Download Taylor Freezer 345/346/349/355 User's Manual

OPERATOR’S
MANUAL
Model 345/346/349/355
Slush Freezers
Original Operating Instructions
039710- M
6/19/01 (Original Publication)
Updated 11/22/13
Complete this page for quick reference when service is required:
Taylor Distributor:
Address:
Phone:
Fax:
E- mail:
Service:
Parts:
Date of Installation:
Information found on the data label:
Model Number:
Serial Number:
Electrical Specs:
Voltage
Cycle
Phase
Maximum Fuse Size:
A
Minimum Wire Ampacity:
A
E 2001 Carrier Commercial Refrigeration, Inc.
039710- M
Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work
may be a violation of Copyright Law of the United States of America and other countries, could result in the
awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in further
civil and criminal penalties.
All rights reserved.
Taylor Company
a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072
Table of Contents
Section 1
To the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air Cooled Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water Cooled Refrigeration Units (Water Cooled Units Only) . . . . . . . . . . . . . . . .
Water Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Syrup System Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 2
To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 3
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 4
Operator Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model 345 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model 346 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model 349 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model 355 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Door Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 5
Important: To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbol Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liquid Crystal Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operational Mode Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operator Menu Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Syrup Out Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CO2 Out Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water Out Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio Alarm Silencer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sampling Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Daily Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 6
Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Priming/Brixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
90 Day Closing Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Draining Product From the Freezing Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brush Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents
1
1
2
2
2
4
7
8
10
10
11
12
13
14
15
16
16
16
17
17
17
22
23
23
23
23
23
23
24
24
29
33
35
35
35
36
36
Models 345, 346, 349, 355
Table of Contents - Page 2
Section 7
Important: Operator Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
During Cleaning and Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting Bacterial Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Regular Maintenance Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Winter Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 8
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 9
Parts Replacement Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 10
Limited Warranty on Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 11
Limited Warranty on Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 12
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
38
38
38
38
39
40
42
43
45
48
70
Note: Continuing research results in steady improvements; therefore, information
in this manual is subject to change without notice.
Note: Only instructions originating from the factory or its authorized translation
representative(s) are considered to be the original set of instructions.
E 2001 Carrier Commercial Refrigeration, Inc.
(Updated November, 2013)
039710- M
Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work
may be a violation of Copyright Law of the United States of America and other countries, could result in the
awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in further
civil and criminal penalties.
All rights reserved.
Taylor Company
a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072
Models 345, 346, 349, 355
Table of Contents
Section 1
To the Installer
The following information has been included in the
manual as safety and regulatory guidelines. For
complete installation instructions, please see the
Installation Checklist.
This unit has many sharp edges that can
cause severe injuries.
Site Preparation
Installer Safety
Review the area where the unit will be installed before
uncrating the unit. Make sure that all possible hazards
to the user and the equipment have been addressed.
In all areas of the world, equipment should be
installed in accordance with existing local codes.
Please contact your local authorities if you have any
questions.
Air Cooled Units
Care should be taken to ensure that all basic safety
practices are followed during the installation and
servicing activities related to the installation and
service of Taylor equipment.
S
S
S
S
Air cooled units require 6” (152 mm) minimum air
space around all sides. Failure to allow adequate
clearance can reduce the refrigeration capacity of the
freezer and possibly cause permanent damage to the
compressor(s).
Only authorized Taylor service personnel
should perform installation and repairs on
the equipment.
Authorized service personnel should consult
OSHA Standard 29CFRI910.147 or the
applicable code of the local area for the
industry standards on lockout/tagout
procedures before beginning any installation
or repairs.
Authorized service personnel must ensure
that the proper PPE is available and worn
when required during installation and
service.
Authorized service personnel must remove
all metal jewelry, rings, and watches before
working on electrical equipment.
For Indoor Use Only: This unit is designed to operate
indoors, under normal ambient temperatures of
70_-75_F (21_-24_C). The freezer has successfully
performed in high ambient temperatures of
104_(40_C) at reduced capacities.
This unit must NOT be installed in an area
where a water jet or hose can be used. NEVER use a
water jet or hose to rinse or clean the unit. Failure to
follow this instruction may result in electrocution.
This unit must be installed on a level surface
to avoid the hazard of tipping. Extreme care should be
taken in moving this equipment for any reason. Two or
more persons are required to safely move this unit.
Failure to comply may result in personal injury or
equipment damage.
The main power supply(s) to the freezer must
be disconnected prior to performing any repairs.
Failure to follow this instruction may result in personal
injury or death from electrical shock or hazardous
moving parts as well as poor performance or damage
to the equipment.
Uncrate the unit and inspect it for damage. Report any
damage to your Taylor Distributor.
This piece of equipment is made in the USA and has
USA sizes of hardware. All metric conversions are
approximate and vary in size.
Note: All repairs must be performed by an
authorized Taylor Service Technician.
131122
Models 345, 346, 349, 355
1
To the Installer
Water Cooled Refrigeration Units
IMPORTANT: The water filter (064422- SER) must
be thoroughly flushed with water before connecting it
to the machine. This removes carbon particles that
could clog the flow control. To flush the filter,
connect the inlet end of the filter to the water supply.
Position the outlet end of the filter over an empty
pail. Open the water supply. Allow water to flow
through the filter until the water exiting the filter is
clear. Close the water supply. Attach the outlet end
of the filter to the machine. Reopen the water
supply.
(Water Cooled Units Only)
Failure to use adequate size water lines may cause the
unit to go off on high head pressure and shut down.
Depending on local water conditions, it may be
advisable to install a water strainer to prevent foreign
substances from clogging the automatic water valve.
There are two water “in” connections and one water
“out” line connection. DO NOT install a hand shut-off
valve on the water “out” line! Water should always
flow in this order: first, through the automatic water
valve; second, through the condenser; and third,
through the outlet fitting to an open trap drain.
IMPORTANT: Water pressures are pre-set at the
factory. Do not adjust the water. Improper water
adjustments may cause operation discrepancies.
A back flow prevention device is required
on the incoming water connection side. Please
refer to the applicable National, State, and local codes
for determining the proper configuration.
Figure 1
Electrical Connections
Water Connections
In the United States, this equipment is intended to be
installed in accordance with the National Electrical
Code (NEC), ANSI/NFPA 70- 1987. The purpose of
the NEC code is the practical safeguarding of persons
and property from hazards arising from the use of
electricity. This code contains provisions considered
necessary for safety. Compliance therewith and
proper maintenance will result in an installation
essentially free from hazard! In all other areas of the
world, equipment should be installed in accordance
with the existing local codes. Please contact your local
authorities.
An adequate cold water supply must be provided
with a hand shut-off valve. On the back of the unit, a
3/8” (9.5 mm) M.F.L. water connection has been
provided for easy hook-up. A flexible line is
recommended, if local codes permit. A minimum of
25 psi water pressure is required to avoid having the
unit cut out the low water pressure switch. A booster
pump must be provided if this pressure is not
available.
Note: Water lines beyond 200 ft. (61 m) require 1/2”
(13 mm) water lines.
FOLLOW YOUR LOCAL ELECTRICAL CODES!
INSTALL POTABLE WATER CONNECTION
WITH ADEQUATE BACK-FLOW
PROTECTION TO COMPLY WITH
APPLICABLE NATIONAL, STATE AND
LOCAL CODES.
Each unit requires one power supply for each data
label on the unit. Check the data label(s) on the freezer
for branch circuit overcurrent protection or fuse, circuit
ampacity, and other electrical specifications. Refer to
the wiring diagram provided inside of the control box
for proper power connections.
It is always a good practice to have a filter system to
improve the quality of the water and to avoid
clogging the operating components.
120828
To the Installer
2
Models 345, 346, 349, 355
Beater Rotation
CAUTION: THIS EQUIPMENT MUST BE
PROPERLY GROUNDED! FAILURE TO DO SO
CAN RESULT IN SEVERE PERSONAL INJURY
FROM ELECTRICAL SHOCK!
Beater rotation must be clockwise as viewed
looking into the freezing cylinder.
Note: The following procedures should be
performed by a trained service technician.
DO NOT operate this freezer with larger fuses
than specified on the unit data label. Failure to follow
this instruction may result in electrocution or damage
to the machine.
To correct the rotation on a three- phase unit,
interchange any two incoming power supply lines at
freezer main terminal block only.
To correct rotation on a single- phase unit, change the
leads inside the beater motor. (Follow the diagram
printed on the motor.)
This unit is provided with an equipotential
grounding lug that is to be properly attached to the rear
of the frame by the authorized installer. The installation
location is marked by the equipotential bonding
symbol (5021 of IEC 60417-1) on both the removable
panel and the equipment’s frame.
Initial Freezing Cylinder Cleaning
Due to the types of products used in FCB equipment,
it is imperative that the freezing cylinder and the inlet
tube be thoroughly brush cleaned, rinsed, and
sanitized before running any product.
Stationary appliances which are not equipped
with a power cord and a plug or another device to
disconnect the appliance from the power source must
have an all-pole disconnecting device with a contact
gap of at least 3 mm installed in the external
installation.
Prepare a cleaning solution, using 2 oz. of liquid
detergent in 2 gallons of warm water. Using this
solution, brush clean the freezing cylinder and the inlet
tube. Rinse the freezing cylinder and the inlet tube with
clean water and then sanitize, using the sanitizing
procedures outlined in this Operator Manual, starting
on page 29.
Appliances that are permanently connected to
fixed wiring and for which leakage currents may
exceed 10 mA, particularly when disconnected or not
used for long periods, or during initial installation, shall
have protective devices such as a GFI, to protect
against the leakage of current, installed by the
authorized personnel to the local codes.
Refrigerant
In consideration of our environment, Taylor
uses only earth friendly HFC refrigerants. The HFC
refrigerant used in this unit is R404A. This refrigerant
is generally considered non-toxic and non-flammable,
with an Ozone Depleting Potential (ODP) of zero (0).
Supply cords used with this unit shall be
oil-resistant, sheathed flexible cable not lighter than
ordinary polychloroprene or other equivalent synthetic
elastomer-sheathed cord (Code designation 60245
IEC 57) installed with the proper cord anchorage to
relieve conductors from strain, including twisting, at
the terminals and protect the insulation of the
conductors from abrasion.
However, any gas under pressure is potentially
hazardous and must be handled with caution.
NEVER fill any refrigerant cylinder completely with
liquid. Filling the cylinder to approximately 80% will
allow for normal expansion.
120828
Models 345, 346, 349, 355
3
To the Installer
Use only R404A refrigerant that conforms to
the AHRI standard 700 specification. The use of any
other refrigerant may expose users and operators to
unexpected safety hazards.
4.
Refrigerant liquid sprayed onto the skin may
cause serious damage to tissue. Keep eyes and skin
protected. If refrigerant burns should occur, flush
immediately with cold water. If burns are severe, apply
ice packs and contact a physician immediately.
c.
Be sure all control switches on the front panel
are in the “OFF” position.
d.
The freezer must be properly grounded.
A harness with three nylobrade tubes feeds
through the base pan and exits the rear of the
freezer. (The Model 355 is equipped with four
tubes.)
a.
Connect the CO2 line to the CO2 regulator
that is closest to the CO2 tank (primary
regulator). This line will supply CO2 to the
freezer.
Taylor reminds technicians to be cautious of
government laws regarding refrigerant recovery,
recycling, and reclaiming systems. If you have any
questions regarding these laws, please contact the
factory Service Department.
WARNING: R404A refrigerant used in
conjunction with polyolester oils is extremely moisture
absorbent. When opening a refrigeration system, the
maximum time the system is open must not exceed 15
minutes. Cap all open tubing to prevent humid air or
water from being absorbed by the oil.
Figure 2
b.
Syrup System Connections
1.
Water pipe connections and fixtures directly
connected to a potable water supply shall be
sized, installed and maintained according to
federal, state and local laws.
2.
Hook up cold water supply to freezer to supply
water to the carbonator. A minimum of 21 PSI
of water pressure is required at the low
pressure switch. The low pressure switch will
cause the entire freezer to shut down if the
water pressure drops below 7 PSI for longer
than one minute.
Note: For Bag-in-Box units (BIB), connect the #1 line
to the Bag-In-Box instead of the syrup tank.
The water regulator should be set at 35 PSI.
When the power switch is turned on the water
pump will immediately activate to maintain water
pressure.
3.
Figure 3
Electrical Hook-Up
a.
One power cord.
b.
Refer to the data label.
Connect the #1 line to the syrup tank for the
left side of the freezer as viewed from the
front of the machine. This line will supply
syrup to the left syrup sentry.
c.
Connect the #2 line to the syrup tank (or the
Bag-in-Box) for the right side of the freezer.
This line will supply syrup to the right syrup
sentry.
131122
To the Installer
4
Models 345, 346, 349, 355
d.
5.
6.
Connect the #4 line on the Model 355 to the
water regulator on the remote carbonator.
This line monitors the water pressure
supplied to the unit.
Set the primary regulator on the CO2 tank to 90
PSI (6.2 BAR).
There are two spare CO2 lines provided. Use
one of the spare CO2 lines to connect one end
to the individual regulator (secondary regulator)
and the other end to the first syrup tank. Use
the other spare CO2 line to connect the CO2 to
the second syrup tank.
Figure 6
7.
Set the secondary regulator on the CO2 tank to
60 PSI (4.1 BAR) for the syrup tanks or the BIB
pumps.
Figure 4
Note: For Bag-in-Box units, connect the CO2 lines to
the Bag-in-Box pumps instead of the syrup tanks.
Figure 7
Figure 5
Models 345, 346, 349, 355
5
8.
Turn the cold water supply on.
9.
Check for CO2 leaks. This can be done by
closing the valve on the top of the CO2 tank.
Watch the high pressure gauge; it should hold
pressure. If it does not, there is a CO2 leak.
Use a soap solution to locate and repair the
leak.
To the Installer
10.
11.
For Bag-in-Box syrup delivery system, connect
the two spare CO2 lines from the secondary
regulator to each “Gas In” fitting on the pumps.
Set secondary regulator pressure to 60 PSI
(4.1 BAR) depending on the length of syrup line
run to the unit.
Important: Ensure that the Bag-in-Box switch is
enabled.
The CO2 regulator assembly (primary regulator)
inside the freezer should be set at 60 PSI (4.1
BAR). The secondary regulator, located inside
the freezer just behind the primary regulator,
can be adjusted from 20 to 25 PSI. (The factory
recommendation is 20 PSI.) Increasing the
pressure from 20 PSI will increase the overrun.
You should always stay within the 20 to 25 PSI
range as the gauge reflects the pressure in the
hopper and barrel. The setting will be
determined by the desired overrun and the
syrup used.
To the Installer
6
12.
The CO2 low pressure switch requires at least
74 PSI before the freezer will start. It is set to
cut out at 60 PSI and in at 74 PSI.
13.
The pressure relief valve on the hopper cover is
set to relieve at 30 PSI in case of excess
pressure in the hopper.
14.
There are check valves in the CO2, syrup, and
water lines to prevent any back flow of soda
water, product, or CO2.
15.
The CO2 solenoids which supply CO2 to the
hoppers are wired to provide CO2 in all control
settings except “DEFROST” and “OFF”.
Models 345, 346, 349, 355
Section 2
To the Operator
The freezer(s) you have purchased has been carefully
engineered and manufactured to give you dependable
operation.
compliant with the EU Directive as well as other similar
legislation in effect after August 13, 2005. Therefore,
it must be collected separately after its use is
completed, and cannot be disposed as unsorted
municipal waste. The user is responsible for returning
the product to the appropriate collection facility, as
specified by your local code.
This unit(s), when properly operated and cared for, will
produce a consistent quality product. Like all
mechanical products, this machine will require
cleaning and scheduled maintenance. A minimum
amount of care and attention is necessary if the
operating procedures outlined in this manual are
followed closely.
For additional information regarding applicable local
laws, please contact the municipal facility and/or local
distributor.
This Operator’s Manual should be read before
operating or performing any maintenance on your
equipment.
Compressor Warranty Disclaimer
The refrigeration compressor(s) on this unit are
warranted for the term stated in the Limited Warranty
section in this manual. However, due to the Montreal
Protocol and the U.S. Clean Air Act Amendments of
1990, many new refrigerants are being tested and
developed, thus seeking their way into the service
industry. Some of these new refrigerants are being
advertised as drop- in replacements for numerous
applications. It should be noted that in the event of
ordinary service to this unit’s refrigeration system,
only the refrigerant specified on the affixed data
label should be used. The unauthorized use of
alternate refrigerants will void your Taylor compressor
warranty. It is the unit owner’s responsibility to make
this fact known to any technician he employs.
Your freezer will NOT eventually compensate and
correct for any errors during the set-up or filling
operations. Thus, the initial assembly and priming
procedures are of extreme importance. It is strongly
recommended that all personnel responsible for the
equipment’s operation study these procedures
together in order to be properly trained and to make
sure that no misunderstandings exist.
In the event you should require technical assistance,
please contact your local authorized Taylor Distributor
for service.
Note: Your Taylor warranty is valid only if the parts are
authorized Taylor parts, purchased from the local
authorized Taylor Distributor, and only if all required
service work is provided by an authorized Taylor
service technician. Taylor reserves the right to deny
warranty claims on units or parts if non- Taylor
approved parts or incorrect refrigerant were installed
in the unit, system modifications were performed
beyond factory recommendations, or it is determined
that the failure was caused by abuse, misuse, neglect,
or failure to follow all operating instructions. For full
details of your Taylor Warranty, please see the Limited
Warranty section in this manual.
It should also be noted that Taylor does not warrant the
refrigerant used in its equipment. For example, if the
refrigerant is lost during the course of ordinary service
to this machine, Taylor has no obligation to either
supply or provide its replacement either at billable or
unbillable terms. Taylor does have the obligation to
recommend a suitable replacement if the original
refrigerant is banned, obsoleted, or no longer available
during the five year warranty of the compressor.
Taylor will continue to monitor the industry and test
new alternates as they are being developed. Should a
new alternate prove, through our testing, that it would
be accepted as a drop-in replacement, then the above
disclaimer would become null and void. To find out the
current status of an alternate refrigerant as it relates to
your compressor warranty, call the local Taylor
Distributor or the Taylor Factory. Be prepared to
provide the Model/Serial Number of the unit in
question.
Note: Constant research results in steady
improvements; therefore, information in this
manual is subject to change without notice.
If the crossed out wheeled bin symbol is
affixed to this product, it signifies that this product is
131122
Models 345, 346, 349, 355
7
To the Operator
Section 3
Safety
We at Taylor are concerned about the safety of the
operator when he or she comes in contact with the
freezer and its parts. Taylor has gone to extreme
efforts to design and manufacture built- in safety
features to protect both you and the service technician.
As an example, warning labels have been attached to
the freezer to further point out safety precautions to the
operator.
IMPORTANT - Failure to adhere to the
following safety precautions may result in severe
personal injury or death. Failure to comply with
these warnings may damage the machine and its
components. Component damage will result in
part replacement expense and service repair
expense.
S
DO NOT operate the freezer unless it is
properly grounded.
S
DO NOT operate the freezer with larger fuses
than specified on the freezer data label.
S
All repairs must be performed by an
authorized Taylor service technician.
S
The main power supplies to the machine must
be disconnected prior to performing any
repairs.
For Cord Connected Units: Only Taylor
authorized service technicians or licensed
electricians may install a plug or replacement
cord on these units.
S
DO NOT operate the freezer without reading
this Operator Manual. Failure to follow this instruction
may result in equipment damage, poor freezer
performance, health hazards, or personal injury.
This appliance is to be used only by trained
personnel. It is not intended for use by children or
people with reduced physical, sensory, or mental
capabilities, or lack of experience and knowledge,
unless given supervision or instruction concerning the
use of the appliance by a person responsible for their
safety. Children should be supervised to ensure that
they do not play with the appliance.
S
Stationary appliances which are not equipped
with a power cord and a plug or another device
to disconnect the appliance from the power
source must have an all-pole disconnecting
device with a contact gap of at least 3 mm
installed in the external installation.
S
Appliances that are permanently connected to
fixed wiring and for which leakage currents
may exceed 10 mA, particularly when
disconnected, not used for long periods, or
during initial installation, shall have protective
devices such as a GFI to protect against the
leakage of current, installed by authorized
personnel to the local codes.
Supply cords used with this unit shall be
oil-resistant, sheathed flexible cable, not
lighter than ordinary polychloroprene or other
equivalent synthetic elastomer-sheathed cord
(Code designation 60245 IEC 57) installed
with the proper cord anchorage to relieve
conductors from strain, including twisting, at
the terminals and protect the insulation of the
conductors from abrasion.
S
This unit is provided with an equipotential
grounding lug that is to be properly attached to the rear
of the frame by the authorized installer. The installation
location is marked by the equipotential bonding
symbol (5021 of IEC 60417-1) on both the removable
panel and the equipment’s frame.
If the supply cord is damaged, it must be
replaced by an authorized Taylor service
technician in order to avoid a hazard.
DO NOT use a water jet to clean or rinse the
freezer. Failure to follow these instructions may result
in serious electrical shock.
Failure to follow these instructions may result in
electrocution. Contact your local authorized Taylor
Distributor for service.
131122
Safety
8
Models 345, 346, 349, 355
S
DO NOT allow untrained personnel to
operate this machine.
S
DO NOT operate the freezer unless all
service panels and access doors are
restrained with screws.
Cleaning and sanitizing schedules are
governed by your state or local regulatory agencies
and must be followed accordingly. Please refer to the
cleaning section of this manual for the proper
procedure to clean this unit.
DO NOT remove any internal operating
parts (example: freezer door, beater,
scraper blades, etc.) unless all control
switches are in the OFF position and ALL
PRESSURE IN THE FREEZING
CYLINDER HAS BEEN RELIEVED.
Failure to follow these instructions may result in
contaminated product or severe personal injury to
fingers or hands from hazardous moving parts.
This machine is designed to maintain product
temperature under 41_F (5_C). Any product being
added to this machine must be below 41_F (5_C).
Failure to follow this instruction may result in health
hazards and poor freezer performance.
S
CAUTION: This unit is pressurized when in
operation. The control switch must be in the OFF
position until the unit is completely assembled. No part
should ever be removed from the machine while it is in
operation. No part should be removed until the control
switch has been turned to the OFF position and all
pressure has been relieved by opening the draw valve.
This unit has many sharp edges that can
cause severe injuries.
S
S
Failure to follow these instructions may result in severe
personal injury from hazardous moving parts or from
the impact of propelled parts.
DO NOT put objects or fingers in the door
spout. This may contaminate the product
and cause severe personal injury from blade
contact.
IMPORTANT: DO NOT obstruct air intake and
discharge openings: These units require 6” (152 mm)
minimum air space around all sides. Failure to follow
this instruction may cause poor freezer performance
and damage to the machine.
USE EXTREME CAUTION when removing
the beater asssembly. The scraper blades
are very sharp.
For Indoor Use Only: This unit is designed to operate
indoors, under normal ambient temperatures of
70_-75_F (21_-24_C). The freezer has successfully
performed in high ambient temperatures of
104_(40_C) at reduced capacities.
This freezer must be placed on a level
surface. Failure to comply may result in personal injury
or equipment damage.
DO NOT run the unit without product. Failure to follow
this instruction can result in damage to the unit.
Access to the service area of the unit must be
restricted to persons having knowledge and practical
experience with the unit, in particular as far as safety
and hygiene are concerned.
NOISE LEVEL: Airborne noise emission does not
exceed 78 dB(A) when measured at a distance of 1.0
meter from the surface of the machine and at a height
of 1.6 meters from the floor.
131122
Models 345, 346, 349, 355
9
Safety
Section 4
Operator Parts Identification
Model 345
2
1
3
16
15
14
17
4
13
12
18
11
5
6
10
8
7
9
Item
Description
Part No.
Item
Description
Part No.
1
Panel A.-Side Left
X45136
11
Panel-Service
044916
2
Hood
044618
12
Panel-Front-Lower
043599-BLA
3
Panel-Rear
044921-SP1
13
Stud-Nose Cone 5/16-18
020445
4
Panel A.-Side Right
X44919
*13a Washer-Freezer Stud
036265
5
Caster-Swivel 3/4-10 St. 3”
021279
14
Card-Flavor Packet
035324
6
Caster-Locking Swivel - 3”
030307
15
Card-FCB POP
043957
7
Lock-Caster Bracket
032571
16
Panel-Front-Upper
043600-BLA
8
Shield-Splash
043719
17
Plate A.-Dec-345-346-355 Black
043639-BLA
9
Tray-Drip *345/6* Black w/Drain
043720-SP
18
Decal- Dec- Taylor Domed
053761
Pan-Drip 19-1/2 Long
035034
Pan-Drip (White) For Drip Guide
043612
10
*19
*Not Shown
Operator Parts Identification
10
Models 345, 346, 349, 355
Model 346
3
2
1
15
14
16
13
17
12
18
4
5
8
10
19
9
11
Item
Description
Part No.
1
Panel A.-Side Left
X44917
2
Hood
3
Panel-Rear
4
Item
20
6 7
Description
Part No.
12
Panel-Front-Lower
043599-BLA
044618
13
Stud-Nose Cone 5/16-18
020445
044921-SP1
*13a Washer-Freezer Stud
036265
Panel A.-Side *346*AC*R*Filter
X53611
14
Card-Flavor Packet
035324
5
Caster-Swivel 3/4-10 St. 3”
021279
15
Card-FCB POP
043957
6
Caster-Locking Swivel 3”
030307
16
Panel-Front-Upper
043600-BLA
7
Lock-Caster Bracket
032571
17
Plate-Dec-345-346-355* Black
043639-BLA
8
Shield-Splash
043719
18
Decal- Dec- Taylor Domed
053761
9
Tray-Drip 20” L x 8” D x 3-3/4
043720-SP
19
Filter- Air 18L x 16.5H x .70W AC
052779- 1
10
Pan-Drip 19-1/2 Long
035034
20
Cover- Hole- Filter- Snap In
053801
11
Panel-Service *346* Filter
053612
*21
Pan-Drip (White) For Drip Guide
043612
*Not Shown
Models 345, 346, 349, 355
11
Operator Parts Identification
Model 349
2
1
3
14
13
15
12
11
4
17
16
5
6
10
7
18
9
Item
Description
Part No.
Item
8
Description
Part No.
1
Panel A.-Side Left
X42289
12
Stud-Nose Cone 5/16-18
020445
2
Hood
042166
*12a
Washer-Freezer Stud
036265
3
Panel-Rear *349* Drain Hole
042198
13
Card-Flavor Packet
035324
4
Panel A.-Side Right
X42291
14
Panel-Front Upper
042081-BLA
5
Caster-Swivel 3/4-10 St. 3”
021279
15
Plate-Dec *349* Black
035410-BLA
6
Caster-Locking Swivel 3”
030307
16
Decal- Dec- Taylor Domed
053761
7
Lock-Caster Bracket
032571
17
Cover- Hole- Filter- Snap In
053801
8
Panel-Service *349* AC
053652
18
Filter- Air 18 L x 16.5 H x .7 W
052779- 1
9
Tray-Drip (Black) w/Drain
038275-SP
*19
Pan A.-Drip w/Hose Left
X42201
10
Shield-Splash
038276
*20
Pan A.-Drip w/Hose Right
X42203
11
Panel-Front-Lower
042082-BLA
*Not Shown
Operator Parts Identification
12
Models 345, 346, 349, 355
Model 355
3
2
4
1
14
5
13
12
12a
15
11
6
10
7
9
8
Item
Description
Part No.
Item
Description
Part No.
1
Panel-Front -Upper
043600-BLA
10
Pan-Drip
035034
2
Panel-Side-Left
044619-SP
11
Panel-Front-Lower
043599-BLA
3
Hood
044618
12
Stud-Nose Cone 5/16-18
020445
4
Panel-Rear-Stainless
044621-SS
*12a
Washer-Freezer Stud
036265
5
Panel-Side-Right
044620-SP
13
Card-Flavor Packet
035324
6
Leg-4” 3/8-16 Stud
036397
14
Card-FCB POP
043957
7
Shelf-Drip Tray
049697
15
Plate-Dec-345-346-355 Black
043639-BLA
8
Tray-Drip 20” L x 8” D x 3-3/4
043720
*16
Pan-Drip (White) For Drip Guide
043612
9
Shield-Splash
043719
*Not Shown
Models 345, 346, 349, 355
13
Operator Parts Identification
Door Assembly
ITEM
DESCRIPTION
PART NO.
ITEM
DESCRIPTION
PART NO.
1
DOOR
1m
O-RING-1.129 ODX.989ID
039219
1a
CAP-SPOUT-DOOR-FCB-BLK
046191-BLA
1n
NUT-SPOUT-DOOR-PRESS.
039323
1b
SPRING-COMP.480X.072X3.0
039320
2
NUT-STUD
043666
1c
VALVE-DRAW-DOOR-PRESS.
039324
3
O-RING-9/16 OD X .103W
016369
O-RING-5-1/4ODX.210W
(DOOR)
017003
1d
1e
SPOUT-DOOR-FCB-BLACK
046190-BLA
4
BEARING-FRONT-PRESSURE
039349
5
BEATER-PLASTIC-FCB-PRESS.
041182
6
BLADE-SCRAPER-FCB-16INCH
041103
7
SHAFT-BEATER-SLUSH-PRES
039337
8
SEAL-DRIVE SHAFT
032560
9*
O-RING-7/8 OD X .139W
(BEATER SHAFT)
025307
10
BUSHING-BEATER
SHAFT/BOOT SEAL
042278
1f
HANDLE-DRAW-FCB-BLACK
046192-BLA
1g
PIN-PIVOT-SPOUT-DOOR
039321
1h
SLIDE-HANDLE-DOOR-BLK
046193-BLA
1i
SCREW-10-32X3/8PHL-TRUS
HD SS
053869
1j
O-RING-9/32 OD X 1/16 WALL
029751
1k
PLUG-PRIME-SLUSH-PRESS.
