Download Albion AG40R User guide
Transcript
OPERATING MANUAL AND USER GUIDE !"#$%&!'!"#(%& www.albionamps.com AG40_AG80.indd 1 2011-5-5 18:35:05 OPERATING MANUAL AND USER GUIDE & AG40_AG80.indd 2 2011-5-5 18:35:05 Contents Important Safety Instructions ...................................................................................... 1 Important Warnings ....................................................................................................... 2 Designer's Introduction................................................................................................. 3 2XWOLQH6SHFL¿FDWLRQ ..................................................................................................... 3 AG40R Features and Controls ...................................................................................... 4 5HDU3DQHODQG6SHFL¿FDWLRQ....................................................................................... 5 AG80R Features and Controls ...................................................................................... 6 5HDU3DQHODQG6SHFL¿FDWLRQ....................................................................................... 7 AG40_AG80.indd 3 2011-5-5 18:35:05 OPERATING MANUAL AND USER GUIDE Important Safety Instructions 1. Read these instructions – All the safety and operating instructions should be read before this product is operated. 2. Keep these instructions – The safety and operating 13. Unplug the apparatus during lightning storms or when instructions should be retained for future reference. unused for long periods of time. 3. Heed all warnings – All warnings on the appliance 5HIHUDOOVHUYLFLQJWRTXDOL¿HGSHUVRQQHO6HUYLFLQJLV and in the operating instructions should be adhered required when the apparatus has been damaged in to. any way including: power supply cord or plug damage, 4. 5. Follow all instructions – All operating and use liquid spillages, objects falling into the unit, exposure instructions should be followed. to rain/moisture or impact damage. 15. Please keep the unit in a well ventilated environment. Do not use this apparatus near water – The appliance should not be used near water or moisture – for 16. CAUTION: These servicing instructions are for use example, in a wet basement or near a swimming pool by qualified service personnel only. To reduce the etc. risk of electric shock, do not perform any servicing 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in other than that contained in the operating instructions XQOHVV\RXDUHTXDOL¿HGWRGRVR :$51,1*7RUHGXFHWKHULVNRI¿UHRUHOHFWULFVKRFN accordance with the instructions. do not expose this apparatus to rain, moisture and 8. 9. Do not install near any heat sourc es such as dripping or splashing of liquids. Containers filled radiators, heat registers, stoves, or other apparatus with liquids such as vases or drinks should never be LQFOXGLQJDPSOL¿HUVWKDWSURGXFHKHDW placed on top of or near the unit. Do not defeat the safety purpose of the polarized or 18. WARNING: The mains plug/appliance coupler is used grounding plug. A polarized plug has two blades with as disconnect device, the disconnect device shall one wider than the other. A grounding plug has two remain readily operable. blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the SURYLGHGSOXJGRHVQRW¿WLQWR\RXURXWOHWFRQVXOWDQ electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched par ticularly at the plugs, convenience 7KHOLJKWQLQJÀDVKZLWKDUURZKHDGV\PEROLVWRDOHUW receptacles, and at the point where they exit from the the user to the presence of non-insulated "dangerous apparatus. voltage" within the product's enclosure that may be RIVXI¿FLHQWPDJQLWXGHWRFRQVWLWXWHDULVNRIHOHFWULF 11. Only use attachments/accessories specified by the shock. manufacturer. 