Download Magnavox 32MD311B Service manual
Transcript
32” LCD TV/DVD chassis FL11.11 SERVICE MANUAL Contents TYPE A LD320SS2 SYLVANIA (Serial No.: DS1) 32MD301B/F7 MAGNAVOX (Serial No.: DS1) 32MD311B/F7 MAGNAVOX (Serial No.: DS1) This service manual contains information of different types of models. Make sure to refer to the section describing your model. © 2011 Funai Electric Co., Ltd. All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded or stored in any storage medium, in any form or for any purpose without the express prior written consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited. Information in this document is subject to change without notice. Funai reserves the right to change the content herein without the obligation to notify any person or organization of such changes. with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the express written consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing contained in this manual should be construed as granting, by implication or otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law. 110427 IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all Funai Equipment. The service procedures recommended by Funai and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended. It is important to note that this service manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It also is important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. Funai could not possibly know, evaluate and advice the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, Funai has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by Funai must first use all precautions thoroughly so that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected. The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a tiny spec of color. This is not to be considered a defect in the LCD screen. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. TABLE OF CONTENTS Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Laser Beam Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Electrical Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 How to Initialize the LCD TV/DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1 Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1 Schematic Diagrams / CBA and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1 System Control Timing Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1 Lead Identifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-1 Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-1 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-1 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-1 SPECIFICATIONS < LCD TV Section > < TUNER / NTSC > ANT. Input ---------------------- 75 Ω Unbal., F type Description Condition Unit Nominal Limit --- MHz ±2.3 ±2.1 TV.ch.4 CA.ch.31 CA.ch.87 dBµ dBµ dBµ 18 18 18 20 20 23 Condition Unit Nominal Limit --- kHz --- ±100 ch.4 ch.10 ch.41 dBm dBm dBm ------- -76/0 -76/0 -76/+4 Description Condition Unit Nominal Limit 1. Native Pixel Resolution Horizontal Vertical pixels pixels 1366 768 ----- --- cd/m2 310 --- Horizontal Vertical ° ° -88 to 88 -88 to 88 ----- Condition Unit Nominal Limit Horizontal Vertical % % 5 5 5±5 5±5 --x y °K 12000 0.272 0.278 --±3% ±3% Horizontal Vertical line line 400 350 ----- 1. AFT Pull-In Range 2. Synchronizing Sens. < TUNER / ATSC > Description 1. Received Freq. Range (-28dBm) 2. ATSC Dynamic Range (min / max) < LCD PANEL > 2. Brightness (w / filter) 3. Viewing Angle < VIDEO > Description 1. Over Scan 2. Color Temperature 3. Resolution (composite video) < AUDIO > All items are measured across 8 Ω load at speaker output terminal with L.P.F. Description 1. Audio Output 10% Distortion (ATSC 0 dBfs) 2. Audio Distortion (NTSC) 3. Audio Freq. Response (NTSC) Condition Unit Nominal Limit Lch/Rch W 10.0/10.0 9.0/9.0 500mW: Lch/Rch % 0.5/0.5 2.0/2.0 -6dB: Lch -6dB: Rch Hz Hz 70 to 10 k 70 to 10 k ----- 1-1 FL11.11SP <DVD Section> < DVD > Description Condition Unit Nominal Limit 1. Horizontal Resolution (TDV-540 TIT.2 CHP.16) --- Line 350 330 2. Audio Distortion (LPCM 48 kHz, W/LPF) (PTD 1-NOR TIT.1 CHP.1) L R % 0.03 0.07 L, 20 Hz R, 20 Hz L, 20 kHz R, 20 kHz dB 0 +4/-5 L R dB 85 75 3. Audio freq. response (LPCM 48 kHz) (PTD 1-NOR TIT.1 CHP.5 -- 10) 4. Audio S/N (LPCM 48 kHz, W/LPF, A-WTD) (PTD 1-NOR TIT.1 CHP.1 -- 2) Note: Nominal specifications represent the design specifications. All units should be able to approximate these. Some will exceed and some may drop slightly below these specifications. Limit specifications represent the absolute worst condition that still might be considered acceptable. In no case should a unit fail to meet limit specifications. 1-2 FL11.11SP LASER BEAM SAFETY PRECAUTIONS This DVD player uses a pickup that emits a laser beam. Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin. The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 11.8 inches (30 cm) away from the pickup lens when the diode is turned on. Do not look directly at the laser beam. CAUTION: Use of controls and adjustments, or doing procedures other than those specified herein, may result in hazardous radiation exposure. Drive Mechanism Assembly Laser Beam Radiation Laser Pickup Turntable Location: Top of LCD Module 2-1 TVDVDN_LBSP(1EM435619)(A1DA1UH).fm IMPORTANT SAFETY PRECAUTIONS Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced. Safety Precautions for LCD TV Circuit d. Leakage Current Hot Check - With the instrument completely reassembled, plug the AC line cord directly into a 120 V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI) C101.1 Leakage Current for Appliances and Underwriters Laboratories (UL) 1410, (50.7). With the instrument AC switch first in the on position and then in the off position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle brackets, metal cabinet, screw heads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5 milli-ampere. Reverse the instrument power cord plug in the outlet and repeat the test. 1. Before returning an instrument to the customer, always make a safety check of the entire instrument, including, but not limited to, the following items: a. Be sure that no built-in protective devices are defective and have been defeated during servicing. (1) Protective shields are provided on this chassis to protect both the technician and the customer. Correctly replace all missing protective shields, including any removed for servicing convenience. (2) When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including but not limited to, nonmetallic control knobs, insulating fishpapers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning. Servicers who defeat safety features or fail to perform safety checks may be liable for any resulting damage. READING SHOULD NOT BE ABOVE 0.5 mA DEVICE BEING TESTED b. Be sure that there are no cabinet openings through which an adult or child might be able to insert their fingers and contact a hazardous voltage. Such openings include, but are not limited to, (1) spacing between the Liquid Crystal Panel and the cabinet mask, (2) excessively wide cabinet ventilation slots, and (3) an improperly fitted and/or incorrectly secured cabinet back cover. LEAKAGE CURRENT TESTER _ + TEST ALL EXPOSED METAL SURFACES ALSO TEST WITH PLUG REVERSED USING AC ADAPTER PLUG AS REQUIRED c. Antenna Cold Check - With the instrument AC plug removed from any AC source, connect an electrical jumper across the two AC plug prongs. Place the instrument AC switch in the on position. Connect one lead of an ohmmeter to the AC plug prongs tied together and touch the other ohmmeter lead in turn to each tuner antenna input exposed terminal screw and, if applicable, to the coaxial connector. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohm, an abnormality exists that must be corrected before the instrument is returned to the customer. Repeat this test with the instrument AC switch in the off position. EARTH GROUND ANY MEASUREMENTS NOT WITHIN THE LIMITS SPECIFIED HEREIN INDICATE A POTENTIAL SHOCK HAZARD THAT MUST BE ELIMINATED BEFORE RETURNING THE INSTRUMENT TO THE CUSTOMER OR BEFORE CONNECTING THE ANTENNA OR ACCESSORIES. 2. Read and comply with all caution and safetyrelated notes on or inside the receiver cabinet, on the receiver chassis, or on the Liquid Crystal Panel. 3-1 LTVN_ISP 7. Product Safety Notice - Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by a # on schematics and in parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire, and/or other hazards. The product's safety is under review continuously and new instructions are issued whenever appropriate. Prior to shipment from the factory, our products are strictly inspected to confirm they comply with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced. 3. Design Alteration Warning - Do not alter or add to the mechanical or electrical design of this TV receiver. Design alterations and additions, including, but not limited to circuit modifications and the addition of items such as auxiliary audio and/or video output connections, might alter the safety characteristics of this receiver and create a hazard to the user. Any design alterations or additions will void the manufacturer's warranty and may make you, the servicer, responsible for personal injury or property damage resulting therefrom. 4. Hot Chassis Warning a. Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord and maybe safety-serviced without an isolation transformer only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC power source. To confirm that the AC power plug is inserted correctly, with an AC voltmeter, measure between the chassis and a known earth ground. If a voltage reading in excess of 1.0 V is obtained, remove and reinsert the AC power plug in the opposite polarity and again measure the voltage potential between the chassis and a known earth ground. b. Some TV receiver chassis normally have 85V AC(RMS) between chassis and earth ground regardless of the AC plug polarity. This chassis can be safety-serviced only with an isolation transformer inserted in the power line between the receiver and the AC power source, for both personnel and test equipment protection. c. Some TV receiver chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulation material that must not be defeated or altered. 5. Observe original lead dress. Take extra care to assure correct lead dress in the following areas: a. near sharp edges, b. near thermally hot parts-be sure that leads and components do not touch thermally hot parts, c. the AC supply, d. high voltage, and, e. antenna wiring. Always inspect in all areas for pinched, out of place, or frayed wiring. Check AC power cord for damage. 6. Components, parts, and/or wiring that appear to have overheated or are otherwise damaged should be replaced with components, parts, or wiring that meet original specifications. Additionally, determine the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard. 3-2 LTVN_ISP Precautions during Servicing A. Parts identified by the # symbol are critical for safety. Replace only with part number specified. B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements. Examples: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc. C. Use specified internal wiring. Note especially: 1) Wires covered with PVC tubing 2) Double insulated wires 3) High voltage leads D. Use specified insulating materials for hazardous live parts. Note especially: 1) Insulation Tape 2) PVC tubing 3) Spacers 4) Insulators for transistors. E. When replacing AC primary side components (transformers, power cord, etc.), wrap ends of wires securely about the terminals before soldering. F. Observe that the wires do not contact heat producing parts (heat sinks, oxide metal film resistors, fusible resistors, etc.) G. Check that replaced wires do not contact sharp edged or pointed parts. H. When a power cord has been replaced, check that 11~13 lb (5~6 kg) of force in any direction will not loosen it. I. Also check areas surrounding repaired locations. J. Use care that foreign objects (screws, solder droplets, etc.) do not remain inside the set. K. When connecting or disconnecting the internal connectors, first, disconnect the AC plug from the AC supply outlet. L. When installing parts or assembling the cabinet parts, be sure to use the proper screws and tighten certainly. 3-3 LTVN_ISP Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards. 1. Clearance Distance When replacing primary circuit components, confirm specified clearance distance (d) and (d') between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1) Chassis or Secondary Conductor Primary Circuit Table 1: Ratings for selected area AC Line Voltage Region Clearance Distance (d), (d’) 110 to 130 V U.S.A. or Canada ≥ 3.2 mm (0.126 inches) d' d Note: This table is unofficial and for reference only. Be sure to confirm the precise values. Fig. 1 2. Leakage Current Test Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below. Exposed Accessible Part Z AC Voltmeter (High Impedance) Measuring Method: (Power ON) Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across both terminals of load Z. See Fig. 2 and following table. B Earth Ground Power Cord Plug Prongs Fig. 2 Table 2: Leakage current ratings for selected areas AC Line Voltage Region Load Z Leakage Current (i) Earth Ground (B) to: 110 to 130 V U.S.A. or Canada 0.15 µF CAP. & 1.5 kΩ RES. Connected in parallel i ≤ 0.5 mA rms Exposed accessible parts Note: This table is unofficial and for reference only. Be sure to confirm the precise values. 3-4 LTVN_ISP STANDARD NOTES FOR SERVICING Circuit Board Indications Pb (Lead) Free Solder 1. The output pin of the 3 pin Regulator ICs is indicated as shown. Pb free mark will be found on PCBs which use Pb free solder. (Refer to figure.) For PCBs with Pb free mark, be sure to use Pb free solder. For PCBs without Pb free mark, use standard solder. Top View Out Bottom View In Input 2. For other ICs, pin 1 and every fifth pin are indicated as shown. 5 Pb free mark Pin 1 How to Remove / Install Flat Pack-IC 1. Removal 10 With Hot-Air Flat Pack-IC Desoldering Machine: 3. The 1st pin of every male connector is indicated as shown. 1. Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1) Pin 1 Instructions for Connectors 1. When you connect or disconnect the FFC (Flexible Foil Connector) cable, be sure to first disconnect the AC cord. 2. FFC (Flexible Foil Connector) cable should be inserted parallel into the connector, not at an angle. Fig. S-1-1 2. Remove the flat pack-IC with tweezers while applying the hot air. FFC Cable 3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) Connector 4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) CBA CAUTION: 1. The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC. * Be careful to avoid a short circuit. 2. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape 4-1 TVDVDN_SN With Soldering Iron: around the flat pack-IC to protect other parts from damage. (Fig. S-1-2) 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3) 3. The flat pack-IC on the CBA is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it. Flat Pack-IC CBA Desoldering Braid Hot-air Flat Pack-IC Desoldering Machine Soldering Iron Fig. S-1-3 Masking Tape Tweezers 2. Lift each lead of the flat pack-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine. (Fig. S-1-4) Flat Pack-IC Fig. S-1-2 Sharp Pin Fine Tip Soldering Iron Fig. S-1-4 3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) 4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) 4-2 TVDVDN_SN With Iron Wire: 2. Installation 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3) 1. Using desoldering braid, remove the solder from the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily. 2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5. 2. The “ I ” mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the pin 1 on the PCB when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.) 3. While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5. 3. Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges. 4. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) Example : 5. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied. Pin 1 of the Flat Pack-IC is indicated by a " " mark. Hot Air Blower or Fig. S-1-7 Presolder Iron Wire Soldering Iron To Solid Mounting Point Fig. S-1-5 Flat Pack-IC CBA CBA Fig. S-1-8 Fine Tip Soldering Iron Flat Pack-IC Tweezers Fig. S-1-6 4-3 TVDVDN_SN Instructions for Handling Semiconductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body. 2. Ground for Workbench Be sure to place a conductive sheet or copper plate with proper grounding (1 MΩ) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing. <Incorrect> CBA <Correct> Grounding Band 1MΩ CBA 1MΩ Conductive Sheet or Copper Plate 4-4 TVDVDN_SN CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart Step/ Loc. No. This flowchart indicates the disassembly steps for the cabinet parts, and the CBA in order to gain access to items to be serviced. When reassembling, follow the steps in reverse order. Bend, route and dress the cables as they were. [9] [1] Stand Assembly [7] Jack CBA [2] Rear Cabinet [10] Speaker [9] Digital Main CBA Unit [3] DVD Holder [11] IR Sensor CBA [4] DVD Mechanism [8] Power Supply CBA [12] Function CBA [5] DVD Main CBA Unit [13] LCD Module Assembly 2. Disassembly Method Part Fig. No. Removal Removal Note --- 8(S-13), Hook, Speaker Holder(L, R) --- IR Sensor CBA D4 D4 2(S-14), CL103C D5 --- Function [12] CBA 3(S-15), D4 LED Lens*2, D5 Function Knob*2, Shield Plate*2 --- LCD [13] Module Assembly D4 (S-16) --- D4 --------------- --- ↓ (3) ↓ (5) [11] [14] Front Cabinet Fig. No. 3(S-11), 8(S-12), Digital Main D3 CN3005, Shield Box, CBA Unit D5 Jack Holder [10] Speaker [6] Inverter CBA Step/ Loc. No. Part [14] Front Cabinet ↓ (1) ↓ (2) ↓ (4) *1: Refer to the following "Reference Notes in the Table." Note *2: 32MD311B/F7 Note: [1] Stand Assembly D1 4(S-1) --- [2] Rear Cabinet D1 13(S-2), 2(S-3), 3(S-4) --- [3] DVD Holder D2 4(S-5), 4(S-6), CN901, D5 CN902 --- (1) Order of steps in procedure. When reassembling, follow the steps in reverse order. These numbers are also used as the Identification (location) No. of parts in figures. (2) Parts to be removed or installed. (3) Fig. No. showing procedure of part location [4] (S-7a), 2(S-7b)*1, DVD D2 CN201, CN301, Mechanism D5 CN801 1 2 3 4 5 6 [5] DVD Main CBA Unit D2 --------------D5 --- [6] Inverter CBA 6(S-8), CN1001, D3 CN1003, CN1050, D5 CN1100, CN1150, CN1200, CN1900 --- [7] Jack CBA D3 2(S-9), CL701B D5 --- [8] Power Supply CBA 7(S-10), CN101, D3 CN301, CN302, D5 CN303, CN801, CN802 --- (4) Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered. P = Spring, L = Locking Tab, S = Screw, H = Hex Screw, CN = Connector e.g. 2(S-2) = two Screws of (S-2), 2(L-2) = two Locking Tabs of (L-2) (5) Refer to the following "Reference Notes in the Table." 5-1 FL11.11-A_DC Reference Notes 2) Rotate the gear in the direction of the arrow as shown below. 1. CAUTION 1: Electrostatic breakdown of the laser diode in the optical system block may occur as a potential difference caused by electrostatic charge accumulated on cloth, human body etc., during unpacking or repair work. To avoid damage of pickup follow next procedures. 1) Short-circuit the three short lands of FPC cable with solder before removing the FFC cable (CN201). If you disconnect the FFC cable (CN201) before short-circuiting the three short lands of FPC cable, the laser diode of pickup will be destroyed. (Fig. D2) 2) Disconnect the connectors (CN301 and CN801). Remove the screw (S-7a) and remove the DVD Main CBA Unit. (Fig. D2) 2. Reassembly Notes of New DVD Mechanism: B a. To remove the Chassis Cover, remove the two screws (S-7b) as shown in Fig. D2. b. To avoid damaging the pickup unit (laser diode), confirm that the three short lands (either of two places) are short-circuited by soldering as shown in Fig. D2. View from the "B" angle c. Connect the FFC cables of the new DVD Mechanism to the three connectors (CN201, CN301, CN801) on the DVD Main CBA Unit. d. After confirming that the FFC cables are securely connected to the three connectors, remove the solder from the three short lands. If the solder is not removed, the laser diode will not light and it will not be possible to read discs. e. Insert the Pin on the Chassis Cover into the Hole on the Main Chassis as shown in Fig. D2. Then tighten the two screws (S-7b) to install the Chassis Cover. The gear is turned to the direction of the arrow. 3. CAUTION 2: When reassembling, confirm the FFC cable (CN201) is connected completely. Then remove the solder from the three short lands of FPC cable. (Fig. D2) 6. How to eject manually 2 1) Remove the Rear Cabinet. 2) To remove the DVD Main CBA Unit, remove the screw (S-7a) in Fig. D2. Do not disconnect connectors. 4. How to eject a disc in emergency Press and hold [EJECT] on the unit for more than 5 seconds. 3) To remove the Chassis Cover, remove the two screws (S-7b) as shown in Fig. D2. 5. How to eject manually 1 4) Remove a disc. 1) Remove the Rear Cabinet. 5-2 FL11.11-A_DC (S-2) (S-4) [2] Rear Cabinet (S-4) (S-2) (S-3) (S-2) (S-4) (S-2) (S-2) [1] Stand Assembly (S-1) Fig. D1 5-3 FL11.11-A_DC (S-5) (S-7a) [5] DVD Main CBA Unit [4] DVD Mechanism A [3] DVD Holder (S-6) Remove the two screws (S-7b), then short-circuit the three short lands by soldering as shown in View from the "A" angle. Chassis Cover Pin (S-7b) Either of two places A FPC Cable View from the "A" angle Hole Main Chassis Fig. D2 5-4 FL11.11-A_DC [6] Inverter CBA (S-8) (S-10) (S-8) [7] Jack CBA (S-12) (S-9) (S-10) Shield Box (S-10) (S-12) [9] Digital Main CBA Unit [8] Power Supply CBA (S-11) (S-12) (S-11) Jack Holder Fig. D3 5-5 FL11.11-A_DC [LD320SS2, 32MD301B/F77] [14] Front Cabinet (S-13) Hook [10] Speaker Speaker Holder (R) [12] Function CBA (S-15) [11] IR Sensor CBA (S-14) (S-13) Hook [10] Speaker Speaker Holder (L) [32MD311B/F7] [14] Front Cabinet [10] Speaker Speaker Holder (R) [13] LCD Module Assembly (S-13) Hook Function Knob (S-14) Shield Plate [12] Function CBA LED Lens Speaker Holder (L) (S-15) (S-14) Hook [11] IR Sensor CBA (S-13) (S-16) [10] Speaker Fig. D4 5-6 FL11.11-A_DC TV Cable Wiring Diagram To DVD Mechanism To LCD Module Assembly CN201 CN301 CN801 CN401 CN601 DVD Main CBA Unit Inverter CBA CN1050 Jack CBA CL701B Power Supply CBA CN902 CN1100 CN201 CN1001 CN901 CN1150 CL701A CN303 CN602 CN302 CN1900 CN301 CN101 CN1200 AC CORD CN802 CN801 CN1003 To Speaker To Speaker To LCD Module Assembly CN3003 CN3006 CN3002 CN3005 Digital Main CBA Unit IR Sensor CBA Function CBA CL103B CL103C CL101B To LCD Module Assembly Fig. D5 5-7 FL11.11-A_DC ELECTRICAL ADJUSTMENT INSTRUCTIONS How to set up the service mode: General Note: “CBA” is abbreviation for “Circuit Board Assembly.” Service mode: Note: Electrical adjustments are required after replacing circuit components and certain mechanical parts. It is important to perform these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available. 1. Turn the power on. 2. Press [MENU] button to display Setup menu. 3. Select “Features”. 4. Select “Current Software Info”. 5. Press [0], [4], [2], [5], [7], [4] and [INFO] buttons on the remote control unit in this order. The following screen appears. Test Equipment Required 1. NTSC Pattern Generator (Color Bar W/White Window, Red Color, Dot Pattern, Gray Scale, Monoscope, Multi-Burst) "*" differs depending on the models. Code : *******-***-*-*****-**** Pic code : **-*******-*****-** 2. Remote control unit MIPS : Push 0key 3. Color Analyzer Press "POWER" key to exit. Tuner : ****-*****-**** Safety : safety_Non 6-1 FL11.11EA 1. Purity Check Mode 2. VCOM Adjustment This mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels. Test Point Adj. Point 1. Enter the Service mode. Screen 2. Each time the [7] button on the remote control unit is pressed, the display changes as follows. [CHANNEL UP/DOWN ] buttons M. EQ. Spec. Color analyzer See below Purity Check Mode Figure White mode To avoid interference from ambient light, this adjustment should be performed in a dark room. [7] button Perpendicularity [7] button Black mode L = 1.18 inches Color Analyzer [7] button Red mode 1. Operate the unit for more than 60 minutes. 2. Set the color analyzer at the zero point calibration and bring the optical receptor pointing at the center of the LCD-Panel at a distance of 1.18 inches(3cm) away from the LCD-Panel surface. Note: The optical receptor must be set perpendicularly to the LCD Panel surface. [7] button Green mode 3. Enter the Service mode. 4. Press [3] button on the remote control unit. 5. Press [CHANNEL UP/DOWN] buttons on the remote control unit so that the color analyzer value becomes minimum. [7] button Blue mode 6. To cancel or to exit from the VCOM Adjustment, press [CH RETURN] or [PREV CH] button. [7] button White 20% mode Note: When entering this mode, the default setting is White mode. 3. To cancel or to exit from the Purity Check Mode, press [CH RETURN] or [PREV CH] button. 