Transcript
T READAND UNDERSTANDTHESEINSTRUCTIONSBEFOREINSTALLINGFIXTURE lNSTRUCTION SHEET NO, hisfktureisintended for installation in ectordanse with the National Eladricd Code end Id rsgulatbna, o sssurs full sompfianca with Ixal OxJes snd rsgule.tkma,c+@ with your Ixd e!ectriral ins@or Lwfora wtallation. To prevent eleotrfd sheck, turn off elacbiciy at fuss box before premsding. Retsinthese instructionsfor maintenancereferenoe. IS:40719 Pegelofl AND ASSEMBLY OF RADIANCE STEM EXTENSION KITS INSTRUCTIONS FOR INSTALLATION CAUTION: BE CAREFUL WHILE HANDLING FIXTURE WIRES. DO NOT DAMAGE WIRE INSULATION OR PINCH WIRES BETWEEN PARTS. 1. Unps& CENTER STEM ASSEMBLY (supplisd with f~re) snd cmefuliy until FIXTURE WIRES. 2. Gent~ pull downward en CANOPY to disengege fmm CROSSBAR SPRING CLIPS and expmw CROSSBAR (fig, 1), 3. Remove the two SCREWS from beth sides d SWIVEL CASTING snd skfe SWIVEL PIN oul fmm one d the holse in the SWIVEL CASTING (Fig, 1). NOTE A small smswddver may be required to push SWIVEL PINoutthroughtie hob in SWIVELCASTING, CAUTION: ASSEMBLY PLACE SCREWS AND OF EXTENSION SWIVEL PIN IN A SAFE PLACE; THESE PARTS ARE NEEDED FOR FINAL KIT. 4. While holding CENTER STEM ASSEMBLYsnd FIX7UREWIRES, genttfslikieSWlVELCASTlNGfCRQ3SsARAs3EMBLYup FIXTURE WIRES UnfiIA~EMBLY ISmmpletely rsmoved fmm FIXTURE WIRES (Fig. 2), Plain SWIVEL CASTING/CROSSBAR ASSEMBLY ins safe place. donotslideupinsideSTEM, NOTE Make owtsin QUICK CONNECTORS at the lower endofCENTERSTEMAS3EMSLY FIXTURE WIRES (UN.COILED) FIXTURE WIRES CROSSBAR CROSSBAR SPRING CLIPS SWIVEL CASTING ZSP’N SWIVEL CASTING[ CROSSBAR ASSEMBLY CENTER STEM ASSEMBLY [SUPPLIED WITH FIXNREI 7 SCREWS CENTER STEM ASSEMBLY CANOPY FIG,1=, I FI 5. Pass FIXTURE WIRES through EXTENSION STEM COLIAR and EXTENSION STEM and slide EXTENSION STEM dewn FIXTURE WIRES until EXTENSION STEM COL~R meets CENTER STEM AssEMSLY (Fig. 3A), 6. Aligning the holes in the side of CENTER STEM ASSEMBLY WW tie UWSSCIWh~l~ in EXTENSION STEM COLIAR, SIIW COMR to side in~~e CENTER STEM ASSEMBLY and secure in place by installing the two screws providwJ whh EX7ENSION STEM KIT (fig, 3S), NOTE Before preceedin~ repeat steps 5 snd 6 f a ssmnd EXTENSION STEM KIT is to b used, 7. Re.sssemble SWIVEL CASTING/CROSSBAR ASSEMSLY te the end of WENSION STEM by reveming steps 3 snd 4 above (Fig. 4), 8. Continue FIXTURE insfsllation by following instructions supplisd with FIXTURE, NOTE FIXTURES are supplied with enough FIXTURE WIRE 10allow two EXTENSION STEM KITS to be insfsllsd. If only one EXTENSION KIT is uset excass FIXTURE WIRES should be cut off making certain Mere is a minimum of 6’ of FIXTURE WIRE sbeve CROSSBAR ASSEMSLY for OUTLET BOX WIRING, ‘:’: 1.1<> 4=-:s:: l-l-i-c> 1.1 E la” %R%,gwywu’ —
