Download User manual

INTENSE 9P10 RGBWA
LED SLIM PANEL
Order code: LEDJ254
User manual
LEDJ Intense 9P10 RGBWA LED Slim Panel
Safety
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOUR INITIAL START-UP!
CAUTION!
Keep this equipment away from rain,
moisture and liquids.
SAFETY INSTRUCTIONS
Every person involved with the installation, operation & maintenance of this
equipment should:
-
Be competent
-
Follow the instructions of this manual
CAUTION! TAKE CARE USING THIS EQUIPMENT!
HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!
Before your initial start-up, please make sure that there is no damage caused during
transportation. Should there be any, consult your dealer and do not use the
equipment.
To maintain the equipment in good working condition and to ensure safe operation, it is necessary
for the user to follow the safety instructions and warning notes written in this manual.
Please note that damages caused by user modifications to this equipment are not
subject to warranty.
LEDJ Intense 9P10 RGBWA LED Slim Panel
Safety
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused
by the non-observance of this manual or any unauthorised modification to the
equipment.
• Never let the power-cable come into contact with other cables. Handle the power-cable
and all mains voltage connections with particular caution!
• Never remove warning or informative labels from the equipment.
• Do not open the equipment and do not modify the equipment.
• Do not connect this equipment to a dimmer-pack.
• Do not switch the equipment on and off in short intervals, as this will reduce the
system’s life.
• Only use the equipment indoors.
• Do not expose to flammable sources, liquids or gases.
• Cleaning must be done at regular intervals.
• Before cleaning, wait until the unit has cooled.
• Use a vacuum or dry compressed air and a soft brush to remove the dust collected on the
external vents and accessible internal components.
• Clean the external surfaces with a mild solution of non-ammonia glass cleaner or
isopropyl alcohol and wipe with a soft, lint free cotton cloth or lense cleaning tissue.
• Always disconnect the power from the mains when equipment is not in use or before
cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the
power-cable.
• Make sure that the available voltage is between 100V/240V.
• Make sure that the power-cable is never crimped or damaged. Check the equipment and
the power-cable periodically.
• If the equipment is dropped or damaged, disconnect the mains power supply immediately.
Have a qualified engineer inspect the equipment before operating again.
• If the equipment has been exposed to drastic temperature fluctuation (e.g. after
transportation), do not switch it on immediately. The arising condensation might damage
the equipment. Leave the equipment switched off until it has reached room temperature.
• If your product fails to function correctly, discontinue use immediately. Pack the unit
securely (preferably in the original packing material), and return it to your Prolight dealer
for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be carried out by a qualified
technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.
• WARRANTY; One year from date of purchase.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual,
the product may suffer damage and the warranty becomes void.
Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,
LED failure etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and property.
LEDJ Intense 9P10 RGBWA LED Slim Panel
Technical specifications
You should find inside the LEDJ carton the following items:
1, Intense 9P10 RGBWA LED Slim Panel
Technical Specifications:
2, Instruction manual
3, Power cable
DMX Channels: 5, 7 or 9 selectable
9 x 10W quad-colour LEDs
Beam angle: 25 degrees
Static colour, colour change, colour fade, auto, sound active, master/slave and DMX modes
IEC power in sockets
3-Pin XLR in/out sockets
4 push button menu with LED display
Twin hanging / floor bracket
Convection cooled
Power Consumption: 110W
Power supply: 100-240V ~ 50/60Hz
Dimensions: 260 x 93 x 295mm
Weight: 2.6Kgs
Overview:
10
www.prolight.co.uk
INTENSE 19T3 RGB LED SLIM PANEL
Identification:
1. Hanging / floor bracket
2. Earth screw
3. LED display
4. Function buttons
5. DMX input socket
6. DMX output socket
7. IEC power in socket
8. IEC power out socket
9. Hanging bracket tightening knobs
10. Safety bond point
11. Clamp mounting point
11
Setup
Operating Instructions
The Intense 9P10 RGBWA is a DMX-512 controllable, full RGBWA colour mixing Par Can made
up of high efficiency 10W LED’s. There are five colour groups (red, green, blue, white and amber)
whose intensity can be controlled individually allowing the creation of an unlimited range
of colours.
