Download Mitsubishi CS-40309 User`s manual
Transcript
User’s Manual MULTI-LOOP MODULE TYPE TEMPERATURE CONTROLLER <Enhanced Communication Module (Mitsubishi’s PLC programless communication)> TYPE: PUMCM PWR PUM-C BUS LOADER RX1 TX1 STATION 45 E F0 1 23 89 67 CD TX2 AB RX2 INP-TN5A0202c-E 2 INP-TN5A0202-E Please Read First (Safety Warnings) Please read this section thoroughly before using and observe the mentioned safety warnings fully. • In cases where damage or problems with this equipment may lead to serious accidents, install appropriate external protective circuits. • To prevent damage and failure of the equipment, provide Safety warnings are categorized as "Warning", "Caution" or "Risk of Electrical Shock". the rated power voltage. • To prevent electric shock and equipment failure, do not turn the power ON until all wiring is complete. Warning Improper use of the equipment may result in death or serious injuries. • Before turning the power ON, confirm that clearance Caution Improper use of the equipment may cause injury or property damage. • Do not touch the terminal while the machine is ON. Doing Risk of Electrical Shock Indicates that a risk of electrical shock is present and the associated warning should be observed. • Never disassemble, convert, modify or repair this space has been secured to prevent shock or fire. so risks shock or equipment errors. equipment.Doing so risks abnormal operation, shock or fire. • All of the wiring should be class 1 type wiring or the low Warning voltage wires are routed separately from the hazardous voltage wires to ensure separation of circuits. Installation and Wiring ● This equipment is intended to be used under the following conditions. Ambient temperature -10 to 50 degree C Ambient humidity 90% RH or below (with no condensation) Vibration 10 to 70Hz less than 9.8m/s² (1G) Warm-up time 30 min. or more Installation category IEC1010-1: class II Pollution level IEC1010-1: degree 2 • When using a AWG-16 cable, you should use the crimp terminal that material thickness is 0.9mm or less. Maintenance • When installing or removing the equipment, turn the power OFF. Otherwise, shock, operational errors or failures may be caused. • Periodic maintenance is recommended for continuous and ● Between the temperature sensor and the location where the voltage reaches or generates the values described below, secure clearance space and creepage distance as shown in the table below. If such space cannot be secured, the EN61010 safety safe use of this equipment. • Some parts installed on this equipment have a limited life and/or may deteriorate with age. • The warranty period for this unit (including accessories) is one year, if the product is used properly. compliance may become invalid. Voltage used or generated by any assemblies Clearance Space [mm] Creepage Space [mm] Caution Up to 50 Vrms or Vdc 0.2 1.2 Up to 100 Vrms or Vdc 0.2 1.4 Up to 150 Vrms or Vdc 0.5 1.6 For install in UL listed enclosure only. Up to 300 Vrms or Vdc 1.5 3.0 Please avoid installing in the following locations. Above 300 Vrms or Vdc Please consult our distributor ● For the above, if voltage exceeds 50Vdc (called danger voltage), functional insulation is required between the earth and all terminals of the equipment. Note that the insulation class for this equipment is as follows. Before installing, please confirm that the insulation class for equipment meets usage requirements. Cautions when Installing • Locations in which the ambient temperature falls outside the range of 0 to 50 degrees C when equipment is in use. • Locations in which the ambient humidity falls outside the range of 45 to 85% RH when equipment is in use. • Locations with rapid temperature changes, leading to dew condensation. • Locations with corrosive gases (especially sulfide gas, ammonia, etc.) or flammable gases. Power supply Loader communication Functional insulation (AC1000V) INP-TN5A0202-E RS-232C communication RS-422 communication RS-485 communication • Locations with vibration or shock directly. Functional insulation (AC500V) 3 • Locations in contact with water, oil, chemicals, steam or hot water. (If the equipment gets wet, there is a risk of electric shock or fire, so have it inspected by Fuji distributor.) Error Operation • The alarm function does not work properly when an error occurs unless the settings are made correctly. Always verify its setting before operation. • Locations with high concentrations of atmospheric dust, salt or iron particles. • Locations with large inductive interference, resulting in static electricity, magnetic fields or noise. Others • Please do not wipe the equipment with organic solvents • Locations in direct sunlight. such as alcohol or benzene, etc. If wiping is necessary, • Locations that build up heat from radiant heat sources, use a neutral cleaning agent. • Do not use mobile phones near this equipment (within etc. • A switch or circuit breaker shall be included in the building installation. Please be it in close proximately to the equipment and within easy reach of the operator, and mark it as the disconnecting device for the equipment. 50cm). Otherwise a malfunction may result. • Malfunctions may occur if the equipment is used near a radio, TV, or wireless device. • This equipment requires approx. 5 to 30 seconds before it starts to output. Cautions when Mounting to Cabinets/DIN Rails • Before installing and wiring, take necessary measures for electrostatic discharge (ESD). • In case of mounting the temperature controllers to DIN • The power supply for this product is 24V DC. Please use rails, remember to push up the locking tabs to fasten the the power source of appropriate volume depending on the controllers onto DIN rail. number of units you connect. • To connect controllers, first release all locking tabs. Then, connect controllers and push up all locking tabs. Make sure that all locking tabs are fastened. • Never fail to turn the power OFF, before detaching the Recommended power supply: Cosel Electronics Co., Ltd. PBA Series Omron Corporation S8VM Series terminal block or removing the main unit from the base part. • In order to aid heat dissipation, do not block the top and the bottom of the equipment. • When mounting/dismounting controllers to /from DIN rails, 30mm of clearance above and under the controllers should be provided. Cautions for Wiring • For wiring to the terminal block, apply crimp type terminals size M3. Use terminal screws in this product only. Screw size: M3×7 (with square washer) Screw tightening torque: 0.78 N • m (8kgf • cm) • To avoid the influence of inductive noise, input signal wires should be separated from electric power lines or load lines. • To use the RS-232C communication, attach noise filters to the AC power lines. (Not necessary, provided that the noise suppression of the power line is thoroughgoing) • To comply with CE marking (EMC), we recommend to attach ferrite core to communication cable and power cable. 4 INP-TN5A0202-E Contents Please Read First (Safety Warnings) ………………… 3 3.4 Attaching accessories (optional) ………………… 3-13 Warning ……………………………………………… 3 Attaching side connecting terminal covers ………… 3-13 Installation and Wiring …………………………………… 3 Attaching endplates …………………………………… 3-13 Maintenance ……………………………………………… 3 3.5 Mounting with screws ……………………………… 3-14 Caution ……………………………………………… 3 3.6 Connection …………………………………………… 3-15 Cautions when Installing ………………………………… 3 Connection with PLC ………………………………… 3-15 Cautions when Mounting to Cabinets/DIN Rails ……… 4 Connecting modules ………………………………… 3-22 Cautions for Wiring ……………………………………… 4 Wiring for power supply ……………………………… 3-23 Error Operation …………………………………………… 4 Others……………………………………………………… 4 4 Programless Communication Operation ……………………………… 4-1 1 Overview ……………………………… 1-1 4.1 Device Memory …………………………………………4-3 1.1 Overview ………………………………………………1-3 How to use the device memory …………………………4-4 1.2 Model Code ……………………………………………1-4 Operation for the programless communications ………4-9 Programless Communication Module …………………1-4 Accessories (Optional) …………………………………1-4 1.3 Part Names and Functions ……………………………1-5 External View ……………………………………………1-5 Front Terminal Block ……………………………………1-6 Main part (Back face) ……………………………………1-8 Base Part …………………………………………………1-9 2 System Configuration Example … 2-1 2.1 System Configuration Example ………………………2-3 1:1 Connection ……………………………………………2-3 1:N Connection ……………………………………………2-5 Programless communication operating suggestions …………………………………………… 4-12 4.2 Reading Demand/Response Flag ………………… 4-13 Stop operation (Command: 0000h) ………………… 4-13 Read out once (Command: 0001h) ………………… 4-14 Continuous reading out (Command: 0002h) ……… 4-15 Reading out set values to the monitor area (Command: 0003h) …………………………………… 4-16 Reading out set values to the setting area (Command: 0004h) …………………………………… 4-17 4.3 Parameter Setting Demand/Response Flag……… 4-18 Stop operation (Command: 0000h) ………………… 4-18 Write once (Command: 0001h) ……………………… 4-19 3 Installation …………………………… 3-1 Continuous writing (Command: 0002h) …………… 4-20 3.1 Installation Procedure …………………………………3-3 4.4 Command Setting Demand/Response Flag ……… 4-21 1:1 connection ……………………………………………3-3 Stop operation (Command: 0000h) ………………… 4-22 1:N connection ……………………………………………3-5 Communication restoration demand 3.2 Dimensions ……………………………………………3-7 (Command: FFFFh) …………………………………… 4-23 External dimension ………………………………………3-7 4.5 Command Execution Example …………………… 4-24 3.3 Mounting Modules ……………………………………3-8 Memory setting ………………………………………… 4-24 How to attach/detach the front terminal block/ Reading out parameters ……………………………… 4-26 the base part from the main unit ………………………3-8 Reading out set values to the monitor area ………… 4-27 Mounting to DIN Rails ………………………………… 3-10 Reading out set values to the setting area ………… 4-28 Order of modules ……………………………………… 3-12 Writing set values ……………………………………… 4-29 INP-TN5A0202-E 5 5 System Configuration …………… 5-1 Communication Parameters ………………………… 5-59 5.1 Programless Communication Module Configuration Parameters …………………………… 5-62 Operation Setting ………………………………………5-3 Programless communication module station number configuration switch ……………………5-3 Operation setting when a programless communication fault occurs ……………………………5-4 5.2 Memory Setting …………………………………………5-5 Memory area ………………………………………………5-5 Setting area definition ……………………………………5-5 Communication parameter entry (Setting area) ………5-6 Monitor area definition ……………………………………5-8 Communication parameter entry (Monitor area) ………5-9 Monitor Parameters …………………………………… 5-62 5.7 Setting/Monitor Area Entry Numbers (Event I/O module) ………………………………… 5-64 Operation Parameters ………………………………… 5-64 Digital Input Parameters ……………………………… 5-65 Digital Output Parameters …………………………… 5-66 Communication Parameters ………………………… 5-69 Configuration Parameters …………………………… 5-69 Monitor Parameters …………………………………… 5-70 Internal DO Data Area ………………………………… 5-70 5.8 Setting/Monitor Area Entry Numbers 5.3 PLC Communication Setting ……………………… 5-11 (Analog module) …………………………………… 5-71 PLC communication speed setting ………………… 5-11 Operation Parameters ………………………………… 5-71 PLC transmission setting …………………………… 5-12 Setup Parameters …………………………………… 5-72 MC protocol setting …………………………………… 5-13 System Parameters …………………………………… 5-74 Setting for PLC communication starting time ……… 5-14 Alarm Parameter ……………………………………… 5-77 PLC communication inter-cycle setting …………… 5-14 Communication Parameters ………………………… 5-78 PLC communication fault detection setting ………… 5-15 Configuration Parameters …………………………… 5-81 Connection method …………………………………… 5-16 Monitor Parameters …………………………………… 5-81 Number of connected units …………………………… 5-16 MC protocol frame types ……………………………… 5-17 6 Loader Communications ………… 6-1 5.4 Status Display ……………………………………… 5-18 6.1 Loader Communication Functions ……………………6-3 Communication module status ……………………… 5-18 Connection with PC ………………………………………6-3 Programless communication status ………………… 5-19 6.2 Loader Communication Specifications ………………6-4 5.5 Address Map and Data Format …………………… 5-21 Loader interface …………………………………………6-4 Programless communication module status ……… 5-21 6.3 Loader Connection ……………………………………6-5 Communication status with PLC …………………… 5-21 Communication terminal …………………………………6-5 PLC communication setting ………………………… 5-22 Connection with a loader communication port ………6-5 Programless communication module 6.4 Setting Loader Communication Parameters ………6-6 operation setting ……………………………………… 5-22 Setting items for loader interface (The equipment) …6-6 Memory configuration (Setting area) ………………… 5-23 6.5 MODBUS Communication Protocol …………………6-7 Memory configuration (Monitor area) ……………… 5-24 Message composition ……………………………………6-9 Register number order ……………………………… 5-25 Error Check Code (CRC-16) Calculation …………… 6-12 5.6 Setting/Monitor Area Entry Numbers Transmission control procedure …………………… 6-13 (Control module) …………………………………… 5-51 6.6 Command and Transmission Frame Details …… 6-15 Operation parameter ………………………………… 5-51 Reading Data ………………………………………… 6-15 Control (PID) Parameters …………………………… 5-52 Writing Data …………………………………………… 6-20 Setup Parameters …………………………………… 5-53 System Parameters …………………………………… 5-54 Alarm Parameters …………………………………… 5-58 6 INP-TN5A0202-E 7 Trouble Shooting …………………… 7-1 7.1 Error Procedure…………………………………………7-3 Troubles during operation ………………………………7-3 Troubles during connecting the loader …………………7-7 Index ………………………………………… 1 INP-TN5A0202-E 7 8 INP-TN5A0202-E 1 Overview 1.2 Model Code ………………………………… 1-4 1.3 Part Names and Functions ……………… 1-5 3 Installation Overview …………………………………… 1-3 2 System Configuration Example 1.1 4 Programless Communication Operation 5 System Configuration 6 Loader Communications 7 Trouble Shooting 1-1 INP-TN5A0202-E Overview 1 1.1 Overview 1-2 INP-TN5A0202-E 1.1 Overview 1.1 Overview An Enhanced communication module, PUMCM is for enabling MELSEC-Q/A/AnS/FX series (hereinafter referred to as PLC) produced by Mitsubishi’s Electric Corporation (hereinafter called PLC) and a multi-loop module type temperature controller, PUM series, to communicate each other using programless communications. Point • Programless communication is the communication method that enables to read out /write the data inside the temperature controllers (PUM series) from the PLC without making ladder programs on PLC. • There are 2 types of connection method with an enhanced communication module PUMC. One of them is 1:1(single) connection that connects a single unit of PUMCM to the communication port on PLC. The other is 1:N (multi-master) connection that connects up to 8 units of PUMCM to the communication port on PLC. Using side connectors for the enhanced communication module, PUMCM, or the temperature control module(PUM series) are connected enables a wiring to only one power terminal and a labor saving wiring. PWR BUS PUM-C LOADER RX1 TX1 STATION 45 E F0 1 23 89 67 TX2 AB RX2 CD Hereinafter, PUMCM will be also referred as to “the equipment” or “programless communication module”. Confirming Accessories Before using the product, please confirm that all of following accessories are included. Description Quantity Temperature Controller Enhanced Communication Module (The equipment) 1 unit Instruction Manual (Installation) 1 copy INP-TN5A0202-E 1-3 1.2 Model Code 1.2 Model Code Programless Communication Module 2 7 / ; ; 㧙 0 10 % / # $ Contents Module type Enhanced communication module Communication functions Mitsubishi's PLC programless communications Instruction manual Japanese English Accessories (Optional) 1 2 3 4 5 6 7 8 P U M Z * A A A L 1-4 0 0 0 0 2 3 4 1 Contents DIN rail mounting endplate Side connecting terminal covers (right & left 1set) Front face screw terminal cover Loader connecting cable (RS-232C) INP-TN5A0202-E 1.3 Part Names and Functions 1.3 Part Names and Functions External View Main body PWR PUM-C BUS Base part LOADER RX1 TX1 STATION 45 E F0 1 23 89 67 TX2 AB RX2 CD Front terminal block Front Terminal Block The front terminal block consists of screw terminals, a loader communication port, a station No. configuration switch and LED indicator lamps. • The front terminal block is removable from the main body through one-touch operation. Main Body It is the main body of a module containing circuits for programless communications. • The main body is removable from the base part through one-touch operation. • Communication behavior configuration switches are on the back face (the base part). Base Part The base part consists of power terminals, module connectors for connecting modules and the structure of fixing a module to DIN rails. INP-TN5A0202-E 1-5 1.3 Part Names and Functions Front Terminal Block PWR PUM-C BUS LOADER .QCFGTEQOOWPKECVKQPRQTV RX1 TX1 STATION 345 6 E 5VCVKQP0Q EQPHKIWTCVKQPUYKVEJ 7 8 9A TX2 F012 RX2 BCD .'&KPFKECVQTNCORU +1VGTOKPCNDNQEM LED Indicator Lamps LED lamps indicate the following operational conditions. LED Green Red Orange Blinking (0.4-sec. inter-cycle): No communications with any modules (inter-module communication FAULT) PWR Blinking (0.1-sec. inter-cycle): ON: No communication with PLC (inter-PLC communication ― FAULT) Executing initial polling Blinking (0.4-sec inter-cycle): Waiting communication System FAULT (*Note 1) during 1:N connection ON: RUN BUS ON: Inter-module communication being received ― RX1 ON: RS-232C/RS-485 being received ― TX1 RX2 TX2 ― ON: RS-422 being received ― ― ON: Inter-module communication being sent ― ON: RS-232C/RS-422/RS-485 being sent ― ― ― ― *Note 1: Sources of system faults: EEPROM FAULT, Station No. configuration SW FAULT, DIP SW FAULT 1-6 INP-TN5A0202-E 1.3 Part Names and Functions Loader communication port Connecting the equipment to the PC that is installed PUM parameter loader software with a loader connecting cable (optional). Station No. configuration switch Set 0 to 7 according to the PLC connection method (1:1 connection or 1:N connection). Note • When performs programless communication with 1:1 connection, make sure to set "0" to the station number of this equipment. Otherwise, this equipment can not perform communication with PLC. • When performs programless communication with 1:N connection, make sure to set station numbers of this equipment in order, from "0". If there are missing numbers with the station numbers, this equipment can not perform communication normally with PLC. INP-TN5A0202-E 1-7 1.3 Part Names and Functions Main part (Back face) 10 1 2 3 4 5 6 %QOOWPKECVKQP DGJCXKQTUGVVKPI Communication behavior configuration Switch Communication behavior is set by DIP switch (SW1 to SW6) on the back face of the module. Communication behavior SW setting 1(Note 1) 2(Note 1) 3 4 5 RS-232C OFF OFF OFF OFF OFF RS-422 ON OFF OFF OFF OFF RS-485 OFF ON OFF OFF OFF 6 (Note 2) (Note 1): Turning SW1 and SW2 ON at the same time is not possible. (Note 2): If turning the SW6 ON, communication setting operates with the factory-set value. Factory-set value of the communication setting is as follows. 1-8 Parameter Set value Remarks column Communication speed 115.2kbps PLC communication speed setting Data bit 8 Parity EVEN Stop bit 1 PLC transmission setting 5-11 5-12 INP-TN5A0202-E 1.3 Part Names and Functions Base Part Mounting screw hole Module connector Module connector Power terminal block Mounting screw hole Locking tab Module connector These connectors are for connecting modules laterally. Power terminal block The power terminal block is for connecting the equipment to a module’s power supply. Connection with the only one module enables all modules to be supplied power via module connectors. Locking tab The locking tab is for fastening a module to DIN rails and fastening each module connected laterally when mounting a module to DIN rail. INP-TN5A0202-E 1-9 1.3 Part Names and Functions 1-10 INP-TN5A0202-E 1 Overview 3 Installation 4 Programless Communication Operation 5 System Configuration 6 Loader Communications 7 Trouble Shooting 2-1 INP-TN5A0202-E System Configuration Example ………… 2-3 2.1 2 System Configuration Example 2 System Configuration Example 2.1 System Configuration Example 2-2 INP-TN5A0202-E 2.1 System Configuration Example 2.1 System Configuration Example The figure below shows the example of system configuration connecting PLC and the multi-loop module type temperature controller. • Data in a control module/an event module is possible to read out/write from/into PLC using a programless communication module. 1:1 Connection • The minimum configuration by using 1 unit of programless communication module and a communication port on PLC. • Connection of up to 16 units of control/analog module and 16 units of event module is configurable. • Usable PLCs are MELSEC-Q/A/AnS/FX series, and usable interfaces are RS-232C/RS-422/RS-485. MELSEC-Q series connection example Connect to a control module (the master of inter-module communications)/ Programless communication module Windows PC (PUM parameter loader) CPU unit Loader connecting cable (Connect to a master module) Communication unit MELSEC-Q series Internal communication Enhanced communication module INP-TN5A0202-E Control module + Analog I/O module (Total max.: 16 units) Event I/O module (Total max.: 16 units) 2-3 2.1 System Configuration Example Point ● Distributed placement of module-type temperature controller system is possible by connecting several communication units to PLC and connecting programless communication modules to each of them. ● Control or Analog I/O module station number (“1” to “16”) For proper communication, station number configuration is required. Set the leftmost module to “1” and set the rest of modules to “2” to “16” consecutively starting from the left. Make sure not to duplicate station numbers in the system. ● Event I/O module station number (“17” to “32”) Event I/O module station number always starts from “17” and be set to the rest of unit consecutively form “18” to “32”. Make sure not to duplicate station numbers in the system. ● To use a programless communication module, “connection permission of enhanced communication module (PUMC)” parameter should be set to “1: PUMC connected (RS-485:disable)” with the PUM parameter loader. Note Using PLC/MC protocol are different from the usable communication interface for MC protocol frame type. Refer to "MC protocol frame types" 5-17 for details. Basic Setting Items With this configuration, the following settings are required. ● Communication module station number setting ● Memory setting 5-5 ● PLC communication setting ● Connection method 5-11 5-16 ● Number of connected units ● MC protocol setting ● MC protocol frame types 5-16 5-13 5-17 ● RS-485 communication setting 2-4 5-3 ”Control module user’s manual” INP-TN5A0202-E 2.1 System Configuration Example 1:N Connection • This is the configuration using 2 to 8 units of programless communication modules and a communication port of PLC. This configuration enables you to control more units of PUM series by 1 unit of PLC. • Configuration with up to 128 units (512ch) of control/analog modules and 128 units of event modules by only 1 communication port is possible. • Usable PLC is MELSEC-Q/A/AnS series. Configuration by using FX series is not possible. MELSEC-Q series connection example Connect to a control module (the master of inter-module communications)/ Programless communication module Windows PC (PUM parameter loader) CPU unit Loader connecting cable (Connect to a master module) Communication unit MELSEC-Q series Internal communication Enhanced communication module Control module + Analog I/O module (Total max.: 16 units) ع ع ع ع RS-422/RS-485 connection Event I/O module (Total max.: 16 units) Max. 8 systems (Enhanced communication module: Max. 8 units) Internal communication Enhanced communication module INP-TN5A0202-E Control module + Analog I/O module (Total max.: 16 units) Event I/O module (Total max.: 16 units) 2-5 2.1 System Configuration Example Point ● Distributed placement of module temperature control system is possible by 1:N connection. ● Control or Analog I/O module station number (“1” to “16”) For proper communication, station number configuration is required. Set the leftmost module to “1” and set the rest of modules to “2” to “16” consecutively starting from the left. Make sure not to duplicate station numbers in the system. ● Event I/O module station number (“17” to “32”) Event I/O module station number always starts from “17” and be set to the rest of unit consecutively form “18” to “32”. Make sure not to duplicate station numbers in the system. ● To use a programless communication module, “connection permission of enhanced communication module (PUMC)” parameter should be set to “1: PUMC connected (RS-485:disable)” with the PUM parameter loader. Note ● MELSEC-FX series can not perform communication with 1:N connection. ● 1:N connection of RS-232C can not be configured. ● When MC protocol is type 4, 1:N connection is not possible. ● When using 1:N connection, PLC communication setting should be matched to the settings of all programless communication modules. Basic Setting Items With this configuration, the following settings are required. ● Communication module station number setting ● Memory setting 5-5 ● PLC communication setting ● Connection method 5-11 5-16 ● Number of connected units ● MC protocol setting ● MC protocol frame types 5-16 5-13 5-17 ● RS-485 communication setting 2-6 5-3 ”Control module user’s manual” INP-TN5A0202-E 1 Overview 2 System Configuration Example 3 Installation 3.2 Dimensions ………………………………… 3-7 3.3 Mounting Modules ………………………… 3-8 3.4 Attaching Accessories (Optional) ……… 3-13 3.5 Mounting with Screws …………………… 3-14 3.6 Connection ………………………………… 3-15 4 Programless Communication Operation Installation Procedure …………………… 3-3 3 Installation 3.1 5 System Configuration 6 Loader Communications 7 Trouble Shooting INP-TN5A0202-E 3-1 3.1 Installation Procedure 3-2 INP-TN5A0202-E 3.1 Installation Procedure 3.1 Installation Procedure The flowchart below shows the setting procedure for startup via PUM parameter loader. 1:1 connection • Connection permission for an enhanced communication module should be set to "1: PUMC connected (RS-485 disable)" with all temperature control modules of the system. (Control/Event/Analog module) • When setting parameters for a programless communication module, connect PUM parameter loader to it directly. 1 Installation Confirm installation dimensions ● 3-7 External dimensions Decide installation method ● DIN rail mounting 3-10 ● Mounting with screws 3-14 Connect the temperature control module performs communication with PLC on the right of the programless communication module. ● 2 Connecting modules 3-11 Wiring It is for power supply to the connection between a programless communication module and PLC, and a programless communication module. Turn OFF all the power of the equipment or any other modules, when wiring. ● Connection with PLC 3-15 ● Wiring for power supply 3-23 See “User's manual” of your PLC for wiring of PLC. 3 Station number configuration Configure the St. No. of a programless communication module. ● 4 Configure St. No. to “0” by using the St. No. configuration switch on the front face. 1-7 Loader soft preparations for PUM Prepare a PC where PUM parameter loader has installed and a loader connecting cable to connect PC, a programless communication module and a temperature control module. See “Parameter loader for PUM user’s manual”. 5 Temperature control module setting Set the “enhanced communication module (PUMC) connection permission” parameter of the temperature control module connected to a programless communication module to “1: PUMC connected (RS-485: disable)”. See Instruction Manual "Parameter loader for multi-loop module-type temperature controller (PUM)" for PUM parameter loader connection method and parameter setting. * When setting parameters of a temperature control module, connect PUM parameter loader directly to the loader communication port on a temperature control module. In the case of a single-unit connection, connect PUM parameter loader directly to a single unit, and in the case of connection of connected units, connect PUM parameter loader directly to the module set as "Master" with "connected modules master/slave setting" parameter. Go to the next page INP-TN5A0202-E 3-3 3.1 Installation Procedure Continued from the previous page 6 Programless communication module setting This setting is for performing communication between a programless communication module and PLC. ● Communication setting 5-3 ● Connection method Set “0 1:1 connection” for the connection method. 5-16 ● Connected units Set “1” for the No. of connected units. 5-16 Register parameters of the temperature control module that reads/writes form PLC. ● Memory setting 5-5 to 5-10 ● PLC communication setting 5-11 to 5-17 * When setting the parameters of a programless communication module, connect a parameter loader for PUM directly to the loader communication port on the programless communication module. 7 PLC setting This setting is for communication-related parameters for PLC or DIP SW setting. See “User’s manual” of your PLC for details of setting 8 Operation command by a programless communication module This command is for setting communication the communication behavior between a programless communication module and PLC. ● 3-4 Programless communication behavior 4-3 to 4-23 INP-TN5A0202-E 3.1 Installation Procedure 1:N connection • Connection permission for an enhanced communication module should be set to "1: PUMC connected (RS-485 disable)" with all temperature control modules in the system (Control/Event/Analog module). • When setting parameters for a programless communication module, connect PUM parameter loader to it directly. 1 Installation Confirm installation dimensions ● 3-7 External dimensions Decide installation method and install. ● DIN rail mounting 3-10 ● Mounting with screws 3-14 Connect the temperature control module performs communication with PLC on the right of the programless communication module. ● 2 3-11 Connecting modules Wiring It is for power supply to the connection between a programless communication module and PLC, and a programless communication module. Turn OFF all the power of the equipment or any other modules, when wiring. ● Connection with PLC 3-15 ● Wiring for power supply 3-23 See “User's manual” of your PLC for wiring of PLC. 3 Station number configuration Configure the St. No. of a programless communication module. ● 4 Configure St. Nos. by using the St. No. configuration switch on the front face. 1-7 Loader soft preparations for PUM Prepare a PC where PUM parameter loader has installed and a loader connecting cable to connect PC, a programless communication module and a temperature control module. See “Parameter loader for PUM user's manuall” 5 Temperature control module setting Set the “enhanced communication module (PUMC) connection permission” parameter of the temperature control module connected to a programless communication module to “1: PUMC connected (RS-485: disable)”. See Instruction Manual “Parameter loader for multi-loop module-type temperature controller (PUM)” for PUM parameter loader connection method and parameter setting. * When setting parameters of a temperature control module, connect PUM parameter loader directly to the loader communication port on a temperature control module. In the case of a single-unit connection, connect PUM parameter loader directly to a single unit, and in the case of connection of connected units, connect PUM parameter loader directly to the module set as "Master" with "connected modules master/slave setting" parameter. Go to the next page INP-TN5A0202-E 3-5 3.1 Installation Procedure Continued from the previous page 6 Programless communication module setting This setting is for each programless communication module in order to perform communication between a programless communication module and PLC. ● Communication setting 5-3 ● Connection method Set “1 1:N connection” for the connection method. 5-16 Connected units 5-16 ● Set the No. of connected units of programless communication modules for the No. of connected units. Register parameters of the temperature control module that reads/writes from PLC to each programless communication module. ● Memory setting 5-5 to 5-10 ● PLC communication setting 5-11 to 5-17 * Communication settings for all of programless communication modules should be same. When setting the parameters of a programless communication module, connect a parameter loader for PUM directly to the loader communication port on the programless communication module. 7 PLC setting This setting is for communication-related parameters for PLC or DIP SW setting. See “User’s manual” of your PLC for details of setting 8 Operation command by a programless communication module This command is for setting communication the communication behavior between a programless communication module and PLC. ● 3-6 Programless communication behavior 4-3 to 4-23 INP-TN5A0202-E 3.2 Dimensions 3.2 Dimensions External dimension Provide enough clearance space for installation referring to the diagram below. Front screw terminal cover (optional) Terminal block (When detached from the main unit) 30 PWR Base part (When detached from the main unit) (10) 85 PUM-C LOADER BUS RX1 TX1 345 6 100 50 E 7 8 9A F012 6 TX2 1.5 BCD RX2 STATION 6.1 DIN rail Terminal screw (M3) (30) When mounting/ dismounting to DIN rail (8) 5 Terminal screw (M3) Main body ( When detached from the base part) Unit [mm] Cautions when installing In order to heat dissipation, provide clearance space of more than 30mm (50mm is recommended) above and under the 30 or more 30 or more equipment. Unit [mm] Point Clearance space more than 30mm above and under a module should be provided when mounting/dismounting it to/from DIN rails. INP-TN5A0202-E 3-7 3.3 Mounting Modules 3.3 Mounting Modules How to attach/detach the front terminal block/the base part from the main unit Each module of Multi-Loop Module Type Temperature Controller, PUM series, has the configuration that both the front terminal block and the base part are detachable through one-touch operation for easy installation and maintenance. How to detach the front terminal 1. Press the lock lever on the top of the main unit. 2. Pull down the front terminal block. 3. Detach the cutout at the lower end of the front terminal Lock lever block from the projection on the main unit. Point Front terminal block ● Attaching the main unit to the base part takes the reverse procedure to removing the main unit from the base part. ● Make sure the locking lever on the main unit is fitted into the base part when attaching is completed. Main unit Main unit Projection 3-8 INP-TN5A0202-E 3.3 Mounting Modules How to detach the base part 1. Press the Lock lever on the top of the main unit. 2. Pull down the main unit. 3. Remove the cutout at the lower end of the main unit from Lock lever the projection on the base part. Point ● Attaching the base part to the main unit takes a reverse procedure to detaching the base part from the main unit. Base part ● Make sure the locking lever on the main unit is fitted into the base part when attaching is completed. Main unit ࡌࠬㇱ Main unit Projection INP-TN5A0202-E 3-9 3.3 Mounting Modules Mounting to DIN Rails Mounting modules 1. Pull down the locking tab of the base part. Hook the back part of the module onto the upper part of the DIN rails. 