Download Allied Telesyn International Corp CentreCOM AT-200 Series User manual
Transcript
Allied Telesyn CentreCOM AT-810SL Multiport Transceiver Fanout User Manual Copyright 1994 Allied Telesyn International Corp. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn International Corp. Allied Telesyn International Corp. reserves the right to make changes in specifications and other information contained in this document without prior written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesyn International Corp. be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this manual or the information contained herein, even if Allied Telesyn International Corp. has been advised of, known, or should have known, the possibility of such damages. Trademarks: CentreCOM is a registered trademark of Allied Telesyn International Corp. Ethernet is a registered trademark of Xerox Corporation. UNIX is a registered trademark of UNIX System Laboratories. Novell and NetWare are registered trademarks of Novell, Inc. Microsoft and MS-DOS are registered trademarks and LAN Manager and Windows for Workgroups are trademarks of Microsoft Corporation. 3Com is a registered trademark of 3Com. PC-NFS is a trademark of Sun Microsystems, Inc. PC/TCP is a registered trademark of FTP Software, Inc. RADIATED ENERGY U.S. Federal Communications Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency and, if not installed and used in accordance with this instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Electrical Safety and Installation Requirements Note: Modifications or changes not expressly approved by the manufacturer or the FCC, can void your right to operate this equipment. Canadian Department of Communications This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications. Le présent appariel numérique n'émet pas de bruits radioélectriques dépassant les limites appicables aux appariels numériques de Classe A. Prescrites dans le réglement sur le brouillage radioélectrique édicté par le minestére des Communications Du Canada. This product has been tested and complies with the German Vfg 243/1991 requirements for Class B device. Warning Caution ! SAFETY ELECTRICAL NOTICES WARNING: ELECTRIC SHOCK HAZARD To prevent ELECTRIC shock, do not remove cover. No user-serviceable parts inside. This unit contains HAZARDOUS VOLTAGES and should only be opened by a trained and qualified technician. To avoid the possibility of ELECTRIC SHOCK, disconnect electric power to the product before connecting or disconnecting the LAN cables. LIGHTNING DANGER DANGER: DO NOT WORK on equipment or CABLES during periods of LIGHTNING ACTIVITY. CAUTION: POWER CORD IS USED AS A DISCONNECTION DEVICE. TO DE-ENERGISE EQUIPMENT, disconnect the power cord. INSTALLATION ELECTRICAL—AUTO VOLTAGE ADJUSTMENT This product will automatically adjust to any voltage between the ranges shown on the label. ELECTRICAL—TYPE CLASS 1 EQUIPMENT THIS EQUIPMENT MUST BE EARTHED. Power plug must be connected to a properly wired earth ground socket outlet. An improperly wired socket outlet could place hazardous voltages on accessible metal parts. ELECTRICAL—CORD NOTICE Use power cord, maximum 4.5 meters long, rated 6 amp minimum, 250V, made of HAR cordage molded IEC 320 connector on one end and on the other end a plug approved by the country of end use. Caution ! MOUNTING INSTRUCTIONS CAUTION: These models are designed for operation in the HORIZONTAL position. VERTICAL MOUNTING must not be done without the use of an Allied Telesyn vertical mount chassis designed for this purpose. CAUTION: Air vents must not be blocked and must have free access to the room ambient air for cooling. CAUTION: DO NOT detach rubber feet from the product unless an Allied Telesyn vertical mounting chassis is being used. OPERATING TEMPERATURE This product is designed for a maximum ambient temperature of 50 degrees Celsius. ALL COUNTRIES: Install product in accordance with local and National Electrical Codes. STRAHLUNGSENERGIE BESCHEINIGUNG DES HERSTELLERS/IMPORTEURS Hiermit wird bescheinigt, daß das Multiport Transceiver. Typenbezeichnung AT-810SL in Ubereinstimmung mit den Bestimmungen der BAPT-AmtsblVfg 243/1991 Klasse B funk-entstört ist. Der vorschriftsmäßige Betrieb mancher Geräte ( z. B MeBsender) kann allerdings gewissen Einschränkungen unterliegen. Beachten Sie deshalb die Hinweise in der Bedienungsanleitung. Dem Zentralamt fur Zulassungen im Fermeldewesen wurde das Inverkehrbringen dieses Gerätes angezeigt und die Berechtigung zur Überprufung der Serie auf Eienhaltung der Bestimmungen eingeräumt. Von Benutzer zusammengestellte Systeme, die dieses Gerat beihhhalten, müssen den Betimmungen von Vfg 243/1991 Klasse B, entsprechen. Achtung SICHERHEIT ACHTUNG: GEFÄHRLICHE SPANNUNG Das Gehäuse nicht öffnen. Das Gerät enthält keine vom Benutzer wartbaren Teile. Das Gerät steht unter Hochspannung und darf nur von qualifiziertem technischem Personal geöffnet werden. Vor Anschluß der LAN-Kabel, Gerät vom Netz trennen. GEFAHR DURCH BLITZSCHLAG GEFAHR: Keine Arbeiten am Gerät oder an den Kabeln während eines Gewitters ausführen Vorsicht ! VORSICHT: DAS NETZKABEL DIENT ZUM TRENNEN DER STROMVERSORGUNG. ZUR TRENNUNG VOM NETZ, KABEL AUS DER VORSICHT STECKDOSE ZIEHEN. iii INSTALLATION AUTOMATISCHE SPANNUNGSEINSTELLUNG Dieses Gerät stellt sich automatisch auf die auf dem Etikett aufgeführten Spannungswerte ein. KLASSE 1 GERÄTE DIESE GERÄTE MÜSSEN GEERDET SEIN. Der Netzstecker darf nur mit einer vorschriftsmäßig geerdeten Steckdose verbunden werden. Ein unvorschriftsmäßiger Anschluß kann das Metallgehäuse Teile unter gefährliche elektrische Spannungen setzen. NETZKABEL Das Netzkabel sollte eine maximale Länge von 4,5 Metern, einen Nennwert von mindestens 6 A und 250 V haben, aus HAR-Material hergestellt und mit einer gepreßten, IEC 320 entsprechenden, Anschlußverbindung an einem Ende, und am anderen Ende mit einem im Land des Endverbrauchers geprüften Stecker ausgestattet sein. Vorsicht ! MONTAGEANWEISUNGEN VORSICHT: Diese Modelle sind für Betrieb in horizontaler Position entworfen worden. Das Gerät darf NICHT OHNE Gebrauch eines dafür entworfenen Allied Telesyn-Vertikalmontagegestells in VERTIKALER Position montiert werden. VORSICHT: Die Entlüftungsöffnungen dürfen nicht versperrt sein und müssen zum Kühlen freien Zugang zur Raumluft haben. VORSICHT: Die Gummifüße NICHT ENTFERNEN, außer bei Gebrauch des Allied Telesyn-Vertikalmontagegestells. MONTAGEANWEISUNGEN VORSICHT: Diese Modelle sind für Betrieb in horizontaler Position entworfen worden. Das Gerät darf NICHT OHNE Gebrauch eines dafür entworfenen Allied Telesyn-Vertikalmontagegestells in VERTIKALER BETRIEBSTEMPERATUR Dieses Produkt wurde für den Betrieb in einer Umgebungstemperatur von nicht mehr als 50˚ C entworfen. ALLE LÄNDER: Installation muß örtlichen und nationalen elektrischen Vorschriften entsprechen. STRÅLINGSENERGI Dette kommercielle produkt opfylder de krav, der i USA stilles til udstyr af Klasse A. Dette produkt opfylder krav, der ifølge German Vfg 243/1991 stilles til udstyr af Klasse B. Advarsel SIKKERHED ELEKTRISKE FORHOLDSREGLER ADVARSEL: RISIKO FOR ELEKTRISK STØD For at forebygge ELEKTRISK stød, undlad at åbne apparatet. Der er ingen indre dele, der kan repareres af brugeren. Denne enhed indeholder LIVSFARLIGE STRØMSPÆNDINGER og bør kun åbnes af en uddannet og kvalificeret tekniker. For at undgå risiko for ELEKTRISK STØD, afbrydes den elektriske strøm til produktet, før LAN-kablerne monteres eller afmonteres. Advarsel FARE UNDER UVEJR FARE: UNDLAD at arbejde på udstyr eller KABLER i perioder med LYNAKTIVITET. ! ADVARSEL: DEN STRØMFØRENDE LEDNING BRUGES TIL AT AFBRYDE STRØMMEN. SKAL STRØMMEN TIL APPARATET AFBRYDES, tages ledningen ud af stikket. INSTALLATION ELEKTRISK—AUTOMATISK SPÆNDINGSREGULERING Dette apparat vil automatisk tilpasse sig enhver spænding indenfor de værdier, der er angivet på etiketten. ELEKTRISK—KLASSE 1-UDSTYR DETTE UDSTYR KRÆVER JORDFORBINDELSE. Stikket skal være forbundet med en korrekt installeret jordforbunden stikkontakt. En ukorrekt installeret stikkontakt kan sætte livsfarlig spænding til tilgængelige metaldele. ELEKTRISK—LEDNING Anvend ledning af maksimum 4,5 meters længde, med en kapacitet på minimum 6 amp., 250 v, bestående af en IEC 320 connector med indstøbt HAR ledning i den ene ende og et stik i den anden ende godkendt der er af myndighederne i brugerlandet. Advarsel ! INSTRUKTIONER FOR OPSTILLING ADVARSEL: Disse modeller er konstrueret til at betjenes i HORISONTAL position (vandret). VERTIKAL OPSTILLING (lodret) må IKKE FORETAGES uden brug af et Allied Telesyn