Download Sharp XG-C40XUSL Service manual
Transcript
XG-C40XU/XE SERVICE MANUAL SERVICE-ANLEITUNG S01B4XG-C40XU LCD PROJECTOR LCD PROJEKTOR MODELS MODELLE XG-C40XU/XE In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used. Im lnteresse der Benutzersicherheit (erforderliche Sicherheitsregeln in einigen Ländern) muß das Gerät in seinen Originalzustand gebracht werden. Außerdem dürfen für die spezifizierten Bauteile nur identische Teile verwendet werden. CONTENTS INHALT Page SPECIFICATIONS ...................................................... 2 INPORTANT SERVICE SAFTY NOTES(for USA) ...... 3 OPERATION MANUAL ............................................... 7 REMOVING OF MAJOR PARTS .............................. 13 RESETTING THE TOTAL LAMP TIMER .................. 18 THE OPTICAL UNIT OUTLINE ................................ 19 CONVERGENCE AND FOCUS ADJUSTMENT ........ 20 ELECTRICAL ADJUSTMENT ................................... 25 ADJUSTING THE PC BOARD ................................. 31 TROUBLE SHOOTING TABLE ................................ 32 CHASSIS LAYOUT ................................................... 92 BLOCK DIAGRAM .................................................... 94 OVERALL WIRING DIAGRAM .................................. 96 DESCRIPTION OF SCHEMATIC DIAGRAM ............. 98 WAVEFORMS ........................................................... 99 SCHEMATIC DIAGRAM ......................................... 100 PRINTED WIRING BOARD ASSEMBLIES ............ 148 PARTS LIST Ë ELECTRICAL PARTS ........................................ 158 Ë CABINET AND MECHANICAL PARTS .............. 178 Ë ACCESSORIES PARTS .................................... 184 Ë PACKING PARTS ............................................... 184 » PACKING OF THE SET .......................................... 185 » » » » » » » » » » » » » » » » » » » » » » » » » » » » » » » » » » » » » Seite TECHNISCHE DATEN ............................................. 48 HINWEISE FÜR DAS WARTUNGSPERSONAL ...... 49 BEDIENUNGSANLEITUNG ..................................... 50 ENTFERNEN DER HAUPTTEILE ............................ 56 NULLSTELLUNG DES LAMPENBETRIEBSSTUNDENZÄHLERS (GESAMTZEIT).... 61 ÜBERSICHT DER OPTIKEINHEIT .......................... 62 EINSTELLUNG VON KONVERGENZ UND BRENNPUNKT ......................................................... 63 ELEKTRISCHE EINSTELLUNG ............................... 68 EINSTELLUNG DER PC-PLATINE .......................... 74 FEHLERSUCHTABELLE .......................................... 75 CHASSIS-ANORDNUNG ......................................... 92 BLOCKSCHALTBILD ................................................ 94 GESAMTSCHALTPLAN ........................................... 96 BESCHREIBUNG DES SCHEMATISCHEN SCHALTPLANS ........................................................ 98 WELLENFORMEN ................................................... 99 SCHEMATISCHER SCHALTPLAN ........................ 100 LEITERPLATTENEINHEITEN ................................ 148 ERSATZTEILLISTE Ë ELEKTRISCHE BAUTEILE ................................ 158 Ë GEHÄUSE UND MECHANISCHE BAUTEILE ... 178 Ë ZUBEHÖRTEILE ................................................ 184 Ë VERPACKUNGSTEILE ...................................... 184 VERPACKEN DES GERÄTS .................................. 185 SHARP CORPORATION 1 XG-C40XU/XE Specifications Product type Model Video system Display method LCD panel Lens Projection lamp Contrast ratio Video input signal S-video input signal Horizontal resolution Audio output Computer RGB input signal Pixel clock Vertical frequency Horizontal frequency Computer control signal Speaker system Rated voltage Input current Rated frequency Power consumption Operating temperature Storage temperature Cabinet I/R carrier frequency Laser pointer of remote control Dimensions (approx.) Weight (approx.) Supplied accessories Replacement parts LCD Projector XG-C40XU/XE PAL/SECAM/NTSC 3.58/NTSC 4.43/DTV 480P/DTV 720P/DTV 1080I LCD panel × 3, RGB optical shutter method Panel size: 22.9 mm (0.9") (13.9 [H] × 18.5 [W] mm) Display method: Translucent TN liquid crystal panel Drive method: TFT (Thin Film Transistor) Active Matrix panel No. of dots: 786,432 dots (1,024 [H] × 768 [V]) 1–1.3 × zoom lens, F1.7–2.0, f = 33–43 mm DC 200 W lamp 250:1 RCA Connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 Ω terminated RCA Connector: AUDIO, 0.5 Vrms more than 22 kΩ (stereo) 4-pin Mini DIN connector Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated 560 TV lines (video input), 750 TV lines (DTV 720P input, Dot by Dot) 3 W (monaural) 15-PIN MINI D-SUB CONNECTOR (INPUT 1, 2): RGB separate/composite sync/sync on green type analog input: 0–0.7 Vp-p, positive, 75 Ω terminated STEREO MINIJACK: AUDIO, 0.5 Vrms, more than 22 kΩ (stereo) HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative) or composite sync (Apple only) VERTICAL SYNC. SIGNAL: Same as above 12–230 MHz 43–200 Hz 15–126 kHz 9-pin Mini DIN female connector (RS-232C Input Port) 8 cm (3 3⁄32") round AC 100–240 V 3.3 A 50/60 Hz 300 W 41°F to + 104°F (+ 5°C to + 40°C) -4°F to + 140°F (– 20°C to + 60°C) Plastic 38 kHz Wave length: 650 nm / Max. output: 1 mW / Class II Laser Product 9 1/64" (W) × 4 49/64" (H) × 12 13/64" (D) (229 × 121 × 310 mm) (main body only) 9 19/32" (W) × 5 9/32" (H) × 14 7/64" (D) (243.5 × 134 × 358.4 mm) (including adjustment feet and projecting parts) 10.6 lbs. (4.8 kg) Remote control, Two AA size batteries, Power cord (11' 10" 3.6m), Computer RGB cable (9' 10" 3 m), Computer audio cable (9' 10" 3 m), USB mouse control cable (3' 3" 1 m), DIN-D-sub RS-232C cable (6 45/64" 15 cm), Remote mouse receiver, Extra air filter, Lens cap (attached), CD-ROM, LCD projector operation manual, LCD projector quick references, Sharp Advanced Presentation Software operation manual Lamp unit (Lamp/cage module) (BQC-XGC40XU/1), Remote control (RRMCG1579CESA), (RRMCG1584CESA),AA size batteries, Power cord (QACCU5013CEZZ(XG-C40XU), QACCB5024CENA(XG-C40XE),QACCV4002CEZZ(XG-C40XE)), Computer RGB cable (QCNWG0002CEZZ), Computer audio cable (QCNW-4870CEZZ), USB mouse control cable (QCNWG0007CEPZ), DIN-D-sub RS-232C cable (QCNW-5288CEZZ), Remote mouse receiver (RUNTK0673CEZZ), Air filter (PFILD0076CEZZ), Lens cap (GCOVH1307CESB), CD-ROM (UDSKA0053CEN1),(UDSKA0057CEN1), LCD projector operation manual (TINS-7482CEZZ),(TINS-7533CEZZ), LCD projector quick references (TINS-7483CEZZ), (TINS-7534CEZZ, TINS-7535CEZZ, TINS-7536CEZZ), Sharp Advanced Presentation Software operation manual (TINS-7538CEZZ),(TINS-7537CEZZ) This SHARP projector uses LCD (Liquid Crystal Display) panels. These This unit has some inactive TFTs within acceptable tolerances which very sophisticated panels contain 786,432 pixels ( × RGB) TFTs (Thin may result in illuminated or inactive dots on the picture screen. This Film Transistors). As with any high technology electronic equipment will not affect the picture quality or the life expectancy of the unit. such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to. Specifications are subject to change without notice. 2 XG-C40XU/XE INPORTANT SERVICE SAFETY NOTES (for USA) Ë Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and servicing guidelines as follows: » Use an AC voltmeter with sensitivity of 5000 ohm per volt., or higher, sensitivity to measure the AC voltage drop across the resistor (See Diagram). » All checks must be repeated with the AC plug connection reversed. (If necessary, a non-polarized adapter plug must be used only for the purpose of completing these checks.) Any reading of 0.3 volts RMS (this corresponds to 0.2 milliamp. AC.) or more is excessive and indicates a potential shock hazard which must be corrected before returning the unit to the owner. WARNING 1. For continued safety, no modification of any circuit should be attempted. 2. Disconnect AC power before servicing. BEFORE RETURNING THE PROJECTOR: (Fire & Shock Hazard) Before returning the projector to the user, perform the following safety checks: 1. Inspect lead wires are not pinched between the chassis and other metal parts of the projector. 2. Inspect all protective devices such as non-metallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacity networks, mechanical insulators, etc. 3. To be sure that no shock hazard exists, check for current leakage in the following manner: » Plug the AC cord directly into a 120-volt AC outlet, (Do not use an isolation transformer for this test). » Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in parallel between all exposed metal cabinet parts and earth ground. AC VOLTMETER 1.5k ohm (10W) 0.15µF TEST PROBE TO EXPOSED METAL PARTS CONNECT TO KNOWN EARTH GROUND 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 SAFETY NOTICE AVIS POUR LA SECURITE Many electrical and mechanical parts in DLP Projector have special safety-related characteristics. These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily increased by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this manual; electrical components having such features are identified by “å” and shaded areas in the Replacement Parts Lists and Schematic Diagrams. For continued protection, replacement parts must be identical to those used in the original circuit. The use of a substitute replacement parts which do not have the same safety characteristics as the factory recommended replacement parts shown in this service manual, may create shock, fire or other hazards. De nombreuses pièces, électriques et mécaniques, dans les projecteur à DLP présentent des caractéristiques spéciales relatives à la sécurité, qui ne sont souvent pas évidentes à vue. Le degré de protection ne peut pas être nécessairement augmentée en utilisant des pièces de remplacement étalonnées pour haute tension, puissance, etc. Les pièces de remplacement qui présentent ces caractéristiques sont identifiées dans ce manuel; les pièces électriques qui présentent ces particularités sont identifiées par la marque “å” et hachurées dans la liste des pièces de remplacement et les diagrammes schématiques. Pour assurer la protection, ces pièces doivent être identiques à celles utilisées dans le circuit d’origine. L’utilisation de pièces qui n’ont pas les mêmes caractéristiques que les pièces recommandées par l’usine, indiquées dans ce manuel, peut provoquer des électrocutions, incendies ou autres accidents. WARNING: The bimetallic component has the primary conductive side exposed. Be very careful in handling this component when the power is on. AVERTISSEMENT: La composante bimétallique dispose du conducteur primaire dénudé. Faire attention lors de la manipulation de cette composante sous tension. 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 3 XG-C40XU/XE NOTE TO SERVICE PERSONNEL 12345678901234567890123456789012123456789012345 NOTE POUR LE PERSONNEL D’ENTRETIEN 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 UV-RADIATION PRECAUTION 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 PRECAUTION POUR LES RADIATIONS UV 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 The light source, metal halide lamp, in the LCD projector emits small amounts of UV-Radiation. La source de lumière, la lampe mètal halide , dans le projecteur LCD émet de petites quantités de radiation UV. AVOID DIRECT EYE AND SKIN EXPOSURE. EVITEZ TOUTE EXPOSITION DIRECTE DES YEUX ET DE LA PEAU. To ensure safety please adhere to the following: Pour votre sécurité, nous vous prions de respecter les points suivants: 1. Be sure to wear sun-glasses when servicing the projector with the lamp turned “on” and the top enclosure removed. 1. Toujours porter des lunettes de soleil lors d’un entretien du projecteur avec la lampe allumée et le haut du coffret retiré. 2. Do not operate the lamp outside of the lamp housing. 2. Ne pas faire fonctionner la lampe à l’extérieur du boîtier de lampe. 3. Do not operate for more than 2 hours with the enclosure removed. 3. Ne pas faire fonctionner plus de 2 heures avec le coffret retiré. UV-Radiation and Medium Pressure Lamp Precautions Précautions pour les radiations UV et la lampe moyenne pression 1. Be sure to disconnect the AC plug when replacing the lamp. 2. Allow one hour for the unit to cool down before servicing. 3. Replace only with same type lamp. Type CLMPF0075CE01 or BQC-XGC40XU/1 rated 85V/ 200W. 4. The lamp emits small amounts of UV-Radiation, avoid direct-eye contact. 5. The medium pressure lamp involves a risk of explosion. Be sure to follow installation instructions described below and handle the lamp with care. 1. Toujours débrancher la fiche AC lors du remplacement de la lampe. 2. Laisser l’unité refroidir pendant une heure avant de procéder à l’entretien. 3. Ne remplacer qu’avec une lampe du même type. Type CLMPF0075CE01 or BQC-XGC40XU/1, caractéristique 85V/200W. 4. La lampe émet de petites quantités de radiation UVéviter tout contact direct avec les yeux. 5. La lampe moyenne pression implique un risque d’explosion. Toujours suivre les instructions d’installation décrites ci-dessous et manipuler la lampe avec soin. 4 XG-C40XU/XE 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 1234567890123456789012345678901212345678901234 UV-RADIATION PRECAUTION (Continued) 1234567890123456789012345678901212345678901234 1234567890123456789012345678901212345678901234 12345678901234567890123456789012123456789012345 PRECAUTION POUR LES RADIATIONS UV (Suite) 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 Lamp Replacement Remplacement de la lampe Note: Remarque: Since the lamp reaches a very high temperature during units operation replacement of the lamp should be done at least one hour after the power has been turned off. (to allow the lamp to cool off.) Installing the new lamp, make sure not to touch the lamp (bulb) replace the lamp by holding its reflector 2. [Use original replacement only.] Comme la lampe devient très chaude pendant le fonctionnement de l’unité, son remplacement ne doit être effectué au moins une heure après avoir coupé l’alimentation (pour permettre à la lampe de refroidir). En installant la nouvelle lampe, s’assurer de ne pas toucher la lampe (ampoule). Remplacer la lampe en tenant son réflecteur 2. [N’utiliser qu’un remplacement d’origine.] 1 Lamp 1 Lamp 2 Reflector 2 Reflector DANGER ! –– Never turn the power on without the lamp to avoid electric-shock or damage of the devices since the stabilizer generates high voltages at its start. DANGER ! –– Ne jamais mettre sous tension sans la lampe pour éviter un choc électrique ou des dommages des appareils car le stabilisateur génère de hautes tensions à sa mise en route. Since small amounts of UV-Radiation are emitted from an opening between the duct cover and the lamp housing, it is recommended to place the LENS CAP on the opening during servicing to avoid eye and skin exposure (Fig. 1). Comme de petites quantités de radiation UV sont émises par une ouverture entre le couvercle du conduit et le botier de la lampe,il est recommandé de placer le CAPUCHON D'OPTIQUE sur l'ouverture pendant l'entretien pour éviter une exposition des yeux et la peau (Fig. 1). Note: Please obtain a lens cap before servicing a model XG-C40XU that is received without one. Remarque: Priére de se procurer un capuchon d'optique acant d'entretien un modéle XG-C40XU qui est livré sans. LENS CAP LENS CAP SH AR P SH AR P Figure 1. Figure 1. 5 XG-C40XU/XE WARNING: High brightness light source, do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly in to the beam of light. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO MOISTURE OR WET LOCATIONS. CAUTION The lighting flash with arrowhead within a triangle is intended to tell the user that parts inside the product are risk of electric shock to persons. RISK OF ELECTRIC SHOCK. DO NOT REMOVE SCREWS EXCEPT SPECIFIED USER SERVICE SCREW CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE CABINET. NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are in the manual with the projector. CAUTION (INLET Unit) 5A 250V For continued protection against a risk of fire, replace only with same type 5A 250V fuse. (F761) 123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123 123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123 AVERTISSEMENT: Source lumineuse de grande intensité. Ne pas fixer le faisceau lumineux ou le regarder directement. Veiller particulièrement à éviter que les enfants ne fixent directement le faisceau lumineux. AVERTISSEMENT: AFIN D’EVITER TOUT RISQUE D’INCENDIE OU D’ELECTROCUTION, NE PAS PLACER CET APPAREIL DANS UN ENDROIT HUMIDE OU MOUILLE. ATTENTION L’éclair terminé d’une flèche à l’intérieur d’un triangle indique à l’utilisateur que les pi‘eces se trouvant dans l’appareil sont susceptibles de provoquer une décharge électrique. RISQUE D’ELECTROCUTION NE PASRETIRER LES VIS, A L’EXCEPTION DES VIS DE REPARATION UTILISATEUR SPECIFIEES Le point d’exclamation à l’intérieur d’un triangle indique à l’utilisateur que les instructions de fonctionnement et d’entretien sont détaillées dans les documents fournis avec le projecteur. ATTENTION: POUR EVITER TOUT RISQUE D’ELECTROCUTION, NE PAS RETIRER LE CAPOT. AUCUNE DES PIECES INTERIEURES N’EST REPARABLE PAR L’UTILISATEUR, A L’EXCEPTION DE L’UNITE DE LAMPE. POUR TOUTE REPARATION, S’ADRESSER A UN TECHNICIEN D’ENTRETIEN QUALIFIE. PRECAUTION (Unite d’admission) 5A 250V Pour une protection continue contre les risques d’incendie, ne remplacer qu’avec un fusible 5A 250V du même type. (F761) 6 XG-C40XU/XE OPERATION MANUAL Location of Controls Projector MUTE button LAMP REPLACEMENT indicator TEMPERATURE WARNING indicator POWER indicator VOLUME buttons (+ / – ) POWER buttons (ON/OFF) KEYSTONE button MENU button AUTO SYNC button INPUT button FREEZE button RESIZE button ENLARGE button GAMMA button BLACK SCREEN button UNDO button ADJUSTMENT buttons ('/"/\/|) ENTER button Zoom knob Carrying handle Remote control sensor Kensington Security Standard connector Focus knob Foot release Front and Top View Speaker Side and RearView Air filter/Cooling fan (Intake vent) Cooling fan (Exhaust vent) Remote control sensor INPUT 1 port (HD 15) INPUT 2 port (HD 15) AUDIO OUTPUT terminal (3.5mm stereo minijack) RS-232C port (9-pin Mini DIN) AUDIO INPUT terminal for INPUT 1, 2 (3.5 mm stereo minijack) OUTPUT port for INPUT 1, 2 (HD 15) S-VIDEO INPUT 4 terminal (4-pin Mini DIN) AUDIO INPUT 3 terminals (RCA) VIDEO INPUT 3 terminal (RCA) AC socket 7 XG-C40XU/XE Operating the Wireless Mouse Remote Control Remote Control Front View Rear View MUTE button POWER buttons (ON/OFF) VOLUME buttons (+/–) KEYSTONE/BLACK SCREEN button LEFT-CLICK button LASER POINTER/ MENU button MOUSE/ ADJUSTMENT buttons ('/"/\/|) RIGHT-CLICK/ ENTER button UNDO button INPUT button AUTO SYNC button FREEZE button ENLARGE button RESIZE button TOOLS button GAMMA button MOUSE/ ADJUSTMENT switch BACKLIGHT button Top View Remote control signal transmitter Laser pointer window Inserting the batteries in on the arrow 1 Press mark and slide in the direction of the arrow to remove the battery cover. Battery cover 2 Insert two AA size batteries, making sure their polarities match the + and – marks inside the battery compartment. the side tabs of 3 Insert the battery cover into their slots and press the cover in until it is properly seated. Battery cover Battery compartment 8 XG-C40XU/XE Using the Remote Control as a Wireless Mouse The remote control has the following three functions: • Projector control • Wireless mouse • Laser pointer MOUSE/ADJUSTMENT switch (Remote control) MOUSE ADJ. MOUSE Wireless mouse Laser pointer ADJ. Projector control Remote Control/Mouse Receiver Positioning • The remote control can be used to control the projector within the ranges shown below. • The remote mouse receiver can be used with the remote control to control the mouse functions of a connected computer within the ranges shown below. • The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may differ due to the screen material. Controlling the Projector Using the Wireless Mouse Remote control Remote control 7m 30˚ 30˚ 30˚ 45˚ 30˚ 4m 45˚ 30˚ Remote control 9 120˚ Remote mouse receiver XG-C40XU/XE Effective buttons in MOUSE mode Use as a Wireless Mouse Be sure the supplied remote mouse receiver is connected to your computer. Remote control (Front view) LASER POINTER (Slide the MOUSE/ADJUSTMENT switch on the remote control to the MOUSE position.) MOUSE ADJ. BLACK SCREEN MOUSE RIGHT-CLICK BACKLIGHT • The wireless mouse may not operate correctly if your computer serial port is not correctly set up. Refer to the computer’s operation manual for details of setting up/ installing the mouse driver. • For one-button mouse systems, use either the LEFT-CLICK or RIGHT-CLICK button. Using the remote control in a dark room Press BACKLIGHT, and the buttons will light up. Green lights refer to mouse operations, and red lights to projector adjustments. Button name Remote control (Rear view) LEFT-CLICK Position of MOUSE/ADJUSTMENT switch ADJ. MOUSE LASER POINTER/MENU LASER POINTER (GREEN) MENU (RED) BLACK SCREEN/KEYSTONE BLACK SCREEN (GREEN) KEYSTONE(RED) RIGHT-CLICK/ENTER RIGHT-CLICK (GREEN) ENTER (RED) MOUSE/ADJUSTMENT MOUSE (NOT LIT) ON (NOT LIT) LEFT-CLICK POWER ON/OFF ADJUSTMENT (NOT LIT) — VOLUME + / – MUTE INPUT UNDO FREEZE ON (RED) AUTO SYNC ENLARGE RESIZE TOOLS GAMMA Use as a Laser Pointer (Slide the MOUSE/ADJUSTMENT switch on the remote control to the MOUSE position.) MOUSE ADJ. Press LASER POINTER ( ) to activate the laser pointer. When the button is released, the light automatically goes off. • For safety, the laser pointer automatically goes off after 1 minute of continuous use. To turn it on, release LASER POINTER ( ) and press again. 10 XG-C40XU/XE Connection Pin Assignments Analog Computer 1 and 2 Signal Input Ports: 15-pin mini D-sub female connector 1 6 11 5 10 15 Computer Input Analog 1. Video input (red) 2. Video input (green/sync on green) 3. Video input (blue) 4. Reserve input 1 5. Composite sync 6. Earth (red) 7. Earth (green/sync on green) 8. Earth (blue) 9. 10. 11. 12. 13. 14. 15. Component Input 1. PR (CR) 2. Y 3. PB 4. Not connected 5. Not connected 6. Earth (PR) 7. Earth (Y) 8. Earth (PB) 9. Not connected 10. Not connected 11. Not connected 12. Not connected 13. Not connected 14. Not connected 15. Not connected Not connected GND GND Bi-directional data Horizontal sync signal Vertical sync signal Data clock RS-232C Port: 9-pin D-sub male connector of the DIN-D-sub RS-232C cable Pin No. 1 2 3 4 5 6 7 8 9 5 1 9 6 Signal CD RD SD ER SG DR RS CS CI Name I/O Receive Data Send Data Input Output Signal Ground Data Set Ready Request to Send Clear to Send Output Output Input Reference Not connected Connected to internal circuit Connected to internal circuit Not connected Connected to internal circuit Not connected Connected to internal circuit Connected to internal circuit Not connected RS-232C Terminal: 9-pin Mini DIN female connector 8 7 9 3 6 5 4 2 1 Pin No. 1 2 3 4 Signal VCC RD SD EXIR 5 6 SG ERX 7 8 9 RS CS ETX Name I/O + 3.3V (Reserved) Output Receive Data Input Send Data Output Detector of Option Unit Input (Reserved) Signal Ground IR Receive Signal from Input IR Amplifier (Reserved) Request to Send Output Clear to Send Input IR Transmit Signal Output (Reserved) 11 Reference Not connected Connected to internal circuit Connected to internal circuit Not connected Connected to internal circuit Not connected Connected to internal circuit Connected to internal circuit Not connected XG-C40XU/XE Rear Vie Dimensions 25 64 23 /64 (9) 3 51/64 (96.5) 23 64 105/16 (262) 147/64 (358.4) 5 19/32 (142) 1213/64 (310) 2 13/32 (61) / (9) 2 13 /32 (61) 5433/64 (138.5) 9 11/32 (237.5) 49 1/64 (124.5) 1 5/16 (33.5) / (10) 29/32 (23) 3 53/64 (97.5) 1 5/64 (27.5) Top View w / (16) 63 1 11/16 (43) 2 /64 (76) 13 / (25) 7 16 / (11) Front View / (13) 449/64 (121) /32 (10.5) 17 32 113/16 (30) 3 21/32 (93) 3 17/64 (83) 9 1/64 (229) 63 64 3 17/64 (83) 58 919/32 (243.5) 5 9/32 (134) Side View BottomView Units: inches (mm) 12 XG-C40XU/XE REMOVING OF MAJOR PARTS 1. Removing the Intake cover and lamp unit S A H P R 1-1. Detach the Intake cover. 1-2. Loosen the lamp cover screw and draw out the lamp cover in the direction of arrow (toward yourself). 1-3. Remove the two lamp unit lock screws. Detach the lamp unit. Lamp unit 1-3 1-3 1-2 Intake cover 1-1 Lamp cover Note: When replacing the lamp, make sure that there is a clearance of over 8mm between the terminal and the lamp snap-on spring (and other metallic parts). 13 XG-C40XU/XE 2. Removing the top and rear cabinets 2-1. Remove the four rear cabinet lock screws. 2-2. Remove the four terminal board lock screws off the rear cabinet. Unhook and detach the rear cabinet from below. 2-3. Remove the four top cabinet lock screws from below. H S R A P Press both sides of the bottom cabinet in the directions of arrow to undo the hooks. Lift and detach the top cabinet. 2-1 2-3 Hook 2-2 2-4. Slowly lift the top cabinet and disconnect the operation key unit connector (KY). Then take away the top cabinet. Top cabinet (KY) 2-4 Rear cabinet 14 XG-C40XU/XE 3. Removing the PWB units 3-1. Disconnect the connectors from the output unit. 3-2. Remove the four PC I/F unit lock screws. Remove the two screws and the earth shield, and take out the PC I/F unit. 3-3. Remove the spacer (stud bolt) and the three screws off the output unit. Lift the output unit, together with the signal unit, off the position. 3-4. Remove the S-out/REG unit angle lock screw and take out the S-out/REG unit. 3-2 PC I/F Unit (TP) (L) 3-3 3-3 3-1 3-3 (FN) (Q) (EB) Spacer (stud bolt) Output Unit 3-4 (FP)(FS) (SO) S-out/REG Unit Angle 3-2 (F) Signal Unit (EB) 3-1 PC Terminal Unit (EA) (SP) (SO) S-out/REG Unit Video Unit 15 XG-C40XU/XE 4. Removing the optical mechanism unit 4-1. Remove the six optical mechanism unit lock screws. Lift the unit off the position. 4-2. Remove the two lamp socket holder lock screws and take out the holder. 4-1 Duct Fan Unit 4-2 Optical Mechanism Unit 16 XG-C40XU/XE 5. Removing the Power/Ballast unit assembly 5-1. Remove the Power/Ballast unit assembly lock screw. 5-2. Remove the (FG) lead lock screw. 5-3. Lift the Power/Ballast unit assembly off the position. 6. Removing the ballast unit and inlet unit 6-1. Disconnect the connector (PA) from the inlet unit. Take out the AC power switch. 6-2. Remove the Inlet unit lock screw. 6-3. Pull the inlet unit toward yourself off the position. Note: Before installing the lamp cover, make sure the AC power switch is at the " " (OFF) position. 5-1 5-2 Power/Ballast Unit Ass'y (FG) (TP) 5-3 AC power switch (for Lamp replacement) (BA) (PA) 6-1 (FG) 6-2 (PA) 6-3 Inlet Unit 17 XG-C40XU/XE RESETTING THE TOTAL LAMP TIMER When the lamp has been replaced, reset the total lamp timer in the following steps. Resetting procedure 1. While holding down the “ENTER”, “ADJ."” and “ADJ.|” keys on the set at the same time, turn on the main power switch (located side the AC inlet). 2. Now the total lamp timer is reset to zero. “000H” appears on the screen. LAMP POWER ON I TEMP. + MUTE VOLUME OFF MENU KEYSTONE AUTO SYNC INPUT ' BLACK SCREEN ' ' ENLARGE ' FREEZE RESIZE GAMMA ENTER UNDO B ENTER ADJ." ADJ.| Lamp The lamp in this projector operates for approximately 2,000 cumulative hours, depending on the usage environment. It is recommended that the lamp be replaced after 1,900 cumulative hours of use or when you notice a significant deterioration of the picture and colour quality. The lamp usage time can be checked with the On-screen Display. CAUTION • Intense light hazard. Do not attempt to look into the aperture and lens while the projector is operating. • As the usage environment can vary significantly, the projector lamp may not operate for 2,000 hours. Condition The LAMP REPLACEMENT indicator lights up red, and “LAMP” and “ ” will flash in yellow in the lower-left corner of the picture. Problem • Lamp has been used for over 1,900 hours. A significant deterioration of the picture and colour quality occurs. The power will automatically turn off and the projector will enter standby mode. • Lamp has been used for over 2,000 hours. “LAMP” and “ ” will flash in red in the lower-left corner of the picture, and the power will turn off. 18 Possible Solution • Purchase a replacement lamp unit (lamp/cage module) of the current type BQC-XGC40XU/1 from your nearest Sharp Authorised LCD Projector Dealer or Service Centre. • Replace the lamp. If you wish, you may have the lamp replaced at your nearest Sharp Authorised LCD Projector Dealer or Service Centre. XG-C40XU/XE THE OPTICAL UNIT OUTLINE Layout of the optical system Note: Layout for positioning the optical system. Projection Lens Incident polarizing plate B AR coating emergent polarizing plate R Dichroic coating (R transmission) R-LCD emergent polarizing plate B B-LCD Cross dichroic prism ct fle -re or B ct re BLUE fle Dichroic coating (B reflection) M5 R or M4/M6 CL2 RL3 UV-filter(0.8t) Condenser lens R Relay lens 3 Porarizing film emergent polarizing plate G G-LCD Relay lens 2 Dichroic coating (B reflection) RL2 Dichroic coating (G transmission) Dichroic coating (R reflection) Porarizing film CL3 Condenser lens G GREEN Marking (Bottom) RED M2 G re fle ct M3 or Relay lens 1 ct or RL1 fle Dichroic coating UV-IR coating Marking CL1 or W PBS(polarization beam splitter) m irr DC lamp (Light source) te d Ag-deposited face -c Ag or ct fle re re B G BLUE B/ M4/M6 oa UV-filter Fly-eye lens (outgoing light) Fly-eye aperture Fly-eye lens (incoming light) 19 M1 XG-C40XU/XE CONVERGENCE AND FOCUS ADJUSTMENT » Start the convergence and focus adjustments with the top panel removed but the power on. Use the remote control to adjust the image. Take the following procedures. 1. Focusing the projection lens (A) Replacing all the 3 LCD panels 1. Before replacing all the 3 LCD panels, project an image on the screen and bring it into focus. 2. Replace the LCD panels with new ones. But until the focus has been completely readjusted, be careful not to change the projection distance between the set and the screen, nor to move the projection lens focus and zoom rings. Note: If the focus is readjusted with a different positional relation, the relation between the projection distance and the screen size is affected. In other words, a short-distance image (40 WIDE for example) may get out of the focus range, or a long-distance image (300 WIDE for example) may come out of the focus. (B) Replacing 1 or 2 of the 3 LCD panels 1. In adjusting the focus after replacement of one or two LCD panels, project an image on the screen and turn the projection lens focus ring to get the non-replaced LCD panel into focus. 