Download American Standard ChinaLUX 120012.WHT User's Manual
Transcript
Two-Piece Toilets Two-Piece Toilets Elongated Front Toilet Models ❏ 1000EL.WHT and ❏ 1000EL.BON Round Front Toilet Models ❏ 1000RF.WHT and ❏ 1000RF.BON ❏ Bowl – White 1100EL.WHT ❏ Bowl – Bone 1100EL.BON ❏ Bowl – White 1100RF.WHT ❏ Bowl – Bone 1100RF.BON ❏ Tank – White 120012.WHT ❏ Tank – Bone 120012.BON ❏ Tank – White 120012.WHT ❏ Tank – Bone 120012.BON Nominal Dimensions: 29-1/4" x 19-7/16" x 26-7/8" (743 x 494 x 683mm) Nominal Dimensions: 27-1/4" x 19-7/16" x 26-7/8" (692 x 494 x 683mm) FINISHED WALL FINISHED WALL 27-1/4" (692mm) 29-1/4" (743mm) 1" ± 1/4" (25mm ± 6mm) 1" ± 1/4" (25mm ± 6mm) 19-7/16" (494mm) 8" (202mm) 16-1/2" (419mm) 18-1/2" (470mm) C/L OF SEAT POST HOLES 5-1/2" (140MM) CENTERS C/L OF SEAT POST HOLES 5-1/2" (140MM) CENTERS 3-1/4" (83mm) 14" (356mm) * 10" (254mm) 16mm (5/8) 12" (304mm) C/L OF OUTLET 12" (304mm) 14" (356mm) 14-5/8" (370mm) 6" (152mm) FINISHED FLOOR • Close-coupled, two-piece toilet • Fixture only, seat and supply by others • Vitreous china • 1.6 gallons (6 liters) of water per flush • 12" (305mm) rough-in • Available in Elongated and Round Front • Siphon vortex bowl • 14" (356mm) rim height • Fully glazed 2" trapway • 9" x 8-3/4" water surface area • Two color-matched bowl caps • One year limited warranty * 10" (254mm) 16mm (5/8) 6-7/16" (163mm) 9-7/8" (250mm) 26-7/8" (683mm) SUPPLY AS REQ’D 3-1/4" (83mm) 26-7/8" (683mm) SUPPLY AS REQ’D 7" (177mm) 19-7/16" (494mm) 8" (202mm) 12" (304mm) C/L OF OUTLET 12" (304mm) 15" (380mm) 6" (152mm) FINISHED FLOOR 9-5/8" (245mm) To Be Specified: Color: ❏ White ❏ Bone ❏ Supply with stop: _____________ Compliance Certifications – Meets or Exceeds the Following Specifications: • ASME A112.19.2M for Vitreous China Fixtures – includes Flush Performance, Ball Pass Diameter, Trap Seal Depth and all Dimensions NOTES: THIS COMBINATION IS DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF 305MM (12") FROM FINISHED WALL TO C/L OF OUTLET. * DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED. SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY. IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerance established by ANSI Standard A112.19.2 These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages. Revised 10/08