7, 8 Maximale Frequenz 10-120 Hz Minimale Frequenz 2 Hz Impulsbreite 70-180 µs Zeit 1-99 min Programm 10, 11, 17 Frequenz 1-120 Hz Impulsbreite 70-500 µs Zeit 1-99 min Programm 12, 13, 14, 15, 16, 18, 19 Frequenz 20-120 Hz Impulsbreite 70-500 µs Anstiegszeit 1-4 s Arbeitszeit 1-25 s Pause 1-25 s Zeit 1-99 min Gerät ausschalten Drücken Sie die Tasten für eine Sekunde um die Stimulation zu stoppen. Drücken Sie die Taste ein zweites Mal um das EMP 4 ECO + auszuschalten. Ist die Akkuleistung nicht stark genug, so schaltet das Gerät automatisch ab. Wird das Gerät für 2 Minuten nicht benutzt, schaltet es ebenfalls automatisch ab. 9 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Laden des Akkumulators Die Spannung des Akkus wird im Display mittels 4 Balken in der Batterieanzeige dargestellt. Unterschreitet die Spannung ein kritisches Niveau, schaltet das Gerät ab und kann nicht mehr angeschaltet werden bevor der eingebaute Akku geladen wird. Laden Sie das EMP 4 ECO + ausschließlich mit dem gelieferten Ladegerät. Ladebuchse Ladegerät Schalten Sie den Schiebeschalter auf die Position „OFF“ (siehe Bild). Stecken Sie das Ladegerät in der Buchse mittig auf der Unterseite des EMP4 ECO + zwischen den Kabelbuchsen. Verbinden Sie das Ladegerät mit einer 220V Steckdose. Die Diode auf dem Ladegerät leuchtet in rot. Laden Sie das EMP 4 ECO + bis die Diode auf dem Ladegerät von rot auf grün schaltet. Die grüne Diode zeigt an, dass der Ladevorgang abgeschlossen ist. Wichtig! Trennen Sie das Ladegerät von der 220 V Steckdose und trennen Sie das Ladegerät vom EMP4 ECO +. Achtung! Vergessen Sie nicht den Schiebeschalter auf der Unterseite des EMP 4 ECO + wieder auf die Position „ON“ zu setzen, um das Gerät wieder betriebsbereit zu stellen. Stimulation und Einstellung der Intensität Versuchen Sie nicht eine immer höhere Intensität (in mA) zu regeln. Wählen Sie eine Intensität bei der Sie sich wohl fühlen und dies unabhängig davon, welche Programmgruppe Sie verwenden (Erholung, Schmerztherapie, Muskeltraining). Regeln Sie die Intensität bis zu einer leichten Schmerzgrenze und reduzieren Sie dann die Intensität Schritt für Schritt bis zu einem komfortablen Niveau. Sie werden bemerken, dass sich das komfortable Niveau in der Zeit verändern kann, auch wenn Sie an der gleiche Stelle wie bisher stimulieren. Dies ist ein normaler Effekt, da verschiedene Faktoren die Stromtoleranz und dessen Niveau beeinflussen: 10 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Hautwiderstand: Trockene Haut leitet weniger Strom als feuchte Haut (Einfluss des Schweißes). Desweiteren ist der Hautwiderstand nicht gleichmäßig je nach Körperregion. Beispielsweise ist der Hautwiderstand auf einer Hornhaut zwei Mal so groß wie in der Kniekehle. Auch die Innervation ist unterschiedlich je nach Stimulationsareal, was gleichfalls Unterschiede in der Sensibilität erklärt. Volumen der Muskelmasse: Je größer die Muskelmasse ist, desto höher sollte die Intensität bei gleichen Parametern geregelt werden. Ermüdungszustand des Muskels: Je stärker der Muskel ermüdet ist, desto weniger Intensität wird dieser ertragen. Zustand der verwendeten Elektroden: Selbstklebende Elektroden haben eine begrenzte Lebensdauer (30 bis 50 Anwendungen je nach Qualität). Mit dem Alter erhöht sich der Widerstand der Elektroden und deren Leitfähigkeit verringert sich. Denken Sie daran Elektroden regelmäßig auszutauschen. Gewöhnung des Nervensystems an den Strom: Während der ersten 5 Minuten der Stimulation stellt der Anwender häufig fest, dass die Sensibilität zum Strom sich verändert. Obwohl die Strommenge konstant bleibt, haben viele Anwender das Gefühl den Strom weniger zu spüren. Das Nervensystem hat sich an den Strom einfach gewöhnt. Dies tritt weniger auf bei Verwendung von Dynamic Programmen. Zögern Sie nicht, die Intensität nachträglich zu erhöhen und trotzallem ein angenehmes Niveau beizubehalten. Vielfältigkeit der Parameter: Die in den Programmen verwendeten Frequenzen und Impulsbreiten sind vielfältig. Auch dies erklärt, weshalb unterschiedliche Intensitäten auf ein und demselben Stimulationsareal gewählt werden. Es gelten beispielsweise folgenden Faustregeln: Je höher die Frequenz, desto geringer die Intensität. Je größer die Impulsbreite, desto geringer die Intensität. 11 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Dynamische Stimulation Das Prinzip der dynamischen Stimulation besteht darin, dass die Stimulation nicht auf alle Kanäle gleichzeitig appliziert wird. Die dynamische Stimulation erzeugt eine Wellenbewegung des Stimulationsimpulses, der sich zwischen den Elektrodenpaaren hin und her bewegt und damit eine bessere Nachbildung von Massageeffekten erzielt. Die dynamische Stimulation wird vom Anwender als angenehmer empfunden als klassische neuro-muskuläre Stimulation. Die Verteilung des Stroms auf die 4 Kanäle nacheinander ermöglicht gute Ergebnisse sowohl bei schmerzlindernder Behandlung als auch bei niederfrequenter Muskellockerung. Die Anwendung der dynamischen Stimulation bei Lymphdrainagen betont die Wirkung der wellenartigen Muskelkontraktion. Elektrodenanlage für dynamische Stimulationsprogramme Kanal 1 Kanal 2 Verlaufsschema der dynamischen Stimulation Kanal 1 Kanal 2 Kanal 3 Kanal 4 Kanal 1 Kanal 2 Kanal 3 Seitwärts Bewegung (Gesäß, Bauch) Kanal 1 Kanal 4 Absteigend (Rücken, Beine) Kanal 4 Kanal 2 Kanal 3 empfehlen wir die Für die Stimulation der unteren Extremitäten Verwendung von 5x9 cm Elektroden. Befestigen Sie eine ElektroKanal 3 Kanal 2 de jedes Kanals je auf einem Bein. Kanal 4 Kanal 1 Sie eine Elektrode Für die paravertebrale Stimulation befestigen jedes Kanals je rechts und links der Wirbelsäule. Achtung! Sollten Sie Elektroden mit Doppelanschlüsse verwenden, so stecken Sie immer die Stecker gleicher Farben in eine Elektrode (2 blaue oder 2 rote). Kanal 3 Kanal 4 12 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Kurzgebrauchsanweisung Kurzgebrauchsanweisung Wichtig! Verbinden Sie die Kabel mit dem Gerät und mit den Elektroden (2 Elektroden pro Kabel) bevor Sie das Gerät einschalten. Gerät Ein-/Ausstellen Programmwahl Drücken Sie die P Tasten um das gewünschte Programm auszuwählen. Intensitätsregelung Intensitäten Kanal Kanal Intensitäten Kanal Kanal Zum Erhöhen Zum Erhöhen Zum Verringern Achtung: Die Intensitäten werden automatisch verriegelt. Um die Zum Verringern Intensität zu erhöhen, muss diese erst einmal verringert werden und sofort wieder erhöht werden. Stimulation stoppen Um die Stimulation zu stoppen halten Sie die P Taste 2 Sekunden gedrückt. 13 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Beschreibung der Programme Frequenz Hz Intensität 100 } T = 1/f Anstiegsphase Impulsbreite Programm 1 + U1: Abstiegsphase Lumbales Schmerzsyndrom Gate Control 50 Zeit Zeit Stimulationsart Parameter s (langsam) Gate Control 80 Hz dynamische Stimulation 7,5 15 Frequenz: 80 Hz Impulsbreite: 150 μs Intensität mA 20 min Dauer: 70 Aufstiegsrampe: 1 s Arbeitsphase PausenAbstiegsrampe: 1 s phase Symbole im Display Aufstiegsphase Zeit Abstiegsphase Zeit s 8 2 7 Beschreibung Die 4 Kanäle arbeiten laufend mit der gleichen Frequenz und Impulsbreite. Kanal 2 Ans Kanal 1 gspha tieg sph Abstie ase Intensität se Frequenz Hz 100 Intensität Phase 1 50 Frequenz Hz Programm 2 + U2: 100 30 Zeit min Lumboischialgie Phase 1 Zeit Intensität I mA T = 1/f Phase 2 2 3 s 6 Intensität Arbeitsphase Kanal 2 Ans Arbeitsphase gspha Arbeitsphase 0,5 50 Intensität mA Pausenphase 70 se Pausenphase 0,25 100 70 Abstie Symbole im Display Beschreibung Impulse Gate Control 80 Hz + 2 Hz Endorphinausschüttung Impulsbreite Zeit t Frequenz: Kanal und : 80 Hz s Frequenz: Kanal und : 2 Hz Zeit Impulsbreite: 200 μs Dauer: 20 min Intensität } Stimulationsart Parameter Zeit Frequenz Hz T = 1/f ase 50 75 µs 200 µs Intensität } 20 } 10 tieg sph Phase 2 2 0,75 1 Kanal 1 Zeit s 2 7 Zeit 8 Zeit Frequenz Hz 100 Intensität Phase 1 50 Phase 2 2 10 20 30 Zeit min 14 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Frequenz Hz Intensität 100 } T = 1/f Anstiegsphase Impulsbreite Programm 3 + U3: Cervicobrachialgie Abstiegsphase 50 Intensität Zeit Gate Control 80 Hz dynamische Stimulation (schnell) 7,5 15 Impulsbreite Frequenz: 80 Hz Impulsbreite: 150 μs Intensität mA 20 min Dauer: Zeit 70 Aufstiegsrampe: 0,2 Arbeitsphase s PausenAbstiegsrampe: 0,2 s phase Symbole im Display Aufstiegsphase Kanal 2 Intensität Zeit Abstiegsphase Zeit s 8 2 7 Beschreibung Die 4 Kanäle arbeiten laufend mit der gleichen Kanal 1 Frequenz und Impulsbreite. Kanal 