Download PASCO Specialty & Mfg. 648-06146 User's Manual
Transcript
012-12250A Instruction Sheet for the PASCO Model OS-8475 DIODE LASER FOR OPTICS SYSTEMS D IO D P E T L IC A S S S ER Y S F T O E R M ® S Introduction OS The magnetic steel base of the Diode Laser incorporates an “alignment edge” that, when placed against the alignment rail of your PASCO Optics System, aligns the laser beam to the optical path of your existing system’s components. The laser diode assembly can also be rotated 360° adding flexibility to experiment set up. See Figure 1. -84 75 O 650nm, <1mW CW (Red) A 25 S -85 TIC ER OS OPLAS SICDE BADIO D RE ® vd. USA ll Bl 7 othi . 9574 CA 1 Fo le, 1010 sevil Ro Notice No. 50, dated June 24, 2007 ED ITT EM RE T IS RTU IGH PE R L IS A SE TH LAROM F LASER LIGHT DO NOT STARE INTO BEAM Complies with FDA performance standards for laser products except for deviations pursuant to Laser Warning label located on Product CLASS 2 LASER PRODUCT 650nm, <1mW CW (Red) CLASSIFIED 60825-1 2007 Notice No. 50, dated June 24, 2007 Additional equipment recommended: – PASCO OS-8500 Introductory Optics System – PASCO OS-9250 Advanced Optics System (without laser) – PASCO OS-9251 Intermediate Optics System (without laser) thumbscrew Manufacture I.D. Label ED ITT EM RE T IS RTU IGH PE R L IS A SE TH LAROM F vd. USA ll Bl 7 othi . 9574 1 Fo , CA lle 1010 sevi Ro ® A 25 S -85 TIC ER OS OPLAS SICDE BADIO D RE “alignment edge” Figure 1: OS-8475 Diode Laser Features Equipment – 9VDC adapter Replacement parts: Description PASCO part no. thumbscrew assembly 617-008 Optics System mount 648-06146 CAUTION - use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. LASER LIGHT - DO NOT STARE INTO BEAM. – Diode Laser for PASCO Optics Systems. A S lvd. 7 U ill B 9574 ooth A 1 F ille, C 1010osev R Complies with FDA performance standards for laser products except for deviations pursuant to Laser CLASSIFIED 60825-1 2007 LASER LIGHT DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT M an uf ac tu re d by : The OS-8475 Diode Laser for PASCO Optics Systems is designed specifically as an integrated alternate light source for the PASCO OS-8500 Introductory Optics System. This accessory can also be used as an inexpensive light source option for PASCO OS-9250 (advanced) or OS-9251 (intermediate) Optics Systems. CLASS 2 LASER PRODUCT This Laser Product is designated as Class 2 during all procedures of operation. Do not point the laser or allow the laser to be directed or reflected toward people or animals. better 10101 Foothills Blvd. • P.O. Box 619011 • Roseville, CA 95678-9011 USA Phone (916) 786-3800 • FAX (916) 786-8905 • email: [email protected] ways to teach science Diode Laser for Optics Systems 012-12250A Specifications OS-8475 Laser Diode Divergence <2 mrd Beam Diameter at aparture 3 mm PASCO Introductory Optics bench (not included) Figure 2: Laser Diode Setup foPASCO Introductory Optics bench Assembly OS-8475 Laser Diode D OP IODE OS-8 TIC LA 475 S S SE YS R F Ro10101 sevil Fo TE OR le, othill CA Bl MS 9574 vd. 7 US A Ma nuf act ure d by: ®® 1. Determine the configuration of your experiment and the location in which the Diode Laser will be set up and adjust the orientation of the Diode Laser accordingly. Make sure the face of the laser diode assembly is relatively perpendicular to the surface of your optics bench. This will minimize the amount of fine adjustment you may need to perform in step 4. Tighten the thumbscrew to secure the laser diode module. 2. Place the “alignment edge” of the Diode Laser against the alignment rail of your PASCO optics bench. See Figures 2 and 3. 3. Plug the 9VDC adapter phone plug into the back of the laser and turn on the laser. 4. If necessary, use the adjustment screws to align the laser beam from left-to-right and up-and down. See Figure 4. 5. When using with the Laser Slits, OS-8529, slide the Laser Diode to the top of the slots on the mount A S REPEE D DD O IO F L OSDE IGH -847 LA T 5 SSPE ® RE ERE D DD O US A IO F L D OS E IGH 101 -847 LA T Ro 01 Foo sev thil ille l 5 SE ® , CA Blv R . 957d. 47 101 Ro 01 Foo sev thil ille l , CA Blv . 957d. 47 US A AV LA OID SE EX FR R LI PO OM GH SU TH T IS RE IS AP EM ER ITTE TU D RE AV LA OID SE EX FR R LI PO OM GH SU TH T IS RE IS AP EM ER ITTE TU D RE PASCO Advanced Optics bench (not included) Figure 3: Laser Diode Setup for PASCO Advanced Optics bench adjustment screws mount slots OP <1 mW R FO S 75 R M -84 SE ASTEER OS S S LA 8528Y S LA O EM DE OSS C ST DE DIO PTIDCIO PASS SY O TIC A 1 R 010 so e 1 F vil oo e, th CA il B 95 lvd 74 . 7 US : d by ture ufac Man Maximum Output ® 532 nm (green) 650 nm (red) HT IG R F L ASE D OE L EE D 5 SP DIOS-847 D O RE Wavelength RE SU TED PO EX EMITRE OID IS TU AV GHT ER R LI IS AP SE TH LA OM FR Class II Laser d. USA l Blv thil 95747 Foo . 01 , CA 101seville Ro Classification ® L TA ON RIZ ST HOADJU ON DE DIO m ER 0 n ER AS : 65 D L gth mW POW REvelen t: < 1 WaOutpu m 3.5m DC 9V L ICA RT T VE JUS AD OFF +9 VD GN C D mA 500 input jack (9VDC) Figure 4: Laser Beam Fine Adjustment 2 ® 012-12250A Diode Laser for Technical Support For assistance with any PASCO product, contact PASCO at: Address: PASCO scientific 10101 Foothills Blvd. Roseville, CA 95747-7100 Phone: 916-786-3800 (worldwide) 800-772-8700 (U.S.) Fax: (916) 786-7565 Web: www.pasco.com Email: [email protected] Copyright The PASCO scientific 012-09867A Basic Optics Diode Laser Instruction Sheet is copyrighted with all rights reserved. Permission is granted to non-profit educational institutions for reproduction of any part of this manual, providing the reproductions are used only in their laboratories and classrooms, and are not sold for profit. Reproduction under any other circumstances, without the written consent of PASCO scientific, is prohibited. Trademarks PASCO and PASCO scientific are trademarks or registered trademarks of PASCO scientific, in the United States and/or in other countries. All other brands, products, or service names are or may be trademarks or service marks of, and are used to identify, products or services of, their respective owners. For more information visit www.pasco.com/legal. Limited Warranty For a description of the product warranty, see the PASCO catalog. _______________________________________________________ ___ ➧ NOTE: NO service or maintenance is allowed, on this product, by the customer. Return unit to the factory for service or repair. Unit is NOT to be opened or modified by the Customer. _______________________________________________________ ___ ® Optics Systems 3 Diode Laser for Optics Systems 012-12250A Notes: 4 ®