039568
1l
DOOR-FREEZER-SLUSH-PRES
039573
*NOTE: O-RING 025307 IS NOT USED ON CURRENT
MODELS. HOWEVER, UNITS BUILT PRIOR TO 10/09
THAT HAVE NOT BEEN UPDATED WITH METAL
REAR SHELL BEARING X67222 STILL REQUIRE
O-RING.
120828
Operator Parts Identification
14
Models 345, 346, 349, 355
Accessories
2
1
3
4
5
KAY-5
6
8
R
7
®
Sanitizer/Cleaner
KEEP OUT OF REACH OF CHILDREN
CAUTION
FOR INSTITUTIONAL USE ONLY
1 OZ (28.4 g)
048260
ITEM
DESCRIPTION
PART NO.
ITEM
DESCRIPTION
PART NO.
1
PAIL-MIX 10 QT
013163
6
KIT A.-TUNE UP
X39699
2
BRUSH-MIX PUMP BODY-3”X7”
023316
7
LUBRICANT-TAYLOR HI PERF
048232
3
BRUSH-DOUBLE ENDED
013072
8
SANITIZER KAY-5 25 PACKETS
041082
4
BRUSH-REAR BRG 1”DX2“L
013071
*
SANITIZER STERA-SHEEN
010425
5
BRUSH-DRAW VALVE 1-1/2”OD
014753
Models 345, 346, 349, 355
*NOT SHOWN
15
Operator Parts Identification
Section 5
Important: To the Operator
Figure 8
Item
1
2
3
4
5
6
The following chart identifies the symbol definitions
used on the Model 349.
Description
Control Switch
Liquid Crystal Display
Keypad- Left
Keypad- Right
Product Light- Left Side
Product Light- Right Side
= ON
= OFF
= AUTO
= PRIME
= BEATER MOTOR
= ALARM SILENCE
= MENU/SELECT
Symbol Definitions
Control Switch
To better communicate in the International arena, the
words on many of our operator switches and keys have
symbols to indicate their functions. The Model 349 is
designed with these International symbols.
Important: To the Operator
The control switch is located on the top of the control
channel. When placed in the ON position, allows
Slushtecht operation.
16
Models 345, 346, 349, 355
Liquid Crystal Display
Pressing both AUTO keys will display this screen.
AUTO
OK
The Liquid Crystal Display (LCD) is located on the front
control panel. The LCD is used to show the current
operating mode of the freezing cylinders. The LCD
also indicates whether there is enough syrup, CO2,
and water being supplied to the freezer. If an error in
the machine operation occurs, a warning tone will
sound and the word “FAULT” will flash on the third line
of the display.
MODE
SYRUP
CO2=OK
AUTO
OK
WATER=OK
Line 1 indicates the operating mode for each cylinder.
Line 2 indicates the status of the syrup systems in each
freezing cylinder.
Line 3 indicates if there is a fault in the system (left
side).
The same rules apply to the fourth line which indicates
the status of the CO2 and the H2O.
Operational Mode Display
AUTO
OK
- - FAULT- CO2=OK
When the unit is plugged into the wall receptacle and
the power switch is placed in the ON position, this
screen appears.
MODE
SYRUP
OPERATOR MENU
ABCDEFGH
EXIT MENU
<- - - ->
SEL
Operator Menu Timeout
OFF
OK
If the display is left in the operator menu or any of the
operator menu selections, except for Current
Conditions, the display will return to the system mode
screen 60 seconds after the last keypress. The
Current Conditions screen will be displayed until
manually changed.
WATER=OK
Note: Syrup, CO2 and water are satisfied.
Models 345, 346, 349, 355
WATER=OK
The OPERATOR MENU is used to enter into the
operating screens. To access the OPERATOR MENU,
simply press the word “MENU”. The cursor will flash
under the letter “A”, indicating that this is screen A. To
select a different screen, use the arrow keys to move
the cursor to the desired screen selection and press
the SEL key.
This display will remain on the LCD for 60 seconds
unless a key is pressed. If any key is pressed (or 60
seconds passes), then the next screen appears.
CO2=OK
OFF
OK
Operator Menu Display
SAFETY TIMEOUT
ANY KEY ABORTS
OFF
OK
MODE
SYRUP
17
Important: To the Operator
Finding Current Fault Conditions
2.
Screen B is FAULT DESCRIPTION. The fault
description will indicate if there is a fault in one of the
freezing cylinders. When the actual fault is corrected,
the warning tone will stop. Only items 9 and 10 require
pressing the OFF/<--- key to clear the fault message
and the warning tone.
FAULT DESCRIPTION
L: BEATER OVERLOAD
R: BEATER OVERLOAD
CLR
+++
Fault Messages
Beater Overload
Beater is out on overload.
Chk Refrig Sys Psi
Compressor is out on high
head pressure (or low
suction pressure = option
that applies to some units)
Thermistor Short
Shorted thermistor probe.
Thermistor Open
Open thermistor probe.
H2O Pressure Low
Water pressure is low.
CO2 Pressure Low
CO2 pressure is low.
3.
Syrup Pressure Low Syrup is no longer present.
BRL Temp 2 High
Freezing cylinder is not
cooling after 5 minutes.
No Fault Found
No fault conditions are
apparent.
4.
SEL
CHK REFRIG SYS PSI - Compressor is out on
high head pressure (or low suction pressure =
option that applies to some units). When this
fault occurs, the machine automatically turns
off. The fault clears when the condition is
corrected.
FAULT DESCRIPTION
L: CHK REFRIG SYS PSI
R: CHK REFRIG SYS PSI
CLR
+++
Freezing cylinder
temperature is above 120_F
(49_C).
BRL Not Cooling
BEATER OVERLOAD - Beater motor is out on
overload. When this fault occurs, the machine
automatically turns off. The fault clears when
the condition is corrected.
SEL
THERMISTOR SHORT - One or both of the
barrel (freezing cylinder) thermistor probes are
faulty.
The following are explanations of the possible faults
and the display screens.
FAULT DESCRIPTION
L: THERMISTOR SHORT
R: NO FAULT FOUND
CLR
+++
Lines 2 and 3 indicate the faults found in the left and
right freezing cylinders respectively. The screen below
indicates that no faults exist on either side. To see if
there is more than one fault, press the +++ key.
Note: On a Model 349, faults for freezing cylinders 1
and 2 are shown on the first screen. Press the SEL key
to read fault messages for freezing cylinders 3 and 4.
1.
5.
NO FAULT FOUND - No fault conditions are
apparent.
FAULT DESCRIPTION
L:
NO FAULT FOUND
R:
NO FAULT FOUND
CLR
+++
THERMISTOR OPEN - One or both of the
barrel (freezing cylinder) thermistor probes are
faulty.
FAULT DESCRIPTION
L: THERMISTOR OPEN
R: NO FAULT FOUND
CLR
+++
SEL
SEL
SEL
060801
Important: To the Operator
18
Models 345, 346, 349, 355
6.
SYRUP PRESS LOW - When the syrup out
indicator displays a lack of syrup, a 15 minute
internal timer will start. At this time, no
refrigeration or product flow from the flow
control will be allowed. Only the beater and
CO2 operate. If the syrup is not replenished at
the end of the 15 minutes, the freezing cylinder
will shut down and this fault message will
appear. Replenish the syrup, and the fault
message and warning tone will clear. If using a
tank system, priming may be required.
(Example shown is for the right side.)
FAULT DESCRIPTION
L: NO FAULT FOUND
R: SYRUP PRESS LOW
CLR
+++
7.
10.
SEL
Models 345, 346, 349, 355
SEL
BRL TEMP 2 HIGH - A maximum allowable
product temperature has been established to
prevent product from excessive heating. If the
product exceeds 120_F (49_C) temperature for
any reason (in any mode of operation), the
entire unit shuts down.
FAULT DESCRIPTION
L: BARREL TEMP 2 HIGH
R: NO FAULT FOUND
CLR
+++
H2O PRESSURE LOW - When the water out
indicator displays a lack of water, a 60 second
internal timer will start. If the water is not
replenished at the end of the 60 seconds, all
freezing cylinders will shut down and this fault
message will appear. Replenish the water and
the fault message and warning tone will clear.
FAULT DESCRIPTION
L: H2O PRESSURE LOW
R: H2O PRESSURE LOW
CLR
+++
BRL NOT COOLING - A freezing cylinder
check has been established for the AUTO
mode of operation. If a freezing cylinder enters
the AUTO mode, the control will check product
temperature. After five minutes, it will again
check product temperature. If product
temperature does not drop in that five minute
time span, the freezing cylinder will shut down
and this message will appear on the fault
screen. For this check to be valid, the product
temperature must be above 40_F (4.4_C), and
the fill switch cannot be activated. If a fill
condition exists during this time, the five minute
check will be re-initiated.
FAULT DESCRIPTION
L: BARREL NOT COOLING
R: NO FAULT FOUND
CLR
+++
SEL
CO2 PRESSURE LOW - When the CO2 out
indicator displays a lack of CO2, a 60 second
internal timer will start. If the CO2 is not
replenished at the end of the 60 seconds, both
freezing cylinders will shut down and this fault
message will appear. Replenish the CO2 and
the fault message and warning tone will clear.
FAULT DESCRIPTION
L: CO2 PRESSURE LOW
R: CO2 PRESSURE LOW
CLR
+++
8.
9.
SEL
Faults, when corrected, are cleared from the fault
description screen, with the following exceptions: BRL
NOT COOLING and BRL TEMP 2 HIGH. These faults
require the operator to press the OFF key (when in the
FAULT DESCRIPTION screen) in order for the fault to
discontinue.
To see if there is more than one fault in either freezing
cylinder, press the plus key. To return to the
OPERATOR MENU, press the SEL key once. To
return to the Main Screen, use the right arrow key to
cycle to MENU ITEM A, then press the SEL key.
SEL
19
Important: To the Operator
Screen C is SET CLOCK. Move the cursor under the
number you wish to change. Press the +++ key to
increase the number; press the - - - key to decrease
the number. When the desired time and date appears,
press the SEL key once to return to the OPERATOR
MENU.
Repeat the procedure for the right side of the unit.
MANUAL DEFROST
RIGHT SIDE
Note: The clock is programmed with military time.
SET CLOCK
14:30
<- - - ->
YES
<- - - - - - >
NO
SEL
6/25/01
+++
- - -
Note: The models 345 and 355 allow only one
freezing cylinder to be defrosted at a time. This applies
to freezing cylinder pairs on the model 349. Attempting
to place a freezing cylinder into defrost while the other
freezing cylinder is defrosting will result in the following
screen. (Model 346 does not have this restriction.)
SEL
This screen will appear if an invalid date is entered.
(example: If the date entered exceeds the days of that
month.)
SET CLOCK
14:30
02/31/01
INVALID DATE
SEL
ALREADY IN DEFROST
This screen allows the Daylight Saving Time options.
DAYLIGHT SAVING TIME
DISABLE
ENABLE
<- - - - - - >
Press the SEL key to return the unit to the OPERATOR
MENU.
SEL
If the Daylight Saving Time option is enabled, then the
time will be advanced by one hour at 2:00 a.m. on the
first Sunday in April, and will be retarded by one hour
at 2:00 a.m. on the last Sunday in October.
Screen E is SYSTEM INFORMATION. It consists of
6 display features.
Press the SEL key to advance to the next feature.
Screen D is MANUAL DEFROST. This screen allows
the operator to manually defrost the left side of the
unit.
The first feature indicates the software version.
Place the cursor under YES, press the SEL key, and
the command will be executed.
MANUAL DEFROST
LEFT SIDE
<- - - - - - >
YES
SYSTEM INFORMATION
355 CONTROL UVC2
VERSION 2.03
NO
SEL
SEL
041011
Important: To the Operator
20
Models 345, 346, 349, 355
The second feature indicates the bill of material
number and the serial number.
POWER SAVER STANDBY
SUN
CYCLE 1
SUN
+++
- - -
It also indicates if the unit is equipped with a water
pressure switch.
Each freezing cylinder has eight possible defrost times
(cycles) for each day of the week. If all seven days
have the same time for a given cycle, then the following
screen will appear. This example shows that ALL
seven days have CYCLE 1 programmed for 9:00.
Press the +++ or - - - keys to view other cycles.
SEL
The third feature indicates the version number of the
language and text.
SYSTEM INFORMATION
LANGUAGE
VERSION 1.05
ENGLISH 386
DEFROST TIME LEFT
ALL
CYCLE 1
SEL
+++
The fourth feature will display the Power Saver Mode,
as OFF, REST, or STANDBY.
- - -
09:00
SEL
If one or more days of the week have a given cycle
programmed at different times, then the following
display will appear. This example shows that Sunday’s
CYCLE 1 is programmed for 9:00. The fact that SUN
is displayed (instead of ALL) indicates that some other
day(s) CYCLE 1 is programmed for a different time (or
not programmed at all). Using the cursor keys, place
the cursor under the cycle number. Press the +++ or
- - - keys to view other defrost times (cycles) for the day
shown. Place the cursor under the day (SUN) and
press the +++ or - - - keys to access the other days of
the week.
If the Power Saver Mode is OFF, the following screen
will be displayed.
POWER SAVER MODE
OFF
SEL
If a Power Saver Mode is programmed, one of the
following screens will appear. (The model 349 will
display defrost information for freezing cylinders 1, 2,
3, and 4 instead of LEFT and RIGHT.)
DEFROST TIME LEFT
CYCLE 1
SUN
<- - - - - - >
There are seven possible Power Saver Mode time
frames (cycles). The second display line shows the
cycle (1 of 7) as well as the time and day at which the
Power Saver Mode will begin for that cycle. The third
line shows the time and day that the Power Saver
Mode will end for that cycle. Press the +++ or - - - keys
to view other cycles.
Models 345, 346, 349, 355
SEL
The fifth feature will indicate the left side defrost
time(s) and which day(s) the defrost will occur.
B.O.M. 035527C000
S/N K0000000
WITH H20 PRESS SW
POWER SAVER REST
SUN
CYCLE 1
SUN
+++
- - -
01:00
08:30
+++
- - -
09:00
SEL
The sixth feature will indicate the right side defrost
time(s) and which day(s) the defrost will occur.
Note: The functionality is the same as described
previously for the left side defrost.
DEFROST TIME RIGHT
ALL
CYCLE 1
01:00
08:30
SEL
+++
21
- - -
10:00
SEL
Important: To the Operator
DEFROST TIME RIGHT
SUN
CYCLE 1
<- - - - - - >
+++
- - -
The fault description is listed on the third line of the
fault page.
10:00
SEL
FAULT HISTORY
06/25/01
B H2O PRESS LOW
+++ - - -
Press the SEL key to return to the OPERATOR MENU.
Screen F is CURRENT CONDITIONS. This screen
displays the current viscosity and product temperature
for each freezing cylinder. An asterisk will indicate
which side is refrigerating. Press the SEL key to return
to the OPERATOR MENU.
Screen H is SERVICE MENU. This screen allows the
authorized service technician to access service
information. Return to the OPERATOR MENU by
using the arrow keys to move the cursor under the
letter “A”, and press the MENU/SEL key.
The following screen is exemplary of models 345, 346,
and 355. The model 349 displays all four freezing
cylinders.
OPERATOR MENU
ABCDEFGH
SERVICE MENU
<- - - - - - >
Syrup Out Indicator
AUTO
OUT
1
08:34
+++ - - -
CO2- OK
SEL
MODE
SYRUP
AUTO
OK
WATER- OK
If the word “OUT” appears in one of the columns next
to the word “SYRUP”, it indicates a lack of syrup or
syrup pressure being supplied for the indicated
freezing cylinder. If the unit is in the AUTO or PRIME
modes, the product light will flash and a warning tone
will sound for that freezing cylinder. At this time,
replace the appropriate syrup. As a safety feature, the
refrigeration system automatically stops to prevent a
freeze-up in the freezing cylinder.
Press the arrow keys to increase or decrease the
fault page.
Page numbers are located in the upper right hand
corner of the display. The most recently recorded fault
will appear on page 1.
FAULT HISTORY
06/25/01
R SYRUP PRESS LOW
+++ - - -
SEL
27.5F
26.5F
SEL
Screen G is FAULT HISTORY. This option provides
a record of the last 20 faults. The display also indicates
the date and time each fault occurs.
FAULT HISTORY
06/25/01
NO FAULT FOUND
SEL
Press the MENU/SEL key to return to the OPERATOR
MENU.
Note: Viscosity is checked only when product
temperature is below 40_F/4.4_C.
CURRENT CONDITIONS
L*
999HD
R
1200HD
3
08:32
If a syrup out condition occurs on one side, that side
will enter the HOLD mode at which time refrigeration
remains off, the beater continues to run, and the
CO2 solenoid is closed for that side to prevent the
dispensing of product. The opposite side will not be
affected.
2
08:33
SEL
060522
Important: To the Operator
22
Models 345, 346, 349, 355
CO2 Out Indicator
AUTO
OK
MODE
SYRUP
CO2- OUT
Audio Alarm Silencer
The audio alarm will be disabled if the ALARM
SILENCE key is pressed. If a new fault or fault
condition occurs or the system mode changes, the
audio alarm will be re-enabled automatically. If the
audio alarm is silenced for greater than 30 minutes
without correcting the fault, it will be re-enabled
automatically.
AUTO
OK
WATER- OK
On the LCD, if the word “OUT” appears next to the
word “CO2” it indicates a lack of CO2 being supplied to
the freezer. The product light will also flash and a
warning tone will sound. This will continue until the
CO2 is replaced. If the CO2 is not replaced within one
minute, the machine will shut down and a fault
message will appear.
Product Light
When the light is flashing, it indicates that the product
is not at serving viscosity. This will occur during the
initial freeze down, a defrost cycle and a FAULT
condition and during power saver modes.
Water Out Indicator
AUTO
OK
MODE
SYRUP
CO2- OK
Sampling Valve
AUTO
OK
The sampling valve is located behind the front drip tray.
The sampling valve is used to obtain a brix reading.
WATER- OUT
On the LCD, if the word “OUT” appears next to the
word “WATER”, it indicates a lack of water being
supplied to the freezer. In addition, the product light will
flash and a warning tone will sound. This will continue
until the proper amount of water is supplied to the
freezer. If the water is not supplied within one minute,
the machine will shut down and a fault message will
appear.
Models 345, 346, 349, 355
Daily Procedures
The following procedure should be performed daily.
Remove the splash shield, front drip tray and center
drip pan. Take these parts to the sink and brush-clean
them. Re-install the parts onto the freezer.
23
Important: To the Operator
Section 6
Operating Procedures
Assembly
The Models 345, 346 and 355 contain two 7 quart (6.6
liter) freezing cylinders. The Model 349 contains four
7 quart (6.6 liter) freezing cylinders.
MAKE SURE THE CONTROL SWITCH IS IN
THE OFF POSITION. Failure to do so may result in
personal injury or component damage.
CAUTION: This unit is pressurized when
in operation. The control switch, located on the top
side of the control box must be in the OFF position until
the unit is completely assembled. No part should ever
be removed from the machine while it is in operation.
No parts should be removed until the control switch
has been turned to the OFF position and all pressure
has been relieved at the draw handle.
Note: When lubricating parts, use an approved food
grade lubricant (example: Taylor Lube HP).
Step 1
Lubricate the o-ring groove. Slide the o-ring into the
groove on the drive shaft. Lubricate the drive shaft seal
groove, the o-ring, and the shaft portion that comes in
contact with the bearing on the beater drive shaft. DO
NOT lubricate the hex end of the drive shaft.
The syrup flow controls combine the two ingredients of
soda water and syrup, and send this combination to
the mix hoppers. As product is drawn, new product
from the hopper will flow through a mix feed tube down
into the freezing cylinder. The mix hopper is supplied
with 20 pounds of CO2 gas for dispensing the finished
product.
We begin our instructions at the point where the parts
are disassembled and laid out to air dry.
The following procedures will show you how to
assemble the parts into the freezer, sanitize them, and
prime the freezer with fresh product.
Duplicate the following procedures, where they apply,
for the remaining freezing cylinder(s).
Figure 9
Lubricate the inside diameter of the drive shaft seal.
Install the drive shaft seal bushing in the drive shaft
seal.
If you are disassembling the machine for the first time
or need information to get to this starting point in our
instructions, turn to page 36 , “Disassembly” and start
there.
Figure 10
Operating Procedures
24
Models 345, 346, 349, 355
Note: The drive shaft bushing must be positioned in
the center of the drive shaft seal.
Step 2
Install the beater assembly. First check the scraper
blades for any nicks or signs of wear. If any nicks are
present or if the blade is worn, replace both blades. If
the blades are in good condition, place the scraper
blades over the holding pins on the beater.
Slide the seal and bushing over the shaft and groove
until it snaps into place. Fill the inside portion of the
seal with 1/4” more lubricant and evenly lubricate the
end of the seal that fits onto the rear shell bearing.
Note: Each hole on the scraper blade must fit
securely over each pin.
Figure 13
Figure 11
Align the flats on the end of the beater assembly with
the drive shaft. Make sure the beater assembly
locating pin is in position in the locating hole of the drive
shaft. Turn the beater slightly to be certain that the
beater is properly seated. When in position, the beater
will be approximately 3/8” inside the front of the
freezing cylinder.
Insert the beater drive shaft into the freezing cylinder,
hex end first, and into the rear shell bearing until the
seal fits securely over the rear shell bearing. Be certain
the drive shaft fits into the drive coupling without
binding. Remove any excess lubricant from the seal.
Important: Failure to properly seat the beater may
cause damage to the beater and the door.
Figure 12
Models 345, 346, 349, 355
Figure 14
25
Operating Procedures
Note: The scraper blades on the beater assembly
should be in the 6 and 12 o’clock positions. This will
enable freezer door installation.
Figure 17
Snap the draw valve handle onto the door spout. Align
the hole in the draw valve with the slot in the draw
handle.
Figure 15
Step 3
Install the draw valve. Slide the two o-rings into the
grooves on the draw valve. Lubricate the o-rings and
the valve as illustrated below.
Figure 18
Slide the pivot pin through the draw handle and into the
draw valve.
Figure 16
Insert the draw valve into the freezer door spout from
the front of the unit. The valve is properly installed
when the hole in the draw valve is visible in the slot of
the freezer door spout.
Operating Procedures
Figure 19
26
Models 345, 346, 349, 355
Place the draw handle slide over the opening in the
draw handle and the pivot pin. Secure the assembly
with screws.
Step 4
Install the prime plug. Place the two o-rings on the
prime plug and lightly lubricate.
Figure 20
Insert the spring into the front of the door spout.
Figure 23
Step 5
Place the large o-ring into the door groove and lightly
lubricate.
Figure 21
Place the threaded cap on the end of the draw valve
cavity. Turn the cap clockwise until it is secure.
Figure 24
Note: Every three months, discard the o-rings and
install new o-rings.
Figure 22
Models 345, 346, 349, 355
27
Operating Procedures
Step 6
Install the front bearing. Do not lubricate the front
bearing.
Figure 27
Install the hopper cover. Lock it into place.
Figure 25
Step 7
Install the freezer door. Position the door on the four
studs on the front of the freezing cylinder. Firmly push
the door into place. Install the four handscrews on the
studs and finger-tighten them equally in a criss-cross
pattern to insure that the door is snug. Do not
over-tighten the handscrews.
Figure 28
Attach the vinyl tube to the pressure relief on the
hopper cover. Position the open end of the vinyl tube
into the rear drip pan.
Figure 26
Figure 29
Repeat Steps 1 through 8 for the remaining freezing
cylinder(s).
Step 8
Place the o-ring into the groove of the hopper cover.
Operating Procedures
28
Models 345, 346, 349, 355
Step 9
Install the center drip pan through the front of the
machine.
Step 2
Prepare two gallons (7.6 liters) of an approved 100
PPM sanitizing solution (example: Kay-5R). USE
WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS. IMPORTANT: Make sure
the sanitizer is completely dissolved.
If your freezer uses Bag in Box syrup, follow steps 3
through 5. If your freezer uses syrup tanks, follow the
instructions on page 5.
Step 3
Bag in Box Units Only: Using an empty bag of syrup,
cut the syrup line connection from the end of the bag.
Figure 30
Sanitizing
Note: If a unit is sanitized, and will not be used for an
extended period of time, clean water should be used
to flush all sanitizer from the lines prior to storage of the
unit. Upon return to service, the unit must be sanitized
prior to use.
Figure 32
Step 1
Open the lighted display door. Remove the hood and
the side panels to gain access to the hoppers. Place
the control switch in the ON position.
Step 4
Connect the syrup line to the syrup connection that
was cut from the syrup bag.
Figure 31
Figure 33
Models 345, 346, 349, 355
29
Operating Procedures
Step 5
With the bag connector attached to the syrup line,
place the syrup line into the pail of sanitizing solution.
Figure 36
Step 7
Place a mix pail beneath the sampling valve which is
located behind the front drip tray. Slowly open the
sampling valve and allow sanitizer to flow through this
line and into the pail. After approximately 1/2 gallon of
sanitizer has been dispensed, close the valve.
Step 8
Raise the prime plug only enough to allow a slight
hissing sound. Place an empty pail under the door
spout. When sanitizing solution begins to exit the relief
port opening in the freezer door, lower the prime plug.
Press the OFF key.
Figure 34
Replace Steps 3 - 5 for Syrup Tank Units: Pour the
solution into a clean, empty syrup tank. Place the
syrup tank cover in position. Remove the CO2 line and
syrup line number one from the syrup tank for freezing
cylinder number one. Connect these lines to the spare
syrup tank filled with sanitizing solution.
Figure 37
Figure 35
Step 9
Prepare two gallons (7.6 liters) of an approved 100
PPM sanitizing solution (example: Kay-5R). USE
WARM WATER AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS.
Step 6
Press the PRIME key. This will cause the sanitizing
solution to flow through the lines and into the mix
hopper.
Operating Procedures
30
Models 345, 346, 349, 355
Step 10
With the pail beneath the door spout, open the draw
valve and relieve all pressure from the freezing
cylinder. Remove the hopper cover. Slowly pour the
two gallons (7.6 liters) of sanitizing solution into the mix
hopper until the hopper becomes 1/4 full of sanitizing
solution.
Figure 40
Figure 38
Step 11
With the brushes provided, brush-clean the mix
hopper, mix inlet hole, mix level float switch, product
fitting, CO2 fitting and mix feed tube. Use caution when
cleaning the float switch so as not to damage it.
Figure 41
Figure 39
Models 345, 346, 349, 355
Figure 42
31
Operating Procedures
Step 14
Press the BEATER key. Agitate the solution in the
freezing cylinder for five minutes.
Figure 43
Step 12
Install the mix feed tube into the mix inlet hole in the
bottom of the mix hopper.
Figure 46
Step 15
With a pail beneath the door spout, open the draw
valve and drain all the solution from the mix hopper and
the freezing cylinder. Press the OFF key and close the
draw valve.
Figure 44
Step 13
Sanitize and install the hopper cover. Lock the cover
into place. Attach the vinyl tube to the pressure relief
valve on the hopper cover. Position the open end of the
vinyl tube into the rear drip pan.
Figure 47
Step 16
Disconnect the syrup connector in the sanitizing
solution.
Repeat Steps 2 through 14 for the remaining freezing
cylinder(s).
Step 17
Remove the right side panel and install the rear white
drip pan.
Figure 45
Operating Procedures
32
Models 345, 346, 349, 355
Priming/Brixing
Step 3
Raise the prime plug enough to allow a slight hissing
sound.
Step 1
Connect the syrup line to the syrup tank (or the Bag in
Box).
Step 2
Press the BEATER key to pressurize the freezing
cylinder.
Figure 50
Note: The pressure in the freezing cylinder should be
relieved very slowly.
Step 4
Slowly open the syrup sampling valve and let it run into
a bucket until all the sanitizer is removed and full
strength product is flowing. Do not open the valve so
much that the syrup line to the hopper is drained.
Figure 48
After three minutes, press the PRIME key. This will
cause the product to flow to the mix hopper.
Figure 51
Brix is the ratio of syrup to water which will directly
affect the quality and taste of the product. Brixing
should be done before priming the freezer and when
a change in syrup flavor has been made.
Figure 49
Models 345, 346, 349, 355
33
Operating Procedures
Allow the product to flow over the refractometer. The
brix reading should register 13 to 14. A reading higher
than this would cause a darker, richer product. The
refrigeration system would have to run longer to freeze
this excess syrup. A reading lower than this could
cause a freeze-up in the freezing cylinder because of
the excess water.
Figure 54
Step 6
With a pail beneath the door spout, press the BEATER
key. Open the draw valve and drain the freezing
cylinder. Close the draw valve. After three minutes,
press the PRIME key. This will cause the product to
flow to the mix hopper.
Step 7
Hold a large cup under the pressure relief port exit of
the door, until the liquid level (not foam) reaches the
pressure relief port. Lower the prime plug. Press the
OFF key.
Figure 52
To adjust the brix, turn the adjustment screw located
in the service panel. Clockwise adjustments increase
the amount of syrup to water, and counterclockwise
adjustments decrease the amount of syrup to water.
Adjust the screw in small increments and check the
brix again.
Note: A large amount of foam indicates that the prime
plug was raised too high.
Repeat Steps 1 through 7 for the remaining freezing
cylinder(s).
Step 8
To place the freezing cylinder in the AUTO mode,
press the AUTO key. When the unit cycles off, the
product will be at serving viscosity.