2. But until the focus has been completely adjusted for the new LCD panels, be careful not to change the projection distance between the set and the screen, nor to move the projection lens focus and zoom rings. 3. If the projection distance has been changed or the projection lens readjusted, repeat the above steps 1 and 2. 2. Focus adjustment (A) Adjusting the G-LCD panel(Make this adjustment on the white-only screen.) 1. Adjustment in θX and Z directions . Loosen the lock screw "a" and insert an eccentric screwdriver into the notch and hole "a". Turn the screwdriver until the top, center and bottom on the screen get into focus. In adjusting this top-to-bottom focus, tighten the lock screws "b" and "c" to fix the θY direction adjustment. First get the right and left halves in balance. Then improve the accuracy while making the adjustment 2 below. 2. Adjustment in θY direction Temporarily tighten the lock screw "a" and loosen the lock screws "b" and "c". Insert the eccentric screwdriver into the notch and hole "c" for adjusting in the θY direction on the top of the screen. Insert the eccentric screwdriver into the notch and hole "b" for adjusting in the θY direction on the bottom of the screen. 3. Repeat the above steps 1 and 2 to finely adjust the focus. Finally tighten up all the lock screws. Notes : 1 Carefully proceed with the focus adjustment because the adjusting directions are correlated. 2 In adjusting the convergence and focus, do not move the projection lens zoom and focus rings until the end of all the adjustments. (B) Adjusting the B-LCD panel (Do the same for the R-LCD panel.) 1. Take the same procedure as for the G-LCD panel focus adjustment. Note that the adjustment range is wider in the Z direction. If the convergence is quite different between the B-LCD and G-LCD panels, roughly adjust the convergence first and then the focus. 3. Convergence adjustment » Use a crosshatch pattern signal for this adjustment. Make the adjustment just for the G-LCD and the relevant colour. 1. Loosen the convergence lock screw "d". 2. Adjustment in Y and θZ directions Put a hex wrench in the Y and θZ direction adjustment zone. 3. Adjustment in X direction Put an eccentric cam adjusting wrench in the X direction adjustment zone. 20 XG-C40XU/XE 4. With the G-LCD panel's screen center as refernce, adjust the R-LCD and B-LCD panels. 5. Finally tighten up the convergence lock screw "d". Notes : 1 The eccentric cam is used for convergence adjustment. This means that the cam's turning and the linear movement are not always uniform. 2 This model is not equipped with the LCD image adjustment mechanism. This is because the cross-dichroic prism is used for image formation. When the LCD panels all get into best focus, the images are almost completely converged. Convergence and Focus Adjustments Mechanism TOP VIEW SIDE VIEW Lock screw "a" R-LCD Notch and hole "c" G-LCD panel mounting screws (four screws) G-LCD Lock screw "c" G-LCD Lock screw "b" Notch and hole "b" Lock screw "c" Notch and hole "c" B-LCD Notch and hole "a" SIDE VIEW (from outside) SIDE VIEW (from inside) Eccentric cam (Y direction adjustment) Lock screw "d" Lock screw "d" R·B-LCD panel mounting screws (four screws) R·B-LCD 21 Eccentric cam (X direction adjustment) Eccentric cam (θZ direction adjustment) XG-C40XU/XE Convergence and Focus Adjustments at a Glance Adjustment directions Adjustment Direction X direction Convergence Y direction θZ direction Z direction Focus θX direction θY direction Definition Direction of LCD panel LCD right and left LCD top and bottom LCD turning axis LCD optical axis LCD top-to-bottom flapping LCD right-to-left flapping Rotation around Z axis Rotation around X axis Rotation around Y axis Convergence and Focus Adjustment for the Optical Mechanism Colour Adjustment Direction Movement Position Adjusting tool Lock screw Tightening tool X direction ±0.8mm Eccentric cam Eccentric cam adjusting wrench d Hex wrench Y direction ±0.8mm Eccentric cam Eccentric cam adjusting wrench d Hex wrench R/B θZ direction ±1° Eccentric cam adjusting wrench d Hex wrench colours Z direction ±0.8mm Notch and hole "a" & "c" Eccentric screwdriver, a, c θX direction ±1° Notch and hole "a" & "c" a, c θY direction ±1° Notch and hole "b" & "c" Phillips screwdriver, *Hex wrench Z direction ±0.2mm θX direction ±1° θY direction ±1° Convergence Focus G colour Focus Eccentric cam Bladed screwdriver b, c Same as for R and B colours Focus Adjustments the Other Way Lock screw Position a Notch and hole "a" b Notch and hole "b" c Notch and hole "c" Related direction Z and θX directions θY direction Z, θX and θY directions Convergence and Focus Adjusting and Tightening Tools Tool Eccentric cam adjusting wrench Specific or General Specific Tool code Configuration 9DASPN-XGNV1U 80 Eccentric screwdriver Specific 9DADRiVER-NV4U R2 CUT 9EQLNC-XGNV1U 16 5 100 50 Hex wrench 2 General (redesigned) 92 5 7.5 9EQLNC-XGNV4U 2 0.5 2 General — *Hex wrench General — 22 ø5 Phillips screwdriver min85 9EQDRiVER-NV1B ø3.5 General 3.5 Bladed screwdriver For M2.6 pan-head machine screw 1.27mm, preferably use a 70 mm or longer screwdriver (with a handle). XG-C40XU/XE Replacing the LCD panels Detach the top panel and the optical mechanism unit in advance. (1) Remove the four prism holder lock screws. Detach the prism holder from the optical mechanism unit. (2) Remove the LCD panel lock screws (four each for the R-, G- and B-LCD panels). Detach the LCD panels from the prism holder. (3) Mount a new LCD panel in the reverse order of the above steps (1) and (2). ~ Readjust the convergence and focus. Note that the G-LCD panel needs no convergence adjustment and has a small adjustment range in the Z direction. 1 Prism holder Optical Mechanism Unit SIDE VIEW SIDE VIEW (from inside) Lock screw "d" G-LCD Lock screw "d" 2 R·B-LCD panel mounting screws R·B-LCD 23 2 G-LCD panel mounting screws XG-C40XU/XE Adjusting the optical axis of the mirrors (M1, M5 and M4/M6) The optical axis must be readjusted if an eclipse happens with the R. G or B mirrors. Generally speaking, this adjustment is needed when any of the internal optical components has been replaced. Adjustment procedure required when any of the panels has been replaced or the convergence has been adjusted (1) Disconnect the flat cables of all the LCD panels. (2) Let the lamp light up. (3) To adjust the G mirror, shield the R and B mirrors with shielding plates (You can use a business card or the like to block the light). (4) Loosen the lock screw of the M1 adjust lever. (5) Looking at the G image on the screen, turn or slide the M1 adjust lever until the eclipse on the screen disappears. Tighten up the screw. (6) To adjust the R mirror, shield the G and B mirrors and adjust the M5 adjust lever. For the B mirror, shield the R and G mirrors and adjust the M6 adjust lever. (Take the same steps 4 and 5 above.) (7) Remove all the shielding plates to have a white image. Make sure there is no eclipse. Shielding plate B FRONT M4/M6 adjust lever Lock screws Shielding plate R M5 adjust lever slide turn Lock screws turn slide Shielding plate G M1 adjust lever turn slide Lock screws 24 XG-C40XU/XE ELECTRICAL ADJUSTMENT Hook up a signal generator, or a DOSV or Mac personal computer to the projector in order to feed the signals specified in the Adjusting conditions. No. Adjusting point Adjusting conditions Adjusting procedure 1 EEPROM initialization 1. Turn on the power (make » Make the following settings: sure the lamp lights up) and Press SW5101 to call up the process mode and warm up the unit for 15 minexecute S2 in the SSS menu. Now the system, utes. with the PC board not included, is initialized. Do not execute S1 because otherwise the PC board will be initialized. To adjust the PC board, follow the instruction in "Adjusting the PC board". (See page 31) 2 3.3V power supply adjustment 1. Turn on the power. » Adjust R1649 so that the voltmeter should read 2. Connect the digital voltme3.43 ±0.03 Vp-p. ter to TP1446. 3 2.5V power supply adjustment 1. Turn on the power. » Adjust R1652 so that the voltmeter should read 2. Connect the digital voltme2.60 ±0.05 Vp-p. ter to TP1447. 4 R drive 1. Feed the 100% red-only sig- » Using the control switches or the remote controller nal. Make the following buttons, adjust the data so that the signal bechoice. comes bit-less (noise). Group : A/D Subject : R-D 5 B drive 1. Feed the 100% blue-only » Using the control switches or the remote controller signal. Make the following buttons, adjust the data so that the signal bechoice. comes bit-less (noise). Group : A/D Subject : B-D 6 G drive 1. Feed the 100% green-only » Using the control switches or the remote controller signal. Make the following buttons, adjust the data so that the signal becomes choice. bit-less (noise). Group : A/D Subject : G-D 7 RGB 1 system 1. Make the following choice: » Choose the subject G1-GAIN and adjust the sigblack level Group : OUTPUT 1 nal amplitude to 3.3 ±0.1 Vp-p using the control signal amplitude Subject : G1-BLK switches or the remote controller buttons. (odd-numbered) G1-GAIN » Next,choose the subject G1-BLK and adjust the For red, choose the subwhite to white level to 2.6 ±0.1V DC. jects R1-BLK and R1-GAIN. 2.6V For blue, choose the sub(Adjust to 2.6V 3.3Vp-p jects B1-BLK and B1-GAIN. DC for red and (Adjust to 3.3Vp-p blue.) 2. Connect the oscilloscope to for green and blue.) TP1101 for red. TP1201 for green TP1301 for blue » Adjust the signal's amplitude and white to white level to 3.3 ± 0.1Vp-p and 2.6 ± 0.1V DC, respectively, for red and blue. 25 XG-C40XU/XE No. 8 Adjusting point P SIGNAL Adjusting conditions Adjusting procedure 1. Connect the oscilloscope to » Adjust the PSIG waveform to the one shown below. TP1701 for red. (Adjust with PSIG-H.) TP1702 for green TP1703 for blue. PSIG 6.2±0.2V DC 2. Make the following choice: Group : OUTPUT 2 Subject : PSIG-H : PSIG-L 2.0V DC GND (Adjust with PSIG-L.) » For the green and blue colours, make sure their waveforms are similar to that of the red colour. » Make sure the pin stripe of every 12 dot doesn't appear at 10 steps signal of side nays. (Appearing white pin stripe or black one, adjust the PSIG-H.) 9 Panel ghost adjustment 1. Project the XGA60Hz ghost » ENR-PHASE adjustment (R-LCD ghost adjustment) test pattern (black charac1 Increase the setting until a ghost image (see ters in bold on the halftone Note) becomes visible at the left of the back RGB background). characters on the R half-tone background. Group: OUTPUT3 2 Lower the setting point by point until the lefthand ghost image (1 above) disappears. 2. GCK-PHASE adjustment 3 Further lower the setting by one point. Make sure the setting is fixed » ENG-PHASE adjustment (G-LCD ghost adjustat 8 (initial value). ment) Adjust the G ghost image by following the same 3. EN-WIDTH adjustment procedures described under step 1 above. Make sure the setting is fixed » ENB-PHASE adjustment (B-LCD ghost adjustat 8 (initial value). ment) Adjust the B ghost image by following the same 4. ENR-PHASE adjustment (Rprocedures described under step 1 above. LCD ghost adjustment) Note: Left-hand ghost image: Characters are shown double 12 dots left from the real characters. 5. ENG-PHASE adjustment Reference: This adjustment is made because the (G-LCD ghost adjustment) EPSON LCD panel may have 1- or 2point differences due to lot-by-lot varia6. ENB-PHASE adjustment (Btions. LCD ghost adjustment) 10 Sample-andhold pulse phase RCK-PHASE GCK-PHASE BCK-PHASE 1. Feed the XGA mode 75-Hz » Using the control switches or the remote controller black signal. buttons, make sure that the “OUTPUT 3” charac2. Make the following choice: ters are not blurry and there is no ghost image. If Group : OUTPUT 3 such blur or ghost occurs, finely adjust the setting Subject : SH-PHASE in the range of 7~9. (Have the standard level at 2.) Fix the RCK-, GCK- and BCK-PHASE settings all to 8. 26 XG-C40XU/XE No. Adjusting point Adjusting conditions Adjusting procedure 11 RGB countervoltage adjustment 1. Feed the black-and-red » Using the control switches or the remote controller (25%) stripe signal (XGA). buttons, adjust the data in order to minimize the 2. Make the following choice: flicker. Group : OUTPUT 3 Subject : RC (R) » Make the same adjustment for BC (B), GC (G), and RC-INV (B) and RC-INV (G). Group : OUTPUT 3 Subject : RC-INV (R) » See if the image is equally adjusted at the center and both sides of the screen. If not, readjust the setting to have the image equal at right and left. 12 RGB gradation regeneration adjustment 1. Feed the green-only SMPTE » Adjust the G-BLK data until the gradation of the pattern signal (XGA). portion 1 (95% and 100% white) shown below Group : OUTPUT 1 can be slightly recognized. Make sure also that the Subject : G1-BLK gradation of the portion 2 (0% and 5% black) is visible. 2 1 13 RGB white balance 1. Feed the 32-step gray scale » Choose the subjects R1-BLK and B1-BLK and signal (XGA). adjust the black balance of the gradation. Group : OUTPUT 1 Subject : R1-BLK (R) B1-BLK (B) 14 Horizontal center 1. Feed the NTSC monoscope » Using the control switches or the remote controller pattern signal. buttons, adjust the data to have the same 2. Group : VIDEO 2 overscan. Subject : N358-DLY (4) N443-DLY (0) PAL-DLY (3) SECAM-DLY (0) Make sure the settings are as above. 3. Group : VIDEO 1 Subject : NTSC-H 15 Video picture adjustment 1. Feed the split colour bar sig- » Using the control switches or the remote controller nal. buttons, adjust the black-to-white (100%) level Group : VIDEO 1 difference to 2.0 ±0.02 Vp-p. Subject : PICTURE 2. Connect the oscilloscope between pin (2) of P801 and 2.0Vp-p GND. 27 XG-C40XU/XE No. Adjusting point Adjusting conditions Adjusting procedure 16 Video brightness adjustment 1. Feed the baseband (split » Using the control switches or the remote controller colour bar) signal. (The ONbuttons, adjust the setting until the black signal AIR signal is not accepted becomes bit-less. because of its too much noise.) Group : VIDEO 2 Subject : VROS/VGOS/VBOS 2. Press the control switch or the remote control’s mute button (to set the gamma correction to the process setting). 17 Video AGC 1. Feed the split colour bar signal. » Using the control switches or the remote controller Group : VIDEO 1 buttons, adjust the setting until the white signal Subject : AGC becomes bit-less. 18 Tint 1. Feed the split colour bar signal. Group : VIDEO 1 Subject : TINT 2. Connect the oscilloscope to pin (4) of P801. » Using the control switches or the remote controller buttons, adjust the data to have the -(B-Y) waveform downhill straight. » After adjusting, adjust the value of TINT up 3 point. 19 NTSC colour saturation level 1. Feed the split colour bar sig- » Using the control switches or the remote controller nal. buttons, adjust the difference between the 100% Group : VIDEO 1 white portion and the red portion to 0.00 ±0.05 Vp-p. Subject : N-COLOR (same as 100% white) 2. Connect the oscilloscope to 100% White Red pin (1) of P801. 20 PAL colour saturation level 1. Feed the PAL colour bar sig- » Using the control switches or the remote controller nal. buttons, adjust the difference between the 100% Group : VIDEO 1 white portion and the red portion to 0.2 ±0.05 Vp-p. Subject : P-COLOR 100% White Red 2. Connect the oscilloscope to pin (1) of P801. 21 SECAM colour saturation level 1. Feed the SECAM colour bar » Using the control switches or the remote controller signal. buttons, adjust the data to have a level difference Group : VIDEO 1 of 0.2 ±0.05 Vp-p between the 100% white portion Subject : S-COLOR and the red portion. 2. Connect the oscilloscope to 100% White Red pin (1) of P801. 28 XG-C40XU/XE No. Adjusting point Adjusting conditions Adjusting procedure 22 Video input panel signal amplitude adjustment 1. Feed the NTSC 10-step sig- » Select R1-GAIN and adjust the setting so that the nal. R and G signals have the same amplitude. 2. Select the following group » For the blue colour, adjust the setting the same and subject. way. Group: VIDEO2 Subject: R1-GAIN B1-GAIN 3. Connect the oscilloscope to TP1101 (R) and TP1201 (G). 4. For the blue colour, connect the oscilloscope to TP1301 (B) and TP1201 (G). 23 Video white balance 1. Feed the NTSC monoscope » Using the control switches or the remote controller pattern signal buttons, adjust so that the entire screen looks Group : VIDEO 2 evenly colourless. Subject : R1-BLK B1-BLK 24 DTV white balance 1. Feed the monoscope pattern » Using the control switches or the remote controller buttons, adjust so that the entire screen looks signal. evenly colourless. 2. Group: DTV Subject: CR-OFFSET CB-OFFSET 25 Setup 1. Group: VIDEO1 Subject: SET UP B SET UP C 26 Automatic colour correction 1. Using the colour correction » Make sure there is no noticeable colour irregularity system (ccdc), apply autoleft on the screen. matic colour correction. 27 Colour system performance check 1. Receive the colour bar sig- » In the process mode and select L1. Check the colnal. our and tint. 28 Video system performance check 1. Receive the monoscope pat- » In the process mode and select L2. Check the pictern signal. ture, brightness and sharpness. 29 Audio system performance check » In the process mode nad select L3. Check the bass, treble. » Make sure the settings are 11 for SET UP B and 2 for SET UP C. 29 XG-C40XU/XE No. Adjusting point Adjusting conditions 30 RGB performance check 31 Off-timer performance check 32 Thermistor performance check 1. Heat the thermistor using a » Make sure the “TEMP” is displayed. dryer. 33 Automatic synchronization 1. Receive the PHASE check » Call the VGA/SVGA/XGA/SXGA mode and make pattern signal. sure that the clock, phase, horizontal and vertical positions can be automatically adjusted. 34 Keystone correction performance check » Make sure the keystone correction functions well. 35 Factory settings » Make the following settings. 1. Receive the RGB signal. Adjusting procedure » In the process mode and select L4. Check the picture, brightness, red, blue, clock, phase, horizontal position, and vertical position. » In the process mode and select OFF. Make sure that the off-timer starts with “5” (minutes), counts down each minute in 1 second, and turns off the set at “0”. Process adjustment S3 S4 30 Remote controller setting “Factory setting 3”(XG-C40XE) “Factory setting 4”(XG-C40XU) XG-C40XU/XE ADJUSTING THE PC BOARD (CPCi-0047CE15/16. PC I/F Unit) 1. RGB level adjustment 1) Connect a signal generator to the projector that is equipped with the 0047 PWB. Set the signal generator output to the XGA mode (VESA1024x768, 60Hz, 32-tone waveform). Adjust the output amplitude to 700 mVp-p at the P8404 connector. 2) Set the projector input to the RGB1 mode. 3) Using a pushbutton on the projector, call the process mode. 4) On the main menu screen, select the group “A/D”. 5) Select the subject “R-BRIGHT” in the group “A/D” and adjust the “R-BRIGHT” setting so that there should be no bits around the screen. 6) Do the same with the “G-BRIGHT” and “B-BRIGHT” settings. 7) Next select the group “R-D” and the settings of the above subjects so that there should be no bits around the screen. 8) Then select the groups “G-D” and “B-D” and make the same adjustments. Now let’s go to the DTV level adjustment. 2. DTV level adjustment 1) Set the signal generator output to the green-only mode. 2) On the main menu screen of the process mode, select the group “DTV”. 3) Select the subject “G-BRIGHT” in the group “DTV” and adjust the “G-BRIGHT” setting so that there should be no bits around the screen. 4) Do the same with the “CB-OFFSET” and “CR-OFFSET” settings. Now the 0047 PWB on the projector is adjusted for delivery. Note: There is no need to make the VIDEO input adjustments. Servicing precautions If the convergence gets out of spec in servicing the set, call the process mode and select the following group and subjects. Group: NOKO Subject: R-CNV-H, R-CNV-V G-CNV-H, G-CNV-V B-CNV-H, B-CNV-V (H and V are for horizontal and vertical adjustments, respectively.) Adjust the above settings to the range of 0 to 4. 31 XG-C40XU/XE TROUBLE SHOOTING TABLE Checking the PWB performance Video input in trouble RGB input in trouble Through-output in trouble Remote control in trouble Go to "Checking the video unit Feed test pattern signal from Through-output circuit in Go to "Checking the remote circuit". PC. trouble. control". Is specified cable connected No between PC and projector? Yes Use specified cable. Is supply voltage as specified? No Yes Power circuit in trouble. Does image appear? No Yes Check the connectors, starting from the PC input circuit. Go to "Trouble shooting table for PC I/F unit ". 32 XG-C40XU/XE TROUBLE SHOOTING TABLE (Continued) Checking the video system No Is the lamp on? Yes Go to "Lamp fails to light-up". No Is specified voltage fed to EA connectors? Yes Check the power circuit and its parts. Are there signal inputs at pins (3) and (29) of P402? No Yes Are there signals at pin (4) of IC401 and pin (4) of IC402? Are there signal outputs at pins (3) and (6) of IC816? Yes Yes No Go to "Checking IC801 (RGB signal output circuit)". Check IC816, IC806 and their peripheral circuits as well as switching circuit. Check the video unit circuit (IC6004 and its peripheral circuits). Checking the video unit circuit Is there video signal output at pin (7) of IC6001? No Yes Is there video signal input at IC6004? Check the IC6001 selector switch, terminal voltage and input circuit. No Yes Are there signal outputs at pins (6) and (8) of IC6004? Check the low-pass and buffer circuits of Q6009 thru Q6015. No Yes Check IC6004 and its peripheral circuits (bias). Check the low-pass and buffer circuits No of Q6002 thru Q6008. Is the signal as specified? Yes Check Q6002 thru Q6008 and their peripheral circuits. Go to "Checking IC801 (RGB signal output circuit)". 33 No Check the oscillation circuit of IC401 and IC402, and their peripheral circuits. XG-C40XU/XE TROUBLE SHOOTING TABLE (Continued) Checking IC801 (RGB signal output circuit) No Are there RGB output waveforms at No pins (31), (32) and (33) of IC801? Yes Go to "No colour or unusual tone", Check the data transfer and other "No Y signal" or "Out of sync". performance at pins (17) and (18) of Are there output waveforms at the emitters of Q1501, Q1502 and video IC801. No Q1503? Yes Check Q1501 thru Q1503, SC1501 and their peripheral circuits. Are there output waveforms at the No emitter of Q1505, Q1506 and Q1507? Yes Check IC1501, Q1505 thru Q1507 and their peripheral circuits. Go to "Trouble shooting table for PC I/F unit". Checking the chroma and Y signals of IC801 (RGB signal output) Are there signal inputs at pins (12) No (Y signal) and (19)(chroma signal) of P402? Go to "Checking the video unit Yes circuit". Are there output waveforms at pins (3)(chroma signal) and (6) No (Y signal)of IC816? Check the Yes IC816 switching and their peripheral circuits. If there is no signal at pins (9) and (1) of IC816, check 3-D noise reduction circuit (IC806). Are there signal inputs at pins (20) (chroma signal) and (21) (Y signal) of IC801? Yes Check IC801 and its peripheral circuits. Go to "Checking IC801 Check IC806 (3-D noise reduction circuit) and its peripheral circuits. No (RGB signal output circuit)". 34 XG-C40XU/XE TROUBLE SHOOTING TABLE (Continued) Checking IC806 (3-D noise reduction circuit) and its peripheral circuits Are there signal inputs at pins (40) (Y signal) and (45)(chroma signal) of No IC806? Yes Check the buffer circuit of Q814 thru Q816 as well as Q903 thru Q906. Are there signal outputs at pins (55) No (Y signal) and (51)(chroma signal) of IC806? Yes Check IC806, IC807 (memory) and their peripheral circuits. Are there signal outputs at the emitters of Q817 (Y signal) and Q910 No (chroma signal)? Yes Check the low-pass circuit around Q817, Q907 and Q910. Check IC816 and IC801 (RGB signal output circuit). No colour or unusual tone (NTSC, PAL) Is there chroma signal input at pin No (20) of IC801? Yes Go back to the signal processing block. Are there signal outputs at pins No (46)(R-Y) and (45)(B-Y) of IC801? Yes Check the oscillation of X801 and X802, and their peripheral circuits. Check IC803, IC814 and their peripheral circuits. 35 XG-C40XU/XE TROUBLE SHOOTING TABLE (Continued) No or unusual Y signal Is there Y signal input at pin (21) of No IC801? Yes Go back to the signal processing block. Is there Y signal output at pin (40) of No IC801? Yes Check IC801 and its peripheral circuits. Is there Y signal output at pin (17) of No IC803? Yes Check IC803 and its peripheral circuits as well as IC805 (AGC). Check IC803 and its peripheral circuits. No or unusual horizontal sync Is there horizontal sync pulse output No at pin (56) of IC801? Yes Check IC801 and its peripheral circuits. Is there horizontal sync pulse output No at pin (9) of IC603? Yes Check the pulse shaping circuit of IC602 and IC603. Check IC604 and its peripheral circuits, and go to "Trouble shooting table for PC I/F unit". No or unusual vertical sync Is there vertical sync pulse output at No pin (4) of IC801? Yes Check IC801 and its peripheral circuits. Check IC604 and its peripheral circuits, and go to "Trouble shooting table for PC I/F unit". 36 XG-C40XU/XE TROUBLE SHOOTING TABLE (Continued) Checking the output PWB unit No Are there signal inputs at SC1404, SC1405, SC1501 and No SC1502? Are voltages applied to EA If there is no signal at SC1501 If there is no signal at SC1404 and SC1502, go to the video and SC1405, go to "Trouble system block. shooting table for PC I/F unit". connectors and SC5502? Yes Are there signal outputs at pins (14) ,(16) and (18) of If there is no signal at EA connector or SC5502, go to Checking the power unitblock. No IC1401 ? Yes Check IC1401 and their peripheral circuits. Are there signal inputs at pin No (47) of IC1101, IC1201 and IC1301? Check IC1401 and their Yes peripheral circuits. Are there signal outputs at pins (17), (19), (21), (28), (30) and No (32) of IC1101, IC1201 and IC1301? Check IC1101,IC1201,IC1301 Yes and their peripheral circuits. Are there signal outputs at pins (17), (19), (21), (28), (30) and No (32) of IC1102, IC1202 and IC1302? Check IC1102,IC1202,IC1302 Yes No Are there signal inputs at SC1101, SC1201 and SC1301? If there is no signal input at Yes Yes and their peripheral circuits. No If there is no signal input at pins (1) and (31) of SC1101, pins (15) and (30) of SC1102 and SC1103, check SC1101, SC1102 and the switching circuit and SC1103, check IC1409 amplifier circuit of IC1101, Check the R, G and B panels. IC1201, IC1301, IC1102, and their peripheral circuits. IC1202, IC1302 and their peripheral circuits. Check IC1106, IC1206, IC1306, IC1408 and their peripheral circuits. 37 XG-C40XU/XE TROUBLE SHOOTING TABLE (Continued) No audio output Are there audio signal inputs at pin No (2) of IC1411? Yes Check the input, the switching circuit of IC3303 and IC3304, and their peripheral circuit,SC3001,SC1502,etc. Are there audio signal outputs at pin No (2) of P5508? Yes Check the IC1411 control voltage,and its peripheral circuits. Are there audio signal outputs at pin No (6) of IC7301? Yes Check IC7301 and its peripheral circuits. If the voltage at pin (2) of IC7301 is Check IC7301 and its peripheral not as specified, check Q5501, circuits, and the SP connectors and Q5502 and their peripheral circuits. speakers. Checkig the Power Unit There is no voltage output at EA connector. Yes Is there any other output voltage failure? No Which output voltage line fails? 6.7V Is EA connector disconnected Yes or loose? No Replace ICP751. Reconnect the EA connector. Is AC voltage (85-264V) No applied across the PA connector? Yes Replace F701 or Check Bimetal SW. Yes Is TF701 open? No Replace TF701. Is R706 open? No Yes Replace R700. Replace Power unit. 38 XG-C40XU/XE TROUBLE SHOOTING TABLE (Continued) Power on Is the right input selected? No Yes Select the right input with remote control. Are the PC, video and LCP cables as No specified and properly connected? Yes Use the right cables or reconnect the cables. With the contrast control at maximum, Yes does the image appear? No Readjust the video system. Is the voltage at CON3 (P8502) No connector as specified? Yes Power circuit faulty. Hook up a personal computer. Does the image appear? No Yes Go to "Checking the clock circuit and its peripheral circuits". Is the image as specified? No Yes Check the sync signal circuit and its A peripheral circuits. Is the image's colour as specified? No Yes Check the video circuit and its peripheral circuits. Does the on-screen display function? No Yes Go to "Checking the OSD circuit and its peripheral circuits". Does the remote control function? No Yes Go to "Checking the remote control". End 39 XG-C40XU/XE TROUBLE SHOOTING TABLE (Continued) Lamp fails to light-up Yes Turn on the power switch. Is discharging sound heard from the lamp? No Is the lamp out of socket? Yes No Is the ballast cooling fan No running? Reconnect the Replace the lamp into socket. lamp. Yes Check the power circuit. Is DC 360V voltage applied No between PL connector pins? Yes Yes Is 2V or higher voltage applied between pins (1) and (2) of ballast's D connector? No Replace the ballast. Is D connector disconnected? No Yes Reconnect the Check the connector into socket. microcomputer circuit. 40 XG-C40XU/XE TROUBLE SHOOTING TABLE FOR PC I/F UNIT-1 Power On Is the input properly selected? No Select the specified input with the remote controller. Yes Are the PC, video and projector cables as specified and properly connected? No Use the specified cables. Reconnect them correctly. Yes Turn up the contrast control all the way. Is the image visible? Yes Readjust the video settings. No Is the voltage at connector P8502 as specified? No Power circuit defective. Yes Is the image invisible? Yes Go to “Checking the Clock Circuit and its Peripheral Circuits”. No Is the image distorted? Yes Go to “Checking the Sync Signal Circuit and its Peripheral Circuits”. No Are the image colors abnormal? 