Download Sharp XL-HP500H Service manual
Transcript
XL-HP500 SERVICE MANUAL No. SY298XLHP500/ MICRO COMPONENT SYSTEM MODEL XL-HP500 XL-HP500 Micro Component System consisting of XL-HP500 (main unit) and CP-HP500 (speaker system). • In the interests of user-safety the set should be restored to its original condition and only parts identical to those specified be used. CONTENTS Page IMPORTANT SERVICE NOTES (FOR U.S.A. ONLY) ....................................................................................................... 2 SPECIFICATIONS ............................................................................................................................................................. 2 NAMES OF PARTS ........................................................................................................................................................... 3 DISASSEMBLY .................................................................................................................................................................. 5 REMOVING AND REINSTALLING THE MAIN PARTS ..................................................................................................... 7 ADJUSTMENT ................................................................................................................................................................... 9 NOTES ON SCHEMATIC DIAGRAM .............................................................................................................................. 12 TYPES OF TRANSISTOR AND LED ............................................................................................................................... 12 BLOCK DIAGRAM ........................................................................................................................................................... 13 SCHEMATIC DIAGRAM / WIRING SIDE OF P.W.BOARD ............................................................................................. 16 VOLTAGE ........................................................................................................................................................................ 33 WAVEFORMS OF CD CIRCUIT ...................................................................................................................................... 34 TROUBLESHOOTING ..................................................................................................................................................... 35 FUNCTION TABLE OF IC ................................................................................................................................................ 39 FL DISPLAY ..................................................................................................................................................................... 46 REPLACEMENT PARTS LIST/EXPLODED VIEW PACKING OF THE SET (FOR U.S.A. ONLY) SHARP CORPORATION This document has been published to be used for after sales service only. The contents are subject to change without notice. XL-HP500 FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER TO THE OPERATION MANUAL. IMPORTANT SERVICE NOTES (FOR U.S.A. ONLY) BEFORE RETURNING THE AUDIO PRODUCT (Fire & Shock Hazard) Before returning the audio product to the user, perform the following safety checks. 1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the audio product. 2. Inspect all protective devices such as insulating materials, cabinet, terminal board, adjustment and compartment covers or shields, mechanical insulators etc. 3. To be sure that no shock hazard exists, check for leakage current in the following manner. * Plug the AC line cord directly into a 120 volt AC outlet. * Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal cabinet parts and a known earth ground, such as conduit or electrical ground connected to earth ground. * Use a VTVM or VOM with 1000 ohm per volt, or higher, sensitivity to measure the AC voltage drop across the resistor (See diagram). * Connect the resistor connection to all exposed metal parts having a return path to the chassis (antenna, metal cabinet, screw heads, knobs and control shafts, escutcheon, etc.) and measure the AC voltage drop across the resistor. VTVM AC SCALE 1.5k ohms 10W 0.15 µ F TO EXPOSED METAL PARTS TEST PROBE CONNECT TO KNOWN EARTH GROUND All check must be repeated with the AC line cord plug connection reversed. Any reading of 0.3 volt RMS (this corresponds to 0.2 milliamp. AC.) or more is excessive and indicates a potential shock hazard which must be corrected before returning the audio product to the owner. SPECIFICATIONS ■ General Power source Power consumption Dimensions Weight ■ CD player AC 120 V, 60 Hz 102 W Signal readout Width: 8-1/8" (205 mm) Height: 10-1/4" (260 mm) Depth: 14-7/16" (366 mm) 13.2 lbs. (6.0 kg) ■ Amplifier (Except for Canada) Output power Output terminals Input terminals 50 watts minimum RMS per channel into 6 ohms from 60 Hz to 20 kHz, 10% total harmonic distortion Speakers: 6 ohms Headphones: 16 - 50 ohms (recommended: 32 ohms) Subwoofer pre-out (audio signal): 200 mV/ 10 k ohms at 70 Hz Video/Auxiliary (audio signal): 500 mV/47 k ohms ■ Amplifier (For Canada) Output power Output terminals Input terminals Type RMS: 100 W (50 W + 50 W) (10 % T.H.D.) Speakers: 6 ohms Headphones: 16 - 50 ohms (recommended: 32 ohms) Subwoofer pre-output (audio signal): 200 mV/10 k ohms at 70 Hz Video/Auxiliary (audio signal): 500 mV/47 k ohms Specifications for this model are subject to change without prior notice. D/A converter Frequency response Dynamic range 3-disc multi-play compact disc changer player Non-contact, 3-beam semiconductor laser pickup 1-bit D/A converter 20 - 20,000 Hz 90 dB (1 kHz) ■ Tuner Frequency range FM: 87.5 - 108 MHz AM: 530 - 1,720 kHz ■ Cassette deck Frequency response Signal/noise ratio Wow and flutter 50 - 14,000 Hz (normal tape) 50 dB (recording/playback) 0.3 % (WRMS) ■ Speaker Type Maximum input power Rated input power Impedance Dimensions Weight –2– 2-way type speaker system 2" (5 cm) Tweeter 5-1/8" (13 cm) Woofer 100 W 50 W 6 ohms Width: 6-1/2" (165 mm) Height: 10-1/4" (260 mm) Depth: 9-1/2" (241 mm) 5.5 lbs. (2.5 kg)/each XL-HP500 NAMES OF PARTS ■ Front panel 1. Disc Trays 2. Power On/Stand-by Button 3. Timer/Sleep Button 4. Clock Button 5. Tuning and Time Down Button 6. Tuning and Time Up Button 7. Timer Set Indicator 8. Headphone Jack 9. CD Eject Buttons 10. CD Direct Play Buttons 11. Equalizer Mode Select Button 12. Extra Bass/Demo Mode Button 13. Volume Control 14. Cassette Compartment 15. Tape Reverse Play Button 16. CD or Tape Stop Button 17. CD Play or Repeat, Tape Forward Play Button 18. CD Track Down or Fast Reverse, Tape Fast Wind, Tuner Preset Down Button 19. CD Track Up or Fast Forward, Tape Fast Wind, Tuner Preset Up Button 20. CD Button 21. Tape Record Pause Button 22. Video/Auxiliary Button 23. Tape Reverse Mode Select Button 24. Memory/Set Button 25. Tuner (Band) Button 26. Tape Button 1 9 2 10 3 4 5 6 7 11 12 13 14 15 8 16 17 18 19 20 22 21 23 24 25 26 ■ Display 1 2 3 4 5 1. Disc Number Indicators 2. CD Play Indicator 3. Tape Reverse Mode Indicator 4. Tape Reverse Play Indicator 5. Tape Forward Play Indicator 6. FM Stereo Mode Indicator 7. FM Stereo Receiving Indicator 8. Memory Indicator 9. Extra Bass Indicator 10. Timer Recording Indicator 11. Timer Play Indicator 12. CD Pause Indicator 13. CD Repeat Play Indicator 14. Tape Record Indicator 15. Sleep Indicator 6 7 8 9 10 11 12 13 14 15 4 ■ Rear panel 5 1. Cooling Fan 2. Subwoofer Pre-output Jack 3. AC Power Cord 4. FM/AM Loop Antenna Jack 5. Video/Auxiliary (Audio Signal) Input Jacks 6. Speaker Terminals 1 2 6 Note: This product is equipped with a cooling fan inside, which begins to run at a specified volume level for better heat radiation. 3 1 2 3 ■ Speaker system 4 1. Tweeter 2. Woofer 3. Bass Reflex Duct 4. Speaker Terminals –3– XL-HP500 ■ Remote control 1. Remote Control Transmitter 2. CD Direct Play Buttons 3. CD Track Down or Fast Reverse, Tape Fast Wind, Tuner Preset Down Button 4. Clock Button 5. Equalizer Mode Select Button 6. Extra Bass Button 7. Power On/Stand-by Button 8. CD Button 9. Tuner (Band) Button 10. Tape Button 11. Video/Auxiliary Button 12. CD Track Up or Fast Forward, Tape Fast Wind, Tuner Preset Up Button 13. Volume Up and Down Buttons 14. Disc Direct Search Buttons 15. Clear Button 16. CD Memory Button 17. CD Stop Button 18. CD Pause Button 19. Tape Reverse Mode Select Button 20. Tape Reverse Play Button 21. Tape Stop Button 22. CD Play or Repeat Button 23. Tape Record Pause Button 24. CD Random Button 25. Tape Forward Play Button 1 7 2 8 17 18 19 20 21 22 23 24 25 9 10 3 12 13 14 4 5 6 11 15 16 Buttons with " " mark in the illustration can be operated on the remote control only. –4– XL-HP500 DISASSEMBLY Top Cabinet Caution on Disassembly Follow the below-mentioned notes when disassembling the unit and reassembling it, to keep it safe and ensure excellent performance: 1. Take cassette tape and compact disc out of the unit. 2. Be sure to remove the power supply plug from the wall outlet before starting to disassemble the unit. 3. Take off nylon bands or wire holders where they need to be removed when disassembling the unit. After servicing the unit, be sure to rearrange the leads where they were before disassembling. 4. Take sufficient care on static electricity of integrated circuits and other circuits when servicing. STEP REMOVAL PROCEDURE FIGURE 1 Top Cabinet 1. Screw ...................... (A1) x5 5-1 2 Side Panel (Left/Right) 1. Screw .................... (B1) x10 5-1 3 Rear Panel 1. Screw ...................... (C1) x7 2. Screw ...................... (C2) x2 3. Flat Cable ............... (C3) x1 5-2 4 CD Changer Mechanism Unit 1. Hook ........................ (D1) x2 2. Socket ..................... (D2) x1 3. Flat Cable ............... (D3) x2 5-2 Front Panel 1. Screw ...................... 2. Hook ........................ 3. Socket ..................... 4. Flat Cable ............... 5. Flat Wire .................. 5 6 Main PWB (B1) x1 ø3x10mm (A1) x2 ø3x12mm Front Panel Side Panel (Right) (A1) x1 ø3x10mm (A1) x2 ø3x12mm (B1) x2 ø3x10mm (B1) x2 ø3x10mm (B1) x3 ø3x10mm Rear Panel Side Panel (Left) (B1) x2 ø3x10mm Figure 5-1 CD Changer Mechanism Unit (D3) x2 (E1) x3 5-2,5-3 (E2) x2 5-3 (E3) x2 (E4) x1 (E5) x1 Front Panel Hook (D1)x1 CD Servo PWB 1. Screw ....................... (F1) x2 5-2,6-1 2. Socket ...................... (F2) x2 6-1 7 Power PWB 1. Screw ...................... (G1) x4 6-1 8 Display PWB 1. Knob ........................ (H1) x1 2. Screw ...................... (H2) x9 3. Flat Cable ............... (H3) x1 6-2 9 Tape Mechanism 1. Screw ....................... (J1) x4 6-2 10 Headphones PWB 1. Screw ...................... (K1) x1 6-2 11 CD Servo PWB (Note 1) 1. Screw ....................... (L1) x3 2. Socket ...................... (L2) x6 6-3 12 CD Changer Mechanism Unit 1. Screw ...................... (M1) x4 2. Screw ...................... (M2) x2 3. Top Board ............... (M3) x1 4. Stabilizer Holder ..... (M4) x1 5. Disk Tray ................. (M5) x3 6. Screw ...................... (M6) x3 7. Guide,Mecha Holder .. (M7) x1 8. Screw ...................... (M8) x1 9. Stopper ................... (M9) x1 10. Holder,Mecha ..... (M10) x1 11. Screw .................. (M11) x4 6-3 6-4 (D2) x1 Rear Panel Display PWB Pull (C3) x1 Pull Main PWB Hook (D1)x1 (E1) x1 ø3x10mm Jack PWB (C1) x7 ø3x10mm (F1) x1 ø3x10mm (C2) x2 ø3x10mm Figure 5-2 (E3) x1 (E4) x1 Tape Mechanism (E5) x1 Front Panel Note 1: After removing the connector for the optical pickup from the connector, wrap the conductive aluminium foil around the front end of the connector so as to protect the optical pickup from electrostatic damage. Main PWB Display PWB Hook (E2)x1 Pull (E3) x1 Hook (E2)x1 Pull (E1) x2 ø3x10mm Power PWB Figure 5-3 –5– XL-HP500 (F1) x1 ø3x10mm Stabilizer Holder (M4) x1 (F2) x1 Push (M2) x2 ø2 x7mm (F2) x1 (M6) x1 ø2.6 x12mm Main PWB Pawl (M7) x1 (M10) x1 (G1) x4 ø4x8mm (M9) x1 Spring CD Mechanism Top Board (M3) x1 (M11) x4 ø2.6 x10mm (M6) x2 ø2 x6mm (M8) x1 ø3 x3mm Power PWB Disc Tray 1 Figure 6-1 Turn clockwise the main cam to raise the CD mechanism up to the uppermost position. (H3) x1 Front Panel 1 2 3 Disc Tray 2 (M5) x3 (H1) x1 Disc Tray 3 Press in turns the arrow parts, starting with the uppermost one, to withdraw the disc trays. Figure 6-4 (H2) x9 ø2.6x10mm Tape Mechanism Display PWB (K1) x1 ø3x10mm Open Cassette Holder Headphones PWB STEP (J1) x4 ø3x10mm FIGURE Woofer 1. Net Frame ............... 2. Catching Holder ...... 3. Screw ...................... 4. Screw ...................... (A1) x1 (A2) x4 (A3) x4 (A4) x4 6-5 2 Tweeter 1. Screw ...................... (B1) x2 6-5 Figure 6-2 CD Changer Mechanism Unit PROCEDURE REMOVAL 1 (M1) x2 ø3x10mm Tweeter (B1) x2 ø3x10mm (A4) x4 ø4x12mm (A2) x2 (A3) x2 Net Frame ø3x12mm (A1) x1 (L2) x6 Woofer (M1) x2 ø3x10mm (A3) x2 ø3x12mm (L1) x3 ø3x10mm CD Servo PWB (A2) x2 Figure 6-3 Figure 6-5 –6– XL-HP500 REMOVING AND REINSTALLING THE MAIN PARTS TAPE MECHANISM SECTION Clutch Ass'y Perform steps 1 to 9 of the disassembly method to remove the tape mechanism. Record/Playback Head How to remove the Record/Playback Head (See Fig. 7-1) 1. When you remove the screws (A1) x 2 pcs and (A2) x 1 pc., the record/playback head can be removed. Erase Head How to remove the Pinch Roller (See Fig. 7-2) (A1)x2 Ø2x6mm 1. Carefully bend the pinch roller pawl in the direction of the arrow <A>, and remove the pinch roller (B1) x 1 pc., in the direction of the arrow <B>. Note: When installing the pinch roller, pay attention to the spring mounting position. (A2)x1 Ø2x9mm Figure 7-1 How to remove the Belt (See Fig. 7-3) 1. Remove the main belt (C1) x 1 pc., from the motor side. 2. Remove the FF/REW belt (C2) x 1 pc. How to remove the Motor (See Fig. 7-4) Pinch Roller (B1)x1 Pull 1. Remove the screws (D1) x 2 pcs., to remove the motor. Pinch Roller <A> Pawl <B> Figure 7-2 FF/REW Clutch Motor FF/REW Belt (C2)x1 Main Belt (C1)x1 Flywheel Figure 7-3 Motor Clutch Ass'y (D1)x2 Ø2.6x5mm Figure 7-4 –7– XL-HP500 CD MECHANISM SECTION Perform steps 1 to 4 and 11 to 12 of the disassembly method to remove the CD mechanism. (A1) x2 ø2.6 x5mm Stop Washer (A3) x1 Optical Pickup How to remove the Optical Pickup (See Fig. 8-1) CD Mechanism 1. Remove the screws (A1) x 2 pcs and shaft (A2) x 1 pc. 2. Remove the stop washer (A3) x 1 pc and gear (A4) x 1 pc. 3. Remove the optical pickup. Note: After pulling out the optical pickup connector, wrap the tip of it with conductive aluminium foil or the like to protect the optical pickup from the static electricity. Shaft (A2) x1 Gear (A4) x1 Figure 8-1 (B2) x2 ø2.6 x4mm How to remove the Tray Motor and the Main Cam Motor (See Fig. 8-2) (B2) x2 ø2.6 x4mm 1. Remove the CD changer mechanism unit by the method described in page 7, and disassemble as shown in the figure. 2. Remove the belt (B1) x 2 pcs from the motor side. 3. Remove the screws (B2) x 4 pcs. 4. Remove the tray motor and the main cam motor. Belt (B1) x1 Belt (B1) x1 Main Cam Motor Tray Motor Figure 8-2 How to remove the CD Disc (When CD is in the playback state) (See Fig. 8-3) Turn the main cam clockwise and raise the CD mechanism and disk holder up to the uppermost position. 