Download Chauvet Freedom Par User manual
Transcript
User Manual TABLE OF CONTENTS 1. Before You Begin................................................................................3 What Is Included ........................................................................................... 3 Unpacking Instructions .................................................................................. 3 Claims ................................................................................................................... 3 Text Conventions .......................................................................................... 3 Icons ............................................................................................................. 3 Document Information ................................................................................... 3 Product at a Glance....................................................................................... 4 Safety Notes ................................................................................................. 4 2. Introduction.........................................................................................5 Product Overview (Freedom™ Par) ............................................................... 5 Product Overview (Freedom™ Strip Mini) ...................................................... 6 Product Dimensions (Freedom™ Par) ........................................................... 7 Product Dimensions (Freedom™ Strip Mini) .................................................. 8 3. Setup ...................................................................................................9 AC Power ...................................................................................................... 9 Charging The Battery ............................................................................................. 9 Battery Life Indicator .............................................................................................. 9 Battery Maintenance .............................................................................................. 9 Fuse Replacement ............................................................................................... 10 Power Linking ...................................................................................................... 11 Mounting ..................................................................................................... 12 Orientation ........................................................................................................... 12 Rigging ................................................................................................................ 12 4. Operation ..........................................................................................13 Control Panel Operation .............................................................................. 13 Menu Map ................................................................................................... 13 Configuration (DMX).................................................................................... 14 Starting Address .................................................................................................. 14 DMX Personalities................................................................................................ 14 DMX Channel Assignments and Values....................................................... 15 4-CH.................................................................................................................... 15 3-CH.................................................................................................................... 15 Configuration (Standalone) .......................................................................... 16 Automatic Mode ................................................................................................... 16 Auto Programs ..................................................................................................... 17 IRC (Infrared Remote Control) .............................................................................. 17 D-Fi™ 2.4 Ghz (DMX Mode Auto Sync) ............................................................... 19 D-Fi™ 2.4 Ghz (DMX Mode Manual Sync) ............................................................ 20 D-Fi™ 2.4 Ghz (IR/Standalone Mode Auto Sync) .................................................. 21 D-Fi™ 2.4 Ghz (IR/Standalone Mode Manual Sync) .............................................. 22 Master/Slave Mode .............................................................................................. 23 Master/Slave Runway Effect ................................................................................. 24 5. Technical Information ......................................................................25 Product Maintenance .................................................................................. 