Download Untitled
Transcript
www. mequi m. c om. pe S. A T el : 2265050-2268888, Emai l mequi m@mequi m. c om. pe SUEL OS CEMENTO ASF AL TOS CONCRETO Soil Equipment Soil Classification Soil is one of the oldest forming structures that our planet is formed from. Soil is a loose rocky material that is vastly used in the construction industry. Hence it is very important to test the ground soil before construction and to know the type and classification of the soil before any project. The type of soil can be identified by several parameters one of which the percentage of clay, silt or sand found in its composition. This classification will determine the characteristics of the soil used in the civil engineering project. 02 Other physical parameters such as moisture content, shear strength, elasticity, specific gravity, density, degree of compaction, penetration resistance, consistency, bearing capacity, hydraulic conductivity, permeability and consolidation can effect the soil characteristics and behaviour during construction. The principle of soil mechanics requires the use of standard testing methods offered by our range of equipment and used by trained and qualified engineers and technicians. The testing equipment described in this section are carefully designed and manufactured to the highest international standard necessary to achieve accurate and repeatable results in testing soil material. 03 Geotechnical Testing Equipment Soil Colour Chart The Soil Colour Chart is used to judge the color of rocks, archaeological specimens and soil samples. 322 color chips are permanently mounted on 9 charts for basic collection of 7 hues (10R-5Y) and 2 grey charts with apertures between chips to make comparisons easier. The tropical soil colour chart Set of 2, for use with reddish tropical soils and recommended for tropical regions. Soil Equipment Water Level Indicators Washable new edition features handy tabs for flipping to needed charts without getting pages dirty. SL 0101 Soil Colour Chart SL 0102 Tropical Soil Colour Chart The Water Level Indicators are used to determine the water level in boreholes and wells. Drum mounted, with an ON/OFF switch indicator and audio signal when probe touches the water. The cable is marked at intervals and is battery operated. SL 0116 Water Level Indicators 50 meters SL 0117 Water Level Indicators 100 meters SL 0118 Water Level Indicators 150 meters SL 0119 Water Level Indicators 200 meters Proctor Penetrometer (spring type) Soil Sampling Kit Standards: ASTM D1558 The Soil Sampling Kit is designed to obtain samples for soil investigation and exploration purposes. Made of special galvanised steel the set provide all the items needed in a convenient carrying case. The complete kit is based on the most popular sizes used for undisturbed soil sampling including cleaning brush and user manual. SL 0103 Soil Sampling kit SL 0104 Soil Prospecting kit SL 0105 Hand Auger Head 80 mm dia SL 0106 Hand Auger Head 100 mm dia SL 0107 Hand Auger Head 150 mm dia SL 0108 Extended rod 1 m long Power Auger Head The Power Auger Head has an Ergonomic designed for optimum comfort. It comes with a 4.5 KW two stroke engine, equipped with a lever preventing accidental acceleration and a Quick-fit spigot-socket coupler for swift attachment and replacement of bits. SL 0109 Power Auger Head 04 Accessories: SL 0110 Auger 60 mm dia x 1 m long SL 0111 Auger 80 mm dia x 1 m long SL 0112 Auger 100 mm dia x 1 m long SL 0113 Auger 150 mm dia x 1 m long SL 0114 Auger 200 mm dia x 1 m long SL 0115 Extension rod The Proctor Penetrometer is used for determining the penetration resistance of fine-grained soils. The unit consists of a special calibrated spring dynamometer with a pressure-indicating scale on the stem of the handle. It comes with a stainless steel adaptor stem for larger needles. The pressure scale is calibrated to 100 lbs. by 1 lb. subdivisions. There is a major division located at each 10 lb. interval. A sliding ring on the stem indicates the maximum load obtained during the test. SL 0120 Proctor Penetrometer complete set with needle point SL 0121 Set of spare needle point (0.25, 0.5, 1, 1.5, 2, 3, 5, 6 cm²) Proving Ring Penetrometer The Proving Ring Penetrometer is used to determine the bearing strength, compacting degree of subgrades and also penetration resistance of soil. SL 0122 Proving ring Penetrometer complete It comes with a T handle 1 KN load ring, Maximum load pointer and calibration chart. www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 05 Geotechnical Testing Equipment Dial Penetrometer Pocket Penetrometer The Pocket Penetrometer is used in field exploration and in checking and comparing similar types of soil. Classifying cohesive soils in terms of consistency and estimation of approximate unconfined compressive strength and shear strength. Soil Equipment The cylindrical tip of 0.31 cm² area penetrate into the soil up to 6 mm marked point. A cursor on the scale reads directly unconfined compressive strength in kgf/cm². The Dial Penetrometer comes in three different versions, the dial has a maximum value holding system with 0 setting by push buttom. The Dial dia is 60 mm, with peak holding features. SL 0123 Pocket Penetrometer SL 0126 Range 0 to 5 kgf/cm2, plungers dia is 6.35 mm SL 0127 Range 3 to 15 kgf/cm2, plungers dia is 6.35 mm SL 0128 Range 0 to 6 kgf/cm2, plungers dia is 6.35 mm - 10 - 15 - 20 - 25 Pocket Shear Vane Dynamic Cone Penetrometer Standards: BS 1377, 1924, 812, EN 932-1 The Dynamic Cone Penetrometer is used for In-rapid in situ measurement of structural properties of existing road pavement constructed with unbound materials. It consists of an 8 kg weight dropping through a height of 575 mm and 60° cone having a diameter of 20 mm. DCP measurements can be made down to a depth of approximately 850 mm. Sensitive Vane adaptor, range 0 to 2 N/cm2 High capacity vane adaptor range 0 to 25 N/cm2 SL 0129 Pocket Vane Complete set Field Inspection Vane Tester Standards: ASTM D2573 SL 0124 Dynamic Cone Penetrometer set Static Cone Penetrometer The Static Cone Penetrometer is used to evaluate the consistency of soils, their level of compaction and the bearing capacity of shallow foundations and pavement subgrades. 70 kg/cm² reads cone resistance directly, eliminating need for proving ring conversions. Stainless steel and anodized aluminium construction for reliable performance. Specifically developed for use in fine grained soils, particularly soft soils, to depths of 30 feet. They use a 60° cone with an area of 1.5 cm². An optional cone with a 3 cm² area is available for use in very soft soils. Dual rod construction isolates cone resistance from shaft friction Pressure gauge ranging from 0 to Standard models include: A 60° cone with a maximum area of 1.5 cm² A Starter Rod Assembly designed to withstand an axial force of 250 lbf (340 N•m) maximum Pressure gauge marked in kg/cm² Operating Instructions and parts list SL 0125 Static Cone Penetrometer 06 The Pocket Shear Vane can be used in the laboratory, at the end of sample tubes, etc Supplied complete with: Standard 25 mm dia, vane range 0 to 10 N/cm2 The Field Inspection Vane Tester can be used to determine the maximum shearing force that can be exercised on a soil. Measurement in the field (on the surface, in profile pits or at the bottom of bore holes) as well as in the laboratory (on samples) are possible. The shear stress measured can be read on a clearly readable scale ring. In soft soils it is not necessary to make a bore hole first. In order to determine the friction on the extension rods a dummy vane is available in these situations. SL 0130 Field Inspection Vane complete set Laboratory Vane Apparatus The Laboratory Vane Apparatus is used to determine the shear strength in soft soil of undisturbed remolded samples. Both manual and motorised versions are available Lightweight, compact, portable and self contained. SL 0131 Manual Laboratory Vane Apparatus SL 0132 Motorised Laboratory Vane Apparatus SL 0133 Vane 12.7 mm x 12.7 mm SL 0134 Vane 12.7 mm x 19 mm SL 0135 Vane 12.7 mm x 25.4 mm SL 0136 Attachment to hold a sample tube of 38 mm or 100 mm dia www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 07 Geotechnical Testing Equipment Laboratory Mixer Soil Equipment Laboratory Soil Grinder Standards: BS 598-107, 1377-1, 1924-1, EN 12697-35 The Laboratory mixer is a planetary beater type, where the flat beaters rotate in the opposite direction to the orbit around the inside of the mixing bowl. This ensures that the mixing is thorough and uniform. It has a direct gear drive transmission that may be set for three speeds with a control lever. The hand lever can raise, lower and lock the bowl at the desired position. Adjustment is allowed for proper clearance between the bowl and the beater. This Mixer is suitable for sample preparation of soils, bituminous concrete and cement mortars. SL 0137 Laboratory Mixer 5 litre capacity complete with all accessories SL 0138 Laboratory Mixer 10 litre capacity complete with all accessories SL 0139 Spare stainless steel Bowl SL 0140 Spare stainless steel Beater It is fitted with an electronic temperature regulator and can be easily fitted to the mixer under the bowl. Max. temperature 180 °C The Soil Grinder is used