1. Remove the cabinet and front panel. 2. Disassemble as shown in the figure so that the CD disc of CD changer becomes visible. 3. Remove the CD disc as shown in the figure. Disk Holder CD Disk CD Changer Mechanism Unit (When CD is in playback state) Figure 8-3 How to remove the CD Disc (When CD exists in the tray) (See Fig. 8-4) Turn the main cam clockwise and raise the CD mechanism and disk holder up to the uppermost position. 1. Remove the cabinet and front panel. 2. Disassemble as shown in the figure so that the CD disc of CD changer can be taken out. 3. Remove the CD disc from the tray as shown in the figure. Disc Holder CD Mechanism CD Changer Mechanism unit CD Disk 1 2 3 Press in turns the arrow parts, starting with the uppermost one, to withdraw the disc trays Disk Tray 1 Disk Tray 2 Disk Tray 3 (When CD exists in the tray) Figure 8-4 –8– XL-HP500 ADJUSTMENT • Tape Speed MECHANISM SECTION • Driving Force Check Torque Meter Test Tape Adjusting Point Specified Value Instrument Connection MTT-111 Variable Resistor in motor. 3,000 ± 30 Hz Speaker Terminal (Load resistance: 6 ohms) Specified Value Play: TW-2111 Normal speed Over 80 g • Torque Check Torque Meter Specified Value Play: TW-2111 30 to 80 g.cm Fast forward: TW-2231 70 to 180 g.cm Rewind: TW-2231 70 to 180 g.cm TAPE MECHANISM TUNER SECTION Tape Motor fL: Low-range frequency fH: High-range frequency • AM IF/RF Signal generator: 400 Hz, 30%, AM modulated Test Stage Frequency Variable Resistor in motor Figure 9-1 Frequency Display Setting/ Instrument Adjusting Connection Parts AM IF 450 kHz 1,602 kHz T351 AM Band Coverage — 531 kHz (fL): T306 *2 1.1 ± 0.1 V 990 kHz (fL): T303 AM Tracking 990 kHz CD SECTION • Adjustment Since this CD system incorporates the following automatic adjustment functions, readjustment is not needed when replacing the pickup. Therefore, different PWBs and pickups can be combined freely. Each time a disc is changed, these adjustments are performed automatically. Therefore, playback of each disc can be performed under optimum conditions. *1 *1 *1. Input: Antenna Output: TP302 *2. Input: Antenna Output: TP301 • FM RF Signal generator: 1 kHz, 40 kHz dev., FM modulated Setting/ Adjusting Point Test Stage Frequency Frequency Display FM Band Coverage — 87.50 MHz FM RF 98.00 MHz 98.00 MHz (10-30 dB) Items adjusted automatically (1) Offset adjustment (The offset voltage between the head amplifier output and the VREF reference voltage is compensated inside the IC.) * Focus offset adjustment * Tracking offset adjustment (2) Tracking balance adjustment (3) Gain adjustment (The gain is compensated inside the IC so that the loop gain at the gain crossover frequency will be 0 dB.) * Focus gain adjustment * Tracking gain adjustment Instrument Connection T301 (fL): 1.3 V ± 0.1 V *1 L312 *2 *1. Input: Antenna Output: TP301 *2. Input: Antenna Output: Speaker terminal • FM IF Signal generator: 10.7 MHz, FM modulated Setting/ Adjusting Point Test Stage Frequency Frequency Display 10.7 MHz *1. Input: Antenna 98 MHz Error T302 *1 (Turn the core of transformer T302 fully counterclock wise) Output: TP301 IC302 T351 T301 FM OSC T302 FM IF IC303 CNP302 AM IF L312 FM RF FM/AM LOOP ANTENNA 01 10* CAM error. Can't detect CAM switch when CAM is moving. 11* When it detect CAM operation error during initialize process. 20* TRAY error. Can't detect TRAY switch when TRAY is moving. 21* When it detect TRAY operation error during initialize process. 22* When it detect invalid TRAY switch during normal operation. 23* When it detect invalid TRAY switch during initialize procecss. 31 When it change to CD function, DSP cannot read initial data. * 'CHECKING' If Error is detected, 'CHECKING' will be displayed instead of 'ER-CD**'. 'ER-CD**' display will only be displayed when error had been detected for the 5th times. TP301 R357 TP302 AM BAND COVERAGE fL Explanation When Pickup set inner position, inner switch cannot detect 'ON' level for 10 secs. MAIN PWB-A1 IC301 IF CD ERROR CODE DESCRIPTION Instrument Connection T303 AM TRACKING fL T306 Figure 9-2 ADJUSTMENT POINTS –9– XL-HP500 TEST MODE • Setting the test mode Any one of test mode can be set by pressing several keys as follows. <X-BASS> + <CD> + <ON/STAND-BY> TEST: CD operation test. Function: -CD test mode. -Enter test 4 mode. C D T E S T IL isn't done OPEN/CLOSE operation is using manual. << >>, << >> buttons make pick's slide possible. <<PLAY>> key input. Do TOC IL. Do normal play. When these following key is input into PLAY key, track number can be appoint directly. <<MEMORY>> key input. Adjustment result automatically will display as below. for each 2 sec : a) "FOFF_XX" b) "TOFF_XX" c) "TBAL_XX" d) "TGAN_XX" f) "FGAN_XX" g) "RFLS_XX" explanation: a) Focus off set b) Tracking off set c) Tracking balance d) Tracking Gain f) Focus Gain g) RF level shift = "FOFF_XX" = "TOFF_XX" = "TBAL_XX" = "TGAN_XX" = "FGAN_XX" = "RFLS_XX" <<MEMORY>> key input. Laser ON. <<MEMORY>> key input. Tracking OFF play at that specific point. <<MEMORY>> key input. << << << 1>> key: Track 4 2>> key: Track 9 3>> key: Track 15 Tracking ON play from that specific point. <<MEMORY>> key input. <<STOP>> key input. STOP VOL — Last memory BAL — CENTER P.GEQ — FLAT X-BASS — OFF Adjustment result automatically will display as below for each 2 sec : a) "FOFF_XX" b) "TOFF_XX" c) "TBAL_XX" d) "TGAN_XX" f) "FGAN_XX" g) "RFLS_XX" <<STOP>> key input. STOP Sliding the PICKUP with >>, << >> button << must only be in STOP mode. To cancel : Power OFF – 10 – XL-HP500 Standard Specification of Stereo System Error Message Display Contents Error Contents CD DISPLAY Notes Pickup Mechanism Error. 'ER-CD01' PU-IN SW Detection NG. CD Changer Mechanism Error. 'ER-CD**' (*) 10: CAM SW Detection NG during normal operation. 11: CAM SW Detection NG during initialize process. 20: TRAY SW Detection NG during normal operation. 21: TRAY SW Detection NG during initialize process. 22: Invalid TRAY SW value during normal operation. 23: Invalid TRAY SW value during initialize process. CD DSP Communication Error 'ER-CD31' Focus Not Match/ 'NO DISC' DSP COMMUNICATION ERROR IL Time Over. TUNER PLL Unlock. FM 87.50 MHz PLL Unlock. (*) CHECKING: If error is detected, 'CHECKING' will be displayed instead of 'ER-CD**' . 'ER-CD**' display will only be displayed when error had been detected for the 5th times. Speaker abnormal detection and +B PROTECTION display In case speaker abnormal detection or +B PROTECTION had occurred, it can be check by pressing 'POWER', 'VIDEO' and 'XBASS' key twice. Display will show "S** B**". S is referring to speaker abnormal detection and B is referring to +B PROTECTION. ** is in hex valve. +B PROTECTION is condition when irregular process occur on power supply line. – 11 – XL-HP500 NOTES ON SCHEMATIC DIAGRAM • Resistor: To differentiate the units of resistors, such symbol as K and M are used: the symbol K means 1000 ohm and the symbol M means 1000 kohm and the resistor without any symbol is ohm-type resistor. Besides, the one with “Fusible” is a fuse type. • Capacitor: To indicate the unit of capacitor, a symbol P is used: this symbol P means pico-farad and the unit of the capacitor without such a symbol is microfarad. As to electrolytic capacitor, the expression “capacitance/withstand voltage” is used. (CH), (TH), (RH), (UJ): Temperature compensation (ML): Mylar type (P.P.): Polypropylene type • Schematic diagram and Wiring Side of P.W.Board for this model are subject to change for improvement without prior notice. REF. NO DESCRIPTION • The indicated voltage in each section is the one measured by Digital Multimeter between such a section and the chassis with no signal given. 1. In the tuner section, indicates AM indicates FM stereo 2. In the main section, a tape is being played back. 3. In the deck section, a tape is being played back. 4. In the power section, a tape is being played back. 5. In the CD section, the CD is stopped. • Parts marked with “ 1 ” ( ) are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. POSITION REF. NO ON—OFF SW720 VIDEO/AUX ON—OFF DESCRIPTION POSITION SW4 PICKUP IN SW701 POWER ON/STAND-BY ON—OFF SW721 DISC 3 EJECT ON—OFF SW702 CLOCK ON—OFF SW722 DISC 2 EJECT ON—OFF DISC 1 EJECT ON—OFF SW703 TIMER/SLEEP ON—OFF SW723 SW704 TUNING/TIME UP ON—OFF SW724 DISC 1 ON—OFF SW705 TUNING/TIME DOWN ON—OFF SW725 DISC 2 ON—OFF SW706 REC/PAUSE ON—OFF SW726 DISC 3 ON—OFF SW707 REVERSE MODE ON—OFF SW727 EQUALIZER ON—OFF SW708 MEMORY/SET ON—OFF SW728 X-BASS/DEMO ON—OFF SW712 PRESET UP ON—OFF SWB101 CAM 1 ON—OFF SW713 PRESET DOWN ON—OFF SWB102 CAM 2 ON—OFF SW714 PLAY ON—OFF SWB103 CAM 3 ON—OFF SW715 STOP ON—OFF SWB104 CAM 4 ON—OFF SW716 REVERSE PLAY ON—OFF SWB105 CD EJECT ON—OFF SW717 CD ON—OFF SWB106 CD TRAY CLOSE ON—OFF SW718 TUNER (BAND) ON—OFF SWB107 CD IN ON—OFF ON—OFF SWB108 CD SET ON—OFF SW719 TAPE TYPES OF TRANSISTOR AND LED FRONT VIEW E C B (S) (G) (D) (1) (2) (3) KRC102 M KRC104 M KTA1266 GR KTA1271 Y KTA1273 Y KTA1274 Y KTC3199 GR KTC3194 Y KTC3203 Y 2SC1845 F FRONT VIEW B C FRONT VIEW E KTC2026 – 12 – SLR342VC XL-HP500 CAM2 CAM3 CAM4 3 2 1 SWB104 CAM4 CNP6 CAM1 4 SWB103 CAM3 TRAY 4 5 SWB102 CAM2 TRAY 3 6 SWB101 CAM1 TRAY 2 7 SWB108 CD SET 8 SWB107 CD IN 13 12 11 10 9 CNP5 SWB106 CD TRAY CLOSE 7 T_MOT_H/L 6 TRAY 1 5 CAM_M– 4 SWB105 CD EJECT 3 CAM_M+ CD RES 2 TRAY_M– CL 1 TO DISPLAY SECTION TRAY_M+ DI 1 DO 2 CE 3 DRF 4 WRQ +8V (+B4) 5 DGND (DRIVER) 6 +5V (+B7) DGND 7 TO DISPLAY SECTION +5V (+B8) AGND 8 L-CH CNP9 R-CH TO MAIN SECTION MOB1 MAIN CAM MOTOR – M + – M + 62 CLK LCHO RCHO 42 75 69 57 63 DI 56 64 DO 55 65 WRQ 51 50 66 RES 44 67 DRF IC1 LC78646E CD SERVO 43 40 37 28 19 6 48 XOUT XL1 16.9344 MHz MOB2 TRAY MOTOR 68 VDD5 45 61 CE 1 17 25 42 41 23 22 36 37 38 39 SLDO 23 9 10 LDD 8 LDS TIN1 7 TIN2 FIN2 41 46 FIN1 RVDD LVDD VVDD XVDD FDO 21 TDO 20 79 80 18 24 +3.3V IC2 M63001FP FOCUS/TRACKING/ VCC1 SPIN/SLED VCC2 DRIVER ~ ADAVDD 18 38 47 77 VDD RFVDD 5 35 40 VCC4 28 VCC3 SPDO 22 29 21 14 ~ 49 XIN +5V +3.3V 2 CONT5 26 8 Q2 4 ZD1 3.3V 5 6 7 15 16 26 27 LASER DRIVER +3.3V Q1 TRACKING COIL FOCUS COIL PICKUP UNIT +5V (+B7) CONSTANT VOLTAGE M1 SPINDLE MOTOR M2 SLED MOTOR Figure 13 BLOCK DIAGRAM (1/3) – 13 – + M – – M + SW4 PICKUP IN XL-HP500 17 13 MO/ST 8 18 7 16 12 20 L R 14 15 T306 +B6 X352 4.5 MHZ IC302 LC72131 PLL(TUNER) 1 20 +B5 FM+B Q361 CE DI CLK DO VT 22 15 16 OSC 11 FM/AM T303 AM OSC IN AM BAND COVERAGE 21 AM RF IN AM OSC OUT 24 23 AM TRACKING 4 5 9 VCO Q302 X351 456 kHz CF351 FM/AM 1 2 OSC BUFF T301 FM OSC 450 kHz CF352 T351 AM IF VCC FM RF L312 8 FM MPXIN DET 5 7 GND CF302 9 3 4 +B6 10.7 MHz +B6 FM/AM OUT AM IF T302 6 1 ZD351 5.1V STEREO 1 2 3 FM IF +B5 +B6 7 3 4 5 6 MO/ST FM/AM LOOP ANTENNA B.P.F BF301 IC303 LA1832S FM IF DET. FM MPX./AM IF AM MIX CNP302 IC301 TA7358AP FM FRONT END 9 10 17 21 +B5 Q360 FM SWITCHING +B5 JK690 VIDEO/AUX L AUX L 9 R R 16 TAPE L 10 R 15 L 11 TUNER R 14 CD L 12 R 13 BI901 8 7 6 AC BIAS L R 23 POP REDUCE 6 T1/T2 L REC 9 REC R REC 16 H/N +B5 IC101 AN7345K PLAYBACK AND RECORD /PLAYBACK AMP. SWITCHING Q105 Q114 Q106 SWITCHING +B5 Q111 L103 BIAS OSC BIAS MOTOR DRIVER Q113 SWITCHING ERASE HEAD REC/PLAY 7 L REC 18 R 11 12 NOR/ 13 15 HIGH T1/T2 Q112 Q603 Q604 SYSTEM MUTE 3 Q107 Q108 MUTING 4 L PB 21 R 2 21 R –20dB ATT Q601 Q602 4 L 7 18 8 17 P.B SWITCHING Q101~ Q104 IC601 LC75341 AUDIO PROCESSOR VF1 REC./P.B. HEAD REC. P.B. L-CH R-CH DI 1 CE 2 CLK 24 –VF CNP9 FROM CD SECTION 23 +B3 Q500 TAPE MECHANISM ASS'Y +B5 Q109 SWITCHING Q110 +B3 BIAS Figure 14 BLOCK DIAGRAM (2/3) – 14 – Q501 SOLENOID DRIVER C XL-HP500 FL701 FL DISPLAY 1 13 15 ~ 19 29 ~ 34 5 ~ 12 TO CD SECTION CNP6 35 ~ 41 14 45 +B9 TAPE MECHANISM ASS'Y Q701 +B10 91 68 ~ 56 42 46 40 25 13 30 VDD 38 72 ~ 39 IC701 +B10 IX0574AW AVDD 34 (To Serial No.211XXXXX) 33 IX0578AW (From Serial No.212XXXXX) 31 SYSTEM MICROCOMPUTER 37 78 RX701 REMOTE 1 SENSOR 2 3 79 VLOAD 80 CE CLK DI DO VDD 100 VDD ~ 90 92 93 1 2 4 5 6 7 8 9 1 0 11 12 Q702 TO CD SECTION CNP5 +B7 +B10 FAN MOTOR DRIVER Q906 SP DET. L 1 R 15 13 SYSTEM MUTE 41 16 1 7 20 21 22 23 24 RESET Q603 Q604 15 +B10 XL700 4.19403 MHz +B10 IC901 STK402-071 POWER AMP. Q901~ Q904 M M971(212-3) FAN MOTOR SO901 SPEAKER TERMINAL SP RELAY Q905 ON-OFF RL914 7 L-OUT 10 R-OUT 8 KEY SW701-SW708 SW712-SW728 – 86 RESET ~ ~ 85 +B10 +B3 JK951 HEADPHONES JK953 SUB WOOFER 9 C/PLAY -B2 IC851 KIA7812AP CONSTANT VOLTAGE REGULATOR D802 +B2 VF2 +B5 +B10 +B7 +B8 +B9 A_10V IC851 IC855 VOLTAGE REGULATOR IC852 PT801 MAIN POWER TRANSFORMER F801 4A 125V IC852 KIA7810AP CONSTANT VOLTAGE REGULATOR F803 2A 125V UNSW_5.6V D_5V A_5V SW_5V IC854 AN78L05 D803, D804 IC853 KIA7805AP RL841 F804 2A 125V IC853, IC854 CONSTANT VOLTAGE REGULATOR Q801 VOLTAGE REGULATOR T.F. AC POWER SUPPLY CORD AC 120 V, 60 Hz –VF BIAS VF1 +B3 +B4 M_+12.6V LD+8V F802 4A 125V D855 AC_RLY Q841 RELAY DRIVER D842~ D845 PT841 SUB POWER TRANSFORMER Figure 15 BLOCK DIAGRAM (3/3) – 15 – XL-HP500 IC901 STK402-071 POWER AMP. + –VCC CH2 OUT 9 10 12 C914 100/63 11 R920 0.22 (2W) C932 0.22 8 14 C908 470P 13 R922 100 R903 1K 7 R918 0.22 (2W) 6 OUT CH1 5 R925 22K C913 100/63 R919 0.22 (2W) 4 R917 0.22 (2W) 3 +VCC + – 2 +B CH2 – 1 C907 470P FM SIGNAL R-CH (2CH) (50 WATTS/CH) 15 R910 1K L-CH CH1 R912 820 A 3P C906 R908 56K 22/16 R904 1K R935 56K L R936 56K R C926 0.22 (ML) C927 0.22 (ML) C928 0.22 (ML) R937 56K R916 5.6K C929 0.22 (ML) R941 4.7 (1/2W) R940 4.7 (1/2W) R902 56K C904 0.001 C901 0.22/50 R901 56K C925 47/50 Q901 KTC3199 GR Q904 KTC3199 GR C903 0.001 C912 0.022(ML) R Q903 KTC3199 GR D907 DS1SS133 D906 DS1SS133 Q902 KTC3199 GR R911 C915 10/63 R915 5.6K L R R914 0.1 (1W) R923 1K C911 0.022(ML) C905 3P –B R924 1K 0.1 (1W) R907 56K C909 820 22/16 R913 D905 DS1SS133 B +B L C916 10/63 100 C910 R921 R909 1K C C902 0.22/50 FAN MOTOR 5V +B +B D LUG902(229) CHASSIS GND P18 2 - C TO MAIN PWB(2/3) +B E 1 2 3 BI801 L-CH R926 22K A_GND C948 2200/50 R-CH –B +B2 4 SP_RLY R927 22K C949 2200/50 UNSW_5.6V –B 13 3 1 18 19 20 C860 47/25 2 4 3 5 4 6 5 7 6 8 7 SUB_B +B C864 0.1(ML) +B 18V C856 3300/35 R857 3.3 (1/2W) +B 2 C855 0.1(ML) IC853 KIA7805AP +B 1 2 LUG903(229) D855 DS1SS133 CHASSIS GND C859 0.1(ML) IC854 AN78L05 +B C861 0.047 17 1 3 G 16 C852 22/50 +B 2 15 R854 22K D860 GD1N4004 CD_GND 14 C853 47/25 +B C858 0.1(ML) +B SW_+5V D853 DS1SS133 C857 47/25 A_+5V UNSW5.6V 3 R858 220 +B C862 10/50 +B 12 IC852 KIA7810AP +B +B 10 11 R856 C851 1 0.047 (1/2W) R860 220 D852 DS1SS133 D851 DS1SS133 D_+5V +B 1 3 D859 DS1SS133 R852 10K +B_PROTECT 9 D857 DS1SS133 +B CNS801 2 1 2 C854 0.1(ML) +B ZD852 DZ9.1BSB 3 R853 22K A_+10V 8 P18 2 - E, P19 9,10 - H TO MAIN PWB(2/3) F +B D856 DS1SS133 7 LD_+8V 12.6V +B IC851 KIA7812AP D858 DS1SS133 IC855 KTC2026 +B C865 10/50 M_+12.6V R859 22K 6 SP_DET C863 22/50 5 1 IC851,852,853,854 Constant Voltage Regulator CD_D_GND CD_A_GND M GND APRO_GND D_GND TAPE_A_GND H • NOTES ON SCHEMATIC DIAGRAM can be found on page 12. 