Download Bell System bellissimo Specifications
Transcript
Bell System (Telephones) Ltd. bellissimo Video Door Entry System 1 Way Installation & Operation Manual PD-097 Issue 2 TABLE OF CONTENTS INTRODUCTION ........................................................................................................ 1 DESCRIPTION ............................................................................................................ 1 MAIN FEATURES ........................................................................................................ 1 DIAGRAM 1: BELLISSIMO VIDEOPHONE .......................................................................... 2 BASIC SYSTEM OPERATION................................................................................... 3 Call sequence ...................................................................................................... 3 Silent viewing....................................................................................................... 3 Auto Display......................................................................................................... 3 Call Mute.............................................................................................................. 3 Door Status Indication.......................................................................................... 3 Call Privacy.......................................................................................................... 4 User Activation (CCTV Mode).............................................................................. 4 Second camera.................................................................................................... 4 Extension Videophones ....................................................................................... 4 Lock Type and Operation..................................................................................... 4 Exit Button and Fire Switch.................................................................................. 4 Trades Facility ..................................................................................................... 4 DDA Functionality ................................................................................................ 5 Multiple Entrances ............................................................................................... 5 DESIGN CONSIDERATIONS..................................................................................... 6 EQUIPMENT LIST ........................................................................................................ 6 OPTIONS ................................................................................................................... 6 Entrance Panel .................................................................................................... 6 Door Controller .................................................................................................... 6 POWER SUPPLY REQUIREMENTS................................................................................. 7 The system is powered by 12V PSU’s only: - ...................................................... 7 CABLE SPECIFICATION. .............................................................................................. 7 CAT5 cable .......................................................................................................... 8 Cable Distances (refer to diagrams A and C) ...................................................... 8 INSTALLATION & COMMISSIONING ....................................................................... 9 WIRING..................................................................................................................... 10 Entrance Panel .................................................................................................. 10 Videophone........................................................................................................ 10 Electric Door Release ........................................................................................ 10 Exit Button Input ................................................................................................ 10 Door Open Switch.............................................................................................. 10 BSD1 DOOR CONTROLLER SETTINGS ................................................................ 11 BSD1 DOOR CONTROLLER SWITCH SETTINGS .......................................................... 11 Talking Time/Videophone Active DIP SW1 (1-4) .............................................. 11 Ringing Time/Call Time and Ring Effect DIP SW1 (5-8) ................................... 11 Lock Operate Time Dip SW2 (1-3).................................................................... 12 Individual Functions DIP SW2 (4-8).................................................................. 12 Camera Numbering DIP SW3 (1-8) .................................................................. 13 Installation and Operating Manual Page ii View Activated by User ...................................................................................... 