in place of a soil mortar and pestle to quickly reduce cakes of dry soil for particlesize analysis. It is intended to grind the fraction retained on a designated sieve until the aggregations of soil particles are broken up into separate grains. Melting Pot Isomantle Heater The Isomantle Heater is Used to heat the mixing bowl of (5 litres cap.) and (10 litres cap.) mixer. The Soil Grinder Prepares soil samples to designated particle size for accurate, repeatable test results. Grinds one-pint sample in 15 seconds. Stainless steel construction. Includes a No. 10 perforated stainless plate. SL 0141 Isomantle Heater 5 litres cap SL 0142 Isomantle Heater 10 Litres cap. Porcelain Mortar and Rubber Head Pestle The Melting pot is used to melt wax, or asphalt material used to seal the soil samples and other materials. The temperature is adjustable and maintained at the desired value through the thermostat controler. Supplier complete with aluminum cover. Made from cast aluminum material with a heat resistant knob. Continuous grinding is ensured by using the gate below the hopper to feed the soil at a rate that does not stall the motor. SL 0146 Laboratory Soil Grinder Specify Temp: - 60° to 250°C, 100° to 320°C - 60° to 450°C, 150° to 550°C SL 0147 Melting Pot 1/2 litre SL 0148 Melting Pot 1 litre SL 0149 Melting Pot 2.5 litre SL 0150 Melting Pot 4.5 litre SL 0151 Melting Pot 9 litres Sieve Shaker Standards: EN 932-5, ISO 3310-1 The Porcelain Mortar and Rubber Head Pestle is used for sample reduction by gently crushing individual particles. SL 0143 Porcelain Mortar and Rubber Head Pestle complete set SL 0144 Spare Porcelain Mortar 125 mm dia SL 0145 Spare Rubber Head Pestle 08 The Sieve Shaker imparts a circular motion to the material being sieved so that it makes a slow progression over the surface of the sieve. At the same time a feature of the rapid vertical movement agitates the sample which helps to clear the sieve apertures and avoid them blinding. The shaker is fitted with timer which can be pre-set for any duration up to 60 minutes. This unit will accept 200mm and 300mm diameter sieves. Wet sieving kits in the appropriate sizes may be used with this shaker. SL 0152 Sieve Shaker www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 09 Geotechnical Testing Equipment Electromagnetic Sieve Shaker Soil Equipment Testing Sieves Standards: EN 933-2, ISO 3310-1, ISO 3310-2, ISO 565 The Sieve Shaker is powered by an electromagnetic drive which has no rotating parts to wear making it maintenance free and extremely quiet in operation. The digital controller is used to set both the process time and amplitude setting while a further control enables the vibration to run continuously or intermittently. The vibratory action produced by the power unit moves the sample over the sieve in a unique way producing faster more efficient sieving, while the rapid vertical movements also help keep the apertures from pegging. SL 0153 Electromagnetic Sieve Shaker Testing Sieves Standards: EN 933-2, ISO 3310-1, ISO 3310-2, ISO 565 All test sieves are manufactured to National and International Specifications and are supplied with a “Certificate of Compliance”. Each sieve is individually serial numbered, ensuring full traceability. Particle Size Analysis is probably performed in all laboratories engaged in testing materials for civil engineering applications. The range of sieves offered includes ISO, EN, BS and ASTM sieves. Woven wire test sieves are manufactured from stainless steel mesh while the Perforated plate test sieves are manufactured from tinned steel plate. All test sieves unless otherwise indicated are supplied with full-depth frames. All our sieves are manufactured in the United Kingdom. 10 Sieve Size 200 mm dia Product code SL 0155 SL 0156 SL 0157 SL 0158 SL 0159 SL 0160 SL 0161 SL 0162 SL 0163 SL 0164 SL 0165 SL 0166 SL 0167 SL 0168 SL 0169 SL 0170 SL 0171 SL 0172 SL 0173 SL 0174 SL 0175 SL 0176 SL 0177 SL 0178 SL 0179 SL 0180 SL 0181 SL 0182 SL 0183 SL 0184 SL 0185 SL 0186 SL 0187 SL 0188 SL 0189 SL 0190 SL 0191 Sieve Size 300 mm dia Product code SL 0192 SL 0193 SL 0194 SL 0195 SL 0196 SL 0197 SL 0198 SL 0199 SL 0200 SL 0201 SL 0202 SL 0203 SL 0204 SL 0205 SL 0206 SL 0207 SL 0208 SL 0209 SL 0210 SL 0211 SL 0212 SL 0213 SL 0214 SL 0215 SL 0216 SL 0217 SL 0218 SL 0219 SL 0220 SL 0221 SL 0222 SL 0223 SL 0224 SL 0225 SL 0226 SL 0227 SL 0228 www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 Woven wire stainless steel mesh Mesh Size and description, BS 410/ISO 3310 Lid Receiver 20 micron 25 micron 32 micron 36 micron 38 micron 40 micron 45 micron 50 micron 53 micron 56 micron 63 micron 71 micron 75 micron 80 micron 90 micron 100 micron 106 micron 112 micron 125 micron 140 micron 150 micron 160 micron 180 micron 200 micron 212 micron 224 micron 250 micron 280 micron 300 micron 315 micron 355 micron 400 micron 425 micron 450 micron 500 micron 11 Geotechnical Testing Equipment Soil Equipment Testing Sieves Testing Sieves Standards: EN 933-2, ISO 3310-1, ISO 3310-2, ISO 565 Sieve Size 200 mm dia Product code SL 0229 SL 0230 SL 0231 SL 0232 SL 0233 SL 0234 SL 0235 SL 0236 SL 0237 SL 0238 SL 0239 SL 0240 SL 0241 SL 0242 SL 0243 SL 0244 SL 0245 SL 0246 SL 0247 SL 0248 SL 0249 SL 0250 SL 0251 SL 0252 SL 0253 SL 0254 SL 0255 SL 0256 SL 0257 SL 0258 SL 0259 SL 0260 SL 0261 SL 0262 SL 0263 SL 0264 SL 0265 12 Sieve Size 300 mm dia Product code SL 0266 SL 0267 SL 0268 SL 0269 SL 0270 SL 0271 SL 0272 SL 0273 SL 0274 SL 0275 SL 0276 SL 0277 SL 0278 SL 0279 SL 0280 SL 0281 SL 0282 SL 0283 SL 0284 SL 0285 SL 0286 SL 0287 SL 0288 SL 0289 SL 0290 SL 0291 SL 0292 SL 0293 SL 0294 SL 0295 SL 0296 SL 0297 SL 0298 SL 0299 SL 0300 SL 0301 SL 0302 Standards: EN 933-2, ISO 3310-1, ISO 3310-2, ISO 565 Woven wire stainless steel mesh Mesh Size and description, BS 410/ISO 3310 560 micron 560 micron 600 micron 630 micron 710 micron 800 micron 850 micron 900 micron 1 mm 1.12 mm 1.18 mm 1.25 mm 1.40 mm 1.60 mm 1.70 mm 1.80 mm 2.00 mm 2.24 mm 2.36 mm 2.50 mm 2.80 mm 3.15 mm 3.35 mm 3.55 mm 4.00 mm 4.50 mm 4.75 mm 5.00 mm 5.60 mm 6.30 mm 6.70 mm 7.10 mm 8.00 mm 9.00 mm 9.50 mm 10.00 mm 11.2 mm Sieve Size 200 mm dia Product code SL 0303 SL 0304 SL 0305 SL 0306 SL 0307 SL 0308 SL 0309 SL 0310 SL 0311 SL 0312 SL 0313 SL 0314 SL 0315 SL 0316 SL 0317 SL 0318 SL 0319 SL 0320 SL 0321 SL 0322 SL 0323 SL 0324 SL 0325 SL 0326 SL 0327 SL 0328 SL 0329 SL 0330 Sieve Size 300 mm dia Product code SL 0331 SL 0332 SL 0333 SL 0334 SL 0335 SL 0336 SL 0337 SL 0338 SL 0339 SL 0340 SL 0341 SL 0342 SL 0343 SL 0344 SL 0345 SL 0346 SL 0347 SL 0348 SL 0349 SL 0350 SL 0351 SL 0352 SL 0353 SL 0354 SL 0355 SL 0356 SL 0357 SL 0358 www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 Woven wire stainless steel mesh Mesh Size and description, BS 410/ISO 3310 12.5 mm 13.2 mm 14.00 mm 16.00 mm 18.00 mm 19.00 mm 20.00 mm 22.4 mm 25.00 mm 26.5 mm 28.00 mm 31.5 mm 35.5 mm 37.5 mm 40.00 mm 45.00 mm 50.00 mm 53.00 mm 56.00 mm 63.00 mm 71.00 mm 75.00 mm 80.00 mm 90.00 mm 100.00 mm 106.00 mm 112.00 mm 125.00 mm 13 Geotechnical Testing Equipment Soil Equipment Testing Sieves Testing Sieves Standards: EN 933-2, ISO 3310-1, ISO 3310-2, ISO 565 Standards: EN 933-2, ISO 3310-1, ISO 3310-2, ISO 565 14 Sieve Size 200 mm dia Sieve Size 300 mm dia Perforated plate mild steel plate sieve Product code Product code Mesh Size and description, BS 410/ISO 3310 SL 0359 SL 0360 SL 0361 SL 0362 SL 0363 SL 0364 SL 0365 SL 0366 SL 0367 SL 0368 SL 0369 SL 0370 SL 0371 SL 0372 SL 0373 SL 0374 SL 0375 SL 0376 SL 0377 SL 0378 SL 0379 SL 0380 SL 0381 SL 0382 SL 0383 SL 0384 SL 0385 SL 0386 SL 0387 SL 0388 SL 0389 SL 0390 SL 0391 SL 0392 SL 0393 SL 0394 SL 0395 SL 0396 SL 0397 SL 0398 SL 0399 SL 0400 SL 0401 SL 0402 SL 0403 SL 0404 SL 0405 SL 0406 SL 0407 SL 0408 SL 0409 SL 0410 SL 0411 SL 0412 SL 0413 SL 0414 SL 0415 SL 0416 SL 0417 SL 0418 SL 0419 SL 0420 SL 0421 SL 0422 SL 0423 SL 0424 SL 0425 SL 0426 SL 0427 SL 0428 SL 0429 SL 0430 SL 0431 SL 0432 4.00 mm 4.50 mm 4.75 mm 5.00 mm 5.60 mm 6.30 mm 6.70 mm 7.10 mm 8.00 mm 9.00 mm 9.50 mm 10.00 mm 11.2 mm 12.5 mm 13.20 mm 14.00 mm 16.00 mm 18.00 mm 19.00 mm 20.00 mm 22.4 mm 25.00 mm 26.50 mm 28.00 mm 31.5 mm 35.50 mm 37.50 mm 40.00 mm 45.00 mm 50.00 mm 53.00 mm 56.00 mm 71.00 mm 75.00 mm 80.00 mm 90.00 mm 100.00 mm Sieve Size 200 mm dia Product code SL 0433 SL 0434 SL 0435 Sieve Size 300 mm dia Product code SL 0436 SL 0437 SL 0438 Perforated plate mild steel plate sieve Mesh Size and description, BS 410/ISO 3310 106 mm 112 mm 125 mm Testing Sieves Standards: ASTM E11 ASTM E11 sieves are similar in construction to those used in the British Standard range. Two frame sizes are available as standard, 8 inch or 12 inch diameter. Sieve Size 8 inch dia Product code SL 0439 SL 0440 SL 0441 SL 0442 SL 0443 SL 0444 SL 0445 SL 0446 SL 0447 SL 0448 SL 0449 SL 0450 SL 0451 Sieve Size 12 inch dia Product code SL 0452 SL 0453 SL 0454 SL 0455 SL 0456 SL 0457 SL 0458 SL 0459 SL 0460 SL 0461 SL 0462 SL 0463 SL 0464 www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 Woven wire stainless steel mesh Mesh Size and description, ASTM 20 micron - no. 635 25 micron - no. 500 32 micron - no. 450 38 micron - no. 400 45 micron - no. 325 53 micron - no. 270 63 micron - no. 230 75 micron - no. 200 90 micron - no. 