Download HDS4.1 User Manual (Booklet)

www.zektor.com
858•748•8250
Poway, CA 92064
Suite 401
12675 Danielson Ct
Zektor, LLC
Z E K T O R
Rev 1
ZEK T OR
2
3
4
High Definition Component Video Switch
1
HDS4.1
12/07/2005
Digital Video / Component Video / Multichannel Audio
Home Theater Switches
Z E K T O R
ii
HDS4.1 Component Video Switch
Contact Information ........................ 19
Warranty Policy ............................... 18
Resetting to Factory Defaults ........... 17
Disabling Front Panel or Remote ...... 15
Setting the Initial Power On State .... 13
Adjusting the Front Panel Intensity .. 11
Controlling the Front Panel Lights ..... 9
Three Simple Steps to a Remote! ........ 7
Easy, Simple, Instructions! ................. 5
An Overview of the HDS4.1 ................ 3
What’s Inside ..................................... 1
Contents
HDS4.1 Component Video Switch
21
20
HDS4.1 Component Video Switch
HDS4.1
Power Supply M odule
This User ’s M anual
ZE K T OR
1
2
4
HDS4.1 Component Video Switch
3
I f anything is missing please get in touch with us as soon as possible so thate we can correc t the situation.
1.
2.
3.
The following should be included:
Please take this time to verify the contents of the HDS4.1 box.
Ever y care has been taken to assure you of a successful installation and subsequent operations of your new HDS4.1 video switch,
however should something go wrong, and warrant y repair work
is needed, we request that you hold on to the original pack aging
materials.
Th a n k yo u fo r yo u r p u rc h a s e o f yo u r H D S 4 . 1 H i g h D e f i n i t i o n Co m ponent Video Switch.
What’s Inside
1
Y/G
2
1
R/V
Pr/R
C/V
2
Y/G
R/V
Pb/B
L/H
Pr/R
C/V
3
Y/G
R/V
1
Pb/B
L/H
Pr/R
C/V
4
Y/G
R/V
2
3
Pb/B
L/H
Pr/R
C/V
OUT
Y/G
R/V
Pb/B
L/H
Rear Panel
HDS4.1 Component Video Switch
Pb/B
L/H
ZEKTOR
Front Panel
Pr/R
C/V
4
4
1
OUT
2
OUT
3
1
2
3
DIGITAL AUDIO
4
OUT
9VDC
5
4
3
2
1
6
Phone:
Fax:
Email:
Website:
HDS4.1 Component Video Switch
858-748-8250
858-748-8224
[email protected]
www.zektor.com
Zektor, LLC
12675 Danielson Ct.
Suite 401
Poway, CA 92064
Customer Service Contact Information:
19
A l l re t u r n e d m e rc h a n d i s e m u s t b e s h i p p e d i n t h e o r i gi n a l p a c k a g i n g. I f i t i s n o t i n t h e o r i gi n a l p a c k a gi n g, Z E K TO R w i l l n o t b e h e l d
liable for damage during shipment. Shipments of returns must be
p re p a i d, a n d we w i l l n o t a cce p t CO D re t u r n s.
5
4
Yo u m u s t rece i ve a n R MA # b e fo re yo u re t u r n a ny g o o d s to u s. The
R MA # m u s t a p p e a r o n yo u r re t u r n p a c k in g l a b e l o r o n t h e o u t s i d e
of the box. M erchandise without a RMA # will be refused. RMA’s are
valid for t went y (20) days from date of issuance.
E-M ail us, or call us, using the information listed under “Customer
S er v i ce Con t a c t I nfor m a t i o n”, fo r a R e t u r n to M a n u f a c t u re r Au t h o r i z a t i o n ( R MA) n u m b e r. D e s c r i b e b r i e f l y t h e re a s o n s fo r yo u r re q u e s te d re t u r n .
Please retain the dated sales receipt as evidence of the date of
purchase. You will need it for any warrant y ser vice. I f you bought
the produc t through a dealer, installer, or reseller, you will need to
return the produc t to the point of sale.
3
2
1
Instructions for Returning Items
Contact Information
18
HDS4.1 Component Video Switch
Shipment of produc t is as adver tised by produc t. Upon receipt of
merchandise inspec t produc t carefully, should you find that the
produc t does not meet your expec tations, or satisfac tion, contac t
us at once and tell us your concerns, so we may make ever y effor t
to satisfy your purchase.