2 ase sph tieg Ans gspha 50 Intensität mA 70 A se Frequenz Hz 100 100 Abstie Kanal 1 Frequenz Hz } Stimulationsart Parameter Intensität Zeit s T = 1/f Intensität Zeit Phase 1 50 Phase 2 2 10 20 30 Zeit min Frequenz Hz 100 Intensität Zeit Phase 1 50 Phase 1 Programm 4 + U4: Chronische Schmerzen 2 T = 1/f 200 µs } 100 Intensität I mA 75 µs 10 Phase 2 20 } Frequenz Hz 30 Zeit min 50 Stimulationsart Zeit Parameter s Phase 2 2 3 6 0,25 0,5 0,75 tieg sph 1 Zeit s 2 8 7 Arbeitsphase Pausenphase Intensität se Pausenphase Ans Arbeitsphase Zeit Arbeitsphase Pausenphase 0,25 0,5 0,75 1 Intensität I mA Zeit s gspha Arbeitsphase Zeit t s Abstie ase Impulse Frequenz Burst 2 Hz Endorphinausschüttung Hz 100 Phase 1Hz Frequenz: 100 Impulsbreite: 150 μs 50 Dauer: 20 min Intensität Arbeitsphase: 0,25Phase s2 70 2 Pause: 0,25 s 3 Arbeitsphase 6 Symbole im Display Arbeitsphase Pause Beschreibung Impulse Zeit s 70 15 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Programm 5 + U5: Gate Control + Endorphinausschüttung Stimulationsart Parameter Gate Control auf Kanal 1 + Endorphinausschüttung auf Kanal 2 Frequenz: Kanal und : 100 Hz Frequenz: Kanal und : 2 Hz Intensität Impulsbreite: 200 μs T = 1/f Dauer: 20 min Frequenz Hz 100 Impulsbreite } Symbole im Display Beschreibung Die Kanäle und arbeiten mit der gleichen Frequenz von 100 Hz (zwischen 80 und 120 Hz im Zeit USER Mode). Die Kanäle und arbeiten mit der gleichen Frequenz von 2 Hz (zwischen 0,5 und 10 Hz im USER Mode). Intensität Intensität } T = 1/f Kanal 2 50 Frequenz Intensität Hz mA 100 70 Impulsbreite 50 Kanal 1 Zeit Zeit Gonarthrose - Coxarthrose Intensität Intensität mA Kanal 2 70 Phase 1 Kanal 1 50 Stimulationsart Parameter HAN Phase 1 2 Frequenz: 100 HzPhase 2 Zeit Zeit min 10 20 30 Impulsbreite: 100 μs Dauer: 3 s Frequenz Frequenz Hz 2 Frequenz: 2 Hz Phase Hz 100 100 Phase 1 Phase 1 Impulsbreite: 200 μs Dauer: 3s 50 50 Diese 2 Phase folgen alle 3 s aufeinander. Phase 2 Dauer: 20 min Phase 2 22 Zeit Zeit s min 6 103 20 30 Symbole im Display Phase 1 Phase 2 Frequenz Beschreibung Hz 100 Impulse 50 Phase 1 A Programm 6 + U6: Frequenz Intensität Hz 100 Intensität I Intensität mA Intensität I mA Intensität 70 Arbeitsphase Arbeitsphase PausenPhase 2 phase 2 3 0,25 6 0,5 0,75 1 Zeit s Zeit s Intensität Impulse 70 16 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Programm 7 + U7: Epicondylitis Stimulationsart Parameter Modulation Minimalfrequenz: 2Hz (Impulsbreite: 200 µs) Maximalfrequenz: 80Hz (Impulsbreite: 100 µs) Modulationsfrequenz: 7,5 s Dauer: 20 min Aufstiegsrampe: 0,2 s Abstiegsrampe: 0,2 s Symbole im Display Aufstiegsphase Abstiegsphase Frequenz Beschreibung Hz Intensität 100 } T = 1/f Anstiegsphase Impulsbreite Abstiegsphase 50 Zeit 7,5 Intensität mA 70 Abstie Arbeitsphase Phase 1 50 Phase 2 2 10 } 20 T = 1/f Frequenz Hz 100 Ans 100 Anstiegsphase Impulsbreite Intensität I mA 50 Phase 1 T = 1/f 75 µs 200 µs } Zeit Abstiegsphase } Intensität 50 7,5 Phase 2 2 3 Intensität 6 2 Kanal Pausenphase Modulation Minimalfrequenz: 2Hz (Impulsbreite: 148 µs)Zeit Zeit 8 Maximalfrequenz: 80Hz (Impulsbreite: 70 µs)s 2 7 Modulationsfrequenz: 7,5 s Dauer: Intensität 20 min Aufstiegsrampe: 0,2 s Abstiegsrampe: 0,2 s Symbole im Display Aufstiegsphase Abstiegsphase Zeit Zeit Frequenz Beschreibung min Hz 30 se Frequenz Hz 100 Stimulationsart Parameter gspha Kanal 1 tieg sph Algodystrophie ase Kanal 2 Intensität Programm 8 + U8: Zeit s 15 Zeit s Zeit s 15 Zeit t s Intensität mA 70 Ans t Arbeitsphase Arbeitsphase Pausenphase Ans Arbeitsphase Zeit tieg sph ase 70 2 7 se se gspha gspha Abstie Kanal 1 Impulse ieg sph ase Arbeitsphase Abstie Intensität 8 Pausenphase Pausenphase Zeit s 17 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Frequenz Hz Intensität 100 } T = 1/f Anstiegsphase Impulsbreite Programm 9 + U9: Abstiegsphase Gate Control Dynamic (Entgewöhnung) 50 Zeit Zeit Stimulationsart Parameter s (schnell) Gate Control 80 Hz dynamische Stimulation 7,5 15 Frequenz: 80 Hz Impulsbreite: 150 μs Intensität mA 20 min Dauer: 70 Aufstiegsrampe: 0,5 Arbeitsphase s PausenAbstiegsrampe: 0,5 s phase Symbole im Display Aufstiegsphase Zeit Abstiegsphase Zeit s 8 2 7 Beschreibung Die 4 Kanäle arbeiten laufend mit der gleichen Frequenz und Impulsbreite. Kanal 2 Ans Kanal 1 gspha tieg sph Abstie ase Intensität se Frequenz Hz 100 Intensität Phase 1 50 10 20 30 Zeit min Frequenz Hz Intensität I mA Phase 1 Programm 10 + U10: µs Klassische Gate Control 120200Hz } 100 Zeit T = 1/f 75 µs } Phase 2 2 50 0,5 0,75 1 T = 1/f Zeit s Pausenphase Frequenz Hz 2 Impulsbreite 7 8 Zeit 100 50 Zeit Intensität Intensität mA Kanal 2 70 Kanal 1 An 0,25 Intensität se Pausenphase Symbole im Display Beschreibung gspha Arbeitsphase Abstie Arbeitsphase Zeit t s ase Impulse TENS klassisch Frequenz: 120 Hz Impulsbreite: 150 μs Dauer: 20 min Intensität Arbeitsphase: 0,25 s 70 Pause: 0,25 s Arbeitsphase tieg sph 6 } 3 Ans Stimulationsart Zeit Parameter s Phase 2 2 Zeit 18 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Programm 11 + U11: Krampfbehandlung Stimulationsart Parameter TENS klassisch Frequenz: 1 Hz Impulsbreite: 150 μs Dauer: 20 min Arbeitsphase: 0,25 s Pause: 0,25 s Symbole im Display Beschreibung siehe Programm 10 Muskelstimulationsprogramme Symbole Programm 12 + U12: Intensität } Atrophie obere Extremitäten Stimulationsart Parameter T = 1/f Impulsbreite Zeit Beschreibung Kanal 2 Intensität Aufstiegsphase Arbeitsphase Pause Frequenz Hz Muskelstimulation 100 Frequenz: 35AnstiegsHz phase Impulsbreite: 150 μs 50 Aufstiegsrampe: 0,25 s Arbeitszeit: 3 s 7,5 Pause: 9 s Dauer: 20 min 70 10 20 30 Zeit min Frequenz Hz 50 Phase 1 Zeit s 8 Intensität Phase 2 2 Pausenphase Atrophie untere Extremitäten Stimulationsart Parameter 50 7 Beschreibung Muskelstimulation Frequenz: 35 Hz Impulsbreite: 300 μs Aufstiegsrampe: 2 s Arbeitszeit: 3 s Pause: 9 s Intensität I mA Dauer: 20 min T = 1/f µs 75 siehe Programm 12 200 µs } Phase 1 2 } Programm 13 + U13: sphase Ans tieg sph ase Arbeitsphase g Abstie Zeit 100 Zeit s 15 Intensität mA Kanal 1 Frequenz Hz 100 Abstiegsphase Zeit 19 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Programm 14 + U14: Kräftigung obere Extremitäten Stimulationsart Parameter Beschreibung Programm 15 + U15: Kräftigung untere Extremitäten Stimulationsart Parameter Beschreibung Programm 16 + U16: Muskelstimulation Frequenz: 65 Hz Impulsbreite: 250 μs Aufstiegsrampe: 2 s Arbeitszeit: 4 s Pause: 8 s Dauer: 20 min siehe Programm 12 Muskelstimulation Frequenz: 65 Hz Impulsbreite: 300 μs Aufstiegsrampe: 2 s Arbeitszeit: 4 s Pause: 8 s Dauer: 20 min siehe Programm 12 Venöser Rückfluss Stimulationsart Parameter Beschreibung Muskelstimulation Frequenz: 35 Hz Impulsbreite: 250 μs Aufstiegsrampe: 2 s Arbeitszeit: 5 s Pause: 10 s Dauer: 20 min siehe Programm 12 Programm 17 + U17: URO - Dranginkontinenz Stimulationsart Parameter Beschreibung TENS klassisch Frequenz: 10 Hz Impulsbreite: 180 μs Dauer: 15 min siehe Programm 10 20 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Programm 18 + U18: URO - Mischinkontinenz Stimulationsart Parameter Beschreibung Muskelstimulation Frequenz: 20 Hz Impulsbreite: 180 μs Aufstiegsrampe: 2 s Arbeitszeit: 4 s Pause: 4 s Dauer: 15 min siehe Programm 12 Programm 19 + U19: URO - Stressinkontinenz Stimulationsart Parameter Beschreibung Frequenz Hz Intensität 100 T = 1/f } Muskelstimulation Frequenz: 50 Hz Impulsbreite: 180 μs Aufstiegsrampe: 2 s Arbeitszeit: 3 s Pause: 6 s Dauer: 15 min siehe Programm 12 Anstiegsphase Impulsbreite Programm 20 + U20: Abstiegsphase Entspannung (dynamische Stimulation) 50 Zeit Zeit Stimulationsart Parameter Kanal 2 tieg sph ase Intensität Ans Kanal 1 Frequenz Hz 100 se gspha Abstie s Dynamische Stimulation 7,5 (langsam) 15 Frequenz: 120 Hz Impulsbreite: 150 μs Intensität mA 20 min Dauer: 70 Aufstiegsrampe: 2 s Arbeitsphase PausenAbstiegsrampe: 2 s phase Symbole im Display Aufstiegsphase Zeit Abstiegsphase Zeit s 8 2 7 Beschreibung Die 4 Kanäle arbeiten laufend mit der gleichen Frequenz und Impulsbreite. Intensität Phase 1 50 Phase 2 2 10 Frequenz Hz 20 30 Zeit min Zeit Intensität I mA tieg sp sp bstieg Pausenphase 21 hase Ans Kanal 1 Zeit s Zeit 2 schwa-medico Gebrauchsanweisung - EMP7 4 8ECO+ Intensität Phase 1 Programm 21 + U21: Kombination aus aktiver Mobilisation des Handgelenks und Schmerzbehandlung 50 Phase 2 2 10 20 30 Frequenz Hz Phase 1 Zeit Muskelstimulation und Gate Control Frequenz: Kanal und : 45 Hz Intensität I mA Frequenz: Kanal T = 1/fund : 90 Hz 75 µs 200 µs 200 Impulsbreite: μs Aufstiegsrampe: 3 s Arbeitszeit: 1 s Abstiegszeit: 1 s Pause: 6 s Dauer: 20 min } 100 Zeit min Stimulationsart Parameter 50 Phase 2 2 3 Zeit s 6 Beschreibung Impulse } Frequenz Hz 100 Intensität Ans Arbeitsphase gspha tieg sph Abstie Arbeitsphase ase Kanal 70 und Arbeitsphase 0,5 Pausenphase se Pausenphase 0,25 Zeit t s 0,75 1 Zeit s 2 7 Zeit 8 Frequenz Hz Intensität Kanal und 100 } T = 1/f Impulsbreite 50 Zeit Kombination aus aktiver Mobilisation des Ellbogens Intensität und Schmerzbehandlung Intensität mA Kanal 2 Stimulationsart Parameter Beschreibung 70 Kanal 1 Muskelstimulation und Gate Control Frequenz: Kanal und : 45 Hz Frequenz: Kanal und : 90 Hz Impulsbreite: 250 μs Frequenz Aufstiegsrampe: 5s Hz 100 Arbeitszeit: 1 s1 Phase Abstiegszeit: 5 s 50 Pause: 10 s Dauer: 20 min Phase 2 2 Siehe Programm10 21 20 Frequenz Hz 100 An Programm 22 + U22: Zeit Intensität 30 Zeit min Intensität I mA Phase 1 2 50 Phase 2 22 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Programm 23 + U2: Kombination aus aktiver Mobilisation des Kniegelenkes und Schmerzbehandlung Stimulationsart Parameter Beschreibung Programm 24 + U24: Muskelstimulation und Gate Control Frequenz: Kanal und : 45 Hz Frequenz: Kanal und : 90 Hz Impulsbreite: 300 μs Aufstiegsrampe: 5 s Arbeitszeit: 1 s Abstiegszeit: 5 s Pause: 10 s Dauer: 20 min Siehe Programm 21 Kombination aus aktiver Mobilisation des Fußgelenkes und Schmerzbehandlung Stimulationsart Parameter Beschreibung Muskelstimulation und Gate Control Frequenz: Kanal und : 45 Hz Frequenz: Kanal und : 90 Hz Impulsbreite: 300 μs Aufstiegsrampe: 3 s Arbeitszeit: 1 s Abstiegszeit: 1 s Pause: 6 s Dauer: 20 min Siehe Programm 21 Programm 25 + U25: Hemiparese Schulterschmerz Stimulationsart Parameter Beschreibung Muskelstimulation und Gate Control Frequenz: Kanal und : 45 Hz Frequenz: Kanal und : 90 Hz Impulsbreite: 250 μs Aufstiegsrampe: 2 s Arbeitszeit: 6 s Abstiegszeit: 2 s Pause: 10 s Dauer: 20 min Siehe Programm 21 23 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Technische Informationen Neueinstellungen, Änderungen und Reparaturen des EMP 4 ECO + Verantwortlich für die Sicherheit und Leistung des EMP 4 ECO + betrachtet sich der Hersteller nur, wenn Neueinstellungen, Änderungen und Reparaturen durch von ihm ermächtigte Personen ausgeführt werden und das EMP 4 ECO +in Übereinstimmung mit der Gebrauchsanweisung betrieben wird. Gewährleistung Es gelten die gesetzlichen Gewährleistungsrechte gemäß BGB. Garantie Auf das Gerät EMP 4 ECO + gewährt der Hersteller eine Garantie von 12 Monaten ab Datum der Übernahme durch den Endkunden. Die Garantie gilt nicht: »» für Verschleißteile und Verbrauchsmaterial wie beispielsweise Elektroden, Batterien und Anschlusskabel »» im Falle von Schaden, die auf unsachgemäßer Bedienung beruhen »» für Mangel, die dem Kunden bereits bekannt waren »» bei Eigenverschulden des Kunden. Pflege und Reinigung Für das EMP 4 ECO + sind keine besonderen Pflege- oder Reinigungsmittel nötig. Das EMP 4 ECO + sowie die Elektrodenkabel können mit einem weichen, fusselfreien Tuch gereinigt werden. Es ist unbedingt darauf zu achten, dass keine Feuchtigkeit in das Innere des Gerätes gelangt. Sollte trotzdem Feuchtigkeit eingedrungen sein, so muss das Gerat vor erneuter Anwendung einer sicherheitstechnischen Kontrolle unterzogen werden. Batterierücknahme und Entsorgung Im Zusammenhang mit dem Vertrieb von Produkten, welche Batterien, zu denen auch Akkumulatoren gehören, enthalten, sind wir gesetzlich verpflichtet, Sie gemäß § 18 Abs. 1 des Batteriegesetzes (BattG) auf Folgendes hinzuweisen: Durch das Mülltonnensymbol ( ) werden schadstoffhaltige Batte- 24 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ rien gekennzeichnet sowie der Umstand, dass Batterien nicht über den Hausmüll, sondern fachgerecht entsorgt werden müssen. Unter dem Mülltonnensymbol ist die chemische Bezeichnung des Schadstoffes angegeben. Sie sind zur Rückgabe von Altbatterien gesetzlich verpflichtet. Sie können Altbatterien an einer kommunalen Sammelstelle oder im Handel vor Ort abgeben. Auch wir sind als Vertreiber von Batterien zur Rücknahme von Altbatterien verpflichtet, wobei sich unsere Rücknahmeverpflichtung auf Altbatterien der Art beschränkt, die wir als Neubatterien in unserem Sortiment führen oder geführt haben. Altbatterien vorgenannter Art können Sie daher entweder ausreichend frankiert an uns zurücksenden oder sie direkt an unserem Versandlager unter der folgenden Adresse unentgeltlich abgeben: schwa-medico GmbH, Wetzlarer Straße 41-43, 35630 Ehringshausen Mit welchen Symbolen schadstoffhaltige Batterien gekennzeichnet sind, entnehmen Sie bitte der folgenden Abbildung: Batterie enthält mehr als 0,002 Masseprozent Cadmium Batterie enthält mehr als 0,0005 Masseprozent Quecksilber Batterie enthält mehr als 0,004 Masseprozent Blei Sicherheitstechnische Kontrollen Bei gewerblicher oder wirtschaftlicher Nutzung sind im Abstand von 24 Monaten sicherheitstechnische Kontrollen (nach § 6 MPBetreibV) für das EMP 4 ECO + durchzuführen. Die sicherheitstechnischen Kontrollen umfassen: 1. Prüfung der Begleitpapiere auf Vorhandensein der Gebrauchsanweisung und des Medizinproduktebuches 2. Prüfung der Ausstattung auf Vollständigkeit 3. Sichtprüfung · auf mechanische Beschädigung · aller Leitungen und Steckverbinder auf Beschädigung 4. Funktionelle Sicherheit · Prüfung der Ausgangssignale an einem Lastwiderstand von 1 kΩ (Strom und Spannung) · Prüfung der Ausgangssignale an einem ANSI Lastwiderstand (Strom und Spannung) · Prüfung der Frequenz · Prüfung der Impulsbreite 25 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Die Bewertung der Sicherheit des EMP 4 ECO +muss durch eine Fachkraft mit elektrotechnischen und gerätebezogenen medizintechnischen Kenntnissen erfolgen. Im Medizinproduktebuch sind die Kontrollen mit Datum und Namen der ausfuhrenden Person zu vermerken. Kombination mit Originalzubehör Im Rahmen der CE-Kennzeichnung als Medizinprodukt darf das EMP 4 ECO + ausschließlich mit den in der Gebrauchsweisung aufgeführten Elektroden und Kabeln kombiniert werden. Andernfalls können wir nicht für die Sicherheit des Anwenders und für die Garantie des Gerätes aufkommen. Zubehör Selbstklebeelektroden Technische Daten Zusammensetzung: Lebensdauer: Farbe: Hersteller: Leitfähige und klebefähige Masse 30-50 Anwendungen Grau/schwarz Pierenkemper GmbH Anwendung: Die Elektroden werden direkt auf die angegebenen Hautstellen aufgeklebt. Nicht auf offene Wunden kleben! Pflege: Die Elektroden sollten aus hygienischen Gründen von nur einem Patienten angewandt werden. Bitte kleben Sie die Elektroden nach jedem Gebrauch auf die Folie zurück und stecken Sie diese in den Beutel. Bei sachgemäßer Anwendung sind diese 30-50 Mal benutzbar. Art.-Nr. 281000 282000 283400 283600 283000 283100 Artikel Stimex, rund 32 mm Ø Stimex, rund 50 mm Ø Stimex, 50 x 50 mm Stimex, 50 x 90 mm Stimex, 50 x 130 mm Stimex, 80 x 130 mm Menge 4 Stück 4 Stück 4 Stück 2 Stück 2 Stück 2 Stück 26 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Vaginal- und Analsonden Art.-Nr. Artikel 101066 Vaginalsonde V2B Menge 1 Stück 103045 1 Stück Analsonde 12C TL1R 103044 Analsonde TL1R 1 Stück 12 18 mm Ø 101509 4 5 5 5 25 Sonogel f. Sonden Länge 65 mm 1 Stück Kabel 106351 106352 106353 106354 Kabel Typ 5.15 (schwarz) Kabel Typ 5.16 (grau) Kabel Typ 5.17 (rot) Kabel Typ 5.18 (gelb) 1 1 1 1 Art.-Nr. Artikel 101062 Ladegerät für EMP4ECO+ Menge 1 27 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ STIMEX-TEX Anwendung: Befeuchten Sie die STIMEX TEX-Manschetten und legen Sie diese um Arm oder Bein an (hineinschlüpfen). Nicht auf offene Wunden anbringen! Pflege: Die Elektroden können mit lauwarmem Wasser per Handwäsche gereinigt werden. Lassen Sie diese lufttrocknen (nicht auf einen Heizkörper legen). Art.-Nr. Beschreibung 107049 STIMEX-TEX 1-20, 1 Anschluss (ca. 23-30 cm ø) 107051 STIMEX-TEX 1-30, 1 Anschluss (ca. 28-40 cm ø) 107052 STIMEX-TEX 1-35, 1 Anschluss (ca. 32-55 cm ø) 107053 STIMEX-TEX 2-20, Ellbogen 2 Anschlüsse (ca. 23-30 cm ø) 107054 STIMEX-TEX 2-35, Knie 2 Anschlüsse (ca. 32-55 cm ø) Menge 2 2 2 2 2 Lieferumfang Art.