170 106 micron- no. 140 125 micron - no. 120 150 micron - no. 100 180 micron - no. 80 15 Geotechnical Testing Equipment Soil Equipment Testing Sieves Testing Sieves Standards: ASTM E11 Standards: Standards: ASTM E11 Sieve Size 8 inch dia Product code SL 0465 SL 0466 SL 0467 SL 0468 SL 0469 SL 0470 SL 0471 SL 0472 SL 0473 SL 0474 SL 0475 SL 0476 SL 0477 SL 0478 SL 0479 SL 0480 SL 0481 SL 0482 SL 0483 SL 0484 SL 0485 SL 0486 SL 0487 SL 0488 SL 0489 SL 0490 SL 0491 SL 0492 SL 0493 SL 0494 SL 0495 SL 0496 SL 0497 SL 0498 SL 0499 SL 0500 SL 0501 16 Sieve Size 12 inch dia Product code SL 0502 SL 0503 SL 0504 SL 0505 SL 0506 SL 0507 SL 0508 SL 0509 SL 0510 SL 0511 SL 0512 SL 0513 SL 0514 SL 0515 SL 0516 SL 0517 SL 0518 SL 0519 SL 0520 SL 0521 SL 0522 SL 0523 SL 0524 SL 0525 SL 0526 SL 0527 SL 0528 SL 0529 SL 0530 SL 0531 SL 0532 SL 0533 SL 0534 SL 0535 SL 0536 SL 0537 SL 0538 Woven wire stainless steel mesh Mesh Size and description, ASTM 212 micron - no. 70 250 micron - no. 60 300 micron - no. 50 355 micron - no. 45 425 micron - no. 40 500 micron - no. 35 600 micron - no. 30 710 micron - no. 25 850 micron - no. 20 1.00mm- no. 18 1.18mm- no. 16 1.40mm- no. 14 1.70mm- no. 12 2.00mm- no. 10 2.36mm - no. 8 2.80mm - no. 7 3.35mm - no. 6 4.00mm - no. 5 4.75mm - no. 4 5.60mm - no. 3 ½ 6.30mm - 1/4 inch 6.70mm 0.265 inch 8.00mm - 5/16 inch 9.50mm - 3/8 inch 11.2mm - 7/16 inch 12.5mm - 1/2 inch 13.2mm 0.530 inch 16.0mm - 5/8 inch 19.0mm - 3/4 inch 22.4mm - 7/8 inch 25.0mm - 1 inch 26.5mm - 1.06 inch 31.5mm - 1 1/4 inch 37.5mm 1 1/2 inch 45.0mm 1 3/4 inch 50.0mm - 2 inch 90.0mm 3 1/2 inch Sieve Size 8 inch dia Product code SL 0539 Sieve Size 12 inch dia Product code SL 0544 SL 0540 SL 0541 SL 0542 SL 0543 SL 0549 75 μm Washing Sieve 8 in diameter x 8 in deep SL 0550 75 μm Washing Sieve 200 mm diameter, 200 mm deep Woven wire stainless steel mesh Mesh Size and description, ASTM 100mm - 4 inch SL 0545 SL 0546 SL 0547 SL 0548 106mm - 4.24 inch 125mm - 5 inch Lid Receiver Accessories: SL 0551 Sieve Brush, double-ended, brass and nylon bristle SL 0552 Sieve Brush, nylon, double-ended Ultrasonic cleaning bath Standards: ASTM E11 The Ultrasonic cleaning baths use cavitation to remove dirt from objects that are immersed in the cleaning liquid. Cavitation is the sequential formation and collapse of vapour bubbles and voids in a liquid subjected to acoustic energy at high frequency and intensity. Cavitation occurs wherever the liquid penetrates, ensuring that the smaller and larger aperture sieves are cleaned equally well. Ultrasonic baths are also useful for cleaning fragile items such as glassware. Cleaning baths are manufactured from stainless steel, supplied complete with a 0 - 15 minute timer, lid and incorporate an ultrasonic generator which is suitable for continuous operation.. SL 0553 Ultrasonic Cleaning Baths 25 lt capacity SL 0554 cleaning Liquid, 5 lt The 25 litre cleaning bath has an internal diameter of 410mm and a height of 200mm, accommodating sieves of up to 400mm diameter. www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 17 Geotechnical Testing Equipment Speedy Moisture Meter Standards: BS 812, ASTM D4944, AASHTO T217 The Speedy Moisture is a portable system comprising a vessel with an integral pressure gauge a weighing scale and a carry case. A small sample of the material is prepared, weighed and placed into the vessel. The reagent is then added and the vessel is sealed and shaken to mix the reagent with the sample. Free moisture within the sample reacts with the reagent to produce a gas and pressure rise within the vessel that is proportional to the amount of moisture. Soil Equipment SL 0555 Small Speedy, 6 gr sample SL 0556 Small Speedy, 20 gr sample SL 0557 Calcium Carbide The moisture content value is then read directly from the calibrated pressure gauge. Cone Penetrometer Test Standards: BS 1377, 1924-2, EN DD ENV 1997-2 The Cone Penetrometer is used to carry on liquid limit tests on soil samples. It is a static test depending on the soil shear strength. The test is based on the relationship between moisture content and the penetration of a cone into the soil sample under pre-set conditions. Speedy vessel manufactured from cast aluminium and fitted with a calibrated pressure gauge with a moisture measurement range of 0 - 20%. with 0.2% Gauge divisions. SL 0567 Manual operated Cone Penetrometer Supplied complete penetration needle and sample cups SL 0568 Semi-Automatic Cone Penetrometer Supplied complete penetration needle and sample cups SL 0569 Fully Automatic Cone Penetrometer Supplied complete penetration needle and sample cups Determination of Plastic Limit Universal Carbide Meter Standards: ASTM D4318, AASHTO T90, BS 1377:2 Standards: BS 812, ASTM D4944, AASHTO T217 The moisture content can be determined using the Moisture tester based on the calcium carbide method. The soil sample is introduced in the bottle with the reagent. The water reacts with calcium carbide and develops a gas pressure, which is indicated on the manometer and easily converted in percentage of moisture. The plastic limit (WP) is defined as the lowest moisture content of a soil that will permit a sample to be rolled into threads of 3 mm diameter without the threads breaking. SL 0558 Small Carbide Meter, 10 gr sample SL 0559 Medium Carbide Meter, 20 gr sample SL 0560 Large Carbide Meter, 50 gr sample SL 0561 Calcium Carbide reagent ampoules pack of 100 pieces Determination of Shrinkage Limit Standards: ASTM D427, AASHTO T92, BS 1377 Standards: BS 1377:2, ENV 1997-2, ASTM D4318, AASHTO T89 It helps in the classification of soil when comparing the potential properties of soil material against empirical data. Consists of a removable brass cup, adjustable crank, mechanical blow counter, and base. 18 SL 0562 Manual Liquid Limit complete with counter, metal grooving tool and test gauge, BS Standard SL 0563 Motorised Liquid Limit complete with counter, metal grooving tool and test gauge, BS Standard SL 0564 Manual Liquid Limit complete with counter, less ASTM Standard SL 0571 Glass Plate The Plastic Limit Set comprises of a glass plate, steel rod, mixing dish, spatula and 4 moisture content tins. Liquid Limit Devices: Casagrande Method Used to determine the moisture content at which clay soils pass from a plastic to a liquid state. SL 0570 Plastic Limit complete test set When the water content of a finegrained soil is reduced below the plastic limit, shrinkage of the soil mass continues until the shrinkage limit is reached. SL 0565 ASTM Metal Grooving Tool SL 0566 AASHTO Casagrande Grooving Tool This method of test covers the determination of the shrinkage limit, shrinkage ratio, volumetric shrinkage and linear shrinkage. The set comprises prong plate, shrinkage dish, spatula, glass measuring cylinder and two moisture content tins. SL 0572 Shrinkage Limit complete test set www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 19 Geotechnical Testing Equipment Linear Shrinkage Mould Soil Equipment Falling Head Permeameter Apparatus Standards: BS 1377:2 The Linear Shrinkage test covers the determination of the shrinkage of soils and indicates the plastic properties of soils with low clay content. SL 0573 Linear Shrinkage Mould SL 0574 Vernier Caliper Linear Shrinkage Mould 140 mm long, 12.5 mm radius. weight: 300 g. Voluvessel, 1/20 cu. ft. (1600ml) capacity Standards: ASTM D2167; AASHTO T205 The Voluvessel determine the in-place density of compacted or firmly-bonded soils using a rubber balloon apparatus viewed through a graduated, direct-reading clear plastic cylinder protected by metal casing. The model features a plastic cylinder, which screws into the density plate with the pump assembly mounted to the base. The Voluvessel comes with a pressure-vacuum pump assembly, pressure gauge, quick coupler valve, double graduated cylinder, 10 balloons and a density plate. SL 0575 Voluvessel complete test set. SL 0576 Spare Balloons, for use with Voluvessel Apparatus. Pack of 10 Guelph Permeameter Apparatus Standards: ASTM D5126 The Guelph Permeameter is use for measuring in-situ hydraulic conductivity. Accurate evaluation of soil hydraulic conductivity, soil captivity, and matrix flux potential can be made in all types of soils. SL 0577 Guelph Permeameter Complete Set 20 Comprises: - Permeameter field tripod - Well auger - Well preparation - Cleanup tools - Collapsible water container - Vacuum test hand pump - Durable carrying case The Falling Head Permeameter apparatus is used to determine the permeability of clay-like or silty soils. The specimen is confined within the permeameter which is connected to the manometer tube filled with water. The sample must be completely satured with water before the test, and the operator will check the rate of fall of the water in the tube passing through the test specimen. The set consists of Manometer tubes and stand with three tubes each dia. 3, 4 and 6 mm for the different degrees of permeability, soaking reservoir with cock, tubing and connectors. Permeameter dia. 4” complete with perforated plates and stainless steel gauze. SL 0578 Permeameter dia. 6” complete with perforated plates and stainless steel gauze SL 0579 De-airing tank 20 litre capacity made from acrylic plexiglass SL 0580 Water trap to collect the water