25 Contact Us .................................................................................................. 26 Returns ....................................................................................................... 26 6. Technical Specifications ..................................................................27 Page 2 of 28 Freedom™ series User Manual (Rev. 6) 1. BEFORE YOU BEGIN What Is Included • • • • • Freedom™ Par or Freedom™ Strip Mini Power Cord Warranty Card User Manual Unpacking Instructions Immediately upon receipt, carefully unpack the product and check the container to make sure you have received all the parts indicated above in good condition. Claims If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, upon receipt notify the carrier immediately, not CHAUVET®. Failure to do so in a timely manner may invalidate your claim with the carrier. In addition, keep the container and all the packing material for inspection. For other issues such as missing components or parts, damage not related to shipping, or concealed damage, file a claim with CHAUVET® within seven (7) days of receiving the merchandise. Text Conventions Convention 1~512 50/60 Settings Menu > Settings <ENTER> ON Icon Icons Meaning A range of values A set of values of which only one can be chosen A menu option not to be modified A sequence of menu options to be followed A key to be pressed on the product’s control panel A value to be entered or selected Meaning This paragraph contains critical installation, configuration, or operation information. Failure to comply with this information may render the product partially or completely inoperative, cause damage to the product, or cause harm to the user. This paragraph contains important installation or configuration information. Failure to comply with this information may prevent the product from functioning correctly. Useful information. Document Information The information and specifications contained in this document are subject to change without notice. CHAUVET® assumes no responsibility or liability for any errors or omissions that may appear in this manual. CHAUVET® reserves the right to update the existing document or to create a new document to correct any errors or omissions. You can download the latest version of this document from www.chauvetlighting.com. © Copyright 2012 CHAUVET®. All rights reserved. Electronically published by CHAUVET® in the United States of America. Printed in the P.R.C. Author Date Editor Date A. Diaz 4/13/12 S. Graham 4/13/12 Freedom™ series User Manual (Rev. 6) Page 3 of 28 Product at a Glance Use on Dimmer Outdoor Use Sound Activated DMX Master/Slave Safety Notes Auto Programs Auto-ranging Power Supply Replaceable Fuse User Serviceable Duty Cycle Please read the following Safety Notes carefully before working with the product. The notes include important safety information about installation, usage, and maintenance. • • • • • • • • • • • • • • • • • • • Always connect the product to a grounded circuit to avoid the risk of electrocution. Always disconnect the product from the power source before cleaning or replacing the fuse. Avoid direct eye exposure to the light source while the product is on. Make sure the power cord is not crimped or damaged. Never disconnect the product from power cord by pulling or tugging on the cord. If mounting the product overhead, always secure to a fastening device using a safety cable. Make sure there are no flammable materials close to the product when operating. Do not touch the product’s housing when operating because it may be very hot. Always make sure that the voltage of the outlet to which you are connecting the product is within the range stated on the decal or rear panel of the product. The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not expose the product to rain or moisture. Always install the product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent surfaces. Be sure that no ventilation slots on the product’s housing are blocked. Never connect the product to a dimmer. Make sure to replace the fuse with another of the same type and rating. Never carry the product from the power cord or any moving part. Always use the hanging/mounting bracket or the handles. The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate the product at higher temperatures. In the event of a serious operating problem, stop using the product immediately. Never try to repair the product. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center Keep this User Manual for future use. If you sell the product to another user, be sure that they also receive this document. The Freedom™ series products contain rechargeable batteries. These batteries contain hazardous chemicals that cannot be discarded with household waste. Contact your local waste management service for recycling information when disposing of your product. Page 4 of 28 Freedom™ series User Manual (Rev. 6) 2. INTRODUCTION Product Overview (Freedom™ Par) Power Out Safety Eye Bolt Master/Slave Output DMX In Freedom™ series User Manual (Rev. 6) Power In Fuse Holder DMX Out Page 5 of 28 Product Overview (Freedom™ Strip Mini) Safety Hook Antenna Battery Life Indicator Microphone On/Off Switch LED Display D-Fi™ Auto Search Master/Slave Output DMX Out DMX In Power Out Power In Fuse Holder Page 6 of 28 Freedom™ series User Manual (Rev. 6) Product Dimensions (Freedom™ Par) Freedom™ series User Manual (Rev. 6) Page 7 of 28 Product Dimensions (Freedom™ Strip Mini) Page 8 of 28 Freedom™ series User Manual (Rev. 6) 3. SETUP AC Power The Freedom™ series has an auto-ranging power supply that works with an input voltage range of 100~240 VAC, 50/60 Hz. To determine the power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart. The listed current rating indicates the product’s average current draw under normal conditions. Always connect the product to a protected circuit (circuit breaker or fuse). Make sure the product has an appropriate electrical ground to avoid the risk of electrocution or fire. Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel serves only as a 0% to 100% switch. Charging The Battery The Freedom™ series comes with a non-replaceable lithium-ion battery for cable-free operation. To charge the Freedom™ series battery, simply plug in the power cord at any time before, during, or after operation. To charge the battery before or after operation with all the LEDs off, leave the power switch in the Off position. Battery Life Indicator The battery life indicator located on the product displays the remaining amount of internal battery life. Use the chart below to find out how much battery life remains per charge cycle. The light to the far right flashes during charging. Battery Maintenance The Freedom™ series should be charged 24 hours prior to initial use for optimal battery usage. To keep the battery in optimal operating condition, store the product in a cool, dry place and charge at least once every 30 days when not in use. Avoid exposure to extreme temperatures. If the product is exposed to extreme cold or hot temperatures, warm up/cool down the product before use and before charging. Run Time Table Freedom™ series User Manual (Rev. 6) Maximum Run Time Recharge Time 8 hours 6 hours Page 9 of 28 Disconnect the product from the power outlet before replacing the fuse. Fuse Replacement 1. 2. 3. 4. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder. Pry the fuse holder out of the housing. Remove the blown fuse from the holder and replace with a fuse of the exact same type and rating. Insert the fuse holder back in place and reconnect power. Installed fuse (held by plastic clip) Safety cap Spare fuse holder (inside safety cap) The product does not ship with a spare fuse; however, the safety cap has room for a spare. Always replace a blown fuse with a fuse of the same type and rating. Page 10 of 28 Freedom™ series User Manual (Rev. 6) Power Linking The product provides power linking via the IEC outlet located in the back of the unit. Please see the diagram below for further explanation. • Power Linking Diagram 1st Product 2nd Product 3rd Product Other products You can power link up to twelve (12) Freedom™ Par units on 120 VAC or up to twenty-two (22) Freedom™ series units on 230 VAC. You can power link up to seventeen (17) Freedom™ Strip Mini units on 120 VAC or up to thirty-two (32) Freedom™ series units on 230 VAC. The power linking diagram shown above corresponds to the North American version of the product ONLY! If using the product in other markets, you must consult with the local CHAUVET® distributor because power linking connectors and requirements may differ in your country or region. Freedom™ series User Manual (Rev. 6) Page 11 of 28 Mounting Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes. Orientation The Freedom™ series may be mounted in any position; however, make sure adequate ventilation is provided around the product. Rigging • Before deciding on a location for the product, always make sure there is easy access to the product for maintenance and programming purposes. • Make sure that the structure or surface onto which you are mounting the product can support the product’s weight. Refer to the Technical Specifications section of this manual for weight information. • When mounting the product overhead, always use a safety cable. Mount the product securely to a rigging point, whether an elevated platform or a truss. • When rigging the product onto a truss, you should use a mounting clamp of appropriate weight capacity. The bracket has a 13-mm hole, which is appropriate for this purpose. • When power linking multiple products, you must always consider the length of the power linking cable and mount the products close enough for the cable to reach. • The bracket adjustment knobs allow for directional adjustment when aiming the product to the desired angle. Only loosen or tighten the bracket knobs manually. Using tools could damage the knobs. • The tilt angle adjustment knob