-Nr. 101060 106351 106352 106353 106354 283400 101062 101707 Artikel EMP 4 ECO + Kabel Typ 5.15 (schwarz) Kabel Typ 5.16 (grau) Kabel Typ 5.17 (rot) Kabel Typ 5.18 (gelb) Elektroden 50 x 50 mm (VPE 4 Stück) Ladegerät Aufbewahrungskoffer Gebrauchsanweisung Menge 1 1 1 1 1 2 1 1 1 28 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Elektrodenanlage für die Rehabilitationsprogramme P11 ; P12 ; P13 ; P14 ; P15 ; P16 P11 Krampfbehandlung P12 Atrophie obere Extremitäten Handbeuger Handstrecker Biceps Trapezius LWS Latissimus Bauch Gesäß P13 Atrophie untere Extremitäten P14 Kräftigung obere Extremitäten P15 Kräftigung untere Extremitäten P16 Venöser Rückfluss 29 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Beinstrecker Beinbeuger Fußheber P21 ; P22 P23 ; P24 ; P25 Zweiköpfiger Wadenmuskel Bei den aktiven Mobilisationsprogrammen achten Sie bitte darauf, dass die Kanäle und im Muskelstimulation Modus arbeiten und die Kanäle und im kontinuierlichen Schmerztherapiemodus. Programm 21 Kombination aus aktiver Mobilisation des Handgelenks + Schmerzbehandlung: Platzieren Sie die Kanäle und auf den Beuger und Strecker Muskel und die Kanäle und direkt auf das Gelenk. Programm 22 Kombination aus aktiver Mobilisation des Ellbogens + Schmerzbehandlung: Platzieren Sie die Kanäle und auf den Trizeps und/oder Bizeps und die Kanäle und direkt auf das Gelenk. Programm 23 Kombination aus aktiver Mobilisation des Kniegelenkes + Schmerzbehandlung: Platzieren Sie die Kanäle und auf den Quadizep und/oder Oberschenkelflexoren und die Kanäle und direkt auf das Kniegelenk. Programm 24 Kombination aus aktiver Mobilisation des Fußgelenkes + Schmerzbehandlung: Platzieren Sie die Kanäle und auf den vorderer Schienbeinmuskel und/oder Wadenmuskel und die Kanäle und direkt auf das Fußgelenk. Programm 25 Kombination aus aktiver Mobilisation des Schultergelenkes + Schmerzbehandlung: Platzieren Sie die Kanäle und auf den Musculus supraspinatus und/oder Deltamuskel und die Kanäle und direkt auf das Schultergelenk. 30 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Elektrodenanlage für die dynamische Stimulation in Schmerztherapie P1 ; P3 ; P9 ; P20 P1 Lumbales Schmerzsyndrom P3 Cervicobrachialgie Beinbeuger Wade Beinbeuger und Zweiköpfiger Wadenmuskel Rücken P9 Dynamische Massage P20 Muskelentspannung Quadrizeps Rücken (lumbal) Rücken und Oberschenkel 31 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Elektrodenanlage für die Schmerztherapie P2 ; P4 ; P5 ; P6 ; P7 ; P8 ; P10 P2 Lumboischialgie (Kanal 1 paravertebral im LendenwirbelBereich, Kanal 2 direkt auf dem Ischias Nerv) Nacken Trapezius Schulter Ellenbogen Hüfte Knie P4 Chronische Schmerzen P5 Gate Control (Kanal 1:100 Hz) + Endorphinausschüttung (Kanal 2: 2Hz) P6 Gonarthrose Coxarthrose P7 Epicondylitis P8 Algodystrophie P10 Klassiche Gate Control (120 Hz) 32 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Elektrodenanlage für die Schmerztherapie P2 ; P4 ; P5 ; P6 ; P7 ; P8 ; P10 P2 Lumboischialgie (Kanal 1 paravertebral im LendenwirbelBereich, Kanal 2 direkt auf dem Ischias Nerv) Lumboischialgie P4 Chronische Schmerzen P5 Gate Control (Kanal 1:100 Hz) + Endorphinausschüttung (Kanal 2: 2Hz) P6 Gonarthrose Coxarthrose P7 Epicondylitis P8 Algodystrophie P10 Klassiche Gate Control (120 Hz) Handgelenk Fußgelenk 33 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Elektrodenanlage für die neurologische Inkontinenz nach der SPI Stimulation (N. Tibialis posterior Stimulation) P17 Elektrodenanlage für die Inkontinenzbehandlung mit Sonden P18 ; P19 Vaginalsonde Analsonde 34 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ M edizinp r od u kte b u c h (§ 7 MPBetreibV) G e r äte -stammdaten (nach § 8 MPBetreibV) Geräteart Gerät zur Stimulation von Muskeln und Nerven Gerätebezeichnung EMP 4 ECO+ Klassifizierung/Gerätetyp II a CE Kennzeichnung| 0434 Seriennummer Hersteller Wuxi Jiajian Medical Instruments Co.,Ltd, Qinghong Rd. Wuxi City, China Vertrieb schwa-medico GmbH, Wetzlarer Str. 41-43, 35630 Ehringshausen Anschaffungsjahr Standort / Betreiber Inventar-Nr. Sicherheitstechnische Kontrollfrist 24 Monate e rst w e rte Ausgangsstrom (max.) Frequenz (max.) Impulsbreite (max.) alle angegebenen Werte im Toleranzbereich 100 mA an Last 1 kΩ reell 120 Hz 500 µs ± 15 % F unktionspr ü f u ng (nach § 5 Abs. 1 MPBetreibV) am durch Unterschrift E in w eis u ngen (nach § 5 Abs. 1 MPBetreibV) Verantwortlicher Datum Name der eingewiesenen Person Unterschrift P e rsonal (nach § 5 Abs. 1 MPBetreibV) ✃ Datum Einweiser Name der eingewiesenen Person Unterschrift einzelbeschreibung der Kontrollen 1. 2. 3. 4. Prüfung der Begleitpapiere auf Vorhandensein der Gebrauchsanweisung und des Medizinproduktebuches. Prüfung der Ausstattung auf Vollständigkeit. Sichtprüfung – auf mechanische Beschädigung – auf Vollständigkeit und Vorhandensein aller Beschriftungen und Markierungen – aller Leitungen und Steckverbinder auf Beschädigung Funktionelle Sicherheit – Prüfung der Ausgangssignale an einem Lastwiderstand von 1 Ω (Strom und Spannung) – Prüfung der Frequenzen – Prüfung der Modulationstiefe Sicherheitstechnische Kontrollen Datum durchgeführt durch (Person / Firma) I nstand halt ungsmassnahmen Datum durchgeführt durch (Person / Firma) Datum Beschreibung der Art und Folgen Ergebnis Unterschrift (nach § 4 MPBetreibV) Kurzbeschreibung der Maßnahme F u nktionsstör u ngen Datum (nach § 3 MPBetreibV) Behörde Hersteller ✁ Meld ung ü be r Vo r kommnisse 37 schwa-medico Operating Manual - EMP 4 ECO+ Content General Information.........................................38 Description of the EMP4 ECO +.......................39 Description of the Symbols..............................39 Technical Specifications....................................40 Operating the EMP4 ECO +.............................41 Setting of Intensitiy Levels...............................45 Principle of Dynamic Stimulation....................46 Short Instruction...............................................47 Description of the Pre-Set Programs...............48 Technical Information.......................................58 Accessories........................................................60 Delivery Content...............................................62 Electrodes Position...........................................63 Program Overview............................................70 38 schwa-medico Operating Manual - EMP 4 ECO+ General Information Intended Use The EMP4 ECO + device has been designed for the generation of transcutaneous stimulation of muscles and nerves an humans and may not be used for any other purposes. Safety Instructions Please read the operating instructions carefully before using the EMP4 ECO +. To ensure safe use of the EMP4 ECO +: Only use the EMP4 ECO + with original accessories. Keep the EMP4 ECO + away from water or other liquids. Do not drop the EMP4 ECO +, do not use it inappropriately or expose it to extreme temperatures or high levels of humidity (not less than 10°C or more than 40 °C or a relative humidity of more than 90 %). Do not use the EMP4 ECO + if it is not working properly or if it has been damaged in any way. Be careful when using the EMP4 ECO + near or on children. Always store the EMP4 ECO + in its case to protect it from damage and dust. The size of the electrodes are to be not less than 2 cm². Caution ! Patients with medical implants (e.g. cardiac pacemakers) should consult their doctor before using the EMP4 ECO +. The EMP4 ECO + may only be connected to one person at any one time. Long treatment sessions are subject to limited periods of time. Do not extend the treatment time of the fixed programs. After a treatment session, wait for several hours before using the EMP4 ECO + again. Warning ! The simultaneous use of EMP4 ECO + and a high frequency surgery unit can cause burns underneath the electrodes. The application of the unit close to a shortwave or microwave device can cause variations in the output values of the EMP4 ECO +. In addition, portable or mobile high frequency communication devices may affect the operation of electrical medical devices. 39 schwa-medico Operating Manual - EMP 4 ECO+ Description of the EMP4 ECO + 1. Display 2. Program selection key 3. To enter the user mode and to pause the stimulation 4. Keys to adjust the intensities of all channels Increasing intensity Decreasing intensity 5. ON/OFF key 6. Output sockets for the cables 7. Output socket for the battery charger 8. ON/OFF commutator 1 2 3 4 5 6 7 6 8 Description of the Symbols Attention: Read accompanying documents, especially user manual! 