Download ReFreeX user manual for H422V9
Transcript
X e ree RF H422V9 User manual doc H422V9 Contents Contents 2 1 Parameter list 3 2 Parameter remarks 8 3 Alarm list 8 4 Slave alarm list 9 5 Button list 9 6 Led list 9 7 Soft command list 9 8 How to ... 10 9 Shortcut list 10 10 Led and push button location 10 The LATEX source of this document has been automatically produced by 4_13_22 on 2015-11-27 page 2\10 doc H422V9 1 Parameter list Rem. Parameter S__ St_ _t0 _tb _td _tH _tL _i0 _ib _id _iH _iL SA_ SAH SA0 SAd SAP SAh SAF SAo Fd_ 1 Fd0 Fdd Fdg 2 FdE FdF 3 FdP Fd1 Fd2 4 Fd3 FdY FF_ FFh FFd 5 FFo FP_ 6 FPt 7 FPF FPr FPH FPI Ft_ 8 Ftt FtF FtP M__ MU_ MLH MLL MLd MLU MHH MHL 9 MUO 10 MUU MUM MUL MUd MUb H__ HP_ HPP HPF HPd U__ UP_ 11 UPP UPH Description Minimum Functions about storage Functions about storage temperature storage room temperature -55.0 dead band 0.0 differential 0.0 maximum set point of temperature from slave keyboard -55.0 minimum set point of temperature from slave keyboard -55.0 storage room humidity 0.0 dead band 0.0 differential 0.0 maximum set point of humidity from slave keyboard 0.0 minimum set point of humidity from slave keyboard 0.0 Functions about air renew during storage enable air renew during storage oFF immediate delay before first air renew 0 on-time duration in the air renew cycle 0 period of air renew cycle 0 enable forced air renew by keyboard short cut oFF forced air renew duration 0 start / stop forced air renew oFF Functions about defrost duration and timing immediate delay before next defrost 0 on-time duration of the defrost 0 dripping time after defrost 0 maximum evaporator fan activation delay after the defrost 0 minimum evaporator fan activation delay after the defrost 0 overall period of the defrost 0 evaporator fan pulse duration (0.001 s units - select 0 for no pulse during defrost) 0 evaporator fan pulse period 0 defrost delay at power on 0 temperature display timeout after end of defrost - resets IA1=OS4=OS5 0 Functions about forced defrost enable forced defrost by keyboard short cut oFF forced defrost duration 0 start immediate forced defrost oFF Functions about defrost preference defrost type: 0=none / 1=pause / 2=air / 3=electric / 4=hot gas / 5=heat pump 0 / 6=heat pump by hp forced defrost type: 0=none / 1=pause / 2=air / 3=electric / 4=hot gas / 5=heat 0 pump / 6=heat pump by hp save defrost status into the real time clock oFF activate defrost output during defrost oFF activate defrost output during forced defrost oFF Functions about defrost temperature defrost stop temperature -55.0 forced defrost stop temperature -55.0 evaporator fan activation temperature after the defrost -55.0 Functions about compressor Functions about pressure switches low pressure safety restart ( similar to Danfoss KP15 lp set point ) 0.0 low pressure safety stop ( similar to Danfoss KP15 lp set point - differential ) 0.0 delay of low pressure safety stop 0 low pressure stop during pump down (intentional stop) 0.0 high pressure safety stop ( similar to Danfoss KP15 hp set point ) 0.0 high pressure safety restart ( similar to Danfoss KP15 hp set point - differential ) 0.0 minimum oil differential pressure 0.0 enable pump down oFF maximum pump down duration 0 low pressure forcing mc restart (repump down) 0.0 minimum delay for mc restarts (repump down) 0 do pump down before going to stand-by oFF Heating Heating preference heating method: 0=none / 1=electric / 2=hot gas / 3=heat pump / 4=intern heat 0 pump / 5=ihp2 heating source: 0=dedicated heating / 1=defrost / 2=light 0 heating delay 0 Dehumidification Dehumidification preference dehumidification type: 0=none / 1=force refr / 2=force heat / 3=alternate / 0 4=outer enable humidification oFF The LATEX source of this document has been automatically produced by 4_13_22 on 2015-11-27 Maximum Default Unit 2.0 0.0 0.2 45.0 -55.0 85.0 0.0 5.0 100.0 0.0 ◦C _on oFF 194 4:20:15 0 194 4:20:15 30:00 194 4:20:15 12:00:00 _on _on 194 4:20:15 30:00 _on oFF / dd dd dd / dd / 194 194 194 194 194 194 dd dd dd dd dd dd / dd dd dd 145.0 50.0 50.0 145.0 145.0 100.0 50.0 50.0 100.0 100.0 4:20:15 4:20:15 4:20:15 4:20:15 4:20:15 4:20:15 255 194 4:20:15 194 4:20:15 194 4:20:15 _on 194 4:20:15 _on 0 30:00 2:00 15:00 5:00 4:00:00 0 1:00 4:00:00 20:00 K K ◦C ◦C % % % % % hh:mm:ss hh:mm:ss hh:mm:ss hh:mm:ss hh:mm:ss hh:mm:ss hh:mm:ss hh:mm:ss hh:mm:ss hh:mm:ss hh:mm:ss hh:mm:ss hh:mm:ss _on / 30:00 dd hh:mm:ss oFF / 255 2 / 255 2 / _on _on _on oFF / _on / _on / 146.0 146.0 146.0 6.0 25.0 -20.0 ◦C 99.0 99.0 194 4:20:15 99.0 99.0 99.0 30.0 _on 194 4:20:15 99.0 194 4:20:15 _on 0.4 0.2 10 0.3 28.0 24.0 2.0 _on 1:00 1.0 15:00 oFF (gauge) bar (gauge) bar dd hh:mm:ss (gauge) bar (gauge) bar (gauge) bar (gauge) bar / dd hh:mm:ss (gauge) bar dd hh:mm:ss / 255 2 194 4:20:15 ◦C ◦C 0 / 0 / 3:00 dd hh:mm:ss 255 0 / _on oFF / page 3\10 doc H422V9 Rem. Parameter n__ nc_ ncH 12 ncr 13 ncU ncd n1H 14 n1L nE_ nEH nEM nE0 nEE nEt nEd c__ cP_ cPH cPF cPd cI_ cIH 15 cIo cId v__ vP_ 16 vPH vPP 17 vPd vPC vPS vP0 vt_ 18 vtt 19 vtH vtI 20 vtL vtF vtP vtU vtv vd_ 21 vd1 22 vd2 23 vdd vF_ 24 vFP vFd vFH vFt vb_ vbP vbd 25 vbH vbt b__ b1_ b1C b1A b2_ b2C b2A b3_ b3C b3A b4_ b4C b4A b5_ b5C b5A b6_ b6C b6A Description Minimum Functions about fans Functions about condenser fans enable condenser fans when compressor is off and discharge pressure is over maximum oFF enable condenser fans speed regulation oFF fan minimum speed 0 minimum HP-LP-difference to keep on fans 0.0 fan 1 start pressure ( similar to Danfoss KP5 set point ) - active just when ncr is oFF 0.0 fan 1 stop pressure ( similar to Danfoss KP5 set point - differential ) 0.0 Functions about evaporator fans force evaporator fans when refrigeration is off oFF force evaporator fans when humidification is on oFF enable evaporator fans when refrigeration is required but does not work oFF delay before establishing that refrigeration does not work 0 high defrost probe temperature forcing evaporator fan stop during cooling -55.0 differential 0.0 Functions about door and light Door switch and evaporator fan stop evaporator fans when door is open oFF pause defrost timer when air defrost is suspended by evaporator fan stop oFF delay of fan automatic switch on 0 Functions about light switch on the light when the door is open and off when closed oFF switch off the light automatically if it has been switched on from outside oFF delay of light automatic switch off 0 Functions about electronic expansion valve Functions about electronic expansion valve preference enable electronic expansion valve oFF refrigerant gas type: 0=R134A / 1=R404A / 2=R507A / 3=R22 / 4=R407C 0 network originating address of the pressure broadcast 0 the room is served by a central refrigerating unit oFF synchronize the liquid solenoid start with the central unit oFF delay before establishing that not enough info is received from the central unit 0 Functions about electronic expansion valve temperature wanted overheating (similar to Danfoss thermostatic overheating spring regulation) 0.0 maximum overheating 0.0 maximum low pressure (LP) to activate vtH parameter (maximum overheating) 0.0 minimum overheating 0.0 minimum overheating during hot gas defrost or heating 0.0 wanted overheating increase when evaporator fans are off during cooling 0.0 maximum pressure allowed in the suction line (similar to Danfoss MOP) 0.0 minimum high pressure (HP) to activate vtU parameter (MOP) 0.0 Functions about electronic expansion valve timing on-off duty cycle duration 0 on duty cycle duration at refrigeration start (set to 0 for previous stop value) 0 on duty cycle adaptation speed (low value for slow adaptation and small swinging) 0 Functions about turbo mode (forcing-on the expansion valve) turbo mode: 0=off / 1=on / 2=auto 0 turbo mode delay 0 suction pipe overheating for turbo mode activation 0.0 difference between room and set point required