4 Yes Go to “Checking the Video Circuit and its Peripheral Circuits”. No Yes Does the onscreen display malfunction? Go to “Checking the OSD Circuit and its Peripheral Circuits”. No Yes Does the remote controller malfunction? Go to “Checking the Remote Controller”. No End 41 XG-C40XU/XE TROUBLE SHOOTING TABLE FOR PC I/F UNIT-2 Checking the clock circuit and its peripheral circuits Is X8001 (6MHz) oscillating? No X8001 or its peripheral part faulty. Yes Is X8003 (1.84MHz) oscillating? No X8003 or its peripheral part faulty. Yes Is X8004 (22.165MHz) oscillating? No X8004 or its peripheral part faulty. Yes Is X8005 (18.75MHz) oscillating? No X8005 or its peripheral part faulty. Yes Does pin (162) of IC8001 function? No IC8001 or its peripheral circuit faulty. Yes 5 TROUBLE SHOOTING TABLE FOR PC I/F UNIT-3 Checking the Sync Signal Circuit and its Peripheral Circuits 5 No Is the sync signal of split type? Yes Are there signals at TP8004 and TP8005? No IC8610 or terminal PWB defective. Yes No Is the sync signal of Sync On Green type? Yes No Are there signals at pin (7) of IC8611? IC8611 or its peripheral part faulty. Yes Are there signals at pins (149) (TL80 34) and (150) (TL8035) of IC8020? No IC8025 or its peripheral part faulty. Yes No Does the input have a resolution lower than XGA or is it video input? Yes Are there signals at pins (26) (TL8043), No (28) (TL8041) and (29) (TL8042) of IC8020? IC8020 or its peripheral part faulty. Yes Are there signals at pins (13) thru (52), except for GND, of P8405? No IC8029,IC8609 or its peripheral part faulty. Yes 6 42 XG-C40XU/XE TROUBLE SHOOTING TABLE FOR PC I/F UNIT-4 Checking the PLL circuit and its peripheral circuits 6 Are there signal at pins (111) and (112) of IC8606? No Yes Are there signals at pins (7) and (10) of IC8601? IC8025,IC8600 or its peripheral circuit faulty. No Yes IC8601,IC8606 or its peripheral circuit faulty. Check the video circuit and its peripheral circuits. Is image as specified at resolution above XGA level? No Check the S-XGA video circuit and its peripheral circuits. Yes Is image as specified at resolution below XGA level? No Check the VGA video circuit and its peripheral circuits. Yes Hook up a video system. Is the display as specified? Yes No Check the video system's video circuit and its peripheral circuits. 4 43 XG-C40XU/XE TROUBLE SHOOTING TABLE FOR PC I/F UNIT-5 Checking the SXGA's red video circuit and its peripheral circuits Is there signal at pin (139) of IC8606? Checking the VGA's red video circuit and its peripheral circuits No Yes Are there signals at pins (21) thru (31) as well as (34) thru (41), except for GND, of P8606? Is there signal at pin (139) of IC8606? Yes Terminal PWB,C8616 defective. No Yes Are there signals at TL8044 and TL8046? No No Are there signals at pins (21) thru (31) as well as (34) thru (41), except for GND, of P8606? Yes IC8606 or its peripheral circuit faulty. No No Are there signals at pins (112) thru (119) of IC8020? Yes Yes IC8025 or its peripheral circuit faulty. No Are there signals at pins (69) thru (73) and (189) thru (192) of IC8020? Yes IC8020 or its peripheral circuit faulty. Is there signal at pin (Y11)(TL8612) of IC8609? No Yes Are there signals at pins (1) thru (10) of IC8051? Yes IC8029 or its peripheral circuit faulty. Check the video system's red video circuit and its peripheral circuits No IC8609 or its peripheral circuit faulty. IC8051 or its peripheral circuit or output PWB faulty. No Is there signal at pin (144) of IC8606? Yes C8702 or its peripheral circuit or signal PWB faulty. 1 44 1 XG-C40XU/XE TROUBLE SHOOTING TABLE FOR PC I/F UNIT-6 Checking the SXGA's green video circuit and its peripheral circuits Is there signal at pin (124) of IC8606? Checking the VGA's green video circuit and its peripheral circuits No No Is there signal at pin (124) of IC8606? Yes Yes Terminal PWB, C8620 defective. Are there signals at pins (68) thru (75) as well as (78) thru (88), except for GND, of P8606? No Yes Are there signals at TL8045 and TL8047? No IC8606 or its peripheral circuit faulty. No No Are there signals at pins (68) thru (75) as well as (78) thru (88), except for GND, of P8606? Yes Are there signals at pins (165) thru (177) of IC8020? Yes Yes IC8025 or its peripheral circuit faulty. No Are there signals at pins (178) thru (187) of IC8020? Yes IC8020 or its peripheral circuit faulty. Is there signal at pin (V13)(TL8613) of IC8609? No Yes Are there signals at pins (11) thru (20) of IC8051? Yes IC8029 or its peripheral circuit faulty. Check the video system's green video circuit and its peripheral circuits No IC8609 or its peripheral circuit faulty. IC8051 or its peripheral circuit or output PWB faulty. No Is there signal at pin (126) of IC8606? Yes C8703 or its peripheral circuit or signal PWB faulty. 1 45 1 XG-C40XU/XE TROUBLE SHOOTING TABLE FOR PC I/F UNIT-7 Checking the SXGA's blue video circuit and its peripheral circuits Is there signal at pin (133) of IC8606? Checking the VGA's blue video circuit and its peripheral circuits No No Is there signal at pin (133) of IC8606? Yes Yes Terminal PWB, C8623 defective. Are there signals at pins (45) thru (53) as well as (56) thru (64), except for GND, of P8606? No Yes Are there signals at TL8048 and TL8049? No IC8606 or its peripheral circuit faulty. No No Are there signals at pins (45) thru (53) as well as (56) thru (64), except for GND, of P8606? Yes Are there signals at pins (85) thru (93) of IC8020? Yes Yes IC8025 or its peripheral circuit faulty. No Are there signals at pins (74) thru (83) of IC8020? Yes IC8020 or its peripheral circuit faulty. Is there signal at pin (U15)(TL8614) of IC8609? No Yes Are there signals at pins (21) thru (30) of IC8051? Yes IC8029 or its peripheral circuit faulty. Check the video system's blue video circuit and its peripheral circuits No IC8609 or its peripheral circuit faulty. IC8051 or its peripheral circuit or output PWB faulty. No Is there signal at pin (136) of IC8606? Yes C8704 or its peripheral circuit or signal PWB faulty. 1 46 1 XG-C40XU/XE TROUBLE SHOOTING TABLE FOR PC I/F UNIT-8 Checking the OSD circuit and its peripheral circuits Display OSD on the screen. No Are there signals at pins (56), (58), (71) and (72) (TL8054,TL8053,TL8052, TL8051) of IC8048? Yes Are there signals at pins (12), (14) thru (17) and (20) of IC8046? IC8029 or its peripheral circuit faulty. No Yes IC8048 or its peripheral circuit faulty. Are there signals at pins (23) thru (42) of IC8046? No Yes IC8046 or its peripheral circuit faulty. IC8048 or its peripheral circuit faulty. Checking the remote controllor Use the remote controller. Is there the signal at pin (59) of P8405? No Yes Output PWB faulty. IC8001 circuit faulty. 47 XG-C40XU/XE Technische Daten Produkttyp Modell Videosystem Wiedergabeverfahren LCD-Projektionspaneel Objektiv Projektionslampe Kontrastverhältnis Videoeingangssignal S-Videoeingangssignal Horizontale Auflösung Audioausgang RGB-Computereingangssignal Punktetakt Vertikale Frequenz Horizontale Frequenz Computereingangs-Signal Lautsprechersystem Nennspannung Eingangsspannung Nennfrequenz Nennaufnahme Betriebstemperatur Lagertemperatur Gehäuse I/R-Trägerfrequenz Laserzeiger der Fernbedienung Abmessungen (ca.) Gewicht (ca.) Mitgeliefertes Zubehör LCD Projector XG-C40XE PAL/SECAM/NTSC 3.58/NTSC 4.43/DTV 480P/DTV 720P/DTV 1080I LCD-Projektionspaneel × 3, optisches RGB-Verschlußverfahren Panelgröße: 22,9 mm (0,9) (13,9 mm [H] × 18,5 mm [B]) Wiedergabe-Verfahren: Durchlässiges TN-Flüssigkristall-Paneel Treiberverfahren: TFT (Dünnfilmtransistor) Aktivmatrix-Paneel Anzahl der Bildpunkte: 786.432 Bildpunkte (1.024 [H] × 768 [V]) 1–1,3 Zoomobjektiv, F1,7–2,0, f = 33–43 mm 200 W Gleichstrom-Lampe 250:1 RCA-Stecker: VIDEO, Gemischtes Video, 1,0 Vs-s, negatives Sync.-Signal, 75 Ω terminiert RCA-Stecker: AUDIO, 0,5 Vrms mehr als 22 kΩ (Stereo) 4-Pin Mini DIN-Stecker Y (Luminanz-Signal): 1,0 Vs-s, negatives Sync.-Signal, 75 Ω terminiert C (Chrominanz-Signal): Stoß 0,286 Vs-s, 75 Ω terminiert 560 Fernsehzeilen (Videoeingang), 750 Fernsehzeilen (DTV 720P-Eingang, Punkt für Punkt) 3 W (monaural) 15-PIN MINI D-SUB STECKANSCHLUSS (INPUT 1, 2): RGB getrennt/gemischte Sync./Sync. auf Grün-Typ analoger Eingang: 0–0,7 Vs-s, positiv, 75 Ω terminiert STEREO-MINIBUCHSE: AUDIO, 0,5 Vrms, mehr als 22 kΩ (Stereo) HORIZONTALES SYNC.-SIGNAL: TTL-Pegelsignal (positiv/negativ) oder gemischtes Sync.Signal (nur Macintosh) VERTIKALES SYNC.-SIGNAL: Wie oben 12–230 MHz 43–200 Hz 15–126 kHz 9-Pin Mini DIN-Steckanschluß (RS-232C-Eingangsanschluß) 8 cm (3 3⁄32) rund AC 100–240 V 3,3 A 50/60 Hz 300 W + 5°C bis + 40°C – 20°C bis + 60°C Kunststoff 38 kHz Wellenlänge: 650 nm / Max. Ausgang: 1 mW / Klasse II Lasergerät 229 × 121 × 310 mm (B × H × T) (nur Hauptgerät) 243,5 × 134 × 358,4 mm (B × H × T) (einschließlich Drehfüße und vorstehende Teile) 4,8 kg Fernbedienung, Zwei Batterien der Größe AA, Netzkabel (1,8 m), RGBComputerkabel (3m), Computer-Audiokabel (3 m), USB-Maus-Steuerungskabel (1,5 m), DIN-D-Sub RS-232C-Kabel (15 cm),Fernbedienungs-Mausempfänger, Ersatz-Luftfilter, Objektivkappe (angebracht), CD-ROM, Bedienungsanleitung für LCD-Projektor, Kurzreferenz für LCD-Projektor,Software-Anleitung für Sharp Advanced Presentation Ersatzteile Lampensatz (Lampe/Käfigmodul) (BQC-XGC40XU/1), Fernbedienung (RRMCG1584CESA), Batterien der Größe AA, Netzkabel (QACCB5024CENA, QACCV4002CEZZ), RGB-Computerkabel(QCNWG0002CEZZ), Computer-Audiokabel (QCNW-4870CEZZ),USB-Maus-Steuerungskabel (QCNWG0007CEPZ), DIN-D-Sub RS-232C-Kabel (QCNW-5288CEZZ), Fernbedienungs-Mausempfänger (RUNTK0673 CEZZ), Luftfilter (PFILD0076CEZZ), Objektivkappe(GCOVH1307CESB), CD-ROM (UDSKA0057CEN1), Bedienungsanleitung für LCD-Projektor (TINS-7533CEZZ), Kurzreferenz für LCD-Projektor (TINS-7534CEZZ, TINS-7535CEZZ, TINS-7536CEZZ), Software-Anleitung für Sharp Advanced Presentation(TINS-7537CEZZ) Dieser Projektor von SHARP ist mit 3 LCD- (Flüssigkristallanzeige) Projektionspaneels ausgestattet. Diese neuartigen Projektionspaneels enthalten TFTs (Dünnfilmtransistoren) mit insgesamt 786.432 Bildpunkten (× RGB). Bei allen technologisch fortschrittlichen, elektronischen Geräten, z. B. Großbild-Fernsehern, Videosystemen bzw. Videokameras, sind bestimmte Toleranzgrenzen für die Funktionen gegeben. Dieses Gerät hat einige inaktive, innerhalb akzeptierter Toleranzgrenzen liegende TFTs, die als beleuchtete oder als nicht aktive Punkte auf der Bildwand wiedergegeben werden. Dies hat keinen Einfluß auf die Bildqualität und die Lebensdauer des Gerätes. Änderungen der technischen Daten ohne vorherige Ankündigung vorbehalten. 48 XG-C40XU/XE HINWEIS FÜR DAS WARTUNGSPERSONAL 1234567890123456789012345678901212345678901234 1234567890123456789012345678901212345678901234 1234567890123456789012345678901212345678901234 Ë Auswechseln der Lampe 1234567890123456789012345678901212345678901234 ACHTUNG: UV-STRAHLUNG 1234567890123456789012345678901212345678901234 1234567890123456789012345678901212345678901234 Hinweis: Da die Lampe während des Betriebs sehr heiß wird, sollte die Lampe erst ausgewechselt werden, nachdem das Gerät mindestens eine Stunde ausgeschaltet war, damit die Lampe ausreichend abkühlen kann. Beim Installieren der neuen Lampe muß darauf geachtet werden, die Lampe selbst (Glaskolben) nicht zu berühren. Vielmehr muß die Lampe am Reflektor 2 gehalten werden. [Es darf nur ein Original-Ersatzteil verwendet werden.] Die Lichtquelle im LCD-Projektor, eine MetallHalogen-Lampe, gibt eine geringe UV-Strahlung ab. DIREKTE BESTRAHLUNG AUF AUGEN UND HAUT MUSS VERMIEDEN WERDEN. Zur Gewährleistung der Sicherheit muß folgendes beachtet werden: 1. Bei Arbeiten am Projektor bei eingeschalteter Lampe und abgenommenem oberen Gehäuse muß unbedingt eine Sonnenbrille getragen werden. 1 Lampe 2 Reflektor GEFAHR! — Niemals die Spannungsversorgung einschalten, ohne daß eine Lampe vorhanden ist, um elektrische Schläge und Schäden am Gerät zu vermeiden, da der Stabilisator anfangs hohe Spannungen erzeugt. 2. Die Lampe darf nicht außerhalb des Lampengehäuses eingeschaltet werden. Da eine geringe UV-Strahlung aus einer Öffnung zwischen der Schachtabdeckung und dem Lampengehäuse austritt, sollte der Objektivdeckel bei Wartungsarbeiten auf die Öffnung gesetzt werden, um die Bestrahlung von Augen und Haut zu vermeiden (Abb. 1). 3. Betrieb für länger als 2 Stunden bei abgenommenem Gehäuse ist nicht zulässig. Hinweis: Besorgen Sie sich einen Objektivdeckel, bevor Sie Arbeiten an einem Modell XGC40XE durchführen, das keinen Objektivdeckel aufweist. Objectivdeckel Zur Beachtung bei UV-Strahlung und Mitteldruck-Lampen 1. Vor dem Auswechseln der Lampe muß der Netzstecker gezogen werden. 2. Vor Durchführung von Wartungsarbeiten muß das Gerät eine Stunde abkühlen. 3. Nur mit dem gleichen Lampentyp ersetzen Typ CLMPF0075CE01 oder BQC-XGC40XU/1; Nennleistung 85 V / 200 W. 4. Die Lampe gibt eine geringe UV-Strahlung ab, daher muß direkter Augenkontakt vermieden werden. 5. Die Mitteldruck-Lampe weist ein Explosionsrisiko auf. Daher müssen die nachstehenden Installationsanweisungen beachtet werden, und die Lampe muß vorsichtig behandelt werden. SH AR P Abbildung 1. 49 XG-C40XU/XE BEDIENUNGSANLEITUNG Lage der Bedienelemente Projektor Stummschaltungs-Taste (MUTE) Lampenaustausch-Anzeige Temperaturwarnanzeige Betriebsanzeige Lautstärke-Tasten (VOLUME + / – ) Netz-Tasten (ON/OFF) Trapezverzeichnungs-Taste (KEYSTONE) Menü-Taste (MENU) Eingangs-Taste (INPUT) Auto-Synchron-Taste (AUTO SYNC) Größe-Taste (RESIZE) Standbild-Taste (FREEZE) GAMMA-Taste Vergrößern-Taste (ENLARGE) Schwarzbild-Taste (BLACK SCREEN) Einstellungs-Tasten ('/"/\/|) Storno-Taste (UNDO) Eingabe-Taste (ENTER) Zoom-Knopf Tragegriff Fernbedienungs-Sensor Standardanschluß für Kensington-Sicherheitssperre Fokussier-Knopf Drehfuß-Feststeller Ansicht von vorne und oben Lautsprecher Seiten- und Rückansicht Luftfilter/Kühlventilator (Lufteinlaß) Kühlventilator (Luftauslaß) Fernbedienungs-Sensor Eingangs-Port 1 (HD 15) (INPUT 1) Eingangs-Port 2 (HD 15) (INPUT 2) Audioausgangsanschluß (3,5 mm Stereo-Minibuchse) (AUDIO OUTPUT) Audioeingangsanschluß für EingangsPort 1, 2 (3,5 mm Stereo-Minibuchse) (AUDIO INPUT für INPUT 1, 2) RS-232C-Anschlußstelle (9-Pin Mini DIN) Ausangs-Port für Eingangs-Port 1, 2 (HD 15) (OUTPUT-Port für INPUT 1, 2) S-Videoeingangsanschluß 4 (4-Pin Mini DIN) (S-VIDEO INPUT) Audioeingangsanschlüsse 3 (RCA) (AUDIO INPUT 3) Videoeinganganschluß 3 (RCA) (VIDEO INPUT 3) Steckanschluß 50 XG-C40XU/XE Betrieb mit der drahtlosen Maus-Fernbedienung Fernbedienung Vorderansicht Ansicht von hinten StummschaltungsTaste (MUTE) Lautstärke-Tasten (+/–) Netz-Tasten (ON/OFF) Trapezverzeichnungs-/ Schwarzbild-Taste (KEYSTONE/BLACK SCREEN) Laserzeiger-/MenüTaste (LASER/MENU) Rechte Klick-/ Eingabe-Taste (R-CLICK/ENTER) Maus-/EinstellungsTasten ('/"/\/|) Eingangs-Taste (INPUT) Storno-Taste (UNDO) Standbild-Taste (FREEZE) Auto-Synchron-Taste (AUTO SYNC) Linke Klick-Taste (L-CLICK) Größe-Taste (RESIZE) Vergrößern-Taste (ENLARGE) Hilfsmittel-Taste (TOOLS) Maus-/EinstellungsSchalter (MOUSE/ADJ.) GAMMA-Taste Beleuchtungs-Taste (LIGHT) Ansicht von oben ÜbertragungsAnzeige Laserlichtfenster Einsetzen der Batterien 1 Zum Entfernen der Batteriefachabdeckung auf die Pfeilmarkierung drücken und in Pfeilrichtung schieben. Batteriefachabdeckung 2 Zwei Batterien der Größe AA einlegen und sicherstellen, daß die Pole mit der + und – Markierung im Batteriefach übereinstimmen. 3 Die seitlichen Vorsprünge der Batteriefachabdeckung in die entsprechenden Schlitze einsetzen und auf die Abdeckung drücken, bis sie richtig aufgeschoben ist. Batteriefachabdeckung Batteriefach 51 XG-C40XU/XE Verwendung der Fernbedienung als eine drahtlose Maus Die Fernbedienung ist mit den folgenden drei Funktionen ausgestattet: • Projektor-Steuerung • Drahtlose Maus • Laserzeiger MOUSE/ADJ.-Schalter (Fernbedienung) MOUSE ADJ. MOUSE Drahtlose Maus Laserzeiger ADJ. ProjektorSteuerung Positionierung der Fernbedienung bzw. des Mausempfängers • Die Fernbedienung kann zur Steuerung des Projektors innerhalb des unten gezeigten Bereiches verwendet werden. • Der Fernbedienungs-Mausempfänger kann mit der Fernbedienung zusammen zur Steuerung der Mausfunktion eines angeschlossenen Computers innerhalb des unten gezeigten Bereiches verwendet werden. • Das Signal der Fernbedienung kann für einen einfacheren Betrieb von der Bildwand reflektiert werden. Der wirksame Abstand des Signals kann aufgrund des Materials der Bildwand unterschiedlich sein. Steuerung des Projektors Verwendung der drahtlosen Maus Fernbedienung Fernbedienung 7m 30˚ 30˚ 30˚ 45˚ 30˚ 120˚ 4m FernbedienungsMausempfänger 45˚ 30˚ Fernbedienung 52 XG-C40XU/XE Verwendbare Tasten in der MOUSE-Betriebsart Verwendung als eine drahtlose Maus Sicherstellen, daß der mitgelieferte FernbedienungsMausempfänger am Computer angeschlossen ist. Fernbedienung (Ansicht von vorne) LASER (Den MOUSE/ADJ.-Schalter auf der Fernbedienung auf die MOUSE-Position schieben.) MOUSE ADJ. BLACK SCREEN Maus R-CLICK LIGHT • Die drahtlose Maus kann nicht richtig funktionieren, wenn der serielle Port des Computers nicht richtig eingestellt ist. Siehe die Bedienungsanleitung des Computers für Hinweise zur Einstellung bzw. Installation des Maustreibers. • Für eintastige Systeme kann sowohl L-CLICK als auch RCLICK verwendet werden. Verwendung der Fernbedienung in einem dunklen Raum Durch Drücken von LIGHT werden die Tasten beleuchtet. Die grünen Tasten bedeuten Mausbetrieb und die roten Tasten Projektoreinstellungen. Fernbedienung (Ansicht der Rückseite) Tastenbezeichnung Position des MOUSE/ADJ.-Schalters MOUSE ADJ. LASER/MENU LASER (GRÜN) MENU (ROT) BLACK SCREEN/KEYSTONE BLACK SCREEN (GRÜN) KEYSTONE (ROT) ENTER (ROT) R-CLICK/ENTER R-CLICK (GRÜN) L-CLICK '/"/\/| L-CLICK ON/OFF '/"/\/| (LEUCHTET NICHT) '/"/\/| (LEUCHTET NICHT) — JA (LEUCHTET NICHT) VOLUME + / – MUTE INPUT UNDO FREEZE AUTO SYNC JA (ROT) ENLARGE RESIZE TOOLS GAMMA Verwendung als ein Laserzeiger (Den MOUSE/ADJ.-Schalter auf der Fernbedienung auf die MOUSE-Position schieben.) MOUSE ADJ. LASER ( ) zum Aktivieren des Laserzeigers drücken. Beim Loslassen der Taste erlöscht das Licht automatisch. • Aus Sicherheitsgründen erlöscht der Laserzeiger automatisch nach einer Minute fortlaufender Verwendung. Zum Einschalten LASER ( ) loslassen und erneut drücken. 53 XG-C40XU/XE Pinbelegung Analoger Computer-Signaleingang 1 und 2: 15-Pin Mini-D-Sub-Buchse 1 6 11 5 10 15 Computereingang Analog 1. Videoeingang (rot) 2. Videoeingang (Grün/Sync. auf Grün) 3. Videoeingang (blau) 4. Reserveeingang 1 5. Gemischtes Sync.-Signal 6. Erdung (rot) 7. Erdung (Grün/Sync. auf Grün) 8. Erdung (blau) 9. 10. 11. 12. 13. Nicht belegt MASSE MASSE Bi-direktionale Daten Horizontales Sync.Signal 14. Vertikales Sync.-Signal 15. Daten-Zeitgeber Komponenten-Eingang 1. 2. 3. 4. 5. 6. 7. 8. PR(CR) Y PB Nicht belegt Nicht belegt Erdung (PR) Erdung (Y) Erdung (PB) 9. 10. 11. 12. 13. 14. 15. Nicht belegt Nicht belegt Nicht belegt Nicht belegt Nicht belegt Nicht belegt Nicht belegt RS-232C-Anschlußstelle: 9-Pin D-Sub-Stecker des DIN-D-Sub RS-232C-Kabels Pin Nr. 1 2 3 4 5 6 7 8 9 5 1 9 6 Signal CD RD SD ER SG DR RS CS CI Name E/A Daten empfangen Daten senden Eingang Ausgang Signalerdung Ausgang Datensatz bereit Anforderung zum Senden Ausgang Bereit zum Senden Eingang Referenz Nicht angeschlossen An internen Schaltkreis angeschlossen An internen Schaltkreis angeschlossen Nicht angeschlossen An internen Schaltkreis angeschlossen Nicht angeschlossen An internen Schaltkreis angeschlossen An internen Schaltkreis angeschlossen Nicht angeschlossen RS-232C-Anschlußstelle: 9-Pin Mini DIN-Steckanschluß 8 7 9 6 3 5 4 2 1 Pin Nr. 1 2 3 4 Signal VCC RD SD EXIR 5 6 SG ERX 7 8 9 RS CS ETX Name + 3,3 V (Reserviert) Daten empfangen Daten senden Detektor für Zusatzgerät (Reserviert) Signalerdung IR Empfangssignal von IR-Verstärker (Reserviert) Aufforderung zum Senden Bereit zum Senden IR-Signalübertragung (Reserviert) 54 E/A Ausgang Eingang Ausgang Eingang Referenz Nicht angeschlossen An internen Schaltkreis angeschlossen An internen Schaltkreis angeschlossen Nicht angeschlossen Eingang An internen Schaltkreis angeschlossen Nicht angeschlossen Ausgang Eingang Ausgang An internen Schaltkreis angeschlossen An internen Schaltkreis angeschlossen Nicht angeschlossen XG-C40XU/XE Ansicht der Rückseite Abmessungen 25 23 /64 (9) 3 51/64 (96,5) 23 105/16 (262) 147/64 (358,4) 5 19/32 (142) 1213/64 (310) 2 13/32 (61) /64 (9) 2 13 /32 (61) 5433/64 (138,5) 9 11/32 (237,5) 49 1/64 (124,5) 1 5/16 (33,5) /64 (10) 29/32 (23) 3 53/64 (97,5) 1 5/64 (27,5) Ansicht von oben w /8 (16) 63 1 11/16 (43) 2 /64 (76) 919/32 (243,5) 13 / (25) 7 16 / (11) 5 9/32 (134) Ansicht von vorne 17/32 (13) 449/64 (121) /32 (10,5) 3 21/32 (93) 113/16 (30) 3 17/64 (83) 9 1/64 (229) 63 64 3 17/64 (83) 5 Seitenansicht Ansicht von unten Einheit: zoll(mm) 55 XG-C40XU/XE ENTFERNEN DER HAUPTTEILE 1. Entfernen der Lufteinlaßabdeckung und der Lampeneinheit S A H P R 1-1. Die Lufteinlaßbdeckung abnehmen 1-2. Die Schraube der Lampenkäfigabdeckung losdrehen und dann die Lampenkäfigabdeckung in Pfeilrichtung (zum Körper) herausziehen. 1-3. Die beiden Sicherungsschrauben der Lampeneinheit losdrehen und die Lampeneinheit abnehmen. Lampeneinheit 1-3 1-3 1-2 Lufteinlaßabdeckung 1-1 Lampenkäfigabdeckung Hinweis: Beim Lampenaustausch sicherstellen, daß der Anschluß und die Schnappklemmfeder (sowie die anderen Metallteile) der Lampe mehr als 8 mm Abstand voneinander haben. 56 XG-C40XU/XE 2. Entfernen des oberen und hinteren Gehäuseteils 2-1. Die vier Schrauben vom hinteren Gehäuseteil losdrehen. 2-2. Die vier Schrauben der Anschlußplatte vom hinteren Gehäuseteil losdrehen. Das hintere Gehäuseteil von unten aushängen und abnehmen. 2-3. Von unten die vier Schrauben vom oberen Gehäuseteil losdrehen. H S R A P Zum Aushaken gleichzeitig in Pfeilrichtung auf beide Seiten des Gehäuseunterteils drücken. Danach den oberen Gehäuseteil nach oben abnehmen. 2-1 2-3 Haken 2-2 2-4. Das obere Gehäuseteil langsam anheben und den Platinen-Netzschalterstecker (KY) abziehen und schließlich das Oberteil abnehmen. Oberes Gehäuseteil (KY) 2-4 Hinteres Gehäuseteil 57 XG-C40XU/XE 3. Entfernen der Platinen 3-1. Die Stecker von der Ausgabe-Einheit abziehen. 3-2. Die vier Befestigungsschrauben der PC-Schnittstelle-Einheit losdrehen. Die beiden Schrauben und den Erdungsschirm entfernen, und die PC-Schnittstelle-Einheit abnehmen. 3-3. Das Abstandsstück (Stiftschraube) und die drei Schrauben der Ausgabe-Einheit entfernen. Die Ausgabe-Einheit anheben, dann zusammen mit der Signal-Einheit herausnehmen. 3-4. Die Schraube des Haltewinkels der S-Ausgang/REG-Einheit losdrehen und die Einheit abnehmen. 3-2 PC-Schnittstelleneinheit (TP) (L) 3-3 3-1 3-3 (FN) (Q) (EB) Abstandsstück (Stiftschraube) Ausgangsplatineneinheit 3-4 (FP)(FS) 3-3 (SO) 3-2 (F) Signalplatineneinheit (EB) 3-1 PC-Schnittstellen-Platine Haltewinkel der S-Ausgang/REG-Einheit (EA) (SP) (SO) S-Ausgang/REG-Einheit Videoeinheit 58 XG-C40XU/XE 4. Entfernen der Optik-Mechanismuseinheit 4-1. Die sechs Schrauben der Optik-Mechanismuseinheit losdrehen und dann die Einheit herausnehmen. 4-2. Die beiden Schrauben des Lampenfassungshalters losdrehen und den Halter abnehmen. 4-1 Kühlschachteinheit 4-2 Optik-Mechanismuseinheit 59 XG-C40XU/XE 5. Entfernen der Netz/Ballast-Platineneinheit 5-1. Die Schraube der Netz/Ballast-Platineneinheit losdrehen. 5-2. Die Schraube des Anschlußdrahts (FG) losdrehen. 5-3. Die Netz/Ballast-Platineneinheit anheben und herausziehen. 6. Entfernen der Ballast-Platineneinheit und der Eingangseinheit 6-1. Den Stecker (PA) von der Eingangseinheit abziehen und den Netzschalter herausnehmen. 6-2. Die Sicherungsschraube der Eingabe-Einheit entfernen. 6-3. Die Eingangseinheit zum Körper herausziehen. Hinweis: Vor dem Einbau der Lampenkäfigabdeckung sicherstellen, daß der Netzschalter in Position “ ist. 5-1 5-2 Netz/Ballast-Platineneinheit (FG) (TP) 5-3 Netzschalter (bei Lampenaustausch) (BA) (PA) 6-1 (FG) 6-2 (PA) 6-3 Eingangseinheit 60 ” (AUS) XG-C40XU/XE NULLSTELLUNG DES LAMPEN-BETRIEBSSTUNDENZÄHLERS (GESAMTZEIT) Nachdem die Lampe ausgewechselt wurde, ist die aufgelaufene Gesamtzeit des LampenBetriebsstundenzählers in folgenden Schritten nullzustellen. Nullstellungsverfahren 1. Während die Tasten “ENTER”, “ADJ."” und “ADJ.|” gleichzeitig gedrückt gehalten werden, den Hauptgeräteschalter aktivieren (befindet sich über dem Netzeingang). 2. Der Wert des Lampen-Betriebsstundenzählers ist nun auf Null zurückgestellt. “000H” erscheint auf dem Bildschirm. LAMP POWER ON I TEMP. + MUTE VOLUME OFF MENU KEYSTONE AUTO SYNC INPUT ' BLACK SCREEN ' ' ENLARGE ' FREEZE RESIZE GAMMA ENTER UNDO B ENTER ADJ." (Einstellung) ADJ.| (Einstellung) Lampe Die Lampe dieses Projektors kann abhängig von der Betriebsumgebung etwa 2,000 Stunden verwendet werden. Es wird empfohlen, die Lampe nach 1,900 Betriebsstunden oder wenn eine sichtbare Verschlechterung der Bildund Farbqualität auftritt, auszutauschen. Die Verwendungszeit der Lampe kann mit der Anzeige auf der Bildwand überprüft werden. VORSICHT • Gefährliche Lichtstrahlen. Niemals beim Betrieb des Projektors in die Öffnung oder das Objektiv schauen. • Wenn die Betriebsumgebung große Unterschiede aufweist, kann die Verwendungdauer der Lampe weniger als 2,000 Stunden betragen. Symptom Die Lampenaustausch-Anzeige leuchtet rot auf und „LAMP.“ und „ “ blinken gelb in der unteren linken Ecke der Bildwand. Problem • Die Lampe wurde über 1,900 Stunden verwendet. Eine sichtbare Verschlechterung der Bild- und Farbqualität tritt auf. Das Gerät wird automatisch ausgeschaltet und der Projektor auf Betriebsbereitschaft geschaltet. • Die Lampe wurde über 2,000 Stunden verwendet. „LAMP.“ und „ “ blinken rot in der unteren linken Ecke der Bildwand und das Gerät wird automatisch ausgeschaltet. 61 Abhilfe • Einen Austauschlampen-Satz (Lampe/Käfigmodul) des gegenwärtigen Typs BQCXGC40XU/1 beim nächsten von Sharp autorisierten Händler für LCD-Projektoren oder dem Kundendienst kaufen. • Die Lampe austauschen. Sie können die Lampe auch bei einem von Sharp autorisierten Händler für LCD-Projektoren oder dem Kundendienst austauschen lassen. XG-C40XU/XE ÜBERSICHT DER OPTIKEINHEIT Übersicht des optischen Systems Hinweis: Anordnung der Bauteile im optischen System Projektionsobjektiv Polarisatorplatte B für austretendes Licht Polarisatorplatte B für einfallendes Licht Polarisatorplatte R für austretendes Licht Zweifarbige Beschichtung(R-Übertragung) R-LCD AR-Beschichtung B-LCD or ef R or B- kt CL2 RL3 Relaislinse 3 Relaislinse 2 RL2 Kondensatorlinse R Polarisationsfolie Polarisatorplatte G Zweifarbige für austretendes Licht Beschichtung Polarisationsfolie (R-Reflexion) G-LCD Zweifarbige Beschichtung (G-Übertragung) CL3 Kondensatorlinse G GRÜN Markierung (Boden) ROT M2 B/ -R G ef le or Relaislinse 1 UV-IR -Beschichtung Markierung kt or M3 kt RL1 le Zweifarbige Beschichtung CL1 DC-Lampe (Lichtquelle) pi e ge lW PBS (PolarisationsStrahlenteiler) te rS Oberfläche Ag-Deposit ch hi -b es c M1 Ag or kt le ef ef R -R B- BLAU G M4/M6 te UV-Filter le BLAU UV-Filter(0.8t) Zweifarbige Beschichtung (B-Reflexion) ef le kt -R Zweifarbige Beschichtung (B-Reflexion) M5 R M4/M6 Zweifarbiges Kreuzprisma Fliegenaugenoptik (austretendes Licht) Fliegenauge-Linse Fliegenaugenoptik (einfallendes Licht) 62 XG-C40XU/XE EINSTELLUNG VON KONVERGENZ UND BRENNPUNKT » Bei eingeschaltetem Gerät und entferntem oberen Gehäuseteil mit der Konvergenz- und Brennpunkteinstellung beginnen. Die Bildeinstellung erfolgt mit der Fernbedienung. Es sind die folgenden Bedienschritte auszuführen: 1. Fokussieren des Projektionsobjektivs (A) Auswechseln aller 3 Flüssigkristallanzeigen (LCD) 1. Vor dem Auswechseln aller 3 Flüssigkristallanzeigen ist ein Bild auf die Leinwand zu projizieren und scharf einzustellen. 2. Die Flüssigkristallanzeigen durch neue ersetzen. Solange der Brennpunkt jedoch nicht vollständig eingestellt ist, sicherstellen, daß der Abstand zwischen dem Projektor und der Leinwand nicht verändert wird. Der Fokussierring des Projektionsobjektivs und der Zoomring dürfen ebenfalls nicht verändert werden. Hinweis: Wenn der Fokussierring mit einem unterschiedlichen Positionsverhältnis nachgestellt wird, wird das Verhältnis zwischen der Projektionsdistanz und der Leinwandgröße beeinflußt. Mit anderen Worten gesagt, kann ein Kurzdistanz-Bild (z.B. 40 mm Weitwinkel) außerhalb des Fokusbereichs liegen, während eine Zoomaufnahme (z.B. 300 Teleobjektiv) ebenfalls außerhalb des zulässigen Bereichs liegt. (B) Auswechseln von nur 1 oder 2 Anzeigen 1. Wenn nach dem Auswechseln von einer oder zwei LCD-Anzeigen eine Brennpunkteinstellung vorgenommen wird, ein Bild auf die Leinwand projizieren, dann Fokussierring verstellen, um die nicht ausgewechselte LCD-Anzeige in den Brennpunkt zu bringen. 2. Solange der Brennpunkt für beide neuen LCD-Anzeigen jedoch noch nicht vollständig abgeschlossen ist, unbedingt darauf achten, daß der Abstand zwischen dem Gerät und der Leinwand nicht verändert wird. Der Fokussierring des Projektionsobjektivs und der Zoomring dürfen ebenfalls nicht verändert werden. 3. Wenn die Projektionsdistanz geändert oder das Projektionsobjektiv verstellt worden ist, sind die obigen Schritte 1 und 2 zu wiederholen. 2. Brennpunkteinstellung (A) Einstellen der G-LCD-Anzeige (Diese Einstellung nur auf weißer Leinwand vornehmen.) 1. Einstellung in θX- und Z-Richtung Die Sicherungsschraube “a” lockern und einen exzentrischen Schraubendreher in die Kerbe und Bohrung “a” einführen. Den Schraubendreher so lange drehen, bis sich die obere Hälfte, die Mitte und die untere Hälfte der Leinwand im Brennpunkt befinden. Bei dieser Brennpunkteinstellung von oben nach unten die Sicherungsschrauben “b” und “c” anziehen, um die θY-Richtung zu fixieren. Zunächst die linke und rechte Hälfte ausbalancieren und dann die Genauigkeit während der folgenden Einstellung 2 verbessern. 2. Einstellung in θY-Richtung Die Sicherungsschraube “a” vorübergehend festziehen und die Sicherungsschrauben “b” und “c” lockern. Den exzentrischen Schraubendreher in die Kerbe und Bohrung “c” einführen, um die Einstellung in θYRichtung auf der oberen Leinwandhälfte auszuführen. Den exzentrischen Schraubendreher in die Kerbe und Bohrung “b” einführen, um die Einstellung in θY-Richtung auf der unteren Leinwandhälfte auszuführen. 3. Die obigen Schritte 1 und 2 wiederholen, um den Brennpunkt feineinzustellen. Schließlich sämtliche Sicherungsschrauben gut festziehen. Hinweis: 1 Mit der Brennpunkteinstellung vorsichtig voranschreiten, da die Einstellpositionen in gegenseitigem Bezug zueinander stehen. 2 Bei der Einstellung der Konvergenz und des Brennpunkts darauf achten, daß das Zoomobjektiv und die Einstellringe bis zur Beendigung aller Einstellungen nicht verstellt werden. (B) Einstellung der B-LCD-Anzeige (ebenso bei der R-LCD-Anzeige) 1. Das gleiche Verfahren wie bei der Brennpunkteinstellung der G-LCD-Anzeige vornehmen. Es wird darauf hingewiesen, daß der Einstellbereich in Z-Richtung klein ist. Sollten die Konvergenzwerte zwischen der BLCD-Anzeige und der G-LCD-Anzeige zu unterschiedlich sein, die Konvergenz zuerst grobeinstellen und dann die Brennpunkteinstellung vornehmen. 