condensation SL 0581 Portable vacuum pump, 230 V 1ph 50 Hz SL 0582 Rubber tubing for vacuum, 3 m long Constant Head Permeameter Apparatus Standards: BS 1377:5 ; ASTM D2434 ; AASHTO T215 The Constant Head Pemeameter apparatus is used for testing the permeability of granular soils (sand and gravels). The specimen is formed in a permeability cell and water is passed through it from a constant level tank. Take off point located along the sides of the permeability cell are connected to three manometer tubes mounted on a panel complete with a metre scale. Water passing through the specimen is collected and meansured, either for a specific quality or over a period of time. The reduction of head is noted from the variation of water level in the manometer tubes. SL 0583 Manometer tubes and stand, comprising three tubes of constant bore, graduated scale, tubing and connectors. SL 0584 Constant head permeability cell 75 mm dia., with three pressure take-off points. SL 0585 Constant head permeability cell 114 mm dia., with six pressure take-off points and an additional six blanked-off pressure points. SL 0586 Constant level tank, www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 21 Geotechnical Testing Equipment Gas Jar Method: End-Over-End Shaker Mechanical Analysis Stirrer Standards: BS ASTM D422;AASHTO T88 Standards: BS 1377:2, EN 1997-2 The The End over End Shaker is used to determine the specific gravity of soils containing up to 10% particles retained on a 37.5 mm sieve, it rotates two gas jars at approx 50 rpm to satisfy BS Standard. The shaker is equipped with an original friction device. 220 V, 50-60 Hz, 1 ph Soil Equipment SL 0587 End-over-End Shaker SL 0588 Gas Jar 1 litre capacity complete with rubber bung and glass cover The compact, bench-top mechanical stirrer is used for dispersing soil samples in water for hydrometer analysis. The stirrer is supplied complete with Mixing Paddle and Dispersion Cup. SL 0594 Mechanical Analysis Stirrer SL 0595 Soil Hydrometer BS/EN, graduated 0.0995 to 1.030 g/ml. Mechanical End-over-End Shaker Standards: BS 1377, EN 1997-2 The Particle density or specific gravity is a measure of the actual particles which make up the soil mass and is defined as the ratio of the mass of the particles to the mass of the water they displace. SL 0589 Mechanical End-over-End Shaker SL 0590 Gas Jar 1 litre capacity complete with rubber bung and glass cover This method is suitable for soils containing up to 10% of particles retained on a 37.5 mm BS sieve. Sedimentation Hydrometer Apparatus Standards: BS 1377, ASTM D422, AASHTO T88 The Sedimentation Hydrometer apparatus is used to determine particle size distribution in soil from the coarse sand size down to the smallest fractions. Hydrometer readings are taken after regular intervals. Sedimentation time and hydrometer readings are used to determine the grain sizes according to the Stoke’s Law. In this method the sample is cleaned from organic matter after which it is dried and weighed. Next it is suspended in water and sieved. The solution that passes through the sieve is transferred to a measuring cylinder with water. SL 0591 Constant Temperature Bath SL 0592 Sodium Hexametaphosphate 500 g SL 0593 Hydrometer Sedimentation Cylinder 1000 ml 22 SL 0596 Soil Hydrometer ASTM/AASHTO (152H) graduated –5 to +60 g/litre. SL 0597 Soil Hydrometer ASTM D422 (151H) graduated 0.0995 to 1.038 g/ ml.+60 g/litre. Pyknometer Methods Standards: BS 1377, 812-2, EN 1097-7, 1997-2, ASTM D 854, AASHTO T100 The Pyknometer Method is used to determine the specific gravity of clays, sand and gravel of size smaller than 10mm. Specific gravity is the ratio of weight to volume of a specific material in air and in water at a constant temperature. SL 0598 Density Bottle 25 ml, Supplied complete with capillary vent stopper. SL 0599 Density Bottle 50 ml, Supplied complete with capillary vent stopper. SL 0600 Density Bottle 100 ml, Supplied complete with capillary vent stopper. SL 0601 Pyknometer 1000 ml, Glass jar complete with non-corrodible cone and rubber seal. SL 0602 Spare Rubber seal Magnetic Stirrer Standards: EN 933–8, ASTM D2419, AASHTO T176 The magnetic stirrer hotplates are specifically designed for laboratory usage. Available in a choice of either robust aluminium or chemically resistant ceramic top, each is equipped with a range of advanced safety and communication features. To alert the user, a “Hot” warning light will flash whenever the plate temperature is above 50°C. Powerful magnets and motor give stirring speed up to 1500rpm and volumes up to 15 litres. The units automatically detect when the contact thermometer is plugged in and is visible by an illuminated LED on the hotplate, providing reassurance that the temperature of the sample is precisely controlled at all times. SL 0603 Magnetic Stirrer complete test set www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 23 Geotechnical Testing Equipment Sand Equivalent Test Sand Replacement Standards: EN 933–8, ASTM D2419, AASHTO T176 The Sand Equivalent Test indicates the relative portion of undesirable clay-like or plastic fines and dusts that occur in granular soils and fine aggregates passing the No. 4 sieve. The sample to be tested is placed in a special solution of calcium chloride, formaldehyde and glycerine. After shaking the cylinder, it is allowed to stand for a 20-minute sedimentation period. Readings are then taken on the cylinder scale for the level of the top of the clay suspension and for the sand level. The “Sand Equivalent” is the sand reading divided by the clay reading x 100. When the water content of a fine-grained soil is reduced below the plastic limit, shrinkage of the soil mass continues until the shrinkage limit is reached. SL 0604 Sand Equivalent Test Set Standards: EN 933–8, ASTM D2419, AASHTO T176 The Sand Replacement is used to determine the dry density of in-situ compact, fine, medium grained soils and for layers not exceeding 50 cm thickness. A circular hole is dug in the ground, all the soil from within it is collected, weighed and dried. The hole is then back-filled with standard uniform sand or fine gravel, poured from a calibrated container for calculating the volume of hole. Complete set consists of pouring cylinder, calibration container and a tray. The sand pouring cylinder is made of cast aluminum and precisely machined. The calibration container and tray are made of plated sheet steel. SL 0608 Sand Replacement Set 100 mm SL 0609 Sand Replacement Set 150 mm SL 0610 Sand Replacement Set 200 mm Standards: BS 1377, 1924, 812, EN 932-1, 933-3, ASTM C72 Riffle Boxes are used for dividing soil aggregates into representative sample increment for testing. Heavy Duty Electrostatic painted and manufactured from heavy gauge sheet metal the slot widths and number of slots as required in the standards. Riffle boxes are supplied complete with 3 containers easy to handle. The Sand Equivalent Shaker is recommended for laboratories performing sand equivalent tests on a regular basis. The shaker is used for uniform shaking of Sand Equivalent Measuring Cylinders. Provides shaking action at the specified rate and stroke. Supplied complete with built in timer. SL 0611 Slot Width 7 mm 2,2 kg SL 0612 Slot Width 13 mm 6,2 kg SL 0605 Sand Equivalent Shaker Sand Cone Density Standards: ASTM D1556, AASHTO T191 24 Standards: BS 1377:9, 1924:2 Riffle Boxes Sand Equivalent Shaker The Sand Cone Density is used for on site determination of the degree of compaction of sand. Complete set includes double cone, plastic sand jar 5lt capacity and metal tray. Soil Equipment SL 0606 Sand Cone Density complete set SL 0607 Standard Sand, 600/300 μm, 50 Kg. SL 0613 Slot Width 15 mm 8 kg SL 0614 Slot Width 19 mm 9,5 kg SL 0615 Slot Width 25 mm 12,5 kg SL 0616 Slot Width 30 mm 19,9 kg SL 0617 Slot Width 38 mm 21 kg SL 0618 Slot Width 45 mm 24,7 kg SL 0619 Slot Width 50 mm 26,8 kg SL 0620 Slot Width 64 mm 32,1 kg SL 0621 Slot Width 75 mm 35,3 kg Gilson Sample Splitter Standards: ASTM D427, AASHTO T92, BS 1377 The Gilson Sample Splitter is rugged, large-capacity floor model for field or lab use. Features adjustable chutes and gate release hopper. Particle sizes from 60 microns to 6 inch, Includes 2 pans. SL 0622 Gilson Sample Splitter www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 25 Geotechnical Testing Equipment Plate Bearing Test Equipment Consolidation Apparatus Standards: ASTM D 1194, D1195, D1196, BS 1377:9 The Plate Bearing Test is used to determine the bearing capacity of a soil under field loading conditions for a specific loading plate and depth of embedment. It is also used for load tests of soil and flexible pavement components. The Basic test set unit is supplied complete with 2.4 meter long datum bar. 3 dial gauges (50 mm) hydraulic cylinder 500 KN with hand pump, pressure gauge, Soil Equipment Standards: BS 1377:5 / ASTM D2435, D3877, D4546, AASHTO T216 connections and 300 mm diameter loading plate. SL 0623 Plate Bearing Complete Set SL 0624 300mm dia loading plate SL 0625 450mm dia loading plate SL 0626 600 mm dia loading plate SL 0627 760 mm dia loading plate SL 0630 Consolidation Frame SL 0631 Floor-mounting stand securing up to three Consolidation Frames. SL 0632 Set of weights (4x10 kg, 1x5 kg, 2x2 kg, 