2. Push the module towards the direction of the arrow 2. Hook DIN rail Locking tab 3. Pull up the locking tab of the base part to fasten the module onto the DIN rails. Point When connecting the module after mounting it to the DIN rail, pull the locking tab up after connecting modules each other. 3-10 INP-TN5A0202-E 3.3 Mounting Modules Connecting modules PUM-C BUS LOADER TX1 OUT2 STATION STATION 6 OUT4 7 8 9A 7 8 9A E 345 OUT3 345 6 TX2 LOADER COM OUT1 RX2 PUM-A PWR RX1 F012 each other. PWR E Connect modules by connecting module connectors with F012 2. BCD Check the locking tab is pulled down. BCD 1. Module connector Locking tab 3. After mounting modules to the DIN rails, pull the all locking tabs up. PUM-A COM LOADER PWR PUM-A COM LOADER OUT1 TX1 OUT2 OUT2 F012 F012 345 OUT3 OUT4 STATION 345 7 8 9A E STATION 7 8 9A 7 8 9A OUT4 6 OUT3 6 345 E STATION 6 BCD RX2 TX2 4. PWR OUT1 F012 LOADER RX1 E PUM-C BUS BCD on the same time. PWR BCD Modules are fastened to the DIN rails and to each other The power supplies are connected each other inside connected modules. INP-TN5A0202-E 3-11 3.3 Mounting Modules Order of modules Connecting a multi-loop module type temperature controller, PUM series, is shown as below. Programless communication module Control module + Analog I/O module LOADER RX1 PWR PUM-A PWR COM LOADER COM OUT1 TX1 OUT2 “2” .......... “16”(Max.) F012 F012 LOADER STATION 345 7 8 9A “1”(Master) &Q &Q &Q &Q &Q &Q &Q &Q 6 BCD E 345 7 8 9A OUT4 6 “128”(fixed) OUT3 E 345 7 8 9A TX2 6 RX2 STATION BCD STATION PUM-E &K &K &K &K &K &K &K &K F012 PUM-C BUS Slave E PWR Event I/O module BCD Control module (Master) “17” “18” .......... “32”(Max.) Station No. Point A programless communication module is always placed on the extreme left. ● An programless communication module should be on the left of the master control module: it is always placed on the left. Modules are basically placed in the order of station numbers starting from the left. ● Set station number “1” to “16” to control modules and analog I/O modules. Max. 16 units are connectable. Make sure not to duplicate station numbers in the same system. ● When setting a master/a slave, the control module set to “1” should be a master. When not using a programless communication modules, a master module should be placed on the extreme left of the system. ● Set station numbers for event I/O modules to “17” to “32”. Max. 16 units are connectable.Make sure not to duplicate station numbers in the same system. 3-12 INP-TN5A0202-E 3.4 Attaching accessories (optional) 3.4 Attaching accessories (optional) Attaching side connecting terminal covers Side connectors on both ends of connected modules are 345 PUM-E &K &K &K &K &K &K &K &K &Q &Q &Q &Q &Q &Q &Q &Q LOADER STATION 345 F012 COM E PWR LOADER F012 F012 PUM-E STATION 7 8 9A &Q &Q &Q &Q &Q &Q &Q &Q E 345 &K &K &K &K &K &K &K &K 6 F012 COM 7 8 9A E PWR LOADER 6 012 4 PUM-E STATION 7 8 9A &Q &Q &Q &Q &Q &Q &Q &Q 6 OUT4 7 8 9A 2 BCD 3E F 345 OUT3 BCD 345 &K &K &K &K &K &K &K &K E COM STATION 7 8 91 6 0 A TX2 recommended. PWR LOADER OUT2 STATION RX2 PUM-A COM OUT1 TX1 6 attaching side connecting terminal covers (PUMZ * A03) is PWR LOADER RX1 BCD PUM-C BUS BCD PWR BCD exposed. To prevent accidents and protect connectors, Side connecting terminal cover (right & left 1 set) Attaching endplates In order to fix the equipment to a DIN rail more tightly, optional endplates (PUMZ * A02) can be used. COM 3456 &K &K &K &K &K &K &K &K &Q &Q &Q &Q &Q &Q &Q &Q PUM-E PWR LOADER COM STATION 2 3456 PUM-E &K &K &K &K &K &K &K &K &Q &Q &Q &Q &Q &Q &Q &Q LOADER DIN rail mounting endplate STATION 2 3456 F01 F012 BCD E PWR LOADER 2 789 F012 PUM-E STATION 789 &Q &Q &Q &Q &Q &Q &Q &Q 789 7 8 9A BCD E 6 7 8 9A OUT4 &K &K &K &K &K &K &K &K F01 COM 345 F01 PWR LOADER STATION OUT3 BCDE 345 6 TX2 PUM-A COM OUT2 STATION A PWR OUT1 TX1 RX2 BCDE LOADER RX1 A PUM-C BUS BCDE PWR A DIN rail mounting endplate Note When attaching endplates, make sure to attach side Side connecting terminal cover (right & left 1 set) connecting terminal covers prior to them. INP-TN5A0202-E 3-13 3.5 Mounting with screws 3.5 Mounting with screws When mounting modules with screws on the wall, check for the base parts of it beforehand. Point Mounting screws are not included the product. If necessary, prepare two screws (M3) per unit. 1. Refer to the right figure for mounting screw hole size and 2-M3 (30) 9 0.2 (3) (100) 88.5 0.2 the pitch, to decide the mounting position. +0.2 30+0.7 Unit [mm] 2. Remove the module main unit from the base part. [3.3Mounting modules] 3-8 3. Connect the base parts and push the all locking tabs up to fix. 4. Fixate the base parts onto the mounting position with screws. 5. Fixate the base parts onto the mounting position with screws. 3-14 INP-TN5A0202-E 3.6 Connection 3.6 Connection Connection with PLC Connect a Multi-loop module-type temperature controller PUM series to a PLC via the programless communication module. Connectable MELSEC series MELSEC-Q series Communication port Device Q-compatible serial communication unit Type CH1 CH2 QJ71C24, QJ71C24N RS-232C (D-sub 9P) RS-422/485 (2 piece socket block) QJ71C24-R2, QJ71C24N-R2 RS-232C (D-sub 9P) RS-232C (D-sub 9P) QJ71C24N-R4 RS-422/485 (2 piece plug-in connector socket block) RS-422/485 (2 piece plug-in connector socket block) MELSEC-A/AnS series Communication port Device A-compatible computer link module Type CH1 CH2 AJ71UC24 RS-232C (D-sub 9P) RS-422/485 (terminal block) ― A1SJ71UC24-R2 RS-232C (D-sub 9P) ― RS-422/485 (terminal block) ― RS-232C (D-sub 9P) ― AnS-compatible A1SJ71UC24-R4 computer link module A1SJ71UC24PRF INP-TN5A0202-E 3-15 3.6 Connection MELSEC-FX series Communication port Device Type CH1 CH2 FX0N-232ADP RS-232C (D-sub 25P) ― FX2NC-232ADP RS-232C (D-sub 9P) ― RS-232C (D-sub 9P) ― ― RS-232C (D-sub 9P) *1 FX-232ADP RS-232C (D-sub 25P) ― FX0N-485ADP RS-485 (terminal block) ― FX2NC-485ADP RS-485 (European terminal block) ― RS-485 (European terminal block) ― ― RS-485 (European terminal block) *1 FX-485ADP RS-485 (terminal block) ― FX1N-232-BD RS-232C (D-sub 9P) ― FX2N-232-BD RS-232C (D-sub 9P) ― FX3U-232-BD RS-232C (D-sub 9P) ― FX1N-485-BD RS-485 (European terminal block) ― FX3U-485-BD RS-485 (European terminal block) ― FX3U-232ADP Communication special adapter FX3U-485ADP Enhanced board *1 When using it as CH2, FX3U- U -ADP should be connected to CH1by using FX3U- -BD or two of FX3U- U -ADP should be connected to CH1 by using an enhanced board, FX3U-CNV-BD (one of 232, 422, 485 or USB goes into , and 232 or 485 goes into U). Refer to [Data Communication Edition] in the FX SERIES USER'S MANUAL for details. Connectable model types on FX series sequencers are shown below. Type Connection FX2(FX), FX2C, FX2N, FX1N, FX2NC, FX1NC, FX3U, FX3UC Connectable FX1S, FX0N Not connectable 3-16 INP-TN5A0202-E 3.6 Connection 1:1 connection (MELSEC-Q series connection example) MELSEC-Q/A/AnS/FX series Communication unit RS-232C/RS-422/RS-485 PUMCM PUMA 1:N connection (MELSEC-Q series connection example) MELSEC-Q/A/AnS/FX series Communication unit RS-422/RS-485 PUMCM PUMA ع ع ع ع RS-422/RS-485 Max. 8 systems (Enhanced communication module : Max. 8 units) PUMCM PUMA INP-TN5A0202-E 3-17 3.6 Connection Warning Connect/separate PUM series, Temperature control system to/from PLC after turning OFF the power of the equipment or peripheral equipments to prevent electric shock and equipment failure. Point The communication speed and the maximum transmission distance are shown as below. The communication speed and the maximum transmission distance Communication speed setting Communication distance 9.6kbps 19.2kbps RS-422/RS-485 Max. 1km RS-232C Max. 15m 38.4kbps 57.6kbps 115.2kbps Max. 500m Max. 250m 230.4kbps 5-11 *Refer to “5.3 PLC communication setting” for details about communication speed . Setting of MELSEC-Q series The communication setting below is necessary to connect a programless communication module and PLC. Start GX-Developer, double click “parameter” – “PC parameter” in the project tree, and then select “I/O allocation setting”. Click “switch setting” and set the communication port of the MELSEC-Q series (serial communication unit) used as the table below. CH SW No. Bit position Contents b0 b2 b3 CH1 SW1 b4 b5 b6 Transmission setting b1 b7 SW2 Independence Linkage *1 Data bit 7 8 ON (fixed) Parity bit No Yes *1 Odd Even *1 Stop bit 1 2 *1 Sum check code No Yes ON (fixed) Write during RUN Forbidden Permitted ON (fixed) Setting change Forbidden Permitted ON (fixed) — — *2 — — 5 (fixed) Independence Linkage *1 CH1 communication protocol setting Behavior setting b4 b5 b6 b7 Transmission setting b3 Data bit 7 8 ON (fixed) Parity bit No Yes *1 Odd/Even parity Odd Even *1 Stop bit 1 2 *1 Sum check code No Yes ON (fixed) Write during RUN Forbidden Permitted ON (fixed) Setting change Forbidden Permitted ON (fixed) b8 – b15 Communication speed setting — — *2 SW4 — CH2 communication protocol setting — — 5 (fixed) SW5 — Station No. configuration — — 0 (fixed) *1…Set this as same as “PLC transmission setting” parameters 5-12 *2…Set this as same as “PLC communication speed setting” parameters module. 3-18 Set value Odd/Even parity — b2 Common CH Behavior setting Communication speed setting b1 CH2 ON b8 – b15 b0 SW3 OFF of a programless communication module. 5-11 of a programless communication INP-TN5A0202-E 3.6 Connection Setting of MELSEC-A series Refer to the Instruction Manual of Computer link module for setting. Ex.) A1SJ71UC24-R4 Transmission specification setting switch SW State Setting items OFF ― ON ― Set value 1 Not used — 2 Select Computer/Multi-drop link Not settable Computer link ON (fixed) 3 Not used ― ― — 4 Write during RUN No Yes ON (fixed) 5 6 Transmission speed *3 *1 7 8 Data bit setting 7 bits 8 bits ON (fixed) 9 Parity bit No Yes *2 10 Odd/Even parity setting Odd Even *2 11 Stop bit setting 1 bit 2 bits *2 12 Sum check No Yes ON (fixed) *1 Same setting should be made as "PLC communication speed setting" parameters communication module. *2 Same setting should be made as "PLC transmission setting" parameters module. 5-12 5-11 of a programless of a programless communication *3 Transmission speed setting Setting SW 9600 19200 Setting forbidden 5 ON OFF ON 6 OFF ON ON 7 ON ON ON St. No. configuration SW Name Contents Set value ×10 Set the tenths place digit 0 (fixed) ×1 Set the ones place digit 0 (fixed) Mode setting SW SW 0 Not available 1 Not available 2 Not available 3 Not available 4 Not available 5 Not available 6 Dedicated protocol Type2 7 Not available 8 Dedicated protocol Type4 9 to F INP-TN5A0202-E Setting Not available 3-19 3.6 Connection Setting of MELSEC-FX series Start up GX-Developer, double-click [parameter] - [PC parameter] in the project tree, and then double-click [PC system setting (2)] in the dialog box. Select a desired channel, mark the "communication setting"check box, and then make a setting of the communication port of your MELSEC-FX series as the following table. Setting items Protocol Setting Dedicated protocol communication (fixed) Data length 8 bits (fixed) Parity *1 Stop bit *1 Transmission speed Sum check *2 With RS-232C: Normal/RS-232C With RS-485: RS-485 Yes (fixed) Transmission control procedure Type 4 (CR, LF (fixed)) H/W type St. No. setting 0 (fixed) Timeout determination time 1 (default setting) 5-12 *1 Same setting should be made as "PLC transmission setting" parameters module. of a programless communication *2 Same setting should be made as "PLC communication speed setting" parameters communication module. 5-11 of a programless Terminal PWR PUM-C BUS LOADER RX1 TX1 vacant vacant A B SG A(SD) B(SD) SG A(RD) B(RD) TX RX SG STATION 345 F012 TX2 E RS-232C 7 8 9A RS-422 6 RS-485 BCD RX2 21 11 22 12 23 13 24 14 25 15 26 16 27 17 vacant vacant 28 18 29 19 30 20 vacant vacant Point Communication terminal numbers and signal contents ● The insulation between terminals is as follows. Before installing, confirm that the insulation for the equipment meets usage requirement. Power supply Loader communication Functional insulation (AC1000V) 3-20 RS-232C communication RS-422 communication RS-485 communication Functional insulation (AC500V) INP-TN5A0202-E 3.6 Connection Connection with PLC RS-232C connection Communication unit Pin No. 1 2 3 4 5 6 7 8 9 This unit Signal CD RD(RXD) SD(TXD) ER(DTR) SG DR(DSR) RS(RTS) CS(CTS) RI(CI) Pin No. 21 22 23 24 25 26 27 28 29 30 Signal TX RX SG A B SG A B – – RS-422 connection 1:1 connection Communication unit Terminating resistance Terminating resistance This unit Signal SDA SDB RDA RDB SG FG Pin No. 21 22 23 24 25 26 27 28 29 Signal TX RX SG A B SG A B − Terminating resistance Terminating resistance 1:N connection Communication unit Terminating resistance Terminating resistance This unit 1 Signal SDA SDB RDA RDB SG FG RS-422/RS-485 cable INP-TN5A0202-E Pin No. 21 22 23 24 25 26 27 28 29 30 This unit 2 Signal TX RX SG A B SG A B – – Pin No. 21 22 23 24 25 26 27 28 29 30 Signal TX RX SG A B SG A B – – Terminating resistance Terminating resistance 3-21 3.6 Connection RS-485 connection 1:1 connection Communication unit This unit Signal SDA SDB RDA RDB SG FG Terminating resistance RS-422/RS-485 cable Pin No. 21 22 23 24 25 26 27 28 29 30 Signal TX RX SG A B SG A B – – Terminating resistance 1:N connection Communication unit This unit 1 Signal SDA SDB RDA RDB SG FG Terminating resistance RS-422/RS-485 cable Pin No. 21 22 23 24 25 26 27 28 29 30 This unit 2 Signal TX RX SG A B SG A B – – Pin No. 21 22 23 24 25 26 27 28 29 30 Signal TX RX SG A B SG A B – – Terminating resistance Point ● Use the terminal insulation shown as below. RS-422 : 330Ω ±5% 1/2W RS-485 : 110Ω ±5% 1/2W ● This unit can not make 2 or more different communication connections operate at the same time. Connecting modules Connectable modules to the equipment are as follows. • PUMA/B (Control module), PUMV/N/T (Analog I/O module), PUME (Event I/O module) Point ● Max. 32 units are connectable to the equipment. The number of connectable modules varies according to module types. Refer to user’s manual for each module for details. ● When connected modules, power supplies are connected to other modules by connecting power supply lines to the one of the modules. 3-22 INP-TN5A0202-E 3.6 Connection Wiring for power supply Terminal layout Power terminals are on the base part of each module. Wiring is same for the all modules. The power supplies to all connected modules by connecting this terminal to the only one of them. Power terminal DC 24V (-) DC 24V (+) Note ● Wiring to a terminal block, use crimp terminal (screw size: M3). Use the screws in this product only. Screw size on the terminal block: M3×7 (with square washer) Clamp torque: 0.78N-m (8kgf-cm) ● Apply power cable with allowable current capacity larger than total consumption current of all connected modules. ● Power cable more than one should not be connected to power terminals. ● When using AWG 16 cable, you should use the crimp terminal that material thickness is 0.9mm or less. ● Use the power cables and crimp terminals indicated below for wiring. Power cable size Cable type Size 0.25 – 1.25mm2 (AWG22 to 16) Power cable, output, others Crimp terminal size Cable size Clamp torque 2 3.2mm Round-shaped crimp terminal INP-TN5A0202-E 3.2mm 0.8Nm 6.0mm or less 6.0mm or less 0.25 – 1.25mm (AWG22 to 16) * Material thickness 0.9mm or less Y-shaped crimp terminal 3-23 3.6 Connection 3-24 INP-TN5A0202-E 1 Overview 4.2 Reading Demand/Response Flag ……… 4-13 4.3 Parameter Setting Demand/Response Flag … 4-18 4.4 Command Setting Demand/Response Flag … 4-21 4.5 Command Execution Example ………… 4-24 4 Programless Communication Operation Device Memory …………………………… 4-3 3 Installation 4.1 2 System Configuration Example 4 Programless Communication Operation 5 System Configuration 6 Loader Communications 7 Trouble Shooting INP-TN5A0202-E 4-1 4.1 Device Memory 4-2 INP-TN5A0202-E 4.1 Device Memory 4.1 Device Memory The programless communication module operates as the master of the communication between PLC and the module, and reads outs/ writes PLC device memory according to the programless communication module parameters’ setting. Only accessing to this device memory enables PLC to monitor or set the data of the module type temperature controller connected to the programless communication module. Hereinafter, the communication between a programless communication module and PLC-module will be also referred as to “the programless communication”. PLC PLC Control Device memory System field Data field Reading set/monitor value Reading set value Writing set value Data field Command response Monitor area System field Command demand Setting area Programless communication module Setting area Temperature control module St.1 Temperature control module St.32 (Connectable max. units) Writing data to each temperature control module Field Set value Set value Monitor value Monitor value Monitor area Field Read out data from each temperature control module Point PLC does not need the ladder program for communications, since the programless communication module updates the device memory data automatically with the programless communication function. INP-TN5A0202-E 4-3 4.1 Device Memory How to use the device memory The setting area and the monitor area set on the PLC device memory have the system field and the data field. D0000 D1000 Reading response flag Reading demand flag D1001 System field (Each 1 word) D1002 D0001 Command setting demand flag D0002 System area 1 (Reserved) D0003 D0004 Data field Parameter setting response flag System field (Each 1 word) Command setting response flag Monitor area D1004 Setting area D1003 Parameter setting demand flag Depends on setting parameter entry (0 to 712) System area 1 (Reserved) Data field Depends on monitor parameter entry (0 to 712) D0715 D1715 The device names and the device No. on the table below is referring to the following set values. Area Device used Initial address Number of data Setting area Data register (D) 1000 712 Monitor area Data register (D) 0000 712 The setting of the device used/the address used are changeable. 5-5 Note The configuring the setting area and the number of setting area data, and the monitor area and the number of monitor area data used on the PLC memory is necessary prior to starting programless communications. 5-5 ● When using with 1:N connection, make a setting not to duplicate the setting area and the monitor area of each programless communication module. ● Make sure not to duplicate the device memory area used by PLC. 4-4 INP-TN5A0202-E 4.1 Device Memory Setting area • System field Set the flag in the system field enables the PLC to read data out or to require the setting change to the temperature control module. Item Reading demand flag Value Command Operation required 0000h Stop operation Stop the temperature control module data reading demand. 0001h Read out once Execute the process once: reading out data from the temperature control module, and updating the monitor area data field. 0002h Continuous read out Execute the process periodically: reading out data from the temperature control module, and updating the monitor area data field. Refer to “PLC communication inter-cycle setting” about the fixed-cycle time. 5-14 0003h Set value reading out to the monitor area Read out parameters’ present values entered to the setting area form the temperature control module, and update the monitor area data field. 0004h Set value reading out to the setting area Read out parameters’ present values entered to the setting area from the temperature control module, and update the setting area data field. 0000h Stop operation Stop the temperature control module data writing demand. 0001h Set once Execute the process once: writing the set value set in the setting area data filed to the temperature control module. Parameter setting demand flag 0002h Continuous setting Execute the process periodically: writing the data set in the setting area data field to the temperature control module. Refer to “PLC communication inter-cycle setting” 5-14 0000h Stop operation about the fixed-cycle time. Stop the command execution demand to the programless communication module. When the operation select is set to “Stop” with the programless communication module “Operation setting when a programless communication Command setting demand flag FFFFh Communication restoration demand fault occurs” 5-4 demand to restart operation for the programless communication module stopped with some faults. In addition, set “0000h” to the command setting demand flag, the programless communication module starts communication. System area 1 (Reserved) INP-TN5A0202-E 0000h None 4-5 4.1 Device Memory • Data field Set the data for writing to the temperature control parameter entered as setting parameters. Setting parameters are entered by "Communication parameter entry (Setting area)". 5-6 Point Before the parameter setting demand, set values to the data field used. If there are some parameters not required to be change, execute the reading demand flag=0004h (reading out set values to the setting area), and change only the parameters’ setting that is necessary. Note During 1:N connection, each programless communication module has a system field and a data field. 4-6 INP-TN5A0202-E 4.1 Device Memory Monitor area • System field The response result from the PLC to the temperature control module that is required in the setting area system field or the temperature control module status can be confirmed. Item Value Response Explanation 0000h Stop data area update/Complying with demand status Updating of the data field in the monitor area via the programless communication is in the stopped state, or the reading demand flag is in a complying with demand status. 0001h to 0004h Normal response That the response value is the same as the reading demand flag means that response to each demand is the normal response. 8001h to 8004h Demand's abnormal response Abnormal response to each demand. (The state that communication errors are occurring between temperature control modules. Such as, nonexistent units) Other than those above Abnormal response Abnormal status other than the programless communications. (Such as, device memory setting duplication, overwrite by PLC sequence program) 0000h Stop data area update/Complying with demand status Updating data field in the setting area via the programless communication is in the stopped state or the parameter setting demand flag is in the complying with demand status. 0001h to 0002h Normal response That the response value is the same as the reading demand flag means that the response to each demand is the normal response. 8001h to 8002h Demand's abnormal response Abnormal responses to each demand. (The state that communication errors are occurring between temperature control modules) The sources: such as, nonexistent units, the data out of range was written. Other than those above Abnormal response Abnormal status other than the programless communication. (Such as, device memory setting duplication, overwrite by PLC sequence program) 0000h Stop data area update/Complying with demand status In the status of complying with the command setting demand flag. EEEEh Stopped state The programless communication is in the “stopped state”. 5-4 FFFFh Restoration state The response to “communication restoration demand” is normal. Other than those above Abnormal response Abnormal status other than the programless communication. (Such as, device memory setting duplication, overwrite by PLC sequence program) 0000h None Reading response flag Parameter setting response flag Command setting response flag System area 1 (Reserved) INP-TN5A0202-E 4-7 4.1 Device Memory • Data field The present value of the temperature control module data entered as a monitor parameter is stored in this field. The monitor parameters are entered by "Communication parameter entry (Monitor area)". 5-9 Note During 1:N connection, each programless communication module has a system field and a data field. 4-8 INP-TN5A0202-E 4.1 Device Memory Operation for the programless communications 5-14 After turning the power on and passed the waiting time set by “PLC communication starting time" parameter , execute the operation with the programless communication below. Write set values to the temperature control module Write the data field’s values in the setting area to the temperature control module parameters entered to that area. PLC Device memory System field Data field Data field Writing Response Monitor area System field Writing demand Setting area Programless communication module Setting area Temperature control module St.1 Temperature control module St.32 (Connectable max. units) Writing data to each temperature control module Writing set value Field Writing Writing Set value Set value Note ● Judge if the set value changed on the temperature control module, and modify the set value only when it changed. ● Do not modify the set value of the parameter entered as the setting parameter via the loader port communication. If changed it, the value written by the PLC comes to be invalid. To make the value by PLC valid, modify it to a different value from the present one once. ● During 1:N connection, until the module which St. No. is "0" starts a communication with PLC, other modules which St. Nos. are not "0" are in the standby state. INP-TN5A0202-E 4-9 4.1 Device Memory Read out monitor values from the temperature control module Read out the data field’s values in the monitor area to the temperature control module parameters entered to that area. PLC Device memory System field Data field Data field Reading Response Monitor area System field Reading demand Setting area Reading monitor value Programless communication module Temperature control module Temperature control module St.1 St.32 (When connected max. units) Monitor value Monitor area field 4-10 Monitor value Reading data from each temperature control module INP-TN5A0202-E 4.1 Device Memory Read out set values from the temperature control module Read out the temperature control module’s set values entered onto the setting area to the setting area data filed or the monitor area data field. PLC Device memory System field Data field Data field Reading Response Monitor area System field Reading demand Setting area Reading set value Reading set value Programless communication module Temperature control module Temperature control module St.1 St.32 (When connected max. units) Setting area field Set value Set value Reading data from each temperature control module INP-TN5A0202-E 4-11 4.1 Device Memory Programless communication operating suggestions Remind the suggestions below when executing the communication to the PLC. (1) Set the device memory exists in the PLC by using the setting tool. When setting the nonexistent device memory, the PLC sequence scan diminishes in speed. (2) Set the PLC response monitoring time 5-15 to the value with enough margins in consideration for the PLC system configurations. If the programless response monitoring time is short, the programless communication doses not operate properly. (3) Each demand flag in the setting area system field should be modified from the state that both of demand flag value and the response flag value are “0000h”. Even if modifying from the state other than “0000h”, the demand flag commands are not complied. (4) When using 1:N connection, PLC communication setting 5-11 of every programless communication modules should be the same. If not, a normal communication is not possible. 4-12 INP-TN5A0202-E 4.2 Reading Demand/Response Flag 4.2 Reading Demand/Response Flag Setting commands for the system field “reading demand flag” in the device memory setting area enables the temperature control module parameters and the memory values entered as the monitor parameters to be read out to the device memory area data field. The operation results are set for the “reading response flag” in the monitor area system field in the device memory. Stop operation (Command: 0000h) If setting “0000h” for the system field “reading demand flag” in the device memory setting area, the operation that the temperature control module parameters and the memory values entered as the monitor parameters are read out to the device memory area data field in the device memory comes to a stop. PLC Device memory Setting area Monitor area System field System field Data field Data field (1) If “0000h” is set for the reading demand flag, stop reading command will be sent. (3) If completed reading out, “0000h” is set for the reading response flag Programless communication module Temperature control module Temperature control module St.1 St.32 (When connected max. units) (2) Stop reading the monitor value Monitor value Monitor area field Monitor value Reading data from each temperature control module Note ● If the reading demand flag is not set to “0000h”, the command for the reading demand flag is not complied. When modify the reading demand flag value, reset the reading demand flag to “0000h”, and then set the value again. ● Each programless communication module has a system field and data field. INP-TN5A0202-E 4-13 4.2 Reading Demand/Response Flag Read out once (Command: 0001h) Setting “0001h” for the system field “reading demand flag” in the device memory setting area enables the temperature control module parameters and the memory values entered as the monitor parameters to be read out once to the device memory area data field in the device memory. PLC Device memory Setting area Monitor area System field System field Data field Data field (1) If “0001h” is set for the reading demand flag, the reading command will be sent once (3) If completed reading out, “0001h” will be set to the reading response flag. Programless communication module Temperature control module Temperature control module St.1 St.32 (When connected max. units) (2) Read out the monitor value once. Monitor value Monitor area field Monitor value Reading data from each temperature control module After finish reading out, put the programless communication module reading demand into the standby by the stop operation command. 4-14 4-13 INP-TN5A0202-E 4.2 Reading Demand/Response Flag Continuous reading out (Command: 0002h) Setting “0002h” for the system field “reading demand flag” in the device memory setting area enables the temperature control module parameters and the memory values entered as the monitor parameters to be read out periodically to the device memory area data field in the device memory. (Refer to “PLC communication inter-cycle time” 5-14 about the periodical time) PLC Device memory Setting area Monitor area System field System field Data field Data field (1) If “0002h” is set for the reading demand flag, reading command will be sent at a constant period. (3) If completed reading out, “0002h” will be set to the reading response flag. Programless communication module Temperature control module Temperature control module St.1 St.32 (When connected max. units) (2) Reading monitor value at a constant period. Monitor value Monitor area field Execute stop operation command 4-13 state in order to stop continuous reading out. Monitor value Reading data from each temperature control module , put the programless communication module reading demand into the standby Point Internal monitor value for the programless communication module is also entered to the monitor area. The station number for the programless communication module is “128”. INP-TN5A0202-E 4-15 4.2 Reading Demand/Response Flag Reading out set values to the monitor area (Command: 0003h) Setting “0003h” for the system field “reading demand flag” in the device memory setting area enables the present parameter values entered to the setting area to be read out once from the temperature control module to the monitor area data field in the device memory. PLC Device memory Setting area Monitor area System field System field Data field Data field (1) If “0003h” is set to the reading demand flag, command of the reading set value to the monitor area will be sent once. (3) If completed reading out to the monitor area, “0003h” will be set for the reading response flag Programless communication module Temperature control module Temperature control module St.1 St.32 (When connected max. units) Setting area field (2) Reading set value to the monitor area once. Set value Set value Reading data from each temperature control module Note With execution of this command, contents of the data field in the monitor area are discarded in order to read out the set value in the format of the setting area data field to the monitor area data field. If the monitor value in the monitor area is necessary after executing command, try to read out the monitor value by the reading out command again. After reading out, execute the stop operation command communication module into the standby status. 4-16 4-13 to put the reading demand of the programless INP-TN5A0202-E 4.2 Reading Demand/Response Flag Reading out set values to the setting area (Command: 0004h) Setting “0004h” for the system field “reading demand flag” in the device memory setting area enables the present parameter values entered to the setting area to be read out once from the temperature control module to the setting area data field in the device memory. PLC Device memory Setting area Monitor area System field System field Data field Data field (1) If “0004h” is set for the reading demand flag, the command of reading set value to the setting area will be sent. (3) When completed reading out to the setting area, “0004h” is set for the reading response flag Programless communication module Temperature control module Temperature control module St.1 St.32 (When connected max. units) Setting area field (2) Read out set value to the setting area. Set value Set value Reading data from each temperature control module After reading out, execute the stop operation command demand into the standby status. INP-TN5A0202-E 4-13 to put the programless communication module’s reading 4-17 4.3 Parameter Setting Demand/Response Flag 4.3 Parameter Setting Demand/Response Flag Setting command for the system field “parameter setting demand flag” in the setting area enables the value of the data field to be written to the temperature control module parameter entered as the set parameter. The operation results are set for the “parameter setting response flag” of the system field in the monitor area. Stop operation (Command: 0000h) Setting "0000h" for the system field "parameter setting flag" in the device memory setting area enables the value of data field in the setting area to stop being written to the temperature control module parameter entered as the setting parameter. PLC Device memory Setting area Monitor area System field System field Data field Data field (3) When writing is completed, “0000h” is set for the parameter setting response flag Programless communication module (1) If “0000h” is set for the parameter setting demand flag, stop writing command will be sent. (2) Stop writing set value Temperature control module Temperature control module St.1 St.32 (When connected max. units) Setting area field (2) Stop writing set value Set value Set value The programless communication module comes to be standby for the parameter setting demand with executing this command. Note ● When the parameter setting demand flag is not “0000h” (Stopped state), command for the parameter setting demand flag is not complied. If modify the value of the parameter setting demand flag, set the value after reset the parameter setting demand flag to “0000h”. ● During 1:N connection, each programless communication has a system field and a data field. 