3. Einstellung der Konvergenz » Für diese Einstellung ist ein Kreuzschraffier-Muster zu benutzen. Die Einstellung ist ausschließlich für die G-LCD und die zutreffende Farbe. 63 XG-C40XU/XE 1. Die Konvergenz-Sicherungsschraube “d” lockern. 2. Einstellung in Y- und θZ-Richtung Den Innensechskantschlüssel im Y- und θZ-Richtung-Einstellbereich einsetzen. 3. Einstellung in X-Richtung Einen Einstellschlüssel mit Exzenternocken in den X-Richtung-Einstellbereich einsetzen. 4. Mit der G-LCD-Anzeige als Referenz die R-LCD- und die B-LCD-Anzeige einstellen. 5. Zum Schluß die Konvergenz-Sicherungsschraube “d” sicher festziehen. Hinweis: 1 Der exzentrische Nocken wird für die Einstellung der Konvergenz benutzt. Das bedeutet daß sich der Nocken dreht und die Linearbewegung nicht immer gleichmäßig verläuft. 2 Dieses Modell ist nicht mit einem LCD-Bildeinstellmechanismus ausgerüstst. Der Grund liegt in der Benutzung des zweifarbigen Prismas für die Bildformierung. Wenn alle LCD-Anzeigen optimal fokussiert sind, sind die Bilder fast vollständig konvergiert. Konvergenz- und Brennpunkt-Einstellmechanismus DRAUFSICHT SEITENANSICHT Sicherungsschraube “a” R-LCD Kerbe und Loch “c” Sicherungsschraube “c” Befestigungsschrauben für G-LCD-Anzeige (vier Schrauben) G-LCD G-LCD Sicherungsschraube “b” Kerbe und Loch “b” Sicherungsschraube “c” Kerbe und Loch “c” B-LCD Kerbe und Loch “a” SEITENANSICHT (von außen) SEITENANSICHT (von innen) Sicherungsschraube “d” Sicherungsschraube “d” Exzentrischer Nocken (Y-Richtungseinstellung) Befestigungsschrauben für R·B-LCD-Anzeige (vier Schrauben) R·B-LCD 64 Exzentrischer Nocken (X-Richtungseinstellung) Exzentrischer Nocken (θZ-Richtungseinstellung) XG-C40XU/XE Konvergenz- und Brennpunkteinstellungen auf einen Blick Einstellrichtungen Einstellung Konvergenz Brennpunkt Richtung Definition X-Richtung Y-Richtung θZ-Richtung Drehung um die Z-Achse Z-Richtung θX-Richtung Drehung um die X-Achse θY-Richtung Drehung um die Y-Achse Richtung der LCD-Anzeige LCD rechts und links LCD oben und unten LCD-Drehachse LCD, optische Achse LCD, oben bis unten (flattert) LCD, rechts bis links (flattert) Konvergenz- und Brennpunkteinstellung für den Optikmechanismus Farbe Einstellung Richtung Bewegung Position Einstellwerkzeug Sicherungsschraube Festziehwerkzeug X-Richtung ±0.8mm Exzentrischer Nocken Einstellschlüssel für exzentrischen Nocken d Innensechskantschlüssel Konvergenz Y-Richtung ±0.8mm Exzentrischer Nocken Einstellschlüssel für exzentrischen Nocken d Innensechskantschlüssel θZ-Richtung ±1° R/B -Farben Z-Richtung ±0.8mm Kerbe und Loch “a” und “c” Exzentrischer Schraubendreher Brennpunkt θX-Richtung ±1° θY-Richtung ±1° Z-Richtung Exzentrischer Nocken Einstellschlüssel für exzentrischen Nocken d Innensechskantschlüssel a, c Kerbe und Loch “a” und “c” Flachkopf-Schraubendreher a, c Kerbe und Loch “b” und “c” b, c Kreuzschlitz -Schraubendreher *Innensechskantschlüssel ±0.2mm G-Farbe Brennpunkt θX-Richtung ±1° Gleich wie für R- und B-Farben θY-Richtung ±1° Brennpunkteinstellung in die andere Richtung Sicherungsschraube Position a Kerbe und Loch “a” b Kerbe und Loch “b” c Kerbe und Loch “c” Zugehörige Richtung Richtungen Z und θX θY-Richtung Richtungen Z, θX und θY Konvergenz- und Brennpunkteinstellung sowie Festziehwerkzeuge Werkzeug Spezifisch oder allgemein Werkzeugcode Exzentrischer spezifisch 9DASPN-XGNV1U Nockeneinstellschlüssel spezifisch 80 9DADRiVER-NV4U 100 16 9EQLNC-XGNV1U Innensechskantschlüssel allgemein (verändert) ABTRENNEN 5 Exzentrischer Schraubendreher Konfiguration R2 50 2 92 5 7.5 9EQLNC-XGNV4U 2 0.5 2 allgemein *Innensechskantschlüssel allgemein 65 ø5 KreuzschlitzSchraubendreher min85 9EQDRiVER-NV1B ø3.5 allgemein 3.5 FlachkopfSchraubendreher — Für Linsenrundkopfschraube M2.6 — 1,27 mm; vorzugsweise einen Schraubendreher von mindestens 70 mm Länge (einschließlich Heft) verwenden. XG-C40XU/XE Austausch der Flüssigkristallanzeigen (LCDs) Nach Ausbau des oberen Gehäuseteils und der Optik-Mechanismuseinheit: (1) Die vier Sicherungsschrauben des Prismahalters losdrehen und den Prismahalter von der Optik-Mechanismuseinheit trennen. (2) Die Sicherungsschrauben der LCD-Anzeigen losdrehen (jeweils drei bei R-, G- und B-LCD-Anzeige). Danach die LCD-Anzeigen vom Prismahalter abnehmen. (3) Die neue LCD-Anzeige in umgekehrter obiger Reihenfolge (1) und (2) wieder anbringen. ~ Konvergenz und Brennpunkt einstellen. Es ist zu beachten, daß die G-LCD-Anzeige keine Konvergenzeinstellung erfordert und einen kleinen Einstellbereich in Z-Richtung aufweist. 1 Prismahalter Optik-Mechanismuseinheit SEITENANSICHT SEITENANSICHT (von innen) Sicherungsschraube “d” Sicherungsschraube “d” 2 Befestigungsschrauben für R·B-LCD-Anzeige R·B-LCD 66 G-LCD 2 Befestigungsschrauben für G-LCD-Anzeige XG-C40XU/XE Einstellung der optischen Achse der Spiegel (M1, M5 und M4/M6) Die optische Achse muß nachjustiert werden, wenn mit den R-, G- oder B-Spiegeln eine Verdunkelung auftritt. Im allgemeinen wird diese Einstellung erforderlich, wenn irgendeine zur Optik zählende Komponente ausgewechselt wird. Erforderliches Einstellverfahren, wenn eine der Platten ausgewechselt oder die Konvergenz eingestellt wurde: (1) Die Flachkabel von allen LCD-Tafeln abziehen. (2) Die Lampe einschalten. (3) Um den G-Spiegel einzustellen, sind die R- und B-Spiegel mit Abschirmplatten abzudecken. (Um das Licht zu blockieren, kann eine Visitenkarte oder etwas ähnliches verwendet werden.) (4) Die Schraube des M1-Einstellhebels lockern. (5) Das G-Bild am Bildschirm betrachten und den M1-Einstellhebel soweit verschieben, bis die Abdunkelung am Bildschirm verschwindet. Danach die Schraube wieder festziehen. (6) Um den R-Spiegel einzustellen, sind die G- und B-Spiegel mit Abschirmplatten abzudecken und der M5-Einstellhebel einzustellen. Für den B-Spiegel sind die R- und G-Spiegel mit dem M6-Einstellhebel einzustellen. (Die obigen Schritte 4 und 5 durchführen.) (7) Alle Abschirmplatten entfernen, die weiß sind. Sicherstellen, daß keine Verdunkelung vorherrscht. Abschirmplatte B Abschirmplatte R VORNE M4/M6 Einstellhebel Schrauben M5 Einstellhebel Schrauben schieben drehen drehen schieben Abschirmplatte G M1 Einstellhebel drehen schieben Schrauben 67 XG-C40XU/XE ELEKTRISCHE EINSTELLUNG Einen Signalgenerator, PC oder Macintosh-Computer am Projektor anschließen, um die in den Einstellbedingungen spezifizierten Signale zuzuführen. Nr. Einstellposition Einstellbedingung Einstellverfahren 1. Den Netzschalter einschalten und das Gerät für ca. 15 Minuten vorwärmen lassen. (Sicherstellen, daß die Kontrollampe aufleuchtet.) » Folgende Einstellungen vornehmen: SW5101 drücken, um den Verarbeitungsmodus abzurufen, und um S2 im SSS-Menü auszuführen. Das System ist nun initialisiert (PC-Platine nicht miteingeschlossen). S1 darf nicht ausgeführt werden, da die PC-Platine sonst initialisiert wird. Um die Platine einzustellen, die Vorschriften in "Einstellung der Platine" folgen. (Siehe seite 74) 1 EEPROMInitialisierung 2 1. Den Netzschalter 3,3 Veinschalten. Stromversorgungs2. Den Digitalvoltmeter an Einstellung TP1446 anschließen. » R1649 einstellen, bis der Voltmeter 3,43 V ±0.03 Vs-s zeigt. 3 1. Den Netzschalter 2,5 Veinschalten. Stromversorgungs2. Den Digitalvoltmeter an Einstellung TP1447 anschließen. » R1652 einstellen, bis der Voltmeter 2,60 V ±0.05 Vs-s zeigt. 4 R-Antrieb 1. Das Rotsignal (100%) zuführen und die folgende Wahl treffen. Gruppe : Analog/Digital Gegenstand: R-D » Die Regelschalter oder die Tasten auf der Fernbedienung betätigen und die Daten so einstellen, daß das Signal "bitlos" (Störung) wird. 5 B-Antrieb 1. Das Blausignal (100%) zuführen und die folgende Wahl treffen. Gruppe : Analog/Digital Gegenstand : B-D » UDie Regelschalter oder die Tasten auf der Fernbedienung betätigen und die Daten so einstellen, daß das Signal "bitlos" (Störung) wird. 6 G-Antrieb 1. Das Grünsignal (100%) zuführen und die folgende Wahl treffen. Gruppe : Analog/Digital Gegenstand : G-D » Die Regelschalter oder die Tasten auf der Fernbedienung betätigen und die Daten so einstellen, daß das Signal "bitlos" (Störung) wird. 7 1. Die folgende Wahl treffen. SchwarzpegelGruppe : OUTPUT 1 Signalamplitude Gegenstand : G1-BLK für RGB 1G1-GAIN System Für Rot sind die (ungeradzahlig) Gegenstände R1-BLK und R1-GAIN zu wählen. Für Blau sind die Gegenstände B1-BLK und B1-GAIN zu wählen. 2. Das Oszilloskop anschließen an TP1101 für Rot. TP1201 für Grün. TP1301 für Blau. » Den Gegenstand G1-GAIN wählen und den Schwarz-Spitzenpegel auf 3,3 ±0,1 Vs-s Gleichspannung einstellen. Hierfür die Regelschalter oder die Tasten auf der Fernbedienung betätigen. » Danach den Gegenstand G1-BLK wählen und die Weiß-zu-Weiß Pegeldifferenz auf 2,6 ±0,1 VGleichstrom einstellen. 2.6V (Für Rot und Blau auf 2,6 V einstellen.) 3,3Vs-s (Für Grün und Blau auf 3,3 Vs-s einstellen.) » Die Signalamplitude auf 3,3 ±0,1 Vs-s und die Weiß-zu-Weiß Pegeldifferenz auf 2,6 ±0,1 VGleichstrom für das Rot und Blau einstellen. 68 XG-C40XU/XE Nr. 8 Einstellposition P-SIGNAL Einstellbedingung 1. Das Oszilloskop anschließen an TP1701 für Rot. TP1702 für Grün. TP1703 für Blau. 2. Die folgende Wahl treffen. Gruppe : OUTPUT 2 Gegenstand : PSIG-H PSIG-L Einstellverfahren » Die P-SIG-Wellenform auf die nachstehende Form einstellen. (Mit PSIG-H einstellen.) P-Signal 6,2±0,2V Gleichstrom 2,0V Gleichstrom GND (Mit PSIG-L einstellen.) » Sicherstellen, daß die Wellenformen für Grün und Blau ähnlich wie die Wellenform für Rot sind. » Sich vergewissern, daß der Nadelstreifen aller 12 Punkte nicht seitwärts am 10-Stufensignal erscheint. (Wenn weiß oder schwarze Nadelstreifen erscheinen, ist die Einstellung mit PSIG-H vorzunehmen.) 1. Das Geisterbild-Prüfmuster » Einstellung ENR-PHASE (Geisterbild-Einstellung XGA60Hz (schwarz R-LCD) hervorgehobene Zeichen 1 Den Einstellwert erhöhen, bis ein Geisterbild auf einem (siehe Hinweis) auf der linken Seite der Halbton-RGB-Hintergrund) schwarzen Zeichen auf dem projizieren. R-Halbton-Hintergrund sichtbar wird. Gruppe: OUTPUT3 2 Den Einstellwert schrittweise reduzieren, bis das Geisterbild auf der linken Seite 2. Einstellung GCK-PHASE verschwindet (des obigen Schritts 1). Sich vergewissern, daß die 3 Den Einstellwert um einen weiteren Punkt Einstellung auf 8 reduzieren. (Anfangswert) fixiert wurde. » Einstellung ENG-PHASE (Geisterbild-Einstellung G-LCD) 3. Einstellung EN-WIDTH Das G-Geisterbild nach den gleichen Anweisungen Sich vergewissern, daß die wie im obigen Schritt 1 einstellen. Einstellung auf 8 » Einstellung ENB-PHASE (Geisterbild-Einstellung (Anfangswert) fixiert wurde. B-LCD) Das G-Geisterbild nach den gleichen Anweisungen 4. Einstellung ENR-PHASE wie im obigen Schritt 1 einstellen. (Geisterbild-Einstellung Hinweis: Left-hand ghost image: Characters are R-LCD) shown double 12 dots left from the real characters. 5. Einstellung ENG-PHASE Referenz: Diese Einstellung muß vorgenommen (Geisterbild-Einstellung werden, da ein EPSON LCD-Bildschirm eine G-LCD) Variation von 1 oder 2 Punkten aufweisen kann, abhängig von der Herstellungsserie. 6. Einstellung ENB-PHASE (Geisterbild-Einstellung B-LCD) 9 Einstellung mit Geisterbildern 10 1. Das XGAMuster- und Schwarzwertsignal (75 Hz) Halteimpulsphase zuführen. RCK-PHASE 2. Folgende Wahl vornehmen: GCK-PHASE Gruppe : OUTPUT 3 BCK-PHASE Gegenstand: SH-PHASE (Den Standardpegel auf 2 halten.) Die RCK-, GCK- und BCKPhaseneinstellungen auf 8 fixieren. » Die Einstellung mit den Regelschaltern oder den Fernbedienungstasten vornehmen. Dabei die Einstellung so durchführen, daß die "OUTPUT 3"Zeichen nicht verschwommen sind bzw. überlappen. Wenn die Zeichen verschwommen sind oder überlappen, muß die Einstellung im Bereich zwischen 7 bis 9 ausgeführt werden. 69 XG-C40XU/XE Nr. Einstellposition Einstellbedingung Einstellverfahren 11 1. Das 25%-Schwarz/RotEinstellung der Streifensignal (XGA) RGBzuführen. Gegenspannung 2. Folgende Wahl vornehmen: Gruppe : OUTPUT 3 Gegenstand : RC (R) und Gruppe : OUTPUT 3 Gegenstand : RC-INV (R) 12 Regenerierungseinstellung für RGB-Abstufung » Die Daten einstellen, um das Bildflimmern zu reduzieren. Hierfür die Regelschalter oder die Tasten auf der Fernbedienung betätigen. » Die gleichen Einstellungen für BC (B), GC (G), RC-INV (B) und RC-INV (G) vornehmen. » Sicherstellen, daß beide Seiten rechts und links am Bildschirm mittig ausgerichtet sind. Falls dies nicht der Fall ist, muß der Bildschirm so eingestellt werden, daß das Bild rechts und links identisch ist. » Die G-BLK-Daten einstellen, bis die erste Abstufung 1(95% und 100% weiß; nachfolgend aufgeführt) geringfügig erkannt werden kann. Sicherstellen, daß die zweite Abstufung 2(0% und 5% schwarz) sichtbar ist. 1. Das SMPTESignalmustersignal (nur Grün) zuführen (XGA). Gruppe : OUTPUT 1 Gegenstand : G1-BLK 2 1 13 RGBWeißbalance 1. Das Grauskalensignal (32 Abstufungen) zuführen (XGA). Gruppe : OUTPUT 1 Gegenstand : R1-BLK (R) B1-BLK (B) » Die Posten R1-BLK und B1-BLK wählen und die Schwarzbalance der Abstufung einstellen. 14 Horizontal center 1. Das NTSCMonoskopsignal zuführen. 2. Gruppe : VIDEO 2 Gegenstand : N358-DLY (4) N443-DLY (0) PAL-DLY (3) SECAM-DLY (0) Sicherstellen, daß die Einstellungen richtigeingestellt sind. 3. Gruppe : VIDEO 1 Gegenstand : NTSC-H » Die Daten einstellen, um den gleichen ÜberscanWert zu erzielen. Hierfür die Regelschalter oder die Tasten auf der Fernbedienung betätigen. 15 Einstellung des Videobilds 1. Das Trennfarbbalkensignal » Die Schwarz-zu-Weiß Signalpegeldifferenz (100%) zuführen. auf 2,0 ±0,02 Vs-s einstellen. Hierfür die Gruppe : VIDEO 1 Regelschalter oder die Tasten auf der Gegenstand : PICTURE Fernbedienung betätigen. 2. Ein Oszilloskop zwischen Stift (2) von P801 und GND anschließen. 2.0Vs-s 70 XG-C40XU/XE Nr. Einstellposition Einstellbedingung Einstellverfahren 16 Einstellung der Bildhelligkeit 1. Das Grundfrequenzsignal » Mit den Regelschaltern am Gerät oder über die (Trennfarbbalkensignal) Fernbedienung die Daten so einstellen, daß das Schwarzsignal “bitlos” wird. zuführen. (Das ON-AIRSignal ist nicht zulässig, da es zu viele Störungen erzeugt.) Gruppe : VIDEO2 Gegenstand :VROS/VGOS/VBOS 2. Den Regelschalter oder die Stummschalttaste auf der Fernbedienung drücken, um die Gammakorrektur auf die Verarbeitungseinstellung einzustellen. 17 Video-AGC 1. Das getrennte » Unter Verwendung der Steuerschalter oder der Farbbalkensignal zuführen. Fernbedienungstasten die Einstellung so Gruppe: VIDEO 1 vornehmen, daß das Weißsignal bitlos wird. Gegenstand: AGC 18 Farbton 1. Das Trennfarbbalkensignal » Die Daten so einstellen, daß die -(B-Y)-Welle zuführen. geradlinig abfällt. Hierfür die Regelschalter oder die Tasten auf der Fernbedienung betätigen. Gruppe : VIDEO 1 Gegenstand : TINT 2. Das Oszilloskop am Stift(4) von P801 anschließen. » Nach der Einstellung den Wert von TINT um 3 Punkte erhöhen. 19 20 1. Das Trennfarbbalkensignal NTSCzuführen. Farbsättigungspegel Gruppe : VIDEO 1 Gegenstand : N-COLOR 2. Das Oszilloskop am Stift(1) von P801 anschließen. » Die Differenz (100%) des Weiß- und Rotanteils auf 0,00 ±0,05 Vs-s einstellen. Hierfür die Regelschalter oder die Tasten auf der Fernbedienung betätigen. (wie bei 100% Weißpegel) 100% Weiß Rot 1. Das PAL-Farbbalkensignal » Die Differenz (100%) des Weiß- und Rotanteils auf PALzuführen. 0,2 ±0,05 Vs-s einstellen. Hierfür die Regelschalter Farbsättigungspegel Gruppe : VIDEO 1 oder die Tasten auf der Fernbedienung betätigen. Gegenstand : P-COLOR 100% Weiß Rot 2. Das Oszilloskop am Stift(1) von P801 anschließen. 71 XG-C40XU/XE Nr. Einstellposition Einstellbedingung Einstellverfahren 21 1. Das SECAM» Die Daten-Differenz (100%) des Weiß- und SECAMFarbbalkensignal zuführen. Rotanteils auf 0,2 ±0,05 Vs-s einstellen. Hierfür Farbsättigungspegel Gruppe : VIDEO 1 die Regelschalter oder die Tasten auf der Gegenstand : S-COLOR Fernbedienung betätigen. 2. Das Oszilloskop am Stift(1) 100% Weiß Rot von P801 anschließen. 22 Einstellung der 1. Das NTSC-10-Stufensignal » R1-GAIN wählen, dann die Amplitude des zuführen. R-Signals und die Amplitude des G-Signals auf Signal-Amplitude 2. Die Gruppe und den den gleichen Wert einstellen. des Gegenstand wählen: » Die gleiche Einstellung für das blaue Signal Video-Eingabefelds Gruppe: VIDEO2 vornehmen. Gegenstand: R1-GAIN B1-GAIN 3. Das Oszilloskop mit TP1101 (R) und TP1201 (G) verbinden. 4. Für Blau das Oszilloskop mit TP1301 (B) und TP1201 (G) verbinden. 23 VideoWelßbalance 1. Das NTSCMonoskopsignal zuführen. Gruppe : VIDEO 2 Gegenstand : R1-BLK B1-BLK » Mit den Regelschaltern am Gerät oder über die Fernbedienung die Einstellung so vornehmen, daß die gesamte Bildschirmfläche gleichmäßig unbunt erscheint. 24 Einstellung des DTV-Weißabgleichs 1. Das Monoskopmuster-Signal zuführen. 2. Gruppe: DTV Gegenstand: CR-OFFSET CB-OFFSET » Mit den Regelschaltern am Gerät oder über die Fernbedienung die Einstellung so vornehmen, daß die gesamte Bildschirmfläche gleichmäßig unbunt erscheint. 25 Setup 1. Gruppe: VIDEO1 Gegenstand: SET UP B SET UP C » Sich vergewissern, daß die Einstellungen wie folgt vorgenommen wurden: 11 für SET UP B, und 2 für SET UP C. 26 Automatische Farbkorrektur 1. Unter Verwendung des automatischen Farbkorrektur-Systems (ccdc) die automatische Farbkorrektur vornehmen. » Sich vergewissern, daß am Bildschirm keine Farbabweichungen auftreten. 27 Leistungsprüfung 1. Das Farbbalkensignal empfangen. des Farbsystems 28 Leistungsprüfung des Videosystems » Im Verarbeitungsmodus L1 anwählen. Die Farbe und die Tönung überprüfen. » Im Verarbeitungsmodus L2 anwählen. Die Farbe und die Tönung überprüfen. 1. Das Monoskopsignal empfangen. 72 XG-C40XU/XE Nr. Einstellposition Einstellbedingung Einstellverfahren 29 Leistungsprüfung des Audiosystems » Im Verarbeitungsmodus L3 anwählen. Baß, Höhen und Balance überprüfen. 30 1. Das RGB-Signal RGBempfangen. Leistungsprüfung » Im Verarbeitungsmodus L4 anwählen. Bild, Helligkeit, Rot, Blau, Takt, Phase, Horizontal- und Vertikalposition überprüfen. 31 Leistungsprüfung Off-Timer » Im Verarbeitungsmodus OFF anwählen. Sicherstellen, daß der Off-Timer bei "5" (Minuten) beginnt, jede Minute in 1 sec Intervallen herunterzählt und das Gerät bei "0" ausschaltet. 32 1. Den Thermistor mit einem ThermistorFön erwärmen. Leistungsprüfung » Sicherstellen, daß "TEMP" angezeigt wird. 33 1. Das PHASEAutomatische Prüfmustersignal Synchronisierung empfangen. » Den VGA/SVGA/XGA/SXGA-Modus einschalten und sicherstellen, daß Taktung und Phase sowie Horizontal- und Vertikalposition automatisch einstellbar sind. 34 Leistungsprüfung für KeystoneKorrektur » Sicherstellen, daß die Keystone-Korrektur gut funktioniert. 35 Werkseinstellungen » Folgende Einstellungen durchführen: Verarbeitung Fernbedienungseinstellung seinstellung S3 "Werkseinstellung 3"(XG-C40XE) S4 "Werkseinstellung 4"(XG-C40XU) 73 XG-C40XU/XE EINSTELLUNG DER PC-PLATINE (CPCi-0047CE16. PC I/F Einheit) 1. RGB-Pegeleinstellung 1) Einen Signalgenerator an den Projektor anschließen (mit 0047-Platine bestückt). Den Signalgeneratorausgang in den XGA-Modus bringen (VESA 1024x768, 60 Hz, 32-Farbton-Wellenform). Die Ausgangsamplitude am Anschluß P8404 auf 700 mVs-s einstellen. 2) Den Projektoreingang in den RGB1-Modus bringen. 3) Den Verarbeitungsmodus durch Betätigen der Taste am Projektor abrufen. 4) „A/D“ am Hauptmenü-Bildschirm anwählen. 5) „R-BRIGHT“ in der „A/D“-Gruppe wählen und „R-BRIGHT“ so einstellen, daß sich keine sichtbaren Pixel rund um den Bildschirm bilden. 6) Die gleichen Einstellungen mit „G-BRIGHT“ und „B-BRIGHT“ durchführen. 7) Danach die „R-D“-Gruppe anwählen und die Einstellungen der obigen Posten so ausführen, daß sich keine sichtbaren Pixel rund um den Bildschirm bilden. 8) Nun die Gruppen „G-D“ und „B-D“ anwählen und die gleichen Einstellungen durchführen. Nun zur DTV-Pegeleinstellung weitergehen. 2. DTV-Pegeleinstellung 1) Den Signalgeneratorausgang auf den „nur Grün-Modus“ einstellen. 2) „DTV“ auf dem Hauptmenü-Bildschirm für den Verarbeitungsmodus anwählen. 3) Den Posten „G-BRIGHT“ in der „DTV“-Gruppe anwählen und die „G-BRIGHT“-Einstellung so durchführen, daß sich keine sichtbaren Pixel rund um den Bildschirm bilden. 4) Das gleiche mit den Einstellungen „CB-OFFSET“ und „CR-OFFSET“ ausführen. Die 0047-Platine im Projektor ist nun für die Auslieferung bereit. Hinweis: VIDEO-Eingangseinstellungen sind nicht erforderlich. Vorsichtshinweise zur Wartung Wenn sich bei Wartungsarbeiten am Gerät die Konvergenz verschiebt, den Prozeßmodus aufrufen und die nachfolgende Gruppe und Gegenstände wählen. Gruppe: NOKO Gegenstand: R-CNV-H, R-CNV-V G-CNV-H, G-CNV-V B-CNV-H, B-CNV-V (H und V repräsentieren die horizontalen bzw. vertikalen Einstellungen.) Die obigen Einstellungen in einem Bereich zwischen 0 und 4 vornehmen. 74 XG-C40XU/XE FEHLERSUCHTABELLE Überprüfung der Platinenleistung Gestörter Videoeingang Gestörte RGB-Eingabe Zum Abschnitt “Prüfung des Videoschaltkreises” weitergehen. Ein Mustersignal vom PC zuführen. Gestörter DurchgangsAusgang Gestörter DurchgangsAusgangsschaltkreis Wurde zwischen PC und Nein Projektor das vorgeschriebene Kabel angeschlossen? Ja Entspricht die Versorgungsspannung dem Sollwert? Ja Das spezifizierte Kabel verwenden. Nein Defekter Netzschaltkreis Erscheint das Bild? Nein Ja Die Anschlüsse überprüfen. Dabei am PCEingangsschaltkreis beginnen. Zum Abschnitt “Störungssuchtabelle für PCSchnittstelleneinheit” weitergehen. 75 Fernbedienungskabel defekt Zum Abschnitt “Überprüfung des FernbedienungsSchaltkreises” weitergehen. XG-C40XU/XE FEHLERSUCHTABELLE (Fortsetzung) Überprüfung des Videosystems Nein Leuchtet die Lampe? Ja Zum Abschnitt “Lampe leuchtet nicht auf” weitergehen. Wird die vorgeschriebene Spannung Nein den EA-Anschlüssen zugeführt? Ja Den Netzschaltkreis und seine zugehörigen Bauteile überprüfen. Nein Liegen Eingangssignale an den Stiften (3) und (29) von P402 an? Ja Liegen Signale am Stift (4) von IC401 und Stift (4) von IC402 an? Liegen Ausgangssignale an den Stiften (3) und (6) von IC816 an? Ja Ja Nein Zur "Überprüfung von IC801 (RGB-SignalAusgangsschaltkreis)" weitergehen. IC816, IC806 und ihre peripheren Schaltkreise sowie den UmschaltSchaltkreis überprüfen. Den Videoschaltkreis überprüfen (IC6004 und seine peripheren Schaltkreise). Überprüfung des Videoschaltkreises Liegt ein Video-Ausgangssignal am Stift (7) von IC6001 an? Nein Ja Liegt ein Video-Eingangssignal am IC6004 an? Den IC6001-Wahlschalter, die Anschlußspannung und den Eingangsschaltkreis überprüfen. Nein Ja Liegen Ausgangssignale an den Stiften (6) und (8) von IC6004 an? Die Tiefpaß- und PufferspeicherSchaltkreise von Q6009 bis Q6015 überprüfen. Nein Ja Die Tiefpaß- und PufferspeicherSchaltkreise von Q6002 bis Q6008 überprüfen. Ja IC6004 seine peripheren Schaltkreise (Vorspannung) überprüfen. Nein Q6002 bis Q6008 und ihre peripheren Schaltkreise überprüfen. Zur “Überprüfung von IC801 (RGBSignal-Ausgangsschaltkreis)” weitergehen. 76 Nein Den Schwingungsschaltkreis von IC401 und IC402 und seine peripheren Schaltkreise überprüfen. XG-C40XU/XE FEHLERSUCHTABELLE (Fortsetzung) Überprüfung des IC801 (RGB-Signal-Ausgangsschaltkreis) Nein Zum Abschnitt “Keine Farbe oder ungewöhnlicher Farbton”, “Kein YSignal” oder “Keine Synchronisation” weitergehen. Nein Liegen RGBAusgangswellenformsignale an der Stiften (31), (32) und (33) von IC801 an? Ja Liegen Ausgangswellenformsignale an den Emittern von Q1501, Q1502 und Q1503 an? Nein Q1501 bis Q1503, SC1501 und ihre peripheren Schaltkreise überprüfen. Ja Liegen Ausgangswellenformsignale an den Emittern von Q1505, Q1506 und Q1507 an? Ja Den Datentransfer und andere Funktionen an den Stiften (17) und (18) des Video-IC801 überprüfen. Nein IC1501, Q1505 bis Q1507 und ihre peripheren Schaltkreise überprüfen. Zum Abschnitt “Störungssuchtabelle für PC-Schnittstelleneinheit” weitergehen. Überprüfung der Chroma- und Y-Signale des IC801 (RGB-Signalausgabe) Liegen Eingangssignale an den Stiften (12) (Y-Signal) und (19) (Chroma-Signal) von P402 an? Nein Zum Abschnitt “Überprüfung des Videoeinheit-Schaltkreises” weitergehen. Ja Liegen Ausgangs-Wellenformsignale Nein an den Stiften (3) (Chroma-Signal) und (6) (Y-Signal) von IC816 an? Die IC816-Schaltfunktion und ihre peripheren Schaltkreise überprüfen. Wenn an den Stiften (9) und (1) von IC816 kein Signale anliegen, den 3D-Störungsreduzierschaltkreis (IC806) überprüfen. Ja Liegen Eingangssignale an den Stiften (20) (Chroma-Signal) und (21) (Y-Signal) von IC801 an? Ja Nein IC801 und seine peripheren Schaltkreise überprüfen. Zum Abschnitt “Überprüfung des IC801 (RGB-AusgangssignalSchaltkreis)” weitergehen. 77 IC806 (3-D Entstör-Schaltkreis) und seine peripheren Schaltkreise überprüfen. XG-C40XU/XE FEHLERSUCHTABELLE (Fortsetzung) Überprüfung des IC806 (3-D Störungs-Reduzierschaltkreis) und seiner peripheren Schaltkreise Liegen Eingangssignale an den Stiften (40) (Y-Signal) und (45) (Chroma-Signal) von IC806 an? Nein Den Pufferspeicher-Schaltkreis von Q814 bis Q816 sowie Q903 bis Q906 überprüfen. Ja Liegen Ausgangssignale an den Stiften (55) (Y-Signal) und (51) (Chroma-Signal) von IC806 an? Nein Ja Liegen Ausgangssignale an den Emittern von Q817 (Y-Signal) und Q910 (Chroma-Signal) an? IC806, IC807 (Speicher) und seine peripheren Schaltkreise überprüfen. Nein Ja Den Tiefpaß-Schaltkreis rund um Q817, Q907 und Q910 überprüfen. IC816 und IC801 (RGBAusgangssignal-Schaltkreis) überprüfen. Keine Farbe oder ungewöhnlicher Farbton (NTSC, PAL) Liegen Chroma-Ausgangssignale am Nein Stift (20) von IC801 an? Ja Liegen Ausgangssignale an den Stiften (46)(R-Y) und (45)(B-Y) von IC801 an? Ja Zum Signalverarbeitungsblock zurückkehren. Nein Die Schwingung von X801 und X802 und ihre peripheren Schaltkreise überprüfen. IC803, IC814 und ihre peripheren Schaltkreise überprüfen. 78 XG-C40XU/XE FEHLERSUCHTABELLE (Fortsetzung) Kein oder ungewöhnliches Y-Signal Liegen Y-Eingangssignale am Stift (21) von IC801 an? Nein Ja Liegen Y-Ausgangssignale am Stift (40) von IC801 an? Zum Signalverarbeitungsblock zurückkehren. Nein Ja Liegen Y-Ausgangssignale am Stift (17) von IC803 an? IC801 und seine peripheren Schaltkreise überprüfen. Nein Ja IC803 und seine peripheren Schaltkreise überprüfen, sowohl als auch IC805 (AGC). IC803 und seine peripheren Schaltkreise überprüfen. Keine oder ungewöhnliche Horizontal-Synchronisation Liegen HorizontalsynchronAusgangssignale am Stift (56) von IC801 an? Ja Nein Liegen HorizontalsynchronAusgangssignale am Stift (9) von IC603 an? Ja Nein IC801 und seine peripheren Schaltkreise überprüfen. Den Impulsbildungs-Schaltkreis von IC602 und IC603 überprüfen. IC604 und seine peripheren Schaltkreise überprüfen und zur “Störungssuchtabelle für die PCSchnittstelleneinheit” weitergehen. Keine oder ungewöhnliche Vertikal-Synchronisation Liegen VertikalsynchronAusgangssignale am Stift (4) von IC801 an? Nein Ja IC801 und seine peripheren Schaltkreise überprüfen. IC604 und seine peripheren Schaltkreise überprüfen und zur “Störungssuchtabelle für die PCSchnittstelleneinheit” weitergehen. 79 XG-C40XU/XE FEHLERSUCHTABELLE (Fortsetzung) Überprüfung der Ausgangsplatine Nein Wenn keine Signale am SC1501 und SC1502 anliegen, zu Video-Systemblock weitergehen. Wenn keine Signale am SC1404 und SC1405 anliegen, zur “Störungssuchtabelle für die PC-Schnittstelleneinheit” weitergehen. Liegen Eingangssignale an Nein SC1404, SC1405, SC1501 und SC1502 an? Wird den EA-Steckverbindern Wenn keine Signale am EAund SC5502 Spannung Steckverbinder oder SC5502 zugeführt? anliegen, zum Abschnitt Ja “Überprüfung des Netzteilblocks” weitergehen. Liegen Ausgangssignale an den Stiften (14), (16) und (18) von IC1401 an? Nein Ja Liegen Eingangssignale am Stift (47) von IC1101, IC1201 und IC1301 an? IC1401 und ihre peripheren Schaltkreise überprüfen. Nein Ja IC1401 und ihre peripheren Schaltkreise überprüfen. Liegen Ausgangssignale an Nein den Stiften (17), (19), (21), (28), (30) und (32) von IC1101, IC1201 und IC1301 an? Ja IC1101, IC1201 und IC1301 und ihre peripheren Schaltkreise überprüfen. Liegen Ausgangssignale an Nein den Stiften (17), (19), (21), (28), (30) und (32) von IC1102, IC1202 und IC1302 an? Ja Nein Wenn keine Eingangssignale an den Stiften (1) und (31) von SC1101, SC1102 und SC1103 anliegen, den UmschaltSchaltkreis und den Verstärkerschaltkreis von IC1101, IC1201, IC1301, IC1102, IC1202, IC1302 und ihre peripheren Schaltkreise überprüfen. Liegen Eingangssignale an Nein SC1101, SC1201 und SC1301 an? Yes Ja Die R-, G- und B-Platinen überprüfen. IC1102, IC1202 und IC1302 und ihre peripheren Schaltkreise überprüfen. Wenn keine Eingangssignale an den Stiften (15) und (30) von SC1101, SC1102 und SC1103 anliegen, IC1409 und ihre peripheren Schaltkreise überprüfen. IC1106, IC1206, IC1306, IC1408 und ihre peripheren Schaltkreise überprüfen. 80 XG-C40XU/XE FEHLERSUCHTABELLE (Fortsetzung) Kein Ton Liegen Audio-Eingangssignale an Stift (2) von IC1411 an? Nein Den Eingangskreis und den Umschalt-Schaltkreis von IC3303 und IC3304 und ihre peripheren Schaltkreise, SC3001, SC1502 usw. überprüfen. Ja Liegen Audio-Eingangssignale an Stift (2) von P5508 an? Nein Ja Bei IC1411 die Steuerspannung und die peripheren Schaltkreise überprüfen. Liegen Audio-Eingangssignale an Stift (6) von IC7301 an? Nein Ja IC7301 überprüfen und seine peripheren Schaltkreise überprüfen. IC7301 und seine peripheren Schaltkreise sowie die SPSteckverbinder und Lautsprecher überprüfen. Wenn die Spannung am Stift (2) von IC7301 nicht dem Sollwert entspricht, Q5501, Q5502 und seine peripheren Schaltkreise überprüfen. Überprüfung des Netzgeräts Am EA-Steckverbinder liegt keine Ausgangsspannung an. Ja Besteht ein anderes AusgangsspannungsVersagen? Nein Welche Ausgangsspannungsleitung ist defekt? 6.7V Ist der EA-Steckverbinder abgezogen oder locker? Ja Nein ICP751 ersetzen. Den EA-Steckverbinder wieder anschließen. Liegen am PA-Steckverbinder 85 bis 264V Netzspannung an? Nein Ja F701 ersetzen oder den Bimetall-SW überprüfen. Ja Ist der TF701 offen? Nein TF701 ersetzen. Ist der R706 open? Nein Ja R700 ersetzen. Die Leistungseinheit ersetzen. 