vertikalt monteringsstel konstrueret til dette formål. ADVARSEL: Ventilationsåbninger må ikke blokeres og skal have fri adgang til den omgivende luft i rummet for afkøling. ADVARSEL: UNDLAD at fjerne gummisoklerne fra apparatet, med mindre der anvendes et Allied Telesyn vertikalt monteringsstel. BETJENINGSTEMPERATUR Dette apparat er konstrueret til en omgivende temperatur på maksimum 50 grader C. ALLE LANDE: Installation af produktet skal ske i overensstemmelse med lokal og national lovgivning for elektriske installationer. iv STRALINGSENERGIE Dit handelsprodukt werd getest en voldoet aan de Amerikaanse vereisten voor een klasse A toestel. Dit produkt werd getest en voldoet aan de Duitse Vfg 243/1991 vereisten voor een klasse B toestel. Waarschuwingen VEILIGHEID WAARSCHUWINGEN MET BETREKKING TOT ELEKTRICITEIT WAARSCHUWING: GEVAAR VOOR ELEKTRISCHE SCHOKKEN Gelieve het deksel niet te verwijderen, teneinde ELEKTRISCHE schokken te voorkomen. Binnenin bevinden zich geen onderdelen die door de gebruiker kunnen worden onderhouden. Dit toestel staat onder GEVAARLIJKE SPANNING en mag alleen worden geopend door een daartoe opgeleide en bevoegde technicus. Om het gevaar op ELEKTRISCHE SCHOKKEN te vermijden, moet u het toestel van de stroombron ontkoppelen alvorens de LAN-kabels te koppelen of ontkoppelen. GEVAAR VOOR BLIKSEMINSLAG Waarschuwingen GEVAAR: NIET aan toestellen of KABELS WERKEN bij BLIKSEM. ! WAARSCHUWING: HET TOESTEL WORDT UITGESCHAKELD DOOR DE STROOMKABEL TE ONTKOPPELEN. OM HET TOESTEL STROOMLOOS TE MAKEN: de stroomkabel ontkoppelen. INSTALLATIE ELEKTRISCH—AUTOMATISCHE AANPASSING VAN DE SPANNING Dit toestel past zich automatisch aan elke spanning aan, tussen de waarden op het label vermeld. ELEKTRISCHE—TOESTELLEN VAN KLASSE 1 DIT TOESTEL MOET GEAARD WORDEN. De stekker moet aangesloten zijn op een juist geaarde contactdoos. Een onjuist geaarde contactdoos kan de metalen onderdelen waarmee de gebruiker eventueel in aanraking komt onder gevaarlijke spanning stellen. ELEKTRISCHE—SNOEREN Gebruik een elektrisch snoer, maximum 4,5 meter lang, berekend voor ten minste 6 ampère, 250 V, uit HAR vervaardigd, met aan het ene uiteinde een gevormde IEC 320 stekker en aan het andere uiteinde een stekker die goedgekeurd is door het land waar het toestel zal worden gebruikt. Waarschuwing ! MONTAGE-INSTRUCTIES WAARSCHUWING: Deze modellen zijn ontworpen om te werken in HORIZONTALE stand. VERTICALE MONTAGE mag NIET UITGEVOERD WORDEN, tenzij een daartoe speciaal ontworpen Allied Telesyn chassis voor verticale montage wordt gebruikt. WAARSCHUWING: De ventilatiegaten mogen niet worden gesperd en moeten de omgevingslucht ongehinderd toelaten voor afkoeling. WAARSCHUWING: De rubberen voetjes NIET van het produkt LOSMAKEN behalve wanneer een chassis voor vertikale montage van Allied Telesyn wordt gebruikt. BEDRIJFSTEMPERATUUR De omgevingstemperatuur voor dit produkt mag niet meer bedragen dan 50 graden Celsius. ALLE LANDEN: het toestel installeren overeenkomstig de lokale en nationale elektrische voorschriften. ENERGIE RAYONNEE Ce matériel a été testé et est certifié conforme par la réglementation américaine aux normes définies pour les appareils de classe A. Ce matériel a été testé et est certifié conforme par la réglementation allemande Vfg 243/1991 aux normes définies pour les appareils de classe B. Avertissement Danger ! SECURITE INFORMATION SUR L’ELECTRICITE AVERTISSEMENT: DANGER D’ELECTROCUTION Pour empêcher les dangers d’ELECTROCUTION, ne pas enlever le couvercle. L’équipement ne contient aucun élément réparable par l’utilisateur. Cet appareil comprend des TENSIONS DANGEREUSES et ne doit être ouvert que par un technicien dûment qualifié. Pour éviter tout risque d’ELECTROCUTION, débrancher l’appareil de la prise de courant avant de connecter ou de déconnecter les câbles LAN. DANGER DE FOUDRE DANGER: NE PAS MANIER l’équipement ou les CABLES pendant les périodes d’activité orageuse. ATTENTION: LE CORDON D’ALIMENTATION SERT DE MISE HORS CIRCUIT POUR COUPER L’ALIMENTATION DE L’APPAREIL, débranchez le cordon. INSTALLATION ELECTRICITE—REGLAGE DE TENSION AUTOMATIQUE Ce produit peut s’ajuster automatiquement sur n’importe quelle tension comprise dans la plage indiquée sur le label. ELECTRICITE—EQUIPEMENT DE CLASSE 1 CET APPAREIL DOIT ETRE MIS A LA TERRE. La prise de courant doit être branchée dans une prise femelle correctement mise à la terre. Sinon, des tensions dangereuses risqueraient d’atteindre les pièces métalliques accessibles à l’utilisateur. ELECTRICITE—INFORMATION SUR LE CORDON Utiliser un cordon secteur de 4,5 mètres de long maximum, calibré à 6 ampères minimum, 250V, et fabriqué en câblage HAR avec connecteur IEC 32C moulé à une extrémité et à l’autre extrémité, une prise de courant mâle répondant aux normes du pays d’utilisation. Attention ! INSTRUCTIONS DE MONTAGE ATTENTION: Ces modèles sont destiné à fonctionner en position horizontale. L’appareil NE DOIT PAS être utilisé en MONTAGE VERTICAL sans employer un châssis de montage vertical Allied Telesyn conçu à cet effet. ATTENTION: Ne pas bloquer les fentes d’aération, ce qui empêcherait l’air ambiant de circuler librement pour le refroidissement. v ATTENTION: NE PAS ôter les pattes d’attache en caoutchouc du produit, à moins d’utiliser un châssis de montage vertical Allied Telesyn. TEMPERATURE DE FONCTIONNEMENT Ce produit est capable de tolérer une température ambiante maximum de 50 degrés Celsius POUR TOUS PAYS: Installer le produit conformément aux normes électriques nationales et locales. SÄTEILYENERGIA Tämä kaupallinen tuote on testattu ja noudattaa Yhdysvaltojen vaatimuksia luokan A laitteelle. Tämä kaupallinen tuote on testattu ja noudattaa Saksan Vfg 243/1991 -vaatimuksia luokan B laitteelle. Varoitus Hengenvaara ! TURVALLISUUS SÄHKÖÖN LIITTYVIÄ HUOMAUTUKSIA VAROITUS: SÄHKÖISKUVAARA Estääksesi SÄHKÖISKUN älä poista kantta. Sisällä ei ole käyttäjän huollettavissa olevia osia. Tämä laite sisältää VAARALLISIA JÄNNITTEITÄ ja sen voi avata vain koulutettu ja pätevä teknikko. Välttääksesi SÄHKÖISKUN mahdollisuuden katkaise sähkövirta tuotteeseen ennen kuin liität tai irrotat paikallisverkon (LAN) kaapelit. SALAMANISKUVAARA HENGENVAARA: ÄLÄ TYÖSKENTELE laitteiden tai KAAPELEIDEN KANSSA SALAMOINNIN AIKANA. HUOMAUTUS: VIRTAJOHTOA KÄYTETÄÄN VIRRANKATKAISULAITTEENA. VIRTA KATKAISTAAN irrottamalla virtajohto. ASENNUS SÄHKÖ —AUTOMAATTINEN JÄNNITTEENSÄÄTÖ Tämä tuote säätää automaattisesti mihin tahansa jännitteeseen ohjetarrassa annettujen arvojen välillä. SÄHKÖ —TYYPPILUOKAN 1 LAITTEET TÄMÄ LAITE TÄYTYY MAADOITTAA. Pistoke täytyy liittää kunnollisesti maadoitettuun pistorasiaan. Virheellisesti johdotettu pistorasia voi altistaa metalliosat vaarallisille jännitteille. SÄHKÖ —JOHTOON LIITTYVÄ HUOMAUTUS Käytä seuraavanlaista virtajohtoa: maksimipituus 4,5 metriä, minimiteho 6 ampeeria, 250 V, valmistettu HAR-johdostosta, muovattu IEC 320 -liitin toisessa päässä ja käyttömaassa hyväksytty pistoke toisessa päässä. Huomautus ! ASENNUSSOHJEET HUOMAUTUS: Nämä mallit on suunniteltu käytettäviksi VAAKA-asennossa. PYSTYASENNUSTA EI SAA TEHDÄ ilman Allied Telesyn -pystykiinnitysalustaa, joka on suunniteltu tähän tarkoitukseen. HUOMAUTUS: Ilmavaihtoreikiä ei pidä tukkia ja niillä täytyy olla vapaa yhteys ympäröivään huoneilmaan, jotta ilmanvaihto tapahtuisi. HUOMAUTUS: ÄLÄ irroita kumijalkoja tuotteesta, ellei Allied Telesyn-pystykiinnitysalusta ole käytössä. KÄYTTÖLÄMPÖTILA Tämä tuote on suunniteltu ympäröivän ilman maksimilämpötilalle 50° C. KAIKKI MAAT: Asenna tuote paikallisten ja kansallisten sähköturvallisuusmääräysten mukaisesti. ENERGIA IRRADIATA Questo prodotto commerciale è stato collaudato e risponde ai requisiti U.S.A. per i dispositivi di classe A. Questo prodotto è stato collaudato e risponde ai requisiti della legge tedesca Vfg 243/1991 per i dispositivi di classe B. Attenzione NORME DI SICUREZZA AVVERTENZE ELETTRICHE ATTENZIONE: PERICOLO DI SCOSSE ELETTRICHE Per evitare SCOSSE ELETTRICHE non asportare il coperchio. Le componenti interne non sono riparabili dall’utente. Questa unità ha TENSIONI PERICOLOSE e va aperta solamente da un tecnico specializzato e qualificato. Per evitare ogni possibilità di SCOSSE ELETTRICHE, interrompere l’alimentazione del dispositivo prima di collegare o staccare i cavi LAN. Pericolo PERICOLO DI FULMINI PERICOLO: NON LAVORARE sul dispositivo o sui CAVI durante PRECIPITAZIONI TEMPORALESCHE. ! ATTENZIONE: IL CAVO DI ALIMENTAZIONE È USATO COME DISPOSITIVO DI DISATTIVAZIONE. PER TOGLIERE LA CORRENTE AL DISPOSITIVO staccare il cavo di alimentazione. INSTALLAZIONE ELETTRICITÀ—REGOLAZIONE AUTOMATICA DELLA