The Intense 9P10 RGBWA will operate in Stand-alone, Master/Slave, Sound activated and
DMX-512 control modes.
LEDJ Intense 9P10 RGBWA LED Slim Panel
Operations
DMX mode:
To access the DMX mode, press the “MODE” button on the LED display to show “d001” on the
LED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to set the
desired DMX address setting from “d001 - d512”. Once you have selected the desired DMX
address setting, press the “ENTER” button to choose one of the 5, 7 or 9 DMX channel modes
use the “UP” and “DOWN” buttons and press the “ENTER” button to confirm the setting.
Static colour mode
To access the static colour mode, press the “MODE” button on the LED display to show “Colt” on
the LED display. To change the brightness of each colour please see below.
Red Adjustment
To adjust the brightness of the red LEDs, press the “MODE” button to show “r255” on the
display. Now press use the “UP” and “DOWN” buttons to adjust the brightness from 000-255.
To confirm your choice, press the “ENTER” button. Note: 000 = off, 255 = full on.
Green Adjustment
To adjust the brightness of the green LEDs, press the “MODE” button to show “9255” on the
display. Now press use the “UP” and “DOWN” buttons to adjust the brightness from 000-255.
To confirm your choice, press the “ENTER” button. Note: 000 = off, 255 = full on.
Blue Adjustment
To adjust the brightness of the blue LEDs, press the “MODE” button to show “b255” on the
display. Now press use the “UP” and “DOWN” buttons to adjust the brightness from 000-255.
To confirm your choice, press the “ENTER” button. Note: 000 = off, 255 = full on.
White Adjustment
To adjust the brightness of the green LEDs, press the “MODE” button to show “u255” on the
display. Now press use the “UP” and “DOWN” buttons to adjust the brightness from 000-255.
To confirm your choice, press the “ENTER” button. Note: 000 = off, 255 = full on.
Amber Adjustment
To adjust the brightness of the blue LEDs, press the “MODE” button to show “A255” on the
display. Now press use the “UP” and “DOWN” buttons to adjust the brightness from 000-255.
To confirm your choice, press the “ENTER” button. Note: 000 = off, 255 = full on.
LEDJ Intense 9P10 RGBWA LED Slim Panel
Operations
Built-in programme mode
To access the static colour mode, press the “MODE” button on the LED display to show “Pr01”
on the LED display. Now use the “UP” and “DOWN” buttons to scroll the built in programmes from
Pr01 to Pr11.
To change the speed of the selected programme, press the “ENTER” button and use the “UP”
and “DOWN” buttons to set the speed from 00 to 99. To add strobe press the “ENTER” button
again and use the “UP” and “DOWN” buttons to set strobe from 00 to 99. To confirm your setting
press the “ENTER” button. Note: 00 = slow, 99 = fast.
In “Pr01” you can set a specific static colour. When in Pr01, press the “ENTER” button and use the
“UP” and “DOWN” buttons to scroll the through the list of built-in static colours.
1 = White (RGB)
7 = Spring Yellow
13 = Light Green
18 = Warm White
2 = Red
3 = Green 4 = Blue
8 = Yellow 9 = Purple 10 = Pink
14 = Light Blue
15 = Orange
19 = White (RGBWA)
5 = White (W) 11 = Cyan
16 = Lime
6 = Amber
12 = Light Pink
17 = Ultra Violet
To add strobe press the “ENTER” button again and use the “UP” and “DOWN” buttons to set
strobe from 00 to 99. To confirm your setting press the “ENTER” button.