Figure 53
Repeat this step until a correct brix reading is
registered.
Step 5
Once the proper brix has been achieved, close the
sampling valve. Install the front drip tray and the splash
shield on the front of the freezer.
Operating Procedures
Figure 55
Repeat this step for the remaining freezing
cylinder(s).
34
Models 345, 346, 349, 355
Step 2
When all the product has been drained from the mix
hopper and the freezing cylinder, close the draw valve
and press the OFF key. Discard this product.
Step 9
Replace the side panels and close the lighted display.
Install the hood in position on top of the freezer.
90 Day Closing Procedure
We recommend that the machine be completely
disassembled and cleaned at least every ninety days
using the following procedures.
ALWAYS FOLLOW LOCAL HEALTH CODES
Figure 57
To disassemble a freezer, the following items will be
needed:
S
S
S
S
Repeat Steps 1 and 2 for the remaining freezing
cylinder(s).
Two cleaning pails
Necessary brushes (provided with freezer)
Cleaner
Single service towels
Cleaning
Step 1
Open the lighted display door from the front of the
machine. Remove the hood and side panels to gain
access to the hoppers.
Draining Product From the
Freezing Cylinder
Step 2
Prepare two gallons (7.6 liters) of an approved cleaning solution (example: Kay-5R). USE WARM WATER
AND FOLLOW THE MANUFACTURER’S SPECIFICATIONS.
Step 1
Press the BEATER key. This will allow the beater to
operate and CO2 pressure will be maintained to push
the product from the freezing cylinder. Open the draw
valve and drain the product from the machine until the
CO2 begins to jet.
Important: Make sure the cleaner is completely
dissolved.
Step 3
Pour the solution into a clean, empty bucket. Place the
syrup line with old syrup connection into the bucket of
sanitizer.
Step 4
Press the PRIME key. This will cause the cleaning
solution to flow through the lines and into the mix
hopper.
Step 5
Remove the front drip tray. Place a mix pail beneath
the sampling valve located behind the front drip tray.
Slowly open the sampling valve and allow cleaner to
flow through this line and out into the pail. After
approximately 1/2 gallon of cleaner has been
dispensed, close the valve.
Figure 56
Models 345, 346, 349, 355
35
Operating Procedures
Disassembly
Step 6
Raise the prime plug. Place an empty pail under the
door spout. When cleaning solution begins to exit the
relief port opening in the freezer door, lower the prime
plug. Press the OFF key. Open the draw valve and
relieve all pressure from the freezing cylinder. Remove
the hopper cover. Remove the mix feed tube and take
it to the sink for further cleaning. Close the prime plug.
Step 1
Be sure the control switch is in the OFF position. Open
the draw valves to make sure all pressure has been
relieved.
Step 2
Raise the prime plug. Leave the bleed port open when
removing the freezer door to insure that all pressure is
relieved from the freezing cylinder.
Step 7
Prepare two gallons (7.6 liters) of an approved
cleaning solution (example: Kay-5R). USE WARM
WATER AND FOLLOW THE MANUFACTURER’S
SPECIFICATIONS.
Step 3
Remove the following parts from the freezer and take
them to the sink for brush-cleaning: handscrews,
freezer doors, beater assemblies and scraper blades,
drive shafts, hopper covers, front drip tray, splash
shield.
Step 8
Slowly pour two gallons (7.6 liters) of cleaning solution
into the mix hopper until the hopper becomes 1/4 full
of cleaning solution.
Brush Cleaning
Step 1
Prepare a sink with an approved cleaning solution.
USE WARM WATER AND FOLLOW THE
MANUFACTURER’S SPECIFICATIONS (example:
Kay-5R). IMPORTANT: Follow the label directions.
Too STRONG of a solution can cause parts damage,
while too MILD of a solution will not provide adequate
cleaning. Make sure all brushes provided with the
freezer are available for brush cleaning.
Step 9
With the brushes provided, brush-clean the mix
hopper, mix inlet hole, mix level float switch, product
fitting, and CO2 fitting. Use caution when cleaning the
float switch. Failure to do so will cause damage to the
component.
Step 2
Return to the freezer with a small amount of cleaning
solution. With a single service towel, wipe clean the
bearing surface. Brush-clean the rear shell bearings at
the back of the freezing cylinders with the black bristle
brush.
Step 10
Clean and install the hopper cover. Lock the cover into
place. Attach the vinyl tube to the pressure relief valve
on the hopper cover. Position the open end of the vinyl
tube into the rear drip pan.
Step 11
Press the BEATER key to agitate the solution in the
freezing cylinder.
Step 12
With a pail beneath the door spout, open the draw
valve and drain all the solution from the mix hopper and
the freezing cylinder. Press the OFF key and close the
draw valve.
Step 13
Disconnect the syrup connector.
Figure 58
Step 3
Remove the rear drip pan. (Does not apply to the
Model 349.)
Repeat Steps 2 through 13 for the remaining freezing
cylinder(s).
Operating Procedures
36
Models 345, 346, 349, 355
Note: To remove o-rings, use a single service towel to
grasp the o-ring. Apply pressure in an upward direction
until the o-ring pops out of its groove. With the other
hand, push the top of the o-ring forward. It will roll out
of the groove and can be easily removed. If there is
more than one o-ring to be removed, always remove
the rear o-ring first. This will allow the o-ring to slide
over the forward rings without falling into the open
grooves.
Step 4
Remove the right side panel and take the rear, white
drip pan to the sink for further cleaning.
Step 5
Remove the following parts: seals and o-rings from the
drive shafts, drive shaft seal bushings from drive shaft
seals, caps and springs from freezer doors, screws
and draw handle slides from freezer doors, pivot pins
from draw valves, draw valve handles from freezer
doors, draw valves from freezer doors, o-rings from
draw valves, prime plugs from freezer doors, o-rings
from prime plugs, o-rings and front bearings from
freezer doors, o-rings from mix hopper covers.
Step 6
Using a single service towel, wipe the lubricant off the
parts. Brush-clean all disassembled parts in the
cleaning solution. Make sure all lubricant and syrup is
removed. Place all the cleaned parts on a clean, dry
surface to air-dry.
Step 7
Wipe clean all the exterior surfaces of the freezer.
Discard all o-rings and replace them with new ones.
Models 345, 346, 349, 355
37
Operating Procedures
Section 7
Important: Operator Checklist
During Cleaning and Sanitizing
j 7. Clean and sanitize the syrup lines regularly to
prevent syrup residue build-up that would
restrict the proper flow of syrup.
j 8. On a regular basis, take a brix reading to assure
a consistent quality product.
ALWAYS FOLLOW LOCAL HEALTH CODES
Cleaning and sanitizing schedules are governed by
your State or local regulatory agencies and must be
followed accordingly. The following check points
should be stressed during the cleaning and sanitizing
operations.
Regular Maintenance Checks
WE RECOMMEND CLEANING AND SANITIZING
EVERY 90 DAYS.
Troubleshooting Bacterial Count
j 1. Replace scraper blades that are nicked,
damaged or worn down.
j 1. Thoroughly clean and sanitize the machine
regularly, including complete disassembly and
brush cleaning.
j 2. Before installing the beater, be certain that the
scraper blades are properly attached over the
pins.
j 2. Use all brushes supplied for thorough cleaning.
The brushes are specially designed to reach all
product passageways.
j 3. Check the rear shell bearing for signs of wear
(excessive product leakage from the rear drip
pans to the front drip tray).
j 3. Use the white bristle brush to clean the mix inlet
hole which extends from the mix hopper down
to the rear of the freezing cylinder.
j 4. Dispose of o-rings or seals if they are worn, torn,
or fit too loosely, and replace with new ones.
j 4. Use the black bristle brush to thoroughly clean
the rear shell bearing located at the rear of the
freezing cylinder. Be sure there is a generous
amount of cleaning solution on the brush.
j 5. Follow all lubricating procedures as outlined in
“Assembly”.
j 5. Using a screwdriver and a cloth towel, keep the
rear shell bearing and the female hex drive
socket clean and free of lubricant and product
deposits.
j 6. Check the condenser(s) for accumulation of dirt
and lint. Dirty condensers will reduce the
efficiency and capacity of the machine.
Condensers should be cleaned monthly by
removing the poly- flo filter and cleaning it.
Remove the service panel and side panels to
expose the condenser(s).
Never use
screwdrivers or other metal probes to clean
between the fins.
j 6. Properly prepare the cleaning and sanitizing
solutions. Read and follow the label directions
carefully. Too strong of a solution may damage
the parts and too weak of a solution will not do
an adequate job of cleaning or sanitizing.
Important: Operator Checklist
38
Models 345, 346, 349, 355
Winter Storage
If the place of business is to be closed during the winter
months, it is important to protect the freezer by
following certain precautions, particularly if the
building is subject to freezing conditions.
Wrap detachable parts of the freezer such as the
beater, the scraper blades, the drive shaft, and the
freezer door. Place these parts in a protected, dry
place. Rubber trim parts and gaskets can be protected
by wrapping them with moisture-proof paper. All parts
should be thoroughly cleaned of dried mix or
lubrication which attract mice and other vermin.
Disconnect the freezer from the main power source to
prevent possible electrical damage.
Note: It is recommended that an authorized service
technician perform winter storage draining, to insure
all water has been removed. This will guard against
freezing and rupturing of the components.
Your local Taylor Distributor can perform this service
for you.
Models 345, 346, 349, 355
39
Important: Operator Checklist
Section 8
PROBLEM
1. Product is too stiff.
Troubleshooting Guide
PROBABLE CAUSE
REMEDY
PAGE
REF.
a. Too much water to syrup
ratio. Improper brix
adjustment.
a. Adjust the brix
accordingly.
b. Consistency control needs
adjustment.
b. Contact a service
technician.
- - -
c. Torque coupling bound in
WARM position.
c. Contact a service
technician.
- - -
a. Freezer in a defrost cycle.
a. Wait for defrost cycle to
end.
- - -
b. Consistency control needs
adjustment.
b. Contact a service
technician.
- - -
c. Torque coupling bound in
COLD position.
c. Contact a service
technician.
- - -
d. Broken springs in torque
coupling.
d. Contact a service
technician.
- - -
3. No product is being
dispensed.
a. Product frozen-up in
freezing cylinder.
a. See problem No. 1.
- - -
4. Freezer will not operate in
the BEATER or AUTO
mode.
a. Unit is unplugged.
a. Check the plug at wall
receptacle.
- - -
b. Blown fuse, or the circuit
breaker is off.
b. Replace the fuse or turn
the breaker on.
- - -
c. Beater motor is out on
overload. Check fault
description screen.
c. Allow the motor to cool.
Press the AUTO key. Call
a service technician if the
beater motor goes out on
overload again.
18
a. Beater motor is out on
overload. Check the fault
description screen.
a. Allow the motor to cool.
Press the AUTO key. Call
a service technician if the
beater motor goes out on
overload again.
18
b. The torque coupling is
bound in the COLD
position.
b. Contact a service
technician.
c. Condenser dirty, A/C.
c. Clean condenser monthly.
d. Water supply off, W/C.
d. Turn the water on.
2. Product is too soft.
5. No compressor operation
in the AUTO mode.
Troubleshooting Guide
40
33
- - -
38
- - -
Models 345, 346, 349, 355
PROBLEM
PROBABLE CAUSE
REMEDY
PAGE
REF.
a. Rounded corners of hex
end of drive shaft, drive
coupling, or both.
a. Replace the drive shaft, or
call a service technician to
replace the direct drive
unit.
- - -
b. Lubrication of hex end of
drive shaft.
b. Do not lubricate the hex
end. If necessary, contact
a service technician for
removal.
24
7. Excessive loss of CO2.
a. Leak in the CO2 system.
a. Contact a service
technician.
8. Leakage from rear drip
pan(s) into front drip tray.
a. Seal or o-ring on drive
shaft is worn, missing, or
incorrectly installed.
a. Replace or install correctly
on drive shaft.
24
b. Worn rear shell bearing.
b. Contact a service
technician to replace rear
shell bearing.
- - -
a. Inadequate lubrication of
draw valve o-rings.
a. Lubricate properly.
26
b. Wrong type lubricant on
draw valve o-rings.
b. Use food grade lubricant
(example: Taylor Lube
HP).
24
c. Worn or missing draw
valve o-rings.
c. Replace or install o-rings
on draw valve.
26/ 42
a. Syrup lines need to be
cleaned and sanitized.
a. Clean and sanitize syrup
lines.
- - -
b. Blocked flow control.
b. Contact a service
technician.
- - -
a. Loss of CO2 to propel
syrup.
a. Contact a service
technician.
- - -
b. Clogged or kinked syrup
lines.
b. Sanitize syrup lines
regularly. If kinked, repair
or replace.
- - -
a. Machine is not in the
AUTO or PRIME mode.
a. Place the machine in the
AUTO or PRIME mode.
34
b. The mix level float switch
is inoperative.
b. Contact a service
technician.
- - -
a. Faulty check valve in
carbonation system.
a. Call a service technician
to replace the check
valve.
- - -
6. Unable to remove the
drive shaft from the rear
shell bearing.
9. Excessive mix leakage
from door spout.
10. Unable to adjust brix.
11. Lack of syrup being
supplied to machine.
12. Product does not enter
mix hopper.
13. Carbonated water or
sulfuric aroma is evident
in the faucet or sewage
system.
Models 345, 346, 349, 355
41
- - -
Troubleshooting Guide
Section 9
PART DESCRIPTION
Parts Replacement Schedule
EVERY 3 MONTHS
EVERY 6 MONTHS
ANNUALLY
X
Minimum
Black Bristle Brush, 1” x 2”
Inspect & Replace if
Necessary
Minimum
Double Ended Brush
Inspect & Replace if
Necessary
Minimum
White Bristle Brush, 1-1/2” x 2”
Inspect & Replace if
Necessary
Minimum
White Bristle Brush, 3” x 7”
Inspect & Replace if
Necessary
Minimum
Scraper Blade
Drive Shaft Seal
X
Drive Shaft O-Ring
X
Freezer Door O-Ring
X
Draw Valve O-Ring
X
Door Spout O-Ring
X
Hopper Cover O-Ring
X
Front Bearing
X
Prime Plug O-Ring
X
Refer to Parts List on the next page when ordering the above parts.
Parts Replacement Schedule
42
Models 345, 346, 349, 355
Section 10 Limited Warranty on Equipment
TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS
Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited
warranty on new Taylor-branded freezer equipment available from Taylor to the market generally (the “Product”)
to the original purchaser only.
LIMITED WARRANTY
Taylor warrants the Product against failure due to defect in materials or workmanship under normal use and
service as follows. All warranty periods begin on the date of original Product installation. If a part fails due to
defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service agency,
will provide a new or re- manufactured part, at Taylor’s option, to replace the failed defective part at no charge for
the part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited warranty for
a Product failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions listed
below and on the reverse (if any) of this document.
Product
Soft Serve
Frozen Yogurt
Shakes
Smoothies
Frozen Beverage
Batch Desserts
Part
Limited Warranty Period
Insulated shell assembly
Five (5) years
Refrigeration compressor
(except service valve)
Five (5) years
Beater motors
Two (2) years
Beater drive gear
Two (2) years
Printed circuit boards and
Softech controls beginning
with serial number H8024200
Two (2) years
Parts not otherwise listed in
this table or excluded below
One (1) year
LIMITED WARRANTY CONDITIONS
1.
If the date of original installation of the Product cannot be verified, then the limited warranty period begins
ninety (90) days from the date of Product manufacture (as indicated by the Product serial number). Proof of
purchase may be required at time of service.
2.
This limited warranty is valid only if the Product is installed and all required service work on the Product is
performed by an authorized Taylor distributor or service agency, and only if genuine, new Taylor parts are
used.
3.
Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in
the Taylor Operator’s Manual.
4.
Defective parts must be returned to the authorized Taylor distributor or service agency for credit.
5.
The use of any refrigerant other than that specified on the Product’s data label will void this limited warranty.
LIMITED WARRANTY EXCEPTIONS
This limited warranty does not cover:
1.
Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of
defective parts, replacement parts, or new Products.
2.
Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning
of condensers.
131122
Models 345, 346, 349, 355
43
Limited Warranty on Equipment
3.
Replacement of wear items designated as Class “000” parts in the Taylor Operator’s Manual.
4.
External hoses, electrical power supplies, and machine grounding.
5.
Parts not supplied or designated by Taylor, or damages resulting from their use.
6.
Return trips or waiting time required because a service technician is prevented from beginning warranty
service work promptly upon arrival.
7.
Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing,
unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including
but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning
supplies.
8.
Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake
or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty,
accident or condition beyond the reasonable control of Taylor; operation above or below the electrical or
water supply specification of the Product; or components repaired or altered in any way so as, in the
judgment of the Manufacturer, to adversely affect performance, or normal wear or deterioration.
9.
Any Product purchased over the Internet.
10.
Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the
inadequacy or interruption of electrical service.
11.
Electricity or fuel costs, or increases in electricity or fuel costs from any reason whatsoever.
12.
Damages resulting from the use of any refrigerant other than that specified on the Product’s data label will
void this limited warranty.
13.
Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.
14.
ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY
NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential
damages, so this limitation may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from
jurisdiction to jurisdiction.
LIMITATION OF WARRANTY
THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS
AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER’S SOLE
REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE
COMPONENTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL
OR INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS,
PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS
WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED
BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.
LEGAL REMEDIES
The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or
complaint with the Product, stating the defect or complaint and a specific request for repair, replacement, or other
correction of the Product under warranty, mailed at least thirty (30) days before pursuing any legal rights or
remedies.
Taylor Company
a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072
Limited Warranty on Equipment
44
Models 345, 346, 349, 355
Section 11
Limited Warranty on Parts
TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS
Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited
warranty on new Taylor genuine replacement components and parts available from Taylor to the market generally
(the “Parts”) to the original purchaser only.
LIMITED WARRANTY
Taylor warrants the Parts against failure due to defect in materials or workmanship under normal use and service
as follows. All warranty periods begin on the date of original installation of the Part in the Taylor unit. If a Part fails
due to defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service
agency, will provide a new or re- manufactured Part, at Taylor’s option, to replace the failed defective Part at no
charge for the Part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited
warranty for a Part failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions
listed below and on the reverse (if any) of this document.
Limited Warranty Period
Part’s Warranty Class Code or Part
Class 103 Parts¹
Three (3) months
Class 212 Parts²
Twelve (12) months
Class 512 Parts
Twelve (12) months
Class 000 Parts
No warranty
Taylor Part #072454 (Motor- 24VDC *C832/C842*)
Four (4) years
LIMITED WARRANTY CONDITIONS
1.
If the date of original installation of the Part cannot be otherwise verified, proof of purchase may be required
at time of service.
2.
This limited warranty is valid only if the Part is installed and all required service work in connection with the
Part is performed by an authorized Taylor distributor or service agency.
3.
The limited warranty applies only to Parts remaining in use by their original owner at their original installation
location in the unit of original installation.
4.
Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in
the Taylor Operator’s Manual.
5.
Defective Parts must be returned to the authorized Taylor distributor or service agency for credit.
6.
This warranty is not intended to shorten the length of any warranty coverage provided pursuant to a separate
Taylor Limited Warranty on freezer or grill equipment.
7.
The use of any refrigerant other than that specified for the unit in which the Part is installed will void this
limited warranty.
1, 2
Except that Taylor Part #032129SER2 (Compressor-Air-230V SERV) and Taylor Part #075506SER1
(Compressor-Air-115V 60HZ) shall have a limited warranty period of twelve (12) months when used in Taylor
freezer equipment and a limited warranty period of two (2) years when used in Taylor grill equipment.
131122
Models 345, 346, 349, 355
45
Limited Warranty on Parts
LIMITED WARRANTY EXCEPTIONS
This limited warranty does not cover:
1.
Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of
defective Parts, replacement Parts, or new Parts.
2.
Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning
of condensers or carbon and grease buildup.
3.
Required service, whether cleaning or general repairs, to return the cooking surface assemblies, including
the upper platen and lower plate, to an operational condition to achieve proper cooking or allow proper
assembly of release sheets and clips as a result of grease build-up on the cooking surfaces, including but
not limited to the platen and plate, sides of the shroud or top of the shroud.
4.
Replacement of cooking surfaces, including the upper platen and lower plate, due to pitting or corrosion (or
in the case of the upper platen, due to loss of plating) as a result of damage due to the impact of spatulas or
other small wares used during the cooking process or as a result of the use of cleaners, cleaning materials
or cleaning processes not approved for use by Taylor.
5.
Replacement of wear items designated as Class “000” Parts in the Taylor Operator’s Manual, as well as any
release sheets and clips for the Product’s upper platen assembly.
6.
External hoses, electrical power supplies, and machine grounding.
7.
Parts not supplied or designated by Taylor, or damages resulting from their use.
8.
Return trips or waiting time required because a service technician is prevented from beginning warranty
service work promptly upon arrival.
9.
Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing,
unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including
but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning
supplies.
10.
Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake
or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty,
accident or condition beyond the reasonable control of Taylor; operation above or below the gas, electrical or
water supply specification of the unit in which a part is installed; or Parts or the units in which they are
installed repaired or altered in any way so as, in the judgment of Taylor, to adversely affect performance, or
normal wear or deterioration.
11.
Any Part purchased over the Internet.
12.
Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the
inadequacy or interruption of electrical service.
13.
Electricity, gas or other fuel costs, or increases in electricity or fuel costs from any reason whatsoever.
14.
Damages resulting from the use of any refrigerant other than that specified for the unit in which the Part is
installed will void this limited warranty.
15.
Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.
16.
ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY
NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential
damages, so this limitation may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from
jurisdiction to jurisdiction.
Limited Warranty on Parts
46
Models 345, 346, 349, 355
LIMITATION OF WARRANTY
THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS
AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER’S SOLE
REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE
PARTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL OR
INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS,
PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS
WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED
BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.
LEGAL REMEDIES
The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or
complaint with the Part, stating the defect or complaint and a specific request for repair, replacement, or other
correction of the Part under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.
Taylor Company
a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072
Models 345, 346, 349, 355
47
Limited Warranty on Parts
Parts List
032511
Bearing- Rear Shell
48
041182
Beater Assembly
X30160
046536-
Housing A.- W/Wheel
Motor- Blower
X47833-
Blower Assembly
033047
053726
Wheel- Blower
Capacitor- Run
053729
Screen- Blower
X53725- 27
Blower A.
053481- 27
039422
Block- Terminal 2P- L1,L2
053728
039422
Block- Terminal 2P- L1,L2
Motor- Fan 208- 230V 50/60 HZ
033145
Belt (Rear Bearing Units)
Housing- Blower- 6 POLE
044056
Belt
053720
033142
Belt
Clip- Screen- Blower
025633
Belt
041103
X39163- SER
Bearing- Unit Rear (2 Pulley)
+Blade- Scraper
X39162- SER
Bearing- Unit Rear (1 Pulley)
012864
X49506
Accumulator A.- Insulated
+Washer- Bearing Lock
053377
Accumulator- Copper 2”DIA 13”LG
018432
X50468
Accumulator A.- Insulated- Right
+O- Ring
X50465
Accumulator A.- Insulated- Left
028991
X50139
Accumulator A.- Insulated- Right
028992
X50138
Accumulator A.- Insulated- Left
+Nut- Brass Bearing
047062
Accumulator- Copper 2” Dia. 10” Long
+Guide- Drip Seal
042134
X50261
PART
NUMBER
+Accumulator- Suction- Vertical
Accumulator A.- Insulated
DESCRIPTION
1
1
2
4
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
4
1
2
2
2
4
2
2
2
2
2
2
2
1
1
2
1
1
1
1
1
1
1
1
4
1
3
1
2
2
8
4
2
2
4
4
4
4
4
1
1
2
1
1
1
4
2
1
1
2
2
2
2
2
1
1
345
346
349
355
QTY. QTY. QTY. QTY.
103
103
103
103
103
103
103
103
103
103
103
103
000
000
000
000
000
103
103
103
000
000
000
000
000
103
103
103
103
103
103
103
103
103
WARR.
CLASS
Prior to: 346- K0066159, 349- K0053129
346- K0066159/Up, 349- K0053129/Up
Prior to: 349- J9097086, 355- J8113767
349- J9097086/Up, 355- J8113767
Kit- Includes Retaining Plate- 052131
Kit- Includes Retaining Plate- 052131
Prior to J9053838
0355- J9053838/Up
Prior to J9114879
Prior to J9114879
Prior to J9072433
Prior to J9072433
345- J9067375/Up, 346- J9072433/Up,
349- J9114879/Up
Prior to J9067375
Prior to J9067375
REMARKS
126
129
144
144
144
PARTS
UPDATE
Section 12
Parts List
+ Available Separately
Models 345, 346, 349 & 355
+ Available Separately
Models 345, 346, 349 & 355
49
Parts List
014753
023316
040040- 010
040040- 011
040040- 042
040040- 043
040040- 041
040040- 015
040040- 019
049455- 27
Brush- White Bristle
Brush- White Bristle (3” x 7”)
Cable- Ribbon- 50C (5”)
Cable- Ribbon- 50C (20”)
Cable- Ribbon- 20C (18”)
Cable- Ribbon- 20C (18”)
Cable- Ribbon- 20C (14”)
Cable- Ribbon- 14C (14”)
Cable- Ribbon- 14C (22”)
Carbonator
032571
+Lock- Caster Bracket
052401- 27
+Relay- Compressor
037430
+Relay- Start- Compressor
029439
048134
+Capacitor- Run - 35MFD/375V
+Capacitor- Start - 124- 147MFD/330V
047520-
031790
+Capacitor- Start - 161- 193UF/250V
Compressor (TECUMSEH)
037431
+Capacitor- Run - 25UF/440V
036880-
053106
+Capacitor- Start 189- 227UF/250V
Compressor (BRISTOL)
029439
+Capacitor- Run 35UF/370V
052396-
030307
Caster- Locking Swivel (Front)
Compressor (COPELAND)
035324
Card- Flavor (Packet of 9 Cards)
021279
043957
Card- FCB P.O.P.
Caster- Swivel (Rear)
032569
Carbonator (OLD)
050257- 27
013072
Probe A.- Carbonator w/Reed Switch
013071
Brush- Double Ended
PART
NUMBER
Brush- Black Bristle (1” x 2”)
DESCRIPTION
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
345
QTY.
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
346
QTY.
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
349 355
QTY. QTY.
103
103
512
103
103
103
512
103
103
103
512
103
103
103
000
000
103
103
103
103
103
103
103
103
103
103
000
000
000
000
WARR.
CLASS
230- 60- 1
230- 60- 1
Replacement for 036880-
230- 60- 1
230- 60- 1
230- 60- 1
355 - For Service - Use X53905- 27
(Modifications Required - SB 2507)
Prior to: 345- J9067375, 346- J9067641,
349- J9097086, 355- J9053838.
For Service- Use 047520- & the
applicable start components.
230- 60- 1
230- 60- 1
230- 60- 1
349- J9097086/Up
345- J9067375/Up 346- J9067641/Up
Jo Bell - Prior to J5061557
230- 60- 1
McCann - J5061557/Up
REMARKS
150
140/141
144
144
144
144
95
103, 119
95, 119
PARTS
UPDATE
+ Available Separately
Parts List
50
Models 345, 346, 349 & 355
020944- 24
039365
039416
043636- L
052898
Tube- Vinyl Drain
Valve- Pressure Relief
Decal- Cleaning Instructions
Decal- Left Control
Decal- Left Control
016037
042079
Cover- Hopper
O- Ring- Hopper Cover
042610
Clamp- Hose
X42080
Cover A.- Mix Tank- Relief Valve
049285- RED
Label- Identification- Red
053290
039734
Spring - Red
Cover- Compressor
039455
Screw- Shoulder
052816
025376
Screw- Set
Cover- Compressor
039453
Pin- Coupling Torque
X39523
Coupling A.- Torque
039397
053376
Condenser A/C
046866
019558
Condenser A/C
Coupling- Load Torque
052502- 2
Condenser- AC- 12LX18HX3.12T 5RW
Coupling- Drive Torque
053502- 1
+Capacitor- Run - 20UF/440V
Condenser- AC- 12LX18HX3.12T 5RW
012906
051957- 27
+Relay- Start- Compressor
INCLUDES:
033044- 1
X53292- 27
051958-
048150
PART
NUMBER
+Capacitor- Start - 189- 227UF/330V
+Box A.- Cap/Relay
Compressor (COPELAND)
+Relay- Start- Compressor
DESCRIPTION
1
1
1
2
2
2
2
2
2
1
2
6
6
4
6
2
2
2
1
1
345
QTY.
1
1
1
2
2
2
2
2
2
2
6
6
4
6
2
2
2
2
1
1
2
346
QTY.
1
4
4
4
4
4
4
2
4
12
12
8
12
4
4
4
2
1
1
2
1
1
1
2
2
2
2
2
2
1
2
6
6
4
6
2
2
2
1
1
1
1
1
1
349 355
QTY. QTY.
000
000
000
103
000
000
103
000
103
103
103
000
103
000
000
103
103
103
103
103
103
103
103
103
103
103
103
512
103
WARR.