0434 By labelling with CE mark, the manufacturer asserts that the product fulfills all relevant requirements of the respective EC Directives. A conformation assessment process has been successfully completed. The identification number in respect of the conformation assessment process is given in accordance with the CE labelling of the relevant notified body. Type BF applied part 40 schwa-medico Operating Manual - EMP 4 ECO+ Serial Number Catalogue number Date of manufacture Manufacturer Environment Do not dispose of the appliance with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. By doing this you will help to protect the environment. Technical Specifications Nerve and muscle stimulator with 2x2 channels (4x100 mA max.) electrically insulated channels, constant current characteristic, 25 integrated pre-set programs and 20 user programs. Output current Frequency range Impulse width Current consumption U Power supply Dimensions Weight 100 mA (with an actual resistor of 1kΩ) 1-120 Hz 50-500 μs 15 mA UI I Rechargeable battery Ni-MH 4.8 V 120 x 75 x 35 mm approx. 250 g t t t Impulse form: Biphasic symmetric impulses with pause With 1 kΩ load real With ANSI standard load U U t t U U t 41 schwa-medico Operating Manual - EMP 4 ECO+ Operating the EMP4 ECO + Connecting the Cables and the Electrodes Connect the electrodes with the cable(s) (always 2 electrodes per cable). Connect the cables to the EMP4 ECO + on sockets no. 6. Place the electrodes on the desired area (see electrode placement) Switching ON the EMP4 ECO + Switch the commutator (no. 8) to the ON position. Press the key to start the device. The program shown on the display is the last program used. The device automatically switches off after 2 minutes of disuse. If the display shows a key symbol on the upper left side, the EMP4 ECO + has previously locked a specific program (see chapter locking the key pad). Selecting a Program Ensure that the EMP4 ECO + has not been locked on one program. Select a program by pressing the P key. To scroll through the programs, press the P key as often as necessary until you have selected the program of your choice. To return to the previous program, press one of the keys. Starting the Stimulation First check if you have selected the right program and if cables and electrodes are well connected and well positioned on the skin. Start the stimulation by increasing the intensity with the key of the channel(s) connected to the electrodes. Setting the Intensity Adjust the intensity of the channels (black) and left and keys. Adjust the intensity of the channels (grey) and the right and keys. Increase the intensity with the keys. Decrease the intensity with the keys. (red) by using the (yellow) by using 42 schwa-medico Operating Manual - EMP 4 ECO+ By keeping the intensity keys pressed, the intensity will increase/ decrease more rapidly. The intensity of each channel is displayed on the screen. The intensity can be set between 0 and 100 mA. Caution! The stimulator automatically locks the intensity to the set level after 5 seconds. To adjust the intensity you firstly need to decrease the intensity. The intensity can then be increased again. If electrodes are not or not correctly connected to the stimulator, you will not be able to set the intensity to more than 10 mA. The same result will occur if electrodes are old or the cables broken. Stopping the Stimulation You can stop the stimulation at any time by pressing the P key or the key for 2 seconds. When the therapy time is completed, the stimulation stops automatically. Pausing the Stimulation You can temporarily stop the stimulation by pressing the E key during the stimulation. The word “PAUSE” then flashes on the display. You can then adjust the position of the electrodes. Press the E key again to re-start the stimulation. The intensity levels slowly increase to the level set before the pause. 43 schwa-medico Operating Manual - EMP 4 ECO+ Creating User Programs (U1 to U20 only) Choose one program between U1 and U20. Press the E key to access the Programing mode. The parameters to be changed are flashing. You can modify them by pressing the and keys. Switch to the next parameter by pressing the E key. The frequency, the pulse width and the time can be modified in the free programs. The parameters of the user programs can be modified as follows: U1, U3, U4, U9, U20 Frequency 20-120 Hz Pulse width 70-500 µs Time 1-99 min U2, U5 (TENS) 80, 90, 100, 110, 120 Hz Frequency channel (black) and (red) Frequency channel (grey) 2, 5, 10 Hz and (yellow) Pulse width 70-500 µs Time 1-99 min U6 Time 1-99 min U7, U8 Maximum Frequency 10-120 Hz Minimum Frequency 2 Hz Pulse width 70-180 µs Time 1-99 min U10, U11, U17 Frequency 1-120 Hz Pulse width 70-500 µs Time 1-99 min U12, U13, U14, U15, U16, U18, U19 Frequency 20-120 Hz Pulse width 70-500 µs Rising ramp 1-4 s Working time 1-25 s Pause 1-25 s Time 1-99 min 44 schwa-medico Operating Manual - EMP 4 ECO+ Switching-OFF the Stimulator Press the key for one second to stop the stimulation and press key a second time to turn OFF the EMP 4 ECO +. If the battery level is too low or if the stimulator has not been used for the previous 2 minutes, it turns off automatically. Charging the Battery The battery level is shown on the display with a battery symbol with 4 lines. If the battery level is too low, the stimulator switches off automatically and cannot be turned on again. The battery then needs to be re-charged. Only use the delivered charger (Item no. 101062) to charge the battery of the EMP4 ECO +.. Output socket for the battery charger Charger Switch the commutator to the OFF position. Connect the charger with the EMP4 ECO +. Connect the charger to the mains circuit. The diode on the charger illuminates in red. Charge the EMP4 ECO + until the diode on the charger illuminates in green. The battery is fully charged if the light on the charger appears in green. Disconnect the charger from the main circuit and from the stimulator. Place the charger back in the storage case. Important! Do not forget to switch the commutator to ON again after charging. 45 schwa-medico Operating Manual - EMP 4 ECO+ Setting of Intensity Levels Do not try to achieve a higher and higher level of intensity. Set the intensity in such a way that you get a comfortable feeling during the stimulation. Increase the intensity carefully to a maximum tolerable and then reduce it slightly step by step to a comfortable level. Note that the intensity settings change depending on the stimulation area and the time. This is normal and can be explained as follows: Resistance of the skin: Dry skin has a lower conductivity level than damp skin (due to sweating). The skin does not show the same resistance to linear current on all parts of the body. For example, the resistance level of horny skin can be twice that of the skin in the hollow of the knee. The innervation differs greatly according to the area of the body. This results in a difference of sensitivity. Volume of the muscle mass: If you stimulate muscles with a high volume you will automatically need to set a higher intensity than for the stimulation of small muscles. Muscle fatigue: A tired muscle will only tolerate a lower intensity. Age of electrodes: Self-adhesive electrodes do not last forever. You can use them up for up to 60 stimulation sessions. This depends on the quality of the electrodes but also on the skin of the user. Old electrodes have a higher resistance and their conductivity levels decline. It is important to replace electrodes regularly. Adaption to the current: The nerves adapt rapidly to the current. It is normal to feel “less current” after a few minutes of stimulation with specific parameters. In such a case feel free to increase the intensity in order to get the best results. Frequency and pulse width: Frequencies and pulse widths differ depending on the programs. Therefore the intensity cannot be set at the same lever for all the programs even if the electrodes are placed in the same position. The higher the frequency is set, the lower you will be able to set the intensity. The higher the pulse width is set, the lower you will be able to set the intensity. 