Download Service Manual - Manuales de Service

DVP3111 DVP3300(X)
DVP3111X/77
DVP3111/55
DVP3300/93
DVP3300/96
Service Manual
TABLE OF CONTENTS
Page
. Technical Specifications…………....………………………..............1-2
. Safety Instruction, Warning & Notes….……………………....….....1-3
. DFU Instruction..............................................................................2-1
. Mechanical and Dismantling Instructions…………........................3-1
. Software Version & Upgrades, Region Code Cha nge..……..........4-1
. Trouble Shooting Chart…………………..……………………………
. 5-1
. Wiring Diagram………………………………………..………..….….6-1
. Electrical Diagrams and Print-layouts..….…………………....….…7-1
. Packing, Set Mechanical Exploded view & Part list.………..….….8-1
. Revision List..................................................................................9-1
©Copyright 2009 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in aretrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise
without the prior permission of Philips.
Published by FK-0940 BU AVM Printed in The Netherlands Subject to modification
Version 1.1
CLASS 1
LASER PRODUCT
GB
3141 785 34461
PHILIPS
1-2
Specifications for DVP3111/55
Note
• Specification and design are subject to change
without notice
Accessories supplied
• Remote control and batteries
• Audio/Video cables
• Power plug adaptor
• User Manual
Play media
• DVD-Video, Video CD/SVCD, Audio CD,
CD-R/CD-RW, DVD+R/+RW, DVD-R/RW, DivX-CD, Picture CD, MP3-CD
TV standard
• Number of lines:
• 625 (PAL/50Hz); 525 (NTSC/60Hz)
• Play: Multi-standard (PAL/NTSC)
Video performance
• Video DAC: 12 bits, 108 MHz
• Video output: 1 Vpp ~ 75 ohm
Video format
• Digital compression:
• DVD/SVCD/VCD/DivX
• Horizontal resolution:
• DVD: 720 pixels (50 Hz); 720 pixels
(60 Hz)
• VCD: 352 pixels (50 Hz); 352 pixels
(60 Hz)
• Vertical resolution:
• DVD: 576 pixels (50 Hz); 480 pixels
(60 Hz)
• VCD: 288 lines (50 Hz); 240 lines
(60 Hz)
Audio performance
• DA converter: 24 bits, 192 kHz
• Frequency response:
• DVD: 4 Hz - 22 kHz (48 kHz); 4 Hz 44 kHz (96 kHz)
• SVCD: 4 Hz - 20 kHz (44.1 kHz); 4
Hz - 22 kHz (48 kHz)
• CD/VCD: 4 Hz - 20 kHz (44.1 kHz)
• Signal-Noise (1 kHz): > 90 dB
(A-weighted)
• Dynamic range (1 kHz): > 80 dB
(A-weighted)
• Crosstalk (1 kHz): > 90 dB
• Distortion/noise (1 kHz): > 65 dB
• MP3: MPEG L3
Audio format
• Digital:
• MPEG/AC-3: Compressed digital (16,
20, 24 bits, fs 44.1, 48, 96 kHz)
• MP3: 96, 112, 128, 256 kbps &
variable bit rate, fs 32, 44.1, 48 kHz
• Analog sound stereo
• Dolby surround compatible downmix
from Dolby Digital multi-channel sound
Connections
• Video output: Cinch (yellow)
• Audio output (L+R): Cinch (white/red)
• Digital output:
• 1 coaxial: IEC60958 for CDDA/
LPCM; IEC61937 for MPEG 1/2,
Dolby Digital
Main unit
• Dimensions (w x h x d): 360 x 37 x 209
(mm)
• Net Weight: approximately 1.3 kg
Power
• Power supply rating: 110 - 240V, 50/60HZ
• Power consumption: <10 W
• Power consumption in standby mode:
<1 W
Laser specification
• Type: Semiconductor laser InGaAIP
(DVD), AIGaAs (CD)
• Wave length: 658 nm (DVD), 790 nm
(CD)
• Output Power: 7.0 mW (DVD), 10.0 mW
(VCD/CD)
• Beam divergence: 60 degrees
1-2
Specifications for DVP3300(X)/93/96
Note
• Specification and design are subject to change
without notice
Accessories supplied
• Remote control and batteries
• Audio/Video cables
• User Manual
Play media
• DVD-Video, Video CD/SVCD, Audio CD,
CD-R/CD-RW, DVD+R/+RW, DVDR/-RW, DivX-CD, Picture CD, MP3-CD,
USB flash drive
TV standard
• Number of lines:
• 625 (PAL/50Hz); 525 (NTSC/60Hz)
• Play: Multi-standard (PAL/NTSC)
Video performance
• Video DAC: 12 bits, 108 MHz
• Video output: 1 Vpp ~ 75 ohm
Video format
• Digital compression:
• DVD/SVCD/VCD/DivX
• Horizontal resolution:
• DVD: 720 pixels (50 Hz); 720 pixels
(60 Hz)
• VCD: 352 pixels (50 Hz); 352 pixels
(60 Hz)
• Vertical resolution:
• DVD: 576 pixels (50 Hz); 480 pixels
(60 Hz)
• VCD: 288 lines (50 Hz); 240 lines
(60 Hz)
Audio performance
• DA converter: 24 bits, 192 kHz
• Frequency response:
• DVD: 4 Hz - 22 kHz (48 kHz); 4 Hz 44 kHz (96 kHz)
• SVCD: 4 Hz - 20 kHz (44.1 kHz); 4
Hz - 22 kHz (48 kHz)
• CD/VCD: 4 Hz - 20 kHz (44.1 kHz)
• Signal-Noise (1 kHz): > 90 dB
(A-weighted)
• Dynamic range (1 kHz): > 80 dB
(A-weighted)
• Crosstalk (1 kHz): > 90 dB
• Distortion/noise (1 kHz): > 65 dB
• MP3: MPEG L3
Audio format
• Digital:
• MPEG/AC-3: Compressed digital (16,
20, 24 bits, fs 44.1, 48, 96 kHz)
• MP3: 96, 112, 128, 256 kbps &
variable bit rate, fs 32, 44.1, 48 kHz
• Analog sound stereo
• Dolby surround compatible downmix
from Dolby Digital multi-channel sound
Connections
• Video output: Cinch (yellow)
• Audio output (L+R): Cinch (white/red)
• Digital output:
• 1 coaxial: IEC60958 for CDDA/
LPCM; IEC61937 for MPEG 1/2,
Dolby Digital
Main unit
• Dimensions (w x h x d): 360 x 37 x 209
(mm)
• Net Weight: approximately 1.3 kg
Power
• Power supply rating: 110 - 240V, 50/60HZ
• Power consumption: <10 W
• Power consumption in standby mode:
<1 W
Laser specification
• Type: Semiconductor laser InGaAIP
(DVD), AIGaAs (CD)
• Wave length: 658 nm (DVD), 790 nm
(CD)
• Output Power: 7.0 mW (DVD), 10.0 mW
(VCD/CD)
• Beam divergence: 60 degrees
1-3
Safety instruction, Warning & Notes
Safety instruction
1. General safety
2.Laser safety
Safety regulations require that during a repair:
. Connect the unit to the mains via an isolation transformer.
. Replace safety components indicated by the symbol
,
only by components identical to the original ones. Any
other component substitution (other than original type)
may increase risk of fire or electrical shock hazard.
Safety regulations require that after a repair, you must
return the unit in its original condition. Pay, in particular,
attention to the following points:
. Route the wires/cables correctly, and fix them with the
mounted cable clamps.
. Check the insulation of the mains lead for external
damage.
. Check the electrical DC resistance between the mains
plug and the secondary side:
1) Unplug the mains cord, and connect a wire between
the two pins of the mains plug.
2) Set the mains switch the “on” position (keep the
mains cord unplug).
3) Measure the resistance value between the mains
plug and the front panel, controls, and chassis
bottom.
4)
Repair
or
correct
unit
when
¡
measurement is less than 1M .
the
resistance
5) Verify this, before you return the unit to the
customer/user (ref. UL-standard no. 1492).
6) Switch the unit “off”, and remove the wire between
the two pins of the mains plug.
This unit employs a laser. Only qualified service personnel
may remove the cover, or attempt to service this device
(due to possible eye injury).
Laser device unit
Type
: Semiconductor laser GaAlAs
Wavelength
: 650nm (DVD)
: 780nm (VCD/CD)
Output power
: 7mW (DVD)
: 10mW (DVD /CD)
Beam divergence: 60 degree
Note: Use of controls or adjustments or performance of
procedure other than those specified herein, may result in
hazardous radiation exposure. Avoid direct exposure to
beam.
1-4
Warning
1.General
2. Laser
. All ICs and many other semiconductors are susceptible to
. The use of optical instruments with this product, will
electrostatic discharges (ESD). Careless handing during
increase eye hazard.
repair can reduce life drastically. Make sure that, during
. Only qualified service personnel may remove the cover
repair, you are at the same potential as the mass of the
or attempt to service this device, due to possible eye
set by a wristband with resistance. Keep components and
injury.
tools at this same potential. Available ESD protection
with a disc loaded inside the player.
equipment:
1)
. Repair handing should take place as much as possible
Complete kit ESD3 (small tablemat, wristband,
connection box, extension cable and earth cable)
. Text below is placed inside the unit, on the laser cover
shield:
4822 310 10671.
