Download Casablanca Seacoast Owner`s manual
Transcript
OWNER’S MANUAL READ AND SAVE THESE INSTRUCTIONS! SAFETY FIRST: Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation. Therefore, before attempting to install and operate your Casablanca fan, read this Owner’s Manual completely and carefully. Retain the manual for future reference CONTENTS INTRODUCTION Before You Start Safe Use 2 2 MOUNTING RECOMMENDATIONS General Guidelines ......................................................................................................................................................... 3 Sloped Ceiling Installations ............................................................................................................................................ 3 FAN INSTALLATION Getting Started ............................................................................................................................................................... 4 Crossbar Mounting Bracket Installation ......................................................................................................................... 4 Lag Screw Installation .................................................................................................................................................... 5 Canopy Installation ......................................................................................................................................................... 5 Fan Preparation ............................................................................................................................................................... 6 Blade Installation ............................................................................................................................................................ 7 Switch Housing Bracket / Cap Installation .................................................................................................................... 8 Hanging the Fan ............................................................................................................................................................. 9 Canopy Electrical Connections ....................................................................................................................................... 8 Canopy Hatch Installation .............................................................................................................................................. 8 VERSA•TOUCH2™ CONTROL Control Bracket Installation .......................................................................................................................................... 10 Remote Operation......................................................................................................................................................... 11 Changing Transmitter Frequency Setting ..................................................................................................................... 11 TROUBLESHOOTING TIPS .......................................................................................................................................... 12 CARE RECOMMENDATIONS ...................................................................................................................................... 13 AUTHORIZED SERVICE CENTERS ........................................................................................................................... 14 PRODUCT SPECIFICATIONS....................................................................................................................................... 16 ASSEMBLY DIAGRAM ................................................................................................................................................... 17 C343010 AA1005 1 INTRODUCTION BEFORE YOU START • CAUTION: Risk of electrical shock! All wiring must be in accordance with the National Electric Codes and the appropriate local electrical codes. The National Codes require proper grounding as a precaution against electrical shock. A qualified electrician should be consulted if you are unsure. • This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan installations, if it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling installations. • This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum current requirement for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts. Maximum light current is 2.8 amps or 340 watts of lighting. • Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make sure all wires are within the canopy and that no wires are being pinched. Unpacking Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed in the Parts List. Before discarding packaging material, be certain that all parts have been removed. NOTE: For best performance and for your warranty to be valid, use only genuine Casablanca Fan Company blades, light fixtures, and accessories. SAFE USE • Inspect the contents of your carton for possible shipping or handling damage and report any such damage directly to your authorized Casablanca dealer. • It is always a good idea to have an assistant to help with the installation. • The blades in each pack are matched for equal weight to assure smooth fan operation. If more than one fan is being installed, be careful not to mix blades from different cartons. • Never install a fan over a pool or spa. • For safety reasons, the fan blades must be a minimum of 7 feet above the floor. • In any installation, the tips of the blades must be at least 18 inches from the wall in order to provide sufficient clearance for the blades. • Never insert anything into the path of the fan blades while the fan is in operation. • When cleaning, painting, or working near your fan, be very careful of the fan and blades. Always turn the power OFF to the ceiling fan before servicing it, working on it, or replacing lightbulbs. • Never operate a fan that has been damaged in any way. For assistance in obtaining service, call Casablanca Fan Company toll-free at 1-888-335-5247 or contact your local Casablanca Authorized Dealer. 