on the Freedom™ Par enables fine adjustment of the light angle. Loosen the adjustment knob to move the upper area of the Freedom™ Par to your desired angle. • The double-bracket yoke on the Freedom™ Strip Mini also serves as a floor support or allows for surface mounting. When mounting the product on the floor, make sure that the product and cables are away from people and vehicles. Tilt Angle Adjustment Knob Mounting Bracket Bracket Adjustment Knob Mounting Diagrams Bracket Adjustment Knob Mounting Bracket Page 12 of 28 Freedom™ series User Manual (Rev. 6) 4. OPERATION Control Panel Operation To access the control panel functions, use the four buttons located around the display. Please refer to the Product Overview to see the button locations on the control panel. Button <MODE> <UP> Menu Map Function Press to find an operation mode or to back out of the current menu option Press to scroll up the list of options or to find a higher value <DOWN> Press to scroll down the list of options or to find a lower value <ENTER> Press to activate a menu option or a selected value Mode Programming Steps SdAd 000–509 d-CH SYS Turn on 3-channel DMX mode 4 CH Turn on 4-channel DMX mode tA.s t-AU Automatically select Transmit frequency (for IR use) t.CH t001t016 Manually select Transmit frequency (for IR use) dRA.S dR.AU Automatically select Receive frequency (for DMX use) dR.CH dr.01dr.16 Manually select Receive frequency (for DMX use) dtA.S dt.AU Automatically select Transmit frequency (for DMX use) dt.CH dt.01dt.16 Manually select Transmit frequency (for DMX use) SL.00–SL.32 SAAd ACt (extra levels not available in all programs) SL.00–SL.32 Sound sensitivity (Automatic Mode) P000–P100 Run speed (slow to fast) Dimmer (brightness increasing) r-AU r-st r001-r016 SLAv Freedom™ series User Manual (Rev. 6) Flash speed (slow to fast) C000–C100 rA.S S-1r Set sound sensitivity (DMX Mode) Reset software F000–F100 A000–A023 Set DMX address 3 CH S-tr d-SL Description Automatically select Receive frequency (for IR use) Manually select Receive frequency (for IR use) Infrared connection with Infrared Remote Control (IRC) only Page 13 of 28 Configuration (DMX) Set 1. 2. 3. the product in DMX mode to control with a DMX controller. Connect the product to a suitable power outlet. Turn the product on. Connect a DMX cable from the DMX output of the DMX controller to the DMX input socket on the product. Starting Address When selecting a starting DMX address, always consider the number of DMX channels the selected DMX mode uses. If you choose a starting address that is too high, you could restrict the access to some of the product’s channels. The Freedom™ series uses up to four (4) DMX channels in 4-channel DMX mode, which defines the highest configurable address to 509. If you are not familiar with the DMX protocol, download the DMX Primer from www.chauvetlighting.com. To select the starting address, do the following: 1. Press <MODE> repeatedly until SYS, ACt, SLAv, or S-1r shows on the display. 2. Use <UP> or <DOWN> to select SYS. 3. Press <ENTER>. 4. Use <UP> or <DOWN> to select SdAd from the menu. 5. Press <ENTER>. 6. Use <UP> or <DOWN> to select the starting address. 7. Press <ENTER>. DMX Personalities The Freedom™ series has two DMX personalities. One is a basic 3-channel personality, and the other is a more advanced 4-channel personality. To select either the Freedom™ series’ 3- or 4-channel personalities, use the following steps: 1. Press <MODE> repeatedly until SYS, ACt, SLAv, or S-1r shows on the display. 2. Use <UP> or <DOWN> to select SYS. 3. Press <ENTER>. 4. Use <UP> or <DOWN> to select d-CH from the menu. 5. Press <ENTER>. 6. Use <UP> or <DOWN> to select either the basic 3-channel mode (3CH) or the advanced 4-channel mode (4CH). 7. Press <ENTER>. Page 14 of 28 Freedom™ series User Manual (Rev. 6) DMX Channel Assignments and Values 4-CH Channel 1 3-CH Function Value CH.2 Blackout 000 009 Red 010 019 Green 020 029 Blue 030 039 Red + Green 040 049 Red + Blue 050 059 Blue + Green 060 069 Red + Green + Blue 070 079 Color Change 1 080 089 Color Change 2 090 099 Quadrant Effect 1 100 109 Quadrant Effect 2 110 119 Quadrant Effect 3 120 129 Quadrant Effect 4 130 139 Quadrant Effect 5 140 149 Quadrant Effect 6 150 159 Quadrant Effect 7 160 169 Quadrant Effect 8 170 179 Color Change 3 180 189 Color Change 4 190 199 Color Change 5 200 209 RGB Mode 210 219 Red (0~100%) Color Mode 220 229 Fade Speed (0~100%) Auto Run (sound active only) 230 255 Channel Function Value CH.4 Flash Speed 000 249 Sound Active 250 255 Flash Speed 000 249 Run Speed Sound-Active 250 255 Automatic 000 127 Sound-Active 128 255 Green (0~100%) Blue (0~100%) Setting 1 Red 000 255 0~100% 2 Green 000 255 0~100% 3 Blue 000 255 0~100% Freedom™ series User Manual (Rev. 6) CH.3 Page 15 of 28 Configuration (Standalone) Set the product in one of the standalone modes to control without a DMX controller. 1. Connect the product to a suitable power outlet. 