Note: 00 = slow, 99 = fast
Auto run mode
To access the auto run mode, press the “MODE” button on the LED display to show “AUTO” on
the LED display. The unit will run through all of its built-in programmes.
Sound active mode
To access the sound active mode, press the “MODE” button on the LED display to show “Soud”
on the LED display. Now use the “UP” and “DOWN” buttons to set sound sensitivity level
from 00-31. Note: 00 = low, 99 = high.
Master/slave mode
To set the unit as the master, simply use any of the modes on this unit.
To set the unit as a slave unit(s), press the “MODE” button on the LED display to show “SLAv”
on the LED display. Now the unit will follow in sequence with the master unit.
LEDJ Intense 9P10 RGBWA LED Slim Panel
DMX Charts
5 channel DMX chart:
CHANNEL
VALUE
FUNCTION
1
0-255
Red 0-100%
2
0-255
Green 0-100%
3
0-255
Blue 0-100%
4
0-255
White 0-100%
5
0-255
Amber 0-100%
CHANNEL
VALUE
FUNCTION
1
0-255
Red 0-100%
2
0-255
Green 0-100%
3
0-255
Blue 0-100%
4
0-255
White 0-100%
5
0-255
Amber 0-100%
6
0-255
Master dimmer 0-100%
7
0-255
Strobe
7 channel DMX chart:
LEDJ Intense 9P10 RGBWA LED Slim Panel
9 channel DMX chart:
DMX Charts
LEDJ Intense 9P10 RGBWA LED Slim Panel
DMX Set up
DMX-512:
• DMX (Digital Multiplex) is a universal protocol used as a form of communication between
intelligent fixtures and controllers. A DMX controller sends DMX data instructions form the
controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the
DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have
a data “out” terminal).
DMX Linking:
• DMX is a language allowing all makes and models of different manufactures to be linked together
and operate from a single controller, as long as all fixtures and the controller are DMX compliant.
To ensure proper DMX data transmission, when using several DMX fixtures try to use the
shortest cable path possible. The order in which fixtures are connected in a DMX line does not
influence the DMX addressing. For example; a fixture assigned to a DMX address of 1 may be
placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a
fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to
address 1 to that unit, no matter where it is located in the DMX chain.
DATA Cable (DMX cable) requirements (for DMX operation):
• The LEDJ Intense 9P10 RGBWA can be controlled via DMX-512 protocol. The DMX address is
set on the back of the unit. Your unit and your DMX controller require a standard 3-pin XLR
connector for data input/output (figure 1).
Figure 1
Further DMX cables can be purchased
from all good sound and lighting suppliers
or Prolight dealers.
Please quote:
CABL10 – 2M
CABL11 – 5M
CABL12 – 10M
Also remember that DMX cable must be daisy chained and cannot be split.
LEDJ Intense 9P10 RGBWA LED Slim Panel
DMX Set up
DATA Cable (DMX cable) requirements (for DMX operation):
• The Intense Series can be controlled via DMX-512 protocol. The DMX address can be set on the
back of the fixture. Your fixture and your DMX controller require a standard 3-pin XLR
connector for data input/output (figure 1).
Figure 1
Also remember that DMX cable must be daisy chained and cannot be split.
Notice:
• Be sure to follow figures 2 & 3 when making your own cables. Do not connect the cable’s shield
conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer
casing. Grounding the shield could cause a short circuit and erratic behaviour.
Special Note: Line termination:
• When longer runs of cable are used, you may need to use a terminator on the last unit to
avoid erratic behaviour.
Termination reduces signal transmission problems
and interferance. it is always advisable to connect a
DMX terminal, (resistance 120 Ohm 1/4 W) between
pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.
Using a cable terminator (part number CABL90 3-pin, CABL89 5-pin) will decrease the
possibilities of erratic behaviour.
5-Pin XLR DMX Connectors:
• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin
XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin
XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the
correct cable conversion.
LEDJ Intense 9P10 RGBWA LED Slim Panel
Notes:
Notes