4-18 INP-TN5A0202-E 4.3 Parameter Setting Demand/Response Flag Write once (Command: 0001h) Setting "0001h" for the system field "parameter setting flag" in the device memory setting area enables the value of data field in the setting area to be written once to the temperature control module parameter entered as the setting parameter. PLC Device memory Setting area Monitor area System field System field Data field Data field (3) When completed writing, “0001h” is set for the parameter setting response flag Programless communication module (1) If “0001h” is set for the parameter setting demand flag, the writing command will be sent once. Temperature control module Temperature control module St.1 St.32 (When connected max. units) Setting area field Write set values to each temperature control module (2) Writing set value to the temperature control module once. Set value After writing, execute the stop operation command setting demand into the standby status. 4-18 Set value to put the programless communication module’s parameter Note ● The temperature control module judge whether the set value has changed, and only if has changed, the set value will be updated. ● The parameters of the temperature control module that be reset automatically after executing the command, such as the temperature control module’s auto tuning parameters, are not reflected in the memory of PLC. Confirm by the reading demand command INP-TN5A0202-E 4-14 , if the command has be executed. 4-19 4.3 Parameter Setting Demand/Response Flag Continuous writing (Command: 0002h) Setting "0002h" for the system field "parameter setting flag" in the device memory setting area enables the value of data field in the setting area to be written periodically to the temperature control module parameter entered as the setting parameter.(Refer to "PLC communication inter-cycle time" 5-14 about the periodical time). PLC Device memory Setting area Monitor area System field System field Data field Data field (3) If completed the writing, “0002h” will be set to the parameter setting response flag. Programless communication module (1) If “0002h” is set for the parameter setting demand flag, the writing command will be set continuously Temperature control module Temperature control module St.1 St.32 (When connected max. units) Setting area field Write set value to each temperature control module (2) Write set value to the temperature control module continuously Set value Execute the stop operation command order to stop continuous reading out. 4-20 4-18 Set value and put the programless communication module to the standby state in INP-TN5A0202-E 4.4 Command Setting Demand/Response Flag 4.4 Command Setting Demand/Response Flag Setting command for the system field “command setting demand flag” in the setting area enables to indicate the operation for the programless communication module. The operation results are set in the system field “command setting response flag” of the monitor area. Programless communication module status showed by the command setting response flags Command setting response flag Programless communication module status 0000h Standby status: Command can be complied with. EEEEh Standby status: In the standby status after restoration from the programless communication fault. 5-4 FFFFh Restoring status: In the normal status after executing the restoring demand. Other than those above Abnormal status other than the programless communication: Device memory setting duplication, destroying the response value overwritten by the PLC sequence program. INP-TN5A0202-E 4-21 4.4 Command Setting Demand/Response Flag Stop operation (Command: 0000h) Command setting demand status is cleared for the programless communication module by setting “0000h” for the “command setting demand flag”. PLC Device memory Setting area Monitor area System field System field Data field Data field (2) “0000h” is set for the command setting response flag and showed the command setting demand flag is in the complying with demand state. Programless communication module (1) If “0000h” is set for the command setting demand flag, the command setting demand will be cleared. Temperature control module Temperature control module St.1 St.32 (When connected max. units) Executing this command puts the programless communication module into the standby status for the command setting demand. Note ● When the command setting demand flag is not set to “0000h” (Stop operation), the command for the command setting demand flag is not complied with. Set the value after reset the command setting demand flag to “0000h” (Stop operation) to modify the value of the command setting demand flag. ● During 1:N connection, each programless communication has a system field and a data field. 4-22 INP-TN5A0202-E 4.4 Command Setting Demand/Response Flag Communication restoration demand (Command: FFFFh) When “Stop” is selected for the operation select with the “Operation setting when a programless communication fault occurs” 5-4 , this command requests the programless communication module that stops operation with some faults to restart operation. Note To execute the restoration procedure, that "EEEEh"(Stopped status) has been set to the PLC setting area command setting and the stop operation command of 4-13 has sent the normal response is required. response flag and the stop operation command of the reading demand flag the parameter setting demand flag 4-18 PLC (1) After restoration from the line fault, “EEEEh” will be set to the command setting response flag. Device memory Setting area Monitor area System field System field Data field Data field (3) After restoration of the communication, if “FFFFh” is set to the command setting demand flag, “FFFFh” will be set to the command setting response flag. (5) After start communication, “0000h” will be set to the command setting response flag. Programless communication module (2) “FFFFh” is set for the command setting demand flag, the programless communication behavior of the programless communication module restarts. Temperature control module Temperature control module St.1 St.32 (When connected max. units) (4) The communication starts by changing the command setting demand flag from “FFFFh” to “0000h”. After communication restoration, execute the stop operation command module’s command setting demand into the standby status. INP-TN5A0202-E 4-22 to put the programless communication 4-23 4.5 Command Execution Example 4.5 Command Execution Example The example of monitoring PV values of the control module (PUMA/B) connected to the programless communication module and manipulating SV values is shown below. The PLC should use the data registers of No.1000 to 1004 for the setting area, and those of No.0000 to 0004 for the monitor area. In addition, the station number of the control module operated should be “1”, and the operating channel number should be “Ch.1”. Memory setting Set parameters referring to the following table. Parameter MODBUS register No. (Relative address) Set value Setting area device type 40011 (000Ah) 00A8h (Data register) Setting area start address (Lower) 40012 (000Bh) 1000 Setting area start address (Upper) 40013 (000Ch) 0 Setting area device size 40014 (000Dh) 1 Setting area entry St. No. (The 1st word) 41001 (03E8h) 1 Setting area entry register No.(The 1st word) 41002 (03E9h) 41100 (Ch.1 communication SV value) Monitor area device type 40015 (000Eh) 00A8h (Data register) Monitor area start address (Lower) 40016 (000Fh) 0 Monitor area start address (Upper) 40017 (0010h) 0 Monitor area device size 40018 (0011h) 1 Monitor area entry St. No. (The 1st word) 43001 (0BB8h) 1 Monitor area entry register No. (The 1st word) 43002 (0BB9h) 30002 (Ch.1 PV value) 4-24 INP-TN5A0202-E 4.5 Command Execution Example PLC device memory is used as below. D1000 Reading demand flag D1001 D1003 D1004 Data field INP-TN5A0202-E Parameter setting demand flag D0001 Command setting demand flag D0002 System area 1 (Reserved) D0003 Ch.1 SV value for St. No.1 D0004 Reading response flag Monitor area Setting area D1002 System field (Each 1 word) D0000 System field (Each 1 word) Parameter setting response flag Command setting response flag System area 1 (Reserved) Data field Ch.1 PV value for St. No.1 4-25 4.5 Command Execution Example Reading out parameters When “0001h” is set to the reading demand flag (No. D1000), “Control module (St. No.1)’s PV value” is read out to the data filed (No. D0004) in the monitor field, and “0001h” is set to the reading response flag “No. D0000”. PLC Device memory Setting area D1000 Monitor area D0000 Reading demand flag 0001h Reading response flag 0001h D1001 Parameter setting demand flag 0000h D0001 Parameter setting response flag 0000h D1002 Command setting demand flag 0000h D1003 D1004 D0002 D0003 System area 1 0000h Ch1 SV value 0 (0.0°C) (1) Indicate reading out once “Ch1 PV value” by setting “0001h” to the reading demand flag D0004 Command setting response flag 0000h System area 1 0000h Ch1 PV value 1000 (100.0°C) (100.0 (3) If completed reading out properly, “0001h” will be set to the reading response flag. Ch1 PV input 100.0°C Programless communication module Temperature control module St.1 Register contents (2) Reading the monitor value “Ch1 PV value” to the data field in the monitor area once. Content Value Ch1 PV value 100.0°C Ch1 SV value 200.0°C After reading out, set “0000h” (Stop operation)” to the reading demand flag (No. D1000) to put the programless communication module’s reading demand into the standby status. When the reading demand comes to be in the standby, “0000h” will be set to the reading response flag (No. D0000). 4-26 INP-TN5A0202-E 4.5 Command Execution Example Reading out set values to the monitor area When “0003h” is set to the reading demand flag (No. D1000), “Control module (St. No. 1)’s Ch. 1 SV value” is read to the data field in the monitor area, and “0003h” is set to the reading response flag (No. D0000). PLC Device memory Setting area D1000 Monitor area D0000 0003h Reading response flag 0003h D1001 Parameter setting demand flag 0000h D0001 Parameter setting response flag 0000h D1002 Command setting demand flag 0000h D1003 D1004 Reading demand flag D0002 D0003 System area 1 0000h Ch1 SV value 0 (0.0°C) (1) Indicate reading “Ch1 SV value” by setting “0003h” to the reading demand flag. D0004 Command setting response flag 0000h System area 1 0000h Ch1 SV value 2000 (200.0°C) (3) If completed reading out, “0003h” will be set to the reading response flag. Ch1 PV input 100.0°C Programless communication module Temperature control module St.1 Register contents Content Value Ch1 PV value 100.0°C Ch1 SV value 200.0°C (2) Read out entered set value (Ch.1 SV value) in the setting area data field to the monitor area data field. After reading out, set “0000h” (Stop operation) to the reading demand flag (No. D1000) to put the programless communication module’s reading demand into the standby status. When the reading demand comes to be in the standby, “0000h” is set to the reading response flag (No. D0000). INP-TN5A0202-E 4-27 4.5 Command Execution Example Reading out set values to the setting area When “0004h” is set to the reading demand flag (No. D1000), “Control module (St. No. 1)’s Ch. 1 SV value” is read out to the data field in the setting area, and “0004h” is set to the reading response flag (No. D0000). PLC Device memory Setting area D1000 Monitor area D0000 Reading demand flag 0004h Reading response flag 0004h D1001 Parameter setting demand flag 0000h D0001 Parameter setting response flag 0000h D1002 Command setting demand flag 0000h D1003 D1004 D0002 D0003 System area 1 0000h Ch1 SV value 2000 (200.0°C) (1) Indicate reading out “Ch1 SV value” by setting “0004h” to the reading demand flag. D0004 Command setting response flag 0000h System area 1 0000h Ch1 PV value 0 (0°C) (3) If completed reading out, “0004h” will be set to the reading response flag. Ch1 PV input 100.0°C Programless communication module Temperature control module St.1 Register contents Content Value Ch1 PV value 100.0°C Ch1 SV value 200.0°C (2) Reading the set value “Ch1 SV value” to the data field in the setting area. After reading out, set “0000h” (Stop operation) to the reading demand flag (No. D1000) to put the programless communication module’s reading demand into the standby status. When the reading demand comes to be in the standby, “0000h” is set to the reading response flag (No. D0000). 4-28 INP-TN5A0202-E 4.5 Command Execution Example Writing set values When “0001h” is set to the parameter setting demand flag (No. D1001), the value of the data field in the setting area (No.D1004) is written to “Control module (St. No. 1)’s Ch. 1 SV value”, and “0001h” is set to the parameter setting response flag (No. D0001). PLC Device memory Setting area D1000 Monitor area D0000 Reading demand flag 0000h Reading response flag D1001 Parameter setting demand flag 0001h D0001 Parameter setting response flag D1002 Command setting demand flag 0000h D1003 D1004 D0002 D0003 System area 1 0000h Ch1 SV value 1500 (150.0°C) (1) Indicate writing “Ch1 SV value” by setting “0001h” to the parameter setting demand flag. D0004 (3) If completed writing, “0001h” will be set to the parameter setting response flag. - 0001h Command setting response flag - System area 1 - Ch1 PV value 1000 (100.0°C) Ch1 PV input 100.0°C Programless communication module Temperature control module St.1 Register contents Content Value Ch1 PV value 100.0°C Ch1 SV value 150.0°C (2) Write the set value “Ch1 SV value” to the register of the target temperature control module. After writing, set “0000h” (Stop operation) to the parameter setting demand flag (No. D1001) to put the programless communication module’s parameter setting demand into the standby status. When the parameter setting demand comes to be in the standby, “0000h” is set to the parameter setting response flag (No. D0001). INP-TN5A0202-E 4-29 4.5 Command Execution Example 4-30 INP-TN5A0202-E 1 Overview System Configuration 3 Installation 5.1 Programless Communication Module Operation Setting ………………………… 5-3 Memory Setting …………………………… 5-5 5.3 PLC Communication Setting …………… 5-11 5.4 Status Display……………………………… 5-18 5.5 Address Map and Data Format ………… 5-21 5.6 Setting/Monitor Area Entry Numbers 4 Programless Communication Operation 5.2 (Control module) ………………………… 5-51 5.7 Setting/Monitor Area Entry Numbers (Event I/O module) ………………………… 5-64 5 System Configuration 5.8 2 System Configuration Example 5 Setting/Monitor Area Entry Numbers (Analog module)…………………………… 5-71 6 Loader Communications 7 Trouble Shooting INP-TN5A0202-E 5-1 5.1 Programless Communication Module Operation Setting 5-2 INP-TN5A0202-E 5.1 Programless Communication Module Operation Setting 5.1 Programless Communication Module Operation Setting Explanation here is for performing programless communications with a programless communication module. Programless communication module station number configuration switch Setting a station number of a programless communication module. Apply a fine tip flat-head screwdriver to turn the station number configuration switch. PWR PUM-C BUS LOADER STATION 345 F012 E BCD E 7 8 9A BCD 345 6 TX2 7 8 9A RX2 STATION 6 TX1 F012 RX1 Setting range 1:1 connection = 0 (fixed) 1:N connection = 0 to 7 (factory-set value = 0) Note ● When performs programless communication with 1:1 connection, make sure to set "0" to the station number of this equipment. Otherwise, this equipment can not perform communication with PLC. ● When performs programless communication with 1:N connection, make sure to set station numbers of this equipment in order, from "0". If there are missing numbers with the station numbers, this equipment can not perform communication normally with PLC. INP-TN5A0202-E 5-3 5.1 Programless Communication Module Operation Setting Operation setting when a programless communication fault occurs The parameter below sets the operation when a programless communication fault occurs. Refer to the parameters below. Parameter Setting Range Unit Factory-set value Attribute MODBUS Register No. (Relative Address) Operation selection when a programless communication fault occurs 0000h: RUN 0001h: STOP None 0001h R/W 40010 (0009h) When set “0000h (RUN) to “Operation selection when a programless communication fault occurs”, if the communication between PLC and a programless communication module is restored to be in a normal state, the programless communication will recover automatically and the same operation as it did is continued. When set “0001h (STOP)” to “Operation selection when a programless communication fault occurs”, even if the communication between a PLC and a programless communication module is restored to be in a normal state, the programless communication will be in a stopped state. In order to restart a programless communication, use Communication restoration demand. 4-23 5-4 INP-TN5A0202-E 5.2 Memory Setting 5.2 Memory Setting Providing a programless communication area in the PLC device memory for a programless communication is necessary. Memory area The memory area for a programless communication consists of the “setting area” and the “monitor area”. Setting area – Controlling a programless communication – Setting the write value to a module type temperature controller Monitor area – Displaying a programless communication status – Storing the read value from a module type temperature controller Setting area definition Define the PLC memory type and the area used as the “setting area” Refer to the parameters below. Parameter Setting Range Unit Factory-set value Attribute MODBUS register No.(Relative Address) Setting area device type 00A8h: Data register (D) 00B4h: Link register (W) 00AFh: File register (R) 00B0h: File register [for sequence number accessing] (ZR) None 00A8h R/W 40011 (000Ah) Setting area start address (Lower) According to PLC setting None 1000 R/W 40012 (000Bh) Setting area start address (Upper) According to PLC setting None 0 R/W 40013 (000Ch) Setting area device size 0 to 712 Word 0 R/W 40014 (000Dh) Note With 1:N connection, prevent setting area of each programless communication module from being duplication by setting the setting area start address. If setting areas are duplicate, it does not operate normally. INP-TN5A0202-E 5-5 5.2 Memory Setting Communication parameter entry (Setting area) Register the module type temperature controller parameter writing from a PLC with a combination of “Setting area entry St. No.” parameter and the “Setting area entry register No.” parameter with a programless communication. Refer to the parameters below. Parameter Setting Range Unit Factory-set value Attribute MODBUS register No.(Relative Address) Setting area entry St. No. The 1st word 0: Not used 1 to 16: Control/Analog module 17 to 32: Event module None 0 R/W 41001 (03E8h) Setting area entry register No. The 1st word 0,40000 to 49999 (*) None 0 R/W 41002 (03E9h) . . . Setting area entry St. No. The 712th word 0: Not used 1 to 16: Control/Analog module 17 to 32: Event module None 0 R/W 42423 (0976h) Setting area entry register No. The 712th word 0,40000 to 49999 (*) None 0 R/W 42424 (0977h) * Only the address written in “Setting/Monitor area register number” (Control module 5-64 , Analog module 5-71 5-51 , Event module ) settable. However, the monitor parameters and parameter marked “*” in the “Entry ban” column cannot be set. Note Number of registerable parameters per reference station is limited. Also, please note that maximum number of registerable parameters is depends on each module shown below. Modeule Type Maximum No. Control module 32 Analog I/O module 32 Event I/O module 8 If register parameters more than the maximum number, the PWR indicator will blink red (0.4-sec inter-cycle), and then comes to be in the communication fault status. 5-6 INP-TN5A0202-E 5.2 Memory Setting Setting area definition example For example, when “Setting area device type” parameter is “00A8h (data register)”, “Setting area start address” parameter is “1000”, and “Setting area device size” parameter is “712”, setting area is as follows. “Setting area” field Defined by “Setting area device type” or “Setting area start address” D1000 Reading demand flag D1001 D1002 System field (1 word each) D1003 Parameter setting demand flag Command setting demand flag System area 1 (Reserved) D1004 Data field According to the setting parameters' registeration (0 to 712) Defined by “Setting area device size” D1715 Note ● Check the specifications of the PLC used, when setting each parameter of the “Setting area device type”, the “Setting area start address” and the “Setting area device size”. ● If the reserved area is needed, set “0” to the “Setting area entry St. No.” parameter, and “0” to the “Setting area entry register No.” parameter. ● Even if setting each parameter of the “Setting area entry St. No.” parameter and “Setting area entry register No.” parameter beyond the size set by “Setting area device size”. Non-registerable parameter to the Setting area Even if the parameter is within the entry setting range of the “Setting area entry St. No.” or the “Setting area entry register No.”, the monitor parameters and parameter marked “*” in the “Entry ban” column of the “Setting/Monitor area register No.” (Control module 5-51 , Event module 5-64 , Analog module 5-71 cannot be set. Do not set such parameters, since they cannot be modify via programless communications. INP-TN5A0202-E 5-7 5.2 Memory Setting Monitor area definition Define the PLC memory type and the field used as the “monitor area”. Refer to the parameters below. Parameter Monitor area device type Setting Range 00A8h: 00B4h: 00AFh: 00B0h: Data register (D) Link register (W) File register (R) File register [for sequence number accessing] (ZR) Unit Factory-set value Attribute MODBUS register No. (Relative Address) None 00A8h R/W 40015 (000Eh) Monitor area start address (Lower) According to PLC setting None 0 R/W 40016 (000Fh) Monitor area start address (Upper) According to PLC setting None 0 R/W 40017 (0010h) Monitor area device size 0 to 712 Word 0 R/W 40018 (0011h) Note With 1:N connection, prevent monitor area of each programless communication module from being duplication by setting the monitor area start address. If monitor areas are duplicate, it does not operate normally. 5-8 INP-TN5A0202-E 5.2 Memory Setting Communication parameter entry (Monitor area) Register a module type temperature controller parameter reading out from PLC with a programless communication as the combination of the “Monitor area entry St. No.” parameter and the “Monitor area entry register No.” parameter. Refer to the parameters below. Parameter Setting Range 0 1 to 16 Monitor area entry St. No. The 1st word Monitor area entry register No. The 1st word 17 to 32 128 : Not used : Control/Analog module : Event module : Programless communication module 0,30000 to 49999 (*) Unit Factory-set value Attribute MODBUS register No. (Relative Address) None 0 R/W 43001 (0BB8h) None 0 R/W 43002 (0BB9h) None 0 R/W 44423 (1146h) None 0 R/W 44424 (1147h) . . . 0 1 to 16 Monitor area entry St. No. The 712th word Monitor area entry register No. The 712th word * 17 to 32 128 : Not used : Control/Analog module : Event module : Programless communication module 0,30000 to 49999 (*) Only the address written in the “Setting/Monitor area register No.” (Control module Analog module 5-71 5-51 , Event module 5-64 , ) is settable. However, the parameter marked “*” in the “Entry ban” column cannot be set. Note Number of registerable parameters per reference station is limited. Also, please note that maximum number of registerable parameters is depends on each module shown below. Modeule Type Maximum No. Control module 32 Analog I/O module 32 Event I/O module 8 Programless communication module No limit If register parameters more than the maximum number, the PWR indicator will blink red (0.4-sec inter-cycle), and then comes to be in the communication fault status. INP-TN5A0202-E 5-9 5.2 Memory Setting Monitor area definition example For example, if the “Monitor area device type” parameter is “00A8h (data register)”, the “Monitor area start address” parameter is “0”, or the “Monitor area device size” parameter is “712”, the monitor area is as follows. “Monitor area” field Define according to the “Monitor area device type” or the “Monitor area start address” D0000 Reading response flag D0001 D0002 System field (1 word each) D0003 Parameter setting response flag Command setting response flag System area 1 (Reserved) D0004 Data field According to the setting parameters' registeration (0 to 712) Define according to “Monitor area device size” D0715 Note ● Check specifications of the PLC used, when setting each parameter of the “Monitor area device type”, “Monitor area start address”, or “Monitor area device size”. ● When the reserved area is necessary, set “0” to the “Monitor area entry St. No.” parameter or “0” to the “Monitor area entry register No.” ● If each parameter of the “Monitor area entry St. No.” or the “Monitor area entry register No.” is set beyond the size set by the “Monitor area device size” parameter. Non-registerable parameter to the Monitor area Even if the parameter is within the entry setting range of the “Monitor area entry St. No.” or the “Monitor area entry register No.”, the parameter marked “*” in the “Entry ban” column of the “Setting/Monitor area register No.” (Control module Event module 5-64 , Analog module 5-71 5-51 , cannot be set. Do not set such parameters, since they cannot be modify via programless communications. 5-10 INP-TN5A0202-E 5.3 PLC Communication Setting 5.3 PLC Communication Setting Setting for a communication between a programless communication module and the PLC. PLC communication speed setting Setting for the communication speed for a communication between a programless communication module and the PLC. Refer to the parameters below. Parameter Setting Range PLC communication speed 0005h : 9.6kbps 0007h : 19.2kbps 0009h : 38.4kbps 000Ah : 57.6kbps 000Bh : 115.2kbps 000Ch : 230.4kbps Unit Factory-set value Attribute MODBUS register No. (Relative address) None 000Bh R/W 40001 (0000h) Note ● Do not set the set value other than the above ● With MELSEC-Q series, when using a several-unit configuration by 2 or more input points of a communication unit, set a total communication speed set value of each unit's configuration to be within the maximum limit of communication speed of your communication unit. Programless communication module CPU unit Communication unit MELSEC-Q series Communication speed setting 57.6kbps㧗57.6kbps Communication speed setting 57.6kbps Programless communication module Communication speed setting 57.6kbps ● Refer to your PLC's instruction manual for the settable communication speed. ● When using 1:N connection, PLC communication setting of every connected programless communication modules should be the same. INP-TN5A0202-E 5-11 5.3 PLC Communication Setting PLC transmission setting Setting for a communication data bit composition between a programless communication module and a PLC. Refer to the parameter below. Parameter Setting Range Unit Factory-set value Attribute MODBUS register No. (Relative Address) PLC transmission setting 0000h to 001Eh None 000Eh R/W 40002 (0001h) Specify the data bit composition of the communication data referring to the table below. Bit position Contents Bit OFF 0 Bit ON OFF (Fixed) 1 Data bit 2 Parity bit None Have 3 Odd/Even parity Odd Even 4 Stop bit 1 2 5 to 15 ON: 8 bits (Fixed) OFF (Fixed) For example, when desired content is “the data bit is 8 bits, with a parity bit, a even parity use, and the stop bit is “1””, the bit information should be set to “0000 0000 0000 1110b”, and the set value should be set to “000Eh”. Note When using 1:N connection, PLC communication setting of every connected programless communication modules should be the same. 5-12 INP-TN5A0202-E 5.3 PLC Communication Setting MC protocol setting Setting for the protocol type between a programless communication module and a PLC. Refer to the parameter below. Parameter Setting Range Unit Factory-set value Attribute MODBUS register No. (Relative Address) MC protocol 2: Type 2 4: Type 4 5: Type 5 None 5 R/W 40003 (0002h) Note ● Do not set other than "2, 4, 5". ● When using 1:N connection, the settings of every connected programless communication modules should be the same. ● Usable MC protocol is depends on your PLC. Confirm it by your PLC's instruction manual. MC protocol frame types are also different depending on selected MC protocol. Refer to "MC protocol frame types" parameter INP-TN5A0202-E 5-17 for details. 5-13 5.3 PLC Communication Setting Setting for PLC communication starting time Setting for the waiting time until starting programless communications to the PLC after turning the programless communication module’s power on. Refer to the parameters below. Parameter Setting Range Unit Factory-set value Attribute MODBUS register No. (Relative Address) PLC communication starting time 1 to 255 Sec. 1 R/W 40005 (0004h) Note ● After turning the programless communication module’s power on, it takes about 5 to 30 seconds to start communications. If setting the time less than that the programless communication module needs to start communication to the “PLC communication starting time” parameter, the communication with the PLC does not be started within the starting communication time. (Required time to start communication after turning the power on is according to number of the module type temperature controllers connected to the programless communication module.) ● When connecting a module temperature control system with the maximum configuration, it takes about 30 seconds until PLC starts a communication. ● During 1:N connection, until the module which St. No. is "0" starts a communication with PLC, other modules which St. Nos. are not "0" are in the standby state. PLC communication inter-cycle setting Setting the communication inter-cycle between the programless communication module and the PLC Refer to the parameters below. Parameter Setting Range Unit Factory-set value Attribute MODBUS register No. (Relative Address) PLC communication inter-cycle time 0 to 5000 ms 100 R/W 40004 (0003h) Reading out from the PLC setting area and updating of the monitor area is executed at the inter-cycle set here. Point ● Actual time taken for a communication can be confirmed by the “Inter-PLC communication execution time monitor” parameter. 5-19 If the communication has not been performing within the value of the “PLC communication inter-cycle time” parameter, number of the over times is stored in the “PLC communication inter-cycle time overtime counter” parameter. ● When using 1:N connection, the settings of every connected programless communication modules should be the same. 5-14 INP-TN5A0202-E 5.3 PLC Communication Setting PLC communication fault detection setting Setting the retry operation when no programless communication module response from the PLC. Refer to the parameters below. Parameter Setting Range Unit Factory-set value Attribute MODBUS register No. (Relative Address) PLC response monitoring time 10 to 10000 (Unit: 10msec.) ms 200 R/W 40006 (0005h) Number of retry times 0 to 10 times 0 R/W 40007 (0006h) In the case the response from the PLC does not end even the time set by the “PLC response monitoring time” parameter has passed, it retries the times set for the “Number of retry times” parameter. Programless communication module PLC Sending frame Sending frame Responding frame PLC communication fault detecting time Even if no response after retry set for the “The number of retry times” parameter, the operation set for the “Operation setting when a programless communication fault occurs” parameter 5-4 is executed. Note ● “PLC response monitoring time” is judged in units of 10ms. (The fraction less than units of 1ms are rounded off) ● When using 1:N connection, the settings of every connected programless communication modules should be the same INP-TN5A0202-E 5-15 5.3 PLC Communication Setting Connection method Setting the connection method between a PLC and a programless communication module. Refer to the parameters below. Parameter Setting Range Unit Factory-set value Attribute MODBUS register No. (Relative Address) Connection method 0 = 1:1 connection 1 = 1:N connection None 0 R/W 40008 (0007h) Note When using 1:N connection, the settings of every connected programless communication modules should be the same. Number of connected units Setting the number of connected units of PLC and programless communication modules. Refer to the parameters below. Parameter Setting Range Unit Factory-set value Attribute MODBUS register No. (Relative Address) No. of connected units 1 to 8 Unit 1 R/W 40009 (0008h) When selected "1:N connection", set the No. of units for "N". When selected "1:1 connection", set "1". Note ● When using 1:1 connection, ensure to set "1". If the number other than "1" is set, it does not operate normally. ● When using 1:N connection, the settings of every connected programless communication modules should be the same. 5-16 INP-TN5A0202-E 5.3 PLC Communication Setting MC protocol frame types Setting the frame depending on the type selected by MC protocol. Refer to the parameters below. Parameter Setting Range Unit Factory-set value Attribute MODBUS register No. (Relative Address) MC protocol frame types 0: QnA compatible 4C frame 1: A compatible 1C frame None 0 R/W 40019 (0012h) Communicatable combination of MC protocol and MC protocol frame type is as below. Communication object QnA compatible 4C fram RS-232C Q series A series A compatible 1C frame I/F Type 5 Type 2 Type 4 c c c RS-422 ¯ RS-485 ¯ RS-232C ¯ RS-422 ¯ ¯ RS-485 ¯ c RS-232C ¯ ¯ c RS-485 ¯ ¯ c c c c FX series : 1:1 connection + 1:N connection is available c : 1:1 connection is available ¯ : Any connections are not available Note When using 1:N connection, the settings of every connected programless communication modules should be the same. INP-TN5A0202-E 5-17 5.4 Status Display 5.4 Status Display The status display is the parameter in order to monitor the programless communication module operation. The status display is confirmed by reading out from the front face loader port or registering to the PLC monitor area. (Set the “Monitor area entry St. No.” parameter to “128” when entry for the monitor area.) Communication module status The programless communication module operation status can be referred. Refer to the parameters below. Parameter Unit Attribute MODBUS register No. (Relative Address) Setting error None R 30232 (00E7h) Parameters’ explanation – Parameter setting error When the parameter read out from the EEPROM is the invalid value, the error code is stored. Error code Explanation 0101h St. No. configuration SW is invalid value 0102h DIP SW is invalid value 0201h PLC communication speed is invalid value 0202h PLC transmission setting is invalid value 0203h MC protocol is invalid value 0204h PLC communication inter-cycle is invalid value 0205h PLC communication starting time is invalid value 0206h PLC response monitoring time is invalid value 0207h Number of PLC communication retry is invalid value 0208h Connection method is invalid value (Not used) 0209h Number of connected units is invalid value (Not used) 020Ah Operation at PLC communication fault is invalid value 020Ch MC protocol frame type is invalid value 0210h Setting area device type is invalid value 0211h Setting area device size is invalid value 0212h Monitor area device type is invalid value 5-18 INP-TN5A0202-E 5.4 Status Display Error code Explanation 0213h Monitor area device size is invalid value 0214h Setting area detail (The 1st word) is invalid value 0215h Monitor area detail (The 1st word) is invalid value Programless communication status The communication status between the programless communication module and the PLC can be confirmed. Refer to the parameters below. Parameter Unit Attribute MODBUS register No. (Relative Address) PLC error counter time R 31001 (03E8h) PLC error code None R 31002 (03E9h) PLC sending counter time R 31003 (03EAh) PLC receiving counter time R 31004 (03EBh) Inter-PLC communication execution time monitor msec. R 31007 (03EEh) PLC inter-cycle time over counter time R 31008 (03EFh) Each parameter explanation – PLC error counter This is the programless communication error counter. It is added “1”-by-“1” on “0” till “65535”, and then back to “0”. – PLC error code The error codes below are stored. Error code Explanation 0000h to 0042h Error code of A compatible 1C frame 0100h Command message timeout 0101h Response message timeout 0102h Sum check code error 0103h Header format error 0104h ASCII code error 0110h Hardware failure 1 0111h Hardware failure 2 0120h Continuous reception error 7000h to 7FFFh QJ71C24N error code INP-TN5A0202-E 5-19 5.4 Status Display – PLC sending counter This is the programless communication sending counter. It is added “1”-by-“1” on “0” till 65535, and then back to “0”. – PLC receiving counter This is the programless communication receiving counter. It is added “1”-by-“1” on “0” till 65535, and then back to “0”. – Inter-PLC communication execution time monitor The present value of the inter-PLC communication execution time. It is stored per 1ms. The value of inter-PLC communication execution time monitor changes depending on the state of a reading demand flag, a parameter setting demand flag, or a command setting demand flag. – PLC inter-cycle time over counter The number of times that the 1-cycle programless communication within the time set to “PLC communication inter-cycle setting” did not end is displayed. 