for turbo mode 0.0 Functions about cooling capacity boost (raising a flag for the central unit) boost mode: 0=off / 1=on / 2=auto 0 boost mode delay 0 room descent ramp, per hour, under which boost mode is activated 0.0 difference between room and set point required for boost mode 0.0 Functions about probe calibration Probe nr. 1 room temperature -99.0 enable probe oFF Probe nr. 2 defrost temperature -99.0 enable probe oFF Probe nr. 3 suction temperature -99.0 enable probe oFF Probe nr. 4 engine room temperature -99.0 enable probe oFF Probe nr. 5 humidity -99.0 enable probe oFF Probe nr. 6 high pressure (HP) -99.0 enable probe oFF The LATEX source of this document has been automatically produced by 4_13_22 on 2015-11-27 Maximum Default Unit _on _on 255 99.0 99.0 99.0 _on _on 40 2.0 10.0 6.0 / / / (gauge) bar (gauge) bar (gauge) bar _on _on _on 194 4:20:15 146.0 99.0 oFF oFF oFF 30:00 25.0 5.0 / / / dd hh:mm:ss ◦C K _on _on 194 4:20:15 _on / _on / 30:00 dd hh:mm:ss _on _on 194 4:20:15 _on / _on / 30 dd hh:mm:ss _on 255 255 _on _on 194 4:20:15 _on 0 0 oFF oFF 5:00 / / / / / dd hh:mm:ss 99.0 99.0 99.0 99.0 99.0 99.0 30.0 99.0 8.0 99.0 0.1 6.0 12.0 16.0 10.0 24.0 K K (gauge) bar K K K (gauge) bar (gauge) bar 194 4:20:15 194 4:20:15 255 8 dd hh:mm:ss 5 dd hh:mm:ss 8 / 255 194 4:20:15 99.0 99.0 2 30:00 12.0 1.0 / dd hh:mm:ss K K 255 194 4:20:15 99.0 99.0 2 1:00:00 0.5 2.0 / dd hh:mm:ss K K 99.0 _on 0.0 K _on / 99.0 _on 0.0 K _on / 99.0 _on 0.0 K _on / 99.0 _on 0.0 K _on / 99.0 _on 0.0 % oFF / 99.0 _on 0.0 bar _on / page 4\10 doc H422V9 Rem. Parameter b7_ b7C b7A b8_ b8C b8A b9_ b9C b9A L__ Lt_ LtE 26 LtL 27 LtH Ltd LF_ LFE LFL LFH LFd Li_ LiE LiL LiH Lid Lj_ LjE LjL LjH Ljd Ld_ LdE Ldo Ldd LE_ LEE LES LEo LEd LEF LM_ LME LMt LMd Ln_ LnE LnS Lnt Lnd LnF LO_ LOH LOd LOt LI_ L1H L1d L2H L2d L3H L3d L5H L5d Lo_ 28 Loo d__ dP_ 29 dP4 dF_ dF4 P__ Pd_ PdM PdS Description Probe nr. 7 low pressure (LP) enable probe Probe nr. 8 discharge temperature enable probe Probe nr. 9 oil pressure - eventually connected to AN-5 enable probe Functions about alarm and stand-by Temperature alarm alarm enable low temperature alarm set point high temperature alarm set point alarm delay Full stop temperature alarm alarm enable low temperature alarm set point high temperature alarm set point alarm delay Humidity alarm alarm enable low humidity alarm set point high humidity alarm set point alarm delay Full stop humidity alarm alarm enable low humidity alarm set point high humidity alarm set point alarm delay Low discharge overheating alarm alarm enable refrigerant overheating at the compressor outlet alarm delay Stop for low discharge overheating alarm alarm enable alarm show refrigerant overheating at the compressor outlet alarm delay alarm reset delay High discharge temperature alarm alarm enable high temperature alarm set point alarm delay Stop for high discharge temperature alarm alarm enable alarm show high temperature alarm set point alarm delay alarm reset delay Door alarm enable door alarm door alarm delay temperature alarm minimum delay after door opening Other alarm inputs enable digital input 1 alarm (compressor safety devices) digital input 1 alarm delay enable digital input 2 alarm (evaporator safety) digital input 2 alarm delay enable digital input 3 alarm (heating safety thermostat) digital input 3 alarm delay enable digital input 5 alarm (compressor phase monitor / thermal overload relay) digital input 5 alarm delay On / stand-by status actual status: stand-by or on Functions about delays Delay at power on delay at power on for relay nr. 4 - compressor Delay from previous stop delay from stop to activation of relay nr. 4 - compressor Functions about master preferences Functions about network address master address for global network communication number of slaves connected to this master The LATEX source of this document has been automatically produced by 4_13_22 on 2015-11-27 Minimum Maximum Default