1x1kg) Consolidation Cells SL 0633 Consolidation cell, 50 mm complete SL 0634 Consolidation cell, 75 mm complete SL 0635 Consolidation cell, 2.5 inch complete SL 0636 Floating Ring Consolidation Cell 63.5 mm (2.5 in) diameter sample. Electrical Density Gauge Standards: ASTM D6938, D2950, C1040 and AASHTO T310 The electrical density gauge measures pavement density indirectly by measuring its dielectric constant. It passes a small current through the pavement, which creates an electrical sensing field. Density is measured by the response of this electrical sensing field to changes in the pavement’s complex impedance (consisting of the pavement’s composite resistivity and dielectric constant). The advantage of using the electrical density gauge is that the readings can be obtained in seconds. It contains no radioactive source and therefore not subject to radiological controls. More effective cost control, no licensing or special training needed, easier to use, light in weight. SL 0628 Electrical Density Gauge Nuclear Density Gauge Standards: ASTM D6938, D2950, C1040 and AASHTO T310 The Nuclear Density Gauge that is better in performance than any other gauge on the market today with the lowest maintenance and operating costs. Operation is straightforward and uncomplicated. Menu options are easy to read and navigate. A backlit LCD screen and special scroll functions allow operators to easily read. 26 Measurement of Movement The gauge uses an advanced micro-processor-based technology to provide highly-accurate measurements of density and moisture that are automatically computed for direct readouts of wet density, dry density, moisture content, percent of moisture, percent of compaction (Proctor or Marshall), void ratio and air voids. The One-dimensional Consolidation test is used to determine the consolidation characteristics of soils of low permeability. The consolidation is rigidly constructed to ensure minimum frame distortion. The frame is designed to load the specimen through a yoke assembly and one of three alternative beam ratios as 9:1 – 10:1 and 11:1. The beam is fitted with a counter balance weight and beam support check. The cell platform will accept the complete range of consolidation cells and is fitted with a central spigot to ensure accurate centering of the cell under the loading yoke. The fixed ring consolidation cells are manufactured from corrosionresistant materials and conform to the requirements of the relevant standards. An integral water reservoir is incorporated in the cell which allows the specimen to be inundated when required. SL 0637 Dial Gauge BS, 10 x 0,001 mm div SL 0638 Dial Gauge ASTM, 0.5 x 0.0001 inch div SL 0639 Displacement Transducer, BS SL 0640 Displacement Transducer, ASTM SL 0641 Data Logger Spare SL 0642 Cutting ring SL 0643 Calibration disc SL 0644 Upper porous disc SL 0645 Lower porous disc SL 0629 Nuclear Density Gauge www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 27 Geotechnical Testing Equipment Soil Equipment Direct Residual Shear Apparatus Automatic Soil Compactor Standards: BS 1377, EN 1997-2, ASTM D3080, AASHTO T236 Standards: BS 1377-4, 1990, EN 1997-2, 1924, 13286-2, 47, ASTM D558, 560, 698, 1557, AASHTO T99, T134, 135, 136, 180, 193 The Digital Residual Direct Shear Apparatus is used for determination of the direct shear strength of soils specimen. The process is known as shear failure and occurs when shear stresses set up in the soil mass exceed the maximum shear resistance which the soil can offer, i.e. its shear strength. The Automatic Soil Compactors is designed to provide a uniform compaction of Standard, Modified and CBR specimens assuring conformity with the reference standard. The Compactor is equipped with programmable digital counter which allows machine to stop at the preset numbers of blows. The height and weight of the rammer is adjustable to suit test requirements. The drop weight is adjustable to 300 mm drop height and is also adjustable to 450 mm drop height. The rammer is circular faced with a 50 mm diameter and is adjustable to 2.5 kg. or 4.5 kg. An automatic blow pattern ensures effective compaction for each layer of soil and the rammer travels across the mould. Comprises: Direct Shear box, floor mounted with carriage assembly and load hanger with 10:1 lever loading device. Microprocessor controlled digital motor with digital keyboard display and return datum facility. Variable speed over the range of 0.00001 to 9.99999mm/minute. Fast forwar reverse 10 mm per minute. SL 0646 Digital Direct Residual Shear Apparatus, Supplied without shearbox, load ring, vertical and horizontal dial gauges. SL 0647 Slotted Weights, 50 kg Set of Weights Measurement of Load SL 0648 Compression Load ring, 2 KN SL 0649 Compression Load ring, 5 KN SL 0650 S-type Load Cell, 5 KN Measurement of Movement SL 0651 Vertical Dial Gauge, 10 x 0,01mm SL 0652 Horizontal Dial Gauge, 10 x 0,01mm SL 0653 Displacement Transducer 28 The table rotates the mould in equal steps and the number of blows per layer can be set at the beginning of the test by the digital counter. Drop Height: 300 mm, 305 mm, 450 mm, 457 mm (adjustable) Rammer Weight: 2.5 kg, 4.5 kg Dimensions: 640 x 340 x 1506 mm (w x l x h) Power: 220 V, 50-60 Hz, 1 ph Weight (approx.): 135 kg SL 0666 Automatic Soil Compactor BS/EN SL 0667 Automatic Soil Compactor ASTM Spares SL 0668 Rammer BS/EN, 50 mm dia, adjustable to 2.5 kg or 4.5 kg weight SL 0669 Rammer ASTM, 2 in dia, adjustable to 5.5 lb (2.5 kg) or 10 lb (4.5 kg) Dry Density, Moisture Relationship, Standard and Modified Proctor Mould Standards: BS1377-4,1924-2,1997-2,ASTM D558,559,560,698,1557 AASHTO T99, T134 T135, T136 Shear Box Assemblies SL 0654 Shear Box Assembly BS 1377, 60x60x25mm, 2 Kg SL 0655 Shear Box Assembly BS 1377, 100x100x25mm, 5.2 Kg SL 0656 Shear Box Assembly ASTM D3080, 2.5 x 1inch, 2.8 Kg Accessories and Spares SL 0657 Specimen Cutter for 60mm SL 0658 Specimen Extrusion Tool for 60mm SL 0659 Porous Disc for 60mm SL 0660 Specimen Cutter for 100mm SL 0661 Specimen Extrusion Tool for 100mm SL 0662 Porous Disc for 100mm SL 0663 Specimen Cutter for 2.5inch SL 0664 Specimen Extrusion Tool for 2.5inch SL 0665 Porous Disc for 2.5inch The Moulds are used for determining the relationship between the moisture content and density of compacted soil. Made of plated steel, includes collar, mould body and base plate. SL 0670 Standard Compaction Mould BS/EN 1 litre, 5.5 kg. SL 0671 Compaction Rammer, 50 mm dia, 2.5 kg BS/EN SL 0672 Compaction Rammer, 50 mm dia, 4.5 kg BS/EN SL 0673 Proctor Compaction Mould, 1/30 ft3 5.4 kg, ASTM SL 0674 Proctor Compaction Rammer, 2 in dia, 5.5 lb, 4.1 kg, ASTM SL 0675 ASTM Compaction Mould, 1/13.33 ft3, 8.2 kg, ASTM SL 0676 ASTM Compaction Rammer, 2 in dia, 10 lb, 6.3 kg, ASTM SL 0677 Straightedge, 300 mm www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 29 Geotechnical Testing Equipment Soil Equipment California Bearing Ratio Test Machine Multispeed Test Machine Standards: BS 1377, 1924, EN 13286-47, ASTM D1883, AASHTO T193 Standards: BS 1377-7, -8 1924-2,ASTM D2850 D4767, AASHTO T296 T297 The California Bearing Ratio or CBR test is used for the laboratory evaluation of the bearing value of highway sub-bases and sub-grade. The Multispeed 50 kN capacity machine has been designed primarily for performing laboratory CBR and Marshall stability on one load frame. The CBR is composed by a robust and compact two-column frame with adjustable upper cross beam driven by an electromechanical ram with a maximum capacity of 50 kN and a data acquisition and processing system. The CBR is designed to load the penetration piston into the soil sample at a constant rate to measure the applied load and piston penetration at pre-determined intervals. The ram speed can be set between 0.5mm/min to 5mm/min by using Digital Readout Unit. This main feature allows user to perform tests complying to BS / EN or ASTM standards with the same machine. Rapid adjustment of the platen is also provided. SL 0678 Digital CBR Testing Equipment 50 kN Load frame complete with Stabilising Bar. SL 0679 Spare Stabilising Bar Penetration and Measurement SL 0680 Penetration Piston. SL 0681 Penetration Dial Gauge BS, 25 mm x 0.01 mm divisions. SL 0682 Penetration and Swell Dial Gauge, ASTM 1 x 0.0005 in divisions. SL 0683 Bracket and Adaptor for CBR penetration dial gauges. SL 0684 Displacement Transducer SL 0685 Load Ring, 28 KN complete SL 0686 Load Ring, 50 KN complete Data Acquisition and Control System Standards: BS 1377, 1924, EN 13286-47, ASTM D1883, AASHTO T193 The LCD graphics Data Acquisition and Controls System (DA/CS) is designed to control the machine and to process the data from linear potentiometric transducers, Load Cells, installed on the CBR machine frame. The DA/CS compatible design satisfies the ergonomic requirements for various uses. The digital graphic display allows real time Load vs. penetration graph and value readout. At the end of the test cycle the results can be stored in the large memory or to a PC by using the CBR software. 