Return & Exchange
S ome states/countries do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation
or exclusion may not apply to you. S ome states/countries do not
allow limitations on how long an implied warrant y lasts, so the
above limitation may not apply to you. This warrant y gives you
specific legal rights, and you may also have other rights that var y
from state to state and countr y to countr y.
Repair or replacement, as provided under this warrant y, is your
exclusive remedy. ZEK TOR shall not be liable for any incidental or
consequential damages. I mplied warranties of merchantabilit y and
fitness for a par ticular purpose on this produc t are limited in duration to the duration of this warrant y.
I n order to keep this warrant y in effec t, the produc t must have
b e e n h a n d l e d a n d u s e d a s p re s c r i b e d i n t h e i n s t r u c t i o n s a cco m p a nying this warrant y. This warrant y does not cover any damage due
to accident, misuse, abuse, or negligence. This warrant y is valid
only if the produc t is used as specified in the produc t documentation.
ZEK TOR, LLC warrants this produc t against defec ts in material and
wor k m a n s h i p u n d e r n o r m a l u s e a n d s e r v i ce fo r t wo ye a r s f ro m t h e
original date of purchase. ZEK TOR, at its option, shall repair or re place the defec tive unit covered by this warrant y.
Warranty Policy
Warranty Policy
Power I ndicator. Lights up in standby mode.
S elec tion LEDs. I ndicate currently selec ted inputs.
I nput S elec tion Buttons.
I nfrared Remote S ensor Window.
I nfrared Received I ndicator. Flashes when IR is received.
Power Toggle Button.
5.
4.
2.
3.
1.
HDS4.1 Component Video Switch
3
Analog I nputs. Each input consists of six equivalent
channels. The channels are colored and labeled for convenience, however all six channels are of equivalent
bandwidth and func tionalit y, and may be interchanged as
desired.
Analog Outputs.
Digital Audio I nputs. Each input has an associated digital
a u d i o c h a n n e l w i t h b o t h a Co a x a n d a n O p t i c a l co n n e c tion. Only one of the t wo t ypes of inputs can be ac tive at
any time. The HDS4.1 will auto -selec t bet ween the t wo
t ypes of signals. I f a signal is supplied to both the Coax
a n d O p t i c a l i n p u t s, t h e Co a x s i gn a l i s give n p r i o r i t y.
DC Power Jack Connec tor. Plug in the supplied power
adapter into this jack .
Digital Audio Outputs. All digital audio inputs are auto matically conver ted to both Coax and Optical outputs. All
three outputs are available at all times, and are all individually buffered to allow driving three different digital
audio devices simultaneously.
Rear Panel Connections:
1.
2.
3.
4.
5.
6.
Front Panel Controls:
An Overview of the HDS4.1
Pb/B
Pr/R
C/V
2
L/H
Pb/B
To
Cable
Box
Y/G
R/V
Pr/R
C/V
3
To
DVD
Y/G
R/V
Pb/B
L/H
Pr/R
C/V
4
Unused
Input
Pb/B
L/H
To
Game
Console
Y/G
R/V
Pr/R
C/V
OUT
Y/G
R/V
Pb/B
L/H
2
3
Pr/R
C/V
4
4
1
OUT
3
1
4
5
8
4
7
+
_
CH
VOL
9
6
3
+
_
0
2
1
POWER
Projector
or
Monitor
To DVD
Digital Audio
2
3
4
3
OUT
To Home Theater
Receiver’s Digital
Audio Input
4
To Power
Module
9VDC
Turn to the next chapter for simple instructions
on how to setup the HDS4.1 for use with
any existing remote!
1
HDS4.1 Component Video Switch
ZEK TOR
2
DIGITAL AUDIO
To
Cable Box
Digital Audio To Game
Console
Digital Audio
To
OUT
2
To
Composite
Monitor
w/Analog
Audio
Step 3: Or use nearly ANY remote to select an input.
1
Step 2: Press buttons to select an input.
Y/G
L/H
ZEK TOR
1
R/V
Step 1: Make the appropriate connections.
3.
1.
2.
HDS4.1 Component Video Switch
17
First press and hold the Power button
While continuing to hold the Power Button, press and
hold both the ‘2’ and ‘3’ buttons.
Af ter holding all buttons for about ‘4’ seconds, the display
will flash indicating all parameters have been restored to
their fac tor y programmed values.