81 XG-C40XU/XE FEHLERSUCHTABELLE (Fortsetzung) Gerät eingeschaltet Wurde der korrekte Eingang gewählt? Nein Ja Den korrekten Eingang mit der Fernbedienung anwählen Entsprechen die PC-, Video- und LCP-Kabel den Spezifikationen und sind diese richtig angeschlossen? Ja Nein Erscheint das Bild bei maximaler Einstellung des Kontrastreglers? Ja Die korrekten Kabel benutzen oder erneut anschließen Nein Das Videosystem nachjustieren. Nein Entspricht die Spannung am CON3 (P8502) Steckverbinder dem Sollwert? Ja Netzschaltkreis defekt. Einen PC anschließen. Erscheint das Bild? Nein Ja Entspricht das Bild dem Sollwert? A Zum Abschnitt “Überprüfung des Taktschaltkreises und seiner peripheren Schaltkreise” weitergehen. Nein Ja Entspricht die Bildfarbe dem Sollwert? Den Synchron-Signalschaltkreis und seine peripheren Schaltkreise überprüfen. Nein Ja Funktioniert die Bildschirmanzeige? Den Videoschaltkreis und seine peripheren Schaltkreise überprüfen. Nein Ja Funktioniert die Fernbedienung? Nein Ja Zum Abschnitt “Überprüfung des OSD-Schaltkreises und seiner peripheren Schaltkreise” weitergehen. Zum Abschnitt “Überprüfung der Fernbedienung” weitergehen. Ende 82 XG-C40XU/XE FEHLERSUCHTABELLE (Fortsetzung) Die Lampe leuchtet nicht Ja Den Netzschalter einschalten. Wird in der Lampe ein Entladegeräusch erzeugt? Nein Sitzt die Lampe nicht in ihrer Fassung? Ja Nein Läuft das Ballast-Kühlgebläse? Die Lampe wieder in die Fassung einsetzen. Nein Ja Die Lampe ersetzen. Den Netzschaltkreis überprüfen. Werden zwischen den Stiften des PL-Steckverbinders 360 V Gleichspannung zugeführt? Nein Ja Ja Werden zwischen des Stiften (1) und (2) des Ballast-DSteckverbinders 2 V oder eine höhere Spannung zugeführt? Nein Den Ballast ersetzen. Ist der D-Steckverbinder abgetrennt? Ja Den Steckverbinder wieder anschließen. Nein Den MikrocomputerSchaltkreis überprüfen. 83 XG-C40XU/XE FEHLERSUCHTABELLE FÜR PC I/F EINHEIT-1 Gerät eingeschaltet Wurde der richtige Eingang gewählt? Nein Die spezifizierte Eingabe mit der Fernbedienung anwählen. Nein Die empfohlenen Kabel benutzen und korrekt anschließen. Ja Sind die Kabel für PC, Video und Projektor korrekt angeschlossen? Ja Den Kontrast ganz aufdrehen. Ist das Bild sichtbar? Ja Die Videoeinstellungen nachjustieren. Nein Ist die Spannung am P8502Steckverbinder wie spezifiziert? Ja Ist das Bild sichtbar? Nein Defekter Stromkreis. Ja Zum Abschnitt "Überprüfung des Taktschaltkreises und seiner peripheren Schaltkreise" weitergehen. Ja Zum Abschnitt "Überprüfung des Synchronsignal-Schaltkreises und seiner peripheren Schaltkreise" weitergehen. Ja Zum Abschnitt "Überprüfung des Videoschaltkreises und seiner peripheren Schaltkreise" weitergehen. Ja Zum Abschnitt "Überprüfung des OSD-Schaltkreises und seiner peripheren Schaltkreise" weitergehen. Ja Zum Abschnitt "Überprüfung der Fernbedienung" weitergehen. Nein Bestehen Bildstörungen? Nein Sind die Bildfarben abnormal? 4 Nein Ist die Bildschirmanzeige gestört? Nein Ist die Fernbedienung gestört? Nein Ende 84 XG-C40XU/XE FEHLERSUCHTABELLE FÜR PC I/F EINHEIT-2 Den Taktschaltkreis und die zugehörigen Peripherieschaltkreise überprüfen. Erzeugt der X8001 (6MHz) Schwingungen? Nein X8001 oder ihre periphere Schaltung defekt. Nein X8003 oder ihre periphere Schaltung defekt. Nein X8004 oder ihre periphere Schaltung defekt. Nein X8005 oder ihre periphere Schaltung defekt. Nein IC8001 oder ihre periphere Schaltung defekt. Ja Erzeugt der X8003 (1,84MHz) Schwingungen? Ja Erzeugt der X8004 (22,165MHz) Schwingungen? Ja Erzeugt der X8005 (18,75MHz) Schwingungen? Ja Funktioniert Stift (162) von IC8001? Ja 5 85 XG-C40XU/XE FEHLERSUCHTABELLE FÜR PC I/F EINHEIT-3 Überprüfung des Synchronsignal-Schaltkreises und seiner peripheren Schaltkreise. 5 Nein Wird ein geteiltes Synchronisationssignal übermittelt? Ja Nein Liegen Signale an TP8004 und TP8005 an? Defekter IC8610 oder defekte Anschlußplatine. Ja Nein Ist das übermittelte Synchronisationssignal ein Grün-Sync-Signal? Ja Nein Liegt ein Signal am Stift (7) von IC8611 an? IC8611 oder ihre periphere Schaltung defekt. Ja Nein Liegen Signale an den Stiften (149) (TL8034) und (150) (TL8035) von IC8020 an? Ja Nein IC8025 oder ihre periphere Schaltung defekt. Weist das Eingangssignal eine niedrigere Auflösung als der XGAStandard auf, oder handelt es sich um ein Video-Eingangssignal? Ja Nein Liegen Signale an den Stiften (26) (TL8043), (28) (TL8041) und (29) (TL8042) von IC8020 an? IC8020 oder ihre periphere Schaltung defekt. Ja Nein Liegen an den Stiften (13) bis (52) des P8405 (außer Masse) Signale an? Ja 6 86 IC8029, IC8609 oder seine peripheren Bauteile defekt. XG-C40XU/XE FEHLERSUCHTABELLE FÜR PC I/F EINHEIT-4 Den PLL-Schaltkreis und die zugehörigen Peripherieschaltkreise überprüfen. 6 Liegen Signale an den Stift (111) und Nein (112) von IC8606 an? Ja Liegen Signale an den Stift (7) und (10) von IC8601 an? IC8025, IC8600 oder sein peripherer Schaltkreis defekt. Nein Ja IC8601, IC8606 oder sein peripherer Schaltkreis defekt. Den Videoschaltkreis und seine peripheren Schaltkreise überprüfen. Entspricht das Bild dem Sollwert bei e Nein iner Auflösung über dem XGA-Pegel? Den S-XGA-Videoschaltkreis und seine peripheren Schaltkreise überprüfen. Ja Entspricht das Bild dem Sollwert bei einer Auflösung unter dem XGA-Pegel? Nein Den VGA-Videoschaltkreis und seine peripheren Schaltkreise überprüfen. Ja Nein Ein Videosystem anschließen. Entspricht die Anzeige dem Sollwert? Ja Den Video-Systemschaltkreis und seine peripheren Schaltkreise überprüfen. 4 87 XG-C40XU/XE FEHLERSUCHTABELLE FÜR PC I/F EINHEIT-5 Überprüfung für SXGA-Videoschaltkreis (Rot) und seine Peripherieschaltkreise Liegt ein Signal am Stift (139) von IC8606 an? Überprüfung für VGAVideoschaltkreis (Rot) und seine Peripherieschaltkreise Nein Nein Liegt ein Signal am Stift (139) von IC8606 an? Ja Ja Die Anschlußplatine, C8616 sind defekt. Liegen an den Stiften (21) bis (31) sowie an den Stiften (34) bis (41) des P8606 (außer Masse) Signale an? Nein IC8606 oder ihre periphere Schaltung defekt. Ja Liegen Signale an TL8044 und TL8046 an? Nein Ja Nein Liegen an den Stiften (21) bis (31) sowie an den Stiften (34) bis (41) des P8606 (außer Masse) Signale an? Ja Nein Liegen Signale an den Stiften (112) bis (119) von IC8020 an? Ja IC8025 oder ihre periphere Schaltung defekt. Nein Liegen Signale an den Stiften (69) bis (73) und (189) bis (192) von IC8020 an? Ja IC8020 oder ihre periphere Schaltung defekt. Liegt ein Signal am Stift (Y11)(TL8612) Nein von IC8609 an? Ja Liegen Signale an den Stiften (1) bis (10) von IC8051 an? Ja IC8029 oder ihre periphere Schaltung defekt. Nein IC8609 oder ihre periphere Schaltung defekt. Überprüfung für VideosystemSchaltkreis (Rot) und seine IC8501 oder sein peripherer Schaltkreis bzw. seine Ausgangsplatine defekt. Nein Liegt ein Signal am Stift (141) von IC8606 an? Ja C8702 oder sein peripherer Schaltkreis bzw. seine Signalplatine defekt. 1 88 1 XG-C40XU/XE FEHLERSUCHTABELLE FÜR PC I/F EINHEIT-6 Überprüfung für SXGA-Videoschaltkreis (Grün) und seine Peripherieschaltkreise Liegt ein Signal am Stift (124) von IC8606 an? Überprüfung für VGAVideoschaltkreis (Grün) und seine Peripherieschaltkreise Nein Nein Liegt ein Signal am Stift (124) von IC8606 an? Ja Ja Die Anschlußplatine, C8620 sind defekt. Liegen an den Stiften (68) bis (75) sowie an den Stiften (78) bis (88) des P8606 (außer Masse) Signale an? Nein Ja Liegen Signale an TL8045 und TL8047 an? IC8606 oder ihre periphere Schaltung defekt. Nein Ja Nein Liegen an den Stiften (68) bis (75) sowie an den Stiften (78) bis (88) des P8606 (außer Masse) Signale an? Ja Nein Liegen Signale an den Stiften (165) bis (177) von IC8020 an? Ja IC8025 oder ihre periphere Schaltung defekt. Nein Liegen Signale an den Stiften (178) bis (187) von IC8020 an? Ja IC8020 oder ihre periphere Schaltung defekt. Liegt ein Signal am Stift (V13)(TL8613) Nein von IC8609 an? Ja Liegen Signale an den Stiften (11) bis (20) von IC8051 an? Ja IC8029 oder ihre periphere Schaltung defekt. Nein IC8609 oder ihre periphere Schaltung defekt. Überprüfung für VideosystemSchaltkreis (Grün) und seine IC8501 oder sein peripherer Schaltkreis bzw. seine Ausgangsplatine defekt. Nein Liegt ein Signal am Stift (126) von IC8606 an? Ja C8703 oder sein peripherer Schaltkreis bzw. seine Signalplatine defekt. 1 89 1 XG-C40XU/XE FEHLERSUCHTABELLE FÜR PC I/F EINHEIT-7 Überprüfung für SXGA-Videoschaltkreis (Blau) und seine Peripherieschaltkreise Liegt ein Signal am Stift (133) von IC8606 an? Überprüfung für VGAVideoschaltkreis (Blau) und seine Peripherieschaltkreise Nein Nein Liegt ein Signal am Stift (133) von IC8606 an? Ja Ja Die Anschlußplatine, C8623 sind defekt. Liegen an den Stiften (45) bis (53) sowie an den Stiften (56) bis (64) des P8606 (außer Masse) Signale an? Nein Ja Liegen Signale an TL8048 und TL8049 an? IC8606 oder ihre periphere Schaltung defekt. Nein Ja Nein Liegen an den Stiften (45) bis (53) sowie an den Stiften (56) bis (64) des P8606 (außer Masse) Signale an? Ja Nein Liegen Signale an den Stiften (85) bis (93) von IC8020 an? Ja IC8025 oder ihre periphere Schaltung defekt. Nein Liegen Signale an den Stiften (74) bis (83) von IC8020 an? Ja IC8020 oder ihre periphere Schaltung defekt. Liegt ein Signal am Stift (U15)((TL8614) Nein von IC8609 an? Ja Liegen Signale an den Stiften (21) bis (30) von IC8051 an? Ja IC8029 oder ihre periphere Schaltung defekt. Nein IC8609 oder ihre periphere Schaltung defekt. Überprüfung für VideosystemSchaltkreis (Blau) und seine IC8501 oder sein peripherer Schaltkreis bzw. seine Ausgangsplatine defekt. Nein Liegt ein Signal am Stift (136) von IC8606 an? Ja C8704 oder sein peripherer Schaltkreis bzw. seine Signalplatine defekt. 1 90 1 XG-C40XU/XE FEHLERSUCHTABELLE FÜR PC I/F EINHEIT-8 Überprüfung für OSD-Schaltkreis und seiner Peripherieschaltkreise OSD-Anzeige auf dem Bildschirm. Liegen Signale an den Stiften (56), (58), (71) und (72) von IC8048 an? (TL8054,TL8053,TL8052,TL8051) Nein Ja Liegen Signale an den Stiften (12), (14) bis (17) und (20) von IC8046 an? IC8029 fehlerhaft oder zugehörige periphere Schaltkreise defekt. Nein Ja Liegen Signale an den Stiften (23) bis (42) von IC8046 an? IC8048 fehlerhaft oder zugehörige periphere Schaltkreise defekt. Nein Ja IC8046 oder deren Peripheriekreise defekt. IC8048 fehlerhaft oder zugehöriger peripherer Schaltkreis defekt. Überprüfung der Fernbedienung Die Fernbedienung verwenden. Liegt ein Signal am Stift (59) des P8405 an? Nein Ja Ausgabe-PWB defekt. IC8001 Schaltkreis defekt. 91 XG-C40XU/XE XG-C40XU/XE CHASSIS LAYOUT / CHASSIS-ANORDNUNG H G F E D C B A 1 2 3 4 5 6 92 7 8 9 10 11 12 13 14 15 93 16 17 18 19 XG-C40XU/XE XG-C40XU/XE BLOCK DIAGRAM / BLOCKSCHALTBILD H G F E D C B A 1 2 3 4 5 6 94 7 8 9 10 11 12 13 14 15 95 16 17 18 19 XG-C40XU/XE XG-C40XU/XE OVERALL WIRING DIAGRAM / GESAMTSCHALTPLAN H G F E D C B A 1 2 3 4 5 6 96 7 8 9 10 11 12 13 14 15 97 16 17 18 19 XG-C40XU/XE DESCRIPTION OF SCHEMATIC DIAGRAM BESCHREIBUNG DES SCHEMATISCHEN SCHALTPLANS H VOLTAGE MEASUREMENT CONDITION: SPANNUNGSMESSUNGEN: 1. Voltages at test points are measured at the supply voltage of AC 230V. Signals are fed by a colour bar signal generator for servicing purpose and the above voltages are measured with a 20k ohm/V tester. 1. Spannungen an den Prüfpunkten werden bei einer Netzspannung von 230V gemessen, Signale werden für die Wartung mit einem Farbbalken-Signal generator zugeführt, und Spannungen werden mit einem Meßinstrument (20 kΩ/V) ermittelt. G WAVEFORM MEASUREMENT CONDITION: SIGNALFORMMESSUNGEN: 1. Waveforms at test points are observed at the supply voltage of AC 230V. Signals are fed by a colour bar signal generator for servicing purpose. 1. Die Wellenformen an den Testpunkten werden bei einer Netzspannung von 230V verfolgt. Signale werden für die Wartung mit einem Farbbalken-Signal generator zugeführt. INDICATION OF RESISTOR & CAPACITOR: BEZEICHNUNG DES WIDERSTANDS UND KONDENSATORS: F RESISTOR 1. The unit of resistance “Ω” is omitted. (K=kΩ=1000 Ω, M=MΩ). 2. All resistors are ± 5%, unless otherwise noted. (J= ± 5%, F= ± 1%, D= ± 0.5%) 3. All resistors are 1/16W, unless otherwise noted. 4. All resistors are Carbon type, unless otherwise E noted. W : Cement C : Solid S : Oxide Film T : Special N : Metal Coating CAPACITOR 1. All capacitors are µF, unless otherwise noted. (P=pF=µµF). 2. All capacitors are 50V, unless otherwise noted. D 3. All capacitors are Ceramic type, unless otherwise noted. (ML): Mylar (TA): Tantalum (PF): Polypro Film (ST): Styrol WIDERSTAND 1. Die Widerstandseinheit “Ω” wird weggelassen. (K=kΩ=1000 Ω, M=MΩ). 2. Alle Widerstände haben ± 5%, sofern nicht anders angegeben. (J= ± 5%, F= ± 1%, D= ± 0.5%) 3. Alle Widerstände haben 1/16W, sofern nicht anders angegeben. 4. Alle Widerstände sind Kohletyp, sofern nicht anders angegeben. W : Zement C : Fest S : Oxidefilm T : Spezial N : Metallüberzug KONDENSATOR 1. Die Kapazitätseinheit ist µF, sofern nicht anders angegeben. (P=pF=µµF). 2. Alle Kondensatoren haben 50V, sofern nicht anders angegeben. 3. Alle Kondensatoren sind Keramiktyp, sofern nicht anders angegeben. (ML): Mylar (TA): Tantal (PF): Polyprofilm (ST): Styrol CAUTION: CThis circuit diagram is original one, therefore there may be a slight difference from yours. ACHTUNG: bei diesem Schaltplan handelt es sich um den ursprünglichen. Esönnen daher geringfügige Unterschiede zu dem lhrem bestehen. SAFETY NOTES: 1. DISCONNECT THE AC PLUG FROM THE AC OUTLET BEFORE REPLACEING PARTS. 2. SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS POTENTIAL SHOCK HAZARDS B WHEN THE CHASSIS IS OPERATING. SICHERHEITSANMERKUNGEN: 1. VOR DEM AUSWECHSELN VON TEILEN MUSS UNBEDINGT NETZSTECKER AUS DER NETZSTECKDOSE GEZOGEN WERDEN. 2. DIE WARMEABLEITER DER HALBLEITER SOLLTEN BEIM BETRIEB DES CHASSIS ALS MÖGLICHE URSACHEN VON GEFÄHRLICHEN ELEKTRISCHEN SCHLÄGEN BETRACHTET WERDEN. IMPORTANT SAFETY NOTICE: PARTS MARKED WITH “ å ( ) ARE IMPORTANT FOR MAINTAINING THE SAFETY OF THE SET. BE SURE TO REPLACE THESE PARTS AWITH SPECIFIED ONES FOR MAINTAINING THE SAFETY AND PERFORMANCE OF THE SET. 1 2 3 4 WICHTIGE SICHERHEITSANMERKUNGEN: MIT “å ( )BEZEICHNETEN TEILE SIND BESONDERS WICHTIG FÜR DIE AUFRECHTERHALTUNG DER SICHERHEIT . BEIM WECHDIESER TEILE SOLLTEN DIE VORGESCHRIEBENEN TEILE IMMER VERWENDET WERDEN, UM SOWOHL DIE SICHERHEIT ALS AUCH DIE 6 7 8 9 10 LEISTUNG DES GERÄTES AUFRECHTZUERHALTEN. 5 98 XG-C40XU/XE WAVEFORMS / WELLENFORMEN 1 SC1101 18-pin 2 SC1101 19-pin (RP SIG5) H : 10µsec/div V : 2V/div (RP SIG6) H : 10µsec/div V : 2V/div 5 SC1301 18-pin 7 P801 1-pin (BP SIG6) H : 10µsec/div V : 2V/div 9 P801 4-pin 8 P801 2-pin (R) H : 10µsec/div V : 0.5V/div 0 IC604 6-pin (B-Y) H : 20µsec/div V : 1V/div (GP SIG6) H : 10µsec/div V : 2V/div (GP SIG5) H : 10µsec/div V : 2V/div 6 SC1301 19-pin (BP SIG5) H : 10µsec/div V : 2V/div 4 SC1201 19-pin 3 SC1201 18-pin (G) H : 20µsec/div V : 0.5V/div q Q422 Emitter (H-OUT) H : 20µsec/div V : 1V/div w Q6008 Emitter (4FSC) H : 50µsec/div V : 0.5V/div (Y-signal) H : 10µsec/div V : 0.2V/div e Q6003 Emitter (CHROMA signal) H : 10µsec/div V : 0.2V/div 10 11 12 13 14 15 99 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë SIGNAL UNIT-1/2 / SIGNALEINHEIT-1/2(XG-C40XU) H G F E D C B A 1 2 3 4 5 100 6 7 8 9 10 11 12 13 14 15 101 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë SIGNAL UNIT-2/2 / SIGNALEINHEIT-2/2(XG-C40XU) H G F E D C B A 1 2 3 4 5 102 6 7 8 9 10 11 12 13 14 15 103 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë SIGNAL UNIT-1/2 / SIGNALEINHEIT-1/2(XG-C40XE) H G F E D C B A 1 2 3 4 5 104 6 7 8 9 10 11 12 13 14 15 105 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë SIGNAL UNIT-2/2 / SIGNALEINHEIT-2/2(XG-C40XE) H G F E D C B A 1 2 3 4 5 106 6 7 8 9 10 11 12 13 14 15 107 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë PC TERMINAL UNIT / PC-ANSCHLUßEINHEIT(XG-C40XU) H G F E D C B A 1 2 3 4 5 108 6 7 8 9 10 11 12 13 14 15 109 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë PC TERMINAL UNIT / PC-ANSCHLUßEINHEIT(XG-C40XE) H G F E D C B A 1 2 3 4 5 110 6 7 8 9 10 11 12 13 14 15 111 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë SOUND OUT and REGULATOR UNIT / TONAUSGABE-und REGLEREINHEIT H G F E D C B A 1 2 3 4 5 112 6 7 8 9 10 11 12 13 14 15 113 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë OUTPUT UNIT-1/6 / AUSGABEEINHEIT-1/6 H G F E D C B A 1 2 3 4 5 114 6 7 8 9 10 11 12 13 14 15 115 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë OUTPUT UNIT-2/6 / AUSGABEEINHEIT-2/6 H G F E D C B A 1 2 3 4 5 116 6 7 8 9 10 11 12 13 14 15 117 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë OUTPUT UNIT-3/6 / AUSGABEEINHEIT-3/6 H G F E D C B A 1 2 3 4 5 118 6 7 8 9 10 11 12 13 14 15 119 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë OUTPUT UNIT-4/6 / AUSGABEEINHEIT-4/6 H G F E D C B A 1 2 3 4 5 120 6 7 8 9 10 11 12 13 14 15 121 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë OUTPUT UNIT-5/6 / AUSGABEEINHEIT-5/6 H G F E D C B A 1 2 3 4 5 122 6 7 8 9 10 11 12 13 14 15 123 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë OUTPUT UNIT-6/6 / AUSGABEEINHEIT-6/6 H G F E D C B A 1 2 3 4 5 124 6 7 8 9 10 11 12 13 14 15 125 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë VIDEO UNIT / VIDEOEINHEIT H G F E D C B A 1 2 3 4 5 126 6 7 8 9 10 11 12 13 14 15 127 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë POWER and INLET UNIT / NETZ-und EINGANGSEINHEIT H G F E D C B A 1 2 3 4 5 128 6 7 8 9 10 11 12 13 14 15 129 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë PC I/F UNIT-1/9 / PC-I/F EINHEIT-1/9 H G F E D C B A 1 2 3 4 5 130 6 7 8 9 10 11 12 13 14 15 131 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë PC I/F UNIT-2/9 / PC-I/F EINHEIT-2/9 H G F E D C B A 1 2 3 4 5 132 6 7 8 9 10 11 12 13 14 15 133 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë PC I/F UNIT-3/9 / PC-I/F EINHEIT-3/9 H G F E D C B A 1 2 3 4 5 134 6 7 8 9 10 11 12 13 14 15 135 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë PC I/F UNIT-4/9 / PC-I/F EINHEIT-4/9 H G F E D C B A 1 2 3 4 5 136 6 7 8 9 10 11 12 13 14 15 137 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë PC I/F UNIT-5/9 / PC-I/F EINHEIT-5/9 H G F E D C B A 1 2 3 4 5 138 6 7 8 9 10 11 12 13 14 15 139 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë PC I/F UNIT-6/9 / PC-I/F EINHEIT-6/9 H G F E D C B A 1 2 3 4 5 140 6 7 8 9 10 11 12 13 14 15 141 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë PC I/F UNIT-7/9 / PC-I/F EINHEIT-7/9 H G F E D C B A 1 2 3 4 5 142 6 7 8 9 10 11 12 13 14 15 143 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë PC I/F UNIT-8/9 / PC-I/F EINHEIT-8/9 H G F E D C B A 1 2 3 4 5 144 6 7 8 9 10 11 12 13 14 15 145 16 17 18 19 XG-C40XU/XE XG-C40XU/XE Ë PC I/F UNIT-9/9 / PC-I/F EINHEIT-9/9 H G F E D C B A 1 2 3 4 5 146 6 7 8 9 10 11 12 13 14 15 147 16 17 18 19 XG-C40XU/XE PRINTED WIRING BOARD ASSEMBLIES/ LEITERPLATTENEINHEITEN H G F E Signal Unit (Wiring Side)/ Signaleinheit (Leiterbahnseite) (XG-C40XU) D C B Signal Unit (Wiring Side)/ Signaleinheit (Leiterbahnseite) (XG-C40XE) A 1 2 3 4 148 5 6 XG-C40XU/XE H G F E Signal Unit (Component Side)/ Signaleinheit (Bestückungsseite) (XG-C40XU) D C B Signal Unit (Component Side)/ Signaleinheit (Bestückungsseite) (XG-C40XE) A 1 2 3 4 149 5 6 XG-C40XU/XE H G PC Terminal Unit (Wiring Side)/ PC-Anschlußeinheit (Leiterbahnseite) (XG-C40XU) F E D PC Terminal Unit (Wiring Side)/ PC-Anschlußeinheit (Leiterbahnseite) (XG-C40XE) C B Video Unit (Wiring Side)/ Videoeinheit (Leiterbahnseite) A 1 2 3 4 150 5 6 XG-C40XU/XE H G PC Terminal Unit (Component Side)/ PC-Anschlußeinheit (Bestückungsseite) (XG-C40XU) F E D PC Terminal Unit (Component Side)/ PC-Anschlußeinheit (Bestückungsseite) (XG-C40XE) C B Video Unit (Component Side)/ Videoeinheit (Bestückungsseite) A 1 2 3 4 151 5 6 XG-C40XU/XE H G F E D C B A Output Unit (Wiring Side)/ Ausgabeeinheit (Leiterbahnseite) 1 2 3 4 152 5 6 XG-C40XU/XE H G F E D C B A Output Unit (Component Side)/ Ausgabeeinheit (Bestückungsseite) 1 2 3 4 153 5 6 XG-C40XU/XE H G F E PC I/F Unit (Wiring Side)/ PC-I/F-Einheit (Leiterbahnseite) D C B A PC I/F Unit (Component Side)/ PC-I/F-Einheit (Bestückungsseite) 1 2 3 4 154 5 6 XG-C40XU/XE H G F E Sound Out/Regulator Unit (Wiring Side)/ Tonausgabe/Reglereinheit (Leiterbahnseite) D C B A Sound Out/Regulator Unit (Component Side)/ Tonausgabe/Reglereinheit (Bestückungsseite) 1 2 3 4 155 5 6 XG-C40XU/XE H G F Power Unit (Wiring Side)/ Netzeinheit (Leiterbahnseite) E C B Power Unit (Component Side)/ Netzeinheit (Bestückungsseite) A 1 2 3 4 156 5 6 RDENC0334CEZZ LVR-INSW2742SH D XG-C40XU/XE H G F Inlet Unit (Wiring Side)/ Eingangseinheit (Leiterbahnseite) E D C B Inlet Unit (Component Side)/ Eingangseinheit (Bestückungsseite) A 1 2 3 4 157 5 6 XG-C40XU/XE Ref. No. ★ Part No. Description PARTS LIST Code Ref. No. Part No. ★ Description Code ERSATZTEILLISTE PARTS REPLACEMENT AUSTAUSCH VON TEILEN Replacement parts which have these special safety characteristics identified in this manual: electrical components having such features are identified by "å" in the Replacement Parts Lists. The use of a substitute replacement part which does not have the same safety characteristics as the factory recommended replacement parts shown in this service manual may create shock, fire or other hazards. Ersatzteile, die besondere Sicherheitseigenschften haben, sind in dieser Anleitung markiert. Elektrische Komponenten mit solchen Eigenshaften sind in den Ersatzteil durch "å" gekenn-zeichnet. Der Gebrauch von Ersatzteilen, die nicht deselben Sicherheitseigenschaften haben wie die vom Hersteller empfohlenen ud in der Bedienungsanleitung angegebenen, können zur Ursache von Blitzeinschlägen, Bränden und anderen Gefahren werden. "HOW TO ORDER REPLACEMENT PARTS" "WIE MAN ERSATSTEILE BESTELLT" To have your order filled promptly and correctly, please furnish the following informations. Damit Ihre Bestellung promt und korrekt ausgeführt wird, geben Sie bitte folgende Informationen. 1. MODEL NUMBER 2. REF. NO. 3. PART NO. 4. DESCRIPTION 5. CODE 6. QUANTITY 1. MODELL NR. 3. ERSATZTEIL NR. 5. KODE ★ MARK : SPARE PARTS-DELIVERY SECTION Ref. No. ★ Part No. Description ★ MARKIERUNG : ERSATZTEILE-LIEFERUNG Code Ref. No. Description Code INTEGRATED CIRCUITS PRINTED WIRING BOARD ASSEMBLIES (NOT REPLACEMENT ITEM) XG-C40XU DUNTKA211DE11 DUNTKA212DE11 DUNTKA693FE01 DUNTKA694FE01 DUNTK9769DE24 RUNTK0677CEZZ RDENC0334CEZZ CPCi-0047CE15 RDENC0333CEZZ – – – – – – – – J Signal Unit PC Terminal Unit S-Out/Regulater Unit Output Unit Video Unit AC Inlet Unit Power Unit PC I/F Unit Ballast Unit (Unit Replacement Item) — — — — — — — — PFiLD0076CEZZ RUNTK0673CEZZ J J Remote Mouse Receiver AE BM IC401 IC402 IC406 IC409 IC418 IC602 IC603 IC604 IC801 IC803 IC805 IC806 IC807 IC808 IC814 IC816 IC1001 VHiNJM2240M-1 VHiNJM2240M-1 VHiBA7046F/-1 VHiMM1041XM-1 VHiSN2G53CT-1 VHiTHC4538T-1 VHiTHC4538T-1 VHiSNHC153T-1 VHiTDA8854H-2 VHiTDA4565/-1 VHiNJM2060V-1 VHiTC90A11F-1 VHiM518221A-1 VHiPST600DM-1 VHiTA8814N/-1 VHiNJM2283V-1 VHiBA08SFP+-1 Q411 Q416 Q420 Q421 Q422 Q804 Q805 Q806 Q808 Q809 Q810 Q814 Q815 Q816 Q817 Q819 Q820 Q821 Q822 Q823 Q824 Q825 Q903 Q905 Q906 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC2411KR-1 VS2SC2411KR-1 VS2SC2411KR-1 VS2SA1530AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SA1530AR-1 VS2SA1530AR-1 VS2SC3928AR-1 VS2SA1530AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VSDTC144EK/-1 VS2SC3928AR-1 VS2SA1530AR-1 VSDTC114EK/-1 VS2SC2411KR-1 VS2SC2411KR-1 VS2SC2411KR-1 VS2SA1530AR-1 VS2SC3928AR-1 VS2SC3928AR-1 J J J J J J J J J J J J J J J J J NJM2240M NJM2240M BA7046F MM1041XMR SN74AHC2G53HDC Tc74Hc4538Aft Tc74Hc4538Aft SN74HC153PW TDA8854H/N2 TDA4565/V6 NJM2060V TC90A11F MSM518221A-30J IC-PSt600DMT TA8814N NJM2283V BA08SFP-E2 AG AG AF AG AE AL AL AK BD AN AF AZ AW AE AV AG AG TRANSISTORS XG-C40XE Signal Unit PC Terminal Unit S-Out/Regulater Unit Output Unit Video Unit AC Inlet Unit Power Unit PC I/F Unit Ballast Unit (Unit Replacement Item) ★ SIGNAL UNIT NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN ASSEMBLY BUT NOT INDEPENDENTLY. RLCDP0141CEZZ J LCD Module Unit, Red CT RLCDP0142CEZZ J LCD Module Unit, Green CT RLCDP0143CEZZ J LCD Module Unit, Blue CT – – – – – – – – J Part No. DUNTKA211DE11/B116DE02 LCD PANELS DUNTKB116DE02 DUNTKB117DE02 DUNTKA693FE02 DUNTKA694FE02 DUNTK9769DE25 RUNTK0677CEZZ RDENC0334CEZZ CPCi-0047CE16 RDENC0333CEZZ 2. REF. NR. 4. BESCHREIBUNG 6. QUANTITÄT — — — — — — — — 158 J J J J J J J J J J J J J J J J J J J J J J J J J 2SC3928AR 2SC3928AR 2SC2411KR 2SC2411KR 2SC2411KR 2SA1530AR 2SC3928AR 2SC3928AR 2SC3928AR 2SA1530AR 2SA1530AR 2SC3928AR 2SA1530AR 2SC3928AR 2SC3928AR DTC144EK 2SC3928AR 2SA1530AR DTC114EK 2SC2411KR 2SC2411KR 2SC2411KR 2SA1530AR 2SC3928AR 2SC3928AR AB AB AC AC AC AB AB AB AB AB AB AB AB AB AB AB AB AB AB AC AC AC AB AB AB XG-C40XU/XE Ref. No. ★ Part No. Description Code DUNTKA211DE11/B116DE02 SIGNAL UNIT (Continued) Q907 Q910 VS2SC3928AR-1 VS2SC3928AR-1 J 2SC3928AR J 2SC3928AR D801 D802 D803 D805 D1005 VHDMA152WA/-1 RH-EX0226CEZZ RH-EX0226CEZZ VHDDAN202K/-1 VHDDAN202K/-1 X801 X802 RCRSB0009PEZZ RCRSB0008PEZZ L904 L905 L906 L908 VP-1M330J4R2N VP-1M270J3R8N VP-1M330J4R2N VP-1M220J2R9N C404 C414 C416 C425 C437 C441 C443 C447 C448 C450 C451 C452 C453 C454 C455 C456 C458 C472 C485 C486 C487 C488 C489 C490 C491 C495 C601 C602 C603 C606 C607 C608 C609 C610 C611 C612 C613 C810 C811 C812 C814 C815 C816 C817 C818 C819 C822 C823 C824 C825 VCKYCY1EF104Z VCKYCY1HB103K VCKYCY1AF105Z VCKYCY1HB103K VCKYCY1CF104Z VCKYCY1HF103Z VCKYCY1HF102Z VCCCCY1HH5R0C VCEAPF1HW475M VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HF102Z RC-EZ1138CEZZ VCCCCY1HH7R0D VCEAPF1CW226M VCKYCY1HF103Z VCKYCY1HB103K VCEAPF0JW476M VCEAPF1HW475M VCKYCY1HB103K VCKYCY1EF104Z VCKYCY1HB103K VCKYCY1CF104Z VCKYCY1CF104Z VCCCCY1EH102J VCEAPF1CW226M VCEAPF1HW105M VCFRED1HM472J VCFRED1HM222J VCKYCY1EF104Z VCCCCY1EH102J VCCCCY1EH102J VCKYCY1EF104Z VCCCCY1EH102J VCCCCY1EH102J VCEAPF0JW476M VCKYCY1EF104Z VCCCCY1HH180J VCCCCY1HH180J VCKYCY1CF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1HF103Z VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCCCCY1HH470J VCCCCY1HH470J VCCCCY1HH221J VCCCCY1HH221J AB AB DIODES J J J J J Diode Zener Diode Zener Diode Diode Diode AA AB AB AB AB PACKAGED CIRCUITS J Crystal J Crystal AL AH COILS J J J J Peaking 33µH Peaking 27µH Peaking 33µH Peaking 22µH AC AC AC AC CAPACITORS J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 0.1 0.01 1.0 0.01 0.1 0.01 1000p 5.0p 4.7 0.01 0.01 1000p 10 7.0p 22 0.01 0.01 47 4.7 0.01 0.1 0.01 0.1 0.1 1000p 22 1.0 4700p 2200p 0.1 1000p 1000p 0.1 1000p 1000p 47 0.1 18p 18p 0.1 0.1 0.1 0.01 0.1 0.1 0.1 47p 47p 220p 220p 25V 50V 10V 50V 16V 50V 50V 50V 50V 50V 50V 50V 10V 50V 16V 50V 50V 6.3V 50V 50V 25V 50V 16V 16V 25V 16V 50V 50V 50V 25V 25V 25V 25V 25V 25V 6.3V 25V 50V 50V 16V 25V 25V 50V 25V 25V 25V 50V 50V 50V 50V Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Electrolytic Ceramic Electrolytic Ceramic Ceramic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Mylar Mylar Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic AA AA AC AA AA AA AA AA AB AA AA AA AF AA AB AA AA AB AB AA AA AA AA AA AB AB AB AD AC AA AB AB AA AB AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA 159 Ref. No. Part No. ★ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description C826 C827 C828 C829 C830 C831 C832 C833 C834 C835 C836 C837 C838 C839 C840 C844 C845 C852 C856 C857 C860 C861 C862 C863 C864 C865 C867 C868 C869 C870 C871 C872 C873 C877 C878 C879 C880 C881 C882 C883 C885 C886 VCKYCY1EF104Z VCE9PF1HW105M VCE9PF1HW105M VCEAPF1CW226M VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCFRED1HM332J VCEAPF1CW107M VCKYCY1EF104Z VCEAPF1CW107M VCKYCY1EF104Z VCEAPF1HW225M VCFYEC1CM223J VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCFYEC1CM274J VCKYCY1HB103K VCCCCY1HH221J VCE9PF1CW106M VCCCCY1HH390J VCKYCY1EF104Z VCE9PF1HW105M VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1HB103K VCKYCY1CF224Z VCCCCY1HH101J VCKYCY1HB103K VCEAPF1CW106M VCFYEC1CM274J VCEAPF1CW106M VCKYCY1CF104Z VCEAPF1CW106M VCE9PF1CW106M VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCCCCY1HH470J VCEAPF1CW226M C887 VCEAPF1CW106M J 10 C891 C892 C893 C903 C904 C905 C906 C907 C908 C909 C910 C911 C912 C913 C914 C915 C916 C917 C918 C919 C920 C921 C922 C923 C924 C925 C926 C927 C930 C931 VCKYCY1EF104Z VCKYCY1EF104Z VCEAPF1HW225M VCKYCY1CF104Z VCCCCY1HH120J VCCCCY1HH360J VCEAPF1HW105M VCKYCY1CF104Z VCKYCY1HB103K VCKYCY1HB103K VCCCCY1HH181J VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCEAPF1CW106M VCKYCY1CF104Z RC-EZ0569CEZZ VCKYCY1CF104Z VCCCCY1HH220J VCCCCY1HH5R0C VCCCCY1HH330J VCCCCY1HH470J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 0.1 1.0 1.0 22 0.1 0.1 0.1 0.1 3300p 100 0.1 100 0.1 2.2 0.022 0.1 0.1 0.1 0.27 0.01 220p 10 39p 0.1 1.0 0.1 0.1 0.01 0.22 100p 0.01 10 0.27 10 0.1 10 10 0.1 0.1 0.1 47p 22 0.1 0.1 2.2 0.1 12p 36p 1.0 0.1 0.01 0.01 180p 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 10 0.1 10 0.1 22p 5.0p 33p 47p 25V Ceramic 50V Elect.(N.P) 50V Elect.(N.P) 16V Electrolytic 25V Ceramic 25V Ceramic 25V Ceramic 25V Ceramic 50V Mylar 16V Electrolytic 25V Ceramic 16V Electrolytic 25V Ceramic 50V Electrolytic 16V Mylar 25V Ceramic 25V Ceramic 25V Ceramic 16V Mylar 50V Ceramic 50V Ceramic 16V Elect.(N.P) 50V Ceramic 25V Ceramic 50V Elect.(N.P) 25V Ceramic 25V Ceramic 50V Ceramic 16V Ceramic 50V Ceramic 50V Ceramic 16V Electrolytic 16V Mylar 16V Electrolytic 16V Ceramic 16V Electrolytic 16V Elect.(N.P) 16V Ceramic 16V Ceramic 16V Ceramic 50V Ceramic 16V Electrolytic (XG-C40XE) 16V Electrolytic (XG-C40XE) 25V Ceramic 25V Ceramic 50V Electrolytic 16V Ceramic 50V Ceramic 50V Ceramic 50V Electrolytic 16V Ceramic 50V Ceramic 50V Ceramic 50V Ceramic 16V Ceramic 16V Ceramic 16V Ceramic 16V Ceramic 16V Ceramic 16V Ceramic 16V Ceramic 16V Ceramic 16V Ceramic 16V Ceramic 16V Ceramic 16V Electrolytic 16V Ceramic 10V Electrolytic 16V Ceramic 50V Ceramic 50V Ceramic 50V Ceramic 50V Ceramic Code AA AC AC AB AA AA AA AA AD AD AA AD AA AB AC AA AA AA AE AA AA AC AA AA AC AA AA AA AA AA AA AB AE AB AA AB AC AA AA AA AA AB AB AA AA AB AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AF AA AA AA AA AA XG-C40XU/XE Ref. No. ★ Part No. Description Code DUNTKA211DE11/B116DE02 R624 R650 R699 R806 R807 R808 R811 R812 R815 R816 R817 R819 R820 R821 R832 R835 R837 R838 R839 R840 R841 R842 R843 R844 R845 R846 R848 R849 R850 R851 R852 R853 R855 R856 R857 R858 R859 R860 R861 R862 R863 R865 R866 R867 R869 R870 R871 R872 R873 R874 R875 R876 R877 R878 R879 R880 R891 R892 R893 R894 R895 R898 R901 R902 R903 R905 R906 R907 R908 R909 R910 R911 R912 R913 R914 SIGNAL UNIT (Continued) C932 C933 C934 C935 C936 C937 C938 C939 C945 C946 C948 C949 C950 C951 C954 C957 C958 C959 C960 C962 C963 C964 C965 C966 C967 C968 C970 C973 C1009 VCKYCY1AF105Z VCKYCY1CF104Z VCE9PF1CW106M VCCCCY1HH390J VCEAPF1CW106M VCKYCY1CF104Z VCKYCY1HB103K VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1HB103K VCKYCY1HB103K VCKYCY1HB103K VCEAPF0JW476M VCEAPF0JW476M VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCEAPF1CW226M VCFYEC1CM104J VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1HF103Z VCKYCY1HB103K VCCCCY1HH390J RC-EZ0569CEZZ R409 R410 R411 R412 R413 R414 R415 R416 R417 R418 R419 R438 R439 R440 R472 R477 R478 R479 R480 R481 R482 R496 R497 R503 R505 R584 R603 R604 R605 R608 R611 R613 R614 R615 R616 R617 R619 R621 R622 R623 VRS-TV1JD4R7J VRS-CY1JF273J VRS-CY1JF471J VRS-CY1JF822J VRS-CY1JF102J VRS-CY1JF100J VRS-CY1JF151J VRS-CY1JF562J VRS-CY1JF331J VRS-CY1JF103J VRS-CY1JF471J VRS-CY1JF474J VRS-CY1JF101J VRS-CY1JF331J VRS-CY1JF101J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF103J VRS-CY1JF361J VRS-CY1JF332F VRS-CY1JF392F VRS-CY1JF361J VRS-CY1JF101J VRS-CY1JF103J VRS-CY1JF562J VRS-CY1JF000J VRS-CY1JF152J VRN-CY1JF133D VRN-CY1JF752D VRS-CY1JF101J VRS-CY1JF182J VRN-CY1JF682D VRN-CY1JF103D VRS-CY1JF101J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 1.0 0.1 10 39p 10 0.1 0.01 0.1 0.1 0.1 0.1 0.1 0.01 0.01 0.01 47 47 0.1 0.1 0.1 22 0.1 0.1 0.1 0.1 0.01 0.01 39p 10 10V 16V 16V 50V 16V 16V 50V 16V 16V 16V 16V 16V 50V 50V 50V 6.3V 6.3V 16V 16V 16V 16V 16V 16V 16V 16V 50V 50V 50V 10V Ceramic Ceramic Elect.