13 ‘Global View’ at Multiple Entrances.................................................................... 13 BSD1 DOOR CONTROLLER JUMPER SETTINGS .......................................................... 14 BS VIDEOPHONE SWITCH SETTINGS .................................................................. 15 Mute Time Setting SW1 (1-4) ........................................................................... 15 Individual Functions DIP SW1 (5-8).................................................................. 15 DIAGRAM A – 1 WAY BASIC SYSTEM OVERVIEW CABLING............................. 16 DIAGRAM B – 1 WAY BASIC SYSTEM WIRING DETAIL ...................................... 17 DIAGRAM C – 1 WAY MULTIPLE ENTRANCE OVERVIEW CABLING................. 18 DIAGRAM D – 1 WAY MULTIPLE ENTRANCE WIRING DETAIL .......................... 19 DIAGRAM E – VIDEOPHONE AND EXTENSION WIRING ..................................... 20 DIAGRAM F – VIDEOPHONE LOCAL POWER WIRING........................................ 21 TROUBLESHOOTING.............................................................................................. 22 SPECIFICATIONS.................................................................................................... 24 IMPORTANT SAFETY INFORMATION ................................................................... 25 Model 840 PSU (with battery standby)............................................................... 25 Model PS4 and 340C Power Supplies............................................................... 25 Videophone........................................................................................................ 25 Installation and Operating Manual Page iii bellissimo 1 Way Video Entry System Introduction Description A bellissimo video door entry system consists of a door panel, positioned at the entrance of a building, a video telephone (videophone), placed inside of the building for the convenience of the occupant and a power supply and controller which are usually located inside an electrical cupboard. The door panel comprises of a twoway speech unit, a camera and a push button – which must be depressed by a visitor to initiate a call. The videophone, which rings in response, allows a two-way conversation via a handset whilst the caller can be observed through the integral display. The operator can selectively allow visitors access to the building by pressing a button on the videophone and so electrically releasing the door. The bellissimo 1-way Video Door Entry System is suitable for any building requiring a single push button at the entrance, such as houses, individual flats and offices. For multi-way systems please refer to “bellissimo 2-72-way Video Entry System” manual. The bellissimo “1-way” system is supplied with a dedicated door controller, which has been specifically optimised for “1-way” systems, ensuring simple installation. This basic system can support up to 3 extension videophones (more with additional PSU’s), whilst multiple entrances can be supported with the addition of one panel and one controller for each door. Main Features ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● CAT5 cable throughout; no co-ax required! 4” Flat screen display. High resolution CCD camera with infrared lamps. 12V d.c. Operation High quality full-duplex speech amplifier. Automatic picture display while ringing. Operator activated picture (CCTV mode) Ringer mute function. Fail safe or Fail secure lock releases and Magnetic locks. Lock release timer. Tradesman facility (optional). Facility for exit button and/or fire switch. Door ‘open’ indication. Second camera option. DDA panel options. Up to 3 Extension videophones. Multi-entrances supported. Installation and Operating Manual Page 1 of 25 bellissimo 1 Way Video Entry System Diagram 1: bellissimo Videophone View Mute Lock Contrast Button View / Camera select Mute on/off Lock Lamp Amber Red Green Steady Call in progress Videophone is muted Door is open Installation and Operating Manual Brightness Flashing There is a call Videophone is Off-Hook Press to release lock Page 2 of 25 bellissimo 1 Way Video Entry System Basic System Operation Call sequence When the push button is pressed at the entrance panel it causes the videophone to ring and the amber call lamp to flash. The videophone will continue to ring for up to 30 seconds or until the resident responds by picking up the handset. At this time the resident can freely converse with the visitor whose image is now displayed on the videophone; at the same time the green door lamp will flash to highlight the lock button. The call may be terminated by replacing the handset or more usually by pressing the lock button to allow the visitor access through the entrance; the speech and picture will persist for a further 3 seconds while the door is being released. Silent viewing When the videophone is ringing the resident can press the view button first instead of lifting up the handset; this will stop the videophone ringing and enable them to view the visitor for up to 60 seconds or until they press the lock button to release the door. Silent viewing can be ‘normalised’ at any time by picking up the handset and conversing with the visitor as described above. Auto