2 FUSE BOX CIRCUIT BREAKER Remove the fuse for the circuit you will be working on Trip the breaker for the circuit you will be working on 18ʺ 84ʺ MOUNTING RECOMMENDATIONS GENERAL GUIDELINES Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mounting recommendations as you decide where to install your Casablanca fan. • This fan requires a minimum ceiling height of 9 feet. • Do not locate the fan in a doorway or above a swinging door. • In bedrooms, fans work best when mounted above the foot of the bed. • Over pool tables, be sure to provide plenty of clearance to avoid damage from pool cues. • In kitchens, be sure to allow for open cupboard doors to clear the fan blades. • Do not install a fan close to, or over, a pool or spa. High humidity combined with corrosive gases will destroy the finish and warp the blades. Fan Size Variable fan speed capability permits the use of a full-size 54-inch fan even in smaller rooms. For very large rooms, two fans may be needed. SLOPED CEILING INSTALLATIONS SUGGESTED EXTENSION POLE LENGTHS Ceiling Height Pole Length 8ʹ 0” 8ʹ 6” 9ʹ 0” 9ʹ 6” 10ʹ 0” 11ʹ 0” 12ʹ 0” 13ʹ 0” 14ʹ 0” standard standard 6” 12” 12” 18” 24” 36” 48” Extension Pole Maximum Angle 32º Blades must be a minimum of 7ʹ above the floor 7’ minimum When to Use Extension Poles For best performance and appearance, an extension pole should be used with your Casablanca fan when installing on high (cathedral) ceilings or sloped ceilings. Casablanca offers standard poles in increments of 6 inches up to 5 feet. Custom poles are available in lengths up to 9 feet 9 inches. See your Authorized Casablanca Dealer for details. NOTE: The fan may wobble or vibrate if the pole length is not long enough and the inside blade is too close to the downslope or side wall. Extending the pole length usually will solve the problem. Calculation of 32 Degrees Use the tear-off Ceiling Angle Template card inserted in this manual. It provides you with a simple “go” or “no go” for installing your fan on a sloped ceiling. EXAMPLE 1 This slope is less than 32 degrees. It is okay to install your fan. EXAMPLE 2 This slope is 32 degrees, the maximum slope that will allow the fan to hang straight down. It is okay to install your fan. EXAMPLE 3 This slope is more than 32 degrees.Your fan will not hang straight down; an adaptor is necessary. Contact your local Authorized Casablanca Dealer to purchase a “Sloped Ceiling Adaptor.” 3 FAN INSTALLATION GETTING STARTED Installing a New Ceiling Fixture Outlet Box If you do not have an existing fixture located where you wish to place your Casablanca fan, an approved ceiling fixture outlet box must be installed and wired. WARNING: To reduce the risk of fire, electrical shock, or personal injury, mount to outlet box marked “Acceptable for Ceiling Fan Support” using the mounting hardware provided with the outlet box. Using Existing Ceiling Fixture Outlet Box After turning the power OFF at its source (either the circuit breaker or fuse box), lower the old fixture and disconnect the wiring. Check the ceiling fixture outlet box to be sure that it is marked “Approved For Ceiling Fan Mounting.” If it is not, a new box must be installed. NOTE: The weight of this fan is 50 pounds. CROSSBAR MOUNTING BRACKET INSTALLATION CEILING HARDWARE (not to scale) ADDITIONAL HARDWARE Wire Nut (4) 21/4” x 8-32 Rounded Head Screw (2) 1” x 8-32 Rounded Head Screw (2) Crossbar Mounting Bracket Lag Screw NOTE: After removing the old fixture, check the outlet box to ensure it is supported by a joist or beam across its upper surface. If not, a 2 x 4 stud must be installed. Step 1a. Remove the knockout plug in the center of the outlet box or drill a 1/2-inch hole for the lag screw to pass through. Then drill a 1/4-inch guide hole into the joist or beam to a depth of 3 inches. Step 1b. Route the outlet box wires through the center hole of the crossbar mounting bracket. Attach the crossbar mounting bracket to the outlet box with the screws provided, ensuring that the outlet box wires are not pinched by the washer. / ” #7 x 5” (1) 3 8 4 Large Flat Washer 3/8”(1) Joist Ceiling-Fan-Approved Wiring Box Ceiling Wiring Crossbar Mounting Bracket Ridge side down Green Ground Wire CAUTION: To reduce the risk of personal injury, use only the mounting hardware provided with the approved outlet box to install the crossbar mounting bracket. WARNING! Support directly to building structure only. Flat Washer (2) APPROVED OUTLET BOX HARDWARE LAG SCREW INSTALLATION NOTE: We recommend that the ceiling box be of sufficient capacity to support the weight of the fan and light fixture under any conditions. Step 2. With the large washer attached, pass the lag screw through the center hole of the crossbar mounting bracket and screw into guide hole. Tighten until outlet box is mounted firmly to beam. This box must be secured to the ceiling firmly. Large Washer Lag Screw CANOPY INSTALLATION CANOPY HARDWARE (not to scale) Canopy Hatch Canopy Screw (4) Canopy Canopy Lock Washer (4) Step 3. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 2 1/2" long canopy screws and lock washers provided with your Casablanca fan. Tighten using the provided screwdriver until snug against the ceiling. NOTE: On sloped ceilings, align the canopy opening with the top or peak of the room. Feed outlet box wires through canopy opening Canopy Lock Washers Canopy Screws 5 FAN PREPARATION IMPORTANT SAFETY INFORMATION! Before starting the installation of your ceiling fan, install the threaded downrod into the motor coupling and lock the assembly Prepare for fan installation as follows: Step 4a. Place the motor cover on the downrod as shown. Perma•Lock™ Downrod and Ball Assembly Motor Wires Step 4b. Route the wires from the motor through the Perma•Lock™ downrod and ball assembly. Motor Cover Tip: The downrod has a tapered thread that is designed to lock completely when correctly installed. Step 4c. Using the provided Allen wrench, loosen the set screw several turns to allow installation of the downrod. Thread the downrod into the motor coupling until it stops turning. This will take at least four and a half full turns. Step 4d. Tighten the set screw securely with the provided Allen wrench to ensure safe operation of your fan. CAUTION: Failure to fully lock in the downrod before securely tightening the Allen set screw may cause the fan to separate from the downrod during normal operation! Step 4e. Slide the motor cover down so that it is flush against the top of the fan. Step 4f. Using the three provided screws, attach the motor cover to the motor. Tighten securely with the provided Phillips screwdriver. Allen Set Screw Motor Coupling Tapered Thread Step 4g. Unsnap one of the switch housing brackets on the bottom of the switch housing and set it aside for use in step 6c. Step 4h. To reach the blade holder mounting holes in the fan motor, the switch housing cap must be removed. Take out the two 8-323/8" screws securing the switch housing cap and set them aside for use in step 6c. Switch Housing Bracket Mount Screws 8-32 X 3/8" (2) 6 Switch Housing Cap BLADE INSTALLATION BLADE HARDWARE (not to scale) Blade Holder Blade Blade Holder Screw (2 per blade) Blade Screw and Washer Step 5a. Remove the five shipping blocks attached to the rotating motor plate using the provided Phillips screwdriver. Blade Screw and Washers (4 per blade) Step 5b. Attach each blade to a blade holder by first pressing the blade badge into the blade, then threading four blade screws into the screwholes and tightening using the screwdriver. Repeat for each blade assembly. Blade Blade Holder Step 5c. Attach each blade/bladeholder assembly to the motor by threading two blade holder screws through the matching holes in the blade holder and the motor. Using the screwdriver, tighten the screws loosely. After all five blade assemblies have been installed, tighten the screws securely using the screwdriver. Blade Holder Screws (2 per blade) 7 SWITCH HOUSING BRACKET/ CAP INSTALLATION SWITCH HOUSING BRACKET/CAP HARDWARE (not to scale) Switch Housing Cap Switch Housing Bracket (2) Step 6a. Take the two switch housing bracket you removed in step 4g and snap it into the holes in the switch housing. This is to prevent any wires getting pushed down near the motor. Make sure no wires are in the way or pinched in these NOTE: If you have purchased an accessory light fixture for this fan, please refer to the instructions included with the light fixture. If not, continue with Step 6b. Step 6b. Line up the two clearance holes in the cap with the two threaded holes on the raised rim of the switch housing. Press the cap onto the switch housing to seat the guide pins into the alignment holes of the switch housing. Step 6c. Using the two 8-323/8ʺ screws removed in Step 4h, install the cap onto the switch housing. Tighten the screws securely using the Phillips screwdriver. 8 Switch Housing Mount Screw (Removed in Step 10) 8-32 X 3/8 (2) HANGING THE FAN Step 7a. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening. Check that no wires were pinched. Rotate the fan body until the slot in the ball fits into the pin opposite the canopy opening. Step 7b. Trim excess motor wires, leaving at least 6 inches above the downrod. Strip 1/2-inch insulation from the end of each wire using a wire stripper (available at your local hardware store). Ball Slot Pin CANOPY ELECTRICAL CONNECTIONS Step 8. Attach the fan wires to the ceiling fixture outlet box wiring by placing the bare ends of the wires side by side and then securing with a wire nut. Test that the connection is secure by pulling on the wire nut. Connect in this order: • GREEN leads from mounting plate and downrod assembly of fan to GROUND conductor of power source. Secure with wire nut. • WHITE wire from fan to white NEUTRAL wire in ceiling fixture outlet box. Secure with wire nut. • BLACK power wire from fan to BLACK power wire in ceiling outlet box. Secure with wire nut Wire Nut 2 Black Wires 2 White Wires 3 Green Wires NOTE: If the color of your ceiling wires differs from that described, consult an electrician. CANOPY HATCH INSTALLATION Step 9a. Tuck the wires into the canopy with the wire nuts pointed upwards so that the WHITE and BLACK wires are on opposite sides of the canopy and all wires are clear of the canopy opening. Step 9b. Install the canopy hatch with the last canopy screw and lock washer using the provided Phillips screwdriver. To do this, tilt the fan body away from the hatch opening. Tighten the screws firmly. Step 9c. Straighten the fan, then check to ensure that there is no movement between the canopy and the ceiling or the Perma•Lock™ downrod and the ball assembly. Canopy Hatch Canopy Washer Canopy Screw Tilt away from hatch opening 9 VERSA•TOUCH2™ INSTALLATION VERSA•TOUCH2™ INSTALLATION HARDWARE (not to scale) W-73 Control Holder W-73 12v Battery Drywall Anchor 6-32 (2) Wood Screw 1" (2) Screw 6-32 X 3/8" (2) Screw 6-32 X 1" (2) CONTROL BRACKET INSTALLATION SAFETY FIRST: To reduce the risk of electrical shock, this fan must be installed with an isolating wall control/switch. CAUTION! Do not use with wall dimmer. Rocker Type Light Switch Tabs Standard Toggle Switch Inner Mounting Holes Outer Mounting Holes Switch Cover Plate Control Bracket Standard Light Switch Step a. Remove the two screws holding the switch cover plate. Do not remove the cover plate. Step b. Orient the control bracket as shown and line up the two inner mounting holes with those on the switch. Step C. Install and tighten screws using the provided Phillips screwdriver. Wall Installation Step a. Locate a 2x4 wall stud in a convenient location. Step b. Orient the control bracket as shown over the 2x4 stud. Step C. Use the 1" wood screws in either the inner or outer mounting holes. Install and tighten screws using the provided Phillips screwdriver. 