TENSIONE Questo prodotto regolerà automaticamente la tensione ad un valore compreso nella gamma indicata sull’etichetta. ELETTRICITÀ—DISPOSITIVI DI CLASSE 1 QUESTO DISPOSITIVO DEVE AVERE LA MESSA A TERRA. La spina deve essere inserita in una presa di corrente specificamente dotata di messa a terra. Una presa non cablata in maniera corretta rischia di scaricare una tensione pericolosa su parti metalliche accessibili. ELETTRICITÀ—AVVERTENZA SUL CAVO Usare un cavo della lunghezza massima di metri 4,5, con capacità minima di 6 A, 250 V, di filo HAR, dotato di connettore stampato IEC 320 ad un’estremità e di spina approvata dal paese di destinazione all’altra. Attenzione ! vi ISTRUZIONI PER IL MONTAGGIO ATTENZIONE: questi modelli sono concepiti per il funzionamento in posizione ORIZZONTALE. NON È POSSIBILE EFFETTUARE IL MONTAGGIO VERTICALE senza utilizzare l’apposito telaio per il montaggio verticale Allied Telesyn. ATTENZIONE: Le prese d’aria non vanno ostruite e devono consentire il libero ricircolo dell’aria ambiente per il raffreddamento. ATTENZIONE: NON staccare il piedino in gomma dal prodotto tranne qualora si utilizzi il telaio Allied Telesyn per il montaggio verticale. TEMPERATURA DI FUNZIONAMENTO Questo prodotto è concepito per una temperatura ambientale massima di 50 gradi centigradi. TUTTI I PAESI: installare il prodotto in conformità alle vigenti normative elettriche nazionali. UTSTRÅLT ENERGI Dette kommersielle produktet har blitt testet og er i samsvar med amerikanske krav for et A-Klasse apparat. Dette produktet har blitt testet og er i samsvar med tyske Vfg 243/1991 krav for et B-Klasse apparat. Advarsel Fare ! SIKKERHET ELEKTRISKE MEDDELELSE ADVARSEL: FARE FOR ELEKTRISK SJOKK For å unngå ELEKTRISK sjokk, må dekslet ikke tas av. Det finnes ingen deler som du kan bruke på innsiden. Denne enheten inneholder FARLIGE SPENNING, og må kun åpnes av en opplært, kvalifisert tekniker. For å unngå muligheten av ELEKTRISK SJOKK, må den elektriske strømmen til produktet være av når du slår LAN-ledninger av og på. FARE FOR LYNANTENNELSE FARE: MÅ IKKE BRUKES på utstyr eller ledninger mens LYN-AKTIVITET er i gang. FORSIKTIG: STRØMLEDNINGEN BRUKES TIL Å SLÅ APPARATET AV. HVIS DU VIL DEAKTIVISERE UTSTYRET, må du fjerne strømledningen. INSTALLASJON ELEKTRISK—AUTO SPENNINGSTILPASSING Dette produktet vil automatisk bli tilpasset hvilken som helst strøminnstilling i de områdene som vises på etiketten. ELEKTRISKE—TYPE 1. KLASSE UTSTYR DETTE UTSTYRET MÅ JORDES. Strømkontakten må være tilkoplet en korrekt jordet grunnstøpselkontakt. En støpselkontakt som ikke er jordet på rett måte, kan tilføre farlig spenning til lett tilgjengelige metalldeler. ELEKTRISKE—MEDDELELSE OM LEDNINGER Bruk en strømledning av maksimal størrelse 4,5 m i lengde, vurdert for minst av 6 amp, 250V, fremstilt av HAR ledning IEC 320 koplingsstykke på den ene kanten og på den andre kanten en plugg som har blitt godkjent i det landet hvor den siste brukeren befinner seg. Forsiktig ! BRUKSANVISNINGER FOR MONTERING FORSIKTIG: Disse modellene er beregnet til bruk i HORISONTAL stilling. VERTIKAL MONTERING må IKKE UTFØRES uten bruk av et Allied Telesyn vertikal monteringschassis som er spesiallaget til dette formål. FORSIKTIG: Luftventilene må ikke blokkeres og må ha fri tilgang til luft med romtemperatur for avkjøling. FORSIKTIG: Gummiføttene må IKKE fjernes fra produktet med mindre en Allied Telesyn vertikal monteringschassis er i bruk. DRIFTSTEMPERATUR Dette produktet har blitt fremstilt til bruk med maksimum romtemperatur på 50 grader celsius. ALLE LAND: Produktet må installeres i samsvar med de lokale og nasjonale elektriske koder. ENERGIA IRRADIADA Este produto foi testado e atende aos requisitos para dispositivos comerciais de Classe A nos E.U.A. Este produto foi testado e atende aos requisitos Vfg 243/1991 para dispositivos de Classe B na Alemanha Atenção Perigo ! SEGURANÇA AVISOS SOBRE CARACTERÍSTICAS ELÉTRICAS ATENÇÃO: PERIGO DE CHOQUE ELÉTRICO Para evitar CHOQUE ELÉTRICO, não retire a tampa. Não contém peças que possam ser consertadas pelo usuário. Este aparelho contém VOLTAGENS PERIGOSAS e só deve ser aberto por um técnico qualificado e treinado. Para evitar a possibilidade de CHOQUE ELÉTRICO, desconecte o aparelho da fonte de energia elétrica antes de conectar e desconectar os cabos da LAN. PERIGO DE CHOQUE CAUSADO POR RAIO PERIGO: NÃO TRABALHE no equipamento ou nos CABOS durante períodos suscetíveis de QUEDAS DE RAIO. CUIDADO: O CABO DE ALIMENTAÇÃO É UTILIZADO COMO UM DISPOSITIVO DE DESCONEXÃO. PARA DESELETRIFICAR O EQUIPAMENTO desconecte o cabo de alimentação. INSTALAÇÃO ELÉTRICO—AJUSTE AUTOMÁTICO DE VOLTAGEM Este produto ajustar-se-á automaticamente a qualquer voltagem que esteja dentro dos limites indicados no rótulo. ELÉTRICO—EQUIPAMENTOS DO TIPO CLASSE 1 DEVE SER FEITA LIGAÇÃO DE FIO TERRA PARA ESTE EQUIPAMENTO. O plugue deve ser conectado a uma tomada com ligação de fio terra. Tomadas sem ligação de fio terra podem transmitir voltagens perigosas a peças metálicas expostas. ELÉTRICO—AVISO SOBRE O CABO DE ALIMENTAÇÃO Use cabo de alimentação com comprimento máximo de 4,5 metros, com uma capacidade mínima de 6 amp e 250 V, fabricado de material para cabo HAR com conector moldado IEC 320 em uma extremidade e, na outra extremidade, um plugue aprovado para uso no país em questão . vii Cuidado ! INSTRUÇÕES DE INSTALAÇÃO CUIDADO: Este modelos foram projetados para funcionar na posição HORIZONTAL. NÃO DEVE SER EFETUADA INSTALAÇÃO VERTICAL sem o uso de um chassis de montagem vertical Allied Telesyn projetado para este fim específico. CUIDADO: As entradas de ar não devem ser bloqueadas e devem ter acesso livre ao ar ambiente para arrefecimento adequado do aparelho. CUIDADO: NÃO RETIRE os calços de borracha do produto a menos que esteja sendo usado um chassis de montagem vertical Allied Telesyn. TEMPERATURA DE FUNCIONAMENTO Este produto foi projetado para uma temperatura ambiente máxima de 50 graus centígrados. TODOS OS PAÍSES: Instale o produto de acordo com as normas federais e locais para instalações elétricas. ENERGIA RADIADA Este producto comercial ha sido probado y cumple con las normas requeridas en los EE. UU. para un dispositivo de Clase A. Este producto ha sido probado y cumple con los requisitos Vfg 243/1991 de Alemania para un dispositivo de Clase B. Advertencia Peligro ! SEGURIDAD AVISOS ELECTRICOS ADVERTENCIA: PELIGRO DE ELECTROCHOQUE Para evitar un ELECTROCHOQUE, no quite la tapa. No hay ningún componente en el interior al cual puede prestar servicio el usuario. Esta unidad contiene VOLTAJES PELIGROSOS y sólo deberá abrirla un técnico entrenado y calificado. Para evitar la posibilidad de ELECTROCHOQUE desconecte la corriente eléctrica que llega al producto antes de conectar o desconectar los cables LAN. PELIGRO DE RAYOS PELIGRO: NO REALICE NINGUN TIPO DE TRABAJO O CONEXION en los equipos o en LOS CABLES durante TORMENTAS DE RAYOS ATENCION: EL CABLE DE ALIMENTACION SE USA COMO UN DISPOSITIVO DE DESCONEXION. PARA DESACTIVAR EL EQUIPO, desconecte el cable de alimentación. INSTALACION ELECTRICO—AUTO-AJUSTE DE TENSION Este producto se ajustará automáticamente a cualquier tensión entre los valores máximos y mínimos indicados en la etiqueta. ELECTRICO—EQUIPO DEL TIPO CLASE 1 ESTE EQUIPO TIENE QUE TENER CONEXION A TIERRA. El cable tiene que conectarse a un enchufe con tierra debidamente instalado. Un enchufe que no está correctamente instalado podría ocasionar tensiones peligrosas en las partes metálicas están expuestas. ELECTRICO—ADVERTENCIA SOBRE EL CABLE Use un cable eléctrico con un máximo de 4,5 metros de largo, con una capacidad mínima de 6 amperios, 250 V, hecho de cable HAR, con el conector moldeado IEC 320 en un extremo y con un enchufe que está aprobado por el país de uso final en el otro. Attencion ! INSTRUCCIONES DE MONTAJE ATENCION: Estos modelos están diseñados para operar en posición HORIZONTAL. NO SE DEBEN MONTAR VERTICALMENTE sin el uso de un chasis de montaje vertical de Allied Telesyn que se ha diseñado para este fin. ATENCION: Las aberturas para ventilación no deberán bloquearse y deberán tener acceso libre al aire ambiental de la sala para su enfriamiento. ATENCION: NO separe las patas de goma del producto a menos que se esté usando un chasis de montaje vertical de Allied Telesyn. TEMPERATURA REQUERIDA PARA LA OPERACIÓN Este producto está diseñado para una temperatura ambiental máxima de 50 grados C. PARA TODOS LOS PAÍSES: Monte el producto de acuerdo con los Códigos Eléctricos locales y nacionales. ENERGIUTSTRÅLNING Denna handelsprodukt har testats och befunnits vara i