Step 1: Reset All Parameters to Factory Defaults
I f, for whatever reason, you’d like to reset your HDS4.1 back to its
fac tor y condition, this is easily done...
Resetting to Factory Defaults
16
1
1
3
2
2
4
...while continuing to hold the Power
button, press and hold both the ‘2’
and the ‘3’ buttons.
3
After about 4 seconds, the display will flash
indicating all parameters have been restored
to their factory programmed values.
HDS4.1 Component Video Switch
Start by pressing and
holding the Power
button...
Z EKTOR
Step 1: Reset All Parameters to Factory Defaults
Use nearly any remote to control your HDS4.1!
Using any remote to operate the HDS4.1 is a simple matte r o f p a i r i n g u p t h e H D S 4 . 1 w i t h t h e re m o te. Th e re m o te
doesn’t have to be a universal remote (although it can be),
a ny re m o te f ro m a n o l d T V o r V C R w i l l wor k j u s t f i n e.
Using Zektor ’s exclusive I ntelligent-IR, setup is easy! The
H D S 4 . 1 d o e s a l l t h e wor k !
To switch bet ween any of the four inputs, simply press
the button for the desired input. I f the HDS4.1 is in the
s t a n d by, i t w i l l t u r n o n . Th e H D S 4 . 1 w i l l t h e n s w i tc h to t h e
selec ted input, and the associated LED will light to indicate this.
To place the HDS4.1 back into the standby mode, press
and release the Power Toggle button. The channel LEDs
will all go blank , and the standby LED will light up. Press
the Power Toggle button again to re -selec t the previously
selec ted input.
Use the analog input connec tions to switch component
video / composite video / analog audio or any combination of the above signals to the HDS4.1’s analog output
connec tors. Use the digital audio connec tors to switch
digital audio signals, with full format conversion bet ween
the optical and coax digital audio formats.
Plug the power module into the HDS4.1, and plug the
module into a standard A.C. wall receptacle. The standby
LED will light up.
HDS4.1 Component Video Switch
5
Turn to the nex t chapter for simple instruc tions
on how to pair up the HDS4.1 with any remote!
•
•
•
Step 3...
•
•
Step 2...
•
•
Step 1...
Easy, Simple, Instructions!
2
3
4
Press and hold the Power Button for 4 secs.
The standby LED will blink wildly, and the
selection LEDs will start sequencing to the
right. (You’ll know it when it happens!)
1
1
2
6
8
7
+
_
5
4
0
2
1
+
_
9
6
3
POWER
1
3
4
That’s it! The HDS4.1 now operates with
your new remote control!
Power 1 2 3 4 8 9
Press the following sequence of buttons on
your remote control:
2
HDS4.1 Component Video Switch
ZEK TOR
4
...the standby LED will flash slower,
and all the other LEDs will turn off.
3
Step 3: Teach the HDS4.1 its new IR codes
Once the ‘1’ button
is pressed...
ZEK TOR
Step 2: Press the ‘1’ button for Intelligent-IR learning
ZEK TOR
Step 1: Put the HDS4.1 into the Setup Mode
First press and hold the Power button
While continuing to hold the Power Button, press and
hold the ‘4’ button.
Af ter holding both buttons for about ‘4’ seconds, the
standby LED will star t flashing quick ly indicating you are
now able to enable / disable front panel buttons and IR
control func tions.
The front panel selec tion LEDs now indicate the state of
the front panel and IR control settings:
I f ‘3’ is lit, then the Front Panel buttons are ENABLED.
I f ‘4’ is lit, then the IR remote func tions are ENABLED.
Use the ‘3’ button to ENABLE / DISABLE the front panel
buttons.
Use the ‘4’ button to ENABLE / DISABLE the IR remote control func tions.
When finished, press the ‘Power ’ button to save new settings and return to normal operations.
HDS4.1 Component Video Switch
15
Note 2: Disabling the front panel buttons does not disable the
a b i l i t y to e nte r t h e S e t u p M o d e s. Eve n w i t h t h e f ro nt
panel disabled you can per form the above steps, allowing you to once again enable the front panel buttons.
Note 1: The HDS4.1 will not allow you to disable both the front
panel and IR controls at the same time.
•
•
•
Step 2: Enable or Disable Front Panel and / or IR control
•
3.
1.
2.
Step 1: Enter the Enable / Disable control state
To enable/disable the front panel switches or remote capabilities...