1 2 3 4 Figure 16 SCHEMATIC DIAGRAM (1/11) – 16 – 5 6 XL-HP500 MAIN PWB-A1(1/3) 2 +B 1 D912 DS1SS133 R950 68K CNP971 +B RL914 R945 2.2K L +B R944 2.2K M_+12.0V SP_RLY R_CH GND R C927 0.22 (ML) M 1 HEADPHONES PWB-A3 JK951 HEADPHONES HD902 FW902 1 1 2 2 3 3 4 4 5 5 R962 330 (1/2W) R961 330 (1/2W) C643 0.001 L_OUT R_OUT L_CH 2 CNS971 WT902 C931 10/50 Q906 KTC3203 Y R947 15K R949 1K (1/2W) + M971 FAN MOTOR (212-3) C930 47/50 D911 DS1SS133 C929 0.22 (ML) 0.2V JACK PWB-A4 4.4V HD903 R946 1 1 2 2 3 3 + + L-CH – – L-CH_GND JK953 SUB WOOFER R965 8.2K (1/2W) R966 8.2K (1/2W) WT904 47K FW903 C960 3.3/25 Q905 KTC3199 GR R967 680 (1/2W) R941 4.7 (1/2W) R-CH SO901 SPEAKERS 6 OHMS MIN +B R-CH_GND LUG902(229) CHASSIS GND 6V 1 CNS801 2 1 3 2 4 3 5 4 6 5 7 6 8 7 P32 1 - A CNP801 TO POWER PWB 801 +B LUG903(229) CHASSIS GND 7 8 9 10 Figure 17 SCHEMATIC DIAGRAM (2/11) – 17 – 11 12 XL-HP500 220P C652 FM SIGNAL CD SIGNAL AUX SIGNAL C651 220P MAIN PWB-A1(2/3) A PLAYBACK SIGNAL RECORD SIGNAL R601 1K R602 1K IC601 LC75341 AUDIO PROCESSOR 1 DI 10K 1/50 4 C607 0.15 R607 3.3K C605 0.15 C611 C613 Q602 KTC3199 GR R616 2.2K R610 2.2K C631 RS LSEL0 8 C617 1/50 C619 1/50 C621 1/50 R LIN 7 C615 4.7/50 R612 390 Q604 KTC3199 GR C636 0.001 1/50 + – C R614 3.3K C638 0.001 R618 330 R-CH 3 LTRE 6 0.0022 RB LBASS 5 C635 0.001 + – R615 3.3K Q601 KTC3199 GR Q603 KTC3199 GR C637 0.001 A_GND 2 R611 2.2K R + – TO MAIN PWB(1/3) P16 1 - E 1 R617 2.2K V + – LOUT + – R619 330 CCB INTERFACE 3 VSS R613 390 L-CH CE 2 + – C609 + – R605 + – B L4 9 AUX L3 10 DECK 0.0047 L2 11 TUNER L1 12 CD C623 1/50 BI901 CNS9 +B 5 +B 4 3 2 +B 1 LD_+8V CD_D_GND 13 A_+5V 11 D_+5V 10 CD_D_GND CD_A_GND R149 3.4V 0V 2 3 0V 2 3.4V Q114 KRC104 M R112 0.7V 180P R105 3.3K 0V 0V Q101 2SC1845 F R103 2.2K 2 3 5 6 7 C109 0V 0V R113 1K C113 0.033 C111 100/16 C115 560P R115 56 R107 47K R111 R123 6.8K 56K 8 9 15K • NOTES ON SCHEMATIC DIAGRAM can be found on page 12. 2 3 4 Figure 18 SCHEMATIC DIAGRAM (3/11) – 18 – 5 220/10 22/16 C134 C133 10K C132 47/25 16 56K H 1 R134 100 C130 0.0033 R132 17 15 14 ALC Nor/CrO2 ALC RIPPLE 18 – + Hich=CHROME + – 4 R117 R119 330P 100K 3.9K 4.7K R126 R150 68K SPARE C118 47/25 560P 1 0V 0.7V 19 10 6 11 IC101 Q103 2SC1845 F 20 C131 47/25 C103 21 – 112K + Hich=T1 + 112K – R135 10K G 22 T2_L2 0V HEAD PLATE BLOCK(210-1) 23 T2_L1 C126 22/16 C129 0.0033 1 24 R128 5.6K 100 2 0.7V C127 0.022 3 1 100K 3.9K R127 4.7K C123 270P 2 1 T2_R1 C110 330P R118 R120 R114 1K 3.3/50 2 Q104 2SC1845 F 0V C143 4 0V 0.022 5 3 A_GND C104 180P C121 4 3 T2_R2 0V R106 3.3K R124 6.8K C117 47/25 4 0.7V R122 12K C114 C116 0.033 560P R121 12K 6 ERASE M_GND C106 5 7 560P R-CH L-CH RECORD/ PLAYBACK HEAD 5 6 C112 100/16 C105 6 0V Q105 KTC3199 GR 8 ERASE HEAD 2.2K 4.7K 0V R116 56 R108 47K R104 0.7V Q106 KTC3199 GR BI102 0.7V 0V Q102 2SC1845 F R110 0V K R139 10K 15K 4.7K TAPE MECHANISM Ass'y(210) R109 F 220K R138 10K 1.5K Q112 KTA1266 GR R136 REC_R 1 R130 9.3V 3 0V 1 R148 4.7K C128 0.022 8.6V C125 22/16 9.3V R133 R147 10K 150 C141 100/16 R131 1.5K R146 10K Q113 KRC104 M Q108 KTC3199 GR 16 270P 15 C124 TO MAIN PWB(1/3) P16 1 - F~G 7 E C642 0.001 R129 5.6K LD+8V 18K 6 C625 100P 1 A-5V 18K R646 10K 2 D_5V D_GND 7 R645 R609 3 C641 0.001 C639 2.2/50 4 D CD_GND 8 R621 22K 5 L-CH 22K 6 P31 11 - D CNP9 TO CD SERVO PWB A_GND 9 R620 7 R-CH C640 22/50 8 XL-HP500 R693 39K 4 R691 6.8K C691 390P 3 R690 6.8K C690 390P 2 L-CH JK690 VIDEO/AUX 1 R-CH R692 39K C653 220P CLK VREF + – CHASSIS GND C603 22/16 22 C610 1/50 C608 0.15 21 CE R604 10K A_+10V + – ROUT R603 1K 24 VDD 23 + – E C602 0.022 C601 220/16 + – RBASS RTRE RIN 20 19 18 R4 R3 K R2 ER R1 D R606 3.3K C606 0.15 28 +B 21 D_GND 22 C614 1/50 C612 0.0022 D1 C616 4.7/50 27 CLK 17 30 TUN_R C618 1/50 + – RSEL0 X GND TO MAIN PWB(3/3) P21 11 - H 601 5341 OCESSOR 16 24 C632 0.0047 C620 1/50 15 25 C622 1/50 14 R642 C624 1/50 TUN_L 10K 26 DO 13 29 R641 100P 10K C626 R608 10K TO DISPLAY PWB P22 2 - F CNP701A R137 220K R136 220K Q107 KTC3199 GR R139 10K 0V 16 C135 0.022 220/10 16 C134 22/16 C133 10K C132 47/25 DO 15 CE R158 220 13 11.6V 12 +B_PROTECT 11 3 D_GND R141 4.7K 10 1 R142 82 (1/2W) S_MUTE 0V 0V REC/PLAY R145 4.7 SW_5V 8 7 M_+13V 0V 6 5 SP_RLY 3 SP_RLY –20dB CNP701B 17 20 18 8 9 19 6 12 14 4 SP_DET SP_DET UNSW5.6V SW_+5V M_+12.6V D_GND +B_PROTECT UNSW5.6V A_+10V C138 0.0082 APRO_GND R144 22K 9 T_BIAS TAPE_A_GND R143 47K Q111 KTC3203 Y 12 2 L103 330µH R135 10K C129 0.0033 11 Q109 KTA1266 GR C139 0.039(ML) 10 C131 47/25 9 IC101 VCC AN7345K PLAYBACK AND RECORD/ PLAYBACK AMP. 6K 6K 0V DI Q110 KRC104 M 0V 11.6V 13 C137 0.047(ML) 15 14 ALC Nor/CrO2 ALC RIPPLE 16 14 CLK M_GND C130 0.0033 R134 0.7V C140 47/25 8 K R140 47K R 5 2 1 1 FC701 4 TO MAIN PWB(1/3) P16 1 - E~H 7 8 9 10 Figure 19 SCHEMATIC DIAGRAM (4/11) – 19 – 11 12 XL-HP500 C323 0.022 B D301 DS1SS133 R358 3.9K +B C334 22P (UJ) AM OSC IN AM MIX OUT 1 AM BAND COVERAGE fL 1 2 R323 68K FM ANTANNA D 0.022 2 C350 T306 6 4 5 3 VD301 SVC348S C335 560P 23 FM IF IN AM OSC OUT 24 10/16 1 C332 0.022 C352 1 C331 0.047 R351 5.6K 2 C330 15P (UJ) 0.022 3 2 1 C351 3 5 6 R336 10K C 2 D302 DS1SS133 CNP302 AM LOOP ANTANNA 3 T303 4 C342 0.022 AM TRACKING fL C361 AM SIGNAL 22 FM AFC FM SIGNAL C362 R365 3.3/50 10K A FM FRONTEND IC301 TA7358AP 9 R382 150 C313 22P (CH) VD303 SVC211C C317 0.001 C316 0.022 C315 0.0047 C314 0.0047 R322 680 47K C318 100P D303 DS1SS133 R375 470 R316 4.7K Q361 KTA1266 GR Q302 KTC3194 Y C384 0.001 +B R327 33 C302 0.001 D304 DS1SS133 H • NOTES ON SCHEMATIC DIAGRAM can be found on page 12. 1 2 3 4 Figure 20 SCHEMATIC DIAGRAM (5/11) – 20 – 5 6 4 1K R372 DI 3 1K 2 IC302 LC72131 PLL(TUNER) C322 100P R325 1 R373 2 22 21 20 1K T302 FM IF C382 15P (CH) X352 FM RF R311 100K C312 0.022 3 C381 12P(CH) C393 C390 120P 100P 4.5MHZ X IN X OUT VSS AOUT CE R309 10K T301 FM OSC 1 C 1 C389 R38 1/50 1.5K R314 22 G C394 47/16 C397 0.022 R381 10K C307 10/16 R374 8 TP301 7 C310 15P(CH) VD302 SVC211C C308 4.7P (CH) C309 0.001 L312 1SS133 D305 F 6 C305 4.7P (CH) E CHASSIS GND 5 CF302 FM IF C304 0.01 4 C324 4.7P (UJ) 3 +B C311 C306 18P 0.022 2 R302 10 1 R313 33K 1 2 3 C303 10P(CH) BF301 7 6 9 10 11 8 +B C386 330P R395 47K R359 1.8K R376 1K 9 C391 47/16 C356 0.001 C370 1/50 C357 2.2/50 IF OUT PHASE L-CH OUT PHASE MO/ST (FM/AM) R-CH OUT VCC MPX IN FM DET MPX VCO STEREO 12 C358 1/50 R355 3.3K L352 100µH C396 100/10 C395 0.022 TP302 C369 27P (UJ) 3.9K C373 0.027 C374 0.027 C368 R356 R357 470K 1/50 1K X351 456KHZ R363 3.9K C366 0.001 C365 0.022 C364 2.2/50 C363 0.022 C361 0.022 C362 R365 3.3/50 10K C367 R350 1/50 2.7K IC303 LA1832S FM IF DET./FM MPX./AM IF R364 22P C355 3 R388 3.9K C398 100/10 C399 0.022 270 R353 SD FM/AM OUT GND VSM AM IF IN AM LOW CUT 10 11 R360 4.7K 82K 21 22 Figure 21 SCHEMATIC DIAGRAM (6/11) – 21 – 10 24 25 11 26 27 28 29 CLK 5 9 DO R390 8 CE 4 8 7 15 14 13 DI 3 7 6 16 R385 5.6K R377 47K L351 100µH R387 5.6K AM IF R384 5.6K C380 10/16 5 C354 0.022 CF351 FM IF 10.7MHZ R393 1K 2 C353 0.022 1 CF352 R352 1K AM RF IN REG 4 17 C338 0.001 MO/ST SD IF IN T351 C385 0.01 C387 0.022 AM OSC IN AM MIX OUT FM AFC FM IF IN AM OSC OUT 3 C388 0.001 FM/AM C389 R380 1/50 1.5K R379 2.2K 0.022 20 19 18 ST IND DO FM/AM VDD FM IN IF CONT AM IN C394 47/16 C392 0.001 C350 2 21 TUN_L 4.7K R378 AIN PD CL R381 10K 1 22 C372 R362 1/50 2.2K TUN_R 1K R372 DI 19 18 17 16 15 14 13 12 AOUT 23 C371 1/50 D_GND 1K R373 20 CE 24 A_+10V 1K R374 XL-HP500 MAIN PWB-A1(3/3) R361 2.2K +B ZD351 DZ5.1BSB R392 R391 270 Q360 KTA1266 GR 270 R383 5.6K +B R386 10K +B 30 TO MAIN PWB(2/3) P19 12 - C 12 XL-HP500 A P01 P02 P03 P04 P05 NX NX NX NX NX NX NX NX NX P06 P07 P08 P09 P10 P11 P12 P13 P14 P15 P16 P17 P18 NP NP F2 F2 R766 1.5 FL701 FL DISPLAY TRY 1 SW T_MOT H-L 10 11 12 13 R763 47K 9 C MOT– C MOT+ T MOT– S1 77 S13 76 S14 75 S15 74 S16 73 DIST 1/S17 D701 DS1SS133 72 DIST 0/S18 IC IX05 (To Serial N 71 C 70 DIST IN D S2 78 S12 D703 DS1SS133 T MOT+ CNP7A FC6 13 81 82 83 84 85 86 87 88 89 90 S10 80 S11 79 VLOAD Q701 KTC3319 GR TRY 2 SW 7 8 TO CD SERVO PWB C707 1/50 TRY 3 SW C706 6 R764 1K S3 0.001 C708 TRY 4 SW S4 0.001 C709 CAM 1 SW 5 S5 0.001 C710 4 100K S6 0.001 C711 CAM 2 SW S7 0.001 C712 3 R765 S8 0.001 C713 2 CAM 3 SW 33 P25 10 - B CNP6 CAM 4 SW R762 B 1 S9 0.001 C714 1 47/25 0.001 C715 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 R761 10K R756 1K R760 10K R755 1K R759 R758 10K 10K R754 1K R753 1K R757 10K R752 1K R767 5.6K R751 1K R768 5.6K R750 1K R769 5.6K R749 1K R770 5.6K R748 1K R771 5.6K R747 1K R772 5.6K R746 1K R773 5.6K R745 1K R774 5.6K R744 1K 69 68 T_MOT H-L IX05 (From Serial N 67 T MOTOR+ 66 T MOTOR– 65 C MOTOR+ SYS MICROCO 64 C MOTOR– 63 TRAY 4 SW 62 TRAY 3 SW 61 TRAY 2 SW 60 TRAY 1 SW 59 CAM 4 SW 58 CAM 3 SW 57 CAM 2 SW 56 CAM 1 SW SMUTE 51 T_SOL_A T1 RUN 52 VDD JOG 1 53 T_MOTOR 54 TIMER LED 55 1K 1K 1K 560 2.2K 680 680 1K R736 R735 R734 R733 R732 R731 R730 JOG 2 E R737 MIC SW 50 49 48 47 46 45 44 43 42 41 FC701 16 16 DO 15 CE 14 CLK 13 DI 12 P19 12 - G CNP701B TO MAIN PWB(2/3) FPA/FPB +B_PROTECT 11 D_GND 10 9 REC/PLAY 7 M_+13V SW_5V 6 UNSW5.6 SP_DET 4 SP_RLY 2 –20dB 1 +B +B +B + 3 R780 10K N.C. (OP PACK) F. REC R. REC 3 4 5 6 FC702 7 R506 10K Q501 KTA1271 Y R507 10K R504 4.7K R505 8.2K TAPE MECHANISM PWB Ass'y(210-3) TAPE MECHANISM Ass'y(210) H • NOTES ON SCHEMATIC DIAGRAM can be found on page 12. 1 2 3 4 Figure 22 SCHEMATIC DIAGRAM (7/11) – 22 – 5 6 0.001 2 C717 M_+13V +B 1 3 10K D500 DS1SS133 – 1 2 Q500 KTA1273 Y CNS702 T1 RUN 1 GND 2 T_SOL_A 3 T_MOTOR 4 5 FPA 6 FPB 7 C502 47/25 M + TAPE MOTOR (210-2) END SW –COM +SOL +MTR VR701 VOLUME R781 0.001 CNP701A SOLENOID G +B +B C716 5 R782 8 R799 1 S_MUTE T_BIAS 10K F XL-HP500 DISPLAY PWB-A2 G10 G4 G3 G2 G1 NP NP F1 F1 6 5 4 3 2 1 G6 7 G7 8 G8 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 G9 G5 P01 P02 P03 P04 P05 NX NX NX NX NX NX NX FL701 FL DISPLAY C700 1/50 70 DIST IN 69 IX0578AW (From Serial No.212XXXXX) SYSTEM C MOTOR– MICROCOMPUTER TRAY 4 SW 66 T MOTOR– 65 C MOTOR+ 60 TRAY 1 SW 59 CAM 4 SW 58 CAM 3 SW 57 CAM 2 SW 56 CAM 1 SW R795 1.5 C703 15P VDD 16 R710 CD_CLK 17 CD_DI 18 R711 R712 CD_DO 19 R713 CD_CE 20 CE 21 R714 CLK 22 R715 DI 23 R716 DO 24 R717 62 TRAY 3 SW 61 TRAY 2 SW R794 10K 1K R708 R793 10K XL700 X1 12 4.19403 MHz VPP/IC 13 C704 XT2 14 18P 1K R709 CD_DRF 15 67 T MOTOR+ +B 1K 1K 1K 1K 1K 1K CNP5A CD RESOUT 1K 1K CD_CLK CD_DI AVSS 25 55 CD_DO CD_CE FPA/FPB SW 28 PROTECT 29 AVDD NO USE 30 BI706 VF2 P_IN 5.6K VF1 AC_RLY CON 1K 7 FC5 7 6 P25 9 - B CNP5 TO CD SERVO PWB 5 4 3 2 1 1 1 CNS706 2 1 3 2 4 3 5 P32 1 - D CNP706 4 TO POWER PWB 6 5 D708 DS1SS133 R723 1K R724 1K R725 1K –VF R790 R721 KEY 2 KEY 1 KEY 0 1K R726 1K R727 1K R728 1K R729 1K R730 680 R731 680 R732 2.2K R733 560 R734 1K R735 1K R736 1K R737 JOG 2 CD_DRF CD_WRQ 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 MIC SW 1K R720 0.022 AVREF CD_WRQ P_IN 27 SP DET REMOCON VSS SMUTE 51 T_SOL_A T1 RUN 52 VDD JOG 1 53 T_MOTOR 54 TIMER LED 26 C705 63 +B G1 RESET 10 X2 11 68 T_MOT H-L 64 G2 G3 G5 G6 G7 G8 G9 G10 S1 S2 S3 S4 G4 9 IC701 IX0574AW (To Serial No.211XXXXX) 71 C701 220/10 +B D706 DS1SS133 UN_SW5.6V +B R797 100K C718 0.01 1 +B RX701 REMOTE SENSOR C719 3.3/50 Q702 KRC102 M 2 3 D707 DS1SS133 R796 47K +B 10K R783 4.7K R782 DS1SS133 R798 100 1 C720 +B D705 +B 100µH 2 3 0.022 5V BACK UP 10K C722 150P L701 R789 D709 DS1SS133 72 DIST 0/S18 S5 S6 S7 S8 S9 C702 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 0.022 S10 80 S11 1 1K R700 VDD 79 VLOAD 2 –20dBATT 78 S12 3 1K R702 T-BIAS 4 77 S13 1K SP_RLY 5 R703 76 S14 1K R704 T_REC/PLAY 6 75 S15 1K R705 CD_RESOUT 7 74 S16 1K R706 AC_RLY 8 73 DIST 1/S17 C721 47/25 R784 R780 10K 10K RD19 VR701 VOLUME 2 0.001 0.001 C716 K LED701 SLR342VC 1 3 C717 1 R785 10K KEY 2 680 SW721 DISC 3 R786 RD11 KEY 1 10K R787 10K 8 RD23 RD24 RD25 1.5K SW724 2.2K SW725 2.7K SW726 3.9K SW727 SW728 DISC 3 EQUALIZER X-BASS /DEMO DISC 1 DISC 1 RD12 RD13 DISC 2 RD14 RD15 RD16 RD17 RD18 820 1K 1.5K 2.2K 2.7K 3.9K 5.6K SW713 SW714 SW715 SW716 SW717 SW718 SW719 SW720 PLAY REVERSE STOP PLAY CD TUNER (BAND) TAPE VIDEO /AUX PRESET RD01 RD02 RD03 RD04 RD05 RD06 680 820 1K 1.5K 2.2K 2.7K 3.9K SW702 SW703 SW704 SW705 SW706 SW707 SW708 REVERSE MODE MEMORY /SET SW701 9 DISC 2 RD22 680 POWER ON/STAND BY 7 RD21 820 1K SW722 SW723 SW712 PRESET KEY 0 RD20 CLOCK TIMER/ SLEEP TUNING TUNING /TIME /TIME REC/PAUSE 10 Figure 23 SCHEMATIC DIAGRAM (8/11) – 23 – RD07 11 12 XL-HP500 A CD SERVO PWB-C C34 100P C33 0.022 C32 100P C30 100P C28 100P C27 0.022 CD SIGNAL 1 C6 0.1 Q1 KTA1266 GR CNP1 TP3 C4 0.001 +B C2 0.01 C1 47/25 C 80 79 78 77 76 75 74 73 72 71 70 1 SLCO 2 SLCIST C55 3 EFMIN 4 RF R12 330 C8 0.0027 5 RFVDD 6 RSVSS 0.022 C50 22P(CH) 4 4 4 4 5 5 5 5 6 6 6 6 7 7 7 7 8 8 8 8 FO– GND PD VR C38 0.01 LD 5 5 + 4 4 4 4 3 3 3 3 2 2 2 2 1 1 1 1 PU-IN 16 15 14 13 12 11 10 9 8 7 6 5 4 FD 17 FO+ 18 FO– 19 3 2 R18 1K R16 1K R15 1K R44 STANDBY VCC 20 1 R20 10K SL+ SL– PUIN IC2 M63001FP FOCUS/TRACKING/ SPIN/SLED DRIVER GND + SW4 PICKUP-IN 21 CNP3 5 MUTE SP– + 5 M– SP+ 6 VREF 6 C40 220/6.3 CNS3B 6 + – M2 SLED MOTOR 6 – CNP3A M CNS3A M1 SPINDLE MOTOR + 1 6 2 21 22 23 24 25 26 27 28 29 30 31 R14 1K +B C39 100/10 E 18 ADAVDD 19 ADAVSS 20 TDO 4 CNP2 TR+ GND C11 15 TE 0.22/50 16 RFMON C12 17 JITTC 100P +B 18 19 C54 20 0.022 FO+ FDO 3 12 REF1 13 FE 14 TEC R13 1K 2 3 TR– LD 2 3 GND VR 2 3 C53 0.001 C52 0.001 PD TR– 2 TR+ SL– FO– 1 SL+ FO+ FO+ 1 C19 3.3/16 OS-CON SLDO TR+ 1 TR– IC LC786 CD SE 10 TIN2 F 11 VREF 12K D 1 CNS2B TR+ CNS2A TR– C10 10/50 C9 100/10 8 7 5 7 FIN1 A 8 FIN2 B 9 TIN1 E TP1 TP2 CONT3 1 FSEQ 1 R39 C35 680 0.047(ML) 1 C5 0.047 R10 27K CONT2 22K V/1P R3 DEFECT F C37 2 R40 680 2 VVSS 2 CONT5 8.2K 2 R41 12K R4 VVDD B PCKIST 8.2K 3 SLDO GPDAC CONT4 R5 3 R42 1.2K A 3 LDS 4 3 FR 5 4 LDD 5 4 SPDO 5 4 0.1 +B 5 C C36 0.22/50 22K PDO1 R6 E PDO2 VREF SBCK/FG 6 TO C 7 6 R11 F 7 6 10K B 7 6 C3 47/25 A 7 R9 10 VREF E +B +B VCC R1 8.2K VCC R7 47 R2 8.2K B CNS1B CNS1A PICKUP UNIT(306) R46 2.7K F + + + CD MOTOR PWB-D 31 32 33 34 35 37 M– 38 +B +B 39 40 41 42 CAM_M+ C41 100/10 G 36 TRAY_M– 30 VCC4 29 M+ 28 CAM_M– SP+ 27 VCC3 26 SP– 25 SPO 24 VCC2 23 TRAY_M+ + – + 22 C43 100/10 +B R49 1 +B R50 1 CAM_M+ CAM_M– H • NOTES ON SCHEMATIC DIAGRAM can be found on page 12. 1 2 3 4 Figure 24 SCHEMATIC DIAGRAM (9/11) – 24 – 5 6 XL-HP500 1 1K DI R33 1K CL R32 1K CD RES +B 0.022 7 6 4 3 2 1 5 CNP6 1 2 2 3 3 3 4 4 4 5 5 5 ASLRCK 55 IGMOUT 54 1 1 2 2 EFLG 53 C2F 52 XVSS 51 3 3 4 4 5 5 6 6 DI XL1 16.9344MHz R43 220 TEST 41 C22 R18 1K C16 330/6.3 C23 10/50 R24 1.5K 0.01 C14 100/10 C24 10/50 R25 1.5K C59 0.01 +B C42 0.01 +B +B C48 0.022 R27 10K R26 10K SWB101 CAM1 SWB102 CAM2 SWB103 CAM3 SWB104 CAM4 CNS8 8 R-CH 7 AGND 6 L-CH 5 DGND 4 +5V 3 +5V 2 DGND 1 P22 2 - D CNS9 FROM MAIN PWB (2/3) +8V CNP9 C51 0.022 +B Q2 KTC3203 Y +B R20 10K SWB105 CD EJECT SWB106 CD TRAY CLOSE SWB107 CD IN SWB108 CD SET +B C26 0.0015 C25 0.0015 CNP8 +B R22 100 ZD1 DZ3.3BSB LVDD C44 0.001 VDD DOUT 5 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 R31 2.2K 11 10 LVSS 43 LCHO 42 VSS MON15 MON14 MON12 MON13 MON11 FSEQ V/1P 12 XVDD 47 RVDD 46 RCHO 45 RVSS 44 C13 0.022 BIM2 1 FSX/16MIN 50 XIN 49 XOUT 48 9 SWITCH PWB-E 2 60 DATA BCK 59 LRCK 58 ASDFIN 57 ASDACK 56 3 18 ADAVDD 19 ADAVSS 20 TDO DEFECT 7 1 CL CE DO vRES vWRQ VSS VDD5 DRF CONT3 CONT2 PDO1 8 R29 2.2K R30 2.2K IC1 LC78646E CD SERVO SBCK/FG 13 12 11 10 9 L1 0.82µH C36 0.22/50 R39 C35 680 0.047(ML) R40 680 VVSS PDO2 1 R28 2.2K R52 4.7K 8 7 CONT5 7 +B 6 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 1 6 13 6 CNP5 C27 FC6 5 CNP7 100P C28 4 CNS7 R34 100P C30 3 CAM4 DO CAM3 CE 1K CAM2 1K R35 CAM1 R36 TRAY 3 TRAY 4 100P TO DISPLAY PWB P22 2 - B CNSP7A TO DISPLAY PWB CNP5A P23 11 - D 2 TRAY 2 C32 FC5 1 T_MOT_H/L DRF TRAY 1 WRQ 1K CAM_M– 1K R37 CAM_M+ R38 0.022 TRAY_M– 100P C33 TRAY_M+ C34 +B R51 3.3 R47 C18 100/10 R23 220 100 ZD2 DZ3.9BSB R46 2.7K R45 2.7K +B +B MOB2 TRAY MOTOR R49 1 CNP4 +B R50 1 4 4 3 3 2 2 1 1 CNS4 – + M – + M MOB1 MAIN CAM MOTOR • The numbers 1 to 12 are waveform numbers shown in page 34. 