Display When ‘Auto Display’ mode is selected the picture will come on while the videophone is ringing, otherwise the picture will only come on when the call is answered. Auto Display mode is usually pre-selected at installation and generally only one videophone will be set in this mode (see ‘Extension Videophones’ below). Call Mute The resident can mute the ringing sound in the videophone when they do not wish to be disturbed. Call mute is activated by pressing the mute button on the videophone, which then illuminates in red as a reminder. The handset must be on the hook for this to work. Pressing the mute button a second time will disengage the mute. During installation it is possible to set a time limit for the mute function in various values from 2 minutes up to 10 hours. When this time period has elapsed the mute will automatically disengage. (See ‘mute timer’, page 15). The mute feature can be set during installation to one of two modes (or disabled altogether): Ringer Mute only stops the audible ring, but the amber light will still flash and all other functions work normally. Ringer mute will continue for the preset time even if a call is answered. Pressing the mute button again while the videophone is idle will cancel mute. Full Mute prevents the videophone both from ringing or flashing the amber call lamp. Pressing the mute button again or lifting the handset will cancel full mute. Door Status Indication The green door lamp on the videophone will illuminate to warn the resident that a door has been left open following a call. This feature requires a door monitor contact to be fitted. Installation and Operating Manual Page 3 of 25 bellissimo 1 Way Video Entry System Call Privacy Once a call has been answered by one videophone no other videophones may join in, view or listen to the call. If another videophones handset is picked up the videophone will not activate; pressing the view button on another videophone will be ignored. User Activation (CCTV Mode) While the system is idle, pressing the view button will activate the system and display the picture at the entrance panel. Once activated, lifting the handset will enable speech at the entrance and the lock button may now be used to release the door or the user can hang-up. The picture will switch off after the preset talk-time. Second camera The Door Controller has the capability of driving a second ‘third party’ ‘CCTV’ camera, which is located nearby, and offering a different viewpoint. Pressing the ‘View/Camera’ button will alternate the view between the primary and secondary camera (if enabled). Extension Videophones Additional videophones may be added to the basic system. The number of extensions is limited only by power supply considerations. All videophones will ring when called however typically only the Master unit will display a picture while ringing. Once the master or extension videophone is ‘picked-up’ the picture will display on that unit alone. It should be noted that when the Master unit is left off-hook, extension videophones will not ring; the red light will flash on the Master as a warning of this condition. Lock Type and Operation The door controller supports both fail-secure and fail-safe locks including magnetic locks of up to 1A rating. The lock output is provided by relay contacts, which in the event of power failure are open. On pressing the lock button the lock timer will start and the door will unlock. The picture (and speech if active) will persist for the first 3 seconds of lock operation. For Lock Time settings see page 12. Exit Button and Fire Switch An input is provided for an exit button, which can be installed on the inside of the door and allow residents to exit freely. Momentary operation of this button will operate the lock release for the programmed lock time. A Fire switch or other override device may use the same input to hold the door open indefinitely. Trades Facility Use of a time clock in conjunction with a trades button will allow free access during the programmed time. Installation and Operating Manual Page 4 of 25 bellissimo 1 Way Video Entry System DDA Functionality A range of options exists for entrance panels, which meet the requirements of the Disability Discrimination Act (DDA) including Braille buttons and LED indicators. Contact your sales representative for further details. Multiple Entrances The bellissimo One-way System allows multiple entrances to be catered for by the addition of one door controller and one entrance panel for each entrance and in some instances additional power supplies. In a multiple entrance system an optional feature allows the resident to view the cameras at all the entrances with successive presses of the ‘camera select’ button. For details of this camera feature and user activation see the setting for ‘Camera Numbering’ on page13. Installation and Operating Manual Page 5 of 25 bellissimo 1 Way Video Entry System Design Considerations Equipment List A BS1 one-way bellissimo Video Kit comprises the following: Model No 1 x BS 1 x BSP1 1 x BSD1 1 x PS4 1 x 203 Description Videophone Standard or panel with a model 61 speech unit and Cam BV. Door controller. 