5-20 INP-TN5A0202-E 5.5 Address Map and Data Format 5.5 Address Map and Data Format Programless communication module status Contents Reading out/Writing data setting range Setting fault 0101h: St. No. configuration SW is invalid value 0102h: DIP SW is invalid value 0201h: PLC communication speed is invalid value 0202h: PLC communication data length is invalid value 0203h: MC protocol is invalid value 0204h: PLC communication inter-cycle is invalid value 0205h: PLC communication starting time is invalid value 0206h: PLC response monitoring time is invalid value 0207h: Number of PLC communication retry is invalid value 0208h: Connection method is invalid value 0209h: Number of connected units is invalid value 020Ah: Operation at PLC communication fault is invalid value 020Ch: MC protocol frame type is invalid value 0210h: Setting area device type is invalid value 0211h: Setting area device size is invalid value 0212h: Monitor area device type is invalid value 0213h: Monitor area device size is invalid value 0214h: Setting area detail (The 1st word) is invalid value 0215h; Monitor area detail (The 1st word) is invalid value Factory-set value - Register No. 30232 Communication status with PLC Contents Reading out/Writing data setting range PLC error counter PLC error code 0→1→…→65535→0→1→…times 0000h to 0042h:Error code of A compatible 1C frame 0100h: Command message timeout 0101h: Response message timeout 0102h: Sum check code error 0103h: Header format error 0104h: ASCII code error 0110h: Hardware failure 1 0111h: Hardware failure 2 0120h: Continuous reception error 7000h to 7FFFh: QJ71C24N error code 0→1→…→65535→0→1→…times 0→1→…→65535→0→1→…times 0 to 65535 ms PLC sending counter PLC receiving counter Inter-PLC communication execution time monitor PLC inter-cycle time over counter 0→1→…→65535→0→1→…times INP-TN5A0202-E Factory-set value - Register No. 31001 31002 - 31003 31004 31007 - 31008 5-21 5.5 Address Map and Data Format PLC communication setting Contents Reading out/Writing data setting range PLC communication speed 0005h: 9600bps 0007h: 19200bps 0009h: 38400bps 000Ah: 57600bps 000Bh: 115200bps 000Ch: 230400bps b0: OFF (fixed) b1: Data bit (ON: 8bits (fixed)) b2: Parity bit (OFF: No, ON: Yes) b3: Odd/Even parity (OFF: Odd ON: Even) b4: Stop bit (OFF: 1, ON: 2) b5 to b15: OFF (fixed) 2: Type 2 4: Type 4 5: Type 5 0 to 5000ms PLC transmission setting MC protocol PLC communication inter-cycle time PLC communication starting time 1 to 255sec PLC response monitoring time 10 to 10000ms Number of retry times 0 to 10 times Factory-set value 000Bh Register No. 40001 000Eh 40002 5 40003 100 40004 1 200 0 40005 40006 40007 Programless communication module operation setting Contents Reading out/Writing data setting range Operation selection at 0000h: RUN programless communication fault 0001h: STOP 5-22 Factory-set value 0001h Register No. 40010 INP-TN5A0202-E 5.5 Address Map and Data Format Memory configuration (Setting area) Contents Reading out/Writing data setting range Factory-set value 00A8h Register No. 1000 40012 Addressable range: according to PLC setting 0 to 712 0 : Not used 1 to 16 : Control/Analog module 17 to 32 : Event module 0,40000 to 49999 (Note1) 0 0 0 40013 40014 41001 0 41002 0 : Not used 1 to 16 : Control/Analog module 17 to 32 : Event module 0,40000 to 49999 (Note1) 0 41003 0 41004 0 42421 0 42422 0 42423 0 42424 Setting area device type 00A8h: Data register (D) 00B4h: Link register (W) 00AFn: File register (R) 00B0h: File register [for sequence No. access](ZR) Setting area start address (lower) Addressable range: according to PLC setting Setting area start address (upper) Setting area device size Setting area entry St. No. (The 1st word) Setting area entry register No. (The 1st word) Setting area entry St. No. (The 2nd word) Setting area entry register No. (The 2nd word) Setting area entry St. No. (The 711th word) Setting area entry register No. (The 711th word) Setting area entry St. No. (The 712th word) Setting area entry register No. (The 712th word) . . . 0 : Not used 1 to 16 : Control/Analog module 17 to 32 : Event module 0,40000 to 49999 (Note1) 0 : Not used 1 to 16 : Control/Analog module 17 to 32 : Event module 0,40000 to 49999 (Note1) Note 1: Only the address written in “Setting/Monitor area register number” (Control module 5-64 40011 , Analog module 5-71 5-51 , Event module ) settable. However, the monitor parameters and parameter marked “*” in the “Entry ban” column cannot be set. INP-TN5A0202-E 5-23 5.5 Address Map and Data Format Memory configuration (Monitor area) Contents Reading out/Writing data setting range Monitor area device type 00A8h: Data register (D) 00B4h: Link register (W) 00AFn: File register (R) 00B0h: File register [for sequence No. access] (ZR) Monitor area start address (lower) Addressable range: according to PLC setting Monitor area start address (upper) Monitor area device size Monitor area entry St. No. (The 1st word) Monitor area entry register No. (The 1st word) Monitor area entry St. No. (The 2nd word) Monitor area entry register No. (The 2nd word) Monitor area entry St. No. (The 711th word) Monitor area entry register No. (The 711th word) Monitor area entry St. No. (The 712th word) Monitor area entry register No. (The 712th word) Register No. 40015 0 40016 Addressable range: according to PLC setting 0 to 712 0 : Not used 1 to 16 : Control/Analog module 17 to 32 : Event module 128 : Programless communication module 0,30000 to 49999 (Note2) 0 0 0 40017 40018 43001 0 43002 0 : Not used 1 to 16 : Control/Analog module 17 to 32 : Event module 128 : Programless communication module 0,30000 to 49999 (Note2) 0 43003 0 43004 0 44421 0 44422 0 44423 0 44424 . . . 0 : Not used 1 to 16 : Control/Analog module 17 to 32 : Event module 128 : Programless communication module 0,30000 to 49999 (Note2) 0 : Not used 1 to 16 : Control/Analog module 17 to 32 : Event module 128 : Programless communication module 0,30000 to 49999 (Note2) Note 2: Only the address written in the “Setting/Monitor area register No.” (Control module 5-64 Factory-set value 00A8h , Analog module 5-71 5-51 , Event module ) is settable. However, the parameter marked “*” in the “Entry ban” column cannot be set. 5-24 INP-TN5A0202-E 5.5 Address Map and Data Format Register number order Register No. PLC communication speed 40001 PLC transmission setting 40002 MC protocol 40003 PLC communication inter-cycle time 40004 PLC communication starting time 40005 PLC response monitoring time 40006 Number of retry times 40007 Connection method 40008 No. of connecting units 40009 Operation selection at programless communication fault 40010 Setting area device type 40011 Setting area start address (lower) 40012 Setting area start address (upper) 40013 Setting area device size 40014 Monitor area device type 40015 Monitor area start address (lower) 40016 Monitor area start address (upper) 40017 Monitor area device size 40018 MC protocol frame types 40019 Setting area entry St. No. The 1st word 41001 Setting area entry register No. The 1st word 41002 Setting area entry St. No. The 2nd word 41003 Setting area entry register No. The 2nd word 41004 Setting area entry St. No. The 3rd word 41005 Setting area entry register No. The 3rd word 41006 Setting area entry St. No. The 4th word 41007 Setting area entry register No. The 4th word 41008 Setting area entry St. No. The 5th word 41009 Setting area entry register No. The 5th word 41010 Setting area entry St. No. The 6th word 41011 Setting area entry register No. The 6th word 41012 Setting area entry St. No. The 7th word 41013 Setting area entry register No. The 7th word 41014 Setting area entry St. No. The 8th word 41015 Setting area entry register No. The 8th word 41016 Setting area entry St. No. The 9th word 41017 Setting area entry register No. The 9th word 41018 Setting area entry St. No. The 10th word 41019 Setting area entry register No. The 10th word 41020 Setting area entry St. No. The 11th word 41021 Setting area entry register No. The 11th word 41022 Setting area entry St. No. The 12th word 41023 Setting area entry register No. The 12th word 41024 Setting area entry St. No. The 13th word 41025 Setting area entry register No. The 13th word 41026 Setting area entry St. No. The 14th word 41027 Setting area entry register No. The 14th word 41028 Setting area entry St. No. The 15th word 41029 Setting area entry register No. The 15th word 41030 Setting area entry St. No. The 16th word 41031 Setting area entry register No. The 16th word 41032 Setting area entry St. No. The 17th word 41033 Setting area entry register No. The 17th word 41034 Contents INP-TN5A0202-E Relative address 0000h 0001h 0002h 0003h 0004h 0005h 0006h 0007h 0008h 0009h 000Ah 000Bh 000Ch 000Dh 000Eh 000Fh 0010h 0011h 0012h 03E8h 03E9h 03EAh 03EBh 03ECh 03EDh 03EEh 03EFh 03F0h 03F1h 03F2h 03F3h 03F4h 03F5h 03F6h 03F7h 03F8h 03F9h 03FAh 03FBh 03FCh 03FDh 03FEh 03FFh 0400h 0401h 0402h 0403h 0404h 0405h 0406h 0407h 0408h 0409h Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. The 18th word The 18th word The 19th word The 19th word The 20th word The 20th word The 21st word The 21st word The 22nd word The 22nd word The 23rd word The 23rd word The 24th word The 24th word The 25th word The 25th word The 26th word The 26th word The 27th word The 27th word The 28th word The 28th word The 29th word The 29th word The 30th word The 30th word The 31st word The 31st word The 32nd word The 32nd word The 33rd word The 33rd word The 34th word The 34th word The 35th word The 35th word The 36th word The 36th word The 37th word The 37th word The 38th word The 38th word The 39th word The 39th word The 40th word The 40th word The 41st word The 41st word The 42nd word The 42nd word The 43rd word The 43rd word Register No. 41035 41036 41037 41038 41039 41040 41041 41042 41043 41044 41045 41046 41047 41048 41049 41050 41051 41052 41053 41054 41055 41056 41057 41058 41059 41060 41061 41062 41063 41064 41065 41066 41067 41068 41069 41070 41071 41072 41073 41074 41075 41076 41077 41078 41079 41080 41081 41082 41083 41084 41085 41086 Relative address 040Ah 040Bh 040Ch 040Dh 040Eh 040Fh 0410h 0411h 0412h 0413h 0414h 0415h 0416h 0417h 0418h 0419h 041Ah 041Bh 041Ch 041Dh 041Eh 041Fh 0420h 0421h 0422h 0423h 0424h 0425h 0426h 0427h 0428h 0429h 042Ah 042Bh 042Ch 042Dh 042Eh 042Fh 0430h 0431h 0432h 0433h 0434h 0435h 0436h 0437h 0438h 0439h 043Ah 043Bh 043Ch 043Dh 5-25 5.5 Address Map and Data Format Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. 5-26 The 44th word The 44th word The 45th word The 45th word The 46th word The 46th word The 47th word The 47th word The 48th word The 48th word The 49th word The 49th word The 50th word The 50th word The 51st word The 51st word The 52nd word The 52nd word The 53rd word The 53rd word The 54th word The 54th word The 55th word The 55th word The 56th word The 56th word The 57th word The 57th word The 58th word The 58th word The 59th word The 59th word The 60th word The 60th word The 61st word The 61st word The 62nd word The 62nd word The 63rd word The 63rd word The 64th word The 64th word The 65th word The 65th word The 66th word The 66th word The 67th word The 67th word The 68th word The 68th word The 69th word The 69th word The 70th word The 70th word The 71st word The 71st word Register No. 41087 41088 41089 41090 41091 41092 41093 41094 41095 41096 41097 41098 41099 41100 41101 41102 41103 41104 41105 41106 41107 41108 41109 41110 41111 41112 41113 41114 41115 41116 41117 41118 41119 41120 41121 41122 41123 41124 41125 41126 41127 41128 41129 41130 41131 41132 41133 41134 41135 41136 41137 41138 41139 41140 41141 41142 Relative address 043Eh 043Fh 0440h 0441h 0442h 0443h 0444h 0445h 0446h 0447h 0448h 0449h 044Ah 044Bh 044Ch 044Dh 044Eh 044Fh 0450h 0451h 0452h 0453h 0454h 0455h 0456h 0457h 0458h 0459h 045Ah 045Bh 045Ch 045Dh 045Eh 045Fh 0460h 0461h 0462h 0463h 0464h 0465h 0466h 0467h 0468h 0469h 046Ah 046Bh 046Ch 046Dh 046Eh 046Fh 0470h 0471h 0472h 0473h 0474h 0475h Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. The 72nd word The 72nd word The 73rd word The 73rd word The 74th word The 74th word The 75th word The 75th word The 76th word The 76th word The 77th word The 77th word The 78th word The 78th word The 79th word The 79th word The 80th word The 80th word The 81st word The 81st word The 82nd word The 82nd word The 83rd word The 83rd word The 84th word The 84th word The 85th word The 85th word The 86th word The 86th word The 87th word The 87th word The 88th word The 88th word The 89th word The 89th word The 90th word The 90th word The 91st word The 91st word The 92nd word The 92nd word The 93rd word The 93rd word The 94th word The 94th word The 95th word The 95th word The 96th word The 96th word The 97th word The 97th word The 98th word The 98th word The 99th word The 99th word Register No. 41143 41144 41145 41146 41147 41148 41149 41150 41151 41152 41153 41154 41155 41156 41157 41158 41159 41160 41161 41162 41163 41164 41165 41166 41167 41168 41169 41170 41171 41172 41173 41174 41175 41176 41177 41178 41179 41180 41181 41182 41183 41184 41185 41186 41187 41188 41189 41190 41191 41192 41193 41194 41195 41196 41197 41198 Relative address 0476h 0477h 0478h 0479h 047Ah 047Bh 047Ch 047Dh 047Eh 047Fh 0480h 0481h 0482h 0483h 0484h 0485h 0486h 0487h 0488h 0489h 048Ah 048Bh 048Ch 048Dh 048Eh 048Fh 0490h 0491h 0492h 0493h 0494h 0495h 0496h 0497h 0498h 0499h 049Ah 049Bh 049Ch 049Dh 049Eh 049Fh 04A0h 04A1h 04A2h 04A3h 04A4h 04A5h 04A6h 04A7h 04A8h 04A9h 04AAh 04ABh 04ACh 04ADh INP-TN5A0202-E 5.5 Address Map and Data Format Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. INP-TN5A0202-E The 100th word The 100th word The 101st word The 101st word The 102nd word The 102nd word The 103rd word The 103rd word The 104th word The 104th word The 105th word The 105th word The 106th word The 106th word The 107th word The 107th word The 108th word The 108th word The 109th word The 109th word The 110th word The 110th word The 111th word The 111th word The 112th word The 112th word The 113th word The 113th word The 114th word The 114th word The 115th word The 115th word The 116th word The 116th word The 117th word The 117th word The 118th word The 118th word The 119th word The 119th word The 120th word The 120th word The 121st word The 121st word The 122nd word The 122nd word The 123rd word The 123rd word The 124th word The 124th word The 125th word The 125th word The 126th word The 126th word The 127th word The 127th word Register No. 41199 41200 41201 41202 41203 41204 41205 41206 41207 41208 41209 41210 41211 41212 41213 41214 41215 41216 41217 41218 41219 41220 41221 41222 41223 41224 41225 41226 41227 41228 41229 41230 41231 41232 41233 41234 41235 41236 41237 41238 41239 41240 41241 41242 41243 41244 41245 41246 41247 41248 41249 41250 41251 41252 41253 41254 Relative address 04AEh 04AFh 04B0h 04B1h 04B2h 04B3h 04B4h 04B5h 04B6h 04B7h 04B8h 04B9h 04BAh 04BBh 04BCh 04BDh 04BEh 04BFh 04C0h 04C1h 04C2h 04C3h 04C4h 04C5h 04C6h 04C7h 04C8h 04C9h 04CAh 04CBh 04CCh 04CDh 04CEh 04CFh 04D0h 04D1h 04D2h 04D3h 04D4h 04D5h 04D6h 04D7h 04D8h 04D9h 04DAh 04DBh 04DCh 04DDh 04DEh 04DFh 04E0h 04E1h 04E2h 04E3h 04E4h 04E5h Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. The 128th word The 128th word The 129th word The 129th word The 130th word The 130th word The 131st word The 131st word The 132nd word The 132nd word The 133rd word The 133rd word The 134th word The 134th word The 135th word The 135th word The 136th word The 136th word The 137th word The 137th word The 138th word The 138th word The 139th word The 139th word The 140th word The 140th word The 141st word The 141st word The 142nd word The 142nd word The 143rd word The 143rd word The 144th word The 144th word The 145th word The 145th word The 146th word The 146th word The 147th word The 147th word The 148th word The 148th word The 149th word The 149th word The 150th word The 150th word The 151st word The 151st word The 152nd word The 152nd word The 153rd word The 153rd word The 154th word The 154th word The 155th word The 155th word Register No. 41255 41256 41257 41258 41259 41260 41261 41262 41263 41264 41265 41266 41267 41268 41269 41270 41271 41272 41273 41274 41275 41276 41277 41278 41279 41280 41281 41282 41283 41284 41285 41286 41287 41288 41289 41290 41291 41292 41293 41294 41295 41296 41297 41298 41299 41300 41301 41302 41303 41304 41305 41306 41307 41308 41309 41310 Relative address 04E6h 04E7h 04E8h 04E9h 04EAh 04EBh 04ECh 04EDh 04EEh 04EFh 04F0h 04F1h 04F2h 04F3h 04F4h 04F5h 04F6h 04F7h 04F8h 04F9h 04FAh 04FBh 04FCh 04FDh 04FEh 04FFh 0500h 0501h 0502h 0503h 0504h 0505h 0506h 0507h 0508h 0509h 050Ah 050Bh 050Ch 050Dh 050Eh 050Fh 0510h 0511h 0512h 0513h 0514h 0515h 0516h 0517h 0518h 0519h 051Ah 051Bh 051Ch 051Dh 5-27 5.5 Address Map and Data Format Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. 5-28 The 156th word The 156th word The 157th word The 157th word The 158th word The 158th word The 159th word The 159th word The 160th word The 160th word The 161st word The 161st word The 162nd word The 162nd word The 163rd word The 163rd word The 164th word The 164th word The 165th word The 165th word The 166th word The 166th word The 167th word The 167th word The 168th word The 168th word The 169th word The 169th word The 170th word The 170th word The 171st word The 171st word The 172nd word The 172nd word The 173rd word The 173rd word The 174th word The 174th word The 175th word The 175th word The 176th word The 176th word The 177th word The 177th word The 178th word The 178th word The 179th word The 179th word The 180th word The 180th word The 181st word The 181st word The 182nd word The 182nd word The 183rd word The 183rd word Register No. 41311 41312 41313 41314 41315 41316 41317 41318 41319 41320 41321 41322 41323 41324 41325 41326 41327 41328 41329 41330 41331 41332 41333 41334 41335 41336 41337 41338 41339 41340 41341 41342 41343 41344 41345 41346 41347 41348 41349 41350 41351 41352 41353 41354 41355 41356 41357 41358 41359 41360 41361 41362 41363 41364 41365 41366 Relative address 051Eh 051Fh 0520h 0521h 0522h 0523h 0524h 0525h 0526h 0527h 0528h 0529h 052Ah 052Bh 052Ch 052Dh 052Eh 052Fh 0530h 0531h 0532h 0533h 0534h 0535h 0536h 0537h 0538h 0539h 053Ah 053Bh 053Ch 053Dh 053Eh 053Fh 0540h 0541h 0542h 0543h 0544h 0545h 0546h 0547h 0548h 0549h 054Ah 054Bh 054Ch 054Dh 054Eh 054Fh 0550h 0551h 0552h 0553h 0554h 0555h Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. The 184th word The 184th word The 185th word The 185th word The 186th word The 186th word The 187th word The 187th word The 188th word The 188th word The 189th word The 189th word The 190th word The 190th word The 191st word The 191st word The 192nd word The 192nd word The 193rd word The 193rd word The 194th word The 194th word The 195th word The 195th word The 196th word The 196th word The 197th word The 197th word The 198th word The 198th word The 199th word The 199th word The 200th word The 200th word The 201st word The 201st word The 202nd word The 202nd word The 203rd word The 203rd word The 204th word The 204th word The 205th word The 205th word The 206th word The 206th word The 207th word The 207th word The 208th word The 208th word The 209th word The 209th word The 210th word The 210th word The 211th word The 211th word Register No. 41367 41368 41369 41370 41371 41372 41373 41374 41375 41376 41377 41378 41379 41380 41381 41382 41383 41384 41385 41386 41387 41388 41389 41390 41391 41392 41393 41394 41395 41396 41397 41398 41399 41400 41401 41402 41403 41404 41405 41406 41407 41408 41409 41410 41411 41412 41413 41414 41415 41416 41417 41418 41419 41420 41421 41422 Relative address 0556h 0557h 0558h 0559h 055Ah 055Bh 055Ch 055Dh 055Eh 055Fh 0560h 0561h 0562h 0563h 0564h 0565h 0566h 0567h 0568h 0569h 056Ah 056Bh 056Ch 056Dh 056Eh 056Fh 0570h 0571h 0572h 0573h 0574h 0575h 0576h 0577h 0578h 0579h 057Ah 057Bh 057Ch 057Dh 057Eh 057Fh 0580h 0581h 0582h 0583h 0584h 0585h 0586h 0587h 0588h 0589h 058Ah 058Bh 058Ch 058Dh INP-TN5A0202-E 5.5 Address Map and Data Format Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. INP-TN5A0202-E The 212th word The 212th word The 213th word The 213th word The 214th word The 214th word The 215th word The 215th word The 216th word The 216th word The 217th word The 217th word The 218th word The 218th word The 219th word The 219th word The 220th word The 220th word The 221st word The 221st word The 222nd word The 222nd word The 223rd word The 223rd word The 224th word The 224th word The 225th word The 225th word The 226th word The 226th word The 227th word The 227th word The 228th word The 228th word The 229th word The 229th word The 230th word The 230th word The 231st word The 231st word The 232nd word The 232nd word The 233rd word The 233rd word The 234th word The 234th word The 235th word The 235th word The 236th word The 236th word The 237th word The 237th word The 238th word The 238th word The 239th word The 239th word Register No. 41423 41424 41425 41426 41427 41428 41429 41430 41431 41432 41433 41434 41435 41436 41437 41438 41439 41440 41441 41442 41443 41444 41445 41446 41447 41448 41449 41450 41451 41452 41453 41454 41455 41456 41457 41458 41459 41460 41461 41462 41463 41464 41465 41466 41467 41468 41469 41470 41471 41472 41473 41474 41475 41476 41477 41478 Relative address 058Eh 058Fh 0590h 0591h 0592h 0593h 0594h 0595h 0596h 0597h 0598h 0599h 059Ah 059Bh 059Ch 059Dh 059Eh 059Fh 05A0h 05A1h 05A2h 05A3h 05A4h 05A5h 05A6h 05A7h 05A8h 05A9h 05AAh 05ABh 05ACh 05ADh 05AEh 05AFh 05B0h 05B1h 05B2h 05B3h 05B4h 05B5h 05B6h 05B7h 05B8h 05B9h 05BAh 05BBh 05BCh 05BDh 05BEh 05BFh 05C0h 05C1h 05C2h 05C3h 05C4h 05C5h Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. The 240th word The 240th word The 241st word The 241st word The 242nd word The 242nd word The 243rd word The 243rd word The 244th word The 244th word The 245th word The 245th word The 246th word The 246th word The 247th word The 247th word The 248th word The 248th word The 249th word The 249th word The 250th word The 250th word The 251st word The 251st word The 252nd word The 252nd word The 253rd word The 253rd word The 254th word The 254th word The 255th word The 255th word The 256th word The 256th word The 257th word The 257th word The 258th word The 258th word The 259th word The 259th word The 260th word The 260th word The 261st word The 261st word The 262nd word The 262nd word The 263rd word The 263rd word The 264th word The 264th word The 265th word The 265th word The 266th word The 266th word The 267th word The 267th word Register No. 41479 41480 41481 41482 41483 41484 41485 41486 41487 41488 41489 41490 41491 41492 41493 41494 41495 41496 41497 41498 41499 41500 41501 41502 41503 41504 41505 41506 41507 41508 41509 41510 41511 41512 41513 41514 41515 41516 41517 41518 41519 41520 41521 41522 41523 41524 41525 41526 41527 41528 41529 41530 41531 41532 41533 41534 Relative address 05C6h 05C7h 05C8h 05C9h 05CAh 05CBh 05CCh 05CDh 05CEh 05CFh 05D0h 05D1h 05D2h 05D3h 05D4h 05D5h 05D6h 05D7h 05D8h 05D9h 05DAh 05DBh 05DCh 05DDh 05DEh 05DFh 05E0h 05E1h 05E2h 05E3h 05E4h 05E5h 05E6h 05E7h 05E8h 05E9h 05EAh 05EBh 05ECh 05EDh 05EEh 05EFh 05F0h 05F1h 05F2h 05F3h 05F4h 05F5h 05F6h 05F7h 05F8h 05F9h 05FAh 05FBh 05FCh 05FDh 5-29 5.5 Address Map and Data Format Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. 5-30 The 268th word The 268th word The 269th word The 269th word The 270th word The 270th word The 271st word The 271st word The 272nd word The 272nd word The 273rd word The 273rd word The 274th word The 274th word The 275th word The 275th word The 276th word The 276th word The 277th word The 277th word The 278th word The 278th word The 279th word The 279th word The 280th word The 280th word The 281st word The 281st word The 282nd word The 282nd word The 283rd word The 283rd word The 284th word The 284th word The 285th word The 285th word The 286th word The 286th word The 287th word The 287th word The 288th word The 288th word The 289th word The 289th word The 290th word The 290th word The 291st word The 291st word The 292nd word The 292nd word The 293rd word The 293rd word The 294th word The 294th word The 295th word The 295th word Register No. 41535 41536 41537 41538 41539 41540 41541 41542 41543 41544 41545 41546 41547 41548 41549 41550 41551 41552 41553 41554 41555 41556 41557 41558 41559 41560 41561 41562 41563 41564 41565 41566 41567 41568 41569 41570 41571 41572 41573 41574 41575 41576 41577 41578 41579 41580 41581 41582 41583 41584 41585 41586 41587 41588 41589 41590 Relative address 05FEh 05FFh 0600h 0601h 0602h 0603h 0604h 0605h 0606h 0607h 0608h 0609h 060Ah 060Bh 060Ch 060Dh 060Eh 060Fh 0610h 0611h 0612h 0613h 0614h 0615h 0616h 0617h 0618h 0619h 061Ah 061Bh 061Ch 061Dh 061Eh 061Fh 0620h 0621h 0622h 0623h 0624h 0625h 0626h 0627h 0628h 0629h 062Ah 062Bh 062Ch 062Dh 062Eh 062Fh 0630h 0631h 0632h 0633h 0634h 0635h Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. The 296th word The 296th word The 297th word The 297th word The 298th word The 298th word The 299th word The 299th word The 300th word The 300th word The 301st word The 301st word The 302nd word The 302nd word The 303rd word The 303rd word The 304th word The 304th word The 305th word The 305th word The 306th word The 306th word The 307th word The 307th word The 308th word The 308th word The 309th word The 309th word The 310th word The 310th word The 311th word The 311th word The 312th word The 312th word The 313th word The 313th word The 314th word The 314th word The 315th word The 315th word The 316th word The 316th word The 317th word The 317th word The 318th word The 318th word The 319th word The 319th word The 320th word The 320th word The 321st word The 321st word The 322nd word The 322nd word The 323rd word The 323rd word Register No. 41591 41592 41593 41594 41595 41596 41597 41598 41599 41600 41601 41602 41603 41604 41605 41606 41607 41608 41609 41610 41611 41612 41613 41614 41615 41616 41617 41618 41619 41620 41621 41622 41623 41624 41625 41626 41627 41628 41629 41630 41631 41632 41633 41634 41635 41636 41637 41638 41639 41640 41641 41642 41643 41644 41645 41646 Relative address 0636h 0637h 0638h 0639h 063Ah 063Bh 063Ch 063Dh 063Eh 063Fh 0640h 0641h 0642h 0643h 0644h 0645h 0646h 0647h 0648h 0649h 064Ah 064Bh 064Ch 064Dh 064Eh 064Fh 0650h 0651h 0652h 0653h 0654h 0655h 0656h 0657h 0658h 0659h 065Ah 065Bh 065Ch 065Dh 065Eh 065Fh 0660h 0661h 0662h 0663h 0664h 0665h 0666h 0667h 0668h 0669h 066Ah 066Bh 066Ch 066Dh INP-TN5A0202-E 5.5 Address Map and Data Format Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. INP-TN5A0202-E The 324th word The 324th word The 325th word The 325th word The 326th word The 326th word The 327th word The 327th word The 328th word The 328th word The 329th word The 329th word The 330th word The 330th word The 331st word The 331st word The 332nd word The 332nd word The 333rd word The 333rd word The 334th word The 334th word The 335th word The 335th word The 336th word The 336th word The 337th word The 337th word The 338th word The 338th word The 339th word The 339th word The 340th word The 340th word The 341st word The 341st word The 342nd word The 342nd word The 343rd word The 343rd word The 344th word The 344th word The 345th word The 345th word The 346th word The 346th word The 347th word The 347th word The 348th word The 348th word The 349th word The 349th word The 350th word The 350th word The 351st word The 351st word Register No. 41647 41648 41649 41650 41651 41652 41653 41654 41655 41656 41657 41658 41659 41660 41661 41662 41663 41664 41665 41666 41667 41668 41669 41670 41671 41672 41673 41674 41675 41676 41677 41678 41679 41680 41681 41682 41683 41684 41685 41686 41687 41688 41689 41690 41691 41692 41693 41694 41695 41696 41697 41698 41699 41700 41701 41702 Relative address 066Eh 066Fh 0670h 0671h 0672h 0673h 0674h 0675h 0676h 0677h 0678h 0679h 067Ah 067Bh 067Ch 067Dh 067Eh 067Fh 0680h 0681h 0682h 0683h 0684h 0685h 0686h 0687h 0688h 0689h 068Ah 068Bh 068Ch 068Dh 068Eh 068Fh 0690h 0691h 0692h 0693h 0694h 0695h 0696h 0697h 0698h 0699h 069Ah 069Bh 069Ch 069Dh 069Eh 069Fh 06A0h 06A1h 06A2h 06A3h 06A4h 06A5h Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. The 352nd word The 352nd word The 353rd word The 353rd word The 354th word The 354th word The 355th word The 355th word The 356th word The 356th word The 357th word The 357th word The 358th word The 358th word The 359th word The 359th word The 360th word The 360th word The 361st word The 361st word The 362nd word The 362nd word The 363rd word The 363rd word The 364th word The 364th word The 365th word The 365th word The 366th word The 366th word The 367th word The 367th word The 368th word The 368th word The 369th word The 369th word The 370th word The 370th word The 371st word The 371st word The 372nd word The 372nd word The 373rd word The 373rd word The 374th word The 374th word The 375th word The 375th word The 376th word The 376th word The 377th word The 377th word The 378th word The 378th word The 379th word The 379th word Register No. 41703 41704 41705 41706 41707 41708 41709 41710 41711 41712 41713 41714 41715 41716 41717 41718 41719 41720 41721 41722 41723 41724 41725 41726 41727 41728 41729 41730 41731 41732 41733 41734 41735 41736 41737 41738 41739 41740 41741 41742 41743 41744 41745 41746 41747 41748 41749 41750 41751 41752 41753 41754 41755 41756 41757 41758 Relative address 06A6h 06A7h 06A8h 06A9h 06AAh 06ABh 06ACh 06ADh 06AEh 06AFh 06B0h 06B1h 06B2h 06B3h 06B4h 06B5h 06B6h 06B7h 06B8h 06B9h 06BAh 06BBh 06BCh 06BDh 06BEh 06BFh 06C0h 06C1h 06C2h 06C3h 06C4h 06C5h 06C6h 06C7h 06C8h 06C9h 06CAh 06CBh 06CCh 06CDh 06CEh 06CFh 06D0h 06D1h 06D2h 06D3h 06D4h 06D5h 06D6h 06D7h 06D8h 06D9h 06DAh 06DBh 06DCh 06DDh 5-31 5.5 Address Map and Data Format Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. 5-32 The 380th word The 380th word The 381st word The 381st word The 382nd word The 382nd word The 383rd word The 383rd word The 384th word The 384th word The 385th word The 385th word The 386th word The 386th word The 387th word The 387th word The 388th word The 388th word The 389th word The 389th word The 390th word The 390th word The 391st word The 391st word The 392nd word The 392nd word The 393rd word The 393rd word The 394th word The 394th word The 395th word The 395th word The 396th word The 396th word The 397th word The 397th word The 398th word The 398th word The 399th word The 399th word The 400th word The 400th word The 401st word The 401st word The 402nd word The 402nd word The 403rd word The 403rd word The 404th word The 404th word The 405th word The 405th word The 406th word The 406th word The 407th word The 407th word Register No. 41759 41760 41761 41762 41763 41764 41765 41766 41767 41768 41769 41770 41771 41772 41773 41774 41775 41776 41777 41778 41779 41780 41781 41782 41783 41784 41785 41786 41787 41788 41789 41790 41791 41792 41793 41794 41795 41796 41797 41798 41799 41800 41801 41802 41803 41804 41805 41806 41807 41808 41809 41810 41811 41812 41813 41814 Relative address 06DEh 06DFh 06E0h 06E1h 06E2h 06E3h 06E4h 06E5h 06E6h 06E7h 06E8h 06E9h 06EAh 06EBh 06ECh 06EDh 06EEh 06EFh 06F0h 06F1h 06F2h 06F3h 06F4h 06F5h 06F6h 06F7h 06F8h 06F9h 06FAh 06FBh 06FCh 06FDh 06FEh 06FFh 0700h 0701h 0702h 0703h 0704h 0705h 0706h 0707h 0708h 0709h 070Ah 070Bh 070Ch 070Dh 070Eh 070Fh 0710h 0711h 0712h 0713h 0714h 0715h Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. The 408th word The 408th word The 409th word The 409th word The 410th word The 410th word The 411th word The 411th word The 412th word The 412th word The 413th word The 413th word The 414th word The 414th word The 415th word The 415th word The 416th word The 416th word The 417th word The 417th word The 418th word The 418th word The 419th word The 419th word The 420th word The 420th word The 421st word The 421st word The 422nd word The 422nd word The 423rd word The 423rd word The 424th word The 424th word The 425th word The 425th word The 426th word The 426th word The 427th word The 427th word The 428th word The 428th word The 429th word The 429th word The 430th word The 430th word The 431st word The 431st word The 432nd word The 432nd word The 433rd word The 433rd word The 434th word The 434th word The 435th word The 435th word Register No. 41815 41816 41817 41818 41819 41820 41821 41822 41823 41824 41825 41826 41827 41828 41829 41830 41831 41832 41833 41834 41835 41836 41837 41838 41839 41840 41841 41842 41843 41844 41845 41846 41847 41848 41849 41850 41851 41852 41853 41854 41855 41856 41857 41858 41859 41860 41861 41862 41863 41864 41865 41866 41867 41868 41869 41870 Relative address 0716h 0717h 0718h 0719h 071Ah 071Bh 071Ch 071Dh 071Eh 071Fh 0720h 0721h 0722h 0723h 0724h 0725h 0726h 0727h 0728h 0729h 072Ah 072Bh 072Ch 072Dh 072Eh 072Fh 0730h 0731h 0732h 0733h 0734h 0735h 0736h 0737h 0738h 0739h 073Ah 073Bh 073Ch 073Dh 073Eh 073Fh 0740h 0741h 0742h 0743h 0744h 0745h 0746h 0747h 0748h 0749h 074Ah 074Bh 074Ch 074Dh INP-TN5A0202-E 5.5 Address Map and Data Format Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. INP-TN5A0202-E The 436th word The 436th word The 437th word The 437th word The 438th word The 438th word The 439th word The 439th word The 440th word The 440th word The 441st word The 441st word The 442nd word The 442nd word The 443rd word The 443rd word The 444th word The 444th word The 445th word The 445th word The 446th word The 446th word The 447th word The 447th word The 448th word The 448th word The 449th word The 449th word The 450th word The 450th word The 451st word The 451st word The 452nd word The 452nd word The 453rd word The 453rd word The 454th word The 454th word The 455th word The 455th word The 456th word The 456th word The 457th word The 457th word The 458th word The 458th word The 459th word The 459th word The 460th word The 460th word The 461st word The 461st word The 462nd word The 462nd word The 463rd word The 463rd word Register No. 41871 41872 41873 41874 41875 41876 41877 41878 41879 41880 41881 41882 41883 41884 41885 41886 41887 41888 41889 41890 41891 41892 41893 41894 41895 41896 41897 41898 41899 41900 41901 41902 41903 41904 41905 41906 41907 41908 41909 41910 41911 41912 41913 41914 41915 41916 41917 41918 41919 41920 41921 41922 41923 41924 41925 41926 Relative address 074Eh 074Fh 0750h 0751h 0752h 0753h 0754h 0755h 0756h 0757h 0758h 0759h 075Ah 075Bh 075Ch 075Dh 075Eh 075Fh 0760h 0761h 0762h 0763h 0764h 0765h 0766h 0767h 0768h 0769h 076Ah 076Bh 076Ch 076Dh 076Eh 076Fh 0770h 0771h 0772h 0773h 0774h 0775h 0776h 0777h 0778h 0779h 077Ah 077Bh 077Ch 077Dh 077Eh 077Fh 0780h 0781h 0782h 0783h 0784h 0785h Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. The 464th word The 464th word The 465th word The 465th word The 466th word The 466th word The 467th word The 467th word The 468th word The 468th word The 469th word The 469th word The 470th word The 470th word The 471st word The 471st word The 472nd word The 472nd word The 473rd word The 473rd word The 474th word The 474th word The 475th word The 475th word The 476th word The 476th word The 477th word The 477th word The 478th word The 478th word The 479th word The 479th word The 480th word The 480th word The 481st word The 481st word The 482nd word The 482nd word The 483rd word The 483rd word The 484th word The 484th word The 485th word The 485th word The 486th word The 486th word The 487th word The 487th word The 488th word The 488th word The 489th word The 489th word The 490th word The 490th word The 491st word The 491st word Register No. 41927 41928 41929 41930 41931 41932 41933 41934 41935 41936 41937 41938 41939 41940 41941 41942 41943 41944 41945 41946 41947 41948 41949 41950 41951 41952 41953 41954 41955 41956 41957 41958 41959 41960 41961 41962 41963 41964 41965 41966 41967 41968 41969 41970 41971 41972 41973 41974 41975 41976 41977 41978 41979 41980 41981 41982 Relative address 0786h 0787h 0788h 0789h 078Ah 078Bh 078Ch 078Dh 078Eh 078Fh 0790h 0791h 0792h 0793h 0794h 0795h 0796h 0797h 0798h 0799h 079Ah 079Bh 079Ch 079Dh 079Eh 079Fh 07A0h 07A1h 07A2h 07A3h 07A4h 07A5h 07A6h 07A7h 07A8h 07A9h 07AAh 07ABh 07ACh 07ADh 07AEh 07AFh 07B0h 07B1h 07B2h 07B3h 07B4h 07B5h 07B6h 07B7h 07B8h 07B9h 07BAh 07BBh 07BCh 07BDh 5-33 5.5 Address Map and Data Format Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. 