7 8 9 10 Figure 25 SCHEMATIC DIAGRAM (10/11) – 25 – 11 12 XL-HP500 TO DISPLAY PWB P29 11 - E CNP701A A FC701 16 1 MAIN PWB-A1 C322 C358 C355 R619 C640 R616 C638 R620 R615 R901 C909 C903 C932 C914 R903 R927 R921 R926 1 R925 R912 R904 CHASSIS GND H 2 3 4 Figure 26 WIRING SIDE OF P.W.BOARD (1/7) – 26 – 5 6 R917 R919 R918 R920 R914 C927 R908 LUG902(229) HD903 3 C906 C929 R940 D911 1 FW903 2 1 IC901 RIGHT 3 R90 15 14 13 12 11 10 9 8 7 6 5 4 R941 SO901 SPEAKERS R967 R966 R965 G C908 R910 LEFT WT904 RL914 1 Q603 R604 Q601 R915 C901 C915 R936 R922 3 2 1 JK953 SUB WOOFER C635 C637 Q604 C911 R923 E C B B C E HEAT SINK GND F C960 R613 Q602 E C B R617 R362 C371 C636 E C B Q901 R353 C357 C368 R610 E C B D907 D905 R935 R611 R357 R945 R944 C912 Q902 R614 C639 Q903 B C E D912 JACK PWB-A4 C396 R391 R386 C365 R621 C364 R612 C363 R618 R902 C902 C910 R947 E C B C374 C372 C916 R946 X351 R351 R358 C342 C361 FM RF E C B C925 C312 C313 C305 R314 R322 FM IF R325 R950 Q905 E C B R937 CHASSIS GND B C E C931 R916 C691 R691 R363 R361 R364 C373 R356 D906 CNS971 R949 R924 Q904 C690 BR R350 C926 2 1 Q906 RD R690 C930 R693 E C356 TP302 C928 RED C369 C367 C388 R355 C351 C399 C366 IC303 R692 LEFT C354 C353 T306 AM BAND COVERAGE fL 1 2 CNP971 RIGHT TP301 C334 C332 R323 C338 T303 C330 AM TRACKING fL C335 C331 C370 24 23 22 21 20 19 18 17 16 15 14 13 VD301 M971(212-3) FAN MOTOR L352 ZD351 CF351 C904 GND JK690 VIDEO/AUX C352 C350 R352 R309 C362 C323 D R395 VD302 R311 L312 D305 R313 R365 C317 R316 1 2 3 BF301 C395 1 2 3 4 5 6 7 8 9 10 11 12 C316 D302 C311 R376 T302 CF302 C308 C309 1 2 3 R336 D301 C303 C315 IC301 C304 CNP302 3 2 1 3 2 1 AM LOOP ANTENNA B C E R327 R302 C310 C314 C306 Q302 9 8 7 6 5 4 3 2 1 R382 CF352 3 2 1 T301 C324 AM IF VD303 FM OSC C389 FM ANTENNA B C E R375 C307 C L351 C385 R381 R377 R388 T351 R383 C391 R385 R392 C393 C394 22 21 20 19 18 17 16 15 14 13 12 C392 C380 R380 C397 R379IC302 C387 R393 C386 R387 Q360 R384 R360 R359 1 2 3 4 5 6 7 8 9 10 11 C382 C381 Q361 R378 R372 C398 R373 R374 X352 C390 C318 C384 D303 D304 CHASSIS GND B R390 E C B C302 XL-HP500 TAPE MECHANISM Ass'y(210) RECORD/PLAYBACK/ERASE HEAD Q108 C118 13 IC101 15 1 C103 BI102 C106 1 20 24 C105 R114 8 Q104 R145 L103 C139 COLOR TABLE R112 BR R106 CNS9 WH GY WH GY WH GY WH RD R141 R144 C140 3 2 1 Q109 R142 E C B B C E Q111 RD R140 WT902 C865 C858 R852 C859 R907 ORANGE YL YELLOW GR GREEN BL BLUE VL VIOLET GY GRAY WHITE BK BLACK PK PINK 1 FW902 1 C852 1 2 3 D858 R857 R911 C907 C857 HD902 C861 C862 C851 D855 C853 RED OR WH(W) IC854 5 E C B C860 R858 R860 C905 C913 R859 ZD852 IC855 C909 R903 D857 D852 R856 D851 D860 D853 BROWN RD(R) HEADPHONES PWB-A3 C643 C863 8 7 6 5 4 3 2 1 R143 5 4 3 2 1 C642 R619 C638 1 BK 1 2 3 4 5 6 R962 BI901 R605 Q110 E C B E C B BL YL WH PK BK WH GY CNP9 TO CD SERVO PWB P30 4 - B 15 13 11 9 7 5 3 1 CNP701B R149 WH C641 GY WH GY WH GY WH R105 Q103 R103 E C B Q101 R104 E C B Q102 E C B C141 R148 YL WH BK PK BK WH C114 C137 3 2 1 E C B Q106 BL R961 16 14 12 10 8 6 4 2 1 2 3 E C B C116 R120 5 9 C112 R118 C110 C138 C104 R111 Q114 R645 Q113 R616 12 C111 C610 R601 R603 R646 R108 C620 C632 R606 R124 R115 R147 C618 C109 R113 R642 C126 R116 1 R121 R123 C117 R119 C115 R117 C113 R146 C622 1 R130 C128 R126 R128 C124 R150 10 C121 R107 C616 5 13 15 C612 C608 C606 C624 R109 Q105 5 20 R127 6 C130 C135 C129 C125 R131 R129 C123 C143 R110 10 1 12 R608 C614 C601 R135 C131 R133 R137 R609 C625 C602 24 C603 R602 C623 IC601C626 C652 C653 Q107 C607 C611 B C E Q112 C621 HEAD PLATE BLOCK(210-1) R122 R132 C133 C127 R139 C617 C613 C651 R134 C132 R158 R138 C605 C609 R607 C619 C615 R136 B C E C134 8 R641 C631 JK951 HEADPHONES D856 R854 D859 C854 R853 C864 C855 3 2 1 3 2 1 IC852 IC851 GY WH GY WH GY WH RD 8 3 2 1 IC853 7 6 5 4 3 2 1 1 C856 C949 C948 R913 R917 BI801 2 1 CNS801 CNP801 TO POWER PWB P32 2 - G R909 LUG903(229) CHASSIS GND 7 8 9 10 Figure 27 WIRING SIDE OF P.W.BOARD (2/7) – 27 – 11 12 XL-HP500 A TO CD SERVO PWB P30 3 - B CNP5 FC5 B C E SW723 1 1 2 BI706 R766 CNS702 6 1 Q500 R731 R735 R733 R737 50 40 RD11 E C B R736 51 60 45 55 R726 R714 R715 R505 E C B SW720 VIDEO /AUX RD18 2 4 6 1 3 5 7 1 R716 R732 R793 R795 2 C502 R507 C721 3 D500 Q501 R504 RD23 RD25 SW728 X-BASS /DEMO C716 C717 R780 D709 RD R725 RD12 SW719 TAPE SW714 PLAY D708 R790 C706 R797 RD24 E D706 Q702 3 2 1 C718 SW727 EQUALIZER SW712 PRESET R789 D707 R796 VR701 VOLUME D705 R799 R781 R798 R SW713 PRESET C705 R724 R727 R729 R720 R721 C719 31 15 85 20 75 25 IC701 70 35 65 R723 D R785 D703 81 80 C703 XL700 C704 30 90 5 95 1 1 R704 2 R706 R703 R762 R700 R708 SW721 L701 R705 C722 3 C701 RD19 R764 C702 100 C720 R712 R711 R710 R709 SW722 3 SW726 RX701 R702 R713 CNP5A 7 5 3 1 6 4 2 2 29 30 31 32 33 34 35 36 37 C700 REMOTE SENSOR RD21 SW725 FL701 FL DISPLAY 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 R765 RD20 SW724 C Q701 10 RD22 B DISPLAY PWB-A2 1 7 R786 DISC SELECT R506 SW70 7 M 7 COLOR TABLE G BR BROWN RD( R) RED OR ORANGE YL YELLOW GR GREEN BL BLUE VL GY FC702 RD WH GY WH GY F 1 2 345 1 1 CNS706 CNP706 VIOLET TO POWER PWB P32 2 - F GRAY WH( W) WHITE BK BLACK PK PINK SOLENOID TAPE MECH H 1 2 3 4 Figure 28 WIRING SIDE OF P.W.BOARD (3/7) – 28 – 5 6 XL-HP500 TO CD SERVO PWB P30 4 - E CNP6 FC6 R772 D701 R760 R757 R754 R753 R755 CNP7A R752 LED701 R748 SW703 R746 R744 RD04 RD03 RD01 RD02 SW702 RD05 SW704 SW705 R782 R784 1 FC701 R783 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 16 SW707 RD06 RD07 SW708 MEMORY /SET SW706 REC/PAUSE REVERSE MODE 1 SOLENOID CNP701A RD15 SW718 TUNER (BAND) SW717 CD RD16 RD17 R730 STOP SW716 REVERSE PLAY R725 RD12 SW719 TAPE SW714 PLAY SW715 R717 RD14 CNP701B R794 TUNNING/TIME 7 TAPE MECHANISM PWB Ass'y(210-3) TAPE MOTOR (210-2) TAPE MECHANISM Ass'y(210) 7 8 9 10 Figure 29 WIRING SIDE OF P.W.BOARD (4/7) – 29 – 11 12 TO MAIN PWB P27 7 - D R728 RD13 R726 R787 R745 R735 R733 R736 R737 R731 RD11 R750 R734 SW713 PRESET SW720 VIDEO /AUX RD18 R747 R751 51 50 R786 40 45 55 60 R749 R724 C711 R774 R768 C713 R770 C715 R759 13 11 9 7 5 3 1 12 10 8 6 4 2 CLOCK D703 C710 R773 C709 R756 R761 R758 SW701 44 45 TIMER/ SLEEP 29 30 31 32 33 34 35 36 37 38 39 40 41 R763 R767 C712 R771 13 C707 FL701 FL DISPLAY C714 R769 C708 1 POWER ON/ STAND-BY LAY PWB-A2 XL-HP500 A TO DISPLAY PWB P28 2 - C CNP5A C37 R7 R42 C1 R11 C50 R4 R1 R6 R3 1 IC2 1 2 3 4 5 6 10 15 21 CNP3 C40 20 C59 R22 C23 50 45 35 30 R24 R26 C25 C22 C44 C14 41 40 C13 11 10 9 6 1 20 21 2 R20 R18 R16 R15 R14 R13 C11 C19 42 R50 C43 35 C39 C48 L1 R25 12 C9 40 5 R43 C54 4 C52 C12 CNP1 IC1 10 15 25 C10 R2 5 1 C53 R5 R32 R35 C55 R12 C8 70 75 C18 C24 65 55 C6 R49 Q2 B C E R27 61 60 80 R47 ZD2 C26 XL1 R52 R10 C5 C2 C51 C16 R39 R40 C27 R41 C36 R23 C42 ZD1 C30 C28 C35 7 6 5 4 3 2 1 5 R38 R36 C38 7 8 D C32 R9 8 7 6 5 4 3 2 1 CNP2 C C3 CD SERVO PWB-C CNP9 8 7 6 5 4 3 2 1 CNP5 C34 C33 C4 1 3 5 7 2 4 6 R37 B C E R33 R34 Q1 B 3 7 R51 FC5 1 TO MAIN PWB P27 11 - D CNS9 R28 R45 R29 30 25 22 C41 R30 R31 R44 R46 CNP7 CNP8 1 2 3 4 5 1 2 3 4 5 6 12 10 8 6 4 2 13 11 9 7 5 3 1 CNP6 CNP4 1 2 3 4 E 1 13 FC6 F CNS3A BL GY WH GY WH GY CNP3A M2 SLED MOTOR 1 2 3 4 5 6 6 5 4 3 2 1 6 5 4 3 2 1 CNS3B CNP7A TO DISPLAY PWB P29 10 - C SW4 PICKUP IN CD MOTOR PWB-D G M1 SPINDLE MOTOR H • The numbers 1 to 12 are waveform numbers shown in page 34. 1 2 3 4 Figure 30 WIRING SIDE OF P.W.BOARD (5/7) – 30 – 5 6 XL-HP500 CNS1B CNS1A WH GY WH GY WH GY RD 7 6 5 4 3 2 1 WB-C 7 6 5 4 3 2 1 7 8 1 GY WH GY WH GY WH GY BK 8 7 6 5 4 3 2 1 1 8 7 6 5 4 3 2 1 CD PICKUP UNIT (306) CNS2A CNS2B SWITCH PWB-E CNS7 5 YL OR RD BR BK CD SET SWB108 CD EJECT SWB105 BIM2 5 4 3 2 1 SWB107 CD IN 1 SWB106 CD TRAY CLOSE SWB101 CAM1 CNS8 1 2 3 4 5 6 BR RD OR YL GR BL SWB102 CAM2 SWB103 CAM3 BR RED OR ORANGE YL YELLOW GR GREEN BR RD OR YL OR YL RD BR BROWN RD(R) SWB104 CAM4 CNS4 1 2 3 4 COLOR TABLE BL BLUE VL VIOLET GY GRAY WH(W) WHITE BK BLACK PK PINK 1 FC6 MOB2 TRAY MOTOR MOB1 MAIN CAM MOTOR CNP7A SPLAY PWB 9 10 - C 7 8 9 10 Figure 31 WIRING SIDE OF P.W.BOARD (6/7) – 31 – 11 12 XL-HP500 F802 4A 125V A CNP801 C808 0.1 GND 2 –VCC 3 P17 7 - E CNS801 +B VCC 1 F801 4A 125V –B D802 D3SBA60F +B 4 FROM MAIN PWB (1/3) POWER PWB-B2 C809 0.1 5 D803 GD1N4004 C807 0.1 F803 2A 125V C806 0.1 F804 2A 125V 6 7 D804 D805 C805 22/50 TF D846 DS1SS133 PT801 POWER TRANSFORMER (MAIN) C844 0.0047/250 RL841 –28 Q801 KTA1274 Y R805 47 R804 47 ZD801 DZ6.2BSA R801 100K R807 10 C804 220/63 ZD803 DZ300BSB R808 –28 –33 2.2K (1/2W) C803 47/50 R806 47K R803 12K C802 47/50 C801 100/35 R802 47K D806 GD1N4004 B GD1N4004 GD1N4004 C R841 220K FW804 1 1 CNP706 D VF1 4 AC_RLAY 5 R842 1K D842 GD1N4004 D844 D843 GD1N4004 GD1N4004 WHITE AC POWER SUPPLY CORD AC 120V,60Hz C843 0.047 3 C842 470/35 P_IN P23 11 - E CNS706 FROM DISPLAY PWB D845 GD1N4004 Q841 KTC3199 GR 2 R843 47K 1 –VF C841 1000/6.3 BLACK VF2 4 FW804B FW804A 4 PT841 POWER TRANSFORMER (SUB) POWER PWB-B1 AC POWER SUPPLY CORD AC 120 V, 60 Hz E POWER PWB-B1 POWER PWB-B2 C803 R805 R804 C802 C801 ZD801 R842 R802 C843 R803 R801 R841 F803 2A 125V B C E D806 C805 Q801 C804 R807 R808 R806 ZD803 CNS706 P28 2 - F 5 4 3 2 1 CNP706 D805 TO DISPLAY PWB PT801 POWER TRANSFORMER (MAIN) BLACK F804 2A 125V R843 D844 D843 B C E Q841 D842 WHITE D803 F C807 D845 D804 C806 C841 C844 RL841 F801 4A 125V T.F. CNS801 P27 11 - G CNP801 TO MAIN PWB 1 2 3 4 5 6 7 C842 C808 C809 FW804A PT841 POWER TRANSFORMER (SUB) 4 4 1 1 D846 F802 4A 125V FW804B D802 G FW804 H • NOTES ON SCHEMATIC DIAGRAM can be found on page 12. 1 2 3 4 5 Figure 32 SCHEMATIC DIAGRAM (11/11) / WIRING SIDE OF P.W.BOARD (7/7) – 32 – 6 XL-HP500 VOLTAGE PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 VOLTAGE 1.62 V 1.02 V 1.62 V 1.88 V 3.30 V 0V 1.67 V 1.67 V 1.67 V 1.67 V 1.67 V 1.67 V 1.61 V 1.61 V 0V 0V 0V 3.30 V 0V 1.66 V 1.66 V 1.66 V 1.66 V 1.66 V 0V 3.30 V 0V 0V 0V 3.30 V 0V 0V 0V 0V 1.63 V 0V 0V 3.30 V 0V 0V 3.73 V 3.73 V 0V 0V 3.72 V 3.74 V 3.30 V 3.30 V 0V 0V 0V 3.30 V 0V 0V 0V 0V 0V 3.30 V 0V 0V 0V 0V 0V 3.28 V 4.93 V 4.91 V 0V 4.92 V 0V 3.52 V 3.52 V 2.37 V 0.96 V 2.35 V 0V 1.04 V 3.29 V 2.53 V 0V 3.28 V IC301 IC2 IC1 PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 VOLTAGE 1.68 V 1.68 V 1.87 V 2.13 V 2.13 V 2.13 V 2.13 V 0V 0V 0V 0V 0V 0V 0V 2.13 V 2.13 V 1.68 V 4.90 V 2.91 V 1.68 V 0V 0V 4.90 V 4.90 V 1.68 V 2.13 V 2.13 V 4.90 V 0V 0V 0V 0V 0V 0V 0V 4.20 V 0V 3.52 V 3.52 V 7.72 V 0.33 V 0.33 V IC101 PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 VOLTAGE 0V 0V 0.58 V 1.94 V 0V 1.32 V 0V 0.58 V 3.26 V 3.26 V 0V 0V 6.64 V 4.01 V 0V 3.28 V 0.58 V 0V 2.55 V 0V 1.96 V 0.56 V 0V 0V PIN NO. 1 2 3 4 5 6 7 8 9 VOLTAGE 0.8 V 1.5 V 3.6 V 1.5 V 0V 3.8 V 2.8 V 3.6 V 3.6 V IC302 PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 VOLTAGE 2.54 V 0V 0V 0V 0V 5.00 V 9.88 V 4.68 V 0V 0V 5.14 V 0V 5.14 V 0V 0V 2.56 V 5.16 V 0V 0V 9.89 V 0V 2.54 V IC303 PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 VOLTAGE 2.10 V 5.07 V 2.10 V 2.10 V 0V 5.15 V 0V 3.51 V 5.06 V 4.34 V 1.93 V 0V 2.26 V 1.20 V 1.20 V 2.09 V 0V 1.39 V 2.13 V 1.39 V 2.08 V 2.08 V 5.06 V 3.55 V IC601 PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 VOLTAGE 0V 0V 0V 4.95 V 0V 0V 4.93 V 0V 0V 0V 4.93 V 0V 4.93 V 4.93 V 0V 4.93 V 4.96 V 4.93 V 4.93 V 4.93 V 4.95 V 4.95 V 9.90 V 0V IC901 PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 VOLTAGE –0.13 V –0.14 V ––––– 35.1 V –33.70 V 0V 0V 35.9 V –35.9 V 0V 0V –34.8 V 0V –0.14 V –0.13 V – 33 – PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 IC701 PIN NO. 51 4.76 V 52 4.65 V 53 0V 54 0V 55 4.65 V 56 4.70 V 57 4.74 V 58 0V 59 0V 60 4.85 V 61 2.29 V 62 1.98 V 63 0V 64 4.60 V 65 0V 66 4.75 V 67 0V 68 0V 69 0V 70 0V 71 0V 72 0V 73 0V 74 5.00 V 75 0V 76 4.94 V 77 1.39 V 78 5.00 V 79 5.00 V 80 0V 81 0.32 V 82 5.00 V 83 5.00 V 84 4.78 V 85 5.00 V 86 1.94 V 87 4.94 V 88 5.00 V 89 4.90 V 90 0V 91 1.94 V 92 13.21 V 93 13.21 V 94 13.21 V 95 3.75 V 96 4.78 V 97 4.64 V 98 0V 99 0V 100 0V VOLTAGE IC851 VOLTAGE 4.94 V 0V 0V 4.94 V 0V 1.77 V 1.73 V 1.73 V 0V 0.39 V 0V 0V 4.78 V 4.78 V 4.78 V 0V 0V 0V –28.90 V –28.90 V –28.90 V –28.90 V –28.90 V –28.90 V –28.90 V –28.90 V –28.90 V –28.90 V –29.36 V –29.36 V –29.36 V –29.36 V –29.36 V –29.36 V –29.36 V –29.36 V –29.36 V –29.36 V –29.36 V –29.36 V –29.36 V –26.33 V –26.33 V –26.33 V –26.33 V –26.33 V –26.33 V –26.33 V –26.33 V –26.33 V PIN NO. 1 2 3 VOLTAGE 19.57 V 1.33 V 13.23 V IC852 PIN NO. 1 2 3 VOLTAGE 19.57 V 0V 4.95 V IC853 PIN NO. 1 2 3 VOLTAGE 19.57 V 0V 4.95 V IC854 PIN NO. 1 2 3 VOLTAGE 5.66 V 0.61 V 9.33 V IC855 PIN NO. 1 2 3 VOLTAGE 8.29 V 13.23 V 7.79 V XL-HP500 WAVEFORMS OF CD CIRCUIT Stopped CH1=500 mV DC 10:1 CH3=500 mV DC 10:1 T 1 IC1 21 Stopped CH1=200 mV DC 10:1 500 ms/div (500 ms/div) NORM:20 kS/s T 1999/04/07 09:51:15 500 ms/div (500 ms/div) NORM:20 kS/s CH2=500 mV DC 10:1 FDO T 1 FDO 1 IC1 21 2 6 IC1 22 1 TDO 2 IC1 20 3 SPDO CH1 v/DIV 500 mV =Filter= Smoothing : ON BW : FULL =Offset= CH1 : 0.000 V CH2 : 0.0 V CH3 : 0.000 V CH4 : 0.00 V Stopped CH1=500 mV DC 10:1 1 IC1 21 3 IC1 67 CH2=10 V DC 10:1 =Record Length= Main : 100 K Zoom : 2K CH3=1 V DC 10:1 =Filter= Smoothing : ON BW : FULL =Trigger= Mode : AUTO Type : EDGE CH1 Delay : 0.0 ns Hold off : 0.2 µs Stopped CH1=500 mV DC 10:1 500 ms/div (500 ms/div) NORM:20 kS/s T 2 IC1 73 CH3=1 V DC 10:1 =Trigger= Mode : NORMAL Type : EDGE CH2 Delay : 2.924 ms Hold off : 0.2 µs 1999/04/05 17:33:17 CH4=1 V 500 ms/div (500 ms/div) DC 10:1 NORM:20 kS/s 3 4 DRF PDO2 IC1 74 T TE IC1 15 =Record Length= Main : 100 K Zoom : 2K PDO1 7 FDO 1 8 4 =Offset= CH1 : 0.000 V CH2 : 0.000 V CH3 : 0.00 V CH4 : 0.00 V 3 CH Position To -3 div -1 div 0 div +1 div +3 div =Filter= =Offset= =Record Length= Smoothing : ON CH1 : 0.000 V Main : 100 K BW : FULL CH2 : 0.0 V Zoom : 2K CH3 : 0.00 V CH4 : 0.00 V 1 CH2 Position 0.20 div IC1 21 FDO 1 CH1 v/DIV 500 mV =Trigger= Mode : AUTO Type : EDGE CH1 Delay : 0.0 ns Hold off : 0.2 µs =Filter= Smoothing : ON BW : FULL Stopped CH1=2 V DC 10:1 =Offset= CH1 : 0.000 V CH2 : 0.0 V CH3 : 0.00 V CH4 : 0.00 V =Record Length= Main : 100 K Zoom : 2K T =Trigger= Mode : AUTO Type : EDGE CH2 Delay : 0.0 ns Hold off : 0.2 µs 1999/04/07 09:25:28 500 ns/div (500 ns/div) NORM:200 MS/s T 5 9 IC1 4 IC1 39 Vp-p=1.0 V~1.3 V 0.5 mV/div,0.5 µsec/div Stopped CH1=10 V DC 10:1 1 DOUT =Filter= Smoothing : ON BW : FULL T CH2=1 V DC 10:1 Stopped CH1=2 V DC 10:1 100 ms/div (100 ms/div) NORM:100 kS/s 10 =Offset= CH1 : 0.00 V CH2 : 0.00 V CH3 : 0.00 V CH4 : 0.00 V =Record Length= Main : 1K Zoom : 100 T CH2=2 V DC 10:1 CH3=2 V DC 10:1 =Trigger= Mode : NORMAL Type : EDGE CH1 Delay : 2.887 ms Hold off : 0.2 µs 1999/04/05 20:50:17 5 µs/div (5 µs/div) NORM:100 kS/s IC1 58 TE 4 IC1 15 1 2 LRSY 11 IC1 59 2 DATACK 3 IC1 67 T 1 DRF 12 IC1 60 T 3 DATA =Filter= Smoothing : ON BW : FULL =Offset= CH1 : 0.0 V CH2 : 0.00 V CH3 : 0.00 V CH4 : 0.00 V =Record Length= Main : 100 K Zoom : 2K =Filter= Smoothing : ON BW : FULL =Trigger= Mode : NORMAL Type : EDGE CH1 Delay : 2.924 ms Hold off : 0.2 µs – 34 – CH3 v/DIV 2V =Offset= CH1 : 0.00 V CH2 : 0.00 V CH3 : 0.00 V CH4 : 0.00 V =Record Length= Main : 5K Zoom : 100 =Trigger= Mode : AUTO Type : EDGE CH3 Delay : 0.0 ns Hold off : 0.2 µs XL-HP500 TROUBLESHOOTING When the CD does not function The CD section may not operate when the objective lens of the optical pickup is dirty. Clean the objective lens, and check the playback operation. When this section does not operate even after the above step is taken, check the following items. Remove the cabinet and follow the trouble shooting instructions. "Track skipping and/or no TOC (Table Of Contents) may be caused by build up of dust other foreign matter on the laser pickup lens. Before attempting any adjustment make certain that the lens is clean. If not, clean it as mentioned below." Turn the power off. Gently clean the lens with a lens cleaning tissue and a small amount of isopropyl alcohol. Do not touch the lens with the bare hand. 1. Parts code UDSKA0004AFZZ CD optical pickup Lens cleaner disc HOW TO USE 1. Using the brush in the cleaner cap, apply 1 or 2 drops of the cleaning fluid to the brush on the CD cleaner disc which has the mark next to it. 2. Place the CD cleaner disc onto the CD disc tray with the brush side down,then press the play button. 