(N.P) Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Ceramic Ceramic Ceramic Electrolytic Mylar Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic AC AA AC AA AB AA AA AA AA AA AA AA AA AA AA AB AB AA AA AA AB AD AA AA AA AA AA AA AF 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Film 1/16W Metal Film 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Film 1/16W Metal Film 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AB AA AA AA AA AA RESISTORS J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 4.7 27k 470 8.2k 1.0k 10 150 5.6k 330 10k 470 470k 100 330 100 1.0k 1.0k 1.0k 0 0 10k 360 3.3k 3.9k 360 100 10k 5.6k 0 1.5k 13k 7.5k 100 1.8k 6.8k 10k 100 0 0 0 Ref. No. 160 Part No. ★ VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF101J VRS-CY1JF561J VRS-CY1JF681J VRS-CY1JF183J VRS-TX2HF5R6J VRS-CY1JF104J VRS-TX2HF4R7J VRS-CY1JF392J VRS-CY1JF103J VRS-CY1JF473J VRS-TX2HF4R7J VRS-CY1JF393J VRS-CY1JF564J VRS-CY1JF333J VRS-CY1JF104J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF472J VRS-CY1JF103J VRS-CY1JF822J VRS-CY1JF102J VRS-CY1JF103J VRS-CY1JF221J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF222J VRS-CY1JF103J VRS-CY1JF822J VRS-CY1JF000J VRS-CY1JF472J VRS-CY1JF473J VRS-CY1JF682J VRS-CY1JF103J VRS-CY1JF183J VRS-CY1JF223J VRS-CY1JF682J VRS-CY1JF103J VRS-CY1JF472J VRS-CY1JF102J VRS-CY1JF683J VRS-CY1JF224J VRS-CY1JF101J VRS-CY1JF472J VRS-CY1JF682J VRS-CY1JF332J VRS-CY1JF102J VRS-CY1JF682J VRS-CY1JF273J VRS-CY1JF392J VRS-CY1JF103J VRS-CY1JF102J VRS-CY1JF333J VRS-CY1JF223J VRS-CY1JF223J VRS-CY1JF821J VRS-CY1JF000J VRS-TV1JD122J VRS-CY1JF223J VRS-CY1JF103J VRN-CY1JF102D VRS-TV1JD122J VRS-TV1JD471J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF821J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 0 0 0 0 100 560 680 18k 5.6 100k 4.7 3.9k 10k 47k 4.7 39k 560k 33k 100k 100 100 100 100 100 1.0k 1.0k 1.0k 4.7k 10k 8.2k 1.0k 10k 220 100 100 2.2k 10k 8.2k 0 4.7k 47k 6.8k 10k 18k 22k 6.8k 10k 4.7k 1.0k 68k 220k 100 4.7k 6.8k 3.3k 1.0k 6.8k 27k 3.9k 10k 1.0k 33k 22k 22k 820 0 1.2k 22k 10k 1.0k 1.2k 470 10k 10k 820 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/2W Metal Oxide 1/16W Metal Oxide 1/2W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/2W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Film 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide Code AA AA AA AA AA AA AA AA AA AA AB AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA XG-C40XU/XE Ref. No. Part No. ★ Description Code DUNTKA211DE11/B116DE02 SIGNAL UNIT (Continued) R915 R916 R917 R918 R919 R920 R922 R923 R924 R925 R926 R927 R928 R929 R930 R931 R932 R933 R934 R935 R936 R937 R938 R939 R940 R941 R942 R943 R944 R945 R952 R953 R954 R955 R956 R957 R958 R959 R964 R975 R976 R980 R981 R982 R983 R990 R991 R999 R1005 R1006 R1007 R1008 R1009 R1010 VRN-CY1JF332D VRN-CY1JF332D VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF103J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-TV1JD222J VRS-CY1JF823J VRS-CY1JF473J VRS-CY1JF471J VRS-CY1JF561J VRS-CY1JF223J VRS-CY1JF223J VRS-CY1JF152J VRS-CY1JF681J VRS-CY1JF102J VRS-CY1JF273J VRS-TX2HF5R6J VRS-CY1JF273J VRS-CY1JF471J VRS-CY1JF822J VRS-CY1JF103J VRS-CY1JF331J VRS-CY1JF750J VRS-CY1JF471J VRS-CY1JF562J VRS-CY1JF102J VRS-TX2HF6R8J VRS-CY1JF101J VRS-CY1JF102J VRS-CY1JF471J VRS-CY1JF681J VRS-CY1JF154J VRS-CY1JF102J VRS-TV1JD222J VRS-CY1JF000J VRS-TX2HF5R6J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF104J VRS-CY1JF104J VRS-CY1JF000J VRS-TX2HF5R6J VRS-TX2HF5R6J VRN-CY1JF562D VRN-CY1JF102D VRS-CY1JF103J VRS-CY1JF000J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J R1011 VRS-CY1JF000J J 0 R1013 VRS-CY1JF000J J 0 R1801 R1802 R1803 R1804 R1805 R1806 R1807 R1808 R1809 R1810 R1811 R1812 J J J J J J J J J J J J VRS-CY1JF223J VRS-CY1JF333J VRS-CY1JF103J VRS-CY1JF102J VRS-CY1JF102F VRS-CY1JF102F VRS-CY1JF122J VRS-CY1JF821J VRS-CY1JF102J VRS-CY1JF122J VRS-CY1JF122J VRS-CY1JF104J 3.3k 3.3k 1.0k 1.0k 10k 100 100 100 100 2.2k 82k 47k 470 560 22k 22k 1.5k 680 1.0k 27k 5.6 27k 470 8.2k 10k 330 75 470 5.6k 1.0k 6.8 100 1.0k 470 680 150k 1.0k 2.2k 0 5.6 10k 10k 10k 10k 10k 100k 100k 0 5.6 5.6 5.6k 1.0k 10k 0 22k 33k 10k 1.0k 1.0k 1.0k 1.2k 820 1.0k 1.2k 1.2k 100k 1/16W Metal Film 1/16W Metal Film 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/2W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/2W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/2W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/2W Metal Oxide 1/2W Metal Oxide 1/16W Metal Film 1/16W Metal Film 1/16W Metal Oxide 1/16W Metal Oxide (XG-C40XE) 1/16W Metal Oxide (XG-C40XE) 1/16W Metal Oxide (XG-C40XE) 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AA AA ★ Description R1813 VRS-CY1JF101J R1814 VRS-CY1JF000J J 100 J 0 R1819 R1820 R1822 R1823 R1825 R1826 VRS-CY1JF102J VRS-CY1JF152J VRS-CY1JF332J VRS-CY1JF222J VRS-CY1JF391J VRS-CY1JF000J J J J J J J 1/16W Metal Oxide 1/16W Metal Oxide (XG-C40XE) 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide FB402 FB902 FB903 FB904 P401 P402 P801 P1501 P1502 RBLN-0065CEZZ RBLN-0065CEZZ RBLN-0065CEZZ RBLN-0065CEZZ QPLGZ3044CEZZ QPLGZ3044CEZZ QPLGN0463TAZZ QPLGZ2026CEZZ QPLGZ2026CEZZ Ref. No. Part No. 1.0k 1.5k 3.3k 2.2k 390 0 Code AA AA AA AA AA AA AA AA MISCELLANEOUS PARTS J J J J J J J J J Frrite Bead Frrite Bead Frrite Bead Frrite Bead Plug 30-Pin (TN) Plug 30-Pin (VS) Plug 4-Pin Plug 20-Pin Plug 20-Pin AB AB AB AB AH AH AC AE AE DUNTKA212DE11/B117DE02 PC TERMINAL UNIT INTEGRATED CIRCUITS IC3003 IC3004 IC3005 IC3006 IC3009 IC3010 IC3011 IC3012 IC3013 IC3014 IC3015 IC3303 IC3304 IC7006 VHiTL712CPW-1 VHiTL712CPW-1 VHiTL712CPW-1 RH-iX2317CEZZ VHiTL712CPW-1 VHiTL712CPW-1 VHiAD8185++-1 VHiVHC157MT-1 VHi24LC21//-1 VHi24LC21//-1 VHiTL712CPW-1 VHiNJM2245M-1 VHiNJM2245M-1 VHiUPD4721G-1 J J J J J J J J J J J J J J Tl712CPWR Tl712CPWR Tl712CPWR SN74AlS1034NS Tl712CPWR Tl712CPWR AD8185ARU 74VHC157MTCX 24LC21T 24LC21T Tl712CPWR NJM2245M NJM2245M UPD4721G-GJG AL AL AL AF AL AL AW AE AN AN AL AF AF AQ TRANSISTORS Q3301 VS2SC3928AR-1 Q3302 VSDTC143ZE/-1 J 2SC3928AR J DTC143ZE AB AB DIODES D3003 D3004 D3020 D3021 D3022 D3023 D3024 D3028 D3029 D3032 D3033 D3034 D3305 D3306 D3307 D3311 D3312 D3313 D3314 D3315 D3316 D7025 D7026 D7027 D7028 AA AA AA AA AA AA AA AA AA AA AA AA AA AA 161 VHDMA152WA/-1 VHDMA152WA/-1 VHDMA152WA/-1 VHDMA152WA/-1 VHDMA152WA/-1 VHDMA152WA/-1 VHDMA152WA/-1 VHDMA152WA/-1 VHDMA152WA/-1 VHDMA152WA/-1 VHDMA152WA/-1 VHDMA152WA/-1 VHDMA3120WA-1 VHDMA3120WA-1 VHDMA3120WA-1 VHDMA157A//-1 VHDMA157A//-1 VHDMA157A//-1 VHDMA157A//-1 VHDMA157A//-1 VHDMA157A//-1 VHDMA3120WA-1 VHDMA3120WA-1 VHDMA3120WA-1 VHDMA3120WA-1 J J J J J J J J J J J J J J J J J J J J J J J J J Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode AA AA AA AA AA AA AA AA AA AA AA AA AK AK AK AC AC AC AC AC AC AK AK AK AK XG-C40XU/XE Ref. No. ★ Part No. Description Code DUNTKA212DE11/B117DE02 PC TERMINAL UNIT (Continued) Ref. No. ★ Part No. C7020 C7021 C7501 C7502 VCEAPF1HW225M VCEAPF1HW225M VCEAPF0JW107M VCKYCY1CF104Z R2001 R2002 R2003 R3004 R3005 R3006 R3007 R3008 R3009 R3010 R3011 R3012 R3013 R3014 R3015 R3016 R3017 R3018 R3023 R3024 R3025 R3026 R3027 R3028 R3029 R3030 R3031 R3032 R3033 R3036 R3046 R3054 R3055 R3056 R3057 R3058 R3059 R3060 R3061 R3062 R3063 R3092 R3093 R3094 R3096 R3100 R3102 R3103 R3112 R3116 R3117 R3118 R3119 R3120 R3121 R3130 R3131 R3132 R3138 R3139 R3140 R3141 R3142 R3143 R3144 R3145 R3146 R3147 R3149 VRS-TW2ED750J VRS-TW2ED750J VRS-TW2ED750J VRS-CY1JF102J VRS-CY1JF392J VRS-CY1JF102J VRS-CY1JF271J VRS-CY1JF222J VRS-CY1JF102J VRS-CY1JF392J VRS-CY1JF102J VRS-CY1JF271J VRS-CY1JF222J VRS-CY1JF102J VRS-CY1JF392J VRS-CY1JF102J VRS-CY1JF271J VRS-CY1JF222J VRS-CY1JF101J VRS-CY1JF103J VRS-TW2ED750J VRS-TW2ED750J VRS-TW2ED750J VRS-CY1JF224J VRS-CY1JF224J VRS-CY1JF224J VRS-CY1JF224J VRS-CY1JF224J VRS-CY1JF224J VRS-CY1JF000J VRS-CY1JF102J VRS-CY1JF271J VRS-CY1JF222J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF392J VRS-CY1JF271J VRS-CY1JF102J VRS-CY1JF222J VRS-CY1JF102J VRS-CY1JF392J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF102J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF473J VRS-CY1JF103J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-TW2ED750J VRS-TW2ED750J VRS-TW2ED750J VRS-CY1JF473J VRS-CY1JF103J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF102J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF102J J J J J Description 2.2 2.2 100 0.1 50V 50V 6.3V 16V Code Electrolytic Electrolytic Electrolytic Ceramic AB AB AC AA 1/4W Metal Oxide 1/4W Metal Oxide 1/4W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/4W Metal Oxide 1/4W Metal Oxide 1/4W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/4W Metal Oxide 1/4W Metal Oxide 1/4W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA FILTERS AND COIL FL3001 FL3002 FL3003 FL3006 FL3007 FL3008 FL3011 FL3012 FL3013 L3006 RFiLN0003TAZZ RFiLN0003TAZZ RFiLN0003TAZZ RFiLN0003TAZZ RFiLN0003TAZZ RFiLN0003TAZZ RFiLN0003TAZZ RFiLN0003TAZZ RFiLN0003TAZZ VP-1M100J1R6N C3001 C3002 C3003 C3004 C3005 C3006 C3008 C3009 C3010 C3027 C3028 C3029 C3030 C3031 C3032 C3033 C3034 C3039 C3040 C3041 C3042 C3043 C3044 C3045 C3046 C3047 C3062 C3063 C3065 C3066 C3067 C3070 C3071 C3073 C3075 C3076 C3077 C3078 C3080 C3081 C3304 C3305 C3306 C3309 C3310 C3311 C3312 C3313 C3314 C3319 C3320 C3321 C3322 C3323 C7001 C7017 C7018 C7019 VCCCCY1HH330J VCKYCY1CF104Z VCKYCY1CF104Z VCCCCY1HH330J VCKYCY1CF104Z VCKYCY1CF104Z VCCCCY1HH330J VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCEAPF0JW476M VCEAPF0JW476M VCKYCY1HB103K VCKYCY1HB103K VCEAPF0JW476M VCKYCY1HB103K VCEAPF0JW476M VCEAPF0JW476M VCKYCY1HB103K VCKYCY1HB103K VCEAPF0JW476M VCKYCY1HB103K VCCCCY1HH330J VCKYCY1CF104Z VCCCCY1HH330J VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCEAPF0JW476M VCKYCY1CF104Z VCKYCY1CF104Z VCEAPF0JW476M VCKYCY1HB103K VCKYCY1HB103K VCCCCY1HH330J VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCEAPF0JW226M VCKYCY1CF104Z VCCCCY1HH101J RC-KZ0416CEZZ RC-KZ0416CEZZ VCCCCY1HH101J VCCCCY1HH101J VCCCCY1HH101J VCCCCY1HH101J VCEAPF1CW106M VCEAPF1CW106M VCEAPF1CW106M VCEAPF1CW106M VCEAPF1CW106M VCEAPF1CW106M VCEAPF1CW106M VCEAPF0JW476M VCEAPF1HW225M VCEAPF1HW225M VCKYCY1CF104Z J J J J J J J J J J Filter Filter Filter Filter Filter Filter Filter Filter Filter Peaking 10µH RESISTORS AD AD AD AD AD AD AD AD AD AC CAPACITORS J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 33p 0.1 0.1 33p 0.1 0.1 33p 0.1 0.1 0.1 47 47 0.01 0.01 47 0.01 47 47 0.01 0.01 47 0.01 33p 0.1 33p 0.1 0.1 0.1 47 0.1 0.1 47 0.01 0.01 33p 0.1 0.1 0.1 22 0.1 100p 10 10 100p 100p 100p 100p 10 10 10 10 10 10 10 47 2.2 2.2 0.1 50V 16V 16V 50V 16V 16V 50V 16V 16V 16V 6.3V 6.3V 50V 50V 6.3V 50V 6.3V 6.3V 50V 50V 6.3V 50V 50V 16V 50V 16V 16V 16V 6.3V 16V 16V 6.3V 50V 50V 50V 16V 16V 16V 6.3V 16V 50V 25V 25V 50V 50V 50V 50V 16V 16V 16V 16V 16V 16V 16V 6.3V 50V 50V 16V Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Ceramic Ceramic Electrolytic Ceramic Electrolytic Electrolytic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Ceramic AA AA AA AA AA AA AA AA AA AA AB AB AA AA AB AA AB AB AA AA AB AA AA AA AA AA AA AA AB AA AA AB AA AA AA AA AA AA AB AA AA AE AE AA AA AA AA AB AB AB AB AB AB AB AB AB AB AA 162 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 75 75 75 1.0k 3.9k 1.0k 270 2.2k 1.0k 3.9k 1.0k 270 2.2k 1.0k 3.9k 1.0k 270 2.2k 100 10k 75 75 75 220k 220k 220k 220k 220k 220k 0 1.0k 270 2.2k 1.0k 1.0k 3.9k 270 1.0k 2.2k 1.0k 3.9k 1.0k 1.0k 100 100 100 100 100 1.0k 100 100 100 47k 10k 100 100 100 100 75 75 75 47k 10k 100 100 1.0k 100 100 1.0k XG-C40XU/XE Ref. No. Part No. ★ Description Code PC TERMINAL UNIT (Continued) VRS-CY1JF271J VRS-CY1JF222J VRS-CY1JF392J VRS-CY1JF102J VRS-CY1JF101J VRS-CY1JF680J VRS-CY1JF473J VRS-CY1JF680J VRS-CY1JF473J VRS-CY1JF680J VRS-CY1JF473J VRS-CY1JF680J VRS-CY1JF473J VRS-CY1JF680J VRS-CY1JF473J VRS-CY1JF680J VRS-CY1JF473J VRS-CY1JF123J VRS-CY1JF123J VRS-CY1JF224J VRS-CY1JF224J VRS-CY1JF681J VRS-CY1JF681J VRS-CY1JF105J VRS-CY1JF105J VRS-TV1JD000J J J J J J J J J J J J J J J J J J J J J J J J J J J 270 2.2k 3.9k 1.0k 100 68 47k 68 47k 68 47k 68 47k 68 47k 68 47k 12k 12k 220k 220k 680 680 1.0M 1.0M 0 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W R3314 VRS-TV1JD000J J 0 1/16W R3319 R3320 R3321 R3322 R3323 R3324 R3325 R3326 R3327 R3328 R3329 R3330 R3331 R7045 R7048 R7090 R7091 R7501 R7562 R7563 R7564 R7565 R7566 R7567 VRS-CY1JF101J VRS-CY1JF102J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF102J VRS-CY1JF101J VRS-CY1JF272J VRS-TV1JD122J VRS-CY1JF272J VRS-CY1JF153J VRS-TW2ED750J VRS-TW2ED750J VRS-TW2ED750J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF471J VRS-TX2HF220J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J J J J J J J J J J J J J J J J J J J J J J J J J 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/4W 1/4W 1/4W 1/16W 1/16W 1/16W 1/16W 1/16W 1/2W 1/16W 1/16W 1/16W 1/16W 1/16W FB3004 FB3005 FB3009 FB3010 FB3014 FB3015 FB3016 FB3301 FB3302 FB3303 FB3307 FB3308 FB3309 FB7001 FB7002 FB7003 RBLN-0060TAZZ RBLN-0060TAZZ RBLN-0060TAZZ RBLN-0060TAZZ RBLN-0060TAZZ RBLN-0060TAZZ RBLN-0060TAZZ RBLN-0062TAZZ RBLN-0062TAZZ RBLN-0062TAZZ RBLN-0062TAZZ RBLN-0062TAZZ RBLN-0062TAZZ RBLN-0058TAZZ RBLN-0058TAZZ RBLN-0058TAZZ 100 1.0k 100 100 1.0k 100 2.7k 1.2k 2.7k 15k 75 75 75 0 0 100 100 470 22 100 100 0 0 0 Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide (XG-C40XE) Metal Oxide (XG-C40XE) Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead(XG-C40XU) Frrite Bead Frrite Bead Frrite Bead(XG-C40XU) Frrite Bead Frrite Bead Frrite Bead J J J J J J J J J J J J Description Frrite Bead Jack JDIO-IN Jack TOR-OUT Socket 30-Pin (TN) Socket 15-Pin D-sub Socket 15-Pin D-sub Socket 15-Pin D-sub Socket 9-Pin D-sub R/C Receiver Sheild Sheild Shafr Code AC AD AD AG AM AM AM AH AF AK AD AD DUNTKA693DE01/02 SOUND OUT/REGULATOR UNIT INTEGRATED CIRCUITS IC1030 RH-iX2204CEZZ IC1031 VHiPQ05TZ11-1 IC7301 VHiTDA1517/-1 J PQ12TZ11 J PQ05TZ11 J TDA1517/N2 AG AH AL TRANSISTORS AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA Q1001 Q1002 Q7301 Q7302 Q7303 Q7304 Q7305 VSDTC144EK/-1 VSDTC144EK/-1 VS2SC3928AR-1 VS2SD1664R/-1 VS2SD1664R/-1 VSDTA114EU/-1 VSDTC114EU/-1 J J J J J J J D1020 D1021 D1023 D1024 VHDDAN202K/-1 VHDDAN202K/-1 RH-EX0516CEZZ RH-EX0516CEZZ C1020 C1021 C1022 C1023 C1024 C1025 C1026 C1027 C1046 C1047 C1048 C1049 C1050 C1051 C1052 C1053 C7301 C7302 C7304 C7305 C7306 C7307 C7308 C7309 C7310 C7312 C7315 VCEAPF1EW336M VCKYCY1EF104Z VCEAPF1CW336M VCKYCY1CF104Z VCEAPF1CW336M VCKYCY1CF104Z VCEAPF1CW336M VCKYCY1CF104Z VCEAPF1CW107M VCKYCY1CF104Z VCKYCY1CF104Z VCEAPF1CW107M VCKYCY1CF104Z VCEAPF1CW107M VCKYCY1AF105Z VCKYCY1AF105Z VCEAPF1HW475M VCKYTV1CF105Z VCE9PF1CW475M VCCCCY1HH471J VCEA2A1EW477M VCKYCY1EF104Z VCEAPF1CW107M VCEA2A1CW108M VCEAPF1CW107M VCEAPF1CW107M VCKYCY1AF105Z R1020 R1021 R1022 R1023 VRS-TX2HF5R6J VRS-TX2HF5R6J VRS-TV1JD103J VRS-TV1JD103J DTC144EK DTC144EK 2SC3928AR 2SD1664R 2SD1664R DTC114EU DTC114EU AB AB AB AC AC AB AB DIODES J J J J Diode Diode Zener Diode Zener Diode AB AB AB AB CAPACITORS MISCELLANEOUS PARTS J J J J J J J J J J J J J J J J ★ Part No. FB7004 RBLN-0058TAZZ J3301 QJAKJ0008GEZZ J3303 QJAKJ0008GEZZ SC3001 QSOCZ3043CEZZ SC3002 QSOCN0448FJZZ SC3003 QSOCN0448FJZZ SC3004 QSOCN0344FJZZ SC7004 QSOCD0901CEZZ RMC7501 RRMCU0233CEZZ PSLDM3024CEFW QEARP0085CEFW NSFTZ0134CEFW DUNTKA212DE11/B117DE02 R3150 R3151 R3152 R3153 R3154 R3155 R3156 R3157 R3158 R3159 R3160 R3161 R3162 R3163 R3164 R3165 R3166 R3301 R3302 R3303 R3304 R3309 R3310 R3311 R3312 R3313 Ref. No. AB AB AB AB AB AB AB AB AB AB AB AB AB AC AC AC J J J J J J J J J J J J J J J J J J J J J J J J J J J 33 0.1 33 0.1 33 0.1 33 0.1 100 0.1 0.1 100 0.1 100 1.0 1.0 4.7 1.0 4.7 470p 470 0.1 100 1000 100 100 1.0 25V 25V 16V 16V 16V 16V 16V 16V 16V 16V 16V 16V 16V 16V 10V 10V 50V 16V 16V 50V 25V 25V 16V 16V 16V 16V 10V Electrolytic Ceramic Electrolytic Ceramic Electrolytic Ceramic Electrolytic Ceramic Electrolytic Ceramic Ceramic Electrolytic Ceramic Electrolytic Ceramic Ceramic Electrolytic Ceramic Elect.(N.P) Ceramic Electrolytic Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Ceramic AB AA AB AA AB AA AB AA AD AA AA AD AA AD AC AC AB AB AC AA AD AA AD AB AD AD AC 1/2W 1/2W 1/16W 1/16W Metal Oxide Metal Oxide Metal Oxide Metal Oxide AA AA AA AA RESISTORS 163 J J J J 5.6 5.6 10k 10k XG-C40XU/XE Ref. No. Part No. ★ Description Code DUNTKA693DE01/02 SOUND OUT/REGULATOR UNIT (Continued) R1027 R1028 R1039 R1042 R1044 R1045 R1050 R7301 R7302 R7303 R7304 R7307 R7310 R7311 R7312 R7313 R7314 R7315 R7316 R7317 VRS-TX2HF2R2J VRS-TX2HF2R2J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF474F VRS-CY1JF103J VRS-TX2HF000J VRS-CY1JF103J VRS-CY1JF682J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF392J VRS-TV1JD103J VRS-CY1JF101J VRS-TX2HF000J VRS-TX2HF000J VRS-TV1JD000J VRS-TX2HF2R2J VRS-TX2HF2R2J VRS-CY1JF101J J J J J J J J J J J J J J J J J J J J J UNT1001 FB1005 P1010 P1011 P7302 P7303 RCNVD0015CEZZ J RBLN-0060CEZZ J QPLGN0428FJZZ J QPLGN0430FJZZ J QPLGN0464TAZZ J QPLGN0174FJZZ J PRDAR1551CEFW J QCNW-5705CEZZ J LHLDW1072GEZZ J LX-BZ3266CEFD J 2.2 2.2 0 0 470k 10k 0 10k 6.8k 10k 10k 3.9k 10k 100 0 0 0 2.2 2.2 100 1/2W 1/2W 1/16W 1/16W 1/16W 1/16W 1/2W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/2W 1/2W 1/16W 1/2W 1/2W 1/16W Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AA Ref. No. Part No. ★ IC1502 IC1504 IC1505 IC1506 IC1507 IC1508 IC1701 IC5003 IC5004 IC5005 IC5006 IC5007 IC5008 IC5009 IC5010 IC5021 IC5101 IC5102 IC5503 IC5504 IC5505 IC5506 IC5507 IC5508 VHiNJM2902V-1 VHiLV123AT+-1 VHiAHC2G241-1 VHiAHC2G241-1 VHiPQ05TZ11-1 VHiAHC2G241-1 VHiNJM2904V-1 VHiM62352GP-1 VHiM62320FP-1 VHiM62320FP-1 VHiSNHC00T/-1 VHiM62320FP-1 VHiM24C64WN-1 VHiSNHC08T/-1 VHiPST600iM-1 VHiBA033SFP-1 RH-iX3393CEZZ VHiAHC2G241-1 VHiPQ05SZ51-1 VHiBA00ASFP-1 VHiBA00ASFP-1 VHiSN1G66DC-1 VHiBA00ASFP-1 VHiBA00ASFP-1 J J J J J J J J J J J J J J J J J J J J J J J J Q1101 Q1105 Q1106 Q1107 Q1108 Q1110 Q1112 Q1113 Q1114 Q1205 Q1206 Q1207 Q1208 Q1210 Q1211 Q1212 Q1213 Q1301 Q1305 Q1306 Q1307 Q1308 Q1310 Q1311 Q1312 Q1313 Q1401 Q1402 Q1403 Q1410 Q1411 Q1412 Q1413 Q1501 Q1502 Q1503 Q1505 Q1506 Q1507 Q1601 Q1602 Q1603 Q1604 Q1605 Q1606 Q1607 Q1608 Q1609 Q1610 VS2SA1530AR-1 VS2SC2411KR-1 VS2SA1036KR-1 VS2SC2411KR-1 VS2SA1036KR-1 VS2SC2411KR-1 VS2SA1036KR-1 VS2SC2411KR-1 VS2SA1036KR-1 VS2SC2411KR-1 VS2SA1036KR-1 VS2SC2411KR-1 VS2SA1036KR-1 VS2SC2411KR-1 VS2SC2411KR-1 VS2SA1036KR-1 VS2SA1036KR-1 VS2SA1530AR-1 VS2SC2411KR-1 VS2SA1036KR-1 VS2SC2411KR-1 VS2SA1036KR-1 VS2SC2411KR-1 VS2SC2411KR-1 VS2SA1036KR-1 VS2SA1036KR-1 VS2SC2735//-1 VS2SC2735//-1 VS2SC2735//-1 VS2SC2735//-1 VS2SC2735//-1 VS2SC2735//-1 VS2SC2735//-1 VSHN1B04FU/-1 VSHN1B04FU/-1 VSHN1B04FU/-1 VSHN1B04FU/-1 VSHN1B04FU/-1 VSHN1B04FU/-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VSDTC144EU/-1 VSDTC144EU/-1 VSDTC144EU/-1 VSDTC144EU/-1 VSDTC144EU/-1 VSDTC144EU/-1 MISCELLANEOUS PARTS DC/DC Converter Frrite Bead Plug 18-Pin (EA) Plug 20-Pin (EB) Plug 4-Pin (SO) Plug 2-Pin (SP) Heat Sink Connecting Cord Holder Screw OUTPUT UNIT INTEGRATED CIRCUITS RH-iX2204CEZZ VHiET6050S0-1 VHiET6050S0-1 VHiET1030F0-1 VHiET6050S0-1 VHiET6050S0-1 VHiNJM2902V-1 VHiET1030F0-1 VHiET6050S0-1 VHiET6050S0-1 VHiET1030F0-1 VHiLM2663M+-1 VHiCXA2111R-1 VHi74LV221+-1 VHiNJM2060V-1 VHiM62352GP-1 VHiT7SET08U-1 VHiHCT541AF-1 VHiPQ20VZ11-1 VHiPQ05TZ11-1 VHiTA8184F/-1 VHiM62352GP-1 VHiLV4053AT-1 J J J J J J J J J J J J J J J J J J J J J J J PQ12TZ11 ET6050S0B ET6050S0B ET1030F0A ET6050S0B ET6050S0B NJM2902V ET1030F0A ET6050S0B ET6050S0B ET1030F0A LM2663MX CXA2111R SN74LV221ANSR NJM2060V M62352GP TC7SET08FU TC74HCT541AF PQ20VZ11 PQ05TZ11 TA8184F M62352GP SN74LV4053APWR NJM2902V SN74LV123APWR SN74AHC2G241HD SN74AHC2G241HD PQ05TZ11 SN74AHC2G241HD NJM2904V M62352GP M62320FP M62320FP SN74HC00PW M62320FP M24C64-WMN6T SN74HC08PW IC-PST600IMT BA033SFP-E2 MB89P538-101PF SN74AHC2G241HD PQ05SZ51 BA00ASFP-E2 BA00ASFP-E2 SN74AHC1G66HDC BA00ASFP-E2 BA00ASFP-E2 Code AD AF AF AF AH AF AF AQ AK AK AG AK AL AG AE AG AR AF AG AG AG AD AG AG TRANSISTORS BC AC AD AD AC AC AG AF AA AA DUNTKA694DE01/02 IC1004 IC1101 IC1102 IC1106 IC1201 IC1202 IC1204 IC1206 IC1301 IC1302 IC1306 IC1307 IC1401 IC1402 IC1403 IC1404 IC1406 IC1408 IC1409 IC1410 IC1411 IC1412 IC1501 Description AG BA BA AW BA BA AD AW BA BA AW AS BB AG AF AQ AE AG AH AH AN AQ AE 164 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 2SA1530AR 2SC2411KR 2SA1036KR 2SC2411KR 2SA1036KR 2SC2411KR 2SA1036KR 2SC2411KR 2SA1036KR 2SC2411KR 2SA1036KR 2SC2411KR 2SA1036KR 2SC2411KR 2SC2411KR 2SA1036KR 2SA1036KR 2SA1530AR 2SC2411KR 2SA1036KR 2SC2411KR 2SA1036KR 2SC2411KR 2SC2411KR 2SA1036KR 2SA1036KR 2SC2735 2SC2735 2SC2735 2SC2735 2SC2735 2SC2735 2SC2735 HN1B04FU HN1B04FU HN1B04FU HN1B04FU HN1B04FU HN1B04FU 2SC3928AR 2SC3928AR 2SC3928AR 2SC3928AR DTC144EU DTC144EU DTC144EU DTC144EU DTC144EU DTC144EU AB AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AB AC AC AC AC AC AC AC AC AB AB AB AB AB AB AB AC AC AC AC AC AC AB AB AB AB AB AB AB AB AB AB XG-C40XU/XE Ref. No. ★ Part No. Description Code J J J J J J J J J J J J J J J J J J J J J J J J D1003 D1401 D1402 D1502 D5001 D5002 D5003 D5004 D5005 D5006 D5007 D5008 D5009 D5010 D5011 D5012 D5013 D5014 D5015 D5016 D5017 D5018 D5023 D5024 D5503 D5504 D5505 D5513 D5514 D5520 D5521 D5522 D5523 VHDDAN202K/-1 VHDDAN202K/-1 VHDDAN202K/-1 VHDDAN202K/-1 VHDHRW0702A-1 VHDHRW0702A-1 VHDHRW0702A-1 VHDHRW0702A-1 VHDMA153///-1 VHDMA153///-1 VHDMA153///-1 VHDMA153///-1 VHDHRW0702A-1 VHDHRW0702A-1 VHDHRW0702A-1 VHDHRW0702A-1 VHDMA153///-1 VHDMA153///-1 VHDMA153///-1 VHDMA153///-1 VHDHRW0702A-1 VHDMA153///-1 VHDDAN202K/-1 RH-EX0858CEZZ VHDDAN202K/-1 VHDDAN202K/-1 VHDDAN202K/-1 VHDDAN202K/-1 RH-EX0516CEZZ VHDDAN202K/-1 VHDDAN202K/-1 VHDDAN202K/-1 VHDDAN202K/-1 X5101 RCRSB0286CEZZ L1101 L1201 L1301 L1302 VP-1M100J1R6N VP-1M100J1R6N VP-1M100J1R6N VP-NM100KR42N DTC144EU DTC144EU DTC144EU DTC144EU DTC144EU DTC144EU DTC144EU DTC144EU DTC114EU DTC114EU 2SC3928AR 2SC3928AR 2SC3928AR 2SC3928AR 2SC3928AR DTC144EU 2SC3928AR 2SC3928AR 2SC3928AR 2SC3928AR DTC114EU 2SA1036KR DTC114EU 2SC3928AR C1010 C1013 C1101 C1102 C1103 C1104 C1105 C1106 C1107 C1108 C1109 C1110 C1112 C1113 C1114 C1115 C1116 C1117 C1118 C1126 C1127 C1128 C1130 C1141 C1142 C1143 C1144 C1145 C1146 C1147 C1148 C1201 C1202 C1203 C1204 C1206 C1207 C1208 C1209 C1210 C1212 C1213 C1214 C1215 C1216 C1217 C1218 C1219 C1225 C1226 C1227 C1228 C1229 C1241 C1242 C1243 C1244 C1245 C1247 C1301 C1302 C1303 C1304 C1305 C1306 C1307 C1308 C1309 C1310 C1312 C1313 C1314 AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AC AB AB DIODES J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Zener Diode Diode Diode Diode Diode Zener Diode Diode Diode Diode Diode AB AB AB AB AE AE AE AE AB AB AB AB AE AE AE AE AB AB AB AB AE AB AB AC AB AB AB AB AB AB AB AB AB PACKAGED CIRCUIT J Crystal AH COILS J J J J Peaking 10µH Peaking 10µH Peaking 10µH Peaking 10µH AC AC AC AB CONTROLS R1649 RVR-M4846GEZZ J 220k (B) Description J 220k (B) Code AC CAPACITORS OUTPUT UNIT (Continued) VSDTC144EU/-1 VSDTC144EU/-1 VSDTC144EU/-1 VSDTC144EU/-1 VSDTC144EU/-1 VSDTC144EU/-1 VSDTC144EU/-1 VSDTC144EU/-1 VSDTC114EU/-1 VSDTC114EU/-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VSDTC144EU/-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VSDTC114EU/-1 VS2SA1036KR-1 VSDTC114EU/-1 VS2SC3928AR-1 ★ Part No. R1652 RVR-M4846GEZZ DUNTKA694DE01/02 Q1611 Q1612 Q1613 Q1614 Q1615 Q1616 Q1617 Q1618 Q1619 Q1620 Q5002 Q5003 Q5004 Q5005 Q5007 Q5008 Q5514 Q5516 Q5517 Q5518 Q5519 Q5520 Q5526 Q5536 Ref. No. AC 165 VCEAPF1EW336M J 33 RC-EZ1146CEZZ J 27 RC-KZ0416CEZZ J 10 VCKYCY1EF104Z J 0.1 RC-KZ0416CEZZ J 10 VCKYCY1CF104Z J 0.1 VCKYCY1CF104Z J 0.1 RC-KZ0416CEZZ J 10 VCKYCY1EF104Z J 0.1 RC-KZ0416CEZZ J 10 VCKYCY1CF104Z J 0.1 VCKYCY1CF104Z J 0.1 RC-KZ0416CEZZ J 10 VCKYCY1EF104Z J 0.1 VCKYCY1EF104Z J 0.1 RC-KZ0416CEZZ J 10 VCCCCY1HH220J J 22p VCKYTV1CF105Z J 1.0 VCKYTV1CF105Z J 1.0 VCKYCY1EF104Z J 0.1 RC-KZ0416CEZZ J 10 RC-KZ0416CEZZ J 10 VCKYCY1EF104Z J 0.1 VCKYCY1CF104Z J 0.1 VCKYCY1EF104Z J 0.1 VCKYCY1EF104Z J 0.1 VCKYCY1CF104Z J 0.1 VCKYCY1EF104Z J 0.1 RC-KZ0416CEZZ J 10 VCKYCY1EF104Z J 0.1 RC-KZ0416CEZZ J 10 RC-KZ0416CEZZ J 10 VCKYCY1EF104Z J 0.1 RC-KZ0416CEZZ J 10 VCKYCY1CF104Z J 0.1 RC-KZ0416CEZZ J 10 VCKYCY1EF104Z J 0.1 RC-KZ0416CEZZ J 10 VCKYCY1CF104Z J 0.1 VCKYCY1CF104Z J 0.1 RC-KZ0416CEZZ J 10 VCKYCY1EF104Z J 0.1 VCKYCY1EF104Z J 0.1 RC-KZ0416CEZZ J 10 VCCCCY1HH220J J 22p VCKYTV1CF105Z J 1.0 VCKYTV1CF105Z J 1.0 VCKYCY1CF104Z J 0.1 VCKYCY1EF104Z J 0.1 VCKYCY1EF104Z J 0.1 RC-KZ0416CEZZ J 10 RC-KZ0416CEZZ J 10 VCKYCY1CF104Z J 0.1 VCKYCY1CF104Z J 0.1 VCKYCY1EF104Z J 0.1 VCKYCY1EF104Z J 0.1 VCKYCY1EF104Z J 0.1 VCKYCY1CF104Z J 0.1 VCKYCY1EF104Z J 0.1 RC-KZ0416CEZZ J 10 VCKYCY1EF104Z J 0.1 RC-KZ0416CEZZ J 10 VCKYCY1CF104Z J 0.1 VCKYCY1CF104Z J 0.1 RC-KZ0416CEZZ J 10 VCKYCY1EF104Z J 0.1 RC-KZ0416CEZZ J 10 VCKYCY1CF104Z J 0.1 VCKYCY1CF104Z J 0.1 RC-KZ0416CEZZ J 10 VCKYCY1EF104Z J 0.1 VCKYCY1EF104Z J 0.1 25V 16V 25V 25V 25V 16V 16V 25V 25V 25V 16V 16V 25V 25V 25V 25V 50V 16V 16V 25V 25V 25V 25V 16V 25V 25V 16V 25V 25V 25V 25V 25V 25V 25V 16V 25V 25V 25V 16V 16V 25V 25V 25V 25V 50V 16V 16V 16V 25V 25V 25V 25V 16V 16V 25V 25V 25V 16V 25V 25V 25V 25V 16V 16V 25V 25V 25V 16V 16V 25V 25V 25V Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic AB AG AE AA AE AA AA AE AA AE AA AA AE AA AA AE AA AB AB AA AE AE AA AA AA AA AA AA AE AA AE AE AA AE AA AE AA AE AA AA AE AA AA AE AA AB AB AA AA AA AE AE AA AA AA AA AA AA AA AE AA AE AA AA AE AA AE AA AA AE AA AA XG-C40XU/XE Ref. No. Part No. ★ Description Code Ref. No. AE AA AB AB AA AA AE AE AA AA AA AA AA AA AB AA AE AE AE AF AF AF AE AE AA AA AA AE AE AA AA AA AA AA AA AA AE AE AE AA AB AB AB AC AA AA AA AC AA AA AA AA AB AB AD AE AB AB AA AC AB AA AD AA AD AA AD AA AB AA AB C1485 C1486 C1487 C1488 C1489 C1490 C1491 C1492 C1493 C1494 C1495 C1496 C1497 C1498 C1501 C1502 C1503 C1504 C1505 C1506 C1507 C1508 C1510 C1511 C1541 C1542 C1543 C1544 C1701 C1708 C1709 C1710 C1714 C1715 C1716 C1718 C1719 C1720 C4441 C5001 C5007 C5012 C5015 C5016 C5017 C5033 C5041 C5045 C5046 C5055 C5056 C5057 C5058 C5063 C5064 C5065 C5164 C5165 C5167 C5170 C5171 C5174 C5175 C5176 C5177 C5178 C5179 C5507 C5508 C5509 C5510 C5511 C5512 C5513 C5514 DUNTKA694DE01/02 OUTPUT UNIT (Continued) C1315 C1316 C1317 C1318 C1325 C1326 C1327 C1328 C1340 C1341 C1342 C1343 C1344 C1345 C1346 C1347 C1348 C1349 C1350 C1401 C1402 C1403 C1404 C1405 C1410 C1411 C1412 C1420 C1421 C1422 C1423 C1424 C1425 C1426 C1427 C1429 C1430 C1431 C1432 C1433 C1434 C1435 C1436 C1437 C1438 C1453 C1460 C1461 C1462 C1463 C1464 C1465 C1466 C1467 C1468 C1469 C1470 C1471 C1472 C1473 C1474 C1475 C1476 C1477 C1478 C1479 C1480 C1481 C1482 C1483 C1484 RC-KZ0416CEZZ VCCCCY1HH220J VCKYTV1CF105Z VCKYTV1CF105Z VCKYCY1CF104Z VCKYCY1EF104Z RC-KZ0416CEZZ RC-KZ0416CEZZ VCCCCY1HH471J VCKYCY1CF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1CF104Z VCKYCY1EF104Z VCEAPF1AW476M VCKYCY1EF104Z RC-KZ0416CEZZ RC-KZ0416CEZZ RC-KZ0416CEZZ RC-KZ0074TAZZ RC-KZ0074TAZZ RC-KZ0074TAZZ RC-KZ0416CEZZ RC-KZ0416CEZZ VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z RC-KZ0416CEZZ RC-KZ0416CEZZ VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCCCCY1HH101J VCKYCY1CF104Z RC-KZ0416CEZZ RC-KZ0416CEZZ RC-KZ0416CEZZ VCKYCY1EF104Z VCEAPF1EW226M VCEAPF1EW226M VCEAPF1CW106M VCEAPF0JW107M VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1HB102K VCEAPF1CW476M VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCKYTV1CF105Z VCKYTV1CF105Z VCFRED1HM822J VCFYEC1CM334J VCEAPF1CW106M VCKYCY1CF154Z VCKYCY1CF104Z VCE9PF1CW106M VCEAPF1CW106M VCKYCY1CF104Z VCEAPF1CW107M VCKYCY1CF104Z VCEAPX1EW107M VCKYCY1CF104Z VCEAPF1CW107M VCKYCY1EF104Z VCEAPF1EW336M VCKYCY1CF104Z VCEAPF1CW106M J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 10 22p 1.0 1.0 0.1 0.1 10 10 470p 0.1 0.1 0.1 0.1 0.1 47 0.1 10 10 10 10 10 10 10 10 0.1 0.1 0.1 10 10 0.1 0.1 0.1 0.1 0.1 100p 0.1 10 10 10 0.1 22 22 10 100 0.1 0.1 1000p 47 0.1 0.1 0.1 0.1 1.0 1.0 8200p 0.33 10 0.15 0.1 10 10 0.1 100 0.1 100 0.1 100 0.1 33 0.1 10 25V 50V 16V 16V 16V 25V 25V 25V 50V 16V 25V 25V 16V 25V 10V 25V 25V 25V 25V 25V 25V 25V 25V 25V 16V 16V 16V 25V 25V 16V 16V 16V 16V 16V 50V 16V 25V 25V 25V 25V 25V 25V 16V 6.3V 16V 16V 50V 16V 16V 16V 16V 16V 16V 16V 50V 16V 16V 16V 16V 16V 16V 16V 16V 16V 25V 16V 16V 25V 25V 16V 16V Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Mylar Mylar Electrolytic Ceramic Ceramic Elect.