2. Turn the product on. Never connect a product that is operating in any standalone mode to a DMX string connected to a DMX controller. Products in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller. Automatic Mode To enable the Automatic Mode, do the following: 1. Press <MODE> repeatedly until SYS, ACt, SLAv, or S-1r shows on the display. 2. Use <UP> or <DOWN> to select ACt. 3. Press <ENTER>. 4. Use <UP> or <DOWN> to choose your desired program (A000–A023). 5. Press <ENTER>. Certain programs will have additional functionality. To find these options, press <ENTER> after selecting an auto program. Then press <UP> or <DOWN>. Not every program will feature all the added functionality. Page 16 of 28 Function Description F000–F100 Flash speed (slow to fast) SL.00–SL.32 Sound sensitivity (Automatic Mode) P000–P100 Run speed (slow to fast) C000–C100 Dimmer (brightness increasing) Freedom™ series User Manual (Rev. 6) Auto Programs Program Function A000 No function A001 Red A002 Green A003 Blue A004 Red + Green A005 Red + Blue A006 Blue + Green A007 Red + Green + Blue A008 Color Change 1 A009 Color Change 2 A010 Quadrant Effect 1 A011 Quadrant Effect 2 A012 Quadrant Effect 3 A013 Quadrant Effect 4 A014 Quadrant Effect 5 A015 Quadrant Effect 6 A016 Quadrant Effect 7 A017 Quadrant Effect 8 A018 Color Change 3 A019 Color Change 4 A020 Color Change 5 A021 RGB Full On In this channel: P – Red F – Green C – Blue A022 Color Fade A023 Sound-Active IRC (Infrared Remote Control) The Freedom™ series is fully compatible with the IRC (Infrared Remote Control) from CHAUVET ® (sold separately). To set up the IRC to operate with the Freedom™ series, do the following: 1. Press <MODE> repeatedly until SYS, ACt, SLAv, or S-1r shows on the display. 2. Use <UP> or <DOWN> to select S-1r. 3. Press <ENTER>. 4. Begin using the IRC. Freedom™ series User Manual (Rev. 6) Page 17 of 28 IRC (Infrared Remote Control) Operation Note: Make sure to point the IRC directly at the receiver on the product. Automatic Mode Automatic Mode will enable you to run the automatic programs on the product. To turn on Automatic Mode: 1. Press AUTO on the IRC. 2. Press + or – to choose between the different auto programs. To adjust the speed of the automatic program: 1. Press SPEED on the IRC. 2. Press %. 3. Press + or – to either increase or decrease the speed of the program. Sound-Active Mode Sound-Active mode will enable the product to respond to music. To turn on Sound-Active mode: 1. Press SOUND on the IRC. To adjust sound sensitivity in Sound-Active mode: 1. Press SENSITIVITY on the IRC. 2. Press %. 3. Press + or – to either increase or decrease sound sensitivity. Manual Color Control To choose a specific color with the IRC: 1. Press MANUAL on the IRC. 2. Press any number between 0-9 to choose your color. To manually control the RGB percentage: 1. Press MANUAL on the IRC. 2. Press R, G, or B to choose your color. 3. Press + or – to increase or decrease the percentage of each color. Miscellaneous Operation To adjust the strobe rate of the program: 1. Press STROBE on the IRC. 2. Press + or – to increase or decrease the strobe rate. 3. Press STROBE again to turn off the strobe. To change the switching effect of the program: Press FADE/SNAP on the IRC. Fade will slowly switch the effect. Snap will rapidly switch the effect. To black out the lights: Press BLACK OUT on the IRC. This will turn off all the lights until the button is pressed again. Note: The IRC will not respond to any inputs when black out is activated. If the remote does not respond when a button is pressed, try pressing BLACK OUT. You may have inadvertently activated BLACK OUT. Page 18 of 28 Freedom™ series User Manual (Rev. 6) D-Fi™ 2.4 Ghz (DMX Mode Auto Sync) The Freedom™ series offers wireless control of two or more products with a single DMX controller. To automatically set up the D-Fi™ syncing function for DMX functionality, do the following: For the transmitting product: 1. Press <MODE> repeatedly until SYS, ACt, SLAv, or S-1r shows on the display. 2. Use <UP> or <DOWN> to select SYS. 3. Press <ENTER>. 4. Press <UP> or <DOWN> until S-tr appears on the display. 5. Press <ENTER>. 6. Press <UP> or <DOWN> until dtA.S appears on the display. 7. Press <ENTER>. 8. The display should show dt.AU. For the receiving product(s): 1. Press <MODE> repeatedly until SYS, ACt, SLAv or S-1r shows on the display. 2. Use <UP> or <DOWN> to select SYS. 3. Press <ENTER>. 4. Press <UP> or <DOWN> until S-tr appears on the display. 5. Press <ENTER>. 6. Press <UP> or <DOWN> until dRA.S appears on the display. 7. Press <ENTER>. 