CLASS
345- J9053838/Up, 346- J9072433/Up,
355- J9012316/Up
Prior to: 345- J9053838 346- J9072433,
355- J9012316
Bulk under R30335
Sound Barrier - J9053838/Up
Sound Barrier - J9067375/Up
Replaces 047083
Prior to: 346- J9072433 349- J9097086
Front- Right Shell 346- J9072433/Up
349- J9097086/Up
Rear- Left Shell 346- J9072433/Up
349- J9097086/Up
230- 60- 1
230- 60- 1
230- 60- 1
230- 60- 1 - J9053838/UP
J9053838/Up - HP62 Also replacement for
036880- Must convert to HP62 Refrigerant
& install 049154 Dryer. See Update 142
230- 60- 1
REMARKS
142
142
144
139
142
142
PARTS
UPDATE
+ Available Separately
Models 345, 346, 349 & 355
51
Parts List
045967
043892
053646
043467
042941
039463
038374
046586
X53549
X53593
053515044939053566
044940053636043502S052840044107X38062- SER
Decal- Decorative
Decal- Decorative ”Taylor Crown/Logo”
Decal- Dec- Slush- Press- 4 BRL
Decal- Decorative
Decal- Power Switch
Decal- Pressure Gauge (Set of 4)
Decal- Troubleshooting
Deflector- Blower Exhaust
Deflector A.- Air Exhaust *346*
Deflector A.- Air Exhaust *349*
Diagram- Wiring
Diagram- Wiring
Diagram- Wiring *346*
Diagram- Wiring
Diagram- Wiring *349*
Diagram- Wiring
Diagram- Wiring
Diagram- Wiring
Display- Liquid Crystal
046190
046193- BLA
+Slide- Draw Handle
046190- BLA
053869
+Screw
+Spout- Door
017003
+O- Ring
+Spout- Door
046192
+Handle- Draw Valve
046193
046192- BLA
+Handle- Draw Valve
+Slide- Draw Handle
039349
039573
+Bearing- Front
Door- Freezer
038221
053761
+Lens- Display
043636- R
Decal- Dec- Taylor Domed
PART
NUMBER
Decal- Right Control
DESCRIPTION
2
2
4
4
4
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
345
QTY.
2
2
4
4
4
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
346
QTY.
4
4
8
8
8
4
4
4
4
4
1
1
1
1
1
1
1
2
1
1
1
1
2
2
4
4
4
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
349 355
QTY. QTY.
103
103
103
103
000
000
103
103
000
103
103
103
000
000
000
000
000
000
000
103
103
103
000
000
000
000
000
000
000
000
000
WARR.
CLASS
Prior to J8060000
J8060000/Up
Prior to J8060000
J8060000/Up
Prior to J8060000
J8060000/Up
Prior to J9053838
355- J8113767/Up
Prior to J9114233
J9114233/Up
Prior to J9072433
J9072433/Up
Prior to J9067375
J9067375/Up
J9071741/Up
J9072433/Up
Prior to: 346- J9072433, 346- J9071741
Prior to J9114233
349- J6114233/Up
Prior to J8060000
(Dec Plate- X44115- BLA) J8060000 to:
345- K0012597, 346- K0024873
349- K0025070, 355- K0013505
349- K0025070/Up, 355- K0013505/Up
345- K0012597/Up, 346- K0024873/Up,
REMARKS
130
130
151
130
142
144
144
130
PARTS
UPDATE
+ Available Separately
Parts List
52
Models 345, 346, 349 & 355
052779- 1
Filter- Air- 18.00LX16.50HX.70W
043638
Regulator (0 - 100 PSI)
2
+Body A.- Flow Control - Less Solenoid
X48729- SER
2
2
2
1
1
1
1
1
1
1
1
1
1
4
2
2
2
4
2
2
2
345
QTY.
(Or X48729- SER - Body A.- Flow Control
w/o Solenoid)
X48729- 27
043638
Regulator (0 - 100 PSI)
Body A.- Flow Control w/Solenoid
043643
Gauge- Pressure (0 - 100 PSI)
X48728- 27
018466
Fitting 3/8 x 1/4
Flow Control - w/o Pressure Switch
029235
Filter- Water Line
X42151
043643
Filter A.- Regulator
018466
Gauge- Pressure (0 - 100 PSI)
X35019
Filter A.- Regulator
Fitting 3/8 x 1/4
044734
Filter- Water (Carbonator)
029235
053697
Filter- Water 1/4FFLINX1/4MFLOV
Filter- Water Line
040140- 001
Filter- Corcom
053801
049154
Dryer- Filter
+Cover- Hole- Filter- Snap In
045866
016369
+O- Ring
048901
039324
+Valve- Draw
Dryer- Filter
039320
+Spring
Dryer- Filter- HP62- 3/8 X 1/4S
039321
+Pin- Pivot
046138
039219
+O- Ring
Dryer- Filter
039323
+Nut- Spout
049154
046191
Dryer- Filter
046191- BLA
+Cap
PART
NUMBER
+Cap
DESCRIPTION
2
2
2
2
1
1
1
1
1
1
1
1
2
2
2
2
4
2
2
2
4
2
2
2
346
QTY.
4
4
4
4
1
1
1
1
1
1
1
1
2
2
2
2
8
4
4
4
8
4
4
4
2
2
2
1
1
1
4
2
2
2
4
2
2
2
349 355
QTY. QTY.
103
103
103
103
103
103
103
000
103
103
103
103
000
103
000
000
103
000
000
000
000
000
000
000
000
103
103
103
000
103
103
103
WARR.
CLASS
Less Pressure Switch
Prior to J9114233
Prior to: 345- J9067375, 346- J9067641
Prior to: 345- J9102846, 346- J9102432,
349- J9102424
345- J9102846/Up, 346- J9102432/Up
349- J9102424/Up
346- J9072433/Up, 349- J9097086/Up
349- J9097086/Up, 355- J9012316/Up
Prior to J9067641
346- J9067641/Up
Prior to: 345- J8124526, 349- J90097086,
355- J9012316
J8124526/Up
Prior to J8060000
J8060000/Up
REMARKS
144
142
144
144
130
PARTS
UPDATE
+ Available Separately
Models 345, 346, 349 & 355
53
Parts List
051826- 155
051826- 168
018520
018521
030386
018595
Hose- Beverage
Hose- Beverage
Marker- No. 1
Marker- No. 2
Valve- Check
Washer- Nylon Flare
016715
018520
018521
018522
018523
Adaptor- Swivel
Marker- No. 1
Marker- No. 2
Marker- No. 3
Marker- No. 4
X52457
051826- 146
Hose- Beverage
Harness A.- Feed
049427
X49312
Harness A.- Feed
Fitting
X47137
Guide A.- Drip Pan
052140
X47134
Ferrule
045606
+Holder- Fuse
Guide A.- Drip Pan
044519
045293
Fuse 15 Amp - In Line
Label- CO2
016137
+O- Ring- Plug
016715
1
049573
+Plug- Pressure Switch
Adaptor- Swivel
1
049706
+Switch- Pressure 15 PSI
2
2
2
2
1
1
1
2
6
2
4
1
1
2
2
2
2
048784
4
30
+Switch- Pressure 35 PSI
048709
Screw- 8 x 1/2 SL Hex
2
041951
048829
Retainer- Inlet Line
4
4
2
30
2
4
345
QTY.
Screw- 8- 32 x 3/8 Hex
016137
X48732
Bowl A.- Float- Flow Control
O- Ring- Flow Control Float A.
048709
Screw- 8 x 1/2 SL Hex
048710
048829
Clip- Retainer- Syrup Pressure Switch
048776- 27
Retainer- Inlet Line
PART
NUMBER
Coil- Solenoid
DESCRIPTION
2
2
2
2
1
1
1
2
6
2
4
1
1
1
1
2
2
4
2
4
12
2
4
2
2
24
2
4
346
QTY.
2
2
2
2
6
1
2
2
4
4
4
4
8
24
4
8
4
4
48
4
8
1
1
1
2
2
2
2
4
12
2
4
2
2
24
2
4
349 355
QTY. QTY.
000
000
000
000
103
103
000
103
000
000
000
000
000
103
000
000
103
103
103
103
103
000
000
103
103
103
000
000
103
000
103
103
000
103
103
WARR.
CLASS
J8050000/Up (Replaces X49313)
Bulk - R30313
Bulk - R30313
Bulk - R30313
non- pressurized units only
non- pressurized units only
non- pressurized units only
REMARKS
130
128
PARTS
UPDATE
+ Available Separately
Parts List
54
Models 345, 346, 349 & 355
030386
051826- 180
051826- 210
044519
049427
Valve- Check
Hose- Beverage
Hose- Beverage
Label- CO2
Fitting
045199
049428
021030
051826- 120
051826- 188
051826- 8
018520
018521
018522
018523
019762
030386
049429
018595
Decal- Soda
Elbow
Ferrule
Hose- Beverage
Hose- Beverage
Hose- Beverage
Marker- No. 1
Marker- No. 2
Marker- No. 3
Marker- No. 4
Tee
Valve- Check
Valve- Check
Washer- Nylon Flare
039349
039219
016369
025307
017003
016037
029751
048260- WHT
O- Ring (Door Spout)
O- Ring (Draw Valve)
O- Ring (Drive Shaft)
O- Ring (Freezer Door)
O- Ring (Hopper Cover)
O- Ring (Prime Plug)
O- Ring Removal Tool
X39699
Kit A.- Tune- Up
Bearing- Front
042166
Hood
044618
016715
Adaptor- Swivel
Hood
018646
Adaptor
X51823
052140
Harness A.- Feed
018595
Ferrule
PART
NUMBER
Washer- Nylon Flare
DESCRIPTION
1
4
2
2
2
4
4
2
2
1
345
QTY.
2
4
2
2
2
4
4
2
2
1
346
QTY.
4
8
4
4
4
8
8
4
4
1
4
2
1
4
4
10
4
2
4
2
2
2
4
4
2
2
1
4
2
2
1
2
2
3
3
2
2
3
14
2
3
8
1
1
349 355
QTY. QTY.
000
000
000
000
000
000
000
000
000
103
103
000
103
103
103
000
000
000
000
000
000
000
000
103
000
103
103
103
103
000
000
000
103
000
000
WARR.
CLASS
Bulk - R30313
Bulk - R30313
REMARKS
128
128
PARTS
UPDATE
+ Available Separately
Models 345, 346, 349 & 355
55
Parts List
051433
042279
039462
051807
036397
Label- Warning- Cover
Label- Warning- Do Not Draw Product
Label- Warning- Relieve Pressure
LED Assembly (Product Not Ready)
Leg- 4”
016715
052140
051826- 65
Adaptor- Swivel
Ferrule
Hose- Beverage
052140
051826- 24
Ferrule
Hose- Beverage
051826- 50
Hose- Beverage
051826- 8
Hose- Beverage
2
051826- 9
016715
052140
018520
Ferrule
Marker- No. 1
X52453
4
2
2
4
4
2
1
2
2
2
1
1
1
2
2
7
1
2
345
QTY.
052140
Adaptor- SWV 1/4F 1/4Barb*SS*
Line A.- CO2 (No. 1)
Hose- Beverage
Ferrule
X43656
052140
Ferrule
Line A.- CO2 (Right & Left) (OLD)
016715
Adaptor- Swivel
X53880
052140
Ferrule
Line A.- CO2 (Right & Left) (NEW)
016715
Adaptor- Swivel
X44518
044519
Label- CO2
Line A.- CO2 (Regulator to Carbonator)
016715
Adaptor- Swivel
X44952
X28150
Line A.- Air Supply
Line A.- CO2 (Regulator to Carbonator)
051751
Lens- Yellow
039268
032749
Label- Door- Warning- Moving Parts
+Cap- Rubber
032164
032560
PART
NUMBER
Label- Caution- GRD- PERM- ENG/SP
Seal (Drive Shaft)
DESCRIPTION
2
4
2
2
4
4
2
1
2
2
2
1
2
1
2
2
8
1
1
2
346
QTY.
2
2
2
1
1
2
2
1
4
2
2
2
7
1
1
4
2
4
2
2
4
4
2
1
2
2
1
2
4
4
1
2
2
5
1
1
2
349 355
QTY. QTY.
000
000
103
103
000
000
103
000
000
103
103
000
000
103
103
000
000
000
103
103
000
000
103
103
103
000
103
103
000
000
000
000
000
000
WARR.
CLASS
J8050000/Up (Replaces X45182)
Bulk - R30313
Use w/Old Style 2.5 Quart Mix Tank
Bulk- R30313
Use w/New Style 3.5 Quart Mix Tank
Bulk - R30313
Bulk - R30313
Bulk - R30313
LED Snap In - Replaces 042509- LensRed
New Amber Light (Replaces X42508)
To Prevent Injury 349- 4 prior to J8124111
w/Light Flashing 349- 4 prior to J8124111
Replaces 036529 Decal
*CAUTION*
346- J9084947/Up, 349- J9097086/Up,
355- J9012316/Up
REMARKS
130
128
151
151
128
128
128
136
PARTS
UPDATE
+ Available Separately
Parts List
56
Models 345, 346, 349 & 355
018521
051826- 27
Marker- No. 2
Hose- Beverage
018522
051826- 28
Marker- No. 3
Hose- Beverage
018523
051826- 29
Marker- No. 4
Hose- Beverage
051826- 36
Hose- Beverage
051826- 3
051826- 32
051826- 40
051826- 42
018520
019762
031622
Hose- Beverage
Hose- Beverage
Hose- Beverage
Hose- Beverage
Marker- No. 1
Tee- 1/4 Barb- SS
Valve- Sampling
X49667
052140
Ferrule
Line A.- Mix Outlet (Left & Right)
049428
020563
Elbow- 3/8 O- Ring x 1/4 Barb
Elbow- 1/4 FFL x 1/4 Barb
X49585
051826- 36
Hose- Beverage
Line A.- Mix Outlet (Left)
052140
Ferrule
X41005
052140
Ferrule
Line A.- CO2- BIB Pump
016715
Adaptor- Swivel
X31565
052140
Ferrule
Line A.- CO2 (CO2 Tank to Syrup Tank)
016715
Adaptor- SWV 1/4F 1/4Barb*SS*
X52456
052140
Ferrule
Line A.- CO2 (No. 4)
016715
Adaptor- SWV 1/4F 1/4Barb*SS*
X52455
052140
Ferrule
Line A.- CO2 (No. 3)
016715
X52454
051826- 30
PART
NUMBER
Adaptor- SWV 1/4F 1/4Barb*SS*
Line A.- CO2 (No. 2)
Hose- Beverage
DESCRIPTION
1
1
2
1
1
1
1
4
1
1
1
2
2
2
2
4
4
2
345
QTY.
1
1
2
1
1
1
1
6
1
1
1
2
2
2
2
4
4
2
346
QTY.
4
8
8
4
1
2
2
2
1
1
2
2
2
1
1
2
2
2
1
1
2
2
4
4
2
349 355
QTY. QTY.
103
103
103
000
000
000
000
000
000
103
103
103
000
000
103
000
000
103
103
000
000
000
103
103
000
000
000
103
103
000
000
000
103
103
000
WARR.
CLASS
Use w/New Style 3.5 Quart Mix Tank
Use w/Old Style 2.5 Quart Mix Tank
Bulk - R30313
Bulk - R30313
Bulk - R30313
Bulk - R30313
Bulk - R30313 (Replaces 051826- 4)
J8050000/Up (Replaces X45185)
Bulk - R30313 (Replaces 051826- 8)
J8050000/Up (Replaces X45184)
Bulk - R30313 (Replaces 051826- 9)
J8050000/Up (Replaces X45183)
Bulk - R30313 (Replaces 051826- 14)
REMARKS
151
151
128
128
128/130
130
128/130
130
128/130
130
128/130
PARTS
UPDATE
+ Available Separately
Models 345, 346, 349 & 355
57
Parts List
051826- 42
051826- 40
018521
019762
031622
Hose- Beverage
Hose- Beverage
Marker- No. 2
Tee- 1/4 Barb SS
Valve- Sampling
052140
051826- 5
051826- 38
051826- 36
051826- 48
018520
019762
031622
Ferrule
Hose- Beverage
Hose- Beverage
Hose- Beverage
Hose- Beverage
Marker- No. 1
Tee
Valve- Sampling
020563
049428
052140
051826- 3
051826- 5
Elbow- 1/4 FFL x 1/4 Barb
Elbow- 3/8 O- Ring x 1/4 Barb
Ferrule
Hose- Beverage
Hose- Beverage- 1/4 ID X 7/16 OD
X49720
049428
Elbow- 3/8 O- Ring x 1/4 Barb
Line A.- Mix Outlet (No. 2)
020563
Elbow- 1/4 FFL x 1/4 Barb
X49719
051826- 32
Hose- Beverage
Line A.- Mix Outlet (No. 1)
051826- 3
X49586
Line A.- Mix Outlet (Right)
Hose- Beverage
031622
Valve- Sampling
052140
051826- 40
Hose- Beverage
Ferrule
051826- 46
Hose- Beverage
049428
051826- 24
Hose- Beverage
Elbow- 3/8 O- Ring x 1/4 Barb SS
052140
Ferrule
020563
049668
Elbow- 1/4 FFL x 1/4 Barb Swivel
020563
Elbow- 3/8 O- Ring x 1/4 Barb
PART
NUMBER
Elbow- 1/4 FFL x 1/4 Barb
DESCRIPTION
1
1
2
1
1
1
1
6
1
1
1
345
QTY.
1
1
2
1
1
1
1
6
1
1
1
346
QTY.
1
1
6
1
1
1
1
1
2
1
1
1
1
6
1
1
1
2
2
2
2
8
2
2
349 355
QTY. QTY.
000
000
000
103
103
103
103
103
000
000
000
000
000
000
103
103
103
103
103
000
000
000
000
000
000
103
103
103
103
000
000
000
000
103
103
WARR.
CLASS
Use w/New Style 3.5 Quart Mix Tank
Use w/Old Style 2.5 Quart Mix Tank
Use w/Old Style 2.5 Quart Mix Tank
Use w/New Style 3.5 Quart Mix Tank
Use w/Old Style 2.5 Quart Mix Tank
Use w/New Style 3.5 Quart Mix Tank
Use w/Old Style 2.5 Quart Mix Tank
Use w/New Style 3.5 Quart Mix Tank
REMARKS
151
151
151
151
PARTS
UPDATE
+ Available Separately
Parts List
58
Models 345, 346, 349 & 355
018521
019762
031622
Marker- No. 2
Tee- 1/4 Barb SS
Valve- Sampling
052140
051826- 5
051826- 48
051826- 50
018522
019762
031622
Ferrule
Hose- Beverage
Hose- Beverage
Hose- Beverage
Marker- No. 3
Tee
Valve- Sampling
051826- 38
051826- 36
051826- 48
018523
019762
Hose- Beverage
Hose- Beverage
Hose- Beverage
Marker No. 4
Tee
052140
051826- 63
Ferrule
Hose- Beverage
016715
045199
052140
Adaptor- Swivel
Decal- Soda
Ferrule
X49587
016715
Adaptor- Swivel
Line A.- Soda (Carbonator- Sentry)
018646
Adaptor- Barb
X44961
051826- 5
Hose- Beverage
Line A.- Pressure (Water)
052140
Ferrule
031622
049428
Elbow- 3/8 O- Ring x 1/4 Barb
Valve- Sampling
020563
Elbow- 1/4 FFL x 1/4 Barb
X49722
049428
Elbow- 3/8 O- Ring x 1/4 Barb
Line A.- Mix Outlet (No. 4)
020563
Elbow- 1/4 FFL x 1/4 Barb
X49721
051826- 50
Line A.- Mix Outlet (No. 3)
051826- 48
Hose- Beverage
PART
NUMBER
Hose- Beverage
DESCRIPTION
6
3
3
1
1
2
1
1
1
345
QTY.
6
3
3
1
1
2
1
1
1
346
QTY.
1
1
2
1
1
1
1
6
1
1
1
1
1
2
2
1
1
6
1
1
1
1
1
1
2
1
349 355
QTY. QTY.
000
000
103
103
000
000
103
103
103
103
103
000
000
000
000
000
000
103
103
103
103
103
000
000
000
000
000
103
103
103
103
103
000
000
000
WARR.
CLASS
Prior to: 345- J9067375, 346- J9056262
Use w/Old Style 2.5 Quart Mix Tank
Use w/New Style 3.5 Quart Mix Tank
Use w/New Style 3.5 Quart Mix Tank
Use w/Old Style 2.5 Quart Mix Tank
Use w/New Style 3.5 Quart Mix Tank
Use w/Old Style 2.5 Quart Mix Tank
REMARKS
144
151
151
151
151
151
151
PARTS
UPDATE
+ Available Separately
Models 345, 346, 349 & 355
59
Parts List
019762
049429
018595
Tee
Valve- Check
Washer- Nylon
020565- 28
Hose- Beverage
020565- 24
Tube- Nylobrade
020568- 86
Tube- Nylobrade
020565- 20
Tube- Nylobrade
053503
020565- 3
020565- 38
020565- 50
051729
038582
Fitting- 3/8MFL x 3/8 Barb
Hose- Beverage
Tube- Nylobrade
Hose- Beverage
Regulator- Water 30 PSI Fixed
Tee- 3/8 Barb x 1/4MFL x 3/8 Barb
019194
029834
053503
020565- 16
Adaptor- SWV 3/8F X 3/8arb*SS*
Ferrule- .650 ID NP Brass
Fitting- 3/8MFL X 3/8Barb- Brass
Hose- Beverage- 3/8 ID X 5/8 OD
X53645
029834
Ferrule
Line A.- Water *349*REG.
019194
Adaptor- Swivel- 3/8F x 3/8 Barb
X53386
029834
Ferrule
Line A.- Water- Regulator
019194
Adaptor
X42219
029834
Ferrule
Line A.- Water (Pump Inlet)
019194
Adaptor
X44953
029834
Ferrule
Line A.- Water (Pump Inlet)
049464
Elbow
X49465
029834
Ferrule
Line A.- Water (Pump Discharge)
049464
Elbow
X49485
051826- 30
Line A.- Water (Pump Discharge)
051826- 28
Hose- Beverage
PART
NUMBER
Hose- Beverage
DESCRIPTION
1
1
1
1
1
1
6
1
1
1
2
2
1
1
2
2
1
2
2
1
2
1
345
QTY.
1
1
1
1
1
1
6
1
1
1
2
2
1
1
2
2
1
2
2
1
2
1
346
QTY.
1
1
6
1
1
1
2
2
1
1
2
2
1
349 355
QTY. QTY.
000
103
000
103
103
103
103
000
000
000
103
000
103
103
000
000
103
103
000
000
103
103
000
000
103
103
000
000
103
103
000
103
103
000
000
WARR.
CLASS
Bulk R30333
J9114233/Up
Bulk R30333
Bulk R30333
Bulk R30333
345- J9067375/Up, 346- J9067641/Up
Prior to J9102424
Prior to: 345- J9067375, 346- J9055262
Bulk - R30333
REMARKS
144
144
PARTS
UPDATE
+ Available Separately
Parts List
60
Models 345, 346, 349 & 355
051835- 4
051835- 3
051835- 2
051835- 1
Regulator- 60 PSI
Regulator- 20 PSI
Coil- Service- CO2 Manifold
+ Kit- Service- Valve & Coil
051835- 4
051835- 3
Regulator- 60 PSI
Regulator- 20 PSI
051835- 2
027875
Coil- Service- CO2 Manifold
Gauge- 60PSI- 1/8 MPT- Back Mount
051833- 27
X51832- 27
Manifold A.- CO2 - 1 Regulator - 2 Solenoid
Manifold- CO2- 1 Regulator - 2 Solenoids
051839- 27
Manifold- CO2- 2 Regulator - 4 Solenoid
005139
044534
Valve- Check- 1/4MPT In X 1/4MFL Out
Elbow- 1/4MFL X 1/8MPT Brass
044534
Valve- Check 1/4MPTINX1/4MFLOUT
051835- 1
052699
Gauge- 100 PSI- Back Mount
+ Kit- Service- Valve & Coil
027875
Gauge- 60 PSI- Back Mount
051839- 27
Manifold- CO2- 2Reg/4Sol*349*
051835- 2
001485
Fitting- 1/4MFL X 1/8MPT
Coil- Service- CO2 Manifold
005139
X51838- 27
Elbow- 1/4MFL X 1/8MPT Brass
Manifold A.- CO2 - 2 Regulator- 4 Solenoid
044534
052699
Gauge- 100 PSI - 1/8 MPT- Back Mount
Valve- Check - 1/4MPT In X 1/4MFL Out
027875
051835- 27
Manifold- CO2 - 2 Regulator - 2 Solenoid
Gauge- 60 PSI - 1/8 MPT- Back Mount
005139
Elbow- 1/4MFL X 1/8MPT Brass
X51834- 27
038582
Tee- 3/8 BARBX1/4MFLX3/8BARB- SS
Manifold A.- CO2 - 2 Regulators - 2 Solenoids
051729
Regulator- Water- 30 PSI Fixed
048232
020565- 8
Lubricant- Taylor
020565- 38
Hose- Beverage- 3/8 ID X 5/8 OD
PART
NUMBER
Hose- Beverage- 3/8 ID X 5/8 OD
DESCRIPTION
2
2
2
1
1
1
1
1
3
1
1
345
QTY.
2
2
2
1
1
1
1
1
3
1
1
346
QTY.
1
4
4
4
1
1
1
1
4
1
1
2
1
1
1
1
1
1
1
2
1
2
1
1
349 355
QTY. QTY.
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
000
103
103
000
000
WARR.
CLASS
J8040000/Up
Includes: Plunger Tube, Nut, Coil &
Bracket, Spring, Plunger & O- Ring
J8054096/Up (Repl X47223- 27 Sol)
Includes: Plunger Tube, Nut, Coil &
Bracket, Spring, Plunger & O- Ring
J8040000/Up
Bulk R30333
Bulk R30333
REMARKS
136
136
129
136
136
136
129
136
136
136
136
128
PARTS
UPDATE
+ Available Separately
Models 345, 346, 349 & 355
61
Parts List
042352
018595
Valve- Check
Washer- Flare Nylon
016309043666
013163
044949
Nut- Stud
Pail (10 qt. - 9.5 liter)
Pan- Drip (Expansion Valve)
019624
+Capacitor- Run - 4UF- 370V
Motor- Pump
047060
+Blade- Fan (12” Push)
041401-
051785
Motor- Fan - 120 Watt
047279
+Capacitor- Run - 4UF- 440V
051744-
049009
+Blade- Fan (12” Push)
Motor- Fan - 80 Watt
+Blade- Fan (12” Push)
029770-
019624
+Capacitor- Run - 4UF- 370V
Motor- Fan - 50 Watt
047061
041401-
53419
+Blade- Fan (12” Pull)
Motor- Fan - 120 Watt
+Blade- Fan (12” Pull)
029770-
X42342
Manifold A.- Soda
Motor- Fan 50 Watt
051826- 26
Hose- Beverage
033140-
051826- 23
Hose- Beverage
Motor- Beater
051826- 19
Hose- Beverage
014477-
049427
Fitting- 3/8 O- Ring x 1/4 Barb SS
Motor- Beater
052140
Ferrule
039710- M
020130
Adaptor- 1/8 MP x 1/4 Barb
Man- Oper 345/346/349/355
016715
X49718
Adaptor- Swivel
Manifold A.- Soda w/Check Valve
044534
051835- 1
Valve- Check - 1/4MPT In X 1/4MFL Out
051835- 3
Regulator- 20 PSI
PART
NUMBER
+ Kit- Service- Valve & Coil
DESCRIPTION
1
1
8
1
1
1
1
1
1
2
1
345
QTY.
1
1
8
1
2
1
346
QTY.
1
16
1
2
1
4
4
1
2
2
1
4
10
1
5
1
1
8
1
1
1
1
1
1
1
1
1
1
2
2
1
349 355
QTY. QTY.
103
000
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
212
212
000
000
103
103
000
000
000
103
000
103
103
103
103
103
103
WARR.
CLASS
Prior to J8010000
Fan Motor (208- 230/60/1)
J8010000 thru J9053837
J9053838/Up
J9053838/Up
Fan Motor - Prior to J9067375
Prior to J9067375
Prior to J9067375
J9067375/Up
J9067375/Up
Includes: Plunger Tube, Nut, Coil &
Bracket, Spring, Plunger & O- Ring
REMARKS
142
142
144
144
144
144
144
136
136
PARTS
UPDATE
+ Available Separately
Parts List
62
Models 345, 346, 349 & 355
043599
042082- BLA
042082- WHT
043599SBLA
Panel- Front Lower
Panel- Front- Lower
Panel- Front Lower
Panel- Front Lower
X45136
X44917
X42289
044619- SP
X53611
X44919
Panel A.- Left Side
Panel A.- Left Side
Panel- Left Side
Panel A.- Side *346*AC*R*Filter
Panel A.- Right Side
044916
Panel- Service
Panel A.- Left Side
044621- SS
Panel- Rear
042293
X42197
Panel A.- Rear
Panel- Service
042198
Panel- Rear *349*Drain Hole*
053652
044921- SP1
Panel- Rear
Panel- Service *349*AC*
042081- WHT
Panel- Front Upper
045125
042081- BLA
Panel- Front Upper
Panel- Service
043600
Panel- Front Upper
053612
043600- BLA
Panel- Front Upper
Panel- Service *346* Filter
043599- SP
Panel- Front Lower
049775
043599- BLA
Panel- Front Lower
+Plug- Hole- 1/2- Black
X50226
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
020944- 11
Tube- Vinyl Drain
Pan A.- Drip (Expansion Valve)
1
1
1
020944- 11
Tube- Vinyl Drain
1
1
X42204
X42202
Pan A.- Left Drip
1
1
1
1
1
1
1
2
1
1
1
349 355
QTY. QTY.
X42203
X42201
Pan A.- Drip w/Hose (Left)
1
1
346
QTY.
Pan A.- Right Drip
043612
345
QTY.
Pan A.- Drip w/Hose (Right)
035034
Pan- Rear White Drip
PART
NUMBER
Pan- Long Black Drip 19- 1/2 in Long
DESCRIPTION
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
000
103
103
103
103
103
103
000
103
103
000
103
103
103
103
WARR.