30 Dedicated real time CBR software package is available for testing and further data processing, database management and certificate printing. Specification: •Calculates corrected CBR value at 2,5mm and 5mm •Large memory up to 100 tests •RS232 connection serial port for connecting either PC or printer for data transmission •Two analogical channels, for Load Cell Linear and potentiometer transducer SL 0687 Data Acquisition and Controls Sys It is particularly suitable for those laboratories carrying out a mix of these tests, e.g. for road construction. The compact bench mounting design comprises a twin column frame incorporated into the motorised drive system. The Upper beam can be adjusted in height. A robustly constructed case houses the drive system with careful attention being given to the prevention of ingress of water or grit. All operating controls are mounted on the front panel of the machine. The frame provides two fix speed ranges, easily selectable by a gear control switch. An emergency stop is installed as an extra safety feature. Foreseen electric end of stroke switches of the load plate to save the machine from wrong manipulations. Digital Display is also available. Speeds of operation vary between: 1,27 mm/min. for CBR tests. 50,8 mm/min for Marshall tests. SL 0688 Multispeed 50 kN capacity Machine SL 0689 Multispeed 50 kN capacity Machine with digital display In-situ California Bearing Ratio Apparatus Standards: BS 1377, 1924, EN 13286-47, ASTM D1883, AASHTO T193 The in-situ California Bearing Ratio is used for the evaluation of the bearing capacity of soil from a vehicle on site immediately and with less delay. Rigid and stable frame, made from corrosion-proof steel. SL 0690 In-situ California Bearing Ratio 50 KN Conversion Frame BS/EN SL 0691 50 KN Load Ring complete SL 0692 Bracket and Adapter SL 0693 50 kN Capacity Mechanical Jack SL 0694 Datum Bar Assembly SL 0695 4.5 kg Annular Surcharge Weight SL 0696 4.5 kg Slotted Surcharge Weight SL 0697 Set of Extension Rods SL 0698 Ball Seating with Connections SL 0699 CBR Penetration Piston SL 0700 Penetration Dial Gauge www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 31 Geotechnical Testing Equipment Soil Equipment Expansion Swell Test Equipmen Triaxial Testing Apparatus Standards: BS 1377:2 Standards: BS 1377-7,8 1924-2, ASTM D2850 D4767 AASHTO T296 T297 The Swell Test Equipment is placed on top of the soil sample to enable monitoring of swelling. The swell test consists of perforated plate with adjustable stem (swell plate) dial gauge tripod and dial gauge. SL 0701 Swell Plate with adjustable stem SL 0702 Swell Tripod for mounting Swell dial gauge on the CBR mould collar SL 0703 Dial Gauge 20mm x 0.01 mm CBR Mould and Accessories Standards: BS 1377, 1924, EN 13286-4, EN 1997-2, ASTM D1883, AASHTO T193 The range of moulds and accessories specifically designed to meet the requirements of the relevant stadards. The moulds and accessories are manufactured from high quality, long-lasting material and with proper maintenance will give years of satisfactory performance. CBR Mould BS/EN: SL 0704 CBR Mould Body complete with collar and perforated baseplate BS/EN SL 0705 CBR Extension Collar, BS/EN SL 0706 CBR Solid Baseplate, BS/EN CBR Mould ASTM: SL 0707 CBR Mould Body complete with collar and perforated baseplate ASTM SL 0708 CBR Extension Collar, ASTM SL 0709 CBR Solid Baseplate, ASTM 32 Accessories For CBR Mould BS/EN: SL 0710 CBR Perforated Baseplate, BS/EN Plated steel 150mm diameter x 120mm body height SL 0711 CBR Cutting Collar to fit BS/EN mould body SL 0712 Pair of C-spanner to fit BS/EN CBR moulds and collars SL 0713 Baseplate Tool BS/EN SL 0714 Static Compaction Plug BS/EN SL 0715 2 kg Annular Surcharge Weight BS/EN SL 0716 2 kg Split Surcharge Weight, BS/EN SL 0717 Tamping Rod SL 0718 Filter Papers, 150 mm diameter. Box of 100 The Triaxial Testing Apparatus test soil samples for the following applications: · Unconsolidated Undrained (UU) · Consolidated Undrained (CU) · Consolidated Drained (CD) · Unconfined Compression (UC) The Triaxial Testing Apparatus consists of a 50 KN capacity Load Frame, Platen adaptors, dial gauge or digital transducer assembly, Triaxial Cell, Base and pressure system. The Triaxial Testing Apparatus provide variable speed from 0.399999” (9.99999 mm) per minute to as low as 0.000001” (0.00001 mm) per minute. SL 0725 Digital Triaxial Load Frame, 50 KN complete SL 0726 Platen Adaptor SL 0727 Unconfined Compression Platens and Dial Gauge Mounting Assembly SL 0728 Dial Gauge 25 mm travel x 0.01 mm SL 0729 Dial Gauge 50 mm travel x 0.01 mm SL 0730 Displacement Transducer, 50 mm An electronic control system with touch-sensitive keypad for precise setting, control and viewing of all load frame functions. The Data Acquisition and Controls System (DA/CS) for automated data acquisition and recording of test parameters supplied with complete set of Electronic Measurement Transducers for load, displacement, pressure and volume change. The Triaxial Software for recording, analysis and report generation, master control panel and de-aired water tank system for precise applications of confining, back and saturation pressures. Accessories: SL 0738 Grease Gun Supplied complete with one tube of silicone grease lubricant. SL 0739 Silicone Grease Lubricant Tube SL 0740 Piston Resistant Clamp Triaxial Cells: SL 0731 Triaxial Cells, 50 mm SL 0732 Triaxial Cells, 70 mm SL 0733 Triaxial Cells, 100 mm SL 0734 Triaxial Cells Base Adaptors, 38 mm SL 0735 Triaxial Cells Base Adaptors, 50 mm SL 0736 Triaxial Cells Base Adaptors, 70 mm SL 0737 Triaxial Cells Base Adaptors, 100 mm Accessories For CBR Mould ASTM: SL 0719 CBR Cutting Collar to fit mould body ASTM SL 0720 CBR Spacing Disc ASTM SL 0721 Baseplate Tool ASTM SL 0722 5 lb Annular Surcharge Weight ASTM SL 0723 5 lb Split Surcharge Weight ASTM SL 0724 Filter Papers, 150 mm diameter. Box of 100 Sample Preparation: Sample Diameter 38 mm 50 mm 70 mm 100 mm O-Ring placing tool Suction membrane device Two-way split former Two-part split mould 10 ml single-tube drainage burette Valve complete with 6 mm connector Tubing and Connector Rubber membrane (pack of 10) Membrane sealing ring (pack of 10) SL 0741 SL 0742 SL 0743 SL 0744 SL 0745 SL 0746 SL 0747 SL 0748 SL 0749 SL 0750 SL 0751 SL 0752 SL 0753 SL 0754 SL 0755 SL 0756 SL 0757 SL 0758 SL 0759 SL 0760 SL 0761 SL 0762 SL 0763 SL 0764 SL 0765 SL 0766 SL 0767 SL 0768 SL 0769 SL 0770 SL 0771 SL 0772 SL 0773 SL 0774 SL 0775 SL 0776 www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 33 Geotechnical Testing Equipment Soil Equipment Deaired Water Apparatus Oil/Water Pressure System Standards: BS1377-7, BS1377-8 Standards: BS 1377 The compact self-contained unit will deair water quickly and efficiently down to levels of dissolved oxygen acceptable for the use in soil testing laboratories, triaxial tests, saturation and permeability tests. it is particularly important that water from which dissolved air has been removed is used in the pore pressure measurement system. Any dissolved air in the water will lead to errors in the measurement of pore pressure, particularly at low pressures. The deair water apparatus remove air from the water by a vacuum system which continuously circulates the water in the tank. The Oil/Water Pressure System provides an infinitely variable constant pressure from 0 to 3500 kPa, by using a motorised hydraulic pump, an oil/water interchange vessel, piston/spring and valves with high viscosity oil. The unit is supplied with a clear water container which will hold a maximum of 15 litres of water. Input and output lines are formed using standard 6 mm tube connectors. Supplied complete with precision pressure gauge, range 0-3500 KPa. with a control accuracy of better than ± 2.0 kN/m² of the indicated set pressure. SL 0777 Deaired Water Apparatus SL 0778 Spare Water Tank SL 0779 Nylon Tubing, 6mm bore dia 1 meter length Microspear, Moisture and Temperature Air/Water Pressure System To distribute pressure water “up to 1700 kPa.” Simple, practical and extremely accurate to select tests pressure, it can also offer the possibility to further system expansions. The cell set includes a high pressure air inlet attachment, “a high accurate regulator which enables to set the work pressure and 4 valves for pressure water outlet, water and air drain.” The cell membrane enables the use of deaerated water. A suitable compressor, which can grant a pressure source, is necessary for using the air/water membrane cell. Air/Water panels are used with an interface to convert air pressure from a standard compressor into water pressure. Bladder Air/Water Cylinder. 