2)
Wristband tester 4822 344 13999.
. Be careful during measurements in the live voltage
section. The primary side of the power supply , including
the heat sink, carries live mains voltage when you
CAUTION: VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN, AVOID EXPOSURE
TO BEAM.
connect the player to the mains (even when the player is
“off”!). It is possible to touch copper tracks and/or
components in this unshielded primary area, when you
Notes:
service
Laboratories. The double-D symbol is trademarks of Dolby
the
player.
Service
personnel
must
take
precautions to prevent touching this area or components
in this area. A “lighting stroke” and a stripe-marked
printing on the printed wiring board, indicate the primary
side of the power supply.
. Never replace modules, or components, while the unit is
“on”.
Manufactured
under
licence
Laboratories, Inc. All rights reserved.
from
Dolby
1-5
Notes
Lead-Free requirement for service
INDENTIFICATION:
x
Regardless of special logo (not always indicated)
Use only original spare-parts listed in the
Service-Manuals. Not listed standard-material
(commodities) has to be purchased at external
One must treat all sets from 1.1.2005 onwards, according
next rules.
companies.
x
Important note: In fact also products a little older can also
be treated in this way as long as you avoid mixing
solder-alloys (leaded/ lead-free). So best to always use
SAC305 and the higher temperatures belong to this.
Special information for BGA-ICs:
- always use the 12nc-recognizable soldering
temperature profile of the specific BGA (for
de-soldering
always
use
highest
lead-free
temperature profile, in case of doubt)
Due to lead-free technology some rules have to be
respected by the workshop during a repair:
- lead free BGA-ICs will be delivered in so-called
‘dry-packaging’ (sealed pack including a silica gel
x Use only lead-free solder alloy Philips SAC305 with
order code 0622 149 00106. If lead-free solder-paste is
pack) to protect the IC against moisture. After
required, please contact the manufacturer of your
opening, dependent of MSL-level seen on
solder-equipment. In general use of solder-paste within
indicator-label in the bag, the BGA-IC possibly
workshops should be avoided because paste is not easy
still
to store and to handle.
communicated via AYS-website.
to
be
baked
dry.
This
will
be
Do not re-use BGAs at all.
x Use only adequate solder tools applicable for lead-free
solder alloy. The solder tool must be able
has
x
For sets produced before 1.1.2005, containing
o To reach at least a solder-temperature of 400°C,
leaded soldering-tin and components, all needed
o To stabilize the adjusted temperature at the
spare-parts will be available till the end of the
solder-tip
o To exchange solder-tips for different applications.
x Adjust your solder tool so that a temperature around
360°C – 380°C is reached and stabilized at the solder
joint. Heating-time of the solder-joint should not exceed
service-period. For repair of such sets nothing
changes.
x On our website:
www.atyourservice.ce.Philips.com
You find more information to:
~ 4 sec. Avoid temperatures above 400°C otherwise
BGA-de-/soldering (+ baking instructions)
wear-out of tips will rise drastically and flux-fluid will be
Heating-profiles of BGAs and other ICs used in
destroyed. To avoid wear-out of tips switch off un-used
Philips-sets
equipment, or reduce heat.
x Mix of lead-free solder alloy / parts with leaded solder
alloy / parts is possible but PHILIPS recommends
You will find this and more technical information
within the “magazine”, chapter “workshop news”.
strongly to avoid mixed
For additional questions please contact your local
solder alloy types (leaded and lead-free). If one cannot
repair-helpdesk.
avoid, clean carefully the
solder-joint from old solder alloy and re-solder with new
solder alloy (SAC305).
2-1
DVP3300/93 QSG:
4
The following excerpt of the Quick Start Guide serves as an introduction to the set.
The complete Direction For Use can be download in different languages from
Philips Customer Contact & Support site: www.p4c.philips.com
www.philips.com/welcome
Warning
2009 © Koninklijke Philips N.V.
All rights reserved.
DVP3300
Register your product and get support at
࣢‫ۥ‬
‡ Riskofoverheating!NeverinstalltheDVDplayerinaconÀnedspace.Always
‡ ࿎࿱޸അĞಯཡࣞDVDᅌ‫ࡱי‬ПቯᅿۡҠৄࢹடdඵሶᅿDVDᅌ‫ࡱי‬ሽ༘ટ
leaveaspaceofatleastfourinchesaroundtheDVDplayerforventilation.Ensure
thecurtainsorotherobjectsnevercovertheventilationslotsontheDVDplayer.
‡ NeverplacetheDVDplayer,remotecontrolorbatteriesnearnakedÁamesor
otherheatsources,includingdirectsunlight.
‡ OnlyusethisDVDplayerindoors.KeepthisDVDplayerawayfromwater,
moistureandliquid-Àlledobjects.
‡ NeverplacethisDVDplayeronotherelectricalequipment.
‡ KeepawayfromthisDVDplayerduringlightningstorms.
‡ Wherethemainsplugoranappliancecouplerisusedasthedisconnectdevice,
thedisconnectdeviceshallremainreadilyoperable.
‡ Visibleandinvisiblelaserradiationwhenopen.Avoidexposuretobeam.
սሢ൴ჩ‫׌‬؇ৄࢹႽҮົ‫ۦ‬d೴Ѯ֕ੜࡩ౥๓འບӤࡘᇝ‫׵‬DVDᅌ‫ࡱי‬൪
؇ົ‫ۦ‬Ԅd
‡ ಯཡࣞDVDᅌ‫ࡱי‬cႌে౸ࡩ‫ت‬՟‫ۄ‬ᅿ୞ࡧࡩ౥๓അᅙĥѩ৵ሒൿ؇ၿ‫ޝ‬Ħ‫ܚ‬
यd
‡ ऩᅿ෋ட඲ᄊְDVDᅌ‫ࡱי‬dഀְDVDᅌ‫ࡱי‬ᅛਸฅcඣ౹ߦඛᄗႣບ؇འ
ບd
‡ ಯཡְࣞDVDᅌ‫ۄࡱי‬ᅿ౥๓‫ت‬ኒඃ҃൪୍d
‡ ਤ‫ت‬ມ౹౛ࢹĩೊᅛਸְDVDᅌ‫ࡱי‬d
‡ ࣞ‫ت‬ᅙԎ໊ࡩඃ҃᰹ߨ౸ᄊ኶ٰ‫ت‬ඃ҃ඪĩ‫تٰܠ‬ඃ҃ჭসႽ฽ඪ඲ᄊd
‡ ‫ܠ‬ඃ҃‫ח‬ঙඪĩ‫׋‬ᅿস࣐ࢅӤস࣐؇ࡹ‫ޝ‬۷ൿdҧ୉ሒ෌ࡹ‫ޝ‬෱d
EN
ZH_CN
Print your user manual at www.philips.com/support
ဵչႊႬ߀൱ҬĶ౬٤ໝZZZSKLOLSVFRPVXSSRUW
2-2
1
3
AUDIO OUT L/R &
VIDEO OUT
2
DIGITAL IN
DIGITAL OUT/
COAXIAL
យᝆ
ࡉࣞ௠ᇛយᝆ
English
ߍࣞ zˊஔ
ᜰᮓ
DivXߍࣞ
᭶ᮓ
᭶ᮓ
џጒ
И̨
DVD ᖐӠ
:
:ᔡஔ
ᔡஔ
2-3
DVP3111/55:
Product overview
Main unit
a
b
c de f
a
•
Turn on the unit or switch to
standby.
b Disc compartment
c Indicators
d IR sensor
• Remote sensor.
e
•
Open or close the disc
compartment.
•
Start, pause or resume disc play.
f
2-4
Remote control
g
/
•
u
a
b
•
(Previous/Next)
Skip to the previous or next title,
chapter, or track.
Press and hold for fast-backward or
fast-forward search.
c
h ANGLE
• Select a viewing angle of a DVD.
• Switch veiwing modes during playing
JPEG slideshow.
t
d
i ZOOM
• Zoom into or out of an image.
s
e
j
•
f
g
r
q
p
h
i
MUTE
o
j
n
k
m
l
MUTE
Mute or restore audio output.
k STEP
• Play video frame by frame.
l SLOW
• Select a slow forward.
m REPEAT A-B
• Repeat a specific section within a
track/disc.
n REPEAT
• Select or turn off repeat mode.
o STOP
• Stop play.
p PLAY/PAUSE
• Start, pause or resume disc play
q SUBTITLE
• Select a subtitle language for video.
r AUDIO
• Select an audio language or channel.
a
•
Turn on the DVD player or switch to
standby mode.
b DISPLAY
• Display the current play status or
disc information
c Numeric Keypad 0 - 9
• Select an item to play.
d SEARCH
• Start playback from designated point.
e SETUP
• Access or exit the setup menu.
f
•
•
•
(Navigation buttons)
Navigate through the menus.
Search fast-forward (right) or fastbackward (left).
Search slow-forward (up) or slowbackward (down).
OK
• Confirm an entry or selection.
s DISC MENU
• Access or exit the disc menu.
• For VCD 2.0 and SVCD, turn on or
off the PBC (playback control) mode.
t RETURN/TITLE
• Returns to the previous menu.
• For DVD, navigates to title menu.
• For VCD version 2.0 or SVCD with
PBC turned on, returns to the menu.
u
OPEN/CLOSE
• Open or close the disc
compartment.
