Download HSM Shredstar MS12C

 IMPORTA
ANT SAFETY NOT
TES
Turn off and unplu
ug the shredder beffore moving, emptying the waste
bin, or if the shredder will not be used
d for a long period of
o time.
Keep children and pets away from sh
hredder.
Do not place fingers, hands or any fo
oreign objects in the
e feed slot.
Serious injury may
y result.
Shred only one cre
edit card at a time.
Keep ties, jewelry, hair and loose clotthing away from the
e feed slot.
Serious injury may
y result.
Do not use canned
d air on shredder. Never use aerosol,, petroleum
based or other flam
mmable products on or near shredde
er.
Do not exceed the
e recommended pap
per capacity of 12 sheets.
s
One folded sheet of
o paper equals 2 sheets.
s
An occasio
onal paper
clip or metal staple
e is allowed.
Shred only one CD
D, DVD at a time.









D
Do not shred envelo
opes or labels with a sticky substance
e like glue. Do not
sshred wet paper, ca
arbon paper or viny
yl bags. The shred will stick in the
ccutters and may cause paper jams or lower shredding pe
erformance.
E
Empty the wasteba
asket regularly to prrevent paper jams.
D
Do not operate if th
he power cord appe
ears damaged. Do not alter this unit or
o
ccord in any way.
D
Do not place this sh
hredder near waterr or any heat source
e. Keep 6 inches
a
away from wall.
D
Do not use any oil or
o lubricants not cle
early specified for shredder
s
use in or
a
around this unit. So
ome agents may co
ombust causing serious injury.
If an extension cord
d is used, make surre that the total ampere ratings of the
p
products plugged in
nto the extension co
ord do not exceed the
t extension cord
a
ampere rating, and that the total of all products plugged into
i
the wall outlet
d
does not exceed 15
5 amps.
T
This shredder shou
uld be used only witth an operator in attendance. Keep
sshredder in the ON/OFF position and unplug from the AC
C outlet when not in
n
u
use for an extended
d period of time.
A
Avoid exposing the shredder to direct sunlight.
C
Clean the bin after shredding approxim
mately 60-70 sheets of paper.
TECHN
NICAL DATA
Part Number:
y Level:
Security
Shred Size:
S
Throat:
Maximu
um Capacity:
Shred Bin
B Capacity:
Voltage
e:
Noise le
evel:
Weight:
Duty cycle:
HSM1055
3
5/32" x 1 3/8" (4 x 35mm)(cross cut)
8.6” (218 mm)
12 sheets
2.1 gallons (7,9 litters)
115 V/60 Hz 58 dB 18 lbs. (8,2 kg)
minutes off
5 minutes on/30 m
LLATION:
INSTAL
-Unpack
k and set the machhine upright on leve
el surface.
-Make sure
s
the waste bin iis properly inserted
d into the shredder cabinet.
-Plug in the machine. Seee “TECHNICAL DAT
TA” for necessary p
precautions.
-The ou
utlet should be instaalled near the equip
pment and be easilyy accessible.
The ma
ain connection at thee machine must be
e freely accessible.
MAINTE
ENANCE INSTRUC
CTIONS
To ensu
ure proper operatioon and function, perriodic oiling of the ccutting system is
required
d. Failure to oil youur cutting system co
ould result in reducced sheet capacity
perform
mance, excess noisee, paper jams and possible machine ffailure.
Run the
e machine in reversse after every 15-30
0 minutes of continuous use while
applying
g a thin strip of oil tto the cutting head.
-Squeez
ze the lubricant acrross the full width o
of the cutters.
-Clean the
t shredder housinng using a soft clotth dampened with a mild solution of
deterge
ent (such as dish waashing liquid) and w
warm water. DO NO
OT use chemical
cleaners
s or solvents.
CLEAN
NING PHOTO EYE SENSORS
1.
2.
3.
4.
5.
ety
Unplug your macchine – for your safe
nue
Lift CD Flap on m
machine (If no flap installed, disregard this line and contin
on) Note: In the ccenter of the paperr slot, you should se
ee (2) transparent
squares - one on either side of the sslot.
nd
el and wipe back an
Use compressed air or take a dry tisssue or paper towe
forth a few times just to dust that are
ea off
Replace flap if neecessary
Plug machine bacck in
OPERATING INSTRUCTION
NS
3.
To shred a CD, D
DVD or credit card iinsert through desig
gnated slot Ⓔ.
4.
After shredding, ppress the stand-by button Ⓑ to turn offf the shredder and
turn off the powerr switch in back of sshredder Ⓐ.
5.
Empty the waste bin regularly to pre
event jams and dam
mage to cutting
mechanism.
6.
When the shreddder is overheated, th
he FWD/Overheat Ⓒ button will blin
nk.
7.
When the shreddder is overloaded, th
he REV/Overload Ⓓ button will blink