6-2 FL11.11EA The White Balance Adjustment should be performed when replacing the LCD Panel or Digital Main CBA. Purpose: To mix red and blue beams correctly for pure white. 5. [CUTOFF] Press [1] button to select “COR” for Red Cutoff adjustment. Press [3] button to select “COB” for Blue Cutoff adjustment. [DRIVE] Press [4] button to select “DR” for Red Drive adjustment. Press [6] button to select “DB” for Blue Drive adjustment. Symptom of Misadjustment: White becomes bluish or reddish. 6. In each color mode, press [CHANNEL UP/DOWN] buttons to adjust the values of color. Test Point Adj. Point 7. Adjust Cutoff and Drive so that the color temperature becomes 12000°K (x= 0.272 / y= 0.278 ±0.005). 3. White Balance Adjustment Screen [VOLUME DOWN] button Mode Input [VIDEO1] C/D White Raster (APL 70%) or (APL 40%) M. EQ. Spec. Pattern Generator, Color analyzer x= 0.272 ± 0.005 y= 0.278 ± 0.005 8. To cancel or to exit from the White Balance Adjustment, press [CH RETURN] or [PREV CH] button. Figure To avoid interference from ambient light, this adjustment should be performed in a dark room. Perpendicularity L = 1.18 inches Color Analyzer INPUT: WHITE 70%, 40% 1. Operate the unit for more than 60 minutes. 2. Input the White Raster(70%=70IRE, 40%=40IRE). INPUT SIGNAL 0IRE 0IRE Low Light Hight Light 100IRE 100IRE 40%=40IRE 70%=70IRE 3. Set the color analyzer at the CHROMA mode and zero point calibration. Bring the optical receptor pointing at the center of the LCD-Panel at a distance of 1.18 inches(3cm) away from the LCDPanel surface. Note: The optical receptor must be set perpendicularly to the LCD Panel surface. 4. Enter the Service mode. Press [VOLUME DOWN] button on the remote control unit and select “C/D” mode. 6-3 FL11.11EA HOW TO INITIALIZE THE LCD TV/DVD The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to select a language and program channels after the set has been initialized. To put the program back at the factory-default, initialize the LCD TV/DVD using the following procedure. < DVD Section > < LCD TV Section > 1. Turn the power on. 1. Turn the power on. 2. To enter the service mode, press the service button on the service remote control unit. 2. Enter the service mode. - To cancel the service mode, press [POWER] button on the remote control unit. - To cancel the service mode, press [POWER] button on the service remote control unit. 3. Press [INFO] button on the remote control unit to initialize the LCD television. 3. To put the LCD TV/DVD into the DVD mode, press [CH RETURN] or [PREV CH] on the remote control unit. 4. “INITIALIZED” will appear in the upper right of the screen. “INITIALIZED” color will change to green from red when initializing is completed. 4. To put the LCD TV/DVD into the Flash clear mode, press [INPUT SELECT] or [SOURCE] buttons on the remote control unit within five seconds. The following screen appears. Flash Memory Clear : OK CHUCKING ON When “OK” appears on the screen, the factory default will be set. 5. To exit this mode, press[CHANNEL UP/DOWN] button to go to TV mode, or press [POWER] button to turn the power off. Note: The name of buttons may vary with the brand of unit. 7-1 FL11.11INT FIRMWARE RENEWAL MODE < DVD Section > 5. After programming is finished, the disc will be ejected automatically. Fig. c appears on the screen and the checksum will be shown in (*2). 1. Turn the power on and press [EJECT] button on the remote control unit to put the LCD TV/DVD into DVD mode. Then remove the disc. "*******" differ depending on the models. 2. To put the LCD TV/DVD into F/W version up mode, press [9], [8], [7], [6], and [MODE] buttons on the remote control unit in this order. Fig. a appears on the screen. F/W Version Up Mode (*2) VERSION : Completed SUM : **** Model No : ****** VERSION : *.** ************.*** "*******" differs depending on the models. F/W Version Up Mode Model No : ****** VERSION : *.** Please insert a DISC for F/W Version Up. Fig. c Completed Program Mode Screen At this time, no button is available. 6. Remove the disc. EXIT: SELECT 7. Unplug the AC cord from the AC outlet then plug in again. Fig. a Version Up Mode Screen 8. Press [EJECT] button on the remote control unit to put the LCD TV/DVD into DVD mode again. 3. Insert the disc for version up into the disc slot. 9. Press [1], [2], [3], [4], and [INFO] buttons on the remote control unit in this order. Fig. d appears on the screen. 4. The LCD TV/DVD enters the F/W version up mode automatically. Fig. b appears on the screen. Make sure to insert the proper F/W for the state of this model. "*******" differs depending on the models. "*******" differ depending on the models. F/W Version Up Mode (*1) VERSION : Reading... MODEL : ****** Version : *.** Region : * Model No : ****** VERSION : *.** ************.*** EEPROM CLEAR : CLEAR Fig. d 10. Press [CLEAR] button on the remote control unit. Fig. e appears on the screen. Fig. b Programing Mode Screen "*******" differs depending on the models. The appearance shown in (*1) of Fig. b is described as follows: No. Appearance State 1 Reading... Sending files into the memory 2 Erasing... Erasing previous version data 3 Programming... Writing new version data EXIT: SELECT MODEL : ****** Version : *.** Region : * EEPROM CLEAR : OK EEPROM CLEAR : CLEAR EXIT: SELECT Fig. e When “OK” appears on the screen, the factory default will be set. The firmware renewal mode is now complete. 11. To exit this mode, press [CHANNEL UP/DOWN] button to go to TV mode, or press [POWER] button to turn the power off. 8-1 FL11.11FW < LCD TV Section > The appearance shown in *1 is described as follows. Appearance Equipment Required a. USB storage device b. Remote Control Unit Firmware Update Procedure Upgrade the firmware only. The setting values are not initialized. Factory upgrade Upgrade the firmware and initialize the setting values. Downloading... Downloading the firmware from the USB storage device. Writing... Writing the downloaded firmware in flash memory. Checking... Checking the new firmware. 5. When the firmware update is completed, the following will appear on the screen. Note: There are two states (the User Upgrade and the Factory Upgrade) in firmware update. User Upgrade State Software Upgrade The identification of User Upgrade and Factory Upgrade are done by the filename. The software upgrade is completed. Remove USB storage device, turn TV off then on again. 1. Turn the power off and unplug the AC Cord. 2. Insert the USB storage device to the USB port as shown below. Remove the USB storage device from the USB port. Turn the power off and turn the power on again. Rear Cabinet Note: When the Factory Upgrade is used, after restarting TV, shift to initial screen menu in service mode. "INITIALIZED" will appear on the upper right of the screen. "INITIALIZED" color will change to green from red when initializing is completed. USB storage device 3. Plug the AC cord in the wall outlet and turn the power on. 4. The update will start and the following will appear on the screen. "*" differs depending on the models. Software Upgrade Software upgrade in progress. Please wait. Do not remove the USB storage device or turn the TV off while upgrade is in progress. Current Version: *******-***-*-***-**** New Version: *******-***-*-***-**** *1 Downloading... 0% Note: If the above screen isn’t displayed, repeat from step 1. 8-2 FL11.11FW TROUBLESHOOTING [ Power Supply Section ] FLOW CHART NO.1 The power cannot be turned on. No Is the fuse (F601) normal? See FLOW CHART No.2 <The fuse blows out.> Yes Is normal state restored when once unplugged power cord is plugged again several seconds? No Yes Is the AL+33V line voltage normal? No Check if there is any leak or short-circuiting on the primary circuit component, and service it if defective. (C605, D601, D602, D603, D604, Q601, Q602, T601) Yes Check each rectifying circuit of the secondary circuit and service it if defective. FLOW CHART NO.2 The fuse blows out. Check the presence that the primary component is leaking or shorted and service it if defective. Check the presence that the rectifying diode or circuit is shorted in each rectifying circuit of secondary side, and service it if defective. After servicing, replace the fuse. FLOW CHART NO.3 When the output voltage fluctuates. Does the photocoupler circuit on the secondary side operate normally? No Check IC601, D652, Q631 and their periphery circuit, and service it if defective. Yes Check IC601, D609, D611 and their periphery, circuit and service it if defective. FLOW CHART NO.4 When buzz sound can be heard in the vicinity of power circuit. Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side, and service it if defective. (IC631, Q207, Q209, Q210, Q211, Q501, Q635, Q636, Q637, Q640, Q641, Q642, Q643, D631, D632, D633, D634, D638, D641, D642, D646, D647) FLOW CHART NO.5 AL+33V is not output. Is approximately +34V voltage supplied to the cathode of D638? No Check C638, D638, D639 and their periphery circuit, and service it if defective. Yes Check D657, R661 and their periphery circuit, and service it if defective. 9-1 FL11.11TR FLOW CHART NO.6 LCD+24.5V is not output. Is approximately +30V voltage supplied to the collector of Q210? No See FLOW CHART No.5 <AL+33V is not output.> Yes Check Q207, Q208, D205, P-ON-H1 line and their periphery circuit, and service it if defective. FLOW CHART NO.7 LCD+16V is not output. Is approximately +19V voltage supplied to the collector of Q209? No Check C631, D631, D635 and their periphery circuit, and service it if defective. Yes Is approximately +16V voltage supplied to the base of Q209? No Check Q207, Q208, D203, D204, D211 and their periphery circuit, and service it if defective. Yes Replace Q209. FLOW CHART NO.8 INV+16V is not output. Is approximately +19V voltage supplied to the collector of Q501? No Check C631, D631, D635 and their periphery circuit, and service it if defective. Yes Is approximately +16V voltage supplied to the base of Q501? No Check Q207, Q208, D203, D204, D211 and their periphery circuit, and service it if defective. Yes Replace Q501. FLOW CHART NO.9 P-ON+7V is not output. Is approximately +7V voltage supplied to the collector of D646? No Check C644, D646 and their periphery circuit, and service it if defective. Yes Check if there is any leak or short-circuit on the loaded circuit, and service it if defective. 9-2 FL11.11TR FLOW CHART NO.10 P-ON+5V is not output. (LCD+16V is outputted normally.) Is approximately +6.8V voltage supplied to the collector of Q643? No See FLOW CHART No.9 <P-ON+7V is not output.> Yes Is approximately +6V voltage supplied to the base of Q641 and the base of Q643? No Check D645 and their periphery circuit, and service it if defective. Yes Replace Q641 and Q643. FLOW CHART NO.11 P-ON+5V(TUNER+5V) is not output. (LCD+16V is outputted normally.) Is approximately +6.7V voltage supplied to the collector of Q640? No See FLOW CHART No.9 <P-ON+7V is not output.> Yes Is approximately +6V voltage supplied to the base of Q641 and the base of Q643(Q640)? No Check D645 and their periphery circuit, and service it if defective. Yes Replace Q641 and Q643(Q640). FLOW CHART NO.12 AL+13V(M+13V) is not output. Is approximately +13V voltage supplied to the cathode of D641 and D642? No Check C639, D642 and their periphery circuit, and service it if defective. Yes Check if there is any leak or short-circuit on the loaded circuit, and service it if defective. FLOW CHART NO.13 D+5.5V is not output. Is approximately +5V voltage supplied to the cathode of D634? No Check C634, D634 and their periphery circuit, and service it if defective. Yes Check if there is any leak or short-circuit on the loaded circuit, and service it if defective. 9-3 FL11.11TR FLOW CHART NO.14 P-ON+3V is not output. Is approximately +3V voltage supplied to the cathode of D647? No Check C645, D647 and their periphery circuit, and service it if defective. Yes Check if there is any leak or short-circuit on the loaded circuit, and service it if defective. FLOW CHART NO.15 P-ON+3.3V is not output. Is approximately +5V voltage supplied to the cathode of D633? No Check C633, D633 and their periphery circuit, and service it if defective. Yes Is the "H" signal (approximately +3.5V) inputted to the base of Q637? No Check Q638, Q639, P-ON-H2 line and their periphery circuit, and service it if defective. Yes Replace Q637. FLOW CHART NO.16 EV+3.3V is not output. Is approximately +4.6V voltage supplied to the collector of Q903? No See FLOW CHART No.13 <D+5.5V is not output.> Yes Check Q903, D905 and their periphery circuit, and service it if defective. FLOW CHART NO.17 DVD-ON+3.3V is not output. Is approximately +5V voltage supplied to the collector of Q904? No See FLOW CHART No.13 <D+5.5V is not output.> Yes Check Q904, D906, and their periphery circuit, and service it if defective. FLOW CHART NO.18 EV+9V is not output. Is approximately +13V voltage supplied to the anode of D909? No See FLOW CHART No.14 <P-ON+3V is not output.> Yes Check D901, D902, D903, D909 and their periphery circuit, and service it if defective. 9-4 FL11.11TR FLOW CHART NO.19 EV+1.2V is not output. Is approximately +5V voltage supplied to the emitter of Q901? No See FLOW CHART No.13 <D+5.5V is not output.> Yes Is approximately +4V voltage supplied to Pin(3) of IC901? No Check Q901, Q902, DVD-MAIN PWR line and their periphery circuit, and service it if defective. Yes Replace IC901. FLOW CHART NO.20 P-ON+9V is not output. (LCD+16V is outputted normally.) Is approximately +13V voltage supplied to the collector of Q642? No See FLOW CHART No.12 <AL+13V(M+13V) is not output.> Yes Is approximately +10V voltage supplied to the base of Q642? No Check D670 and their periphery circuit, and service it if defective. Yes Replace Q642. FLOW CHART NO.21 AL+3.3V is not output. Is approximately +34V voltage supplied to the collector of Q635? No See FLOW CHART No.5 <AL+33V is not output.> Yes Is approximately +5V voltage supplied to Pin(1) of IC631? No Check Q635, D659 and their periphery circuit, and service it if defective. Yes Replace IC631. FLOW CHART NO.22 LCD-6.8V is not output. Is approximately -9V voltage supplied to the Anode of D632? No Check C632, D632 and their periphery circuit, and service it if defective. Yes Is approximately -8V voltage supplied to the base of Q211? No Check Q207, Q208, D205, P-ON-H1 line and their periphery circuit, and service it if defective. Yes Replace Q211. 9-5 FL11.11TR [ Video Signal Section ] FLOW CHART NO.1 The key operation is not functioning. Are the contact point and installation state of the key switches (SW101A, SW103A~SW107A, SW151~SW153) normal? No Re-install the switches (SW101A, SW103A~SW107A, SW151~SW153) correctly or replace the poor switch. Yes When pressing each switches (SW101A, SW103A~ SW107A, SW151~SW153) do the voltage of Pin(29) of CN302 and Pin(2) of CN303 decrease? No Check the switches (SW101A, SW103A~SW107A, SW151~SW153) and their periphery, and service it if defective. Yes Replace Digital Main CBA Unit. FLOW CHART NO.2 No operation is possible from the remote control unit. Operation is possible from the unit. Is 3.3V voltage supplied to Pin(2) terminal of the remote control receiver (RS102)? No Check AL+3.3V line and service it if defective. Yes No Is the "L" pulse sent out Pin(1) terminal of remote control receiver (RS102) when the infrared remote control is activated? Replace the remote control receiver(RS102) or the remote control unit. Yes Is the "L" pulse supplied to Pin(25) of CN301? No Yes Check the line between Pin(1) terminal of remote control receiver(RS102) and Pin(25) of CN301, and service it if defective. Replace Digital Main CBA Unit. FLOW CHART NO.3 Picture does not appear normally.(Video input) Are the video signal inputted to Pin(4) of CN302? No Yes Check the line between Pin(4) of CN302 and JK752, and service it if defective. Replace Digital Main CBA Unit or LCD Module Assembly. 9-6 FL11.11TR FLOW CHART NO.4 Picture does not appear normally.(Tuner input) Are the DIF signal inputted to the Pin(26,28) of CN302? No Yes Check the line between Pin(26, 28) of CN302 and Pin(10, 11) of TU301, and service it if defective. Replace Digital Main CBA Unit or LCD Module Assembly. FLOW CHART NO.5 Picture does not appear normally.(S-Video input) Are the video signal outputted to the Pin(6, 8) of CN302? No Check the line between Pin(6, 8) of CN302 and JK751, and service it if defective. Pin(6): S-VIDEO-C Pin(8): S-VIDEO-Y Yes Replace Digital Main CBA Unit or LCD Module Assembly. FLOW CHART NO.6 Picture does not appear normally.(Y/Pb/Pr input) Are the video signal inputted to the Pin(15, 17, 19) of CN302? No Pin(15): VIDEO-Y Pin(17): VIDEO-Pb Pin(19): VIDEO-Pr Check the line between Pin(15, 17, 19) of CN302 and input terminals(JK731, JK732, JK733), and service it if defective. Yes Replace Digital Main CBA Unit or LCD Module Assembly. FLOW CHART NO.7 Picture does not appear normally.(DVD PB) Are the video signal inputted to the Pin(1, 3, 5) of CN902? No Replace DVD Main CBA Unit. Pin(5) : DVD-Y Pin(3) : DVD-Pb Pin(1) : DVD-Pr Yes Replace Digital Main CBA Unit or LCD Module Assembly. 9-7 FL11.11TR [ Audio Signal Section ] FLOW CHART NO.1 Audio is not outputted normally.(Audio input) Are the audio(L/R) signals inputted to Pin(2, 15) of IC771? No Yes Are the audio(L/R) signals inputted to each pin of CN301? Pin(6) : Pin(8) : Pin(2) : Pin(4) : No Check the line between Pin(2, 15) of IC771 and input terminal(JK753, JK754), and service it if defective. Replace Digital Main CBA Unit. AMP(L)-OUT AMP(R)-OUT AUDIO(L)-OUT AUDIO(R)-OUT Yes Are the audio(L/R) signals inputted to the Pin(1, 44) of IC801? No Check the line between Pin(6, 8) of CN301 and Pin(1, 44) of IC801, and service it if defective. Are the audio(L/R) signals inputted to the Pin(3, 5) of IC871? No Check the line between Pin(2, 4) of CN301 and Pin(3, 5) of IC871, and service it if defective. Yes Are the audio(L/R) signals outputted to the Pin(1, 2) of CN801 and CN802? CN801: SP(L) CN802: SP(R) No Yes Are the audio(L/R) signals outputted to the audio output terminal? JK871: AUDIO(L)-OUT JK872: AUDIO(R)-OUT No 9-8 Check IC801 and their periphery circuit, and service it if defective. Check SP801,SP802 and their periphery circuit, and service it if defective. Check the line between Pin(1, 7) of IC871 and audio output terminal(JK871, JK872), and service it if defective. FL11.11TR FLOW CHART NO.2 Audio is not outputted normally.(Component Audio input) Are the audio(L/R) signals inputted to the Pin(4, 11) of IC771? No Yes Are the audio(L/R) signals inputted to each pin of CN301? Pin(6) : Pin(8) : Pin(2) : Pin(4) : No Check the line between Pin(4, 11) of IC771 and input terminal(JK741, JK742), and service it if defective. Replace Digital Main CBA Unit. AMP(L)-OUT AMP(R)-OUT AUDIO(L)-OUT AUDIO(R)-OUT Yes Are the audio(L/R) signals inputted to the Pin(1, 44) of IC801? No Check the line between Pin(6, 8) of CN301 and Pin(1, 44) of IC801, and service it if defective. Are the audio(L/R) signals inputted to the Pin(3, 5) of IC871? No Check the line between Pin(2, 4) of CN301 and Pin(3, 5) of IC871, and service it if defective. Yes Are the audio(L/R) signals outputted to the Pin(1, 2) of CN801 and CN802? CN801: SP(L) CN802: SP(R) No Yes Are the audio(L/R) signals outputted to the audio output terminal? JK871: AUDIO(L)-OUT JK872: AUDIO(R)-OUT No 9-9 Check IC801 and their periphery circuit, and service it if defective. Check SP801,SP802 and their periphery circuit, and service it if defective. Check the line between Pin(1, 7) of IC871 and audio output terminal(JK871, JK872), and service it if defective. FL11.11TR FLOW CHART NO.3 Audio is not outputted normally.(Tuner input) Are the DIF signals outputted to the Pin(26, 28) of CN302? No Check TU301 and their periphery circuit, and service it if defective. Yes Are the audio(L/R) signals inputted to each pin of CN301? Pin(6) : Pin(8) : Pin(2) : Pin(4) : No Replace Digital Main CBA Unit. AMP(L)-OUT AMP(R)-OUT AUDIO(L)-OUT AUDIO(R)-OUT Yes Are the audio(L/R) signals inputted to the Pin(1, 44) of IC801? No Check the line between Pin(6, 8) of CN301 and Pin(1, 44) of IC801, and service it if defective. Are the audio(L/R) signals inputted to the Pin(3, 5) of IC871? No Check the line between Pin(2, 4) of CN301 and Pin(3, 5) of IC871, and service it if defective. Yes Are the audio(L/R) signals outputted to the Pin(1, 2) of CN801 and CN802? CN801: SP(L) CN802: SP(R) No Yes Are the audio(L/R) signals outputted to the audio output terminal? JK871: AUDIO(L)-OUT JK872: AUDIO(R)-OUT No 9-10 Check IC801 and their periphery circuit, and service it if defective. Check SP801,SP802 and their periphery circuit, and service it if defective. Check the line between Pin(1, 7) of IC871 and audio output terminal(JK871, JK872), and service it if defective. FL11.11TR 10-1 X3101 25MHz OSC 6 5 2 1 3 DIGITAL MAIN CBA UNIT SCK SI SO CS WP IC3006 (MEMORY) TO AUDIO BLOCK DIAGRAM C7-SPD-EN DVD-SPD-EN INPUT0 INPUT1 AUDIO-MUTE SCK SIN SOUT CS WP H21 G22 H22 AB21 W20 W17 Q3006 T19 U20 U21 N21 M19 M3 U19 DVD-REMOTE W18 LED-CONT L21 DVD-P-ON V20 Q3033 BUFFER AL+3.3V SCL K3 SDA K2 PROTECT1 PROTECT2 PROTECT3 VCOM-PWM BACKLIGHT-SW BACKLIGHT-ADJ C7-SPD-EN DVD-SPD-EN INPUT0 INPUT1 AUDIO-MUTE DVD-SDATA DVD-SCLK DVD-CS DVD-DISC-IN DVD-DISC-OUT T22 XIN25 DVD-AUDIO-MUTE T21 XOUT25 DVD-MAIN-PWR V19 Y21 AA22 Y20 AA21 Y17 W22 K1 L4 L19 PROTECT1 PROTECT2 PROTECT3 VCOM-PWM BACKLIGHT-SW BACKLIGHT-ADJ 16 6 7 8 13 11 9 15 25 5 CN3003 LED-CONT DVD-P-ON DVD-REMOTE DVD-SDATA DVD-SCLK DVD-CS DVD-DISC-IN DVD-DISC-OUT DVD-AUDIO-MUTE DVD-MAIN-PWR 22 SCL 21 SDA CN3006 11 15 5 29 26 28 CN3002 Q3005 CN303 16 6 7 8 13 11 9 15 25 5 CN302 22 21 CN301 11 15 5 29 26 28 REMOTE LED1 P-ON-H2 P-ON-H1 REMOTE LED1 P-ON-H2 P-ON-H1 CN301 25 27 1 9 CN3002 25 27 1 9 KEY-IN2 G20 KEY-IN1 G21 K21 K19 K20 Y22 CN302 29 CN3006 29 KEY-IN1 DVD-LED L20 CN303 2 3 CN3003 2 KEY-IN2 3 DVD-LED IC3005 (MAIN MICRO CONTROLLER) DVD-MAIN-PWR P-ON-H2 P-ON-H1 PROTECT1 PROTECT2 * TU301 (TUNER UNIT) (TUNER UNIT) POWER SUPPLY CBA 4 SCL 5 SDA * TU301 9 SCL 8 SDA LED-CONT DVD-P-ON DVD-REMOTE DVD-SDATA DVD-SCLK DVD-CS DVD-DISC-IN DVD-DISC-OUT 6 5 4 14 CN201 CN401 2 26 25 24 21 22 23 3 TO INVERTER BLOCK DIAGRAM (CN1001) LED-CONT DVD-P-ON DVD-REMOTE DVD-SDATA DVD-SCLK DVD-CS DVD-DISC-IN DVD-DISC-OUT PROTECT3 BACKLIGHT-SW BACKLIGHT-ADJ VCOM FUNCTION CBA CL103B KEY SWITCH 3 KEY SWITCH 4 DVD MAIN CBA UNIT TO DVD DIGITAL SIGNAL PROCESS BLOCK DIAGRAM TO DVD SYSTEM CONTROL / SERVO BLOCK DIAGRAM CL103C 3 KEY-IN1 4 KEY-IN2 CN601 DVD-AUDIO-MUTE 10 DVD-AUDIO-MUTE 13 CN902 2 26 25 24 21 22 23 3 CN901 D106 DVD D104 POWER AL+3.3V D105 STANDBY IR SENSOR CBA CL101B 2 5 4 6 7 8 TO POWER SUPPLY BLOCK DIAGRAM REMOTE P-ON-H1 LED1 KEY-IN1 KEY-IN2 DVD-LED Either TU301 is used for Power Supply CBA. IC201,Q203, Q204,Q205 DRIVE Q171 Q172 CN101 2 5 4 6 7 8 REMOTE RS102 SENSOR 1. System Control Block Diagram BLOCK DIAGRAMS FL11.11BLS 10-2 Y JK731 COMPONENT -Y-IN JK732 COMPONENT -Pb-IN JK733 COMPONENT -Pr-IN JACK CBA C CL701B 5 3 1 2 VIDEO-IN S-VIDEO-C-IN S-VIDEO-Y-IN S-VIDEO-SW-IN DIF-OUT1 13 DIF-OUT2 12 IF-AGC 14 (TUNER UNIT) * TU301 DIF-OUT1 11 DIF-OUT2 10 IF-AGC 9 Either TU301 is used for Power Supply CBA. * TU301 (TUNER UNIT) JK751 S-VIDEO -IN JK752 VIDEO-IN CL701A 5 3 1 2 POWER SUPPLY CBA WF4 WF2 WF9 WF5 WF3 WF8 WF10 WF6 WF1 VIDEO-IN S-VIDEO-C-IN S-VIDEO-Y-IN S-VIDEO-SW COM-VIDEO-Y-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN 1 DVD-Pr 3 DVD-Pb 5 DVD-Y CN902 CN302 26 DIF-OUT1 28 DIF-OUT2 24 IF-AGC 22 DVD-Y 20 DVD-Pb 18 DVD-Pr CN303 CN302 4 6 8 5 15 17 19 CN601 4 6 8 CN3006 26 28 24 CN3003 22 20 18 CN3006 4 6 8 5 15 17 19 DVD MAIN CBA UNIT DVD-Pr DVD-Pb DVD-Y DIF-OUT1 DIF-OUT2 IF-AGC DVD-Y DVD-Pb DVD-Pr VIDEO-IN S-VIDEO-C-IN S-VIDEO-Y-IN S-VIDEO-SW COM-VIDEO-Y-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN DIGITAL MAIN CBA UNIT AUDIO SIGNAL TO DVD DIGITAL SIGNAL PROCESS BLOCK DIAGRAM TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM VIDEO SIGNAL 2. Video Block Diagram FL11.11BLV JACK CBA 10-3 Q873,Q874 DRIVE SP802 SPEAKER R-CH SP801 SPEAKER L-CH JK841 DIGITAL AUDIO-OUT (COAXIAL) CN801 SP(L)+ 2 SP(L)- 1 CN802 SP(R)+ 2 SP(R)- 1 CL801 CL802 BUFFER Q841 DRIVE2 35,36 31,32 PWM2 PWM1 44 1 Q771 13 3 POWER SUPPLY CBA 20 MUTE CONTROL DRIVE1 9,10 13,14 5 3 9 10 CONTROL LOGIC IC871 (OP AMP) IC801 (AUDIO AMP) 7 MUTE 2 4 1 5 IC771 (AUDIO SELECTOR) 15 11 12 14 JK872 AUDIO(R)-OUT Q872 MUTE CL701A 7 9 1 Q871 CL701B 7 AUDIO(L)-IN 9 AUDIO(R)-IN JK871 AUDIO(L)-OUT JK721 HDMIAUDIO(L)-IN JK722 HDMIAUDIO(R)-IN JK741 