2-3
DVP3300/93:
Product overview
Overview of the remote control
Overview of the main unit
u
a
b
a
•
a
b
c
c defg
(Standby-On)
Turn on the DVD player or switch to
standby mode.
b Disc compartment
t
d
s
e
c Indicators
d
•
e
(Open/Close)
Open or close the disc
compartment.
•
(Play/Pause)
Start, pause or resume disc play.
•
(USB jack)
Connect a USB flash drive.
f
f
g
r
h
i
q
p
o
j
n
k
m
l
Remote control
a
•
Turn on the DVD player or switch to
standby mode.
•
Display the current play status or
disc information.
b
2-4
c Numeric Keypad 0 - 9
• Select an item to play.
q
d
r
•
Start playback from designated point.
e
•
Select a subtitle language for video.
•
Select an audio language or channel.
•
•
/
Access or exit the disc menu.
For VCD 2.0 and SVCD, turn on or
off the PBC (playback control) mode.
•
•
•
/
Returns to the previous menu.
For DVD, navigates to title menu.
For VCD version 2.0 or SVCD with
PBC turned on, returns to the menu.
s
•
Access or exit the setup menu.
f
(Navigation buttons)
Navigate through the menus.
Search fast-forward (right) or fastbackward (left).
Search slow-forward (up) or slowbackward (down).
OK
Confirm an entry or selection.
•
•
•
•
•
g
/
•
•
(Previous/Next)
Skip to the previous or next title,
chapter, or track.
Press and hold for fast-backward or
fast-forward search.
h
•
•
Select a viewing angle of a DVD.
Switch veiwing modes during playing
JPEG slideshow.
•
Zoom into or out of an image.
•
Select USB device source.
•
Play video frame by frame.
•
Select a slow forward.
•
A-B
Repeat a specific section within a
track/disc.
•
Select or turn off repeat mode.
•
Stop play.
•
Start, pause or resume disc play
i
j
k
l
m
n
o
p
t
u
•
Open or close the disc
compartment.
2-3
DVP3300X/96
Overview of the remote control
Product overview
Overview of the main unit
u
a
b
a
•
a
b
c
c defg
(Standby-On)
Turn on the DVD player or switch to
standby mode.
t
d
s
e
b Disc compartment
c Indicators
d iR sensor
•
Remote sensor.
e
•
f
(Open/Close)
Open or close the disc compartment.
•
(Play/Pause)
Start, pause or resume disc play.
•
(USB jack)
Connect a USB ash drive.
g
f
g
r
q
p
h
i
USB
o
j
n
k
m
l
a
•
Turn on the DVD player or switch to
standby mode.
b DISPLAY
•
Display the current play status or disc
information
c Numeric Keypad 0 - 9
•
Select an item to play.
d SEARCH
•
Start playback from designated point.
2-4
e SETUP
•
Access or exit the setup menu.
f
(Navigation buttons)
Navigate through the menus.
Search fast-forward (right) or fastbackward (left).
Search slow-forward (up) or slowbackward (down).
•
•
•
OK
•
Conrm an entry or selection.
g
/
•
•
(Previous/Next)
Skip to the previous or next title, chapter,
or track.
Press and hold for fast-backward or fastforward search.
h ANGLE
•
Select a viewing angle of a DVD.
•
Switch veiwing modes during playing
JPEG slideshow.
i ZOOM
•
Zoom into or out of an image.
j USB
•
Select USB device source.
k STEP
•
Play video frame by frame.
l SLOW
•
Select a slow forward.
m REPEAT A-B
•
Repeat a specic section within a track/disc.
n REPEAT
•
Select or turn off repeat mode.
o STOP
•
Stop play.
p PLAY/PAUSE
•
Start, pause or resume disc play
q SUBTITLE
•
Select a subtitle language for video.
r AUDIO
•
Select an audio language or channel.
s DISC MENU
•
Access or exit the disc menu.
•
For VCD 2.0 and SVCD, turn on or off
the PBC (playback control) mode.
t RETURN/TITLE
•
Returns to the previous menu.
•
For DVD, navigates to title menu.
•
For VCD version 2.0 or SVCD with PBC
turned on, returns to the menu.
u
•
OPEN/CLOSE
Open or close the disc compartment.
3-1
Mechanical and Dismantling Instructions
Dismantling Instruction
Detailed information please refer to the model set.
The following guidelines show how to dismantle the player.
Step1: Remove 5 screws around the Top Cover, and then remove the Top Cover (Figure 1).
Figure 1
Step2: If it is necessary to dismantle Loader or Front Panel, the Front door should be removed first. (Figure 2)
Note: Make sure to operate gently otherwise the guider would be damaged.
Please kindly note that dismantle
the front door
assembly carefully to avoid damage tray and the front door.
Figure 2
3-2
Mechanical and Dismantling Instructions
Detailed information please refer to the model set.
Dismantling Instruction
Step3: If the tray can’t open in normal way, you can make it through the instruction as below (Figure 3).
Note: Make sure to operate gently otherwise the guider would be damaged.
Figure 3
Step4: Dismantling Front Panel, disconnect the connectors (XP3), need release 4 snaps of Front Panel
and 2 snaps of bottom cabinet , then gently pull the Panel out from the set. (Figure 4 - Figure 6)
XP7 24Pin
XP2
XP8
XP9
Figure 4
XP3
3-3
Mechanical and Dismantling Instructions
Detailed information please refer to the model set.
Dismantling Instruction
Figure 5
Step5: Dismantling Loader, disconnect the 3 connectors (XP7, XP8, XP9 ) aiming in the below figure, and remove 1 screw that
connects the loader and the bottom cabinet. (Figure 5 & 6)
Figure 6
3-4
Mechanical and Dismantling Instructions
Dismantling Instruction
Detailed information please refer to the model set.
Step6: Dismantling Main Board, first disconnect the connector (XP2), and then remove 3 screws. (Figure 7)
Step7: Remove the 4 screws on Power Board to dismantle the Power Board. (Figure 7)
Figure 7
4-1
Software upgrade
B. Read out the Firmware version to confirm the
How to upgrade the software
1)
A.
upgrading
Burn the data onto a blank CD-R or RW disc.
Procedure for software upgrade:
1) Power on the set and insert the prepared Upgrade
1)
Power on the set and Open the tray door.
2)
Press <9><6><6>button to check the software
information.
The software version and other information are
displayed on the TV screen as follows:
CDR.
2) The set will starts reading disc & response with
the following display TV screen:
FE Version: XXXX.XXXXXX
DSP Version: DSP.XX
Loading
Firmware Upgrade Erase and program.
OK
BE Version: DVP33XX_XX.XX
Region Code: X
Cancel
Select OK to start upgrade.
3)
Press <OK> button to confirm, then screen will
display :
Firmware Upgrade Programming, Please Wait...
Do not Switch the Player Off !
4)
The upgraded disc will automatically out when
files coping complete, then take out the disc.
5)
About 1 minute later, the tray will automatically
close when upgrading complete.
Region Code Change
1) Power on the set and open the tray door;
2) Press "9" "8" "7" "9" and press the region
code number (0-6) on the remote control.
Notes:restart after above steps.
Caution: The set must not be power off during
upgrading, Otherwise the Main board will be
damaged entirely.
Trouble shooting chart
5-1
Spindle motor does not move
Motor no move
Go
Check the FFC connection
No
Correct connection
between 24P and the loader.
Yes
Check whether “RFA5V”
No
Check
(+5V) voltage is normal.
the
RFA5V
power
supply
Yes
Check whether laser voltage
No
(2.3V for DVD & 1.9V for CD)
Check/Replace Q4ǃQ5.
on Collector of Q4 and Q5
Yes
1.Whether voltage on pin 97 of U2
No
varies between 0 and 3.3V (3.3V for
Check/ Replace U2.
CD and 0V for DVD),
2.Whether peripheral components
are eroded or badly soldered.
Yes
1.
Have no
focus
No
Check U2 pin89 FOCUS_PWM
signals
2.If there are F+, F-, T+ and Tsignals output from U4.
Yes
FOCUS_PWN waveform
Check/Replace the loader
Trouble shooting chart
5-2
The power can not be on or off
The power can’t be
on or off
Go
Check the power supply
No
on the power board is
Repair the power board
normal.
Yes
Check if the CON2 on the
No
power board to XP2 on the
Yes
Check/Correct
connection
decoder board is in good
contact.
Yes
Check
if
the
xp1
on
the
decoderboard to XS301 on the
frontboard is in good contact
Yes
No
Correct the connection
5-3
All output voltages on the power board is 0V or deviated.
Trouble shooting chart
All output voltages on
the power board is 0V or
deviated
Yes
Check whether
Yes
Replace F1
F1 is blown
No
Check whether there is
No
Replace C1&C2 if D1, D2, D3, D4 are
normal.
300V on C1 or C2.
Yes
Check whether 100KHz
oscillating signal on
Pin6 of U1
No
Check/ replace U1.
U1(PIN 3 - RC waveform)
U1(PIN 8 - Drain waveform)
Yes
Check if +5V, +12V are
short.
Yes
Check whether the components in the
short-circuit voltage are defected or eroded.
No
Check whether U1 are eroded.
Trouble shooting chart
5-4
Disc cannot be read.
Disc cannot be read.
Yes
Check the FFC connection
No
Check the loaded circuit
between 24P and the loader.