CLASS
Water cooled and A/C prior to J9072433
Air cooled only - J9072433/Up
Water cooled and A/C Prior to J9114233
Air cooled only J9114233/Up
Water cooled and A/C prior to J9072433
Air cooled only - J9072433/Up
Prior to J9114240
J9114240/Up
Prior to J8110000
J8110000/Up
Prior To J8060000
J8060000/Up, 355J9024482/Up
Prior to J8060000
J8060000/UP
Prior to J8110000
J8110000/Up
Prior to J8060000
J8060000/Up
Rear Shell Bearing
Rear Shell Beariing
Rear Shell Bearing
Rear Shell Bearing
Drip Guide
Rear Shell Bearing
REMARKS
130
130
130
PARTS
UPDATE
+ Available Separately
Models 345, 346, 349 & 355
63
Parts List
X47299- SER
X53580- SER
PCB A.- Brown Out
PCB A.- Control *345* UVC2 (CURRENT)
X40875
X40876
Chip- Software UVC2 U10 English
Chip- Software UVC2 U11
X40875
X40876
Chip- Software UVC2 U10 English
Chip- Software UVC2 U11
040176- 006
X45315- SER
PCB A.- Control (OLD STYLE)
X40876
Chip- Software UVC2 U11
IC- Parallel Port Chip
X40875
Chip- Software UVC2 U10 English
X40791
X40873
Chip- Software UVC2 Chip- SEL
Chip- Software
X40872
X51169- SER
Chip- Software UVC2 Display
PCB A.- Universal (Base Board)
X53653- SER
X40838
PCB A.- Control (CURRENT)
X44863- SER
Chip- Software
X47233- SER
PCB A.- Universal (Base Board)
PCB A.- Control (OLD STYLE)
X40789
X40873
Chip- Software UVC2 Chip- SEL
Chip- Software
X40872
X51169- SER
PCB A.- Universal (Base Board)
Chip- Software UVC2 Display
X53517- SER
X40837
Chip- Software/Old
PCB A.- Control *346*UVC2 (CURRENT)
X44863- SER
PCB A.- Universal (Base Board/Old)
X47235- SER
X40878
Chip- Software (Old)
PCB A.- Control (OLD STYLE)
X51169- SER
X52440- SER
PCB A.- UVC2 (Base Board)
PCB A.- Control *345* UVC2 (OLD STYLE)
X40790
X40873
Chip- Software UVC2 Chip- SEL
Chip- Software
X40872
Chip- Software UVC2 Display
X51169- SER
044620- SP
PCB A.- UVCA (Base Board)
X42291
Panel- Right Side
PART
NUMBER
Panel A.- Right Side
DESCRIPTION
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
345
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
346
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
349 355
QTY. QTY.
212
103
103
103
103
103
103
212
212
103
212
212
103
103
103
103
103
212
212
103
212
212
103
212
212
103
103
103
103
103
212
212
103
103
103
WARR.
CLASS
Use X53653- SER
J9114233/Up
J9114233/Up
J9114233/Up
Prior to J9067641
Prior to J9067641
Use X53517- SER
J9067641/Up
J9067641/Up
J9067641/Up
Prior to J8072717
Prior to J8072717
Use X52440- SER
J8072717 thru J9067374
J8072717/UP
J8072717 thru J9067374
J9067375/Up
J9067375/Up
REMARKS
148
148
148
148
145
145
145
145
145
145
132
132
132
132
132
132/144
144
PARTS
UPDATE
+ Available Separately
Parts List
64
Models 345, 346, 349 & 355
X40781
X44115
Plate A.- Decorative
038061- BLK
025570
035955
047094
047095
027616
042190
016306
Probe- Thermistor (Barrel)
Pulley- 11” Dia. (Rear Bearing Unit)
Pulley- 11” Dia.
Pulley (Rear Bearing Unit)
Pulley (Rear Bearing Unit)
Pulley (Beater Motor)
Pulley (Beater Motor)
Pump- Water
+O- Ring
1
1
1
2
2
2
4
X44115- BLA
Plate A.- Decorative
1
029751
043639- BLA
Plate- Dec- 345- 346- 355*BLACK
2
035410
Plate- Decorative (Cover w/Slots for Flavor
Cards)
1
039568
035410- BLA
Plate- Decorative
Plug- Prime
X45622- SER
X40839
Chip- Software
PCB A.- Interface
X44863- SER
PCB A.- Universal (Base Board)
X47234- SER
X40877
Chip- Software
PCB A.- Control (OLD STYLE)
X51169- SER
PCB A.- UVC2 (Base Board)
X52439- SER
1
X40876
Chip- Software UVC2 U11
Chip- Software- 355- 355A UVC2
PCB A.- Control *355*UVC2 (OLD STYLE)
1
X40875
Chip- Software UVC2 U10 English
1
X40873
1
X40872
Chip- Software UVC2 Chip- SEL
X51169- SER
345
QTY.
Chip- Software UVC2 Display
PCB A.- UVC2 (Base Board)
X52846- SER
X40833
PCB A.- Control *355- 355A UVC2*(CURRENT)
X44863- SER
Chip- Software
PART
NUMBER
PCB A.- Universal (Base Board)
DESCRIPTION
1
2
2
2
4
2
1
1
1
1
1
1
1
1
346
QTY.
2
2
2
2
4
8
4
1
1
2
1
1
1
1
1
1
1
1
1
1
2
4
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
349 355
QTY. QTY.
103
103
103
103
103
103
103
103
000
103
103
103
103
103
103
212
103
212
212
103
212
212
103
103
103
103
103
212
212
103
212
WARR.
CLASS
Prior to J8060000
346- J9113331, 355- J9024482
J8060000 to: 345- J9125292,
345- J9125292/Up, 346- J9113331/Up,
355- J9024482/Up
Prior to J8110000 (White)
J8110000/Up
Prior to J8072560
Prior to J8072560
Use X52439- SER
J8072560 thru J9053837
J8072560/Up
(Replaces X47234- SER)
Use Prior to J9053838
J9053838/Up
J8072560/Up
J9053838/Up
Prior to J9114233
Prior to J9114233
REMARKS
130
132
132
132
132/142
132
132/142
142
142
PARTS
UPDATE
+ Available Separately
Models 345, 346, 349 & 355
65
Parts List
051840
X53756
X44905
X53812
X43624
043719
Shell A.- Insulated (OLD)
Shell A.- Insulated (NEW)
Shell A.- Insulated (OLD)
Shield- Splash
020945- 96
X38355
Shell A.- Insulated (NEW)
+Tube- Vinyl
Shelf A.- Drip Tray
020945- 96
X44898
Shelf A.- Drip Tray
+Tube- Vinyl
044403
049697
+Screw- Thumb
Shelf- Drip Tray
032560
039337
Shaft- Beater Drive
+Seal
X47221- 4
Sensor A.- Viscosity No. 4
025307
X47221- 3
Sensor A.- Viscosity No. 3
+O- Ring
X47221- 2
Sensor A.- Viscosity No. 2
042278
X47221- 1
Sensor A.- Viscosity No. 1
+Bushing- Drive Shaft Seal
X44951
051840- 22R
Ring- Quad- Hose- Regulator- CO2
Sensor A.- EVC
051840- 22
Hose- Regulator- 3 Foot- Hi Pressure
041082
051840- 16
Gauge- Regulator- 3000 lb.
012725-
051840- 15
Gauge- Regulator- 160 lb.
Sanitizer- Kay 5
051840- 7
Seat Assembly
Relay- Compressor
051840- 6
Diaphragm
Includes:
042791
Regulator- CO2 (Wall Mount)
PART
NUMBER
Pump- Water
DESCRIPTION
1
2
2
1
1
2
2
2
2
2
1
1
1
1
1
2
1
1
1
345
QTY.
1
2
2
1
1
2
2
2
2
2
1
2
1
1
1
2
1
1
1
346
QTY.
4
4
1
1
4
4
4
4
1
1
1
1
1
2
1
1
1
2
1
1
1
1
1
2
2
2
1
2
2
2
2
2
1
1
1
1
1
2
1
1
1
349 355
QTY. QTY.
103
512
512
512
512
000
103
000
103
000
103
000
000
103
103
103
103
103
103
103
000
103
000
103
103
103
000
103
103
103
WARR.
CLASS
Shell, X53880 CO2 Line & 053875- 5 or - 8
Feed Tube
Prior to K0038353 Replace With X53812
3.5 Quart Mix Tank k0038353/Up
Prior to Above Serial Numbers - replace
with X53756 Shell, 053875- 5 or - 8 Feed
tube. 345 & 346 also use X53880 CO2
Line.
345- K0026349/Up, 346- K0024873/Up,
349- K0025070/Up
Includes Fittings
Replaces 031623
REMARKS
151
151
124, 126
PARTS
UPDATE
+ Available Separately
Parts List
66
Models 345, 346, 349 & 355
043720
053875- 5
039566- 5
020945- 96
044455
047016
043232
053565
046365
050900
027137
047053
Tray- Front Drip
Tube- Mix Feed (NEW)
Tube- Mix Feed (OLD)
Tube- Vinyl (Drip Tray Shelf- Drain Line)
Valve- Access (Compressor)
Valve- Access (Compressor)
Valve- Access (Compressor)
Valve- Access- 1/4MFL X 3/8ODSDR
Valve- Automatic Expansion
+Boot- Expansion Valve
+Boot- Expansion Valve
Valve- Check (Defrost Line)
X44936
Switch A.- Float- Mix Level
038275- SP
038065
Switch- Membrane
043720- SP
053138
Switch- Membrane - 23” - Right
Tray- Front Drip
044521
Switch- Membrane - 20” - Left
Tray- Front Drip
036070
Switch- Low Pressure Switch (CO2)
045754
016292
Switch- Low Pressure Switch (H2O)
Transformer
046362
Switch- Pressure - 440 PSI
012626
048230
Switch- Pressure - 440 PSI
Switch- Toggle- SPST 3/4 HP 250V
036265
020445
+Washer- Freezer Stud
038276
Stud- Nose Cone (Freezing Cylinder)
PART
NUMBER
Shield- Splash
DESCRIPTION
2
2
2
2
1
1
1
2
2
1
1
1
2
2
1
1
1
1
1
1
8
8
345
QTY.
2
2
2
2
2
1
2
2
1
1
1
2
2
1
1
1
1
2
2
8
8
346
QTY.
4
4
4
4
4
2
2
4
4
1
1
1
4
4
1
1
2
2
16
16
1
2
2
2
2
1
1
2
2
1
1
1
2
2
1
1
1
1
1
1
8
8
349 355
QTY. QTY.
103
000
000
103
103
103
103
103
000
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
000
103
103
WARR.
CLASS
Prior to: 345- J906737, 349- J9102431
349- J9114233, 355- J9012316
Prior to: 345- J9067375, 346- J9072433,
349- J9114233/Up, 345- J9012316/Up
345- J9067375/Up, 346- J9072433/Up,
349- J9114233/Up
349- Prior to J9114233
Main High Side 349- Prior to J9114233
Use w/old style 2.5 quart mix tank
New style 3.5 quart mix tank
Power
Mix Hopper
355- J9053838
Prior to: 345- J9067375, 346- J9072433,
345- J9067375/Up, 346J9072433,
355 - J9053838/Up
345- J9067375/Up, 346- 9072433/Up,
355 - J9053838/Up
Prior to: 345- J9067375, 346- J9072433,
349- J9097086, 355- J9053838
349- J9097086/Up, 355- J9053838/Up
345- J9067375/Up, 346- J9072433/Up,
REMARKS
144
151
151
144
142/144
142/144
144
142/144
PARTS
UPDATE
+ Available Separately
Models 345, 346, 349 & 355
67
Parts List
018520
018521
018522
018523
043638
044534
017444
+Marker- No. 1
+Marker- No. 2
+Marker- No. 3
+Marker- No. 4
+Regulator- CO2 (Primary) 0- 100 PSI
+Valve- Check
+Valve- Solenoid
X34866
001486
021162
021029
018520
018521
043638
+Elbow A.- Restrictor
+Elbow- Union
+Restrictor- Air
+Gauge- Pressure
+Marker- No. 1
+Marker- No. 2
+Regulator (0- 100 PSI)
X45309-
X44508
Valve A.- Solenoid (Regulator/CO2)
043643
047496-
+Valve- Solenoid
+Manifold A.- CO2
030386
+Valve- Check
+Gauge- Pressure (0- 100 PSI)
043638
+Regulator (0- 100 PSI)
021029
018521
+Marker- No. 2
+Gauge- Pressure (0- 60 PSI)
018520
+Marker- No. 1
X47223-
043643
+Gauge- Pressure (0- 100 PSI)
Valve A.- Solenoid (Regulator/CO2)
021029
+Gauge- Pressure (0- 60 PSI)
+Restrictor- Air
1
2
2
2
2
1
1
1
1
2
X44937-
Valve A.- Solenoid (Regulator/CO2)
021162
053051-
Valve- Solenoid 1/8 ORF X 1/4S
1
2
044982-
Valve- Solenoid (Defrost)
2
345
QTY.
X34866
053511-
Valve- Sol 1/8ORF 1/4INX3/8OUT (Defrost)
+Elbow A.- Restrictor
043449-
PART
NUMBER
Valve- Solenoid (Liquid Line/Defrost)
DESCRIPTION
2
2
2
1
1
1
1
2
2
1
2
2
346
QTY.
4
4
2
1
1
1
1
1
1
1
1
2
4
4
1
1
1
1
2
2
2
1
1
4
349 355
QTY. QTY.
103
000
000
103
000
103
103
103
103
103
103
000
000
000
000
103
103
103
103
103
103
103
000
000
103
103
000
103
103
103
103
103
WARR.
CLASS
Prior to S/N J8040000
Prior to S/N J8054096 - See Manifold
Prior to S/N J8040000
J9055971/Up
Prior to J9053838, 355 - 1 Used Prior to
J9053838
346- J9072433/Up, 349- J9114233/Up
J9053838/Up, 355 - 2 Used Prior to
J9053838
355 - Prior to J9053838
REMARKS
129
129
128
144
142
142
PARTS
UPDATE
+ Available Separately
Parts List
68
Models 345, 346, 349 & 355
043643
044108
044110
044650
017450
016309- 12
044805
016306
029830
Gauge- Pressure (0- 100 PSI)
Label- Warn- Press (Low Water Pressure)
Label- Water Regulator
Leg- Rubber (Rubber Bumper)
Light- Indicator
Motor- Pump
Panel- Exterior
Pump- Water
Regulator (0- 50 PSI)
045166
028182
012906
038143
029439
048134
Belt
Belt
Capacitor- Run
Capacitor- Start
Capacitor- Run
Capacitor- Start
50 CYCLE
077124
044558
Filter- Water Line
Washer- 3/8 Flare- Nylon
053697
Filter- Water 1/4FFLINX1/4MFLOV
020565- 14
029834
Ferrule
Tube- Nylobrade (Pump to Carbonator Tank)
007096
Elbow- 3/8 MFL x 3/8 MPT
016292
049464
Switch- Low Pressure (H2O)
036408
Elbow- 3/8 FFL x 3/8 Barb
050258- 12
Kit A.- Probe & Float
Cord- Power
050257- 12
Probe A.- Carbonator w/Reed Switch
Carbonator
049455- 12
018595
Washer- Nylon Flare
REMOTE DISPENSER ASSEMBLY
046914- V
047496-
Video- Train Film- FCB Pressure
030386
+Valve- Solenoid
PART
NUMBER
+Valve- Check
DESCRIPTION
1
1
1
1
18
1
345
QTY.
2
2
2
2
19
1
346
QTY.
2
5
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
2
1
2
1
1
1
1
19
1
2
2
349 355
QTY. QTY.
103
103
103
103
000
000
000
000
103
103
103
103
103
103
103
000
000
103
000
000
000
103
103
103
103
103
103
000
000
103
103
WARR.
CLASS
TECUMSEH
TECUMSEH & COPELAND
BRISTOL
BRISTOL
Bulk R30333
Replaces 044734
115 Volt - Prior to J7062208
115 Volt - J7062208/Up
346- J9072433/Up, 355- J9012316
345- J9055921/Up, 346- J9072433/Up,
REMARKS
146, 147
119
PARTS
UPDATE
+ Available Separately
Models 345, 346, 349 & 355
69
Parts List
044422
038146
048133
051957- 12
051957- 40
Pulley (Beater Motor)
Relay- Start
Relay- Start
Relay- Start- Compressor
Relay- Start
1
X45116012796-
Blower Assembly
022505
012768-
Guard- Blower
Motor- Fan
044833- SP
048231
046431
046686
Panel- Left Side
Switch- Pressure - 350 PSI
Switch- Pressure - 350 PSI
Valve- Water
016289
048287
Condenser
+Blade- Fan (7” Push)
047540
Condenser- WC- Coax
Blower
1
012796-
1
1
1
1
1
1
1
053377
Blower- 100 CFM
1
1
1
1
1
1
1
1
1
2
2
2
1
2
1
1
2
2
2
2
2
2
2
2
1
2
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
345
346
349
355
QTY. QTY. QTY. QTY.
Accumulator- Copper 2”DIA 13”LG
WATER COOLED
037297
019624
Pulley (Beater Motor)
+Capacitor- Run - 4UF/370V
047178- 34
Motor- Fan 100 Watt
047279
029770- 27
Motor- Fan 50 Watt
+Blade- Fan (12”Push)
051960
Capacitor- Start
047061
012901
+Blade- Fan (12”Pull)
023606
Capacitor- Start- 145- 175UF/220V
PART
NUMBER
Capacitor- Run
DESCRIPTION
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
103
WARR.
CLASS
345- J9053838/Up, 346- J9071890/Up,
349- J9114879/Up, 355- J9072849
Repl 018278 (J8050000/Up)
345- J9071890/Up, 349- J9114879/Up
345- J9071890/Up
2/18/99/Up
COPELAND - J9053838/Up
COPELAND
TECUMSEH
BRISTOL
Fan Motor
BRISTOL
COPELAND - J9053838/Up
COPELAND - J9053838/Up
COPELAND
COPELAND - J9053838/Up
REMARKS
142
129
142
142
142
PARTS
UPDATE
BLK
RIBBON CABLE
SEE NOTE 2
12
10
2
4
6
8
J4
J6
J3
J5
W1
J2
RIBBON CABLE
SEE NOTE 2
RIBBON CABLE
SEE NOTE 2
1 2
J1
11
9
1
3
5
7
J7
CONTROL PCB A.
J9
BARREL 1
BLK
YEL
BARREL 2
BLK
BLK
BLK
BRN
BARREL 1
SYRUP OUT
SWITCH
PROXIMITY
SWITCHES
BLK
RED
BRN
BRN
BLK
C
NO
BARREL
1
BIB
SWITCH
BLK
BRN
BLK
BLK
BLU
BLU
BARREL
1
HOPPER
FILL
SWITCH
SEE NOTE 2
RIBBON CABLE
BRN
SEE NOTE 2
RIBBON CABLE
COMPRESSOR
CONTACTOR
T1
1
4
BLK
C02
PRESSURE
SWITCH
BLK
BLK
4 3 2 1
J5
1 2 3 4
1 2 3 4 5 6 7 8
J7
5
BLK
BARREL
2
LIQ. LINE
SOLENOID
3
1
J3
1 2 3 4 5 6 7 8
BLK
RED/BLK
J12
WHT
BLK
BLK
T2
INTERFACE PCB A. W1 JUMPER BLOCK DETAIL
L2
BRN
COMPRESSOR
CONTACTOR
BRN
BLK
PRP
PRP/WHT
X1
J14
NO
WHT/BLK
C
BARREL
2
BIB
SWITCH
BLK
A
RED
1 2
J1
RED/BLK
J13
B
BARREL
2
H20 SOL.
WHT
WHT
WHT
7 6 5 4 3 21
WHT
WHT
L2
W1
J2
BARREL 2
SYRUP OUT
SWITCH
COMPRESSOR
FIG.2
M
ORG/WHT
7 6 5 4 3 21
ORN
WHT/BLK STRIPE
L1
RED/WHT
PRP/WHT
INTERFACE PCB A.
J16
7 6 5 4 3 21
J4
J15
W2
7 6 5 4 3 21
J11
WHT
ORG/WHT
6 5 4 3 21
WHT
ORN
4 3 2 1
L1
BLK
RED
J6
WHT
BLU/WHT
BARREL
1
CO2 SOL.
WHT
RED/WHT
1
WHT
BRN
BLK
YEL
WHT/BLK
WHT/BLK
WHT
L1
LINE
L2
BLK
PRIMARY
LOAD L2
WHT
SECONDARY
CONT.
TRANS.
L1
EMI FILTER
IN
BLK
BLK
BRN OUT
PCB A.
OUT
CONTROL
SWITCH
SPST
RED/BLK
YEL
ORN
ORN
2. STRIPED WIRE ON RIBBON CABLES
MUST BE CONNECTED TO PIN 1
AT EACH END.
WHT
GROUND FRAME
SECURELY
OUT
IN
BLK
WHT
WHT
WHT
CARBONATOR FILL SWITCH
WHT
RIGHT BEATER MOTOR
FIG.1
LEFT BEATER MOTOR
FIG.1
RUN CAPACITOR USED
WITH 041401-27 OR
047178-34 MOTOR ONLY.
NOTE:
1. STATIC ELECTRICITY MAY CAUSE
DAMAGE TO SOLID STATE COMPONENTS.
ELIMINATE STATIC ELECTRICITY BY TOUCHING
GROUNDED UNIT BEFORE HANDLING SOLID STATE
COMPONENTS.
4
H2O
PRESSURE
SWITCH
RED
M
FAN
BARREL 1
LED
BLK/WHT
BARREL 2
LED
BARREL
2
DEFROST
SOLENOID
WHT
BARREL
2
CO2 SOL.
BLK
BRN
BLU
BARREL
2
HOPPER
FILL
SWITCH
WHT
WHT
RED/WHT
WHT
BRN
WHT
BARREL
2
SYR.SOL.
BLK
BARREL
1
SYR.SOL.
BRN
EMPTY (JUMPER USED FOR W.C. ONLY, SOFTWARE VER. 2.04).
EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED
EMPTY
SERVICE/TEST ONLY
EMPTY
EMPTY
HPCO
BARREL 1
BARREL 2
SEE NOTE 2
RIBBON CABLE
RED/WHITE
BLK
YEL
BLK
YEL
WHT
PRP/WHT
BLK
JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED
AS A MODEL 345, AIR COOLED WITH A H20 PRESSURE SWITCH.
BLK
J11
J10
BARREL 2
KEYPAD
RED
BARREL 1
KEYPAD
BLK
J10
J9
J8
BRN
BLK
ORG/WHT
1 2 3 4
BARREL
1
H20 SOL.
WHT/BLK
COMP.
CONT.
COIL
WHT/BLK
BARREL
1
LIQ. LINE
SOLENOID
PRP
BARREL
1
DEFROST
SOLENOID
BLK/YEL
YEL
BLK
BRN
BLU
LCD DISPLAY
BLK
BLK
PUMP
M
L2
BLK
BLK
15A FUSE
RED
WHT
RED
LINE
6
5
1
WHT
WHT/BLK
T4 OR YEL
A
2
1
BLU
4
5
1
2
RELAY
WHT
BLK
BRN
R
S
FIG.2
052396-1
RUN CAPACITOR
WHT
YEL
WHT/BLK
BLEED RESISTOR
BRN
C
WHT
LEESON
4
2
WHT/BLK
4
COPELAND COMPRESSOR WIRING
START CAPACITOR
EQUIPMENT
GROUND
FIG.1
INTERNAL OVERLOAD
WHT(120 VOLTS)
BLK(230 VOLTS)
BLK
YEL
1
BRN
BEATER MOTOR WIRING
MAGNATEK-CENTURY
YEL
P2 OR BRN
3
5
P1 OR PUR
T8 OR RED
2
1
T5 OR BLK
THERMAL OL
T1 OR BLU
GE/RBC BEATER MOTOR WIRING
CWLE-RED OR T8 INTERNAL ON #A, BLACK OR T5 INTERNAL ON #5
START
THERMISTORS
PROBES
WHT/BLK
WHT/BLK
WHT
WHT
WHT
WHT
WHT
BRN
MAIN
BLK
PRP/WHT
12
2
L1
WHT/BLK
WHT/BLK
1
11
345
053515-27
11/12/13
L2
BARREL
2
SYR.SOL.
BRN
BARREL
2
DEFROST
SOLENOID
M
FAN
WHT
CONTROL
SWITCH
SPST
BARREL 1
LED
YEL
L2
ORN
ORN
WHT
LEFT BEATER MOTOR
BLK
RUN CAPACITOR USED
WITH 041401-27 OR
047178-34 MOTOR ONLY.
YEL
LINE
IN
OUT
WHT
LOAD L2
PRIMARY
SECONDARY
CONT.
TRANS.
L1
EMI FILTER
L1
RED/BLK STR
BLK
BLK
IN
BRN OUT
PCB A.
OUT
WHT
WHT/BLK
RIGHT BEATER MOTOR
WHT
BLK
WHT
WHT
WHT
CARBONATOR FILL SWITCH
BLK
M
PUMP
L2
L3
BLK
BARREL
2
CO2 SOL.
RED/WHT
WHT
BLK
BLK/WHT
BARREL 2
LED
RED
4
H2O
PRESSURE
SWITCH
1
WHT/BLK
BLK
BLK
BLK
BLK
WHT
B
BRN
BLU
BARREL
2
HOPPER
FILL
SWITCH
WHT
BRN
WHT
BARREL
2
H20 SOL.
X1
J13
A
J14
7 6 5 4 3 21
RED/BLK
1 2
J1
PRP/WHT
BLK
PRP
BLK
NO
BARREL
2
BIB
SWITCH
C
WHT/BLK
BLK
BLK
BLK
BLK
15A FUSE
BARREL
2
LIQ. LINE
SOLENOID
2
J12
W1
7 6 5 4 3 21
BLK
J2
12
BARREL
1
CO2 SOL.
L1
WHT
BLK/WHT
BLK
RED/BLK
J3
1 2 3 4 5 6 7 8
RED
BRN
L3
L2
BLK
BARREL
1
SYR.SOL.
1
1
BARREL
1
H20 SOL.
WHT
ORG/WHT
3
J4
BARREL 2
SYRUP OUT
SWITCH
BRN
WHT
WHT
COMPRESSOR
CONTACTOR
T2
COMPRESSOR
CONTACTOR
T3
11
COMP.
CONT.
COIL
WHT
ORN
J16
7 6 5 4 3 21
BLK
BLK
BLK
WHT
WHT
BLK
BARREL
1
LIQ. LINE
SOLENOID
WHT
J15
7 6 5 4 3 21
RED/WHT
INTERFACE PCB A.
J11
W2
1 2 3 4
J5
1 2 3 4 5 6 7 8
J7
4 3 2 1
4 3 2 1
5
6 5 4 3 21
BLU/WHT
J6
BLK
BLK
PRP/WHT
THERMISTORS
PROBES
BARREL
1
DEFROST
SOLENOID
PRP/WHT
WHT
RED/WHT
BLK
YEL
BLK
YEL
SEE NOTE 2
SEE NOTE 2
BLU
BLU
RED
BLK
C02
PRESSURE
SWITCH
4
ORN
ORG/WHT
BRN
LCD DISPLAY
BARREL 2
KEYPAD
SEE NOTE 2
J9
RIBBON CABLE
RIBBON CABLE
BLK
BLK
BARREL
1
HOPPER
FILL
SWITCH
1
M
COMPRESSOR
NOTE:
1. STATIC ELECTRICITY MAY CAUSE
DAMAGE TO SOLID STATE COMPONENTS.
ELIMINATE STATIC ELECTRICITY BY TOUCHING
GROUNDED UNIT BEFORE HANDLING SOLID STATE
COMPONENTS.
WHT/BLK
WHT/BLK
ORG/WHT
1 2 3 4
WHT
BLK
2. STRIPED WIRE ON RIBBON CABLES
MUST BE CONNECTED TO PIN 1
AT EACH END.
WHT/BLK
WHT/BLK
SEE NOTE 2
BRN
BRN
BLK
BRN
NO
BLK
BLU
SEE NOTE 2
CONTROL PCB A.
J7
C
BARREL
1
BIB
SWITCH
BLK
RIBBON CABLE
BRN
T1
RED
J1
1 2
RED
BLK
PROXIMITY
SWITCHES
BARREL 1
SYRUP OUT
SWITCH
SERVICE/TEST ONLY
RED
WHT
BRN
BARREL 1
BLK
INTERFACE PCB A. W1 JUMPER BLOCK DETAIL
PRP/WHT
BRN
BLK
RIBBON CABLE
JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED
AS A MODEL 345, AIR COOLED WITH A H20 PRESSURE SWITCH.
PRP
WHT
WHT
WHT
WHT
WHT
WHT/BLK
BARREL 2
BARREL 1
HPCO
BRN
BLK
L1
BLK
COMPRESSOR
CONTACTOR
WHT/BLK
YEL
EMPTY
EMPTY
EMPTY - (JUMPER USED FOR W.C. ONLY, SOFTWARE VER. 2.04).
EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED
EMPTY
BLK/YEL
J10
J9
J8
J11
J10
BARREL 2
BLK
BLK
BLK
J4
J6
J3
J5
J2
W1
1
3
5
7
9
RED
RIBBON CABLE
11
BLK
BARREL 1
KEYPAD
SEE NOTE 2
10
2
4
6
8
RIBBON CABLE
12
BLK
YEL
BLK
BRN
L1
BLK
YEL
6
1
WHT
WHT/BLK
5
GROUND FRAME
SECURELY
YEL
4
1
WHT
WHT/BLK
2
LEESON
COMPRESSOR WIRING
BEATER MOTOR WIRING
MAGNATEK-CENTURY
COMPRESSOR
TERMINALS
LINE
345
053515-33
11/12/13
L2
BARREL
2
SYR.SOL.
