1
Download User Manual - INTEC Controls
Transcript
PolyGard® Multi-Point Controller User Manual - MGC2-16 4.2 Page 25 Unit position – Connection diagram Green/Ye G Gray X Gray H Blue N Green/Ye G 120 VAC Input Power (see ill. 1) (see ill. 2) Binary - Relay Outputs R01 R02 R03 R04 R05 1 2 1 2 3 4 5 6 X1 Fault Binary - Relay Outputs R06 R07 R08 R09 R10 7 8 9 10 11 12 13 14 15 1 X2 X1 2 1 2 3 4 5 6 (see ill. 3) 7 8 9 10 11 12 13 14 15 X2 EP-02-1 Alarm INTEC Controls 05.07 .10 10: 28am (see ill. 2) DIN Rail X10 X11 X10 X11 1 2 3 4 5 6 7 8 9 101112 1 2 3 4 5 6 7 8 9 101112 1 2 3 4 5 6 7 8 9 101112 1 2 3 4 5 6 7 8 9 101112 Sensor Inputs (see ill. 4) Sensor Inputs Digital Analog Inputs Outputs Binary - Relay Outputs R11 R12 R13 R14 R15 2 1 2 3 4 5 6 X1 (see ill. 6) Binary - Relay Outputs R16 R17 R18 R19 R20 7 8 9 10 11 12 13 14 15 1 X2 X1 EP-02-2 Analog Outputs Optional: Modbus Interface (see ill. 2) (see ill. 8) (see ill. 2) (see ill. 5) (see ill. 6) 1 (see ill. 4) 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 X2 EP-02-3 DIN Rail (see ill. 4) X10 X11 X10 X11 1 2 3 4 5 6 7 8 9 101112 1 2 3 4 5 6 7 8 9 101112 1 2 3 4 5 6 7 8 9 101112 1 2 3 4 5 6 7 8 9 101112 Sensor Inputs Sensor Inputs Analog Outputs 1 2 3 4 5 6 7 8 X2 Analog Outputs C5 Comm. Coupler (see ill. 3) (see ill. 6) Terminal 1 block “X1” 2 (see ill. 4) Optional: BACnet (see ill. 6) 24 VDC Output X1 Circuit breaker 1F1 1 2 3 4 Power Unit L N G VV+ (+)(-)(A)(B) Top Bottom Horn (see ill. 7) 120 VAC Input Power Supply H N G Gray Blue Green/Yellow AC hot AC neutral Earth ground Terminal block 120 VAC (90...230 VAC), 50/60 Hz • “Min wire size 16 AWG (1.5 mm2)” • Resettable breaker, max 10 A, rated current approx. 2 A ill. 1 Polygard® is a registered trademark of MSR Customer Services (858) 578-7887 & (888) GO INTEC Fax (858) 578-4633 & (888) FX INTEC www.inteccontrols.com INTEC Controls, 12700 Stowe Dr., Suite 100, Poway, CA 92064 MGC2-16 Specification subject to change without notice. Printed in USA 131119