4A 12V power supply. Fail-secure lock release For a Vandal Resistant Panel order a BS1/VR Kit Options For a 1 way system the following options are available: ● Extensions Model BS Videophone(s) ● Additional entrances, each comprising a BSD1 controller and BSP1 panel. (See also PSU requirements) ● Alternate lock releases, fail-safe and fail-secure ● Trades facility; specify BS1+TRBS; includes a model TS2000-BST time-clock ● Exit button. ● Battery back up PSU, Model 840 (12V 4A) ● DDA panels (Contact sales for further information) Entrance Panel Careful consideration should be given to the location of the entrance panel to ensure the best possible lighting conditions for the camera. In general strong back lighting of the subject (by the sun and sky) should be avoided, as the contrast between foreground and background may be too great for the camera. The field of view should contain as little of the sky as possible, particularly if south facing. If a backlit situation is unavoidable, additional lighting may be necessary to illuminate the caller and avoid a dark outline image (silhouette). Door Controller The door controller and PSU should be wall-mounted in a convenient cupboard or other protected environment with available mains power. Cable length to the entrance should be less than 50m. The door controller for the second and subsequent entrances may be situated in the same location, or to meet the 50m requirement may be situated in another location. Power supplies may be shared between door controllers placed in the same location, but controllers in separate locations should be separately powered. Installation and Operating Manual Page 6 of 25 bellissimo 1 Way Video Entry System Power Supply Requirements The system is powered by 12V PSU’s only: PS4 12V, 4A 340C 12V, 1.5A Optional for extensions Note 1. The 28V refered to on the videophone, door controller and wiring diagrams is internally generated in the controller. DO NOT use any PSU other than 12V or damage may occur. Note 2. The PS4 power Supply has been specifically designed to operate with the high-surge requirements of the system. Bell Systems are unable to guarantee functionality or provide support for systems which use third party power supplies. Exact power supply requirements depend upon many factors. The number of power supplies included within a standard ‘kit’ assumes that all controllers are installed in one location and that there are no extensions. The following table is a guide: (Please contact Technical support for other variations) System Power Supplies BS1 Kit 1 x PS4 BS1 & 3 Extension videophones 1 x PS4 (No auto display) BS1 & 3 Extension videophones 1 x PS4 (All with auto display) 3 x 340C 2 Door one-way system 1 x PS4 3 Door one-way system 2 x PS4 Comments Supplied in kit Only the Master videophone will have auto display A 340C will supply each of the extension videophones Both BSD1 door controllers must be in the same location 2 BSD1 door controllers per PS4 power supply Assumes maximum Lock Release current of 1A Cable Specification. All system wiring must be carried out using CAT5 signal cable and where necessary 1mm² (or greater) power cable as tabulated below. CAT5 cable has a known performance for the transmission of video signals, whilst telephone or alarm cables are not suitable. Bell Systems will be unable to offer any warranty or support for systems installed using incorrect cables. Installation and Operating Manual Page 7 of 25 bellissimo 1 Way Video Entry System CAT5 cable CAT5 is our short reference for EIA standard UTP Category 5 Unshielded Twisted Pair data cable. This is a standard solid core twisted pair cable having 4 pairs (8– cores) and no shield. The cores are in pairs where Blue and ‘Blue with a White stripe’ are twisted together as the first pair. The other three pairs are similar with main colours Orange, Green and Brown. · Also available and acceptable are: UTP Category 5e (CAT5e) UTP Category 6 (CAT6) UTP Category 6e (CAT6e) The exact cable can be chosen from the above on cost and availability grounds. · · STP (Shielded Twisted Pair) cables are not recommended. UTP patch cables are not recommended. NOTE: CAT5 cable is easily identifiable as it has its specification printed on the sheath Cable Distances (refer to diagrams A and C) Door Controller to Videophone System Distance Cable Comments System with single < 75m 1 x CAT5 videophone < 300m 1 x CAT5 2 x 1mm2 System with 3 Extension < 50m 1 x CAT5 Only Master videophone has videophones: ‘Auto display’ Single PS4 power supply System with 3 Extension < 300m 1 x CAT5 All videophones have Auto 2 videophones: display <5m 2 x 1mm Extensions each 1 x 340C each PSU 340C Panel to Door Controller All Systems, each entrance <50m 1 x CAT5 Basic Features only Lock Release up to 1A <10m ¼ x CAT5 <50m 2 x 1mm2 Option: Exit button <50m ¼ x CAT5 Option: Trades button <50m ¼ x CAT5 Requires a Time-clock Option: Door Monitor Switch <50m ¼ x CAT5 Power Supply to Door Controller All Systems, each PS4 to <3m 2 x 1mm2 BSD1 <5m 2 x 1.5mm2 NB. A CAT5 cable has 4-pairs (8 cores) For larger cable distances please contact manufacturer. Installation and Operating Manual Page 8 of 25 bellissimo 1 Way Video Entry System Installation & Commissioning The following checklist is a