enlighet med U.S.A.s krav för klass A utrustning. Denna produkt har testats och befunnits vara i enlighet med Tysklands Vfg 243/1991 krav för klass B utrustning. Varning Fara ! SÄKERHET TILLKÄNNAGIVANDEN BETRÄFFANDE ELEKTRICITETSRISK: RISK FÖR ELEKTRISK STÖT För att undvika ELEKTRISK stöt, ta ej av locket. Det finns inga delar inuti som behöver underhållas. Denna apparat är under HÖGSPÄNNING och får endast öppnas av en utbildad kvalificerad tekniker. För att undvika ELEKTRISK STÖT, koppla ifrån produktens strömanslutning innan LAN-kablarna ansluts eller kopplas ur. FARA FÖR BLIXTNEDSLAG ARBETA EJ på utrustningen eller kablarna vid ÅSKVÄDER. VARNING: NÄTKABELN ANVÄNDS SOM STRÖMBRYTARE FÖR ATT KOPPLA FRÅN STRÖMMEN, dra ur nätkabeln. INSTALLATION ELEKTRISKT—AUTOMATISK SPÄNNINGSJUSTERING Denna produkt justeras automatiskt till alla spänningar inom omfånget som indikeras på produktens märkning. viii ELEKTRISKT— TYP KLASS 1 UTRUSTNING DENNA UTRUSTNING MÅSTE VARA JORDAD. Nätkabeln måste vara ansluten till ett ordentligt jordat uttag. Ett felaktigt uttag kan göra att närliggande metalldelar utsätts för högspänning. Apparaten skall anslutas till jordat uttag, när den ansluts till ett nätverk. ELEKTRISKT—ANMÄRKNING BETRÄFFANDE KABELN Använd en kabel med maximum längd 4,5 meter och minimum 6 amp nominal, 250V, av HAR kabelfabrikat med ett specialutformat IEC 320-kontaktdon i ena änden och i den andra en plugg som godkänts i landet där produkten används. Varning ! MONTERINGSINSTRUKTIONER VARNING: Dessa modeller är konstruerade för användning i HORISONTALLÄGE. VERTIKALMONTERING får EJ UTFÖRAS utan att ett Allied Telesyn specialkonstruerat vertikalt monteringschassi används. VARNING: Luftventilerna får ej blockeras och måste ha fri tillgång till omgivande rumsluft för avsvalning. VARNING: Ta ej bort gummifötterna från produkten om inte ett Allied Telesyn vertikalt monteringschassi används. DRIFTSTEMPERATUR Denna produkt är konstruerad för rumstemperatur ej överstigande 50 grader Celsius. ALLA LÄNDER: Installera produkten i enlighet med lokala och statliga bestämmelser för elektrisk utrustning. ix Table of Contents Electrical Safety and Installation Requirements ................................................ iii Chapter 1 Overview ..........................................................................................................................1 CentreCOM AT-810SL Multiport Transceiver Fanout ............................................................................. 1 AT-810SL 8 Port Fanout, Slim-line Chassis.......................................................................................... 1 Features ...................................................................................................................................................... 2 Chapter 2 Installation ..................................................................................................................... 3 Requirements.................................................................................................................................................... 3 Procedure .......................................................................................................................................................... 3 Power........................................................................................................................................................... 4 Chapter 3 Operation ........................................................................................................................ 5 Station Port Configuration ............................................................................................................................. 5 LED Status Indicators .................................................................................................................................... 6 Front Panel ................................................................................................................................................. 6 Back Panel .................................................................................................................................................. 8 Port Connectors................................................................................................................................................ 8 Chapter 4 Configuration ................................................................................................................ 11 Cascading .................................................................................................................................................. 11 Appendix A IEEE 802.3 Quick Primer ............................................................................................13 AUI Drop Cables............................................................................................................................................ 13 10BASE-T ....................................................................................................................................................... 13 Thin (10BASE2) Ethernet ............................................................................................................................ 14 Thick (10BASE5) Ethernet .......................................................................................................................... 14 Propagation ..................................................................................................................................................... 14 Four Repeater Rule....................................................................................................................................... 14 xi Appendix B Pin Assignments ........................................................................................................... 15 Notes ............................................................................................................................................................... 15 Appendix C Glossary .......................................................................................................................... 17 Appendix D Technical Support Fax Order ...................................................................................23 Incident Summary ......................................................................................................................................... 23 Appendix E CentreCOM AT-810SL Manual Feedback xii ...............................................................25 Chapter 1 Overview CentreCOM AT-810SL Multiport Transceiver Fanout AT-810SL 8 Port Fanout, Slim-line Chassis The CentreCOM Multiport Transceiver Fanouts are part of a family of multiport transceivers for use with Ethernet Local Area Networks (LANs). These units can provide network managers with either small standalone networks or they can act as a concentrator, grouping several devices onto a single tap on an Ethernet network. The CentreCOM Multiport Transceiver Fanouts connect up to 8 Data Terminal Equipment (DTE) workstations, using standard Attachment Unit Interface (AUI) “Drop” cables in one of 3 switch-selectable configurations. When “Remote” operation is selected, the unit can attach to an existing transceiver using an AUI cable up to 50 meters (164 ft.) in length. In “Local” operation, the network manager has a choice between operation with or without Signal Quality Error (SQE)/Heartbeat Test. With the flip of a switch, the network manager can choose to support or not support SQE Test, or segment the attached nodes from the main network while still allowing local communication between workstations. The CentreCOM Multiport Transceiver Fanout interface is compliant with the IEEE 802.3 specification and compatible with Ethernet Version 1.0 and 2.0. When used in Remote Mode, the electrical characteristics of the transceiver are passed transparently through these multiport transceiver fanouts to the attached nodes as if each unit was attached with its own transceiver. When in Remote Mode, SQE should be OFF. Up to 64 stations can be cascaded together through the AT-810SL. This permits the workstations to be up to 150 meters (492 ft.) from the backbone cable and up to 200 meters (656 ft.) apart. By cascading the CentreCOM Multiport Transceiver Fanouts, over a thousand nodes can be attached to a single backbone cable without requiring repeaters or additional internetworking devices. 