Or if you have a household with young curious fingers that likes
playing with buttons, you also have the capabilit y of disabling the
front panel switches and only operating the HDS4.1 with a remote.
I f you are not planning on using a remote control with your
HDS4.1, you might want to disable its remote control func tion.
Disabling Front Panel or Remote
Start by pressing and
holding the Power
button...
1
3
2
...while continuing to hold the Power
button, press and hold the ‘4’ button.
4
After about 4 seconds, the standby LED
will flash quickly, and the display will indicate the current enable / disable statuses.
2
3
14
1
2
HDS4.1 Component Video Switch
ZEK TOR
3
4
Exit Setup Mode
Enable / Disable
Front Panel Buttons
Enable / Disable
IR Control Functions
Step 2: Enable or Disable Front Panel and / or IR Control Functions
1
Z EKTOR
Step 1: Enter the Enable / Disable Control State
Star t by pick ing the remote you’d like to use with the
HDS4.1. I f the remote you plan on using is not programmable (for instance, from an old T V ), sk ip the nex t step.
I f you plan on using a universal remote, star t by setting it
up as a remote for a T V or VCR that you do not own. (For
instance if you don’t own a S ony T V, setup your universal
remote to control a S ony T V.)
The HDS4.1 is placed into the setup mode by pressing and
holding the Power button for about 4 seconds.
That ’s it! The HDS4.1 will return to the state it was in be fore s e t u p, a n d w i l l n ow wor k w i t h yo u r n e w re m o te !
Power 1 2 3 4 8 9
On your remote control, press the following buttons, in
the following order :
Note:
Toggles the HDS4.1’s power.
S elec ts inputs 1 through 4.
Tur n s o n t h e H D S 4 . 1 ( D i s c re te O N )
Tur n s o f f t h e H D S 4 . 1 ( D i s c re te O F F ) .
HDS4.1 Component Video Switch
All remote control codes are saved in non-volatile
memor y and will not be lost during a power failure.
Power
1-4
8
9
The new control buttons on your remote are...
•
•
7
There are many options available in the setup mode, but
for now all we’re interested in is the I ntelligent-IR learning mode. This is selec ted by pressing the ‘1’ button.
Once the ‘1’ button is pressed, the standby LED will flash
s l owe r a n d a l l t h e o t h e r L E D s w i l l t u r n o f f. Th e H D S 4 . 1 i s
now waiting for new IR codes to be sent from your remote
control.
Step 3: Teach the HDS4.1 your new remote control codes
•
•
Step 2: Select the Intelligent-IR Learn Mode
•
Step 1: Put the HDS4.1 into the Setup Mode
•
•
Pick a remote, any remote!
The HDS4.1 features Zektor ’s Exclusive I ntelligent-IR, and with ver y
few exceptions can be setup to use any remote you can point at it!
Three Simple Steps to a Remote!
2
3
1
2
3
8
1
2
HDS4.1 Component Video Switch
ZEK TOR
3
Step 3: Choose a new lighting mode
After ‘3’ is pressed, the standby LED continues to flash, and
the front panel will display
the current Light Mode setting.
ZEK TOR
4
4
4
Exit Setup Mode
Auto-Fade
Always Bright
Always Dim
Always Off
Press and hold the Power Button for 4 secs.
The standby LED will blink wildly, and the
selection LEDs will start sequencing to the
right.
1
Step 2: Select “Lighting Mode” option
ZEK TOR
Step 1: Place the HDS4.1 into the Setup Mode
Use the front panel buttons to setup the HDS4.1 to the
operating settings you’d like at initial power up.
First press and hold the Power button.
While continuing to hold the Power button, press and
hold the ‘1’ button.
Af ter holding both buttons for about ‘4’ seconds, the display will blink indicating the new power on defaults have
been accepted.
•
•
HDS4.1 Component Video Switch
13
You can test the new defaults by either disconnec ting the
power supply from the back of the HDS4.1 or by unplugging the power supply from the wall.
Reconnec t power. The HDS4.1 will power up into your new
power on default state.
Test the new initial power on state
3.
1.
2.
Step 2: Save the new initial power on state.
•
Step 1: Setup the HDS4.1 to your preferred power on state.
To change the power on defaults...
I t is possible to change the power on behavior of the HDS4.1.
H owever, i f p owe r i s re m ove d ( fo r i n s t a n ce a p l u g s t r i p u s e d to
p owe r t h e H D S 4 . 1 i s t u r n e d o f f ) , a n d t h e n re - a p p l i e d, t h e H D S 4 . 1 ’s
default behavior is to enter into the standby mode.