8. The display should show dR.AU. Once the steps above are done, press and hold <AUTO> on just the transmitter and for approximately 30 seconds. The display and signal LED will flash to indicate sync is activated. You can then back out to a general menu level and configure the transmitting product to operate it with a DMX controller. To configure your product to work with DMX, refer to the Starting Address section of the Operation section of this manual. To add additional Freedom™ products, turn the synced ones off and repeat the above steps with unsynced products. Once all products are synced, turn them all back on. Auto scan syncing must be done within a distance of about 32 ft (10 m). If you are experiencing antenna issues or need to improve signal quality, extend the antenna outward away from the product and keep the line of sight between products unobstructed. Ensure that all linked products are configured to the same DMX personality (either 3-channel or 4-channel). Caution: D-Fi™ operation can be interrupted or inhibited by liquid masses between the transmitter and receiver such as water, snow, or people. For best results, please keep the antenna clear of any liquid mass. Freedom™ series User Manual (Rev. 6) Page 19 of 28 D-Fi™ 2.4 Ghz (DMX Mode Manual Sync) The Freedom™ series offers wireless control of two or more products with a single DMX controller. To manually set up the D-Fi™ syncing function for DMX functionality, do the following: For the transmitting product: 1. Press <MODE> repeatedly until SYS, ACt, SLAv, or S-1r shows on the display. 2. Use <UP> or <DOWN> to select SYS. 3. Press <ENTER>. 4. Press <UP> or <DOWN> until S-tr appears on the display. 5. Press <ENTER>. 6. Press <UP> or <DOWN> until dt.CH appears on the display. 7. Press <ENTER>. 8. Use <UP> or <DOWN> to select the transmitting signal (dt.01-dt.16). For the receiving product(s): 1. Press <MODE> repeatedly until SYS, ACt, SLAv, or S-1r shows on the display. 2. Use <UP> or <DOWN> to select SYS. 3. Press <ENTER>. 4. Press <UP> or <DOWN> until S-tr appears on the display. 5. Press <ENTER>. 6. Press <UP> or <DOWN> until dR.CH appears on the display. 7. Press <ENTER>. 8. Use <UP> or <DOWN> to select the receiving signal (dr.01–dr.16). The channel number should match the transmitting signal you chose in the prior steps. Once the steps above are done, you can then back out to a more general menu level and configure the transmitting product to operate it with a DMX controller. To configure your product to work with DMX, refer to the Starting Address section of the Operation section of this manual. If you are experiencing antenna issues or need to improve signal quality, extend the antenna outward away from the product and keep the line of sight between products unobstructed. Ensure that all linked products are configured to the same DMX personality (either 3-channel or 4-channel). To sync multiple transmitters in one room, manually set each receiver and the designated transmitter to a specific frequency and then perform the syncing steps. The Freedom™ series is fully compatible with the D-Fi™ 2.4 GHz wireless transceiver (transmitter/receiver) from CHAUVET ® (sold separately). For more detailed information about D-Fi™ functionality, refer to the D-Fi™ 2.4 GHz User Manual available at the CHAUVET ® website: www.chauvetlighting.com Page 20 of 28 Freedom™ series User Manual (Rev. 6) D-Fi™ 2.4 Ghz (IR/Standalone Mode Auto Sync) The Freedom™ series can be configured to control two or more products with no external controllers or with the IRC from CHAUVET ® (sold separately). To automatically set up the D-Fi™ syncing function for IR/standalone functionality, do the following: For the transmitting product: 1. Press <MODE> repeatedly until SYS, ACt, SLAv, or S-1r shows on the display. 2. Use <UP> or <DOWN> to select SYS. 3. Press <ENTER>. 4. Press <UP> or <DOWN> until S-tr appears on the display. 5. Press <ENTER>. 6. Press <UP> or <DOWN> until tA.s appears on the display. 7. Press <ENTER>. 8. The display should show t-AU. For the receiving product(s): 1. Press <MODE> repeatedly until SYS, ACt, SLAv, or S-1r shows on the display. 2. Use <UP> or <DOWN> to select SLAv. 3. Press <ENTER>. 4. Press <UP> or <DOWN> until rA.S appears on the display. 5. Press <ENTER>. 6. The display should show r-AU. Once the steps above are done, press and hold <AUTO> on just the transmitter and for approximately 30 seconds. The display and signal LED will flash to indicate sync is activated. You can then back out to a more general menu level and configure the transmitting product to operate it in Automatic Mode or with an IRC (sold separately). To configure your product to work in Automatic Mode, refer to the Automatic Mode section of the Operation section of this manual. To configure your product to work with the CHAUVET ® IRC, refer to the IRC (Infrared Remote Control) section of the Operation section of this manual. To add additional Freedom™ products, turn the synced ones off and repeat the above steps with unsynced products. Once all products are synced, turn them all back on. Auto scan syncing must be done within a distance of about 30 ft (10 m). If you are experiencing antenna issues or need to improve signal quality, extend the antenna outward away from the product and keep the line of sight between products unobstructed. Ensure that all linked products are configured to the same DMX personality (either 3-channel or 4-channel). Freedom™ series User Manual (Rev. 6) Page 21 of 28 D-Fi™ 2.4 Ghz (IR/Standalone Mode Manual Sync) The Freedom™ series can be configured to control two or more products with no external controllers or with the IRC from CHAUVET ® (sold separately). To manually set up the D-Fi™ syncing function for IR/standalone functionality, do the following: For the transmitting product: 1. Press <MODE> repeatedly until SYS, ACt, SLAv, or S-1r shows on the display. 