reminder of what is required. Refer to the relevant pages for further details. ● ● ● ● ● ● Review the section headed ‘Important Safety Information’. Ensure that ‘Design Considerations’ have been studied and understood. Confirm that CAT5 cable has been specified. Install the system according to instructions in this section. Check/set the Door Controller Dipswitch and Jumper settings. Check/set each Videophone Dipswitch settings. Installation and Operating Manual Page 9 of 25 bellissimo 1 Way Video Entry System Wiring Refer to Diagram B for single entrance systems and Diagram D for multi-entrances. All wiring is carried out using a mixture of CAT5 for the signal wiring and 1mm² (or greater) cores for the power wiring; refer to Page 8 for further details. It is strongly recommended that a consistent colour code be used throughout such as that indicated on the connection diagram. Certain signals must be interconnected using a twisted pair from the CAT5 cable. These are clearly marked on the connection diagram and should be strictly observed. Entrance Panel The panel should be mounted at an optimum height of 1.6 m, measured between the ground and the centre of the camera window. With flush mounting panels it is advisable to apply mastic to the top edge of the panel to prevent water ingress behind the panel. On construction sites the panel must be protected from corrosive substances such as ‘brick acid’. The panel should be cleaned only with a damp cloth containing dilute detergent. Videophone The Videophone is designed to be wall mounted onto plasterboard or other masonry at an optimum height of 1.6m. It should be fixed with three No 8 screws (not supplied). Use the template included with the videophone to mark out the drilling positions, and drill the three holes and insert the appropriate wall plugs. If the cable is to be feed from the wall cavity then make a hole for this at the same time. Fit the top two screws but do not fully tighten. Now remove the top cover of the videophone, which is secured by clips at both sides. If top or bottom cable entries are required, careful remove the appropriate cutout with side snips taking care not to damage any internal components. Hang the videophone on the two screws already fitted allowing the cable (if present) to feed through and the third screw to be inserted at the bottom. Tighten all three screws. Before replacing the Front Cover remove the protective film from the display lens and also check that the DipSwitch settings are correct or change as necessary (see Page 15). Electric Door Release Both fail-secure and fail-safe lock releases (inc. magnetic locks) use the same terminals. To set the lock type, refer to the “Door Controller Switch” settings. When installing lock releases please allow a little movement on the door, as operation will be impaired if fitted too tight. NB. Magnetic locks (maglocks) must be fitted with a suppressor at the lock terminals. Some manufacturers fit an acceptable internal suppressor. Exit Button Input This input is for a normally open push button. ‘Exit +’ is the input and ‘Exit –’ is internally connected to 0V. Door Open Switch This switch can have closed contacts when the door is open or open contacts when the door is open. Dip SW2-5 sets the choice. The default of ‘contacts closed when door open’ must be selected when this feature is not required. Installation and Operating Manual Page 10 of 25 bellissimo 1 Way Video Entry System BSD1 Door Controller Settings BSD1 Door Controller Switch Settings Talking Time/Videophone Active DIP SW1 (1-4) Talk Time 15s 20s 30s 45s 60s 75s 90s 120s 150s 180s 60s 60s* SW1 SW2 SW3 (ASDFGHJK) (ASDFGHJK) (QWERGHJK) 4 3 2 1 On On On On On On On Off On On Off On On On Off Off On Off On On On Off On Off On Off Off On On Off Off Off Off On On On Off On On Off Other settings Off Off Off Off OFF ↔ ON * Default setting Ringing Time/Call Time and Ring Effect DIP SW1 (5-8) 7 On On On On Off Off Off Off On On On On Off Off Off Off 6 On On Off Off On On Off Off On On Off Off On On Off Off 5 On Off On Off On Off On Off On Off On Off On Off On Off Call Time 5s 8s 10s 15s 20s 30s 40s 45s 50s 60s 30s¹ 30s¹ 30s¹ 30s¹ 30s¹ 30s* Ring Cadence or Sound Effect 1 in 3 – 1 ring every 3 seconds 1 in 3 – 1 ring every 3 seconds 1 in 3 – 1 ring every 3 seconds 1 in 3 – 1 ring every 3 seconds 1 in 3 – 1 ring every 3 seconds 1 in 3 – 1 ring every 3 seconds 1 in 3 – 1 ring every 3 seconds 1 in 3 – 1 ring every 3 seconds 1 in 3 – 1 ring every 3 seconds 1 in 3 – 1 ring every 3 seconds 1 in 3 (Reserved For future use) 1 in 3 (Reserved For future use) 2 in 15 – 2 rings, 15S silence, repeat 1 in 15 – 1 ring, 15S silence, repeat 1 in 5 – 1 ring every 5 seconds 1 in 3* – 1 ring every 3 seconds SW1 SW2 SW3 (ASDFGHJK) (ASDFGHJK) (ASDFTYUI) 8 On On On On On On On On Off Off Off Off Off Off Off Off OFF ↔ ON * Default setting ¹ BS videophones build 3 and above; Build 1&2 videophones: 1 ring every 2 seconds. Installation and Operating Manual Page 11 of 25 bellissimo 1 Way Video Entry System Lock Operate Time Dip SW2 (1-3) 2 On On Off Off On On Off Off 1 On Off On Off On Off On Off Lock Time 3s* 4s 5s 6s 8s 10s 15s 20s SW1 SW2 SW3 (ASDFGHJK) (123FGHJK) (ASDFGHJK) 3 On On On On Off Off