WHT
BRN
WHT
RED/WHT
WHT
BARREL
2
DEFROST
SOLENOID
M
FAN
WHT
BARREL 1
LED
BLK/WHT
BRN
YEL
BLK
BLK
L2
BLK
LINE
LOAD L2
PRIMARY
WHT
SECONDARY
CONT.
TRANS.
L1
EMI FILTER
L1
OUT
IN
ORN
ORN
GRN/YEL
WHT
GRN/YEL
BLK
WHT
WHT
WHT
GRN/YEL
GRN/YEL
GRN/YEL
BLK
GRN/YEL
CARBONATOR FILL SWITCH
WHT
RIGHT BEATER MOTOR
FIG.1
LEFT BEATER MOTOR
FIG.1
RUN CAPACITOR USED
WITH 041401-27 OR
047178-34 MOTOR ONLY.
YEL
RED/BLK
CONTROL
SWITCH
SPST
IN
BRN OUT
PCB A.
OUT
WHT
M
PUMP
GRN/YEL
GRN/YEL
N
WHT
WHT
BARREL
2
CO2 SOL.
RED
BARREL 2
LED
BLK
BRN
BLU
BARREL
2
HOPPER
FILL
SWITCH
WHT/BLK
WHT/BLK
GRN/YEL
WHT
GROUND FRAME
SECURELY
NOTE:
1. STATIC ELECTRICITY MAY CAUSE
DAMAGE TO SOLID STATE COMPONENTS.
ELIMINATE STATIC ELECTRICITY BY TOUCHING
GROUNDED UNIT BEFORE HANDLING SOLID STATE
COMPONENTS.
4
H2O
PRESSURE
SWITCH
1
WHT
345
053515-40
11/12/13
3
1
5
1
P1 OR PUR
P2 OR BRN
2
BRN
A
BLK
4
2
R
S
WHT
LEESON
1
WHT/BLK
4
WHT/BLK
1
2
YEL
5
T4 OR YEL
T8 OR RED
2
THERMAL OL
T5 OR BLK
T1 OR BLU
6
WHT
FIG.1
5
1
RELAY
4
BLU
YEL
WHT/BLK
WHT
052396-1
RUN CAPACITOR
BLEED RESISTOR
BRN
INTERNAL OVERLOAD
WHT(120 VOLTS)
BLK(230 VOLTS)
WHT
C
BLK
EQUIPMENT
GROUND
FIG.2
COPELAND COMPRESSOR WIRING
START CAPACITOR
BRN
BEATER MOTOR WIRING
MAGNATEK-CENTURY
YEL
MAIN
GE/RBC BEATER MOTOR WIRING
CWLE-RED OR T8 INTERNAL ON #A, BLACK OR T5 INTERNAL ON #5
LINE
START
BLK
B
WHT
BARREL
2
H20 SOL.
BLK
PRP
PRP/WHT
X1
J13
A
BLK
J14
7 6 5 4 3 21
1 2
J1
RED/BLK
J2
RED
NO
BARREL
2
BIB
SWITCH
C
WHT/BLK
GRN/YEL
WHT
RED/WHT
15A FUSE
BARREL
2
LIQ. LINE
SOLENOID
J12
W1
7 6 5 4 3 21
BLK
2
L1
WHT
BLK/WHT
BLK
RED/BLK
J3
1 2 3 4 5 6 7 8
12
BARREL
1
CO2 SOL.
1
BARREL 2
SYRUP OUT
SWITCH
BRN
L2
COMPRESSOR
CONTACTOR
T2
WHT
WHT
WHT
BARREL
1
SYR.SOL.
WHT
ORG/WHT
3
J4
ORG/WHT
BRN
1
BARREL
1
H20 SOL.
WHT
ORN
J16
7 6 5 4 3 21
BLK
WHT
WHT
WHT
BLK
COMP.
CONT.
COIL
WHT
J15
7 6 5 4 3 21
RED/WHT
PRP/WHT
INTERFACE PCB A.
J11
W2
1 2 3 4
J5
1 2 3 4 5 6 7 8
J7
4 3 2 1
4 3 2 1
5
6 5 4 3 21
BLU/WHT
J6
BLK
BRN
THERMISTORS
PROBES
BARREL
1
LIQ. LINE
SOLENOID
BLU
BLU
BLK
RED
BLK
M
ORN
LCD DISPLAY
BARREL
1
DEFROST
SOLENOID
PRP/WHT
WHT
SEE NOTE 2
RED/WHT
BLK
YEL
BLK
YEL
RIBBON CABLE
SEE NOTE 2
BLK
BLK
SEE NOTE 2
BRN
BRN
BLK
BARREL
1
HOPPER
FILL
SWITCH
4
C02
PRESSURE
SWITCH
1
BLK
BLK
2. STRIPED WIRE ON RIBBON CABLES
MUST BE CONNECTED TO PIN 1
AT EACH END.
WHT/BLK
WHT/BLK
RIBBON CABLE
RIBBON CABLE
BLK
BRN
BLK
BARREL
1
BIB
SWITCH
NO
T1
WHT/BLK
WHT/BLK
11
RIBBON CABLE
ORG/WHT
1 2 3 4
BARREL 2
KEYPAD
BLK
RED
BRN
C
L1
COMPRESSOR
CONTACTOR
BLU
SEE NOTE 2
J9
PROXIMITY
SWITCHES
BARREL 1
SYRUP OUT
SWITCH
BRN
BLK
SERVICE/TEST ONLY
RED
RIBBON CABLE
J7
BARREL 2
BARREL 1
HPCO
BLK
RED
BARREL 1
BLK
INTERFACE PCB A. W1 JUMPER BLOCK DETAIL
PRP/WHT
WHT
BRN
YEL
JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED
AS A MODEL 345, AIR COOLED WITH A H20 PRESSURE SWITCH.
PRP
BRN
BLK
J11
J10
WHT
WHT
WHT
WHT
WHT
WHT/BLK
COMPRESSOR
FIG.2
WHT/BLK
J10
J9
J8
RIBBON CABLE
CONTROL PCB A.
1
EMPTY
EMPTY
BLK/YEL
J1
1 2
W1
3
5
7
9
BLK
J4
J6
J3
J5
J2
BARREL 2
BLK
EMPTY (JUMPER USED FOR W.C. ONLY, SOFTWARE VER. 2.04).
EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED
EMPTY
RED
SEE NOTE 2
11
BLK
BARREL 1
KEYPAD
4
6
8
10
2
SEE NOTE 2
12
BLK
YEL
BLK
BRN
L1
BLK
15 A
FUSE
J12
7 6 5 4 3 21
L2
W1
2
L1
BLK
T2
A
BLK
J14
BARREL
2
SYR.SOL.
C
WHT
WHT
NO
BARREL
2
BIB
SWITCH
BARREL
2
CO2 SOL.
COMP.
CONT.
COIL
BARREL 2
4
BLK
YEL
L1
WHT
BLK
L2
WHT
BLK
BRN
S
R
052396-1
WHT
BLK
WHT
WHT
BLK
BLK
RUN CAPACITOR
BLEED RESISTOR
BRN
C
INTERNAL OVERLOAD
2
RELAY
5
1
FIG.2
BLK
CARBONATOR FILL SWITCH
WHT
RIGHT BEATER MOTOR
FIG.1
WHT
LEFT BEATER MOTOR
FIG.1
YEL
COPELAND COMPERSSOR WIRING - CSR
BLU
4
WHT(120 VOLTS; 220V-50Hz)
BLK(230 VOLTS)
L2
START CAPACITOR
EQUIPMENT
GROUND
BLK
LINE
LOAD L2
PRIMARY
IN
T2
RIGHT
COMPRESSOR
CONTRACTOR
OUT
BLK
WHT
SECONDARY
CONT.
TRANS.
WHT
ORN
ORN
EMI FILTER
M
WHT/BLK
WHT/BLK
OUT
IN
BLK
BLK
L1
LINE
DEFROST
SOLENOID
BARREL 2
BLK
RED/BLK
CONTROL
SWITCH
SPST
1
T1
RIGHT
COMPRESSOR
FIG.2
BRN OUT
PCB A.
BARREL 1
LED
L1
H2O
PRESSURE
SWITCH
WHT/BLK
BARREL
2
HOPPER
FILL
SWITCH
RED
BARREL 2
LED
BLK
PRP/WHT
PRP
BLU
WHT
BRN
WHT
RED/WHT
BLK
B
BARREL
2
H20 SOL.
BRN
WHT/BLK
BRN
BLK
RED
X1
J13
7 6 5 4 3 21
J1
RED/BLK
1 2
L2
BARREL 2
SYRUP OUT
SWITCH
J2
12
7 6 5 4 3 21
BLK
RED/BLK
RED
J3
1 2 3 4 5 6 7 8
RIGHT
HPCO
BLK
1
BARREL
1
CO2 SOL.
7 6 5 4 3 21
ORG/WHT
WHT
BARREL
1
SYR.SOL.
RUN CAPACITOR
USED WITH 046536-27
MOTOR ONLY
BARREL
1
H20 SOL.
6 5 4 3 21
J4
3
1
INTERFACE PCB A.
WHT
BLK/WHT
J16
5
J15
W2
1 2 3 4
J5
1 2 3 4 5 6 7 8
J7
4 3 2 1
4 3 2 1
RED
BLK
BLK
BLK
C02
PRESSURE
SWITCH
4
M
11
BLK
M
BARREL 1
COMP.
CONT.
COIL
BLU
J11
ORN
WHT
BLU/WHT
BLK
J6
SEE NOTE 2
BLK
BLU
BARREL
1
HOPPER
FILL
SWITCH
1
BLK
ORG/WHT
L1
THERMISTORS
PROBES
BARREL 1
DEFROST
SOLENOID
RIBBON CABLE
RIBBON CABLE
BRN
RIBBON CABLE SEE NOTE 2
BRN
BLK
BLK
BRN
NO
BLK
SEE NOTE 2
BLK
WHT
RED/WHT
BLK
YEL
BLK
YEL
BLOWER
BRN
BARREL
1
BIB
SWITCH
C
T1
WHT
WHT
LCD DISPLAY
BARREL 2
KEYPAD
J9
J7
CONTROL PCB A.
J1
1 2
BRN
RED
BLK
PROXIMITY
SWITCHES
BARREL 1
SYRUP OUT
SWITCH
BLK
BRN
L1
LEFT
COMPRESSOR
CONTACTOR
BLK
RIGHT
COMPRESSOR
CONTRACTOR
ELIMINATE STATIC ELECTRICITY BY TOUCHING
DAMAGE TO SOLID STATE COMPONENTS.
1. STATIC ELECTRICITY MAY CAUSE
NOTE:
WHT
GROUNDING UNIT BEFORE HANDLING SOLID
M
PUMP
L2
346
053566-27
11/12/13
1
5
P1 OR PUR
1
BRN
A
4
2
WHT
YEL
WHT/BLK
GE/RBC BEATER MOTOR WIRING
CWLE-RED OR T8 INTERNAL ON #5, BLACK OR T5 INTERNAL ON #A}
3
P2 OR BRN
WHT
LEESON
1
WHT/BLK
4
WHT/BLK
1
2
YEL
5
T4 OR YEL
T8 OR RED
2
THERMAL OL
T5 OR BLK
T1 OR BLU
6
WHT
FIG.1
BEATER MOTOR WIRING
MAGNATEK-CENTURY
YEL
MAIN
BLU/WHT
STATE COMPONENTS.
START
RIBBON CABLE
BLK
BLK
BLK
ORN
ORG/WHT
BRN
GROUND FRAME
SECURELY
WHT
MUST BE CONNECTED TO PIN 1 AT
EACH END.
WHT/BLK
WHT/BLK
BRN
2. STRIPED WIRE ON RIBBON CABLES
WHT/BLK
BRN
EMPTY (JUMPER USED FOR W.C. ONLY, SOFTWARE VER. 2.04).
EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED
EMPTY
SERVICE/TEST ONLY
BLU
BARREL 1
INTERFACE PCB A. W1 JUMPER BLOCK DETAIL
RED
WHT
PRP/WHT
BLK
RED
SEE NOTE 2
JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED
AS A MODEL 346, AIR COOLED WITH A H20 PRESSURE SWITCH.
PRP
BRN
LEFT
COMPRESSOR
FIG.2
BLK
BARREL 2
BARREL 1
LEFT
HPCO
BLK
LEFT
COMPRESSOR
CONTACTOR
BLK
BRN
1 2 3 4
WHT
WHT
WHT
WHT
WHT
WHT
BLK
WHT/BLK
RIBBON CABLE
EMPTY (JUMPER USED FOR MODEL 346, SOFTWARE VER. 2.04).
EMPTY
BLK
BLK
BLK
BARREL 1
KEYPAD
3
5
1
4
6
7
9
W1
8
10
SEE NOTE 2
11
2
RIBBON CABLE
12
BLK/YEL
WHT/BLK
J10
J8
J9
RED
BLK
J11
J10
SEE NOTE 2
BLK
J4
J6
J3
J5
J2
BARREL 2
YEL
BLK
YEL
BLK
BLK
BRN
BLK
BLK
SEE NOTE 2
M
BLK
BLK
BLK
BRN
NO
BLU
BLU
BARREL
1
CO2 SOL.
L1
15 A
FUSE
J12
BLK
L2
W1
7 6 5 4 3 21
BLK
RED
RED/BLK
J3
1 2 3 4 5 6 7 8
BARREL
2
SYR.SOL.
WHT
BRN
WHT
RED/WHT
WHT
WHT
BLU
NO
BARREL
2
CO2 SOL.
BLK
COMP.
CONT.
COIL
BARREL 2
DEFROST
SOLENOID
BARREL 2
BLK
RED/BLK
CONTROL
SWITCH
SPST
BRN OUT
PCB A.
BARREL 1
LED
1
4
H2O
PRESSURE
SWITCH
BLK/WHT
BARREL 2
LED
RED
BARREL
2
HOPPER
FILL
SWITCH
L1
LINE
L2
YEL
WHT
BLK
BLK
BLK
BLK
BLK
CARBONATOR FILL SWITCH
WHT
RIGHT BEATER MOTOR
L3
LEFT BEATER MOTOR
WHT
ORN
ORN
IN
OUT
WHT
LOAD L2
PRIMARY
SECONDARY
CONT.
TRANS.
L1
EMI FILTER
YEL
BLK
BLK
IN
OUT
WHT
T3
L2
RIGHT
COMPRESSOR
CONTRACTOR
T2
WHT
WHT
BLK
WHT
BLK
M
PUMP
L2
L3
BLK
BLK
B
C
BARREL
2
BIB
SWITCH
PRP
PRP/WHT
BLK
BARREL
2
H20 SOL.
X1
J13
A
BLK
BRN
J14
7 6 5 4 3 21
1 2
J1
RED/BLK
J2
RED
BRN
BARREL 2
SYRUP OUT
SWITCH
WHT/BLK
WHT/BLK
BLK
BLK
BLK
BLK
BARREL
1
SYR.SOL.
WHT
1
RIGHT
HPCO
BLK
WHT/BLK
M
BLK
ORG/WHT
J16
7 6 5 4 3 21
WHT
ORN
BARREL
1
H20 SOL.
BLK
J15
7 6 5 4 3 21
3
J4
INTERFACE PCB A.
WHT
BLK/WHT
J11
W2
1 2 3 4
J5
1 2 3 4 5 6 7 8
J7
4 3 2 1
4 3 2 1
BLK
BLK
4
5
6 5 4 3 21
BLU/WHT
J6
BLK
RED
1
C02
PRESSURE
SWITCH
L3
BLK
BLK
RIGHT
COMPRESSOR
CONTRACTOR
BLK
BLK
RUN CAPACITOR
USED WITH 046536-27
MOTOR ONLY
BLK
BARREL
1
HOPPER
FILL
SWITCH
BLK
T3
L2
LEFT
COMPRESSOR
CONTACTOR
T2
T1
RIGHT
COMPRESSOR
BLK
BLK
BLK
C
BLK
BLK
WHT
WHT
THERMISTORS
PROBES
BARREL 1
DEFROST
SOLENOID
SEE NOTE 2
BARREL 1
COMP.
CONT.
COIL
RIBBON CABLE
SEE NOTE 2
BRN
BRN
BLK
SEE NOTE 2
RIBBON CABLE
RED/WHT
BLK
YEL
BLK
YEL
WHT
BLK
BLOWER
BRN
BARREL
1
BIB
SWITCH
BLK
M
ORN
ORG/WHT
BRN
LEFT
COMPRESSOR
CONTACTOR
L1
WHT
LCD DISPLAY
J9
BRN
RIBBON CABLE
BRN
T1
LEFT
COMPRESSOR
BLK
BLU/WHT
RIGHT
COMPRESSOR
CONTRACTOR
WHT/BLK
BARREL 2
KEYPAD
RIBBON CABLE
CONTROL PCB A.
J7
RED
BLK
PROXIMITY
SWITCHES
BLK
BRN
BARREL 1
SYRUP OUT
SWITCH
BLK
L1
LEFT
COMPRESSOR
CONTACTOR
GROUND FRAME
SECURELY
WHT
NOTE:
1. STATIC ELECTRICITY MAY CAUSE
DAMAGE TO SOLID STATE COMPONENTS.
ELIMINATE STATIC ELECTRICITY BY TOUCHING
GROUNDED UNIT BEFORE HANDLING SOLID STATE
COMPONENTS.
WHT/BLK
WHT/BLK
BRN
2. STRIPED WIRE ON RIBBON CABLES
MUST BE CONNECTED TO PIN 1
AT EACH END.
BLU
ORG/WHT
1 2 3 4
BARREL 1
BLK
EMPTY
EMPTY (JUMPER USED FOR W.C. ONLY, SOFTWARE VER. 2.04).
EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED
EMPTY
SERVICE/TEST ONLY
RED
J1
1 2
BARREL 2
BARREL 1
LEFT
HPCO
YEL
INTERFACE PCB A. W1 JUMPER BLOCK DETAIL
RED
BARREL 2
BLK
BLK
BLK
WHT
PRP/WHT
WHT
BRN
SEE NOTE 2
EMPTY (JUMPER USED FOR MODEL 346, SOFTWARE VER. 2.04).
BLK
RIBBON CABLE
JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED
AS A MODEL 346, AIR COOLED WITH A H20 PRESSURE SWITCH.
PRP
BRN
BLK
J10
J9
J8
WHT
WHT
WHT
WHT
WHT
WHT/BLK
2
1
3
5
WHT/BLK
12
7
9
BLK/YEL
1
2
4
6
BLK
11
8
10
RED
J11
J10
BARREL 1
KEYPAD
SEE NOTE 2
W1
RIBBON CABLE
11
BLK
J4
J6
J3
J5
J2
12
BLK
YEL
BLK
BRN
L1
BLK
YEL
6
1
WHT
WHT/BLK
5
YEL
4
1
WHT
WHT/BLK
2
LEESON
COPELAND COMPRESSOR WIRING
BEATER MOTOR WIRING
MAGNATEK-CENTURY
COMPRESSOR
TERMINALS
LINE
346
053566-33
11/12/13
BLK
RED
M
WHT
BLOWER
(FIG 3)
BARREL 1
COMP.
CONT.
COIL
BLU
BARREL
1
H20 SOL.
BARREL
1
SYR.SOL.
ORG/WHT
WHT
BARREL
1
CO2 SOL.
J16
7 6 5 4 3 21
ORN
WHT
BLU/WHT
BLK
J15
7 6 5 4 3 21
J4
3
1
L1
15 A
FUSE
RIGHT
HPCO
WHT
J12
BLK
BARREL
2
SYR.SOL.
C
WHT
WHT
NO
BARREL
2
BIB
SWITCH
BARREL
2
CO2 SOL.
DEFROST
SOLENOID
BARREL 2
BLK
BLK
4
BLK
L1
L1
L2
GRN/YEL
LINE
LOAD L2
PRIMARY
IN
YEL
WHT
L2
CAP
BLK 60 HZ
RED 50 HZ
BRN
WHT COM
EXTRA
MAIN
5
208/240
6
4
1
START
50/60 HZ
THERMAL
O.L.
2
2C
MAIN
FIG. 3
WHT
GRN/YELL
3
WHT
GRN/YEL
WHT
CARBONATOR FILL SWITCH
BLK
BLK
GRN/YEL
GRN/YEL
WHT
WHT
GE BLOWER MOTOR SCHEMATIC
BRN
GRN/YEL
WHT
RIGHT BEATER MOTOR
FIG.1
WHT
LEFT BEATER MOTOR
FIG.1
WHT
T2
RIGHT
COMPRESSOR
CONTACTOR
OUT
WHT
WHT
SECONDARY
CONT.
TRANS.
WHT
WHT/BLK
WHT/BLK
M
RIGHT
COMPRESSOR
FIG.2
ORN
ORN
EMI FILTER
YEL
COMP.
CONT.
COIL
BARREL 2
WHT
RED/BLK
CONTROL
SWITCH
SPST
1
T1
OUT
BROWN OUT IN
PCB A.
BARREL 1
LED
L1
H2O
PRESSURE
SWITCH
BLK/WHT
BARREL
2
HOPPER
FILL
SWITCH
RED
BARREL 2
LED
BLK
PRP/WHT
PRP
BLU
WHT
BRN
WHT
RED/WHT
BLK
B
BARREL
2
H20 SOL.
BRN
GRN/YEL
WHT/BLK
BRN
BLK
RED
X1
J13
A
J14
7 6 5 4 3 21
1 2
J1
RED/BLK
J2
L2
BARREL 2
SYRUP OUT
SWITCH
T2
LEFT
COMPRESSOR
CONTACTOR
BLK
L2
W1
7 6 5 4 3 21
BLK
1 2 3 4 5 6 7 8
J3
RED/BLK
RED
INTERFACE PCB A.
WHT
BLK/WHT
J11
5
6 5 4 3 21
W2
1 2 3 4
J5
1 2 3 4 5 6 7 8
J7
4 3 2 1
4 3 2 1
RED
BLK
BLK
BLK
C02
PRESSURE
SWITCH
4
M
2
THERMISTORS
PROBES
BARREL 1
DEFROST
SOLENOID
BLK
BLU
SEE NOTE 2
J6
SEE NOTE 2
BLK
WHT
RED/WHT
BLK
YEL
BLK
YEL
RIBBON CABLE
RIBBON CABLE
BRN
BARREL
1
HOPPER
FILL
SWITCH
1
BLK
WHT
WHT
LCD DISPLAY
J9
J7
BLK
BLK
BRN
NO
BARREL
1
BIB
SWITCH
C
T1
LEFT
COMPRESSOR
FIG.2
12
J1
BRN
RIBBON CABLE SEE NOTE 2
BRN
BLK
RED
BLK
PROXIMITY
SWITCHES
BARREL 1
SYRUP OUT
SWITCH
BLK
BRN
L1
LEFT
COMPRESSOR
CONTACTOR
BLK
RIGHT
COMPRESSOR
CONTACTOR
DAMAGE TO SOLID STATE COMPONENTS.
ELIMINATE STATIC ELECTRICITY BY TOUCHING
GROUNDING UNIT BEFORE HANDLING SOLID
STATE COMPONENTS.
M
PUMP
N
346
053566-40
11/12/13
YEL
3
1
5
1
P1 OR PUR
P2 OR BRN
BRN
A
4
C
BRN
BLK
4
2
WHT
WHT
YEL
WHT/BLK
R
RUN CAPACITOR
052396-1
BLEED RESISTOR
BRN
LEESON
1
WHT/BLK
YEL
WHT/BLK
WHT
2
1
5
T4 OR YEL
T8 OR RED
2
T5 OR BLK
THERMAL OL
T1 OR BLU
6
MAGNATEK-CENTURY
FIG.1
BEATER MOTOR WIRING
WHT
INTERNAL OVERLOAD
2
RELAY
5
1
BLU
4
WHT(120 VOLTS; 220V-50Hz)
BLK(230 VOLTS)
BLK
EQUIPMENT
GROUND
START CAPACITOR
COPELAND COMPRESSOR WIRING
FIG.2
S
GE/RBC BEATER MOTOR WIRING
CWLE-RED OR T8 INTERNAL ON #A, BLACK OR T5 INTERNAL ON #5
LINE
MAIN
WHT
1. STATIC ELECTRICITY MAY CAUSE
NOTE:
BLU/WHT
MUST BE CONNECTED TO PIN 1 AT
START
WHT
WHT
WHT
GRN/YEL
GRN/YEL
GRN/YEL
ORG/WHT
1 2 3 4
BARREL 2
KEYPAD
SEE NOTE 2
CONTROL PCB A.
RIBBON CABLE
1 2
BARREL 2
BARREL 1
LEFT
HPCO
BLK
BLK
WHT
EACH END.
WHT/BLK
WHT/BLK
BRN
2. STRIPED WIRE ON RIBBON CABLES
WHT/BLK
ORN
ORG/WHT
BRN
GROUND FRAME
SECURELY
BLU
BRN
EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED
EMPTY
SERVICE/TEST ONLY
INTERFACE PCB A. W1 JUMPER BLOCK DETAIL
RED
1
1
EMPTY (JUMPER USED FOR MODEL 346, SOFTWARE VER. 2.04).
EMPTY
BLK
WHT
PRP/WHT
BLK
RED
BRN
BARREL 2
EMPTY (JUMPER USED FOR W.C. ONLY, SOFTWARE VER. 2.04).
BLK
RIBBON CABLE
JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED
AS A MODEL 346, AIR COOLED WITH A H20 PRESSURE SWITCH.
PRP
WHT
WHT
WHT
WHT
WHT
WHT
WHT/BLK
BLK
WHT/BLK
11
SEE NOTE 2
W1
3
5
7
9
11
BLK/YEL
J8
J10
BLK
BARREL 1
KEYPAD
RIBBON CABLE
L1
2
4
6
8
10
12
BLK
J9
RED
BLK
J11
J10
SEE NOTE 2
BLK
J4
J6
J3
J5
J2
BARREL 1
YEL
BLK
YEL
BLK
BLK
BRN
BLK
BLK
15A
FUSE
2
12
BARREL
1
CO2 SOL.
1
BLK
BARREL
1
SYR.SOL.
BLK
BARREL
2
H20 SOL.
B
BARREL
2
SYR.SOL.
WHT
WHT
WHT
PRP/WHT
PRP
BARREL
2
CO2 SOL.
RED
COMP.
CONT.
COIL
BARREL 2
DEFROST
SOLENOID
BARREL 2
WHT
RED/BLK
CONTROL
SWITCH
SPST
BARREL 1
LED
BRN OUT
PCB A.
4
H2O
PRESSURE
SWITCH
BLK/WHT
BARREL 2
LED
BLK
BRN
BLU
BRN
WHT
RED/WHT
BLK
BARREL
2
HOPPER
FILL
SWITCH
1
LINE
GRN/YEL
L1
L2
LOAD L2
PRIMARY
YEL
L3
BLK
BLK
GRN/YEL
BLK
GRN/YEL
BLK
CONTROL
ENCLOSURE(S)
WHT
GRN/YEL
WHT
WHT
WHT
GRN/YEL
BLK
GRN/YEL
BLK
CARBONATOR FILL SWITCH
WHT
RIGHT BEATER MOTOR
WHT
LEFT BEATER MOTOR
WHT
ORN
ORN
IN
OUT
WHT
SECONDARY
CONT.
TRANS.
L1
EMI FILTER
YEL
BLK
BLK
IN
OUT
WHT
WHT/BLK
WHT/BLK
T3
L2
RIGHT
COMPRESSOR
CONTRACTOR
T2
M
PUMP
GRN/YEL
N
L2
BLK
WHT
BARREL
1
H20 SOL.
J13
X1
J14
7 6 5 4 3 21
A
BLK
NO
BARREL
2
BIB
SWITCH
C
BLK
BLK
BLK
BLK
M
BARREL 1
COMP.
CONT.
COIL
L2
J1
RED/BLK
1 2
RED
BRN
WHT/BLK
BRN
BLK
BLK
GRN/YEL
M
WHT
WHT
RED
BLOWER
(FIG 1)
WHT
ORG/WHT
J12
W1
7 6 5 4 3 21
BLK
J2
L3
BARREL 2
SYRUP OUT
SWITCH
T3
L2
LEFT
COMPRESSOR
CONTACTOR
T2
BLK
RIGHT
COMPRESSOR
CONTRACTOR
L3
CAP
RED 50 HZ
BLK 60 HZ
BRN
WHT COM
BRN
YEL
EXTRA
MAIN
5
208/240
6
4
1
START
50/60 HZ
THERMAL
O.L.
2
2C
1
WHT
LEESON
4
WHT/BLK
YEL
WHT/BLK
WHT
2
1
5
FIG. 1
3
GE MOTOR SCHEMATIC
6
346
053566-58
11/12/13
COPELAND COMPRESSOR WIRING
BEATER MOTOR WIRING
MAGNATEK-CENTURY
COMPRESSOR
TERMINALS
LINE
MAIN
ORN
WHT
L1
BLK
RED
RED/BLK
J3
1 2 3 4 5 6 7 8
RIGHT
HPCO
BLK
WHT
WHT
THERMISTORS
PROBES
BARREL 1
DEFROST
SOLENOID
BLK
J16
7 6 5 4 3 21
BLU/WHT
J15
7 6 5 4 3 21
J4
3
1
INTERFACE PCB A.