5-34 The 492nd word The 492nd word The 493rd word The 493rd word The 494th word The 494th word The 495th word The 495th word The 496th word The 496th word The 497th word The 497th word The 498th word The 498th word The 499th word The 499th word The 500th word The 500th word The 501st word The 501st word The 502nd word The 502nd word The 503rd word The 503rd word The 504th word The 504th word The 505th word The 505th word The 506th word The 506th word The 507th word The 507th word The 508th word The 508th word The 509th word The 509th word The 510th word The 510th word The 511th word The 511th word The 512th word The 512th word The 513th word The 513th word The 514th word The 514th word The 515th word The 515th word The 516th word The 516th word The 517th word The 517th word The 518th word The 518th word The 519th word The 519th word Register No. 41983 41984 41985 41986 41987 41988 41989 41990 41991 41992 41993 41994 41995 41996 41997 41998 41999 42000 42001 42002 42003 42004 42005 42006 42007 42008 42009 42010 42011 42012 42013 42014 42015 42016 42017 42018 42019 42020 42021 42022 42023 42024 42025 42026 42027 42028 42029 42030 42031 42032 42033 42034 42035 42036 42037 42038 Relative address 07BEh 07BFh 07C0h 07C1h 07C2h 07C3h 07C4h 07C5h 07C6h 07C7h 07C8h 07C9h 07CAh 07CBh 07CCh 07CDh 07CEh 07CFh 07D0h 07D1h 07D2h 07D3h 07D4h 07D5h 07D6h 07D7h 07D8h 07D9h 07DAh 07DBh 07DCh 07DDh 07DEh 07DFh 07E0h 07E1h 07E2h 07E3h 07E4h 07E5h 07E6h 07E7h 07E8h 07E9h 07EAh 07EBh 07ECh 07EDh 07EEh 07EFh 07F0h 07F1h 07F2h 07F3h 07F4h 07F5h Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. The 520th word The 520th word The 521st word The 521st word The 522nd word The 522nd word The 523rd word The 523rd word The 524th word The 524th word The 525th word The 525th word The 526th word The 526th word The 527th word The 527th word The 528th word The 528th word The 529th word The 529th word The 530th word The 530th word The 531st word The 531st word The 532nd word The 532nd word The 533rd word The 533rd word The 534th word The 534th word The 535th word The 535th word The 536th word The 536th word The 537th word The 537th word The 538th word The 538th word The 539th word The 539th word The 540th word The 540th word The 541st word The 541st word The 542nd word The 542nd word The 543rd word The 543rd word The 544th word The 544th word The 545th word The 545th word The 546th word The 546th word The 547th word The 547th word Register No. 42039 42040 42041 42042 42043 42044 42045 42046 42047 42048 42049 42050 42051 42052 42053 42054 42055 42056 42057 42058 42059 42060 42061 42062 42063 42064 42065 42066 42067 42068 42069 42070 42071 42072 42073 42074 42075 42076 42077 42078 42079 42080 42081 42082 42083 42084 42085 42086 42087 42088 42089 42090 42091 42092 42093 42094 Relative address 07F6h 07F7h 07F8h 07F9h 07FAh 07FBh 07FCh 07FDh 07FEh 07FFh 0800h 0801h 0802h 0803h 0804h 0805h 0806h 0807h 0808h 0809h 080Ah 080Bh 080Ch 080Dh 080Eh 080Fh 0810h 0811h 0812h 0813h 0814h 0815h 0816h 0817h 0818h 0819h 081Ah 081Bh 081Ch 081Dh 081Eh 081Fh 0820h 0821h 0822h 0823h 0824h 0825h 0826h 0827h 0828h 0829h 082Ah 082Bh 082Ch 082Dh INP-TN5A0202-E 5.5 Address Map and Data Format Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. INP-TN5A0202-E The 548th word The 548th word The 549th word The 549th word The 550th word The 550th word The 551st word The 551st word The 552nd word The 552nd word The 553rd word The 553rd word The 554th word The 554th word The 555th word The 555th word The 556th word The 556th word The 557th word The 557th word The 558th word The 558th word The 559th word The 559th word The 560th word The 560th word The 561st word The 561st word The 562nd word The 562nd word The 563rd word The 563rd word The 564th word The 564th word The 565th word The 565th word The 566th word The 566th word The 567th word The 567th word The 568th word The 568th word The 569th word The 569th word The 570th word The 570th word The 571st word The 571st word The 572nd word The 572nd word The 573rd word The 573rd word The 574th word The 574th word The 575th word The 575th word Register No. 42095 42096 42097 42098 42099 42100 42101 42102 42103 42104 42105 42106 42107 42108 42109 42110 42111 42112 42113 42114 42115 42116 42117 42118 42119 42120 42121 42122 42123 42124 42125 42126 42127 42128 42129 42130 42131 42132 42133 42134 42135 42136 42137 42138 42139 42140 42141 42142 42143 42144 42145 42146 42147 42148 42149 42150 Relative address 082Eh 082Fh 0830h 0831h 0832h 0833h 0834h 0835h 0836h 0837h 0838h 0839h 083Ah 083Bh 083Ch 083Dh 083Eh 083Fh 0840h 0841h 0842h 0843h 0844h 0845h 0846h 0847h 0848h 0849h 084Ah 084Bh 084Ch 084Dh 084Eh 084Fh 0850h 0851h 0852h 0853h 0854h 0855h 0856h 0857h 0858h 0859h 085Ah 085Bh 085Ch 085Dh 085Eh 085Fh 0860h 0861h 0862h 0863h 0864h 0865h Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. The 576th word The 576th word The 577th word The 577th word The 578th word The 578th word The 579th word The 579th word The 580th word The 580th word The 581st word The 581st word The 582nd word The 582nd word The 583rd word The 583rd word The 584th word The 584th word The 585th word The 585th word The 586th word The 586th word The 587th word The 587th word The 588th word The 588th word The 589th word The 589th word The 590th word The 590th word The 591st word The 591st word The 592nd word The 592nd word The 593rd word The 593rd word The 594th word The 594th word The 595th word The 595th word The 596th word The 596th word The 597th word The 597th word The 598th word The 598th word The 599th word The 599th word The 600th word The 600th word The 601st word The 601st word The 602nd word The 602nd word The 603rd word The 603rd word Register No. 42151 42152 42153 42154 42155 42156 42157 42158 42159 42160 42161 42162 42163 42164 42165 42166 42167 42168 42169 42170 42171 42172 42173 42174 42175 42176 42177 42178 42179 42180 42181 42182 42183 42184 42185 42186 42187 42188 42189 42190 42191 42192 42193 42194 42195 42196 42197 42198 42199 42200 42201 42202 42203 42204 42205 42206 Relative address 0866h 0867h 0868h 0869h 086Ah 086Bh 086Ch 086Dh 086Eh 086Fh 0870h 0871h 0872h 0873h 0874h 0875h 0876h 0877h 0878h 0879h 087Ah 087Bh 087Ch 087Dh 087Eh 087Fh 0880h 0881h 0882h 0883h 0884h 0885h 0886h 0887h 0888h 0889h 088Ah 088Bh 088Ch 088Dh 088Eh 088Fh 0890h 0891h 0892h 0893h 0894h 0895h 0896h 0897h 0898h 0899h 089Ah 089Bh 089Ch 089Dh 5-35 5.5 Address Map and Data Format Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. 5-36 The 604th word The 604th word The 605th word The 605th word The 606th word The 606th word The 607th word The 607th word The 608th word The 608th word The 609th word The 609th word The 610th word The 610th word The 611th word The 611th word The 612th word The 612th word The 613th word The 613th word The 614th word The 614th word The 615th word The 615th word The 616th word The 616th word The 617th word The 617th word The 618th word The 618th word The 619th word The 619th word The 620th word The 620th word The 621st word The 621st word The 622nd word The 622nd word The 623rd word The 623rd word The 624th word The 624th word The 625th word The 625th word The 626th word The 626th word The 627th word The 627th word The 628th word The 628th word The 629th word The 629th word The 630th word The 630th word The 631st word The 631st word Register No. 42207 42208 42209 42210 42211 42212 42213 42214 42215 42216 42217 42218 42219 42220 42221 42222 42223 42224 42225 42226 42227 42228 42229 42230 42231 42232 42233 42234 42235 42236 42237 42238 42239 42240 42241 42242 42243 42244 42245 42246 42247 42248 42249 42250 42251 42252 42253 42254 42255 42256 42257 42258 42259 42260 42261 42262 Relative address 089Eh 089Fh 08A0h 08A1h 08A2h 08A3h 08A4h 08A5h 08A6h 08A7h 08A8h 08A9h 08AAh 08ABh 08ACh 08ADh 08AEh 08AFh 08B0h 08B1h 08B2h 08B3h 08B4h 08B5h 08B6h 08B7h 08B8h 08B9h 08BAh 08BBh 08BCh 08BDh 08BEh 08BFh 08C0h 08C1h 08C2h 08C3h 08C4h 08C5h 08C6h 08C7h 08C8h 08C9h 08CAh 08CBh 08CCh 08CDh 08CEh 08CFh 08D0h 08D1h 08D2h 08D3h 08D4h 08D5h Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. The 632nd word The 632nd word The 633rd word The 633rd word The 634th word The 634th word The 635th word The 635th word The 636th word The 636th word The 637th word The 637th word The 638th word The 638th word The 639th word The 639th word The 640th word The 640th word The 641st word The 641st word The 642nd word The 642nd word The 643rd word The 643rd word The 644th word The 644th word The 645th word The 645th word The 646th word The 646th word The 647th word The 647th word The 648th word The 648th word The 649th word The 649th word The 650th word The 650th word The 651st word The 651st word The 652nd word The 652nd word The 653rd word The 653rd word The 654th word The 654th word The 655th word The 655th word The 656th word The 656th word The 657th word The 657th word The 658th word The 658th word The 659th word The 659th word Register No. 42263 42264 42265 42266 42267 42268 42269 42270 42271 42272 42273 42274 42275 42276 42277 42278 42279 42280 42281 42282 42283 42284 42285 42286 42287 42288 42289 42290 42291 42292 42293 42294 42295 42296 42297 42298 42299 42300 42301 42302 42303 42304 42305 42306 42307 42308 42309 42310 42311 42312 42313 42314 42315 42316 42317 42318 Relative address 08D6h 08D7h 08D8h 08D9h 08DAh 08DBh 08DCh 08DDh 08DEh 08DFh 08E0h 08E1h 08E2h 08E3h 08E4h 08E5h 08E6h 08E7h 08E8h 08E9h 08EAh 08EBh 08ECh 08EDh 08EEh 08EFh 08F0h 08F1h 08F2h 08F3h 08F4h 08F5h 08F6h 08F7h 08F8h 08F9h 08FAh 08FBh 08FCh 08FDh 08FEh 08FFh 0900h 0901h 0902h 0903h 0904h 0905h 0906h 0907h 0908h 0909h 090Ah 090Bh 090Ch 090Dh INP-TN5A0202-E 5.5 Address Map and Data Format Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. INP-TN5A0202-E The 660th word The 660th word The 661st word The 661st word The 662nd word The 662nd word The 663rd word The 663rd word The 664th word The 664th word The 665th word The 665th word The 666th word The 666th word The 667th word The 667th word The 668th word The 668th word The 669th word The 669th word The 670th word The 670th word The 671st word The 671st word The 672nd word The 672nd word The 673rd word The 673rd word The 674th word The 674th word The 675th word The 675th word The 676th word The 676th word The 677th word The 677th word The 678th word The 678th word The 679th word The 679th word The 680th word The 680th word The 681st word The 681st word The 682nd word The 682nd word The 683rd word The 683rd word The 684th word The 684th word The 685th word The 685th word The 686th word The 686th word The 687th word The 687th word Register No. 42319 42320 42321 42322 42323 42324 42325 42326 42327 42328 42329 42330 42331 42332 42333 42334 42335 42336 42337 42338 42339 42340 42341 42342 42343 42344 42345 42346 42347 42348 42349 42350 42351 42352 42353 42354 42355 42356 42357 42358 42359 42360 42361 42362 42363 42364 42365 42366 42367 42368 42369 42370 42371 42372 42373 42374 Relative address 090Eh 090Fh 0910h 0911h 0912h 0913h 0914h 0915h 0916h 0917h 0918h 0919h 091Ah 091Bh 091Ch 091Dh 091Eh 091Fh 0920h 0921h 0922h 0923h 0924h 0925h 0926h 0927h 0928h 0929h 092Ah 092Bh 092Ch 092Dh 092Eh 092Fh 0930h 0931h 0932h 0933h 0934h 0935h 0936h 0937h 0938h 0939h 093Ah 093Bh 093Ch 093Dh 093Eh 093Fh 0940h 0941h 0942h 0943h 0944h 0945h Contents Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Setting area entry St. No. Setting area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. The 688th word The 688th word The 689th word The 689th word The 690th word The 690th word The 691st word The 691st word The 692nd word The 692nd word The 693rd word The 693rd word The 694th word The 694th word The 695th word The 695th word The 696th word The 696th word The 697th word The 697th word The 698th word The 698th word The 699th word The 699th word The 700th word The 700th word The 701st word The 701st word The 702nd word The 702nd word The 703rd word The 703rd word The 704th word The 704th word The 705th word The 705th word The 706th word The 706th word The 707th word The 707th word The 708th word The 708th word The 709th word The 709th word The 710th word The 710th word The 711th word The 711th word The 712th word The 712th word The 1st word The 1st word The 2nd word The 2nd word The 3rd word The 3rd word Register No. 42375 42376 42377 42378 42379 42380 42381 42382 42383 42384 42385 42386 42387 42388 42389 42390 42391 42392 42393 42394 42395 42396 42397 42398 42399 42400 42401 42402 42403 42404 42405 42406 42407 42408 42409 42410 42411 42412 42413 42414 42415 42416 42417 42418 42419 42420 42421 42422 42423 42424 43001 43002 43003 43004 43005 43006 Relative address 0946h 0947h 0948h 0949h 094Ah 094Bh 094Ch 094Dh 094Eh 094Fh 0950h 0951h 0952h 0953h 0954h 0955h 0956h 0957h 0958h 0959h 095Ah 095Bh 095Ch 095Dh 095Eh 095Fh 0960h 0961h 0962h 0963h 0964h 0965h 0966h 0967h 0968h 0969h 096Ah 096Bh 096Ch 096Dh 096Eh 096Fh 0970h 0971h 0972h 0973h 0974h 0975h 0976h 0977h 0BB8h 0BB9h 0BBAh 0BBBh 0BBCh 0BBDh 5-37 5.5 Address Map and Data Format Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. 5-38 The 4th word The 4th word The 5th word The 5th word The 6th word The 6th word The 7th word The 7th word The 8th word The 8th word The 9th word The 9th word The 10th word The 10th word The 11th word The 11th word The 12th word The 12th word The 13th word The 13th word The 14th word The 14th word The 15th word The 15th word The 16th word The 16th word The 17th word The 17th word The 18th word The 18th word The 19th word The 19th word The 20th word The 20th word The 21st word The 21st word The 22nd word The 22nd word The 23rd word The 23rd word The 24th word The 24th word The 25th word The 25th word The 26th word The 26th word The 27th word The 27th word The 28th word The 28th word The 29th word The 29th word The 30th word The 30th word The 31st word The 31st word Register No. 43007 43008 43009 43010 43011 43012 43013 43014 43015 43016 43017 43018 43019 43020 43021 43022 43023 43024 43025 43026 43027 43028 43029 43030 43031 43032 43033 43034 43035 43036 43037 43038 43039 43040 43041 43042 43043 43044 43045 43046 43047 43048 43049 43050 43051 43052 43053 43054 43055 43056 43057 43058 43059 43060 43061 43062 Relative address 0BBEh 0BBFh 0BC0h 0BC1h 0BC2h 0BC3h 0BC4h 0BC5h 0BC6h 0BC7h 0BC8h 0BC9h 0BCAh 0BCBh 0BCCh 0BCDh 0BCEh 0BCFh 0BD0h 0BD1h 0BD2h 0BD3h 0BD4h 0BD5h 0BD6h 0BD7h 0BD8h 0BD9h 0BDAh 0BDBh 0BDCh 0BDDh 0BDEh 0BDFh 0BE0h 0BE1h 0BE2h 0BE3h 0BE4h 0BE5h 0BE6h 0BE7h 0BE8h 0BE9h 0BEAh 0BEBh 0BECh 0BEDh 0BEEh 0BEFh 0BF0h 0BF1h 0BF2h 0BF3h 0BF4h 0BF5h Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. The 32nd word The 32nd word The 33rd word The 33rd word The 34th word The 34th word The 35th word The 35th word The 36th word The 36th word The 37th word The 37th word The 38th word The 38th word The 39th word The 39th word The 40th word The 40th word The 41st word The 41st word The 42nd word The 42nd word The 43rd word The 43rd word The 44th word The 44th word The 45th word The 45th word The 46th word The 46th word The 47th word The 47th word The 48th word The 48th word The 49th word The 49th word The 50th word The 50th word The 51st word The 51st word The 52nd word The 52nd word The 53rd word The 53rd word The 54th word The 54th word The 55th word The 55th word The 56th word The 56th word The 57th word The 57th word The 58th word The 58th word The 59th word The 59th word Register No. 43063 43064 43065 43066 43067 43068 43069 43070 43071 43072 43073 43074 43075 43076 43077 43078 43079 43080 43081 43082 43083 43084 43085 43086 43087 43088 43089 43090 43091 43092 43093 43094 43095 43096 43097 43098 43099 43100 43101 43102 43103 43104 43105 43106 43107 43108 43109 43110 43111 43112 43113 43114 43115 43116 43117 43118 Relative address 0BF6h 0BF7h 0BF8h 0BF9h 0BFAh 0BFBh 0BFCh 0BFDh 0BFEh 0BFFh 0C00h 0C01h 0C02h 0C03h 0C04h 0C05h 0C06h 0C07h 0C08h 0C09h 0C0Ah 0C0Bh 0C0Ch 0C0Dh 0C0Eh 0C0Fh 0C10h 0C11h 0C12h 0C13h 0C14h 0C15h 0C16h 0C17h 0C18h 0C19h 0C1Ah 0C1Bh 0C1Ch 0C1Dh 0C1Eh 0C1Fh 0C20h 0C21h 0C22h 0C23h 0C24h 0C25h 0C26h 0C27h 0C28h 0C29h 0C2Ah 0C2Bh 0C2Ch 0C2Dh INP-TN5A0202-E 5.5 Address Map and Data Format Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. INP-TN5A0202-E The 60th word The 60th word The 61st word The 61st word The 62nd word The 62nd word The 63rd word The 63rd word The 64th word The 64th word The 65th word The 65th word The 66th word The 66th word The 67th word The 67th word The 68th word The 68th word The 69th word The 69th word The 70th word The 70th word The 71st word The 71st word The 72nd word The 72nd word The 73rd word The 73rd word The 74th word The 74th word The 75th word The 75th word The 76th word The 76th word The 77th word The 77th word The 78th word The 78th word The 79th word The 79th word The 80th word The 80th word The 81st word The 81st word The 82nd word The 82nd word The 83rd word The 83rd word The 84th word The 84th word The 85th word The 85th word The 86th word The 86th word The 87th word The 87th word Register No. 43119 43120 43121 43122 43123 43124 43125 43126 43127 43128 43129 43130 43131 43132 43133 43134 43135 43136 43137 43138 43139 43140 43141 43142 43143 43144 43145 43146 43147 43148 43149 43150 43151 43152 43153 43154 43155 43156 43157 43158 43159 43160 43161 43162 43163 43164 43165 43166 43167 43168 43169 43170 43171 43172 43173 43174 Relative address 0C2Eh 0C2Fh 0C30h 0C31h 0C32h 0C33h 0C34h 0C35h 0C36h 0C37h 0C38h 0C39h 0C3Ah 0C3Bh 0C3Ch 0C3Dh 0C3Eh 0C3Fh 0C40h 0C41h 0C42h 0C43h 0C44h 0C45h 0C46h 0C47h 0C48h 0C49h 0C4Ah 0C4Bh 0C4Ch 0C4Dh 0C4Eh 0C4Fh 0C50h 0C51h 0C52h 0C53h 0C54h 0C55h 0C56h 0C57h 0C58h 0C59h 0C5Ah 0C5Bh 0C5Ch 0C5Dh 0C5Eh 0C5Fh 0C60h 0C61h 0C62h 0C63h 0C64h 0C65h Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. The 88th word The 88th word The 89th word The 89th word The 90th word The 90th word The 91st word The 91st word The 92nd word The 92nd word The 93rd word The 93rd word The 94th word The 94th word The 95th word The 95th word The 96th word The 96th word The 97th word The 97th word The 98th word The 98th word The 99th word The 99th word The 100th word The 100th word The 101st word The 101st word The 102nd word The 102nd word The 103rd word The 103rd word The 104th word The 104th word The 105th word The 105th word The 106th word The 106th word The 107th word The 107th word The 108th word The 108th word The 109th word The 109th word The 110th word The 110th word The 111th word The 111th word The 112th word The 112th word The 113th word The 113th word The 114th word The 114th word The 115th word The 115th word Register No. 43175 43176 43177 43178 43179 43180 43181 43182 43183 43184 43185 43186 43187 43188 43189 43190 43191 43192 43193 43194 43195 43196 43197 43198 43199 43200 43201 43202 43203 43204 43205 43206 43207 43208 43209 43210 43211 43212 43213 43214 43215 43216 43217 43218 43219 43220 43221 43222 43223 43224 43225 43226 43227 43228 43229 43230 Relative address 0C66h 0C67h 0C68h 0C69h 0C6Ah 0C6Bh 0C6Ch 0C6Dh 0C6Eh 0C6Fh 0C70h 0C71h 0C72h 0C73h 0C74h 0C75h 0C76h 0C77h 0C78h 0C79h 0C7Ah 0C7Bh 0C7Ch 0C7Dh 0C7Eh 0C7Fh 0C80h 0C81h 0C82h 0C83h 0C84h 0C85h 0C86h 0C87h 0C88h 0C89h 0C8Ah 0C8Bh 0C8Ch 0C8Dh 0C8Eh 0C8Fh 0C90h 0C91h 0C92h 0C93h 0C94h 0C95h 0C96h 0C97h 0C98h 0C99h 0C9Ah 0C9Bh 0C9Ch 0C9Dh 5-39 5.5 Address Map and Data Format Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. 5-40 The 116th word The 116th word The 117th word The 117th word The 118th word The 118th word The 119th word The 119th word The 120th word The 120th word The 121st word The 121st word The 122nd word The 122nd word The 123rd word The 123rd word The 124th word The 124th word The 125th word The 125th word The 126th word The 126th word The 127th word The 127th word The 128th word The 128th word The 129th word The 129th word The 130th word The 130th word The 131st word The 131st word The 132nd word The 132nd word The 133rd word The 133rd word The 134th word The 134th word The 135th word The 135th word The 136th word The 136th word The 137th word The 137th word The 138th word The 138th word The 139th word The 139th word The 140th word The 140th word The 141st word The 141st word The 142nd word The 142nd word The 143rd word The 143rd word Register No. 43231 43232 43233 43234 43235 43236 43237 43238 43239 43240 43241 43242 43243 43244 43245 43246 43247 43248 43249 43250 43251 43252 43253 43254 43255 43256 43257 43258 43259 43260 43261 43262 43263 43264 43265 43266 43267 43268 43269 43270 43271 43272 43273 43274 43275 43276 43277 43278 43279 43280 43281 43282 43283 43284 43285 43286 Relative address 0C9Eh 0C9Fh 0CA0h 0CA1h 0CA2h 0CA3h 0CA4h 0CA5h 0CA6h 0CA7h 0CA8h 0CA9h 0CAAh 0CABh 0CACh 0CADh 0CAEh 0CAFh 0CB0h 0CB1h 0CB2h 0CB3h 0CB4h 0CB5h 0CB6h 0CB7h 0CB8h 0CB9h 0CBAh 0CBBh 0CBCh 0CBDh 0CBEh 0CBFh 0CC0h 0CC1h 0CC2h 0CC3h 0CC4h 0CC5h 0CC6h 0CC7h 0CC8h 0CC9h 0CCAh 0CCBh 0CCCh 0CCDh 0CCEh 0CCFh 0CD0h 0CD1h 0CD2h 0CD3h 0CD4h 0CD5h Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. The 144th word The 144th word The 145th word The 145th word The 146th word The 146th word The 147th word The 147th word The 148th word The 148th word The 149th word The 149th word The 150th word The 150th word The 151st word The 151st word The 152nd word The 152nd word The 153rd word The 153rd word The 154th word The 154th word The 155th word The 155th word The 156th word The 156th word The 157th word The 157th word The 158th word The 158th word The 159th word The 159th word The 160th word The 160th word The 161st word The 161st word The 162nd word The 162nd word The 163rd word The 163rd word The 164th word The 164th word The 165th word The 165th word The 166th word The 166th word The 167th word The 167th word The 168th word The 168th word The 169th word The 169th word The 170th word The 170th word The 171st word The 171st word Register No. 43287 43288 43289 43290 43291 43292 43293 43294 43295 43296 43297 43298 43299 43300 43301 43302 43303 43304 43305 43306 43307 43308 43309 43310 43311 43312 43313 43314 43315 43316 43317 43318 43319 43320 43321 43322 43323 43324 43325 43326 43327 43328 43329 43330 43331 43332 43333 43334 43335 43336 43337 43338 43339 43340 43341 43342 Relative address 0CD6h 0CD7h 0CD8h 0CD9h 0CDAh 0CDBh 0CDCh 0CDDh 0CDEh 0CDFh 0CE0h 0CE1h 0CE2h 0CE3h 0CE4h 0CE5h 0CE6h 0CE7h 0CE8h 0CE9h 0CEAh 0CEBh 0CECh 0CEDh 0CEEh 0CEFh 0CF0h 0CF1h 0CF2h 0CF3h 0CF4h 0CF5h 0CF6h 0CF7h 0CF8h 0CF9h 0CFAh 0CFBh 0CFCh 0CFDh 0CFEh 0CFFh 0D00h 0D01h 0D02h 0D03h 0D04h 0D05h 0D06h 0D07h 0D08h 0D09h 0D0Ah 0D0Bh 0D0Ch 0D0Dh INP-TN5A0202-E 5.5 Address Map and Data Format Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. INP-TN5A0202-E The 172nd word The 172nd word The 173rd word The 173rd word The 174th word The 174th word The 175th word The 175th word The 176th word The 176th word The 177th word The 177th word The 178th word The 178th word The 179th word The 179th word The 180th word The 180th word The 181st word The 181st word The 182nd word The 182nd word The 183rd word The 183rd word The 184th word The 184th word The 185th word The 185th word The 186th word The 186th word The 187th word The 187th word The 188th word The 188th word The 189th word The 189th word The 190th word The 190th word The 191st word The 191st word The 192nd word The 192nd word The 193rd word The 193rd word The 194th word The 194th word The 195th word The 195th word The 196th word The 196th word The 197th word The 197th word The 198th word The 198th word The 199th word The 199th word Register No. 43343 43344 43345 43346 43347 43348 43349 43350 43351 43352 43353 43354 43355 43356 43357 43358 43359 43360 43361 43362 43363 43364 43365 43366 43367 43368 43369 43370 43371 43372 43373 43374 43375 43376 43377 43378 43379 43380 43381 43382 43383 43384 43385 43386 43387 43388 43389 43390 43391 43392 43393 43394 43395 43396 43397 43398 Relative address 0D0Eh 0D0Fh 0D10h 0D11h 0D12h 0D13h 0D14h 0D15h 0D16h 0D17h 0D18h 0D19h 0D1Ah 0D1Bh 0D1Ch 0D1Dh 0D1Eh 0D1Fh 0D20h 0D21h 0D22h 0D23h 0D24h 0D25h 0D26h 0D27h 0D28h 0D29h 0D2Ah 0D2Bh 0D2Ch 0D2Dh 0D2Eh 0D2Fh 0D30h 0D31h 0D32h 0D33h 0D34h 0D35h 0D36h 0D37h 0D38h 0D39h 0D3Ah 0D3Bh 0D3Ch 0D3Dh 0D3Eh 0D3Fh 0D40h 0D41h 0D42h 0D43h 0D44h 0D45h Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. The 200th word The 200th word The 201st word The 201st word The 202nd word The 202nd word The 203rd word The 203rd word The 204th word The 204th word The 205th word The 205th word The 206th word The 206th word The 207th word The 207th word The 208th word The 208th word The 209th word The 209th word The 210th word The 210th word The 211th word The 211th word The 212th word The 212th word The 213th word The 213th word The 214th word The 214th word The 215th word The 215th word The 216th word The 216th word The 217th word The 217th word The 218th word The 218th word The 219th word The 219th word The 220th word The 220th word The 221st word The 221st word The 222nd word The 222nd word The 223rd word The 223rd word The 224th word The 224th word The 225th word The 225th word The 226th word The 226th word The 227th word The 227th word Register No. 43399 43400 43401 43402 43403 43404 43405 43406 43407 43408 43409 43410 43411 43412 43413 43414 43415 43416 43417 43418 43419 43420 43421 43422 43423 43424 43425 43426 43427 43428 43429 43430 43431 43432 43433 43434 43435 43436 43437 43438 43439 43440 43441 43442 43443 43444 43445 43446 43447 43448 43449 43450 43451 43452 43453 43454 Relative address 0D46h 0D47h 0D48h 0D49h 0D4Ah 0D4Bh 0D4Ch 0D4Dh 0D4Eh 0D4Fh 0D50h 0D51h 0D52h 0D53h 0D54h 0D55h 0D56h 0D57h 0D58h 0D59h 0D5Ah 0D5Bh 0D5Ch 0D5Dh 0D5Eh 0D5Fh 0D60h 0D61h 0D62h 0D63h 0D64h 0D65h 0D66h 0D67h 0D68h 0D69h 0D6Ah 0D6Bh 0D6Ch 0D6Dh 0D6Eh 0D6Fh 0D70h 0D71h 0D72h 0D73h 0D74h 0D75h 0D76h 0D77h 0D78h 0D79h 0D7Ah 0D7Bh 0D7Ch 0D7Dh 5-41 5.5 Address Map and Data Format Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. 5-42 The 228th word The 228th word The 229th word The 229th word The 230th word The 230th word The 231st word The 231st word The 232nd word The 232nd word The 233rd word The 233rd word The 234th word The 234th word The 235th word The 235th word The 236th word The 236th word The 237th word The 237th word The 238th word The 238th word The 239th word The 239th word The 240th word The 240th word The 241st word The 241st word The 242nd word The 242nd word The 243rd word The 243rd word The 244th word The 244th word The 245th word The 245th word The 246th word The 246th word The 247th word The 247th word The 248th word The 248th word The 249th word The 249th word The 250th word The 250th word The 251st word The 251st word The 252nd word The 252nd word The 253rd word The 253rd word The 254th word The 254th word The 255th word The 255th word Register No. 43455 43456 43457 43458 43459 43460 43461 43462 43463 43464 43465 43466 43467 43468 43469 43470 43471 43472 43473 43474 43475 43476 43477 43478 43479 43480 43481 43482 43483 43484 43485 43486 43487 43488 43489 43490 43491 43492 43493 43494 43495 43496 43497 43498 43499 43500 43501 43502 43503 43504 43505 43506 43507 43508 43509 43510 Relative address 0D7Eh 0D7Fh 0D80h 0D81h 0D82h 0D83h 0D84h 0D85h 0D86h 0D87h 0D88h 0D89h 0D8Ah 0D8Bh 0D8Ch 0D8Dh 0D8Eh 0D8Fh 0D90h 0D91h 0D92h 0D93h 0D94h 0D95h 0D96h 0D97h 0D98h 0D99h 0D9Ah 0D9Bh 0D9Ch 0D9Dh 0D9Eh 0D9Fh 0DA0h 0DA1h 0DA2h 0DA3h 0DA4h 0DA5h 0DA6h 0DA7h 0DA8h 0DA9h 0DAAh 0DABh 0DACh 0DADh 0DAEh 0DAFh 0DB0h 0DB1h 0DB2h 0DB3h 0DB4h 0DB5h Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. The 256th word The 256th word The 257th word The 257th word The 258th word The 258th word The 259th word The 259th word The 260th word The 260th word The 261st word The 261st word The 262nd word The 262nd word The 263rd word The 263rd word The 264th word The 264th word The 265th word The 265th word The 266th word The 266th word The 267th word The 267th word The 268th word The 268th word The 269th word The 269th word The 270th word The 270th word The 271st word The 271st word The 272nd word The 272nd word The 273rd word The 273rd word The 274th word The 274th word The 275th word The 275th word The 276th word The 276th word The 277th word The 277th word The 278th word The 278th word The 279th word The 279th word The 280th word The 280th word The 281st word The 281st word The 282nd word The 282nd word The 283rd word The 283rd word Register No. 43511 43512 43513 43514 43515 43516 43517 43518 43519 43520 43521 43522 43523 43524 43525 43526 43527 43528 43529 43530 43531 43532 43533 43534 43535 43536 43537 43538 43539 43540 43541 43542 43543 43544 43545 43546 43547 43548 43549 43550 43551 43552 43553 43554 43555 43556 43557 43558 43559 43560 43561 43562 43563 43564 43565 43566 Relative address 0DB6h 0DB7h 0DB8h 0DB9h 0DBAh 0DBBh 0DBCh 0DBDh 0DBEh 0DBFh 0DC0h 0DC1h 0DC2h 0DC3h 0DC4h 0DC5h 0DC6h 0DC7h 0DC8h 0DC9h 0DCAh 0DCBh 0DCCh 0DCDh 0DCEh 0DCFh 0DD0h 0DD1h 0DD2h 0DD3h 0DD4h 0DD5h 0DD6h 0DD7h 0DD8h 0DD9h 0DDAh 0DDBh 0DDCh 0DDDh 0DDEh 0DDFh 0DE0h 0DE1h 0DE2h 0DE3h 0DE4h 0DE5h 0DE6h 0DE7h 0DE8h 0DE9h 0DEAh 0DEBh 0DECh 0DEDh INP-TN5A0202-E 5.5 Address Map and Data Format Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. INP-TN5A0202-E The 284th word The 284th word The 285th word The 285th word The 286th word The 286th word The 287th word The 287th word The 288th word The 288th word The 289th word The 289th word The 290th word The 290th word The 291st word The 291st word The 292nd word The 292nd word The 293rd word The 293rd word The 294th word The 294th word The 295th word The 295th word The 296th word The 296th word The 297th word The 297th word The 298th word The 298th word The 299th word The 299th word The 300th word The 300th word The 301st word The 301st word The 302nd word The 302nd word The 303rd word The 303rd word The 304th word The 304th word The 305th word The 305th word The 306th word The 306th word The 307th word The 307th word The 308th word The 308th word The 309th word The 309th word The 310th word The 310th word The 311th word The 311th word Register No. 43567 43568 43569 43570 43571 43572 43573 43574 43575 43576 43577 43578 43579 43580 43581 43582 43583 43584 43585 43586 43587 43588 43589 43590 43591 43592 43593 43594 43595 43596 43597 43598 43599 43600 43601 43602 43603 43604 43605 43606 43607 43608 43609 43610 43611 43612 43613 43614 43615 43616 43617 43618 43619 43620 43621 43622 Relative address 0DEEh 0DEFh 0DF0h 0DF1h 0DF2h 0DF3h 0DF4h 0DF5h 0DF6h 0DF7h 0DF8h 0DF9h 0DFAh 0DFBh 0DFCh 0DFDh 0DFEh 0DFFh 0E00h 0E01h 0E02h 0E03h 0E04h 0E05h 0E06h 0E07h 0E08h 0E09h 0E0Ah 0E0Bh 0E0Ch 0E0Dh 0E0Eh 0E0Fh 0E10h 0E11h 0E12h 0E13h 0E14h 0E15h 0E16h 0E17h 0E18h 0E19h 0E1Ah 0E1Bh 0E1Ch 0E1Dh 0E1Eh 0E1Fh 0E20h 0E21h 0E22h 0E23h 0E24h 0E25h Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. The 312th word The 312th word The 313th word The 313th word The 314th word The 314th word The 315th word The 315th word The 316th word The 316th word The 317th word The 317th word The 318th word The 318th word The 319th word The 319th word The 320th word The 320th word The 321st word The 321st word The 322nd word The 322nd word The 323rd word The 323rd word The 324th word The 324th word The 325th word The 325th word The 326th word The 326th word The 327th word The 327th word The 328th word The 328th word The 329th word The 329th word The 330th word The 330th word The 331st word The 331st word The 332nd word The 332nd word The 333rd word The 333rd word The 334th word The 334th word The 335th word The 335th word The 336th word The 336th word The 337th word The 337th word The 338th word The 338th word The 339th word The 339th word Register No. 43623 43624 43625 43626 43627 43628 43629 43630 43631 43632 43633 43634 43635 43636 43637 43638 43639 43640 43641 43642 43643 43644 43645 43646 43647 43648 43649 43650 43651 43652 43653 43654 43655 43656 43657 43658 43659 43660 43661 43662 43663 43664 43665 43666 43667 43668 43669 43670 43671 43672 43673 43674 43675 43676 43677 43678 Relative address 0E26h 0E27h 0E28h 0E29h 0E2Ah 0E2Bh 0E2Ch 0E2Dh 0E2Eh 0E2Fh 0E30h 0E31h 0E32h 0E33h 0E34h 0E35h 0E36h 0E37h 0E38h 0E39h 0E3Ah 0E3Bh 0E3Ch 0E3Dh 0E3Eh 0E3Fh 0E40h 0E41h 0E42h 0E43h 0E44h 0E45h 0E46h 0E47h 0E48h 0E49h 0E4Ah 0E4Bh 0E4Ch 0E4Dh 0E4Eh 0E4Fh 0E50h 0E51h 0E52h 0E53h 0E54h 0E55h 0E56h 0E57h 0E58h 0E59h 0E5Ah 0E5Bh 0E5Ch 0E5Dh 5-43 5.5 Address Map and Data Format Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. 