12. Use only with the cart, stand, tripod, bracket or - Warning: To reduce the risk of electric shock, do WDEOHVSHFL¿HGE\WKHPDQXIDFWXUHURUVROGZLWKWKH QRW UHPRYH FRYHU RU EDFN DV WKHUH DUH QR XVHU apparatus. When a cart or rack is used, use caution VHUYLFHDEOHSDUWVLQVLGH5HIHUVHUYLFLQJWRTXDOL¿HG when moving the cart/ apparatus combination to personnel. avoid injury from tip-over. & AG40_AG80.indd 4 1 2011-5-5 18:35:05 series - The exclamation point within an equilateral triangle PRLVWXUHHQYLURQPHQWVXFKDVUDLQRUDOORZLWWRJHW is intended to aler t the user to the presence of wet. important operating and maintenance instructions in the literature accompanying the appliance. $/:$<6 XVH FRUUHFW DQG ZHOO PDLQWDLQHG FDEOHV IRU all inter-connections whether for power, speaker or 20. signal connections. If in any doubt, get them checked Protective earthing terminal. The apparatus should be connected to a mains socket outlet with a or renew immediately. protective earthing connection. 1(9(5XVH\RXUDPSOL¿HUSURGXFWVZLWKDQ\FRROLQJ 21. vents covered, even partially. Your amp loves being Correct Disposal of this product. This marking indicates that this product should not be disposed fed nice cool air! with other household wastes throughout the EU. To prevent possible harm to the environment or human 3$57,&8/$5/< ZLWK YDOYH WXEH DPSV DOORZ \RXU health from uncontrolled waste disposal, recycle amp to warm up before playing, 5 minutes is a it responsibly to promote the sustainable reuse of good length of time. Also allow your amp to have a material resources. To return your used device, good cool down after playing and before moving it, please use the return and collection systems or especially into the back of a car on a cold winter’s contact the retailer where the product was purchased. night! Your valves will last longer if you give them a They can take this product for environmentally safe little respect and TLC. Valves are pretty tough when recycling. you think of what they are made from – but can be very fragile if treated with physical abuse. 22. WARNING: The terminals marked with the symbol of “ ” may be of sufficient magnitude to constitute a $/:$<6XVHDFDEOHUDWHGIRUORXGVSHDNHUFRQQHFWLRQ risk of electric shock. The external wiring connected XVHIRUFRQQHFWLQJ\RXUDPSOL¿HUWR\RXUORXGVSHDNHU to the terminals requires installation by an instructed system. DO NOT use a screened guitar cable for person or the use of ready-made leads or cords speaker use. according to manufacturer’s instruction. NEVER use your amplifier without it connected to a ³&ODVV :LULQJ³ IRU DOO RWKHU 7(50,1$/6 SURYLGHG suitable matched loudspeaker system. the audio output power exceeds 10W per channel under normal operating conditions or the apparatus is :$51,1* 6RPHWLPHV SDUWV RI WKH RXWVLGH RI \RXU LQWHQGHGWREHLQVWDOOHGRULQWHUFRQQHFWHGLQWKH¿HOG DPSOL¿HUPD\JHWKRWWRWKHWRXFK7KLVLVTXLWHQRUPDO E\D6.,//('3(5621 and will be within safe operational limits. These limits are set by various countries safety approvals committees, and we at Albion Musical Instruments Important Warnings design, build, test, and have approved our products to WKHVHLQWHUQDWLRQDOVWDQGDUGV,H&(8/&6$&% ETL etc. $/:$<6 UHDG WKH PDQXDO RI \RXU QHZ DPSOLILHU ± HYHQLI\RXDUHH[SHULHQFHGZLWKJXLWDUDPSOL¿HUVDQG EMC INTERFERENCE. Even though all Albion their technology! There could be something important Musical Instruments products are designed and that you need to know. tested to international electro-magnetic interference standards, please note that cellular phones in close $/:$<6FKHFNWKDW\RXUQHZDPSOL¿HULVVXLWHGWRWKH proximity may cause some interference with your mains power supply in your country. DPSOL¿HU 1(9(5 GLVFRQQHFW WKH HDUWK JURXQG FRQQHFWLRQ $/:$<6KDYH\RXUDPSOL¿HUVHUYLFHGE\DWHFKQLFLDQ from your amplifier. It is there to prevent you from qualified in servicing musical instrument amplifier receiving a fatal electric shock! products. If in doubt please