Yes
1.Check voltage on pin 97 of U2 varies
between 0 and 3.3V:
Check whether there is laser
No
voltage (2.3V for DVD and 1.9V
Æ3.3V for CD
Æ0V for DVD
for CD) on Collector of Q4 &Q5
2.Check whether peripheral components
are eroded or defect
Yes
Check
U2,
U4,
and
No
Re-solder or replace the defective parts
peripheral components are
eroded or badly soldered.
Yes
Check if there is RFO signal on
pin10 of XP7. (The normal RFO
No
Check U1 and peripheral components
signal is a clear reticulated wave)
Yes
Check the connection
between U2
Yes
Replace U2 or loader.
No
Correct connection
Trouble shooting chart
5-5
Only DVD disc or only disc except DVD can be played
Only DVD disc, or only disc
except DVD can be Played.
Go
Check
the
FFC
connection between
24pin and the loader.
No
Check the loaded circuit
Yes
Check laser voltage (2.3V) output
Check the solder status on U2 and
No
on Collector of Q4 if pin87 of U2 is
peripheral components
at low level.
Yes
No
Check whether there
is voltage variance on
pin 88 of U2.
check if bad solder exist on U2 and
peripheral components
Yes
Check whether pins of U2 and
peripheral
components
No
are
Replace the bad spare parts
badly soldered, defected
Yes
Check Q4 whether
in good condition
Yes
Change U2 or the loader.
No
Correct connection
Trouble shooting chart
5-6
No display on LED, and buttons do not work
No display on LED, and
buttons do not work
Yes
Check whether there is
correct
contact
between XS301 and
XP1
No
Correct connection
Yes
Check VCC(+5v) voltage
No
on the power and front
board
Fix power supply board top
a power supply for should
electric circuit
Yes
Check there are CS, DATA
No
Check the U2’s pin 48,95,96 arrive
and CLK signals on XS301
on the front board.
the XP1 connect condition
XP1 (PIN 1 CLK)
XP1 (PIN3 DOUT)
Yes
1.Check whether bad solder exists on
Q302,Q303 and pins of LEDS,
2.Check whether the circuit connected to
K301,K302,is broken,
3.Check whether R303,R304,R302 are
open-circuit.
Yes
Replace Q302,Q303 or LEDS
No
Correct connection
5-7
Distorted audio and loud noise
Distorted audio and
loud noise
Yes
Check the power supply voltages
No
+12VA
Check whether the output of
the power board is normal.If
abnormal ,change the power
board
Yes
Check whether R73
and R77 are normal
No
Replace R77 and R73
Yes
Check
whether
muting
the
No
Replace Q8,Q10 ,Q12
transistor
Q8,Q10.Q12 are normal
Yes
Checking the U5 leads the
No
&RUUHFWFRQQHFWLRQ
feet has no to break to
open
Yes
No
Check whether the U7 or
U8 powersupply normal
Yes
Replace U7 or U8
Check U7,U8
Trouble shooting chart
Trouble shooting chart
5-8
Abnormal color of video picture
Abnormal color of
video picture
Yes
Check
whether
the
No
Check Y2, R30, C31 and C33
27MHz output signal
Yes
Check whether the 3.3V
and 1.8V power supply
voltages on the decoder
board are normal.
No
Check other of power supply electric
circuit
Yes
Check whether the
video filter network
circuit is normal.
No
Correct the connection
Yes
Check if the video signals on Pin
58,60,61,63 of U1 are normal
No
Change U2
Trouble shooting chart
5-9
Remote reception is insensitive or fails.
Remote reception is
insensitive or fails.
Go
Check if the remote
control works properly.
No
Check battery
Yes
Check if the power supply
No
Check
voltage to the remote censor
L2
is normal
Yes
Use an oscilloscope to check if there is
No
output waveform from the first pin IR of the
IR600 (PIN1 - RC waveform)
remote censor after pressing button on the
remote control.
Yes
Yes
Check if there is IR
signal on pin 49 of U2
Change U2
IR waveform
No
Correct connection
Trouble shooting chart
5-10
No video picture, no sound.
No video picture,
no sound.
Check whether all the voltages
No
Check the loaded circuit
from the power board to the
CVBS(R1 point) waveform
decoder board are normal.
Yes
Check if the reset circuit consisting
No
of CE3, D6 and R21 is normal (at a
Change CE3, D6 and R21.
high level for tens of milliseconds,
then constantly at 3.3V).
27Mhz waveform
Yes
Crystal oscillator Y2 and
Check whether there is
No
peripheral components
27MHz signal output.
are defected or eroded.
Yes
No
Check if there is 135MHz
signal output on R31.
Check whether
short-circuit or bad
solder on U1,U3
SDRAM(R31 PCLK) waveform
No
Yes
Check if short-circuit and
bad solder exist on Pin
60
No
Check U2.
Yes
Reconnect the component in
Yes
6-1
6-1
A
B
C
D
E
DVP3111 (2CH) WIRING DIAGRAM
DVP3300(X) (2CH+USB) WIRING DIAGRAM
D
COAX
CVBS
D
R
L
P2
AUDIO
AMP&LPF
ASA W F88 + SANYO 8 8 DV38
VIDEO LPF&DRIVE
24
C
XP7
24PIN*0.5
LOAD+
LOADTROUT
GND
TRIN
B
6
1
1
XP1
9PIN*2.0
16M
SDRAM
GND
4
USB 5V
POWER-K
B
1
7
XS301
9PIN*2.0
1
XP601
USB AND O
4PIN*2.0
POWER+
1
DN
LED-
1
9
XS302
USB
DP
IR
5V
GND
DATA
CS
CLK
POWER_K
PLAY_PAUSE
OPEN/CLOSE
1
5
XP11 4PIN*2.0
4
6
MAIN BOARD
MP-1
LED+
CON2 (1-5PIN)
5PIN*2.5
16M
FLASH
XP9
5PIN*2.0
5
4
SWITCH
XP1
BOARD 4PIN*2.0
+5V
+5V
GND
+12V
GND
5
CD5888
1
1
1
1
POWER
SUPPLY
5PIN*2.5
SPSP+
LIMIT
GND
SLSL+
MOTER
DRIVER
ZR36966/XF2
6PIN*2.0
XP8
C
DOWN-LOAD
XP2 (1-5PIN)
DVD LOADER
XP5
FB BOARD
BOARD
A
A
A
B
C
D
E
7-1
7-1
A
B
C
D
E
Front Board Circuit Diagram:
VCC
)5200$,1%2$5'
R311
R312
R313 R314 R315
10K
10K
10K
XS301
IR
5V
GND
VSDA
VSTB
VSCK
9
8
7
6
5
4
3
2
1
1
10K
10K
1
LED_Standby
LED_PLAYER
LED_ON
POWER_K
PLAY_PAUSE
OPEN/CLOSE
C302
C301
0.1u
0.1u
VCC
9PIN/2.0mm
K302
K303
REM301
5
4
OPEN/CLOSE
PLAYER/PAUSE
5
4
VCC
GND
IR
R301
3
2
1
100 ohm
IR
+
REM
C303
0.1u
CE300
47uF
C308
100p
C309
100p
VCC
R305
R306
470
470
R310
1
2
3
4
100
ON orange
LED+
PLAY green
LED2
10MA
NC/0R
2
LED_ON
C305
1U/NC
5MA
NC/0R
10MA
RED
C316
100p
R316
R317
XS302
CON4(2.0)
LED3
standby
LED+
LEDGND
POWER_K
LEDD301
Q302
8550
LED_PLAYER
CE200
22uF/NC
Q303
8550
2
LED_Standby
1N4148
C306
C307
NC/0.1U
NC/0.1U
3
3
4
4
A
B
C
D
E
7-2
7-2
A
B
C
D
E
Switch Board Circuit Diagram:
K304
1
1
2
3
4
XP1
CON4(2.0)
POWER
1
LED4
C319
47p
SWITCH
C317
47p
C318
47p
BOARD
2
2
3
3
4
4
A
B
C
D
E
7-3
7-3
1
2
3
4
5
USB Board Circuit Diagram for DVP3300:
A
A
B
B
P800
USB
USB00
USB
1
2
3
4
5
6
MGND
MGND
VCC
USB_DN
USB_DP
SGND
VCC
SGND
USB_DN
USB_DP
1
2
3
4
1
2
3
4
XS800
4PIN/2.0mm
MGND
SGND
FB100
0
C
C
D
D
E
E
1
2
3
4
5
7-4
7-4
A
B
C
D
E
Power Board Circuit Diagram:
1
1
F1
T2AL/250ac
TR1
NTC 10&20
D1
1N4007
2
1
P3
D2
1N4007
+
2
1
+
+
C N1
680uH
RV1
10K471
AC INPUT
+ C1
D3
1N4007
1
1
AC INPUT
+
L1
CON1
AC INPUT
D4
1N4007
+ C2
10uF/400V(250V/450V)
P2
15uF/400V(250V/450V)
L6
⺕⦴
T1
EEL19
5
D5
FR102
R2
R3
1/4W120K 1/4W120K
4
+
C5
152/1KV
C3
10uF/50V
6
CON2
6
5
4
3
2
1
7
2
3
R4
D8
IN4007
D7
FR102
9
+
C6
47uF/25V
1/6W10k
-22V
GND
+12V
GND
+5V
+5V
2
6X2.5 HEADER
C9
104/50V
8
1
D10
SR360/SR340
12
C14
NU
L2
6.8uH
1
R1
NU
EN/UV
+
10
+
C7
1000uF/16V
C8
470uF/16V
R5
1/6W12K 1%
R10
1/6W100
S
R13
4
1/6W100k
1
S
7
S
6
S
U1
TNY176/177
5
11
1/6W22
8
3
2
BP/M
NC
Drain
4
R11
R8
1/6W1k
C11
0.1uF/63V
R9
1/6W10k
3
2
3
U2
PC123X92
1
R7
1/6W11.3k 1%
2
U3
TL431
3
3
CY1
102/400Vac
* CAUTION :
THE PARTS MARKED WITH
ARE IMPORTANT PARTS ON THE SAFETY.