Off Off OFF ↔ ON * Default setting Individual Functions DIP SW2 (4-8) SW1 SW2 SW3 (ASDFGHJK) (ASDRTYUI) (ASDFGHJK) OFF ↔ ON SW2-4 Lock Type *Off Fail secure lock Lock behaviour during power failure Requires alternate mechanical means, key or thumb-turn to open on power failure On Fail safe lock Lock opens on power failure SW2-5 Door Status Switch Monitors doors left open From *Off Contacts Open when The default allows for no switch fitted build 2 Door is Closed onwards On Contacts Closed when Standard normally closed switch Door is Closed SW2-6 Camera 2 How many cameras at this door From build 2 *Off Camera 1 only Default – single camera per door onwards On Enable Camera 2 Second camera at the door SW2-7 View Function Camera action when view button pressed *Off Local View View button only selects the camera(s) at this From build 3 door On Global View View button sequentially selects all cameras onwards (See DIP SW3 below) at doors with this switch set SW2-8 View User Activated View button pressed when system is idle *Off Disabled View button only works when called from the From build 3 panel onwards On Enabled User can activate the system and look See DIP SW3 below to see anyone near the door(s) * Default setting Installation and Operating Manual Page 12 of 25 bellissimo 1 Way Video Entry System Camera Numbering DIP SW3 (1-8) SW1 SW2 SW3 (QWERTYUI) (ASDFGHJK) (ASDFGHJK) Camera 1 at this door Last Camera 4 3 2 1 Number 8 7 6 5 Number On On On On 1 On On On On 1 On On On Off 2 On On On Off 2 On On Off On 3 agama On On Off On 3 On On Off Off 4 On On Off Off 4 On Off On On 5 On Off On On 5 On Off On Off 6 On Off On Off 6 On Off Off On 7 On Off Off On 7 On Off Off Off 8 On Off Off Off 8 Off On On On 9 Off On On On 9 Off On On Off 10 Off On On Off 10 Off On Off On 11 Off On Off On 11 Off On Off Off 12 Off On Off Off 12 Off Off On On 13 Off Off On On 13 Off Off On Off 14 Off Off On Off 14 Off Off Off On 15 Off Off Off On 15 Off Off Off Off *16 Off Off Off Off *16 OFF ↔ ON * Default setting View Activated by User If ‘view activated by user’ is enabled, then one door controller must have SW3 1-4 set as camera 1. Camera 1 at this entrance will then be the first camera to be viewed. ‘Global View’ at Multiple Entrances If ‘Global View’ is enabled, successive presses of the view button will enable all entrance to be viewed in turn, including any second cameras, if enabled. Setting up the door controllers to enable ‘Global View’ requires careful setting of the switches. Not all entrances have to participate in ‘Global View’, and these entrances should remain set to ‘Local View’. The participating entrances must each be designated with a unique address 1, 2, 3, …etc in the required viewing sequence. NB the sequence must start with 1; the maximum is 16. If Camera 2 is enabled on any entrance then it will adopt the entrance address setting plus 1; the next entrance must skip that address. Each controller must also record the last camera number in the sequence – this will be the same setting for all entrances. Below are a couple of examples and a blank table for your use. Installation and Operating Manual Page 13 of 25 bellissimo 1 Way Video Entry System Example 1: Entrance Cameras at number this entrance 1 2 2 1 3 2 Example 2: Entrance Cameras at this entrance 1 1 2 2 First Camera DIP SW3 (1-4) 1 3 4 Last Camera DIP SW3 (5-8) 5 5 5 First Camera DIP SW3 (1-4) 1 2 Last Camera DIP SW3 (5-8) 3 3 Customer’s setup: Entrance Cameras at First Camera Last Camera this entrance DIP SW3 (1-4) DIP SW3 (5-8) 1 2 3 4 5 6 7 8 9 10 11 12 BSD1 Door Controller Jumper Settings The “Video Gain” jumper on door controllers should always be set to “Low” unless directed by Bell System Technical. This jumper is only required on some systems with very long camera to videophone cable runs well in excess of 150m. Use of this jumper with short runs will cause picture problems. Installation and Operating Manual Page 14 of 25 bellissimo 1 Way Video Entry System BS Videophone Switch Settings Mute Time Setting SW1 (1-4) 3 On On On On Off Off Off Off On On On On Off Off Off Off 2 On On Off Off On On Off Off On On Off Off On On Off Off 1 On Off On Off On Off On Off On Off On Off On Off On Off Mute Time Disabled¹ 2 minutes 5 minutes 10 minutes 15 minutes 20 minutes 30 minutes 45 minutes 1 hour 2 hours 4 hours 5 hours 6 hours 8 hours 10 hours *Indefinite² SW1 (QWEFGHJK) 4 On On On On On On On On Off Off Off Off Off Off Off Off OFF ↔ ON * Default setting ¹Disabled means pressing the mute button has no effect. ²Indefinite; the mute is cancelled by pressing the button again. (ASDRTYU8) Individual Functions DIP SW1 (5-8) SW1 OFF ↔ ON SW1-5 Master / Slave *Off Master videophone On Slave videophone / Extension SW1-6 Auto Display on Ring *Off Display During Ring On No Display During Ring SW1-7 Mute Function *Off Ringer Mute Only On Disable Videophone SW1-8 Video Terminator Off No Termination *On Terminate – Last Videophone Extension videophones are slaves Single videophone or one in daisy-chain is master8 Extra videophones per call or flat Caller visible while ringing Yes No Action of mute button No sound, Visible ring – view flashes, picture if enabled Same as leaving off hook but steady not flashing button Prevents cable reflections Daisy-chained videophones not at end of cable Must be on in videophone at end of cable * Default setting Installation and Operating Manual Page 15 of 25 bell issim o 1 W ay V ideo Entry S ystem Diagram A – 1 Way Basic System Overview Cabling All cable MUST be bellissimo Cat 5 4 pair data cable. Except for power wiring where stated. 