contact your dealer. NEVER use your amplifier equipment in a high 2 AG40_AG80.indd 5 & 2011-5-5 18:35:06 OPERATING MANUAL AND USER GUIDE FKDQQHO 92/80( DQG RYHUGULYH FKDQQHO *$,1 DQG Designer's Introduction 92/80( FRQWUROV 7KH '5,9( VZLWFK IRRWVZLWFKDEOH allows you to set up the preamp circuit for clean and We l c o m e t o A l b i o n M u s i c a l I n s t r u m e nt s AG 4 0 R RYHUGULYHIXQFWLRQV%$660,''/(DQG75(%/(FRQWUROV and AG 8 0 R c ombo amps. Having designed many IRUWRQHVKDSLQJDSSOLFDWLRQVDQGD5(9(5%FRQWUROIRU competitively priced amps, many of them of them have WKHLQEXLOWGLJLWDOUHYHUEFLUFXLWDOVRIRRWVZLWFKDEOH been destined to be award winning and certainly “classics” in their own right, I realised that I had somewhat of a 7KHDPSLVDOVR¿WWHGZLWKDPP,QSXW-DFNWREHDEOH challenge in front of me when creating the AG range. “How to connect your MP3 or CD player (or any other auxiliary do I beat what I have done before?”, “How can I raise GHYLFHVXFKDVDGUXPPDFKLQH7KLVLVDVWHUHRVRFNHW WKHSUR¿OHRIORZHUFRVWSUDFWLVHDQG³ZHHNHQG´DPSVWR and uses a standard stereo 3.5mm lead, mixing the signal make them into really serious amps?”, I realised there was into mono mode suitable for the amplifier circuit, giving quite a massive challenge in front of me! I think that what I you the facility to play along to recorded tracks for practise have done with the AG range actually surpasses even my purpose. expectations. I hope that you agree with me. Another 3.5mm socket allows the use of standard stereo headphones for private use. Thank you The output of the AG40R can also be plugged into another loudspeaker cabinet, bypassing the internal loudspeaker. Plugging into a bigger cabinet widens the tone available to something rather special! 2XWOLQH6SHFLÀFDWLRQ The AG80R has a full two channel control line-up of consisting of NORMAL channel and OVERDRIVE channel giving you a very wide range of tones from Clean to The AG40R and the AG80R combo amps features a Crunch to very serious Overdrive. YHU\XQLTXH³K\EULG´SUHDPSOL¿HUVHFWLRQFRPELQLQJKLJK YROWDJH)(7V¿HOGHIIHFWWUDQVLVWRUVDQGD$;(&& Each channel has a full complement of GAIN, VOLUME, YDOYHRUWXEHDVLVNQRZQLQWKH86$7KLVVSHFLDOFLUFXLW 75(%/(0,''/(DQG%$66FRQWUROV7KHWZRFKDQQHOV is supplied with a high voltage dc supply, again pretty are footswitchable for full access to these sounds. This unique in small guitar amplifiers. This combination of is complemented by the in-built digital reverb circuit (also circuit gives great valve tone, as it should because it is IRRWVZLWFKDEOH pretty much a valve circuit. The special high voltage FET that we use is the closest electronic device to an actual 7KHDPSLVDOVR¿WWHGZLWKDPP,QSXW-DFNWREHDEOH valve, but without some of the drawbacks of using an to connect your MP3 or CD player (or any other auxiliary DFWXDO YDOYH FRVW KHDW KLJK SDUWV FRXQW DQG ZLOO JLYH GHYLFHVXFKDVDGUXPPDFKLQH7KLVLVDVWHUHRVRFNHW reliable performance without worry to you, but giving very and uses a standard stereo 3.5mm lead, mixing the signal much a valve like tone in its performance. into mono mode suitable for the amplifier circuit, giving you the facility to play along to recorded tracks for practise 7KHSRZHUDPSOL¿HUFLUFXLWVRIWKH$*5DQGXVHD purpose. solid state power amp circuit that also has some “tweaks” that lead to a very convincing valve-like tone. Another 3.5mm socket allows the use of standard stereo Headphones for private use. The AG40R uses a 10 inch loudspeaker professionally designed to provide a very full and satisfying tone in a The speaker MUTE switch allows the headphone output nicely proportioned compact cabinet. Whilst the AG80R socket to double as a speaker emulated DI output with or is provided with a seriously beefy and tuneful 12 inch without the full loudspeaker sound. speaker, again the cabinet design leads to an easily transportable package that doesn’t look, or sound, out of place at home, in the studio, or on the stage. The AG40R has a two channel control line-up of (normal & AG40_AG80.indd 6 3 2011-5-5 18:35:07 series AG40R Features and Controls INPUT –0RQRó´-DFNVRFNHWIRULQVWUXPHQWLQSXW8VH GAIN and VOLUME controls become effective. The 2- a properly screened “guitar” cable for interconnection. ZD\IRRWVZLWFK$0,)6FDQEHFRQQHFWHGWRUHPRWHO\ There are many different makes of guitar cable available, change channels and mute the amp’s reverb section. ranging from fairly inexpensive to ver y expensive. 