1 Overview The AT-810SL has front panel status and diagnostic indicators that provide “On Line” and “Transmit” status for each port. Figure 1 shows the front panel. Packet “Receive” and “Collision” indicators are available for the Transceiver Ports as well as the Station Port. The front panel “System Power” LED indicates when power is applied to the AT-810SL and the “Station Power” LED indicates when power is applied to any of the Transceiver Ports. On the back of the AT-810SL are redundant LEDs indicating the application of “Station Power” for each Transceiver Port, and one redundant LED indicating “System Power.” Allied Telesyn STATION PORT CentreCOM 810SL IEEE 802.3/ETHERNET MULTIPORT TRANSCEIVER FANOUT PORT 1 2 PORT 3 2 3 4 5 6 7 8 RECEIVE ON LINE RECEIVE ON LINE STATION POWER COLLISION TRANSMIT COLLISION TRANSMIT PORT 5 PORT 7 SYSTEM POWER SQE TEST SWITCH LOCAL/REMOTE SWITCH OFF ON LOCAL O I REMOTE Allied Telesyn CentreCOM 810SL IEEE 802.3/ETHERNET Figure 1: AT-810SL Front and Back Panel Features TRANSCEIVER PORT 1 SYSTEM POWER MULTIPORT TRANSCEIVER FANOUT PORT 2 ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ PORT 4 PORT 6 PORT 8 STATION POWER IEEE 802.3 compliant, Ethernet Version 1.0 and 2.0 compatible Cascades up to 64 ports Standalone network or attach to an Ethernet backbone Switch-selectable SQE Test; local and remote operation Slim-line chassis occupies just one slot in a 19 inch rack On Line, Transmit and Transceiver Power LEDs per port System Power and Station Power LEDs Receive and Collision LEDs Standalone or rack mountable One year warranty Chapter 2 Installation Requirements Attention Before installing AT-810SL Multiport Transceiver Fanouts, read the ! electrical safety and installation requirements starting on page i. Before installing the AT-810SL Multiport Transceiver Fanout, ensure that the following requirements are met: ❑ ❑ ❑ ❑ ❑ The network cabling is properly configured. Power connections are made at the back panel. The AT-810SL repeater has a universal power supply that will accept either 110 or 220 VAC at 50-60 Hz. The appropriate IEEE 802.3 AUI standard transceiver cables are available. To prevent equipment damage from overheated components, adequate air flow must be maintained. Before turning on the power, verify that both the air intake vents on each side of the chassis are free of obstructions. For Remote Mode operation, a CentreCOM 100, 200, 150, 250, 270, or 470 Series external transceiver or other IEEE 802.3 Media Attachment Unit (MAU) may be required. Contact your supplier for the appropriate model number. Procedure IEEE 802.3 10BASE5 (IEC/ISO 8802-3) conventions and standards place certain limitations on network configurations. Careful planning before tapping onto the network will help avoid unnecessary problems. The most important consideration is the transceiver cable length. When operating in Remote Mode, please ensure that the AT-810SL is within 50 meters (164 ft.) of the MAU. In either Local or Remote Mode, DTEs must also be located within 50 meters (164 ft.) of the AT-810SL. 3 Installation Once all the cables have been laid and the AT-810SL is placed in the location of your choice, you are ready to begin the actual connections. (Except for monitoring the LEDs, there is no benefit in being able to physically see the AT-810SL during routine operation; the unit may therefore be installed in any location with adequate ventilation, temperature control and power connections.) Power The CentreCOM AT-810SL Multiport Transceiver Fanout is designed for desktop or rackmount installation with optional Rack Mount Kits AT-RKMT2 and AT-RKMT-3. AT-810SL requires a 100-240 VAC power source with a line frequency range from 50 Hz-60 Hz. The AT-810SL is equipped with an IEC-320/CEE-22 standard power input connector on its back panel. One end of the power cord should have a receptacle to fit this type of connector. The other end should be fitted with the standard power cord plug for the country in which the unit will be operated. No power cord is provided for European style AC outlets. Obtain the appropriate cord from your equipment vendor. 4 Chapter 3 Operation Station Port Configuration The AT-810SL is designed to require a minimum of operator attention during routine operation. The station port configuration allows access, via an AUI cable and transceiver, to an Ethernet coaxial cable or fiber optic cable. This port is only used when the AT-810SL is set in Remote Mode. Once the unit has been installed and set for your particular configuration, it will be transparent to the users and to the network. Two switches are provided on the back panel, allowing selection of Local or Remote Mode and SQE Test ON or OFF. Local Mode allows operation of the equipment linked to the AT-810SL as a standalone “mini-network” giving the option to have the SQE Test ON or OFF, depending on the application. In the Local Mode the Station Port is disconnected from the Transceiver Ports. In the Remote Mode (i.e., access to an external transceiver attached to an Ethernet coaxial or fiber optic cable), the AT-810SL is a “pass-through” unit with the SQE Test provided by the transceiver connected to the Ethernet cable. Figure 2 shows the Station Port configuration. Note When used in Remote Mode, the SQE Test switch should be OFF. SYSTEM POWER SQE TEST SWITCH LOCAL/REMOTE SWITCH OFF ON LOCAL O I REMOTE STATION Figure 2: Station Port 5 Operation LED Status Indicators The AT-810SL has many LEDs to aid in installation and troubleshooting should any problems occur. They also serve to verify correct transceiver operation at a glance. Below is a description of their location, grouping and functionality. Refer to Figure 3 for location of the System Power and Station Power. Front Panel System Power—When lit, this LED indicates correct AC voltage applied and internal power supply is operational. Station Power— When lit, this LED indicates that power (+12 volts) is applied to Pin-13 of the Station Ports DB15 connector by the MAU backbone transceiver via the AUI cable. SYSTEM POWER Figure 3: Front Panel Power Indicators STATION POWER Refer to Figure 4 for location of Station Port indicators. Note This group of LEDs is associated only with the Station Port and as such are only active when the AT-810SL is configured for Remote operation via the two-position Station Port configuration switch. On Line —When lit, this LED indicates that the Mode Selection switch is in the Remote position. This is for configuration status only. Transmit —When lit, this LED indicates a packet is being received into any of the eight Transceiver Ports and transmitted out through the Station Port. Receive— When lit, this LED indicates a packet is being received into the Station Port and is being routed to the eight Transceiver Ports. Collision—When lit, this LED indicates a Collision or SQE occurrence on the segment to which the Station Port is connected. 6 CentreCOM AT-810SL Multiport Transceiver Fanout STATION PORT RECEIVE ON LINE COLLISION TRANSMIT Figure 4: Station Ports Refer to Figure 5 for the location of the Transceiver Ports. On Line—When lit, these LEDs indicate that the corresponding Transceivers Port is connected through an AUI cable to a DTE device, and that the DTE is powered-up and On Line. Transmit—When lit, these LEDs indicate that the corresponding Transceivers Port is receiving a packet and transmitting it to the other seven Transceiver Ports. If in Remote Mode, this packet will also be sent out through the Station Port. Receive—When lit, this LED indicates that each of the Transceiver Ports is presenting a packet to its associated DTE. Only one LED is required to represent this function, as all of the Transceiver Ports are effectively parallel for this function. Collision—When lit, this LED indicates that a Collision or SQE has occurred on or between one or more of the Transceiver Ports. This is not a latched condition, so if this LED is steadily lit, a hard failure or a configuration problem with one of the DTE’s is occurring, or an inordinate number of Collisions are occurring, indicating overload and warranting further attention. Collisions between the Transceiver Ports themselves will not be propagated through to the Station Port, and thus will not impede network activity on the Remote Segment. TRANSCEIVER PORT 1 2 3 4 5 6 7 8 RECEIVE ON LINE COLLISION TRANSMIT Figure 5: Transceiver Port 7 Operation Back Panel Refer to Figure 6 for the location of the Status Indicators. On Line(s)—Each Transceiver Port has an associated On Line LED. When lit, these LEDs indicate that the DTE, connected to the related port through the AUI cable, has power applied to it. These will be lit/unlit