46 schwa-medico Operating Manual - EMP 4 ECO+ Principle of Dynamic Stimulation The dynamic stimulation principle is based on the fact that the stimulation is not applied simultaneously on all channels. Dynamic stimulation generates a wave movement of the stimulation impulse which moves to and fro between the electrode pairs and therefore attains enhanced reproduction of the massaging effect. Dynamic stimulation creates for the user a more pleasurable experience than with classic neuro-muscular stimulation. The consecutive four channel distribution of the electrical current produces good results in respect of both pain alleviation and muscular relaxation. The application of dynamic stimulation for lymph drainage accentuates the effect of the wave type muscular contraction. Kanal 1 Electrode Positions for dynamic Stimulation Sideways Kanal 1 Kanal 2 Kanal 4 Kanal 3 3 Channel 4 Sideways wave: E.g gluteus, stomach musclesKanal 4 Kanal 4 Kanal 1 Kanal 3 Kanal 4 Kanal 4 Kanal 2 Channel 2 Kanal 3Channel 3 Kanal 3 Channel 3 Kanal 2Channel 2 Kanal 4 Channel 4 Kanal 1Channel 1 Dynamic stimulation on legs: Place one electrode of each channel on each legKanal (size2 5x9 cm). All anodes should be on one leg and all cathodes on the other leg. Kanal 1 Dynamic stimulation on the back: Place one electrode of each channel on each side of the spinal column (size 5x9 cm). Place all anodes on one side and all cathodes on the other side. Kanal 3 Kanal 3 4 Falling/Rising wave: E.g. back, legs Kanal 2 Kanal 2 Kanal 4Channel Kanal 1 Kanal 3 Channel 1 Kanal 2 2 Rising Channel Kanal 1 Kanal 3 Kanal 2 1 Channel Kanal 4 Falling Kanal 4 Kanal 1 Channel Kanal 3 Kanal 1 Kanal 2 Important note If you use electrodes with two connectors, always connect them to the same pole colour of the cables (either both blue or both red). 47 schwa-medico Operating Manual - EMP 4 ECO+ Short Instruction Short Instruction Important ! Connect the electrodes with the cable(s) (always 2 electrodes per cable). Connect the cables to the device. Place the electrodes on the desired area. Switch ON/OFF the unit Program choice Press the P key to select a program. Intensity setting Intensity channel 1 channel 2 Intensity channel 3 channe l 4 increase the intensity increase the intensity decrease the intensity decrease the intensity Caution! The intensity is automatically interlocked after 5 s. First decrease the intensity to increase again the intensity. Stop stimulation Press the P key for 2 seconds to stop the stimulation. 48 schwa-medico Operating Manual - EMP 4 ECO+ frequency Hz Description of the Pre-Set Programs intensity 100 } T = 1/f build-up phase pulse width Program P1 + U1: Low Back Pain Type of time stimulation Parameter channel 2 50 Gate control 80 Hz - dynamic stimulation (slow) time s 7,5 15 Frequency: 80 Hz Pulse width: 150 μs Time: 20 min intensity mA Rising 70ramp: 1 s working phase Falling ramp: 1 s pause phase Rising phase Falling phase ld-u bui ase frequency Hz 100 wn ph Symbols on the display during stimulation time Description Channel 1 pp has run-do e intensity run-down phase run-down phase 2 7 time s 8 The 4 channels are working with the same frequency and pulse width. intensity phase 1 50 phase 2 2 10 20 30 time min frequency Hz intensity I mA 3 time s 6 pulses 0,25 0,5 0,75 1 } } working phase intensity time s channel 2 pause phase run-down p 50 intensity mA ase pause phase 100 70 wn ph working phase frequency Hz time intensity run-do working phase Symbol on the display during stimulation Description Gate Control 80 Hz + 2 Hz Endorphinausschüttung intensity Frequency ChannelT = 1/fand : 80 Hz time t s pulse width and : 2 Hz Frequency Channel Pulse width: 200 μs Time: 20 min } phase 2 75 µs 200 µs pha se Stimulationsart Parameter 50 2 T = 1/f Lumbosciatica -up Program P2 + U2: phase 1 bui ld 100 time 2 7 70 time 8 Channel 1 time frequency Hz 100 intensity phase 1 50 phase 2 2 10 20 30 time min 49 schwa-medico Operating Manual - EMP 4 ECO+ frequency Hz intensity 100 } T = 1/f build-up phase pulse width run-down phase run-down phase Program P3 + U3: Cervicobrachial Syndrome 50 Gateintensity control 80 Hz - dynamic stimulation (fast) time s 15 Frequency: 80 Hz T = 1/f7,5 pulse width Pulse width: 150 μs Time: 20 min intensity mA Rising 70ramp: 0.2 s time working phase Falling ramp: 0.2 s pause phase Rising phase Falling phase frequency Hz 100 } Type of time stimulation Parameter channel 2 has pp ld-u bui ase time s channel 2 intensity 2 8 7 The 4 channels are working with the same frequency and pulse width. intensity mA 70 Channel 1 intensity b frequency Hz 100 50 wn ph Symbols on the display during stimulation time Description Channel 1 run-down p run-do e intensity phase 1 time 50 phase 2 2 10 20 30 time min time Chronic Pain 3 6 pulses 0,25 0,5 0,75 1 s time min time t s intensity I mA time s pause phase ase pause phase Symbols on the display during stimulation: Description time Burst 2 Hz endorphin release frequency Hz Frequency: 100 Hz 100 1 Pulse width:phase150 μs Time: 20 min 50 intensity phase: 0.25 s Working phase 2 Pause:700.25 s 2 working phase 6 Working phase3 Pause wn ph working phase 30 run-do working phase 20 pha se Type of stimulation time Parameter s phase 2 2 phase 2 10 -up 50 bui ld Program 4 + U4: T = 1/f 75 µs 200 µs } 2 } phase 1 intensity phase 1 intensity I 50 mA frequency Hz 100 frequency Hz 100 pulses 2 8 7 working phase time working phase pause phase 0,25 0,5 0,75 1 time s intensity 70 50 schwa-medico Operating Manual - EMP 4 ECO+ Gate Control + Endorphin Release Parameter Symbol on the display during stimulation Description Gate control on channel 1 + endorphin release on channel 2 Frequency channel (black) and (red)(red): 100 Hz Frequency channel (grey) and (yellow): 2 Hz Pulse width: 200 μs intensity Time: 20 min T = 1/f } Type of stimulation frequency Hz 100 pulse width run-down 50 Channel (black) and (red) are working with a 100 time Hz frequency (80-120 Hz in the user mode). Channel (grey) and (yellow) are working with a 2 Hz freintensity quency (0.5-10 HzTin the user mode). = 1/f intensity } Program 5 + U5: pulse width channel 2 frequency Hz 100 intensity mA 70 run-down p 50 Channel 1 time time 70 intensity frequency Hz 100 Gonarthrosis / Coxarthrosis phase 1 Type of stimulation Parameter phase 1 Parameter phase 2 Symbols on the display Description Channel 1 Han 50 Frequency: 100 Hz time phase 2 Pulse width: 100 μs 2 time min 10 20 30 Time: 3 s frequency Frequency: 2 Hz Hz 100 frequency phase 1 Pulse Hz width: 200 μs 100 Time: 350s phase 1 Time: 2050 min Phase 1 and phase 2 are alternating every 3 seconds. phase 2 2 time min 10 phase 2 20 30 Phase 1 2 time s Phase 2 3 6 frequency Hz 100 intensity intensity I mA intensity I mA phase 1 intensity pulses 70 50 2 b Program 6 + U6: intensity mA channel 2 intensity working phase phase 2 working phase 3 0,25 time s 6 pause phase 0,5 0,75 1 time s intensity pulses 70 working phase working phase 51 schwa-medico Operating Manual - EMP 4 ECO+ Program 7 + U7: Epicondylitis Type of stimulation Parameter Symbols on the display during stimulation Description intensity frequency Hz 100 T = 1/f } Modulation Minimum frequency: 2 Hz (Pulse width: 200 µs) Maximum frequency: 80 Hz (Pulse width: 100 µs) Duration of the modulation: 7.5 s Time: 20 min Rising ramp: 0,2 s Falling ramp: 0,2 s Rising phase Falling phase build-up phase pulse width run-down phase run-down phase 50 time 7,5 intensity mA phase 1 50 phase 2 2 intensity 10 20 Symbols on the display during stimulation time min Description 30 } frequency Hz pulse width e has pp build-up phase intensity I phase mArun-down 50 phase 1 run-down phase T = 1/f 75 µs 200 µs } 100 time frequency Hz 100 T = 1/f } frequency Hz 100 pause phase Modulation Minimum frequency: 2 Hz (Pulse width: 148 µs) Maximum frequency: 80 Hz (Pulse width: 70time µs) s 8 2 7 Duration of the modulation: 7.5 s Time: 20 min intensity Rising ramp: 0.2 s Falling ramp: 0.2 s Rising phase Falling phase ase time working phase wn ph Type of stimulation Parameter Channel 1 70 ld-u Algodystrophy run-do Program 8 + U8: bui channel 2 intensity time s 15 time 50 7,5 phase 2 2 3 6 channel 2 intensity time s time s 15 time t s intensity mA 70 ld-u p bui working phase working phase pause phase time bui working phase ld-u p pha se 70 2 7 ase ase wn ph n-down ph ru Channel 1 pulses pha s e working phase run-do intensity 8 pause phase pause phase time s time 52 schwa-medico Operating Manual - EMP 4 ECO+ frequency Hz intensity 100 } T = 1/f build-up phase pulse width Program 9 + U9: Anti-Adaptation – Dynamic Stimulation 50 Type of time stimulation Parameter channel 2 Dynamic stimulation (fast) 7,5 Frequency: 80 Hz Pulse width: 150 μs Time: 20 min intensity mA Rising 70ramp: 0.5 s working phase Falling ramp: 0.5 s Rising phase Falling phase ld-u bui wn ph 2 pause phase ase frequency Hz 100 pp has run-do Symbols on the display during stimulation time Description Channel 1 time s 15 e intensity run-down phase run-down phase 7 time s 8 The 4 channels are working with the same frequency and pulse width. intensity phase 1 50 10 20 30 time min