3OHDVHUHPHPEHUWKDWWRXVHWKHIRRWVZLWFKWKHQWKH$% Each have different characteristics, and depending on 'ULYHVZLWFK0867EHSXVKHGLQ your particular guitar will give different results, all very confusing for the inexperienced! For instance, a “cheap” GAIN (overdrive) – this control determines the amount cable with high capacitance (which would normally be of signal that the preamp circuit has to produce the WHUPHG DV D ³QRW YHU\ JRRG FDEOH´ FDQ DFWXDOO\ EH RI overdrive sound. Low settings will produce an almost benefit for an overly bright single coil guitar by taming clean slightly crunchy tone, whilst higher to maximum the very high end frequencies. Alternatively, a very low settings will produce intense overdriven distortion tones. capacitance cable can help brighten up a muddy sounding hum-bucker type guitar. If possible experiment to try and VOLUME (overdrive – this quite simply controls the find what suits you and your guitar best. Hopefully your output of the sound generated by the overdrive preamp, GHDOHUFDQKHOS\RXFKRRVHWKHULJKWFDEOH,IXVLQJDQ); giving you the required sound level and balance that you pedal system then the best advice is to use high quality, require. low noise, low capacitance cable from pedals to amp TREBLE, MIDDLE, BASS EQ – The EQ circuit connection. works on both the Normal and Overdrive channels. The NORMAL VOLUME – This controls the level of the AG40 EQ system is of the time-honoured passive guitar Normal channel. At lower settings the sound will be clean amp system as used by virtually all guitar amps even and will have a bit of treble lift that will compensate the the very greatest pro amps, but with an added bass sound to enable your ear to hear a good spectrum of boost circuit that gives the AG range of amps an added tone without it sounding flat. At higher control settings warmth especially at low volumes. This type of tone the sound will thicken up and get louder. As it reaches shaping is very wide ranging and very versatile, although maximum volume the sound will “crunch” up as the please remember it is also very interactive so that each DPSOL¿HUFLUFXLWZLOOVWDUWWREHRYHUGULYHQ$ZRUGRIQRWH control also has an influence on the other controls. Different types of guitars and pick-ups have very different Experimentation is the key – please start with these tonal characters and the voltage level from the pick- controls set to mid position. ups can vary by quite a large amount, thus the control positioning will vary depending on your guitar and what REVERB – This controls the amount of reverb signal VRXQG \RX ZDQW $V D UXOH RI WKXPE 6LQJOHFRLO W\SH from the on-board digital reverb circuit that is mixed with guitars have less output and a brighter sound. Guitars the direct preamp signal. This is footswitchable on or off with Hum-buckers will have a thicker louder sound. Also when using the above mentioned footswitch. SLFNXSKHLJKWKDVDJUHDWLQÀXHQFHRQWRQHDQGYROXPH Further away from the strings will be cleaner and quieter, SWITCH – FRQQHFW WKH DERYH PHQWLRQHG $0, )6 closer to the strings will be fatter and louder. footswitch into this socket. DRIVE SWITCH & LED INDICATOR – the DRIVE AUX IN – This socket accepts the stereo output of a pushswitch changes the amplifier channel from Normal MP3/CD player, or any other auxiliary