3. You will hear music for about 20 seconds and the CD player will automatically stop. If it still play continuously, press the stop button. Cleaning fluid CAUTION The CD lens cleaner should be effective for 30-50 operations, however if the brushes become worn out earlier then please replace the cleaner disc. If the CD cleaner brushes become very wet then wipe off any excess fluid with a soft cloth. Do not drink the cleaner fluid or allow it contact with the eyes. In the event of this happening then drink and / or rinse with clean water and seek medical advice. The CD cleaner disc must not be used on car CD players or on computer CD-ROM drives. All rights reserved. Unauthorized duplicating, broadcasting and renting this product is prohibited by law. Cleaner disc When a CD cannot be played 1. "E-CD01" is displayed. (1) Check the power to IC1 (LC78646E), the presence of the clock signal (16.9344 MHz) and the status of the RESET terminal (pin 66 on IC1). (2) Does the pickup move to the PICKUP-IN Switch (SW4) position ? If (1) and (2) are OK, check the system microcomputer (especially the communication line with the DSP). 2. Pressing the CD operation key is accepted, but playback does not occur. (1) Focus-HF system check (2) Tracking system check (3) Spin system check (4) PLL system check (5) Others – 35 – XL-HP500 Stopped CH1=500 mV DC 10:1 (1) Focus-HF system check. Although a CD is inserted and the cover is closed, "NO DISC" is displayed. CH3=500 mV DC 10:1 T 500 ms/div (500 ms/div) NORM:20 kS/s FDO 1 Press the Tray1 CD Eject Button (SW723) without inserting a disc, and try starting the playback operation. TDO 3 CH1 v/DIV 500 mV =Filter= Smoothing : ON BW : FULL =Offset= CH1 : 0.000 V CH2 : 0.0 V CH3 : 0.000 V CH4 : 0.00 V =Record Length= Main : 100 K Zoom : 2K =Trigger= Mode : AUTO Type : EDGE CH1 Delay : 0.0 ns Hold off : 0.2 µs Figure 36-1 1. Does the pickup move to the PICKUP-IN Switch (SW4) position ? No Sled motor (M2). Yes No 2. Does the focus (lens) move up and down ? (Waveform drawing Figure 36-1) Check the focus peripheral circuit. Yes No 3. Is the laser lit ? Check the laser diode driver Q1 peripheral circuit. Yes No 4. Is the turntable rotating ? Spindle motor (M1). When a disc is loaded, start playback operation. No 1. Is focus servo activated ? (Waveform drawing Figure 36-2) Pins 7~11, 79 and 80 on IC1 Check the laser diode driver Q1 peripheral circuit. Yes No 2. Does DRF change from "L" to "H" ? Is the disc rotating ? No 3. Is the HF waveform normal ? (Waveform drawing Figure 36-3) CH2=10 V DC 10:1 CH3=1 V DC 10:1 Check the spin system. If the disc is spinning and a HF waveform is generated, DRF will go H. Yes Stopped CH1=500 mV DC 10:1 No If the level is not normal. 500 ms/div (500 ms/div) NORM:20 kS/s FDO 1 T 2 DRF TE 3 CH Position To -3 div -1 div 0 div +1 div +3 div =Filter= =Offset= =Record Length= Smoothing : ON CH1 : 0.000 V Main : 100 K BW : FULL CH2 : 0.0 V Zoom : 2K CH3 : 0.00 V CH4 : 0.00 V CH2 Position 0.20 div Vp-p=1.0 V~1.3 V 0.5 mV/div,0.5 µsec/div =Trigger= Mode : AUTO Type : EDGE CH1 Delay : 0.0 ns Hold off : 0.2 µs Figure 36-3 Figure 36-2 – 36 – XL-HP500 (2) Tracking system check. Check the TE waveform at pin 15 on IC1. If the waveform shown in Figure 37-1 appears and soon after NO DISC appears ? Yes The tracking servo is not activated. Check the peripheral circuits at pins 14, 15 and 20 on IC1, and CNS1A/B. Yes A normal jump operation cannot be completed or the beginning of the track cannot be found. Check the around pin 20 on IC1. No "Initialization" is possible, but play is not possible ? No Data cannot be read. Check the VCO-PLL (Pin73~78 on IC1) system. "Initialization" is not possible. Stopped CH1=10 V DC 10:1 T CH2=1 V DC 10:1 100 ms/div (100 ms/div) NORM:100 kS/s TE 2 T 1 DRF =Filter= Smoothing : ON BW : FULL =Offset= CH1 : 0.0 V CH2 : 0.00 V CH3 : 0.00 V CH4 : 0.00 V =Record Length= Main : 100 K Zoom : 2K =Trigger= Mode : NORMAL Type : EDGE CH1 Delay : 2.924 ms Hold off : 0.2 µs Figure 37-1 (3) Spin system check. Press the OPEN/CLOSE switch without inserting a disc, and then try starting the play operation. 1. The turntable rotates a little ? (Waveform drawing Figure 37-2) The spin driver circuit is OK. Yes No 2. The turntable doesn't rotate. Check around pin 22 on IC1, pins 26 and 27 on IC2, and CNS3A/B. Stopped CH1=200 mV DC 10:1 T 1999/04/07 09:51:15 500 ms/div (500 ms/div) NORM:20 kS/s CH2=500 mV DC 10:1 T FDO 2 1 SPDO =Filter= Smoothing : ON BW : FULL =Offset= CH1 : 0.000 V CH2 : 0.000 V CH3 : 0.00 V CH4 : 0.00 V =Record Length= Main : 100 K Zoom : 2K Figure 37-2 – 37 – =Trigger= Mode : NORMAL Type : EDGE CH2 Delay : 2.924 ms Hold off : 0.2 µs XL-HP500 (4) PLL system check. Stopped CH1=500 mV DC 10:1 When a disc is loaded, start play operation. CH3=1 V DC 10:1 1999/04/05 17:33:17 CH4=1 V 500 ms/div (500 ms/div) DC 10:1 NORM:20 kS/s PDO1 3 4 The HF waveform is normal, but the TOC data cannot be read. PDO2 T FDO 1 Check the PDO waveform. (Figure 38-1) CH1 v/DIV 500 mV =Filter= Smoothing : ON BW : FULL =Offset= CH1 : 0.000 V CH2 : 0.0 V CH3 : 0.00 V CH4 : 0.00 V =Record Length= Main : 100 K Zoom : 2K =Trigger= Mode : AUTO Type : EDGE CH2 Delay : 0.0 ns Hold off : 0.2 µs Check around pins 73~78 on IC1. Figure 38-1 (5) Others. The HF waveform is normal and the time is displayed normally, but no sound is produced. Or the sound has dropouts. No Is pin 52 (C2F) on IC1 "L" ? There are too many error flags on a damaged disc which makes error correction impossible. Yes 1. When playing at normal speed. Check the peripheral circuit at pin 39 (DOUT) on IC1 and the waveform (Figure 38-2). Check again using a known good disc. Stopped CH1=2 V DC 10:1 If OK, Check the unit. T 1999/04/07 09:25:28 500 ns/div (500 ns/div) NORM:200 MS/s T 1 DOUT =Filter= Smoothing : ON BW : FULL =Offset= CH1 : 0.00 V CH2 : 0.00 V CH3 : 0.00 V CH4 : 0.00 V =Record Length= Main : 1K Zoom : 100 Figure 38-2 – 38 – =Trigger= Mode : NORMAL Type : EDGE CH1 Delay : 2.887 ms Hold off : 0.2 µs XL-HP500 FUNCTION TABLE OF IC IC1 VHiLC78646E-1: CD Servo (LC78646E) (1/2) Pin No. Terminal Name Input/Output Setting in Reset 1 SLCO 2 Function Output — Control output. SLCIST Input — 3 EFMIN Input — 4 RF Output — 5 RFVDD Input — RF power terminal. 6 RFVSS — — RF earth terminal. To be connected to 0 V. 7 FIN1 Input — A+C signal input terminal. 8 FIN2 Input — B+D signal input terminal. 9 TIN1 Input — E signal input terminal. 10 TIN2 Input — F signal input terminal. 11 VREF Output RFVDD/2 12 REF1 Input — 13* FE Output ZHI 14 TEC Output — 15* TE Output ZHI 16* RFMON Output ZHI 17 JITTC — — Capacitor connection terminal for jitter detection. 18 ADAVDD Input — Power terminal for servo A/D, D/A. 19 ADAVSS — — Earth terminal for serve A/D, D/A. To be connected to 0 V. 20 TDO Output ADAVDD/2 Output terminal for tracking control. D/A output. 21 FDO Output ADAVDD/2 Output terminal for focus control. D/A output. 22 SPDO Output ADAVDD/2 Output terminal for spindle control. D/A output. 23 SLDO Output ADAVDD/2 Output terminal for sled control. D/A output. 24* GPDAC Output ADAVDD/2 25* CONT4 Input/Output Input Mode 26 CONT5 Input/Output Input Mode 27* SBCK/CONT6 Input/Output Input Mode Servo D/A general-purpose output terminal. Controlled by commands from the microcomputer. When not used, set General-purpose I/O terminal 5. them as input terminals and connect General-purpose I/O terminal 6 or to 0 V, or set them as output Subcode reading clock input terminal. terminals and leave open. 28 SBCK/FG Input — Subcode reading clock input terminal/FG signal input terminal/external emphasis setting terminal. Terminal functions are set by commands. When not used, connect to 0 V. 29* DEFECT Output L Defect terminal. 30* V/*P Output H Auto switching monitor output terminal for rough servo phase control. “H”: rough servo, “L”: phase servo. 31* FSEQ Output L Sync signal detection output terminal. The status changes to “H” when the sync signal detected in EFM and the sync signal of internal generation are identified. 32* MONI1 Output L Internal signal monitor terminal 1. 33* MONI2 Output L Internal signal monitor terminal 2. 34* MONI3 Output L Internal signal monitor terminal 3. 35* MONI4 Output L Internal signal monitor terminal 4. 36* MONI5 Output L Internal signal monitor terminal 5. 37 VSS — — Digital system earth terminal. To be connected to 0 V. 38 VDD Input — Digital system power terminal. 39* DOUT Output L Digital OUT output terminal. (EIAJ format) 40 TEST Input L Input terminal for test. To be connected to 0 V. 41 LVDD Input — 42 LCHO Output LVDD/2 43 LVSS — — For slice level control. Resistor connection terminal for SLCO output current setting. RF signal input terminal. RF signal monitor terminal. VREF voltage output terminal. Reference supply setting terminal. FE signal monitor terminal. LPF capacitor connection terminal for TE signal. TE signal monitor terminal. RF internal signal monitor terminal. General-purpose I/O terminal 4. Power supply for Left channel. Left channel D/A converter Left channel output. GND for Left channel. Must be connected to 0 V. In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. – 39 – XL-HP500 IC1 VHiLC78646E-1: CD Servo (LC78646E) (2/2) Pin No. Terminal Name Input/Output Setting in Reset 44 RVSS — — 45 RCHO Output LVDD /2 46 RVDD Input — 47 XVDD Input — 48 XOUT 49 XIN 50 FSX/16MIN 51 XVSS 52* Function Right channel D/A converter GND for Right channel. Must be connected to 0 V. Right channel output. Power supply for Right channel. Power supply for crystal oscillator. Crystal Oscillator Output Oscillator Input Oscillator Connected for the 33.8688 MHz crystal oscillator ciement. Input/Output Input — — C2F Output H C2 FLAG monitor port. 53* EFLG Output L C1, C2 error corrected monitor port. 54* 16MOUT Output Clock 55 ASLRCK Input — 56 ASDACK Input — 57 ASDFIN Input — 58* LRCK Output L 59* BCK Output L 60* DATA Output L 61 CE Input — 62 CL Input — Microcomputer 63 DI Input — Interface 64 DO Output (H) 65 *WRQ Output H Interruption signal output. 66 *RES Input — Chip reset signal input port. This port must be set LOW after first applied power on. 67 DRF Output L Focus detection output port. 68 VDD5 Input — Power supply for Microprocessor. 69 VSS — — GND for digital circuit. Must be connected to 0 V. 70* CONT3 Input/Output Input 71* CONT2 Input/Output Input 72* CONT1 Input/Output Input 73 PDO1 Output — Internal VCO control phase comparator output port 1. 74 PDO2 Output Input Internal VCO control phase comparator output port 2. 75 VVSS — — 76 PCKIST Input — 77 VVDD Input — Power supply for internal VCO. 78 FR Input — VCO frequency range adjustment port. 79 LDS Input — LASER power detected signal input port. 80 LDD Output — LASER power control signal output port. 7.35 kHz Synchronization signal monitor port. or Clock input port for Digital filter & D/A Crystal Oscillator GND for crystal oscillator. Must be connected to 0 V. 16.9344 MHz output port. Left/Right clock input port. (If this port does not use, must be connect to 0 V.) Anti-shock Bit clock input port. (If this port does not use, must be connect to 0 V.) Left/Right channel data input port. (If this port does not use, must be connect to 0 V.) Left/Right clock output port. Digital data Bit clock output port. Left/Right channel data output port. Chip enable signal input port. Data transfer clock input port. Data input port. Data output port. (N-ch. open drain output.) General purpose port 3. Controlled with serial data command from microcomputer. When not used, General purpose input/ General purpose port 2. output terminal. Set it as the input terminal and open it by connecting to 0 V, or set it as the output terminal General purpose port 1. and open it. PLL GND for internal VCO. Must be connected to 0 V. PDO output current adjustment resistor connection port. In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. Be sure to supply the same potential to each power terminal. (VVDD, ADAVDD, VDD, LVDD, RVDD, XVDD) Terminal witch is controlled by the power terminal (VDD5 V) for a microcomputer interface : CE (61 pin), CL (62 pin), DI (63 pin), DO (64 pin), WRQ (65 pin), RES (66 pin), DRF (67 pin) – 40 – XL-HP500 LDD LDS FR VVDD PCKIST VVSS PD02 PD01 CONT1 CONT2 CONT3 VSS VDD5 DRF *RES *WRQ DO DI CL CE IC1 VHiLC78646E-1: CD Servo (LC78646E) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 SLCO 1 60 DATA SLCIST 2 59 DATACK EFMIN 3 58 LRSY RF 4 57 ASDFIN RFVDD 5 56 ASDACK RFVSS 6 55 ASLRCK FIN1 7 54 16MOUT FIN2 8 53 EFLG TIN1 9 52 C2F TIN2 10 51 XVSS LC78646E VREF 11 50 FSX/16MIN REF1 12 49 XIN 31 32 33 34 35 36 37 FIN1 MONI4 (3.3V)VSS – + MIX EQ 40 RF TEC 38 39 TEST 29 30 VDD 28 DOUT 26 27 MONI5 25 MONI2 24 TE 23 V/*P 22 FE FDO 21 MONI3 41 LVDD MONI1 42 LCHO TDO 20 FSEQ 43 LVSS ADAVSS 19 DEFECT 44 RVSS ADAVDD 18 SBCK/FG 45 RCHO JITTC 17 SBCK/CONT6 RFMON 16 CONT5 46 RVDD CONT4 47 XVDD TE 15 GPDAC TEC 14 SLDO 48 XOUT SPDO FE 13 RFVDD RFVSS PH AGC + FIN2 – + – TIN1 + – TBAL TIN2 – + LPF + BH LPF SW + – LPF + – + – – TBAL LEVEL SET MNI CONT – + REF1 RFMON RAM VREF DEFECT TRACK JUMP ADIN ADAVDD ADAVSS SERVO PROCESSOR A/D LDS AUTO ADJUST JITTER DETECT JITTC SLCO EFMIN SLCIST SW DRF DRF VDD5V RUPTURE DEFECT PLL VCEC FRAME SYNC DETECT,PROTECT INSERT, EFM DECODE CLV,CAV CONTROL SBCK/FG XIN XOUT 16MOUT XVDD XVSS *RES *WRQ CL CE DI DO VDD5V CONT1, 2, 3 CONT4, 5, SBCK/CONT6 FD0 TD0 SLD0 SPD0 GPDAC D/A S/H SLICE LEVEL CONTROL PCK PDO1 PDO2 FR PCKIST VVDD VVSS LDD APC V/*P SUBCODE DECODE CRC CLOCK GENERATOR COMMAND INTERFACE MONITOR SIGNAL SELECTOR ERROR CORRECTION AUDIO CD C1-2,C2-2 VDD VSS MONI1~5 RAM FSX/16MIN C2F EFLG AUDIO OUT GENERAL-PURPOSE PORTS FSEQ DOUT 8FS DIGITAL FILTER INTERPOLATION MUTE ATTENUATION DEEMPHSIS SERIAL OUT LRSY DATACK DATA 1bit DAC LPF EXTERNAL AUDIO IN ASLRCK ASDACK ASDFIN RVDD RVSS RCHO LCHO LVDD LVSS TEST Figure 41 BLOCK DIAGRAM OF IC – 41 – XL-HP500 IC2 VHIM63001FP-1: Focus/Tracking/Spin/Sled Driver (M63001FP) Pin No. 1 Terminal Name Terminal Name Pin No. Function IN2– CH2 inverted input 22 IN5– Function CH5 inverted input 2 IN1A– CH1 inverted input 23 IN5+ CH5 non-inverted output 3* IN1B– CH1 output offset control 24 VCC2 Power supply 2 (CH4) 4 OUT1– CH1 inverted output 25 IN4– CH4 inverted input 5 OUT1+ CH1 non-inverted output 26 OUT4– CH4 inverted output 6 OUT2– CH2 inverted output 27 OUT4+ CH4 non-inverted output 7 OUT2+ CH2 non-inverted output 28 VCC3 Power supply 3 (CH5) 8-14 GND GND 29-35 GND GND 15 OUT3+ CH3 non-inverted output 36 OUT5+ CH5 non-inverted output 16 OUT3– CH3 inverted output 37 OUT5– CH5 inverted output 17 IN3– CH3 inverted input 38 OUT6+ CH6 non-inverted output 18 VCC1 Power supply 1 (CH1,CH2,CH3) 39 OUT6– CH6 inverted output 19 STANDBY STANDBY signal input 40 VCC4 Power supply 4 (CH6) 20 VREF CH1-CH4 Reference voltage input 41 IN6– CH6 inverted input 21 MUTE MUTE SIGNAL INPUT (CH6) 42 IN6+ CH6 non-inverted input 23 IN5+ 22 IN5– MUTE 21 24 VCC2 VREF 20 26 OUT4– 25 IN4– 27 OUT4+ IN3– 17 28 VCC3 OUT3– 16 STANDBY 19 VCC1 18 OUT3+ 15 GND 11 MP63001FP 29 33 10 30 34 9 14 35 8 31 36 OUT5+ 7 OUT2+ 13 37 OUT5– 6 OUT2– 12 38 OUT6+ 5 OUT1+ 32 39 OUT6– 4 OUT1– 40 VCC4 3 IN1B– 41 IN6– 2 42 IN6+ 1 IN2– IN1A– GND In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. VCC1 VCC4 VREFMAMP 10K H:DISABLE VCC1 VCC1 – + 10K 10K 5K VCC1 – + 10K 5K IoMAX 300mA OUT2+ 5K 10K 10K 5K 5K OUT5+ 12.5K 5K VCC3 – + 13.3K 10K 5K 10K OUT3+ 13.3K VCC2 5K VCC1 – + 5K IoMAX 300mA VCC2 – + VCC1 13.3K TSD VREF SLIDE 10K 5K Figure 42 BLOCK DIAGRAM OF IC – 42 – OUT4+ 13.3K VCC2 – + GND GND OUT3– IoMAX 300mA LOADING OUT5– IN4– VCC1 – + VCC3 VCC3 VREFMAMP IN5+ VREFM1 IoMAX 300mA CHANGER OUT6– VCC3 – + 10K IoMAX 300mA OUT2– 12.5K IN5– STANDBY CH1~6 TRACKING IN3– VREF 5K VCC4 – + 10K 13.3K OUT6+ 12.5K 10K LOW.OPEN:DISABLE VCC1 STANDBY VCC1 – + 10K 10K VCC4 VREFMAMP IN6+ OUT1– 13.3K VCC1 – + MUTE CH6 FOCUS IN2– 10K VCC4 – + MUTE OUT1+ 13.3K 12.5K IN6– VREFM3 13.3K + – 10K IN1A– + – IN1B– VREFM4 VCC1 – + 5K IoMAX 500mA SPM OUT4– XL-HP500 IC601 VHiLC75341/-1: Audio Processor (LC75341) Terminal Name Pin No. Terminal Name Pin No. Function Function 1 DI Serial data and clock input pin for control. 