k.
8.
Standby buttonⒷ will turn off whenn bin is opened. A
After the bin is return
ned
to the correct possition, the machine will resume operattion.
AUTO CLEAN
C
FUNCTION
N
If maxim
mum sheet capacityy has been exceeded, the shredder w
will start auto reverse
for 1 to 3 seconds for the uuser to take paperss out. After that the
e machine will auto
forward 1 to 3 seconds to cclean the remaining
g paper. Reduce the number of shee
ets
and con
ntinue shredding.
SHREDDER CONTROLS
Buttons
STAND
DBY MODE
Switch Main Powe
er Switch Ⓐ to ON position.
Press Power Butto
on Ⓑ to turn on.
The shrredder is equipped with an energy savving standby mode which will activate
after 30 minutes of being iddle. To resume, prress the stand-by b
button Ⓑ.
Press Power Butto
on Ⓑ to turn the po
ower off.
Press and hold FW
WD to manually ope
erate shredder in fo
orward Ⓒ.
Press and hold RE
EV to manually operate shredder in rev
verse Ⓓ.
TROUB
BLESHOOTING
SHRED
DDER WILL NOT O
OPERATE
OPERATION
1.
1. Make sure shreddder is plugged into power source and the main power
switch Ⓐ is switcched on.
T
Turn on the main po
ower switch in back
k of shredder Ⓐ. Press
P
the stand-by
2. Make sure the waaste bin is fully inse
erted into the shred
dder housing.
b
button Ⓑ. The follo
owing function butto
ons will illuminate: stand-by
s
button Ⓑ,,
tthe FWD Ⓒ and RE
EV Ⓓ.
2.
Insert paper into pa
aper feed slot Ⓔ. Do
D not fee more tha
an 12 sheets at one
e
ttime. The shredderr will stop after pap
per has passed thro
ough.
PAPER
R JAM
1.
2.
Press and hold R
REV Ⓓ button to cle
ear the jam.
Press power buttoon to continue shre
edding.
ead
CAUTION: Sharpp cutter blades. Do not reach underneath the shredder he
3.
to remove jammed paper. Serious injury can result.
If the paper jam cannot be cleared by pressing the REV button:
a. Tear or cut the remaining paper just above the shredder throat.
b.
Press power button Ⓑ to switch off the machine.
c.
Press power button Ⓑ again to switch on the machine in order to
d.
clean the jammed paper inside the throat.
Repeat steps (b) and (c) until all paper is cleared from inside the
throat.
SHREDDER STOPS WHILE SHREDDING
1.
Switch off the main power switch Ⓐ and unplug the shredder from the power
source.
2.
Plug the shredder into power source. Switch on the main power switch Ⓐ in
back of shredder and press the stand-by button Ⓑ.
3.
For further troubleshooting, please contact product support 800-613-2110.
STANDARD PRODUCT WARRANTY
Quality is part of the company philosophy and all products are manufactured to the
highest quality standards. All technical data and measurements are approximate
values and based upon single shift operations. All products are subject to different
limits and specifications due to operation length, paper size, grain, weight,
misuse/abuse and power configurations.
Prior to operation read the Manufacturers Operating Instructions included with this
product. This will help ensure all precautions are taken to avoid cancellation of the
manufacturer’s warranty.
The manufacturer warrants that any new products sold will be free from defects
in material and workmanship when used under specified and normal operating
conditions. This warranty is void if repairs are necessitated by accident,
misuse, abuse, water damage or fire.
The capabilities of all products are in each specification flier. Exceeding model
specifications causing product failure is not covered by this warranty. Modifications,
alterations and repairs must be performed by an authorized technician. Lubrication
for cross cut shredders is required every fifteen to thirty minutes of operation, to
maintain top working condition and this warranty.
Compact Shredders & Shredstar Models
Failure caused by defect is limited to two (2) years from date of invoice. A maximum
of one replacement unit is authorized during the warranty period. Strip and cross cut
cutting rollers are warranted to be free of manufacturer defects for the life of the
shredder from date of invoice.
Notes:



Freight or transportation damage is not classified as a warranty repair in any
case.
Proof of purchase invoice is required from the end-user warranty validation
or warranty registration date.
All parts under warranty will be shipped and invoiced using standard costs
and will be credited for the full amount only when the defective part is
returned.