PLEASE USE THE PARTS HAVING THE DESIGNATED PARTS NUMBER WITHOUT FAIL.
4
4
A
B
C
D
E
7-4
7-4
A
B
C
D
E
Power Board Electric Diagram for DVP3300X/96:
F1
T2AL/250ac
TR1
NTC 10&20
P3
D1
D2
1N4007 1N4007
1
1
1
L1
AC INPUT
CN1
CX1
RV1
10K471
0.1uF/275Vac
AC INPUT
R6 1/6W1K(NU)
+
D3
D4
1N4007 1N4007
1
1
+
+
2
680uH
C1
10uF/400V(250V/450V)
+ C2
15uF/400V(250V/450V)
P2
L6
⺕⦴
T1
EEL19
5
D5
FR102
R2
R3
1/4W120K 1/4W120K
4
+
C5
152/1KV
C3
10uF/50V
6
CON2
6
5
4
3
2
1
7
2
3
R4
D8
IN4007
D7
FR102
9
+
C6
1/6W10k
47uF/25V
-22V
GND
+12V
GND
+5V
+5V
2
6X2.5 HEADER
C9
104/50V
8
1
D10
SR360/SR340
12
R1
NU
C14
NU
L2
6.8uH
1
11
+
C7
1000uF/16V
C8
470uF/16V
R5
1/6W12K 1%
R10
1/6W100
R13
1
1/6W100k
4
3
+
10
1/6W22
EN/UV
S
S
7
S
6
5
S
U1
TNY176/177
8
2
BP/M
3
NC
Drain
4
R11
R8
1/6W1k
3
C11
0.1uF/63V
R9
1/6W10k
3
2
3
U2
PC123X92
1
R7
1/6W11.3k 1%
2
U3
TL431
CY1
102/400Vac
* CAUTION :
4
THE PARTS MARKED WITH
4
ARE IMPORTANT PARTS ON THE SAFETY.
PLEASE USE THE PARTS HAVING THE DESIGNATED PARTS NUMBER WITHOUT FAIL.
A
B
C
D
E
7-5
7-5
A
B
C
D
E
Main Board Circuit Diagram: POWER
R1
0R
DSPVCC33
CE1
1
OPEN/CLOSE
PLAY/PAUSE
POWER_K
CLK
LED_ON
CS
LED_PLAYER
LED_standby DAT
GND
LED_5V
IR
4.7K
R2
CVBS_C
L1
0R
+
CVBS_C
LED ON
STANDBY 0 ON 1
LED PLAYR
STANDBY 0 ON 1 PLAYING 䮾⚕ XP3
9PIN/2.0mm
C1
150pF
R4
33R
C2
100pF
RCA_CVBS_OUT
220uF/16V
1
R109
R110
R111
R90
R91
R86
1
2
3
4
5
6
7
8
9
470R
470R
470R
4.7K
4.7K
470R
11
111
11
5
VSCK
VSTB
VSDA
L2
R3
OPEN/CLOSE
PLAY_PASUE
POWER_K
VSCK
VSTB
VSDA
NC/500
33R
M5V
IR
Y_R_V
Y_R_V
L3
V_OUT
0R
C3
150pF
I a
C4
150pF
0 A
IR
CVBS_G_Y
CVBS_G_Y
L4
Y_OUT
0R
C11
150pF
C8
C7
C6
C5
C95
C96
C97
C10
100pF 100pF 100pF 0.1uF 0.1uF 0.1uF 0.1uF 100p
C_B_U
C_B_U
C12
150pF
L6
U_OUT
0R
C14
150pF
C15
150pF
U11
V_OUT
2
U_OUT
1
6
2
5
3
4
RCA_CVBS_OUT
P1
RCA/AUDIO OUT
M5V
PESD3V3L5UY
RFA5V
00 A
RFA5V
1
A
[NM]
Q3
+12V
8550D
R12
22K
DSPVCC33
R13
4.7K
3
RCA_CVBS_OUT
1
2
1
1
1
C88
0.1uF
R6
C18
47pF
D12
PESD5V0S(L)1BA
C17
0.1uF
2
R9
C16
0.1uF
D11
PESD5V0S(L)1BA
0 A
2
5PIN/2.5mm
D10
PESD5V0S(L)1BA
+P12V
D9
2
C13
10nF
PESD5V0S(L)1BA
1
2
3
4
5
M5V
1
I a
XP2
1
2
3
4
5
6
RCA_CVBS_OUT
Y_OUT
U_OUT
V_OUT
RCA
RCA151
TO POWER BOARD
I a
2
Y_OUT
RCA_CVBS_OUT
3
4.7K
R7
PCON
4.7K
Q2
BT3904
LED PCON
L STBY.
H
W
n .
4
4
A
B
C
D
E
7-6
7-6
A
B
C
D
RESET Circuit
Important power supply!
DSPVCC33I
INSW
DRVSB
IN_OUT_SW
CLOSE
OPEN
HOMESW
INSW
DRVSB
IN_OUT_SW
CLOSE
OPEN
HOMESW
R97
15k
Main Board Circuit Diagram: Vaddis_SDRAM_Flash
URST#
R98
3.3k
C19
10nF
2N3904
CE19
10uF/16v
CEL5-5
C89
1 0MA
L7
1uF
R19
0.1U
RFN
RFP
RF_B
RF_A
VFE_YIN
RF_F
SPDL_SENS+
RF_E
SPDL_SENSRF_D
RF_C
15.4K 1%
0.1uF
VC
VFE_YIN
RF_F
SPDL_SENS+
RF_E
SPDL_SENSRF_D
RF_C
MA
RF_B
RF_A
VDDAFE
R18
HYPER
R22
4.7K
ad
MUTE_CTL
MUTE_CTL
n
SFCS
SFDO
SFDI
d
SFCLK
SFCLK
R104
R85
POWER_K
OPEN/CLOSE
PCON
SFCLK_0
33R
PLAY_PASUE
POWER_K
OPEN/CLOSE
24R/NC
USB_DP
USB_DN
USB5V
R105
R106
C91
R107
C92
15K/NC
47P
15K/NC
47P
24R/NC
0.1U
D1
1
RAMADD4
RAMADD3
RAMADD5
RAMADD2
RAMADD6
RAMADD1
RAMADD7
C90
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
Gen_4/VID7
SFCS
GND
SFDO/RS_SF
SFDI/RS128_Bootsel2
VDDC
VDDP
SFCLK/RS128_Bootsel1
GPIO[5]
SD_D/IGPIO[7]
PWM5
SD_CMD/GPIO[6]
SD_CLK/IGPIO[7]
VDDP
DP
DN
RAMADD[4]
RAMADD[3]
RAMADD[5]
VDDIP
RAMADD[2]
RAMADD[6]
RAMADD[1]
RAMADD[7]
VDDC
GND
MBRX120
2USB5V
R23
392 Ohm 1%
RSET
DAC1
VDDDAC
DAC2
DAC3
VDDDAC
DAC4
GNDC
XIN
XO
VDDPLL
GNDPLL
RESET#
VDDC
VDDP
IGPIO[44]
GPIO[43]/DUPRD0/TDO/SSCTXD
GND
GPIO[32]/SPDIFO
VDDP
GPIO[29]/AMCLK/APWM0GPIO[28]/APWM1GPIO[26]/APWM2GPIO[25]/AOUT2/APWM3GPIO[24]/DUPRD1/ALRCLK/APWM4IGPIO[23]/DUPTD1/ABCLK/APWM5-
Vaddis-966XE/XF
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
Close to
Vaddis
C_B_U
Y_R_V
CVBS_C
Y_R_V
CVBS_C
VDDDAC
CVBS_G_Y
OSCIN
OSCOUT
VDDPLL
CVBS_G_Y
RESET#
OSCOUT
IR
DUPRD0/VSDA
R30
100
C31
S/PDIF_OUT
S/PDIF_OUT
VDDAPWM
GP-0
GP-1
APWM_LAPWM_R-
C32
0.1uF
Crystal
Y2
27.000MHz
R28
220K
GP-4
GP-5
OSCIN
C33
DSPVCC33
1
2
3
4
DRC000
N t
RAMDAT14
RAMDAT1
RAMDAT15
RAMDAT0
as
C35
0.1uF
nn
t
ns N 1
C39
0.1U
C40
0.1U
1 5.10
XP6
4PIN/2.0mm
1
2
3
4
GP-5
GP-4
1 5.