COMPONENTAUDIO(L)-IN JK742 COMPONENTAUDIO(R)-IN JK753 AUDIO(L) -IN JK754 AUDIO(R) -IN Q772 Q801 7 1 IC951 (OP AMP) WF12 5 3 CN902 CN601 9 DVD-AUDIO(L) 12 11 DVD-AUDIO(R) 14 13 DVD-SPDIF 16 WF7 AUDIO(L)-OUT AUDIO(R)-OUT AMP(L)-OUT AMP(R)-OUT CN303 28 DVD-SPDIF CN302 2 SPDIF 20 AUDIO-MUTE CN301 2 4 6 8 CN302 10 INPUT1 12 INPUT0 CN302 13 AUDIO(L) 11 AUDIO(R) CN3003 28 CN3006 2 20 CN3002 2 4 6 8 10 12 CN3006 CN3006 13 11 CN303 CN3003 24 DVD-AUDIO(L) 24 26 DVD-AUDIO(R) 26 WF13 WF11 4 4 2 2 6 2 8 7 6 5 C7-SPD-EN DVD-SPD-EN C7-SPDIF AMP(L)-OUT AMP(R)-OUT LRCLK BCLK ADATA1 ACLK DIGITAL MAIN CBA UNIT 1 IC3017 (BUFFER GATE) 1 IC3016 (BUFFER GATE) 7 1 IC3015 (OP AMP) (L-CH) D/A 15 (R-CH) CONVERTER 14 IC3010 (D/A CONVERTER) INPUT1 INPUT0 AUDIO-MUTE AUDIO(L) AUDIO(R) DVD-AUDIO(L) DVD-AUDIO(R) DVD-AUDIO(L) DVD-AUDIO(R) DVD-SPDIF DVD MAIN CBA UNIT TO SYSTEM CONTROL BLOCK DIAGRAM TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM TO SYSTEM CONTROL BLOCK DIAGRAM TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM TO DVD DIGITAL SIGNAL PROCESS BLOCK DIAGRAM AUDIO SIGNAL 3. Audio Block Diagram FL11.11BLA 10-4 JK3004 HDMI-IN2 JK3003 HDMI-IN1 7 9 4 6 1 3 10 12 16 15 7 9 4 6 1 3 10 12 16 15 Q3020 Q3018 TMDS-D0(+) TMDS-D0(-) TMDS-D1(+) TMDS-D1(-) TMDS-D2(+) TMDS-D2(-) TMDS-CLOCK(+) TMDS-CLOCK(-) SDA SCL TMDS-D0(+) TMDS-D0(-) TMDS-D1(+) TMDS-D1(-) TMDS-D2(+) TMDS-D2(-) TMDS-CLOCK(+) TMDS-CLOCK(-) SDA SCL TO AUDIO BLOCK DIAGRAM TO VIDEO BLOCK DIAGRAM BUFFER Q3016 BUFFER Q3015 C7-SPDIF BCLK LRCLK ACLK ADATA1 BUFFER BUFFER DVD-AUDIO(L) DVD-AUDIO(R) AUDIO(L) AUDIO(R) AMP(L)-OUT AMP(R)-OUT IF-AGC S-VIDEO-SW DIF-OUT1 DIF-OUT2 VIDEO-IN S-VIDEO-C-IN S-VIDEO-Y-IN COM-VIDEO-Y-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN DVD-Y DVD-Pb DVD-Pr DIGITAL MAIN CBA UNIT SW A19 B19 A18 B18 A17 B17 A20 B20 C17 D17 E19 E20 D21 D22 C21 C22 F19 F20 D16 D15 L2 L1 M1 L3 M2 C1 A2 C4 B5 G1 G2 HDMI I/F J1 IF-AGC AB22 S-VIDEO-SW F2 F1 A12 B7 A8 A11 B12 D8 C12 A7 B8 VIDEO DECODER AUDIO DECODER AUDIO I/F DEMODULATOR /MPEG DECODER A/D CONVERTER IC3005 (DIGITAL SIGNAL PROCESS) DIGITAL SIGNAL PROCESS LVDS TX TP POL CPV OE STV W5,W7,AA4-AA8, AB3-AB8 N4,P2,P4,R1-R4,T2, T4,U4,V1,V4,W1-W3 AA17 AB17 AA16 AB16 AA15 AB15 AA13 AB13 AA12 AB12 AA11 AB11 AA14 AB14 AB19 Y19 AA18 AB20 AA19 SD-DQ(0-15) IC3002 (DDR2 SDRAM) CN3005 23 22 21 20 19 18 13 12 11 10 9 8 16 15 6 5 4 3 1 AUDIO SIGNAL M2,M3,M7,M8, SD-A(0-12) N2,N3,N7,N8, P2,P3,P7,P8,R2 B1,B9,C2,C8, D1,D3,D7,D9, F1,F9,G2,G8, H1,H3,H7,H9 VIDEO SIGNAL LLV0(+) LLV0(-) LLV1(+) LLV1(-) LLV2(+) LLV2(-) LLV3(+) LLV3(-) LLV4(+) LLV4(-) LLV5(+) LLV5(-) LLVCLK(+) LLVCLK(-) TP POL CPV OE1 STV LCD MODULE ASSEMBLY 4. Digital Signal Process Block Diagram FL11.11BLD TO SYSTEM CONTROL BLOCK DIAGRAM (CN201) TO POWER SUPPLY BLOCK DIAGRAM (CN602) 10 11 12 2 Q1931 10-5 CN1001 PROTECT3 BACKLIGHT-SW BACKLIGHT-ADJ VCOM COLD HOT Q1932 Q1930 SWITCHING CN1900 2 ACL 1 HOT-GND 11 3 15 8 Q1971 3 4 IC1931 2 3 2 1 Q1970 1 4 IC1930 14 7 5 4 10 2 T1950 INVERTER CBA HOT CIRCUIT. BE CAREFUL. Q1621 Q1004, Q1005 SW Q1800,Q1815 SW+16V INV+16V Q1972 NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. Q1600 2 1 15 16 3 4 DCT 12 VCC Q1001 8 11 6 5 1 3 6 5 2 3 7 1 OVER VOLTAGE PROTECTOR OVER VOLTAGE PROTECTOR Q1061 OVER VOLTAGE PROTECTOR Q1111 OVER VOLTAGE PROTECTOR Q1060 OVER VOLTAGE PROTECTOR Q1110 9 10 Q1161 OVER VOLTAGE PROTECTOR Q1211 8 Q1160 OVER VOLTAGE PROTECTOR Q1210 8 7 6 5 8 7 6 5 2 4 T1200 1 3 2 4 T1150 1 3 14 CURRENT CONTROL SWITCH Q1550 CURRENT CONTROL SWITCH Q1500 8 7 6 5 OVER VOLTAGE PROTECTOR Q1003 DRIVE Q1551, Q1552, Q1553 DRIVE Q1501, Q1502, Q1503 2 4 T1100 1 3 8 7 13 12 IC1700 (COMPARATOR) 5 6 OSC PWM CONTROL LOGIC IC1000 (PWM CONTROL) Q1801,Q1802, Q1803,Q1804 SW+16V T1050 2 4 CN1003 10 CN1200 1 2 CN1150 1 2 CN1100 1 2 CN1050 1 2 LCD MODULE ASSEMBLY VCOM BACK LIGHT BACK LIGHT BACK LIGHT BACK LIGHT 5. Inverter Block Diagram FL11.11BLINV TO INVERTER BLOCK DIAGRAM (CN1900) AC601 AC CORD LINE FILTER LINE FILTER 10-6 BRIDGE RECTIFIER D601- D604 POWER SUPPLY CBA Q602 SWITCHING CONTROL L602 L601 Q601 SWITCHING CN602 2 ACL 1 HOT-GND 4A/125V F601 4A/125V HOT CIRCUIT. BE CAREFUL. FEED BACK Q631 19 15 16 13 18 17 12 14 11 COLD 2 3 HOT 1 4 IC601 9 8 7 5 4 3 T601 CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. Q635 +5V REG. 4A/125V Q634 Q903,D905 SW+3.3V Q904,D906 SW+3.3V 3 2 Q640 SW+5V Q638,Q639 SWITCHING Q901,Q902 SWITCHING IC631 +3.3V REG. Q209,D204 SW+16V Q501 SW+16V Q207,Q208 SWITCHING Q210 SW+24.5V Q201,Q202, Q212 SW Q641,643 SW+5V Q637,D666 SW+3.3V IC901 +1.2V REG. Q642 SW+9V Q401 Q211 SW-8V CN901 1 9 6~8 10 11,12 4,5 CN301 10 16 21,22 19,20 13,14 CN201 13 8,9 2 10 12 CN3002 10 16 21,22 19,20 13,14 CN401 AL+3.3V 1 9 DVD-ON+3.3V EV+3.3V 6~8 DVD-ON+5V 10 11,12 EV+9V 4,5 EV+1.2V P-ON+3V P-ON+7V AL+3.3V P-ON+3.3V P-ON+5V CN1001 13 8,9 2 10 12 DVD-MAIN-PWR P-ON-H1 P-ON-H2 PROTECT1 PROTECT2 DVD MAIN CBA UNIT DIGITAL MAIN CBA UNIT INVERTER CBA TO SYSTEM CONTROL BLOCK DIAGRAM P-ON+9V AL+33V P-ON+5V AL+13V TUNER+5V AL+3.3V AL+3.5V DVD-ON+3.3V EV+3.3V DVD-ON+5V EV+9V EV+1.2V P-ON+3V P-ON+7V AL+3.3V P-ON+3.3V P-ON+5V LCD-8V LCD+16V INV+16V VGH P-ON+3.3V NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. LCD-8V LCD+16V INV+16V VGH P-ON+3.3V CAUTION ! : For continued protection against risk of fire, replace only with same type 4 A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V. 6. Power Supply Block Diagram FL11.11BLP 10-7 DISC-IN CN301 SP(+) 1 SP(-) 2 LOAD-DISC 6 GND 3 SL(-) 4 SL(+) 5 TS(+) TS(-) FS(+) FS(-) CN5001 CN801 1 LED-POWER 1 2 DVD-DISC-OUT 2 3 DVD-DISC-IN 3 DISC-OUT SENSOR CBA M SLED MOTOR M SPINDLE MOTOR LOAD-DISC DRIVE CBA TO DVD DIGITAL SIGNAL PROCESS BLOCK DIAGRAM Q804 +3.3V 1 NOTE: Either IC461 or IC462 is used for DVD MAIN CBA UNIT. - 17 18 12 11 SLED MOTOR DRIVE + SPINDLE MOTOR DRIVE - + - + - + TRACKING ACTUATOR DRIVE FOCUS ACTUATOR DRIVE - + - + - 23 6 4 5 3 1 2 25 24 27 26 VREF RESET 3 IC462 + 1 +3.3V 14 13 15 16 RESET 1 IC461 IC301 (SERVO DRIVE) 2 +3.3V 5 6 3 2 IC202 (OP AMP) 7 1 61 DVD-DISC-OUT 63 DVD-DISC-IN DVD-SCLK DVD-CS DVD-SDATA DVD-REMOTE DVD-P-ON 65 LOAD-DISC 121 SP-ROT 122 SL-ADS 67 SLD 66 SPDL 123 TD-OFST 126 TRACKING DRIVE 127 FOCUS DRIVE 124 FD-OFST 70 RESET 53 54 56 49 77 IC101 (MICRO CONTROLLER) DVD-SCLK DVD-CS DVD-SDATA DVD-REMOTE DVD-P-ON LED-CONT DVD-DISC-OUT DVD-DISC-IN TO SYSTEM CONTROL BLOCK DIAGRAM DVD MAIN CBA UNIT 7. DVD System Control / Servo Block Diagram FL11.11BLSD FS PICKUP TS DETECTOR FS(+) FS(-) TS(+) TS(-) CD-LD DVD-LD PD-MONI GND(DVD-PD) GND(CD-PD) GND(LD) C D A B CD/DVD ~ ~ 13 42 53 ~ CN201 2 3 1 4 CD 4 1 3 6 FS(+) FS(-) TS(+) TS(-) IC201 (SW) DVD Q253,Q254 CN201 10 AMP 8 AMP Q251,Q252 7 6 5 9 159 DATA RAM INST. ROM INTERRUPT CONTROLLER RF SIGNAL PROCESS CIRCUIT 62 CD/DVD 106 104 105 103 99 100 98 97 115 116 113 114 178 SDRAM DATA(0-15) TO DVD SYSTEM CONTROL / SERVO BLOCK DIAGRAM SDRAM DATA(0-15) CN201 16 18 17 15 19 ~ ~ ~ SDRAM TIMER ECC CPU I/F BCU DMA DECODER I/F STREAM I/F CPU I/F DVD MAIN CBA UNIT BCU DEBUG 21~30 34~42 212 READ MEMORY UMAC 1~4 7~14 17~18 215 216 WATCH DOG TIMER 32BIT CPU DVD/CD FORMATTER IC101 (MICRO CONTROLLER) 22 194 26 SDRAM ADDRESS(0-10) SDRAM ADDRESS(0-10) 29 209 34 EXTERNAL MEMORY I/F 2 INST CACHE VIDEO I/F AUDIO I/F INST. ROM DATA RAM INST. ROM DATA RAM DATA CACHE 32BIT CPU REMOTE CONTROL WATCH DOG TIMER TIMER INTERRUPT CONTROLLER GENERAL I/O SERIAL I/O PROCESSOR DSP DECODER NTSC/PAL ENCODER AUDIO D/A CONVERTER 29 36 38 45 TO VIDEO BLOCK DIAGRAM TO SYSTEM CONTROL BLOCK DIAGRAM TO AUDIO BLOCK DIAGRAM AUDIO SIGNAL FLASH ROM IC103 (FLASH ROM) DVD-Pr DVD-Pb DVD-Y FDQ (0-15) 129 130 131 FADR (0-19) Pr Pb Y DVDAUDIO-MUTE DVD-AUDIO(R) DVD-AUDIO(L) DVD-SPDIF 1 9 16 25 48 D/A D/A D/A 151 146 144 152 ~ ~ ~ 10-8 ~ IC503 (SDRAM) VIDEO SIGNAL 8. DVD Digital Signal Process Block Diagram FL11.11BLDD SCHEMATIC DIAGRAMS / CBA AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by the mark “#” in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards. Notes: 1. Do not use the part number shown on these drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared. 2. All resistance values are indicated in ohms (K = 103, M = 106). 3. Resistor wattages are 1/4W or 1/6W unless otherwise specified. 4. All capacitance values are indicated in µF (P = 10-6 µF). 5. All voltages are DC voltages unless otherwise specified. 6. This schematic diagrams are masterized version that should cover the entire FL11.11 chassis models. Thus some parts in detail illustrated on this schematic diagrams may vary depend on the model within the FL11.11 chassis. Please refer to the parts lists for each models. 7. The Circuit Board layout illustrated on this service manual is the latest version for this chassis at the moment of making this service manual. Depend on the mass production date of each model, the actual layout of each Board may differ slightly from this version. 11-1 FL11.11SC LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V. 2. CAUTION: Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. 3. Note: 1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since the drawings were prepared. 2. To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list section of the service manual. 4. Voltage indications on the schematics are as shown below: Plug the TV power cord into a standard AC outlet.: Unit: Volts Unit: Volts 1 2 5.0 The same voltage for both TV & DVD modes 3 5.0 <0> TV mode DVD mode Indicates that the voltage is not consistent here. 5. How to read converged lines 1-D3 Distinction Area Line Number (1 to 3 digits) 3 AREA D3 2 Examples: 1. "1-D3" means that line number "1" goes to the line number "1" of the area "D3". 1 2. "1-B1" means that line number "1" goes to the line number "1" of the area "B1". 1-B1 AREA B1 1-D3 A B C D 6. Test Point Information : Indicates a test point with a jumper wire across a hole in the PCB. : Used to indicate a test point with a component lead on foil side. : Used to indicate a test point with no test pin. : Used to indicate a test point with a test pin. The reference number of parts on Schematic Diagrams/CBA can be retrieved by application search function. 11-2 FL11.11SC Power Supply 1 Schematic Diagram CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. CAUTION ! : For continued protection against risk of fire, replace only with same type 4 A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V. 4A/125V AUDIO SIGNAL CONTINUE POWER 4 INV+16V LCD+16V P-ON+3.3V LCD-8V LCD+24.5V CONTINUE POWER 4 AUDIO(R)-OUT AUDIO(L)-OUT CONTINUE POWER 2 AMP(R)-OUT AMP(L)-OUT HOT CIRCUIT. BE CAREFUL. F601 4A/125V AC601 AC CORD 19.4 R601 560K/1/2W CN601 AC120V 2 AC120V 1 L601 LINE FILTER D602 1N5406-BP L602 LINE FILTER D601 1N5406-BP R603 OPEN C691 1000P/250V R602 1.8/5W C692 OPEN D604 1N5406-BP C604 OPEN WITH DVD D634 SB240-B/P 11 3 C605 680 /200V 14 D633 FR151-B/P 12 4 BC601 BEAD 5 18 7 13 16 8 15 Q601 TK5A50D 134.5 D (SWITCHING) G 5.3 0.1 S C610 5.3 OPEN 0.5 D611 R613 1.2K Q602 2SC2120-O SWITCHING CONTROL C611 470P /2KV D640 OPEN 19 D641 SB390 D642 SB390 IC601 LTV817MCF ERROR VOLTAGE DET R616 180 R645 270 14.3 JS631 4 0.5 2 3 5.7 D609 R650 6.8K R615 2.7K C612 0.082 /100V D653 OPEN IC631 LD1117V (+3.3V REG.) C641 OPEN 6.9 5.1 R695 33 5.8 R666 1 R667 WIRE D637 SB160 R652 24K R653 WIRE -8.6 R238 150 R239 OPEN R696 3.3/1W R697 3.3/1W Q210 KTC3198-Y-AT/P (SW+24.5V) 30.2 24.4 25.1 D411 C682 0.1 6.7 Q635 KTC3198-Y-AT/P (+5V REG.) R698 OPEN R684 OPEN 6.8 0.7 R661 390 /1/2W C223 22/50V D418 3V9BSB-T26 D676 WIRE C684 0.1 R401 22K D413 D666 KIA431-AT/P R402 22K C681 0.1 R680 6.8K D401 OPEN R675 10K R676 100K C676 2.2/50V R681 OPEN D665 WIRE D667 OPEN D419 R408 10K D657 33BSB-T26 R687 10 D420 D409 D412 12.7 R689 1.2K 9.7 R688 10 D670 10BSB-T26 D671 WIRE 9.0 Q642 KTC3198-Y-AT/P (SW+9V) C656 100/16V D410 C657 22/50V R692 R694 2.7 WIRE 6.8 R691 R693 2.7 WIRE R682 2.7 R683 2.7 R406 OPEN 6.7 6.0 R647 OPEN D664 4V7BSB-T26 R649 OPEN 5.3 Q640 2SC2120-Y (SW+5V) 6.0 6.8 C653 220/10V R685 22 R686 1K C643 OPEN C655 OPEN 5.3 Q643 2SC2120-Y (SW+5V) 5.3 Q641 2SC2120-Y 6.0 (SW+5V) R641 1.1K C654 220/10V R642 10K D645 KIA431B-AT/P R643 10K TO DIGITAL MAIN CBA UNIT CN3002 P-ON-H2 AUDIO(L)-OUT GND AUDIO(R)-OUT PROTECT3 AMP(L)-OUT GND AMP(R)-OUT P-ON-H1 P-ON+3V PROTECT1 GND P-ON+5V P-ON+5V PROTECT2 P-ON+7V GND GND P-ON+3.3V P-ON+3.3V AL+3.3V AL+3.3V GND OE2 REMOTE BACKLIGHT-SW LED1 BACKLIGHT-ADJ VCOM-PWM CONTINUE POWER 4 PROTECT3 BACKLIGHT-SW BACKLIGHT-ADJ VCOM-PWM OE2 P-ON-H1 LCD-P-SAFETY CONTINUE POWER 4 LED1 REMOTE P-ON+9V AL+3.3V AL+6V CONTINUE POWER 2 AL+3.3V M+13V D+5.5V P-ON+5V AL+13V P-ON+9V PROTECT2 LCD+16V PROTECT1 CONTINUE POWER 3 P-ON+3.3V P-ON+9V P-ON+5V RESET CONTINUE POWER 2 AL+33V TUNER+5V CN301 3.3 1 2.6 2 0 3 2.6 4 3.3 5 2.6 6 0 7 2.6 8 3.2 9 3.1 10 2.5 11 0 12 5.3 13 5.3 14 0 15 6.9 16 0 17 0 18 3.4 19 3.4 20 3.4 21 3.3 22 0 23 0.6 24 3.3 25 3.2 26 0.6 27 0.9 28 0.8 29 R659 100K R407 22K Q644 OPEN D421 R679 3.6K R658 10K C647 R660 1/50V WIRE R663 1.8K R664 1.8K D659 6V8BSA-T26 D662 FR154 D661 FR154 D407 10BSB-T26 D417 3V9BSB-T26 R236 33 D205 30BSD-T26 D206 4.1 Q637 2SC4881F 3.4 (SW+3.3V) R678 C651 10 OPEN R677 270 Q639 KTC3198 -Y-AT/P (SWITCHING) 0 D673 OPEN C648 100/10V COLD D207 R674 1K 0.2 0 Q634 KTC3198-Y-AT/P (SWITCHING) D658 3V3BSB-T26 R665 WIRE R662 15 33.8 0.2 R669 1K HOT R235 270 R241 22K Q633 OPEN R668 620 D674 OPEN 6.1 Q638 KTA1267-GR-AT/P (SWITCHING) R673 22K R639 1.5K R637 1.2K R638 1.5K 0 D660 R636 2.7/1/2W 1 D650 D651 OPEN 6.2 1 2 3 2.1 3.4 5.1 -8.6 R237 8.2K D648 SB140 R644 820 R648 1K D652 5V6BSB-T26 Q636 2SA950-O (+3.3V REG.) 5.1 VIN D610 OPEN VOUT D608 OPEN GND D612 39BSB-T26 C683 0.1 D210 8V2BSB-T26 D414 R672 WIRE 6.3 Q631 KTC3198-Y-AT/P (FEED BACK) R690 OPEN 5.1 C646 2200P/100V 32.5 R654 1K C652 1000/6.3V D209 39BSB-T26 D649 32.5 R412 10K R404 22K R244 C224 10/50V OPEN C640 OPEN 1 C613 1200P /100V Q211 KTC3198 -Y-AT/P (SW-8V) -7.9 R242 12K C650 OPEN R646 180 33.6 2 R614 0.39 /2W R670 WIRE R671 WIRE C639 1000/35V D607 4V3BSB-T26 0 D606 27BSB-T26 9 C609 0.027 R611 R610 /100V 150 150 0 R240 D208 47K 33.7 Q207 33.1 KTA1267-GR-AT/P (SWITCHING) R223 R224 3.3k 27K R225 0.1 22K 0.7 Q208 R226 0 KTC3198-Y-AT/P 22K (SWITCHING) D655 1N4005 C645 2200/6.3V R405 47K R403 47K R243 27 33.8 C632 220/25V R234 2.2K 3.1 -3.9 Q402 KTC3198-Y-AT/P (RESET) R409 OPEN D647 SB240-B/P -0.7 Q401 KTC3198 -Y-AT/P (SWITCHING) 0 D204 KIA431-AT/P R699 56 C225 OPEN D406 15BSB-T26 D405 D402 OPEN C633 2200/6.3V D632 FR104-B 17 R245 8.2K 2.5 R231 C221 1.5K 0.01 D211 D403 OPEN D416 R411 33K D639 1ZB43BB C634 1000/10V R232 11K R233 910 D203 C402 OPEN C638 220/50V C222 470/25V R410 15K D638 FR154 T601 POWER TRANS 3 C644 3300 /16V D643 D644 FR104-B 10BSB-T26 C642 1/50V C637 2200P/1KV C694 OPEN R604 390K R605 390K R606 390K R618 390K R228 2.7K D646 SB360BH R651 1 TO INVERTER CBA CN1900 16.4 C501 100/25V D404 15.8 Q209 2SD400 (SW+16V) R229 2.7K D603 1N5406-BP C603 OPEN 15.8 Q501 2SC2120-Y (SW+16V) 16.4 R247 R227 3.3/2W 2.7/1W D635 24BSB-T26 C693 1000P/250V JS603 OPEN JS604 OPEN JS601 OPEN JS602 OPEN C602 0.47/300V CN602 ACL 2 HOT-GND 1 19.4 R617 1.8/5W C601 0.47/300V AC CORD C631 1000/25V R501 10 R607 OPEN SA601 SURGE ABSORBER 4 D631 FR154 4A 125V D415 POWER SUPPLY CBA UNLESS OTHERWISE SPECIFIED: DIODES ARE 1SS133. A B C D 11-3 E F FL11.11SCP1 Power Supply 2 Schematic Diagram *Either TU301 is used for Power Supply CBA. 3 R303 R302 SCL SDA IF-AGC DIF-OUT2 DIF-OUT1 AUDIO-MUTE BC301 WIRE L301 OPEN JS304 WIRE C310 47P C311 47P CONTINUE POWER 1 AL+3.3V M+13V D+5.5V P-ON+5V AL+13V P-ON+9V PROTECT2 LCD+16V PROTECT1 CONTINUE POWER 4 KEY-IN2 DVD-LED SP802 SPEAKER R-CH 1 2 3 4 5 6 7 8 9 10 11 0 0 R306 R307 R301 OPEN D302 OPEN D301 C307 OPEN OPEN 0 0 1 2 3 0 1.3 4.0 JS303 D904 FR104-B R305 OPEN 5.1 R918 10K 5.0 4.3 R914 2.7 /1/2W JS301 OPEN R311 OPEN C306 1/50V C304 OPEN C305 0.1 C302 0.1 R310 0 R309 82 R308 82 R304 OPEN C301 OPEN C303 330 /10V D303 OPEN R916 10K R925 3.9 4.6 R924 3.9 4.1 R922 22 R923 220 R819 22K C846 470P C823 1000/25V D804 20BSB-T26 D803 20BSB-T26 C821 0.1 BC801 BEAD C817 1 C816 10/50V C815 R810 0 1 C836 R815 1 10K C837 2700P R816 3.3K BC804 BEAD C830 0.47 C828 0.1 3.4 Q903 2SC2120-Y (SW+3.3V) R929 1.2 5.0 R928 180 4.1 R927 10 C822 1000P L804 33uH L803 33uH C820 1 R926 470 C918 100/10V C825 0.1 R811 OPEN C832 3.3/50V C826 1000P C915 OPEN R909 WIRE RAMP GENERATOR DRIVE2 C818 0.1 C909 OPEN D408 OPEN D908 OPEN C819 10/50V L951 WIRE C952 0.1 CLOCK CONTROL C951 100/10V DRIVE1 R960 12K C960 220P MUTE CONTROL GND GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 3.6 3.6 5.0 2.1 3.6 18.0 12.9 12.9 6.1 6.1 0 0 6.1 6.1 12.9 12.9 18.1 R803 11K R804 11K C801 1 R814 3.3K R802 27K C802 0.1 L802 33uH L801 33uH C804 0.1 C827 10/50V C806 1 C803 1 C805 1000P C807 0.1 C811 0.47 R805 OPEN C808 1000P BC803 BEAD CN801 SP(L)- 1 SP(L)+ 2 C839 470P D801 20BSB-T26 D802 20BSB-T26 H BC802 BEAD 19 20 0 7.1 NU 22 R817 100K R808 OPEN R806 4.7K C813 OPEN R820 22K 7.0 IC951 NJM4558M(TE1) (OP AMP) R809 OPEN 7.0 GND 1 2 3 4 4.6 0 4.5 0 R959 12K C959 220P R901 91 C847 0.1 C810 0.1 R902 91 R903 91 R953 100K C953 1 R954 100K R957 39K C957 2.2 WF10 R955 100K R951 100 0 R906 100 R952 100 9.0 4.5 4.5 4.5 8 7 6 5 VCC R818 10K Q802 0.1 KTC3198 -Y-AT/P 0 (AUDIO-MUTE) 0 Q801 KTC3198 -Y-AT/P D806 (AUDIO-MUTE) 1SS133 C814 OPEN C809 0.1 NU 21 C905 L901 OPEN WIRE R958 39K C958 2.2 POWER LIMIT C838 470P R930 OPEN PROTECTIONS & LOGIC PWM1 C835 2700P C908 OPEN Q905 OPEN C833 0.1 R812 OPEN C824 1 IC801 BD5426EFS-E2 (AUDIO AMP) C834 R813 1 10K D901 1N4005 D902 1N4005 R931 OPEN C955 OPEN C901 OPEN WF9 C902 OPEN WF8 C903 OPEN R904 1.3K R908 C954 OPEN 1 R956 C956 100K OPEN CN901 3.4 1 3.3 2 3.4 3 1.3 4 1.3 5 3.4 6 3.4 7 3.4 8 3.4 9 5.3 10 9.7 11 9.7 12 0 13 0 14 0 15 0 16 0 17 0 18 0 19 0.5 2.5 3.4 2.5 2.8 0.5 D906 3V9BSB-T26 D903 1N4005 3.6 0 3.6 4.1 13.0 18.1 12.9 12.9 6.1 6.1 0 0 6.1 6.1 12.9 12.9 18.0 8.8 5.1 5.4 0 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 GND GND PWM2 G D907 1SS133 R921 10K 3.4 Q904 KTC3198-Y-AT/P (SW+3.3V) D909 1N4005 D807 OPEN CL801 C911 OPEN C914 OPEN C917 220/6.3V R919 150 R920 3.3K C829 0.1 2 1 C910 OPEN BC805 BEAD CN802 SP(R)- 1 SP(R)+ 2 CONTINUE POWER 1 AMP(R)-OUT AMP(L)-OUT C912 OPEN R913 3.3 /1/2W D905 KIA431-AT/P C919 47/25V CL802 C916 1000/6.3V R917 390 0.1 0.8 Q902 KTC3198 0 -Y-AT/P (SWITCHING) R915 10K C309 0.47 C913 OPEN R910 0.3 R912 1K JS302 C308 OPEN L302 0.22uH L303 0.22uH C845 470P SP801 SPEAKER L-CH R911 0.3 VIN 9 10 11 12 13 14 15 16 17 18 19 VOUT 1 2 3 4 5 6 7 8 GND NU NU NU SCL SDA +32V +5V NU IF-AGC DIF-OUT2 DIF-OUT1 IC901 KIA1117API00/T0-220 (+1.2V REG.) Q901 2SA950-O (SWITCHING) CONTINUE POWER 3 4 TUNER UNIT SCL NU NU DIF-OUT2 DIF-OUT1 IF-AGC VCC NU NU NU NU CONTINUE POWER 1 AL+33V TUNER+5V *TU301 TUNER UNIT NU NU NU VCC NU +32V GND SDA *TU301 WF11 C907 2200P R905 1.3K R907 C906 OPEN 2200P C904 OPEN WF12 20 21 22 23 24 25 26 CN303 0 1 3.4 2 0.6 3 4 3.2 5 0 6 2.8 7 2.5 8 3.4 9 0 10 2.5 11 0 12 2.5 13 0 14 3.4 15 3.3 16 0 17 0.9 18 0 19 0.9 20 0 21 0.6 22 0 23 4.6 24 0.2 25 4.6 26 0 27 1.7 28 0 29 CN902 0.9 1 0 2 0.9 3 0 4 0.6 5 0 6 0 1.6 0.2 1.6 0 1.7 7 8 9 10 11 12 13 TO DVD MAIN CBA UNIT CN401 AL+3.3V LED-CONT DVD-DISC-OUT EV+1.2V EV+1.2V EV+3.3V EV+3.3V EV+3.3V DVD-ON+3.3V DVD-ON+5V EV+9V EV+9V GND GND GND GND GND GND GND PWRCON(NU) DVD-SCLK DVD-CS DVD-DISC-IN DVD-SDATA DVD-REMOTE DVD-P-ON TO DIGITAL MAIN CBA UNIT CN3003 GND KEY-IN2 DVD-LED P-ON-H3(NU) DVD-MAIN-PWR DVD-P-ON DVD-REMOTE DVD-SDATA DVD-DISC-IN GND DVD-CS GND DVD-SCLK GND DVD-DISC-OUT LED-CONT GND DVD-Pr GND DVD-Pb GND DVD-Y GND DVD-AUDIO(L) DVD-AUDIO-MUTE DVD-AUDIO(R) GND DVD-SPDIF GND TO DVD MAIN CBA UNIT CN601 DVD-Pr GND DVD-Pb GND DVD-Y GND GND GND DVD-AUDIO(L) DVD-AUDIO-MUTE DVD-AUDIO(R) GND DVD-SPDIF WF13 POWER SUPPLY CBA I J 11-4 K L FL11.11SCP2 Power Supply 3 & Jack Schematic Diagram POWER SUPPLY CBA BC841 BEAD R847 4.7K 5.3 4 2.6 Q841 KTC3198-Y-AT/P (BUFFER) 2.0 JK841 DIGITAL AUDIO-OUT (COAXIAL) R844 220 C841 1 R843 110 R841 OPEN C843 0.01 C842 1 C844 10/50V R848 4.7K R845 OPEN R778 100K R713 OPEN R711 OPEN R712 OPEN 3 HDMIAUDIO(L)-IN HDMIAUDIO(R)-IN C702 OPEN R779 100K R792 OPEN R793 OPEN R794 OPEN R795 OPEN R725 39K C721 OPEN C724 2.2 R726 39K C722 OPEN R772 10K 0 1 0.2 2 VDD 16 9.0 15 0.2 4.5 3 4.5 4 14 0.2 13 4.5 0.2 5 0 6 INH 0 7 VEE 12 0 11 4.5 0 8 GND C723 2.2 R724 15K R722 OPEN C776 100P IC771 TC4052BF(ELNF) (AUDIO SELECTOR) R791 OPEN C704 OPEN R716 OPEN R721 OPEN JK722 R790 OPEN C703 OPEN R723 15K JK721 R789 OPEN C701 OPEN R715 OPEN R714 OPEN JK711 PC-AUDIO-IN R788 OPEN SW CTL R773 10K COMPONENTAUDIO(R)-IN R741 OPEN R745 39K C741 OPEN C744 2.2 R746 39K C742 OPEN R744 15K JK742 R742 OPEN C773 OPEN R783 OPEN C771 100/16V C772 0.1 R771 WIRE CONTINUE POWER 4 KEY-IN1 AUDIO-MUTE R784 OPEN 10 9.0 9 9.0 0 9.0 0 R785 OPEN R786 OPEN R787 OPEN R777 100K C775 100P R774 10K 0 Q771 KTC3198-Y-AT/P (INVERTER) R775 10K 0 Q772 KTC3198-Y-AT/P (INVERTER) WF1 R734 10 JK731 COMPONENT -Y-IN WF3 R731 75 C731 39P R735 10 JK732 2 R782 OPEN R763 10K C743 2.2 R743 15K JK741 R781 10K OPEN R776 100K 9.0 COMPONENTAUDIO(L)-IN R780 OPEN COMPONENT -Pb-IN C732 39P CONTINUE POWER 1 P-ON+3.3V P-ON+9V P-ON+5V RESET WF2 R732 75 R736 10 JK733 COMPONENT -Pr-IN C733 39P WF7 WF4 WF5 R733 75 WF6 JK751 S-VIDEO-IN C Y SW C751 100P R756 0 C754 0 R757 0 C755 0 R752 75 C752 100P R758 0 JK752 1 VIDEO-IN C753 100P R759 15K R754 OPEN R760 15K R761 39K C761 OPEN JK754 R755 OPEN R762 39K C762 OPEN AUDIO(R)-IN C756 0 R753 75 JK753 AUDIO(L)-IN CL701B 1 2 3 4 5 6 7 8 9 R751 75 S-VIDEO-Y-IN S-VIDEO-SW S-VIDEO-C-IN GND VIDEO-IN GND AUDIO(L)-IN GND AUDIO(R)-IN CL701A 1 2 3 4 5 6 7 8 9 CN302 0 1 1.7 2 0 3 0 4 3.4 5 0 6 0 7 0 8 0 9 0 10 4.5 11 0 12 4.5 13 0 14 0 15 0 16 0 17 0 18 0 19 0 20 0 21 3.3 22 3.3 23 0 24 0 25 1.0 26 0 27 0.2 28 3.3 29 TO DIGITAL MAIN CBA UNIT CN3006 GND SPDIF GND VIDEO-IN S-VIDEO-SW S-VIDEO-C-IN GND S-VIDEO-Y-IN GND INPUT1 AUDIO(R) INPUT0 AUDIO(L) GND COM-VIDEO-Y-IN GND COM-VIDEO-Pb-IN GND COM-VIDEO-Pr-IN AUDIO-MUTE SDA SCL RESET IF-AGC GND DIF-OUT1 GND DIF-OUT2 KEY-IN1 CONTINUE POWER 2 SCL SDA IF-AGC DIF-OUT2 DIF-OUT1 AUDIO-MUTE C757 2.2 C758 2.2 JACK CBA M N O P 11-5 Q R FL11.11SCP3 Power Supply 4 Schematic Diagram CONTINUE POWER 1 INV+16V LCD+16V P-ON+3.3V LCD-8V LCD+24.5V POWER SUPPLY CBA 4 R210 10 C201 0.1 C216 1000P TO INVERTER CBA CN1001 3 GND INV+16V GND BACKLIGHT-ADJ BACKLIGHT-SW PROTECT3 GND LCD+16V LCD+16V VGH GND P-ON+3.3V LCD-8V VCOM GND CN201 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 6.8 R208 1 6.8 JS201 OPEN 6.9 Q204 KTA1267-GR-AT/P 0 (V-COM DRIVE) R212 10 R215 OPEN IC201 TL3472CDR (COMPARATOR) 15.87.1 6.8 6.8 8 7 6 5 VCC C203 0.1 C218 1 C213 OPEN R222 OPEN C220 OPEN 0 R220 1K 0.3 Q205 KTC3198-Y-AT/P (V-COM DRIVE) R821 OPEN R203 OPEN 22.0 C209 OPEN R205 OPEN R204 390 JS202 CONTINUE POWER 1 LED1 REMOTE P-ON+9V AL+3.3V AL+6V 3.4 24.4 Q201 KTA11267-GR-AT/P 23.9 (SWITCHING) Q202 KTC3198-Y-AT/P 19.1 (SWITCHING) R206 1K 0.4 R207 0 100K C215 OPEN R219 15K R216 10K 5.9 C202 0.1 C214 OPEN Q206 OPEN C219 47/25V R202 1K C206 OPEN D202 1SS133 R249 OPEN C204 2.2/50V -1.5 0.6 1.2 0.6 C207 0.1 JS101 CONTINUE POWER 2 KEY-IN2 DVD-LED S R871 560 C873 2.2 IC871 NJM4558M(TE1) (OP AMP) Q171 KTC3198-Y-AT/P 0 (SWITCHING) 0.7 0 T C871 3300P C880 100/16V R877 1K R880 16K C885 2.2 OPEN R171 22K JK871 R873 100K R892 20K C876 100P R174 OPEN R893 22K CONTINUE POWER 3 KEY-IN1 AUDIO-MUTE R874 100K C872 3300P R891 20K C875 100P Q872 KTC3198-Y-AT/P (AUDIO-MUTE) C883 2.2 R884 100K C878 6800P CONTINUE POWER 1 AUDIO(R)-OUT AUDIO(L)-OUT C882 2.2 R883 100K AUDIO(R) -OUT 0 -1.6 0 R886 100K R885 100K Q871 KTC3198-Y-AT/P (AUDIO-MUTE) JK872 R882 100 9.0 4.5 4.5 4.5 8 7 6 5 VCC GND 1 2 3 4 4.5 4.5 4.5 0 R872 560 R878 1K AUDIO(L) -OUT 0 -1.5 0 R881 100 R175 22K Q873 KTC3198-Y-AT/P (SWITCHING) 0.1 Q212 KTC3198-Y-AT/P (SWITCHING) C874 2.2 R172 22K 3.4 0 JS102 OPEN R173 Q874 KTA1267 -GR-AT/P (MUTE DRIVE) R248 10K C879 0.1 CN101 1 2 3 4 5 6 7 8 R887 22K R888 1K 3.4 R201 100K L871 WIRE Q172 KTC3198-Y-AT/P 2.0 (SWITCHING) 0 0 1 C212 OPEN R221 OPEN VEE 1 2 3 4 0.2 0.2 0 0 D675 WIRE C208 OPEN TO IR SENSOR CBA CL101B GND REMOTE AL+3.3V LED1 P-ON-H1 KEY-IN1 KEY-IN2 DVD-LED C210 22/25V R217 1.5K C675 OPEN 2 R218 10K 15.8 6.9 Q203 KTC3198-Y-AT/P (V-COM DRIVE) R213 100K C217 0.1 CONTINUE POWER 1 PROTECT3 BACKLIGHT-SW BACKLIGHT-ADJ VCOM-PWM OE2 P-ON-H1 LCD-P-SAFETY C877 6800P R879 16K C884 2.2 U V 11-6 W X FL11.11SCP4 Inverter Schematic Diagram NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. HOT CIRCUIT. BE CAREFUL. INVERTER CBA 2 C1910 270 /200V 4 BC1301 WIRE T1950 POWER TRANS TO POWER SUPPLY CN1900 CBA CN602 ACL 2 HOT-GND 1 R1940 220K C1940 OPEN R1946 OPEN R1943 330K R1941 220K R1944 330K R1942 120K R1989 330K 10 R1947 R1948 OPEN OPEN 3 11 D1990 31DF4-FC D1940 OPEN C1932 0.027 /100V R1934 180 R1933 82 R1932 82 14 8 R1936 180 R1935 1.5K D1932 Q1970 KTC3200-GR-AT/P 81.0 (SWITCHING) 6.3 5.8 82.0 4 0.4 R1982 2.7K 