input device such $WR2YHUGULYH%:KHQ2YHUGULYHLVVHOHFWHGWKH/(' as a rhythm drum machine. Please use a standard 3.5mm next to the switch is illuminated and the Overdrive channel 6WHUHRVFUHHQHGLQWHUFRQQHFWFDEOH 4 AG40_AG80.indd 7 & 2011-5-5 18:35:07 OPERATING MANUAL AND USER GUIDE HP OUT – This 3.5mm socket is the output to feed into 6SHFL¿FDWLRQ headphones for silent practise. Any standard 16 ohm stereo headphones can be used, although as with all ZDWWV506RXWSXWLQWRLQWHUQDOLQFKRKPLPSHGDQFH things, the better the headphone the better the sound. loudspeaker. DO NOT USE ANY OTHER LOAD :$51,1*'212786($1<27+(563($.(5/2$' Rear Panel IMPEDANCE! IMPEDANCE. LOUDSPEAKER OUTPUT – the output jack socket RII$;(&&GRXEOHWULRGHVPDOOVLJQDOYDOYHWXEH mounted on the rear panel of the AG40 allows the amplifier to be connected into an external loudspeaker 0DLQV)XVH 9+]VXSSO\ 7$WLPHODJ unit. When doing this the internal 10 inch loudspeaker 250V rated 20mm glass fuse is disconnected. The amplifier will feed into a load of 0DLQV)XVH 9+]VXSSO\ 7$WLPHODJ9 between 8 ohms and 16 ohms only. rated 20mm glass fuse 0DLQV )XVH 9 +] VXSSO\ 7P$ WLPH ODJ DO N USE O T ANY U S EOTHER A N YLOAD O T HIMPEDANCE! ER LOAD DO NOT IMPEDANCE! 250V rated 20mm glass fuse 0DLQV)XVH 9+]VXSSO\ 7P$WLPHODJ 250V rated 20mm glass fuse Great sounds can be achieved using other guitar speaker cabinets, especially running into a 4x12” cabinet. Using 6L]HV±:*5[´FRPER'LPHQVLRQVPP : a good speaker system brings out the very impressive [+['±:HLJKW .J sound capabilities of the AG40, making it into an even more impressive amp. CAUTION! CAUTION! There are no user serviceable parts mounted There are no user serviceable parts mounted inside your amplifier! Refer servicing to suitably qualified LQVLGH\RXUDPSOL¿HU5HIHUVHUYLFLQJWRVXLWDEO\ personnel. TXDOL¿HGSHUVRQQHO MAINS INPUT – the mains input receptacle allows for the connection of the mains power cord, and also houses WKHPDLQVSRZHUIXVH7RFRPSO\ZLWK,QWHUQDWLRQDO6DIHW\ 5HJXODWLRQVIRU\RXUVDIHW\DQGSURWHFWLRQ\RXUDPSOL¿HU This means that for your own safety and the correct performance of your amplifier, do not open the chassis unless you really do know what you are doing! is supplied to work with the mains supply in your country. Please check the white rating label fitted to the back panel. If in any doubt, please check with your supplier. It is of utmost importance to use the correct earthed and rated SRZHUFRUGDVLVVXSSOLHGZLWK\RXUDPSOL¿HU WARNING! DO NOT USE WITHOUT :$51,1*'212786(:,7+287&211(&7,1*7+( CONNECTING THE EARTH (GROUND) WIRE. ($57+*5281':,5( In the case of the mains fuse blowing, this can be changed E\UHPRYLQJWKHSRZHUFRUGFRQQHFWRUIURPWKHDPSOL¿HU receptacle and with the aid of a small screwdriver the small drawer in the receptacle can be withdrawn allowing access to the mains power Fuse. WARNING! USE WARNIN G ! THE U SCORRECT E T H E REPLACEMENT CORRECT VALUE ONLY! REPLACEMENT VALUE ONLY! A WORD OF ADVICE about fuses – if a fuse blows it is usually for a very good reason, it could be anything from a voltage spike on the mains power, to a serious malfunction of your amplifier. Fuses are there for your protection – treat them with respect, and never replace with the wrong value! & AG40_AG80.indd 8 5 2011-5-5 18:35:07 series AG80R Features and Controls INPUT –0RQRó´-DFNVRFNHWIRULQVWUXPHQWLQSXW8VH start the circuit is designed for much more distortion a properly screened “guitar” cable for interconnection. and overdrive, and also is voiced to focus in on the best There are many different makes of guitar cable available, frequencies that overdrive works at. Alternatively to the ranging from fairly inexpensive to very expensive. Each Normal channel, the EQ on the Overdrive channel is placed have different characteristics, and depending on your after the gain and distortion circuitry – thus the EQ tailors particular