13-16 R1-4 Input signal pin. 17 RSEL0 Input selector output pin. 2 CE Chip enable pin. Data written into an internal latch in a timing of "H" to "L". Each analog switch is activated. Data transfer enabled at "H" level. 18 RIN Volume + equaliser output pin 19 RTRE Treble band filter comprising capacitor and resistor connection pin. 3 VSS Ground pin. 20 RBASS 4 LOUT Bass band filter comprising capacitor and resistor connection pin and bass/treble output pin. Bass band filter comprisingcapacitor and resistor connection pin. 21 ROUT 5 LBASS Bass band filter comprisingcapacitor and resistor connection pin. Bass band filter comprising capacitor and resistor connection pin and bass/treble output pin. 22 VREF 6 LTRE Treble band filter comprising capacitor and resistor connection pin. 7 LIN Volume + equaliser output pin 0.5x VDD voltage generation block for analog ground. Capacitor of several 10µF to be connected between VREF and AWSS (VSS) as a countermeasure against power ripple. 8 LSEL0 Input selector output pin. 23 VDD Supply pin 9-12 L4-1 Input signal pin. 24 CLK Serial data and clock input pin for control. LSEL0 LIN LTRE LBASS LOUT IC601 VHiLC75341/-1: Audio Processor (LC75341) 8 7 6 5 4 L4 9 CD L3 10 L2 11 L1 12 Tuner Tape CONTROL CIRCUIT Video CONTROL CIRCUIT R1 13 LVref 2 CE CCB INTERFACE 1 DI 24 CLK CONTROL CIRCUIT R2 14 3 VSS RVref RSEL0 17 18 19 20 21 ROUT 22 VREF RBASS R4 16 RTRE 23 VDD RIN R3 15 Figure 43 BLOCK DIAGRAM OF IC – 43 – XL-HP500 IC701 RH-iX0574AWZZ: System Microcomputer (IX0574AW) (To Serial No.211XXXXX) (1/2) IC701 RH-iX0578AWZZ: System Microcomputer (IX0578AW) (From Serial No.212XXXXX) (1/2) Pin No. Port Name Terminal Name Input/Output Function 1 VDD VDD 2 P37 -20dBATT Input (+) Power supply. Output -20dB Attenuator. 3* P36 NO USE Output Open 4 P35 T-BIAS Output Tape record bias. 5 P34 SP_RELAY Output Speaker relay control. 6 P33 T-REC/PLAY Output Tape REC/PLAY change. 7 P32 CD RESOUT Output CD DSP reset. 8 P31 AC_RELAY Output AC relay control. 9 P30 NO USE Input Connect to GND. 10 RESET RESET Input Reset. 11 X2 X2 Output Main clock. 12 X1 X1 Input Main clock. 13 VPP/IC VPP/IC — GND 14* XT2 XT2 — Open 15 P04 CD_DRF 16 VDD VDD 17 P27 CD CLK Output CD DSP clock. 18 P26 CD DI Output CD DSP command. 19 P25 CD DO Input 20 P24 CD CE Output CD DSP CE output. 21 P23 CE Output CE output. 22 P22 CLK Output Clock output. 23 P21 DI Output Data output. 24 P20 DO Input Input Input — CD DRF level detection. (+) Power supply. CD DSP CODE Q out. Data input. 25 AVSS AVSS 26 P17 NO USE Input Connect to GND. Analog ground. 27 ANI6 NO USE Input Connect to GND. 28 ANI5 FPA/FPB SW Input Tape F.P A/B SW & PLAY 2 SW. 29 ANI4 PROTECT Input Power abnormal detect. 30 ANI3 NO USE Input Connect to GND. 31-33 ANI2-ANI0 KEY 2-KEY 0 Input Key input. 34 AVDD AVDD Input Analog VDD. 35 AVREF AVREF 36 INTP3 P_IN 37 P02 CD_WRQ Input CD write read request. 38 INTP1 SP DET Input Speaker abnormal detect. 39 INTP0 REMOCON Input Remocon input. 40 VSS VSS — Ground voltage. 41 P74 SMUTE Output 42 P73 T1-RUN Input 43 P72 T_SOL_A Output Tape solenoid control. 44 P71 T_MOTOR Output Tape motor control. 45 P70 TIMER LED Output Timer LED control. 46 VDD VDD Input (+) Power supply. 47 P127 JOG 1 Input Volume jog input 1. 48 P126 JOG 2 Input Volume jog input 2. 49 P125 NO USE Input Connect to GND. 50* P124 NO USE Output 51* P123 NO USE Output Open 52 P122 NO USE Output Open 53 P121 NO USE Input Open — Analog ref voltage. Input Power failure detect. System mute control. TAPE 1 RUN PULSE input. Open In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. – 44 – XL-HP500 IC701 RH-iX0574AWZZ: System Microcomputer (IX0574AW) (To Serial No.211XXXXX) (2/2) IC701 RH-iX0578AWZZ: System Microcomputer (IX0578AW) (From Serial No.212XXXXX) (2/2) Pin No. Port Name Terminal Name Input/Output Function 54 P120 NO USE Output Open 55 P117 NO USE Input Open 56 P116 CAM 1 SW Input EH mecha CAM 1 SW detection. 57 P115 CAM 2 SW Input EH mecha CAM 2 SW detection. 58 P114 CAM 3 SW Input EH mecha CAM 3 SW detection. 59 P113 CAM 4 SW Input EH mecha CAM 4 SW detection. 60 P112 TRAY EJT SW Input EH mecha tray eject SW detection. 61 P111 TRAY CLS SW Input EH mecha tray close SW detection. 62 P110 TRAY IN SW Input EH mecha tray stock in SW detection. 63 P107 TRAY SET SW Input EH mecha tray set SW detection. 64 P106 C MOTOR– 65 P105 C MOTOR+ Output EH mecha CAM motor control. 66 P104 T MOTOR– Output EH mecha tray motor control. 67 P103 T MOTOR+ Output EH mecha tray motor control. 68 P102 T MOTOR H-L Output EH mecha tray speed control. Output EH mecha CAM motor control. 69* P101/FIP30 NO USE Output 70 P100/FIP29 DIST IN Input Open 71* P97 NO USE Output Open 72 P96/FIP27 DIST0/S18 Output Destination output./FL segment driver. 73 P95/FIP26 DIST1/S17 Output Destination output./FL segment driver. 74-78 FIP25-FIP21 S16-S12 Output FL segment driver. 79 VLOAD VLOAD Input 80-90 FIP20-FIP10 S11-S1 Output FL segment driver. 91-100 FIP9-FIP0 G10-G1 Output FL grid driver. Destination input. FL driver power supp. -30 V In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside. – 45 – XL-HP500 FL DISPLAY FL701 VVKNA10SS23-1 GRID ASSIGNMENT 1G 2G 3G 4G 5G 6G 8G 7G 9G 10G 1a 2a 3a a a h j k f col b g b m e Dp (1G) c p r c n d small dot (2G~9G) ANODE CONNECTION 1G P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 1 2G 3G MP3 ( ) 2 2b 2c 3 3a 3b 3c 5G 6G RDS TA TP 8G 9G PTY 7G PTYI ST a b k j h f m d g p e n r c a b k j h a b k j h a b k j h a b k j h a b k j h a b k j h col Dp small dot a b k j h f m d g p e n r c f m d g p e n r c f m d g p e n r c f m d g p e n r c f m d g p e n r c f m d g p e n r c f m d g p e n r c 1a 1b 1c 2a 4G – 46 – 10G (white) (Rsh.o) SLEEP X-BASS MEMORY MHz kHz REC XL-HP500 PARTS GUIDE MICRO COMPONENT SYSTEM MODEL XL-HP500 XL-HP500 Micro Component System consisting of XL-HP500 (main unit) and CP-HP500 (speaker system). “HOW TO ORDER REPLACEMENT PARTS” To have your order filled promptly and correctly, please furnish the following information. 1. MODEL NUMBER 2. REF. No. 3. PART NO. 4. DESCRIPTION For U.S.A. only Contact your nearest SHARP Parts Distributor to order. For location of SHARP Parts Distributor, Please call Toll-Free; 1-800-BE-SHARP MARK: SPARE PARTS-DELIVERY SECTION Explanation of capacitors/resistors parts codes Capacitors Resistors VCC ....................... Ceramic type VCK ........................ Ceramic type VCT ........................ Semiconductor type VC • • MF ............... Cylindrical type (without lead wire) VC • • MN ............... Cylindrical type (without lead wire) VC • • TV ................ Square type (without lead wire) VC • • TQ ............... Square type (without lead wire) VC • • CY ............... Square type (without lead wire) VC • • CZ ............... Square type (without lead wire) VC • • • • • • • • • J .. The 13th character represents capacity difference. ("J" ±5%, "K" ±10%, "M" ±20%, "N" ±30%, "C" ±0.25 pF, "D" ±0.5 pF, "Z" +80-20%.) VRD ....................... Carbon-film type VRS ........................ Carbon-film type VRN ....................... Metal-film type VR • • MF ............... Cylindrical type (without lead wire) VR • • MN ............... Cylindrical type (without lead wire) VR • • TV ................ Square type (without lead wire) VR • • TQ ............... Square type (without lead wire) VR • • CY ............... Square type (without lead wire) VR • • CZ ............... Square type (without lead wire) VR • • • • • • • • • J .. The 13th character represents error. ("J" ±5%, "F" ±1%, "D" ±0.5%.) If there are no indications for the electrolytic capacitors, error is ±20%. If there are no indications for other parts, the resistors are ±5% carbon-film type. CAUTION:FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH SAME TYPE F801,802 4A, 125V/ F803,804 2A, 125V FUSES. ATTENTION:POUR ASSURER UNE LONGUE PROTECTION CONTRE UN INCENDIE, REMPLACER SEULEMENT PAR UN FUSIBLE DE TYPE F801,802 4A, 125V/ F803,804 2A, 125V FUSES. NOTE: Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace parts with specified ones for maintaining the safety and performance of the set. XL-HP500 NO. PRICE RANK PART CODE DESCRIPTION INTEGRATED CIRCUITS IC1 IC2 VHILC78646E-1 VHIM63001FP-1 J J IC701 RH-IX0574AWZZ J IC701 RH-IX0578AWZZ J IC701 RH-IX0578AWZZ J IC851 VHIKIA7812AP1 J IC852 VHIKIA7810AP1 J IC853 VHIKIA7805AP1 J IC854 VHIAN78L05/-1 J IC901 VHISTK40271-1 J AY CD Servo,LC78646E AX Focus/Tracking/Spin/Sled Driver, M63001FP AM Playback and Record/Playback Amp.,AN7345K AG FM Front End,TA7358AP AP PLL (Tuner),LC72131 AN FM IF Det./FM Mpx./AM IF, LA1832S AM Audio Processor,LC75341 AX System Microcomputer, IX0574AW (To Serial No.21100500) [For Canada] AX System Microcomputer, IX0574AW (To Serial No.21104113) [Except for Canada] AX System Microcomputer, IX0578AW (From Serial No.21200501) [For Canada] AX System Microcomputer, IX0578AW (From Serial No.21204118) [Except for Canada] AF Constant Voltage Regulator, KIA7812AP AF Constant Voltage Regulator, KIA7810AP AF Constant Voltage Regulator, KIA7805AP AE Constant Voltage Regulator, AN78L05 AZ Power Amp.,STK402-071 IC101 VHIAN7345K/-1 J IC301 IC302 IC303 VHITA7358AP-1 VHILC72131/-1 VHILA1832S/-1 J J J IC601 IC701 VHILC75341/-1 RH-IX0574AWZZ J J VSKTC2026//-1 VSKTA1266GR-1 VSKTC3203Y/-1 VS2SC1845F/-1 VSKTC3199GR-1 VSKTA1266GR-1 VSKRC104M//-1 VSKTC3203Y/-1 VSKTA1266GR-1 VSKRC104M//-1 VSKTC3194Y/-1 VSKTA1266GR-1 VSKTA1273Y/-1 VSKTA1271Y/-1 VSKTC3199GR-1 VSKTC3199GR-1 VSKRC102M//-1 VSKTA1274Y/-1 VSKTC3199GR-1 VSKTC3199GR-1 VSKTC3203Y/-1 J J J J J J J J J J J J J J J J J J J J J AF AB AC AC AB AB AC AC AB AC AD AB AE AC AB AB AC AE AB AB AC Silicon,NPN,KTC2026 Silicon,PNP,KTA1266 GR Silicon,NPN,KTC3203 Y Silicon,NPN,2SC1845 F Silicon,NPN,KTC3199 GR Silicon,PNP,KTA1266 GR Digital,NPN,KRC104 M Silicon,NPN,KTC3203 Y Silicon,PNP,KTA1266 GR Digital,NPN,KRC104 M Silicon,NPN,KTC3194 Y Silicon,PNP,KTA1266 GR Silicon,PNP,KTA1273 Y Silicon,PNP,KTA1271 Y Silicon,NPN,KTC3199 GR Silicon,NPN,KTC3199 GR Digital,NPN,KRC102 M Silicon,PNP,KTA1274 Y Silicon,NPN,KTC3199 GR Silicon,NPN,KTC3199 GR Silicon,NPN,KTC3203 Y VHDDS1SS133-1 VHDDS1SS133-1 VHDDS1SS133-1 VHDDS1SS133-1 VHDDS1SS133-1 VHDD3SBA60F-1 VHDGD1N4004-1 VHDGD1N4004-1 VHDDS1SS133-1 VHDDS1SS133-1 VHDDS1SS133-1 VHDGD1N4004-1 VHDDS1SS133-1 VHDDS1SS133-1 VHPSLR342VCJ1 VHCSVC348S/-1 VHCSVC211C/-1 J J J J J J J J J J J J J J J J J AB AB AB AB AB AG AB AB AB AB AB AB AB AB AC AK AG Silicon,DS1SS133 Silicon,DS1SS133 Silicon,DS1SS133 Silicon,DS1SS133 Silicon,DS1SS133 Silicon,D3SBA60F Silicon,GD1N4004 Silicon,GD1N4004 Silicon,DS1SS133 Silicon,DS1SS133 Silicon,DS1SS133 Silicon,GD1N4004 Silicon,DS1SS133 Silicon,DS1SS133 LED,Red,SLR342VC Variable Capacitance,SVC348S Silicon,SVC211C,Variable Cap TRANSISTORS IC855 Q1 Q2 Q101~104 Q105~108 Q109 Q110 Q111 Q112 Q113,114 Q302 Q360,361 Q500 Q501 Q601~604 Q701 Q702 Q801 Q841 Q901~905 Q906 DIODES D301~305 D500 D701 D703 D705~709 D802 D803~806 D842~845 D846 D851~853 D855~859 D860 D905~907 D911,912 LED701 VD301 VD302,303 NO. ZD1 ZD2 ZD351 ZD801 ZD803 ZD852 PRICE RANK PARTS CODE DESCRIPTION VHEDZ3R3BSB-1 VHEDZ3R9BSB-1 VHEDZ5R1BSB-1 VHEDZ6R2BSA-1 VHEDZ300BSB-1 VHEDZ9R1BSB-1 J J J J J J AB AC AC AB AB AB Zener,3.3V,DZ3.3BSB Zener,3.9V,DZ3.9BSB Zener,5.1V,DZ5.1BSB Zener,6.2V,DZ6.2BSA Zener,30V,DZ300BSB Zener,9.1V,DZ9.1BSB RFILR0008AWZZ RFILF0124AFZZ RFILF0003AWZZ RFILA0009AWZZ J J J J AE AD AK AE Band Pass Filter FM IF FM IF AM IF RTRNP0452AWZZ RTRNP0483AWZZ RCILB0065AWZZ RCILI0017AWZZ RCILA0052AWZZ RCILB0067AWZZ RCILI0019AWZZ J J J J J J J BC AL AC AB AE AD AD Power (Main) Power (Sub) OSC,FM FM IF AM Antenna AM OSC AM IF VP-XHR82K0000 VP-MK331K0000 RCILR0056AWZZ VP-DH101K0000 VP-DH101K0000 J J J J J AC AB AB AB AB 0.82 µH 330 µH,Choke FM RF 100 µH,Choke 100 µH,Choke J J J J AF AF AE AH Crystal,456 kHz Crystal,4.5 MHz Ceramic,16.9344 MHz Crystal,4.19403 MHz J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AB AA AB AA AB AB AA AB AB AB AA AA AB AC AB AD AA AB AB AA AA AA AA AA AA AB AB AB AA AB AC AB AA AB AA AA AA AB AA 47 µF,25V,Electrolytic 0.01 µF,16V 47 µF,25V,Electrolytic 0.001 µF,50V 0.047 µF,50V,Mylar 0.1 µF,16V 0.0027 µF,16V 100 µF,10V,Electrolytic 10 µF,50V,Electrolytic 0.22 µF,50V,Electrolytic 100 pF,50V 0.022 µF,25V 100 µF,10V,Electrolytic 330 µF,6.3V,Electrolytic 100 µF,10V,Electrolytic 3.3 µF,16V,Electrolytic 0.01 µF,16V 10 µF,50V,Electrolytic 0.0015 µF,50V,Mylar 0.022 µF,25V 100 pF,50V 100 pF,50V 100 pF,50V 0.022 µF,25V 100 pF,50V 0.047 µF,50V,Mylar 0.22 µF,50V,Electrolytic 0.1 µF,16V 0.01 µF,16V 100 µF,10V,Electrolytic 220 µF,6.3V,Electrolytic 100 µF,10V,Electrolytic 0.01 µF,16V 100 µF,10V,Electrolytic 0.001 µF,50V 0.022 µF,25V 22 pF (CH),50V 0.022 µF,50V 0.001 µF,50V FILTERS BF301 CF302 CF351 CF352 TRANSFORMERS 1 PT801 1 PT841 T301 T302 T303 T306 T351 COILS L1 L103 L312 L351,352 L701 VIBRATORS X351 X352 XL1 XL700 92LCRSTL1425A RCRSP0019AWZZ RCRM-0047AWZZ RCRSP0003AWZZ CAPACITORS C1 C2 C3 C4 C5 C6 C8 C9 C10 C11 C12 C13 C14 C16 C18 C19 C22 C23,24 C25,26 C27 C28 C30 C32 C33 C34 C35 C36 C37 C38 C39 C40 C41 C42 C43 C44 C48 C50 C51 C52,53 –1– VCEAZA1EW476M VCTYMN1CY103N VCEAZA1EW476M VCKYMN1HB102K VCQYKA1HM473K VCTYPA1CX104K VCTYMN1CX272K VCEAZA1AW107M VCEAZA1HW106M VCEAZA1HW224M VCKYMN1HB101K VCTYMN1EF223Z VCEAZA1AW107M VCEAZA0JW337M VCEAZA1AW107M RC-EZ0004AWZZ VCTYMN1CY103N VCEAZA1HW106M VCQYKA1HM152K VCTYMN1EF223Z VCKYMN1HB101K