Close to pin 38
Hy
RAMADD9
RAMADD8
RAMADD7
RAMADD6
RAMADD5
RAMADD4
RAMDQM
PCLK
RAMCKE
RAMDAT8
RAMDAT10
RAMDAT9
RAMDAT12
RAMDAT11
RAMDAT14
RAMDAT13
RAMDAT15
RAMDAT14
RAMDAT15
RAMDAT12
RAMDAT13
RAMDAT10
RAMDAT11
.Vadd s SDRAM F as
ad
T
DUPTD1
DUPRD1
na
VSS
DQ15
VSSQ
DQ14
DQ13
VDDQ
DQ12
DQ11
VSSQ
DQ10
DQ9
VDDQ
DQ8
VSS
NC
DQMH
CLK
CKE
NC
A11
A9
A8
A7
A6
A5
A4
VSS
[64Mbit:K4S641632H-UC70]
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
4
SCHEMATIC1
DSPVCC33
n
NM
U10
16Mbit: K4S161622C-TC/L70
C44
0.1U
D
CE4
470uF/6.3V
VDD
DQ0
VDDQ
DQ1
DQ2
VSSQ
DQ3
DQ4
VDDQ
DQ5
DQ6
VSSQ
DQ7
VDD
DQML
WE#
CAS#
RAS#
CS#
BA0
BA1
A10
A0
A1
A2
A3
VDD
C43
0.1U
10R
4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
C42
0.1U
VDD
A3
A2
A1
A0
A10/AP
BA
CS
RAS
CAS
WE
LDQM
VDDQ
DQ7
DQ6
VSSQ
DQ5
DQ4
VDDQ
DQ3
DQ2
VSSQ
DQ1
DQ0
VDD
C41
0.1U
U3
DSPVCC33
VSS
A4
A5
A6
A7
A8
A9
NC
CKE
CLK
UDQM
NC
VDDQ
DQ8
DQ9
VSSQ
DQ10
DQ11
VDDQ
DQ12
DQ13
VSSQ
DQ14
DQ15
VSS
L10
500
SDRAM3V3
055
3
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
C38
0.1U
SDRAM3V3
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
C37
0.1U
RAMDAT8
RAMDAT9
DSPVCC18
RAMCKE
PCLK
RAMDQM
RAMADD4
RAMADD5
RAMADD6
RAMADD7
RAMADD8
RAMADD9
Close to
Vaddis
DSPVCC18
R32
A
t an t
DUPTD0
DUPRD0
DSPVCC33
+
RAMADD11
WARNING
RAMDAT13
RAMDAT2
RAMDAT8
RAMDAT7
RAMDAT9
RAMDAT6
RAMDAT10
RAMDAT5
RAMDAT11
RAMDAT4
RAMDAT12
RAMDAT3
IPCLK
RAMWERAMDQM
RAMRASRAMCASRAMCS1-
RAMADD11
RAMCS0RAMBA
RAMADD9
RAMADD0
RAMADD8
RAMADD10
PCLK
C34
5P
VDDAPWM
. 0V
33pF
XP5
4PIN/2.0mm
IPCLK
R31
56R
33pF
IR
VSDA
DUPTD0/VSCK
DUPRD0/VSDA
C36
0.1U
DSPVCC18
2
C_B_U
VDDDAC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
[FUSE(500MA)]
3
4.7
C29
0.1U
VDDAFE
R15
C25
LD_DVD
LD_CD
MD_DVD
MD_CD
RESOUT
VREF
VC
C27
0.1U
VDDPLL
75R 1%
75R 1%
75R 1%
75R 1%
U2A
DSPVCC33
XP11
F1
DSPVCC33
500
R24
R25
R26
R27
NC
PLAY_PASUE
M5V
1 5MA
L8
VDDDAC
C82
Down load
4PIN/2.0mm
RF
C9
HOLD
4
3
2
1
RF
C24
33pF
DSPVCC18
DSPVCC33I
4.7K
SFCLK
SFDO
SPI FLASH-SOP8
At
AT DF0 1A
2
1nF
1
C21
0.1U
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
4.7K
8
7
6
5
/CS
VDD
SO /HOLD
/WP
SCK
GND
SI
C23
C20
10nF
Gen_5/GPIO[0]
Gen_6
VDDP
Gen_7
Gen_8
Gen_9
Gen_11
Gen_12/VID0
VDDC
GPIO[52]/PWMCO[3]/HSYNC
GPIO[51]/PWMCO[2]/FIELD
GPIO[50]/PWMCO[1]/VCLKx2
VDDPWM
GPIO[49]/PWMCO[0]
DVD_LD
CD_LD
DVD_MD
CD_MD
VDDSAFE
GNDREF
RESOUT
VREF
VC
GND1AFE
VFE_YIN
F
K
E
J
D
C
VDDAFE
B
A
VDD1AFE
RFN
RFP
GNDDACBS2
R20
1
2
3
4
1nF
RAMADD[0]
RAMADD[8]
RAMADD[10]
VDDP
RAMADD[9]
RAMADD[11]/GPO[64]
RAMCS0#
RAMBA
RAMCS1#/GPO[65]
RAMRAS#
RAMCAS#
VDDP
RAMWE#
RAMDQM
GNDPCLK
PCLK
VDDPCLK
RAMDAT[8]
RAMDAT[7]
RAMDAT[9]
RAMDAT[6]
RAMDAT[10]
RAMDAT[5]
RAMDAT[11]
RAMDAT[4]
RAMDAT[12]
RAMDAT[3]
VDDIP
RAMDAT[13]
RAMDAT[2]
VDDC
RAMDAT[14]
RAMDAT[1]
RAMDAT[15]
RAMDAT[0]
VDDP
GNDAPWM
VDDAPWM
SFCS
SFDI
C22
DSPVCC33
500
C26
10nF
VDDAFE
DSPVCC33
U1
DSPVCC33
FOCUS_PWM
LD_DVD
LD_CD
MD_DVD
MD_CD
C28
1nF
VDDPWM
VSTB
CD_DVD
CLOSE
HOMESW
CD_DVD
VSCK
SLED_PWM
SPDL_PWM
TRACK_PWM
VSCK
SPDL_PWM
SLED_PWM
OPEN
DRVSB
CD_DVD_1
FPC_STB
DUPTD0/VSCK
VSTB
1K
0 A
VDDAFE
Close to Vaddis!
FOCUS_PWM
TRACK_PWM
I a
1K
DSPVCC33
Q14
1
R17
4.7
+ CE2
100U/16V
RESET#
Q13
+
R16
R14
R100 1k
R101 3.3k
2N3904
INSW
1MA
VDDPWM
D8
NC/1N4148
R99
22k
R102
4.7k
IN_OUT_SW
E
A
B
RAMBA
RAMCS0RAMADD10
RAMADD0
RAMADD1
RAMADD2
RAMADD3
RAMDQM
RAMWERAMCASRAMRASRAMCS1-
R33
10K
RAMCKE
RAMDAT7
RAMDAT5
RAMDAT6
RAMDAT3
RAMDAT4
C49
0.1U
RAMDAT1
RAMDAT2
C48
0.1U
RAMDAT0
C47
0.1U
RAMDAT1
RAMDAT0
C46
0.1U
RAMDAT3
RAMDAT2
C45
0.1U
RAMDAT5
RAMDAT4
C84
0.1U
RAMDAT7
RAMDAT6
C83
0.1U
RAMADD3
RAMADD2
RAMADD1
RAMADD0
RAMADD10
RAMBA
RAMCS0RAMRASRAMCASRAMWERAMDQM
DSPVCC33
DSPVCC33I
SDRAM3V3
C
D
E
7-7
7-7
A
B
CDLD
DVDLD
DSPVCC33
C50
NM
[470pF]
R34
4.7R
C51
NM
[470pF]
R36
220R
LD_DVD
DSPVCC33
1
OPU
Sony310
DL3
IAT510
TOP1100S
SEMCO-SP1
MITSM820W
HD8(DV23)
HOP1200W
HD65/HD62
502W
Arima681
+ CE5
220uF/16V
Q4
9012
OPU
R34:
R38:
HD65PS
3.3R
3.3R
Others
4.7R
4.7R
CN201 is used for Sanyo/Samsung/Sony OPUs
R38
4.7R
25
26
XP7
SMD0.5 TOP
C52
1nF
TOP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
C53
1nF
+ CE6
220uF/16V
Q5
9012
DVDLD
R42
220R
R43
LD_CD
E
R39
100R
0
100R
10R
0
91R
0
NM
0
91R
NM
OPU
HOP1200W
Arima681
Others
R202=300R, for HOP1200W only
BEMF
Current Type(Default)
R40
100R
0
100R
10R
0
91R
0
NM
0
91R
NM
R270
100R
100R
NM
R35
2K
SP_M-
SPDL_SENS-
SPDL_SENS-
D5
2
DSPVCC33
R37
1R 0603-R
3
MD_DVD
R39
100R
[NM]
R283
100R
100R
NM
VR_CD
1
1
MD_CD
R41
R40
100R
[NM]
BAT54C
2K
SP_MOT-
SPDL_SENS+
SPDL_SENS+
VR_DVD
0R [300R]
OPU_HFM
RFA5V
CDLD
VR_DVD
VR_CD
OPU5V
VC1
D
Main Board Circuit Diagram: FE_Regulator
Close to CN201
EMC
C
C54
1nF
+
CE7
100uF/16V
L11
R44
10uH
33R
RF_E
.1V
RFA5V
U4
VC
R45
3.3K
RF_F
RF_B
RF_A
RF
FOCUS_S
PDIC Control:
DVD=LOW
CD=HIGH
CD_DVD
TR_B1
REGO2
CD_DVD
RF_D
RF_C
TACTTACT+
FACT+
FACT-
SLED_S
REGO1
OPEN
VINFC
MUTE
28
2
TR_B1
BIAS
27
3
REGO2
VINTK
26
4
VINSL
TR_B2
25
5
REGO1
NC
24
6
FWD
VINLD
23
7
REV
GND
22
29
GND
GND
30
8
VCC1
VCTL
21
NC
20
DRVSB
Close to Vaddis!