10 Switch Cover Plate Control Bracket Rocker Light Switch Step A. Break off the two tabs by pushing outward. Step B. Remove the two screws holding the switch cover plate. Do not remove the cover plate. Step C. Orient the control bracket as shown and line up the two inner mounting holes with those on the switch. Step D. Install and tighten screws removed in Step B by hand only. NOTE: The wall anchors and 6-32 x 1" screws may be used in situations where mounting to a stud is not possible. Use the inner mounting holes. After securing the anchor, discard the anchor’s pointed screws and use the 6-32 decor ovalhead screws supplied. Anchor Panhead Screw Wood Screw 1" Drywall Anchor Decor Ovalhead Screw 6-32 X 1" REMOTE OPERATION Fan Control To start the fan. Press the selected speed button to run the fan at the desired speed. 1=Low speed 2=Medium speed 3=High speed To turn off the fan. Press the FAN OFF button. Airflow Direction To reverse the airflow press the REVERSE button. Reverse operates at any speed whether fan is on or off. The fan returns to its set speed after reversing. Light Control Turn the light on or off independently from the fan by pressing the UP LIGHT DOWN LIGHT OR BOTH button. (This is a rocker switch. Press the left side for the Down Light, right side for the Up light , and the middle for both.) Keep pressing the button in excess of 0.7 seconds, it becomes a dimmer. The light varies from ‘bright’ to ‘dim’ over approximately 8 seconds. This sequence will reverse the light when it reaches the brightest or dimmest level if you continue to hold the LIGHT button. Release the button when the desired level is reached. Auto Resume Quick (pressing less than 0.7 seconds) on/off operation of the LIGHT button maintains the desired brightness level set previously. Light Send Signal LED Up Light Down Light MED LOW HIGH Fan Off Reverse TRANSMITTER FREQUENCY SETTING Note: All fans leave the factory set to ‘00000’. You will only have to change the dip switch settings in the remote if you are using more than one fan in the same area and want to control them separately. Step 1. At the circuit breaker or fuse box, turn the power off for the fan you want to change. Step 2. Open the battery door of the Versa•Touch control and remove the battery. Step 3. Change the dip switch settings, assuring that they are different from the previously installed Versa•Touch fan. Step 4. Re-install the battery and the battery door on the control. Step 5. At the circuit breaker or fuse box, turn the power back on for the fan whose frequency you are changing. Step 6. Within 20 seconds of restoring power, push the Hi, Med, and Lo buttons (in that order). HELPFUL HINT: Label your controls to ensure you do not mix them up. WARNING: Do not turn the power off at the circuit breaker, then back on, for the previously installed Versa•Touch 2 fan(s), as you may inadvertantly change the frequency settings for it as well. versa•touch 2 control (back) Dip Switch Set to ‘10000’ Within 20 seconds of turning the fan on, press in this order to set new frequency: 3 - HIGH 2 - MED 1 - LOW LOW Dip Switch Set to ‘01001’ MEDIUM HIGH IF FAN DOES NOT WORK If the fan is not functioning after installation: 1. Check to make sure that batteries are installed correctly in the control. MED 2. Turn the power off to the fan (from the circuit breaker) for at least FIVE seconds. 3. Turn the power back on (at the circuit breaker) and push the High, Medium, and Low buttons–in that order–within 20 seconds. 4. The fan should now function properly. LO Circuit Breaker or Fuse Box HIGH press in this order to set new frequency: HIGH MED LOW 11 TROUBLESHOOTING TIPS Please refer to this guide before requesting service or contacting your dealer for assistance. PROBLEM POSSIBLE REMEDIES Fan will not start • Check the main circuit fuses, circuit breakers, and wall switch position. Check all wire connections. Make sure the power is turned off during this inspection. • The 9-pin connector is not making good contact. Check the 9-pin connector in the receiver mounted in the switch housing (see receiver diagram on page 11). • The battery is weak. Install a fresh battery. • The fan receiver is defective. Replace fan receiver. • Check the frequency setting: Turn the power off at the circuit breaker, only for the fan that is not functioning. Check that the jumper switches match in both the receiver and the transmitter. Fan wobbles or shakes excessively • Be sure the canopy pin is set properly into the slot on the ball. • Check that the bladeholders have not been bent during installation and the blades are balanced. • The hanger bracket and/or ceiling outlet are attached too loosely. Make sure the hanger bracket is attached tightly to the ceiling outlet box and the downrod assembly is secured firmly. • The downrod is attached to downrod base too loosely. Make sure all the screws are securely tightened. Fan is noisy during operation • Check and tighten the light fixture retaining screws, glass shade screws, and/or lightbulb(s). • Tighten the canopy screws and mounting plate assembly. Make sure the wire nuts inside the canopy and switch housing are not