regardless of the AT-810SL’s operational status and are provided so a DTE’s “in use” status can be ascertained before disconnection of its cable. System Power—When lit, this LED indicates AC power is correctly applied and the internal power supply is operational. This indicator is redundant with the System Power LED on the front panel, it is provided for ease of viewing from the back in rack mount applications. PORT 1 PORT 3 PORT 5 PORT 7 SYSTEM POWER SQE TEST SWITCH LOCAL/REMOTE SWITCH OFF ON LOCAL O I REMOTE Allied Telesyn CentreCOM 810SL IEEE 802.3/ETHERNET Figure 6: Back Panel Status Indicators MULTIPORT TRANSCEIVER FANOUT PORT 2 PORT 4 PORT 6 PORT 8 STATION POWER Port Connectors The Transceiver Port connectors and the Station Port connector are located on the back panel. See Figure 7. Transceiver Ports (x8) AUI Cable Connections to DTE Workstations PORT 1 PORT 3 PORT 5 PORT 7 SYSTEM POWER SQE TEST SWITCH LOCAL/REMOTE SWITCH OFF ON LOCAL O I REMOTE Allied Telesyn CentreCOM 810SL IEEE 802.3/ETHERNET MULTIPORT TRANSCEIVER FANOUT PORT 2 PORT 4 PORT 6 PORT 8 STATION POWER Station Ports (x1) AUI Cable Connections to MAU Transceiver on coax Figure 7: Port Connectors ! Caution! All screws and mounting hardware used in these units use International Standard metric thread. Do not attempt to replace with another type thread. Vorsicht! Alle bei diesen Geräten verwendete Schrauben und Montageteile weisen der internationalen Norm entsprechende metrische Gewinde auf. Keine Gewinde eines anderen Typs verwenden. Forsigtig! Alle skruer og monteringsdele anvendt i disse elementer anvender International Standard metrisk tråd. Undlad at forsøge at erstatte med en anden type tråd. Opgelet! Alle schroeven en bevestigingshardware in deze toestellen zijn uitgerust met International Standard metrieke schroefdraad. Probeer niet deze te vervangen door een ander type schroefdraad. 8 CentreCOM AT-810SL Multiport Transceiver Fanout Attention! Toutes les vis et autre matériel de montage de ces unités emploient le filetage métrique international standard. Ne pas essayer de les remplacer par un autre type de filetage. Varovaisuutta noudatettava! Kaikissa näissä yksiköissä käytettävissä ruuveissa ja metalliosissa käytetään kansainvälisen standardin mukaisia metrisiä kierteitä. Älkää yrittäkö korvata niitä toisen tyyppisillä kierteillä. Avvertenza! Tutte le viti ed i materiali di montaggio utilizzati in questi apparecchi utilizzano il sistema metrico standard internazionale di filettatura. Non provare a sostituirli con pezzi che abbiano un altro tipo di filettatura. Forsiktig! Alle skruene og monteringsdelene som brukes i disse enhetene bruker metrisk-tråd av internasjonal standard. Prøv ikke åerstatte noe med en annen type tråd. Alerta! Todos os parafusos e ferragens de montagem utilizados nestas unidades usam roscas de padrão métrico ISO. Não tente substituir por outro tipo de rosca. Precaución! Todos los tornillos y piezas de montaje que se usan en estas unidades poseen rosca métrica de normas internacionales. No efectuar reemplazos con otro tipo de rosca. Varning! Alla skruvar och monteringsdelar, som används med denna utrustning, utnyttar internationella metriska standardgängor. Använd aldrig gängor av annan typ. 9 Chapter 4 Configuration The CentreCOM Multiport Transceiver Fanout can be used to expand the number of allowable stations per transceiver in an Ethernet LAN in the following ways: ❑ ❑ ❑ ❑ Cascading Additional stations can be attached to an Ethernet coaxial cable segment which may have limited taps (MAUs) available. Where numerous stations are in close proximity, the number of transceivers connected to an Ethernet coaxial cable segment can be reduced. The number of stations per Ethernet coaxial cable segment can be increased, which can reduce the number of segments required. One AT-810SL can be used to operate as an independent network of up to eight DTEs (workstations). The AT-810SL can be configured in a cascaded mode. Utilizing nine multiport transceivers in this configuration allows a maximum of 64 DTE (workstations). A cascaded series of multiport transceivers can be operated as an independent network, or it can be connected to coaxial cable segment through a CentreCOM 100, 200, 150, 250, 270, or 470 Series transceiver. 11 Configuration The configuration below demonstrates cascading of nine CentreCOM Multiport Transceiver Fanouts to provide up to 64 DTE (workstation) connections from one MAU tap on a coaxial backbone. Enterprise LAN Backbone Optional Backbone Connection Allied Telesis STATION PORT TRANSCEIVER PORT 1 CentreCOM 810SL 2 3 4 5 6 7 8 SYSTEM POWER RECEIVE ON LINE RECEIVE ON LINE STATION POWER COLLISION TRANSMIT COLLISION TRANSMIT Up To Eight Units May Be Cascaded Allied Telesis CentreCOM 810SL STATION PORT 12 2 3 4 5 6 7 8 RECEIVE ON LINE RECEIVE ON LINE COLLISION TRANSMIT COLLISION TRANSMIT Up To Eight DTEs Figure 8: AT-810SL Configuration Allied Telesis TRANSCEIVER PORT 1 SYSTEM POWER STATION POWER CentreCOM 810SL STATION PORT TRANSCEIVER PORT 1 2 3 4 5 6 7 8 SYSTEM POWER RECEIVE ON LINE RECEIVE ON LINE STATION POWER COLLISION TRANSMIT COLLISION TRANSMIT Up To Eight DTEs Appendix A IEEE 802.3 Quick Primer AUI Drop Cables AUI or Drop cables can be no longer than 50 meters (164 ft.) each. Attachments may be made only to the cable ends at the 15-pin D-shell connector. AUI Drop cables may have a maximum 257 ns propagation delay, as used for computing the worst case propagation delay of a cable system. AUI cable propagation delay is approximately 5.13 ns/meter. This cable internally consists of four shielded twisted pair wires with an overall shield and drain wire; a 15-pin D-shell male connector at one end and a 15-pin D-shell female connector at the other end. Cable impedance is nominally 78 Ω. The AUI cable typically connects a transceiver attached to a coaxial segment to a DTE (workstation). 10BASE-T 10BASE-T UTP media was implemented to reduce Ethernet wiring costs. UTP wiring is installed in most buildings for telephone systems. Care must be taken to ensure the UTP wiring used for 10BASE-T is able to carry the high Ethernet data rates before a 10BASE-T network solution is implemented. Unlike coaxial Ethernet, 10BASE2 and 10BASE5, 10BASE-T UTP is point-to-point wiring. Typically, one end is connected to an Ethernet 10BASE-T Network Interface Controller (NIC) or transceiver (MAU) and the other end is connected to a 10BASE-T hub (repeater). Straight-through cabling pin-out is used for hub-to-MAU connections. Hub-to-hub and MAUto-MAU connections are allowed using a UTP cable with a cross-over function crossing TD+ and TD- with RD+ and RD- signals. No other attachments are allowed along the length of the UTP wire; however, wiring patch panels and punch-down blocks are allowed for interconnecting segments. The cable should be Level 3 UTP, 100 Ω impedance, 22 to 26 AWG, and should not exceed 100 meters (328 ft.) in length from one end to the other. 13 IEEE 802.3 Quick Primer Thin (10BASE2) Ethernet When configuring thin coax segments, IEEE 802.3 specifications allow 30 or fewer MAU attachments per cable segment spaced at no less than 0.5 meters (1.64 ft.) between each attachment. The thin (10BASE2) cable length can not exceed 185 meters (606 ft.) per thin (10BASE2) cable segment. The worst case propagation delay for a 185 meter (606 ft.) thin Ethernet segment is 950.9 ns. The propagation delay for thin (10BASE2) Ethernet cable is 5.14 ns/ meter. Both ends of the segment must be terminated with a 50 Ω termination with a power rating of 0.5 watts or greater. The segment shield must be grounded only at one point on the cable. Thick (10BASE5) Ethernet When configuring thick coax segments, IEEE 802.3 specifications allow 100 MAU attachments or less, spaced at multiples of 2.5 meters (8.2 ft.) measured accurately from the cable end (50 Ω terminator included). The thick cable segment cannot exceed 500 meters (1640 ft.) in length. Worst case end to end propagation delay of a thick coax segment is 2165 ns. Propagation delay of thick Ethernet coax is calculated at 4.33 ns/meter. Both ends of the segment must be terminated with a 50 Ω termination with a power rating of 0.5 watts or greater. Earth grounding of the segment shield must take place only at one point on the cable. Propagation Propagation delay is the time it takes a signal to travel from the input of a system component to the output. Propagation delay is usually measured in nanoseconds. IEEE 802.3 has specific propagation delay maximums for the Ethernet components. Cable length plays a major role in propagation delay. i.e, a 50 meters (164 ft.) AUI cable has a maximum propagation delay of 257 ns. The propagation delay of cable is dependent on length and velocity factor of the cable type. Round-trip propagation delay through-out the entire cable system, from farthest ends, may not exceed 51.7 µs, ± 4 µs. Four Repeater Rule Up to four repeater units may be connected for a total of five segments provided that two of the segments are link segments. Link segments have no MAU attachments. If all segments are coax segments, having MAU attachments, then a maximum of two repeater units and three segments are allowed. 