Download WamBam Fence VF13001 Installation Guide

3-Rail Vinyl Ranch Fence (2 Pack)
BOX CONTENTS
Discover the Benefits of WamBam Traditional Vinyl Fence
• Made of durable, low-maintenance white vinyl
• Post design offers architectural character and flexibility when installing fence
• Post design also offers 4-way universal directional capabilities
(you do not need to order end, line, corner or specialized gate posts)
• Limited Lifetime Warranty
.090in. wall thickness
Each Fence Panel Box
Includes:
• Post Caps (2)
• Rails (6)
• 3.5in. Stainless Steel Screws (12)
This Post & Cap
Not Included
(See note below)
• Posts (2)
PLEASE NOTE:
YOU WILL NEED TO PURCHASE ONE
EXTRA POST & CAP TO COMPLETE
EACH OF YOUR FENCE RUNS
(Extra posts are sold as 2-packs)
For more information, contact us at 1 877-778-5733.
1
3-Rail Vinyl Ranch Fence (2 Pack)
PRODUCT SPECIFICATIONS
This fence can be trimmed down both in width and
height to accommodate custom applications.
Top View
1.5in.
4.5in.
4.5in.
4.5in.
.090in. Wall Thickness
3.5in. Screw
8in.
8in.
51.5in.
50in.
72in.
Horizontal rail spacing can be
adjusted freely to lower heights.
19.5in.
Ground
2in.
79.5in.
20.5in.
84in.
36in.
Concrete Footing
10in.
For more information, contact us at 1 877-778-5733.
2
3-Rail Vinyl Ranch Fence (2 Pack)
QUICKIE OVERVIEW
• Prior to construction, check with your regulatory agency for special code requirements in your area.
• Contact your utility supplier to locate and mark underground lines before excavation.
• Sketch out the layout of your fence and calculate the number of panels, gates and posts required (order one
extra post & cap to finish each fence run).
• Careful planning & measuring of your fence is essential, as moving posts after the concrete sets is extremely difficult.
B
A
10in.
79.5in.
84in. o.c.
36in.
After stringing your fence line, dig your first post hole 10in.
diameter x 36in. deep. Dig your second hole 84in. on center to
your first hole, and so on. Dig only three or four holes at a time
to ensure proper spacing.
C
1 - Add approximately 18in. of concrete to the bottom of the hole.
2 - Install posts straight and level.
3 - Add more concrete to within 2in. of ground level.
D
In the first fence section, slide 3 rails down
the groove in your posts to the approximate
position as illustrated on page 2
(rail spacing is flexible).
In the second fence section, slide 3 rails down the groove in your posts to
the approximate position and repeat with any remaining fence sections.
For more information, contact us at 1 877-778-5733.
3
3-Rail Vinyl Ranch Fence (2 Pack)
SCREW RAILS TO POSTS
E
VERY IMPORTANT


Screws must be inserted straight and into
the correct area of the post/rail as indicated.
CORRECT
Do not overtighten
screws as it will cause
the vinyl to dimple.

TOP
VIEW
Line up and insert screws
along edge of rounded
corner radius as shown.
Fasten a 3.5 inch screw through the posts into the rails.
F
WRONG
This will ensure that your
fence rails will never fall out
of your posts like traditional
vinyl fence rails sometimes do.

WRONG

Screw has not been lined up nor inserted into the
post correctly and has missed the rail entirely.
Repeat in each rail for a total of six per panel.
For more information, contact us at 1 877-778-5733.
4
3-Rail Vinyl Ranch Fence (2 Pack)
Most yards are relatively level and will allow for a fairly simple installation. If your
yard is steeply pitched, or is very uneven, you may need to either slope, or stair-step
your panels as illustrated below. Post height can be trimmed down as necessary.
SLOPED
Ground
STAIR-STEPPED
Ground
G
Vin
y
lW
eld
1
2
GLUE CAPS ON POSTS
1 - Put a small bead of vinyl glue or weld (purchased separately at hardware store) along the inside of the cap.
2 - Place the glued cap on the vinyl post and allow to set for 5-10 minutes.
For more information, contact us at 1 877-778-5733.
5