VCKYMN1HB101K VCKYMN1HB101K VCTYMN1EF223Z VCKYMN1HB101K VCQYKA1HM473K VCEAZA1HW224M VCTYPA1CX104K VCTYMN1CY103N VCEAZA1AW107M VCEAZA0JW227M VCEAZA1AW107M VCTYMN1CY103N VCEAZA1AW107M VCKYMN1HB102K VCTYMN1EF223Z VCCCMN1HH220J VCKYPA1HF223Z VCKYMN1HB102K XL-HP500 NO. C54,55 C59 C103,104 C105,106 C109,110 C111,112 C113,114 C115,116 C117,118 C121 C123,124 C125,126 C127,128 C129,130 C131,132 C133 C134 C135 C137 C138 C139 C140 C141 C143 C302 C303 C304 C305 C306 C307 C308 C309 C310 C311 C312 C313 C314,315 C316 C317 C318 C322 C323 C324 C330 C331 C332 C334 C335 C338 C342 C350 C351 C352 C353,354 C355 C356 C357 C358 C361 C362 C363 C364 C365 C366 C367,368 C369 C370~372 C373,374 C380 C381 C382 C384 C385 C386 C387 C388 C389 C390 C391 C392 C393 C394 PART CODE VCTYMN1EF223Z VCTYPA1CX103K VCKYMN1HB181K VCKYMN1HB561K VCKYMN1HB331K RC-EZY107AF1C VCTYPA1EX333K VCKYMN1HB561K RC-EZY476AF1E VCTYMN1EF223Z VCKYMN1HB271K RC-EZY226AF1C VCTYPA1CX223K VCTYMN1CX332K RC-EZY476AF1E RC-EZY226AF1C RC-EZY227AF1A VCTYMN1EF223Z VCQYKA1HM473K VCQPKA2AA822J VCQYKA1HM393K VCEAZA1EW476M RC-EZY107AF1C RC-EZY335AF1H VCKYMN1HB102K VCCCMN1HH100J VCTYMN1CY103N VCCCMN1HH4R7C VCTYMN1EF223Z RC-EZY106AF1C VCCCMN1HH4R7C VCKYMN1HB102K VCCCMN1HH150J VCCSMN1HL180J VCTYMN1EF223Z VCCCMN1HH220J VCTYMN1CX472K VCTYMN1EF223Z VCKYMN1HB102K VCKYMN1HB101K VCKYPA1HB101K VCTYMN1EF223Z VCCUMN1HJ4R7D VCCUMN1HJ150J VCKYPA1HF473Z VCTYMN1EF223Z VCCUMN1HJ220J VCKYMN1HB561K VCKYMN1HB102K VCTYMN1EF223Z VCKYPA1HF223Z VCTYMN1EF223Z RC-EZY106AF1C VCTYMN1EF223Z VCCSMN1HL220J VCKYMN1HB102K RC-EZY225AF1H RC-EZY105AF1H VCTYMN1EF223Z VCEAZA1HW335M VCTYMN1EF223Z VCEAZA1HW225M VCKYPA1HF223Z VCKYMN1HB102K VCEAZA1HW105M VCCUMN1HJ270J VCEAZA1HW105M VCTYPA1CX273K RC-EZY106AF1C VCCCMN1HH120J VCCCMN1HH150J VCKYMN1HB102K VCTYMN1CY103N VCKYMN1HB331K VCTYMN1EF223Z VCKYMN1HB102K RC-EZY105AF1H VCKYBT1HB101K RC-EZY476AF1C VCKYMN1HB102K VCKYPA1HB121K RC-EZY476AF1C J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J PRICE RANK DESCRIPTION AA AA AA AA AA AB AA AA AB AA AA AB AA AA AB AB AB AA AB AA AB AB AB AB AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AB AA AB AA AA AA AB AB AA AB AA AB AB AA AB AA AB AA AB AA AA AA AA AA AA AA AB AA AB AA AA AB 0.022 µF,25V 0.01 µF,16V 180 pF,50V 560 pF,50V 330 pF,50V 100 µF,16V,Electrolytic 0.033 µF,25V 560 pF,50V 47 µF,25V,Electrolytic 0.022 µF,25V 270 pF,50V 22 µF,16V,Electrolytic 0.022 µF,16V 0.0033 µF,16V 47 µF,25V,Electrolytic 22 µF,16V,Electrolytic 220 µF,10V,Electrolytic 0.022 µF,25V 0.047 µF,50V,Mylar 0.0082 µF,100V,Polypropylene 0.039 µF,50V,Mylar 47 µF,25V,Electrolytic 100 µF,16V,Electrolytic 3.3 µF,50V,Electrolytic 0.001 µF,50V 10 pF (CH),50V 0.01 µF,16V 4.7 pF (CH),50V 0.022 µF,25V 10 µF,16V,Electrolytic 4.7 pF (CH),50V 0.001 µF,50V 15 pF (CH),50V 18 pF,50V 0.022 µF,25V 22 pF (CH),50V 0.0047 µF,16V 0.022 µF,25V 0.001 µF,50V 100 pF,50V 100 pF,50V 0.022 µF,25V 4.7 pF (UJ),50V 15 pF (UJ),50V 0.047 µF,50V 0.022 µF,25V 22 pF (UJ),50V 560 pF,50V 0.001 µF,50V 0.022 µF,25V 0.022 µF,50V 0.022 µF,25V 10 µF,16V,Electrolytic 0.022 µF,25V 22 pF,50V 0.001 µF,50V 2.2 µF,50V,Electrolytic 1 µF,50V,Electrolytic 0.022 µF,25V 3.3 µF,50V,Electrolytic 0.022 µF,25V 2.2 µF,50V,Electrolytic 0.022 µF,50V 0.001 µF,50V 1 µF,50V,Electrolytic 27 pF (UJ),50V 1 µF,50V,Electrolytic 0.027 µF,16V 10 µF,16V,Electrolytic 12 pF (CH),50V 15 pF (CH),50V 0.001 µF,50V 0.01 µF,16V 330 pF,50V 0.022 µF,25V 0.001 µF,50V 1 µF,50V,Electrolytic 100 pF,50V 47 µF,16V,Electrolytic 0.001 µF,50V 120 pF,50V 47 µF,16V,Electrolytic NO. –2– C395 C396 C397 C398 C399 C502 C601 C602 C603 C605~608 C609,610 C611,612 C613,614 C615,616 C617~624 C625,626 C631,632 C635~638 C639 C640 C641~643 C651~653 C690,691 C700 C701 C702 C703 C704 C705 C706 C707 C708~717 C718 C719 C720 C721 C722 C801 C802,803 C804 C805 C806~809 C841 C842 C843 1 C844 C851 C852 C853 C854,855 C856 C857 C858,859 C860 C861 C862 C863 C864 C865 C901,902 C903,904 C905,906 C907,908 C909,910 C911,912 C913,914 C915,916 C925 C926~929 C930 C931 C932 C948,949 C960 PRICE RANK PARTS CODE VCTYMN1EF223Z RC-EZY107AF1A VCTYMN1EF223Z RC-EZY107AF1A VCTYMN1EF223Z RC-EZY476AF1E RC-EZY227AF1C VCTYMN1EF223Z RC-EZY226AF1C VCFYDA1HA154J RC-EZY105AF1H VCTYMN1CX222K RC-EZY105AF1H RC-EZY475AF1H RC-EZY105AF1H VCKYMN1HB101K VCTYMN1CX222K VCKYMN1HB102K VCEAZA1HW225M VCEAZA1HW226M VCKYPA1HB102K VCKYMN1HB221K VCKYMN1HB391K RC-EZY105AF1H RC-EZY227AF1A VCTYMN1EF223Z VCCSMN1HL150J VCCSMN1HL180J VCTYMN1EF223Z VCEAZA1EW476M RC-EZY105AF1H VCKYMN1HB102K VCTYMN1CY103N VCEAZA1HW335M VCTYMN1EF223Z RC-EZY476AF1E VCKYMN1HB151K VCEAZA1VW107M VCEAZA1HW476M VCEAZA1JW227M VCEAZA2AW226M VCFYHA1HA104J VCEAZA0JW108M VCEAZA1VW477M VCQYKA1HM473K RC-KZ002LAWZZ VCKYPA1HF473Z VCEAZA1HW226M VCEAZA1EW476M VCQYKA1HM104K VCEAZW1VW338M VCEAZA1EW476M VCQYKA1HM104K VCEAZA1EW476M VCKYPA1HF473Z VCEAZA1HW106M VCEAZA1HW226M VCQYKA1HM104K VCEAZA1HW106M VCEAZA1HW224M VCKYPA1HB102K VCCSPA1HL3R0C VCKYMN1HB471K VCEAZA1CW226M VCQYKA1HM223K VCEAZA1JW107M VCEAZA1JW106M VCEAZA1HW476M VCFYHA1HA224J VCEAZA1HW476M VCEAZA1HW106M VCFYHA1HA224J RC-EZ0104AWZZ VCEAZA1EW335M DESCRIPTION J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AA AB AA AB AA AB AC AA AB AB AB AA AB AB AB AA AA AA AB AB AA AA AA AB AB AA AA AA AA AB AB AA AA AB AA AB AA AC AB AD AC AB AC AD AB AC AB AB AB AB AH AB AB AB AB AB AB AB AB AB AA AA AA AC AB AC AB AB AC AB AB AC AH AB 0.022 µF,25V 100 µF,10V,Electrolytic 0.022 µF,25V 100 µF,10V,Electrolytic 0.022 µF,25V 47 µF,25V,Electrolytic 220 µF,16V,Electrolytic 0.022 µF,25V 22 µF,16V,Electrolytic 0.15 µF,50V,Polyester 1 µF,50V,Electrolytic 0.0022 µF,16V 1 µF,50V,Electrolytic 4.7 µF,50V,Electrolytic 1 µF,50V,Electrolytic 100 pF,50V 0.0022 µF,16V 0.001 µF,50V 2.2 µF,50V,Electrolytic 22 µF,50V,Electrolytic 0.001 µF,50V 220 pF,50V 390 pF,50V 1 µF,50V,Electrolytic 220 µF,10V,Electrolytic 0.022 µF,25V 15 pF,50V 18 pF,50V 0.022 µF,25V 47 µF,25V,Electrolytic 1 µF,50V,Electrolytic 0.001 µF,50V 0.01 µF,16V 3.3 µF,50V,Electrolytic 0.022 µF,25V 47 µF,25V,Electrolytic 150 pF,50V 100 µF,35V,Electrolytic 47 µF,50V,Electrolytic 220 µF,63V,Electrolytic 22 µF,50V,Electrolytic 0.1 µF,100V,Thin Film 1000 µF,6.3V,Electrolytic 470 µF,35V,Electrolytic 0.047 µF,50V,Mylar 0.0047 µF,250V,Ceramic 0.047 µF,50V 22 µF,50V,Electrolytic 47 µF,25V,Electrolytic 0.1 µF,50V,Mylar 3300 µF,35V,Electrolytic 47 µF,25V,Electrolytic 0.1 µF,50V,Mylar 47 µF,25V,Electrolytic 0.047 µF,50V 10 µF,50V,Electrolytic 22 µF,50V,Electrolytic 0.1 µF,50V,Mylar 10 µF,50V,Electrolytic 0.22 µF,50V,Electrolytic 0.001 µF,50V 3 pF,50V 470 pF,50V 22 µF,16V,Electrolytic 0.022 µF,50V,Mylar 100 µF,63V,Electrolytic 10 µF,63V,Electrolytic 47 µF,50V,Electrolytic 0.22 µF,50V,Thin Film 47 µF,50V,Electrolytic 10 µF,50V,Electrolytic 0.22 µF,50V,Thin Film 2200 µF,50V,Electrolytic 3.3 µF,25V,Electrolytic J J J J J AA AA AA AA AA 0 ohm,Jumper,ø1.4×3.5mm,Ivory 8.2 kohms,1/8W 22 kohms,1/8W 8.2 kohms,1/8W 22 kohms,1/8W RESISTORS R1,2 R3 R4,5 R6 VRD-MN2BD000C VRD-MN2BD822J VRD-MN2BD223J VRD-MN2BD822J VRD-MN2BD223J XL-HP500 NO. R7 R9 R10 R11 R12 R13~16 R18 R20 R22 R23 R24,25 R26,27 R28,29 R30,31 R32~38 R39,40 R41 R42 R43 R44 R45,46 R47 R49,50 1 R51 R52 R103,104 R105,106 R107,108 R109,110 R111,112 R113 R114 R115 R116 R117,118 R119,120 R121,122 R123,124 R126,127 R128,129 R130,131 R132,133 R134,135 R136,137 R138 R139 R140 R141 R142 R143 R144 R145 R146,147 R148 R149 R150 R158 R302 R309 R311 R313 R314 R316 R322 R323 R325 R327 R336 R350 R351 R352 R353 R355 R356 R357 R358 R359 R360 R361,362 R363,364 R365 R372~374 PRICE RANK PART CODE VRD-ST2CD470J VRD-MN2BD100J VRD-ST2CD273J VRD-MN2BD103J VRD-MN2BD331J VRD-MN2BD102J VRD-MN2BD102J VRD-MN2BD103J VRD-ST2CD101J VRD-MN2BD221J VRD-MN2BD152J VRD-MN2BD103J VRD-MN2BD222J VRD-ST2CD222J VRD-ST2CD102J VRD-MN2BD681J VRD-MN2BD123J VRD-MN2BD122J VRD-MN2BD221J VRD-ST2CD123J VRD-MN2BD272J VRD-MN2BD101J VRD-ST2EE1R0J VRG-ST2EG3R3J VRD-ST2CD472J VRD-MN2BD222J VRD-MN2BD332J VRD-MN2BD473J VRD-MN2BD472J VRD-ST2CD153J VRD-MN2BD102J VRD-ST2CD102J VRD-ST2CD560J VRD-MN2BD560J VRD-MN2BD104J VRD-MN2BD392J VRD-MN2BD123J VRD-MN2BD682J VRD-MN2BD472J VRD-MN2BD562J VRD-MN2BD152J VRD-MN2BD101J VRD-MN2BD103J VRD-ST2CD224J VRD-ST2CD103J VRD-MN2BD103J VRD-MN2BD473J VRD-ST2CD472J VRD-RT2HD820J VRD-MN2BD473J VRD-MN2BD223J VRD-ST2CD4R7J VRD-MN2BD103J VRD-MN2BD472J VRD-ST2EE151J VRD-MN2BD683J VRD-ST2EE221J VRD-MN2BD100J VRD-ST2CD103J VRD-MN2BD104J VRD-MN2BD333J VRD-ST2CD220J VRD-MN2BD472J VRD-MN2BD681J VRD-MN2BD683J VRD-MN2BD473J VRD-MN2BD330J VRD-MN2BD103J VRD-MN2BD272J VRD-MN2BD562J VRD-MN2BD102J VRD-MN2BD271J VRD-MN2BD332J VRD-MN2BD102J VRD-ST2CD474J VRD-ST2CD392J VRD-MN2BD182J VRD-MN2BD472J VRD-MN2BD222J VRD-MN2BD393J VRD-MN2BD103J VRD-MN2BD102J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA DESCRIPTION 47 ohms,1/6W 10 ohm,1/8W 27 kohms,1/6W 10 kohm,1/8W 330 ohms,1/8W 1 kohm,1/8W 1 kohm,1/8W 10 kohm,1/8W 100 ohm,1/6W 220 ohms,1/8W 1.5 kohms,1/8W 10 kohm,1/8W 2.2 kohms,1/8W 2.2 kohms,1/6W 1 kohm,1/6W 680 ohms,1/8W 12 kohms,1/8W 1.2 kohms,1/8W 220 ohms,1/8W 12 kohms,1/6W 2.7 kohms,1/8W 100 ohm,1/8W 1 ohm,1/4W 3.3 ohms,1/4W,Fusible 4.7 kohms,1/6W 2.2 kohms,1/8W 3.3 kohms,1/8W 47 kohms,1/8W 4.7 kohms,1/8W 15 kohms,1/6W 1 kohm,1/8W 1 kohm,1/6W 56 ohms,1/6W 56 ohms,1/8W 100 kohm,1/8W 3.9 kohms,1/8W 12 kohms,1/8W 6.8 kohms,1/8W 4.7 kohms,1/8W 5.6 kohms,1/8W 1.5 kohms,1/8W 100 ohm,1/8W 10 kohm,1/8W 220 kohms,1/6W 10 kohm,1/6W 10 kohm,1/8W 47 kohms,1/8W 4.7 kohms,1/6W 82 ohms,1/2W 47 kohms,1/8W 22 kohms,1/8W 4.7 ohms,1/6W 10 kohm,1/8W 4.7 kohms,1/8W 150 ohms,1/4W 68 kohms,1/8W 220 ohms,1/4W 10 ohm,1/8W 10 kohm,1/6W 100 kohm,1/8W 33 kohms,1/8W 22 ohms,1/6W 4.7 kohms,1/8W 680 ohms,1/8W 68 kohms,1/8W 47 kohms,1/8W 33 ohms,1/8W 10 kohm,1/8W 2.7 kohms,1/8W 5.6 kohms,1/8W 1 kohm,1/8W 270 ohms,1/8W 3.3 kohms,1/8W 1 kohm,1/8W 470 kohms,1/6W 3.9 kohms,1/6W 1.8 kohms,1/8W 4.7 kohms,1/8W 2.2 kohms,1/8W 3.9 kohms,1/8W 10 kohm,1/8W 1 kohm,1/8W NO. R375 R376 R377 R378 R379 R380 R381 R382 R383 R384 R385 R386 R387 R388 R390 R391,392 R393 R395 R504 R505 R506,507 R601 R602 R603 R604,605 R606,607 R608,609 R610,611 R612 R613 R614,615 R616,617 R618,619 R620,621 R641,642 R645,646 R690,691 R692,693 R700 R702~706 R708 R709,710 R711 R712,713 R714~717 R720,721 R723 R724 R725~730 R731 R732 R733 R734 R735,736 R737 R744 R745 R746 R747 R748~756 R757~761 R762 R763 R764 R765 R766 R767~774 R780,781 R782 R783~786 R787 R789 R790 R793,794 R795 R796 R797 R798 R799 R801 R802 R803 –3– PRICE RANK PARTS CODE VRD-ST2CD471J VRD-MN2BD102J VRD-MN2BD473J VRD-MN2BD472J VRD-MN2BD222J VRD-MN2BD152J VRD-MN2BD103J VRD-ST2EE151J VRD-MN2BD562J VRD-ST2CD562J VRD-MN2BD562J VRD-ST2CD103J VRD-ST2CD562J VRD-MN2BD392J VRD-ST2CD823J VRD-ST2EE271J VRD-MN2BD102J VRD-MN2BD473J VRD-MN2BD472J VRD-MN2BD822J VRD-MN2BD103J VRD-ST2CD102J VRD-MN2BD102J VRD-ST2CD102J VRD-ST2CD103J VRD-MN2BD332J VRD-MN2BD103J VRD-MN2BD222J VRD-MN2BD391J VRD-ST2CD391J VRD-MN2BD332J VRD-MN2BD222J VRD-MN2BD331J VRD-MN2BD223J VRD-ST2CD103J VRD-ST2CD183J VRD-MN2BD682J VRD-ST2CD393J VRD-ST2CD102J VRD-ST2CD102J VRD-ST2CD102J VRD-MN2BD102J VRD-ST2CD102J VRD-MN2BD102J VRD-ST2CD102J VRD-ST2CD102J VRD-ST2CD102J VRD-MN2BD102J VRD-ST2CD102J VRD-MN2BD681J VRD-ST2CD681J VRD-MN2BD222J VRD-MN2BD561J VRD-ST2CD102J VRD-MN2BD102J VRD-MN2BD102J VRD-ST2CD102J VRD-MN2BD102J VRD-ST2CD102J VRD-MN2BD102J VRD-MN2BD103J VRD-ST2CD330J VRD-MN2BD473J VRD-ST2CD102J VRD-MN2BD104J VRD-ST2EE1R5J VRD-MN2BD562J VRD-MN2BD103J VRD-MN2BD472J VRD-MN2BD103J VRD-ST2CD103J VRD-ST2CD103J VRD-ST2CD562J VRD-MN2BD103J VRD-ST2EE1R5J VRD-MN2BD473J VRD-MN2BD104J VRD-MN2BD101J VRD-MN2BD103J VRD-ST2CD104J VRD-ST2CD473J VRD-ST2CD123J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA DESCRIPTION 470 ohms,1/6W 1 kohm,1/8W 47 kohms,1/8W 4.7 kohms,1/8W 2.2 kohms,1/8W 1.5 kohms,1/8W 10 kohm,1/8W 150 ohms,1/4W 5.6 kohms,1/8W 5.6 kohms,1/6W 5.6 kohms,1/8W 10 kohm,1/6W 5.6 kohms,1/6W 3.9 kohms,1/8W 82 kohms,1/6W 270 ohms,1/4W 1 kohm,1/8W 47 kohms,1/8W 4.7 kohms,1/8W 8.2 kohms,1/8W 10 kohm,1/8W 1 kohm,1/6W 1 kohm,1/8W 1 kohm,1/6W 10 kohm,1/6W 3.3 kohms,1/8W 10 kohm,1/8W 2.2 kohms,1/8W 390 ohms,1/8W 390 ohms,1/6W 3.3 kohms,1/8W 2.2 kohms,1/8W 330 ohms,1/8W 22 kohms,1/8W 10 kohm,1/6W 18 kohms,1/6W 6.8 kohms,1/8W 39 kohms,1/6W 1 kohm,1/6W 1 kohm,1/6W 1 kohm,1/6W 1 kohm,1/8W 1 kohm,1/6W 1 kohm,1/8W 1 kohm,1/6W 1 kohm,1/6W 1 kohm,1/6W 1 kohm,1/8W 1 kohm,1/6W 680 ohms,1/8W 680 ohms,1/6W 2.2 kohms,1/8W 560 ohms,1/8W 1 kohm,1/6W 1 kohm,1/8W 1 kohm,1/8W 1 kohm,1/6W 1 kohm,1/8W 1 kohm,1/6W 1 kohm,1/8W 10 kohm,1/8W 33 ohms,1/6W 47 kohms,1/8W 1 kohm,1/6W 100 kohm,1/8W 1.5 ohms,1/4W 5.6 kohms,1/8W 10 kohm,1/8W 4.7 kohms,1/8W 10 kohm,1/8W 10 kohm,1/6W 10 kohm,1/6W 5.6 kohms,1/6W 10 kohm,1/8W 1.5 ohms,1/4W 47 kohms,1/8W 100 kohm,1/8W 100 ohm,1/8W 10 kohm,1/8W 100 kohm,1/6W 47 kohms,1/6W 12 kohms,1/6W XL-HP500 NO. R804,805 R806 R807 R808 R841 R842 R843 R852 R853,854 R856 R857 R858 R859 R860 R901,902 R903,904 R907,908 R909,910 R911,912 R913,914 R915,916 R917~920 1 R921,922 R923,924 R925 R926,927 R935~937 R940,941 R944,945 R946 R947 R949 R950 R961,962 R965,966 R967 RD01 RD02 RD03 RD04 RD05 RD06 RD07 RD11 RD12 RD13 RD14 RD15 RD16 RD17 RD18 RD19 RD20 RD21 RD22 RD23 RD24 RD25 PRICE RANK PART CODE VRD-ST2EE470J VRD-ST2CD473J VRD-ST2EE100J VRD-RT2HD222J VRD-ST2CD224J VRD-ST2CD102J VRD-ST2CD473J VRD-ST2CD103J VRD-ST2CD223J VRD-RT2HD1R0J VRD-RT2HD3R3J VRD-ST2CD221J VRD-ST2CD223J VRD-ST2EE221J VRD-ST2CD563J VRD-MN2BD102J VRD-ST2CD563J VRD-MN2BD102J VRD-MN2BD821J VRN-VV3AAR10J VRD-MN2BD562J VRN-VV3DAR22J VRG-ST2EC101J VRD-MN2BD102J VRD-MN2BD223J VRD-ST2CD223J VRD-MN2BD563J VRD-RT2HD4R7J VRD-ST2CD222J VRD-ST2CD473J VRD-ST2CD153J VRD-RT2HD102J VRD-ST2CD683J VRD-RT2HD331J VRD-RT2HD822J VRD-RT2HD681J VRD-MN2BD681J VRD-MN2BD821J VRD-MN2BD102J VRD-MN2BD152J VRD-MN2BD222J VRD-MN2BD272J VRD-MN2BD392J VRD-MN2BD681J VRD-MN2BD821J VRD-ST2CD102J VRD-MN2BD152J VRD-ST2CD222J VRD-MN2BD272J VRD-MN2BD392J VRD-MN2BD562J VRD-ST2CD681J VRD-MN2BD821J VRD-MN2BD102J VRD-MN2BD152J VRD-MN2BD222J VRD-MN2BD272J VRD-MN2BD392J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J DESCRIPTION AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AC AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 47 ohms,1/4W 47 kohms,1/6W 10 ohm,1/4W 2.2 kohms,1/2W 220 kohms,1/6W 1 kohm,1/6W 47 kohms,1/6W 10 kohm,1/6W 22 kohms,1/6W 1 ohm,1/2W 3.3 ohms,1/2W 220 ohms,1/6W 22 kohms,1/6W 220 ohms,1/4W 56 kohms,1/6W 1 kohm,1/8W 56 kohms,1/6W 1 kohm,1/8W 820 ohms,1/8W 0.1 ohm,1W 5.6 kohms,1/8W 0.22 ohms,2W 100 ohm,1/4W,Fusible 1 kohm,1/8W 22 kohms,1/8W 22 kohms,1/6W 56 kohms,1/8W 4.7 ohms,1/2W 2.2 kohms,1/6W 47 kohms,1/6W 15 kohms,1/6W 1 kohm,1/2W 68 kohms,1/6W 330 ohms,1/2W 8.2 kohms,1/2W 680 ohms,1/2W 680 ohms,1/8W 820 ohms,1/8W 1 kohm,1/8W 1.5 kohms,1/8W 2.2 kohms,1/8W 2.7 kohms,1/8W 3.9 kohms,1/8W 680 ohms,1/8W 820 ohms,1/8W 1 kohm,1/6W 1.5 kohms,1/8W 2.2 kohms,1/6W 2.7 kohms,1/8W 3.9 kohms,1/8W 5.6 kohms,1/8W 680 ohms,1/6W 820 ohms,1/8W 1 kohm,1/8W 1.5 kohms,1/8W 2.2 kohms,1/8W 2.7 kohms,1/8W 3.9 kohms,1/8W AL AF AG AG AF AB AB AC AC AB AC AC AC AB AC AB AC AC AD AB AC Connector Ass’y,8/6Pin Connector Ass’y,6/5Pin Connector Ass’y,8/7Pin Connector Ass’y,9/8Pin Connector Ass’y,5/5Pin Plug,7Pin Plug,8Pin Plug,6Pin Plug,6Pin Plug,4Pin Socket,7Pin Socket,7Pin Socket,13Pin Plug,5Pin Socket,13Pin Plug,6Pin Plug,8Pin Plug,3Pin Socket,16Pin Plug,5Pin Plug,7Pin NO. CNP971 