(N.P) Electrolytic Ceramic Electrolytic Ceramic Electrolytic Ceramic Electrolytic Ceramic Electrolytic Ceramic Electrolytic 166 Part No. VCCCCY1HH100D VCCCCY1HH100D VCCCCY1HH100D VCCCCY1HH100D VCCCCY1HH100D VCCCCY1HH100D VCCCCY1HH100D VCCCCY1HH100D VCCCCY1HH220J VCCCCY1HH220J VCCCCY1HH220J VCCCCY1HH560J VCCCCY1HH560J VCCCCY1HH560J RC-KZ0416CEZZ RC-KZ0416CEZZ RC-KZ0416CEZZ VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z RC-KZ0416CEZZ VCCCCY1EH102J VCKYCY1CF104Z VCKYCY1CF104Z VCEAPF0JW107M VCKYCY1CF104Z VCEAPX1EW107M RC-KZ0416CEZZ VCCCCY1HH330J VCCCCY1HH330J VCCCCY1HH330J VCCCCY1HH330J VCCCCY1HH330J VCCCCY1HH330J VCCCCY1HH330J VCCCCY1HH330J VCCCCY1HH330J VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCCCCY1HH101J VCCCCY1HH101J VCCCCY1HH101J VCEAPF0JW476M VCKYCY1CF104Z VCEAPF0JW107M VCKYCY1CF104Z VCEAPF0JW226M VCEAPF0JW476M VCKYCY1HB103K VCEAPF0JW107M VCEAPF1CW107M VCKYCY1CF104Z VCKYCY1CF104Z VCCCCY1HH221J VCKYCY1HB102K VCKYCY1HB102K VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CF104Z RC-KZ0416CEZZ VCKYCY1CF104Z VCKYCY1CF104Z VCCCCY1HH220J VCCCCY1HH220J VCKYCY1CF104Z VCEAPF1CW476M VCKYCY1CF104Z VCKYCY1EF104Z VCEAPF1EW336M VCEAPF1CW107M VCEAPF0JW107M VCKYCY1CF104Z ★ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 10p 10p 10p 10p 10p 10p 10p 10p 22p 22p 22p 56p 56p 56p 10 10 10 0.1 0.1 0.1 0.1 10 1000p 0.1 0.1 100 0.1 100 10 33p 33p 33p 33p 33p 33p 33p 33p 33p 0.1 0.1 0.1 0.1 100p 100p 100p 47 0.1 100 0.1 22 47 0.01 100 100 0.1 0.1 220p 1000p 1000p 0.1 0.1 0.1 10 0.1 0.1 22p 22p 0.1 47 0.1 0.1 33 100 100 0.1 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 25V 25V 25V 16V 16V 16V 16V 25V 25V 16V 16V 6.3V 16V 25V 25V 50V 50V 50V 50V 50V 50V 50V 50V 50V 16V 16V 16V 16V 50V 50V 50V 6.3V 16V 6.3V 16V 6.3V 6.3V 50V 6.3V 16V 16V 16V 50V 50V 50V 16V 16V 16V 25V 16V 16V 50V 50V 16V 16V 16V 25V 25V 16V 6.3V 16V Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Electrolytic Ceramic Electrolytic Electrolytic Ceramic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Ceramic Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AE AE AE AA AA AA AA AE AB AA AA AC AA AD AE AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AC AA AB AB AA AC AD AA AA AA AA AA AA AA AA AE AA AA AA AA AA AC AA AA AB AD AC AA XG-C40XU/XE Ref. No. ★ Part No. Description Code DUNTKA694DE01/02 OUTPUT UNIT (Continued) C5515 C5516 C5530 C5531 C5534 C5535 C5553 C5554 C5555 C5556 C5562 C5564 C5565 C5566 C5568 C5569 C5570 VCEAPF1CW107M VCKYCY1CF104Z VCEAPF1CW226M VCE9PF1CW336M VCEAPF1CW226M VCEAPF1CW226M VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1HB103K VCKYCY1HB103K VCKYCY1HB103K VCEAPF1CW226M VCEAPF1EW336M VCEAPF1CW107M VCEAPF1EW336M VCEAPF1CW107M VCKYCY1CF104Z R1003 R1015 R1016 R1018 R1065 R1066 R1067 R1071 R1081 R1082 R1083 R1084 R1085 R1086 R1087 R1088 R1089 R1090 R1093 R1094 R1095 R1102 R1105 R1108 R1109 R1110 R1113 R1115 R1116 R1117 R1118 R1119 R1120 R1123 R1124 R1125 R1126 R1127 R1128 R1129 R1130 R1131 R1132 R1133 R1134 R1135 R1136 R1137 R1139 R1140 R1141 R1142 VRS-CY1JF103J VRS-TX2HF000J VRS-TX2HF000J QFS-L5015CEZZ VRS-CY1JF153J VRS-CY1JF432J VRS-CY1JF682J VRS-CY1JF101J VRS-CY1JF203J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF203J VRS-CY1JF153J VRS-CY1JF432J VRS-CY1JF682J VRS-CY1JF682J VRS-CY1JF432J VRS-CY1JF153J VRS-CY1JF103J VRS-CY1JF203J VRS-CY1JF101J VRS-CY1JF103J VRS-CY1JF101J VRS-CY1JF000J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF101J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF101J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF102J VRS-CY1JF560J VRS-CY1JF560J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF103J VRS-CY1JF101J VRS-CY1JF101J J J J J J J J J J J J J J J J J J 100 0.1 22 33 22 22 0.1 0.1 0.01 0.01 0.01 22 33 100 33 100 0.1 16V 16V 16V 16V 16V 16V 16V 16V 50V 50V 50V 16V 25V 16V 25V 16V 16V Electrolytic Ceramic Electrolytic Elect.(N.P) Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Ceramic AD AA AB AD AB AB AA AA AA AA AA AB AB AD AB AD AA RESISTORS J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 10k 0 0 15k 4.3k 6.8k 100 20k 10k 10k 20k 15k 4.3k 6.8k 6.8k 4.3k 15k 10k 20k 100 10k 100 0 1.0k 1.0k 100 0 0 100 0 0 0 100 100 0 0 0 0 0 0 1.0k 56 56 0 0 0 0 0 10k 100 100 1/16W Metal Oxide 1/2W Metal Oxide 1/2W Metal Oxide Fuse Resistor 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide AA AA AA AD AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 167 Ref. No. Part No. ★ R1143 R1144 R1145 R1146 R1147 R1148 R1152 R1154 R1155 R1159 R1160 R1166 R1167 R1168 R1171 R1172 R1173 R1174 R1175 R1176 R1179 R1180 R1181 R1193 R1194 R1201 R1202 R1206 R1209 R1210 R1214 R1215 R1216 R1218 R1219 R1220 R1223 R1224 R1225 R1226 R1227 R1228 R1229 R1230 R1231 R1234 R1235 R1236 R1237 R1239 R1240 R1241 R1242 R1243 R1244 R1245 R1246 R1247 R1248 R1249 R1254 R1255 R1256 R1259 R1261 R1262 R1271 R1272 R1273 R1274 R1275 R1276 R1279 R1280 R1281 VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF101J VRS-TV1JD270J VRS-CY1JF272J VRS-CY1JF222J VRS-CY1JF222J VRS-CY1JF222J VRS-CY1JF3R3J VRS-CY1JF3R3J VRS-CY1JF3R3J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF000J VRS-CY1JF470J VRS-CY1JF101J VRS-CY1JF103J VRS-CY1JF101J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF101J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF102J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF103J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF101J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF222J VRS-CY1JF222J VRS-CY1JF3R3J VRS-CY1JF3R3J VRS-CY1JF3R3J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF101J VRS-CY1JF101J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 0 0 0 0 0 0 0 0 0 0 100 27 2.7k 2.2k 2.2k 2.2k 3.3 3.3 3.3 0 0 100 100 0 47 100 10k 100 1.0k 1.0k 100 0 0 0 0 0 100 100 0 0 0 0 0 0 1.0k 0 0 0 0 0 10k 100 100 0 0 0 0 0 0 0 0 0 100 0 0 0 2.2k 2.2k 3.3 3.3 3.3 0 0 100 100 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA XG-C40XU/XE Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA R1416 R1417 R1418 R1419 R1420 R1421 R1422 R1423 R1424 R1425 R1426 R1427 R1428 R1429 R1430 R1431 R1432 R1433 R1434 R1435 R1436 R1437 R1438 R1440 R1441 R1442 R1443 R1444 R1447 R1448 R1449 R1450 R1451 R1452 R1453 R1454 R1455 R1456 R1457 R1458 R1460 R1464 R1466 R1467 R1468 R1469 R1470 R1471 R1472 R1473 R1474 R1475 R1476 R1477 R1480 R1486 R1490 R1491 R1492 R1493 R1494 R1495 R1496 R1497 R1498 R1499 R1501 R1502 R1503 R1504 R1505 R1506 R1507 R1508 R1509 VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF272J VRS-CY1JF103J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF470J VRS-CY1JF101J VRS-CY1JF000J VRS-TV1JD121J VRS-TV1JD121J VRS-CY1JF121J VRS-CY1JF121J VRS-CY1JF102J VRS-CY1JF472J VRS-CY1JF102J VRS-CY1JF472J VRS-CY1JF220F VRS-CY1JF220F VRS-CY1JF560J VRS-CY1JF560J VRS-CY1JF560J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF000J VRS-CY1JF222J VRS-CY1JF101J VRS-CY1JF202J VRS-CY1JF302J VRS-CY1JF392J VRS-CY1JF101J VRS-CY1JF103J VRS-CY1JF392J VRS-CY1JF392J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF103J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF123F VRS-CY1JF102F VRS-CY1JF510F VRS-TX2HF000J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF222J VRS-TX2HF5R6J VRS-CY1JF104J VRS-CY1JF104J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF473J VRS-CY1JF000J VRS-CY1JF222J VRS-CY1JF102J VRS-CY1JF561J VRS-CY1JF101J VRS-CY1JF471J VRS-CY1JF222J VRS-CY1JF102J VRS-CY1JF561J VRS-CY1JF101J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J DUNTKA694DE01/02 OUTPUT UNIT (Continued) R1294 R1301 R1302 R1306 R1309 R1310 R1313 R1314 R1315 R1316 R1318 R1319 R1320 R1323 R1324 R1325 R1326 R1327 R1328 R1329 R1330 R1331 R1332 R1333 R1334 R1335 R1336 R1337 R1339 R1340 R1341 R1342 R1343 R1344 R1345 R1346 R1347 R1348 R1349 R1354 R1355 R1356 R1359 R1361 R1362 R1366 R1367 R1368 R1371 R1372 R1373 R1374 R1375 R1376 R1379 R1380 R1381 R1394 R1401 R1402 R1403 R1404 R1405 R1406 R1407 R1408 R1409 R1412 R1413 R1414 R1415 VRS-CY1JF470J VRS-CY1JF101J VRS-CY1JF103J VRS-CY1JF101J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF000J VRS-CY1JF101J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF102J VRS-CY1JF560J VRS-CY1JF560J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF103J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF101J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-TV1JD270J VRS-CY1JF272J VRS-CY1JF222J VRS-CY1JF222J VRS-CY1JF222J VRS-CY1JF3R3J VRS-CY1JF3R3J VRS-CY1JF3R3J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF470J VRN-CY1JF560D VRN-CY1JF560D VRN-CY1JF560D VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF181J VRS-CY1JF181J VRS-CY1JF181J VRS-CY1JF332J VRS-CY1JF332J VRS-CY1JF332J VRS-CY1JF101J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 47 100 10k 100 1.0k 1.0k 0 100 0 0 0 0 0 100 100 0 0 0 0 0 0 1.0k 56 56 0 0 0 0 0 10k 100 100 0 0 0 0 0 0 0 0 0 100 0 0 0 27 2.7k 2.2k 2.2k 2.2k 3.3 3.3 3.3 0 0 100 100 47 56 56 56 10k 10k 10k 180 180 180 3.3k 3.3k 3.3k 100 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Film 1/16W Metal Film 1/16W Metal Film 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 168 Description 100 100 100 100 100 0 0 2.7k 10k 0 0 0 47 100 0 120 120 120 120 1.0k 4.7k 1.0k 4.7k 22 22 56 56 56 100 100 10k 10k 0 2.2k 100 2.0k 3.0k 3.9k 100 10k 3.9k 3.9k 100 100 100 10k 100 100 10k 10k 12k 1.0k 51 0 100 100 10k 10k 2.2k 5.6 100k 100k 1.0k 1.0k 47k 0 2.2k 1.0k 560 100 470 2.2k 1.0k 560 100 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/2W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/2W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA XG-C40XU/XE Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA R1705 R1709 R1711 R1713 R1717 R1721 R1723 R1725 R1729 R1733 R1735 R1740 R1741 R1742 R1743 R1744 R1745 R1746 R1747 R1748 R1749 R1750 R1751 R1752 R1753 R1754 R1755 R1756 R1757 R1758 R1760 R1761 R1762 R1763 R1764 R1765 R1766 R1767 R1768 R1769 R1770 R1771 R1772 R1773 R1774 R1775 R1776 R1777 R1778 R1779 R1780 R1781 R1782 R1783 R1784 R1785 R1786 R1787 R1788 R1789 R1790 R5003 R5004 R5005 R5006 R5008 R5010 R5011 R5012 R5013 R5016 R5017 R5018 R5022 R5023 VRS-CB1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CB1JF100J VRS-CB1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CB1JF100J VRS-CB1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF222J VRS-CY1JF3R3J VRS-CY1JF3R3J VRS-CY1JF101J VRS-CY1JF222J VRS-CY1JF3R3J VRS-CY1JF222J VRS-CY1JF3R3J VRS-CY1JF3R3J VRS-CY1JF101J VRS-CY1JF222J VRS-CY1JF3R3J VRS-CY1JF222J VRS-CY1JF3R3J VRS-CY1JF3R3J VRS-CY1JF101J VRS-CY1JF3R3J VRS-CY1JF222J VRS-CY1JF000J VRS-CY1JF223J VRS-CY1JF103J VRS-CY1JF153J VRS-CY1JF153J VRS-CY1JF153J VRS-CY1JF153J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF000J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF101J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF101J VRS-CY1JF103J VRS-CY1JF101J VRS-CY1JF103J VRS-CY1JF101J VRS-TX2HF3R9J VRS-TX2HF3R9J VRS-TX2HF3R9J VRS-CY1JF102J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J DUNTKA694DE01/02 OUTPUT UNIT (Continued) R1510 R1511 R1515 R1517 R1518 R1522 R1523 R1524 R1525 R1526 R1527 R1528 R1532 R1533 R1534 R1535 R1536 R1537 R1538 R1539 R1540 R1541 R1542 R1543 R1544 R1545 R1546 R1549 R1550 R1551 R1557 R1558 R1559 R1561 R1562 R1563 R1565 R1566 R1567 R1568 R1575 R1576 R1586 R1602 R1606 R1607 R1608 R1609 R1610 R1611 R1612 R1613 R1626 R1627 R1628 R1629 R1630 R1632 R1633 R1634 R1635 R1636 R1637 R1648 R1650 R1651 R1653 R1654 R1657 R1658 R1701 VRS-CY1JF471J VRS-CY1JF222J VRS-TX2HF100J VRS-CY1JF000J VRS-CY1JF272J VRS-CY1JF102J VRS-CY1JF561J VRS-CY1JF101J VRS-CY1JF471J VRS-CY1JF222J VRS-CY1JF821J VRS-CY1JF222J VRS-CY1JF821J VRS-CY1JF222J VRS-CY1JF152J VRS-CY1JF822J VRS-CY1JF222J VRS-CY1JF821J VRS-CY1JF221J VRS-CY1JF471J VRS-CY1JF681J VRS-CY1JF221J VRS-CY1JF681J VRS-CY1JF471J VRS-CY1JF221J VRS-CY1JF471J VRS-CY1JF681J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF682J VRS-CY1JF104J VRS-CY1JF104J VRN-CY1JF562D VRS-CY1JF470J VRS-CY1JF470J VRS-CY1JF470J VRS-CY1JF103J VRS-CY1JF000J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-TV1JD000J VRS-CY1JF183J VRS-CY1JF000J VRS-CY1JF333J VRS-CY1JF000J VRS-CY1JF393J VRS-CY1JF393J VRS-CB1JF100J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 470 2.2k 10 0 2.7k 1.0k 560 100 470 2.2k 820 2.2k 820 2.2k 1.5k 8.2k 2.2k 820 220 470 680 220 680 470 220 470 680 0 0 0 0 0 0 0 0 6.8k 100k 100k 5.6k 47 47 47 10k 00 1.0k 1.0k 1.0k 1.0k 1.0k 1.0k 1.0k 1.0k 10k 10k 10k 10k 10k 10k 10k 10k 10k 10k 10k 0 18k 0 33k 0 39k 39k 10 1/16W 1/16W 1/2W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Film Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide 169 Description 10 10 10 10 10 10 10 10 10 10 10 2.2k 3.3 3.3 100 2.2k 3.3 2.2k 3.3 3.3 100 2.2k 3.3 2.2k 3.3 3.3 100 3.3 2.2k 0 22k 10k 15k 15k 15k 15k 10k 10k 0 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 1.0k 1.0k 100 10k 10k 100 10k 100 10k 100 3.9 3.9 3.9 1.0k 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/2W Metal Oxide 1/2W Metal Oxide 1/2W Metal Oxide 1/16W Metal Oxide Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AB AA XG-C40XU/XE Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA R5176 R5177 R5178 R5179 R5181 R5182 R5183 R5184 R5185 R5186 R5187 R5188 R5189 R5190 R5191 R5192 R5193 R5194 R5195 R5196 R5197 R5198 R5199 R5200 R5201 R5202 R5204 R5205 R5206 R5506 R5507 R5509 R5510 R5512 R5513 R5514 R5515 R5516 R5517 R5518 R5519 R5520 R5521 R5522 R5523 R5524 R5525 R5526 R5527 R5528 R5529 R5530 R5536 R5537 R5538 R5539 R5540 R5544 R5545 R5546 R5547 R5550 R5551 R5552 R5553 R5554 R5555 R5557 R5570 R5571 R5578 R5579 R5580 R5590 R5592 VRS-CY1JF104J VRS-CY1JF101J VRS-CY1JF104J VRS-CY1JF104J VRS-CY1JF104J VRS-CY1JF100J VRS-CY1JF104J VRS-CY1JF104J VRS-CY1JF104J VRS-CY1JF104J VRS-CB1JF104J VRS-CB1JF100J VRS-CY1JF104J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF104J VRS-CY1JF104J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF000J VRS-CY1JF103J VRS-CY1JF332J VRS-CY1JF104J VRN-CY1JF123D VRS-TX2HF2R2J VRS-TX2HF2R2J VRS-CB1JF102J VRS-CY1JF103J VRS-CY1JF101J VRS-CY1JF103J VRS-TQ2BD000J VRS-TQ2BD000J VRS-TQ2BD000J VRS-TQ2BD000J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF000J VRS-CY1JF103J VRS-CY1JF273J VRN-CY1JF183D VRS-CY1JF224J VRN-CY1JF362D VRS-CY1JF472J VRS-CY1JF392J VRS-CY1JF472J VRS-CY1JF821J VRS-CY1JF332J VRS-CY1JF102J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF512F VRS-CY1JF362F VRS-CY1JF103J VRS-CY1JF000J VRS-CY1JF393J VRS-CY1JF101J VRS-CY1JF223J VRS-CY1JF223J VRS-CY1JF103J VRS-CY1JF102J VRS-TV1JD000J VRS-CY1JF101J VRN-CY1JF273D VRS-CY1JF222F VRS-CY1JF153F VRS-CY1JF224F VRS-CY1JF102J VRS-CY1JF103J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J DUNTKA694DE01/02 OUTPUT UNIT (Continued) R5024 R5031 R5032 R5035 R5036 R5037 R5038 R5039 R5040 R5041 R5042 R5043 R5044 R5045 R5046 R5047 R5048 R5053 R5055 R5074 R5075 R5076 R5081 R5082 R5084 R5093 R5099 R5105 R5106 R5107 R5108 R5109 R5110 R5111 R5112 R5113 R5114 R5121 R5125 R5126 R5127 R5128 R5129 R5130 R5133 R5135 R5140 R5142 R5146 R5147 R5150 R5151 R5152 R5153 R5155 R5157 R5159 R5161 R5162 R5163 R5164 R5165 R5167 R5168 R5169 R5170 R5171 R5172 R5173 R5174 R5175 VRS-TX2HF3R9J VRS-CY1JF000J VRS-CY1JF103J VRS-CY1JF103J VRS-TW2ED470J VRS-CY1JF103J VRS-TW2ED101J VRS-CY1JF103J VRS-TW2ED221J VRS-CY1JF103J VRS-TW2ED221J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-TW2ED221J VRS-CY1JF103J VRS-TX2HF220J VRS-CA1JF101J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF103J VRS-CY1JF101J VRS-CY1JF471J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-TW2ED000J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF272J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF272J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF272J VRS-CY1JF272J VRN-CY1JF682D VRN-CY1JF222D VRS-CY1JF103J VRS-CY1JF102J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF272J VRS-CY1JF101J VRS-CY1JF222J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-TV1JD000J VRS-TV1JD000J VRS-TV1JD000J VRS-CY1JF100J VRS-CY1JF562J VRS-CY1JF562J VRS-CY1JF101J VRS-CY1JF101J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 3.9 0 10k 10k 47 10k 100 10k 220 10k 220 10k 10k 10k 220 10k 22 100 1.0k 1.0k 1.0k 1.0k 100 100 10k 100 470 100 100 100 100 100 100 100 0 100 100 2.7k 0 0 0 2.7k 0 0 2.7k 2.7k 6.8k 2.2k 10k 1.0k 100 100 100 100 100 2.7k 100 2.2k 0 0 0 0 0 0 0 0 10 5.6k 5.6k 100 100 1/2W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/4W Metal Oxide 1/16W Metal Oxide 1/4W Metal Oxide 1/16W Metal Oxide 1/4W Metal Oxide 1/16W Metal Oxide 1/4W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/4W Metal Oxide 1/16W Metal Oxide 1/2W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/4W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Film 1/16W Metal Film 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 170 Description 100k 100 100k 100k 100k 10 100k 100k 100k 100k 100k 10 100k 10 10 10 10 10 10 100k 100k 10 10 10 0 10k 3.3k 100k 12k 2.2 2.2 1.0k 10k 100 10k 0 0 0 0 100 100 100 100 0 10k 27k 18k 220k 3.6k 4.7k 3.9k 4.7k 820 3.3k 1.0k 10k 10k 5.1k 3.6k 10k 0 39k 100 22k 22k 10k 1.0k 0 100 27k 2.2k 15k 220k 1.0k 10k 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Film 1/2W Metal Oxide 1/2W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/8W Metal Oxide 1/8W Metal Oxide 1/8W Metal Oxide 1/8W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Film 1/16W Metal Oxide 1/16W Metal Film 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Film 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AC AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA XG-C40XU/XE Ref. No. ★ Part No. Description Code OUTPUT UNIT (Continued) VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF471J VRS-TX2HF2R2J VRS-CY1JF103J VRS-CY1JF222F VRS-CY1JF183F VRS-CY1JF393F VRS-CY1JF472J VRS-TX2HF2R2J VRS-CY1JF682J VRS-CY1JF562J VRS-TX2HF2R2J VRS-TX2HF2R2J VRS-CY1JF103J VRS-CY1JF153F VRS-CY1JF222F VRS-CY1JF683F VRS-CY1JF103J VRS-CY1JF223J VRS-CY1JF393J VRN-CY1JF272D VRN-CY1JF101D VRS-CY1JF102J VRS-CY1JF102J J J J J J J J J J J J J J J J J J J J J J J J J J J J 10k 10k 10k 10k 470 2.2 10k 2.2k 18k 39k 4.7k 2.2 6.8k 5.6k 2.2 2.2 10k 15k 2.2k 68k 10k 22k 39k 2.7k 100 1.0k 1.0k 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/2W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/2W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/2W Metal Oxide 1/2W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Film 1/16W Metal Film 1/16W Metal Oxide 1/16W Metal Oxide ★ Part No. FB5518 RBLN-0065CEZZ FB5519 RBLN-0065CEZZ FB5521 RBLN-0062CEZZ P5501 QPLGN0174FJZZ P5502 QPLGN0763TAZZ P5503 QPLGN0264TAZZ P5504 QPLGN0174FJZZ P5505 QPLGN0176FJZZ P5506 QPLGN0176FJZZ P5507 QPLGN0364TAZZ P5508 QPLGN0464TAZZ P5509 QPLGN0436FJZZ P5510 QPLGN0564TAZZ P5511 QPLGN0175FJZZ SC1101 QSOCN3071TAZZ SC1201 QSOCN3071TAZZ SC1301 QSOCN3071TAZZ SC1404 QCNCW6054TAZZ SC1405 QCNCW6054TAZZ SC1501 QSOCZ2058CEZZ SC1502 QSOCZ2058CEZZ SC5001 QSOCN1897REZZ SC5502 QCNCW6054TAZZ RMC7502 RRMCU0237CEZZ PSLDC3076CEFN DUNTKA694DE01/02 R5593 R5594 R5595 R5596 R5597 R5598 R5599 R5600 R5601 R5602 R5603 R5604 R5619 R5620 R5621 R5622 R5623 R5624 R5625 R5626 R5628 R5629 R5630 R5631 R5632 R5636 R5637 Ref. No. AA AA AA AA AA AB AA AA AA AA AA AB AA AA AB AB AA AA AA AA AA AA AA AB AB AA AA J J J J J J J J J J J J J J J J J J J J J J J J J Description Frrite Bead Frrite Bead Frrite Bead Plug 2-Pin Plug 7-Pin Plug 2-Pin Plug 2-Pin Plug 4-Pin Plug 4-Pin Plug 3-Pin Plug 8-Pin Plug 28-Pin Plug 5-Pin Plug 3-Pin Socket 30-Pin (R) Socket 30-Pin (G) Socket 30-Pin (B) Socket 60-Pin Socket 60-Pin Socket 20-Pin Socket 20-Pin Socket 18-Pin Socket 60-Pin R/C Receiver Sheild Code AB AB AC AC AD AC AC AD AD AC AC AE AC AD AE AE AE AK AK AG AG AE AK AF AE SWITCH SW5101QSW-K0065GEZZ J Key Switch AC DUNTK9769DE24/25 MISCELLANEOUS PARTS F1401 F1601 FB1101 FB1102 FB1104 FB1105 FB1107 FB1108 FB1109 FB1201 FB1202 FB1204 FB1205 FB1206 FB1301 FB1302 FB1304 FB1305 FB1306 FB1401 FB1402 FB1405 FB1511 FB5001 FB5101 FB5501 FB5502 FB5504 FB5505 FB5507 FB5508 FB5509 FB5510 FB5512 FB5513 FB5514 FB5515 FB5516 FB5517 QFS-L8012CEZZ QFS-L8012CEZZ RBLN-0059CEZZ RBLN-0059CEZZ RBLN-0059CEZZ RBLN-0059CEZZ RBLN-0059CEZZ RBLN-0067CEZZ RBLN-0067CEZZ RBLN-0059CEZZ RBLN-0059CEZZ RBLN-0059CEZZ RBLN-0059CEZZ RBLN-0059CEZZ RBLN-0059CEZZ RBLN-0059CEZZ RBLN-0059CEZZ RBLN-0059CEZZ RBLN-0059CEZZ RBLN-0059CEZZ RBLN-0059CEZZ RBLN-0059CEZZ RBLN-0065CEZZ RBLN-0062CEZZ RBLN-0059CEZZ RBLN-0062CEZZ RBLN-0062CEZZ RBLN-0065CEZZ RBLN-0065CEZZ RBLN-0062CEZZ RBLN-0062CEZZ RBLN-0062CEZZ RBLN-0062CEZZ RBLN-0065CEZZ RBLN-0065CEZZ RBLN-0065CEZZ RBLN-0065CEZZ RBLN-0067CEZZ RBLN-0067CEZZ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Fuse 0.8A Fuse 0.8A Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead VIDEO UNIT AF AF AB AB AB AB AB AC AC AB AB AB AB AB AB AB AB AB AB AB AB AB AB AC AB AC AC AB AB AC AC AC AC AB AB AB AB AC AC INTEGRATED CIRCUITS IC6001 VHiNJM2245M-1 IC6004 VHiMC141627-1 J NJM2245M J MC141627FT AF AY TRANSISTORS Q6002 Q6003 Q6004 Q6008 Q6009 Q6010 Q6013 Q6015 VS2SA1530AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SC3928AR-1 VS2SA1530AR-1 VS2SC3928AR-1 VSiMX2/////-1 J J J J J J J J D6001 D6007 D6009 D6010 RH-EX0226CEZZ VHDMA153///-1 VHD1SS355//-1 RH-EX0228CEZZ FL6002 FL6003 FL6004 FL6005 FL6006 FL6011 FL6012 L6001 L6002 L6003 RFiLN0124GEZZ RFiLN0124GEZZ RFiLN0124GEZZ RFiLN0124GEZZ RFiLN0124GEZZ RCiLF0316CEZZ RCiLF0316CEZZ VP-1M270J3R8N VP-1M330J4R2N VP-1M330J4R2N C6001 C6005 C6013 C6014 VCEAPF1CW106M VCEAPF1CW226M VCKYCY1CF104Z VCEAPF1CW106M 2SA1530AR 2SC3928AR 2SC3928AR 2SC3928AR 2SC3928AR 2SA1530AR 2SC3928AR iMX2 AB AB AB AB AB AB AB AB DIODES J J J J Zener Diode Diode Diode Zener Diode AB AB AB AB FILTERS AND COILS J J J J J J J J J J Filter Filter Filter Filter Filter Filter Filter Peaking 27µH Peaking 33µH Peaking 33µH AD AD AD AD AD AG AG AC AC AC CAPACITORS 171 J J J J 10 22 0.1 10 16V 16V 16V 16V Electrolytic Electrolytic Ceramic Electrolytic AB AB AA AB XG-C40XU/XE Ref. No. ★ Part No. Description Code Ref. No. R6095 VRS-CY1JF103J R6096 VRS-CY1JF101J DUNTK9769DE24/25 VIDEO UNIT (Continued) C6015 C6016 C6017 C6018 C6019 C6020 C6021 C6022 C6023 C6024 C6025 C6026 C6027 C6029 C6030 C6031 C6035 C6037 C6038 C6039 C6040 C6041 C6042 C6043 C6044 C6045 VCKYCY1CF104Z VCKYCY1CF104Z VCEAPF0JW476M VCKYCY1CF104Z VCEAPF1CW106M VCKYCY1CF104Z VCEAPF1CW106M VCEAPF1HW105M VCCCCY1HH270J VCCCCY1HH270J VCEAPF1CW226M VCCCCY1HH101J VCE9PF1HW105M VCKYCY1HB103K VCEAPF1HW105M VCKYCY1CF104Z VCKYCY1CF104Z VCEAPF0JW226M VCEAPF0JW226M VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1HB103K VCKYCY1CF104Z VCKYCY1HB103K J J J J J J J J J J J J J J J J J J J J J J J J J J 0.1 0.1 47 0.1 10 0.1 10 1.0 27p 27p 22 100p 1.0 0.01 1.0 0.1 0.1 22 22 0.1 0.1 0.1 0.1 0.01 0.1 0.01 16V 16V 6.3V 16V 16V 16V 16V 50V 50V 50V 16V 50V 50V 50V 50V 16V 16V 6.3V 6.3V 25V 25V 16V 16V 50V 16V 50V Ceramic Ceramic Electrolytic Ceramic Electrolytic Ceramic Electrolytic Electrolytic Ceramic Ceramic Electrolytic Ceramic Elect.(N.P) Ceramic Electrolytic Ceramic Ceramic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Part No. ★ Description J 10k J 100 1/16W Metal Oxide 1/16W Metal Oxide Code AA AA MISCELLANEOUS PARTS AA AA AB AA AB AA AB AB AA AA AB AA AC AA AB AA AA AB AB AA AA AA AA AA AA AA FB6001 RBLN-0067CEZZ FB6013 RBLN-0059CEZZ FB6014 RBLN-0059CEZZ FB6015 RBLN-0059CEZZ FB6016 RBLN-0059CEZZ FB6017 RBLN-0059CEZZ FB6019 RBLN-0062CEZZ FB6020 RBLN-0062CEZZ FB6021 RBLN-0062CEZZ FB6022 RBLN-0062CEZZ J6001 QJAKG0049CEZZ J6003 QSOCD0403GEZZ SC6001 QSOCZ3043CEZZ PSLDM4519CEFW QEARP0093CEFN J J J J J J J J J J J J J J J Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Frrite Bead Jack (AV-In) Jack (S-Video-In) Socket 30-Pin (VS) Sheild Sheild AC AB AB AB AB AB AC AC AC AC AH AE AG AK AE RUNTK0677CEZZ INLET UNIT PACKAGED CIRCUIT RESISTORS R6001 R6002 R6003 R6004 R6005 R6006 R6008 R6011 R6047 R6049 R6050 R6051 R6052 R6053 R6054 R6055 R6056 R6057 R6058 R6059 R6060 R6061 R6062 R6063 R6064 R6069 R6070 R6071 R6072 R6073 R6074 R6075 R6076 R6081 R6082 R6085 R6087 R6088 R6089 R6090 R6091 R6092 R6094 VRS-CY1JF100J VRS-TQ2BD750J VRS-TQ2BD750J VRS-CY1JF100J VRS-TQ2BD750J VRS-CY1JF101J VRS-CY1JF123J VRS-CY1JF4R7J VRS-CY1JF473J VRS-CY1JF101J VRS-CY1JF560J VRS-CY1JF473J VRS-CY1JF103J VRS-CY1JF754J VRS-CY1JF473J VRS-CY1JF560J VRS-TV1JD152J VRS-CY1JF102J VRS-CY1JF273J VRS-CY1JF273J VRS-CY1JF102J VRS-CY1JF560J VRS-CY1JF102J VRS-CY1JF393J VRS-CY1JF393J VRS-CY1JF102J VRS-CY1JF153J VRS-CY1JF152J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF153J VRS-CY1JF332J VRS-CY1JF185J VRS-CY1JF563J VRS-CY1JF121J VRS-TQ2BD000J VRS-TQ2BD000J VRS-CY1JF123J VRS-CY1JF101J VRS-CY1JF224J VRS-CY1JF224J VRS-CY1JF392J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 10 75 75 10 75 100 12k 4.7 47k 100 56 47k 10k 750k 47k 56 1.5k 1.0k 27k 27k 1.0k 56 1.0k 39k 39k 1.0k 15k 1.5k 1.0k 1.0k 1.0k 15k 3.3k 1.8M 56k 120 0 0 12k 100 220k 220k 3.9k 1/16W Metal Oxide 1/8W Metal Oxide 1/8W Metal Oxide 1/16W Metal Oxide 1/8W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/8W Metal Oxide 1/8W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA å TNR761 9FJ0F20001280 å å L761 L762 L763 9FJ0L05001460 9FJ0L05001460 9FJ0L08001660 å å å å å å å C761 C762 C763 C764 C765 C766 C767 9FJ0C34001763 9FJ0C51001223 9FJ0C51001223 9FJ0C34001753 9FJ0C34001763 9FJ0C34001763 9FJ0C34001763 å R761 9FJ0R11002110 å F761 9FJ0E02101020 9FJ0G10003930 J ENE471D10A AD COILS J ADR18-03-030Y J ADR18-03-030Y J AFP10-60-080 AN AN AG CAPACITORS J J J J J J J 0.22 1000p 1000p 0.1 0.22 0.22 0.22 250V 250V 250V 250V 250V 250V 250V M.Polyester Ceramic Ceramic M.Polyester M.Polyester M.Polyester M.Polyester AF AD AD AE AF AF AF RESISTOR J 470k 1/2W AC MISCELLANEOUS PARTS J Fuse 5A 250V AG J Connector, 3-pin (PF) S2P3-VH AD RDENC0334CEZZ POWER UNIT INTEGRATED CIRCUITS å å IC701 IC702 IC703 9FJ0F01901370 9FJ0F09001050 9FJ0F01102505 Q701 Q702 Q703 Q704 Q705 9FJ0Q02001725 9FJ0Q11001592 9FJ0D40010160 9FJ0Q11010692 9FJ0Q00001065 J FA5332P J FA5315P J HA17431VLPEL AW AN AF TRANSISTORS 172 J J J J J 2SC4409 2SK2837 TF561S 2SK2605 2SA1162YT AE AU AK AR AC XG-C40XU/XE Ref. No. ★ Part No. Description Code R701 R702 R703 R704 R705 R706 R707 R708 R709 R710 R711 R712 R713 R714 R715 R716 R718 R719 R720 R721 R722 R723 R724 R725 R726 R727 R728 R729 R730 R731 R733 R734 R735 R736 R737 R738 R739 R740 R741 R742 R743 R744 R745 R746 R747 R748 R749 R750 R753 R754 R755 R756 R757 R758 R759 R770 R771 POWER UNIT(Continued) DIODES D701 D702 D703 D704 D705 D706 D707 D708 D709 D710 D711 D712 D713 ZD701 ZD702 ZD703 ZD704 ZD705 9FJ0D14000122 9FJ0D01010035 9FJ0D00001005 9FJ0D01010035 9FJ0D01010035 9FJ0D01001555 9FJ0D24001240 9FJ0D01010035 9FJ0D01010035 9FJ0D01010035 9FJ0D24001230 9FJ0D03001113 9FJ0D23010022 9FJ0D31181695 9FJ0D31181695 9FJ0D31181695 9FJ0D31181695 9FJ0D31110125 å å å PC701 9FJ0F10010931 PC702 9FJ0F10010931 PC703 9FJ0F10010931 J J J J J J J J J J J J J J J J J J Diode RBV-606 Diode TVR5JTPA Diode 1SS119T Diode TVR5JTPA Diode TVR5JTPA Diode AK03V0 Diode SF10L60U Diode TVR5JTPA Diode TVR5JTPA Diode TVR5JTPA Diode SF10SC6 Diode S3L20U Diode FMX12S Zener Diode RD24JSAB2TA Zener Diode RD24JSAB2TA Zener Diode RD24JSAB2TA Zener Diode RD24JSAB2TA Zener Diode RD5.1JSAB2TA AK AC AB AC AC AD AG AC AC AC AK AG AH AC AC AC AC AD PACKAGED CIRCUITS J Photo Coupler TLP721FD4GR AG J Photo Coupler TLP721FD4GR AG J Photo Coupler TLP721FD4GR AG COILS AND TRANSFORMER L701 L702 L703 L704 å T701 9FJ0L08001850 9FJ0L08001025 9FJ0L08001025 9FJ0L08001025 9FJ0L00501170 J J J J J Inductor THNW23-06251 Inductor B-01-AT Inductor B-01-AT Inductor B-01-AT Transformer 050117 AY AC AC AC AT CONTROL VR701 9FJ0R60001255 J 1k EVNDXAA03B13 AE CAPACITORS C701 C702 C703 C704 C705 C706 C707 C708 C709 C710 C711 C712 C713 C714 å C716 C717 C718 C719 C720 C721 C722 C723 C724 C725 C726 C727 C728 C729 C730 C731 å C732 C733 C734 9FJ0C32410040 9FJ0C50004335 9FJ0C01401985 9FJ0C01502455 9FJ0C50003455 9FJ0C02801643 9FJ0C50002015 9FJ0C50004365 9FJ0C50004375 9FJ0C50011465 9FJ0C50002635 9FJ0C50011465 9FJ0C50002015 9FJ0C50004365 9FJ0C51001223 9FJ0C50002015 9FJ0C21201035 9FJ0C50010715 9FJ0C50004325 9FJ0C50011465 9FJ0C50002635 9FJ0C50002635 9FJ0C01401635 9FJ0C50002985 9FJ0C01102040 9FJ0C01102040 9FJ0C50003745 9FJ0C50002985 9FJ0C01302155 9FJ0C01302140 9FJ0C51001223 9FJ0C50004335 9FJ0C01510195 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 2.2 0.22 100 22 470p 150 0.01 0.15 68p 470p 0.047 470p 0.01 0.15 1000p 0.01 4700p 220p 0.22 470p 0.047 0.047 47 1000p 1000 1000 0.1 1000p 220 470 1000p 0.22 3.3 400V 25V 35V 50V 1kV 420V 50V 25V 50V 50V 50V 50V 50V 25V 4kV 50V 200V 1kV 16V 50V 50V 50V 35V 500V 10V 10V 50V 500V 25V 25V 4kV 25V 50V M.Polyester Ceramic (Chip) Electrolytic Electrolytic Ceramic Electrolytic Ceramic Ceramic (Chip) Ceramic (Chip) Ceramic (Chip) Ceramic Ceramic (Chip) Ceramic Ceramic (Chip) Ceramic Ceramic Ceramic Ceramic Ceramic (Chip) Ceramic (Chip) Ceramic Ceramic Electrolytic Ceramic Electrolytic Electrolytic Ceramic (Chip) Ceramic Electrolytic Electrolytic Ceramic Ceramic (Chip) Electrolytic ★ Part No. Description Code RESISTORS RDENC0334CEZZ å Ref. No. AN AD AE AC AK AT AB AC AC AC AC AC AB AC AD AB AF AD AD AC AC AC AD AD AF AF AC AD AE AF AD AD AD 9FJ0R94201715 9FJ0R94201715 9FJ0R91201445 9FJ0R94201005 9FJ0R17070491 9FJ0R70010070 9FJ0R22110330 9FJ0R94201305 9FJ0R91201245 9FJ0R91501065 9FJ0R91501065 9FJ0R91501065 9FJ0R91501025 9FJ0R91501065 9FJ0R91501065 9FJ0R91501065 9FJ0R91501005 9FJ0R91501065 9FJ0R91501065 9FJ0R91501065 9FJ0R91501005 9FJ0R91201505 9FJ0R91201425 9FJ0R91201455 9FJ0R91201365 9FJ0R91201055 9FJ0R91201405 9FJ0R91201485 9FJ0R92201115 9FJ0R91201005 9FJ0R94201715 9FJ0R94201715 9FJ0R91201445 9FJ0R91201665 9FJ0R91201245 9FJ0R91201105 9FJ0R91201005 9FJ0R93201125 9FJ0R93201005 9FJ0R91201365 9FJ0R94001095 9FJ0R17071411 9FJ0R91201245 9FJ0R91201165 9FJ0R91201665 9FJ0R91201305 9FJ0R91201305 9FJ0R91201125 9FJ0R94201305 9FJ0R94201715 9FJ0R94201715 9FJ0R16080255 9FJ0R94201285 9FJ0R91201285 9FJ0R91201265 9FJ0R94201715 9FJ0R94201715 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 9.1k 1/2W 9.1k 1/2W 47k 1/10W 10 1/2W 10 2W 10 5W 0.1 5W 3.3k 1/2W 1k 1/10W 470k 1/10W 470k 1/10W 470k 1/10W 8.2k 1/10W 470k 1/10W 470k 1/10W 470k 1/10W 5.6k 1/10W 470k 1/10W 470k 1/10W 470k 1/10W 5.6k 1/10W 150k 1/10W 33k 1/10W 56k 1/10W 10k 1/10W 27 1/10W 22k 1/10W 100k 1/10W 82 1/8W 10 1/10W 9.1k 1/2W 9.1k 1/2W 47k 1/10W 5.1k 1/10W 1k 1/10W 68 1/10W 10 1/10W 100 1/4W 10 1/4W 10k 1/10W 0.22 1/2W 68k 2W 1k 1/10W 220 1/10W 5.1k 1/10W 3.3k 1/10W 3.3k 1/10W 100 1/10W 3.3k 1/2W 9.1k 1/2W 9.1k 1/2W 1 1W 2.2k 1/2W 2.2k 1/10W 1.5k 1/10W 9.1k 1/2W 9.1k 1/2W Chip Chip Chip Chip Metal Oxide Cement Cement Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Metal Oxide Chip Chip Chip Chip Chip Chip Chip Chip Chip Metal Oxide Chip Chip Chip Chip Chip AB AB AB AC AC AH AF AD AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AC AB AB AG AD AB AB AB AB AB AB AD AB AB AC AD AB AB AB AB MISCELLANEOUS PARTS TF701 9FJ0E03010060 9FJ0G10001750 9FJ0i10007550 9FJ0i10007570 9FJ0O00002510 9FJ0O00002520 173 J J J J J J Fuse P125A Connector (PA) B2P3-VH Harness (PL) Harness (E) Heat Sink Heat Sink AG AE AN BB AK AP XG-C40XU/XE Ref. No. ★ Part No. Description Code CPCi-0047CE15/16 PC I/F UNIT INTEGRATED CIRCUITS IC8001 IC8003 IC8006 IC8007 IC8019 IC8020 IC8022 IC8024 IC8025 IC8027 IC8028 IC8029 IC8035 IC8038 IC8039 IC8046 IC8048 IC8051 IC8052 IC8053 IC8056 IC8600 IC8601 IC8603 IC8604 IC8606 IC8607 IC8608 IC8609 IC8610 IC8611 RH-iX3270CEZZ 9DK001-11020 9DK001-12055 9DK001-15061 9DK001-15060 RH-iX3460CEZZQ 9DK001-12086 9DK001-15053 RH-iX3249CEN1 