Unit -99.0 oFF 99.0 _on 0.0 bar _on / -99.0 oFF 99.0 _on 0.0 K _on / -99.0 oFF 99.0 _on 0.0 bar oFF / oFF -55.0 -55.0 0 _on 145.0 145.0 194 4:20:15 _on / -2.0 ◦ C 14.0 ◦ C 30:00 dd hh:mm:ss oFF -55.0 -55.0 0 _on 145.0 145.0 194 4:20:15 _on / -5.0 ◦ C 20.0 ◦ C 30:00 dd hh:mm:ss oFF 0.0 0.0 0 _on 100.0 100.0 194 4:20:15 oFF 0.0 100.0 30:00 / % % dd hh:mm:ss oFF 0.0 0.0 0 _on 100.0 100.0 194 4:20:15 oFF 0.0 100.0 30:00 / % % dd hh:mm:ss oFF -99.0 0 _on 99.0 194 4:20:15 oFF oFF -99.0 0 0 _on _on 99.0 194 4:20:15 194 4:20:15 _on oFF 12.0 10:00 5:00 oFF -55.0 0 _on 146.0 194 4:20:15 oFF / 105.0 ◦ C 1:00 dd hh:mm:ss oFF oFF -55.0 0 0 _on _on 146.0 194 4:20:15 194 4:20:15 _on oFF 110.0 1:00 5:00 oFF 0 0 _on 194 4:20:15 194 4:20:15 _on / 30:00 dd hh:mm:ss 15:00 dd hh:mm:ss oFF 0 oFF 0 oFF 0 oFF 0 _on 194 4:20:15 _on 194 4:20:15 _on 194 4:20:15 _on 194 4:20:15 _on 30:00 _on 30:00 _on 30:00 _on 1 oFF _on 0 194 4:20:15 15:00 dd hh:mm:ss 0 194 4:20:15 5:00 dd hh:mm:ss 0 1 254 2 oFF / 16.0 K 5:00 dd hh:mm:ss / / K dd hh:mm:ss dd hh:mm:ss / / ◦C dd hh:mm:ss dd hh:mm:ss / dd / dd / dd / dd hh:mm:ss hh:mm:ss hh:mm:ss hh:mm:ss oFF / 1 / 2 / page 5\10 doc H422V9 Rem. Parameter Description Minimum Maximum PO_ Output assignment PO2 assign out-2 relay to: 0=alarm / 1=heating / 2=humidifier / 3=air renew / 4=de0 255 frost duty / 5=humidity to FAN output / 6=outer dehumidifier / 7=OUT-1 / 8=OUT-3 / 9=OUT-4 / 10=OUT-5 / 11=OUT-6 / 12=FAN / 13=alarm NO / 14=fan off dehum I__ Functions about input-output and machine state (read only) IA_ Analog inputs IA1 room temperature -55.0 145.0 IA2 defrost temperature -55.0 145.0 IA3 suction temperature -55.0 145.0 IA4 engine room temperature -55.0 145.0 IA5 humidity 0.0 100.0 IA6 high pressure (HP) 0.0 30.0 IA7 low pressure (LP) 0.0 30.0 IA8 discharge temperature -55.0 145.0 IA9 oil pressure - eventually connected to AN-5 0.0 30.0 Id_ Digital input Id1 compressor hardware safety oFF _on Id2 evaporator hardware safety oFF _on Id3 defrost hardware safety oFF _on Id4 door closed oFF _on Id5 phase software safety oFF _on OA_ Analog output OA1 condenser 0 255 OA2 humidity - 4...20 mA 0 255 Od_ Digital output 30 Od1 solenoid oFF _on Od2 heating oFF _on Od3 light oFF _on Od4 compressor oFF _on Od5 evaporator oFF _on Od6 defrost oFF _on Od7 alarm - eventually connected to OUT-2 oFF _on Od8 steam producer - eventually connected OUT-2 oFF _on Od9 air renew - eventually connected to OUT-2 oFF _on Od0 digital output 2 oFF _on OS_ Machine status OS0 actual set point -55.0 145.0 OS1 low pressure (LP) 0.0 999.0 OS2 refrigerant saturation temperature corresponding to the low pressure -55.0 145.0 OS3 refrigerant overheating at the compressor inlet -999.0 999.0 OS4 temperature before defrost - reads IA1 at range reentering after defrost -55.0 145.0 OS5 set point temperature during defrost - reads IA1 at range reentering after defrost -55.0 145.0 25 OS6 room descent ramp, per hour -999.0 999.0 OS7 refrigerant saturation temperature corresponding to the high pressure -55.0 145.0 OS8 refrigerant overheating at the compressor outlet -999.0 999.0 OSS defrost status: 1=normal / 2=defr / 3=drip / 4=fan delay / 5=forced / 6=wait 0 255 LLA actual alarm - read only (0 means no alarm) 0 255 OSF defrost timer (in countdown-mode) 0 194 4:20:15 OSY timer of the temperature display timeout, after the end of defrost (see FdY) 0 194 4:20:15 Ov0 timer for not enough info (in countdown-mode) 0 194 4:20:15 OCH compressor hour counter 0 1193046:28:15 OSb special defrost display in progress - affects OS4 and OS5 (see FdY) oFF _on ObY instrument not in stand-by (instrument on) oFF _on OSt the instrument reached the set temperature oFF _on OSn evaporator fan stopped by door opening or manual control oFF _on Ont evaporator fan stopped by defrost temperature oFF _on OSH compressor stopped by high pressure oFF _on OSL compressor stopped by low pressure oFF _on OSd compressor stopped by low discharge overheating oFF _on OSE compressor stopped by high discharge temperature oFF _on OSU compressor running for pump down oFF _on MOP MOP limitation intervened recently oFF _on OUP dehumidification in progress oFF _on OPC the room is served by a central refrigerating unit oFF _on Ov1 not enough info is received from the central unit oFF _on On0 refrigeration is required but not working oFF _on Onv liquid refrigerant required from the central unit oFF _on OnH hot gas required from the central unit oFF _on OnF turbo mode oFF _on Onb boost mode oFF _on E__ Functions about slave preferences Ed_ Functions about network address EdS slave address for local network communication 1 254 The LATEX source of this document has been automatically produced by 4_13_22 on 2015-11-27 Default Unit 0 / -55.0 -55.0 -55.0 -55.0 0.0 0.0 0.0 -55.0 0.0 oFF oFF oFF oFF oFF ◦C ◦C ◦C ◦C % (gauge) bar (gauge) bar ◦C (gauge) bar / / / / / 0 / 0 / oFF oFF oFF oFF oFF oFF oFF oFF oFF oFF -55.0 0.0 -55.0 -999.0 -55.0 -55.0 -999.0 -55.0 -999.0 0 0 0 0 0 0 oFF oFF oFF oFF oFF oFF oFF oFF oFF oFF oFF oFF oFF oFF oFF oFF oFF oFF oFF / / / / / / / / / / ◦C (gauge) bar ◦C K ◦C ◦C K ◦C K / / dd hh:mm:ss dd hh:mm:ss dd hh:mm:ss h...h:mm:ss / / / / / / / / / / / / / / / / / / / 1 / page 6\10 doc H422V9 Rem. Parameter EY_ EYY EYr E0_ E0d E0E E1_ E1d E1t E1E E2_ E2d E2t E2E E3_ E3d E3t E3E E4_ E4d E4t E4E E5_ E5d E5t E5E E6_ E6d E6t E6E E7_ E7d E7t E7E E8_ E8d E8t E8E E9_ E9d E9t E9E F0_ F0d F0t F0E F1_ F1d F1t F1E F2_ F2d F2t F2E F3_ F3d F3t F3E F4_ F4d F4t F4E F5_ F5d F5t F5E F6_ F6d F6t F6E F7_ F7d F7t F7E Description Functions about display input to show on display: 1=IA1 / 2=IA2 ... enable display rotation: 0=off / 1=all / 2=selected Functions about display rotation, when EYr=1 duration of label display during rotation duration of value display during rotation Functions about display rotation, when EYr=2 (repeated duration of label display during rotation label text during rotation duration of value display during rotation Functions about display rotation, when EYr=2 (repeated duration of label display during rotation label text during rotation duration of value display during rotation Functions about display rotation, when EYr=2 (repeated duration of label display during rotation label text during rotation duration of value display during rotation Functions about display rotation, when EYr=2 (repeated duration of label display during rotation label text during rotation duration of value display during rotation Functions about display rotation, when EYr=2 (repeated duration of label display during rotation label text during rotation duration of value display during rotation Functions about display rotation, when EYr=2 (repeated duration of label display during rotation label text during rotation duration of value display during rotation Functions about display rotation, when EYr=2 (repeated duration of label display during rotation label text during rotation duration of value display during rotation Functions about display rotation, when EYr=2 (repeated duration of label display during rotation label text during rotation duration of value display during rotation Functions about display rotation, when EYr=2 (repeated duration of label display during rotation label text during rotation duration of value display during rotation Functions about display rotation, when EYr=2 (repeated duration of label display during rotation label text during rotation duration of value display during rotation Functions about display rotation, when EYr=2 (repeated duration of label display during rotation label text during rotation duration of value display during rotation Functions about display rotation, when EYr=2 (repeated duration of label display during rotation label text during rotation duration of value display during rotation Functions about display rotation, when EYr=2 (repeated duration of label display during rotation label text during rotation duration