14 Appendix B Pin Assignments Notes Control In Shield (CI-S) is tied internally to the connector shell's Protective Ground (PG) and is capacitively coupled to ground through a .01 µFD capacitor. Control In pair [(CI-A) and (CI-B)] are sometimes referred to as “Collision.” This signal pair carries messages from the MAU to the DTE in a Manchester encoded format to inform the DTE of the following: Message Description mau_available Mau is ready to output data to coaxial cable mau_not_available MAU is not ready to output data to coaxial cable signal_quality_error MAU has detected an error on data input (collision or self-test of error detection circuitry) Data Out pair [(DO-A) and (DO-B)], from the DTE to the MAU, carries the actual data to be transmitted to the network. It is in the form of two messages “output,” and “output_idle.” The message “output” carries a Manchester encoded logic 1 or logic 0 bit, and the “output_idle” message informs the MAU that no more data will be output. Data In pair [(DI-A) and (DI-B)], from the MAU to the DTE, carries the actual data received from the network. It is in the form of two messages “input” and “input_idle.” The message “input” carries an Manchester encoded logic 1 or a logic 0 bit, and the “input_idle” message informs the DTE there is no more input data. Control Out pair [(CO-A) and (CO-B)], and the Control Out Shield (CO-S) are optional under the IEEE 802.3 specification and as such are uncommon in the real world. These signals are not required by any standard products on the market, and are not implemented in the AT-810SL. Conductive Shield, no internal connection by AT-810SL, will be grounded internally by DTE device. 15 Pin Assignments Voltage Common (Vc) is the ground return path for the Voltage Plus (Vp) supply voltage (12v-15v 6%) sourced by the DTE to power the MAU. Voltage Plus is optional under the IEEE 802.3 specification but is typically provided by the majority of DTE devices, and as such is used to light the “On Line” LED status indicators on the back panels. 16 Appendix C Glossary 10BASE2—Also called thinnet or CheaperNet, 10BASE2 is a 10 MHz, baseband, 185 meters (606 ft.) maximum coaxial segment. Cable impedance is 50 Ω. 10BASE5—Also called thick Ethernet, 10BASE5 is a 10 MHz, baseband, 500 meters (1639 ft.) maximum coaxial segment. The cable is commonly referred to as yellow cable. Cable impedance is 50 Ω. Thick Ethernet cable is typically used as a trunk or backbone path of the network. 10BASE-T—IEEE 802.3 UTP Ethernet. Using low cost Level 3 or better UTP wiring, 100 meters (328 ft.) of point-to-point link segments are possible. Uses RJ45 connectors and sometimes 50-pin AMP connectors to a patch panel. 50-PIN TELCO (RJ21)—This connector is very common in 10BASE-T wiring. As opposed to the RJ45 connector, the 50-pin Telco connector concentrates up to 12 UTP connections onto one connection. This concentration of UTP ports is later broken out for connection to a punchdown block inside a building’s wiring closet. 50-pin Telco connections provide a very clean, uncluttered interface to the building’s wiring. ATTACHMENT UNIT INTERFACE (AUI)—This is the cable connection from a MAU (transceiver) to a DTE (typically a workstation) consisting of a 15 conductor twisted pair cable of 50 meters (164 ft.) maximum length. BASEBAND COAXIAL SYSTEM—A system whereby information is directly encoded and impressed on the coaxial transmission medium. At any point on the medium, only one information signal at a time can be present without disruption. BAYONET NUT COUPLE (BNC) CONNECTOR—A 10BASE2 thin coax connector with push-on BNC locking lug that quickly locks into place with a half twist. BIT RATE (BR)—This is the rate of data throughput on the medium in bits per second. Ethernet specifies 10 million bits per second. BRANCH CABLE—The AUI cable interconnecting the DTE and MAU system components also known as a Drop cable. 17 Glossary BIT TIME—The duration of one bit symbol (1/BR). Ethernet specifies a bit time of 100 ns. COAX SEGMENT—A segment of Ethernet cable that contains MAU. CARRIER SENSE MULTIPLE ACCESS with COLLISION DETECT (CSMA/CD)—This is the access method employed by IEEE 802.3 LAN transceivers, by which multiple stations compete for use of the transmission medium (coax cable) for data packet transmission, and provides for a level of error detection should that transmission be corrupted or impeded by contention for the transmission medium. CARRIER SENSE—In a LAN, an ongoing activity of a data station to detect whether another station is transmitting. COAXIAL CABLE—A two conductor (center conductor, shield system), concentric, constant impedance transmission line used as the trunk medium in the baseband system. COAXIAL CABLE SEGMENT—A length of coaxial cable sections and coaxial connectors, and terminated at each end in its characteristic impedance. COLLISION—An unwanted condition that results from concurrent transmissions on the physical medium. COLLISION PRESENCE—A signal provided by the PLS to the PMA sublayer (within the physical layer) to indicate that multiple stations are contending for access to the transmission medium. COMPATIBILITY INTERFACE—The MDI coaxial cable interface and the AUI branch cable interface, the two points at which hardware compatibility is defined to allow connection of independently designed and manufactured components to the baseband transmission system. CROSS-OVER—Wiring is used when connecting a 10BASE-T MAU to another 10BASE-T MAU or a 10BASE-T hub to another 10BASE-T hub. For example, one 10BASE-T MAU would have the TD pair on the same pins as another 10BASE-T MAU. If pins were wired straight, there would be two transmitters on one pair with no receiver. Therefore, the cross-over cable crosses the TD pair with the RD pair of UTP cable connecting the TD pins on one end to the RD pins at the other end. D-SUB CONNECTOR—The AUI cable uses 15-pin D-sub connectors. “D” refers to the shape of the connector shell. Also called miniature D, DB15, or DIX connectors. DATA COMMUNICATION EQUIPMENT (DCE)—In RS232 specification a unit, such as a modem, for connecting a DTE to other equipment. A repeater connected to a terminal or workstation for OMEGA LOCAL management use is wired as a DCE. DATA TERMINAL EQUIPMENT (DTE)—In RS232 specification a unit typically at the end of a segment. The DTE could be an Ethernet workstation, repeater, or bridge. 18 CentreCOM AT-810SL Multiport Transceiver Fanout DEPARTMENT CONCENTRATOR—Hub which provides a large number of workstation connections. The term, department concentrator, refers to multiple repeaters housed in an AT-36C8 chassis. See Hub/Repeater, Repeater. DIX CONNECTOR—See D-Sub Connector HARMONICA ADAPTER—This adapter provides a simple way to convert the 50-pin Telco connection to RJ45 connections. HEARTBEAT—See SQE HUB to HUB WIRING—See Hub to MAU Wiring HUB to MAU WIRING—UTP cables for 10BASE-T hub-to-MAU or Network Interface Controller (NIC) cards are wired straight-through. An RJ45 receptacle at the hub would wire pin to pin to the RJ45 receptacle at the MAU. HUB/REPEATER—A hub is a central signal distributor. It is used in a wiring topology consisting of several point-to-point segments originating from a central point. The term hub is often used interchangeably with the term repeater. Multiport 10BASE-T, 10BASE2 and fiber optic (10BASE-FL, FOIRL) repeaters are considered hubs. See Repeater. HOUSE WIRING—House wiring is the existing wiring inside a building. This wiring generally originates from one or more wiring closets such as a telephone room. Some older buildings may have wiring unsuitable for 10 Megabit data rates. In these circumstances, it is recommended that the wiring is tested with a 10BASE-T signal/wire tester. IMPEDANCE—An electrical characteristic of a circuit dealing with the combination of the AC and DC resistance and the appearance of that resistance to attached circuits. JABBER LOCK-UP—The MAU’s ability to automatically inhibit the transmit data from reaching the medium if the transmit data time length exceeds 150 ms duration. This protects the medium from being overrun with data packets from a possibly defective device. JAM—This is a term used to describe the collision reinforcement signal output by the MAU onto the transmission medium if the transmit data time length exceeds 150 µs duration. This protects the medium from being overrun with data packets from a possibly defective device. JITTER—The fluctuation of the data packet in respect to a standard clock cycle. Jitter is undesirable and must be minimized. LINK SEGMENT—The link segment of coaxial cable is a segment which has no MAU devices but links two LAN devices together such as repeaters. LINK TEST—In 10BASE-T Ethernet there is a link test function that validates the UTP link. This consists of a pulse transmitted from point A on one pair and validated at point B. Point B also transmits a pulse on the second pair to be validated by point A. These pulses occur during media idle states (in between packets). 