touching the metal parts and that they have not fallen off the wire splices. Tighten as necessary. • Tighten the blade holders to the flywheel (or direct drive motor) and the blades to the bladeholder screws. • Make sure all screws in the motor housing are snug but not overly tight. Fan does not run on low speed • If fan is new, it may need to be “broken in.” Run at high speed for several days. Battery life is short • Replace with alkaline batteries. Light works, but fan does not work • The 9-pin connector is not making good contact. Check the 9-pin connector receiver mounted in the switch housing (see receiver diagram on page 11). Fan and light run only on full speed • The fan receiver is defective. Replace fan receiver. Fan is missing one speed • The fan receiver is defective. Replace fan receiver. Fan does not change speed, but light works • The fan receiver is defective. Replace fan receiver. Reverse does not work • The fan receiver is defective. Replace fan receiver. Fan starts working by itself • There is frequency interference. Change frequency as described on Page 11. Fan operates only when transmitter is close • Check that antenna wire is not touching metal plate. Fan works, but light does not dim • The fan receiver is defective. Replace fan receiver. Fan works, but light does not work • The fan receiver is defective. Replace fan receiver. • The light socket is broken. Replace socket. • A lightbulb is defective. Replace lightbulb. 12 CARE RECOMMENDATIONS Fan Finishes • For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. • A vacuum cleaner brush nozzle can remove heavier dust. • Surface smudges or an accumulation of dirt and dust can be removed easily by using a mild detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents as these will damage the finish. Blades • Wood-finish blades should be cleaned with a furniture polishing cloth. Occasionally, a light coat of furniture polish may be applied for added protection and beauty. • For painted and high-gloss blades, surface smudges or an accumulation of dirt and dust can be removed easily by using a mild detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents as these will damage the finish. No Need for Lubrication • Never lubricate this fan! The precision motor at the heart of your Casablanca fan features sealed bearings that are lubricated for life. • Do not attempt to oil the motor. Changing Lightbulbs • Be sure to turn the power to OFF at the wall switch or circuit breaker before changing lightbulbs. • Replace bulbs with the same type as you removed from the light fixture. • The maximum wattage rating for this fan’s light kit is 300 watts. For questions or to locate the nearest Casablanca Authorized Service Center, call 1-888-335-5247 toll-free, or visit us on the Web at www.casablancafanco.com. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residental installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. NOTE: Any changes or modifications to the transmitter or receiver not expressly approved by Casablanca Fan Company may void one’s authority to operate this remote control. 13 AUTHORIZED SERVICE CENTERS STATE/CITY ZIP SERVICE CENTER NAME PHONE TYPE ALABAMA MOBILE TUSCALOOSA HUNTSVILLE 36618 35405 35816 AZALEA CITY SERVICE CENTER LTG. & APPL./LIGHTING PLUS SOUTHERN HOME & HEARTH INC. 251-341-0663 205-345-8900 256-534-1715 ALASKA ANCHORAGE 99518 PRIMARY ELECTRIC INC. 907-563-7988 ARIZONA TUCSON PHOENIX GREEN VALLEY SEDONA PRESCOTT LAKE HAVASU CITY SCOTTSDALE GLENDALE PHOENIX YUMA MESA MESA TUCSON YOUNGTOWN TUCSON 85735 85019 85614 86336 86305 86403 85254 85308 85032 85364 85210 85204 85716 85363 85711 DESERT BREEZE FAN & ELEC. FAN-TASTIC ELECTRIC GOBLE ELECTRIC OAK CREEK AUDIO MARC PARENT/ELECTRICAL ETC. SOUND BANK ELECTRONICS VANDERVOORT ELECTRIC INC. BEA’S LAMPS & FANS THE BRASSWINDS SHOPPE CURLEY’S LITEHOUSE LOUD INC. DBA FANS PLUS GALLERY OF FANS ILLUMINATIONS ON BROADWAY LLC QUALITY HOME FAN DOCTOR SUN LIGHTING CO. 520-623-4646 602-866-1090 520-625-4938 928-282-5625 928-778-5935 928-855-1129 602-996-9637 602-978-0004 602-482-1881 520-782-4353 480-827-9302 480-962-0477 520-325-3031 602-274-6649 520-322-4303 ARKANSAS LITTLE ROCK CALIFORNIA SANTA ROSA GRASS VALLEY JAMESTOWN SANTA MARIA AUBURN SAN DIEGO FRESNO NEWHALL/SANTA CLARITA ATASCADERO CLOVIS SIMI VALLEY CORONA BAKERSFIELD SAN MARCOS STOCKTON MOORPARK SHINGLE SPRINGS CATHEDRAL CITY PLEASANTON RIVERSIDE TEMECULA SO. LAKE TAHOE CANYON LAKE VALENCIA SAN JOSE SACRAMENTO TULARE FRESNO SAN MARCOS SAN DIEGO RANCHO MIRAGE MURRIETA BAKERSFIELD SAN FRANCISCO TARZANA CHICO FRESNO MANTECA MISSION VIEJO REDDING CERRITOS MODESTO SAN RAFAEL SANTA CRUZ HUNTINGTON BEACH SAUGUS COLORADO LONGMONT DENVER ISO OWTS OWTS THE RANDY HALL CO. INC. 501-227-9915 95404 95945 95327 93455 95603 92115 93704 91321 ASEF’S APPLIANCE SERVICE ACCENT LIGHTING DASILVA’S LAMP & CEILING EVER-READY ELECTRIC THE FAN DOCTOR JOHN SHEPARD’S ELECT. SERV. LARRY MC COLLUM DAN MARTIN 707-575-3737 530-477-5483 209-984-4035 805-934-7091 530-823-8768 619-460-4132 559-438-5764 805-252-5769 93422 93612 93065 92881 93309 92069 95205 93021 95682 92234 94588 92505 92592 96150 92587 91354 95123 95819 93274 93710 92069 92111 92270 92562 93306 94109 91356 95928 93711 95336 92691 96002 90703 95350 94901 95062 92647 91350 MC NAMARA ELECTRIC INC. OMEGA SERVICE INC. PURCOM SYSTEMS JERRY F. PRYOR RB ELECTRIC & LTG. RD ELECTRICAL CONTR. RISSO ELECTRIC INC. R.J. SIEG ELECT. CO. JOHN ROZOWSKI CONST. R & R SERVICE S & L LIGHTING SERVICES VERNE SMITH TAB ELECTRIC TAHOE POOL SERVICE VILLAGE LIGHTS FANTASTIC FAN SERVICE SAL ZAMORA’S FAN REPAIR A & A LIGHT FIXTURES ANCHOR LIGHTING ENERGY HOUSE FAN DIEGO #1 FANDIEGO FANDIEGO INC. FANDIEGO #4 HILLCREST LTG-GALPIN INT HOUSE OF FANS INC. HYE LIGHTING CO. J&J LIGHTING INC. JAMES & CO LTG. MANTECA LIGHTING MOORE’S MISSION NORTH VALLEY LIGHTING COMFORTS OF HOME PHILLIPS ELECTRIC CO. RAFFLES RIVERSIDE LIGHTING THE TRADING POST VALLEY BREEZE FAN CO 805-466-1854 ISO/OWTS, 559-299-0495 ISO 805-583-8171 909-279-7775 ISO 805-831-2438 15-MILE RADIUS 760-727-1215 209-466-0781 800-799-0808 530-677-3850 760-324-2942 925-895-3762 951-687-9552 951-303-0850 530-541-4958 951-244-2910 ISO 800-800-3871 510-742-5560 916-452-7641 ISO 209-688-0696 OWTS 559-432-1500 ISO 760-743-3267 ISO 619-292-9244 ISO 760-779-9916 ISO 951-600-7867 ISO/OWTS 805-324-9966 415-885-1947 ISO 818-345-5544 ISO/OWTS 530-342-1815 ISO 209-486-7900 ISO/OWTS 209-823-1999 ISO 714-859-7090 HOME/ISO,/OWTS 530-221-6277 ISO/OWTS 562-865-6666 209-524-6287 OWTS 415-456-6660 ISO 831-423-7411 ISO 714-848-4353 OWTS 800-339-3267 80504 80229 L A ENTERPRISES M.D ELECTRIC 800-299-0222 303-288-7988 ISO TYPES OF SERVICE OFFERED: 14 OWTS = PRODUCT SOLD BY DEALER SERVICE CENTER NAME PHONE TYPE LOVELAND 80538 COLORADO SPRINGS 80903 FORT COLLINS 80525 LONGMONT 80501 CONNECTICUT NEW HARTFORD 06057 BRIDGEPORT 06605 CLINTON 06413 EAST HARTFORD 06118 WOODSTOCK 06281 WILLINGTON 06279 HARTFORD 06114 GREENWICH 06830 NEW HAVEN 06534 ZIP FIRESIDE LIGHTING INC. HOME LIGHTING INC. THE LIGHT CENTER LUMENAREA.COM INC. 970-669-3540 719-471-3520 970-226-3430 303-485-8600 OWTS OWTS OWTS OWTS B.W. MORSE & SONS.INC. FEDERAL ELECTRIC CONST.CO. GRAHAM CO. GRAHAM CO. RANDY MATTEAU GEORGE OPALENIK CONNECTICUT LTG. CTR. INC. FASHION LIGHT CENTER NEW GRAND LIGHT 860-379-9855 10 -MILE RADIUS 203-334-6455 800-942-5575 800-942-5575 860-963-8979 860-684-4558 860-249-7631 ISO 203-869-3098 ISO, OWTS 203-777-5781 ISO DELAWARE DOVER NEW CASTLE 19901 19720 BRUCE DRAJEM/ THE FAN MAN ERIC SHURR 302-734-7737 302-998-5147 FLORIDA WINTER HAVEN GAINSVILLE JACKSONVILLE SOUTH DAYTONA BOYNTON BEACH WINTER HAVEN NE PALM BAY NAPLES SPRINGHILL DAVIE NOKOMIS CORAL GABLES MAITLAND DEERFIELD BEACH TARPON SPRINGS CLEARWATER PUNTA GORDA ORLANDO TALLAHASSEE PORT CHARLOTTE BRANDON NAPLES 33880 32608 32217 32119 33437 33884 32905 34110 34606 33330 34275 33134 32751 33442 34689 33765 33982 32807 32303 33952 33511 34109 ALL ABOUT FANS & LIGHTING AUTHORIZED APPLIANCE SERV. AUTHORIZED APPLIANCE SERV. BOB’S FIX-IT CMS CYPRESS LIGHTING SHOWROOM FAN DOCTOR/ M. FERRUZZO GOODWIN ELECTRIC FAN DOCTOR/KEN R. CHURCHES LASERLAND INC. GRAHAM ELECTRICAL CONTR. MICHAEL HANSEN HENRY ELECTRIC CO. JARMO ELECTRIC INC. PETER LONTAKOS ELECTRICAL STEPHEN J. MERCER/ELECTRICAL SELECT SERVICE & REPAIR MID-FLORIDA FAN JIM LACZKO/TODAY’S KIDS JACKSONS LIGHTING INC. LUMENAIR LTG. & FANS WILSON LIGHTING OF NAPLES 863-299-9593 352-375-3886 904-737-5312 386-761-4055 561-736-0170 800-975-2677 321-728-5638 239-649-8880 352-683-4428 854-558-3743 941-486-8190 305-444-4111 407-834-4032 954-360-9024 727-938-8895\ 727-712-3090 941-637-7850 407-893-6226 850-562-4661 941-625-0044 813-653-3460 941-592-6006 GEORGIA COLUMBUS GRAYSON WOODSTOCK 31904 30017 30188 GRADY GLASS DBA DAN’S FAN CITY 706-571-3242 RG TENNEY ELECTRIC 770-378-9255 BRUCE A. RUGG, GC 404-925-1133 HAWAII KAILUA KONA HILO AIEA KAILUA KONA KAHULUI 96740 96720 96701 96740 96732 KU’S ELECTRONIC SVC. BAY LIGHTING & DESIGN THE FAN SHOP, INC. KONA COAST HOUSE OF LTS. INC. READ LIGHTING 808-329-4346 808-961-5688 808-488-1221 808-329-0748 808-871-8995 IDAHO MERIDIAN IDAHO FALLS 83642 83402 S-K ELECTRIC, INC. HOME LIGHTING 208-941-6264 208-523-2300 ILLINOIS CENTRALIA RICHMOND CHICAGO PRINCETON CHAMPAIGN BELLEVILLE SPRINGFIELD NORMAL SPRINGFIELD CORNLAND QUINCY TRENTON CHAMPAIGN YORKVILLE 62801 60071 60630 61356 61821 62223 62704 61761 62707 62519 62301 62293 61821 60560 BAKER APPLIANCE REPAIR CARAVELLE LIGHTING INC. D & S FAN SPECIALTIES INC. ELMORE ELECTRIC INC. TERRY GOBBLE JOHN HASSENSTAB HOME WORKS INC. KIRK SMALL APPLIANCE SHAWN SCHALK DELMAR VEECH HEINTZ LIGHTING CENTER LITE BRITE DIST SPRINGFIELD ELEC SPLY #3 UNIFIED SUPPLY INC. 618-532-8437 815-678-4558 847-824-2430 815-643-2354 217-384-5891 618-398-4640 217-753-3305 309-452-5248 217-585-0670 217-364-4121 217-223-0101 618-224-7314 217-351-7600 630-553-0660 INDIANA EVANSVILLE FORT WAYNE GREENFIELD VALPARAISO INDIANAPOLIS 47711 46805 46140 46383 46222 MICHAEL BAXTER CARL J. SMITH D & D REPAIR D & K ELECTRIC INDIANA LTG. CTR.INC. 812-453-6498 260-484-7295 317-467-0600 219-464-7576 317-293-9333 IOWA CEDAR RAPIDS SIOUX CITY SIOUX CENTER 52404 51106 51250 ACME ELECTRIC COMPANY DIVERSIFIED ELECTRONICS HILLS HOME SYSTEMS 319-365-8677 712-276-1034 712-722-2539 ISO 72212 ISO = IN-SHOP ONLY STATE/CITY ISO/OWTS = BOTH ISO ISO W PALM BEACH IN SHOP ONLY OWTS ISO OWTS/ISO ANY ISO OWTS ISO IN SHOP ONLY NO IN SHOP ISO ISO ISO ISO STATE/CITY ZIP SERVICE CENTER NAME PHONE MONTICELLO DES MOINES IOWA (CONTINUED) CARROLL CORALVILLE DAVENPORT 52310 50311 REM ELECTRIC INC. ADVANCED LIGHTING 319-465-3346 515-255-5009 TYPE 51401 52241 52803 J & L ELECTRIC INC. RALSTON CREEK SHAW ELECTRIC INC. 712-792-2444 319-351-2189 563-323-3611 ISO OWTSH/ISOA KANSAS WICHITA EMPORIA OVERLAND PARK OVERLAND PARK WICHITA MANHATTAN TOPEKA LENEXA SALINA OVERLAND PARK OVERLAND PARK 67211 66801 66213 66210 67226 66502 66611 66215 67401 66223 66212 ACTION APPLIANCE SERVICE INC. C.A.P. KAL ELECTRIC INC. RANDY RUSSELL ACCENT LTG INC. ENDACOTT LIGHTING K & S LIGHTING RENSEN HOUSE OF LIGHTS SALINA APPL. SHOWROOM WESTERN CHANDELIER CO. WILSON FANS & LIGHTING 316-263-0652 316-342-0448 913-897-6767 913-338-5330 316-636-1278 785-776-4472 785-267-0422 913-888-0888 785-827-1420 913-685-2000 913-642-1500 ISO KENTUCKY LEXINGTON 40510 CHARLET ELECT./RON CHARLET 606-231-7344 LOUISIANA LAFAYETTE HOUMA BATON ROUGE MONROE NEW IBERIA LAKE CHARLES METAIRIE 70501 70363 70815 71201 70560 70601 70006 ACADIA SERVICE CO. GULF SOUTH ARMATURE HOME APPLIANCE SERVICE ALBERT SURLCO