CNS1A/B CNS2A/B CNS3A/B CNS4 CNS8 CNS702 CNS971 1 F801,802 1 F803,804 FC5 FC6 FC701 FC702 FL701 FW804 FW804A/B FW902 FW903 HD902 HD903 JK690 JK951 JK953 M1 M2 M971(212-3) MOB1 MOB2 1 RL841 1 RL914 RX701 SO901 SW4 SW701 OTHER CIRCUITRY PARTS BI102 QCNWN2432AWZZ BI706/CNS706 QCNWN2425AWZZ BI801/CNS801 QCNWN2393AWZZ BI901/CNS9 QCNWN2431AWZZ BIM2/CNS7 QCNWN2416AWZZ CNP1 QCNCM705GAFZZ CNP2 QCNCM705HAFZZ CNP3 92LCONE6P53253 CNP3A 92LCONE6P53254 CNP4 92LCONE4P53253 CNP5 QCNCWZF07AWZZ CNP5A QCNCWZY07AWZZ CNP6 QCNCWZF13AWZZ CNP7 92LCONE5P53253 CNP7A QCNCWZY13AWZZ CNP8 QCNCM705FAFZZ CNP9 92LCONE8P53254 CNP302 92LCONE3P5268 CNP701A,701B QCNCWZX16AWZZ CNP706 92LCONE5P53253 CNP801 92LCONE7P5267X J J J J J J J J J J J J J J J J J J J J J PRICE RANK PARTS CODE 92LCONE2P53253 QCNWN0858AWZZ QCNWN0859AWZZ QCNWN2412AWZZ QCNWN2414AWZZ QCNWN2413AWZZ QCNCWZY07AWZZ QCNWN1389AWZZ QFS-D402DAWNI QFS-D202DAWNI QCNWN2395AWZZ QCNWN2397AWZZ QCNWN2409AWZZ QCNWN2394AWZZ VVKNA10SS23-1 QCNWN2508AWZZ QCNCW015DAWZZ QCNWN2392AWZZ QCNWN2447AWZZ QCNCW019EAWZZ QCNCW019CAWZZ QSOCJ0224AWZZ QJAKM0004AWZZ QSOCJ0111AWZZ 92LMTR2996CASY 92LMTR1854BASY RMOTV0027AWZZ 92LMTR2395DASY 92LMTR2395DASY RRLYD0018AWZZ RRLYD0014AWZZ VHLGP1UM271-1 QTANA0424AWZZ QSW-F9001AW01 92LSWICHT1663T J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AB AG AF AG AE AE AC AC AC AC AD AF AF AE AW SW702 SW703 SW704 92LSWICHT1663T 92LSWICHT1663T 92LSWICHT1663T J J J AC AC AC SW705 92LSWICHT1663T J AC SW706 SW707 92LSWICHT1663T 92LSWICHT1663T J J AC AC SW708 SW712 SW713 92LSWICHT1663T 92LSWICHT1663T 92LSWICHT1663T J J J AC AC AC SW714 SW715 SW716 92LSWICHT1663T 92LSWICHT1663T 92LSWICHT1663T J J J AC AC AC SW717 SW718 92LSWICHT1663T 92LSWICHT1663T J J AC AC SW719 SW720 SW721 SW722 SW723 SW724 SW725 SW726 SW727 SW728 92LSWICHT1663T 92LSWICHT1663T 92LSWICHT1663T 92LSWICHT1663T 92LSWICHT1663T 92LSWICHT1663T 92LSWICHT1663T 92LSWICHT1663T 92LSWICHT1663T 92LSWICHT1663T J J J J J J J J J J AC AC AC AC AC AC AC AC AC AC SWB101/102 SWB103/104 SWB105 SWB106 QSW-F0353AFZZ QSW-F0353AFZZ QSW-P0920AFZZ QSW-P0920AFZZ J J J J AD AD AC AC SWB107 SWB108 VR701 WT902 WT904 QSW-P0920AFZZ QSW-P0920AFZZ QSW-Z0013AWZZ QCNCW012EAWZZ QCNCW012CAWZZ J J J J J AC AC AF AC AC AB AC AB AB AB AC AK AD AS AP AM AQ AQ AH AK AH AE AD AC DESCRIPTION Plug,2Pin Connector Ass’y,7/7Pin Connector Ass’y,8/8Pin Connector Ass’y,6/6Pin Connector Ass’y,4Pin Connector Ass’y,6Pin Socket,7Pin Connector Ass’y,2Pin Fuse,4A,125V Fuse,2A,125V Flat Cable,7Pin Flat Cable,13Pin Flat Cable,16Pin Flat Cable,7Pin FL Display Flat Wire,4Pin Holder,Flat Cable Flat Wire,5Pin Flat Wire,3Pin Holder,Flat Wire,5Pin Holder,Flat Wire,3Pin Jack,Video/AUX Jack,Headphones Sub Woofer Output Motor with Chassis [Spindle] Motor with Gear [Sled] Motor,Air Cooling Fan Main Cam Motor Ass’y Tray Motor Ass’y Relay Relay Remote Sensor,GP1UM271 Terminal,Speaker Switch,Leaf Type [PICKUP IN] Switch,Key Type [POWER ON/STAND BY] Switch,Key Type [CLOCK] Switch,Key Type [TIMER/SLEEP] Switch,Key Type [TUNING/TIME UP] Switch,Key Type [TUNING/TIME DOWN] Switch,Key Type [REC/PAUSE] Switch,Key Type [REVERSE MODE] Switch,Key Type [MEMORY/SET] Switch,Key Type [PRESET UP] Switch,Key Type [PRESET DOWN] Switch,Key Type [PLAY] Switch,Key Type [STOP] Switch,Key Type [REVERSE PLAY] Switch,Key Type [CD] Switch,Key Type [TUNER (BAND)] Switch,Key Type [TAPE] Switch,Key Type [VIDEO/AUX] Switch,Key Type [DISC 3 EJECT] Switch,Key Type [DISC 2 EJECT] Switch,Key Type [DISC 1 EJECT] Switch,Key Type [DISC 1] Switch,Key Type [DISC 2] Switch,Key Type [DISC 3] Switch,Key Type [EQUALIZER] Switch,Key Type [X-BASS/DEMO] Switch,Leaf Type [CAM1,2] Switch,Leaf Type [CAM3,4] Switch,Push Type [CD EJECT] Switch,Push Type [CD TRAY CLOSE] Switch,Push Type [CD IN] Switch,Push Type [CD SET] Switch,Push Type [VOLUME] Socket,5Pin Socket,3Pin CD MECHANISM PARTS 301 302 –4– NGERH0011AWZZ J NGERH0012AWZZ J AC Gear,Middle AC Gear,Drive XL-HP500 NO. PRICE RANK PART CODE 303 304 305 1 306 306- 1 MLEVP0080AWZZ NSFTM0020AWFW 92LMCUSN1524A 92LHPC1LXASY ———— J J J J AC AD AD BD — 306- 2 306- 3 307 308 701 702 703 704 M1 M2 SW4 NGERR0043AFZZ MSPRC0961AFZZ PCUSG0001AWSA PCUSG0004AWSA XBSSD26P06000 XHBSD20P05000 XBBSD20P03000 LX-WZ1070AFZZ 92LMTR2996CASY 92LMTR1854BASY QSW-F9001AW01 J J J J J J J J J J J AC AA AD AD AA AA AA AA AS AP AD DESCRIPTION Rail,Guide Shaft,Guide Cushion Pickup Unit Ass’y Pickup Unit (Not Replacement Item) Gear,Rack Spring,Rack Cushion Cushion Screw,ø2.6×6mm Screw,ø2×5mm Screw,ø2×3mm Washer,ø1.5×ø3.8×0.25mm Motor with Chassis [Spindle] Motor with Gear [Sled] Switch,Leaf Type [Pickup In] CHANGER MECHANISM PARTS 101 102 103 104 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 801 802 803 804 805 806 MOB1 MOB2 SWB101/102 SWB103/104 SWB105 SWB106 GCOVA1152AWZZ GCOVA1153AWZZ LANGF0024AWZZ LANGF0025AWZZ LANGF0028AWZZ LANGK0169AWZZ LCHSM0037AWZZ LCHSM0038AWZZ LHLDM1008AWZZ MCAMP0127AFZZ MLEVP0052AWZZ MLEVP0053AWZZ MLEVP0054AWZZ MLEVP0055AWZZ MLEVP0056AWZZ MLEVP0057AWM1 MLEVP0058AWZZ MSPRD0078AWFJ MSPRD0079AWFJ MSPRD0080AWFJ NBLTK0027AWZZ NGERH0052AWZZ NGERH0053AWZZ NGERH0054AWZZ NGERH0055AWZZ NGERH0056AWZZ NGERH0057AWZZ NGERH0058AWZZ NPLYR0004AWZZ NROLP0007AWZZ NSFTL0001AWZZ PGIDM0017AWZZ PGIDM0018AWZZ PGIDM0019AWZZ PGUMS0016AWZZ PMAGF0001AWZZ 92LNBAND1318A MSPRD0184AWFJ LX-EZ0005AWFD XBPSD26P04000 XBPSD30P03000 XEBSD20P06000 XEBSD20P07000 XEBSD26P12000 92LMTR2395DASY 92LMTR2395DASY QSW-F0353AFZZ QSW-F0353AFZZ QSW-P0920AFZZ QSW-P0920AFZZ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J SWB107 SWB108 QSW-P0920AFZZ QSW-P0920AFZZ J J AL AF AE AB AB AF AP AK AD AR AC AC AC AC AC AC AB AB AB AB AB AC AB AB AC AB AB AB AC AB AB AC AF AE AB AF AA AB AA AA AA AA AB AA AQ AQ AD AD AC AC Tray,Disc Guide Tray,Disc Top Board Bracket,Switch Bracket,Mecha Holder Stopper Main Base Changer Box Stabilizer Main Cam Lever,Tray Change Lever,Top Joint Lever,Midle Joint Lever,Bottom Joint Lever,Front Switch Lever,Rear Switch Ass’y Lever,Tray Lock Spring,Tray Switch Spring,Disc Top Spring,Tray Lock Lever Belt,Cam Drive Gear,Idler Gear,Cam Gear,Midle Gear,Center Gear,Center Tray Gear,Tray Idler Gear,Tray Drive Pulley,Drive Rollar,Cam Guide Shaft,Tray Change Guide,Mecha Holder Holder,Mecha Stabilizer Holder Tray Rubber Magnet Nylon Band,80mm Spring,Tray Switch B Screw,Special Screw,ø2.6×4mm Screw,ø3×3mm Screw,ø2×6mm Screw,ø2×7mm Screw,ø2.6×12mm Main Cam Motor Ass’y Tray Motor Ass’y Switch,Leaf Type [CAM1,2] Switch,Leaf Type [CAM3,4] Switch,Push Type [CD EJECT] Switch,Push Type [CD TRAY CLOSE] AC Switch,Push Type [CD IN] AC Switch,Push Type [CD SET] CABINET PARTS 201 201- 1 92LCAB4763AASY J ———— 201- 2 201- 3 GCOVA1364AWSA J GCOVA1460AWSA J BB Front Panel Ass’y — Front Panel (Not Replacement Item) AB Indicator,Timer AC Cover,Sensor NO. PRICE RANK PARTS CODE 201- 4 201- 5 201- 6 201- 7 201- 8 201- 9 201-10 201-11 201-12 201-13 201-14 201-16 201-17 201-18 201-19 202 202- 1 GCOVA1461AWSA GDORF0117AWSA HBDGB1001AWSA HDECQ0936AWSA HDECQ0937AWSA HDECZ0026AWSA JKNBZ0904AWSB JKNBZ0905AWSA JKNBZ0906AWSA JKNBZ0907AWSA JKNBZ0908AWSA LHLDZ9008AWSA MLIFP0008AWZZ MSPRD0180AWFJ QCNWN1860AWZZ 92LCAB4782BASY ———— J J J J J J J J J J J J J J J J AK AF AD AG AD AP AF AF AG AG AF AC AD AB AC AP — 202- 2 203 203- 1 PCUSG0022AWZZ J 92LCAB4782CASY J ———— AB AP — PCUSG0022AWZZ GCAB-1223AWSA GCOVA1456AWSA GCOVA1457AWSA GCOVA1458AWSA GITAR1123AWSA GITAR1124AWSA JKNBK0093AWSA KMECB0031AWZZ 92LF513-891 92LF525-345 92LF567-716 92LF522-063 92LFF19U-31 92LF514-133 92LF514-134 92LFF19S-31 LANGK0111AWFW 92LFAN4751ASY1 LANGK0316AWFW NFANP0001AWZZ RMOTV0027AWZZ 92LCSPR1431C LBSHC0005AWZZ LCHSM0164AWFW LCHSZ0022AWZZ LHLDZ1439AWZZ MLOKC0004AWZZ MSPRD0110AWFJ PCUSG0022AWZZ PRDAR0255AWFW 92LRDAT1468B QACCD0022AWZZ QCNWN1844AWZZ QFSHD0001AWZZ QLUGP0001AWZZ 92LCSPR1431C 92LNBAND1318A LX-BZ2222AXZZ LX-HZ0009AWFD LX-JZ0010AFFD LX-JZ0036AWFD LX-JZ0037AWFD XBBSD20P04000 XEBSD26P10000 XEBSD30P10000 XEBSD30P12000 XESSD30P10000 XHBSD26P04000 XHBSD40P08000 XJBSD30P06000 XJBSD30P10000 XJBSF30P10000 XJSSD30P10000 XEBSD30P08000 AB AS AH AH AH AM 203- 2 204 205 206 207 208 208 209 210 210- 1 210- 2 210- 3 210- 4 210- 5 210- 6 210- 7 210- 8 211 212 212- 1 212- 2 212- 3(M971) 212- 4 1 213 214 215 216 217 218 221 222 225 1 226 227 1 228 229 231 232 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 618 –5– J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J AK BD BG BE AZ AZ AL AL AL AL AE AQ AE AD AM AA AD AP AN AE AD AB AB AV AE AM AC AB AC AA AA AB AC AA AB AB AA AA AA AA AA AA AA AA AA AA AA AA DESCRIPTION Panel,Cassette Cover Holder,Cassette Badge,SHARP Panel,FL Display Window,Cassette Decoration Panel Button,Function Button,ON/STAND-BY Button,Disc Select Button,Play/Stop Button,X-Bass Spacer,Button Damper Spring,Cassette Lead Wire with Lug Side Panel Ass’y ,Left Side Panel Ass’y,Left (Not Replacement Item) Cushion,Leg Side Panel Ass’y ,Right Side Panel Ass’y,Right (Not Replacement Item) Cushion,Leg Cabinet,Top CD 1 Tray Cover CD 2 Tray Cover CD 3 Tray Cover Rear Panel [Except for Canada] Rear Panel [For Canada] Knob,VOLUME Tape Mechanism Ass’y Head Plate Block Motor with Pulley Tape Mechanism PWB Ass’y Clutch Ass’y Block Belt,Main Pinch Roller Block,Right Pinch Roller Block,Left Belt,FF/REW Bracket,Cassette Lock Lever Fan Motor Ass’y Bracket,Fan Motor Rotary,Fan Motor,Air Cooling Fan Spring,Ring Bushing,AC Power Supply Cord Chassis,Main Chassis,Changer Unit Holder,FL Display Lock Lever,Cassette Spring,Cassette Lock Lever Cushion,Leg Heat Sink,Main Heat Sink,Sub AC Power Supply Cord Lead Wire with Lug Holder,Fuse Lug (LUG902,903) Spring,Ring Nylon Band,80mm Screw,Special Screw,Special Screw,ø3×10mm Screw,Special Screw,ø3×12mm Screw,ø2×4mm Screw,ø2.6×10mm Screw,ø3×10mm Screw,ø3×12mm Screw,ø3×10mm Screw,ø2.6×4mm Screw,ø4×8mm Screw,ø3×6mm Screw,ø3×10mm Screw,ø3×10mm Screw,ø3×10mm Screw,ø3×8mm XL-HP500 NO. PRICE RANK PART CODE DESCRIPTION SPEAKER BOX PARTS 901 901- 1 GBOXS0112AWSA J ———— 901- 2 901- 3 901- 4 901- 5 901- 6 902 902- 1 QCNWN2421AWZZ PCUSG0138AWZZ QTANA9010AWZZ PCOVZ1022AWSA PDUC-0015AWSA CPNLS1074AW01 ———— J J J J J J AM AC AG AL 902- 2 902- 3 903 903- 1 LHLDZ8002AWSA J XJBSD30P12000 J CWAKP1074AW01 J ———— AG AA AS — 903- 2 904 905 906 SP1,2 SP3,4 HBDGB1001AWSA TSPC-1132AWZZ XJBSD30P10000 XJBSD40P12000 RSPA00068AW6T RSPA10081AW6W AD AC AA AA AR AY J J J J J J — AV — Speaker Box Ass’y Speaker Box (Not Replacement Item) Network Cord Cushion,Foot Terminal Cover,Duct Pipe Duct Pipe Front Panel Ass’y Front Panel (Not Replacement Item) Catching Holder Screw,ø3×12mm Net Frame Ass’y Net Flame (Not Replacement Item) Badge,SHARP Label,Specification Screw,ø3×10mm Screw,ø4×12mm Tweeter Woofer PACKING PARTS (EXCEPT FOR U.S.A.) SPAKA0395AWZZ SPAKA0396AWZZ J J SPAKC1510AWZZ SPAKZ0963AWZZ SPAKZ1005AWZZ SSAKA0007AWZZ SSAKH0094AWZZ SSAKH0099AWZZ TLABN0100AWZZ TLABZ0593AWZZ TLABZ1340AWZZ J J J J J J J J J AM Packing Add.,Unit,Left/Right AL Packing,Add.,Front Speaker,Top/Bottom AU Packing Case Sheet,Speaker Sheet,Net Frame AB Polyethylene Bag,Accessories AE Polyethylene Bag,Unit AD Polyethylene Bag,Speaker AB Label,Serial No. AB Label,Energy Star AC Label,Pop PACKING PARTS (FOR CANADA) SPAKA0395AWZZ SPAKA0396AWZZ J J SPAKC1511AWZZ SPAKZ0963AWZZ SPAKZ1005AWZZ SSAKA0007AWZZ SSAKH0094AWZZ SSAKH0099AWZZ TLABN0112AWZZ TLABR1291AWZZ TLABZ0593AWZZ TLABZ1340AWZZ J J J J J J J J J J AM Packing Add.,Unit,Left/Right AL Packing,Add.,Front Speaker, Top/Bottom Packing Case Sheet,Speaker Sheet,Net Frame AB Polyethylene Bag,Accessories AE Polyethylene Bag,Unit AD Polyethylene Bag,Speaker AA Label,Serial No. AB Label,Bar Code AB Label,Energy Star AC Label,Pop ACCESSORIES QANTL0007AWZZ J QCNWN2430AWZZ J TINSE0498AWZZ J TINSK0145AWZZ TINSZ0892AWZZ RRMCG0347AWSA GFTAB1049AWSA J J J J AK AM/FM Loop Antenna AM Speaker Cord AQ Operation Manual [Except for Canada] AF Operation Manual [For Canada] AG Quick Guide [Except for Canada] AS Remote Control Battery Lid,Remote Control P.W.B. ASSEMBLY (Not Replacement Item) PWB-A1~4 1 PWB-B1,2 PWB-C PWB-D PWB-E 92LPWB4763MANS J 92LPWB4763PWRS J 92LPWB4751CDUS J QPWBF0027AWZZ J QPWBF0322AWZZ J BW BG BE AD AC Main/Display/Headphones/Jack Power/Power CD Servo CD Motor (PWB Only) Switch (PWB Only) AZ CD Optical Pickup Lens Cleaner Disc OTHER SERVICE PARTS UDSKA0004AFZZ J –6– XL-HP500 306-2 A 306 306-1 306-3 701 704 B 701 304 C 302 702 301 D 303 703x2 E M1 F 307 308 M2 305x2 G SW4 H PWB-D 1 2 3 4 Figure 7 CD MECHANISM EXPLODED VIEW –7– 5 6 XL-HP500 806 102 102 134 A 135 118 118 101 121 101 121 B 102 136 801x4 CD MECHANISM 804 111 C 106 138 805 118 110 120 101 121 133 D 806x3 107 122 131 124 122 131 132 E 117x2 802x2 103 109 125 129 802 x2 132 137 126 116x2 115 114 113 132 803 108 127 128 129x3 F 129 130 130 SWB101/102 , 804 SWB103/104 PWB-E SWB 105 112 129 128 130 129x3 104 SWB 108 SWB SWB 107 106 G 108 805 130 112 129 128 130 129x3 140 MOB1 805 139 119x3 130 112 MOB2 80mm H 1 2 3 4 Figure 8 CD CHANGER MECHANISM EXPLODED VIEW –8– 5 6 XL-HP500 609x2 BELT CONNECTION FF/REW Clutch A Main Belt Motor 608x2 CD CHANGER UNIT FF/REW Belt Flywheel Flywheel CAUTION : RING SPRING ASSY.INTO FAN POSITION. OK RING GAP 204 205 NG 206 RING GAP 609x2 207 B FAN RIB 614x13 FAN RIB CAUTION : MUST VISUAL CHECK AFTER FULLY INSERTED THE FAN TO MOTOR. 215 4.9mm ( FOR REFERENCE ONLY ) GAP IS 4.9 mm BETWEEN FAN AND FAN MOTOR BRACKET. 603x2 208 FAN BLADE FAN MOTOR BRACKET. PWB-A1 PWB-A4 C 608x2 608x3 614 PWB-C 202 225 614 202-1 615x2 614x3 229 603x2 B D 222 229 227 202-2 Silicon Grease yy ,, y yy ,, , yy ,, , y 607x9 601 Silicon Grease 605x2 PWB-A3 PWB-A2 604x3 201-13 PWB-B2 612x4 E 201-11 613x2 212-3 (M971) 201 201-2 201-1 606x2 216 607 201-10 212-4 A 201-3 201-19 201-6 201-16 212-1 201-7 FL701 F 201-12 201-14 201-17 231 PWB-B1 212-2 226 213 618 B 209 212 228x8 610x4 203-1 A 211 221 G 217 218 616x2 201-9 214 201-5 210-1 210-2 210-3 210-4 210-5 210-6 210-7 210-8 201-8 611x2 602 232 203-2 203 201-4 H 201-18 614x3 210 Note: Only the unit and consumable parts are supplied as parts supply for the Tape mechanism. 1 2 3 4 Figure 9 CABINET EXPLODED VIEW –9– 5 6 XL-HP500 A TWEETER SP1(L-CH) SP2(R-CH) B TWEETER SP1(L-CH) SP2(R-CH) Capacitor 2.2µ,100V WOOFER SP3(L-CH) SP4(R-CH) RED Capacitor 2.2µ,100V BK RED 902 BK WOOFER SP3(L-CH) SP4(R-CH) 902-3x2 901 C 902-1 902-2x2 901-2 D 901-5 902-2x2 901-6 901-1 902-3x2 E 903-2 903-1 904 903 SP1,2 905x2 F 901-4 SP3,4 906x4 G 901-3x4 H 1 2 3 4 Figure 10 SPEAKER EXPLODED VIEW – 10 – 5 6 XL-HP500 PACKING OF THE SET (FOR U.S.A. ONLY) Setting position of switches and knobs Tape Mechanism STOP UNIT Front Speaker(L/R) Polyethylene Bag,Unit SSAKH0094AWZZ Polyethylene Bag,Speaker SSAKH0099AWZZ Label,Energy Star TLABZ0593AWZZ Packing,Add., Front Speaker,Top/Bottom SPAKA0396AWZZ Packing Add.,Unit,Left/Right SPAKA0395AWZZ Label,Serial No. TLABN0100AWZZ Bottom Label,Pop TLABZ1340AWZZ A Sheet,Speaker SPAKZ0963AWZZ Sheet,Net Frame SPAKZ1005AWZZ B Polyethylene Bag,Accessories SSAKA0007AWZZ Speaker Cord AM Loop Antenna Remote Control Operation Manual Quick Guide B A Packing Case SPAKC1510AWZZ : Not Replacement Item – 11 – XL-HP500 –MEMO– XL-HP500 COPYRIGHT © 2002 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. SHARP CORPORATION AV Systems Group Audio Systems Division Higashihiroshima, Hiroshima 739-0192, Japan Printed in Japan A0211-1459SS•HA•M SC • SL • LAG