VC2
TRACK_S
C55
100pF
TR_B2
R46
1K
FOCUS_S
TRACK_S
R47
R48
51K [27K]
51K [27K]
SPDL_S
SLED_S
R49
R50
22K [22K]
51K [33K]
SPDL_S
C59
C60
C61
C62
1nF
1nF
27nF
27nF
FOCUS_PWM
TRACK_PWM
SPDL_PWM
SLED_PWM
27
28
CLOSE
AM5888S(HSOP-28)
1
C56
0.1uF
C57
0.1uF
2
+ CE8
47uF/16V
M5V
CE9
100uF/16V
LOAD-
C58
0.1uF
LOAD+
6
5
4
3
2
1
VOTR-
2
M5V
10
VOTR+
VCC2
19
SL_MOT- 11
VOSL+
VOLD-
18
SP_M-
SL_MOT+
SL_MOTHOMESW
SL_MOT+12
VOSL-
VOLD+
17
SP_MOT+
FACT-
13
VOFC-
VOTK-
16
TACT-
SP_MOT+
SP_MOT-
FACT+
14
VOFC+
VOTK+
15
TACT+
XP8
6PIN/2.0mm
SLEDSLED+
HOMESW
GND
SP+
SP-
9
Close to motor driver.
DSPVCC33
R54
1K 1%
M5V
VC2
DSPVCC33
XP9
5PIN/2.0mm
R52
4.7K
HOMESW
IN_OUT_SW
INSW
C63
NM
[1nF]
R58
1K 1%
2.2 OHM 2W
C64
NM
[1nF]
C67
0.1uF
I a
00 A
ℷᐌ I
0 A
HOMESW
IN_OUT_SW
INSW
5.6 OHM 1W
I a
ℷᐌ
C65
NM
[1nF]
3
R53
00 A
50 A
DSPVCC18
e
1
2
3
4
5
I a
00 A
ℷᐌ 5 0 A
R51
LOADLOAD+
DSPVCC33
TR_B1
TR_B2
Q6
SS8550D
Q7
R56
SS8550D
C66
+
0.1uF
CE10
220uF/16v
20k/1%
3
b
c
LOADLOAD+
OUTSW
GND
INSW
R55
33K
R57
CE11
+
4.7K/1%
REGO1
REGO2
R59
220uF/16v
R60
GND
10k/1% GND
12k/1%
GND
GND
4
4
A
B
C
D
E
7-8
7-8
A
B
C
D
E
Main Board Circuit Diagram: Audio_Input_Output
M5V
Q8
9012
R64
4.7K
R61
82K
R63
4.7K
1
39K
APWM_L-
C68
75pF
4
C69
1.2nF
R68
R69
3.3K
10K
6
OP+
5
MUTE
Q10
C70
0.1uF
9012
CE14
OP
U5B
LM4558
7
CE13
10uF/16V
R65
470
MUTE
R66
10K
8
+6VA
LMAIN_OUT
+
R62
+
1
Q9
3904
R67
470
+
220U/16V
R70
82K
R72
4.7K
39K
APWM_R-
C71
75pF
MUTE_CTL
R77
4.7K
+6VA
Q12
2N3904
OP
2
OP+
3
U5A
LM4558
CE16
10uF/16V
R74
1
8
MUTE_CTL
4
C72
1.2nF
R78
22K
470
RMAIN_OUT
+
R71
+
R73
4.7K
+12VA
MUTE
R75
10K
C73
0.1uF
+6VA
Q11
3904
R76
470
+12VA
2
2
+6VA
VFE_YIN
R96
VFE_YIN
1k
C74
1uF
XP10
R81
0R
MIC
C77
C76
3300p
100p
0.1uF
+12V
+12VA
R80
100R
+12V
R82
+ CE17
1
2
3
C75
R79
100K
+
33K
CE18
47uF/16V
100U/16V
pitch=2.0mm*3
RCA_CVBS_OUT
RCA_CVBS_OUT
P2
RCA/AUDIO OUT
RCA_CVBS_OUT
COAX_SPDIF
R83
C78
100
0.1uF
RCA
RCA 0
1
2
3
4
5
6
LMAIN_OUT
RMAIN_OUT
C30
47pF
COAX_SPDIF
S/PDIF_OUT
R84
C80
100pF
100
C81
100pF
C79
100pF
3
3
4
4
A
B
C
D
AUDIO
E
7-9
Front Board and Switch Board Print-layout (Bottom side):
7-9
7-10
Power Board Print-layout (Bottom side):
7-10
USB Board Print-layout (Bottom side) for DVP3300:
7-10
Power Board Print-layout for DVP3300X/96 (Bottom side):
7-10
7-11
7-11
Main Board Print-layout (Top side):
7-12
7-12
Main Board Print-layout (Bottom side):
8-1
DVP3300/93 Packing View:
PAC2
PAC4
PAC1
PAC5
PAC6 PAC7
PAC8
PAC3
PAC11
PAC10
PAC9
PAC9. Display Box
PAC6. AV Cable
PAC7. Poly Bag PAC1. Accessory Bag
PAC11. Left Buffer PAC10. Right Buffer PAC8. Remote Control
PAC4. Ueser Manual PAC5. Battery PAC12. Service Hotline PAC13. Service Guarantee PAC14. World Wide Guarantee Card
8-2
Exploded view for DVP3111/55:
It's a general mechanical exploded view for DVP3111/55, pls refer to model set for detailed information.
ASSY1 includes components: 2.3.4.19.20.21
8-3
DVP3111/55 SERVICE PARTLIST
ELECTRICAL PARTLIST
No
12NC No.
MECHANICAL PARTLIST
Description
8
996510029487
ASSY-MAIN BD
15
996510022923
ASSY-PW BD
18
996510029497
ASSY-FB BD
5
996510029486
ASSY-SW BD
9
996510029491
LOADER
OPU
996510021449
SANYO LOADER (DV38)
Q'ty
1
1
1
1
1
1
12NC No.
Description
Q'ty
1
996510029493
FRONT DOOR
10
996510029494
TOP CABINET
12
996510001175
POWER CORD
14
996510029513
BACK PANEL
16
996510006463
PAD
7
996510027099
BOTTOM PLATE
1
1
1
1
4
1
AVCABLE
996510001106
VIDEO CABLE 1500mm
1
Assy1
996510029512
FRONT PANEL ASSY
1
Q'ty
CON2
996510021451
HS 3P TJC-3Y/SCN-3Y L=80MM
1
ASSY-MAIN BD COMPONENT PARTLIST
Description
No
No
12NC No.
D5
996510009668
BAT54C
1
DBOX
996510029489
DISPLAY BOX
1
D9
996510020926
IC PESD5V0S1BA
1
PSOCKET
996510020885
POWER SOCKET transition
1
Q10
996510009670
TRANSISTOR SMT 3CG9012M
1
RC
996510029498
REMOTE CONTROL
1
Q11
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
XP1
996510029492
4PIN CABLE
1
Q12
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
XP7
996510001168
24PIN HS
1
Q13
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
XP8
996510021448
6PIN HS
1
Q14
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
XP9
996510004063
CABLE PH-5Y/PH-5Y L=130MM
1
Q2
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
XS301
996510029488
CABLE 9PIN 140MM FH-JC20
1
Q3
996510009671
PNP TRANSISTOR
1
Q4
996510021453
SMD. TRANSISTOR MMBT8550CLT1
1
SCREWS LIST:
Q5
996510021453
SMD. TRANSISTOR MMBT8550CLT1
1
No
Q6
996510009671
PNP TRANSISTOR
1
6
—
S/T SCREW B 2.6 X 8 BF
4
Q7
996510009671
PNP TRANSISTOR
1
11
—
S/T SCREW B3 X 6 BF
9
Q8
996510009670
TRANSISTOR SMT 3CG9012M
1
13
—
S/T SCREW B 3 X 7 BF
4
Q9
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
U1
996510020916
16M SPI FLASH EON
1
U2
996510029496
ZR36966PQCG-XF2
1
U3
996510029495
16M BIT SDRAM ISC42S16100E-7TL
1
U4
996510011055
IC CD5888CB
1
U5
996510010924
Dual operational amplifier
1
Y2
996510009675
27MCL20PF
1
ASSY-PW BD COMPONENT PARTLIST
No
12NC No.
D1
996510011047
Description
DIODE IN4007
Q'ty
1
D10
996500027866
DIODE SR360 3A/60V
1
D2
996510011047
DIODE IN4007
1
D3
996510011047
DIODE IN4007
1
D4
996510011047
DIODE IN4007
1
D7
996500014043
DIODE FR102 (FAST RECOVERY)
1
D8
996510011047
DIODE IN4007
1
L1
996510009942
COIL WIDTH
1
L2
996500032509
COIL SL0811-6R8K2R4
1
T1
996510010954
TRANSFORMER CONV
1
U1
996510010953
IC TNY176PN
1
U2
996500027867
PHOTOCOUPLER PS2561L1-1-V(WF)
1
U3
996500014609
IC AM431LP
1
ASSY-FB BD COMPONENT PARTLIST
No
12NC No.