guitar will give different results, all very confusing the tone of the distortion. for the inexperienced! For instance, a “cheap” cable with high capacitance (which would normally be termed as a GAIN – this control determines the amount of signal that ³QRW YHU\ JRRG FDEOH´ FDQ DFWXDOO\ EH RI EHQHILW IRU DQ the preamp circuit has to produce the overdrive sound. Low overly bright single coil guitar by taming the very high end settings will produce an almost clean tones; whilst higher frequencies. Alternatively, a very low capacitance cable can to maximum settings will produce overdriven tones. The help brighten up a muddy sounding hum-bucker type guitar. intensity and voice of these will change from normal to If possible experiment to try and find what suits you and overdrive channels. your guitar best. Hopefully your dealer can help you choose WKHULJKWFDEOH,IXVLQJDQ);SHGDOV\VWHPWKHQWKHEHVW VOLUME – this quite simply controls the output of the advice is to use high quality, low noise, low capacitance sound generated by the preamp, giving you the required cable from pedals to amp connection. sound level and balance that you require. A- B SWITCH & LED INDICATORS – WKH $ % TREBLE, MIDDLE, BASS EQ – The EQ circuit works pushswitch changes the amplifier channel from Normal independently on both the Normal and Overdrive channels. $WR2YHUGULYH%:KHQ1250$/LVVHOHFWHGWKH/(' The AG80 EQ system is of the time-honoured passive next to the switch is illuminated and the Normal channel guitar amp system as used by virtually all guitar amps even controls become effective. And of course, when Overdrive the very greatest pro amps, but with an added bass boost is selected the LED next to the switch is illuminated and the circuit that gives the AG range of amps an added warmth Overdrive channel controls become effective. The 2- way especially at low volumes. This type of tone shaping is very IRRWVZLWFK$0,)6FDQEHFRQQHFWHGWRUHPRWHO\FKDQJH wide ranging and very versatile, although please remember channels and mute the amp’s reverb section. Please it is also very interactive so that each control also has an UHPHPEHU WKDW WR XVH WKH IRRWVZLWFK WKHQ WKH $% 'ULYH LQÀXHQFHRQWKHRWKHUFRQWUROV([SHULPHQWDWLRQLVWKHNH\ VZLWFK0867EHSXVKHGLQ – please start with these controls set to mid position. The differences between the Normal and Overdrive REVERB – This controls the amount of reverb signal from channels is worth understanding. The Normal channel the on-board digital reverb circuit that is mixed with the is designed to give predominantly great clean to slightly direct preamp signal. This is footswitchable on or off when overdriven crunch sounds. To achieve this the EQ circuit is using the above mentioned footswitch. placed before the channels gain circuits, thus the EQ sort of works like 3 frequency dependant gain controls. When AUX IN – This socket accepts the stereo output of a the Normal gain control is set close to, or at, maximum then MP3/CD player, or any other auxiliary input device such the post EQ gain circuits get overdriven and can be fine as a rhythm drum machine. Please use a standard 3.5mm tuned with the EQ – try turning up the MIDDLE control for a 6WHUHRVFUHHQHGLQWHUFRQQHFWFDEOH very “singing” tone. HP OUT – This 3.5mm socket is the output to feed into headphones for silent practise. Any standard 16 ohm The Overdrive channel works slightly differently. For a 6 AG40_AG80.indd 9 & 2011-5-5 18:35:07 OPERATING MANUAL AND USER GUIDE stereo headphones can be used, although as with all WARNING! W A R N I USE N G !THE U SCORRECT E T H E REPLACEMENT CORRECT REPLACEMENT VALUE ONLY! things, the better the headphone the better the sound. On the AG80 the headphone output is fed from an intricate DFWLYHVSHDNHUHPXODWLQJ¿OWHUQHWZRUNWRSURGXFHDPRUH A WORD OF ADVICE about fuses – if a fuse blows it is accurate “guitar