34 SL 0787 Oil/Water Pressure Apparatus SL 0788 Universal Pump and Pressure Indicating Panel SL 0789 Oil, 2 Litres SL 0782 Two-way Pneumatic Pressure Regulator Panel SL 0783 Four-way Pneumatic Pressure Regulator Panel SL 0784 Six-way Pneumatic Pressure Regulator Panel SL 0785 Air Compressor, 1000 kpa SL 0786 Filter Unit for Compressor The instrument measures moisture and temperature of minerals and building materials at depths up to six feet (nearly 2 meters) - simply by insertion. The digital readings are shown instantly. It has a built-in computer which gives it the flexibility to handle a wide range of materials and water contents. This instrument will give you quick results and an alternative for sampling and testing using balances or ovens. Any environment where minerals or building materials are being shipped, stored or processed Specification: Measurement Response: 2 seconds Moisture Range: 0-25% Moisture Resolution: ±0.1% Moisture Accuracy: ±0.5% of reading Temperature Range: -20°C to 60°C Temperature Resolution: 0.1°C Temperature Accuracy: <0.5°C Weight: 1500g Material Selections: 6 (user configurable) Power Requirements: 4 x 1.5v AA alkaline cells (or equivalent) Shaft Colour Options: Grey / Orange / Yellow / Blue SL 0790 Microspear, 1 meter long SL 0791 Microspear, 2 meter long SL 0780 Bladder-type Air/Water Pressure Assembly SL 0781 Spare Bladder Membrain www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 35 cement equipment Cement production process Cement is one of the ancient raw materials used in construction. It is uncertain where it was first discovered that a combination of hydrated non-hydraulic lime and a pozzolan produces a hydraulic mixture (e.g., Portland cement) harden because of hydration chemical reactions that occur independently of the mixture’s water content; they can harden even underwater or when constantly exposed to wet weather. Cement is essentially a binder that binds other materials together, Modern cements are manufactured by a chemical process. 03 Raw materials are crushed, ground and blended before being heated in a rotary kiln until they combine chemically. The clinker from the kiln is then ground with gypsum to form Portland cement. Different types of cement with different strengths and characteristics can be produced depending on the composition and quality of clinker, fly ash, silica fume, retarders, water proofers, colouring agents and other additives used in the mix. It is essential to test the physical and chemical parameters of each cement batch produced and to identify the unique characteristics of each composition. Such parameters include specific surface and gravity of cement particles, consistency, soundness, setting time, heat of hydration, inorganic chemical analysis, loss on ignition, air content and strength. 37 Geotechnical Testing Equipment Cement Equipment Le Chatelier Mould Fineness Blaine Air Apparatus Standards: BS 1377:2, EN 196-6, 459-2, 13286-44, BS 4359-2, ASTM C204 Standards: BS 6463; EN 196-3, 459-2, EN ISO 9597 The Blaine Air Apparatus is used to determine the particle size of Portland cement, limes and similar powders expressed in terms of their specific surface. Le Chatelier method determines the soundness of cements and limes by using the expansion test with Le chatelier moulds according to the relevant standard. measure 150 mm from the points to the centre line of the cylinder and O-ring. Standard weight 100 g ±10 g and two glass plate are supplied complete with the mould. Comprises: The mould consists of a spring tensioned split cylinder 30 mm internal diameter x 30 mm high with two indicator stems which CM 0114 Le Chatelier Mould complete Comprises: It comprises of a stainless steel cell, perforated disc and plunger. A U-tube glass manometer is fitted to the steel stand. The set is complete with rubber aspirator and filter paper. CM 0101 Blaine Air Apparatus Accessories: CM 0102 Manometer Tube CM 0103 Reference Cement CM 0104 Filter Paper (pack of 100) CM 0105 Cell with perforated disc CM 0106 Manometer liquid bottle 250 mm Le Chatelier Water Bath Standards: EN 196-3, 459-2 Specific Gravity Le Chatelier Flask Standards: EN 196-6, ASTM C188, AASHTO T133 The Chatelier Flask is used to determine the specific gravity of hydraulic cement and lime. The Chatelier Water Bath is use with Le Chatelier moulds for the determination of the soundness of cement paste. CM 0107 Le Chatelier Flask Comprises: The Water Bath comes complete with removable rack to hold twelve moulds and cover. Build in digital Thermostat controller to regulate the water Glass flask 250ml capacity, with graduated neck from 0 to 1 ml and from 18 to 24 ml in 0.1 ml graduation with accuracy of 0.05 ml. Cement Flow Table temperature from ambient to boiling point. CM 0115 Le Chatelier Water Bath complete Vicat Apparatus Standards: BS 4551-1, 3892-1, EN 459-2, 1015-3 1015-9, 13395-1 Standards: EN 196-3, 13454-2, ASTM C187, C191, AASHTO T129, T131 The Flow Table is used for determining consistency of mortar, lime and cement specimens. The table is 300mm dia., 10mm rop height. The one made of brass has dimensions of 100mm base dia. x 70mm top dia. x 60mm high. The Vicant Apparatus is used for determining setting time and consistency of cement by Vicat Method. Comprises: The test set comprises of Vicat Frame, Vicat Mould, Initial and Final needles, glass plate and consistency plunger. CM 0108 Manual Cement Flow Table, BS, EN CM 0109 Manual Cement Flow Table, ASTM CM 0110 Automatic Cement Flow Table,BS/EN 38 CM 0111 Automatic Cement Flow Table, ASTM CM 0112 Flow Mould CM 0113 Tamping Rod CM 0116 Vicat Frame Complete CM 0117 Initial Set Needle1.13 mm dia, EN CM 0118 Final Set Needle1.13 mm dia, EN CM 0119 Initial Set Needle 1 mm dia, ASTM CM 0120 Vicat Mould, EN CM 0121 Vicat Mould, ASTM CM 0122 Consistency Plunger www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 39 Geotechnical Testing Equipment Cement Equipment Autoclave Apparatus Automatic Vicat Apparatus Standards: EN 196-3:2005, 13279-2, 480-2, ASTM C187, C191, BS 4550, AASHTO T129, T131 Standards: ASTM C151, ASTM C141, AASHTO T107 The Automatic Vicat Apparatus is designed and manufactured using the most recent and sophisticated technology, it is used for the initial and final setting time determination of cements or mortar pastes. The apparatus is manufactured with anticorrosion components to be used in places with humidity up to 90% and 20°C. The Autoclave Apparatus used for accelerated soundness tests on cement. The entire test is made in a fully automatic way and gives a very precise and repeatable result with controlled temperature as required by EN Specifications. The results are printed on the incorporated printer and this eliminates the manual operations of installing and zeroing the paper graph on the drum. The use of the appliance is extremely simplified by the guiding menu that is available in different languages. CM 0123 Automatic Vicat Apparatus Complete with EN and ASTM Initial and Final needles, Consistency Plunger, 1 x EN and ASTM Mould and Glass Plate. Accessories: CM 0124 Consistency Plunger CM 0125 Initial needle, 1.13 mm dia EN CM 0126 Final needle, 1.13 mm dia EN CM 0127 Initial needle, 1 mm dia ASTM CM 0128 Final needle, 1 mm dia ASTM CM 0129 Needle Cleaning Device CM 0130 Windows Software and RS232 Cable CM 0131 Printer Paper Rolls, pack of 10 CM 0132 Mould Tank Cement Shrinkage Test Standards: EN 1367- 4,EN 12617- 4,ASTM C151,C490,BS 1881:5,6073 The Cement Shrinkage Test is used to determine the accelerated soundness (autoclave method) and length changes of 40x40x160 mm and other sizes of cement prisms. Comprises: The set comprises of length measuring frame, two or three gang steel mould according to the related standard, steel inserts for moulds and reference rod. CM 0134 Drying, Shrinkage, Length Comparator with adjustable-height beam 40 CM 0135 Dial gauge 0,002mmx10mm CM 0136 Digital dial gauge 0.001mmx20 mm CM 0137 Reference Rod 160mm EN12617–4 CM 0138 Reference Rod 305 mm ASTM C490 CM 0139 Three Gang Prism Mould 40x40x160mm to EN12617-4 CM 0140 Two Gang Prism Mould 25x25x285 mm to ASTM C490 CM 0141 Steel Inserts, 10 pieces It provides high pressure steam up to 25 Bar to help cure the cement speciments. Comprises : The Autoclave is made of high pressure steam chamber of dimension 114 mm ID x 406,4mm Stainless steel chamber with bolted steel cover, which is enclosed in eat insulated metal housing. CM 0133 Thermostatically-controlled Heating/Cooling System, for testing samples under water as per EN 196-3. Double scale indication pressure gauge with thermostat regulator and safety valve automatically shut off with beep reminding after sterilization. CM 0142 Autoclave Apparatus Complete Spares: CM 0143 O-ring Lid Sealing Gasket CM 0144 Specimen Rack Heat of Hydration Apparatus Standards: BS 4550, ASTM C186 This Apparatus is required for determining the heat of hydration of cement as expressed in calories per gram. Comprises: A wide mouthed double walled vacuum flask with a cork stopper 38 mm thick and an insulated container for flask. A beckman thermometer held tightly by the cork stopper in such a way as to avoid accidental contact with stirrer blades and a reading lens. To facilitate removal, the cork stopper is divided into two halves. A constant speed stirrer (Doublebladed propeller type) extending to within 38 mm from the bottom of the flask. A funnel (Gooch Type) with a stem of 6 mm inner dia and a body approx 25 mm long and 25 mm dia is fitted to the cork stopper for introducing the sample. CM 0145 Heat of Hydration Apparatus Complete Accessories: CM 0146 Vacuum Dewar Flask CM 0147 Beckman Thermometer, range 6ºC ±0.01ºC CM 0148 Glass Filling Funnel www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 41 Geotechnical Testing Equipment Cement Equipment Automatic Mortar Mixer Manual Mortar Mixer Standards: EN 196-1, 196-3, 413-2, 459-2 Standards: EN 196-1, EN 196-3, EN 413-2, EN 459-2 The Automatic mixer is perfect to mix mortars and cement material according to the required standards. Thirty seconds after starting the mix the