Description
Q'ty
LED2
996500034464
LED BT-102D-31
1
LED3
996500034464
LED BT-102D-31
1
REM301
996510020925
HM338-12 RECEIVER MOD H=12MM
1
12NC No.
Description
Q'ty
8-2
Exploded view for DVP3300/93 and DVP3300X/96:
It's a general mechanical exploded view for DVP3300/93 and DVP3300X/96, Pls refer to the
Model set for detailed information.
ASSY1 includes components: 2.3.4.20.21.22
8-3
DVP3300/93 SERVICE PARTLIST
ELECTRICAL PARTLIST
No
12NC No.
MECHANICAL PARTLIST
Description
8
996510029525
ASSY-MAIN BD
15
996510021465
ASSY-PW BD
18
996510029526
ASSY-USB BD
19
996510029497
ASSY-FB BD
5
996510029486
ASSY-SW BD
9
996510029491
LOADER
OPU
996510021449
SANYO LOADER (DV38)
Q'ty
1
1
1
1
1
1
1
12NC No.
Description
Q'ty
1
996510029529
FRONT DOOR
10
996510029528
TOP CABINET
12
996510021454
3C PLUG POWER CORD
14
996510029531
BACK PANEL
16
996510006463
PAD
7
996510027099
BOTTOM PLATE
1
1
1
1
4
1
ABAG
996510018311
ACCESSORY BAG
1
AVCABLE
996510001106
VIDEO CABLE 1500mm
1
Assy1
996510029527
FRONT PANEL ASSY
1
Q'ty
CON2
996510021451
HS 3P TJC-3Y/SCN-3Y L=80MM
1
ASSY-MAIN BD COMPONENT PARTLIST
Description
No
No
12NC No.
D1
996510022393
SMD. DIODE MBRX140
1
DBOX
996510029533
DISPLAY BOX COLOR
1
D5
996510009668
BAT54C
1
GRANTEE
996500033761
SERVICE GUARANTEE
1
D9
996510020926
IC PESD5V0S1BA
1
LBUFFER
996510020937
LEFT CARD
1
Q10
996510009670
TRANSISTOR SMT 3CG9012M
1
LEAFLET
996510029524
WARRANTY LEAFLET
1
Q11
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
PBAG
996510019879
POLY BAG
1
Q12
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
QSG
996510029532
QSG
1
Q13
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
RBUFFER
996510021008
RIGHT CARD
1
Q14
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
RC
996510029523
REMOTE CONTROL
1
Q2
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
SHOTLINE
996500042132
SERVICE HOT LINE
1
Q3
996510009671
PNP TRANSISTOR
1
WCARD
996510019880
Worldwideguarantcard
1
Q4
996510021453
SMD. TRANSISTOR MMBT8550CLT1
1
XP1
996510029492
4PIN CABLE
1
Q5
996510021453
SMD. TRANSISTOR MMBT8550CLT1
1
XP7
996510001168
24PIN HS
1
Q6
996510009671
PNP TRANSISTOR
1
XP8
996510021448
6PIN HS
1
Q7
996510009671
PNP TRANSISTOR
1
XP9
996510004063
CABLE PH-5Y/PH-5Y L=130MM
1
Q8
996510009670
TRANSISTOR SMT 3CG9012M
1
XS301
996510029488
CABLE 9PIN 140MM FH-JC20
1
Q9
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
XS800
996510022394
4PIN CABLE WITH SHIELD L=180MM
1
U1
996510020916
16M SPI FLASH EON
1
U2
996510029496
ZR36966PQCG-XF2
1
SCREWS LIST:
U3
996510029495
16M BIT SDRAM ISC42S16100E-7TL
1
No
U4
996510011055
IC CD5888CB
1
6
—
S/T SCREW B 2.6 X 8 BF
6
U5
996510010924
Dual operational amplifier
1
11
—
S/T SCREW B3 X 6 BF
9
Y2
996510009675
27MCL20PF
1
13
—
S/T SCREW B 3 X 7 BF
4
ASSY-PW BD COMPONENT PARTLIST
No
12NC No.
D1
996510011047
Description
DIODE IN4007
Q'ty
1
D2
996510011047
DIODE IN4007
1
D3
996510011047
DIODE IN4007
1
D4
996510011047
DIODE IN4007
1
D8
996510011047
DIODE IN4007
1
D10
996500027866
DIODE SR360 3A/60V
1
D7
996500014043
DIODE FR102 (FAST RECOVERY)
1
L1
996510009942
COIL WIDTH
1
L2
996500032509
COIL SL0811-6R8K2R4
1
T1
996510010954
TRANSFORMER CONV
1
U1
996510010953
IC TNY176PN
1
U2
996500027867
PHOTOCOUPLER PS2561L1-1-V(WF)
1
U3
996500014609
IC AM431LP
1
ASSY-FB BD COMPONENT PARTLIST
No
12NC No.
Description
Q'ty
LED2
996500034464
LED BT-102D-31
1
LED3
996500034464
LED BT-102D-31
1
REM301
996510020925
HM338-12 RECEIVER MOD H=12MM
1
12NC No.
Description
Q'ty
8-3
DVP3300/96 SERVICE PARTLIST
ELECTRICAL PARTLIST
No
12NC No.
MECHANICAL PARTLIST
Description
8
996510029525
ASSY-MAIN BD
15
996510021485
ASSY-PW BD
18
996510029526
ASSY-USB BD
19
996510029497
ASSY-FB BD
5
996510029486
ASSY-SW BD
9
996510029491
LOADER
OPU
996510021449
SANYO LOADER (DV38)
Q'ty
12NC No.
Description
Q'ty
1
996510029529
FRONT DOOR
10
996510029528
TOP CABINET
12
996510021478
POWER CORD
14
996510030194
BACK PANEL
16
996510006463
PAD
7
996510027099
BOTTOM PLATE
1
1
1
1
4
1
AVCBL
996510001106
VIDEO CABLE 1500mm
1
Assy1
996510029527
FRONT PANEL ASSY
1
CON2
996510010962
5PIN CBL TJC3-5Y/SCN-5P L=90MM
1
Q'ty
RC
996510030187
REMOTE CONTROL
1
1
1
1
1
1
1
1
ASSY-MAIN BD COMPONENT PARTLIST
Description
No
No
12NC No.
D1
996510022393
SMD. DIODE MBRX140
1
XP1
996510029492
4PIN CABLE
1
D5
996510009668
BAT54C
1
XP7
996510001168
24PIN HS
1
D9
996510020926
IC PESD5V0S1BA
1
XP8
996510021448
6PIN HS
1
Q10
996510009670
TRANSISTOR SMT 3CG9012M
1
XP9
996510004063
CABLE PH-5Y/PH-5Y L=130MM
1
Q11
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
XS301
996510029488
CABLE 9PIN 140MM FH-JC20
1
Q12
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
XS800
996510022394
4PIN CABLE WITH SHIELD L=180MM
1
Q13
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
Q14
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
Q2
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
Q3
996510009671
PNP TRANSISTOR
1
Q4
996510021453
SMD. TRANSISTOR MMBT8550CLT1
1
SCREWS LIST:
Q5
996510021453
SMD. TRANSISTOR MMBT8550CLT1
1
No
Q6
996510009671
PNP TRANSISTOR
1
6
—
S/T SCREW B 2.6 X 8 BF
6
Q7
996510009671
PNP TRANSISTOR
1
11
—
S/T SCREW B3 X 6 BF
9
Q8
996510009670
TRANSISTOR SMT 3CG9012M
1
13
—
S/T SCREW B 3 X 7 BF
4
Q9
996510009669
SMD.TRANSISTOR MMBT3904LT1 NPN
1
U1
996510020916
16M SPI FLASH EON
1
U2
996510029496
ZR36966PQCG-XF2
1
U3
996510029495
16M BIT SDRAM ISC42S16100E-7TL
1
U4
996510011055
IC CD5888CB
1
U5
996510010924
Dual operational amplifier
1
Y2
996510009675
27MCL20PF
1
ASSY-PW BD COMPONENT PARTLIST
No
12NC No.
D1
996510011047
Description
DIODE IN4007
Q'ty
1
D10
996500027866
DIODE SR360 3A/60V
1
D7
996500014043
DIODE FR102 (FAST RECOVERY)
1
L1
996510009942
COIL WIDTH
1
L2
996500032509
COIL SL0811-6R8K2R4
1
T1
996510012665
TRANSFORMER CONV.
1
U1
996510010953
IC TNY176PN
1
U2
996500024838
PC123X9YFZ
1
U3
996500014609
IC AM431LP
1
ASSY-FB BD COMPONENT PARTLIST
No
12NC No.
Description
Q'ty
LED2
996500034464
LED BT-102D-31
1
LED3
996500034464
LED BT-102D-31
1
REM301
996510020925
HM338-12 RECEIVER MOD H=12MM
1
12NC No.
Description
Q'ty
9-1
REVISION LIST
Version 1.0
* Initial release for DVP3111/55 and DVP3300/93
Version 1.1
* Adding DVP3300/96