speaker” sound through headphones. This usually for a very good reason, it could be anything from a circuit is placed before the power amplifier section, and voltage spike on the mains power, to a serious malfunction WKHUHIRUHFDQ$/62EHXVHGDVDQHPXODWHG',/LQH2XW RI\RXUDPSOL¿HU)XVHVDUHWKHUHIRU\RXUSURWHFWLRQ±WUHDW for connecting into a PA or Recording system. them with respect, and never replace with the wrong value! POWER AMP STANDBY/ACTIVE SWITCH – This 6SHFL¿FDWLRQ switch mutes the input of the AG80 power amplifier. This KDVWZRSXUSRVHV$LWFDQEHXVHGDVD6WDQGE\VZLWFK ZDWWV506RXWSXWLQWRLQWHUQDOLQFKRKPLPSHGDQFH WRPXWH\RXUVWDJHVLJQDOZLWKRXWWXUQLQJRIIWKHDPSOL¿HU loudspeaker. GXULQJEUHDNVDWJLJVHWF±%ZKHQXVLQJWKH+HDGSKRQH out socket for headphone only, or for silent DI output, WA R N I N G ! D O N O T U S E A N Y O T H E R :$51,1*'212786($1<27+(563($.(5/2$' VZLWFKLQJWR6WDQGE\JLYHV\RXVLOHQWSHUIRUPDQFH SPEAKER LOAD IMPEDANCE. IMPEDANCE. Rear Panel RII$;(&&GRXEOHWULRGHVPDOOVLJQDOYDOYHWXEH FX LOOP SEND & RETURN – $ QRPLQDOO\ G% 0DLQV)XVH 9+]VXSSO\ 7$WLPHODJ VHULHV HIIHFWV ORRS 6HQG FRQQHFWV WR WKH LQSXW RI \RXU 250V rated 20mm glass fuse effects system. Return connects to the output of your 0DLQV)XVH 9+]VXSSO\ 7$WLPHODJ9 effects system. Generally it is quite unwise to use “stomp rated 20mm glass fuse box” type pedals in an effect loop, they are not designed 0DLQV)XVH 9+]VXSSO\ 7$WLPHODJ9 for such use, and are best suited to be connected between rated 20mm glass fuse JXLWDUDQGWKHDPSOL¿HULQSXW);ORRSVDUHEHVWVXLWHGIRU 0DLQV )XVH 9 +] VXSSO\ 7$ WLPH ODJ delay, modulation and EQ processors. Use good quality 250V rated 20mm glass fuse screened cables! 6L]HV±$*[´FRPER'LPHQVLRQVPP :[ SWITCH ± FRQQHFW WKH DERYH PHQWLRQHG $0, )6 +['±:HLJKW .J footswitch into this socket. CAUTION! MAINS INPUT – the mains input receptacle allows for CAUTION! There are no user serviceable parts mounted There are no user serviceable parts mounted inside your amplifier! Refer servicing to suitably qualified LQVLGH\RXUDPSOL¿HU5HIHUVHUYLFLQJWRVXLWDEO\ personnel. TXDOL¿HGSHUVRQQHO the connection of the mains power cord, and also houses WKHPDLQVSRZHUIXVH7RFRPSO\ZLWK,QWHUQDWLRQDO6DIHW\ 5HJXODWLRQVIRU\RXUVDIHW\DQGSURWHFWLRQ\RXUDPSOL¿HU is supplied to work with the mains supply in your country. This means that for your own safety and the correct performance of your amplifier, do not open the chassis unless you really do know what you are doing! 3OHDVHFKHFNWKHZKLWHUDWLQJODEHO¿WWHGWRWKHEDFNSDQHO If in any doubt, please check with your supplier. It is of utmost importance to use the correct earthed and rated SRZHUFRUGDVLVVXSSOLHGZLWK\RXUDPSOL¿HU AMI FS2 FOOT-PEDAL – the 2 way foot-pedal supplied DO O N O TT UUSSEE WWI TI THH OO UU TT WW AARRNNI INNGG!! D CONNECTING THE EARTH (GROUND) WIRE. CONNECTING THE EARTH (GROUND) WIRE. ZLWK\RXU$*RU$*DPSOL¿HUKDVDFRXSOHRIIHDWXUHV that you may want to be made aware of. Firstly the supplied stereo jack cable can be replaced if required by any In the case of the mains fuse blowing, this can be changed ó´ 6WHUHR -DFN OHDG ± HLWKHU VFUHHQHG RU XQVFUHHQHG by removing the power cord connector from the amplifier 6HFRQGO\ WR KHOS WKH IRRWSHGDO ILW EHWWHU LQ ZLWK \RXU receptacle and with the aid of a small screwdriver the small normal stage set-up, the cable connection can be made drawer in the receptacle can be withdrawn allowing access 5LJKW+DQGDVVXSSOLHGRUFDQEHFRQYHUWHGWR/HIW+DQG to the mains power Fuse. connection. Please see the diagram below. & AG40_AG80.indd 10 7 2011-5-5 18:35:08 series 8 AG40_AG80.indd 11 & 2011-5-5 18:35:08 OPERATING MANUAL AND USER GUIDE & AG40_AG80.indd 12 ,$*+RXVH6RYHUHLJQ&RXUW(UPLQH%XVLQHVV3DUN+XQWLQJGRQ&DPEV3(;8(QJODQG www.albionamps.com The information in this brochure is subject to change without notice. All rights reserved © 2010 Albion. Albion is a member of the IAG Group. 2011-5-5 18:35:09