5-44 The 340th word The 340th word The 341st word The 341st word The 342nd word The 342nd word The 343rd word The 343rd word The 344th word The 344th word The 345th word The 345th word The 346th word The 346th word The 347th word The 347th word The 348th word The 348th word The 349th word The 349th word The 350th word The 350th word The 351st word The 351st word The 352nd word The 352nd word The 353rd word The 353rd word The 354th word The 354th word The 355th word The 355th word The 356th word The 356th word The 357th word The 357th word The 358th word The 358th word The 359th word The 359th word The 360th word The 360th word The 361st word The 361st word The 362nd word The 362nd word The 363rd word The 363rd word The 364th word The 364th word The 365th word The 365th word The 366th word The 366th word The 367th word The 367th word Register No. 43679 43680 43681 43682 43683 43684 43685 43686 43687 43688 43689 43690 43691 43692 43693 43694 43695 43696 43697 43698 43699 43700 43701 43702 43703 43704 43705 43706 43707 43708 43709 43710 43711 43712 43713 43714 43715 43716 43717 43718 43719 43720 43721 43722 43723 43724 43725 43726 43727 43728 43729 43730 43731 43732 43733 43734 Relative address 0E5Eh 0E5Fh 0E60h 0E61h 0E62h 0E63h 0E64h 0E65h 0E66h 0E67h 0E68h 0E69h 0E6Ah 0E6Bh 0E6Ch 0E6Dh 0E6Eh 0E6Fh 0E70h 0E71h 0E72h 0E73h 0E74h 0E75h 0E76h 0E77h 0E78h 0E79h 0E7Ah 0E7Bh 0E7Ch 0E7Dh 0E7Eh 0E7Fh 0E80h 0E81h 0E82h 0E83h 0E84h 0E85h 0E86h 0E87h 0E88h 0E89h 0E8Ah 0E8Bh 0E8Ch 0E8Dh 0E8Eh 0E8Fh 0E90h 0E91h 0E92h 0E93h 0E94h 0E95h Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. The 368th word The 368th word The 369th word The 369th word The 370th word The 370th word The 371st word The 371st word The 372nd word The 372nd word The 373rd word The 373rd word The 374th word The 374th word The 375th word The 375th word The 376th word The 376th word The 377th word The 377th word The 378th word The 378th word The 379th word The 379th word The 380th word The 380th word The 381st word The 381st word The 382nd word The 382nd word The 383rd word The 383rd word The 384th word The 384th word The 385th word The 385th word The 386th word The 386th word The 387th word The 387th word The 388th word The 388th word The 389th word The 389th word The 390th word The 390th word The 391st word The 391st word The 392nd word The 392nd word The 393rd word The 393rd word The 394th word The 394th word The 395th word The 395th word Register No. 43735 43736 43737 43738 43739 43740 43741 43742 43743 43744 43745 43746 43747 43748 43749 43750 43751 43752 43753 43754 43755 43756 43757 43758 43759 43760 43761 43762 43763 43764 43765 43766 43767 43768 43769 43770 43771 43772 43773 43774 43775 43776 43777 43778 43779 43780 43781 43782 43783 43784 43785 43786 43787 43788 43789 43790 Relative address 0E96h 0E97h 0E98h 0E99h 0E9Ah 0E9Bh 0E9Ch 0E9Dh 0E9Eh 0E9Fh 0EA0h 0EA1h 0EA2h 0EA3h 0EA4h 0EA5h 0EA6h 0EA7h 0EA8h 0EA9h 0EAAh 0EABh 0EACh 0EADh 0EAEh 0EAFh 0EB0h 0EB1h 0EB2h 0EB3h 0EB4h 0EB5h 0EB6h 0EB7h 0EB8h 0EB9h 0EBAh 0EBBh 0EBCh 0EBDh 0EBEh 0EBFh 0EC0h 0EC1h 0EC2h 0EC3h 0EC4h 0EC5h 0EC6h 0EC7h 0EC8h 0EC9h 0ECAh 0ECBh 0ECCh 0ECDh INP-TN5A0202-E 5.5 Address Map and Data Format Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. INP-TN5A0202-E The 396th word The 396th word The 397th word The 397th word The 398th word The 398th word The 399th word The 399th word The 400th word The 400th word The 401st word The 401st word The 402nd word The 402nd word The 403rd word The 403rd word The 404th word The 404th word The 405th word The 405th word The 406th word The 406th word The 407th word The 407th word The 408th word The 408th word The 409th word The 409th word The 410th word The 410th word The 411th word The 411th word The 412th word The 412th word The 413th word The 413th word The 414th word The 414th word The 415th word The 415th word The 416th word The 416th word The 417th word The 417th word The 418th word The 418th word The 419th word The 419th word The 420th word The 420th word The 421st word The 421st word The 422nd word The 422nd word The 423rd word The 423rd word Register No. 43791 43792 43793 43794 43795 43796 43797 43798 43799 43800 43801 43802 43803 43804 43805 43806 43807 43808 43809 43810 43811 43812 43813 43814 43815 43816 43817 43818 43819 43820 43821 43822 43823 43824 43825 43826 43827 43828 43829 43830 43831 43832 43833 43834 43835 43836 43837 43838 43839 43840 43841 43842 43843 43844 43845 43846 Relative address 0ECEh 0ECFh 0ED0h 0ED1h 0ED2h 0ED3h 0ED4h 0ED5h 0ED6h 0ED7h 0ED8h 0ED9h 0EDAh 0EDBh 0EDCh 0EDDh 0EDEh 0EDFh 0EE0h 0EE1h 0EE2h 0EE3h 0EE4h 0EE5h 0EE6h 0EE7h 0EE8h 0EE9h 0EEAh 0EEBh 0EECh 0EEDh 0EEEh 0EEFh 0EF0h 0EF1h 0EF2h 0EF3h 0EF4h 0EF5h 0EF6h 0EF7h 0EF8h 0EF9h 0EFAh 0EFBh 0EFCh 0EFDh 0EFEh 0EFFh 0F00h 0F01h 0F02h 0F03h 0F04h 0F05h Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. The 424th word The 424th word The 425th word The 425th word The 426th word The 426th word The 427th word The 427th word The 428th word The 428th word The 429th word The 429th word The 430th word The 430th word The 431st word The 431st word The 432nd word The 432nd word The 433rd word The 433rd word The 434th word The 434th word The 435th word The 435th word The 436th word The 436th word The 437th word The 437th word The 438th word The 438th word The 439th word The 439th word The 440th word The 440th word The 441st word The 441st word The 442nd word The 442nd word The 443rd word The 443rd word The 444th word The 444th word The 445th word The 445th word The 446th word The 446th word The 447th word The 447th word The 448th word The 448th word The 449th word The 449th word The 450th word The 450th word The 451st word The 451st word Register No. 43847 43848 43849 43850 43851 43852 43853 43854 43855 43856 43857 43858 43859 43860 43861 43862 43863 43864 43865 43866 43867 43868 43869 43870 43871 43872 43873 43874 43875 43876 43877 43878 43879 43880 43881 43882 43883 43884 43885 43886 43887 43888 43889 43890 43891 43892 43893 43894 43895 43896 43897 43898 43899 43900 43901 43902 Relative address 0F06h 0F07h 0F08h 0F09h 0F0Ah 0F0Bh 0F0Ch 0F0Dh 0F0Eh 0F0Fh 0F10h 0F11h 0F12h 0F13h 0F14h 0F15h 0F16h 0F17h 0F18h 0F19h 0F1Ah 0F1Bh 0F1Ch 0F1Dh 0F1Eh 0F1Fh 0F20h 0F21h 0F22h 0F23h 0F24h 0F25h 0F26h 0F27h 0F28h 0F29h 0F2Ah 0F2Bh 0F2Ch 0F2Dh 0F2Eh 0F2Fh 0F30h 0F31h 0F32h 0F33h 0F34h 0F35h 0F36h 0F37h 0F38h 0F39h 0F3Ah 0F3Bh 0F3Ch 0F3Dh 5-45 5.5 Address Map and Data Format Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. 5-46 The 452nd word The 452nd word The 453rd word The 453rd word The 454th word The 454th word The 455th word The 455th word The 456th word The 456th word The 457th word The 457th word The 458th word The 458th word The 459th word The 459th word The 460th word The 460th word The 461st word The 461st word The 462nd word The 462nd word The 463rd word The 463rd word The 464th word The 464th word The 465th word The 465th word The 466th word The 466th word The 467th word The 467th word The 468th word The 468th word The 469th word The 469th word The 470th word The 470th word The 471st word The 471st word The 472nd word The 472nd word The 473rd word The 473rd word The 474th word The 474th word The 475th word The 475th word The 476th word The 476th word The 477th word The 477th word The 478th word The 478th word The 479th word The 479th word Register No. 43903 43904 43905 43906 43907 43908 43909 43910 43911 43912 43913 43914 43915 43916 43917 43918 43919 43920 43921 43922 43923 43924 43925 43926 43927 43928 43929 43930 43931 43932 43933 43934 43935 43936 43937 43938 43939 43940 43941 43942 43943 43944 43945 43946 43947 43948 43949 43950 43951 43952 43953 43954 43955 43956 43957 43958 Relative address 0F3Eh 0F3Fh 0F40h 0F41h 0F42h 0F43h 0F44h 0F45h 0F46h 0F47h 0F48h 0F49h 0F4Ah 0F4Bh 0F4Ch 0F4Dh 0F4Eh 0F4Fh 0F50h 0F51h 0F52h 0F53h 0F54h 0F55h 0F56h 0F57h 0F58h 0F59h 0F5Ah 0F5Bh 0F5Ch 0F5Dh 0F5Eh 0F5Fh 0F60h 0F61h 0F62h 0F63h 0F64h 0F65h 0F66h 0F67h 0F68h 0F69h 0F6Ah 0F6Bh 0F6Ch 0F6Dh 0F6Eh 0F6Fh 0F70h 0F71h 0F72h 0F73h 0F74h 0F75h Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. The 480th word The 480th word The 481st word The 481st word The 482nd word The 482nd word The 483rd word The 483rd word The 484th word The 484th word The 485th word The 485th word The 486th word The 486th word The 487th word The 487th word The 488th word The 488th word The 489th word The 489th word The 490th word The 490th word The 491st word The 491st word The 492nd word The 492nd word The 493rd word The 493rd word The 494th word The 494th word The 495th word The 495th word The 496th word The 496th word The 497th word The 497th word The 498th word The 498th word The 499th word The 499th word The 500th word The 500th word The 501st word The 501st word The 502nd word The 502nd word The 503rd word The 503rd word The 504th word The 504th word The 505th word The 505th word The 506th word The 506th word The 507th word The 507th word Register No. 43959 43960 43961 43962 43963 43964 43965 43966 43967 43968 43969 43970 43971 43972 43973 43974 43975 43976 43977 43978 43979 43980 43981 43982 43983 43984 43985 43986 43987 43988 43989 43990 43991 43992 43993 43994 43995 43996 43997 43998 43999 44000 44001 44002 44003 44004 44005 44006 44007 44008 44009 44010 44011 44012 44013 44014 Relative address 0F76h 0F77h 0F78h 0F79h 0F7Ah 0F7Bh 0F7Ch 0F7Dh 0F7Eh 0F7Fh 0F80h 0F81h 0F82h 0F83h 0F84h 0F85h 0F86h 0F87h 0F88h 0F89h 0F8Ah 0F8Bh 0F8Ch 0F8Dh 0F8Eh 0F8Fh 0F90h 0F91h 0F92h 0F93h 0F94h 0F95h 0F96h 0F97h 0F98h 0F99h 0F9Ah 0F9Bh 0F9Ch 0F9Dh 0F9Eh 0F9Fh 0FA0h 0FA1h 0FA2h 0FA3h 0FA4h 0FA5h 0FA6h 0FA7h 0FA8h 0FA9h 0FAAh 0FABh 0FACh 0FADh INP-TN5A0202-E 5.5 Address Map and Data Format Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. INP-TN5A0202-E The 508th word The 508th word The 509th word The 509th word The 510th word The 510th word The 511th word The 511th word The 512th word The 512th word The 513th word The 513th word The 514th word The 514th word The 515th word The 515th word The 516th word The 516th word The 517th word The 517th word The 518th word The 518th word The 519th word The 519th word The 520th word The 520th word The 521st word The 521st word The 522nd word The 522nd word The 523rd word The 523rd word The 524th word The 524th word The 525th word The 525th word The 526th word The 526th word The 527th word The 527th word The 528th word The 528th word The 529th word The 529th word The 530th word The 530th word The 531st word The 531st word The 532nd word The 532nd word The 533rd word The 533rd word The 534th word The 534th word The 535th word The 535th word Register No. 44015 44016 44017 44018 44019 44020 44021 44022 44023 44024 44025 44026 44027 44028 44029 44030 44031 44032 44033 44034 44035 44036 44037 44038 44039 44040 44041 44042 44043 44044 44045 44046 44047 44048 44049 44050 44051 44052 44053 44054 44055 44056 44057 44058 44059 44060 44061 44062 44063 44064 44065 44066 44067 44068 44069 44070 Relative address 0FAEh 0FAFh 0FB0h 0FB1h 0FB2h 0FB3h 0FB4h 0FB5h 0FB6h 0FB7h 0FB8h 0FB9h 0FBAh 0FBBh 0FBCh 0FBDh 0FBEh 0FBFh 0FC0h 0FC1h 0FC2h 0FC3h 0FC4h 0FC5h 0FC6h 0FC7h 0FC8h 0FC9h 0FCAh 0FCBh 0FCCh 0FCDh 0FCEh 0FCFh 0FD0h 0FD1h 0FD2h 0FD3h 0FD4h 0FD5h 0FD6h 0FD7h 0FD8h 0FD9h 0FDAh 0FDBh 0FDCh 0FDDh 0FDEh 0FDFh 0FE0h 0FE1h 0FE2h 0FE3h 0FE4h 0FE5h Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. The 536th word The 536th word The 537th word The 537th word The 538th word The 538th word The 539th word The 539th word The 540th word The 540th word The 541st word The 541st word The 542nd word The 542nd word The 543rd word The 543rd word The 544th word The 544th word The 545th word The 545th word The 546th word The 546th word The 547th word The 547th word The 548th word The 548th word The 549th word The 549th word The 550th word The 550th word The 551st word The 551st word The 552nd word The 552nd word The 553rd word The 553rd word The 554th word The 554th word The 555th word The 555th word The 556th word The 556th word The 557th word The 557th word The 558th word The 558th word The 559th word The 559th word The 560th word The 560th word The 561st word The 561st word The 562nd word The 562nd word The 563rd word The 563rd word Register No. 44071 44072 44073 44074 44075 44076 44077 44078 44079 44080 44081 44082 44083 44084 44085 44086 44087 44088 44089 44090 44091 44092 44093 44094 44095 44096 44097 44098 44099 44100 44101 44102 44103 44104 44105 44106 44107 44108 44109 44110 44111 44112 44113 44114 44115 44116 44117 44118 44119 44120 44121 44122 44123 44124 44125 44126 Relative address 0FE6h 0FE7h 0FE8h 0FE9h 0FEAh 0FEBh 0FECh 0FEDh 0FEEh 0FEFh 0FF0h 0FF1h 0FF2h 0FF3h 0FF4h 0FF5h 0FF6h 0FF7h 0FF8h 0FF9h 0FFAh 0FFBh 0FFCh 0FFDh 0FFEh 0FFFh 1000h 1001h 1002h 1003h 1004h 1005h 1006h 1007h 1008h 1009h 100Ah 100Bh 100Ch 100Dh 100Eh 100Fh 1010h 1011h 1012h 1013h 1014h 1015h 1016h 1017h 1018h 1019h 101Ah 101Bh 101Ch 101Dh 5-47 5.5 Address Map and Data Format Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. 5-48 The 564th word The 564th word The 565th word The 565th word The 566th word The 566th word The 567th word The 567th word The 568th word The 568th word The 569th word The 569th word The 570th word The 570th word The 571st word The 571st word The 572nd word The 572nd word The 573rd word The 573rd word The 574th word The 574th word The 575th word The 575th word The 576th word The 576th word The 577th word The 577th word The 578th word The 578th word The 579th word The 579th word The 580th word The 580th word The 581st word The 581st word The 582nd word The 582nd word The 583rd word The 583rd word The 584th word The 584th word The 585th word The 585th word The 586th word The 586th word The 587th word The 587th word The 588th word The 588th word The 589th word The 589th word The 590th word The 590th word The 591st word The 591st word Register No. 44127 44128 44129 44130 44131 44132 44133 44134 44135 44136 44137 44138 44139 44140 44141 44142 44143 44144 44145 44146 44147 44148 44149 44150 44151 44152 44153 44154 44155 44156 44157 44158 44159 44160 44161 44162 44163 44164 44165 44166 44167 44168 44169 44170 44171 44172 44173 44174 44175 44176 44177 44178 44179 44180 44181 44182 Relative address 101Eh 101Fh 1020h 1021h 1022h 1023h 1024h 1025h 1026h 1027h 1028h 1029h 102Ah 102Bh 102Ch 102Dh 102Eh 102Fh 1030h 1031h 1032h 1033h 1034h 1035h 1036h 1037h 1038h 1039h 103Ah 103Bh 103Ch 103Dh 103Eh 103Fh 1040h 1041h 1042h 1043h 1044h 1045h 1046h 1047h 1048h 1049h 104Ah 104Bh 104Ch 104Dh 104Eh 104Fh 1050h 1051h 1052h 1053h 1054h 1055h Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. The 592nd word The 592nd word The 593rd word The 593rd word The 594th word The 594th word The 595th word The 595th word The 596th word The 596th word The 597th word The 597th word The 598th word The 598th word The 599th word The 599th word The 600th word The 600th word The 601st word The 601st word The 602nd word The 602nd word The 603rd word The 603rd word The 604th word The 604th word The 605th word The 605th word The 606th word The 606th word The 607th word The 607th word The 608th word The 608th word The 609th word The 609th word The 610th word The 610th word The 611th word The 611th word The 612th word The 612th word The 613th word The 613th word The 614th word The 614th word The 615th word The 615th word The 616th word The 616th word The 617th word The 617th word The 618th word The 618th word The 619th word The 619th word Register No. 44183 44184 44185 44186 44187 44188 44189 44190 44191 44192 44193 44194 44195 44196 44197 44198 44199 44200 44201 44202 44203 44204 44205 44206 44207 44208 44209 44210 44211 44212 44213 44214 44215 44216 44217 44218 44219 44220 44221 44222 44223 44224 44225 44226 44227 44228 44229 44230 44231 44232 44233 44234 44235 44236 44237 44238 Relative address 1056h 1057h 1058h 1059h 105Ah 105Bh 105Ch 105Dh 105Eh 105Fh 1060h 1061h 1062h 1063h 1064h 1065h 1066h 1067h 1068h 1069h 106Ah 106Bh 106Ch 106Dh 106Eh 106Fh 1070h 1071h 1072h 1073h 1074h 1075h 1076h 1077h 1078h 1079h 107Ah 107Bh 107Ch 107Dh 107Eh 107Fh 1080h 1081h 1082h 1083h 1084h 1085h 1086h 1087h 1088h 1089h 108Ah 108Bh 108Ch 108Dh INP-TN5A0202-E 5.5 Address Map and Data Format Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. INP-TN5A0202-E The 620th word The 620th word The 621st word The 621st word The 622nd word The 622nd word The 623rd word The 623rd word The 624th word The 624th word The 625th word The 625th word The 626th word The 626th word The 627th word The 627th word The 628th word The 628th word The 629th word The 629th word The 630th word The 630th word The 631st word The 631st word The 632nd word The 632nd word The 633rd word The 633rd word The 634th word The 634th word The 635th word The 635th word The 636th word The 636th word The 637th word The 637th word The 638th word The 638th word The 639th word The 639th word The 640th word The 640th word The 641st word The 641st word The 642nd word The 642nd word The 643rd word The 643rd word The 644th word The 644th word The 645th word The 645th word The 646th word The 646th word The 647th word The 647th word Register No. 44239 44240 44241 44242 44243 44244 44245 44246 44247 44248 44249 44250 44251 44252 44253 44254 44255 44256 44257 44258 44259 44260 44261 44262 44263 44264 44265 44266 44267 44268 44269 44270 44271 44272 44273 44274 44275 44276 44277 44278 44279 44280 44281 44282 44283 44284 44285 44286 44287 44288 44289 44290 44291 44292 44293 44294 Relative address 108Eh 108Fh 1090h 1091h 1092h 1093h 1094h 1095h 1096h 1097h 1098h 1099h 109Ah 109Bh 109Ch 109Dh 109Eh 109Fh 10A0h 10A1h 10A2h 10A3h 10A4h 10A5h 10A6h 10A7h 10A8h 10A9h 10AAh 10ABh 10ACh 10ADh 10AEh 10AFh 10B0h 10B1h 10B2h 10B3h 10B4h 10B5h 10B6h 10B7h 10B8h 10B9h 10BAh 10BBh 10BCh 10BDh 10BEh 10BFh 10C0h 10C1h 10C2h 10C3h 10C4h 10C5h Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. The 648th word The 648th word The 649th word The 649th word The 650th word The 650th word The 651st word The 651st word The 652nd word The 652nd word The 653rd word The 653rd word The 654th word The 654th word The 655th word The 655th word The 656th word The 656th word The 657th word The 657th word The 658th word The 658th word The 659th word The 659th word The 660th word The 660th word The 661st word The 661st word The 662nd word The 662nd word The 663rd word The 663rd word The 664th word The 664th word The 665th word The 665th word The 666th word The 666th word The 667th word The 667th word The 668th word The 668th word The 669th word The 669th word The 670th word The 670th word The 671st word The 671st word The 672nd word The 672nd word The 673rd word The 673rd word The 674th word The 674th word The 675th word The 675th word Register No. 44295 44296 44297 44298 44299 44300 44301 44302 44303 44304 44305 44306 44307 44308 44309 44310 44311 44312 44313 44314 44315 44316 44317 44318 44319 44320 44321 44322 44323 44324 44325 44326 44327 44328 44329 44330 44331 44332 44333 44334 44335 44336 44337 44338 44339 44340 44341 44342 44343 44344 44345 44346 44347 44348 44349 44350 Relative address 10C6h 10C7h 10C8h 10C9h 10CAh 10CBh 10CCh 10CDh 10CEh 10CFh 10D0h 10D1h 10D2h 10D3h 10D4h 10D5h 10D6h 10D7h 10D8h 10D9h 10DAh 10DBh 10DCh 10DDh 10DEh 10DFh 10E0h 10E1h 10E2h 10E3h 10E4h 10E5h 10E6h 10E7h 10E8h 10E9h 10EAh 10EBh 10ECh 10EDh 10EEh 10EFh 10F0h 10F1h 10F2h 10F3h 10F4h 10F5h 10F6h 10F7h 10F8h 10F9h 10FAh 10FBh 10FCh 10FDh 5-49 5.5 Address Map and Data Format Contents Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. Monitor area entry St. No. Monitor area entry register No. 5-50 The 676th word The 676th word The 677th word The 677th word The 678th word The 678th word The 679th word The 679th word The 680th word The 680th word The 681st word The 681st word The 682nd word The 682nd word The 683rd word The 683rd word The 684th word The 684th word The 685th word The 685th word The 686th word The 686th word The 687th word The 687th word The 688th word The 688th word The 689th word The 689th word The 690th word The 690th word The 691st word The 691st word The 692nd word The 692nd word The 693rd word The 693rd word The 694th word The 694th word The 695th word The 695th word The 696th word The 696th word The 697th word The 697th word The 698th word The 698th word The 699th word The 699th word The 700th word The 700th word The 701st word The 701st word The 702nd word The 702nd word The 703rd word The 703rd word Register No. 44351 44352 44353 44354 44355 44356 44357 44358 44359 44360 44361 44362 44363 44364 44365 44366 44367 44368 44369 44370 44371 44372 44373 44374 44375 44376 44377 44378 44379 44380 44381 44382 44383 44384 44385 44386 44387 44388 44389 44390 44391 44392 44393 44394 44395 44396 44397 44398 44399 44400 44401 44402 44403 44404 44405 44406 Relative address 10FEh 10FFh 1100h 1101h 1102h 1103h 1104h 1105h 1106h 1107h 1108h 1109h 110Ah 110Bh 110Ch 110Dh 110Eh 110Fh 1110h 1111h 1112h 1113h 1114h 1115h 1116h 1117h 1118h 1119h 111Ah 111Bh 111Ch 111Dh 111Eh 111Fh 1120h 1121h 1122h 1123h 1124h 1125h 1126h 1127h 1128h 1129h 112Ah 112Bh 112Ch 112Dh 112Eh 112Fh 1130h 1131h 1132h 1133h 1134h 1135h Contents Monitor area entry St. No. The 704th word Monitor area entry register No. The 704th word Monitor area entry St. No. The 705th word Monitor area entry register No. The 705th word Monitor area entry St. No. The 706th word Monitor area entry register No. The 706th word Monitor area entry St. No. The 707th word Monitor area entry register No. The 707th word Monitor area entry St. No. The 708th word Monitor area entry register No. The 708th word Monitor area entry St. No. The 709th word Monitor area entry register No. The 709th word Monitor area entry St. No. The 710th word Monitor area entry register No. The 710th word Monitor area entry St. No. The 711th word Monitor area entry register No. The 711th word Monitor area entry St. No. The 712th word Monitor area entry register No. The 712th word Setting fault PLC error counter PLC error code PLC sending counter PLC receiving counter Inter-PLC communication execution time monitor PLC inter-cycle time over counter Register No. 44407 44408 44409 44410 44411 44412 44413 44414 44415 44416 44417 44418 44419 44420 44421 44422 44423 44424 30232 31001 31002 31003 31004 31007 31008 Relative address 1136h 1137h 1138h 1139h 113Ah 113Bh 113Ch 113Dh 113Eh 113Fh 1140h 1141h 1142h 1143h 1144h 1145h 1146h 1147h 00E7h 03E8h 03E9h 03EAh 03EBh 03EEh 03EFh INP-TN5A0202-E 5.6 Setting/Monitor Area Entry Numbers (Control module) 5.6 Setting/Monitor Area Entry Numbers (Control module) The table below shows the register numbers of a control module, which are settable to each parameter of "Setting/Monitor area entry St. No." and "Setting/Monitor area entry register No." of a programless communication module. Note Parameters marked "*" in the "Entry ban" column in the table can not be changed via programless communication modules. Do not set them to each parameter of "Setting/Monitor area entry St. No." and "Setting/Monitor area entry register No." Operation parameter Contents Local SV value Reading out/Writing data setting range 0 to 100% FS Communication SV value 0 to 100% FS MV value -3.0 to 103.0% Manual mode switch 0: Auto 1: Manual 0: RUN 1: Standby 0: Local 1: Remote 0: Stop/End 1: Normal type 2: Low PV type 0: OFF 1: Unlatch -100 to 100% FS -100 to 100% FS -100 to 100% FS -100 to 100% FS -100 to 100% FS -100 to 100% FS -100 to 100% FS -100 to 100% FS -100 to 100% FS -100 to 100% FS RUN/Standby switch Remote mode switch Auto-tuning RUN command DO output unlatch command ALM1 set value 1 ALM1 set value 2 ALM2 set value 1 ALM2 set value 2 ALM3 set value 1 ALM3 set value 2 ALM4 set value 1 ALM4 set value 2 ALM5 set value 1 ALM5 set value 2 INP-TN5A0202-E Register Depends Factory-set No.1 on Input value (Ch1) range 0 40001 c 41001 0 40023 c 41100 40005 41002 0 (Auto) 40013 41003 0 (RUN) 40017 41004 0 (Local) 40009 41007 0 41005 c c c c c c c c c c Register No.2 (Ch2) 40002 42001 40024 42100 40006 42002 40014 42003 40018 42004 40010 42007 42005 Register No.3 (Ch3) 40003 43001 40025 43100 40007 43002 40015 43003 40019 43004 40011 43007 43005 Register No.4 (Ch4) 40004 44001 40026 44100 40008 44002 40016 44003 40020 44004 40012 44007 44005 0 41031 42031 43031 44031 2.5% FS 2.5% FS 2.5% FS 2.5% FS 2.5% FS 2.5% FS 2.5% FS 2.5% FS 2.5% FS 2.5% FS 41033 41034 41041 41042 41049 41050 41057 41058 41065 41066 42033 42034 42041 42042 42049 42050 42057 42058 42065 42066 43033 43034 43041 43042 43049 43050 43057 43058 43065 43066 44033 44034 44041 44042 44049 44050 44057 44058 44065 44066 Entry ban * 5-51 5.6 Setting/Monitor Area Entry Numbers (Control module) Control (PID) Parameters Contents Proportional band [P] Integration time [I] Derivation time [D] ON/OFF control hysteresis Cooling proportional band coefficient [cool] Dead band Output convergence value Anti-reset windup [ARW] Direct/Reverse action setting [MV1/MV2] SV Lower Limit SV Upper Limit MV1 Lower Limit MV1 Upper Limit MV2 Lower Limit MV2 Upper Limit Output limiter type setting 5-52 Depends Reading out/Writing data on Input setting range range 0.0 to 999.9% 0 to 3200sec 0.0 to 999.9sec 0 to 50% FS 0.0 to 100.0 -50.0 to 50.0% -100.0 to 100.0% 0 to 100% FS 0: Reverse/None 1: Direct/None 2: Reverse/Direct 3: Direct/Reverse 4: Reverse/Reverse 5: Direct/Direct 0 to 100% FS 0 to 100% FS -3.0 to 103.0% -3.0 to 103.0% -3.0 to 103.0% -3.0 to 103.0% 0: MV1 -3.0%/103.0% MV2 -3.0%/103.0% 1: MV1 Limit/103.0% MV2 -3.0%/103.0% 2: MV1 -3.0%/Limit MV2 -3.0%/103.0% 3: MV1 Limit/ Limit MV2 -3.0%/103.0% 4: MV1 -3.0%/103.0% MV2 Limit/103.0% 5: MV1 Limit/103.0% MV2 Limit/103.0% 6: MV1 -3.0%/Limit MV2 Limit/103.0% 7: MV1 Limit/Limit MV2 Limit/103.0% 8: MV1 -3.0%/103.0% MV2 -3.0%/Limit 9: MV1 Limit/103.0% MV2 -3.0%/Limit 10: MV1 -3.0%/Limit MV2 -3.0%/Limit 11: MV1 Limit/Limit MV2 -3.0%/Limit 12: MV1 -3.0%/103.0% MV2 Limit/Limit 13: MV1 Limit/103.0% MV2 Limit/Limit 14: MV1 -3.0%/Limit MV2 Limit/Limit 15: MV1 Limit/Limit MV2 Limit/Limit c c c c 5.0 240 Register No.1 (Ch1) 41102 41103 Register No.2 (Ch2) 42102 42103 Register No.3 (Ch3) 43102 43103 Register No.4 (Ch4) 44102 44103 60.0 0.25% FS 1.0 0 0 100% FS 0 41104 41105 41106 41107 41108 41109 41110 42104 42105 42106 42107 42108 42109 42110 43104 43105 43106 43107 43108 43109 43110 44104 44105 44106 44107 44108 44109 44110 0% FS 100% FS -3.0 103.0 -3.0 103.0 0 41218 41219 41255 41256 41257 41258 41259 42218 42219 42255 42256 42257 42258 42259 43218 43219 43255 43256 43257 43258 43259 44218 44219 44255 44256 44257 44258 44259 Factoryset value Entry ban INP-TN5A0202-E 5.6 Setting/Monitor Area Entry Numbers (Control module) Setup Parameters Contents PV input type PV input scale lower Reading out/Writing data setting range Depends on Input range 0: JPt100 (0 to 150°C) 1: JPt100 (-150 to 600°C) 2: Pt100 (0 to 150°C) 3: Pt100 (-150 to 300°C) 4: Pt100 (-150 to 850°C) 5: J (0 to 400°C) 6: J (0 to 800°C) 7: K (0 to 400°C) 8: K (0 to 800°C) 9: K (0 to 1200°C) 10: R (0 to 1600°C) 11: B (0 to 1800°C) 12: S (0 to 1600°C) 13: T (-199 to 400°C) 14: E (-199 to 800°C) 18: N (0 to 1300°C) 19: PL-2 (0 to 1300°C) 21: Voltage (0 to 5V) 22: Voltage (1 to 5V) 23: Voltage (0 to 10V) 24: Voltage (2 to 10V) -1999 to 9999 PV input scale upper Decimal place -1999 to 9999 0: No decimal point 1: One decimal place 2: Two decimal places Temperature unit 0: °C 1: Not selectable PV input shift -10 to 10% FS SV set value shift -50 to 50% FS PV input filter 0.0 to 120.0sec PV display zero adjustment -50 to 50% FS PV display span adjustment -50 to 50% FS Cold junction compensation 0: OFF 1: ON RSV zero adjustment -50 to 50% FS RSV span adjustment -50 to 50% FS Remote input master St. 0 to 255 No. INP-TN5A0202-E c c c c c c 7(TC/Pt) 22(VI) Register Register Register Register No.4 No.3 No.2 No.1 (Ch4) (Ch3) (Ch2) (Ch1) 40151 40152 40153 40154 41029 42029 43029 44029 0% FS 41212 42212 43212 44212 100% FS 0 41213 41214 42213 42214 43213 43214 44213 44214 * * * °C 41215 42215 43215 44215 * 0 0 2.0 0 0 1 (ON) 41216 41217 41220 41221 41222 41223 42216 42217 42220 42221 42222 42223 43216 43217 43220 43221 43222 43223 44216 44217 44220 44221 44222 44223 0 0 0 41225 41226 41532 42225 42226 42532 43225 43226 43532 44225 44226 44532 Factory-set value Entry ban * * 5-53 5.6 Setting/Monitor Area Entry Numbers (Control module) Remote input master Ch. No. FAULT MV1 set value FAULT MV2 set value SoftStart MV1 value SoftStart MV2 value SoftStart time Standby MV1 value Standby MV2 value Standby mode setting Linkage operation master St. No. setting Linkage operation master Ch. No. setting Register No.2 (Ch2) 42533 42260 42261 42262 42263 42264 42268 42269 42270 Register No.3 (Ch3) 43533 43260 43261 43262 43263 43264 43268 43269 43270 Register No.4 (Ch4) 44533 44260 44261 44262 44263 44264 44268 44269 44270 0/1 to 4 -3.0 to 103.0% -3.0 to 103.0% -3.0 to 103.0% -3.0 to 103.0% 0 to 99min. 59sec. -3.0 to 103.0% -3.0 to 103.0% 0: ALM=OFF 1: ALM=ON 0 to 255 Each Ch. -3.0 -3.0 103.0 103.0 0 -3.0 -3.0 0 Register No.1 (Ch1) 41533 41260 41261 41262 41263 41264 41268 41269 41270 0 41536 42536 43536 44536 * 1 to 4 Each Ch. 41537 42537 43537 44537 * Register No.1 (Ch1) 40166 41801 40171 41803 Register No.2 (Ch2) 40167 42801 40177 42803 Register No.3 (Ch3) 40168 43801 40183 43803 Register No.4 (Ch4) 40169 44801 40189 44803 40182 40188 40194 Reading out/Writing data setting range Contents Depends on Input range Factory-set value Entry ban * * * * System Parameters Contents Current output range Reading out/Writing data setting range Proportional cycle 4: 0 to 20mA 5: 4 to 20mA 0: Own St. PV 1: Own St. SV 2: Own St. DV 3: Own St. MV 1 4: Own St. MV 2 5: Other St. PV 6: Other St. SV 7: Other St. MV 1 to 120sec. Output master St. 0 to255 St. Output master Ch. 1 to 4Ch Output scaling base -100.0 to 100.0% Output scaling span -100.0 to 100.0% Output shutdown 0000 to 1111 bit0: Output 1 shutdown bit1: Output 2 shutdown bit2: Output 3 shutdown bit3: Output 4 shutdown Output type 5-54 Depends on Input range Factory-set value 5 (4-20mA) 3 (Own St. MV1) 2 (SSR drive) 40176 /30 (relay) 0 40172 41804 Each Ch. 40173 41805 0.0 40175 41807 100.0 40174 41806 0000 40178 42804 40179 42805 40181 42807 40180 42806 40184 43804 40185 43805 40187 43807 40186 43806 40201 40190 44804 40191 44805 40193 44807 40192 44806 Entry ban * * INP-TN5A0202-E 5.6 Setting/Monitor Area Entry Numbers (Control module) Contents DI-1 function select INP-TN5A0202-E Reading out/Writing data setting range 0: No function 1: RUN /Standby switch 2: Auto/Manual switch 3: Local /Remote switch 4: No function 5: No function 6: Start AT (Normal type) 7: Start AT (Low voltage PV) 8: No function 9: No function 10: Ramp SV ON/OFF 11: Ramp SV Hold 12: No function 13: No function 14: No function 15: No function 16: No function 17: Unlatch (All) 18: Unlatch (DO1) 19: Unlatch (DO2) 20: Unlatch (DO3) 21: Unlatch (DO4) 22: Unlatch (DO5) 23: No function 24: No function 25: No function 26: Start timer (DO1) 27: Start timer (DO2) 28: Start timer (DO3) 29: Start timer (DO4) 30: Start timer (DO5) 31: No function 32: No function 33: No function 34: No function 35: No function Depends on Input range Factory-set value 0 Register Register Register Register No.4 No.3 No.2 No.1 (Ch4) (Ch3) (Ch2) (Ch1) 41013 42013 43013 44013 Entry ban 5-55 5.6 Setting/Monitor Area Entry Numbers (Control module) Contents Reading out/Writing data setting range 36: No function 37: No function 38: No function 39: No function 40: No function 41: No function 42: No function 43: No function 44: No function 45: No function 46: No function 47: No function 48: No function 49: Output1 shutdown 50: Output2 shutdown 51: Output3 shutdown 52: Output4 shutdown DI-2 function select 0 to 52 DI-3 function select 0 to 52 DI-4 function select 0 to 52 DI-5 function select 0 to 52 DI-6 function select 0 to 52 DI-7 function select 0 to 52 DI-8 function select 0 to 52 DI-9 function select 0 to 52 DI-10 function select 0 to 52 DI-11 function select 0 to 52 DI-12 function select 0 to 52 DI-13 function select 0 to 52 DI-14 function select 0 to 52 DI-15 function select 0 to 52 DI-16 function select 0 to 52 DI master St. setting 0 to 255 DO1 output event type setting 0 to 102 DO1 option function setting 0000 to 1111 bit0: Alarm latch function bit1: Error input alarm function bit2: Non-excitation output function bit3: Hold reset function DO2 output event type setting 0 to 102 DO2 option function setting 0000 to 1111 bit0: Alarm latch function bit1: Error input alarm function bit2: Non-excitation output function bit3: Hold reset function DO3 output event type setting 0 to 102 Depends on Input range Factory-set value Register Register Register Register No.4 No.3 No.2 No.1 (Ch4) (Ch3) (Ch2) (Ch1) Entry ban DI-1 function select 5-56 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0000 41014 41015 41016 41017 41018 41019 41020 41021 41022 41023 41024 41025 41026 41027 41028 41011 41032 41036 42014 42015 42016 42017 42018 42019 42020 42021 42022 42023 42024 42025 42026 42027 42028 42011 42032 42036 43014 43015 43016 43017 43018 43019 43020 43021 43022 43023 43024 43025 43026 43027 43028 43011 43032 43036 44014 44015 44016 44017 44018 44019 44020 44021 44022 44023 44024 44025 44026 44027 44028 44011 44032 44036 0 0000 41040 41044 42040 42044 43040 43044 44040 44044 * 0 41048 42048 43048 44048 * * * INP-TN5A0202-E 5.6 Setting/Monitor Area Entry Numbers (Control module) Contents Reading out/Writing data setting range DO3 option function setting 0000 to 1111 bit0: Alarm latch function bit1: Error input alarm function bit2: Non-excitation output function bit3: Hold reset function DO4 output event type setting 0 to 102 DO4 option function setting 0000 to 1111 bit0: Alarm latch function bit1: Error input alarm function bit2: Non-excitation output function bit3: Hold reset function DO5 output event type setting 0 to 102 DO5 option function setting 0000 to 1111 bit0: Alarm latch function bit1: Error input alarm function bit2: Non-excitation output function bit3: Hold reset function Ramp SV ON/OFF 0: OFF 1: ON Ramp SV-decline 0 to 100% FS Ramp SV-incline 0 to 100% FS Ramp SV slope time units 0: Slope deg/hr. 1: Slope deg/min. Control method 0: PID 1: FUSSY PID 2: PID against open-loop ON/OFF hysteresis setting 0: OFF 1: ON Mode at startup 0: Auto 1: Manual 2: Remote 3: Standby INP-TN5A0202-E Depends on Input range c c 0000 Register Register Register Register No.4 No.3 No.2 No.1 (Ch4) (Ch3) (Ch2) (Ch1) 41052 42052 43052 44052 0 0000 41056 41060 42056 42060 43056 43060 44056 44060 * 0 0000 41064 41068 42064 42068 43064 43068 44064 44068 * 1 (ON) 41299 42299 43299 44299 0 0 0 (Slope deg/ hr.) 0 (PID) 41300 41301 41302 42300 42301 42302 43300 43301 43302 44300 44301 44302 41291 42291 43291 44291 1 (ON) 41292 42292 43292 44292 0 (Auto) 41304 42304 43304 44304 Factory-set value Entry ban * 5-57 5.6 Setting/Monitor Area Entry Numbers (Control module) Alarm Parameters Contents ALM1 hysteresis ALM1 delay time ALM1 delay time units ALM2 hysteresis ALM2 delay time ALM2 delay time units ALM3 hysteresis ALM3 delay time ALM3 delay time units ALM4 hysteresis ALM4 delay time ALM4 delay time units ALM5 hysteresis ALM5 delay time ALM5 delay time units Object Ch. No. for interchannel ALM1 Object Ch. No. for interchannel ALM2 Object Ch. No. for interchannel ALM3 Object Ch. No. for interchannel ALM4 Object Ch. No. for interchannel ALM5 CT[A]HB alarm set value CT[A]HB alarm hysteresis CT[A]HB load short-circuit alarm set value CT[A]HB load short-circuit alarm hysteresis CT[B]HB alarm set value CT[B]HB alarm hysteresis CT[B]HB load short-circuit alarm set value CT[B]HB load short-circuit alarm hysteresis Loop break detection time Loop break detection band 5-58 Reading out/Writing data setting range 0 to 50% FS 0 to 99min.59sec. / 0 to 99hr.59min. 0: sec. 1: min. 0 to 50% FS 0 to 99min.59sec. / 0 to 99hr.59min. 0: sec. 1: min. 0 to 50% FS 0 to 99min.59sec. / 0 to 99hr.59min. 0: sec. 1: min. 0 to 50% FS 0 to 99min.59sec. / 0 to 99hr.59min. 0: sec. 1: min. 0 to 50% FS 0 to 99min.59sec. / 0 to 99hr.59min. 0: sec. 1: min. 1 to 4 Depends Factory-set on Input value range 1°C c 0 Register Register Register Register No.4 No.3 No.2 No.1 (Ch4) (Ch3) (Ch2) (Ch1) 41035 42035 43035 44035 41037 42037 43037 44037 0 (sec.) 41038 42038 43038 44038 1°C 0 41043 41045 42043 42045 43043 43045 44043 44045 0 (sec.) 41046 42046 43046 44046 1°C 0 41051 41053 42051 42053 43051 43053 44051 44053 0 (sec.) 41054 42054 43054 44054 1°C 0 41059 41061 42059 42061 43059 43061 44059 44061 0 (sec.) 41062 42062 43062 44062 1°C 0 41067 41069 42067 42069 43067 43069 44067 44069 0 (sec.) 41070 42070 43070 44070 1 41039 42039 43039 44039 1 to 4 1 41047 42047 43047 44047 1 to 4 1 41055 42055 43055 44055 1 to 4 1 41063 42063 43063 44063 1 to 4 1 41071 42071 43071 44071 0.0 to 50.0(A) 0.0 to 50.0(A) 0.0 to 50.0(A) 0 0.5 0 41072 41073 41074 42072 42073 42074 43072 43073 43074 44072 44073 44074 0.0 to 50.0(A) 0.5 41075 42075 43075 44075 0.0 to 50.0(A) 0.0 to 50.0(A) 0.0 to 50.0(A) 0 0.5 0 41076 41077 41078 42076 42077 42078 43076 43077 43078 44076 44077 44078 0.0 to 50.0(A) 0.5 41079 42079 43079 44079 0 (Off) 2.5% FS 41080 41081 42080 42081 43080 43081 44080 44081 0 to 9999sec 0 to 100% FS c c c c c Entry ban INP-TN5A0202-E 5.6 Setting/Monitor Area Entry Numbers (Control module) Communication Parameters Contents RS-485 Parity setting Reading out/Writing data setting range 0: None 1: Odd 2: Even RS-485 Communication 0: 9.6kbps speed 1: 19.2kbps 2: 38.4kbps 3: Forbidden 4: 115.2kbps RS-485 Communication 0: Ready only permission 1: Read/Write RS-485 Response interval 0 to 25 (20ms/1digit) time Enhanced communication 0: PUMC not connected module (PUMC) (RS-485 Enable) connection permission 1: PUMC connected (RS-485 Disable) Master/slave setting in 0: Master connected modules 1: Slave User address 01 : 30000 to 49999 Register No. specification User address 02 : 30000 to 49999 Register No. specification User address 03 : 30000 to 49999 Register No. specification User address 04 : 30000 to 49999 Register No. specification User address 05 : 30000 to 49999 Register No. specification User address 06 : 30000 to 49999 Register No. specification User address 07 : 30000 to 49999 Register No. specification User address 08 : 30000 to 49999 Register No. specification User address 09 : 30000 to 49999 Register No. specification User address 10 : 30000 to 49999 Register No. specification User address 11 : 30000 to 49999 Register No. specification User address 12 : 30000 to 49999 Register No. specification User address 13 : 30000 to 49999 Register No. specification User address 14 : 30000 to 49999 Register No. specification User address 15 : 30000 to 49999 Register No. specification User address 16 : 30000 to 49999 Register No. specification User address 17 : 30000 to 49999 Register No. specification INP-TN5A0202-E 0 Register Register Register Register No.4 No.3 No.2 No.1 (Ch4) (Ch3) (Ch2) (Ch1) 40111 1 40115 * 1 (R/W) 40114 * 0 40113 * 0 (RS-485 Enable) 40116 * 1 (Slave) 40117 * 30002(PV1) 40301 * 30002(PV1) 40302 * 30002(PV1) 40303 * 30002(PV1) 40304 * 30002(PV1) 40305 * 30002(PV1) 40306 * 30002(PV1) 40307 * 30002(PV1) 40308 * 30002(PV1) 40309 * 30002(PV1) 40310 * 30002(PV1) 40311 * 30002(PV1) 40312 * 30002(PV1) 40313 * 30002(PV1) 40314 * 30002(PV1) 40315 * 30002(PV1) 40316 * 30002(PV1) 40317 * Depends on Input range Factory-set value Entry ban * 5-59 5.6 Setting/Monitor Area Entry Numbers (Control module) Contents User address 18 : Register No. specification User address 19 : Register No. specification User address 20 : Register No. specification User address 21 : Register No. specification User address 22 : Register No. specification User address 23 : Register No. specification User address 24 : Register No. specification User address 25 : Register No. specification User address 26 : Register No. specification User address 27 : Register No. specification User address 28 : Register No. specification User address 29 : Register No. specification User address 30 : Register No. specification User address 31 : Register No. specification User address 32 : Register No. specification User address 01 : R/W field User address 02 : R/W field User address 03 : R/W field User address 04 : R/W field User address 05 : R/W field User address 06 : R/W field User address 07 : R/W field User address 08 : R/W field User address 09 : R/W field User address 10 : R/W field User address 11 : R/W field User address 12 : R/W field 5-60 30000 to 49999 30002(PV1) Register Register Register Register No.4 No.3 No.2 No.1 (Ch4) (Ch3) (Ch2) (Ch1) 40318 30000 to 49999 30002(PV1) 40319 * 30000 to 49999 30002(PV1) 40320 * 30000 to 49999 30002(PV1) 40321 * 30000 to 49999 30002(PV1) 40322 * 30000 to 49999 30002(PV1) 40323 * 30000 to 49999 30002(PV1) 40324 * 30000 to 49999 30002(PV1) 40325 * 30000 to 49999 30002(PV1) 40326 * 30000 to 49999 30002(PV1) 40327 * 30000 to 49999 30002(PV1) 40328 * 30000 to 49999 30002(PV1) 40329 * 30000 to 49999 30002(PV1) 40330 * 30000 to 49999 30002(PV1) 40331 * 30000 to 49999 30002(PV1) 40332 * Depends on "User address 01" Depends on "User address 02" Depends on "User address 03" Depends on "User address 04" Depends on "User address 05" Depends on "User address 06" Depends on "User address 07" Depends on "User address 08" Depends on "User address 09" Depends on "User address 10" Depends on "User address 11" Depends on "User address 12" - 45001 * - 45002 * - 45003 * - 45004 * - 45005 * - 45006 * - 45007 * - 45008 * - 45009 * - 45010 * - 45011 * - 45012 * Reading out/Writing data setting range Depends on Input range Factory-set value Entry ban * INP-TN5A0202-E 5.6 Setting/Monitor Area Entry Numbers (Control module) Contents User address 13 : R/W field User address 14 : R/W field User address 15 : R/W field User address 16 : R/W field User address 17 : R/W field User address 18 : R/W field User address 19 : R/W field User address 20 : R/W field User address 21 : R/W field User address 22 : R/W field User address 23 : R/W field User address 24 : R/W field User address 25 : R/W field User address 26 : R/W field User address 27 : R/W field User address 28 : R/W field User address 29 : R/W field User address 30 : R/W field User address 31 : R/W field User address 32 : R/W field INP-TN5A0202-E Reading out/Writing data setting range Depends on "User address 13" Depends on "User address 14" Depends on "User address 15" Depends on "User address 16" Depends on "User address 17" Depends on "User address 18" Depends on "User address 19" Depends on "User address 20" Depends on "User address 21" Depends on "User address 22" Depends on "User address 23" Depends on "User address 24" Depends on "User address 25" Depends on "User address 26" Depends on "User address 27" Depends on "User address 28" Depends on "User address 29" Depends on "User address 30" Depends on "User address 31" Depends on "User address 32" - Register Register Register Register No.4 No.3 No.2 No.1 (Ch4) (Ch3) (Ch2) (Ch1) 45013 - 45014 * - 45015 * - 45016 * - 45017 * - 45018 * - 45019 * - 45020 * - 45021 * - 45022 * - 45023 * - 45024 * - 45025 * - 45026 * - 45027 * - 45028 * - 45029 * - 45030 * - 45031 * - 45032 * Depends on Input range Factory-set value Entry ban * 5-61 5.6 Setting/Monitor Area Entry Numbers (Control module) Configuration Parameters Contents Reading out/Writing data setting range Depends on Input range Register Register Register Register No.4 No.3 No.2 No.1 (Ch4) (Ch3) (Ch2) (Ch1) 0 (Stop control) 41407 42407 43407 44407 Factory-set value Control when burnout is 0: Stop control detected 1: Continue control LED2 Lamp Configuration 0 to 255 1 40222 LED3 Lamp Configuration LED4 Lamp Configuration LED5 Lamp Configuration LED6 Lamp Configuration Reset main unit 12 13 14 15 0 40223 40224 40225 40226 40101 0 to 255 0 to 255 0 to 255 0 to 255 0: Do nothing 1: Reset main unit Entry ban * * * * * * Monitor Parameters Note Monitor parameter can be entered to the monitor area only. Do not enter it to the setting area. Contents SV value Remote mode switch Reading out/Writing data setting range System time Measurement value (PV) 0 to 100% FS 0: Local 1: Remote 0 to 65535 -5 to 105% FS Measurement value (SV) 0 to 100% FS DV -105 to 105% FS Output value (MV1) -3.0 to 103.0% Output value (MV2) -3.0 to 103.0% Remote SV (RSV) 0.0 to 100.0% FS RCJtemp Heater current [A] -3276.7 to 3276.7°C 0.0 to 50.0A Heater current [B] 0.0 to 50.0A Leak current [A] 0.0 to 50.0A 5-62 Register Depends Factory-set No.1 on Input value (Ch1) range c 30905 30030 31037 30002 31001 30006 31002 30010 31003 30014 31004 30015 31005 30022 31045 30110 31016 30071 31046 30072 31047 30081 31048 Register Register No.3 No.2 (Ch3) (Ch2) 30906 30907 30031 30032 32037 33037 30001 30003 30004 32001 33001 30007 30008 32002 33002 30011 30012 32003 33003 30016 30018 32004 33004 30017 30019 32005 33005 30023 30024 32045 33045 30111 30112 32016 33016 30073 30075 32046 33046 30074 30076 32047 33047 30083 30085 32048 33048 Register No.4 (Ch4) 30908 30033 34037 Entry ban 30005 34001 30009 34002 30013 34003 30020 34004 30021 34005 30025 34045 30113 34016 30077 34046 30078 34047 30087 34048 INP-TN5A0202-E 5.6 Setting/Monitor Area Entry Numbers (Control module) Contents Reading out/Writing data setting range Leak current [B] 0.0 to 50.0A Error source display Alarm 1 to 5 status Event input status Remaining time on timer 1 0 to FFFF 0 to 001F 0 to FFFF 0 to 99min.59sec. / 0 to 99hr. 59min. 0 to 99min.59sec. / 0 to 99hr. 59min. 0 to 99min.59sec. / 0 to 99hr. 59min. 0 to 99min.59sec. / 0 to 99hr. 59min. 0 to 99min.59sec. / 0 to 99hr. 59min. -3.0 to 103.0% 0: Read only 1: Read/ Write Remaining time on timer 2 Remaining time on timer 3 Remaining time on timer 4 Remaining time on timer 5 Output value RS-485 communication permission INP-TN5A0202-E Register Register Depends Factory-set No.2 No.1 on Input value (Ch2) (Ch1) range 30082 30084 31049 32049 31008 32008 31007 32007 31061 32061 31011 32011 Register No.3 (Ch3) 30086 33049 33008 33007 33061 33011 Register No.4 (Ch4) 30088 34049 34008 34007 34061 34011 - 31012 32012 33012 34012 - 31013 32013 33013 34013 - 31014 32014 33014 34014 - 31015 32015 33015 34015 - 30120 30121 30122 30062 30123 Entry ban 5-63 5.7 Setting/Monitor Area Entry Numbers (Event I/O module) 5.7 Setting/Monitor Area Entry Numbers (Event I/O module) The table below shows the register numbers of an event I/O module, which are settable to each parameter of "Setting/Monitor area entry St. No." and "Setting/Monitor area entry register No." of a programless communication module. Note Parameters marked "*" in the "Entry ban" column in the table can not be changed via programless communication modules. Do not set them to each parameter of "Setting/Monitor area entry St. No." and "Setting/Monitor area entry register No." Operation Parameters Contents Reading out/Writing data setting range Factory-set value Register No. RUN/Standby Switch 0: RUN 1: Standby 0 40021 DI output unlatch command 0: OFF 1: Unlatch 0 40022 DO output unlatch command 0: OFF 1: Unlatch 0 40023 5-64 Entry ban INP-TN5A0202-E 5.7 Setting/Monitor Area Entry Numbers (Event I/O module) Digital Input Parameters Contents Reading out/Writing data setting range Factory-set value Register No. DI1 input option Bit 0 : LATCH Bit 1 : NOT Bit 2 : AND Bit 3 : OR 0 40701 DI1 input logic operation AND 0-00FF 0 40703 DI1 input logic operation OR 0-00FF 0 40704 DI2 input option 0-15 0 40705 DI2 input logic operation AND 0-00FF 0 40707 DI2 input logic operation OR 0-00FF 0 40708 DI3 input option 0-15 0 40709 DI3 input logic operation AND 0-00FF 0 40711 DI3 input logic operation OR 0-00FF 0 40712 DI4 input option 0-15 0 40713 DI4 input logic operation AND 0-00FF 0 40715 DI4 input logic operation OR 0-00FF 0 40716 DI5 input option 0-15 0 40717 DI5 input logic operation AND 0-00FF 0 40719 DI5 input logic operation OR 0-00FF 0 40720 DI6 input option 0-15 0 40721 DI6 input logic operation AND 0-00FF 0 40723 DI6 input logic operation OR 0-00FF 0 40724 DI7 input option 0-15 0 40725 DI7 input logic operation AND 0-00FF 0 40727 DI7 input logic operation OR 0-00FF 0 40728 DI8 input option 0-15 0 40729 DI8 input logic operation AND 0-00FF 0 40731 DI8 input logic operation OR 0-00FF 0 40732 INP-TN5A0202-E Entry ban 5-65 5.7 Setting/Monitor Area Entry Numbers (Event I/O module) Digital Output Parameters Contents Reading out/Writing data setting range Factory-set value Register No. Entry ban DO1 output type 0: Event output 1: Control output 0 40401 * DO1 master St. No. 0-255 0 40402 DO1 master Ch. No. 1-4 1 40403 * * DO1 BIT position 0-FFFF 1 40404 DO1 output option Bit 0 : LATCH Bit 1 : NOT Bit 2 : AND Bit 3 : OR 0 40405 DO1 output logic operation AND 0-00FF 0 40407 DO1 output logic operation OR 0-00FF 0 40408 DO1 scaling base -100.0 - +100.0 0 40409 DO1 scaling span -100.0 - +100.0 1000 40410 DO1 proportion cycle 1-120 30 40411 DO1 output limit (lower) 0.0 - 100.0 0 40412 DO1 output limit (upper) 0.0 - 100.0 1000 40413 DO1 limit type 0: Lower limit -3%, Upper limit 103% 1: Lower limit, Upper limit 103% 2: Lower limit -3%, Upper limit 3: Lower limit, Upper limit 0 40414 DO2 output type 0: Event output 1: Control output 0 40415 * DO2 master St. No. 0-255 0 40416 DO2 master Ch. No. 1-4 1 40417 * * DO2 BIT position 0-FFFF 2 40418 DO2 output option 0-15 0 40419 DO2 output logic operation AND 0-00FF 0 40421 DO2 output logic operation OR 0-00FF 0 40422 DO2 scaling base -100.0 - +100.0 0 40423 DO2 scaling span -100.0 - +100.0 1000 40424 DO2 proportion cycle 1-120 30 40425 DO2 output limit (lower) 0.0 - 100.0 0 40426 DO2 output limit (upper) 0.0 - 100.0 1000 40427 DO2 limit type 0-3 0 40428 DO3 output type 0: Event output 1: Control output 0 40429 * DO3 master St. No. 0-255 0 40430 DO3 master Ch. No. 1-4 1 40431 * * DO3 BIT position 0-FFFF 4 40432 5-66 INP-TN5A0202-E 5.7 Setting/Monitor Area Entry Numbers (Event I/O module) Contents Reading out/Writing data setting range Factory-set value Register No. Entry ban DO3 output option 0-15 0 40433 DO3 output logic operation AND 0-00FF 0 40435 DO3 output logic operation OR 0-00FF 0 40436 DO3 scaling base -100.0 - +100.0 0 40437 DO3 scaling span -100.0 - +100.0 1000 40438 DO3 proportion cycle 1-120 30 40439 DO3 output limit (lower) 0.0 - 100.0 0 40440 DO3 output limit (upper) 0.0 - 100.0 1000 40441 DO3 limit type 0-3 0 40442 DO4 output type 0: Event output 1: Control output 0 40443 * DO4 master St. No. 0-255 0 40444 DO4 master Ch. No. 1-4 1 40445 * * DO4 BIT position 0-FFFF 8 40446 DO4 output option 0-15 0 40447 DO4 output logic operation AND 0-00FF 0 40449 DO4 output logic operation OR 0-00FF 0 40450 DO4 scaling base -100.0 - +100.0 0 40451 DO4 scaling span -100.0 - +100.0 1000 40452 DO4 proportion cycle 1-120 30 40453 DO4 output limit (lower) 0.0 - 100.0 0 40454 DO4 output limit (upper) 0.0 - 100.0 1000 40455 DO4 limit type 0-3 0 40456 DO5 output type 0: Event output 1: Control output 0 40457 * DO5 master St. No. 0-255 0 40458 DO5 master Ch. No. 1-4 1 40459 * * DO5 BIT position 0-FFFF 16 40460 DO5 output option 0-15 0 40461 DO5 output logic operation AND 0-00FF 0 40463 DO5 output logic operation OR 0-00FF 0 40464 DO5 scaling base -100.0 - +100.0 0 40465 DO5 scaling span -100.0 - +100.0 1000 40466 DO5 proportion cycle 1-120 30 40467 DO5 output limit (lower) 0.0 - 100.0 0 40468 DO5 output limit (upper) 0.0 - 100.0 1000 40469 DO5 limit type 0-3 0 40470 DO6 output type 0: Event output 1: Control output 0 40471 INP-TN5A0202-E * 5-67 5.7 Setting/Monitor Area Entry Numbers (Event I/O module) Contents Reading out/Writing data setting range Factory-set value Register No. Entry ban * * DO6 master St. No. 0-255 0 40472 DO6 master Ch. No. 1-4 1 40473 DO6 BIT position 0-FFFF 0 40474 DO6 output option 0-15 0 40475 DO6 output logic operation AND 0-00FF 0 40477 DO6 output logic operation OR 0-00FF 0 40478 DO6 scaling base -100.0 - +100.0 0 40479 DO6 scaling span -100.0 - +100.0 1000 40480 DO6 proportion cycle 1-120 30 40481 DO6 output limit (lower) 0.0 - 100.0 0 40482 DO6 output limit (upper) 0.0 - 100.0 1000 40483 DO6 limit type 0-3 0 40484 DO7 output type 0: Event output 1: Control output 0 40485 * DO7 master St. No. 0-255 0 40486 DO7 master Ch. No. 1-4 1 40487 * * DO7 BIT position 0-FFFF 0 40488 DO7 output option 0-15 0 40489 DO7 output logic operation AND 0-00FF 0 40491 DO7 output logic operation OR 0-00FF 0 40492 DO7 scaling base -100.0 - +100.0 0 40493 DO7 scaling span -100.0 - +100.0 1000 40494 DO7 proportion cycle 1-120 30 40495 DO7 output limit (lower) 0.0 - 100.0 0 40496 DO7 output limit (upper) 0.0 - 100.0 1000 40497 DO7 limit type 0-3 0 40498 DO8 output type 0: Event output 1: Control output 0 40499 * DO8 master St. No. 0-255 0 40500 DO8 master Ch. No. 1-4 1 40501 * * DO8 BIT position 0-FFFF 0 40502 DO8 output option 0-15 0 40503 DO8 output logic operation AND 0-00FF 0 40505 DO8 output logic operation OR 0-00FF 0 40506 DO8 scaling base -100.0 - +100.0 0 40507 DO8 scaling span -100.0 - +100.0 1000 40508 DO8 proportion cycle 1-120 1 40509 DO8 output limit (lower) 0.0 - 100.0 0 40510 5-68 INP-TN5A0202-E 5.7 Setting/Monitor Area Entry Numbers (Event I/O module) Contents Reading out/Writing data setting range Factory-set value Register No. DO8 output limit (upper) 0.0 - 100.0 1000 40511 DO8 limit type 0-3 0 40512 Entry ban Communication Parameters Contents Reading out/Writing data setting range Factory-set value Register No. Entry ban RS-485 parity setting 0: None 1: Odd 2: Even 0 40111 * RS-485 response interval time 0 to 25 (1digit/20ms) 1 40113 RS-485 communication permission 0: Ready only 1: Read/Write 1 40114 * * RS-485 communication speed 0: 9.6kbps 1: 19.2kbps 2: 38.4kbps 3: Forbidden 4: 115.2kbps 1 40115 * Enhanced communication module (PUMC) connection permission 0 0: PUMC not connected (RS-485 Enable) 1: PUMC connected (RS-485 Disable) 40116 * Configuration Parameters Contents Reading out/Writing data setting range Factory-set Register No. value FAULT output 1 set value 0: HOLD 1: OFF 0 40260 Standby output set value 0000-FFFF 0 40268 Standby mode setting 0: DI=input value DO= Standby output set value 1: DI=All OFF DO=Standby output set value 0 40270 LED2 Lamp configuration 0-2 1 40222 INP-TN5A0202-E Entry ban * 5-69 5.7 Setting/Monitor Area Entry Numbers (Event I/O module) Monitor Parameters Note Monitor parameter can be entered to the monitor area only. Do not enter it to the setting area. Contents Reading out/Writing data setting range Factory-set value Register No. Digital output calculated result monitor 0000 - FFFF - 31002 Digital input calculated result monitor 0000 - FFFF - 31001 Digital input terminal monitor 0000 - FFFF - 31003 Entry ban Internal DO Data Area Contents Reading out/Writing data setting range Factory-set Register No. value 0 41001 0 41002 0 41003 0 41004 Internal DO data area 5 0 41005 Internal DO data area 6 0 41006 Internal DO data area 7 0 41007 Internal DO data area 8 0 41008 Internal DO data area 9 0 41009 Internal DO data area 10 0 41010 Internal DO data area 11 0 41011 Internal DO data area 12 0 41012 Internal DO data area 13 0 41013 Internal DO data area 14 0 41014 Internal DO data area 15 0 41015 Internal DO data area 16 0 41016 Internal DO data area 1 Internal DO data area 2 Internal DO data area 3 Internal DO data area 4 5-70 Event output 1: ON 2: OFF Control output 0.00 to 100.00 Entry ban INP-TN5A0202-E 5.8 Setting/Monitor Area Entry Numbers (Analog module) 5.8 Setting/Monitor Area Entry Numbers (Analog module) The table below shows the register numbers of an analog module, which are settable to each parameter of "Setting/Monitor area entry St. No." and "Setting/Monitor area entry register No." of a programless communication module. Note Parameters marked "*" in the "Entry ban" column in the table can not be changed via programless communication modules. Do not set them to each parameter of "Setting/Monitor area entry St. No." and "Setting/Monitor area entry register No." Operation Parameters Contents Readout/Write data setting range Depends on input range Factoryset value Register Register Register Register No. 1 No. 2 No. 3 No. 4 (Ch1) (Ch2) (Ch3) (Ch4) Entry ban Aio Ai Ao RUN/Standby SW 0: RUN 1: Standby 0 (RUN) 40017 41004 40018 42004 40019 43004 40020 44004 c c c Internal analog output field -327.6 to 327.6% 0 40251 40252 40253 40254 c ¯ c Digital output latch release command 0: OFF 1: Release latch 0 (OFF) 41031 42031 43031 44031 c c ¯ ALM1 set value 1 -100 to 100% FS c 2.5% FS 41033 42033 43033 44033 ALM1 set value 2 -100 to 100% FS c 2.5% FS 41034 42034 43034 44034 ALM2 set value 1 -100 to 100% FS c 2.5% FS 41041 42041 43041 44041 ALM2 set value 2 -100 to 100% FS c 2.5% FS 41042 42042 43042 44042 ALM3 set value 1 -100 to 100% FS c 2.5% FS 41049 42049 43049 44049 ALM3 set value 2 -100 to 100% FS c 2.5% FS 41050 42050 43050 44050 ALM4 set value 1 -100 to 100% FS c 2.5% FS 41057 42057 43057 44057 ALM4 set value 2 -100 to 100% FS c 2.5% FS 41058 42058 43058 44058 ALM5 set value 1 -100 to 100% FS c 2.5% FS 41065 42065 43065 44065 ALM5 set value 2 -100 to 100% FS c 2.5% FS 41066 42066 43066 44066 INP-TN5A0202-E 5-71 5.8 Setting/Monitor Area Entry Numbers (Analog module) Setup Parameters Contents Readout/Write data setting range Depends on input range Factoryset value Register Register Register Register No. 1 No. 2 No. 3 No. 4 (Ch1) (Ch2) (Ch3) (Ch4) Entry ban Aio Ai Ao c c ¯ Analog input type 0: JPt100(0 to 150°C) 1: JPt100(-150 to 600°C) 2: Pt100(0 to 150°C) 3: Pt100(-150 to 300°C) 4: Pt100(-150 to 850°C) 5: J(0 to 400°C) 6: J(0 to 800°C) 7: K(0 to 400°C) 8: K(0 to 800°C) 9: K(0 to 1200°C) 10: R(0 to 1600°C) 11: B(0 to 1800°C) 12: S(0 to 1600°C) 13: T(-199 to 400°C) 14: E(-199 to 800°C) 18: N(0 to 1300°C) 19: PL-2(0 to 1300°C) 21: Voltage (0 to 5V) 22: Voltage (1 to 5V) 23: Voltage (0 to 10V) 24: Voltage (2 to 10V) 7(TC/Pt) 40151 22(VI) 41029 40152 42029 40153 43029 40154 44029 * Analog input scale lower -1999 to 9999 0% FS 41212 42212 43212 44212 * Analog input scale upper -1999 to 9999 100% FS 41213 42213 43213 44213 * Decimal place 0: No decimal point 1: One decimal place 2: Two decimal places 0 (TC/Pt) 1 (VI) 41214 42214 43214 44214 * Temperature unit 0: Degree C 1: Not selectable 0 (°C) 41215 42215 43215 44215 * Analog input shift -10 to 10% FS 0 41216 42216 43216 44216 Analog input filter 0.0 to 120.0sec 2.0 41220 42220 43220 44220 Analog input display zero adjustment -50 to 50% FS c 0 41221 42221 43221 44221 Analog input display span adjustment -50 to 50% FS c 0 41222 42222 43222 44222 Cold junction compensation 0: OFF 1: ON 1 (ON) 41223 42223 43223 44223 5-72 c INP-TN5A0202-E 5.8 Setting/Monitor Area Entry Numbers (Analog module) Contents Readout/Write data setting range Depends on input range Factoryset value Register Register Register Register No. 1 No. 2 No. 3 No. 4 (Ch1) (Ch2) (Ch3) (Ch4) Entry ban Analog output lower -25.0 to 125.0% limit -3.0 41255 42255 43255 44255 Analog output upper limit -25.0 to 125.0% 103.0 41256 42256 43256 44256 Standby analog output set value -3.0 to 103.0% -3.0 41268 42268 43268 44268 Standby mode setting 0: ALM=OFF 1: ALM=ON 0 41270 42270 43270 44270 Linkage operation master St. No. 0 to 255 0 41536 42536 43536 44536 * Linkage operation master Ch. No 1 to 4 Each Ch. 41537 42537 43537 44537 * INP-TN5A0202-E Aio Ai Ao c ¯ c c c ¯ c c c 5-73 5.8 Setting/Monitor Area Entry Numbers (Analog module) System Parameters Contents Readout/Write data setting range Depends on input range Factoryset value Register Register Register Register Entry Aio Ai Ao No. 1 No. 2 No. 3 No. 4 ban (Ch1) (Ch2) (Ch3) (Ch4) Current output range 4: 0 to 20mA 5: 4 to 20mA 5 (4-20mA) 40166 41801 40167 42801 40168 43801 40169 44801 Output type 0: Ai of own station 1: Output 0% 2: Output 0% 3: Output 0% 4: Internal analog output field 5: PV of other St. 6: SV of other St. 7: MV of other St. 3 (output 0%) 40171 41803 40177 42803 40183 43803 40189 44803 Output master St. 0 to 255 stations 0 40172 41804 40178 42804 40184 43804 40190 44804 * Output master Ch. 1 to 4Ch Each Ch. 40173 41805 40179 42805 40185 43805 40191 44805 * Output scaling base -100.0 to 100.0% 0.0 40175 41807 40181 42807 40187 43807 40193 44807 Output scaling span -100.0 to 1000.0 100.0 40174 41806 40180 42806 40186 43806 40192 44806 Output shutdown 0000 to 1111 bit 0 : Output 1 shutdown bit 1 : Output 2 shutdown bit 2 : Output 3 shutdown bit 3 : Output 4 shutdown 0000 DI-1 function select 0: No function 1: RUN/Standby SW 2: No function 3: No function 4: No function 5: No function 6: No function 7: No function 8: No function 9: No function 10: No function 11: No function 12: No function 13: No function 14: No function 15: No function 16: No function 17: Latch release (all) 18: Latch release (DO1) 19: Latch release (DO2) 20: Latch release (DO3) 21: Latch release (DO4) 22: Latch release (DO5) 23: No function 0 5-74 c ¯ c 40201 41013 42013 43013 44013 c c c INP-TN5A0202-E 5.8 Setting/Monitor Area Entry Numbers (Analog module) Contents Readout/Write data setting range Depends on input range Factoryset value Register Register Register Register Entry Aio Ai Ao No. 1 No. 2 No. 3 No. 4 ban (Ch1) (Ch2) (Ch3) (Ch4) DI-1 function select 24: No function 25: No function 26: Start timer(DO1) 27: Start timer(DO2) 28: Start timer(DO3) 29: Start timer(DO4) 30: Start timer(DO5) 31: No function 32: No function 33: No function 34: No function 35: No function 36: No function 37: No function 38: No function 39: No function 40: No function 41: No function 42: No function 43: No function 44: No function 45: No function 46: No function 47: No function 48: No function 49: Output 1 shutdown 50: Output 2 shutdown 51: Output 3 shutdown 52: Output 4 shutdown 0 41013 42013 43013 44013 DI-2 function select 0 to 52 0 41014 42014 43014 44014 DI-3 function select 0 to 52 0 41015 42015 43015 44015 DI-4 function select 0 to 52 0 41016 42016 43016 44016 DI-5 function select 0 to 52 0 41017 42017 43017 44017 DI-6 function select 0 to 52 0 41018 42018 43018 44018 DI-7 function select 0 to 52 0 41019 42019 43019 44019 DI-8 function select 0 to 52 0 41020 42020 43020 44020 DI-9 function select 0 to 52 0 41021 42021 43021 44021 DI-10 function select 0 to 52 0 41022 42022 43022 44022 DI-11 function select 0 to 52 0 41023 42023 43023 44023 DI-12 function select 0 to 52 0 41024 42024 43024 44024 DI-13 function select 0 to 52 0 41025 42025 43025 44025 DI-14 function select 0 to 52 0 41026 42026 43026 44026 DI-15 function select 0 to 52 0 41027 42027 43027 44027 DI-16 function select 0 to 52 0 41028 42028 43028 44028 DI master St. setting 0 41011 42011 43011 44011 INP-TN5A0202-E 0 to 255 c c c * 5-75 5.8 Setting/Monitor Area Entry Numbers (Analog module) Contents Readout/Write data setting range Depends on input range Factoryset value Register Register Register Register Entry Aio Ai Ao No. 1 No. 2 No. 3 No. 4 ban (Ch1) (Ch2) (Ch3) (Ch4) DO 1 output event type setting 0-102 0 41032 42032 43032 44032 DO1 option function setting 0000 to 1111 bit 0 : Alarm latch function bit 1 : Error input alarm function bit 2 : Non-excitation output function bit 3 : Hold reset function 0000 41036 42036 43036 44036 DO2 output event type setting 0-102 0 41040 42040 43040 44040 DO2 option function setting 0000 to 1111 bit 0 : Alarm latch function bit 1 : Error input alarm function bit 2 : Non-excitation output function bit 3 : Hold reset function 0000 41044 42044 43044 44044 DO3 output event type setting 0-102 0 41048 42048 43048 44048 DO3 option function setting 0000 to 1111 bit 0 : Alarm latch function bit 1 : Error input alarm function bit 2 : Non-excitation output function bit 3 : Hold reset function 0000 41052 42052 43052 44052 DO4 output event type setting 0-102 0 41056 42056 43056 44056 DO4 option function setting 0000 to 1111 bit 0 : Alarm latch function bit 1 : Error input alarm function bit 2 : Non-excitation output function bit 3 : Hold reset function 0000 41060 42060 43060 44060 DO5 output event type setting 0-102 0 41064 42064 43064 44064 DO5 option function setting 0000 to 1111 bit 0 : Alarm latch function bit 1 : Error input alarm function bit 2 : Non-excitation output function bit 3 : Hold reset function 0000 41068 42068 43068 44068 Mode at startup 0: Auto mode 1: Standby 2: Standby 3: Standby 0 (Auto) 41304 42304 43304 44304 5-76 * c c ¯ * * * * * c c c INP-TN5A0202-E 5.8 Setting/Monitor Area Entry Numbers (Analog module) Alarm Parameter Contents Readout/Write data setting range ALM1 hysteresis 0 to 50% FS ALM1 delay time Depends on input range Factoryset value Register Register Register Register No. 1 No. 2 No. 3 No. 4 (Ch1) (Ch2) (Ch3) (Ch4) 0.25% FS 41035 42035 43035 44035 0 to 99 min. 59sec. /0 to 99hr. 59min. 0 41037 42037 43037 44037 ALM1 delay time units 0: sec. 1: min. 0 (Second) 41038 42038 43038 44038 ALM2 hysteresis 0 to 50% FS 0.25% FS 41043 42043 43043 44043 ALM2 delay time 0 to 99 min. 59sec. /0 to 99hr. 59min. 0 41045 42045 43045 44045 ALM2 delay time units 0: sec. 1: min. 0 (Second) 41046 42046 43046 44046 ALM3 hysteresis 0 to 50% FS 0.25% FS 41051 42051 43051 44051 ALM3 delay time 0 to 99 min. 59sec. /0 to 99hr. 59min. 0 41053 42053 43053 44053 ALM3 delay time units 0: sec. 1: min. 0 (Second) 41054 42054 43054 44054 ALM4 hysteresis 0 to 50% FS 0.25% FS 41059 42059 43059 44059 ALM4 delay time 0 to 99 min. 59sec. /0 to 99hr. 59min. 0 41061 42061 43061 44061 ALM4 delay time units 0: sec. 1: min. 0 (Second) 41062 42062 43062 44062 ALM5 hysteresis 0 to 50% FS 0.25% FS 41067 42067 43067 44067 ALM5 delay time 0 to 99 min. 59sec. /0 to 99hr. 59min. 0 41069 42069 43069 44069 ALM5 delay time units 0: sec. 1: min. 0 (Second) 41070 42070 43070 44070 Object Ch. No. for interchannel ALM1 1 to 4 1 41039 42039 43039 44039 Object Ch. No. for interchannel ALM2 1 to 4 1 41047 42047 43047 44047 Object Ch. No. for interchannel ALM3 1 to 4 1 41055 42055 43055 44055 Object Ch. No. for interchannel ALM4 1 to 4 1 41063 42063 43063 44063 Object Ch. No. for interchannel ALM5 1 to 4 1 41071 42071 43071 44071 INP-TN5A0202-E c c c c c Entry ban Aio Ai Ao c c ¯ 5-77 5.8 Setting/Monitor Area Entry Numbers (Analog module) Communication Parameters Contents Readout/Write data setting range Depends Register Register Register Register Factory-set on input No. 1 No. 2 No. 3 No. 4 value range (Ch1) (Ch2) (Ch3) (Ch4) Entry ban Aio Ai Ao c c c RS-485 Parity setting 0: None 1: ODD 2: EVEN 0 40111 * RS-485 Communication speed 0: 9.6kbps 1: 19.2kbps 2: 38.4kbps 3: Forbidden 4: 115.2kbps 1 40115 * RS-485 Communication permission 0: Read only 1: Read/Write 1 (R/W) 40114 * RS-485 Response interval time 0-25 (20ms/1digit) 0 40113 * Enhanced communication module (PUMC) connection permission 0: PUMC not connected (RS-485 Enable) 1: PUMC connected (RS-485 Disable) 0 (RS-485 Enable) 40116 * Master/slave setting 0: Master 1: Slave in connected modules 1 (Slave) 40117 * User address 01 30000 to 49999 30002(Ai1) 40301 * User address 02 30000 to 49999 30002(Ai1) 40302 * User address 03 30000 to 49999 30002(Ai1) 40303 * User address 04 30000 to 49999 30002(Ai1) 40304 * User address 05 30000 to 49999 30002(Ai1) 40305 * User address 06 30000 to 49999 30002(Ai1) 40306 * User address 07 30000 to 49999 30002(Ai1) 40307 * User address 08 30000 to 49999 30002(Ai1) 40308 * User address 09 30000 to 49999 30002(Ai1) 40309 * User address 10 30000 to 49999 30002(Ai1) 40310 * User address 11 30000 to 49999 30002(Ai1) 40311 * User address 12 30000 to 49999 30002(Ai1) 40312 * User address 13 30000 to 49999 30002(Ai1) 40313 * User address 14 30000 to 49999 30002(Ai1) 40314 * User address 15 30000 to 49999 30002(Ai1) 40315 * User address 16 30000 to 49999 30002(Ai1) 40316 * User address 17 30000 to 49999 30002(Ai1) 40317 * User address 18 30000 to 49999 30002(Ai1) 40318 * User address 19 30000 to 49999 30002(Ai1) 40319 * 5-78 INP-TN5A0202-E 5.8 Setting/Monitor Area Entry Numbers (Analog module) Contents Readout/Write data setting range Depends Register Register Register Register Factory-set on input No. 1 No. 2 No. 3 No. 4 value range (Ch1) (Ch2) (Ch3) (Ch4) Entry ban Aio Ai Ao c c c User address 20 30000 to 49999 30002(Ai1) 40320 * User address 21 30000 to 49999 30002(Ai1) 40321 * User address 22 30000 to 49999 30002(Ai1) 40322 * User address 23 30000 to 49999 30002(Ai1) 40323 * User address 24 30000 to 49999 30002(Ai1) 40324 * User address 25 30000 to 49999 30002(Ai1) 40325 * User address 26 30000 to 49999 30002(Ai1) 40326 * User address 27 30000 to 49999 30002(Ai1) 40327 * User address 28 30000 to 49999 30002(Ai1) 40328 * User address 29 30000 to 49999 30002(Ai1) 40329 * User address 30 30000 to 49999 30002(Ai1) 40330 * User address 31 30000 to 49999 30002(Ai1) 40331 * User address 32 30000 to 49999 30002(Ai1) 40332 * User data 01 Depends on "User address 01" - 45001 * User data 02 Depends on "User address 02" - 45002 * User data 03 Depends on "User address 03" - 45003 * User data 04 Depends on "User address 04" - 45004 * User data 05 Depends on "User address 05" - 45005 * User data 06 Depends on "User address 06" - 45006 * User data 07 Depends on "User address 07" - 45007 * User data 08 Depends on "User address 08" - 45008 * User data 09 Depends on "User address 09" - 45009 * User data 10 Depends on "User address 10" - 45010 * User data 11 Depends on "User address 11" - 45011 * User data 12 Depends on "User address 12" - 45012 * User data 13 Depends on "User address 13" - 45013 * User data 14 Depends on "User address 14" - 45014 * INP-TN5A0202-E 5-79 5.8 Setting/Monitor Area Entry Numbers (Analog module) Contents Readout/Write data setting range Depends Register Register Register Register Factory-set on input No. 1 No. 2 No. 3 No. 4 value range (Ch1) (Ch2) (Ch3) (Ch4) Entry ban Aio Ai Ao c c c User data 15 Depends on "User address 15" - 45015 * User data 16 Depends on "User address 16" - 45016 * User data 17 Depends on "User address 17" - 45017 * User data 18 Depends on "User address 18" - 45018 * User data 19 Depends on "User address 19" - 45019 * User data 20 Depends on "User address 20" - 45020 * User data 21 Depends on "User address 21" - 45021 * User data 22 Depends on "User address 22" - 45022 * User data 23 Depends on "User address 23" - 45023 * User data 24 Depends on "User address 24" - 45024 * User data 25 Depends on "User address 25" - 45025 * User data 26 Depends on "User address 26" - 45026 * User data 27 Depends on "User address 27" - 45027 * User data 28 Depends on "User address 28" - 45028 * User data 29 Depends on "User address 29" - 45029 * User data 30 Depends on "User address 30" - 45030 * User data 31 Depends on "User address 31" - 45031 * User data 32 Depends on "User address 32" - 45032 * 5-80 INP-TN5A0202-E 5.8 Setting/Monitor Area Entry Numbers (Analog module) Configuration Parameters Contents Readout/Write data setting range Depends on input range Factoryset value Register Register Register Register No. 1 No. 2 No. 3 No. 4 (Ch1) (Ch2) (Ch3) (Ch4) Entry ban Aio Ai Ao c c c LED2 lamp allocation 0 to 255 1 40222 * LED3 lamp allocation 0 to 255 12 40223 * LED4 lamp allocation 0 to 255 13 40224 * LED5 lamp allocation 0 to 255 14 40225 * LED6 lamp allocation 0 to 255 15 40226 * Reset main unit 0: Do nothing 1: Reset main unit 0 40101 * Monitor Parameters Note Monitor parameters can enter for the monitor area only. Do not enter the setting area. Contents Readout/Write data setting range Depends Factory- Register Register Register Register on input set No. 1 No. 2 No. 3 No. 4 range value (Ch1) (Ch2) (Ch3) (Ch4) System time 0 to 65535 - Input value (Analog input) -5 to 105% FS - 30002 31001 30003 32001 30004 33001 30005 34001 RCJtemp -3276.7 to 3276.7°C - 30110 31016 