2. Use <UP> or <DOWN> to select SYS. 3. Press <ENTER>. 4. Press <UP> or <DOWN> until S-tr appears on the display. 5. Press <ENTER>. 6. Press <UP> or <DOWN> until t.CH appears on the display. 7. Press <ENTER>. 8. Use <UP> or <DOWN> to select the transmitting signal (t001–t016). For the receiving product(s): 1. Press <MODE> repeatedly until SYS, ACt, SLAv, or S-1r shows on the display. 2. Use <UP> or <DOWN> to select SLAv. 3. Press <ENTER>. 4. Press <UP> or <DOWN> until r-st appears on the display. 5. Press <ENTER>. 6. Use <UP> or <DOWN> to select the receiving signal (r001–r016). The channel number should match the transmitting signal you chose in the prior steps. Once the steps above are done, you can then back out and configure the transmitting product to operate it in either Automatic Mode or with an IRC (sold separately). To configure your product to work in Automatic Mode, refer to the Automatic Mode section of the Operation section of this manual. To configure your product to work with the CHAUVET ® IRC, refer to the IRC (Infrared Remote Control) section of the Operation section of this manual. If you are experiencing antenna issues or need to improve signal quality, extend the antenna outward away from the product and keep the line of sight between products unobstructed. Ensure that all linked products are configured to the same DMX personality (either 3-channel or 4-channel). To sync multiple transmitters in one room, manually set each receiver and the designated transmitter to a specific frequency and then perform the syncing steps. Page 22 of 28 Freedom™ series User Manual (Rev. 6) Master/Slave Mode The Master/Slave mode enables a single Freedom™ series product (the “master”) to control the actions of one or more other Freedom™ series products (the “slaves”) without the need of a DMX controller. The master product will be set to operate in Automatic Mode, while the slave products will be set to operate in Slave Mode. Once set and connected, the slave products will operate in unison with the master. Configure the products as indicated below. Slave products: 1. Connect the DMX input of the first slave product to the DMX link output of the master. The slave product will automatically switch to slave mode. The display will show SLA when this occurs. 2. Connect the DMX input of the subsequent slave products to the DMX link output of the previous slave. 3. Finish setting and connecting all the slave products. Master product: 1. Set the master to operate in Automatic Mode. 2. Make the master the first product in the DMX daisy chain. • Configure all the slave products before connecting the master to the DMX daisy chain. • Never connect a DMX controller to a DMX string configured for Master/Slave operation because the controller may interfere with the signals from the master product. • Do not connect more than 31 slave products to the master. Freedom™ series User Manual (Rev. 6) Page 23 of 28 Master/Slave Runway Effect The Master/Slave Runway Effect enables a single Freedom™ series product (the “master”) to control the actions of one or more other Freedom™ series products (the “slaves”) in sequential order for a “runway” effect without the need of a DMX controller. The master product will be set to operate in specific Automatic modes, while the slave products will be set to operate in Slave Mode. Once set and connected, the slave products will operate in unison with the master. Configure the products as indicated below. 1. Connect the DMX input of the first slave product to the DMX link output of the master. The slave product will automatically switch to slave mode. The display will show SLA when this occurs. 2. Connect the DMX input of the subsequent slave products to the DMX link output of the previous slave. 3. Once your setup is complete, reset the software in the master product using the steps below. This will also reset the software of all connected slave products. a. 4. Page 24 of 28 Press <MODE> repeatedly until SYS, ACt, SLAv, or S-1r shows on the display. b. Use <UP> or <DOWN> to select SYS. c. Press <ENTER>. d. Press <UP> or <DOWN> until SAAd appears on the display. e. Press <ENTER>. On the master product, choose your auto program as described in the Automatic Mode section of this manual. The only auto programs that can achieve this functionality are auto programs 14–20. Freedom™ series User Manual (Rev. 6) 5. TECHNICAL INFORMATION Product Maintenance Dust build-up reduces light output performance and can cause overheating. This can lead to reduction of the light source’s life. To maintain optimum performance