19 Glossary MANAGEMENT AGENT—Software that is used to view hub activity and set hub variables. MAU—See Medium Attachment Unit MAU to MAU, HUB to HUB WIRING—10BASE-T MAU to MAU or hub to hub wiring generally requires a cross-over cable located somewhere along the UTP cable run. This may commonly occur at the punch-down block or between the RJ45 wall receptacle and the workstation. MAU/TRANSCEIVER—An Ethernet transceiver is a MAU. A 10BASE-T MAU interfaces the UTP media to an AUI port on a workstation, repeater, bridge, or other Ethernet devices. MDI—See Medium Dependent Interface MEDIUM ATTACHMENT UNIT (MAU)—In a LAN, a device used in a data station to couple the DTE to the transmission medium. MEDIUM DEPENDENT INTERFACE (MDI)—The mechanical and electrical interface between the trunk cable medium and the MAU. N-SERIES—A barrel shaped, threaded connector used on 10BASE5 (thick Ethernet) coaxial cable. PATCH PANEL—A 10BASE-T patch panel may be between a punch-down block and UTP workstation. The patch panel generally has a female RJ45 connector on the front for each workstation and a Telco (RJ21) connector on the back, which are wired to a punch-down block. This provides a convenient way for the installer or network manager to connect the hub 10BASE-T ports into the desired building locations. PHYSICAL MEDIUM ATTACHMENT (PMA)—The portion of the MAU that contains the functional circuitry. PHYSICAL SIGNALING (PLS)—That portion of the physical layer contained within the DTE that provides the logical and functional coupling between MAU and data link layers. POLARITY CORRECTION—Many 10BASE-T UTP ports have a Polarity Correction function. If the UTP wiring has RD- and RD+ inadvertently crossed, the polarity correction function will sample the signal and electrically swap the wires. If the TD- and TD+ wires are crossed, the correction would occur at the MAU on the other end of the UTP link. This occurs within a single pair and should not be confused with the cross-over cable. PROPAGATION DELAY—The time it takes a signal to travel from the input of a system component to the output. Usually measured in nanoseconds. IEEE 802.3 has specific propagation delay maximums for computing propagation budgets when designing a LAN. Cable length plays a major role in propagation delay. [i.e, a 50 meters (164 ft.) AUI cable has a maximum allowable propagation delay of 257 ns.] The propagation delay of cable is dependent on length and velocity factor of the cable type. There are also propagation delays associated with electronics attached to the system. 20 CentreCOM AT-810SL Multiport Transceiver Fanout PUNCH-DOWN BLOCK—The punch-down block is the wiring panel where the house wiring from the building’s offices terminates. This is where many 10BASE-T hubs would be located. Wiring installers use a special punch-down tool to insert the UTP wire for data and voice applications. REPEATER—A device used to extend the length, topology, or interconnectivity of the physical medium beyond that imposed by a single segment, up to the maximum allowable end-to-end trunk transmission line length. Repeaters perform the basic actions of restoring signal amplitude, waveform and timing applied to normal data and collision signals. RJ45—This connector is a 10BASE-T standard for connecting UTP cabling. They are inexpensive and easy to install onto UTP cable. SIGNAL QUALITY ERROR (SQE)—Also referred to as Collision or Collision Presence. This occurs when two devices attempt to transmit at the same time which is an illegal condition. SQE TEST—Commonly referred to as Heartbeat, is a special 802.3 signal sent by the MAU to the DTE to test the collision detection function. Some DTE want SQE and others do not. Repeaters do not want SQE Test. THICK ETHERNET—See 10BASE5 THIN ETHERNET—See 10BASE2 TRUNK CABLE—The trunk coaxial cable system. UNSHIELDED TWISTED PAIR (UTP)—A cable used in 10BASE-T wiring that consists of at least two twisted pairs of 22 to 26 AWG wire. The pairs should have at least 3 twists per foot and have an impedance of 100 Ω. Level 3 and Level 4 UTP cable generally fits these criteria. 21 Appendix D Technical Support Fax Order Name ___________________________________________________________________ Company ________________________________________________________________ Address _________________________________________________________________ City ____________________State/Province____________ Zip/PostalCode __________ Country _________________ Phone __________________Fax ____________________ Incident Summary Model number of Allied Telesyn product I am using _____________________________ Firmware release number of Allied Telesyn product _____________________________ Other network software products I am using (e.g., network managers) ________________________________________________________________________ Brief summary of problem __________________________________________________ ________________________________________________________________________ Conditions (List the steps that led up to the problem.) ___________________________ ________________________________________________________________________ ________________________________________________________________________ ________________________________________________________________________ Detailed description (Please use separate sheet) Please also fax printouts of relevant files such as batch files and configuration files. Technical Support Fax Numbers: Asia (+65)-383-2079 Singapore, Taiwan, Thailand, Malaysia, Indonesia, Korea, Hong Kong, Philippines, China, India France France, Belgium, Luxembourg, Holland, Italy, Spain, Australia, New Zealand, Greece, Middle East, Africa, South America (+33)-1-6928-3749 Germany Germany, Switzerland, Austria, Eastern Europe (+49)-30-435-70-650 North America United States, Canada, Mexico 206-481-3790 United Kingdom United Kingdom, Denmark, Norway, Sweden, Finland, Iceland (+44)-1-865-390-002 23 Appendix E CentreCOM AT-810SL Manual Feedback Please tell us what additional information you would like to see discussed in the manual. If there are topics you would like information on that were not covered in the manual, please photocopy this page, answer the questions and fax or mail this form back to Allied Telesyn. The mailing address and fax number are at the bottom of the page. Your comments are valuable when we plan future revisions of the manual. On a scale of 1 to 10 (10 being most important), rate the importance of the following topics in this manual: Hardware Installation Diagnostics SNMP Software IEEE 802.3 Quick Primer Cabling Software Downloading _______ _______ _______ _______ _______ _______ Hub Management MIB Troubleshooting Reading the LEDs Telnet Communication ______ ______ ______ ______ ______ I found the following the most valuable ______________________________ _________________________________________________________________ _________________________________________________________________ I would like the following more developed ___________________________ _________________________________________________________________ _________________________________________________________________ I would find the manual more useful if _______________________________ _________________________________________________________________ _________________________________________________________________ Please fax or mail your feedback. Fax to 1-206-481-3790. Or mail to: Allied Telesyn Technical Publications Department 19015 North Creek Parkway, Suite 200 Bothell, WA 98011 USA 25