frequency Hz time intensity I mA 100 0,25 0,5 0,75 1 } pause phase ase pause phase working phase wn ph working phase 70 run-do working phase Symbol on the display during stimulation Description pha se pulses time t s -up time s 6 TENS Frequency: 120 Hz Pulse width: 150 μs Time: 20 min Working phase: 0.25 s Pause: 0.25 s intensity intensity time s 2 } phase 2 3 75 µs bui ld Type of stimulation Parameter 50 2 T = 1/f Classic Gate Control 120 Hz 200 µs } Programphase 101 + U10: T = 1/f 7 8 time frequency Hz 100 pulse width run-down ph 50 time intensity intensity mA channel 2 70 Channel 1 bu phase 2 2 time 53 schwa-medico Operating Manual - EMP 4 ECO+ Program 11 + U11: Treatment of Contractures Type of stimulation Parameter Symbol on the display during stimulation Description TENS Frequency: 1 Hz Pulse width: 150 μs Time: 20 min Working phase: 0.25 s Pause: 0.25 s See picture program P10 Muscle Stimulation Programs Symbols on the display Rising phase Working phase Pause Program 12 + U12: Atrophy Upper Extremities intensity Type of stimulation Parameter } T = 1/f pulse width time Description channel 2 intensity frequency Hz Muscle stimulation 100 Frequency: 35build-up Hz phase run-down phase150 μs Pulse width: 50 Rising ramp: 2 s Working phase: 3 s Pause: 9 s Time: 20 min run-down phase 7,5 time s 15 intensity mA 70 e has Channel 1 pause phase ase wn ph bui ld-u pp run-do working phase time 50 phase 2 10 frequency Hz 100 20 30 time min Description phase 1 8 time s intensity Muscle stimulation Frequency: 35 Hz Pulse width: 300 μs Rising ramp: 2 s Working phase: 3 s Pause: 9 s Time: 20 min intensity I SeemApicture program P12 T = 1/f 200 µs 75 µs } Type of stimulation Parameter phase 1 2 7 Atrophy Lower Extremities } Program 13 + U13: frequency Hz 100 2 time 54 schwa-medico Operating Manual - EMP 4 ECO+ Program 14 + U14: Muscle Strengthening Upper Extremities Type of stimulation Parameter Description Programm 15 + U15: Muscle Strengthening Lower Extremities Type of stimulation Parameter Description Programm 16 + U16: Muscle stimulation Frequency: 65 Hz Pulse width: 250 μs Rising ramp: 2 s Working phase: 4 s Pause: 8 s Time: 20 min See picture program P12 Muscle stimulation Frequency: 65 Hz Pulse width: 300 μs Rising ramp: 2 s Working phase: 4 s Pause: 8 s Time: 20 min See picture program P12 Venous Reflux Type of stimulation Parameter Description Muscle stimulation Frequency: 35 Hz Pulse width: 250 μs Rising ramp: 3 s Working phase: 5 s Pause: 10 s Time: 20 min See picture program P12 Program 17 + U17: Urge Incontinence Type of stimulation Parameter Description TENS Frequency: 10 Hz Pulse width: 180 μs Time: 15 min See picture program P10 55 schwa-medico Operating Manual - EMP 4 ECO+ Program 18 + U18: Mixed Incontinence Type of stimulation Parameter Description Program 19 + U19: Stress Incontinence Type of stimulation Parameter Description intensity Muscle stimulation Frequency: 50 Hz Pulse width: 180 μs Rising ramp: 2 s Working phase: 3 s Pause: 6 s Time: 15 min See picture program P12 frequency Hz T = 1/f } Muscle stimulation Frequency: 20 Hz Pulse width: 180 μs Rising ramp: 2 s Working phase: 4 s Pause: 4 s Time: 15 min See picture program P12 100 build-up phase pulse width run-down phase run-down phase Program 20 + U20: Relaxation – Dynamic Stimulation 50 Type of time stimulation Parameter channel 2 ld-u bui a wn ph 2 pause phase se frequency Hz 100 pp has run-do Symbols on the display during stimulation time Description Channel 1 time s 15 e intensity Dynamic stimulation (slow) Frequency: 120 Hz 7,5 Pulse width: 150 μs Time: 20 min intensity mA Rising 70ramp: 2 s working phase Falling ramp: 2 s Rising phase Falling phase 7 8 time s The 4 channels are working with the same frequency and pulse width. intensity phase 1 50 10 frequency Hz 30 time min time intensity I mA phase 1 T = 1/f 200 µs } 100 20 50 75 µs } phase 2 2 time 56 frequency Hz 100 2 7 time s 8 intensity schwa-medico Operating Manual - EMP 4 ECO+ phase 1 50 time Combination: Active wrist joint motion + pain management time min 2 10 20 30 Type of stimulation Parameter frequency Hz phase 1 } 100 Muscle stimulation and gate control Frequency channel (black) and (red): 45 Hz intensity I mA (yellow): 90 Hz Frequency channel T = 1/f (grey) and 75 µs 200 µs200 Pulse width: μs Rising ramp: 3 s Working phase: 1 s time t Falling ramp: 1 s s Pause: 6 s Time: 20 min 50 phase 2 2 3 time s 6 Description pulses } Program 21 + U21:phase 2 intensity bui working phase wn ph working phase ld-u pp has e working phase run-do Channel 70 and ase pause phase 0,25 pause phase 0,5 0,75 1 time s 2 7 time 8 frequency Hz intensity Channel and 100 } T = 1/f pulse width run-down ph 50 time intensity Combination: Active elbow joint motion + pain management channel 2 Type of stimulation Parameter Description Muscle stimulation and gate control 1 Frequency channel Channel (black) and (red): 45 Hz Frequency channel (grey) and (yellow): 90 Hz time Pulse width: 250 μs Rising ramp: 5 s Working phase: 1 s frequency Falling Hz 100ramp: 5 s Pause: 10 sphase 1 Time: 20 50 min See picture program P21 phase 2 2 10 20 30 70 intensity time min frequency Hz 100 intensity mA bu Program 22 + U22: intensity I mA phase 1 2 50 phase 2 2 3 6 time s 57 schwa-medico Operating Manual - EMP 4 ECO+ Program 23 + U2 : Combination: Active knee joint motion + pain management Type of stimulation Parameter Description Program 24 + U24: Combination: Active ankle joint motion + pain management Type of stimulation Parameter Description Program 25 + U25: Muscle stimulation and gate control Frequency channel (black) and (red): 45 Hz Frequency channel (grey) and (yellow): 90 Hz Pulse width: 300 μs Rising ramp: 5 s Working phase: 1 s Falling ramp: 5 s Pause: 10 s Time: 20 min See picture program P21 Muscle stimulation and gate control Frequency channel (black) and (red): 45 Hz Frequency channel (grey) and (yellow): 90 Hz Pulse width: 300 μs Rising ramp: 3 s Working phase: 1 s Falling ramp: 1 s Pause: 6 s Time: 20 min See picture program P21 Combination: Hemiparesis (shoulder) + pain management Type of stimulation Parameter Description Muscle stimulation and gate control Frequency channel (black) and (red): 45 Hz Frequency channel (grey) and (yellow): 90 Hz Pulse width: 250 μs Rising ramp: 2 s Working phase: 6 s Falling ramp: 2 s Pause: 10 s Time: 20 min See picture program P21 58 schwa-medico Operating Manual - EMP 4 ECO+ Technical Information Adjustments, Modifications and Repairs The manufacturer is only responsible for the safety and performance of the EMP4 ECO + when readjustments, alterations and repairs are carried out by authorized persons and when the EMP4 ECO + is used in accordance with the operating instructions. Warranty Legal right of warranty is applied according to German Civil Code. Guarantee The manufacturer issues a guarantee of 12 months from the date of purchase. The guarantee does not apply in the following cases: • Damage due to improper handling • Defects the customer is aware of on the date of purchase • Damage caused by the customer • For wearing parts and consumable supplies like, for instance, battery, cables and electrodes. Maintenance and Cleaning No special cleaning or care agents are required for the EMP4 ECO +. Clean the stimulator with a soft, lint-free cloth. Please ensure that no moisture permeates the stimulator. If moisture does permeate the stimulator, a technical check must be carried out before re-use. Battery Retraction and Disposal In connection with the sales of products which contain batteries or rechargeable batteries, we are obliged by law (battery law § 18, section 1) to advise you of the following: The dustbin symbol ( ) marks batteries with hazardous substances as well as the circumstance that batteries must not be disposed of in the household waste but professionally. The chemical term of the hazardous substance is below the dustbin symbol. You are obliged by law to return used batteries. You may render used batteries at municipal collecting points or in 59 schwa-medico Operating Manual - EMP 4 ECO+ local trade. We are also obliged to take back used batteries, whereat our obligation restricts to those which are or were part of our product range. Therefore, you may send back used batteries to us adequately stamped by mail or render these at our warehouse free of charge at the following address: schwa-medico GmbH, Wetzlarer Str. 41-43, 35630 Ehringshausen, Germany Please refer to the following figures to see the respective symbols of batteries with hazardous substances: Battery contains more than 0.002 % cadmium Battery contains more than 0.0005 % quicksilver Battery contains more than 0.004 % plumb Classification The EMP4 ECO + has been designed as a class IIa product in accordance with appendix IX of the Medical Device Directive 93/42/ EEC. Technical Check We recommend a technical check on the EMP4 ECO + every 24 months. This includes: 1. Confirming that user instructions have been included in the accompanying documentation. 