As long as the HDS4.1 is plugged in, it will remember the previously selec ted input in standby mode. When powered up by pressing
the Power button, it will return to that previously selec ted channel.
Setting the Initial Power On State
1
2
3
4
12
1
1
3
HDS4.1 Component Video Switch
Start by pressing and
holding the Power
button...
Z EKTOR
2
...while continuing to hold the Power
button, press and hold the ‘1’ button.
4
After about 4 seconds, the display will
flash indicating the new power on state
has been accepted.
2
3
Step 2: Save the new initial power on state
Setup the HDS4.1 to
the initial power on
state you’d prefer.
ZEK TOR
Step 1: Set the HDS4.1 to the preferred initial power on state
automatically fade from bright to dim
inac tivit y.
are always at the bright level.
are always at the dim level.
are turned off.
The intensities of the both the bright and dim levels can
be adjusted as well, this is explained in the nex t chapter.
Front panel lights
af ter 4 seconds of
Front panel lights
Front panel lights
Front panel lights
The HDS4.1 is placed into the setup mode by pressing and
holding the Power button for about 4 seconds.
Note:
HDS4.1 Component Video Switch
The lighting mode setting is saved in non-volatile
memor y and is not affec ted by a power failure.
Choose a new light control mode by pressing the associated selec tion button.
Pre s s t h e Power B u t to n to s ave t h e n e w m o d e a n d re t u r n
to normal operations.
9
Press the ‘3’ button to selec t the “Lighting M ode” option.
The front panel selec tion LEDs now indicate the currently
selec ted light mode as follows:
I f ‘1’ is lit, then front panel lights are always off.
I f ‘2’ is lit, then front panel lights are always dim.
I f ‘3’ is lit, then front panel lights are always bright.
I f ‘4’ is lit, then front panel lights auto -fade from bright to
dim af ter 4 seconds of inac tivit y.
Step 3: Choose a new lighting mode
•
•
•
•
Step 2: Select the Lighting Mode option
•
Step 1: Enter the Setup Mode
To change the front panel lighting mode...
Note:
•
•
•
•
There are four different front panel light modes available on the
HDS4.1. They are:
Controlling the Front Panel Lights
2
3
4
1
2
3
10
1
2
HDS4.1 Component Video Switch
ZEK TOR
3
Step 3: Adjust front panel intensities
After ‘4’ is pressed, the standby LED continues to flash, and the front panel will
display the current intensity setting.
ZEK TOR
4
4
Exit Setup Mode
Brighter
Dimmer
Select BRIGHT level
Select DIM level
Press and hold the Power Button for 4 secs.
The standby LED will blink wildly, and the
selection LEDs will start sequencing to the
right.
1
Step 2: Select “Front Panel Intensity” option
ZEK TOR
Step 1: Place the HDS4.1 into the Setup Mode
The HDS4.1 is placed into the setup mode by pressing and
holding the Power button for about 4 seconds.
Press the ‘4’ button to selec t “Front Panel I ntensit y ” op tion.
The front panel selec tion LEDs now indicate the front
panel intensit y settings:
I f ‘1’ is lit, then the DIM level is being adjusted.
I f ‘2’ is lit, then the BRIGHT level being adjusted.
‘3’ and ‘4’ are always lit.
Note:
•
HDS4.1 Component Video Switch
The new intensity settings are saved in non-volatile
memor y and are not affec ted by a power failure.
11
Use the ‘1’ and ‘2’ buttons to switch bet ween the DIM and
BRIGHT settings.
Use the ‘3’ button to decrease the intensit y of the front
panel lights.
Use the ‘4’ button to increase the intensit y of the front
panel lights.
You cannot make the DIM level brighter than the BRIGHT
level, and you cannot make the BRIGHT level dimmer than
the DIM level.
Once the front panel intensities are acceptable, press the
Power button to save the new settings and exit the setup
mode.
Step 3: Adjust Front Panel Intensities
•
•
•
•
•
•
Step 2: Select the Front Panel Intensity option
•
Step 1: Enter the Setup Mode
To change the front panel intensities...
The bright and dim levels of the front panel lights of the HDS4.1
are user adjustable, allowing the HDS4.1 to blend into a wide
range of lighting conditions.
Adjusting the Front Panel Intensity