3 0.2 1.1 1 4 0 0 2 3 R1800 10K 0.2 C1905 2200P/250V R1630 10K D1630 C1906 OPEN D1935 OPEN C1933 0.1 /100V R1631 3.3K R1939 2.2K C1800 100/25V D1802 WIRE HOT 2 TO POWER SUPPLY CBA CN201 GND INV+16V GND BACKLIGHT-ADJ BACKLIGHT-SW PROTECT3 GND LCD+16V LCD+16V VGH GND P-ON+3.3V LCD-6.8V VCOM GND 1 TO LCD MODULE ASSEMBLY GND LCD+16V LCD+16V VGH GND P-ON+3.3V P-ON+3.3V LCD-6.8V GND VCOM GND Q1803 KTC3198 -Y-AT/P (SWITCHING) 0.7 COLD CN1001 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Q1804 KTC3198 -Y-AT/P (SWITCHING) 0.1 0.8 0 0.1 C1000 OPEN 0 R1554 2.2K 0 C1502 0.01 0.8 Q1802 0 KTC3198 R1808 -Y-AT/P 5.1K SWITCHING BACKLIGHT-ON C1001 0.1 Q1005 KTC3198 -Y-AT/P (SWITCHING) 0.2 R1035 3.3K CN1005 0 1 15.8 2 15.8 3 0 4 0 5 3.4 6 3.4 7 -6.2 8 0 9 0 10 0 11 CN1003 1 0 2 15.8 3 15.8 4 0 5 0 6 3.4 7 3.4 8 -6.2 9 0 10 0 11 0 TO LCD MODULE ASSEMBLY GND LCD+16V LCD+16V VGH GND P-ON+3.3V P-ON+3.3V LCD-6.8V GND VCOM GND R1036 10K R1034 10K 3.6 1.9 4.8 R1033 10K 0 0.1 Q1600 KTC3198 -Y-AT/P (SWITCHING) R1601 10K C1601 OPEN C1600 0.1 D1005 WIRE C1009 100/25V 0 Q1621 KTC3198 -Y-AT/P (SWITCHING) R1621 10K IC1000 TL494CDR PWM CONTROL R1025 OPEN R1015 7.5K R1620 100K 0 BC1550 BEAD 2 R1551 10 C1551 OPEN 3.9 S 3.9 Q1550 G 2SK2417 0.2 CURRENT CONTROL SWITCH R1550 D1550 12K 20BSB-T26 D1066 D1112 7 1 6 3 5 C1067 10/50V R1067 20k D1110 D1117 R1113 18K C1113 10/50V R1118 390 D1116 D1118 Q1110 KTC3198-Y-AT/P OVER VOLTAGE PROTECTOR 0.7 C1114 R1114 0.01 8.2K D1123 D1113 R1112 390 R1116 100K C1115 15P/6.3KV C1117 10/50V R1117 20k C1500 470P/2KV D1051 OPEN 4.0 3.9 3.9 4.0 Q1502 2SA950-O (DRIVE) C1501 OPEN R1500 12K D1162 0 D1500 20BSB-T26 2 8 4 7 1 6 3 5 R1165 27K R1161 20K D1160 D1167 C1166 1500P R1163 18K C1163 10/50V R1168 390 D1166 D1168 C1165 15P/6.3KV C1172 0.1 R1169 18K C1167 10/50V R1167 20k 0 R1171 27K Q1161 KTC3198-Y-AT/P OVER VOLTAGE PROTECTOR 0.7 C1168 R1170 0.01 8.2K D1170 D1172 R1172 1M D1165 0 D1169 D1174 R1166 100K 0 Q1160 KTC3198-Y-AT/P OVER VOLTAGE PROTECTOR 0.7 C1164 R1164 8.2K 0.01 D1173 D1163 R1162 390 BACK LIGHT D1121 0 D1164 D1161 T1150 INVERTER TRANS BC1501 BEAD S 3.9 Q1500 2SK2417 0.2 G CURRENT CONTROL R1501 10 SWITCH 15.5 C1162 1500P BC1500 BEAD 82.5 D Q1501 2SC2120-Y (DRIVE) R1051 OPEN CN1200 2 1 0 0 C1161 15P/6.3KV R1160 100K BACK LIGHT D1115 0 R1121 27K Q1111 KTC3198-Y-AT/P OVER VOLTAGE PROTECTOR 0.7 C1118 R1120 0.01 8.2K R1119 18K D1122 R1122 1M CN1150 2 1 0 D1119 D1124 D1120 BACK LIGHT D1071 0 R1115 27K R1111 20K CN1100 2 1 0 D1114 D1111 C1116 1500P Q1061 KTC3198-Y-AT/P OVER VOLTAGE PROTECTOR 0.7 C1068 R1070 0.01 8.2K R1069 18K D1072 R1072 1M D1065 R1071 27K D1074 C1065 15P/6.3KV BACK LIGHT 0 D1069 D1070 8 4 C1063 10/50V R1068 390 R1066 100K C1122 0.1 C1211 15P/6.3KV R1210 100K C1212 1500P C1006 0.1 C1010 OPEN R1016 120K R1017 10K R1031 15K R1022 2.2K C1013 0.1 C1012 3900P /100V R1028 36K D1171 0 0 3.6 3.6 0 0 1 6 3 5 R1081 5.6K R1032 24K D1223 D1213 R1212 390 D1217 C1216 1500P D1218 R1213 18K C1213 10/50V R1218 390 D1216 R1216 100K C1222 0.1 0 R1221 27K D1224 Q1211 KTC3198-Y-AT/P OVER VOLTAGE PROTECTOR 0.7 C1218 R1220 8.2K 0.01 D1220 R1219 18K R1217 20k D1215 0 D1219 C1215 15P/6.3KV D1222 R1222 1M Q1210 KTC3198-Y-AT/P OVER VOLTAGE PROTECTOR 0.7 C1214 R1214 8.2K 0.01 C1217 10/50V LCD MODULE ASSEMBLY D1221 0 0 R1020 OPEN R1027 OPEN D1004 WIRE 0.5 Q1001 KTC3198-Y-AT/P (SWITCHING) 7 R1211 20K D1210 R1023 3.3K R1026 220 Q1003 KTC3198-Y-AT/P (SWITCHING) 0 R1030 C1011 22K 0.1 4 R1215 27K D1214 D1211 C1205 OPEN R1080 22K D1212 T1200 INVERTER C1204TRANS OPEN 2 8 D1006 D1003 3.4 R1003 100K R1024 100K R1600 18K 3.4 0 5.1 Q1004 KTA1267 -GR-AT/P (SWITCHING) D1040 36BSB-T26 T1100 INVERTER TRANS 0.2 0.3 5.1 5.1 15.73.7 0 0 16 15 14 13 12 11 10 9 V-REF CTL VCC DRIVE PWM CONTROL LOGIC DRIVE OSC DTC GND 1 2 3 4 5 6 7 8 1.7 3.1 1.3 1.3 1.6 3.6 0 3.7 C1003 0.1 R1004 0 C1007 0.1 15.5 D1068 R1063 18K CN1050 2 1 R1001 22K R1014 4.7K R1018 2.2K D1050 OPEN D1063 R1062 390 D1067 C1066 1500P Q1060 KTC3198-Y-AT/P OVER VOLTAGE PROTECTOR 0.7 C1064 R1064 0.01 8.2K D1073 D1060 C1112 1500P R1050 OPEN BC1551 BEAD C1051 OPEN Q1503 KTC3198 -Y-AT/P (SWITCHING) 4.0 0.3 0 R1506 1K R1002 C1002 1K 0.01 D1002 OPEN 5 82.5 D 4.0 Q1552 2SA950-O (DRIVE) R1503 2.2K R1504 2.2K R1505 1K R1810 4.7K R1806 22K R1019 WIRE R1040 0.39 /2W R1502 150 R1802 22K C1014 6800P R1044 0.39 /2W Q1551 2SC2120-Y (DRIVE) 3.9 Q1553 KTC3198 -Y-AT/P (SWITCHING) 4.0 -0.3 0 R1556 1K R1555 1K Q1801 KTA1267-GR-AT/P (SW+16V) 15.7 15.7 R1809 1.5K 15.0 C1802 0.1 R1807 1K R1045 OPEN R1552 150 C1552 0.01 D1801 10BSB-T26 R1812 12K C1550 470P/2KV R1041 33K R1042 OPEN R1553 2.2K 3 C1055 OPEN R1061 20K C1111 15P/6.3KV R1110 100K C1050 OPEN R1701 1K R1811 100K 6 D1702 3.9 Q1815 2SA950-O R1804 (SW+16V) 1.2 15.8 15.7 R1805 1K 15.0 Q1800 R1803 KTC3198-Y-AT/P 4.7K 0.1 SWITCHING BACKLIGHT-ON R1801 C1801 0.7 0 22K 22/35V 6.6 R1931 47K Q1972 KTC3198-Y-AT/P 3.3 R1988 (SWITCHING) 1K 0.3 0 R1987 C1983 820K OPEN 7 1 D1703 C1703 0.22 C1981 0.01 D1930 27BSB-T26 D1933 R1937 0.33/2W R1009 82K R1043 12K 2 Q1971 KTC3198-Y-AT/P 1.1 (SWITCHING) R1986 1K 0.2 0 C1982 0.47/50V R1930 47 D1934 39BSB-T26 C1702 0.22 C1040 0.47 R1981 0 Q1931 KTC3198-Y-AT/P (SWITCHING) R1008 2.2K 4 R1065 27K D1064 D1061 C1072 0.1 R1700 9.1K D1972 IC1931 LTV817MCF (ISOLATOR) 0 R1979 6.8K R1980 360 V9 10 11 12 13 14 2.5 0.4 0 0.4 2.5 0 8 0 81.0 0 C1931 1000P /100V D1000 15BSB -T26 R1007 10K R1970 270 1 C1934 OPEN IC1700 BA10324AF-E2 (COMPARATOR) C1004 0.1 D1062 T1050 INVERTER C1054TRANS OPEN 8 2 2.6 0.4 15.7 0.4 2.5 0 6 5 4 3 2 1 V+ D1973 C1970 0.047 /100V D1970 5V6BSB-T26 IC1930 LTV817MCF (FEEDBACK) 10.4 Q1930 TK8A50D (SWITCHING) G 0.2 R1974 OPEN 0 7 R1973 22K D1971 HZZS33NB2TE-EQ R1968 3.9K R1967 3.9K C1062 1500P D1701 D1700 R1984 15K R1969 3.9K 15 C1056 100/100V R1005 220K R1006 56K D1960 OPEN D1961 OPEN D1931 5V6BSB-T26 Q1932 2SC2120-Y 6.6 (SWITCHING) 8.4 D 6.6 R1972 68K R1971 3.9K R1990 330K R1991 330K R1945 390K 134.8 S R1983 33K R1975 30K R1976 30K R1977 27K C1991 OPEN 7 C1053 100/100V C1052 100/100V D1994 1ZB100BB 5 BC1930 BEAD C1930 820P /2KV C1992 470 /100V 4 BC1931 BEAD 3 C1061 15P/6.3KV R1060 100K C1990 820P/1KV R1021 10K D1001 WIRE C1008 0.1 R1011 R1010 10K 0 R1012 12K C1620 1000P C1005 0.1 UNLESS OTHERWISE SPECIFIED: DIODES ARE 1SS133. A B C D 11-7 E F G FL11.11SCINV Function Schematic Diagram FUNCTION CBA 2 TO IR SENSOR CBA CL103C AL+3.3V GND KEY-IN1 KEY-IN2 CL103B 1 2 3 4 R109 10K 1 R108 220 C108 0.1 D107 OPEN C151 0.1 D151 OPEN R111 4.7K R112 2.7K R113 4.7K SW101A POWER SW103A CH UP SW104A CH DOWN SW105A MENU SW106A VOL UP SW107A VOL DOWN SW101B OPEN POWER SW104B OPEN CH UP SW103B OPEN CH DOWN SW105B OPEN MENU SW107B OPEN VOL UP SW106B OPEN VOL DOWN R152 10K R115 18K R114 8.2K R151 WIRE R153 2.2K R154 2.2K SW151 PLAY SW152 STOP R155 OPEN SW153 EJECT R156 OPEN SW154 OPEN SW155 OPEN UNLESS OTHERWISE SPECIFIED: SWITCHES ARE SKHHLMA0100. A B C 11-8 FL11.11SCF IR Sensor Schematic Diagram IR SENSOR CBA 2 RS102 KSM-712TH2E (REMOTE SENSOR) C110 OPEN VOUT Vcc GND R123 220 D104 333GT/E POWER 1 2 3 R124 220 C111 OPEN TO POWER SUPPLY CBA CN101 GND REMOTE AL+3.3V LED1 P-ON-H1 KEY-IN1 KEY-IN2 DVD-LED CL101B R126 1 1K 2 3 4 5 6 7 8 D105 L-53HT STANDBY R125 220 C112 OPEN D106 LTL-307Y DVD R127 3.3K R128 100 C113 47/16V C115 330P CL103C 1 2 3 4 1 A C114 OPEN B TO FUNCTION CBA CL103B AL+3.3V GND KEY-IN1 KEY-IN2 C 11-9 FL11.11SCIR Digital Main 1 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT 4 3 TO POWER SUPPLY CN3003 CBA CN303 GND 29 DVD-SPDIF 28 GND 27 DVD-AUDIO(R) 26 DVD-AUDIO-MUTE 25 DVD-AUDIO(L) 24 GND 23 DVD-Y 22 GND 21 DVD-Pb 20 GND 19 DVD-Pr 18 GND 17 LED-CONT 16 DVD-DISC-OUT 15 GND 14 DVD-SCLK 13 GND 12 DVD-CS 11 GND 10 DVD-DISC-IN 9 DVD-SDATA 8 DVD-REMOTE 7 DVD-P-ON 6 DVD-MAIN-PWR 5 P-ON-H3(NU) 4 DVD-LED 3 KEY-IN2 2 GND 1 CONTINUE DIGITAL 4 DVD-LED DVD-MAIN-PWR DVD-P-ON DVD-SDATA DVD-CS DVD-SCLK LED-CONT CONTINUE DIGITAL 3 KEY-IN2 DVD-AUDIO(L) DVD-SPDIF DVD-AUDIO-MUTE DVD-AUDIO(R) R3417 100 C3295 33P R3419 680 C3296 OPEN R3420 100 R3473 680 R3474 1000P C3266 OPEN C3294 33P R3418 1000P C3267 33P CONTINUE DIGITAL 5 LCD+12V C3268 33P 8 C3269 33P R3471 100 R3472 100 C3271 100P C3270 100P 1 R3425 100 C3272 100P R3426 100 C3273 100P R3427 100 C3281 1000P C3280 100P C3279 100P C3278 100P C3277 100P C3276 100P C3275 100P R3430 100 R3433 100 6 5 R3007 OPEN 2 3 4 R3006 OPEN Q3001 OPEN R3428 100 R3432 100 7 Q3002 OPEN C3002 OPEN C3078 OPEN R3002 OPEN R3001 OPEN R3429 100 C3274 100P CONTINUE DIGITAL 2 DVD-REMOTE DVD-DISC-IN DVD-DISC-OUT DVD-Pr DVD-Pb DVD-Y *1 IC3005(1/6) R8J04013BG-RJ DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER 0 0 0 0 OPEN OPEN 0 0 0 0 OPEN OPEN OPEN OPEN 0 0 OPEN OPEN R3123 R3121 OPEN OPEN R3152 1K R3127 R3126 R3129 R3128 R3088 5.6K A B CN3005 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 TO LCD MODULE ASSEMBLY GND LLV0(+) LLV0(-) LLV1(+) LLV1(-) LLV2(+) LLV2(-) GND LLVCLK(+) LLVCLK(-) GND LLV3(+) LLV3(-) LLV4(+) LLV4(-) LLV5(+) LLV5(-) GND TP POL CPV OE1 XA0 STV CONTINUE DIGITAL 5 P-ON+3.3V TO DIGITAL MAIN 2 IC3005(2/6) REFR W14 TO LCD MODULE ASSEMBLY LCD+12V LCD+12V LCD+12V LCD+12V LCD+12V GND GND GND RX0(+) RX0(-) RX1(+) RX1(-) RX2(+) RX2(-) GND RXCLK(+) RXCLK(-) GND RX3(+) RX3(-) NU NU NU NU GND GND GND GND GND GND GND OPEN R3165 R3166 R3167 R3168 R3115 R3113 R3169 R3170 R3112 R3114 R3116 R3117 R3118 R3119 R3120 R3122 R3124 R3125 R3155 0 0 R3161 OPEN 1 R3164 R3163 OPEN OPEN OPEN OPEN OPEN LVDS TX AA17 AB17 Y16 W16 AB16 AA16 AB15 AA15 Y15 W15 AB14 AA14 AB13 AA13 Y13 W13 Y12 W12 AB12 AA12 Y11 W11 AB11 AA11 R3157 R3158 R3159 R3160 R3162 2 CN3004 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 OPEN 0 OPEN 0 CONTINUE DIGITAL 4 STV RESET-LCD OE CPV POL TP CONTINUE DIGITAL 2 RESET-LCD C D 11-10 E F FL11.11SCD1 Digital Main 2 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. R3144 100 R3142 100 R3138 100 DIGITAL MAIN CBA UNIT *1 IC3005(2/6) R8J04013BG-RJ DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER 4 TO DIGITAL MAIN 3 IC3005(3/6) R3193 4.7K L3024 C3243 R3369 OPEN OPEN OPEN R3338 0 F1 DEMODULATOR /MPEG DECODER R3345 0 C3226 10P R3354 0 L3022 0.27uH C3219 C3220 C3221 C3222 0.1 10 0.1 0.1 R3337 0 C3235 33P R3344 0 A1 NU E2 NU E1 NU R3202 2.2K IF-AGC J1 R3194 2.2K C3178 0.1 C3177 0.33 R3353 0 R3360 0 IC3012 (OPEN) (MEMORY) L3023 OPEN C3242 R3368 OPEN OPEN C3084 OPEN HDMA-SCL Y18 HDMI-SDA W19 R3188 R3187 R3218 R3190 10K VCC 8 2 A1 WP 7 3 A2 SCL 6 4 GND SDA 5 C3211 OPEN R3310 OPEN DVD-DISC-IN N21 DVD-DISC-OUT M19 R3228 22 R3467 R3466 OPEN OPEN R3229 22 R3296 R3298 C3194 C3195 C3196 HSIN B14 VSIN B15 C11 C8 D9 C3197 C3198 C3199 C3200 C3201 C3202 C14 A11 B12 D8 A8 B7 NU A10 NU C7 A12 C3098 33P Q3033 2SC4081UBTLQ (BEFFER) R3436 10K R3297 OPEN R3295 OPEN G 100 R3172 100 C3099 100P C3101 100P C3100 33P C3102 33P C3103 33P R3175 100 OPEN OPEN OPEN OPEN OPEN 0.01 0.1 0.1 0.1 0.1 0.1 C3104 33P IC3013 (OPEN) (BUFFER GATE) 1 VCC 5 C3293 OPEN C3292 OPEN C3291 OPEN R3403 R3402 R3401 R3400 R3399 C3105 1000P C3112 100P R3154 R3171 R3179 C3214 OPEN 2 C3107 33P R3181 0 C3111 100P 100 100 0 3 GND 4 IC3014 (OPEN) (BUFFER GATE) 1 VCC 5 0 0 0 0 0 3 GND R3398 0 C3203 0.1 D3027 OPEN C3290 C3284 C3285 C3286 0.01 0.1 0.1 0.1 R3343 OPEN H R3358 OPEN D3050 OPEN R3347 OPEN R3286 OPEN Q3010 OPEN R3460 0 R3459 0 R3458 0 JK3001(OPEN) D-SUB CONNECTOR R3183 OPEN R3356 OPEN D3049 OPEN R3364 OPEN D3053 OPEN R3377 OPEN D3055 OPEN R3186 OPEN OPEN OPEN OPEN R3184 OPEN I J 11-11 CN3006 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 TO POWER SUPPLY CBA CN302 KEY-IN1 DIF-OUT2 GND DIF-OUT1 GND IF-AGC RESET SCL SDA AUDIO-MUTE COM-VIDEO-Pr-IN GND COM-VIDEO-Pb-IN GND COM-VIDEO-Y-IN GND AUDIO(L) INPUT0 AUDIO(R) INPUT1 GND S-VIDEO-Y-IN GND S-VIDEO-C-IN S-VIDEO-SW VIDEO-IN GND SPDIF GND CONTINUE DIGITAL 3 AUDIO(L) AUDIO(R) SPDIF CONTINUE DIGITAL 6 WP HDMI-SDA HDMI-SCL CONTINUE DIGITAL 1 RESET-LCD D3045 OPEN R3416 R3185 OPEN OPEN R3476 R3477 R3478 0.1 0.1 0.1 0.1 0.1 0.1 0.1 R3376 OPEN R3180 OPEN R3284 OPEN R3285 OPEN C3204 C3205 C3206 C3207 C3208 C3209 C3210 D3040 OPEN CONTINUE DIGITAL 3 KEY-IN1 LIGHT-SENS RESET CONTINUE DIGITAL 5 P-ON+5V AL+3.3V-2 P-ON+3.3V 4 R3339 OPEN OPEN OPEN OPEN TO DIGITAL TO DIGITAL MAIN 6 MAIN 1 IC3005(6/6) IC3005(1/6) R3156 R3435 100 2 A15 C12 A7 B8 B6 C9 E3 B9 A13 A14 B13 B11 A9 A6 B10 C3093 33P C3092 1000P C3095 33P C3287 C3288 C3289 1 NU NU NU NU NU NU NU NU NU NU NU D3041 OPEN C3089 33P OPEN OPEN OPEN OPEN OPEN OPEN DIGITAL SIGNAL PROCESS NU DVD-Y DVD-Pb DVD-Pr R3321 OPEN R3333 OPEN R3334 OPEN 22 22 22 C3259 C3257 C3258 C3254 C3255 C3256 A/D CONVERTER R3326 OPEN R3437 10K R3219 22 SW 1 A0 C3074 1000P R3189 10K DVD-REMOTE W18 2 Q3012 OPEN (BUFFER) D3054 OPEN INPUT0 K1 INPUT1 L4 S-VIDEO-SW AB22 3 R3134 100 C3086 1000P Q3011 OPEN (BUFFER) F2 C3225 10P R3192 4.7K R3361 0 C3087 33P R3404 100 D3056 OPEN CONTINUE DIGITAL 4 AUDIO-MUTE SDA SCL 11 6 1 12 7 2 13 8 3 14 9 4 15 10 5 CONTINUE DIGITAL 1 DVD-REMOTE DVD-DISC-IN DVD-DISC-OUT DVD-Pr DVD-Pb DVD-Y K L FL11.11SCD2 Digital Main 3 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT 4 CONTINUE DIGITAL 2 AUDIO(L) AUDIO(R) SPDIF R3335 R3336 18K 18K L3038 BLM21PG221SN1D R3331 OPEN R3327 OPEN L3040 BLM21PG221SN1D IC3017 SN74LVC1G126DCKR (BUFFER GATE) VCC 5 1 3 GND C3250 0.1 R3439 100 *1 IC3005(3/6) R8J04013BG-RJ DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER C3248 220P R3325 4.7K C3249 10 R3362 0 C3245 OPEN R3332 4.7K C3229 82P TO DIGITAL MAIN 2 IC3005(2/6) 2 AUDIO I/F TO DIGITAL MAIN 6 IC3005(6/6) MADIN0 KEY-IN1 KEY-IN2 PROTECT1 PROTECT2 PROTECT3 DTV-ON-H2 LED-R NU NU NU NU NU NU NU NU NU M C4 C3 C1 C2 B2 B1 B5 B4 A2 A3 A4 A5 B3 R3195 R3196 R3197 R3208 R3198 R3199 R3200 R3201 R3209 R3210 22 22 22 100 22 22 22 22 100 100 R3211 R3212 R3213 22 22 22 2 6 15 14 13 5 LPF LPF 3 GND 4 IC3010 PCM1782DBQR AUDIO D/A CONVERTER R3214 R3205 22 100 R3312 R3313 R3314 R3315 R3316 R3317 R3318 R3465 22 OPEN 22 22 22 22 22 22 C3215 0.1 C3216 10 C3110 0.1 R3355 R3350 3.9K 68K C3237 82P R3342 4.7K 2 3 4 5 10 NU 6 7 8 C3232 82P IC3009 PST8420UR (RESET) 1 GND OUT 4 R3178 10K C3106 0.1 C3252 0.1 R3191 100 R3182 4.7K C3116 OPEN CD 3 CONTINUE DIGITAL 6 HDMI-CEC HDMI-HPD0 HDMI-HPD1 HDMI-HPD2 CONTINUE DIGITAL 2 KEY-IN1 LIGHT-SENS RESET CONTINUE DIGITAL 5 PROTECT1 PROTECT2 PROTECT3 DTV-ON-H2 DTV-ON-H1 LED-R P-ON-H2 REMOTE VCOM-PWM 22 C3218 10 R3445 CONTINUE DIGITAL 1 KEY-IN2 DVD-AUDIO(L) DVD-SPDIF DVD-AUDIO-MUTE DVD-AUDIO(R) 1K R3447 10K N C3120 0.01 CONTINUE DIGITAL 4 CPU-RESET-N MADIN0 C3113 0.033 R3446 10K C3283 10 C3109 10 AUDIO SERIAL PORT R3475 100K R3444 R3173 OPEN 9 NU C3217 10 C3282 10 R3174 OPEN ENHANCED MULTI-LEVEL DELTA-SIGMA MODULATOR SYSTEM CLOCK MANAGER SERIAL CONTROL PORT 1 12 11 GND VCC DAC DAC 4X/8X OVERSAMPLING DIGITAL FILTER /FUNCTION CONTROLLER ZERO DETECT 2 VDD H19 G21 G20 H21 G22 H22 H20 J21 G1 G2 NU G3 1 8 7 VCC 1 R3394 12K R3176 0 C3108 10 C3230 82P IC3015 NJM4558M(TE1) (OP AMP) R3320 OPEN C3224 10 LRCLK M1 ACLK L3 M2 DVD-AUDIO-MUTE M3 BCLK L1 STXD0 AB10 SRXD0 AA10 SCLK0 Y10 SPDIF L2 DTV-ON-H1 M21 P-ON-H2 K20 HDMI-HPD1 J19 HDMI-HPD0 J20 REMOTE K21 HDMI-CEC K22 RESET-N T20 NU P18 HDMI-HPD2 J22 VCOM-PWM AB21 R3177 0 R3341 4.7K R3393 12K R3438 OPEN 3 R3330 4.7K R3440 100 4 L3013 BLM21PG221SN1D 16 C3251 100/16V 4 2 C3223 R3322 10 4.7K C3227 82P 2 3 GND C3241 82P R3359 R3352 R3351 0 3.9K 68K R3311 OPEN IC3016 SN74LVC1G126DCKR (BUFFER GATE) VCC 5 1 CONTINUE DIGITAL 4 C7-SPD-EN DVD-SPD-EN C3244 OPEN CONTINUE DIGITAL 5 P-ON+3.3V P-ON+5V AUDIO(L)-OUT AUDIO(R)-OUT AMP(L)-OUT AMP(R)-OUT AL+3.3V O P 11-12 Q R FL11.11SCD3 Digital Main 4 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. R3064 100 *1 IC3005(4/6) R8J04013BG-RJ DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER C3050 0.1 R3065 100 4 C3029 C3030 C3031 C3032 C3033 C3034 C3035 C3036 C3037 C3038 C3039 C3040 C3041 C3042 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 IC3002 K4T51163QG-HCF7 (DDR2 SDRAM) *A VDD 1-V3 2-V3 3-V3 SD-DQ8 SD-DQ14 SD-DQ15 SD-DQ12 SD-DQ11 SD-DQ10 SD-DQ9 SD-DQ13 3 4-V3 5-V3 6-V3 SD-DQ7 SD-DQ6 SD-DQ5 SD-DQ3 SD-DQ4 SD-DQ2 SD-DQ1 SD-DQ0 VREF J2 CKE CK CK CS RAS CAS WE BA2/NU BA1 BA0 A12 A11 A10/AP A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 ODT R3026 100 C3010 R3027 0.1 100 K2 J8 K8 L8 K7 L7 K3 L1 L3 L2 R2 P7 M2 P3 P8 P2 N7 N3 N8 N2 M7 M3 M8 K9 E2 A2 R8 R7 R3 NU NU NU NU NU B7 A8 B3 B9 B1 D9 D1 D3 D7 C2 C8 F7 E8 F3 F9 F1 H9 H1 H3 H7 G2 G8 UDQS UDQS/NU UDM DQ15 DQ14 DQ13 DQ12 DQ11 DQ10 DQ9 DQ8 LDQS LDQS/NU LDM DQ7 DQ6 DQ5 DQ4 DQ3 VSS *B DQ2 *A:A1,A9,C1,C3,C7,C9,E1,E9, G1,G3,G7,G9,J1,J9,M9,R1 DQ1 *B:A3,A7,B2,B8,D2,D8,E3,E7, DQ0 F2,F8,H2,H8,J3,J7,N1,P9 R3049 120 2 IC3006 W25X32VSSIGE (MEMORY) 1 CS 2 SO R3104 10K 1 (USB JACK) USB+5V USB(-) USB(+) GND CN3009 1 L3025 2 3 4 VCC 8 NU 7 3 WP SCK 6 4 GND SI 5 R3102 10K L3004 BLM21PG221SN1D R3107 10K C3073 0.1 R3071 130 22 22 22 22 4.7 4.7 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 130 R3091 47 R3092 47 R3089 47 R3094 47 R3093 47 P2 N4 T2 R4 P4 R2 R3 R1 V1 T4 W2 V4 W3 W1 U4 V2 N3 U3 P1 N2 U1 U2 SD-DQ15 SD-DQ14 SD-DQ13 SD-DQ12 SD-DQ11 SD-DQ10 SD-DQ9 SD-DQ8 SD-DQ7 SD-DQ6 SD-DQ5 SD-DQ4 SD-DQ3 SD-DQ2 SD-DQ1 SD-DQ0 SD-UDM SD-LDM SD-UDQSN SD-UDQS SD-LDQSN SD-LDQS AB2 AA3 W6 Y4 AA1 Y2 W8 AA2 AB8 AB5 AB6 AA7 AA5 AA8 AB4 AA6 AA4 AB7 W5 W7 AB3 Y8 Y6 W9 AA9 SD-RAS SD-CAS SD-WE SD-CS SD-CLKN SD-CLK SD-CKE SD-ODT SD-A12 SD-A11 SD-A10 SD-A9 SD-A8 SD-A7 SD-A6 SD-A5 SD-A4 SD-A3 SD-A2 SD-A1 SD-A0 SD-BA2 SD-BA1 SD-BA0 NU CPV STV TP NU OE POL AUDIO-MUTE GPY10 R3450 T19 U22 V22 L21 U20 P22 R21 P19 P20 P21 M22 N22 W17 Y17 K19 L20 R3451 22 R3226 22 R3227 R3449 R3225 R3448 R3215 R3216 R3217 R3230 R3231 R3232 R3233 AA18 AA19 AB19 R3454 22 AA20 AB20 Y19 L19 L22 TXD0 R19 RXD0 R20 R3234 R3421 10K 100 R3422 100 R3468 100 R3469 100 XIN25 T22 XOUT25 T21 DVD-MAIN-PWR DVD-P-ON BACKLIGHT-SW P-ON-H1 OE2 U19 V20 W20 Y22 AB18 C3184 15P X3001 25MHz C3183 15P R3235 1M R3223 510 R3442 R3443 R3095 R3096 R3090 R3224 10K 100 22 22 22 R3453 OPEN 22 22 22 10K 22 22 22 CN3010 1 2 3 4 R3395 4.7K R3396 4.7K C3253 OPEN R3461 100 R3462 100 R3463 100 22 22 22 22 22 USB-EN W21 R3098 4.7K DVD-SPD-EN GPIO6 USB(+) USB(-) NU J3 NU F22 AA21 WP AA22 SOUT Y20 CS V19 SCK Y21 SIN R3131 22 R3470 100 W22 V21 H2 H1 NU J4 NU H3 SCL K3 SDA K2 R3099 C3076 C3075 C3072 C3071 R3206 R3207 6.04K 10 0.1 10 0.1 C3246 1 D3052 OPEN Q3009 2SB1732TL (SW+5V) R3108 10K R3441 OPEN Q3008 2SC4081UBTLQ (SWITCHING) T R3150 10K C3096 1 R3146 1K R3147 10K R3148 15K C3091 OPEN 22 22 D3002 AS431AKTR-E1 R3140 33K R3141 180 R3204 4.7K R3203 4.7K R3136 1.6 L3041 BLM21PG221SN1D CONTINUE DIGITAL 1 DVD-LED DVD-MAIN-PWR DVD-P-ON DVD-SDATA DVD-CS DVD-SCLK LED-CONT CONTINUE DIGITAL 6 GPIO6 CONTINUE DIGITAL 5 GPY10 P-ON-H1 LED1 BACKLIGHT-SW BACKLIGHT-ADJ CPU-RESET-N OE2 CONTINUE DIGITAL 3 CPU-RESET-N MADIN0 R3139 33K R3135 2.4 (NO CONNECTION) P-ON+5V UART0-TX UART0-RX GND CONTINUE DIGITAL 2 AUDIO-MUTE SDA SCL L3043 BLM21PG221SN1D EXC24CG900U R3153 R3151 330 330 S 3-S3 6-S3 2-S3 1-S3 5-S3 4-S3 R3029 R3030 R3031 R3028 R3024 R3015 R3016 R3048 R3035 R3036 R3037 R3038 R3039 R3040 R3041 R3042 R3043 R3044 R3045 R3046 R3047 R3032 R3033 R3034 R3070 DVD-SDATA M32TRST-N RESET-LCD LED-CONT DVD-SCLK ASEBRKAK-N ASEMD0 TRST-N TCK TDI TDO TMS BACKLIGHT-ADJ C7-SPD-EN LED1 DVD-LED C3051 0.1 SD-DQ15 SD-DQ14 SD-DQ13 SD-DQ12 SD-DQ11 SD-DQ10 SD-DQ9 SD-DQ8 SD-DQ7 SD-DQ6 SD-DQ5 SD-DQ4 SD-DQ3 SD-DQ2 SD-DQ1 SD-DQ0 C3009 0.1 R3452 DVD-CS U21 R5 SD-VREF0 V7 SD-VREF1 (NO CONNECTION) P-ON+5V UART0-TX NU NU UART0-RX M32TDI AL+3.3V M32TDO M32TRST-N RESET-LCD GND M32TMS ASEBRKAK-N ASEMD0 TRST-N TCK TDI TDO TMS CPU-RESET-N CONTINUE DIGITAL 3 C7-SPD-EN DVD-SPD-EN CONTINUE DIGITAL 1 STV RESET-LCD OE CPV POL TP CN3007 1 2 3 4 5 OPEN 6 7 OPEN 8 9 10 11 12 13 14 15 16 17 18 19 20 CONTINUE DIGITAL 5 P-ON+1.8V P-ON+3.3V AL+3.3V P-ON+5V DIGITAL MAIN CBA UNIT U V 11-13 W X FL11.11SCD4 Digital Main 5 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. R3068 R3058 R3083 DIGITAL MAIN CBA UNIT CONTINUE DIGITAL 3 PROTECT1 PROTECT2 PROTECT3 DTV-ON-H2 DTV-ON-H1 LED-R P-ON-H2 REMOTE VCOM-PWM CONTINUE DIGITAL 4 GPY10 P-ON-H1 LED1 BACKLIGHT-SW BACKLIGHT-ADJ CPU-RESET-N OE2 CONTINUE DIGITAL 4 P-ON+1.8V P-ON+3.3V AL+3.3V P-ON+5V CONTINUE DIGITAL 1 P-ON+3.3V 100 100 100 *1 IC3005(5/6) R8J04013BG-RJ DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER 2 *A:L9~L14,M13,M20, N18~N20,P9,V6, V8,V16 *B:K9~K14,K18,M5, M9~M12,M18,N9, N12,P3,P5,P12, P14,R18,T3,U5, U18,V5,V9,V12, V14,V17,W4,Y3, Y7,Y14,AB1,AB9 1 R3221 100 IC3004 BD7820FP-E2 (+1.8V REG.) AVDD33 AVDD33 AVDD33 AVDD33 AVDD33 VDD33HDMI VDD33HDMI VDD33HDMI VDD33HDMI VDD33IO AVDD33PLL AVDD33AUD MIXVDD33 MIXVDD33 MIXVDD33 MIXVDD33 MIXVDD33 C3124 0.1 C3125 0.1 C3126 0.1 C3127 0.1 C3128 0.1 C3129 0.1 C3130 0.1 C3131 0.1 C3132 0.1 C3133 10 C3134 OPEN C3136 0.1 C3137 0.1 C3138 0.1 C 1 2 3 4 5 L3001 2uH R3009 100 R3017 100 C3004 1000P C3023 10 C3018 100/16V C3024 10 R3061 1K R3060 1K R3059 390 C3027 0.1 C3049 100/4V C3263 1 C3139 10 C3140 0.1 C3141 0.1 C3142 0.1 C3143 0.1 C3144 0.1 C3145 0.1 Q3003 2SC4081UB-TLQ (SWITCHING) Q3004 R3079 2SC4081UB-TLQ (SWITCHING) 10K CONTINUE DIGITAL 2 P-ON+5V AL+3.3V-2 P-ON+3.3V CONTINUE DIGITAL 6 AL+3.3V-2 P-ON+3.3V C3054 1 R3086 2.2K R3084 2.2K R3077 10K L3014 BLM21PG221SN1D C3114 10 C3115 100 C3117 0.1 C3118 0.1 C3119 0.1 C3146 0.1 C3147 0.1 C3148 0.1 C3149 0.1 C3150 0.1 C3153 OPEN C3264 0.01 C3151 0.1 C3152 0.1 C3155 10 C3156 0.1 C3160 0.1 C3161 0.1 1 2 3 4 5 C3068 10 C3069 10 D3105 1SS400 C3053 0.1 R3110 1K R3109 390 C3070 0.1 R3111 1K C3162 0.1 C3082 0.1 C3081 10 R3062 OPEN R3424 D3103 100 1SS400 L3003 BLM21PG221SN1D C3080 10 L3019 BLM21PG221SN1D C3164 0.1 C3165 0.1 C3170 0.1 C3171 0.1 C3172 0.1 C3166 0.1 C3167 10 C3168 0.1 C3169 0.1 C3174 0.1 C3175 0.1 Q3101 2SC4081UB-TLQ (SWITCHING) C3265 10 R3097 2.2K C3176 10 2 VIN 3 SW 4 GND R3340 6.8K R3100 22K C3005 1000P C3006 1000P C3011 100P C3008 100P R3050 0 C3015 10 C3016 0.1 R3054 0 C3019 10 C3022 0.1 C3028 10 C3043 0.1 R3063 OPEN R3073 0 D3001 SK22A L3044 BLM21PG221SN1D R3066 0 R3072 Q3006 2SA1774 (SWITCHING) C3094 47/4V C3097 10 C3047 0.1 100 C3048 1000P 100 C3067 1000P R3133 10K R3087 R3085 R3078 R3074 R3149 0 R3145 6.04K C3057 1000P R3143 15K Z AA BB 11-14 C3055 1000P C3062 1000P R3101 C3090 1 R3137 6.8K C3088 0.015 C3044 1000P R3464 OPEN D3101 1SS400 D3102 1SS400 COMP 6 FB 5 C3045 10 C3046 1000P EN 7 L3009 10uH C3231 0.1 C3228 0.1 R3106 22K R3105 1K Q3005 2SC4081UB-TLQ IC3008 (SWITCHING) BD9321EFJ-E2 (DC-DC CONVERTER) C3083 0.1 1 BST SS 8 C3085 0.1 R3319 1K 100 R3003 OPEN R3423 47K L3020 BLM21PG221SN1D C3173 0.1 100 C3077 100/16V D3106 1SS400 D3104 1SS400 C3163 10 R3011 R3014 R3005 OPEN C3157 0.1 C3052 10 C3159 0.1 R3004 OPEN BC3001 2.2uH L3017 BLM21PG221SN1D C3066 220/16V C3154 10 CONTINUE DIGITAL 1 LCD+12V IC3007 BD7820FP-E2 (+1.8V REG.) C3079 100/4V CONTINUE DIGITAL 6 HDMI-VDD33 Y 100 L3016 BLM21PG221SN1D C6 C13 D2 D10 E8 E18 G18 E17 J18 D14 H5 F5 D1 D5 E4 E5 F4 REXT D11 LPF H4 C3123 0.1 C N1 N5 T1 T5 V3 Y1 Y5 Y9 J9 J10 J11 J12 E10 E12 D13 J13 E15 C3122 0.1 OUT VCCQ18 VCCQ18 VCCQ18 VCCQ18 VCCQ18 VCCQ18 VCCQ18 VCCQ18 VDD18 VDD18 VDD18 VDD18 AVDD18 AVDD18 VDD18HDMI VDD18HDMI VPPOTP C3121 0.1 OUT M4 V13 V15 V18 W10 P10 N10 P11 P13 T18 L3015 BLM21PG221SN1D R3010 GND VCCQ33 VCCQ33 VCCQ33 VCCQ33 VCCQ33 PLLAVCC PLLAVCC PLLAVCC PLLAVCC PLLAVCC C3003 100P VCC *A V10 N11 V11 N13 N14 R3008 100 R3222 10K C3182 0.1 C3181 0.1 VDD12 PLLDVDD PLLDVDD PLLDVDD PLLDVDD PLLDVDD Q3013 SSM3K309T (SW+3.3V) GND C3179 0.1 R3220 0 VCC C3180 0.1 CTL K5 J2 K4 R22 L18 M14 CTL VDDA33RU VDDA33USB VDDA33USB VCC33STB VCC33STB VDDSTB S 3 VSS NU NU AVSS18 AVSS18 AVSS AVSS AVSS AVSS AVSS VSSHDMI VSSHDMI VSSHDMI VSSHDMI VSSHDMI VSSHDMI VSSIO AVSS33PLL AVSS33AUD AVSS33AUD MIXVSS33 MIXVSS33 MIXVSS33 VSSAUSB G *B C5 D4 E9 E11 C10 D3 D7 D12 E7 E13 E16 F18 G19 H18 J14 E14 J5 G4 G5 D6 E6 F3 L5 D 4 CC C3061 1000P C3063 1000P 100 100 100 100 TO POWER SUPPLY CBA CN301 VCOM-PWM BACKLIGHT-ADJ LED1 BACKLIGHT-SW REMOTE OE2 GND AL+3.3V AL+3.3V P-ON+3.3V P-ON+3.3V GND GND P-ON+7V PROTECT2 P-ON+5V P-ON+5V GND PROTECT1 P-ON+3V P-ON-H1 AMP(R)-OUT GND AMP(L)-OUT PROTECT3 AUDIO(R)-OUT GND AUDIO(L)-OUT P-ON-H2 CONTINUE DIGITAL 3 P-ON+3.3V P-ON+5V AUDIO(L)-OUT AUDIO(R)-OUT AMP(L)-OUT AMP(R)-OUT AL+3.3V CN3002 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 C3065 1000P DD FL11.11SCD5 Digital Main 6 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into six and shown as IC3005 (1/6) ~ IC3005 (6/6) in this Digital Main Schematic Diagram Section. *1 IC3005(6/6) R8J04013BG-RJ DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER DIGITAL MAIN CBA UNIT R3244 R3243 R3242 R3241 R3240 R3239 R3238 R3261 C19 C20 D19 D20 A21 A22 B21 B22 DDC0-SCL A16 DDC0-SDA C16 4 3 R3252 R3251 R3250 R3249 R3248 R3247 R3246 R3245 TO DIGITAL MAIN 3 IC3005(3/6) VIDEO DECODER PLL-XFC-P E22 PLL-XFC-X E21 0 0 0 0 0 0 0 0 R3275 OPEN R3387 R3370 OPEN OPEN CONTINUE DIGITAL 5 AL+3.3V-2 P-ON+3.3V CONTINUE DIGITAL 2 L3032 EXC28CG900U R3391 0 C3185 0.01 R3236 560 