WHT
BLK/WHT
J11
5
6 5 4 3 21
W2
1 2 3 4
J5
1 2 3 4 5 6 7 8
J7
4 3 2 1
4 3 2 1
BLK
BLK
BLK
11
SEE NOTE 2
L1
RIBBON CABLE
LCD DISPLAY
BLK
WHT
RED/WHT
BLK
YEL
BLK
YEL
SEE NOTE 2
SEE NOTE 2
BLU
J6
RED
BLK
BLK
C02
PRESSURE
SWITCH
4
M
T1
WHT
RIGHT
COMPRESSOR
GRN/YEL
GRN/YEL
GRN/YEL
ORG/WHT
1 2 3 4
BARREL 2
KEYPAD
SEE NOTE 2
J9
RIBBON CABLE
RIBBON CABLE
BLK
SEE NOTE 2
BLK
BLU
BARREL
1
HOPPER
FILL
SWITCH
1
BLK
LEFT
COMPRESSOR
CONTACTOR
L1
RIGHT
COMPRESSOR
CONTRACTOR
WHT/BLK
ORN
ORG/WHT
BRN
GROUND FRAME
BLK
BLK
BLK
BLK
BLK
WHT
NOTE:
1. STATIC ELECTRICITY MAY CAUSE
DAMAGE TO SOLID STATE COMPONENTS.
ELIMINATE STATIC ELECTRICITY BY TOUCHING
GROUNDED UNIT BEFORE HANDLING SOLID STATE
COMPONENTS.
GRN
BLU/WHT
2. STRIPED WIRE ON RIBBON CABLES
MUST BE CONNECTED TO PIN 1
AT EACH END.
WHT/BLK
WHT/BLK
SEE NOTE 2
CONTROL PCB A.
EMPTY
SERVICE/TEST ONLY
RED
RIBBON CABLE
J7
BRN
BRN
RIBBON CABLE
BLK
BRN
BLK
NO
BARREL
1
BIB
SWITCH
C
T1
RED
BARREL 2
RED
BLK
PROXIMITY
SWITCHES
BARREL 1
SYRUP OUT
SWITCH
BRN
L1
BLK
LEFT
COMPRESSOR
BLK
J1
1 2
BARREL 1
LEFT
HPCO
BLK
BRN
BLK
INTERFACE PCB A. W1 JUMPER BLOCK DETAIL
BLU
WHT
BRN
WHT
PRP/WHT
BRN
BLK
BARREL 1
BLK
JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED
AS A MODEL 346, AIR COOLED WITH A H20 PRESSURE SWITCH.
PRP
WHT
WHT
WHT
WHT
WHT
WHT/BLK
YEL
BLK
BLK
WHT/BLK
BARREL 2
BLK
SECURELY
EMPTY (JUMPER USED FOR MODEL 346, SOFTWARE VER. 2.04).
EMPTY
EMPTY (JUMPER USED FOR W.C. ONLY, SOFTWARE VER. 2.04)
EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED
BLK/YEL
J10
J9
J8
LEFT
COMPRESSOR
CONTACTOR
BLK
RIBBON CABLE
W1
1
3
5
7
9
RED
J11
J10
BARREL 1
KEYPAD
2
4
6
8
J2
10
11
BLK
J4
J6
J3
J5
12
BLK
YEL
BLK
BRN
BLK
BLK
L2
BLK
BLK
M
BRN
RED/WHT
BARREL
2
SYR.SOL.
CARB.
PUMP
BLK
WHT
WHT
WHT
BLK
BARREL
2
CO2 SOL.
BLK
YEL
RED/BLK
BLK
LEFT
BEATER
MOTOR
(SEE FIG 1)
WHT
WHT
BARREL
2
DEFROST
SOLENOID
L1 LOADL2
PRIMARY
BLU
SECONDARY
CONT.
TRANS.
BARREL 2
LED
RED
BLU
WHT/BLK
RED
CONTROL
L1 LINE L2
SWITCH
EMI FILTER
BARREL 1
LED
RIBBON CABLE
BLK
RIBBON CABLE
BARREL
2
HOPPER
FILL
SWITCH
B
J14
BLK
X1
J13
7 6 5 4 3 2 1
A
WHT
BARREL
2
H20 SOL.
CARB. FILL SWT
WHT
BARREL
2
LIQ. LINE
SOLENOID
J12
7 6 5 4 3 2 1
1
11
2
12
WHT
BARREL
1
CO2 SOL.
L1
W1
J1
RED/BLK
1 2
BLK
BARREL
2
BIB
SWITCH
RED
BLK.
BLK
WHT
IN
BLU
RED
BRN
BRN
BLK
WHT
BLK
BLU
BLK
ORN
BARREL
3
H20 SOL.
BLU/WHT
WHT
BARREL
3
SYR.SOL
WHT
ORG/WHT
J15
7 6 5 4 3 2 1
BARREL
3
CO2 SOL.
WHT
RED
J16
7 6 5 4 3 2 1
1
BLK
L1
M
BLOWER
BLK
W1
BLK
BLK
WHT
4
BLK
BARREL 4
LED
BARREL
4
CO2 SOL.
BLK
YEL
WHT
RED/WHT
BLK
1
BLK
WHT/BLK
H2O
PRESSURE
SWITCH
BARREL 3
LED
BRN
WHT
BARREL
4
SYR.SOL.
RUN CAPACITOR USED WITH
46536-27 MOTOR ONLY.
BARREL
4
H20 SOL.
WHT
ORG/WHT
L2
BARREL
4
HOPPER
FILL
SWITCH
B
J14
X1
J13
A
PRP/WHT
PRP
1 2
J1
RED/BLK
J2
BLK
BARREL
4
BIB
SWITCH
T2
RIGHT COMPRESSOR
CONTACTOR
BLK
RED
BLK
BLK
BRN
BLK
7 6 5 4 3 2 1
WHT
WHT
L2
BARREL
4
LIQ. LINE
SOLENOID
J12
7 6 5 4 3 2 1
BLU
BLK
M
BARREL 4
SYRUP OUT
SWITCH
1 2 3 4 5 6 7 8
J3
RED/BLK
RIGHT INTERFACE PCB A.
3
J4
J11
W2
1 2 3 4
J5
4
T1
5
6 5 4 3 2 1
L1
1
CO2
PRESSURE
SWITCH
BLK
BLK
1 2 3 4 5 6 7 8
J7
4 3 2 1
4 3 2 1
BLK
BARREL
3
HOPPER
FILL
SWITCH
RED
J6
PRP/WHT
RIGHT
COMP.
CONT.
COIL
WHT
BLK
BLK
BLK
BRN
BARREL 3
BIB SWITCH
BLK
BLU
RIBBON CABLE
SEE NOTE 2
RED/WHT
BARREL
3
LIQ. LINE
SOLENOID
OUT
OUT
BARREL
3
DEFROST
SOLENOID
RED
BLU
IN
BLU
BRN
BARREL 3
SYRUP OUT
SWITCH
BLK
BARREL 3
BARREL 4
RIBBON CABLE SEE NOTE 2
RED
BRN OUT
PCB A.
PROXIMITY
SWITCH
RIGHT
HPCO
BLK
BLK
BLK
RIGHT
COMPRESSOR
BARREL
4
DEFROST
SOLENOID
BLK
BARREL
1
SYR.SOL.
WHT
ORG/WHT
J16
7 6 5 4 3 2 1
BLK
BLK
J2
RED
BRN.
BARREL 2
SYRUP OUT
SWITCH
1 2 3 4 5 6 7 8
J3
RED/BLK
LEFT INTERFACE PCB A.
1
L2
2
BARREL
1
H20 SOL.
ORN
J15
7 6 5 4 3 2 1
3
J4
J11
W2
1 2 3 4
J5
1 2 3 4 5 6 7 8
J7
4 3 2 1
4 3 2 1
5
6 5 4 3 2 1
WHT
BLU/WHT
J6
T2
BLK
PRP/WHT
1. STATIC ELECTRICITY MAY CAUSE
DAMAGE TO SOLID STATE COMPONENTS.
ELIMINATE STATIC ELECTRICITY BY TOUCHING
GROUNDED UNIT BEFORE HANDLING SOLID STATE
COMPONENTS.
2. STRIPED WIRE ON RIBBON CABLES MUST BE
CONNECTED TO PIN 1 AT EACH END.
RIGHT COMPRESSOR
CONTACTOR
12
LEFT
COMP.
CONT.
COIL
BLU
BLU
BLK
RED
BLK
BARREL
1
HOPPER
FILL
SWITCH
M
LEFT COMPRESSOR
CONTACTOR
WHT
NOTE:
1
BARREL
1
LIQ. LINE
SOLENOID
PRP/WHT
WHT
RED/WHT
BRN
BLK
BLK
BRN
BLK
BRN
BLK
RED
BLK
BLK
RIBBON CABLE
BARREL 1
BIB SWITCH
BLK
BLK
T1
LEFT
COMPRESSOR
W1
WHT
BRN
BLK
S
LEFT COMPRESSOR
CONTACTOR
L1
BRN
BARREL 1
SYRUP OUT
SWITCH
BARREL 1
BARREL 2
RIBBON CABLE SEE NOTE 2
RIBBON CABLE SEE NOTE 2
RIBBON CABLE SEE NOTE 2
BARREL
1
DEFROST
SOLENOID
BRN
ORN
ORG/WHT
BRN
THERMISTORS
PROBES
2
RELAY
WHT
WHT
LCD DISPLAY
LEFT
HPCO
PROXIMITY
SWITCH
YEL
BRN
11
L1
BLK
5
BRN
BLK/WHT
SERVICE/TEST ONLY
EMPTY-(RESERVED)
EMPTY-(RESERVED)
EMPTY-H2O PRESSURE SWITCH ACTIVE/JUMPER-H2O PRESSURE SWITCH BYPASSED
EMPTY-(JUMPER USED FOR DUAL BARREL DEFROST ONLY)
EMPTY-(RESERVED)
ORN
BARREL 4
KEYPAD
J7
BLK
RED
BARREL 2
BLK
BRN
RED/WHT
BARREL 2
KEYPAD
J1
1 2
BLK
BLK
YEL
RIGHT
BEATER
MOTOR
(SEE FIG 1)
WHT
L2
CONTROL
ENCLOSURE(S)
349
053636-27S
11/12/13
1
WHT
WHT/BLK
5
2
3
1
5
1
P1 OR PUR
THERMAL OL
T5 OR BLK
T1 OR BLU
BRN
A
4
WHT
YEL
WHT/BLK
2
FIG.1
WHT
GROUND FRAME
SECURELY
1/2 HP GE/RBC
1
WHT/BLK
YEL
3
WHT
WHT/BLK
1
2
P2 OR BRN
T8 OR RED
T4 OR YEL
4
LEESON
BEATER MOTOR WIRING
YEL
2
1/4 HP GE/RBC BEATER MOTOR WIRING
CWLE-RED OR T8 INTERNAL ON #A, BLACK OR T5 INTERNAL ON #5
6
MAGNATEK-CENTURY
YEL
BLK
BLK
BARREL 1
BLK
BLK
11
1
3
5
7
9
1 2 3 4
BARREL 3
KEYPAD
J9
RIBBON
UNIVERSAL PCB A.
CABLE
INTERNAL OVERLOAD
WHT(120 VOLTS)
BLK(230 VOLTS)
WHT
C
YEL
1
2
4
6
8
10
START
CABLE
4
RUN CAPACITOR
1 2 3 4
BARREL 3
BLK
RIBBON CABLE
BARREL 1
KEYPAD
LINE
EQUIPMENT
GROUND
R
WHT/BLK
MAIN
CABLE
15A FUSE
WHT
BLK
WHT
BLK
ORG
PRP/WHT
RED/WHT
LEFT INTERFACE PCB A. W1 JUMPER BLOCK DETAIL
(RIGHT INTERFACE PCB A. WI JUMPERS NON-FUNCTIONAL)
12
BLK
YEL
BLU
BLEED RESISTOR
BLK/YEL
J10
J9
J8
YEL
BLK
ORG
BRN
WHT/BLK
BLK
BLK
BLK
RIBBON
WHT/BLK
WHT/BLK
WHT/BLK
CABLE
15A FUSE
WHT
WHT
BRN
RIBBON
COPELAND COMPRESSOR WIRING
BLK
CABLE
J4
START CAPACITOR
BLK
BRN
WHT/BLK
J10
J9
J8
RIBBON
J3
BARREL 4
BLK
J11
J10
RIBBON
J6
J5
J2
WHT/BLK
YEL
BLK
BLK
M
CARB.
PUMP
BARREL
2
SYR.SOL.
WHT
BRN
BLK
BARREL
2
CO2 SOL.
BLK
BARREL
2
DEFROST
SOLENOID
YEL
RED/BLK
BARREL 2
LED
CONTROL
SWITCH
BLK
BARREL 1
LED
RED
WHT
WHT
BLK
LEFT BEATER
MOTOR
(SEE FIG 1)
L1 LINE L2
EMI FILTER
L1 LOADL2
PRIMARY
CONT.
TRANS.
RED
BLU
SECONDARY
WHT
OUT
OUT
BLK
BARREL 3
BARREL 4
RED/WHT
RED
BLU
BLK
BLK
BLK
BLK
BLK
BLU
BLU
BRN
BARREL
3
H20 SOL.
ORN
BARREL
3
SYR.SOL
ORG/WHT
WHT
7 6 5 4 3 2 1
BLU/WHT
WHT
6 5 4 3 2 1
WHT
BARREL
3
CO2 SOL.
7 6 5 4 3 2 1
RED
J16
1
BLK
BLK
RED/BLK
J3
1 2 3 4 5 6 7 8
M
BLOWER
BLK
BLK
W1
BLK
4
BARREL
4
DEFROST
SOLENOID
BARREL 4
LED
BARREL
4
CO2 SOL.
BLK
YEL
WHT
WHT
BARREL
4
SYR.SOL.
RUN CAPACITOR USED WITH
46536-27 MOTOR ONLY
BLK
BLK
BARREL
4
H20 SOL.
WHT
ORG/WHT
WHT
BRN
RED/WHT STR
1
BLK
BLK
WHT/BLK
H2O
PRESSURE
SWITCH
BARREL 3
LED
BARREL
4
HOPPER
FILL
SWITCH
B
J14
X1
J13
7 6 5 4 3 2 1
A
PRP/WHT
PRP
1 2
J1
RED/BLK
BLK
L2
BARREL
4
BIB
SWITCH
RED
BLK
T2
L3
RIGHT COMPRESSOR
CONTACTOR
T3
RIGHT COMPRESSOR
CONTACTOR
BLK
BLK
BLK
J2
BRN
BARREL 4
SYRUP OUT
SWITCH
M
RIGHT
COMPRESSOR
WHT
WHT
L2
BARREL
4
LIQ. LINE
SOLENOID
J12
7 6 5 4 3 2 1
BLU
L1
BRN
RIGHT INTERFACE PCB A.
3
J4
J15
5
J11
W2
1 2 3 4
J5
4
CO2
PRESSURE
SWITCH
BLK
BLK
1 2 3 4 5 6 7 8
J7
4 3 2 1
1 2 3 4
BLK
BARREL
3
HOPPER
FILL
SWITCH
RED
J6
PRP/WHT
RIGHT
COMP.
CONT.
COIL
WHT
WHT
RIBBON CABLE
SEE NOTE 3
BRN
BRN
RIBBON CABLE SEE NOTE 3
BLU
RED
BRN OUT
PCB A.
IN
IN
BARREL
BARREL
3
3
LIQ. LINE
DEFROST
SOLENOID SOLENOID
RED
BLU
PROXIMITY
SWITCH
BLK
BARREL 3
BIB SWITCH
1
T1
2
1
11
2
12
YEL
WHT
BLK
WHT
J14
7 6 5 4 3 2 1
J13
WHT
BARREL
2
H20 SOL.
CARB. FILL SWT
BARREL
2
LIQ. LINE
SOLENOID
L2
X1
BLU
BARREL 3
SYRUP OUT
SWITCH
BLK
L1
12
BLK
WHT
BARREL
1
CO2 SOL.
7 6 5 4 3 2 1
J12
W1
A
BLK
RIBBON CABLE
WHT
BARREL
1
SYR.SOL.
ORG/WHT
WHT
7 6 5 4 3 2 1
L1
BLK
1 2
J1
RED/BLK
J2
B
RIGHT
HPCO
BRN
BLK
1
CABLE
BRN
11
L1
BARREL 2
BLK
BLK
ORN
7 6 5 4 3 2 1
J16
BLK
1 2 3 4 5 6 7 8
J3
RED/BLK
LEFT INTERFACE PCB A.
1
RED
BLK
BARREL
2
HOPPER
FILL
SWITCH
WHT/BLK
BLK
RIGHT COMPRESSOR
CONTACTOR
BLK
RED/WHT
BARREL
1
H20 SOL.
WHT
6 5 4 3 2 1
3
J4
J15
W2
1 2 3 4
J5
1 2 3 4 5 6 7 8
J7
4 3 2 1
4 3 2 1
5
J11
BLU/WHT
J6
BLK
BARREL
2
BIB
SWITCH
RED
BLK.
RIBBON CABLE
BLK
NOTE:
RIGHT
BEATER
MOTOR
(SEE FIG 1)
L2 L3
WHT
BLK
CONTROL
ENCLOSURE(S)
GROUND FRAME
SECURELY
BLK
BLK
LEFT
COMP.
CONT.
COIL
BLU
BLU
PRP/WHT
BARREL 2
SYRUP OUT
SWITCH
BRN.
BLK
BLK
BLK
BLK
1. COMPRESSOR PROTECTED UNDER
PRIMARY SINGLE PHASING CONDITIONS.
2. STATIC ELECTRICITY MAY CAUSE
DAMAGE TO SOLID STATE COMPONENTS.
ELIMINATE STATIC ELECTRICITY BY TOUCHING
GROUNDED UNIT BEFORE HANDLING SOLID STATE
COMPONENTS.
WHT/BLK
BARREL
1
LIQ. LINE
SOLENOID
BLK
BLK
RED
L2
WHT
RED/WHT
LCD DISPLAY
BARREL
1
DEFROST
SOLENOID
PRP/WHT
WHT
RED/WHT
RIBBON CABLE SEE NOTE 3
RIBBON CABLE SEE NOTE 3
RED
BLK
BRN
BRN
RIBBON CABLE SEE NOTE 3
BARREL 2
BARREL 1
BRN
BLK
BLK
BARREL
1
HOPPER
FILL
SWITCH
T2
BLK
WHT
BRN
THERMISTORS
PROBES
YEL
BLK
BLK
BLK
BARREL 1
PROXIMITY
SWITCH
BLK
BARREL 1
BIB SWITCH
BLK
L3
WHT
WHT
WHT
BARREL 4
KEYPAD
CABLE
J7
RED
BARREL 1
SYRUP OUT
SWITCH
BLK
BLK
M
LEFT COMPRESSOR
RIBBON CABLE
BLK
ORN
ORG/WHT
BROWN
BARREL 2
KEYPAD
RIBBON
BLK
BLK
BARREL 3
KEYPAD
J9
RIBBON
BLK
YEL
LEFT
HPCO
BRN
T1
15A FUSE
LEFT COMPRESSOR
CONTACTOR
T3
ORN
BARREL 1
KEYPAD
RIBBON
UNIVERSAL PCB A.
J1
1 2
BLK
L1
BLK
WHT/BLK
LEFT COMPRESSOR
CONTACTOR
BLK
PRP/WHT
3. STRIPED WIRE ON RIBBON CABLES MUST BE
CONNECTED TO PIN 1 AT EACH END.
349
053636-33S
11/12/13
1
WHT/BLK
5
T1 OR BLU
2
1
1
P1 OR PUR
2
1
A
BRN
WHT
WHT/BLK
P2 OR BRN
3
T5 OR BLK
THERMAL OL
T8 OR RED
T4 OR YEL
4
LEESON
FIG.1
4
2
3
1
WHT
WHT/BLK
WHT
YEL
WHT/BLK
2
1/2 HP GE/RBC
YEL
BEATER MOTOR WIRING
YEL
5
1/4 HP GE/RBC BEATER MOTOR WIRING
CWLE-RED OR T8 INTERNAL ON #A, BLACK OR T5 INTERNAL ON #5
6
WHT
MAGNATEK-CENTURY
YEL
MAIN
RED/WHT
SERVICE/TEST ONLY
EMPTY-(RESERVED)
EMPTY-(RESERVED)
EMPTY-H2O PRESSURE SWITCH ACTIVE/JUMPER-H2O PRESSURE SWITCH BYPASSED
EMPTY-(JUMPER USED FOR DUAL BARREL DEFROST ONLY)
EMPTY-(RESERVED)
START
1 2 3 4
ORG/WHT
1 2 3 4
BARREL 3
BLK
RIBBON CABLE
15A FUSE
WHT
BLK
YEL
BLK
LEFT COMPRESSOR
CONTACTOR
W1
1
3
5
7
9
11
BLK
CABLE
COMPRESSOR
TERMINALS
LINE
2
4
6
8
10
BLK/YEL
J10
J9
J8
CABLE
J4
BLK
BLK
BLK
BLK
BLK
ORG
BRN
WHT/BLK
WHT/BLK
WHT/BLK
WHT/BLK
YEL
BLK
ORG
WHT
WHT
BRN
LEFT INTERFACE PCB A. W1 JUMPER BLOCK DETAIL
RIGHT INTERFACE PCB A. W1 JUMPERS NON-FUNCTIONAL)
12
BLK
CABLE
COMPRESSOR WIRING
BLK
BRN
WHT/BLK STRIPE
J10
J9
J8
RIBBON
J3
BARREL 4
BLK
J11
J10
RIBBON
J6
J5
J2
YEL
BLK
BARREL
1
CO2 SOL.
2
12
YEL
YEL
CABLE
WHT
BARREL
3
DEFROST
SOLENOID
BLK
BARREL
3
SYR.SOL
WHT
ORG/WHT
WHT
BARREL
3
CO2 SOL.
J16
7 6 5 4 3 2 1
RED
L1
RED
M
SEE FIG 1
WHT
BLOWER
BARREL
4
LIQ. LINE
SOLENOID
J12
7 6 5 4 3 2 1
BLU
BLK
RED/BLK
J3
1 2 3 4 5 6 7 8
BLK
B
WHT
BLK
WHT
BRN
WHT
BARREL
4
CO2 SOL.
RED/WHT
WHT
BLK
BLK
BARREL 4
LED
RIGHT
BEATER
MOTOR
(SEE FIG 1)
BARREL 3
LED
YEL
WHT
BARREL
4
SYR.SOL.
GRN/YEL
BARREL
4
H20 SOL.
WHT
ORG/WHT
X1
J13
A
J14
7 6 5 4 3 2 1
1 2
J1
L2
W1
RED/BLK
J2
BLK
4
BLK
GRN/YEL
BLK
BLK
WHT/BLK
H2O
PRESSURE
SWITCH
3
BARREL
4
DEFROST
SOLENOID
WHT
N L2 L3
GRN/YEL
WHT
ORN
BARREL
3
H20 SOL.
WHT
BLU/WHT
WHT
PRP/WHT
RIGHT
COMP.
CONT.
COIL
WHT
J15
7 6 5 4 3 2 1
1
RIGHT INTERFACE PCB A.
3
J4
J11
5
6 5 4 3 2 1
W2
1 2 3 4
J5
1 2 3 4 5 6 7 8
J7
4 3 2 1
4 3 2 1
PRP/WHT
PRP
BARREL
4
HOPPER
FILL
SWITCH
1
START
GRN/YEL
GRN/YEL
BLU
RED
RED/WHT
BARREL
3
LIQ. LINE
SOLENOID
OUT
J6
BLK
BARREL
4
BIB
SWITCH
RED
BLK
BLK
L2
1
GRN/YEL
BLK
WHT
LEFT BEATER
MOTOR
(SEE FIG 1)
IN
OUT
BLU
BLU
RIBBON CABLE
SEE NOTE 3
BLK
BLK
BLK
BRN
BARREL 4
SYRUP OUT
SWITCH
T2
RIGHT COMPRESSOR
CONTACTOR
4
50/60 HZ
THERMAL
O.L.
WHT
M
WHT
BARREL
2
DEFROST
SOLENOID
RED
BLU
IN
BRN OUT
PCB A.
RED
BLU
BRN
BRN
RIBBON CABLE SEE NOTE 3
BARREL 4
BLK
BARREL 3
RED
BLK
BLK
CO2
PRESSURE
SWITCH
BLK
L3
5
BLK
BLK
GRN/YEL
BARREL
2
CO2 SOL.
WHT
YEL
WHT
PROXIMITY
SWITCH
BRN
BLK
BARREL
3
HOPPER
FILL
SWITCH
M
EXTRA
MAIN
2
2C
BLK
BLK
BLK
BARREL
2
SYR.SOL.
BRN
WHT
BLK
L1 LINE L2
L1 LOADL2
PRIMARY
SECONDARY
CONT.
TRANS.
BLU
YEL
BLK
RED
EMI FILTER
RED/BLK
BARREL 2
LED
CONTROL
SWITCH
BARREL 1
LED
RED
BLU
BLU
BLK
BLK
BARREL 3
BIB SWITCH
BLK
PRP/WHT
RIGHT COMPRESSOR
BLK
T3
6
208/240
RIGHT COMPRESSOR
CONTACTOR
BLK 60 HZ
RED 50 HZ
BRN
BRN
WHT COM
FIG. 1
GE MOTOR SCHEMATIC
BLK
BLK
CARB.
PUMP
WHT
BARREL
2
H20 SOL.
WHT
WHT
J13
X1
J14
7 6 5 4 3 2 1
A
RIBBON CABLE
BLK
BRN
BARREL 3
SYRUP OUT
SWITCH
4
15A FUSE
BLK
WHT
L2
RED/BLK
1 2
J1
B
RIGHT
HPCO
1
ORN
BLK
WHT
WHT
WHT
CARB.
FILL SWT
BARREL
2
LIQ. LINE
SOLENOID
J12
7 6 5 4 3 2 1
W1
1
BARREL
1
SYR.SOL.
WHT
ORG/WHT
L1
BLK
J2
BLK
BARREL
2
HOPPER
FILL
SWITCH
BLK
T1
RED/WHT
BLK
WHT
ORN
J16
7 6 5 4 3 2 1
BLK
1 2 3 4 5 6 7 8
J3
RED/BLK
LEFT INTERFACE PCB A.
1
BLK
BARREL
2
BIB
SWITCH
RED
BLK.
WHT/BLK
RIBBON CABLE
BLK
L1
RIGHT COMPRESSOR
CONTACTOR
BLK
CAP
1 2 3 4
BARREL
1
H20 SOL.
WHT
J15
7 6 5 4 3 2 1
3
J4
J11
W2
1 2 3 4
J5
1 2 3 4 5 6 7 8
J7
4 3 2 1
4 3 2 1
5
6 5 4 3 2 1
BLU/WHT
J6
11
BARREL 2
BLK
GRN/YEL
BLU
BLU
LEFT
COMP.
CONT.
COIL
BLK
BLK
RED
BRN.
BARREL 2
SYRUP OUT
SWITCH
BLK
WHT
THERMISTORS
PROBES
BARREL
1
LIQ. LINE
SOLENOID
BRN
L2
BLK
BLK
2
RIBBON
WHT
WHT
BLK
1. COMPRESSOR PROTECTED UNDER
PRIMARY SINGLE PHASING CONDITIONS.
2. STATIC ELECTRICITY MAY CAUSE
DAMAGE TO SOLID STATE COMPONENTS.
ELIMINATE STATIC ELECTRICITY BY TOUCHING
GROUNDED UNIT BEFORE HANDLING SOLID STATE
COMPONENTS.
NOTE:
BLK
3. STRIPED WIRE ON RIBBON CABLES MUST BE
CONNECTED TO PIN 1 AT EACH END.
ORG/WHT
12
CABLE
LCD DISPLAY
BARREL
1
DEFROST
SOLENOID
PRP/WHT
WHT
RED/WHT
RIBBON CABLE SEE NOTE 3
RIBBON CABLE SEE NOTE 3
BLK
BRN
RIBBON CABLE SEE NOTE 3
BARREL 2
BARREL 1
BLK
RED
BARREL
1
HOPPER
FILL
SWITCH
WHT
BARREL 4
KEYPAD
J7
PROXIMITY
SWITCH
BLK
BARREL 1
BIB SWITCH
BRN
BLK
T2
RED/WHT
SERVICE/TEST ONLY
GRN/YEL
BLK
WHT
BRN
EMPTY-(RESERVED)
EMPTY-(RESERVED)
1
J1
1 2
BLK
RED
BLK
BRN
BARREL 1
SYRUP OUT
SWITCH
BLK
BLK
LEFT COMPRESSOR
RIBBON CABLE
BLK
M
L3
LEFT COMPRESSOR
CONTACTOR
T3
WHT
WHT
BARREL 2
KEYPAD
BARREL 3
KEYPAD
J9
RIBBON
RED
BARREL 1
BLK
LEFT
HPCO
T1
15A FUSE
W1
1
ORN/WHT
1 2 3 4
EMPTY-H2O PRESSURE SWITCH ACTIVE/JUMPER-H2O PRESSURE SWITCH BYPASSED
EMPTY-(JUMPER USED FOR DUAL BARREL DEFROST ONLY)
EMPTY-(RESERVED)
11
L1
CABLE
J4
BARREL 3
BLK
RIBBON CABLE
BARREL 1
KEYPAD
RIBBON
UNIVERSAL PCB A.