of value display during rotation Functions about display rotation, when EYr=2 (repeated duration of label display during rotation label text during rotation duration of value display during rotation Functions about display rotation, when EYr=2 (repeated duration of label display during rotation label text during rotation duration of value display during rotation Functions about display rotation, when EYr=2 (repeated duration of label display during rotation label text during rotation duration of value display during rotation Functions about display rotation, when EYr=2 (repeated duration of label display during rotation label text during rotation duration of value display during rotation Minimum Maximum Default Unit 0 0 255 2 1 / 0 / 0 0 255 255 1 / 2 / 0 000 0 255 yyy 255 0 / rM= / 6 / 0 000 0 255 yyy 255 1 / dE= / 0 / 0 000 0 255 yyy 255 1 / SU= / 0 / 0 000 0 255 yyy 255 1 / Er= / 0 / 0 000 0 255 yyy 255 1 / rH= / 4 / 0 000 0 255 yyy 255 1 / HP= / 0 / 0 000 0 255 yyy 255 1 / LP= / 0 / 0 000 0 255 yyy 255 1 / dI= / 0 / 0 000 0 255 yyy 255 1 / oI= / 0 / 0 000 0 255 yyy 255 1 / _t= / 4 / 0 000 0 255 yyy 255 1 / LP= / 0 / 0 000 0 255 yyy 255 1 / Lt= / 0 / 0 000 0 255 yyy 255 1 / oh= / 0 / 0 000 0 255 yyy 255 1 / bF= / 0 / 0 000 0 255 yyy 255 1 / SF= / 0 / 0 000 0 255 yyy 255 1 / MP= / 0 / 0 000 0 255 yyy 255 1 / Ht= / 0 / for each parameter) for each parameter) for each parameter) for each parameter) for each parameter) for each parameter) for each parameter) for each parameter) for each parameter) for each parameter) for each parameter) for each parameter) for each parameter) for each parameter) for each parameter) for each parameter) for each parameter) The LATEX source of this document has been automatically produced by 4_13_22 on 2015-11-27 page 7\10 doc H422V9 Rem. Parameter F8_ F8d F8t F8E Eb_ EbH EF_ EFF EP_ 31 EPA 2 Nr. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 3 Description Functions about display rotation, when EYr=2 (repeated for each parameter) duration of label display during rotation label text during rotation duration of value display during rotation Functions about buzzer enable buzzer Functions about slave default reload slave default parameters from EEPROM, at next restart Functions about slave password set a new password Minimum Maximum Default Unit 0 000 0 255 yyy 255 1 / od= / 0 / 0 1 1 / 0 1 0 / 000 yyy ___ / Parameter remarks Remark Defrost is not performed twice in case safety switches of mc or evaporator are not ok. The evaporator fans are restarted after FdF delay and before FdE delay, as soon as the defrost temperature reaches FtP. The period of each cycle includes on-time + off-time, that is the overall duration of the cycle. Eventually disabled by the parameter FPr. Following defrost cycles will be aligned to the end of forced one. Add 100 to FPt parameter to enable the outer defrost drive on INP-4. The defrost is initiated by INP-4 closure; after defrost and until INP-4 is closed, the instrument does not leave the dripping mode, to coordinate with eventual other instruments. In H422V9, starting from revision 09, when FPt or FPF is 6, Ftt and FtF set the HP dew temperature that stops heat pump defrost. In case of hot gas defrost, both IA2 and IA3 must reach Ftt. Fixed time 120 s and manual reset. When activated, a clever pump down algorithm coordinates the solenoid, the evaporator and the mc. There is no concurrent run of mc and electric defrost or heating. Forced refrigeration is disabled when room temperature is under LFL, forced heating is disabled over LFH. When speed regulation is off the fan is operated on-off. Caution! Speed regulation can cause fan fault or electronic board fault. Low and average minimum speed can increase the risk. During the first 10 seconds of speed regulation, the n1L is replaced by (n1H+n1L)/2. No action if the light is switched on from inside the room. When off, the refrigeration solenoid is steadily on during