WALET’S INC. JOSEPH’S ELECTRICAL CENTER INC. ROMAINE’S 318-233-8910 985-872-0486 504-272-7725 318-699-0619 318-364-7486 318-436-4930 504-887-7077 ISO ISO ISO MAINE SOUTH PORTLAND 04106 T.A. NAPOLITANO 207-799-0538 NO CLIPS MARYLAND FREDERICK WHITE HALL FORESTVILLE 21704 21161 20747 GL FAN SERVICE BT ELECTRIC/BILL TYRRELL BURGESS LIGHTING 301-831-4925 410-329-6353 301-568-8000 MASSACHUSETTS S. ATTLEBORO BRIDGEWATER MAYNARD W SPRINGFIELD NATICK DANVERS DENNIS WORCESTER NEW BEDFORD ORLEANS 02703 02324 01754 01089 01760 01923 02638 01603 02740 02653 AJ ELECTRIC BILTCLIFFE ELECTRIC HOUSE DOCTOR JALBERT ELECTRIC J.G. ELECTRIC CO INC. PLAZA LIGHTING RICK SEXTON EDWARD A. TORTORA VANDER ELECTRIC & EQUIPMENT CO. ASSOCIATED ELECTRICAL SERVICE 508-761-5021 508-697-7630 978-897-9085 413-734-4976 508-653-3042 978-774-7801 508-385-7536 508-755-3735 508-993-6383 508255-4589 MICHIGAN BELLEVILLE LANSING LANSING TRAVERSE CITY HOWELL BIRMINGHAM GRAND RAPIDS KALAMAZOO 48111 48906 48917 49686 48855 48009 49512 49002 MIKE AYERST INTEGRITY ELECTRIC LARGENT ENTERPRISES INC. CREATIVE LTG. & RESTORATION LIGHTNING ELECTRIC INC. CO 21ST CENTURY ELECTRIC GRAND RAPIDS LTG. CTR. INC. HODGSON ENTERPRISES 734-699-9698 517-484-0300 517-627-4229 231-938-1332 810-227-3375 248-645-6464 616-949-4931 269-343-4428 OWTS ISO ISO,OWTS 20 MI. RAD. ISO ISO ISO ISO ISO OWTS,ISO OWTS MINNESOTA ROCHESTER MINNEAPOLIS MAPLEWOOD MINNEAPOLIS PLYMOUTH BURNSVILLE EDEN PRAIRIE ST. PAUL BAXTER 55906 55422 55109 55411 55441 55337 55344 55108 56425 KROUPA’S ELECTRONICS LEO’S ELECTRIC SALES & SERVICE NORTH COUNTRY ELECTRIC PENN ELEC. MOTOR SERV. FAN MAN #101 (FLOWC #21) FAN MAN #102 (FLOWC #22) FAN MAN #106 (FLOWC#26) FAN MAN #107 (FLOWC #27) THE LIGHT DEPOT 507-281-4064 612-546-5625 651-748-4027 612-588-5333 612-559-0761 612-898-2754 612-941-9243 651-649-0686 218-829-0770 ISO ISO ISO ISO ISO MISSISSIPPI MADISON OCEAN SPRINGS 39110 39564 JACKSON SERVICE CTR. KELLY’S APPLIANCE 601-856-9469 228-872-7181 ISO MISSOURI SPRINGFIELD ST LOUIS SPRINGFIELD BRANSON 65802 63123 65804 65616 COMPLETE MAINTENANCE LEINWEBER SERVICE CO. LOYD’S ELECTRIC/ LIGHTHOUSE GALL. LOYD’S ELECTRIC SUPPLY INC. 417-866-2700 314-892-8177 417-889-1088 417-334-2171 MONTANA KALISPELL HELENA 59901 59601 LASALLE LIGHTING SUPREME LIGHTING 406-752-2424 406-442-8200 SECONDARY STATE/CITY ZIP SERVICE CENTER NAME PHONE MISSOULA 59801 WESTERN MONTANA LTG SPY 406-543-7166 NEBRASKA OMAHA GRAND ISLAND OMAHA NORFOLK LINCOLN 68104 68803 68144 68701 68510 D & L ELECTRONICS 402-571-5233 QUALITY SEW & VAC. 308-382-7310 OAK HILLS ELECTRIC INC. 402-691-4567 THE POWER STATION/FROHBERG ELEC. 402-371-6671 LINCOLN LIGHTING CTR. 402-476-1297 NEVADA SPARKS LAS VEGAS LAS VEGAS 89431 89103 89119 EAGLE ELECTRIC, INC. KS&S ELECTRIC, LLC FANCO 775-356-7300 702-222-9306 702-898-8522 NEW HAMPSHIRE NEW IPSWICH EXETER NASHUA 03071 03833 03060 HOUSE DOCTOR EDWARD HEINE AFFORDABLE FANS ETC. 603-731-5036 603-772-2359 603-759-8332 NEW JERSEY BELLMAWR WASHINGTON TRENTON THOROFARE MORRIS PLAINS LINWOOD RANDOLPH W. LONG BRANCH MULLICA HILL JACKSON CHESTER PARK RIDGE 08031 07882 08619 08086 07950 08221 07869 07764 08062 08527 07930 07656 JOSEPH ASHLEY C.P. ORLANDO WIRING UNLTD./RICHARD DOBRON HARRY R. HABICHT MANNY HERRERA JACK BRESLAU-HANDYMAN SVCS. ANTHONY MAKOMASKI CHRIS KIBBE/NO SHORTS ELECTRIC STEPHEN RICE ROBERT ROLZHAUSEN CHESTER LIGHTING, INC. KRELL LIGHTING 609-694-3785 908-689-4750 609-584-1122 856-845-2541 973-993-1137 609-601-1797 908-475-5569 732-222-4228 856-223-8645 732-363-3729 908-879-7200 201-391-7685 NEW MEXICO ALBUQUERQUE ROSWELL ALBUQUERQUE ALBUQUERQUE 87123 88201 87112 87109 FRANK’S ELECTRIC J & G ELECTRIC CO. A-1 LAMP DOCTOR B-ELECTRIC 505-293-6724 505-622-0146 505-296-5050 505-828-0241 NEW YORK COMMACK BROOKLYN ALBANY E. MEADOW BUFFALO QUEENSBURY HASTINGS BUFFALO PLAINVIEW NEWBURGH STATEN ISLAND YONKERS POUGHKEEPSIE ROCHESTER LONG BEACH SHOKAN LYNBROOK STATEN ISLAND REGO PARK AMHERST SCHENECTADY TROY COMMACK STATEN ISLAND PEARL RIVER BEDFORD CARLE PLACE BROOKLYN BROOKLYN NANUET AMHERST NEW YORK 11725 11204 12205 11554 14206 12804 13076 14226 11803 12550 10312 10704 12601 14620 11561 12481 11563 10301 11374 14228 12303 12180 11725 10304 10965 10507 11514 11219 11223 10954 14226 10003 AIR-TEK DBA REPUBLIC LIGHTING 631-499-1854 JERRY PICCOLINO/J&R SERVICE 718-259-1789 BERT ELECTRIC 518-869-7140 C.D. SERVICE 516-538-3481 CRAFTMASTERS SERVICENTER 716-893-9557 DEAN ELECTRIC 518-792-4781 ELECTRICAL WORK BY MARTY 315-668-0220 THE FAN COLLECTION, INC. 716-839-2447 JOSEPH GOTTDANK 516-932-7618 J D PARRELLA ELECT. 845-562-4112 JOE VALLETUTTI JR.. 718-608-9008 JAY D. KOSACK 914-237-9051 MANNINO ELECTRIC INC. 914-452-3520 BARRY MALADY DBA CAM ELECTRIC 585-271-8560 NICK’S IMPROVEMENT COMPANY 516-659-8989 OLIVE FANS & LTG. 845-657-5823 SHADERITE-PZ REPAIR 516-593-8973 FRANK RAGUCCI/F&R SERVICE CNTR. 718-273-5518 MARK RALIN 718-896-7844 SHANOR LTG. CTR. 716-691-3622 FRANK SALVATORE 518-355-5789 TROY LIGHT COMPANY 518-274-6931 TURNPIKE APPLIANCE 631-499-3355 V & P SERVICE CO/VITO PICCOLINO 718-447-7945 BOB VAZQUEZ 845-735-5861 BEDFORD LIGHTING INC. 914-666-0680 LIGHTING CTR. BY CAMEO INC. 516-747-4748 MAIN LAMP CORP. 718-436-2207 MANHATTAN LIGHTS INC. 718-998-1111 NOVA LIGHTING, INC. 914-623-5211 ROYALITE INC. 716-832-1492 SUPERIOR LIGHT & FAN 212-677-9191 NORTH CAROLINA SALISBURY CHARLOTTE HICKORY CHARLOTTE 28146 28205 28602 28203 HAUSS ELECTRICAL SERV. EFIRD’S INTERIORS, INC. EFIRD’S INTERIORS, INC. SIMPSONS LIGHTING /LT.FIXT 704-637-7774 704-376-5648 704-322-2203 704-376-5463 NORTH DAKOTA FARGO 58102 MIDSTATES ELECTRIC INC. 701-293-0441 OHIO CANTON COLUMBUS LOVELAND 44706 43235 45140 APPLIANCE PARTS CO. CERTIFIED SYSTEMS HANK GRINSHPAN 330-453-8077 614-799-0778 513-683-8666 TYPE ISO ISO 20 MI. RAD. ISO OWTS OWTS