CABLE
BLK
BLK
L1
LEFT COMPRESSOR
CONTACTOR
BLK/WHT
LEFT COMPRESSOR
CONTACTOR
GROUND FRAME
SECURELY
BLK
ORN
3
5
7
9
CONTROL
ENCLOSURE(S)
349
053636-58S
11/12/13
1
WHT/BLK
5
2
3
1
5
1
P1 OR PUR
THERMAL OL
T5 OR BLK
T1 OR BLU
2
1
A
BRN
WHT
WHT/BLK
P2 OR BRN
T8 OR RED
T4 OR YEL
4
LEESON
FIG.1
4
3
1
WHT
WHT/BLK
WHT
YEL
WHT/BLK
2
1/2 HP GE/RBC
YEL
BEATER MOTOR WIRING
YEL
2
1/4 HP GE/RBC BEATER MOTOR WIRING
CWLE-RED OR T8 INTERNAL ON #A, BLACK OR T5 INTERNAL ON #5
6
WHT
MAGNATEK-CENTURY
YEL
MAIN
ORG/WHT
BRN
11
START
WHT/BLK
WHT/BLK
ORG
WHT
BLK
ORG
PRP/WHT
LEFT INTERFACE PCB A. W1 JUMPER BLOCK DETAIL
RIGHT INTERFACE PCB A. JUMPERS NON-FUNCTIONAL)
BLK
YEL
COMPRESSOR
TERMINALS
2
4
6
8
10
12
BLK/YEL
J10
J9
J8
BLK
BRN
WHT/BLK
WHT/BLK
WHT/BLK
WHT/BLK
WHT
BLK
WHT
WHT
BRN
CABLE
LINE
BLK
YEL
COMPRESSOR WIRING
MAIN
BLK
BRN
WHT/BLK
J10
J9
J8
RIBBON
J3
BARREL 4
BLK
J11
J10
RIBBON
J6
J5
J2
L1
LCD DISPLAY
COMP.
CONT.
COIL
BARREL
1
H20 SOL.
BARREL
1
SYR.SOL.
WHT
ORG/WHT
BARREL
1
CO2 SOL.
1
RED/BLK
L1
L2
1 2
J1
RED/BLK
B
WHT
BARREL
2
H20 SOL.
J13
X1
PRP/WHT
BLK
PRP
C
NO
BARREL
2
BIB
SWITCH
BLK
A
J14
7 6 5 4 3 21
BARREL
2
LIQ. LINE
SOLENOID
J12
BLK
J2
RED
BRN
BLK
BARREL
2
SYR.SOL.
WHT
WHT
BRN
M
FAN
WHT
BLU
BARREL
2
HOPPER
FILL
SWITCH
BARREL
2
CO2 SOL.
BRN
RED
BARREL
2
DEFROST
SOLENOID
WHT
L1
L1
3
PRIMARY
2
WHT
L2
LOAD L2
IN
WHT
ORN
ORN
EMI FILTER
LINE
CONTROL SWITCH
SPST
BLK
BLK
BLK
SECONDARY
BLK/WHT
OUT
CONTROL
TRANSFORMER
BLK
WHT/BLK
WHT
IN
BRN OUT
PCB A.
OUT
BARREL 1
LED
FAN MOTOR
RUN CAPACITOR
(USED WITH AIR
COOLED UNITS ONLY)
YEL
BLK
BLK/WHT
4
H2O
PRESSURE
SWITCH
1
RED/WHT
BARREL 2
LED
WHT
15A FUSE
BLK
W1
7 6 5 4 3 21
WHT
BLK/WHT
J3
1 2 3 4 5 6 7 8
BRN
BARREL 2
SYRUP OUT
SWITCH
OPTIONAL
BLK
BLK
BARREL
1
LIQ. LINE
SOLENOID
J16
7 6 5 4 3 21
WHT
ORN
J15
7 6 5 4 3 21
3
J4
INTERFACE PCB A.
J11
W2
1 2 3 4
J5
1 2 3 4 5 6 7 8
J7
4 3 2 1
4 3 2 1
BLK
BLK
3
5
6 5 4 3 21
BLU/WHT
WHT
J6
RED
BLK
2
C02
PRESSURE
SWITCH
PRP/WHT
THERMISTORS
PROBES
BARREL
1
DEFROST
SOLENOID
PRP/WHT
WHT
SEE NOTE 2
RED/WHT
BLK
YEL
BLK
YEL
RIBBON CABLE
SEE NOTE 2
BLU
BLU
BARREL
1
HOPPER
FILL
SWITCH
BLK
BLK
SEE NOTE 2
BRN
BRN
BLK
BRN
NO
PRP
BARREL 2
SAMPLER SWITCH
(PUSHBUTTON-OPTIONAL)
OPTIONAL
GRN
P.O.P.
DISPLAY
BEATER MOTOR
WHT
WHT
BLK/WHT
BLK
WHT
WHT
CARBONATOR FILL SWITCH
BLK
WHT
M1
PUMP
6
N
(SEE FIG.1 IF REMOTE CARBONATOR)
BLK
LOW H2O PRESSURE
INDICATOR LIGHT
L2
BLK
BLK
BARREL 2
KEYPAD
J9
SEE NOTE 2
CONTROL PCB A.
RIBBON CABLE
RIBBON CABLE
BLK
C
BARREL
1
BIB
SWITCH
WHT/BLK
L2
RED/BLK
RED
BLK
BLK
T2
BLK/WHT
LINE
GE/RBC BEATER MOTOR WIRING
2. TO REVERS ROTATION INTERCHANGE RED (T8) AND
BLACK (J9-KC, KCR OR T5-KH) LEADS.
1
2
3
1
P2 OR BRN
T8 OR RED
T3 OR ORN
START CAP.
(KC MOT0R
ONLY), LEAD
T5 OR BLACK
CONNECTED
DIRECTLY TO SWT
FOR KH MOTORS
J12 OR PUR
T5 OR BLK
WHT/BLK
3
YEL
HIGH VOLTAGE CW ROTATION SHOWN
T4 OR YEL
T2 OR WHT
RUN CAP.
(WHEN SPEC.)
J11 OR BRN
T1 OR BLU
THERMAL PROTECTOR
6
WHT
B
5
P1 OR PUR
A
4
2
INT.
BRN
1
4
1
WHT
WHT/BLK
2
S
YEL
WHT/BLK
RUN CAPACITOR
LEESON
3
3. WHEN MORE THAN ONE CAPACITOR IS USED CONNECT
IN PARALLEL.
YEL
BRN
R
BLEED RESISTOR
BRN
BEATER MOTOR WIRING
MAGNATEK-CENTURY
WHT
2
C
INTERNAL OVERLOAD
5
1
RELAY
4
BLK
WHT
NOTE:
1. FOR LOW VOLTAGE REMOVE BROWN (P2) FROM TERMINAL #3
AND PLACE ON TERMINAL #5, REMOVE WHITE (T2) FROM TERMINAL #5
AND PLACE ON TERMINAL #2.
355/355A/356
052840-27
11/12/13
GROUND FRAME
SECURELY
COPELAND COMPRESSOR WIRING
START CAPACITOR
EQUIPMENT
GROUND
J9 OR BLK
RIBBON CABLE
J7
RED
BLK
BRN
M
3
1
WHT
GRN/YEL
M
START
BARREL 2
BLK
BARREL 1
SYRUP OUT
SWITCH
BRN
T1
2
GRN/YEL
BLK
CARBONATOR
PUMP
CCW ROTATION
FROM LEAD END
MAIN 2
BARREL 1
BLK
PROXIMITY
SWITCHES
YEL
OPTIONAL
L1
COMPRESSOR
CONTACTOR
RED/BLK
L1
BLK
H2O
PRESSURE
SWITCH
BLK
CARBONATOR
FILL SWITCH
MAIN 1
BRN
COMPRESSOR
BLU
WHT
WHT
1. STATIC ELECTRICITY MAY CAUSE
DAMAGE TO SOLID STATE COMPONENTS.
ELIMINATE STATIC ELECTRICITY BY TOUCHING
GROUNDED UNIT BEFORE HANDLING SOLID STATE
COMPONENTS.
RED
WHT
2. STRIPED WIRE ON RIBBON CABLES
MUST BE CONNECTED TO PIN 1
AT EACH END.
WHT/BLK
WHT/BLK
BARREL 2
BARREL 1
HPCO
BLK
BLK
BARREL 1
SAMPLER SWITCH
(PUSHBUTTON-OPTIONAL)
BLK
COMPRESSOR
CONTACTOR
PRP/WHT
ORN
ORN/WHT
BRN
NOTE:
BRN
BLK
J1
1 2
EMPTY
RED
BARREL 1
KEYPAD
SEE NOTE 2
ORG/WHT
1 2 3 4
BLK
WHT
BRN
J11
J10
WHT
WHT
WHT
WHT
WHT
BLK
SEE NOTE 2
EMPTY
SERVICE/TEST ONLY
WHT/BLK
J10
J9
J8
RIBBON CABLE
EMPTY
EMPTY
EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED
BLK/YEL
2
1
3
5
BLK
12
7
9
RIBBON CABLE
INTERFACE PCB A. W1 JUMPER BLOCK DETAIL
REMOTE CARBONATOR WIRING 115V
FIG. 1
WHT
RED
1
2
4
6
11
BLK
J4
J6
J3
J5
J2
JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED
AS A MODEL 355, AIR COOLED WITH A H20 PRESSURE SWITCH.
BLK
WHT
BLK
YEL
BLK
BRN
11
8
10
W1
12
BLK
GRN/YEL
BARREL
1
SYR.SOL.
BARREL
1
CO2 SOL.
L1
15A FUSE
BLK
L2
J2
J14
B
WHT
BARREL
2
H20 SOL.
J13
X1
PRP/WHT
BLK
PRP
C
NO
BARREL
2
BIB
SWITCH
BLK
A
RED
1 2
J1
RED/BLK
7 6 5 4 3 21
BARREL
2
LIQ. LINE
SOLENOID
J12
W1
7 6 5 4 3 21
WHT
BLK/WHT
BLK
2
BARREL
1
H20 SOL.
ORG/WHT
WHT
RED/BLK
J3
1 2 3 4 5 6 7 8
WHT
BRN
BLK
BARREL
2
SYR.SOL.
WHT
WHT
BRN
M
FAN
WHT
BLU
BARREL
2
HOPPER
FILL
SWITCH
BARREL
2
CO2 SOL.
BRN
BARREL
2
DEFROST
SOLENOID
L1
L1
3
PRIMARY
2
WHT
L2
LOAD L2
IN
WHT
ORN
ORN
EMI FILTER
LINE
CONTROL SWITCH
SPST
BLK
BLK
BLK
SECONDARY
BLK/WHT
OUT
CONTROL
TRANSFORMER
WHT
IN
BRN OUT
PCB A.
OUT
BARREL 1
LED
FAN MOTOR
RUN CAPACITOR
USED WITH AIR
COOLED UNITS ONLY
YEL
BLK
BLK/WHT
BARREL 2
LED
RED
4
H2O
PRESSURE
SWITCH
1
WHT/BLK
BLK
BLK
OPTIONAL
GRN
P.O.P.
DISPLAY
BEATER MOTOR
WHT
WHT
BLK/WHT
BLK
WHT
WHT
M1
PUMP
6
(SEE FIG.1 IF REMOTE CARBONATOR)
CARBONATOR FILL SWITCH
L2 L3
BLK
BLK
BLK
COMP.
CONT.
COIL
WHT
ORN
1
BARREL 2
SYRUP OUT
SWITCH
WHT
WHT
THERMISTORS
PROBES
BARREL
1
LIQ. LINE
SOLENOID
WHT
J16
7 6 5 4 3 21
BLU/WHT
J15
7 6 5 4 3 21
J4
3
12
SEE NOTE 2
RED
BLK
INTERFACE PCB A.
J11
5
6 5 4 3 21
W2
1 2 3 4
J5
1 2 3 4 5 6 7 8
J7
4 3 2 1
4 3 2 1
BLK
BLK
PRP/WHT
OPTIONAL
BRN
PRP
BARREL 2
SAMPLER SWITCH
(PUSHBUTTON-OPTIONAL)
RED/BLK
LCD DISPLAY
BARREL
1
DEFROST
SOLENOID
BLU
J6
BLK
RED
C02
PRESSURE
SWITCH
3
L3
L1
BLK
2
1
3
GE/RBC BEATER MOTOR WIRING
2
3
1
P2 OR BRN
T8 OR RED
T3 OR ORN
START CAP.
(KC MOT0R
ONLY), LEAD
T5 OR BLACK
CONNECTED
DIRECTLY TO SWT
FOR KH MOTORS
J12 OR PUR
T5 OR BLK
5
P1 OR PUR
A
4
3
2
INT.
BRN
1
4
1
N
WHT
WHT/BLK
2
LEESON
WHT
WHT
GRN/YEL
M
YEL
WHT/BLK
WHT
NOTE:
1. FOR LOW VOLTAGE REMOVE BROWN (P2) FROM TERMINAL #3
AND PLACE ON TERMINAL #5, REMOVE WHITE (T2) FROM TERMINAL #5
AND PLACE ON TERMINAL #2.
2. TO REVERS ROTATION INTERCHANGE RED (T8) AND
BLACK (J9-KC, KCR OR T5-KH) LEADS.
1
WHT/BLK
3
YEL
HIGH VOLTAGE CW ROTATION SHOWN
T4 OR YEL
T2 OR WHT
RUN CAP.
(WHEN SPEC.)
J11 OR BRN
T1 OR BLU
THERMAL PROTECTOR
6
WHT
B
3. WHEN MORE THAN ONE CAPACITOR IS USED CONNECT
IN PARALLEL.
YEL
BLK
BEATER MOTOR WIRING
BLK
BLK
GRN/YEL
LOW H2O PRESSURE
INDICATOR LIGHT
BLK
CARBONATOR
PUMP
CCW ROTATION
FROM LEAD END
REMOTE CARBONATOR WIRING
FIG. 1
CARBONATOR
FILL SWITCH
BLK/WHT
MAGNATEK-CENTURY
H2O
PRESSURE
SWITCH
J9 OR BLK
PRP/WHT
BLK
BLK
BLU
BARREL
1
HOPPER
FILL
SWITCH
2
T3
START
WHT
BRN
BLK
BRN
BRN
SEE NOTE 2
SEE NOTE 2
SEE NOTE 2
RED/WHT
BLK
YEL
BLK
YEL
RIBBON CABLE
RIBBON CABLE
RIBBON CABLE
BLK
NO
BARREL
1
BIB
SWITCH
C
L2
WHT/BLK
T2
GROUND FRAME
SECURELY
MAIN 1
WHT
RED/BLK
1. STATIC ELECTRICITY MAY CAUSE
DAMAGE TO SOLID STATE COMPONENTS.
ELIMINATE STATIC ELECTRICITY BY TOUCHING
GROUNDED UNIT BEFORE HANDLING SOLID STATE
COMPONENTS.
MAIN 2
RED/WHT
2. STRIPED WIRE ON RIBBON CABLES
MUST BE CONNECTED TO PIN 1
AT EACH END.
BLK
BLK
BARREL 2
KEYPAD
RIBBON CABLE
CONTROL PCB A.
J9
RIBBON CABLE
J7
RED
BLK
PROXIMITY
SWITCHES
BARREL 1
SYRUP OUT
SWITCH
BRN
ORN
ORN/WHT
BRN
COMPRESSOR
CONTACTOR
WHT/BLK
WHT/BLK
BRN
COMPRESSOR
M
BLK
COMPRESSOR
CONTACT
BLU
WHT
NOTE:
RED
J1
1 2
BARREL 2
BARREL 1
HPCO
BLK
BRN
T1
PRP/WHT
BARREL 1
BLK
OPTIONAL
BARREL 1
SAMPLER SWITCH
(PUSHBUTTON-OPTIONAL)
L1
RED
YEL
EMPTY
EMPTY
EMPTY
EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED
EMPTY
SERVICE/TEST ONLY
BRN
BLK
WHT
BRN
1
RIBBON CABLE
ORG/WHT
1 2 3 4
BLK
WHT
WHT
WHT
WHT
WHT
BLK
BARREL 2
BLK
BLK
BLK
COMPRESSOR
CONTACTOR
WHT/BLK
SEE NOTE 2
INTERFACE PCB A. W1 JUMPER BLOCK DETAIL
GRN/YEL
BLK/YEL
J10
J9
J8
J11
J10
BARREL 1
KEYPAD
SEE NOTE 2
W1
1
3
5
7
9
11
BLK
J4
J6
J3
J5
J2
355/355A/356
052840-33
11/12/13
WHT
RED
11
2
4
6
8
10
12
BLK
JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED
AS A MODEL 355, AIR COOLED WITH A H20 PRESSURE SWITCH.
BLK
WHT
BLK
YEL
BLK
BRN
L1
BLK
COMP.
CONT.
COIL
BARREL
1
H20 SOL.
BARREL
1
SYR.SOL.
WHT
ORG/WHT
BARREL
1
CO2 SOL.
7 6 5 4 3 21
WHT
ORN
7 6 5 4 3 21
J4
3
1
RED/BLK
L1
L2
J2
1 2
J1
RED/BLK
BARREL
2
H20 SOL.
B
WHT
J14
X1
PRP/WHT
BLK
PRP
C
NO
BARREL
2
BIB
SWITCH
BLK
A
J13
7 6 5 4 3 21
BARREL
2
LIQ. LINE
SOLENOID
BLK
RED
BRN
BARREL
2
CO2 SOL.
BRN
BARREL
2
DEFROST
SOLENOID
L1
3
LINE
2
WHT
L2
LOAD L2
IN
GRN/YEL
WHT
ORN
ORN
EMI FILTER
L1
CONTROL SWITCH
SPST
BLK
BLK
BLK
PRIMARY
SECONDARY
BLK/WHT
OUT
CONTROL
TRANSFORMER
WHT
WHT/BLK
WHT
IN
BRN OUT
PCB A.
OUT
BARREL 1
LED
FAN MOTOR
RUN CAPACITOR
USED WITH AIR
COOLED UNITS ONLY
YEL
BLK
BLK/WHT
BARREL 2
LED
RED
4
H2O
PRESSURE
SWITCH
1
BARREL 2
SAMPLER SWITCH
(PUSHBUTTON-OPTIONAL)
PRP
BLK
BARREL
2
SYR.SOL.
WHT
BRN
WHT
M
FAN
WHT
BLU
BARREL
2
HOPPER
FILL
SWITCH
BLK
15A FUSE
BLK
W1
7 6 5 4 3 21
J12
WHT
BLK/WHT
J3
1 2 3 4 5 6 7 8
BARREL 2
SYRUP OUT
SWITCH
BRN
WHT
L2
WHT
2. STRIPED WIRE ON RIBBON CABLES
MUST BE CONNECTED TO PIN 1
AT EACH END.
P.O.P.
DISPLAY
OPTIONAL
GRN/YEL
BEATER MOTOR
WHT
WHT
GRN/YEL
BLK/WHT
GRN
WHT
WHT
GRN/YEL
BLK
6
M1
PUMP
(SEE FIG.1 IF REMOTE CARBONATOR)
CARBONATOR FILL SWITCH
GROUND FRAME
SECURELY
N
WHT
WHT
RED
BLK
OPTIONAL
WHT/BLK
T2
WHT
WHT
BLK
BARREL
1
LIQ. LINE
SOLENOID
WHT
6 5 4 3 21
J16
PRP/WHT
INTERFACE PCB A.
J15
W2
1 2 3 4
J5
1 2 3 4 5 6 7 8
J7
4 3 2 1
4 3 2 1
BLK
BLK
C02
PRESSURE
SWITCH
3
5
J11
BLU/WHT
J6
RED
BLK
BRN
COMPRESSOR
M
2
SEE NOTE 2
THERMISTORS
PROBES
BARREL
1
DEFROST
SOLENOID
PRP/WHT
WHT
SEE NOTE 2
SEE NOTE 2
RED/WHT
BLK
YEL
BLK
YEL
RIBBON CABLE
RIBBON CABLE
BLU
BLU
BLK
BARREL
1
HOPPER
FILL
SWITCH
BLK
BLK
SEE NOTE 2
BRN
BRN
BRN
BLK
NO
2
T1
12
J9
RIBBON CABLE
J7
C
BARREL
1
BIB
SWITCH
BLK
RIBBON CABLE
BRN
L1
RED/BLK
LCD DISPLAY
BARREL 2
KEYPAD
RIBBON CABLE
CONTROL PCB A.
J1
1 2
RED
BLK
PROXIMITY
SWITCHES
OPTIONAL
BRN
BLK
BARREL 1
SAMPLER SWITCH
(PUSHBUTTON-OPTIONAL)
RED/WHT
RED/BLK
1. STATIC ELECTRICITY MAY CAUSE
DAMAGE TO SOLID STATE COMPONENTS.
ELIMINATE STATIC ELECTRICITY BY TOUCHING
GROUNDED UNIT BEFORE HANDLING SOLID STATE
COMPONENTS.
GRN/YEL
WHT/BLK
WHT/BLK
ORN
ORN/WHT
BRN
COMPRESSOR
CONTACTOR
BLU
WHT
NOTE:
RED
BARREL 1
BLK
BARREL 1
SYRUP OUT
SWITCH
BLK
COMPRESSOR
CONTACTOR
PRP/WHT
BARREL 2
BARREL 1
HPCO
EMPTY
EMPTY
RED
YEL
EMPTY
SERVICE/TEST ONLY
BRN
BLK
WHT
BRN
1
RIBBON CABLE
ORG/WHT
1 2 3 4
BLK
WHT
WHT
WHT
WHT
WHT
BLK
SEE NOTE 2
INTERFACE PCB A. W1 JUMPER BLOCK DETAIL
6
4
LEESON
1
WHT
WHT/BLK
YEL
WHT/BLK
WHT
2
1
3
CONTROL
ENCLOSURE(S)
YEL
WHT
2
BLK
BRN
C
INTERNAL OVERLOAD
5
1
RELAY
4
BRN
S
R
BLEED RESISTOR
RUN CAPACITOR
BEATER MOTOR WIRING
MAGNATEK-CENTURY
EQUIPMENT
GROUND
2
3
1
BLK/WHT
BLK
WHT
WHT
GRN/YEL
M
N
CARBONATOR
PUMP
CCW ROTATION
FROM LEAD END
BLK
GRN/YEL
LOW H2O PRESSURE
INDICATOR LIGHT
BLK
COPELAND COMPRESSOR WIRING
START CAPACITOR
LINE
GRN/YEL
L1
BLK
H2O
PRESSURE
SWITCH
BLK
CARBONATOR
FILL SWITCH
REMOTE CARBONATOR WIRING
FIG. 1
GRN/YEL
WHT/BLK
BARREL 2
BLK
EMPTY
EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED
BLK/YEL
J10
J9
J8
J11
J10
BARREL 1
KEYPAD
SEE NOTE 2
W1
1
3
5
7
9
11
BLK
J4
J6
J3
J5
J2
355/355A/356
052840-40
11/12/13
WHT
RED
11
2
4
6
12
8
10
BLK
JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED
AS A MODEL 355, AIR COOLED WITH A H20 PRESSURE SWITCH.
BLK
WHT
BLK
YEL
BLK
BRN
L1
BLK
GRN/YEL
COMP.
CONT.
COIL
BLU
WHT
BARREL
1
CO2 SOL.
RED/BLK
L2
1 2
J1
RED/BLK
A
BARREL
2
H20 SOL.
B
WHT
J14
X1
J13
7 6 5 4 3 21
BARREL
2
LIQ. LINE
SOLENOID
WHT
BLK
J2
PRP/WHT
BLK
PRP
BLK
BLK
BARREL
2
SYR.SOL.
BRN
WHT
WHT
M
FAN
WHT
BLU
BARREL
2
HOPPER
FILL
SWITCH
BARREL
2
CO2 SOL.
BRN
BARREL
2
DEFROST
SOLENOID
L1
L1
3
PRIMARY
2
WHT
L2
LOAD L2
IN
WHT
ORN
ORN
EMI FILTER
LINE
CONTROL SWITCH
SPST
BLK
BLK
BLK
SECONDARY
BLK/WHT
BLK
OUT
CONTROL
TRANSFORMER
GRN/YEL
BLK
WHT/BLK
WHT
IN
BRN OUT
PCB A.
OUT
BARREL 1
LED
FAN MOTOR
RUN CAPACITOR
USED WITH AIR
COOLED UNITS ONLY
YEL
BLK
BLK/WHT
BARREL 2
LED
RED
4
H2O
PRESSURE
SWITCH
1
BARREL 2
SAMPLER SWITCH
(PUSHBUTTON-OPTIONAL)
PRP
15A FUSE
BLK
W1
7 6 5 4 3 21
J12
BLK/WHT
L1
J3
1 2 3 4 5 6 7 8
RED
NO
BARREL
2
BIB
SWITCH
C
WHT
P.O.P.
DISPLAY
BEATER MOTOR
RED/BLK
1. STATIC ELECTRICITY MAY CAUSE
DAMAGE TO SOLID STATE COMPONENTS.
ELIMINATE STATIC ELECTRICITY BY TOUCHING
GROUNDED UNIT BEFORE HANDLING SOLID STATE
COMPONENTS.
OPTIONAL
GRN/YEL
WHT
BLK/WHT
GRN/YEL
GRN/YEL
WHT
GRN/YEL
WHT
WHT
GRN
BLK
M1
PUMP
6
N
(SEE FIG.1 IF REMOTE CARBONATOR)
CARBONATOR FILL SWITCH
GROUND FRAME
SECURELY
L2 L3
BLK
BLK
BARREL
1
SYR.SOL.
1
WHT
BRN
RED/WHT
2. STRIPED WIRE ON RIBBON CABLES
MUST BE CONNECTED TO PIN 1
AT EACH END.
WHT
WHT
ORG/WHT
7 6 5 4 3 21
WHT
ORN
7 6 5 4 3 21
3
J4
BARREL 2
SYRUP OUT
SWITCH
OPTIONAL
WHT/BLK
BRN
L2
RED/BLK
BARREL
1
H20 SOL.
WHT
6 5 4 3 21
J16
BLK
INTERFACE PCB A.
J15
W2
1 2 3 4
J5
1 2 3 4 5 6 7 8
J7
4 3 2 1
4 3 2 1
BLK
BLK
5
J11
BLU/WHT
J6
BLK
RED
3
C02
PRESSURE
SWITCH
2
T2
BLK
BLK
BARREL
1
LIQ. LINE
SOLENOID
BLK
BLK
BLU
BLK
BARREL
1
HOPPER
FILL
SWITCH
BRN
COMPRESSOR
M
2
SEE NOTE 2
THERMISTORS
PROBES
BARREL
1
DEFROST
SOLENOID
PRP/WHT
WHT
BLK
BRN
BRN
SEE NOTE 2
SEE NOTE 2
SEE NOTE 2
RED/WHT
BLK
YEL
BLK
YEL
RIBBON CABLE
RIBBON CABLE
RIBBON CABLE
BLK
BRN
NO
BARREL
1
BIB
SWITCH
C
T1
ORN
ORN/WHT
BRN
12
J9
RIBBON CABLE
J7
RED
BLK
PROXIMITY
SWITCHES
BARREL 1
SYRUP OUT
SWITCH
BRN
L1
1
RIBBON CABLE
LCD DISPLAY
BARREL 2
KEYPAD
RIBBON CABLE
CONTROL PCB A.
J1
1 2
BARREL 2
BARREL 1
HPCO
BLK
BRN
BARREL 1
SAMPLER SWITCH
(PUSHBUTTON-OPTIONAL)
PRP/WH
COMPRESSOR
CONTACTOR
L3
WHT/BLK
WHT/BLK
BARREL 1
BLK
OPTIONAL
BLK
COMPRESSOR
CONTACTOR
BLK
T3
BLU
WHT
NOTE:
RED
WHT
WHT
COMPRESSOR
CONTACTOR
PRP/WHT
RED
RED
YEL
EMPTY
SERVICE/TEST ONLY
BRN
BLK
WHT
BRN
ORG/WHT
1 2 3 4
BLK
WHT
WHT
WHT
WHT
WHT
BLK
BARREL 2
BLK
EMPTY
EMPTY - H20 PRESSURE SWITCH ACTIVE/JUMPER - H20 PRESSURE SWITCH BYPASSED
EMPTY
EMPTY
WHT/BLK
SEE NOTE 2
INTERFACE PCB A. W1 JUMPER BLOCK DETAIL
L1
2
3
1
4
LEESON
1
WHT
WHT/BLK
YEL
WHT/BLK
WHT
2
1
3
CONTROL
ENCLOSURE(S)
6
BLK/WHT
BLK
WHT
WHT
GRN/YEL
M
N
CARBONATOR
PUMP
CCW ROTATION
FROM LEAD END
BLK
GRN/YEL
LOW H2O PRESSURE
INDICATOR LIGHT
BLK
BEATER MOTOR WIRING
MAGNATEK-CENTURY
YEL
GRN/YEL
BLK
H2O
PRESSURE
SWITCH
BLK
CARBONATOR
FILL SWITCH
REMOTE CARBONATOR WIRING
FIG. 1
GRN/YEL
BLK/YEL
J10
J9
J8
J11
J10
BARREL 1
KEYPAD
SEE NOTE 2
W1
1
3
5
7
9
11
BLK
J4
J6
J3
J5
J2
BLK
355/355a/356
052840-58
11/12/13
WHT
RED
11
2
4
6
8
10
12
BLK
JUMPER BLOCK SHOWN ABOVE WOULD INDICATE A UNIT CONFIGURED
AS A MODEL 355, AIR COOLED WITH A H20 PRESSURE SWITCH.
BLK
WHT
BLK
YEL
BLK
BRN
L1
BLK
GRN/YEL