and minimize wear, you should clean your lighting products at least twice a month. However, be aware that usage and environmental conditions could be contributing factors to increasing the cleaning frequency. To clean the product, use the following instructions: • Unplug the product from power. • Wait until the product is cold. • Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the external surface/vents. • Clean all transparent surfaces with a mild soap solution, ammonia-free glass cleaner, or isopropyl alcohol. • Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue. • Softly wipe any dirt or grime to the outside edge of the transparent surface. • Gently polish the transparent surfaces until they are free of haze and lint. Always dry the transparent surfaces carefully after cleaning them. Freedom™ series User Manual (Rev. 6) Page 25 of 28 In case you need to return a product or request support, follow the procedure below: • • • Contact Us If you live in the U.S., contact CHAUVET® World Headquarters (see below). If you live in the UK or Ireland, contact CHAUVET® Europe Ltd. (see below). If you live in any other country, DO NOT contact CHAUVET®. Instead, contact your distributor of record. Refer to our website for contact details of distributors outside the U.S., United Kingdom, or Ireland. World Headquarters CHAUVET® General Information Address: 5200 NW 108th Avenue Sunrise, FL 33351 Voice: (954) 929-1115 Fax: (954) 929-5560 Toll free: (800) 762-1084 Technical Support Voice: (954) 929-1115 (Press 4) Fax: (954) 756-8015 Email: [email protected] World Wide Web www.chauvetlighting.com United Kingdom & Ireland CHAUVET® Europe Ltd. General Information Address: Unit 1C Brookhill Road Industrial Estate Pinxton, Nottingham, UK NG16 6NT Voice: +44 (0)1773 511115 Fax: +44 (0)1773 511110 Technical Support Email: [email protected] World Wide Web www.chauvetlighting.co.uk If you live outside the U.S., United Kingdom, or Ireland, contact your distributor of record and follow their instructions on how to return CHAUVET® products to them. Visit our website for contact details. Returns Call the corresponding CHAUVET® Tech Support office and request a Return Merchandise Authorization (RMA) number before shipping the product. Be prepared to provide the model number, serial number, and a brief description of the cause for the return. You must send the merchandise prepaid, in its original box, and with its original packing and accessories. CHAUVET® will not issue call tags. Clearly label the package with the RMA number. CHAUVET® will refuse any product returned without an RMA number. Write the RMA number on a properly affixed label. DO NOT write the RMA number directly on the box. Before sending the product, clearly write the following information on a piece of paper and place it inside the box: • Your name • Your address • Your phone number • The RMA number • A brief description of the problem Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be your responsibility. FedEx packing or double-boxing are recommended. CHAUVET® reserves the right to use its own discretion to repair or replace returned product(s). Page 26 of 28 Freedom™ series User Manual (Rev. 6) 6. TECHNICAL SPECIFICATIONS Dimensions and Weight Length (Par) Width (Par) Height (Par) Weight (Par) 8.5 in (215 mm) Length (Strip Mini) 9.3 in (236 mm) Width (Strip Mini) 8.8 in (223 mm) Height (Strip Mini) 7.8 lbs (3.5 kg) Weight (Strip Mini) 19 in (482 mm) 5.5 in (240 mm) 2 in (52 mm) 6.2 lbs (2.8 kg) Note: Dimensions in inches rounded to the nearest decimal digit. Note: Unless otherwise indicated, all specifications are applicable to both the Freedom™ Par and the Freedom™ Strip Mini. Power Power Supply Type Range Voltage Selection Switching (internal) 100~240 V, 50/60 Hz Auto-ranging Freedom™ Par 120 V, 60 Hz 230 V, 50 Hz Consumption 80 W 85 W Operating 0.6 A 0.4 A Power linking current (units) 8 A (12 units) 8 A (22 units) Fuse Freedom™ Strip Mini F 2 A, 250 V 120 V, 60 Hz F 2 A, 250 V 230 V, 50 Hz Consumption 94 W 99 W Operating 0.8 A 0.4 A Power linking current (units) 8 A (17 units) 8 A (32 units) Fuse F 2 A, 250 V F 2 A, 250 V Power I/O US/Worldwide UK/Europe Power input connector IEC IEC Power output connector Edison IEC Power Cord plug Edison (US) Local plug Light Source Photo Optic Battery and Wireless Thermal DMX Ordering Type Lifespan LED 50,000 hours Color Freedom™ Par Freedom™ Strip Mini Red 60 64 Green 69 64 Blue 69 64 Total LEDs 198 192 Parameter Freedom™ Par Freedom™ Strip Mini Illuminance @ 2 m 431 lx 395 lx Beam angle 21º 23º Field angle 39º 42º Parameter Maximum Run Time 8 hrs Recharge Time 6 hrs Operating Frequency 2.433~2.481 GHz Maximum External Temp. Cooling System 104° F (40° C) Convection I/O Connectors Connector Type Channel Range 3-pin XLR Sockets 3, 4 Product Name Item Code Item Number Freedom™ Par 02030459 FREEDOMPAR Freedom™ Strip Mini 02030458 FREEDOMSTRIPMINI Freedom™ series User Manual (Rev. 6) Page 27 of 28 Page 28 of 28 Freedom™ series User Manual (Rev. 6)