30111 32016 30112 33016 30113 34016 Error source display 0 to FFFF - 31008 32008 33008 34008 Alarm 1-5 status 0 to 001F - 31007 32007 33007 34007 Event input status 0 to FFFF - 31061 32061 33061 34061 Remaining time on timer 1 0 to 99 min. 59 sec. /0 to 99hr. 59 min. - 31011 32011 33011 34011 Remaining time on timer 2 0 to 99 min. 59 sec. /0 to 99hr. 59 min. - 31012 32012 33012 34012 Remaining time on timer 3 0 to 99 min. 59 sec. /0 to 99hr. 59 min. - 31013 32013 33013 34013 Remaining time on timer 4 0 to 99 min. 59 sec. /0 to 99hr. 59 min. - 31014 32014 33014 34014 Remaining time on timer 5 0 to 99 min. 59 sec. /0 to 99hr. 59 min. - 31015 32015 33015 34015 Output value (Analog outout) -3.0 to 103.0% - 30120 30121 30122 30123 RS-485 Communication 0: Read only permission 1: Read/Write INP-TN5A0202-E - 30001 30062 Entry ban Aio Ai Ao c c ¯ c ¯ c c c c 5-81 5.8 Setting/Monitor Area Entry Numbers (Analog module) 5-82 INP-TN5A0202-E 1 Overview 2 System Configuration Example 6 Loader Communications Loader Communication Functions …… 6-3 6.2 Loader Communication Specifications 6.3 Loader Connection ……………………… 6-5 6.4 Setting Loader Communication Parameters … 6-6 6.5 MODBUS Communication Protocol …… 6-7 6.6 Command and Transmission Frame Details … 6-15 3 Installation 6.1 6-4 4 Programless Communication Operation 5 System Configuration 6 Loader Communications 7 Trouble Shooting INP-TN5A0202-E 6-1 6.1 Loader Communication Functions 6-2 INP-TN5A0202-E 6.1 Loader Communication Functions 6.1 Loader Communication Functions The equipment equipped with communication functions via the loader interface, which enables data exchange to such devices as PC. The communication system composed of the one to one communication between a master (such as, personal computer) and a slave (the equipment). Note ● The system constructed with the equipment as slaves do not respond to messages issued by the master with broadcast queries are where the station number is “0”. ● Communications with a loader interface should not be performed during production operation. ● The equipment can not perform communication to a programless communication module with it connected to a loader port on the control module. The sending/receiving data format should be same to perform communication between a master and a slave. The communication data format by the MODBUS protocol is explained in this manual. When performing the loader communication, connect an optional loader connecting cable (RS-232C, Type: PUMZ*L01) to the front face loader communication port of the main unit in order to perform RS-232 communication to the personal computer. Connection with PC Personal Computer RS-232C PUM series INP-TN5A0202-E 6-3 6.2 Loader Communication Specifications 6.2 Loader Communication Specifications Loader interface Item Specifications Electrical specifications EIA RS232C Transmission method 3-wire system, half duplex serial Synchronous method Asynchronous Connection mode 1:1 Station number 128 Communication speed 19.2kbps (fixed) Data format Data length 8 bits Stop bit 1 bits Parity None (fixed) Transmission code HEX value (MODBUS RTU mode) Error detection CRC-16 Insulation No insulation with the internal circuit 6-4 INP-TN5A0202-E 6.3 Loader Connection 6.3 Loader Connection Warning DO NOT TURN THE POWER ON UNTIL ALL OF THE WIRING IS COMPLETED. THERE IS A RISK OF ELECTRICAL SHOCK OR DAMAGE. Communication terminal Loader communication port Loader connecting cable PWR PUM-C BUS LOADER RX1 TX1 STATION $%& ( ' # TX2 RX2 Connection with a loader communication port • Use an optional loader connecting cable (RS-232C). Loader connecting cable (RS-232C) PUMZ*L01 Master RS-232C PC etc. PWR PUM-C BUS LOADER RX1 TX1 # $%& ' TX2 ( STATION RX2 D-Sub 9-pin INP-TN5A0202-E 6-5 6.4 Setting Loader Communication Parameters 6.4 Setting Loader Communication Parameters In order to perform communication between the master and the equipment properly, the setting below is necessary. • All communication conditions settings for both of the master and the equipment should be the same. Setting items for loader interface (The equipment) Items Setting range Factory-set value The value is fixed regardless of the setting of St. No. configuration SW. Station No. 128 Communication speed setting 19.2kbps (Fixed) ― Not changeable Data length 8 bits ― Not changeable Parity None ― Not changeable 6-6 128 Remarks column INP-TN5A0202-E 6.5 MODBUS Communication Protocol 6.5 MODBUS Communication Protocol The communication system with MODBUS protocol always performs communication by using the procedure that “the master sends a command message first, and the applicable slave sends a response message back”. Communication procedure is shown in the flow chart below. The master sends a command message to the slave. The slave checks if the station number in the received message is the same as its own number. When it is the same The slave runs a command, and sends the response message INP-TN5A0202-E When it is not the same The slave throws out the message received, and waits for the next message (No reply) 6-7 6.5 MODBUS Communication Protocol When the station number in the command massage received is the same as its own number. Master Slave Command message When the station No. is the same Response message When the station number in the command message received is not the same as its own number. Master Slave Command message When the station No. is not the same 6-8 INP-TN5A0202-E 6.5 MODBUS Communication Protocol Message composition Command messages are composed of four parts; a station number, a function code, a data part, and an error check code, and sent them in the order above. Field Name Number of Bytes Station No. 1 byte Function code 1 byte Data part 2 to 64 bytes Error check code (CRC-16) 2 bytes Station No. This is the number allocated to a slave. It is fixed to “128”. Function code This code specifies the function for the slave to perform. Data part These data is required to run the function code. The composition of the data part varies according to function codes. Coil number or register number is allocated to the data in the temperature controller, and specify those numbers to read out/write through communications. The coil number or the register number in messages uses relative addresses. The relative address is calculated using the formula below. Relative address = (The last 4 digits of a coil No. / register No.) -1 Ex.) When a function code specifies a register number “40003” Relative address = (The last 4 digits of 40003) – 1 = 0002 is used in the message. Error check code This code is for detecting the message error (changes in the bits) during the signal transmission process. MODBUS protocol mode (RTU mode) uses CRC-16 (Cyclic Redundancy Check). INP-TN5A0202-E 6-9 6.5 MODBUS Communication Protocol Slave response • Normal slave response A slave creates and replies the response message to each command message. The slave response message uses the same format as the command message. Contents inside the data part vary according to function codes. • Irregular slave response If there are problems (such as specification of a nonexistent function code) with the contents of command messages other than transmission error, a slave creates and sends back an error response message without running the command. The composition of an error response message is as follows. The function code uses the value that the function code of the command message plus 80H. Field Name Number of Bytes Station No. 1 byte Function Code + 80H 1 byte Error Code 1 byte Error Check Code (CRC-16) 2 bytes The error codes are shown below. Error Code Contents Explanation 01H Function code failure A nonexistent function code was specified. Check the function code. 02H Address failure for coil/register The specified relative address for the coil No. /the register No. cannot be used by the specified function code. 03H Coil/register/limit failure The specified number of words is too many and specifies the range that does not contain the coil No./register No. The specified data is specified beyond the limit. 06H Busy state Data is been writing in the register. Retrying communication after more than 100- sec interval. • No slave response In the following cases, a slave ignores the command message, and send the response message back neither. • In the case that the station number specified by the command message is not the same as the station number specified for a slave. • In the case that the error check code does not correspond or the transmission error (such as parity error) is detected. • In the case that the interval between the message composing data is 24 bit time or more. 6-10 INP-TN5A0202-E 6.5 MODBUS Communication Protocol Function code With MODBUS protocol, the different coil number/register number is allocated depends on the function code, and each function code is only available for a certain coil number/register number. The diagram below is shown the correspondence between the function code and the coil number/register number. Function code Code Coil / Register No. Function Target No. Contents 03H Read out (continuous) Hold register 3xxxx Read out word data 04H Read out (continuous) Input register 4xxxx Read out/Write word data 06H Write Hold register 10H Write (continuous) Hold register The message length on the each function is shown below. Code Contents Number of allocatable data Command message Response message Minimum Maximum Minimum Maximum 03H Read word data 125 words* 8 bytes 8 bytes 7 bytes 69 bytes 04H Read out word data (Read out only) 125 words* 8 bytes 8 bytes 7 bytes 69 bytes 06H Write word data 1 word 8 bytes 8 bytes 8 bytes 8 bytes 10H Write series of word data 123 words* 11 bytes 73 bytes 8 bytes 8 bytes *: “Number of allocatable data” above is limited by the number of data that the equipment allocates for the coil/address number. (Excluding the function code 06H) INP-TN5A0202-E 6-11 6.5 MODBUS Communication Protocol Error Check Code (CRC-16) Calculation CRC-16 is 2-byte (16-bit) error check code. The calculating range is the starting position of the message (station number) to the end of the data part. A slave calculates the CRC of the message received, and does not send the response message back, if the result is not the same as the CRC code received. The flow for CRC-16 calculation is as below. Start Set FFFFH (hexadecimal) to CR Set J=1 Variables CR: CRC error check data (2 bytes) J: command message calculation character digit K: The number of times to check CR calculation Exclusive OR (XDR) is run on each character of J (1 byte) an in specified message and CR, and that result is set to CR. Set K=1 Is the bit at the right end of the CR 1? NO YES After CR has been justified 1 bit to right, A001H and exclusive OR (XDR) are run, and that result is set to CR. Justify CR 1 bit to right Add 1 to K NO Have 8-time calculations completed? YES Add 1 to J NO Has the all characters’ calculation complete? YES Completed 6-12 (Calculate in order of command message station No., function code and data.) CR calculation result is added to at the end of command message in order of LOW, HIGH. INP-TN5A0202-E 6.5 MODBUS Communication Protocol Transmission control procedure Master communication method Master should start communication following the rules below. 1. Provide more than 48-bit time blank state before sending the command message. 2. The interval between the sent messages should be less than 24 bit times. 3. The master will be in the receiving standby mode within 24 bit time after sending the command message. 4. Provide blank state more than 48 bit time prior to sending the next message after receiving the response message. (the same as the 1st rule) 5. For safety, create the framework where the master checks the response message, and if there is no response or errors occur, retry at least 3 times. Note The definition above is the minimum required value. For safety, creating the master side program with providing margins 2 to 3 times as large is recommended. For a concrete example, creating the blank state (the 1st rule above) more than 10ms, the interval between bytes (the 2nd rule above) and switching from sending to receiving (the 3rd rule) within 1ms for 19.2kbps is recommended. Frame detection There are 2 states with the circuit as below. • Blank state (no data on the circuit) • Communication state (data running on the circuit) The equipment connected on the circuit is in the receiving state first and monitors the circuit. When the blank state more than 24 bit time appears, it detects the end of the previous frame and will be in the receiving standby mode within the next 24 bit time. When data appears on the circuit, it begins receiving and when the blank state more than 24 bit appears again, it detects the end of the frame. In other words, the data appears on the circuit during appearance of the first blank state more than 24 bit time to the next blank state more than 24 bit time is loaded as one frame (a bundle of data). Therefore, one frame should be sent following the rules below. • Provide the blank state more than 48 bit time before sending the command message. • The interval between bytes of the message sent should be less than 24 bit time. INP-TN5A0202-E 6-13 6.5 MODBUS Communication Protocol The equipment response The equipment, after detected the frame (detection of the blank state more than 24 bit time), runs that frame as the command message. In the case the frame message is for the own station, the equipment send the response message back; it takes about 1 to 30 ms for this operation. (How long it takes is depends on the contents of the command message.) Therefore, the master, after sending the command message, should follow the rules shown below • After sending the command message, the master will be in the receiving standby mode within 24 bit time. Master Slave POL1 1 to 30 mms More than 5ms interval Is necessary (More than 10ms is recommended) POL1 response data POL2 1 to 30 mms POL2 response data 6-14 INP-TN5A0202-E 6.6 Command and Transmission Frame Details 6.6 Command and Transmission Frame Details Reading Data Reading Word Data (Function Code: 03H) The unit reads word data continuously for the specified number of words from the first number to start reading from. The slave forwards the read word data from the upper number of bytes to the lower number. Note ● When reading out word data continuously, specification beyond the range of the relative address will result in no response. ● Do not write data to the number not listed on the MODBUS register numbers. (It might cause the equipment's abnormal operation.) Function code 03H Number of readable words in one message 125 INP-TN5A0202-E 6-15 6.6 Command and Transmission Frame Details • Message composition Master Slave Command composition (Byte) Response message composition (Byte) Station No. Station No. Function code Function code Number to start reading Upper out (Relative address) Lower Number of bytes to read out (Number of words to read out ×2) Upper Number of words to read out (1 to 32 words) Lower First word data contents Upper Lower Next word data contents Upper Last word data contents Upper CRC data Upper CRC data The meaning of read out word MSB Lower Lower Lower Lower Upper LSB First word data contents upper byte First word data contents lower byte Next word data contents upper byte Next word data contents lower byte Last word data contents upper byte Last word data contents lower byte 6-16 INP-TN5A0202-E 6.6 Command and Transmission Frame Details • Example of message transmission When reading out the set value of “Device Type of Setting Area” from a programless communication module, the message composition is as follows. • “Device type of the setting area” relative address: 000Ah Master Slave Command message (Byte) Station No. 80H Function code Response Message (Byte) 03H Station No. 80H Number to start reading out (Relative address) Upper 00H Function code 03H Lower 0AH Number of bytes to read out 02H Number of words to read out Upper 00H Lower 01H First word data contents Lower BAH Upper 19H CRC data CRC data Upper 00H Lower A8H Lower 85H Upper E4H The meaning of read out data Device type of the setting area= 00A8h (Data register) INP-TN5A0202-E 6-17 6.6 Command and Transmission Frame Details Reading out read-only word data (Function code: 04H) The equipment reads out the word data specified by the number of words to read out continuously from the number to start reading out. A slave sends the read out data in order of the upper bytes, the lower bytes. Function code 04H Max. number of readable words in one message 125 Relative address 0000H to OFDCH Register No. 30001 to 34061 • Message composition Master Slave Command composition (Byte) Response message composition (Byte) Station No. Station No. Function code Function code Number to start reading Upper out (Relative address) Lower Number of bytes to read out (Number of word to read out ×2) Upper Number of words to read out (1 to 15 words) Lower First word data contents Upper Lower Next word data contents Upper Last word data contents Upper CRC data Upper CRC data The meaning of reading out word data MSB Lower Lower Lower Lower Upper LSB First word data contents upper byte First word data contents lower byte Next word data contents upper byte Next word data contents lower byte Last word data contents upper byte Last word data contents lower byte 6-18 INP-TN5A0202-E 6.6 Command and Transmission Frame Details • Example of message transmission When reading out “PLC inter-cycle time monitor” from the programless communication module, the message composition is as follows. • “PLC inter-cycle time monitor” relative address: 03EEh Master Slave Command message (Byte) Station No. 80H Function code Response message (Byte) 04H Station No. 80H Number to start reading out (Relative address) Upper 03H Function code 04H Lower EEH Number of bytes to read out 02H Number of words to read out Upper 00H Lower 01H First word data contents CRC data Lower 4FH Upper AAH CRC data Upper 00H Lower 32H Lower 04H Upper FBH The meaning of read out data PLC inter-cycle time monitor = 50ms INP-TN5A0202-E 6-19 6.6 Command and Transmission Frame Details Writing Data Writing word Data (1 word, function code: 06H) This writes the specified data to the specified number for word data. The master sends the data to be written from the upper number of bytes to the lower number. Function code 06H Max. number of readable words in one message 1 • Message composition Master Slave Command message composition (Byte) Station No. Response message composition (Byte) Function code Number to specify writing (Relative address) Write word data CRC data 6-20 Station No. Upper Function code Lower Number to specify writing (Relative address) Upper Lower Lower Upper Write word data CRC data Upper Lower Upper Lower Lower Upper INP-TN5A0202-E 6.6 Command and Transmission Frame Details • Example of message transmission This example shows when setting “Setting Area Device Size” for the programless communication module to 500 (01F4h). • “Setting Area Device Size” relative address: 000Dh Master Slave Command message (Byte) Station No. 80H Function code Number to specify writing (Relative address) Write word data CRC data INP-TN5A0202-E Response message (Byte) 06H Station No. 80H Upper 00H Function code 06H Lower 0DH Number to specify writing (Relative address) Upper 01H Lower F4H Lower 06H Upper 0FH Write word data CRC data Upper 00H Lower 0DH Upper 01H Lower F4H Lower 06H Upper 0FH 6-21 6.6 Command and Transmission Frame Details Write series of words (Function code: 10H) Write how long it takes to write words and the series of word information beginning from the start writing number. The master sent the writing word data in order of the upper, the lower. Function code 10H Max. number of readable words in one message 123 • Message composition Master Slave Command message composition (Byte) Station No. Function code Number to start write (Relative address) Number of word to write Response message composition (Byte) Upper Station No. Lower Function code Upper Lower Number of byte to write First write word data Next write word data Last write word data CRC data } } 1 to 32 Number to start write (Relative address) Upper Number of word to write ×2 Number of word to write Upper Upper CRC data Lower Lower Lower Lower Upper Upper Lower Upper Lower Lower Upper Meaning of write word data MSB LSB First word data contents upper byte First word data contents lower byte Next word data contents upper byte Next word data contents lower byte Last word data contents upper byte Last word data contents lower byte 6-22 INP-TN5A0202-E 6.6 Command and Transmission Frame Details • Example of message transmission This example shows when setting 1000 (03E8h) to "Setting Area Start Address (Lower, Upper)" of the programless communication module. • Setting area start address (Lower) = 1000 (=03EBh) • Setting area start address (Upper) = 0 (=0000h) • “Setting area start address (Lower)” relative address: 000Ch Master Slave Command message composition (Byte) Station No. 80H Response message composition (Byte) Function code 10H Station No. 80H 00H Function code 10H Number to specify writing (Relative address) Write word data Upper Lower 0BH Upper 00H Lower Number of byte to write First write word data Last write word data CRC data INP-TN5A0202-E 02H 04H Upper 03H Lower E8H Upper 00H Lower 00H Lower 9FH Upper 52H Number to specify writing (Relative address) Number of word to write CRC data Upper 00H Lower 0BH Upper 00H Lower 02H Lower 2EH Upper 1BH 6-23 6.6 Command and Transmission Frame Details 6-24 INP-TN5A0202-E 1 Overview 2 System Configuration Example 3 Installation Error Procedure …………………………… 7-3 7.1 4 Programless Communication Operation 5 System Configuration 6 Loader Communications 7 Trouble Shooting 7-1 INP-TN5A0202-E Trouble Shooting 7 7.1 Error procedure 7-2 INP-TN5A0202-E 7.1 Error procedure 7.1 Error Procedure Troubles during operation If troubles occur during operation, check the type of your module, its connection and parameter setting for any abnormalities. Refer to the user’s manual for MELSEC-Q/A/AnS/FX series about PLC. The dialog below shows the typical troubles and the solutions on their problems. Troubles PWR indicator: No light (even if turning the power ON) Causes Solutions No power supply with the main unit Check the power supply wiring is installed Supply voltage is out of the allowable range Use the power supply conforming to the main unit specifications Main unit failure Replace the module. The power of PLC is OFF Turn on PLC Connection failure Check the RS-232C/RS-422/RS-485 connection between the DIP SW 1 (selection of RS-232C/RS-422/RS-485) of programless communication module and the communication unit of PLC Check the signal conductor between the programless communication module and the PLC Check the connection of the connecting cable PWR indicator: RED light Connecting cable failure Check the connecting cable break Check the signal conductor wiring of the connecting cable St. No. setting error of PLC communication unit Set "0" to the St. No. of PLC Check PLC communication speed Communication setting of communication speed/communication data length is mismatch with PLC INP-TN5A0202-E setting 5-11 / PLC transmission of the programless setting 5-12 communication module matches the communication setting of PLC 7-3 7.1 Error procedure Troubles Causes Response monitoring time of a programless communication module is short (Timeout occurs between PLC and a programless communication module) PWR indicator: RED light PWR indicator: RED blinking (irregular) Data in the all modules can not be readout (Even if set the Reading demand flag and Parameter setting demand flag for PLC setting area, data cannot be readout) 7-4 Set longer PLC response monitoring time of a programless 5-15 communication module Capacity of the file register has not been set for the PLC parameter setting by using the file register (R or ZR) for the device type in the Setting/Monitor area of a programless communication module The file register capacity setting is necessary by the PLC parameter setting. Set the file register capacity and check the operation MELSEC-A series being used and the check of RS-232C CD terminal is enable Make the CD terminal disable by ladder program MELSEC-FX series being used and type 2 is set for MC protocol of the programless communication module's parameter or "0" is set for MC protocol frame type Set type 4 for MC protocol and "1" for MC protocol frame type with PUM parameter loader, and then restart St. Nos of a programless communication module are duplicated, even during 1:N connection Set St. Nos of the programless communication module not to be duplicated The parameter value registered for the programless communication module is invalid value PWR indicator: RED blinking (0.4-sec inter-cycle) Solutions Check the error code of Setting error , write the correct parameter 5-18 set value on the PUM parameter loader, and then restart Check the error code of Setting error SW setting is invalid value , modify it to the correct 5-18 setting, and then restart The combination of parameter's content and the SW setting set to the programless communication module is not correct. Check the error code of Setting error Response monitoring time of a programless communication module is short (Timeout sometimes occurs between PLC and a programless communication module) Set longer PLC response monitoring time of a programless communication Programless communication is in a rest state (Command setting response flag "EEEEh" or "FFFFh") Demand the communication restoration by using the Command setting demand flag in the PLC setting area Inter-module connection failure Check the inter-module connection The unit failure Replace the module , modify it to the correct SW 5-18 setting/modify it to the correct set value on PUM parameter loader, and then restart module, or increase Number of retry times 5-15 INP-TN5A0202-E 7.1 Error procedure Troubles Only certain connected modules cannot be read out data Causes Solutions The applicable module is accessing to non-supported MODBUS address Check the MODBUS address supported by the applicable module Access beyond the applicable module device number (Device size over) Modify the parameter setting within the applicable device size Incorrect St. No. setting of the applicable module Set the applicable module station number correctly The unit failure Replace the applicable module PWR indicator shows the red light: Short PLC response monitoring time Set longer PLC response monitoring time, or increase Number of retry times 5-15 Modify the setting no to duplicate the device Duplication of PLC device memory types and the start address of the Setting/ Monitor area Wrong data value read out to PLC device Monitor area response flag (in the 8000hs): Abnormal response status 5-5, 5-8 Device memory is overwritten on the PLC sequence program Check the device used on the PLC sequence program, modify the setting not to overwrite the device memory (Check the duplicating part using the device list for use etc. by PLC GX Developer) Duplication of the monitor area device memory setting of PLC with 1: N connection Make the monitor area device memory setting of each programless communication module not to be duplicated Invalid value was written to the control/event module Check and modify the value set to the data field for the setting area The power of PLC is OFF Turn on PLC Connection failure Check the RS-232C/RS-422/RS-485 connection between the DIP SW 1, SW2 (selection of RS-232C/RS-422/RS-485) of programless communication module and the PLC Check the signal conductor between the programless communication module and the PLC PWR indicator: GREEN blinking during 1:N connection (0.1-sec inter-cycle) Connecting cable failure Check the signal conductor state between a programless communication module and PLC, and also check the connecting cable break Check if the signal conductor between a programless communication module and PLC is correct INP-TN5A0202-E 7-5 7.1 Error procedure Troubles Causes Solutions PLC communication speed and PLC communication data length is mismatch Check PLC communication speed setting/ PLC data length setting of the programless communication module matches the communication setting of PLC The master station (St. No. "0") for 1:N connection is not connected Connect the programless communication module which St. No. is "0" Only some programless communication modules which are connected during 1:N connection cannot perform a programless communication There are some programless communication modules that settings below differ • PLC communication speed • PLC communication data length • MC protocol • PLC communication inter-cycle time • PLC response monitoring time • Connection method • No. of connected units • MC protocol frame type Correct the set value with PUM parameter loader and restart Written value to PLC device is sent to several programless communication modules With 1:N connection, the setting area device memory setting of PLC is duplicated Make the setting area device memory setting of each programless communication module not to be duplicated The value of Inter-PLC communication execution time monitor came to be extremely big during 1:N connection Other connected programless communication modules were in the communication error state (ex. break) Restore the programless communication module that is in the communication error state, and restart PWR indicator: GREEN blinking during 1:N connection (0.1-sec inter-cycle) 7-6 INP-TN5A0202-E 7.1 Error procedure Troubles during connecting the loader The diagram below shows the list of the cased frequently occurs and their solution. Refer the parameter loader for PUM user's manual as well. Troubles Causes Solutions Connection error to the parameter loader for PUM Check the connection status of the parameter loader connecting cable for PUM. Check if there is any connecting cable break. Check if the assembly of the parameter loader connecting cable for PUM correct. No connection to the PUM parameter loader is possible Parameter change is not possible INP-TN5A0202-E Communication conditions mismatch Check such as communication speed set value, parity set value. Wrong host Check that the parameter loader connecting cable for PUM is connected to the loader port of the programless communication module. Attempting the parameter input value writes the value out of the setting range Modify and write the input value within the setting range. 7-7 7.1 Error procedure 7-8 INP-TN5A0202-E Index Numeral I 1:1 connection …………………… 2-3,3-3,3-17,3-21,3-22 Insulation between terminals ………………………… 3-20 1:N connection …………………… 2-5,3-5,3-17,3-21,3-22 Inter-module communication ……………………… 2-3,2-5 Inter-PLC communication execution time monitor … 5-19 A Accessories ……………………………………… 1-4,3-13 L LED indicator……………………………………………… 1-6 B Loader communication ………………………………… 6-3 Base part …………… 1-5,1-9,3-7,3-8,3-9,3-10,3-14,3-23 Loader communication port ………… 1-6,1-7,4-9,6-3,6-5 Loader connecting cable ………………… 1-4,1-7,6-3,6-5 C Loader interface ……………………………… 6-3,6-4,6-6 Cautions when installing ……………………………… 3,3-7 Lock lever …………………………………………… 3-8,3-9 Command setting demand flag ……………… 4-4,4-5,4-21 Locking tab …………………………… 1-9,3-10,3-11,3-14 Command setting response flag …………… 4-4,4-7,4-21 Communication behavior configuration switch ……… 1-8 M Communication conditions ……………………………… 6-6 Main body …………………………………………… 1-5,3-7 Communication restoration demand …………… 4-5,4-23 Main part ………………………………………………… 1-8 Communication speed …………………………… 3-18,5-11 Main unit ………………………………………… 3-8,3-14 Communication unit ………… 2-3,2-5,3-17,3-21,3-22,5-11 Master/slave setting ………………………………… 3-3,3-5 Confirming accessories ………………………………… 1-3 Maximum transmission distance …………………… 3-18 Connecting modules …………………………… 3-11,3-12 MC protocol ……………………………………… 5-13,5-17 Connection with PLC …………………………… 3-15,3-21 MELSEC-Q/A/AnS/FX series ……… 1-3,2-3,2-5,3-15,3-18 CPU unit…………………………………………… 2-3 ,5-11 Memory area ………………………………………… 4-4,5-5 Model code ……………………………………………… 1-4 D Module connector …………………………… 1-9,3-11,3-13 Data field ………………………………… 4-3,4-4,4-6,4-8 Monitor area ………………… 4-3,4-4,4-7,5-5,5-8,5-9,5-18 Data part ………………………………………………… 6-9 Monitor area device size ………………………… 5-8,5-18 Device memory ………………………………… 4-3,4-4,4-12 Monitor area device type ………………………… 5-8,5-18 Dimensions ……………………………………………… 3-7 Monitor area entry register No. …5-9,5-10,5-51,5-64,5-71 Monitor area entry St. No. …………………………… 5-9, E 5-10,5-18,5-51,5-64,5-71 Endplate …………………………………………… 1-4,3-13 Monitor area start address ……………………………… 5-8 Equipment response ………………………………… 6-14 Mounting screw………………………………………… 3-14 Error check code …………………………… 6-9,6-10,6-12 Mounting screw hole …………………………………… 1-9 F N Frame detection ……………………………………… 6-13 Non-registerable parameter to the setting area …… 5-6, Front terminal block …………………………… 1-5,1-6,3-8 5-7,5-51,5-64,5-71 Function code ……………………………… 6-9,6-10,6-11 Number of retry times …………………………… 5-15,5-18 INP-TN5A0202-E 1 O Side connecting terminal covers ……………… 1-4,3-13 Operation setting when a programless Slave response ………………………………………… 6-10 communication fault occurs …………………………… 5-4 Crimp terminal ………………………………………… 3-23 Station No. …………… 1-7,2-4,2-6,3-12,4-15,5-3,6-6,6-10 P Station No. configuration switch …………………… 1-6, Parameter loader ………………… 1-7,2-3,2-5,3-3,3-5,7-7 1-7,5-18,6-6,6-7 Parameter setting demand flag ………………… 4-5,4-18 System configuration ……………………………… 2-3,2-5 Parameter setting response flag ……………… 4-7,4-18 System field ……………………………… 4-3,4-4,4-5,4-7 PLC communication inter-cycle time …………… 5-14,5-18 PLC communication speed ……………………… 5-11,5-18 T PLC communication starting time ……………… 5-14,5-18 Terminal ………………………………………………… 3-20 PLC error code ………………………………………… 5-19 Terminal layout ………………………………………… 3-23 PLC error counter ……………………………………… 5-19 Terminal resistance …………………………………… 3-20 PLC inter-cycle time over counter …………………… 5-19 PLC receiving counter ………………………………… 5-19 W PLC response monitoring time ……………4-12,5-15,5-18 Wiring for power supply ……………………………… 3-23 PLC sending counter ………………………………… 5-19 Writing set values ……………………… 4-3,4-9,4-19,4-20 PLC transmission setting …………………………… 5-12 Writing word data ………………………………… 6-20,6-22 PUM parameter loader ………… 1-7,2-3,2-5,3-3,3-5,7-7 R Reading demand flag …………………………… 4-5,4-13 Reading monitor value ……………… 4-3,4-10,4-14,4-15 Reading response flag ………………………… 4-7,4-13 Reading set values …………………… 4-3,4-11,4-16,4-17 Reading word data ……………………………… 6-15,6-18 Recommended power supply ………………………………4 Responding frame …………………………………… 5-15 RS-232C ……………………………………… 1-6,1-8,3-18 RS-422 ………………………………………… 1-6,1-8,3-18 RS-485 ………………………………………… 1-6,1-8,3-18 S Sending frame ………………………………………… 5-15 Setting area ……………… 4-3,4-4,4-5,4-12,5-5,5-6,5-18 Setting area device size ………………………… 5-5,5-18 Setting area device type ………………………… 5-5,5-18 Setting area entry register No. … 5-6,5-7,5-51,5-64,5-71 Setting area entry St. No. ……… 5-6,5-7,5-51,5-64,5-71 Setting area start address ……………………………… 5-5 Setting error …………………………………………… 5-18 Setting/Monitor area register numbers ……5-51,5-64,5-71 2 INP-TN5A0202-E International Sales Div.1 Sales Group Gate City Ohsaki, East Tower, 11-2, Osaki 1-chome, Shinagawa-ku, Tokyo 141-0032, Japan http://www.fesys.co.jp/eng Phone: 81-3-5435-7280, 7281 Fax: 81-3-5435-7425 http://www.fic-net.jp/eng INP-TN5A0202-E