Download Liebert IntelliRack User's Manual
Transcript
INTELLIRACK Description The IntelliRack is a powerful multiplexing device that allows a Liebert UPS of any size to communicate with a virtually unlimited number of computers. The IntelliRack unit has five Intellislots for MultiPort 4 cards that can be connected to as many as four computers each. An IntelliRack unit with five MultiPort 4 cards installed will notify up to 20 computers of power failure and low battery conditions. A built-in bridging capability permits daisychaining IntelliRack units together, accommodating a virtually unlimited number of computers— limited only by the capacity of the UPS. When a power failure or low battery arises in the UPS, the IntelliRack sends notifications to all systems connected to the IntelliRack. One example of a connected system is a network of computers running Liebert’s MultiLink™ shutdown software. For other applications, contact your local Liebert representative or call 1-800-222-5877. FRONT VIEW BACK VIEW — + Bridging EMERSON Power Network UPS OUT IN Low Transmit Receive AC (RX) Fail Battery (TX) Power Inputs: 12 V DC 1.5A Power Connect Screw to UPS holes Connect for rack to other mounting IntelliRack brackets units UPS warning indicators (red) IntelliRack Redundant Power MultiPort4 Power connectors and indicators (green) Features and Benefits • • • • • • • • • • • • 4 1U Rack Space 19" or 23" Rack Mounting Brackets Dual Power Supply Inputs Universal Power Supply Modular and Scalable Dedicated Communications from UPS to Each Computer LED Notification Multiple Operating System Support Daisy-Chain Modules Integration with MultiLink Automated Shutdown Software Unlimited Number of Computer Systems Connects to all Liebert UPS systems SL-31094 Product Specification/Installation Sheet 3 2 Slots 2-5 for additional cards (shown with covers) 1 Slot 1 (shown with MultiPort 4 card installed) Specifications Power Requirements 12VDC ±10% of nominal; (2 inputs) 50/60 Hz, 1.5A, 18VA Dimensions 16 x 9 x 1.66 W x D x H, in. (mm) (406.4 x 228.6 x 42.2) Weight 9.9 lbs. (4.5 kg) Mounting 19" or 23" rack mount or 23" desktop Ambient Operating 32ºF to 104ºF (0ºC to 40ºC) Environment 0% RH to 95% RH (non-condensing) Agency Listings UL None CSA None CE None FCC Compliance None Communication Ports (Quantity) DB9 (1) To UPS; uses adapters (included) Bridges multiple IntelliRacks together; RJ45 (2) uses RJ45 cables (included) Intellislots (5) Hot-swappable ports page 1 2/04 (Rev. 0) Hardware and Components IntelliRack S ON EMER Power Network UPS OUT IN Low Trans mit R eceive AC (R X) Fail Battery (TX) Universal power supply — + Bridging Power Inputs 12 V DC 1.5A : Power IntelliR ack R edundant Power 120V or 230V power cord (120V shown) MP-ADP-02 adapter (DB9-to-RJ45) RJ45 cable (2 provided) Connect to UPS Bridging S ON EMER Power Network OUT IN Low Trans mit R eceive AC (R X) Fail Battery (TX) Power Inputs 12 V DC 1.5A Power MP-ADP-01 adapter (DB9-to-RJ45) Connects to UPS: either A or B below, depending on type of UPS A (for UPS with DB9 port) MP-ADP-01 connects to DB9 port of UPS UPS : IntelliR ack R edundant Power RJ45 cable (2 provided) Daisy-chain to another IntelliRack OR 120V or 230V power cord (230V shown) — + Universal power supply B (for UPS with no DB9 port) MP-ADP-01 adapter connects to open-wire adapter (SNS3ADPT, at left)* which connects to UPS * Item purchased separately Dimensions TOP VIEW SIDE VIEW 9" (228.6mm) 9" (228.6mm) 16" (406.4mm) 1.66" (42.2mm) FRONT VIEW 1.66" (42.2mm) 16" (406.4mm) Wiring Specifications Connection RJ45 cable to connect UPS to MultiPort RJ45 cable to connect Bridging Port MultiLink / AS400 cable Provided / Purchased Separately Maximum Length* 6 & 25 ft. (1.8 & 7.6m); 2 cables provided 300 ft. (91m) 10 ft. (3m); Purchased separately 100 ft. (31m) * For longer cables, refer to the IntelliRack user manual. Ordering Information Quantity Part # Description IntelliRack unit, two DB9-to-RJ45 adapters, two RJ45 cables, a universal power supply and two line cords (120V & 230V) IRACKUNIVPS Secondary power connection for the IntelliRack’s redundant port (requires 12VDC) MULTIPORT4 MultiPort 4 kit with one MultiPort 4 card and one molded cable assembly with four connectors IRACKMLADPT Liebert MultiLink Cable Adapter Kit with two DB9-to-RJ45 adapters INTELLIRACK SL-31094 Product Specification/Installation Sheet page 2 2/04 (Rev. 0)