cooling, without any safety. Use turbo mode for better control. The address of the central unit who is broadcasting pressure (usually 1). Use 0 for previous application H425V1 with no origin specification. Caution! Low overheating causes liquid return and compressor damage. Overheating over the maximum forces valve anticipated opening. Overheating under the minimum delays valve opening. Caution! Short duty cycle reduces valve life. Caution! Low overheating causes liquid return and compressor damage. Caution! High adaptation speed causes swing in the suction line and damage to the compressor. In turbo mode, the liquid refrigerant solenoid opens over vtt overheating, and closes at vtL. Positive values mean temperature descent. The low temperature differential is fixed, and alarm status stops at 0.2 ◦ C above the set point. The high temperature differential is fixed, and alarm status stops at 0.2 ◦ C under the set point. Passing from stand-by to on and at power on, there is a 5 second delay spent in a virtual stand-by. In case a crankcase heater is installed, a long delay is advised. Press Esc to skip compressor delay. The minus sign on display ("-") signals that output is going to start after a delay. The use of this parameter is restricted to ReFreeX authorized personnel; further detail is available on demand. This parameter is not implemented on every instrument. The value and the action of this parameter are local to each slave. If you are unsure, during action relative to this parameter, press B1 at any moment. Three underscores, three zero digits, and three empty-characters are considered trivial password values; any other combination of three alphanumeric characters is a non-trivial password. If a non-trivial password value is set, then entering the menu, the label PAS is shown. Press B6, then introduce the password, confirm by B6, and press B4. If the introduced value does not match the saved password, then the label PAS is shown again, and the operation may be retried for a maximum of other two times. In case of unlocking failure, the label bAd is shown. To exit, press B4 twice or B1 once. To remove the password, set EPA to value 000 . To set or to change the password, if you know the authorization code, set EPA to a new non-trivial value, and exit the menu. The label rEP is shown. Press B6, then reintroduce the same password, confirm by B6, and press B4. The label AUt is shown. Press B6, then introduce the authorization code, confirm by B6, and press B4. Alarm list Display A01 A02 A03 A04 A05 A06 Alarm low temperature high temperature mc alarm evaporator alarm defrost alarm door open Low temperature limit has been reached. High temperature limit has been reached. Pressure switch, thermistors, or any other compressor safety device has disconnected. Evaporator thermal relay, or other evaporator safety device has disconnected. defrost safety thermostat, or any other defrost safety device has disconnected. Time limit for door opening has been reached. The LATEX source of this document has been automatically produced by 4_13_22 on 2015-11-27 page 8\10 doc H422V9 Display A07 A08 A09 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 4 Push B1 B2 B3 B4 B5 B6 6 Led L1 L2 L3 L4 L5 L6 L7 7 Compressor overload/thermal relay disconnected, or missing mains phase - manual reset. Low temperature limit for full stop has been reached - full system stop - manual reset. High temperature limit for full stop has been reached - full system stop - manual reset. Oil differential pressure remained under minimum value for 120 seconds - manual reset. Low humidity limit has been reached High humidity limit has been reached. Low humidity limit for full stop has been reached - full system stop - manual reset. High humidity limit for full stop has been reached - full system stop - manual reset. Memory loss of real time clock [RTC] - timer reset. EEPROM invalid. EEPROM read start failure EEPROM read end failure