75m Max (1 phone) Cat 5 (For over 75m or extension phones see diagrams E&F) 2m Max BSD1 1 way Door Controller Cat 5 2 x 1mm² 50m Max Cat 5 (Options) Lock wiring options Lock 0.5A 1.0A 12m 1 pair 1 pair 25m 1 pair 2 pair 50m 2 pair 4 pair 50m 2x1mm² 2x1mm² Entrance Options Exit button 1pair Door monitor 1 pair Trades 1 pair 1 button panel PSU PS4 12V Lock release Installation and operating manual Page 16 of 25 bell issim o 1 W a y V ideo En try S ystem Diagram B – 1 Way Basic System Wiring Detail BS Bellissimo Video Phone 28V Data Audio Video + - A B 1 2 + - + - M S Camera 1 + - M S Camera 2 Camera Inputs - + 2 1 B A - - + 2 1 B A Video Audio Data Commn Video Audio Data Cat 5 Input Cat 5 Output Control Equipment Area - + 28V Monitor Power 230V Mains + BSD1 Door Controller (1 Way) PS4 Power Supply 12V + CO NO Door Panel Speech Unit Panel Misc. C R O T B1 B2 LS LL LC Entrance Power Supply Exit Door Lock + - + - + - 12V 12V + - + - N L E TS2000 Time Clock NC 2 x 1mm² Door Panel Call CAM-BS M S Camera 1 (Optional Link For Infra Red) + Lock wiring options Lock 0.5A 1.0A 12m 1 pair 1 pair 25m 1 pair 2 pair 50m 2 pair 4 pair 50m 2x1mm² 2x1mm² All cable MUST be Cat 5 4 pair data cable. Except for power wiring where stated. C H Speech Unit R 51/61 O T _ + _ Trades Button (optional) Exit button or Door Monitor Fire Switch Switch (optional) (optional) Installation and operating manual Lock Page 17 of 25 bell issim o 1 W ay V ideo E ntry S ystem Diagram C – 1 Way Multiple Entrance Overview Cabling All cable MUST be bellissimo Cat 5 4 pair data cable. Except for power wiring where stated. 75m Max (1 phone) (For over 75m or extension phones see diagrams E&F) Further Entrances PSU PS4 12V Cat 5 2 Cat 5 BSD1 1 way Door Controller BSD1 1 way Door Controller 2 PSU PS4 12V Control equipment Entrance Options Exit button 1pair Door monitor 1 pair Trades 1 pair (Options) (Options) Cat 5 Cat 5 Up to 50m Lock wiring options Lock 0.5A 1.0A 12m 1 pair 1 pair 25m 1 pair 2 pair 50m 2 pair 4 pair 50m 2x1mm² 2x1mm² Entrance 1 Lock release Entrance 2 Installation and operating manual Lock release Page 18 of 25 Diagram D – 1 Way Multiple Entrance Wiring Detail bell issim o 1 W ay V ideo E ntry S ystem Installation and operating manual Lock wiring options Lock 0.5A 1.0A 12m 1 pair 1 pair 25m 1 pair 2 pair 50m 2 pair 4 pair 50m 2x1mm² 2x1mm² Except for power wiring where stated. 4 pair data cable. Cat 5 All cable MUST be Page 19 of 25 bell issim o 1 W ay V ideo E ntry S ystem Diagram E –Videophone and Extension Wiring The 75m Cat 5 limit is only for a single phone powered by a controller For longer runs or extension phones additional power cores will normally be required Master bellissimo 1 Cat 5 Plus Power Cores Extension bellissimo Extension Extension bellissimo bellissimo Phones MUST be "daisy chain" wired. Only one phone must select "auto display". Installation and operating manual Page 20 of 26 bell issim o 1 W ay V ideo E ntry S ystem Diagram F – Videophone Local Power Wiring Where more than one extension phone is required to provide "auto display" then additional power supplies will be required Master bellissimo Extension Extension Extension bellissimo bellissimo bellissimo PSU 340C 12V PSU 340C 12V PSU 340C 12V 1 Cat 5 Installation and operating manual Page 21 of 26 bellissimo 1 Way Video Entry System Troubleshooting Power Problems Videophone resetting (All three indicators lights come on at once and then go off). 28V LED does not light on controller. PS4 output voltage fluctuating, meter reading unstable. Video Problems Blank picture when: Calling videophone/ Pressing view No picture when calling videophone No picture when pressing view Repeated pressing of view does not select cameras in sequence as expected. Power supply intermittent short or overload. More than 1 extension enabled for auto display. Lock output short-circuit; see ‘Lock Problems’ · Temporarily remove connection to 28V+ output. · · Output overload is causing current limit to operate See Lock Problems below · · · · Broken or missing Video + or Video – wire. Cameras incorrectly configured refer to SW2-6 Call is from an audio only panel. Check Auto display switch is on. See page 15 · · · · Another videophone in use SW2-8 not set to ‘Enable’ No entrance has SW3 1-4 set to 1 (all ON) Check SW2-6 at all entrances is set for correct number of cameras at that entrance Check settings for SW3 if SW2-7 is enabled See section ‘Global View’ on page 13 Power supply voltage low. Terminator switch not set on last videophone. Too many terminator switches set on. Video gain jumper set to high on a short run. Very bright area in background upsetting camera. Power not connected to camera IR night illumination. Connect 1 to + on camera. · · · · · · · Unstable picture · Entrance cannot be seen at night Speech Problems Loud tone at the entrance speaker. (Acoustic feedback) No speech from videophone to entrance No speech from entrance to videophone · · · · · · · · · · · Volume controls set too high Broken Audio 1 or 2 wire in the cabling. Intermittent or broken wire in Data A or B. Videophone has reset; see power faults. Missing R core to door controller Broken Audio 1 or 2 connections. Missing T core to door controller Broken Audio 1 or 2 connections. Installation and Operating Manual Page 22 of 25 bellissimo 1 Way Video Entry System Call Problems Videophone does not ring or flash when called · · · · · No extension videophone rings or flashes when called Videophone off hook or muted on full mute. No power to videophone; check that red lamp flashes when handset is picked up. Data wiring has a fault, Data A or B broken. 