2. Checking the equipment for completeness. 3. Visual check: - for mechanical damage - for damage to all cables and plugs / sockets 4. Functional Safety - Checking the output signals with a load resistance of 1 kΩ real current and voltage - Checking the frequency - Checking the pulse width These technical checks may only be performed by suitably qualified persons. The results must be documented with the date and name of the person carrying out the check. 60 schwa-medico Operating Manual - EMP 4 ECO+ Combination with Original Accessories The EMP4 ECO + is a CE marked medical device and may therefore only be used together with the accessories listed in the chapter Accessories of this manual. The manufacturer cannot guarantee the security of the stimulator if not used with original accessories. STIMEX Self-Adhesive Electrodes Accessories Compound: Manufacturer: conductive and bonding material Pierenkemper GmbH, Germany Application: Place self-adhesive electrodes directly on the appropriate skin treatment area, no special preparation of electrodes is necessary. See „Electrode Maintenance“ below to ensure the electrode’s effectiveness. Do not apply on broken skin ! Electrode maintenance: For hygienic reasons, self-adhering electrodes are for single patient use only. After every treatment session return electrodes to their original foil and store them in their plastic bag. To increase longevity, store the STIMEX electrodes in a cool area (e.g. refrigerator). Item no. 281000 282000 283400 283600 283000 283100 Size Stimex, round 32 mm Ø Stimex, round 50 mm Ø Stimex, 50 x 50 mm Stimex, 50 x 90 mm Stimex, 50 x 130 mm Stimex, 80 x 130 mm Quantity 4 4 4 2 2 2 Probes and Gel Vaginal and anal probe are only to be used with the incontinence programs of this unit. The probe may be used by one person only and in the interests of hygiene should not be shared with other persons. The probe is reusable if it has been cleaned and stored correctly after each treatment session. The probe should only be used on intact mucous membrane. Do not use the probe if it is damaged or if it does 61 schwa-medico Operating Manual - EMP 4 ECO+ not work correctly. Do not use the probe if the packaging is damaged. Clean the probe after each electrotherapy session with water and soap or clean it with 70% alcohol. Item no. Description 103025 Vaginal probe V2B Quantity 1 103045 Anal probe 12 C 1 TL1R 103044 Analprobe TL1R 1 12 18 mm Ø 101509 4 5 5 5 25 Sonogel for probes Länge 65 mm 1 Cables and Charger Item no. 106351 106352 106353 106354 Description Cable type 5.15 (black) Cable type 5.16 (grey) Cable type 5.17 (red) Cable type 5.18 (yellow) Quantity 1 1 1 1 Charger for EMP4 ECO + 1 101062 62 schwa-medico Operating Manual - EMP 4 ECO+ STIMEX-TEX Stimulation Sleeves Instruction: Moisten the inner side of STIMEX-TEX before every utilisation. Connect the STIMEX-TEX with the cable of the AmpliMove medical. Slip the STIMEX-TEX over the arm, elbow, foot, leg or knee. Do not apply STIMEX-TEX on wounds. Air-dry the STIMEX-TEX after every utilisation (not above a radiator). STIMEX-TEX may be washed by hand with cold water. Item no. 107049 107051 107052 107053 107054 Description STIMEX-TEX 1-20, 1 connector (approx. 23-30 cm ø) STIMEX-TEX 1-30, 1 connector (approx. 28-40 cm ø) STIMEX-TEX 1-35, 1 connector (approx. 32-55 cm ø) STIMEX-TEX 2-20, Elbow 2 connectors (approx. 23-30 cm ø) STIMEX-TEX 2-35, Knee 2 connectors (approx. 32-55 cm ø) Quantity 2 2 2 2 2 Delivery Content Item no 104064 106351 106352 106353 106354 101062 283400 101723 Description EMP4 ECO + Cable type 5.15 (black) Cable type 5.16 (grey) Cable type 5.17 (red) Cable type 5.18 (yellow) Charger for EMP4 ECO + STIMEX self-adhesive electrodes 50x50 mm Transport case Instruction manual Quantity 1 1 1 1 1 1 2 1 63 schwa-medico Operating Manual - EMP 4 ECO+ ELECTRODES POSITION REHABILITATION PROGRAMS P11 P12 P13 P14 P15 P16 Hand flexor Hand extensor Biceps Trapezius Back Latissimus Stomach muscles Gluteal muscles 64 schwa-medico Operating Manual - EMP 4 ECO+ ELECTRODES POSITION REHABILITATION, COMBINATION PROGRAMS P21 P22 P23 P24 P25 Leg extensor Leg flexor Foot flexor Foot extensor 65 schwa-medico Operating Manual - EMP 4 ECO+ ELECTRODES POSITION DYNAMIC PROGRAMS Pain Treatment with dynamic stimulation P1 P3 P9 P20 Leg extensor (quadriceps) Leg flexor Foot flexor (calf) Leg flexor and foot flexor Back Back Back and quadriceps 66 schwa-medico Operating Manual - EMP 4 ECO+ ELECTRODES POSITION PAIN TREATMENT PROGRAMS P2 P4 P5 P6 P7 P8 P10 Neck Trapezius Deltoid Elbow Hip Knee 67 schwa-medico Operating Manual - EMP 4 ECO+ ELECTRODES POSITION PAIN TREATMENT PROGRAMS P2 P4 P5 P6 P7 P8 P10 Lumbosciatica Wrist Ankle 68 schwa-medico Operating Manual - EMP 4 ECO+ ELECTRODES POSITION INCONTINENCE PROGRAMS P17 P18 P19 Vaginal probe Anal probe 69 schwa-medico Operating Manual - EMP 4 ECO+ 70 schwa-medico Operating Manual - EMP 4 ECO+ Program Overview Program P1 + U1 Low Back Pain Program P2 + U2 Lumbosciatica Program P3 + U3 Cervicobrachial Syndrome Program 4 + U4 Chronic Pain Program 5 + U5 Gate Control + Endorphin Release Program 6 + U6 Gonarthrosis / Coxarthrosis Program 7 + U7 Epicondylitis Program 8 + U8 Algodystrophy Program 9 + U9 Anti-Adaptation – Dynamic Stimulation Program 10 + U10 Classic Gate Control 120 Hz Program 11 + U11 Treatment of Contractures Program 12 + U12 Atrophy Upper Extremities Program 13 + U13 Atrophy Lower Extremities Program 14 + U14 Muscle Strengthening Upper Extremities Programm 15 + U15 Muscle Strengthening Lower Extremities Programm 16 + U16 Venous Reflux Program 17 + U17 Urge Incontinence Program 18 + U18 Mixed Incontinence Program 19 + U19 Stress Incontinence Program 20 + U20 Relaxation – Dynamic Stimulation Program 21 + U21 Combination: Active wrist joint motion + pain management Program 22 + U22 Combination: Active elbow joint motion + pain management Program 23 + U23 Combination: Active knee joint motion + pain management Program 24 + U24 Combination: Active ankle joint motion + pain management Program 25 + U25 Combination: Hemiparesis (shoulder) + pain management 71 schwa-medico Gebrauchsanweisung - EMP 4 ECO+ Programmübersicht Programm 1 + U1 Lumbales Schmerzsyndrom Gate Control Programm 2 + U2 Lumboischialgie Programm 3 + U3 Cervicobrachialgie Programm 4 + U4 Chronische Schmerzen Programm 5 + U5 Gate Control + Endorphinausschüttung Programm 6 + U6 Gonarthrose - Coxarthrose Programm 7 + U7 Epicondylitis Programm 8 + U8 Algodystrophie Programm 9 + U9 Gate Control Dynamic (Entgewöhnung) Programm 10 + U10 Klassische Gate Control 120 Hz Programm 11 + U11 Krampfbehandlung Programm 12 + U12 Atrophie obere Extremitäten Programm 13 + U13 Atrophie untere Extremitäten Programm 14 + U14 Kräftigung obere Extremitäten Programm 15 + U15 Kräftigung untere Extremitäten Programm 16 + U16 Venöser Rückfluss Programm 17 + U17 URO - Dranginkontinenz Programm 18 + U18 URO - Mischinkontinenz Programm 19 + U19 URO - Stressinkontinenz Programm 20 + U20 Entspannung (dynamische Stimulation) Programm 21 + U21 Kombination aus aktiver Mobilisation des Handgelenks und Schmerzbehandlung Programm 22 + U22 Kombination aus aktiver Mobilisation des Ellbogens und Schmerzbehandlung Programm 23 + U2 Kombination aus aktiver Mobilisation des Kniegelenkes und Schmerzbehandlung Programm 24 + U24 Kombination aus aktiver Mobilisation des Fußgelenkes und Schmerzbehandlung Programm 25 + U25 Hemiparese Schulterschmerz DEUTSCHLAND schwa-medico Medizinische Apparate Vertriebsgesellschaft mbH Wetzlarer Str. 41 - 43 I 35630 Ehringshausen Tel. 06443 8333-110 I Fax 06443 8333-119 E-Mail: [email protected] I schwa-medico.de I shop.schwa-medico.de ÖSTERREICH schwa-medico Handelsgesellschaft m.b.H. Industriezeile 25 I 5280 Braunau Tel. 07722 66122 I Fax 07722 66123 E-Mail: [email protected] I schwa-medico.at Tel. +49 6443 8333113 I E-Mail: [email protected] schwa-medico.com Wuxi Jiaijian Medical Instruments Co., Ltd, Qinghong Rd. Wuxi City, China 0434 Stand: 2013-06-14 Export