EEPROM write start failure. EEPROM write end failure. EEPROM failure - reached the maximum number of writing attempts. Refrigerant overheating at compressor outlet went under alarm threshold. Refrigerant overheating at compressor outlet went under alarm threshold - compressor stop - delayed reset. Refrigerant temperature at compressor outlet went over alarm threshold. Refrigerant temperature at compressor outlet went over alarm threshold - compressor stop - delayed reset. Slave alarm list Display A96 A97 A98 A99 5 Alarm mc phase low temp stop high temp stop oil pressure low humidity high humidity low humid stop high humid stop RTC memory loss EEPROM invalid EEPROM read start EEPROM read end EEPROM write start EEPROM write end EEPROM write max low discharge oh low disch oh stop high discharge t high disch stop Alarm slave EEPROM out of range no link lost link Failed write operation onto the slave EEPROM. The slave address EdS might be out of the master range, the latter going from 1 to PdS. The slave does not receive any message from the master. The slave lost the communication with the master. Button list button esc - silence - skip up on/stand-by - pause left - light down - defrost right - menu - set Function Exit without saving from any menu - alarm buzzer silence - skip compressor delay. Up navigation in the menu. Toggle between on and stand-by - toggle evaporator fan stop. Left navigation in the menu - switch the light on and off. Down navigation in the menu - force immediate defrost or skip the one in progress. Right navigation in the menu - display and modify the set point - enter menu. Led list compressor evaporator defrost-hum-deh air renew heating unused light Function On during compressor run - blinking slowly during activation delay and pumpdown. On during evaporator run - blinking slowly during activation delay and pumpdown. On during defrost and humidification - blinking slowly during dripping and dehumidification. On during air renew. On during heating. Unused in this application. On when lighting is on - blinking slowly during deactivation delay. Soft command list Soft command 4 skip mc delay 5 skip defrost 6 reset mc counter Function Skip compressor delay. Skip defrost in progress and enter fan pause. Reset compressor hour counter. The LATEX source of this document has been automatically produced by 4_13_22 on 2015-11-27 page 9\10 doc H422V9 How to ... How to ... Switch between on and stand-by. Stop or restart evaporator fans. Program the menu. Show or change temperature set. Force an air renew. Force or skip a defrost. 9 Shortcut list Buttons to press B5 B2 10 Function Keep pressed B3 button, to activate and deactivate stand-by. In stand-by every output is disabled except light, leds from L1 to L6 blink, timers continue to count. Press shortly the B3 button. When the evaporator fans are stopped, the display blinks. Keep pressed B6 to enter the menu. Navigate up and down with B2 and B5. Select the submenu by B6. Change the parameter by B2 and B5, press B6 to confirm, or B4 to go back without saving. The changes will have effect after the exit from programming pressing B4 repeatedly. Press B1 to exit immediately without saving any parameter. Press shortly B6 - the display shows the current set point - change it by B2 and B5, and confirm it by B6. As alternative, enter the menu program as explained above, modify the parameter _t0, then confirm it. Keep pressed B2. Keep pressed B5. Shortcut description - keep pressed 5 seconds Force an immediate defrost, or skip the one in progress. Force an immediate air renew. Led and push button location ReFreeX L1 L2 L3 L4 L5 L6 B1 B2 B3 B4 B5 B6 L7 Set doc A112X1 8 80% refrigerant reduction – full digital control – reduced winter consumption 80% di riduzione del refrigerante – controllo digitale completo – consumi invernali ridotti The LATEX source of this document has been automatically produced by 4_13_22 on 2015-11-27 page 10\10