0V to controller missing on separately powered videophone. Master videophone off hook or muted on full mute. Lock Release Problems Lock release does not operate è è TEST: · Press ‘Test’ Button on Door Controller (when system idle): · · Lock release operates all the time or in reverse Confirm ‘LOCK’ LED illuminates for 3 seconds Check Output Voltage at LOCK terminals Connections to Lock Release are open or shorted Voltage drop due to insufficient cable capacity Lock current is too high; Power supply is resetting · Check fail safe/fail secure SW2-4 selection matches the lock type. Installation and Operating Manual Page 23 of 25 bellissimo 1 Way Video Entry System Specifications BS Videophone Size Fixing Supply Voltage Current Consumption Buzzer Mute Time PS4 Power Supply Size Output Voltage (regulated) Output Current Mains Supply Internal Fuse Supply Voltage Temperature Range Model 61 Speech Unit Size Supply Voltage Current consumption Model CAMBS Camera Size Supply Voltage 210mm x 260mm x 60mm Wall Mounted 13.5V minimum – local power supply only. 20V to 28V typical 750mA @ 13.5V active 28mA @28V idle Disabled, 1minute through 10 hours, indefinite 236mm x 105mm x 81mm 13.5V d.c. minimum 13.8V d.c. nominal 14.1V d.c. maximum 3A continuous 4A peak (5 minutes max) Not user replaceable 230V 50Hz nominal 0 ºC to 50 ºC 98mm x 60mm x 24mm 10V d.c. minimum 15V d.c. maximum 100mA d.c. maximum Image Device Sensitivity Minimum Focus Viewing Angle 60mm x 57mm x 31mm 10V d.c. minimum 15V d.c. maximum 175mA maximum without IR 215mA maximum with IR (Link 1 to +) 1/3” CCD 0.1 lux 100mm 92º (typical) BSD1 Door controller Size Supply Voltage Current Consumption 185mm x 230mm x 42mm 10.8V min, 13.8V typical, 15V max 150mA idle @13.8V with 1 videophone Current consumption Installation and Operating Manual Page 24 of 25 bellissimo 1 Way Video Entry System Important Safety Information Connections to the 240VAC mains supply must be carried out by a qualified electrician or similar competent person, and made in accordance with current legislative requirements. A two-pole switch (as provided by a Consumer Unit or Switch-Fuse) must be included to isolate both Live and Neutral during Installation or Maintenance. The circuit must be protected by a fuse or other current-limiting device, rated according to the capacity of the cable used, up to a maximum of 10A. Use only mains cable to BS6004 or equivalent, within the following specified limits: Min Max Conductor Diameter 1.0mm (0.8mm2) 2.25mm (4mm2) Cable Diameter 4.0mm 8.0mm Model 840 PSU (with battery standby) The Model 840 PSU must be placed in a protected indoor environment such as an electrical cupboard. It must be secured to the wall with adequate fixings so that there is no possibility of it falling. The Lead-Acid Battery for the Standby Power Supply is shipped in separate packaging. It should only be connected once the system has been fully tested. Connection is made by 2 leads with spade terminals; observe the correct polarity - red to positive, black to negative. Care must be taken to ensure that the terminals of the battery are not shorted together by metal objects, as this may constitute a Fire Hazard. The Control Cabinet is IP55 rated (to exclude dust) and is vented to avoid the build-up of gases. Do not block any vents that may be apparent. A good mains safety earth must be connected to the cabinet housing the power supply Where the power supply is fitted with a replaceable internal mains fuse and or battery fuse, always replace with the same type as indicated on the power supply. The fuse must be approved to BS EN 60127 or equivalent. Power Supply Model Mains Fuse (Time Delay) Battery Fuse (Quick Blow) 840 T2A 20mm HBC (HRC) Ceramic F4A 20mm Glass Model PS4 and 340C Power Supplies These power supplies must be wall-mounted onto plasterboard, or a similar nonconductive material, in a protected indoor environment such as an electrical cupboard. When fitting the power supply cable (both mains and low voltage) ensure the cable entry cut-outs in the enclosure lid are no larger than necessary for the cable diameter used and under no circumstances must they be taken beyond the outer cut-out zones. Videophone The display module of the videophone has a high voltage circuit (2KV), which represents a shock hazard. Do not remove the inner cover of the videophone assembly, there are no user adjustments requiring this. Installation and Operating Manual Page 25 of 25