R3292 OPEN Q3022 OPEN (BUFFER) C3262 OPEN R3411 OPEN R3300 OPEN 1 R3382 0 R3366 0 R3276 R3388 47K 0 Q3024 2SK3018 (BUFFER) R3293 10K R3273 47K R3301 10K R3270 C3187 4.7 7.5K C3186 0.1 R3271 C3188 2200P 3K R3272 C3189 0.022 6.8K C3261 1 Q3020 2SK3018 (BUFFER) R3410 2.7K D3058 1SS400 R3413 OPEN R3373 OPEN Q3015 R3266 2SK3018 4.7K (BUFFER) R3407 1K R3263 4.7K R3383 10K L3034 EXC28CG900U Q3016 R3267 2SK3018 4.7K (BUFFER) R3405 100 R3264 4.7K L3036 EXC28CG900U Q3019 OPEN (BUFFER) R3415 82K D3057 RB751S-40TE61 C3190 OPEN Q3017 R3268 OPEN OPEN (BUFFER) Q3034 OPEN (SWITCHING) WP HDMI-SDA HDMI-SCL R3412 OPEN R3408 OPEN 0 0 0 0 0 0 0 0 IC3011 BU9883FV-WE2 (HDMI SERIAL EEPROM) R3262 OPEN L3039 BLM21PG221SN1D CONTINUE DIGITAL 4 GPI06 R3371 OPEN R3386 OPEN R3260 R3259 R3258 R3257 R3256 R3255 R3254 R3253 R3456 4.7K 1 VCC1 VCC2 16 2 SCL1 SCL2 15 3 SDA1 SDA2 14 4 WPB R3455 4.7K CONTINUE DIGITAL 3 HDMI-CEC HDMI-HPD0 HDMI-HPD1 HDMI-HPD2 OPEN OPEN R3278 OPEN D3060 OPEN Q3018 2SK3018 (BUFFER) R3237 27K HDMICONNECTOR-1 DATA2(+) TMDS DATA2 SHIELD DATA2(-) DATA1(+) TMDS DATA1 SHIELD DATA1(-) DATA0(+) TMDS DATA0 SHIELD DATA0(-) CLOCK(+) TMDS CLOCK SHIELD CLOCK(-) HDMI-CEC NU HDMI-CLOCK HDMI-DATA GND +5V HOT PLUG DETECT R3390 OPEN CONTINUE DIGITAL 5 HDMI-VDD33 Q3014 2SK3018 (BUFFER) Q3030 OPEN (SWITCHING) JK3003 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 R3372 19 1K L3028 OPEN PWR0 C15 PWR1 B16 PWR2 C18 TO DIGITAL PLL-XFC-A F21 MAIN 2 IC3005(2/6) 2 OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN L3030 EXC28CG900U A17 B17 A18 B18 A19 B19 A20 B20 DDC2-SCL D17 DDC2-SDA C17 EXT-RES D18 AUDIO DECODER HDMICONNECTOR-3 DATA2(+) TMDS DATA2 SHIELD DATA2(-) DATA1(+) TMDS DATA1 SHIELD DATA1(-) DATA0(+) TMDS DATA0 SHIELD DATA0(-) CLOCK(+) TMDS CLOCK SHIELD CLOCK(-) HDMI-CEC NU HDMI-CLOCK HDMI-DATA GND +5V HOT PLUG DETECT R3381 R3365 C21 C22 D21 D22 E19 E20 F19 F20 DDC1-SCL D15 DDC1-SDA D16 HDMI I/F JK3002 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 L3026 OPEN C3192 0.1 R3282 100 R3281 100 5 VCC-OUT NU 13 C3191 0.1 R3392 0 R3384 R3367 C3212 0.1 C3213 0.1 GND 12 6 SDA0 SDA3 11 7 SCL0 SCL3 10 8 VCC0 VCC3 9 R3294 10K R3274 47K Q3023 2SK3018 (BUFFER) R3277 47K 0 0 R3389 0 R3374 1K C3260 R3409 1 2.7K D3059 1SS400 R3302 10K Q3031 2SC4081UBTLQ (SWITCHING) JK3004 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 HDMICONNECTOR-2 DATA2(+) TMDS DATA2 SHIELD DATA2(-) DATA1(+) TMDS DATA1 SHIELD DATA1(-) DATA0(+) TMDS DATA0 SHIELD DATA0(-) CLOCK(+) TMDS CLOCK SHIELD CLOCK(-) HDMI-CEC NU HDMI-CLOCK HDMI-DATA GND +5V HOT PLUG DETECT R3414 OPEN R3375 OPEN R3406 1K R3385 10K EE FF GG HH 11-15 II Q3032 2SC4081UBTLQ (SWITCHING) JJ FL11.11SCD6 DVD Main 1 Schematic Diagram 2 NOTE: Either IC461 or IC462 is used for DVD MAIN CBA UNIT. DVD MAIN CBA UNIT CONTINUE DVD MAIN 2 FD-OFST TD-OFST VREFH VREF165 SLD STBY FOCUS DRIVE TRACKING DRIVE SPDL LPCO1 LPCO2 LPC VIN1RF VIN2RF VIN3RF VIN4RF VIN5 VIN6 VIN7 VIN8 CD/DVD IC202 LM324PWR (OP AMP) 1 2 3 VCC 4 5 6 7 R280 1K R281 10K R283 10K R279 47K R277 47K C281 0.1 R278 47K R285 22K R269 2K C289 3300P C288 3300P R284 10K R282 10K R234 R233 R232 R231 CONTINUE DVD MAIN 2 LOAD-DISC SP-ROT SL-ADS 8 CONTINUE DVD MAIN 2 EV+1.2V EV+3.3V(D) EV+3.3V(A) CONTINUE DVD MAIN 3 EV+3.3V(D) R264 1K C280 0.1 R286 2.2K C284 6800P R276 47K 1K 1K 1K 1K R813 0 R815 4.7K 2.2K 2.2K 2.2K 2.2K 1 1 1 1 4 14 13 12 11 10 9 GND R225 R226 R227 R228 C217 C218 C219 C220 3 PICK UP UNIT C201 0.1 TS FS DETECTOR 7 9 11 2 3 6 5 4 2 SPINDLE MOTOR DRIVE CBA M L201 47uH TS(+) FS(+) FS(-) TS(-) GND(CD-PD) GND(DVD-PD) PD-MONI DVD-LD GND(LD) CD-LD GND NU VREF NU B C A D CD/DVD DVD-ON+5V SP(+) SP(-) GND SL(-) SL(+) LOAD-DISC M SLED MOTOR CN201 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 C232 0.01 R251 3.3 1 C313 220P R308 68K C802 0.01 CONTINUE DVD MAIN 2 DVD-DISC-IN DVD-DISC-OUT A 1 STBY 28 2 27 3 26 4 25 5 24 6 23 7 GND 22 DET. AMP R313 10K C311 0.1 C302 820P C421 47P C422 47P C423 47P R302 220 C314 3300P R301 R305 1.5K 1K C301 0.1 C425 47P C426 47P C427 47P C305 6800P DET. AMP R258 180 IC201 SN74LVC1G3157DCKR (SW) 6 0.1 GND VCC 5 3.3 8 VCC C215 0.1 4 0 C318 0.1 9 VCC 20 GND 19 12 13 14 R320 1.5 VCC 21 10 GND 11 C317 0.1 R319 1.5 R818 1K SPINDLE MOTOR DRIVE TRACKING ACTUATOR DRIVE SLED MOTOR DRIVE 18 FOCUS ACTUATOR DRIVE 16 17 R471 100K C316 0.1 1 VCC D 11-16 E CONTINUE DVD MAIN 2 DVD-P-ON DVD-SCLK DVD-SDATA DVD-CS DVD-REMOTE PWRCON RESET CONTINUE DVD MAIN 3 RESET *2 R318 1.5 C 1K 1K 1K 1K 1K 1K C473 0.1 15 R817 1K B R411 R403 R406 R404 R407 R402 C471 0.1 C315 0.1 R317 1.5 C310 0.1 R816 15K R812 15K TO POWER SUPPLY CBA CN901 AV+3.3V LED-CONT DVD-DISC-OUT EV+1.2V EV+1.2V EV+3.3V EV+3.3V EV+3.3V DVD-ON+3.3V DVD-ON+5V EV+9V EV+9V GND GND GND GND GND GND GND PWRCON(NU) DVD-SCLK DVD-CS DVD-DISC-IN DVD-SDATA DVD-REMOTE DVD-P-ON C257 1 Q251 KTC3875SGR-RTK/P (AMP) DISC-OUT SENSOR CBA R315 91K C308 0.039 C250 0.1 C804 0.1 Q804 KTA1504SY-RTK/P (LED DRIVE) C801 0.01 Q253 KTC3875SGR-RTK/P (AMP) C259 1 R255 C253 100/6.3V 560 R252 2.2 0 3 R805 R806 0 0 DISC-IN R268 180 R322 10K 0.3 (0) 1 0 2 R801 R803 4.7K 4.7K IC301 SA5624G (SERVO DRIVE) C303 68P Q252 KTA1504SY-RTK/P (AMP) C233 0.01 R811 10K R265 470 R303 22K Q254 KTA1504SY-RTK/P (AMP) CN301 1 2 3 4 5 R325 1K 6 CN801 LED-POWER 1 DVD-DISC-OUT 2 DVD-DISC-IN 3 GND 4 C263 47 /6.3V R262 2.2 R261 5.6 LOAD-DISC CN5001 1 2 3 4 C202 180P C210 0.1 C203 0.1 CN401 1 2 3 4 C417 C408 5 L401 150P 330/6.3V 0 6 C418 7 L402 0.1 0 8 9 L403 C402 C416 10 0 0.1 0.1 11 12 C405 0.1 13 14 C403 15 0.1 16 17 C412 C411 C410 18 0 0 0 19 20 21 22 23 24 25 26 3 2 1 3 VOUT GND VCC VOUT GND NU NU 5 IC461 4 2 IC462 PST3229NR BMR-110529 (RESET) (RESET) F FL11.11SCDV1 DVD Main 2 Schematic Diagram CONTINUE DVD MAIN 3 FDQ(0~15) CONTINUE DVD MAIN 3 MA(0~10) MDQ(0~15) FADR(0~19) IC101 MN2DS0018VP MICRO CONTROLLER FDQ3 FDQ11 FDQ4 FDQ12 FDQ5 FDQ13 FDQ6 FDQ14 FDQ7 FDQ15 R141 10K 3 FADR16 FADR15 FADR14 FADR13 FADR12 FADR11 FADR10 FADR9 FADR8 FADR19 CONTINUE DVD MAIN 1 DVD-P-ON DVD-SCLK DVD-SDATA DVD-CS DVD-REMOTE PWRCON RESET 72-I1 75-G1 74-H1 76-G1 68-G1 69-G2 70-I1 CONTINUE DVD MAIN 1 DVD-DISC-IN DVD-DISC-OUT 78-H1 79-H1 30-L2 FADR18 FADR17 FADR7 FADR6 FADR5 FADR4 FADR3 FADR2 FADR1 69-G2 R131 10K 68-G2 75-G2 76-G2 EXT MEMORY DATA1 EXT MEMORY EXT MEMORY EXT MEMORY GND VDD(+3.3V) EXT MEMORY EXT MEMORY EXT MEMORY EXT MEMORY EXT MEMORY EXT MEMORY EXT MEMORY EXT MEMORY GND VDD(+3.3V) EXT MEMORY EXT MEMORY GND VDD(+1.2V) EXT ADR16 EXT ADR15 EXT ADR14 EXT ADR13 EXT ADR12 EXT ADR11 EXT ADR10 EXT ADR9 EXT ADR8 EXT ADR19 EXT WE GND VDD(+3.3V) EXT ADR18 EXT ADR17 EXT ADR7 EXT ADR6 EXT ADR5 EXT ADR4 EXT ADR3 EXT ADR2 EXT ADR1 GND VDD(+1.2V) NU PWRCON NU NU DVD-REMOTE NU GND VDD(+3.3V) DVD-SCLK DVD-CS 1 29-L2 26-L2 25-L2 24-L2 MDQ2 MDQ13 MDQ5 MDQ10 MDQ4 MDQ11 MDQ3 MDQ12 MDQ7 MDQ8 MDQ6 MDQ9 MA9 23-L2 20-L2 19-L2 SDRAM DATA1 SDRAM DATA14 SDRAM DATA0 SDRAM DATA15 VDD(+1.2V) GND OSC-OUT OSC-IN VDD(+3.3V) GND DATA9 DATA2 DATA10 EXT MEMORY DATA(0-15) SDRAM DATA(0-15) DATA3 DATA11 DATA4 DATA12 DATA5 DATA13 DATA6 DATA14 SDRAM ADDRESS(0-10) EXTERNAL MEMORY INTERFACE ECC DECODER INTERFACE NU NU NU VDD(+3.3V) STREAM INTERFACE DATA7 DATA15 DSP DECODER I/O PROCESSOR AUDIO INTERFACE DMA INST. ROM BCU 32BIT CPU DATA RAM INST. ROM UMAC GND VDD(+3.3V) VDD(+3.3V) GND DATA RAM INST. ROM DATA RAM GND AUDIO D/A CONVERTER DAC READ MEMORY INTERRUPT CONTROLLER DAC GND COMP2 I-REF1 V-REF COMP1 VDD(+3.3V) TIMER WATCH DOG TIMER VIDEO INTERFACE NTSC/PAL ENCODER CPU INTERFACE DAC DAC DAC CPU INTERFACE SERIAL GENERAL I/O DEBUG BCU INTERRUPT CONTROLLER WATCH DOG TIMER TIMER VDD(+3.3V) FOCUS DRIVE TRACKING DRIVE GND FD-OFST TD-OFST SL-ADS SP-ROT REMOTE CONTROL 32BIT CPU INST. CACHE DATA CACHE RF SIGNAL PROCESS CIRCUIT DVD/CD FORMATTER V-REF(H) 162 161 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 MDQ1 MDQ14 MDQ0 MDQ15 R191 680 R192 1M 66-H1 65-K2 64-K2 C191 15P CONTINUE DVD MAIN 1 LOAD-DISC SP-ROT SL-ADS X101 27MHz C192 22P R195 2.2K C197 100/6.3V C118 0.1 C196 0.1 CONTINUE DVD MAIN 3 DVD-SPDIF DVD-AUDIO(R) DVD-AUDIO-MUTE DVD-AUDIO(L) DVD-Y DVD-Pb DVD-Pr C195 0.1 C623 22P C125 1 R112 15K C120 1 37-G4 38-G4 R114 18K R113 39K C135 4.7 C122 0.1 C329 150P C328 150P R128 430 19-J4 20-J4 22-I4 23-I4 24-I4 25-I4 26-I4 27-I4 28-I4 29-I4 30-G2 31-H4 32-H4 C116 0.1 6-G4 7-G4 64-L4 65-L4 CONTINUE DVD MAIN 3 DQM0 DQM1 DQM3 NWE NCAS NRAS NCSM BA0 BA1 MCK EXT-WE EXT-CE EXT-OE 50-G3 49-G3 48-G3 47-G3 R241 1K R242 1K 34-G4 33-G4 C212 120P L108 2.2uH C226 0.1 C225 0.1 C101 100P G C102 1000P C103 C104 820P 1000P C105 0.1 C106 C107 120P 1000P C108 100P C109 C110 C111 C112 C113 0.1 0.01 150P 0.1 1000P H C114 C115 47P 180P C117 820P C230 C222 0.018 0.1 C231 5600P C211 0.1 C237 0.1 C119 1000P 40-G4 42-G3 41-G4 C223 0.033 43-G3 44-G3 46-G3 45-G3 R291 10K 72-G2 R202 10K 70-G2 74-G2 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 79-G2 53-G3 78-G2 36-G4 66-L4 39-G4 35-G4 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 VDD(+3.3V) GND FDQ1 FDQ9 FDQ2 FDQ10 CONTINUE DVD MAIN 1 EV+1.2V EV+3.3V(D) EV+3.3V(A) 216 215 214 213 212 211 210 209 208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 V-REF-H5 V-REF-L5 6-K2 7-K2 33-K1 34-K1 35-H1 36-H1 37-K2 38-K2 39-H1 40-J1 41-J1 42-J1 43-J1 44-J1 45-J1 46-J1 47-K1 48-K1 49-K1 50-K1 53-H1 EXT MEMORY DATA8 EXT MEMORY DATA0 EXT OE EXT CE EXT ADR0 VDD(+1.2V) GND SDRAM ADDRESS3 SDRAM ADDRESS4 SDRAM ADDRESS2 SDRAM ADDRESS5 VDD(+3.3V) GND SDRAM ADDRESS1 SDRAM ADDRESS6 SDRAM ADDRESS0 SDRAM ADDRESS7 SDRAM ADDRESS10 SDRAM ADDRESS8 SDRAM BA1 VDD(+3.3V) GND SDRAM ADDRESS9 SDRAM BA0 SDRAM DATA MASK3 NU SDRAM CS SDRAM RAS SDRAM CAS VDD(+1.2V) GND SDRAM MCK VDD(+3.3V) SDRAM MCK GND SDRAM WE SDRAM DATA MASK1 SDRAM DATA MASK0 SDRAM DATA7 SDRAM DATA8 SDRAM DATA6 SDRAM DATA9 VDD(+3.3V) GND SDRAM DATA5 SDRAM DATA10 SDRAM DATA4 SDRAM DATA11 SDRAM DATA3 SDRAM DATA12 VDD(+3.3V) GND SDRAM DATA2 SDRAM DATA13 CONTINUE DVD MAIN 1 FD-OFST TD-OFST VREFH VREF165 SLD STBY FOCUS DRIVE TRACKING DRIVE SPDL LPCO1 LPCO2 LPC VIN1RF VIN2RF VIN3RF VIN4RF VIN5 VIN6 VIN7 VIN8 CD/DVD R102 BEAD R101 56 NU DVD-SDATA NU NU NU NU DVD-DISC-OUT CD/DVD DVD-DISC-IN STBY LOAD-DISC SPDL SLD GND VDD(+3.3V) RESET NU NU NU NU NU NU DVD-P-ON NU NU NU NU GND VDD(+1.2V) VDD(+3.3V) PLFIL1 V-REF-H7 GND V-REF-L7 GND CCAPA CDATA VDD(+3.3V) NU NU 4 27-L2 22-L2 32-L2 31-L2 28-L2 MA3 MA4 MA2 MA5 FDQ0 FDQ8 MA1 MA6 MA0 MA7 MA10 MA8 FADR0 C239 0.1 C128 0.1 C130 0.1 C131 0.1 C136 330/6.3V C123 220/6.3V C134 220P C214 560P DVD MAIN CBA UNIT I J 11-17 K L FL11.11SCDV2 2- 11M2 M2 MA5 MA4 MA7 MA6 MA8 MA9 MDQ8 MDQ9 MDQ10 MDQ12 MDQ11 MDQ13 MDQ14 MDQ15 DVD Main 3 Schematic Diagram DVD MAIN CBA UNIT 3M2 R510 47K 4 C501 0.1 C502 180P C503 150P C504 220P C505 100P C506 0.1 C513 100P C514 680P A4 VSS VDD A5 A3 A6 A8 A9 BA1 A7 NU UDQM BA0 CKE RAS CS CLK CAS NU UDQM A10/AP A2 A1 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 A0 9 WE LDQM 8 VDD 7 DQ7 6 DQ6 DQ5 5 VSSQ VDDQ 4 DQ4 DQ1 3 DQ3 VDQD 2 DQ2 DQ0 1 VSSQ VDD IC503 EM638165TSA-6G (SDRAM) L501 0 3 VSS DQ8 DQ9 VDDQ VSSQ DQ10 DQ11 DQ12 VDDQ DQ13 DQ14 VSSQ VSS DQ15 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 MA3 MA2 MA1 MA0 MA10 MDQ7 MDQ6 MDQ5 MDQ4 MDQ3 MDQ2 MDQ0 MDQ1 1- 5- 6- 7- 8- 9- 10M2 M2 M2 M2 M2 M2 M2 CONTINUE DVD MAIN 2 MA(0~10) MDQ(0~15) CONTINUE DVD MAIN 2 FDQ(0~15) FADR(0~19) IC103 MX29LV160DBTI-70G (FLASH ROM) CONTINUE DVD MAIN 1 EV+3.3V(D) 2 CONTINUE DVD MAIN 2 DQM0 DQM1 DQM3 NWE NCAS NRAS NCSM BA0 BA1 MCK EXT-WE EXT-CE EXT-OE 1-O3 2-O4 3-O4 5-O3 6-O3 7-O3 8-O3 9-O3 10-O3 11-O4 FADR15 1 A15 A16 48 FADR14 2 A14 BYTE 47 FADR13 3 A13 VSS 46 FADR12 4 A12 DQ15/A-1 45 FADR11 5 A11 DQ7 44 FDQ7 FADR10 6 A10 DQ14 43 FDQ14 FADR9 7 A9 DQ6 42 FDQ6 FADR8 8 A8 DQ13 41 FDQ13 FDQ15 R106 L104 R611 2.2K DQ5 40 FDQ5 FDQ12 11 WE DQ4 38 FDQ4 12 RP VCC 37 13 NU DQ11 36 FDQ11 14 NU DQ3 35 FDQ3 15 NU DQ10 34 FDQ10 L614 BEAD FADR18 16 A18 DQ2 33 FDQ2 L613 BEAD FADR17 17 A17 DQ9 32 FDQ9 FADR7 18 A7 DQ1 31 FDQ1 9 A19 10 NU FADR6 19 A6 DQ8 30 FADR5 20 A5 DQ0 29 FADR4 21 A4 OE 28 FADR3 22 A3 VSS 27 FADR2 23 A2 CE 26 FADR1 24 A1 A0 25 L612 BEAD C620 22P FDQ8 C613 22P FDQ0 C612 0 R565 47 R567 47 C610 0.01 L618 0 CN601 4 5 6 7 8 9 10 11 12 13 14 15 16 TO POWER SUPPLY CBA CN902 DVD-Pr GND DVD-Pb GND DVD-Y GND GND GND DVD-AUDIO(L) DVD-AUDIO-MUTE DVD-AUDIO(R) GND DVD-SPDIF C608 22P R604 0.1 N CONTINUE DVD MAIN 2 DVD-SPDIF DVD-AUDIO(R) DVD-AUDIO-MUTE DVD-AUDIO(L) DVD-Y DVD-Pb DVD-Pr BEAD R623 0 R624 0 R621 0 C561 0.1 FADR0 M 300 DQ12 39 FADR19 CONTINUE DVD MAIN 1 RESET 1 FADR16 O P 11-18 Q C603 100P C604 100P C625 0.1 R604 0.1 R FL11.11SCDV3 Power Supply CBA & Jack CBA Top View CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. J241 GND J240 R821 R672 J163 LCD -6V J299 BL-SW 14 CN201 15 J309 1 J286 GND 2 C612 R615 D609 D646 C644 D641 D902 GND J223 GND J307 PROTECT3 J303 BL-ADJ J288 C692 C611 Q601 D662 GND J227 Q871 JK733 Q873 6.7V D421 J232 J233 COMP-Pr J229 A-OUT-MUTE Q874 C609 R613 D643 ALL6V J231 J236 PROTECT1 J341 P-ON-H2 C650 COMP-Pb / BLUE LCD 16V J235 Q204 P-ON 3.3V LCD 16V C220 C675 R618 D633 C642 LOW-VOL PROTECT J238 P-ON 3.3V D411 Q602 T601 D644 D661 P-ON 3.3V J234 BC601 D657 JK732 J230 VT 31V D634 D647 J237 COMP-Y J332 J226 J222 S-Y J225 J224 GND GND V-R V-L R763 GND C645 D655 R671 J242 D612 D606 D5.5V 9 1 J228 J245 R670 D674 R611 C613 FG R616 D607 C634 3.5Vfor1.8V D640 D909 D903 R606 J335 R210 J297 GND J284 R653 J274 J273 D652 D608 C633 J246 D610 C610 R610 R661 R931 D908 J239 GND J243 DVD-LED J244 KEY-IN2 J331 J338 / GREEN Q206 J306 J301 VGH Q203 J312 J291 GND C646 Q631 D638 J262 R242 D635 D209 IC601 D632 J253 R212 GND Q202 GND Q212 R650 C637 C632 Q211 R243 J281 36V R637 D639 D631 LCD -6V J256 3.5Vfor1.8V C219 C210 Q205 R203 C204 R249 J314 D205 R638 D651 D650 R639 C638 J276 36V J324 C222 C631 D653 D611 A-MUTE KEY-IN2 D206 R238 R239 D419 Q209 R646 J263 DVD-LED J254 J251 J320 D202 Q210 J337 C223 R237 GND J296 C643 GND J305 Q644 D416 J293 J290 D211 D204 D649 D648 R645 R614 C647 J249 P-ON 5V Q634 C501 36V C224 D5.5V R245 R236 GND R235 36V Q207 R229 LCD 16V J302 J300 R228 J336 RESET J298 LCD 24V J292 LCD -6V D404 JS202 OE2 R224 D420 R240 R223 J315 D207 D401 R405 Q401 J265 D664 ALL3.3V IC631 J261 LCD 16V GND J255 J264 JS101 D413 J252 Q905 D901 J250 R914 C910 D408 R930 J339 J257 MOTOR 10V GND J259 PROTECT1 25 D904 J267 JS201 R244 R912 26 J325 C916 R913 C648 D403 J329 J278 LOW-VOL PROTECT GND J269 GND JK731 L951 CL701A J221 ALL6V R204 D412 J334 3 J280 A Q201 R501 J272 C951 J E234498 ALL6V R697 R915 A01F0MPW JS102 IC901 R917 J248 DVD-LED J247 KEY-IN2 D667 BA94F0F0102 6 D675 D210 J327 C911 R636 J326 J275 D5.5V 4 R909 D406 2 CN901 J270 P-ON 5V J268 R227 D637 R695 R696 J271 Q902 R409 J308 D673 Q208 Q501 ALL3.3V Q901 GND J260 DVD-SDATA J258 REMOTE-OUT J316 R665 Q635 J304 PROTECT2 D660 J287 C912 1 J285 DVD 3.3V TOOL NO. D907 D203 D405 C918 10 J313 LCD 16V R666 Q636 D208 RESET D402 C917 R667 GND GND J289 R925 R407 J310 Q633 L901 Q903 J318 GND R684 R919 R927 C919 Q904 R920 D5.5V J294 J311 D407 A3 RESET Q402 R924 R929 R926 1 2 3 4 5 6 7 8 9 R660 D659 R923 R922 D905 C7A3 J319 J295 GND 13 R663 R662 R664 1 D658 D906 JK752 JK751 12 R698 / RED JK754 B / WHITE JK753 R921 / YELLOW J317 GND CN902 R928 9 CL701B C225 NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. 2 1 BA94F0F0102 6 4A/125V Power Supply CBA Jack CBA CAUTION ! : For continued protection against risk of fire, replace only with same type 4 A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V. R247 Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing. Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required. D642 R605 JS631 5.5Vfor3.3V J208 R674 GND D620 J150 B GND 07 R6 BC803 HOT TM601 /WHITE C693 CN801 E TM602 GND C827 J322 GND AC601 J328 D802 D801 J105 J104 J107 AMP 13V J106 GND C694 L804 03 BC805 D803 D 11-19 SA601 C602 FH601 GND C832 C816 D807 J116 GND VCCA J112 J111 GND BC804 CN802 D804 R6 GND GND R819 J125 J128 GND J114 J109 KEY-IN2 L601 J136 AMP-MUTE F601 GND 01 ERROR J323 J142 A-MUTE D418 J140 C819 ALL3.3V R175 Q171 C814 COLD BC802 J144 AMP 13V J149 FH602 D601 C601 J330 C603 D806 J123 C /RED C655 J164 C653 D645 L602 4A/125V C605 C823 CN601 L8 A CN602 C604 GND BC801 L802 J143 J145 GND GND J127 J101 GND /BLACK RISK OF FIREREPLACE FUSE AS MARKED D602 D603 GND J176 GND R685 R683 R682 Q641 Q640 C652 J161 Q801 D409 Q802 D417 J110 DVD-LED P-ON 3.3V R402 J137 PROTECT2 ALL3.3V J130 J340 J139 PROTECT3 C676 J172 D666 C656 GND J153 ALL3.3V C654 GND BC841 Q841 JS138 J103 GND Q639 R673 R677 R691 J171 Q643 R693 R694 D670 R687 TUNER 5V D414 Q172 ALL3.3V J102 CN101 J135 3.5Vfor1.8V P-ON-H1 KEY-IN1 J117 J118 BL-ADJ VCOM-PWM J122 J121 OE2 J119 J120 BL-SW GND J132 GND J131 6.7V J115 J108 P-ON 3.3V GND J113 R699 R700 D676 8 J197 AMP 13V R602 D415 C657 Q642 P-ON 5V J159 J151 J134 PROTECT1 J133 P-ON-H2 J129 GND J126 3.5Vfor1.8V P-ON 5V J124 J141 GND 28 CN301 J207 R692 L871 D671 JK711 / WHITE SPDIF J343 J160 L801 / RED C691 C639 AMP 13V R678 J147 / ORANGE J198 R686 D604 C844 TU301 29 Q638 Q872 6.7V J155 TUNER A S 1 R603 AOUT-R J157 JK722 D621 Q637 GND R688 JK841 R604 R617 P-ON 3.3V J174 D303 1 J206 JK741 GND GND D665 J196 J169 HDMI-R J170 HDMI-L J168 P-ON 9V L301 J156 GND 28 J152 AOUT-L J186 J166 TUNER 5V 29 J146 2 1 KEY-IN1 RESET J148 / RED / RED TUNER 5V JS302 R878 J195 SW 9V D302 J158 JS301 J191 D410 JK721 C303 J154 J342 C306 JS303 D301 GND CN302 GND J194 J188 JK742 JS304 J162 J165 VT 31V J167 SPDIF C640 J202 PROTECT1 C880 J184 J180 PC-R BC301 2 2 J212 6.7V R689 R781 J192 PC-L J333 J219 MOTOR 10V AMP 13V LCD 16V J204 J189 A-OUT-R JK872 R780 J187 SW 9V Q772 J173 GND Q771 R771 GND 29 28 J181 J178 INPUT1 J175 INPUT0 1 J179 SEL-R GND GND J177 J199 CN303 J185 J182 J215 J211 OPAMP 9V J183 J210 C771 J218 GND OPAMP 9V R788 R791 / WHITE JK871 J200 GND HDMI-L GND J203 J216 COMP-L J213 A-OUT-L / WHITE J205 J209 SEL-L V-R J214 V-L 2 J217 A-MUTE J190 R790 1 / RED F G / BLACK BA94F0F01026 Power Supply CBA & Jack CBA Bottom View C902 R902 R903 C903 R901 C901 C752 R756 R758 C751 R757 C753 R760 R753 R759 R755 JK754 C919 R927 R921 JK751 R751 JK752 C914 C917 Q904 R907 C906 L901 Q633 R406 J308 R407 C905 R908 R920 J318 GND Q903 C907 C904 R905 R919 R904 R906 R684 Q635 R665 C402 Q401 D420 R225 Q207 R226 D211 R910 R911 J326 R636 D648 D649 R231 D204 D406 D405 2 CN901 J285 DVD 3.3V 1 C915 C912 C913 D402 D404 J298 LCD 24V J292 LCD -6V J302 J300 Q501 J290 J293 Q209 R658 D650 R649 R647 C643 J296 J295 Q644 D416 LCD 16V GND GND R644 D419 J305 R229 R228 J336 RESET 36V R237 R238 R239 C223 D205 D206 J297 J291 GND R652 C646 Q631 R648 D651 R638 C208 J312 J301 VGH Q206 J306 LCD 16V C220 R210 C217 R659 R918 R912 C911 J327 R411 R668 R247 C638 R639 C222 R234 R233 R232 J276 36V J324 C501 C221 R412 R637 R650 36V J281 D652 J273 J274 R653 C675 J288 C692 GND J284 C203 Q204 P-ON 3.3V C909 C908 R669 D664 26 R916 25 C957 C952 R957 R951 R954 C955 J339 C910 R914 R959 D901 R244 D609 C953 R953 C959 J250 Q905 R930 C647 J249 P-ON 5V J252 GND J255 LCD 16V J261 PROTECT1 R403 R681 R410 R241 R613 D611 R242 D635 R616 FG J262 D638 D209 R243 Q211 C632 C637 D210 J265 ALL3.3V IC631 J325 4 C613 R611 Q602 C609 R615 C612 T601 R958 J331 C954 C958 C960 R960 J338 J334 C956 R956 R952 R955 D908 J239 GND J243 DVD-LED J244 KEY-IN2 R734 C731 R731 D657 R401 BC601 J241 GND J230 VT 31V R893 R888 J234 R735 C732 LCD 16V C650 C736 P-ON 3.3V R887 R732 C734 C735 1 R651 C611 J226 J225 J224 GND V-R Q873 V-L J332 J232 R672 R736 R877 JK733 R606 R614 1 2 R779 R778 R790 R791 C776 R745 R743 R777 C775 J206 J207 CN303 R774 Q772 J196 C744 R884 C878 GND J181 28 C883 D665 Q638 R775 J179 29 Q771 R771 1 R772 J192 PC-L R773 J180 PC-R J171 R691 D671 C657 Q642 R302 R303 C309 J165 VT 31V D301 CN302 GND D302 R845 R711 C721 C723 R310 JS304 L301 R723 R721 JK711 R848 C656 R846 J161 C653 J154 C305 C308 J145 GND 1 2 P-ON 5V J124 J126 3.5Vfor1.8V J129 GND J141 GND J113 GND R700 C683 J115 J117 R811 BC803 CN301 R699 JS138 R173 C693 28 29 J102 ALL3.3V J103 GND R174 Q171 J112 J111 GND J109 KEY-IN2 R815 C837 R816 C815 C816 D807 J107 AMP 13V J106 GND C845 D804 D801 J105 J104 C828 C846 C821 C824 C820 C829 C825 C826 C822 C833 R812 C817 J116 GND C818 VCCA R171 J108 P-ON 3.3V C682 J119 6.7V J120 J131 J121 J132 OE2 GND BL-SW GND BL-ADJ J122 KEY-IN1 J118 R172 ALL3.3V R175 J340 C684 VCOM-PWM J130 P-ON-H1 J135 3.5Vfor1.8V J139 PROTECT3 ALL3.3V J137 R807 GND F601 J323 C834 C836 R819 R801 C801 R814 R813 J125 PROTECT2 J110 DVD-LED C835 D418 R803 C806 C805 C804 C807 C808 J142 A-MUTE C803 R804 R802 C802 C809 J143 J144 P-ON 3.3V R402 J134 PROTECT1 J133 P-ON-H2 C302 C301 R301 C307 L302 C310 R308 L303 C311 C681 J146 29 KEY-IN1 RESET J148 R809 C813 R808 BC801 C810 R805 R806 BC802 C811 07 R6 FH602 1 SA60 C601 L601 COLD R817 R722 J151 28 J152 GND R305 R307 J343 SPDIF R726 R844 R842 C842 C843 Q841 R841 R724 R818 R690 BC841 R847 C841 C722 R654 Q801 C847 R408 GND J330 R820 C654 D415 D645 R642 R643 R641 C655 J164 R687 D670 R795 C703 C704 C702 R716 R714 R712 R694 R693 Q643 C652 R685 R683 R682 Q641 Q640 GND C651 R680 J172 2 R715 C701 R713 J169 HDMI-R J170 HDMI-L R781 C742 R746 C676 D603 R692 R872 C874 C876 R892 R880 C885 L871 R876 R874 C872 R785 R782 R673 R677 D602 R675 R676 Q639 R679 D666 R882 R886 Q872 R744 R742 R780 GND J199 J177 C772 J187 SW 9V R787 R784 R878 JK741 R741 JK871 J200 C871 HDMI-L J195 R792 R871 C879 R881 IC871 OPAMP 9V J183 J210 R873 C873 GND GND R674 J208 C641 5.5Vfor3.3V JS631 SW 9V R776 J205 V-R J214 V-L R794 R793 R788 R789 C773 C743 C741 R875 C875 R891 R883 R879 C884 OPAMP 9V C882 R885 C877 R605 CN602 FH601 CN101 R752 C755 C757 R761 C761 C758 R762 C762 R754 C754 C756 R698 R662 D658 R664 R663 R660 R409 J316 R405 R240 R223 R224 J314 GND Q212 C207 R206 R205 Q202 R207 C209 R222 Q203 R211 R208 2 01 R6 4A/125V D676 C830 C838 03 L8 D802 C839 GND J328 BA94F0F01026 11-20 A B C D 8 1 GND R304 R309 R306 J342 R311 WF6 PIN 19 OF CN302 BC805 D803 L804 GND J317 GND R404 D401 D207 J315 R202 J337 Q210 GND JS202 OE2 R235 R236 R245 R248 GND R212 C212 R209 14 CN201 15 1 J286 GND 44 IC801 23 J101 BC804 Q172 C832 CN802 J322 GND CN801 C225 C206 R249 C216 R213 R215 R214 C214 C213 C210 C202 C215 C201 J299 C694 R810 HOT 1 J127 GND 22 J128 GND D303 WF5 PIN 17 OF CN302 GND TUNER S A C819 ERROR J136 AMP-MUTE D414 TU301 AC601 C827 CN601 R201 J320 D202 R203 C204 R219 Q205 R218 R217 C218 R216 C219 J163 GND J307 PROTECT3 J303 BL-ADJ J309 BL-SW J140 GND JK722 WF4 PIN 15 OF CN302 D417 C814 L801 AMP 13V J149 J156 JS301 JK841 C304 J147 L802 D806 J157 C724 JS302 TUNER 5V R843 J158 WF7 PIN 13 OF CN302 D601 J159 C844 GND J155 J153 ALL3.3V D409 Q802 GND C603 JS303 J160 BC301 WF2 PIN 8 OF CN302 R725 D604 R786 P-ON 5V TUNER 5V C823 L602 J162 GND C306 C605 J173 GND J333 JK742 C303 JK721 J178 INPUT1 J175 INPUT0 R689 J167 SPDIF J150 J184 AOUT-R D410 J174 6.7V J221 WF3 PIN 6 OF CN302 R688 J176 GND D620 Q637 J168 P-ON 9V R602 GND R678 J197 AMP 13V 16 9 J203 WF1 PIN 4 OF CN302 J185 SEL-R J182 GND R783 JK872 J189 A-OUT-R 8 5 J186 GND AMP 13V C639 C880 J194 J209 GND C771 R617 J191 P-ON 3.3V R603 GND 1 IC771 C640 AOUT-L 1 8 J211 LCD 16V 4 J204 PROTECT1 J202 D621 J217 A-MUTE J190 SEL-L J216 COMP-L J213 A-OUT-L J212 6.7V R604 GND J123 J114 C602 4A/125V 3 R733 8 IC951 GND D903 D909 J218 GND MOTOR 10V J219 J215 AMP 13V GND J228 D641 5 J222 S-Y J223 Q871 J227 GND D902 GND D642 R763 C733 D421 C644 J235 J231 6.7V R926 LCD -6V D662 Q902 R917 CL701A D411 P-ON 3.3V R821 J240 ALL6V J233 COMP-Pr J229 A-OUT-MUTE Q874 D640 J188 R686 J198 C691 E F G D412 L951 J335 JK732 J238 COMP-Pb J236 PROTECT1 J341 P-ON-H2 D646 J237 COMP-Y D643 J166 TUNER 5V GND C604 D655 9 D661 Q601 R671 D644 D674 J242 LOW-VOL PROTECT C642 D633 R931 D647 R618 J246 3.5Vfor1.8V D904 J248 DVD-LED J247 KEY-IN2 C634 R670 C645 D634 J245 D5.5V D606 R913 1 4 D612 J251 J268 R909 D413 J253 C951 C633 Q901 JK753 R915 R610 R923 1 CL701B 9 J260 DVD-SDATA J258 REMOTE-OUT J257 MOTOR 10V JS101 DVD-LED C916 J264 C918 D907 J287 ALL3.3V D637 GND IC901 J272 JK731 R661 D607 KEY-IN2 3.5Vfor1.8V D608 J280 D408 J254 A-MUTE D632 J259 D5.5V J263 C648 J267 C224 36V IC601 R666 R924 J271 R697 JS102 ALL6V J329 ALL6V J275 D5.5V D667 GND J278 LOW-VOL PROTECT GND J269 D639 LCD -6V J256 C610 R645 GND D631 D610 D653 C631 J270 P-ON 5V R501 R646 R696 Q634 Q636 R227 R695 D403 D673 GND J310 R667 R925 D660 R929 D5.5V J294 GND J289 J304 PROTECT2 D675 J311 RESET D407 J313 LCD 16V Q208 R221 R204 8 5 JS201 Q402 D906 1 13 R922 IC201 J319 D905 R220 D659 RESET D208 R928 Q201 D203 1 4 Jack CBA Power Supply CBA NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. 2 CN902 12 CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. WF10 PIN 1 OF CN902 WF9 PIN 3 OF CN902 WF11 WF8 PIN 9 OF PIN 5 OF CN902 CN902 WF12 PIN 11 OF CN902 WF13 PIN 13 OF CN902 CAUTION ! : For continued protection against risk of fire, replace only with same type 4 A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V. Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing. Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required. Inverter CBA, Function CBA & IR Sensor CBA Top View Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing. Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required. NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. C1065 A3 C1115 CN101 D 6 7 8 9 10 J103 CL103A BA01F4F0103 2 CN1150 C1111 C1061 CL102A CL101B C101 C7A3 C CL102B BA01F4F0103 2 D106 TOOL NO. 1 2 3 4 5 D105 STD BY SW101A CN1100 CN1050 CL103C GND R124 D104 C113 A3 D101 Not Used STB BY J102 STOP R123 CL103B J101 SW151 SW152 R154 EJECT R108 DVD C7A3 RS101 R127 SW153 C151 POWER D151 SW101B R153 / / RED ORANGE R128 SW103A CH UP MENU VOL DOWN SW104A CH DOWN SW106A VOL UP SW107A R152 R111 POWER C108 R109 R112 R114 SW105A RS102 D107 MENU R113 B / GREEN POWER PATTERN CH UP R115 BA01F4F0103 2 C7A3/A3 SW103B CH DOWN PLAY VOL DOWN SW154 SW104B R151 SW105B R155 D SW155 AGING SW106B R156 SW107B VOL UP Not Used Not Used IR Sensor CBA R101 Function CBA CN1200 C1165 C1161 C1211 C1215 C C1216 C1212 C1166 C1162 C1116 C1112 C1062 C1066 A01F0MIV J E234498 J1122 C1205 J1123 BC1501 BC1500 J1102 J1101 J1097 GND J1084 J1082 R19 1 2 D1051 D10 50 0 R1944 J1067 Q1930 J1068 C1931 J1059 R1937 J1054 J1052 D1930 J1026 2 J1071 J1008 5 CN1005 11 J1075 1 IC 10 GND J1061 J1022 J1063 R1940 Q1931 R1930 R1942 Q1932 R1932 C1910 CN1900 19 J1131 R1933 R1941 R1934 D1970 GND 31 R1931 FG C1970 D1972 C1934 J1121 30 19 IC Q1970 4 J1045 FG D1934 D1935 C1933 R1939 D1933 D1931 R1935 C1932 R1936 D1932 3 R1967 R1968 R1987 Q1971 CN1001 15 J1002 5 90 C1 C1982 1 J1001 D1973 Q1972 D1002 GND R1969 C1983 14 R1970 R1971 R1983 GND BC1301 J1021 GND BL-SW J1016 D1971 J1019 R1035 R1019 R1036 J1018 PANEL+13V J1007 BL-ADJ. R1040 R1045 J1027 BL-SW 2 R1984 C1992 J1043 J1132 GND J1028 GND J1029 GND J1041 Q1803 R1803 D1630 10 CN1003 11 R1945 BC1930 93 R1989 EER35 T1950 D1040 R1991 D1940 BC1551 BC1550 D1220 Q1161 D1801 D1960 47 46 48 GND J1081 R19 GND J1083 GND C1051 J1079 C1050 J1090 J1091 J1080 R19 J1096 J1095 D1500 J1100 J1109 J1107 J1108 J1106 J1105 D1550 J1099 J1098 J1087 J1086 J1077 R1050 J1076 J1089 J1088 D1218 D1217 D1224 D1223 D1222 J1066 D1168 Q1804 D1171 R1812 Q1801 J1012 PROTECT3 J1005 R1805 D1701 D1703 D1702 D1700 Q1004 C1801 C1800 2 Q1005 R1804 J1004 GND J1032 J1134 R1502 R1503 R1044 R1943 C1990 Q1815 J1009 Q1621 1 R1171 J1013 Q1802 Q1800 J1015 Q1600 J1014 Q1503 D1172 R1810 J1033 GND D1961 HOT Q1500 D1990 J1136 D1173 J1025 J1017 J1006 J1011 J1030 J1034 R1504 Q1553 D1161 J1023 J1038 A3 R1990 GND VREF D1802 VREF J1049 J1042 J1020 D1164 J1037 6 BC1931 J1058 D1169 J1040 D1163 J1044 C1053 C7A3 90 D1994 D1174 D1160 R1018 C1000 J1035 GND R1554 VREF J1036 GND Q1501 J1051 D1162 A C1 C1167 J1053 J1003 J1039 Q1502 D1167 J1055 R1811 D1004 D1001 VREF J1047 J1056 R1165 D1165 J1010 J1046 R1121 D1005 BA01F4F0103 2 C1 J1135 D1122 Q1160 GND J1048 C1500 D1166 D1121 C1012 Q1551 GND T1200 COLD C1550 D1170 J1062 J1060 C1056 R1988 D1120 J1072 J1057 J1050 R1032 R1021 Q1001 GND R1051 Q1550 J1064 C1163 R1552 J1065 GND C1117 D1214 C1217 C1009 R1553 D1221 D1124 D1118 D1119 D1116 J1069 Q1111 D1114 J1070 D1006 Q1552 C1204 D1216 Q1211 R1221 D1110 J1073 D1111 D1113 J1074 T1150 C1940 C1213 D1219 R1006 R1043 J1031 D1212 D1211 R1041 D1000 D1123 D1003 J1085 D1112 D1070 Q1061 Q1110 Q1003 GND GND D1213 D1215 R1215 D1210 J1078 C1067 C1113 A J1112 R1550 R1501 Q1210 D1117 B J1127 J1125 J1104 C1052 J1093 R1551 GND J1094 D1068 D1069 D1072 R1071 R1115 D1067 J1120 D1074 D1073 D1065 R1065 D1066 D1071 C1063 J1103 J1110 T1100 GND Q1060 T1050 D1064 J1111 R1005 D1060 D1115 J1128 J1129 D1063 D1062 D1061 J1124 C1054 GND J1126 C1055 J1113 6 Inverter CBA 11-21 BA01F4F01032 Inverter CBA, Function CBA & IR Sensor CBA Bottom View R156 AGING D151 R155 POWER C151 CL103B R123 C110 GND C104 R113 R151 D107 C108 C114 VOL DOWN VOL UP MENU CH DOWN CH UP EJECT STOP PLAY J102 POWER R128 R127 C115 R126 C102 C103 R102 R101 CL103A R124 C111 C112 R125 CL103C CL101B R103 C105 C1062 C1112 C1116 C1162 C1166 C1212 C1054 J1124 J1125 J1126 J1127 BC1500 BC1501 J1123 J1122 C1205 D1062 D1063 J1105 J1106 J1107 J1108 R1060 GND R1063 R1065 D1065 R1062 D1073 D1074 D1067 D1068 J1093 C1068 R1061 D1064 R1114 R1115 R1064 C1064 D1071 D1211 D1212 D1217 J1088 D1218 D1115 R1113 Q1110 C1114 Q1061 D1070 D1112 R1110 R1214 C1214 C1940 J1081 J1080 R1050 J1077 J1076 J1085 J1089 R1072 R1071 R1070 R1069 C1072 R1066 R1551 R1215 D1215 R1213 D1213 R1211 R1210 GND GND D1069 D1072 R1067 R1501 J1086 J1087 C1050 J1090 J1091 GND GND GND J1083 C1051 J1079 GND J1084 J1082 R1500 R1212 GND J1094 J1120 R1068 Q1060 J1098 J1099 D1550 D1500 J1096 J1095 J1097 J1100 J1109 J1101 R1550 C1052 J1104 J1103 J1111 J1110 D1060 J1102 48 R19 46 R19 47 R19 R1031 C1011 R1030 D1123 R1112 D1113 J1073 D1111 D1110 R1008 D1114 R1111 R1007 C1004 R1009 D1116 Q1111 C1117 R1116 Q1001 R1081 R1028 R1080 J1050 R1032 R1021 C1008 R1012 J1072 C1040 R1042 C1118 R1120 R1117 D1120 R1011 R1010 R1025 C1005 J1057 R1015 R1119 R1118 D1118 D1119 D1124 R1221 R1219 C1218 R1220 R1167 R1222 R1216 D1220 J1066 C1222 GND J1065 D1221 R1218 R1217 D1222 D1219 D1223 D1224 BC1550 BC1551 50 D10 D1051 D1040 11 D1170 D1122 R1166 R1169 D1166 R1168 R1172 C1172 C1168 R1170 R1945 T1950 EER35 D1940 R1991 R1989 10 R1023 R1027 R1026 D1004 D1001 R1020 R1014 R1022 C1164 R1164 D1167 D1168 Q1161 C1007 R1017 R1016 C1010 C1006 C1012 R1122 J1047 VREF C1003 R1002 IC1000 R1018 D1160 R1163 R1162 C1122 R1171 C1002 J1049 VREF R1506 C1001 C1703 C1551 R1554 Q1552 C1501 Q1551 Q1501 Q1553 J1011 GND BC1301 R1988 Q1502 R1503 R1502 R1556 J1134 C1552 C1600 R1621 R1620 C1620 J1136 R1631 R1630 D1002 R1804 J1004 R1805 Q1815 D1701 D1703 D1702 D1700 R1700 J1032 R1555 R1600 J1006 R1601 C1601 Q1600 C1702 J1014 IC1700 R1033 R1800 R1029 R1019 R1035 R1036 J1019 J1018 PANEL+13V BL-SW J1016 GND J1021 R1976 R1968 R1977 R1967 GND R1974 D1970 D1972 C1802 R1811 J1015 D1172 R1810 Q1802 Q1800 R1809 R1808 R1701 Q1503 J1030 R1001 R1504 C1502 R1505 D1173 D1161 R1160 D1802 R1812 J1135 Q1801 R1807 D1801 J1027 BL-SW R1045 R1040 R1983 R1980 C1970 R1979 Q1970 C1934 J1121 FG R1931 Q1931 R1930 R1940 R1941 R1942 Q1932 D1930 R1937 J1034 J1042 R1003 C1013 D1163 Q1804 D1171 Q1803 C1014 R1034 R1934 R1975 R1984 R1972 J1043 R1973 C1992 J1041 J1054 J1052 D1935 D1932 J1028 GND J1029 GND J1132 GND R1802 R1806 D1174 R1936 C1932 R1935 D1931 C1933 R1939 D1933 C1931 J1059 J1010 Q1972 C1983 R1986 C1982 Q1971 J1131 J1008 R1982 C1981 R1981 J1075 J1071 BA01F4F01032 11-22 C1800 14 8 1 2 D1630 3 4 5 6 CN1001 15 J1002 1 J1001 Q1621 GND 1 R1552 J1009 R1801 GND J1005 IC R1803 CN1005 CL102B 1 2 CN1003 GND J1022 2 2 J1013 D1973 J1007 BL-ADJ. 31 R1553 GND J1033 C1801 J1023 16 9 A 7 J1025 C1000 R1004 30 8 D1003 J1069 GND 1 J1035 GND J1017 Q1004 19 R1024 J1031 5 14 R1987 CN1900 90 J1045 J1026 D1971 J1061 R1970 C1 J1048 R1161 D1162 J1044 J1040 J1036 J1037 J1038 R1971 Q1005 R1969 FG VREF J1003 R1013 J1020 1 VREF J1039 D1164 R1933 R1932 R1165 C1163 J1051 D1165 J1053 C1167 D1934 C1009 R1121 J1062 J1060 Q1160 D1006 GND J1046 GND J1064 R1043 C1217 J1113 C1055 B J1070 D1214 D1005 J1055 D1169 GND D1990 C1910 D1117 Q1211 C1067 Q1003 Q1500 J1056 J1058 C1990 C1213 J1078 D1061 J1129 C1063 D1066 J1074 BC1931 R1006 D1216 D1121 Q1930 R1005 D1000 C1056 J1128 C1113 C1500 R1990 D1210 D1960 J1067 D1994 J1068 Q1550 R1044 BC1930 C1 93 0 R1944 19 11 6 C1550 R1943 R106 J103 CN101 C1 R1041 HOT Q1210 R1051 90 D1961 J1012 PROTECT3 10 COLD C1053 T1100 T1150 C1065 C1111 T1050 T1200 IC J1063 CL102A C1216 J1112 CN1050 CN1100 CN1150 CN1200 C1061 C1115 C1161 C1165 C1211 C1215 SW107A SW106A R114 SW105A SW104A SW103A SW153 R154 GND C1204 GND C101 SW101B D104 SW152 D PATTERN MENU R109 R152 R112 R111 R153 R108 C113 SW151 J101 SW101A R115 STD BY D105 D106 SW105B SW154 SW104B SW103B RS101 RS102 SW107B SW106B SW155 VOL UP VOL DOWN CH UP CH DOWN POWER DVD STB BY Function CBA IR Sensor CBA Not Used Not Used Not Used D101 Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing. Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required. NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal. H.V. CAUTION C1066 C Inverter CBA WAVEFORMS WF1 ~ WF7 = Waveforms to be observed at Waveform check points. (Shown in Schematic Diagram.) Input: NTSC Color Bar Signal (with 1kHz Audio Signal) WF1 Pin 4 of CN302 CVBS WF2 0.2V WF6 20µs 0.2V 20µs AUDIO 0.2V 20µs Pin 19 of CN302 VIDEO-Pr WF7 0.2V Pin 17 of CN302 VIDEO-Pb Pin 6 of CN302 S-VIDEO-C WF4 20µs Pin 8 of CN302 S-VIDEO-Y WF3 WF5 0.2V 20µs Pin 13 of CN302 0.1V 0.5ms Pin 15 of CN302 VIDEO-Y 0.2V 20µs 12-1 FL11.11WF1 WF8 ~ WF13 = Waveforms to be observed at Waveform check points. (Shown in Schematic Diagram.) Input: NTSC Color Bar Signal (with 1kHz Audio Signal) DVD Video (Play MODE) WF8 DVD-Y WF9 DVD-Pb WF10 DVD-Pr Pin 5 of CN902 0.5V WF11 DVD-AUDIO(L) 20µs Pin 3 of CN902 0.5V WF12 WF13 20µs 0.5ms 0.5V 0.5ms Pin 13 of CN902 DVD-SPDIF 12-2 0.5V Pin 11 of CN902 DVD-AUDIO(R) 20µs Pin 1 of CN902 0.5V Pin 9 of CN902 1V 0.1µs FL11.11WF2 AC601 AC CORD AUDIO(R) -OUT AUDIO(L) -OUT DIGITAL AUDIO-OUT (COAXIAL) HDMIAUDIO(R)-IN HDMIAUDIO(L)-IN COMPONENTAUDIO(R)-IN COMPONENTAUDIO(L)-IN COMPONENT -Pr-IN COMPONENT -Pb-IN COMPONENT -Y-IN CN3006 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 CN302 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 GND SPDIF GND VIDEO-IN S-VIDEO-SW S-VIDEO-C-IN GND S-VIDEO-Y-IN GND INPUT1 AUDIO(R) INPUT0 AUDIO(L) GND COM-VIDEO-Y-IN GND COM-VIDEO-Pb-IN GND COM-VIDEO-Pr-IN AUDIO-MUTE SDA SCL RESET IF-AGC GND DIF-OUT1 GND DIF-OUT2 KEY-IN1 CN3002 1 P-ON-H2 AUDIO(L)-OUT 2 3 GND AUDIO(R)-OUT 4 PROTECT3 5 AMP(L)-OUT 6 7 GND AMP(R)-OUT 8 P-ON-H1 9 10 P-ON+3V 11 PROTECT1 GND 12 P-ON+5V 13 P-ON+5V 14 PROTECT2 15 P-ON+7V 16 GND 17 18 GND 19 P-ON+3.3V 20 P-ON+3.3V 21 AL+3.3V 22 AL+3.3V 23 GND 24 OE2 25 REMOTE BACKLIGHT-SW 26 27 LED1 BACKLIGHT-ADJ 28 VCOM-PWM 29 CN301 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 CN3003 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 GND KEY-IN2 DVD-LED P-ON-H3(NU) DVD-MAIN-PWR DVD-P-ON DVD-REMOTE DVD-SDATA DVD-DISC-IN GND DVD-CS GND DVD-SCLK GND DVD-DISC-OUT LED-CONT GND DVD-Pr GND DVD-Pb GND DVD-Y GND DVD-AUDIO(L) DVD-AUDIO-MUTE DVD-AUDIO(R) GND DVD-SPDIF GND CN303 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 1 2 3 4 5 6 7 8 9 10 11 12 13 CN902 DVD-Pr GND DVD-Pb GND DVD-Y GND GND GND DVD-AUDIO(L) DVD-AUDIO-MUTE DVD-AUDIO(R) GND DVD-SPDIF 13-1 TO DVD MAIN CBA UNIT CN601 TO DVD MAIN CBA UNIT CN401 1 CL802 2 1 CL801 2 CN901 AL+3.3V LED-CONT DVD-DISC-OUT EV+1.2V EV+1.2V EV+3.3V EV+3.3V EV+3.3V DVD-ON+3.3V DVD-ON+5V EV+9V EV+9V GND GND GND GND GND GND GND PWRCON(NU) DVD-SCLK DVD-CS DVD-DISC-IN DVD-SDATA DVD-REMOTE DVD-P-ON CN802 SP(R)SP(R)+ CN801 SP(L)SP(L)+ TO WIRING 2/2 DIAGRAM SP802 SPEAKER R-CH SP801 SPEAKER L-CH TU301 TUNER UNIT POWER SUPPLY CBA CN101 1 2 3 4 5 6 7 8 CL701A 1 2 3 4 5 6 7 8 9 CL101 GND REMOTE AL+3.3V LED1 P-ON-H1 KEY-IN1 KEY-IN2 DVD-LED CL701 S-VIDEO-Y-IN S-VIDEO-SW S-VIDEO-C-IN GND VIDEO-IN GND AUDIO(L)-IN GND AUDIO(R)-IN CN1001 15 GND 14 INV+16V 13 GND BACKLIGHT-ADJ 12 BACKLIGHT-SW 11 10 PROTECT3 9 GND 8 LCD+16V 7 LCD+16V 6 VGH 5 GND 4 P-ON+3.3V 3 LCD-8V 2 VCOM 1 GND CN201 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 CL103C 1 2 3 4 CBA IR SENSOR CBA CL101B CL701B 1 2 3 4 JACK 5 6 7 8 9 1 2 3 4 5 6 7 8 CN1003 1 2 3 4 5 6 7 8 9 10 11 CN1200 1 2 CN1150 1 2 CN1100 1 2 CN1050 1 2 INVERTER CBA ACL HOT-GND CN1900 1 2 CN602 1 2 DIGITAL MAIN CBA UNIT CL103 AL+3.3V GND KEY-IN1 KEY-IN2 S-VIDEO -IN AUDIO(R) -IN AUDIO(L) -IN VIDEO-IN GND LCD+16V LCD+16V VGH GND P-ON+3.3V P-ON+3.3V LCD-6.8V GND VCOM GND FUNCTION CBA CL103B 1 2 3 4 LCD MODULE ASSEMBLY BACK LIGHT BACK LIGHT BACK LIGHT BACK LIGHT CL3902 STV XAO OE1 CPV POL TP GND LLV5(-) LLV5(+) LLV4(-) LLV4(+) LLV3(-) LLV3(+) GND LLVCLK(-) LLVCLK(+) GND LLV2(-) LLN2(+) LLV1(-) LLV1(+) LLV0(-) LLV0(+) GND CN3005 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 HDMICONNECTOR-2 HDMICONNECTOR-1 USB JACK Wiring 1/2 Diagram WIRING DIAGRAM FL11.11WI1 PICKUP DETECTOR 7 9 11 2 3 6 5 4 TS DRIVE CBA LOAD-DISC 1 2 3 4 SENSOR CBA LED-POWER DVD-DISC-OUT DVD-DISC-IN GND DISC-IN 1 2 3 4 DISC-OUT CN5001 CN5001 is soldered directly to the PCB. CN801 AL+3.3V LED-CONT DVD-DISC-OUT EV+1.2V EV+1.2V EV+3.3V EV+3.3V EV+3.3V DVD-ON+3.3V DVD-ON+5V EV+9V EV+9V GND GND GND GND GND GND GND PWRCON(NU) DVD-SCLK DVD-CS DVD-DISC-IN DVD-SDATA DVD-REMOTE DVD-P-ON CN401 (CL901) TO POWER SUPPLY CBA CN901 TO WIRING 1/2 DIAGRAM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 FS 1 2 3 4 5 6 SLED MOTOR M SP(+) SP(-) GND SL(-) SL(+) LOAD-DISC SPINDLE MOTOR M CN201 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 CN301 DVD-Pr GND DVD-Pb GND DVD-Y GND GND GND DVD-AUDIO(L) DVD-AUDIO-MUTE DVD-AUDIO(R) GND DVD-SPDIF DVD-ON+5V CD/DVD D A C B NU VREF NU GND CD-LD GND(LD) DVD-LD PD-MONI GND(DVD-PD) GND(CD-PD) TS(-) FS(-) FS(+) TS(+) DVD MAIN CBA UNIT 4 5 6 7 8 9 10 11 12 13 14 15 16 CN601 (CL902) TO POWER SUPPLY CBA CN902 DVD MECHANISM Wiring 2/2 Diagram 13-2 FL11.11WI2 SYSTEM CONTROL TIMING CHARTS Disc In ~ Play/Play ~ Disc Out Disc In Disc IN (TL221) Disc Rotation Play Disc Stop Disc Out 3.3V 0V Sled Drive (TP303) 1.65V Disc Drive (TP301) 1.65V Focus Drive (TP304) 1.65V 0V 0V 0V Tracking Drive (TP302) 1.65V 0V 14-1 TVDVDN_TI LEAD IDENTIFICATIONS KTA1267-GR-AT/P E C B 2SA950-O(TE2 F T) 2SC2120-(O,Y)(TE2 F T) 2SD400(E) KTC3198-Y-AT/P KTC3200-GR-AT/P LTV-817MCF TL3472CDR 8 7 6 5 1 2 1: GND 2: Vout 3: Vin 1: 4 2: 3 3: 4: B C E NJM4558M(TE1) 8 5 1 4 A K E C 1 2 3 4 TC4052BF(ELNF) TL494CDR 9 16 2SC4881F GD S E C B LD1117V 1 2 3 2SK2417(FT) TK5A50D TK8A50D BD5426EFS-E2 KIA1117API00 23 44 1: ADJ 2: OUTPUT 8 1 1 22 3: INPUT 1 2 3 BA10324AF-E2 14 8 1 7 Note: A: Anode K: Cathode E: Emitter C: Collector B: Base R: Reference S: Source G: Gate D: Drain 15-1 FL11.11LE EXPLODED VIEWS Cabinet [LD320SS2, 32MD301B/F7] B15 A24 A1 L2 A6 B5 Inverter CBA L2 B15 B15 L2 CL801 B31 L2 A12 B4 CL201 L2 L1 A8 SP801 B9 B15 A42 L8 B19 B13 L2 B30 Function CBA A2 L16 L2 A5 CL101 L3 B13 CL103 CL802 L2 L2 L3 IR Sensor CBA L8 L16 B19 L1 L1 L8 SP802 B10 B19 L8 CL902 LCD1 CL3902 L16 A11 CL701 L1 L1 S5 L1 S5 B8 L7 L7 B14 CL1003 A10 A14 Jack CBA L3 B11 1B1 DVD Main CBA Unit Stand Assembly L8 L10 L8 L8 L8 CL901 Power Supply CBA CL4001 CL3702 CL3701 See Electrical Parts List for parts with this mark. AC601 B1 L9 B44 Digital Main CBA Unit L8 L6 L6 B27 A13 16-1 FL11.11-A_CEX Cabinet [32MD311B/F7] A1 B15 L2 A6 B5 A24 Inverter CBA CL801 L2 B15 B15 L2 B31 L2 A12 B4 CL201 L2 L1 A8 B9 B19 SP801 A3 B13 Function CBA L16 L3 B55 A4 CL101 L3 IR Sensor CBA L8 L16 B19 L1 L1 L8 CL802 B10 L8 CL902 B19 LCD1 CL3902 L16 A11 CL701 L1 L1 S5 L1 S5 L2 L7 L7 B14 CL1003 A10 A14 B13 L2 CL103 L2 B8 L2 B30 B15 A42 L8 Jack CBA L3 B11 1B1 DVD Main CBA Unit Stand Assembly L8 L10 L8 L8 L8 CL901 Power Supply CBA CL4001 CL3702 CL3701 AC601 B1 See Electrical Parts List for parts with this mark. L9 B44 Digital Main CBA Unit L8 L6 L6 B27 A13 16-2 FL11.11-A_CEX Packing S2 Some Ref. Numbers are not in sequence. Stand Assembly S9 S5 S6 Fixlon Tape X3 X10 L9 X6 X2 X4 S2 Packing Tape Tape S3 S4 X1 S3 Packing Tape S1 S5 FR ON FR ON T T S1 16-3 FL11.11PEX PARTS LIST [LD320SS2 (Serial No.: DS1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. Ref. No. L16 Description STAND ASSEMBLY A9DF1UH LCD MODULE CMO 6BIT A GRADE UJ32MXF SP801 SPEAKER MAGNETIC S0412F06A DSD0809XQ006 SP802 SPEAKER MAGNETIC S0412F06A DSD0809XQ006 CARTON A1DF2UH 1EM434688 S2 STYROFOAM TOP A94F0UH 1EM023410 S3 STYROFOAM BOTTOM A94F0UH 1EM023411 S4 SET BAG (900X850) A8AFFUH 1EM324904A S5 SERIAL NO. LABEL A01PBUH ---------- S6 STAND BAG A94F0UH 1EM428757 S9 STAND HOLD PAD A94F1UH 1EM023746 1EM126153 X1 BAG POLYETHYLENE 235X365XT0.03 0EM408420A OWNERS MANUAL A1DF2UH 1EMN27599 Part No. 1ESA25567 FRONT CABINET A94F1UH 1EM023485A A2 CONTROL PLATE A94F0UH 1EM325777 DECORATION PLATE A1DF2UH LCD1 S1 A1 A5 Part No. GBHS3100 PACKING NOTE: Parts that are not assigned part numbers (---------) are not available. Ref. No. Description SCREW TAP TIGHT M3X10 BIND HEAD+BLK NI ACCESSORIES A6 REAR CABINET A9DF0UH 1EM025345 X2# A8 AC CORD HOLDER A94F0UH 1EM325557 X3 REMOTE CONTROL NF033UD NF033UD A10# RATING LABEL A1DF2UH ---------- X4 DRY BATTERY(SUNRISE) R6SSE/2S XB0M451MS002 A11 JACK LABEL A9DF0UH 1EM431077 X6 QUICK START GUIDE A1DF2UH 1EMN27600 ---------- X10 REGISTRATION CARD (SYLVANIA) A017DUH 1EMN27080 A12 POP LABEL A1DF2UH A13 JACK HOLDER A94F0UH 1EM123173 A14 CAUTION LABEL A1DF2UH ---------- A24 ENERGY STAR LABEL ---------- A42 ENERGY GUIDE LABEL ---------- 1B1 DVD MECHA SLOT E7 N7XT3KVM N7XT3KVM B1 SHIELD BOX A17F4UH 1EM225624 B4 STAND HOLDER 32W A94F0UH 1EM222763 B5 WALL MOUNT BRACKET A84N0UH 1EM323797 B8 SPEAKER HOLDER (L) A94F0UH 1EM123233 B9 SPEAKER HOLDER (R) A94F0UH 1EM123234 B10 DVD HOLDER 32W A94F0UH 1EM023408 B15 CLOTH(10X180XT0.5) L0336JG 0EM408827 B19 CLOTH(15X110XT 0.5) L0110UA 0EM408385 B27 GASKET A8AF0UH 1EM425861 B30 LASER CAUTION LABEL A94F0UH ---------- B31 FELT A94F0UH 1EM428797 B44 THERMAL SHEET TMS-14-20 12X12 XK10000X4011 CL201 WIRE ASSEMBLY 15PIN FFC 15PIN 140MM WX1A94F0-104 CL801 WIRE ASSEMBLY 2PIN 2PIN 310MM RED BLACK WX1A94F0-202 CL802 WIRE ASSEMBLY 2PIN 2PIN 100MM RED BLACK WX1A94F0-203 CL901 WIRE ASSEMBLY 26PIN FFC 26PIN 260MM WX1A94F0-112 CL902 WIRE ASSEMBLY 13PIN FFC 13PIN 155MM WX1A94F0-103 CL1003 WIRE ASSEMBLY 11PIN FFC 11PIN 129MM WX1A91F6-101 CL3701 WIRE ASSEMBLY 29PIN FFC 29PIN 50MM WX1A94F0-101 CL3702 WIRE ASSEMBLY 29PIN FFC 29PIN 70MM WX1A94F0-111 CL3902 WIRE ASSEMBLY 24PIN FFC 24PIN 117.5MM WX1A91F6-102 CL4001 WIRE ASSEMBLY 29PIN FFC 29PIN 50MM WX1A94F0-101 L1 SCREW P-TIGHT M4X14 BIND HEAD+BLK GBHP4140 L2 SCREW P-TIGHT 3X10 BIND HEAD+ GBHP3100 L6 SCREW S-TIGHT M3X8 BIND HEAD+ GBHS3080 L7 DOUBLE SEMS SCREW M4X10 + BLK FPH34100 L8 ASSEMBLED SCREW ( D9 M3X6 ) A71F0UH 1EM424392B L9 STAND SCREW KIT A94F0UH 1ESA19508 L10 SCREW P-TIGHT 3X12 WASHER HEAD+ GCJP3120 20110111 17-1 A1DF2CA Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. Ref. No. NOTES: 1. Parts that are not assigned part numbers (---------) are not available. 2. Tolerance of Capacitors and Resistors are noted with the following symbols. C.....±0.25% D.....±0.5% F.....±1% G.....±2% J......±5% K.....±10% M.....±20% N.....±30% Z.....+80/-20% DIGITAL MAIN CBA UNIT Ref. No. Description DIGITAL MAIN CBA UNIT Part No. A1DF2MMA-001 DVD MAIN CBA UNIT Ref. No. Description DVD MAIN CBA UNIT MPW CBA Ref. No. Description Part No. MPW CBA Consists of the following: A1DF2MP1-001 POWER SUPPLY CBA JACK CBA ------------------- POWER SUPPLY CBA Ref. No. Description POWER SUPPLY CBA Consists of the following: Part No. ---------- CAPACITORS C201 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104 C202 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104 C203 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104 C204 ELECTROLYTIC CAP. 2.2µF/50V M CE1JMASDL2R2 C207 CHIP CERAMIC CAP.(1608) B K 0.1µF/16V CHD1CK30B104 C210 ELECTROLYTIC CAP. 22µF/50V M CE1JMASDL220 C216 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 C217 CHIP CERAMIC CAP.(1608) B K 0.1µF/16V CHD1CK30B104 C218 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105 C219 ELECTROLYTIC CAP. 47µF/25V M CE1EMASDL470 C221 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 C222 ELECTROLYTIC CAP. 470µF/25V M CE1EMASDL471 C223 ELECTROLYTIC CAP. 22µF/50V M CE1JMASDL220 C224 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 C302 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104 C303 ELECTROLYTIC CAP. 330µF/10V M CE1AMASDL331 C305 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104 C306 ELECTROLYTIC CAP. 1µF/50V M CE1JMASDL1R0 20110314 17-2 Part No. CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 C310 CHIP CERAMIC CAP.(1608) CH J 47pF/50V CHD1JJ3CH470 C311 CHIP CERAMIC CAP.(1608) CH J 47pF/50V CHD1JJ3CH470 C501 ELECTROLYTIC CAP. 100µF/25V M CE1EMASDL101 C601# CAP METALIZED FILM 0.47µF/300V K 3.5MM CT2F474DC004 C602# CAP METALIZED FILM 0.47µF/300V K 3.5MM CT2F474DC004 C605 CAP ELECTROLYTIC 470µF/200V M CA2D471DYG07 C609 POLYESTER FILM CAP. (PB FREE) 0.047µF/ 100V J CA2A473DT018 C611 CERAMIC CAP. 470pF/2KV CA3D471PAN04 C612 POLYESTER FILM CAP. (PB FREE) 0.068µF/ 100V J CA2A683DT018 C613 POLYESTER FILM CAP. (PB FREE) 0.0015µF/ 100V J CA2A152DT018 C631 ELECTROLYTIC CAP. 1000µF/25V M CE1EMZNDL102 C632 ELECTROLYTIC CAP. 220µF/25V M CE1EMASDL221 C633 CAP ALUMINUM ELECTOLYTIC 2200µF/6.3V M CE0KMZNDL222 C634 ELECTROLYTIC CAP. 1000µF/10V M CE1AMASDL102 C637 CERAMIC CAP. 2200pF/1KV CCD3AKA0R222 C638 ELECTROLYTIC CAP. 220µF/50V M CE1JMASDL221 C639 ELECTROLYTIC CAP. 1000µF/35V M CE1GMZADL102 C642 ELECTROLYTIC CAP. 0.47µF/50V M CE1JMASDLR47 C644 ELECTROLYTIC CAP 3300µF/16V M CE1CMZNDL332 C645 CAP ALUMINUM ELECTOLYTIC 2200µF/6.3V M CE0KMZNDL222 C646 POLYESTER FILM CAP. (PB FREE) 0.0022µF/ 100V J CA2A222DT018 C647 ELECTROLYTIC CAP. 1µF/50V M CE1JMASDL1R0 C648 ELECTROLYTIC CAP. 100µF/10V M CE1AMASDL101 C652 ELECTROLYTIC CAP. 1000µF/6.3V M CE0KMASDL102 C653 ELECTROLYTIC CAP. 220µF/10V M CE1AMASDL221 C654 ELECTROLYTIC CAP. 220µF/10V M CE1AMASDL221 C656 ELECTROLYTIC CAP. 100µF/16V M CE1CMASDL101 C657 ELECTROLYTIC CAP. 22µF/50V M CE1JMASDL220 C676 ELECTROLYTIC CAP. 2.2µF/50V M CE1JMASDL2R2 C681 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104 C682 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104 C683 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104 C684 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104 C691# SAFTY CAP. 1000pF/250V KX CA2E102MR101 C693# SAFTY CAP. 1000pF/250V KX CA2E102MR101 C723 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 Part No. N7ETFKUP Description C309 C724 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 C731 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390 C732 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390 C733 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390 C743 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 C744 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 C771 ELECTROLYTIC CAP. 100µF/16V M CE1CMASDL101 C772 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104 C775 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101 C776 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101 C801 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105 C802 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 C803 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105 C804 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 C805 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 CHD1EK30B105 C806 CHIP CERAMIC CAP.(1608) B K 1µF/25V C807 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 C808 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 C809 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 A1DF2EL Ref. No. C810 Description CHIP CERAMIC CAP.(1608) B K 0.1µF/25V Part No. C811 CHIP CERAMIC CAP.(1608) B K 0.47µF/16V CHD1CK30B474 C815 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105 C816 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 C817 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105 C818 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 C819 ELECTROLYTIC CAP. 10µF/50V M C820 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105 C821 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 C822 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 C823 ELECTROLYTIC CAP. 1000µF/25V M CE1EMZNDL102 C824 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105 C825 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 C826 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 C827 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 CE1JMASDL100 C828 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 C829 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 C830 CHIP CERAMIC CAP.(1608) B K 0.47µF/16V CHD1CK30B474 C832 ELECTROLYTIC CAP. 3.3µF/50V M CE1JMASDL3R3 C833 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 C834 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105 C835 CHIP CERAMIC CAP.(1608) B K 2700pF/50V CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105 C837 CHIP CERAMIC CAP.(1608) B K 2700pF/50V CHD1JK30B272 C838 CHIP CERAMIC CAP.(1608) CH J 470pF/50V CHD1JJ3CH471 C841 CHIP CERAMIC CAP.(1608) CH J 470pF/50V CHIP CERAMIC CAP. F Z 1µF/10V CHD1JJ3CH471 CHD1AZ30F105 C842 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105 C843 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 C844 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 C845 CHIP CERAMIC CAP.(1608) CH J 470pF/50V CHD1JJ3CH471 C846 CHIP CERAMIC CAP.(1608) CH J 470pF/50V CHD1JJ3CH471 C847 CHIP CERAMIC CAP.(1608) B K 0.1µF/25V CHD1EK30B104 C871 C872 CHIP CERAMIC CAP.(1608) B K 3300pF/50V CHIP CERAMIC CAP.(1608) B K 3300pF/50V CHD1JK30B332 CHD1JK30B332 C873 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 C874 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 C875 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101 C876 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101 C877 CHIP CERAMIC CAP.