Download Sioux Tools 5050AL User's Manual
Transcript
Form # Z356D Model 5050N5051 Al5050AL - Serial "C" 1/2" Pistol Grip Twin Hammer Imoact Wrenches Operator Instructions Important Read these instructions carefully before installing, operating, servicing or repairingthis tool. Keep these instructionsin a safe accessible place. - Includes Foreseen Use, Work Stations, Putting Into Service, Operating, Dismantling, Assembly and Safety Rules. Sioux Tools, Inc. 117 Levi Drive Murphy, NC 28906 U.S.A. Tel No. 828.835-9765 Product Net Weight 5050N5051A 5050AL 5.60 5.80 Ibs 2.50 2.60 Kq ProdudType 1/2" Pistol Grip Twin Hammer Impact Wrenches SAFETY MESSAGES 5050A Chrome Nose Case 5051A Black Nose Case 5050AL 2" Ext. Anvil Fax No. 828-835-9685 Recommended Hose Bore Recommended Use Of Balancer Or Support 6.2 6.2 A Size - Minimum 3/8ins 10mm Use - Safety Boots Use - Breathing Masks Use - Ear Protectors YES bar bar 90 90 PSI Test Method: Tested in accordance with Pneurop test code PN8NTC1 and I S 0 Standard 3744 PSI i WARNING Vibration Level (5050A15051 A) @ NGw-v Wear Hearing Protection YES A Recommended Max. Hose Length 30Ft 10M Noise Level: Sound Pressure Level 89.0 dB{A) Sound Power t-evet 100.0<tB{A) Always Read Instructions ~eforeusing -TOOIS Peisonaf Safety Equipment Use Safety Glasses Use Safety Gloves Serial No. Model No/Nos Air Pressure Recommended Working Maximum f (5050AL) 4.0 Meters 1 Sec2 4.3 Meters I Sec2 Test Method: Tested in accordance with I S 0 standards 8662 Parts 1 & 7 Amid Prolonged Exposure mmm Safety rules when using 5050A, 5051A and 5050AL Impact Wrenches - Use only impact sockets and extensions, universal joints, etc. rated as being suitable far use with impact wrenches. - Prolonged exposure to vibration may cause injury. -Read all instructions before using this toot. Ail operators must be fuHy trained in its use and aware of these safety rules. - Do not exceed the maximum working air pressure. - Use personal protection equipment as recommended. - Some dust created by power sanding, sawing, grinding, away from the working attachment fixed to the tool. -The tool is not electrically insulated. Never use the too) if there is any chance of coming into contact with live electricity. -Always when using the tool, adopt a firm footing and/or positionand grip the tool sufficiently only to overcome any reaction forces that may result from the tool doing work. Do not overgrip. -Use only correct spare parts for maintenance and repair. Do not improvise or make temporary repairs. Major servicing and repairs should only be carried out by persons trained to do so. -Do not lock, tape, wire, etc. the 'On/Off' valve in 'On' position. The trigger/lwer, etc. must always be free to return to the 'Off' position when released. drilling, and other construction activities contains chemicals known to cause cancer, birth defects and other reproductive harm. -Use only compressed air at the recommendedconditions. -If the tool appears to malfunction, ft! Pipa And Fittings remove from use immediately and swH bw arrange for service and repair. If it is not practical to remove too! from service, then shut off the air supply to the tool and write OF have written a warning note and attach it to the toot. - If tool is to be used with a balancer or other suspension device, ensure that the tool is firmly attached to the suspensiodsupport device. W h e n operating the tool, always keep the body and particularly the hands Recommended Air Supply System Page No 1 Figure 1