RH-iXA152WJZZQ 9DK001-11027 RH-iX3250CEZZ 9DK001-11021 9DK001-11021 9DK001-11021 9DK001-11021 RH-iX3293CEZZ 9DK001-15091 9DK001-12055 9DK001-12057 9DK001-12058 9DK001-12068 9DK001-20026 9DK001-15038 9DK001-15112 9DK001-15103 9DK001-12070 9DK001-12055 RH-iX3399CEN1Q 9DK001-12068 9DK001-15087 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J HD6417709 AT24C128N-10SC-1.8 TC7WH241FU PST600IM PST623XW GMZ2A 74VHCT244AMT TL431CPS MB87J1101 LH28F320BFE MSM51V18165F-60TS-K MB87J1110 NT56V1616A0T-7 NT56V1616A0T-7 NT56V1616A0T-7 NT56V1616A0T-7 MBCG61394-106 CXD2309AQ TC7WH241FU TC74LVX86FT HD74LVC00T SN74F153DB UPA103G PQ05TZ11 PQ033EZ01 CXA3516AR HD74HCT125T TC7WH241FU IX3399CEN1 SN74F153DB NJM2137V BH AS AN AL AP BP AL AL BT BD J IMB3A BW BB BB BB BB BC BB AN AM AK AM BA AR 9DK001-30001 9DK001-30001 9DK001-30001 9DK001-30001 9DK001-30013 9DK001-30018 9DK001-30018 X8001 X8003 X8004 X8005 9DK001-80012 9DK001-80011 9DK001-80013 9DK001-80023 FL8002 FL8003 FL8005 FL8006 FL8021 FL8022 FL8023 FL8026 FL8027 FL8028 FL8032 FL8034 FL8037 FL8039 FL8041 FL8048 FL8049 FL8051 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 J J J J J J J 1SS193 1SS193 1SS193 1SS193 1SS362 1SS187 1SS187 BR AL AN BM AM AS AE AC AC AC AC AD AD AD PACKAGED CIRCUITS J J J J Crystal, 6MHz Crystal, 1.8432MHz Crystal, 22.165MHz Crystal, 18.75MHz AN AS AN AR FILTERS J J J J J J J J J J J J J J J J J J Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B FL8053 FL8054 FL8056 FL8057 FL8058 FL8600 FL8601 FL8602 FL8603 FL8604 FL8606 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 9DK001-82026 L8600 L8601 L8602 L8603 L8604 9DK001-81052 9DK001-81052 9DK001-81052 9DK001-81052 9DK001-81050 C8001 C8002 C8006 C8009 C8012 C8013 C8019 C8020 C8021 C8022 C8026 C8028 C8029 C8030 C8031 C8035 C8039 C8042 C8043 C8052 C8053 C8170 C8176 C8177 C8178 C8181 C8182 C8185 C8190 C8191 C8192 C8196 C8198 C8207 C8211 C8213 C8216 C8217 C8220 C8223 C8225 C8228 C8230 C8231 C8233 C8247 C8250 C8252 C8255 C8257 C8259 C8265 C8266 C8268 C8273 9DK001-42094 9DK001-42094 9DK001-42096 9DK001-42096 9DK001-42103 9DK001-42103 9DK001-42104 9DK001-42104 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42105 9DK001-42094 9DK001-42096 9DK001-42094 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42103 9DK001-42096 9DK001-42103 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-40080 9DK001-40092 9DK001-40080 9DK001-42103 9DK001-42103 9DK001-42096 9DK001-42096 9DK001-42096 J J J J J J J J J J J Description Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B Filter, STS104B Code AG AG AG AG AG AG AG AG AG AG AG J J J J J Coil, 3.3µH Coil, 3.3µH Coil, 3.3µH Coil, 3.3µH Coil, 68µH AG AG AG AG AG CAPACITORS DIODES D8001 D8002 D8003 D8004 D8600 D8601 D8602 ★ Part No. COILS TRANSISTOR Q8012 9DK001-20025 Ref. No. AG AG AG AG AG AG AG AG AG AG AG AG AG AG AG AG AG AG 174 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 0.1 0.1 0.01 0.01 15p 15p 470p 470p 0.01 0.01 0.01 0.01 0.01 0.047 0.1 0.01 0.1 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 15p 0.01 15p 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 100 220 100 15p 15p 0.01 0.01 0.01 25V 25V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 25V 50V 25V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 6.3V 4V 6.3V 50V 50V 50V 50V 50V Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AF AF AF AC AC AC AC AC XG-C40XU/XE Ref. No. Part No. ★ Description Code CPCi-0047CE15/16 PC I/F UNIT (Continued) C8281 C8283 C8284 C8285 C8297 C8301 C8305 C8309 C8317 C8325 C8328 C8329 C8330 C8332 C8336 C8340 C8341 C8342 C8343 C8344 C8345 C8349 C8355 C8361 C8366 C8367 C8368 C8369 C8370 C8371 C8372 C8373 C8374 C8375 C8376 C8378 C8379 C8425 C8432 C8460 C8470 C8471 C8472 C8600 C8602 C8603 C8604 C8605 C8606 C8607 C8608 C8609 C8610 C8611 C8612 C8613 C8614 C8615 C8616 C8617 C8618 C8619 C8620 C8621 C8623 C8624 C8625 C8626 C8627 C8628 C8630 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42094 9DK001-42094 9DK001-42111 9DK001-42094 9DK001-40077 9DK001-42094 9DK001-42096 9DK001-42101 9DK001-40089 9DK001-40080 9DK001-40092 9DK001-40090 9DK001-40080 9DK001-40080 9DK001-40080 9DK001-40080 9DK001-40090 9DK001-40080 9DK001-40092 9DK001-40080 9DK001-40080 9DK001-40080 9DK001-42096 9DK001-42103 9DK001-42094 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-40089 9DK001-42113 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42108 9DK001-42108 9DK001-40079 9DK001-42096 9DK001-40079 9DK001-42096 9DK001-40079 9DK001-42096 9DK001-40079 9DK001-42096 9DK001-43018 9DK001-42094 9DK001-40079 9DK001-42096 9DK001-43018 9DK001-42094 9DK001-43018 9DK001-42094 9DK001-42094 9DK001-40079 9DK001-42094 9DK001-42096 9DK001-42096 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.1 0.1 1 0.1 10 0.1 0.01 220p 47 100 220 47 100 100 100 100 47 100 220 100 100 100 0.01 15p 0.1 0.01 0.01 0.01 47 4.7 0.1 0.1 0.1 5p 5p 47 0.01 47 0.01 47 0.01 47 0.01 10 0.1 47 0.01 10 0.1 10 0.1 0.1 47 0.1 0.01 0.01 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 25V 25V 10V 25V 16V 25V 50V 50V 6.3V 6.3V 4V 4V 6.3V 6.3V 6.3V 6.3V 4V 6.3V 4V 6.3V 6.3V 6.3V 50V 50V 25V 50V 50V 50V 6.3V 10V 25V 25V 25V 50V 50V 16V 50V 16V 50V 16V 50V 16V 50V 16V 25V 16V 50V 16V 25V 16V 25V 25V 16V 25V 50V 50V Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Electrolytic Ceramic Electrolytic Ceramic Electrolytic Ceramic Tantalum Ceramic Electrolytic Ceramic Tantalum Ceramic Tantalum Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AB AC AF AC AC AC AE AF AF AF AF AF AF AF AF AF AF AF AF AF AC AC AC AC AC AC AE AB AC AC AC AB AB AG AC AG AC AG AC AG AC AH AC AG AC AH AC AH AC AC AG AC AC AC Ref. No. ★ Part No. C8631 C8632 C8633 C8634 C8635 C8636 C8637 C8638 C8640 C8641 C8642 C8645 C8646 C8647 C8648 C8649 C8650 C8651 C8652 C8653 C8654 C8656 C8657 C8662 C8663 C8664 C8672 C8674 C8677 C8678 C8679 C8684 C8685 C8692 C8694 C8695 C8698 C8701 C8702 C8703 C8704 C8705 C8707 C8708 C8720 C8721 C8722 C8723 C8724 C8725 C8729 9DK001-42094 9DK001-42125 9DK001-42111 9DK001-42124 9DK001-42099 9DK001-42099 9DK001-42111 9DK001-42094 9DK001-42111 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42096 9DK001-40079 9DK001-42094 9DK001-42094 9DK001-42096 9DK001-42094 9DK001-42111 9DK001-42111 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42094 9DK001-42096 9DK001-42096 9DK001-42129 9DK001-40090 9DK001-42096 9DK001-40089 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-42096 9DK001-40091 9DK001-43018 9DK001-43018 9DK001-43018 9DK001-42094 9DK001-42094 9DK001-42099 9DK001-42116 9DK001-42116 9DK001-42116 9DK001-42116 9DK001-42116 9DK001-42116 9DK001-42111 FL8001 FL8024 FL8025 FL8033 FL8038 FL8043 FL8044 FL8045 FL8605 R8001 R8002 R8003 R8004 R8005 R8006 R8007 R8009 R8010 R8011 R8012 R8013 R8014 9DK001-50110 9DK001-50110 9DK001-50110 9DK001-50110 9DK001-50110 9DK001-50110 9DK001-50110 9DK001-50110 9DK001-50110 9DK001-50165 9DK001-50165 9DK001-50165 9DK001-50165 9DK001-50163 9DK001-51030 9DK001-50209 9DK001-50204 9DK001-51030 9DK001-51030 9DK001-50207 9DK001-50207 9DK001-51030 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 0.1 0.068 1 680p 100p 100p 1 0.1 1 0.1 0.1 0.1 0.1 0.01 47 0.1 0.1 0.01 0.1 1 1 0.1 0.1 0.1 0.1 0.1 0.01 0.01 0.01 47 0.01 47 0.01 0.01 0.01 0.01 0.01 100 10 10 10 0.1 0.1 100p 10p 10p 10p 10p 10p 10p 1 25V 16V 10V 25V 50V 50V 10V 25V 10V 25V 25V 25V 25V 50V 16V 25V 25V 50V 25V 10V 10V 25V 25V 25V 25V 25V 50V 50V 16V 4V 50V 6.3V 50V 50V 50V 50V 50V 4V 16V 16V 16V 25V 25V 50V 50V 50V 50V 50V 50V 50V 10V Code Ceramic Film Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Film Electrolytic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Tantalum Tantalum Tantalum Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic AC AM AB AC AC AC AB AC AB AC AC AC AC AC AG AC AC AC AC AB AB AC AC AC AC AC AC AC AL AF AC AE AC AC AC AC AC AF AH AH AH AC AC AC AC AC AC AC AC AC AB Chip2125 Chip2125 Chip2125 Chip2125 Chip2125 Chip2125 Chip2125 Chip2125 Chip2125 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Resistor Array Chip1608 Chip1608 Resistor Array Resistor Array Chip1608 Chip1608 Resistor Array AB AB AB AB AB AB AB AB AB AA AA AA AA AA AD AA AA AD AD AA AA AD RESISTORS 175 J J J J J J J J J J J J J J J J J J J J J J 0 0 0 0 0 0 0 0 0 100 100 100 100 68 10k 27k 150 10k 10k 6.8k 6.8k 10k 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W XG-C40XU/XE Ref. No. Part No. ★ Description Code Ref. No. AD AB AB AD AA AA AA AA AD AD AD AD AA AD AD AD AD AD AD AD AD AD AA AA AA AA AA AA AD AD AD AD AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AD AD AA AA AA AA AA AA AA AD AA AB AA R8219 R8220 R8221 R8222 R8223 R8224 R8227 R8228 R8229 R8230 R8231 R8232 R8233 R8239 R8240 R8246 R8251 R8252 R8253 R8254 R8255 R8257 R8264 R8267 R8272 R8276 R8278 R8280 R8281 R8282 R8289 R8290 R8295 R8297 R8298 R8299 R8300 R8301 R8302 R8304 R8305 R8307 R8309 R8316 R8317 R8318 R8319 R8321 R8322 R8323 R8325 R8326 R8327 R8328 R8329 R8330 R8339 R8340 R8341 R8342 R8343 R8344 R8345 R8348 R8353 R8362 R8363 R8364 R8365 R8366 R8367 R8368 R8369 R8370 R8447 CPCi-0047CE15/16 PC I/F UNIT (Continued) R8015 R8016 R8018 R8019 R8022 R8023 R8027 R8028 R8033 R8034 R8035 R8036 R8040 R8043 R8044 R8050 R8051 R8057 R8058 R8061 R8065 R8066 R8071 R8072 R8097 R8100 R8104 R8105 R8107 R8114 R8116 R8117 R8155 R8156 R8157 R8158 R8159 R8160 R8162 R8164 R8167 R8168 R8169 R8170 R8172 R8176 R8180 R8181 R8182 R8183 R8185 R8186 R8187 R8191 R8193 R8194 R8195 R8197 R8202 R8203 R8204 R8205 R8206 R8207 R8209 R8210 R8211 R8215 R8216 R8217 R8218 9DK001-51030 9DK001-50222 9DK001-50199 9DK001-51030 9DK001-50185 9DK001-50185 9DK001-50209 9DK001-50183 9DK001-51030 9DK001-51030 9DK001-51030 9DK001-51030 9DK001-50163 9DK001-51030 9DK001-51030 9DK001-51030 9DK001-51030 9DK001-51030 9DK001-51030 9DK001-51030 9DK001-51030 9DK001-51030 9DK001-50159 9DK001-50159 9DK001-50162 9DK001-50162 9DK001-50162 9DK001-50162 9DK001-51030 9DK001-51030 9DK001-51030 9DK001-51030 9DK001-50150 9DK001-50150 9DK001-50167 9DK001-50163 9DK001-50167 9DK001-50163 9DK001-50163 9DK001-50150 9DK001-50159 9DK001-50159 9DK001-50159 9DK001-50159 9DK001-50201 9DK001-50150 9DK001-50159 9DK001-50159 9DK001-50159 9DK001-50159 9DK001-50165 9DK001-50204 9DK001-50203 9DK001-50159 9DK001-50159 9DK001-50159 9DK001-50159 9DK001-50190 9DK001-51030 9DK001-51030 9DK001-50159 9DK001-50159 9DK001-50159 9DK001-50185 9DK001-50185 9DK001-50173 9DK001-50205 9DK001-51030 9DK001-50150 9DK001-50149 9DK001-50164 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 10k 1/16W 1.3k 1/16W 2.15k1/16W 10k 1/16W 10k 1/16W 10k 1/16W 27k 1/16W 4.7k 1/16W 10k 1/16W 10k 1/16W 10k 1/16W 10k 1/16W 68 1/16W 10k 1/16W 10k 1/16W 10k 1/16W 10k 1/16W 10k 1/16W 10k 1/16W 10k 1/16W 10k 1/16W 10k 1/16W 22 1/16W 22 1/16W 56 1/16W 56 1/16W 56 1/16W 56 1/16W 10k 1/16W 10k 1/16W 10k 1/16W 10k 1/16W 10 1/16W 10 1/16W 180 1/16W 68 1/16W 180 1/16W 68 1/16W 68 1/16W 10 1/16W 22 1/16W 22 1/16W 22 1/16W 22 1/16W 15 1/16W 10 1/16W 22 1/16W 22 1/16W 22 1/16W 22 1/16W 100 1/16W 150 1/16W 62 1/16W 22 1/16W 22 1/16W 22 1/16W 22 1/16W 1M 1/16W 10k 1/16W 10k 1/16W 22 1/16W 22 1/16W 22 1/16W 10k 1/16W 10k 1/16W 470 1/16W 1.8k 1/16W 10k 1/16W 10 1/16W 0 1/16W 82 1/16W Resistor Array Chip1608 Chip1608 Resistor Array Chip1608 Chip1608 Chip1608 Chip1608 Resistor Array Resistor Array Resistor Array Resistor Array Chip1608 Resistor Array Resistor Array Resistor Array Resistor Array Resistor Array Resistor Array Resistor Array Resistor Array Resistor Array Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Resistor Array Resistor Array Resistor Array Resistor Array Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Resistor Array Resistor Array Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Resistor Array Chip1608 Chip1608 Chip1608 176 Part No. 9DK001-50165 9DK001-50185 9DK001-51030 9DK001-51030 9DK001-50185 9DK001-50185 9DK001-50190 9DK001-50150 9DK001-50150 9DK001-50150 9DK001-50165 9DK001-50203 9DK001-50204 9DK001-50169 9DK001-50185 9DK001-50185 9DK001-50159 9DK001-50159 9DK001-50159 9DK001-50159 9DK001-50159 9DK001-50185 9DK001-50162 9DK001-50162 9DK001-50263 9DK001-50155 9DK001-50162 9DK001-50165 9DK001-50222 9DK001-50165 9DK001-50207 9DK001-50165 9DK001-50185 9DK001-50162 9DK001-51030 9DK001-50162 9DK001-50185 9DK001-50185 9DK001-50264 9DK001-50185 9DK001-50185 9DK001-50162 9DK001-50162 9DK001-50185 9DK001-50185 9DK001-50185 9DK001-50169 9DK001-50173 9DK001-50205 9DK001-50150 9DK001-50150 9DK001-50150 9DK001-50150 9DK001-50150 9DK001-50162 9DK001-50165 9DK001-50185 9DK001-50185 9DK001-50150 9DK001-50150 9DK001-50159 9DK001-50185 9DK001-50185 9DK001-50149 9DK001-50149 9DK001-50162 9DK001-50162 9DK001-50162 9DK001-50162 9DK001-50162 9DK001-50162 9DK001-50162 9DK001-50162 9DK001-50162 9DK001-50150 ★ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 100 10k 10k 10k 10k 10k 1M 10 10 10 100 62 150 220 10k 10k 22 22 22 22 22 10k 56 56 1k 3k 56 100 1.3k 100 6.8k 100 10k 56 10k 56 10k 10k 680 10k 10k 56 56 10k 10k 10k 220 470 1.8k 10 10 10 10 10 56 100 10k 10k 10 10 22 10k 10k 0 0 56 56 56 56 56 56 56 56 56 10 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/4W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W Chip1608 Chip1608 Resistor Array Resistor Array Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip3216 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Resistor Array Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Code AA AA AD AD AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AA AA AB AA AA AA AA AA AD AA AA AA AD AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AA AA AA AA AA AA AA AA AA AA XG-C40XU/XE Ref. No. Part No. ★ Description Code J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 10 10k 0 0 0 0 0 0 0 10k 0 360 56 100 68 10k 47 47 100 820 820 150 150 820 820 47 47 22 62 820 22 62 820 820 22 62 3k 0 3k 33k 33k 10 10 0 10k 22 22 22 22 0 0 10k 75 20k 10 10k 13 13 13 22 820 1k 1k 0 0 0 10k 100 33 33 33 1/16W 1/16W 1/10W 1/10W 1/10W 1/10W 1/16W 1/16W 1/16W 1/16W 1/10W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/4W 1/4W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/10W 1/10W 1/10W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/10W 1/16W 1/16W 1/16W 1/16W 1/16W Chip1608 Chip1608 Chip2125 Chip2125 Chip2125 Chip2125 Chip1608 Chip1608 Chip1608 Chip1608 Chip2125 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip3216 Chip3216 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip2125 Chip2125 Chip2125 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 Chip2125 Chip1608 Chip1608 Chip1608 Chip1608 Chip1608 ★ J 0 Description 1/16W Chip1608 Code AB SWITCH PC I/F UNIT (Continued) 9DK001-50150 9DK001-50185 9DK001-50110 9DK001-50110 9DK001-50110 9DK001-50110 9DK001-50149 9DK001-50149 9DK001-50149 9DK001-50185 9DK001-50110 9DK001-50216 9DK001-50162 9DK001-50165 9DK001-50163 9DK001-50185 9DK001-50161 9DK001-50161 9DK001-50165 9DK001-50176 9DK001-50176 9DK001-50204 9DK001-50204 9DK001-50176 9DK001-50176 9DK001-50251 9DK001-50251 9DK001-50159 9DK001-50203 9DK001-50176 9DK001-50159 9DK001-50203 9DK001-50176 9DK001-50176 9DK001-50159 9DK001-50203 9DK001-50155 9DK001-50149 9DK001-50155 9DK001-50210 9DK001-50210 9DK001-50150 9DK001-50150 9DK001-50149 9DK001-50185 9DK001-50159 9DK001-50159 9DK001-50159 9DK001-50159 9DK001-50149 9DK001-50149 9DK001-50185 9DK001-50257 9DK001-50218 9DK001-50150 9DK001-50185 9DK001-50266 9DK001-50266 9DK001-50266 9DK001-50159 9DK001-50176 9DK001-50177 9DK001-50177 9DK001-50149 9DK001-50149 9DK001-50110 9DK001-50185 9DK001-50165 9DK001-50267 9DK001-50267 9DK001-50267 Part No. R8709 9DK001-50149 CPCi-0047CE15/16 R8448 R8456 R8465 R8466 R8471 R8472 R8481 R8482 R8489 R8600 R8601 R8603 R8604 R8605 R8606 R8607 R8608 R8609 R8610 R8611 R8612 R8613 R8614 R8615 R8616 R8618 R8619 R8620 R8621 R8622 R8623 R8624 R8625 R8626 R8627 R8628 R8632 R8634 R8635 R8640 R8641 R8642 R8643 R8644 R8645 R8648 R8649 R8650 R8651 R8654 R8655 R8672 R8673 R8674 R8675 R8680 R8683 R8684 R8685 R8687 R8688 R8690 R8691 R8695 R8697 R8699 R8703 R8704 R8705 R8706 R8707 Ref. No. S8001 9DK001-70012 AA AA AB AB AB AB AB AB AB AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AA AA AA AA AA AA AA AA AA AB AB AB AA AA AA AA AB AA AA AA AA AA AB AB AA AA AA AA AA AA AA AA AA AA AA AA AB AB AB AA AA AD AD AD J Switch SSSS812-B-2B AL MISCELLANEOUS PARTS FB8004 9DK001-81056 P8404 P8405 P8502 TP8004 TP8005 TP8006 TP8007 TP8022 TP8023 177 9DK001-60038 9DK001-60038 9DK001-60038 9DK001-84014 9DK001-84014 9DK001-84014 9DK001-84014 9DK001-84014 9DK001-84014 J Chip Tewite Beads BLM11A102S J Connector, 60-pin J Connector, 60-pin J Connector, 60-pin J Lug, Test Point J Lug, Test Point J Lug, Test Point J Lug, Test Point J Lug, Test Point J Lug, Test Point AR AR AR AE AE AE AE AE AE XG-C40XU/XE Ref. No. Part No. ★ Description Code CABINET AND MECHANICAL PARTS 1 1-1 Not Available DBDYT1185CEK2 1-1 DBDYT1185CEK4 1-1-1 1-1-2 1-1-3 1-1-4 1-1-5 1-2 1-3 1-4 1-5 1-6 Not Available Not Available Not Available Not Available Not Available QSW-Z0526CEZZ XEBSD30P12000 GCOVA1771CESA GCOVA1776CEKA PMLT-0348CEZZ 2 2-1 Not Available DBDYR1092CEK2 2-1 DBDYR1092CEK4 2-1-1 2-1-2 2-1-3 2-2 – Top Cabinet Ass’y J Top Cabinet Ass’y (XG-C40XU) J Top Cabinet Ass’y (XG-C40XE) – Top Cabinet – Holder – Holder, x2 – Lens Caution Label – Tefron Tape J Operation Key Unit J Screw, x2 J R/C Cover, Front J Lens DEC Cover J Molt, x2 — AX — AS Not Available Not Available Not Available GCOVA1779CESA 3 3-1 3-1-1 3-1-1-1 3-1-1-2 3-1-1-3 3-1-1-4 3-1-2 3-1-3 3-1-4 3-2 Not Available Not Available DDORU1017CEK3 Not Available Not Available Not Available Not Available LX-BZ1009CEFN XRESJ30-06000 MSPRC0202CEFW DBDYU1140CEK1 – – J – – – – J J J J — — AU — — — — AE AA AB BB 3-2 DBDYU1141CEK1 J 3-2-1 3-2-2 3-2-3 3-2-4 3-2-5 3-2-6 3-2-7 3-2-8 3-2-9 3-2-10 3-2-11 3-2-12 3-2-13 3-2-14 3-3 3-5 3-6 3-7 3-8 3-9 3-10 3-11 3-11-1 3-11-2 3-12 3-16 3-17 3-19 3-20 3-21 3-22 Not Available Not Available Not Available Not Available Not Available Not Available Not Available Not Available Not Available Not Available Not Available Not Available Not Available Not Available JHNDA1038CESB GLEGP9119CEKB GCOVA1836CEKA XEBSD30P12000 QCNW-5062CEZZ VSP0082PBR34A QCNW-5761CEZZ DCOVA1775CEK4 Not Available Not Available PFiLD0075CEZZ LX-HZ3066CEFD XEBSD26P14000 RH-HZ0051CEZZ GLEGP1031CESA PSPAH0648CE00 LX-NZ3095CEFD – – – – – – – – – – – – – – J J J J J J J J – – J J J J J J J — — — AE BB — — — — — — — — — — — — — — AV AU AK AA AE AP AG AQ — — AD AB AA AN AG AB AA 178 Description 6 Refer to Optics Mechanism Parts 7 8 LHLDZ2093CEKZ RBiM-0001CEZZ 9 10 12 13 14 15 16 17 18 20 21 22 23 25 26 27 28 29 33 34 35 36 41 42 43 44 45 48 56 57 58 59 60 61 62 63 AS ★ XEBSD30P10000 PSPAT0013CEZZ 8 — — — — — BA AA AE AP AE Part No. 3-23 3-25 AX – Rear Cabinet Ass’y J Rear Cabinet Ass’y (XG-C40XU) J Rear Cabinet Ass’y (XG-C40XE) – Rear Cabinet – Terminal Indication Sheet – Hot Cavtion Label J R/C Cover, Rear Bottom Cabinet Ass’y Lamp Cage Cover Ass’y Lamp Cage Cover Ass’y Lamp Cage Cover Caution Label Panching Duct Screw E-Ring Spring Bottom Cabinet Ass’y (XG-C40XU) Bottom Cabinet Ass’y (XG-C40XE) Bottom Cabinet Model Label Interlock Cavtion Lavel FCC Index Punching Plate Angle Shielding Holder Nut Nut, x4 Handle Spacer, x2 Tefron Tape, x4 PBS Inhaust Filter Ballast Bottom Filter Lens Bottom Filter Handle Front Adjuster Front Cover Screw, x2 Speaker Lead Wire Speaker Leaf Switch Intake Cover Ass’y Intake Cover Intake Cover Punching Intake Air Filter Screw Screw, x2 Temp. Sensor Back Adjuster Adjuster Spacer M5 Nut Ref. No. J Screw, x1 J Teflon Tape J Bimetal Holder J Bimetal (XG-C40XU) RBiM-0104CEZZ J Bimetal (XG-C40XE) PCOVW9007CEKZ J Bimetal Cover GCOVH1307CESB J Lens Cap Refer to Power/Ballast Unit Parts Not Available – Output Unit Not Available – PC I/F Unit Not Available – PC Terminal Unit Not Available – Video Unit Not Available – Signal Unit XBPSD40P08JS0 J Screw, x1 NSFTZ0144CEFW J Spacer, x4 LANGT3295CEFW J Angle (L) LANGT3265CEFW J Angle (R) NFANR0104CE00 J Fan LANGQ5709CEFW J Angle XBSSD26P14000 J Screw, x2 NSFTZ0140CEFW J Shaft, x7 Not Available – Sound Out/Regulator Unit Not Available – Inlet Unit XEBSD30P10000 J Screw, x4 XTBSF30P12000 J Screw, x4 XBPSF30P10000 J Screw, x4 XBPSD30P06R00 J Screw, x12 XEBSD30P06000 J Screw, x2 XBPSD26P04000 J Screw, x13 XTASD30P16000 J Screw, x9 XBBSF26P05000 J Screw, x1 XEBSF30P08000 J Screw, x1 QCNW-4929CEZZ J Bimetal Wire LX-HZ3106CEFD J Screw, x2 XEBSD30P08000 J Screw LX-NZ3166CEFD J Nut QCNW-5224CEZZ J AC Power Switch PSPAF0032CEFW J Spacer(L) PSPAF0033CEFW J Spacer(R) QEARPA002WJFW J PC Earth XBPSD26P04000 J Screw,x2 Code AA AC AK AN AN AF AV — — — — — AA AD AK AH AW AE AA AC — — AA AA AA AB AA AA AA AA AA AG AB AA AA AW AF AF AE AA A 1 2 58 3 179 P 9 4 F SP 5 25 SO 33 3-6 3-19 3-2-14 3-7 3-23 F 3-2-5 3-17 3-5 3-25 3-10 3-2-1 3-2-3 3-2-9 3-2-9 3-2-13 3-2-12 3-2-2 3-2-11 L 6 3-2 3-2-4 3-2-7 3-22 C 3-11-2 3-12 3-2-8 3-11 3-20 3-21 3-2-6 3-2-11 A 3-2-10 59 3-11-1 3-3 3-1 3-1-2 3-1-4 3-1-3 43 E 3-1-1 3-1-1-1 3-1-1-3 3-1-1-4 3-1-1-2 29 57 3 ★ 28 EB 48 45 C B 3-8 3-9 3-16 1-1 Part No. EA D 8 33 6 33 1-1-5 2-1 2-1-1 2-1-3 H 41 7 J A 1-3 1-6 F H 43 12 1-5 1-1-4 2-2 2-1-2 Ref. No. AR D EA E 1-6 1-1-1 1-1-3 35 Code SH 20 60 18 56 1-4 1-1-2 1-1-3 Description 10 H G B 36 33 42 27 36 42 2 34 ★ 13 20 20 14 22 16 1 CABINET AND MECHANICAL PARTS/ GEHÄUSE UND MECHANISCHE BAUTEILE Part No. 61 44 G 21 17 D 60 23 1-2 Ref. No. 36 I 62 26 C 36 G 36 63 42 P AR I E SH 15 XG-C40XU/XE Description Code XG-C40XU/XE Ref. No. Part No. ★ Description Code 6-67 6-68 6-69 6-70 6-71 6-72 6-73 6-74 6-75 6-77 6-78 6-79 6-80 6-81 6-82 6-83 6-84 6-85 6-86 6-87 6-88 6-89 6-90 6-91 OPTICS MECHANISM PARTS 6 6-1 6-2 6-3 6-4 6-5 6-6 6-7 6-8 6-9 6-10 6-11 6-12 6-13 6-14 å 6-15 å 6-15-1 6-15-2 6-15-2-1 6-15-2-2 6-15-2-3 6-15-3 6-15-4 6-15-5 6-15-6 6-15-7 6-15-8 6-15-9 6-15-10 6-15-11 6-15-12 6-15-13 6-16 6-17 6-18 6-19 6-20 6-21 6-22 6-23 6-24 6-25 6-26 6-27 6-29 6-30 6-31 6-32 6-34 6-35 6-36 6-37 6-38 6-39 6-40 6-42 6-43 6-45 6-46 6-47 6-48 6-49 6-51 6-52 6-53 6-54 6-55 6-57 6-63 6-66 CCHSK0075CE71 LCHSK0094CEFW LCHSK0075CEFW CANGK0675CE02 LANGK0747CEFW LANGK0677CEFW LANGG1192CEFW PSLDP3075CEFW J J J J J J J J PDUC-0121CEKZ NFANR0109CE00 CDUC-0122CE01 LHLDZ3067CEFW PGiDH0039CEKZ NFANR0122CE00 MSPRP1198CEFW BQC-XGC40XU/1 RLMPF0075CEZZ CCASZ0108CE01 PCASZ0108CEKZ LHLDZ3058CEFW PCOVZ0103CEFW LX-HZ3105CEFD LANGK0750CEFW MSPRP0215CEFW MSPRP0218CEFW XBSSD30P06000 XBPSD20P04000 PSLDP3062CEFW XEPSD30P06000 TLABZ0795CEZZ XBPSD30P08JS0 TLABZ0758CEZZ LANGK0680CEFW PLNS-0148CEZZ PLNS-0242CEZZ PLNS-0241CEZZ PLNS-0151CEZZ PLNS-0220CEZZ PLNS-0153CEZZ PFiLW0294CEZZ PMiR-0216CEZZ PMiR-0219CEZZ PMiR-0271CEZZ PLNS-0219CEZZ PMiR-0266CEZZ PMiR-0267CEZZ PLNS-0221CEZZ MSPRP1205CEFW LHLDZ3059CEFW LHLDZ3060CEFW CLNS-0172CE01 RLCDP0141CEZZ RLCDP0142CEZZ RLCDP0143CEZZ PMiR-0265CEZZ RH-HZ0048CEZZ LANGU9029CEFW XAPSF20P05000 LX-BZ3402CEZZ XASSF26P06000 XBPSD26P04000 LX-BZ3370CEFD XBBSD26P08000 XBPSD30P08JS0 XJPSD30P08000 XBBSD30P08000 XEBSD30P10000 XEBSD40P20000 LANGH0144CEFW XBPSD26P06JS0 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Optics Mecha. Ass’y Optics Mecha. Base Optics Mecha. Cover R/B Convergence Unit, x2 G Adjusting Plate Slide Plate, x3 Guide Plate Light Shielding Plate (LCD Module Unit, Green) Duct ,Side Cooling Fan(Exhaust) Duct ,Top Holder, for Prism Flap Cooling Fan(Intake) Mirror Fitting Spring, x27 Lamp/Cage Module Unit Lamp/Mirror Ass’y Lamp Case Ass’y Lamp Case Handle Lamp Case Punting Ney Screw Lamp Angle Spring (A) Spring (B) Screw, x2 (A) Screw, x2 (B) Lamp Shield Screw Label Screw, x3 Label Duct Holding Plate CL1 CL3 (for Green) CL2 (for Red) RL1 (Incoming-Light) RL2 RL3 (Outgoing-Light) Polarizer B Mirror-M1 Mirror-M4/M6 ,x2 Mirror-M5 Flyeye Lens1 Mirror-M2 Mirror-M3 Flyeye Lens2, PBS Flyeye Fitting Spring,x2 M1 Adjust Lever Ass’y M Adjust Lever Ass’y, x2 Projection Lens LCD Module Unit, Red LCD Module Unit, Green LCD Module Unit, Blue Cross Prism (with Base) Temp. Sensor Angle, for Temp. Sensor Screw M2-5, x2 Screw 2P-5, x13 Screw M2.6-6, x12 Screw M2.6-4 Screw 2.6P-6, x4 Screw 2.6P-8, x6 Screw M3-8, x3 Screw M3-8 Screw 3P-8, x4 Screw M3-10, x2 Screw M4-20, x2 Light Shielding Plate Screw 2.6P-6, x6 Ref. No. FT BM BL AY AG AD AR AH AR BA AX BC AF AX AD CQ CL AW AP AE AG AB AK AF AE AA AA AG AA AC AA AD AE BB BC BC AU AY AU BG BA AS AL BP BC AZ CA AD AK AH CG CT CT CT CB AN AF AA AB AB AA AB AA AA AA AA AA AA AE AA 180 Part No. ★ LANGK0755CEFW LANGK0785CEFW LANGK0751CEFW LANGK0752CEFW LANGK0753CEFW LANGK0756CEFW LHLDZ0112CEKZ LHLDZ0113CEKZ NFANR0125CE00 PFiLW0254CEZZ PFiLW0293CEZZ PSPAZ0373CEZZ PSLDH3073CEFW XBBSD30P10000 PFiLW0297CEZZ PFiLW0295CEZZ QEARP0114CEFW XBBSD26P06000 XBPSD30P10JS0 XBPSD20P04000 XEPSD26P08000 XEPSD30P06000 XiPSF20P02000 PSLDP3078CEFW J J J J J J J J J J J J J J J J J J J J J J J J Description Code Angle, for Emergent Pollarizer B Fan Angle for PBS Fan Angle A Fan Angle B Fan Angle C Fan Angle D RL2-Holder Holder for PBS Fan Cooling Fan (Intake for PBS) UV Filter UV Filter 0.8t Fan Bush, x15 Duct shielding plate Screw, x2 Emergent Polarizer G Emergent Polarizer B Heat Shielding Plate Screw M2.6-6, x3 Screw M3-10, x4 Screw M2-4, x3 Screw M2.6-8, x4 Screw M3-6, x1 Screw M2-2, x3 Flyeye Lens Aperture AK AK AF AE AF AF AF AL AU BA AY AC AE AA BE BH AH AA AA AA AA AA AA AG 1 2 A 6-86 6-11 B 3 181 4 6-57 6-12 6-53 6-75 6-89 6-68 6-90 6-45 6-83 6-85 6-39 6-79 6-79 6-47 6-54 6-19 6-18 6-17 6-26 6-1 6-24 6-29 6-30 6-2 6-14 6-16 6-14 6-49 6-32 6-31 6-23 6-27 6-54 6-25 6-54 6-91 6-35 6-20 6-22 6-25 6-32 6-51 6-66 6-51 6-14 6-51 6-21 6-73 6-80 6-10 6-8 5 6-77 6-78 6-81 6-15-2-1 6-15-4 6-15-5 6-15-7 6-15-2-3 6-15-2 6-15-13 6-52 6-15-9 6-15-12 6-15-2-2 6-15-10 6-72 6-15-3 6-15-6 6-15-8 6-88 6-79 6-79 6-87 6-15-11 6-15-1 6-15 6-84 6-71 6-87 6-9 6-79 6-70 6 ★ 6-74 6-13 6-67 6-7 6-5 6-46 6-3 6-14 6-79 6-88 Part No. ★ Description Code Ref. No. Part No. OPTICS MECHANISM PARTS/ TEILE FÜR OPTIKMECHANISMUS 6-57 6-48 6-40 6-49 6-6 6-5 6-82 6-51 6-35 6-55 6-88 6-87 6-69 Ref. No. 6-86 6-86 6-36 6-63 6-46 6-5 C 6-46 6-47 6-14 6-51 6-14 6-66 6-43 F 6-46 6-3 6-4 6-38 6-34 E 6-42 G 6-37 6-47 6-46 6-46 6-66 6-66 6-49 XG-C40XU/XE Description Code H D 6 XG-C40XU/XE Ref. No. Part No. ★ Description Code POWER/BALLAST UNIT PARTS 12 12-1 12-2 12-3 12-4 12-5 12-6 12-7 12-8 12-9 Not Available 9FJ0N00002020 9FJ0N00002030 9FJ0M41001170 9FJ0A11901620 9FJ0A11901610 9FJ0G20002960 9FJ0G20002690 RDENC0334CEZZ RDENC0333CEZZ – J J J J J J J – J 12-10 12-11 12-12 12-13 12-14 9FJ0S89000080 9FJ0S89000020 9FJ0S08004200 9FJ0K00001220 XBPSD30P04000 J J J J J Power/Ballast Unit Ass'y — Case Base AX Cover AW Fan AZ Insulating Sheet AL Insulating Sheet Spacer AD Spacer AD Power Unit — Ballast Unit CC (The ballast unit is supplied only as an assembly.) Screw AC Screw AB Screw AC Serial Number Label AU Screw AA 182 Ref. No. Part No. ★ Description Code XG-C40XU/XE Part No. ★ DescriptionUNIT Code Ref. No. Part No. POWER/BALLAST PARTS/ TEILE FÜR NETZ-/BALLASTEINHEIT Ref. No. ★ Description Code H 12-2 12-11 12-14 12 12-14 G 12-5 12-14 12-14 F 12-3 12-12 12-10 E 12-8 12-10 12-9 D 12-13 12-4 12-6 C 12-1 12-6 12-7 12-7 B A 1 2 3 4 183 5 6 XG-C40XU/XE Ref. No. Part No. ★ Description Code PFiLD0076CEZZ QACCU5013CEZZ å å RCORF0083CEZZ QACCB5024CENA å QACCV4002CEZZ QCNW-4870CEZZ QCNW-5288CEZZ QCNWG0007CEPZ QCNWG0002CEZZ RRMCG1579CESA RRMCG1584CESA RUNTK0673CEZZ UDSKA0053CEN1 UDSKA0057CEN1 TiNS-7482CEZZ TiNS-7533CEZZ TiNS-7483CEZZ TiNS-7534CEZZ TiNS-7535CEZZ TiNS-7536CEZZ TiNS-7538CEZZ TiNS-7537CEZZ GCOVH1307CESB J Extra Air Filter J AC Cord (XG-C40XU) J Core(XG-C40XU) J AC Cord (XG-C40XE) J AC Cord (XG-C40XE) J Computer Audio Cable J DIN D-Sub RS-232C Cable J USB Mouse Control Cable J Computer RGB Cable J Wireless R/C Unit (XG-C40XU) J Wireless R/C Unit (XG-C40XE) J Remote Mouse Receiver J CD-ROM (XG-C40XU) J CD-ROM (XG-C40XE) J Operation Manual (XG-C40XU) J Operation Manual (XG-C40XE) J Quick Reference (XG-C40XU) J Quick Reference (XG-C40XE) J Quick Reference (XG-C40XE) J Quick Reference (XG-C40XE) J SAPS Operation Manual (XG-C40XU) J SAPS Operation Manual (XG-C40XE) J Lens Cap – Software Caution – Two AA Size Batteries ★ Description Code (NOT REPLACEMENT ITEM) AE AX SPAKC5598CEZZ SPAKC5613CEZZ AL AZ SPAKP0805CEZZ SPAKX2918CEZZ SPAKF0467CEZZ TLABK0001TAZZ AZ – Packing Case (XG-C40XU) – Packing Case (XG-C40XE) – Polystyrene Cover – Buffer Material – Sleeve(Box for Accessories) – Number Card — — — — — — AQ AM AL AW BR BR SERVICE JIGS BM AQ (Use for servicing) AQ 9DASPN-XGNV1U AS 9EQDRiVER-NV1B AY 9EQLNC-XGNV1U or 9EQLNC-XGNV4U QCNW-5058CEZZ AG AG QCNW-4767CEZZ AG AF QCNW-5057CEZZ AM AX QCNW-5688CEZZ AV ACCESSORIES (NOT REPLACEMENT ITEM) TCAUZ3036CEZZ – Part No. PACKING PARTS SUPPLIED ACCESSORIES å Ref. No. — — 184 J Spanna, 3mm BG (Off-set Cam Adjustment) J Screwdriver, (–) BL (Focus Adjustment) J Hexagon Wrench, 2mm BA (Convergence Adjustment) J Extension Cable 28-pin CB Signal(P1501)-Output(SC1501) Signal(P1502)-Output(SC1502) J Extension Cable 30-pin BT Signal (VS)-Video (VS) Signal (TN)-PC Terminal (TN) J Extension Cable 60-pin CD Output (TC1)-PC I/F (TC1) Output (TC2)-PC I/F (TC2) Output (TC3)-PC I/F (TC3) J Extension Cable 30-pin BK LCD Panel-Output XG-C40XU/XE Part No. ★ Description Ref. No. Part No. ★ Description PACKING OF THE SETCode / VERPACKEN DES GERÄTS Ref. No. Sleeve (Box for Accessories) / Hülse (Kasten für Zubehör) Code Wireless R/C Unit / Drahtlose Fernbedienungseinheit Remote Mouse Receiver / Fernbedienungs-Mausempfänger Computer Audio Cable / Computer-Audiokabel Computer RGB Cable / RGB-Computerkabel AC Cord / Netzkabel USB Mouse Control Cable / USB-Maus-Steuerungskabel DIN D-Sub RS-232C Cable / DIN-D-Sub RS-232C-Kabel Two AA Size Batteries / Zwei Batterien der Größe AA Sleeve / Hülse CD-ROM /CD-ROM Extra Air Filter / Ersatz-Luftfilter Operation Manual / Bedienungsanleitung Buffer Material (Front and Back) / Polstermaterial (Vorder-und Rückseite) Polystyrene Cover / Polystyrol-Verpackung Packing Case / Karton Front / Vorder The packing case top is tape-sealed. / Die Oberseite des Verpackungskartons wurde mut Klebestreifen verschlossen. Number Card / Nummerkarte Use 8 staples to fix the packing case.(Bottom Side) / Den Verpackungskarton mit8 Heftklammern (Krampen) Verschließen.(Unterseite) 185 XG-C40XU/XE Ref. No. Part No. ★ Description Code Ref. No. ★ Part No. Description Code COPYRIGHT © 2001 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. D Japan P Japan TQ1223-S Oct. 2001 Printed in Japan In Japan gedruckt SHARP CORPORATION AV Systems Group Quality & Reliability Control Center Yaita, Tochigi 329-2193, Japan SY. KY 186