(1608) B K 6800pF/50V CHD1JK30B682 C878 CHIP CERAMIC CAP.(1608) B K 6800pF/50V CHD1JK30B682 C879 C880 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V ELECTROLYTIC CAP. 100µF/16V M CHD1EZ30F104 CE1CMASDL101 C882 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 C883 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 C884 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 C885 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 C906 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222 C907 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222 C916 ELECTROLYTIC CAP. 1000µF/6.3V M CE0KMASDL102 C917 ELECTROLYTIC CAP. 220µF/6.3V M CE0KMASDL221 C918 ELECTROLYTIC CAP. 100µF/10V M CE1AMASDL101 C919 ELECTROLYTIC CAP. 47µF/25V M CE1EMASDL470 C951 ELECTROLYTIC CAP. 100µF/16V M CE1CMASDL101 C952 CHIP CERAMIC CAP.(1608) F Z 0.1µF/25V CHD1EZ30F104 C953 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105 C954 CHIP CERAMIC CAP. F Z 1µF/10V CHD1AZ30F105 C957 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 C958 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 C959 CHIP CERAMIC CAP. CH J 220pF/50V CHD1JJ3CH221 C960 CHIP CERAMIC CAP. CH J 220pF/50V CHD1JJ3CH221 CONNECTORS 20110314 Description Part No. CN101 PH CONNECTOR TOP 8P B8B-PH-K-S (LF)(SN) J3PHC08JG029 CN201 FFC CONNECTOR 15P IMSA-9615S-15A-PP-A JC96J15ER007 CN301 FFC CONNECTOR IMSA-9615S-29A-PP-A JC96J29ER007 CN302 FFC CONNECTOR IMSA-9615S-29A-PP-A JC96J29ER007 CN303 FFC CONNECTOR IMSA-9615S-29A-PP-A JC96J29ER007 CN602 WIRE ASSEMBLY 2PIN 2PIN 145MM RED BLACK WX1A94F0-201 CN801 PH CONNECTOR TOP 2P B2B-PH-K-S (LF)(SN) J3PHC02JG029 CN802 PH CONNECTOR TOP 2P B2B-PH-K-S (LF)(SN) J3PHC02JG029 CN901 FFC CONNECTOR IMSA-9615S-26A-PP-A JC96J26ER007 CN902 FFC CONNECTOR IMSA-9615S-13A-PP-A JC96J13ER007 DIODES CHD1JK30B272 C836 C839 Ref. No. CHD1EK30B104 17-3 D202 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D203 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D204 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036 D205 DIODE ZENER 24BSC-T26 NDTC024BST26 D206 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D207 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D208 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D209 DIODE ZENER 39BSB-T26 NDTB039BST26 D210 DIODE ZENER 6V2BSB-T26 NDTB6R2BST26 D211 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D404 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D405 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D406 DIODE ZENER 15BSB-T26 NDTB015BST26 D407 DIODE ZENER 10BSB-T26 NDTB010BST26 D409 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D410 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D411 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D412 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D413 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D414 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D415 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D416 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D417 DIODE ZENER 3V9BSB-T26 NDTB3R9BST26 D418 DIODE ZENER 3V9BSB-T26 NDTB3R9BST26 D419 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D420 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D421 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D601# DIODE GENERAL PURPOSE 1N5406-BU NDLZ1N5406BU D602# DIODE GENERAL PURPOSE 1N5406-BU NDLZ1N5406BU D603# DIODE GENERAL PURPOSE 1N5406-BU NDLZ1N5406BU D604# DIODE GENERAL PURPOSE 1N5406-BU NDLZ1N5406BU D606# DIODE ZENER 27BSB-T26 NDTB027BST26 D607 DIODE ZENER 4V3BSB-T26 NDTB4R3BST26 D609# SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D611 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D612# DIODE ZENER 39BSB-T26 NDTB039BST26 D620 DIODE ZENER 1ZB220-YBB NDWZ01ZB220Y D631 DIODE FR154 NDLZ000FR154 D632 DIODE FR104-B NDLZ000FR104 D633 DIODE FAST RECOVERY FR151-B/P NDWZ0FR151BP D634 SCHOTTKY BARRIER DIODE SB240-B/P NDWZ000SB240 D635 DIODE ZENER 24BSB-T26 NDTB024BST26 D637 SCHOTTKY BARRIER DIODE SB160 NDWZ000SB160 D638 DIODE FR154 NDLZ000FR154 D639 DIODE ZENER 1ZB43BB NDWZ0001ZB43 D641 SCHOTTKY BARRIER DIODE SB390 NDWZ000SB390 D642 SCHOTTKY BARRIER DIODE SB390 NDWZ000SB390 D643 DIODE FR104-B NDLZ000FR104 D644 DIODE ZENER 10BSB-T26 NDTB010BST26 A1DF2EL Ref. No. Description Part No. Ref. No. Description Part No. D645 SHUNT REGULATOR KIA431B-AT/P NSZBA0TJY038 Q205 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D646 DIODE SCHOTTKY SB360BH NDWZ000SB360 Q207 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P D647 SCHOTTKY BARRIER DIODE SB240-B/P NDWZ000SB240 Q208 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D648 SCHOTTKY BARRIER DIODE SB140 NDWZ000SB140 Q209 TRANSISTOR 2SD400(E) QQUE002SD400 D649 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q210 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D650 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q211 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D652 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26 Q212 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D655 RECTIFIER DIODE 1N4005 NDQZ001N4005 Q401 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D657 DIODE ZENER 33BSB-T26 NDTB033BST26 Q402 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D658 DIODE ZENER 3V3BSB-T26 NDTB3R3BST26 Q501 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F D659 DIODE ZENER 6V8BSA-T26 NDTA6R8BST26 Q601# FET MOS TK5A50D(FUNAI QEWZTK5A50DQ D660 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q602# TRANSISTOR 2SC2120-O(TE2 F T) QQS02SC2120F D661 DIODE FR154 NDLZ000FR154 Q631 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D662 DIODE FR154 NDLZ000FR154 Q634 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D664 DIODE ZENER 4V7BSB-T26 NDTB4R7BST26 Q635 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D665 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 Q636 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F D666 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036 Q637 QQWZ2SC4881F D670 DIODE ZENER 10BSB-T26 NDTB010BST26 NPN TRANSISTOR POWER 2SC4881F HFE MAX320 D671 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 Q638 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P Q639 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P Q640 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F Q641 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F Q642 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P Q643 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F Q771 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P Q772 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P Q801 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P Q802 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P Q841 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P Q871 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P Q872 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P Q873 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P Q874 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P Q901 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F Q902 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P Q903 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F Q904 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P R171 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R172 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R175 RES CARBON FILM T 1/4W J 22k Ω RCX4223T1001 R201 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R202 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 R204 RES CARBON FILM T 1/4W J 560 Ω RCX4561T1001 R206 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 R207 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R208 RES CHIP 1608 1/10W J 1 Ω RRJ1R0RYL002 R210 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 R212 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 R213 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R216 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R217 RES CHIP 1608 1/10W J 1.5k Ω RRJ152RYL002 R218 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R219 RES CHIP 1608 1/10W J 15k Ω RRJ153RYL002 R220 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 R223 RES CARBON FILM T 1/4W J 3.3k Ω RCX4332T1001 R224 RES CARBON FILM T 1/4W J 27k Ω RCX4273T1001 R225 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R226 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R227 METAL OXIDE FILM RES. 1W J 2.7 Ω RN012R7ZU001 R228 RES CARBON FILM T 1/4W J 2.7k Ω RCX4272T1001 R229 RES CARBON FILM T 1/4W J 2.7k Ω RCX4272T1001 R231 RES CHIP 1608 1/10W J 1.5k Ω RRJ152RYL002 D675 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 D676 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 D801 DIODE ZENER 20BSB-T26 NDTB020BST26 D802 DIODE ZENER 20BSB-T26 NDTB020BST26 D803 DIODE ZENER 20BSB-T26 NDTB020BST26 D804 DIODE ZENER 20BSB-T26 NDTB020BST26 D806 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D901 RECTIFIER DIODE 1N4005 NDQZ001N4005 D902 RECTIFIER DIODE 1N4005 NDQZ001N4005 D903 RECTIFIER DIODE 1N4005 NDQZ001N4005 D904 D905 DIODE FR104-B NDLZ000FR104 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036 D906 DIODE ZENER 3V9BSB-T26 NDTB3R9BST26 D907 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D909 RECTIFIER DIODE 1N4005 NDQZ001N4005 ICS IC201 IC TL3472CDR NSZBA0TTY115 IC601# PHOTO COUPLER LTV817MCF NPECLTV817MF IC631 IC LD1117V NSZBA0SSS046 IC771 IC801 IC SWITCHING TC4052BF(ELNF) IC D-AMP BD5426EFS-E2 QSZBA0TTS162 QSZBA0TRM137 IC871 IC OP AMP NJM4558M(TE1)-#ZZZB QSZBA0TJR089 IC901 IC REGULATOR KIA1117API00/TO-220 NSCA0S0JY009 IC951 IC OP AMP NJM4558M(TE1)-#ZZZB RESISTORS QSZBA0TJR089 COILS L302 CHIP INDUCTOR LK1608R22K-T LLACKB3TUR22 L303 CHIP INDUCTOR LK1608R22K-T LLACKB3TUR22 L601# COIL LINE FILTER ST0807ET28-009 10MH LLEG0Z0Y2029 L602# COIL LINE FILTER ST0807ET28-009 10MH LLEG0Z0Y2029 L801 RADIAL LEAD INDUCTORS 33µF LLARKGQTU330 L802 RADIAL LEAD INDUCTORS 33µF LLARKGQTU330 L803 RADIAL LEAD INDUCTORS 33µF LLARKGQTU330 L804 RADIAL LEAD INDUCTORS 33µF LLARKGQTU330 L871 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 L901 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 L951 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 TRANSISTORS Q171 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P Q172 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P Q201 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P Q202 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P Q203 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P Q204 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P 20110314 17-4 A1DF2EL Ref. No. Description R232 RES CHIP 1608 1/10W F 11.0k Ω R233 R234 Part No. Ref. No. Description Part No. RTW1102HH008 R660 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 RES CHIP 1608 1/10W F 750 Ω RTW7500HH008 R661 RES. CARBON FILM J 1/2W J 390 Ω RCX2391T1003 RES CHIP 1608 1/10W F 2.20k Ω RTW2201HH008 R662 RES CARBON FILM T 1/4W J 15 Ω RCX4150T1001 R235 RES CARBON FILM T 1/4W J 330 Ω RCX4331T1001 R663 RES CARBON FILM T 1/4W J 1.8k Ω RCX4182T1001 R236 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 R664 RES CARBON FILM T 1/4W J 1.8k Ω RCX4182T1001 R237 RES CARBON FILM T 1/4W J 8.2k Ω RCX4822T1001 R665 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 R238 RES CARBON FILM T 1/4W J 1.5k Ω RCX4152T1001 R666 RES CARBON FILM T 1/4W J 1.0 Ω RCX41R0T1001 R240 RES CARBON FILM T 1/4W J 47k Ω RCX4473T1001 R667 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 R241 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R668 RES CHIP 1608 1/10W F 620 Ω RTW6200HH008 R242 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 R669 RES CHIP 1608 1/10W F 1.00k Ω RTW1001HH008 R243 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001 R670 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 R245 RES CARBON FILM T 1/4W J 8.2k Ω RCX4822T1001 R671 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 R247 METAL OXIDE FILM RES. 1W J 2.7 Ω RN012R7ZU001 R672 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 R248 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R673 RES CARBON FILM T 1/4W J 22k Ω RCX4223T1001 R302 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R674 RES CARBON FILM T 1/4W J 1.0k Ω RCX4102T1001 R303 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R675 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R306 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R676 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R307 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R677 RES CARBON FILM T 1/4W J 270 Ω RCX4271T1001 R308 RES CHIP 1608 1/10W J 82 Ω RRJ820RYL002 R678 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 R309 RES CHIP 1608 1/10W J 82 Ω RRJ820RYL002 R679 RES CHIP 1608 1/10W F 3.60k Ω RTW3601HH008 R310 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R680 RES CHIP 1608 1/10W F 10.0k Ω RTW1002HH008 R401 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R682 RES CARBON FILM T 1/4W J 2.7 Ω RCX42R7T1001 R402 RES CARBON FILM T 1/4W J 22k Ω RCX4223T1001 R683 RES CARBON FILM T 1/4W J 2.7 Ω RCX42R7T1001 R403 RES CHIP 1608 1/10W J 47k Ω RRJ473RYL002 R685 RES CARBON FILM T 1/4W J 22 Ω RCX4220T1001 R404 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R686 RES CARBON FILM T 1/4W J 1.0k Ω RCX4102T1001 R405 RES CARBON FILM T 1/4W J 47k Ω RCX4473T1001 R687 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 R407 RES CARBON FILM T 1/4W J 22k Ω RCX4223T1001 R688 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 R408 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R689 RES CARBON FILM T 1/4W J 1.2k Ω RCX4122T1001 R410 RES CHIP 1608 1/10W F 43.0k Ω RTW4302HH008 R691 RES CARBON FILM T 1/4W J 2.7 Ω RCX42R7T1001 R411 RES CHIP 1608 1/10W F 56.0k Ω RTW5602HH008 R692 RES CARBON FILM T 1/4W J 2.7 Ω RCX42R7T1001 R412 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R693 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 R501 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 R694 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 R601# RES. CARBON FILM J 1/2W J 560k Ω RCX2564T1003 R695 RES CARBON FILM T 1/4W J 33 Ω RCX4330T1001 R602# CEMENT RESISTOR 5W J 2.2 Ω H 10MM RW052R2PAK10 R696 METAL OXIDE FILM RES. 1W J 3.3 Ω RN013R3ZU001 R604 RES CARBON FILM T 1/4W J 390k Ω RCX4394T1001 R697 METAL OXIDE FILM RES. 1W J 3.3 Ω RN013R3ZU001 R605 RES CARBON FILM T 1/4W J 390k Ω RCX4394T1001 R699 RES CARBON FILM T 1/4W J 56 Ω RCX4560T1001 R606 RES CARBON FILM T 1/4W J 390k Ω RCX4394T1001 R723 RES CHIP 1608 1/10W J 15k Ω RRJ153RYL002 R610 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001 R724 RES CHIP 1608 1/10W J 15k Ω RRJ153RYL002 R611 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001 R725 RES CHIP 1608 1/10W J 39k Ω RRJ393RYL002 R613 RES CARBON FILM T 1/4W J 1.2k Ω RCX4122T1001 R726 RES CHIP 1608 1/10W J 39k Ω RRJ393RYL002 R614# METAL OXIDE FILM RES. 2W J 0.39 Ω RN02R39ZU001 R731 RES CHIP 1608 1/10W J 75 Ω RRJ750RYL002 R615 RES CARBON FILM T 1/4W J 3.9k Ω RCX4392T1001 R732 RES CHIP 1608 1/10W J 75 Ω RRJ750RYL002 R616 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001 R733 RES CHIP 1608 1/10W J 75 Ω RRJ750RYL002 R617# CEMENT RESISTOR 5W J 2.2 Ω H 10MM RW052R2PAK10 R734 RES CHIP 1608 1/10W J 10 Ω RRJ100RYL002 R618 RES CARBON FILM T 1/4W J 390k Ω RCX4394T1001 R735 RES CHIP 1608 1/10W J 10 Ω RRJ100RYL002 R636 RES. CARBON FILM J 1/2W J 2.7 Ω RCX22R7T1003 R736 RES CHIP 1608 1/10W J 10 Ω RRJ100RYL002 R637 RES CARBON FILM T 1/4W J 1.2k Ω RCX4122T1001 R743 RES CHIP 1608 1/10W J 15k Ω RRJ153RYL002 R638 RES CARBON FILM T 1/4W J 1.5k Ω RCX4152T1001 R744 RES CHIP 1608 1/10W J 15k Ω RRJ153RYL002 R639 RES CARBON FILM T 1/4W J 1.5k Ω RCX4152T1001 R745 RES CHIP 1608 1/10W J 39k Ω RRJ393RYL002 R641 RES CHIP 1608 1/10W D 1.10k Ω RTW1101HH007 R746 RES CHIP 1608 1/10W J 39k Ω RRJ393RYL002 R642 RES CHIP 1608 1/10W D 10.0k Ω RTW1002HH007 R763 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001 R643 RES CHIP 1608 1/10W D 10.0k Ω RTW1002HH007 R771 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 R644 RES CHIP 1608 1/10W F 820 Ω RTW8200HH008 R772 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R645 RES CARBON FILM T 1/4W J 270 Ω RCX4271T1001 R773 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R646 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001 R774 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R648 RES CHIP 1608 1/10W F 1.00k Ω RTW1001HH008 R775 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R650 RES CARBON FILM T 1/4W J 6.8k Ω RCX4682T1001 R776 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R651 RES CHIP 1608 1/10W J 1 Ω RRJ1R0RYL002 R777 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R652 RES CHIP 1608 1/10W F 24.0k Ω RTW2402HH008 R778 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R653 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 R779 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R654 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 R802 RES CHIP 1608 1/10W F 27.0k Ω RTW2702HH008 R658 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R803 RES CHIP 1608 1/10W F 11.0k Ω RTW1102HH008 R659 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R804 RES CHIP 1608 1/10W F 11.0k Ω RTW1102HH008 20110314 17-5 A1DF2EL Ref. No. Description Ref. No. Part No. Description Part No. R806 RES CHIP 1608 1/10W J 4.7k Ω RRJ472RYL002 R954 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R810 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R955 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R813 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R956 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R814 RES CHIP 1608 1/10W J 3.3k Ω RRJ332RYL002 R957 RES CHIP 1608 1/10W J 39k Ω RRJ393RYL002 R815 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R958 RES CHIP 1608 1/10W J 39k Ω RRJ393RYL002 R816 RES CHIP 1608 1/10W J 3.3k Ω RRJ332RYL002 R959 RES CHIP 1608 1/10W J 12k Ω RRJ123RYL002 R817 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R960 RES CHIP 1608 1/10W J 12k Ω RRJ123RYL002 R818 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R819 RES CARBON FILM T 1/4W J 22k Ω RCX4223T1001 R820 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R843 RES CHIP 1608 1/10W J 110 Ω MISCELLANEOUS AC601# AC CORD W/O A GND WIRE UL/CSA 1770 NO WAC0172LW022 BLACK RRJ111RYL002 B11 POW HEAT SINK A7120UH 1EM423993 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 R844 RES CHIP 1608 1/10W J 220 Ω RRJ221RYL002 BC301 R847 RES CHIP 1608 1/10W J 4.7k Ω RRJ472RYL002 BC601 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 R848 RES CHIP 1608 1/10W J 4.7k Ω RRJ472RYL002 BC801 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 RRJ561RYL002 BC802 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 R871 RES CHIP 1608 1/10W J 560 Ω R872 RES CHIP 1608 1/10W J 560 Ω RRJ561RYL002 BC803 R873 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 BC804 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 R874 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 BC805 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 RRJ102RYL002 BC841 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 WIRE ASSEMBLY 9P 9PIN/170MM WX1A94F0-002 R877 RES CHIP 1608 1/10W J 1k Ω R878 RES CARBON FILM T 1/4W J 1.0k Ω RCX4102T1001 CL701 R879 RES CHIP 1608 1/10W J 16k Ω RRJ163RYL002 F601# FUSE STC4A125V U/CT PAGE20CW3402 R880 RES CHIP 1608 1/10W J 16k Ω RRJ163RYL002 FH601 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002 RRJ101RYL002 FH602 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002 JACK RCA PCB S WHITE 01/RCA-101H(WH) JXRJ010YUQ02 R881 RES CHIP 1608 1/10W J 100 Ω R882 RES CHIP 1608 1/10W J 100 Ω RRJ101RYL002 JK721 R883 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 JK722 JACK RCA PCB S RED 01/RCA-101H(RD) JXRJ010YUQ01 R884 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 JK731 JACK RCA PCB S GREEN 01/RCA-101H(GN) JXRJ010YUQ03 RRJ104RYL002 JK732 JACK RCA PCB S BLUE 01/RCA-101H(BL) JXRJ010YUQ04 JACK RCA PCB S RED 01/RCA-101H(RD) JXRJ010YUQ01 R885 RES CHIP 1608 1/10W J 100k Ω R886 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 JK733 R887 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 JK741 JACK RCA PCB S WHITE 01/RCA-101H(WH) JXRJ010YUQ02 R888 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 JK742 JACK SW RCA PCB S RED RCA-102H(RD) JYRJ010YUQ03 R891 RES CHIP 1608 1/10W J 20k Ω RRJ203RYL002 JK841 JACK RCA PCB S ORANGE 01/RCA-101H(OR) JXRJ010YUQ06 R892 RES CHIP 1608 1/10W J 20k Ω RRJ203RYL002 JK871 JACK RCA PCB S WHITE 01/RCA-101H(WH) JXRJ010YUQ02 R893 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 JK872 JACK RCA PCB S RED 01/RCA-101H(RD) JXRJ010YUQ01 R901 RES CHIP 1608 1/10W J 91 Ω RRJ910RYL002 JS101 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 RRJ910RYL002 JS202 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 R902 RES CHIP 1608 1/10W J 91 Ω R903 RES CHIP 1608 1/10W J 91 Ω RRJ910RYL002 JS302 R904 RES CHIP 1608 1/10W J 1.3k Ω RRJ132RYL002 JS303 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 R905 RES CHIP 1608 1/10W J 1.3k Ω RRJ132RYL002 JS304 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 RRJ101RYL002 JS631 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 SCREW B-TIGHT D3X8 BIND HEAD+ GBJB3080 SURGE ABSORBER 470V+-10PER NVQZ10D471KB R906 RES CHIP 1608 1/10W J 100 Ω R909 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 L3 R910 RES CHIP.(1608) 1/10W J 0.30 Ω RRXAR30HH007 SA601# R911 RES CHIP.(1608) 1/10W J 0.30 Ω RRXAR30HH007 T601# TRANS POWER BCK-28-9932 LTT2PC0XB043 EYELET TYPE D-1 0VM406868 R912 RES CARBON FILM T 1/4W J 1.0k Ω RCX4102T1001 TM601 R913 RES. CARBON FILM J 1/2W J 3.3 Ω RCX23R3T1003 TM602 EYELET TYPE D-1 0VM406868 R914 RES. CARBON FILM J 1/2W J 2.7 Ω RCX22R7T1003 TU301 TUNER UNIT ATSC TDAU4-D05A UTNATS0AL002 R915 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001 R916 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R917 RES CARBON FILM T 1/4W J 390 Ω RCX4391T1001 R918 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R919 RES CARBON FILM T 1/4W J 150 Ω RCX4151T1001 R920 RES CARBON FILM T 1/4W G 3.3k Ω RCX4332T1002 R921 RES CARBON FILM T 1/4W G 10k Ω RCX4103T1002 C751 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101 R922 RES CARBON FILM T 1/4W J 22 Ω RCX4220T1001 C752 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101 R923 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001 C753 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101 R924 RES CARBON FILM T 1/4W J 3.9 Ω RCX43R9T1001 C754 RRZ000RYL002 R925 RES CARBON FILM T 1/4W J 3.9 Ω RES CHIP 1608 1/10W 0 Ω RCX43R9T1001 C755 RRZ000RYL002 R926 RES CARBON FILM T 1/4W J 470 Ω RES CHIP 1608 1/10W 0 Ω RCX4471T1001 C756 RRZ000RYL002 R927 RES CARBON FILM T 1/4W J 10 Ω RES CHIP 1608 1/10W 0 Ω RCX4100T1001 C757 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 R928 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001 C758 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225 JACK CBA Ref. No. Description JACK CBA Consists of the following: Part No. ---------- CAPACITORS R929 RES CARBON FILM T 1/4W J 1.2 Ω RCX41R2T1001 R951 RES CHIP 1608 1/10W J 100 Ω RRJ101RYL002 RES CHIP 1608 1/10W J 75 Ω RRJ750RYL002 R952 RES CHIP 1608 1/10W J 100 Ω R751 RRJ101RYL002 RES CHIP 1608 1/10W J 75 Ω RRJ750RYL002 R953 RES CHIP 1608 1/10W J 100k Ω R752 RRJ104RYL002 20110314 RESISTORS 17-6 A1DF2EL Ref. No. R753 Description RES CHIP 1608 1/10W J 75 Ω Ref. No. Part No. RRJ750RYL002 Description C1118 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V Part No. CHD1JK30B103 R756 RES CHIP 1608 1/10W J 100 Ω RRJ101RYL002 C1122 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 R757 RES CHIP 1608 1/10W J 100 Ω RRJ101RYL002 C1161 CAP CERAMIC HV 15pF/6.3KV/SL/J CCA1500MR001 R758 RES CHIP 1608 1/10W J 100 Ω RRJ101RYL002 C1162 CAP CERAMIC (AX) 1500pF/50V/B/K CA1J152TU061 R759 RES CHIP 1608 1/10W J 15k Ω RRJ153RYL002 C1163 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 R760 RES CHIP 1608 1/10W J 15k Ω RRJ153RYL002 C1164 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 R761 RES CHIP 1608 1/10W J 39k Ω RRJ393RYL002 C1165 CAP CERAMIC HV 15pF/6.3KV/SL/J CCA1500MR001 R762 RES CHIP 1608 1/10W J 39k Ω RRJ393RYL002 C1166 CAP CERAMIC (AX) 1500pF/50V/B/K CA1J152TU061 C1167 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 MISCELLANEOUS JK751 JACK SW DIN PCB L DIN-435C(777D) JYEL040YUQ03 C1168 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 JK752 JACK RCA PCB L RCA-101S(1)-03 JXRL010YUQ12 C1172 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 CCA1500MR001 JK753 JACK RCA PCB L RCA-101S(1)-04 JXRL010YUQ13 C1211 CAP CERAMIC HV 15pF/6.3KV/SL/J JK754 JACK SW RCA PCB L RCA-102F(RD) JYRL010YUQ05 C1212 CAP CERAMIC (AX) 1500pF/50V/B/K CA1J152TU061 C1213 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 C1214 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 C1215 CAP CERAMIC HV 15pF/6.3KV/SL/J CCA1500MR001 INVERTER ASSEMBLY Ref. No. Part No. C1216 CAP CERAMIC (AX) 1500pF/50V/B/K CA1J152TU061 INVERTER ASSEMBLY Consists of the following: Description A1DF2M1V-001 C1217 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 INVERTER CBA A1DF2M1V-001-IV ------------------------------------------------------------------ -------------------------------FUNCTION CBA A1DF2M1V-001-FNIR IR SENSOR CBA INVERTER CBA Ref. No. Description INVERTER CBA Consists of the following: Part No. ---------- CAPACITORS C1218 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 C1222 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1500 CERAMIC CAP. 470pF/2KV CA3D471PAN04 C1502 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 C1550 CERAMIC CAP. 470pF/2KV CA3D471PAN04 C1552 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 C1600 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1620 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102 C1702 CHIP CERAMIC CAP.