ISO SANTA FE ISO 20-MI. RAD. ISO IN SHOP QUEENS ISO ISO 20-MI. RAD. ISO ISO ISO ISO ISO ISO ISO OWTS ISO 15 STATE/CITY ZIP SERVICE CENTER NAME PHONE TYPE OHIO (CONTINUED) MAUMEE DAYTON COLUMBUS CLEVELAND N. OLMSTED NORTH LIMA SOUTH EUCLID DAYTON 43537 45419 43231 44109 44070 44452 44121 45459 K.O.V ELECTRONIC REPAIR LARKIN ELECTRIC CO. THE LAMP LIGHTER WESTSIDE LTG. CTR. CHANDELIER SHACK INC. DICKEY ELECTRIC LAMPSHADER EAST/DBA LTG. EXPO OHIO LAMP & FIXTURE CO. 419-865-8893 937-294-4115 614-891-7940 216-459-1970 440-777-6969 330-549-3976 216-291-3030 937-439-0822 OKLAHOMA OKLAHOMA CITY OKLAHOMA CITY OKLAHOMA CITY 73105 73132 73127 APPLIANCE SERVICE BY CK LARKIN E. STEVENSON JAMES LIGHTING INC. 405-525-8862 405-728-8810 405-947-6663 OREGON PORTLAND BEND 97225 97701 SYLVAN ELECTRONICS INC. DESIGN LIGHTING INC. 800-473-1244 541-389-9997 PENNSYLVANIA HOPWOOD DREXEL HILL ALLENTOWN PITTSBURGH PHILADELPHIA EASTON ALLENTOWN LANCASTER WEST CHESTER FAIRLESS HILLS WEST READING HARRISBURG CONSHOHOCKEN WILLOW GROVE STATE COLLEGE 15445 19026 18105 15224 19111 18045 18102 17601 19382 19030 19611 17111 19428 19090 16803 GEORGE R. SMALLEY CO. INC. PATRICK HASTINGS LIGHTING FIXTURE & SUPPLY CO MARK DIULUS ELECTRIC CO. KLAUS OTTE PRIMROSE ELECTRICAL SCHOLL’S ELECTRIC S. DEAN’S ELECTRIC TOBIAS ELECTRIC ASTRO LTG. GALLERIES A TO Z VACUUM STORES YALE ELECTRIC SUPPLY KAY ELECTRIC SUPPLY NORTH-WEST ELEC. SUPPLY CO. WHITEHILL LIGHTING & SPLY. 724-437-1927 610-853-2709 610-435-9691 412-681-2553 215-745-4266 610-258-1359 610-435-5876 717-2854545 610-942-4000 215-943-0331 610-374-4888 717-233-8401 610-825-0100 215-659-5757 814-238-2449 RHODE ISLAND PAWTUCKET 02861 WICKFORD APPLIANCE & LTG CTR. 401-726-4240 ISO SOUTH CAROLINA HANAHAN SPARTANBURG BLUFFTON GOOSE CREEK MYRTLE BEACH COLUMBIA 29406 29306 29910 29445 29575 29212 BOBBY LUTES ELECTRICAL INC. BOBBY JACKSON ELECTR. J. HEAVENER & CO. DAVID MIMS RAY ELECTRIC EASTWIND ENTERPRISES 843-797-0948 803-583-6035 843-837-8300 843-514-2380 843-293-0068 803-781-3267 ISO SOUTH DAKOTA SIOUX FALLS SIOUX FALLS 57105 57104 LAMPS AND SHADES INC. MAHLANDER’S 605-332-6680 605-336-7798 TENNESSEE MT CARMEL MEMPHIS LOUISVILLE BRENTWOOD 37645 38111 37777 37027 APPALACHIAN ELEC. SVC. APPLIANCE SERVICE CTR. BEN SNYDER PAUL TAMPIEN/SUNSHINE ELECT. 423-357-0783 901-324-5898 865-380-5491 615-371-9383 TEXAS LEWISVILLE HOUSTON CORPUS CHRISTI FREEPORT AMARILLO DENTON ODESSA DENTON DAMON 75067 77089 78404 77541 79106 76201 79761 76201 77430 SOUTHERN COMFORTS BENNETT FAN INSTALL., INC. BRAND APPLIANCE & MICROWAVE SKIP’S ELECTRIC AND AIR DI’S LAMP & FAN REPAIR FANTASIA CEILING FANS GOFORTH ELECTRIC LARRY W. GOFF GULF COAST FAN SERVICE 940-536-1406 281-484-1401 512-854-1851 979-233-3903 806-331-5267 940-484-4222 432-550-8927 940-387-7304 281-495-6434 ISO OWTS/ISO ISO ISO ISO IN HOME ONLY ISO OWTS ISO ISO ISO ISO STATE/CITY ZIP SERVICE CENTER NAME PHONE KERRVILLE PARIS SAN ANTONIO AUSTIN GIDDINGS LUBBOCK ARLINGTON TYLER HEARE CARROLLTON HUMBLE AUSTIN HOUSTON RICHARDSON HURST BEAUMONT DALLAS VICTORIA SAN ANGELO WICHITA FALLS HOUSTON HARLINGEN MCALLEN SEALY 78029 75460 78212 78757 78942 79413 76001 75707 77859 75006 77338 78703 77069 75080 76053 77702 75206 77904 76904 76308 77063 78550 78504 77474 MAURICE HAMMIT HARGIS ELECTRIC CEILING FAN SERVICE CTR. KLOCK ELECTRIC ORSAG’S INC. ORECK VACUUMS P&M QUALITY CONT. CHARLES R. RAINS THOMPSON SUPPLY ADFANTAGE CEILING FAN CAROLS LTG. & FAN SHOP TEXAS CEILING FANS/CEILING FAN SHOP CHAMPIONS LIGHTING COOL BREEZES ARC FAN & LIGHTING FAN FACTORY LIGHTS FANTASTIC HALL ELECTRIC CO., INC. HERITAGE HAUS LANTERN HOUSE INC. LIGHTING PLUS INC. THE LIGHT HOUSE THE LIGHT HOUSE TEXAS CEILING FANS 210-367-4937 903-785-8055 210-804-1362 512-837-4704 409-542-3167 806-792-2821 817-478-2004 903-566-3119 409-280-5737 972-446-9393 281-446-7613 512-477-3132 281-440-5339 972-690-4580 817-268-2218 409-833-8207 214-987-9655 512-578-6221 325-949-6541 940-692-7381 713-784-2440 956-423-6664 956-631-1155 979-885-6900 TYPE UTAH MURRAY RIVERTON LAYTON 84107 84065 84040 CENTRAL ELECTRIC CO. VERN O. FRANCIS HARUO YOSHIKAWA 801-467-5479 801-254-4178 801-546-6008 VIRGINIA RICHMOND BURKE WILLIAMSBURG VIRGINIA BEACH 23228 22015 23185 23451 FANNING ELECTRICAL SERVICE L&S ELECTRIC INC. TAPROOT COMPANY FANS,LIGHTING, ‘N’ MORE 804-262-3681 703-237-0011 757-229-3722 757-422-3616 WASHINGTON SPOKANE TACOMA WENATCHEE PASCO BELLINGHAM YACOLT YAKIMA 99216 98404 98801 99301 98225 98675 98902 BRITE-WAY ELECTRIC 509-922-0275 M.G.M. ELECTRONICS 253-752-9826 SEW CREATIVE/ADVANTAGE STORE 509-663-5516 ARHA TOTAL SERVICE 509-547-3799 JOHN WIGGINS DBA TWIN SISTER’S ELEC. 360-676-1257 S&L ELECTIRC 503-657-0633 INLAND LIGHTING 509-248-4647 ISO WASHINGTON, DC WASHINGTON 20007 FAN FAIR 202-342-6290 ISO WEST VIRGINIA SO. CHARLESTON WHEELING 25309 26003 PEPPER ELECTRIC TOP HAT STOVE SALES 304-768-8195 304-233-6262 WISCONSIN MILWAUKEE GREEN BAY FONTANA BROOKFIELD MADISON LA CROSSE 53219 54313 53125 53005 53719 54601 BOB’S FAN REPAIR KARL DEVROY J&L PROPERTY MAINT. CITY LIGHTS & FANS MADISON LIGHTING WETTSTEIN’S 414-546-2501 920-494-6090 262-275-2345 414-781-9048 608-271-6911 608-784-5555 CANADA TORONTO, ONT., M6M2P5 ZANEEN LIGHTING 416-247-922 OVERSEAS ST. THOMAS 00805 DUANE LOBERG 809-775-2399 ISO ISO ISO ISO,OWTS ISO ISO ISO OWTS OWTS ISO ISO ISO/OWTS ISO PRODUCT SPECIFICATIONS Collection: Model name: Model number: Dimensions: NOTE: Dimension B includes light fixture and glass. Weight: 16 Casablanca Signature Seacoast C3U72M A = 16" B = 17" 17 C = 33" D = 11.8" E = 5.6 5.6" 50 lbs. Finishes: Motor: Blade span: Blade iron pitch: No. of blades: Technology: Lightbulb type: No. of lightbulbs: Archetectural White 188 x 20 mm - C1LT type 54 inches 15 degrees 5 Versa•Touch2™ 45-watt tube light with 44,000-hour bulb life 3