(1608) F Z 0.22µF/50V CHD1JZ30F224 C1703 CHIP CERAMIC CAP.(1608) F Z 0.22µF/50V CHD1JZ30F224 C1800 ELECTROLYTIC CAP. 100µF/25V M CE1EMASDL101 C1001 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1801 ELECTROLYTIC CAP. 22µF/35V M CE1GMASDL220 C1002 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 C1802 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1003 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1905# SAFTY CAP. 2200pF/250V KX CA2E222MR101 C1004 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1910 CAP ELECTROLYTIC 270µF/200V CEA271DYG005 C1005 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1930 CERAMIC CAP. 820pF/2KV CA3D821PAN04 C1931# POLYESTER FILM CAP. (PB FREE) 0.001µF/ 100V J CA2A102DT018 C1932 POLYESTER FILM CAP. (PB FREE) 0.027µF/ 100V J CA2A273DT018 C1933 POLYESTER FILM CAP. (PB FREE) 0.1µF/100V CA2A104DT018 J C1970 POLYESTER FILM CAP. (PB FREE) 0.047µF/ 100V J C1006 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1007 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1008 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1009 ELECTROLYTIC CAP. 100µF/25V M CE1EMASDL101 C1011 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1012 POLYESTER FILM CAP. (PB FREE) 0.0039µF/ 100V J CA2A392DT018 C1013 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 C1981 CHIP CERAMIC CAP. F Z 0.01µF/50V CHD1JZ30F103 C1014 CHIP CERAMIC CAP.(1608) B K 6800pF/50V CHD1JK30B682 C1982 ELECTROLYTIC CAP. 0.47µF/50V M CE1JMASDLR47 CA2A473DT018 C1040 CHIP CERAMIC CAP.(1608) B K 0.47µF/10V CHD1AK30B474 C1990 CAP CERAMIC HV 820pF/1KV B K CA3A821TE006 C1052 ELECTROLYTIC CAP 100µF/100V CE2AMZNDL101 C1992# ELECTROLYTIC CAP 470µF/100V CE2AMZNDL471 C1053 ELECTROLYTIC CAP 100µF/100V CE2AMZNDL101 C1056 ELECTROLYTIC CAP 100µF/100V CE2AMZNDL101 CN1001 FFC CONNECTOR 15P IMSA-9615S-15A-PP-A JC96J15ER007 C1061 CAP CERAMIC HV 15pF/6.3KV/SL/J CCA1500MR001 CN1003 FFC CONNECTOR IMSA-9615S-11A-PP-A C1062 CAP CERAMIC (AX) 1500pF/50V/B/K CA1J152TU061 CN1050# CONNECTOR/JACK 1747386-1 JB17J02AP002 CONNECTORS JC96J11ER007 C1063 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 CN1100# CONNECTOR/JACK 1747386-1 JB17J02AP002 C1064 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 CN1150# CONNECTOR/JACK 1747386-1 JB17J02AP002 C1065 CAP CERAMIC HV 15pF/6.3KV/SL/J CCA1500MR001 CN1200# CONNECTOR/JACK 1747386-1 JB17J02AP002 C1066 CAP CERAMIC (AX) 1500pF/50V/B/K CA1J152TU061 CN1900# CONNECTOR B2P3-VH(LF)(SN) J3VH020JG001 C1067 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 C1068 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 D1000 DIODE ZENER 15BSB-T26 NDTB015BST26 C1072 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104 D1001 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 C1111 CAP CERAMIC HV 15pF/6.3KV/SL/J CCA1500MR001 D1003 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1112 CAP CERAMIC (AX) 1500pF/50V/B/K CA1J152TU061 D1004 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 DIODES C1113 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 D1005 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 C1114 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103 D1006 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1115 CAP CERAMIC HV 15pF/6.3KV/SL/J CCA1500MR001 D1040 DIODE ZENER 36BSB-T26 NDTB036BST26 C1116 CAP CERAMIC (AX) 1500pF/50V/B/K CA1J152TU061 D1060 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C1117 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100 D1061 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 20110314 17-7 A1DF2EL Ref. No. Description Ref. No. Part No. Description Part No. D1062 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1702 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1063 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1703 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1064 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1801 DIODE ZENER 10BSB-T26 NDTB010BST26 D1065 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1802 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 D1066 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1930# DIODE ZENER 27BSB-T26 NDTB027BST26 D1067 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1931 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26 D1068 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1932 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1069 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1933 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1070 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1934# DIODE ZENER 39BSB-T26 NDTB039BST26 D1071 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1970 DIODE ZENER 5V6BSB-T26 NDTB5R6BST26 D1072 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1971 DIODE ZENER HZS33NB2TE-EQ QDTBHZS33NB2 D1073 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1972 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1074 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1973 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1110 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1990 DIODE FAST RECOVERY 31DF4-FC QDWZ031DF4FC D1111 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1994 DIODE ZENER 1ZB100BB NDWZ001ZB100 D1112 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1113 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1114 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1115 SWITCHING DIODE 1SS133(T-77) ICS IC1000 IC PULSE-WIDTH-MODULATION CONT TL494CDR NSCA0T0TY006 QDTZ001SS133 IC1700 IC BA10324AF-E2 QSZBA0TRM032 PHOTO COUPLER LTV817MCF NPECLTV817MF PHOTO COUPLER LTV817MCF NPECLTV817MF D1116 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 IC1930# D1117 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 IC1931# D1118 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1119 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1001 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P TRANSISTORS D1120 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1003 D1121 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1004 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P D1122 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1005 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D1123 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1060 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D1124 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1061 D1160 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1110 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D1161 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1111 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D1162 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1160 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D1163 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1161 D1164 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1210 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D1165 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1211 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D1166 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1500 FET MOS 2SK2417(FT) QFWZSK2417FT TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F D1167 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1501 D1168 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1502 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F D1169 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1503 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D1170 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1550 FET MOS 2SK2417(FT) QFWZSK2417FT TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F D1171 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1551 D1172 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1552 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F D1173 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1553 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D1174 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1600 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P NQSYKTC3198P D1210 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1621 D1211 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1800 TRANSISTOR KTC3198-Y-AT/P D1212 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1801 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P D1213 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1802 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D1214 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1803 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D1215 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1804 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D1216 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1815 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F D1217 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1930# MOS FET TK8A50D QFWZTK8A50DQ TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P QQSY2SC2120F D1218 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1931# D1219 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1932# TRANSISTOR 2SC2120-Y(TE2 F T) D1220 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1970 NPN TRANSISTOR KTC3200-GR-AT/P NQSGKTC3200P D1221 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1971 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D1222 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 Q1972 TRANSISTOR KTC3198-Y-AT/P NQSYKTC3198P D1223 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D1224 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1001 RES CHIP 1608 1/10W F 22.0k Ω RTW2202HH008 D1500 DIODE ZENER 20BSB-T26 NDTB020BST26 R1002 RES CHIP 1608 1/10W F 1.00k Ω RTW1001HH008 D1550 DIODE ZENER 20BSB-T26 NDTB020BST26 R1003 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 D1630 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1004 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 D1700 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1005 RES CARBON FILM T 1/4W J 220k Ω RCX4224T1001 D1701 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 R1006 RES CARBON FILM T 1/4W J 56k Ω RCX4563T1001 20110314 RESISTORS 17-8 A1DF2EL Ref. No. Description Part No. Ref. No. R1007 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R1165 R1008 RES CHIP 1608 1/10W J 2.2k Ω RRJ222RYL002 R1009 RES CHIP 1608 1/10W J 82k Ω RRJ823RYL002 R1010 RES CHIP 1608 1/10W 0 Ω Description Part No. RES CARBON FILM T 1/4W J 27k Ω RCX4273T1001 R1166 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R1167 RES CHIP 1608 1/10W J 20k Ω RRJ203RYL002 RRZ000RYL002 R1168 RES CHIP 1608 1/10W J 390 Ω RRJ391RYL002 R1011 RES CHIP 1608 1/10W F 10.0k Ω RTW1002HH008 R1169 RES CHIP 1608 1/10W F 18.0k Ω RTW1802HH008 R1012 RES CHIP 1608 1/10W F 12.0k Ω RTW1202HH008 R1170 RES CHIP 1608 1/10W F 8.20k Ω RTW8201HH008 R1013 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R1171 RES CARBON FILM T 1/4W J 27k Ω RCX4273T1001 R1014 RES CHIP 1608 1/10W F 4.70k Ω RTW4701HH008 R1172 RES CHIP 1608 1/10W J 1M Ω RRJ105RYL002 R1015 RES CHIP 1608 1/10W F 7.50k Ω RTW7501HH008 R1210 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R1016 RES CHIP 1608 1/10W J 120k Ω RRJ124RYL002 R1211 RES CHIP 1608 1/10W J 20k Ω RRJ203RYL002 R1017 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R1212 RES CHIP 1608 1/10W J 390 Ω RRJ391RYL002 R1018 RES CARBON FILM T 1/4W J 2.2k Ω RCX4222T1001 R1213 RES CHIP 1608 1/10W F 18.0k Ω RTW1802HH008 R1019 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 R1214 RES CHIP 1608 1/10W F 8.20k Ω RTW8201HH008 R1021 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001 R1215 RES CARBON FILM T 1/4W J 27k Ω RCX4273T1001 R1022 RES CHIP 1608 1/10W F 2.20k Ω RTW2201HH008 R1216 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R1023 RES CHIP 1608 1/10W F 3.30k Ω RTW3301HH008 R1217 RES CHIP 1608 1/10W J 20k Ω RRJ203RYL002 R1024 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008 R1218 RES CHIP 1608 1/10W J 390 Ω RRJ391RYL002 R1026 RES CHIP 1608 1/10W F 220 Ω RTW2200HH008 R1219 RES CHIP 1608 1/10W F 18.0k Ω RTW1802HH008 R1028 RES CHIP 1608 1/10W F 36.0k Ω RTW3602HH008 R1220 RES CHIP 1608 1/10W F 8.20k Ω RTW8201HH008 R1030 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R1221 RES CARBON FILM T 1/4W J 27k Ω RCX4273T1001 R1031 RES CHIP 1608 1/10W J 15k Ω RRJ153RYL002 R1222 RES CHIP 1608 1/10W J 1M Ω RRJ105RYL002 R1032 RES CARBON FILM T 1/4W J 24k Ω RCX4243T1001 R1500 RES CHIP 1608 1/10W J 12k Ω RRJ123RYL002 R1033 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R1501 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 R1034 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R1502 RES CARBON FILM T 1/4W J 150 Ω RCX4151T1001 R1035 RES CARBON FILM T 1/4W J 3.3k Ω RCX4332T1001 R1503 RES CARBON FILM T 1/4W J 2.2k Ω RCX4222T1001 R1036 RES CARBON FILM T 1/4W J 10k Ω RCX4103T1001 R1504 RES CARBON FILM T 1/4W J 2.2k Ω RCX4222T1001 R1040 METAL OXIDE FILM RES. 2W J 0.39 Ω RN02R39ZU001 R1505 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 R1041 RES CARBON FILM T 1/4W J 33k Ω RCX4333T1001 R1506 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 R1043 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 R1550 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 R1044 METAL OXIDE FILM RES. 2W J 0.39 Ω RN02R39ZU001 R1551 RES CARBON FILM T 1/4W J 10 Ω RCX4100T1001 R1060 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R1552 RES CARBON FILM T 1/4W J 150 Ω RCX4151T1001 R1061 RES CHIP 1608 1/10W J 20k Ω RRJ203RYL002 R1553 RES CARBON FILM T 1/4W J 2.2k Ω RCX4222T1001 R1062 RES CHIP 1608 1/10W J 390 Ω RRJ391RYL002 R1554 RES CARBON FILM T 1/4W J 2.2k Ω RCX4222T1001 R1063 RES CHIP 1608 1/10W F 18.0k Ω RTW1802HH008 R1555 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 R1064 RES CHIP 1608 1/10W F 8.20k Ω RTW8201HH008 R1556 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 R1065 RES CARBON FILM T 1/4W J 27k Ω RCX4273T1001 R1600 RES CHIP 1608 1/10W J 18k Ω RRJ183RYL002 R1066 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R1601 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R1067 RES CHIP 1608 1/10W J 20k Ω RRJ203RYL002 R1620 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R1068 RES CHIP 1608 1/10W J 390 Ω RRJ391RYL002 R1621 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R1069 RES CHIP 1608 1/10W F 18.0k Ω RTW1802HH008 R1630 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R1070 RES CHIP 1608 1/10W F 8.20k Ω RTW8201HH008 R1631 RES CHIP 1608 1/10W J 3.3k Ω RRJ332RYL002 R1071 RES CARBON FILM T 1/4W J 27k Ω RCX4273T1001 R1700 RES CHIP 1608 1/10W F 9.10k Ω RTW9101HH008 R1072 RES CHIP 1608 1/10W J 1M Ω RRJ105RYL002 R1701 RES CHIP 1608 1/10W F 1.00k Ω RTW1001HH008 R1080 RES CHIP 1608 1/10W F 22.0k Ω RTW2202HH008 R1800 RES CHIP 1608 1/10W J 10k Ω RRJ103RYL002 R1081 RES CHIP 1608 1/10W J 5.6k Ω RRJ562RYL002 R1801 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R1110 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R1802 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R1111 RES CHIP 1608 1/10W J 20k Ω RRJ203RYL002 R1803 RES CARBON FILM T 1/4W J 4.7k Ω RCX4472T1001 R1112 RES CHIP 1608 1/10W J 390 Ω RRJ391RYL002 R1804 RES CARBON FILM T 1/4W J 1.2 Ω RCX41R2T1001 R1113 RES CHIP 1608 1/10W F 18.0k Ω RTW1802HH008 R1805 RES CARBON FILM T 1/4W J 1.0k Ω RCX4102T1001 R1114 RES CHIP 1608 1/10W F 8.20k Ω RTW8201HH008 R1806 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R1115 RES CARBON FILM T 1/4W J 27k Ω RCX4273T1001 R1807 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 R1116 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R1808 RES CHIP 1608 1/10W J 5.1k Ω RRJ512RYL002 R1117 RES CHIP 1608 1/10W J 20k Ω RRJ203RYL002 R1809 RES CHIP 1608 1/10W J 1.5k Ω RRJ152RYL002 R1118 RES CHIP 1608 1/10W J 390 Ω RRJ391RYL002 R1810 RES CARBON FILM T 1/4W J 4.7k Ω RCX4472T1001 R1119 RES CHIP 1608 1/10W F 18.0k Ω RTW1802HH008 R1811 RES CARBON FILM T 1/4W J 100k Ω RCX4104T1001 R1120 RES CHIP 1608 1/10W F 8.20k Ω RTW8201HH008 R1812 RES CARBON FILM T 1/4W J 12k Ω RCX4123T1001 R1121 RES CARBON FILM T 1/4W J 27k Ω RCX4273T1001 R1930 RES CARBON FILM T 1/4W J 47 Ω RCX4470T1001 R1122 RES CHIP 1608 1/10W J 1M Ω RRJ105RYL002 R1931 RES CARBON FILM T 1/4W J 47k Ω RCX4473T1001 R1160 RES CHIP 1608 1/10W J 100k Ω RRJ104RYL002 R1932 RES CARBON FILM T 1/4W J 82 Ω RCX4820T1001 R1161 RES CHIP 1608 1/10W J 20k Ω RRJ203RYL002 R1933 RES CARBON FILM T 1/4W J 82 Ω RCX4820T1001 R1162 RES CHIP 1608 1/10W J 390 Ω RRJ391RYL002 R1934 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001 R1163 RES CHIP 1608 1/10W F 18.0k Ω RTW1802HH008 R1935 RES CARBON FILM T 1/4W J 1.5k Ω RCX4152T1001 R1164 RES CHIP 1608 1/10W F 8.20k Ω RTW8201HH008 R1936 RES CARBON FILM T 1/4W J 180 Ω RCX4181T1001 20110314 17-9 A1DF2EL Ref. No. Description R1937# METAL OXIDE FILM RES. 2W J 0.33 Ω R1939 R1940 Part No. Ref. No. RN02R33ZU001 R151 RES CARBON FILM T 1/4W J 2.2k Ω RCX4222T1001 RES CARBON FILM T 1/4W J 220k Ω RCX4224T1001 R1941 RES CARBON FILM T 1/4W J 220k Ω RCX4224T1001 R1942 RES CARBON FILM T 1/4W J 120k Ω RCX4124T1001 Description Part No. WIRE COPPER 6111-06003-0120 XZ40C0SHG002 R152 RES CARBON FILM T 1/4W G 10k Ω RCX4103T1002 R153 RES CARBON FILM T 1/4W G 2.2k Ω RCX4222T1002 R154 RES CARBON FILM T 1/4W G 2.2k Ω RCX4222T1002 SWITCHES R1943 RES CARBON FILM 1/4W J 330k Ω RCX4334FS002 SW101A TACT SWITCH SKHHLMA010 SST0101AL049 R1944 RES CARBON FILM 1/4W J 330k Ω RCX4334FS002 SW103A TACT SWITCH SKHHLMA010 SST0101AL049 R1945 RES CARBON FILM 1/4W J 390k Ω RCX4394FS002 SW104A TACT SWITCH SKHHLMA010 SST0101AL049 R1967 RES CARBON FILM T 1/4W J 3.9k Ω RCX4392T1001 SW105A TACT SWITCH SKHHLMA010 SST0101AL049 R1968 RES CARBON FILM T 1/4W J 3.9k Ω RCX4392T1001 SW106A TACT SWITCH SKHHLMA010 SST0101AL049 R1969 RES CARBON FILM T 1/4W J 3.9k Ω RCX4392T1001 SW107A TACT SWITCH SKHHLMA010 SST0101AL049 R1970 RES CARBON FILM T 1/4W J 270 Ω RCX4271T1001 SW151 TACT SWITCH SKHHLMA010 SST0101AL049 R1971 RES CARBON FILM T 1/4W J 3.9k Ω RCX4392T1001 SW152 TACT SWITCH SKHHLMA010 SST0101AL049 R1972 RES CHIP 1608 1/10W J 68k Ω RRJ683RYL002 SW153 TACT SWITCH SKHHLMA010 SST0101AL049 R1973 RES CHIP 1608 1/10W J 22k Ω RRJ223RYL002 R1975 RES CHIP 1608 1/10W F 30.0k Ω RTW3002HH008 R1976 RES CHIP 1608 1/10W F 30.0k Ω RTW3002HH008 R1977 RES CHIP 1608 1/10W F 27.0k Ω RTW2702HH008 R1979 RES CHIP 1608 1/10W F 6.80k Ω RTW6801HH008 R1980 RES CHIP 1608 1/10W F 360 Ω RTW3600HH008 R1981 RES CHIP 1608 1/10W 0 Ω RRZ000RYL002 R1982 RES CHIP 1608 1/10W J 2.7k Ω RRJ272RYL002 R1983 RES CARBON FILM T 1/4W J 33k Ω RCX4333T1001 R1984 RES CARBON FILM T 1/4W J 15k Ω RCX4153T1001 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 RES CARBON FILM T 1/4W J 820k Ω RCX4824T1001 RES CARBON FILM T 1/4W J 1.0k Ω RCX4102T1001 R1986 R1987 R1988 IR SENSOR CBA Ref. No. Description IR SENSOR CBA Consists of the following: Part No. ---------- CAPACITORS C113 ELECTROLYTIC CAP. 47µF/16V M H7 CE1CMAVSL470 C115 CHIP CERAMIC CAP. CH J 330pF/50V CHD1JJ3CH331 D104 LED GREEN 333GT/E(FNA) NPWZ33GTEFNA D105 LED L-53HT NP4Z000L53HT D106 LED (YELLOW) LTL-307Y DIODES NPWZ0LTL307Y RESISTORS R1989 RES CARBON FILM 1/4W J 330k Ω RCX4334FS002 R1990 RES CARBON FILM 1/4W J 330k Ω RCX4334FS002 R123 RES CARBON FILM T 1/4W J 220 Ω R1991 RES CARBON FILM 1/4W J 330k Ω RCX4334FS002 R124 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001 R125 RES CHIP 1608 1/10W J 220 Ω RRJ221RYL002 R126 RES CHIP 1608 1/10W J 1k Ω RRJ102RYL002 R127 RES CARBON FILM T 1/4W J 3.3k Ω RCX4332T1001 R128 RES CARBON FILM T 1/4W J 100 Ω RCX4101T1001 MISCELLANEOUS B13 HEAT SINK PNA A94F0UH 1EM428121 B14 HEAT SINK PNB ASSEMBLY A94F0UH 1EM428123 BC1301 WIRE COPPER 6111-06003-0120 XZ40C0SHG002 RCX4221T1001 MISCELLANEOUS BC1500 COIL BEADS CORE FBR07VA850TB-00 LLBF00ZTU020 BC1501 COIL BEADS CORE FBR07VA850TB-00 LLBF00ZTU020 CL101 WIRE ASSEMBLY 8P 8PIN/170MM WX1A01F0-001 WIRE ASSEMBLY 4P 4PIN/250MM WX1A94F0-003 SENSOR REMOTE RECEIVER KSM-712TH2E USESJRSKK044 BC1550 COIL BEADS CORE FBR07VA850TB-00 LLBF00ZTU020 CL103 BC1551 COIL BEADS CORE FBR07VA850TB-00 LLBF00ZTU020 RS102 BC1930 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 BC1931 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030 L3 SCREW B-TIGHT D3X8 BIND HEAD+ GBJB3080 T1050# TRANS INVERTER HVT-153 LTZ3PZ0XB009 T1100# TRANS INVERTER HVT-153 LTZ3PZ0XB009 T1150# TRANS INVERTER HVT-153 LTZ3PZ0XB009 T1200# TRANS INVERTER HVT-153 LTZ3PZ0XB009 T1950# TRANS POWER BCK-35-0607 LTT3PC0XB048 FUNCTION CBA Ref. No. Description FUNCTION CBA Consists of the following: Part No. ---------- CAPACITORS C108 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062 C151 CAP CERAMIC (AX) 0.1µF/50V/F/Z CA1J104TU062 R108 RES CARBON FILM T 1/4W J 220 Ω RCX4221T1001 R109 RES CARBON FILM T 1/4W G 10k Ω RCX4103T1002 RESISTORS R111 RES CARBON FILM T 1/4W G 4.7k Ω RCX4472T1002 R112 RES CARBON FILM T 1/4W G 2.7k Ω RCX4272T1002 R113 RES CARBON FILM T 1/4W G 4.7k Ω RCX4472T1002 R114 RES CARBON FILM T 1/4W G 8.2k Ω RCX4822T1002 R115 RES CARBON FILM T 1/4W G 18k Ω RCX4183T1002 20110314 17-10 A1DF2EL PARTS LIST [32MD301B/F7 (Serial No.: DS1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model LD320SS2 (Serial No. : DS1) Ref. No. Description STAND ASSEMBLY A9DF0UH Part No. 1ESA26285 A1 FRONT CABINET A94F0UH 1EM023405 A5 DECORATION PLATE A1DF0UH 1EM126434 A10# RATING LABEL A1DF0UH ---------- L9 STAND SCREW KIT A1DA0UH 1ESA28845 S1 CARTON A1DF0UH 1EM435522 S9 STAND HOLD PAD A94F0UH 1EM023745 X2# OWNERS MANUAL A1DA0UH 1EMN28219 X3 REMOTE CONTROL NF801UD 192/ ECNLC7D1/NF801UD NF801UD X4 DRY BATTERY R03/2S XB0M451T0006 X6 QUICK START GUIDE A1DF0UH 1EMN28221 X10 REGISTRATION CARD (MAGNAVOX) A17N0UH 1EMN27759 2011/04/22 17-11 A1DF0CA.fm Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1. Parts that are not assigned part numbers (---------) are not available. 2. Tolerance of Capacitors and Resistors are noted with the following symbols. C.....±0.25% D.....±0.5% F.....±1% G.....±2% J......±5% K.....±10% M.....±20% N.....±30% Z.....+80/-20% Different parts from the original model LD320SS2 (Serial No. : DS1) Ref. No. Description Part No. DIGITAL MAIN CBA UNIT A1DF0MMA-001 DVD MAIN CBA UNIT N7EX1KUP 2011/04/22 17-12 A1DF0EL.fm 32MD311B/F7(A1DF4UH)(Serial No.: DS1) 20110407 32MD311B/F7(A1DF4UH)(Serial No.: DS1) Different parts from the original model LD320SS2(DS1) Ref. No. Description MECHANICAL PARTS STAND ASSEMBLY A9DF0UH A1 FRONT CABINET A1DF4UH A2 Not used A3 FUNCTION KNOB A1DF1UH A4 LED LENS A1DF1UH A5 Not used A10! RATING LABEL A1DF4UH A24 ENERGY STAR LABEL A91F2UH A42 ENERGY GUIDE LABEL A1DF4UH B30 LASER CAUTION LABEL A1DN2UH B55 SHIELD PLATE A1DF1UH L9 STAND SCREW KIT A1DA0UH S1 CARTON A1DF4UH S2 STYROFOAM TOP A1DF1UH S3 STYROFOAM BOTTOM A1DF1UH S4 SET BAG A17F6UH S9 STAND HOLD PAD A94F0UH X1 POLYETHYLENE BAG HDPE 180X340XT0.03 X2! OWNERS MANUAL A1DA0UH X3 REMOTE CONTROL NF801UD 192/ECNLC7D1/NF801UD X4 DRY BATTERY R03/2S X6 QUICK START GUIDE A1DF0UH X10 REGISTRATION CARD (MAGNAVOX) A17N0UH Parts No. 1ESA26285 1EM028285 1EM330937 1EM330657 ------------------------------------1EM330658 1ESA28845 1EM435925 1EM027806 1EM027808 1EM330877 1EM023745 1EM435579 1EMN28219A NF801UD XB0M451T0006 1EMN28221 1EMN27759 ELECTRICAL PARTS DIGITAL MAIN CBA UNIT A1DF0MMA-001 DVD MAIN CBA UNIT N7EX1KUP 1 / 1 page REVISION HISTORY Chassis FL11.11 • 2011-01-21 LD320SS2 (Serial No. : DS1) added • 2011-03-18 32MD301B/F7 (Serial No. : DS1) added • TBD 32MD311B/F7 (Serial No. : DS1) added 18-1 FL11.11REV COMPARISON LIST OF MODEL NAME Chassis FL11.11 LD320SS2 (DS1) A1DF2UH 32MD301B/F7 (DS1) A1DF0UH 32MD311B/F7 (DS1) A1DF4UH FL11.11COM