sand is automatic discharged into the mixing bowl. The Manual mixer is a basic mortar and cement mixer according to the required standards. The mixer is very rigid and durable with a planetary motion for its paddle. CM 0149 Automatic Mortar Mixer CM 0150 Automatic Sand dispenser CM 0151 Mixing Bowl 5 Ltr, Stainless Steel complies with EN 196 CM 0152 Paddle, stainless steel complies with EN 196 CM 0153 Scraper The mixer is controlled by an on/off switch. It has two different speeds that can be operated on manual mode. The mixer is electronically controlled; it has two different speeds that can be operated either on manual or automatic program mode. Flame Photometer Standards: EN196-21;ASTM C114 Automatic Digital Mortar Mixer Standards: EN 196-1, 196-3, 413-2, 459-2, ASTM C305 Automatic Digital Mortar Mixer is perfect to mix mortars and cement material according to the required standards. The mixer is has the latest technology with a programmable mixing cycles conforming to EN 196-1, EN 196-3 and ASTM C305. It has Acoustic signal synchronised with cycle steps, complete with automatic sand dispenser and Ergonomic and safe design. CM 0154 Automatic Digital Mortar Mixer complete including sand, cement and water dispencer. CM 0155 Mixing Bowl 5 Ltr, Stainless Steel complies with EN 196 CM 0156 Paddle, stainless steel complies with EN 196 CM 0157 Scraper The Flame Photometer is a device used in inorganic chemical analysis to determine the concentration of certain metal ions, among them sodium, potassium, lithium, Barium and calcium. In principle, it is a controlled flame test with the intensity of the flame colour quantified by photoelectric circuitry. The instrument is fitted with automatic flame failure detection for user safety, making it ideal for use in laboratory, industrial sites and educational applications. CM 0162 Flame Photometer supplied complete with Na, K, Ba, Ca and Li filters, connecting hoses and clips, compressor plug and drain trap Muffle Furnace, Loss on Ignition Standards: EN 196-2, EN 459-2, BS 1016:4, ASTM D2361, D2795 The Muffle Furnaces are widely used for determining various properties of construction materials such as the Loss on Ignition. Vertical lift door directs heat away from user and saves counter space. A safety interlock switch disconnects power when the door is open. Vertical lift door has maximum access with minimum head room for easy loading and unloading. 42 CM 0158 Manual Mortar Mixer CM 0159 Mixing Bowl 5 Ltr, Stainless Steel complies with EN 196 CM 0160 Paddle, stainless steel complies with EN 196 CM 0161 Scraper CM 0163 Muffle Furnace, 4.2 liters cap. 1200 C temp CM 0164 Muffle Furnace, 7.5 liters cap. 1200 C temp CM 0165 Muffle Furnace, 15 liters cap. 1200 C temp CM 0166 Muffle Furnace, 22 liters cap. 1200 C temp www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 43 Geotechnical Testing Equipment Vibrating Machine Cement Equipment Three Gang Mould Standards: BS 4550 Standards: BS 3892-1, 4551-1, EN 196-1, 413-2, 459-2, 1744-1, 1015-10,11, 13454-2. The Vibrating Machine is perfect for the preparation and compaction of 70.7 mm mortar cube specimens. The 40.1x40x160 mm Three Gang Mould is manufactured of steel with hardness over HV400 the surface is heat treated to comply with the related standards. The vibrating shaft of the machine allows each sample to be vibrated at 12000 cycles per minute. Fitted with setting timer the vibrating machine can stop automatically when set time is completed. CM 0167 Vibrating Machine CM 0170 Three Gang Mould 40.1x40x160 mm CM 0171 Feeding Hopper CM 0172 Scraper double-ended CM 0173 Standard Reference Sand. EN 196-1 2006, 1350 gram per Bag Three Gang Cube Mould Standards: BS 1881-131, ASTM C109, EN 196-1 Jolting Table The 50x50x50 mm Three Gang Cube Mould is manufactured of cast ion, all internal surfaces are machined. All dimensions and specifications comply with the related standards. Standards: EN 196-1 Jolting table is used for mould compacting of 40.1x40x160 mm cement specimens and consists of mould table seated on a rotating cam driven at 60 revolutions per minute. The Jolting Table is 15.0 mm drop equipped with counter which provides automatic shut off at end of preset drop numbers. Rapid mould lock and release system allows easy and quick operation. CM 0174 Three Gang Cube Mould This cast ion three gang mould is a diagonal arrangement 50mm mortar cube moulds with a detachable brass base plate. Wing nut clamps lock the mould to the base while stainless steel CM 0168 Jolting Table thumbscrews secure the halves tightly together. Large screed off upper surface area makes this mould a preferred choice. CM 0175 Three Gang Cube Mould with simple cube release mechanism Briquette Mould 70.7 mm Cube Mould Standards: BS 4550 Standards: EN 196-1, ASTM C109, BS 4550 The 70.7 moulds have been manufactured from steel in the relevant British Standard and all internal surfaces are machined. Supplied complete with baseplate. All dimensions and specifications comply with the related standards. 44 CM 0169 70.7 mm Cube Mould The Briquette Mould is used for casting cement briquettes for tensile strength testing. Manufactured of brass it is a two part split mould with thumb screws for quick assembling and dismantling of the mould. The minimum cross section of the briquettes cast is 25.4 mm x 25.4 mm. Supplied complete with a steel base plate. CM 0176 Briquette Mould www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 45 Geotechnical Testing Equipment Plunger Penetration Apparatus, Consistency of Masonry Cement Standards: EN 413-2, 459-2, 1015-4, DIN 4211 The plunger penetration apparatus is used to determine the consistency of fresh mortar, lime and mansory cement. The base is foreseen of a device to locate the test cup. The height of the drop can be accurately adjusted to 100 mm. Supplied complete with test cup and tamper, both made from anodized aluminium. dimension 200x200x700 mm CM 0177 Plunder Penetration Apparatus complete Spares: CM 0178 Test cup CM 0179 Tamper Cement Equipment Humidity Curing Cabinet Standards: BS 3892-1, EN 196-1 459-2 The Humidity Curing Cabinet is used for curing cement test samples. The curing cabinet provides 50 ± 0.5°C temperature and 98% humidity for cement specimens by an immersion heater and refrigerator unit which are supplied complete with the cabinet. The internal chamber and racks are made of stainless steel. The cabinet is equipped with digital control unit to monitor the temperature and humidity and recording chart. Dropping ball apparatus The apparatus consists of a dropping device mounted on a stand, acrylic ball and a 100mm diameter x 25mm deep mould. The base of the stand is machined with a Chrome finish. CM 0180 Dropping Ball Apparatus CM 0181 Ball Penetration measuring Device with dial gauge 25 x 0.01 mm Gillmore Apparatus Standards: ASTM C91, C141, C266 AASHTO T154 The Gillmore apparatus is used to determine the setting time of cement. Vertical support shaft has a device to maintain the horizontal arms in alignment. Needle points are from stainless steel. The initial setting needle has dia.2,12 mm and weight of 113 g, while the final setting needle has dia.1,06 mm and weight of 453,6 g. Support assembly is adjustable in position. The two steel weights needles are calibrated to meet Specifications. CM 0182 Gillmore Apparatus 46 320 Litres 66 x 64 x 175 49 x 51 x 127 +5.0°C to ± 0.2ºC ± 0.5ºC 7 day 0 – 50ºC 0 – 100% RH 10 shelves CM 0183 Humidity Curing Cabinet CM 0184 Recording Chart Standards: BS 4551-1, 6463-4 The dropping ball apparatus is used to measure the consistency of cement mortars, this allows a 25mmdiameter acrylic ball to fall freely from a standard height of 250mminto a brass ring mould containing a mortar specimen with a carefully prepared surface. The depth of the ball penetration into the mortar gives the specimen consistency. Specification Capacity: External Size: cm Internal size: cm Temp range: +60°C Fluctuation: Variation: Recorded chart: Temperature: Humidity: shelves: Air Content Meter for Mortar, Masonry Cement and Lime Standards: EN 459-2 The Air content meter for mortat is designed to determine the air content in cement mortar, cement paste and lime mortar. Made from cast aluminium, the test pot one litre capacity and the upper part are air-tight sealed by means of two quick action spring clamps. The whole is connected to a dial gauge directly indicating the air entrainment in percentage, with range 0 - 50%. www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 A built-in operated air pump is also included. The push-buttons TEST and CORRECTION are arranged to perform the test in a simple and quick system. CM 0185 Manual Air Content Meter, 1 lt Capacity CM 0186 Motorised Air Content Meter, 1 lt Capacity, with an electric mini-compressor to keep the air pressure constant 47 Geotechnical Testing Equipment Cement Equipment Cement Compression and Flexural Cement Compression and Flexural Machine Standards: EN 196-1, 196-3, 413-2, 459-2, ASTM C305 Standards: EN 196-1, 196-3, 413-2, 459-2, ASTM C305 The Cement Compression and Flexural Machine 25/250 KN is Fully Automatic and has been designed for testing the compression on the 50x50x50 mm cube moulds, 40x40mm and the flexural on the 40.1x40 x160 mm prism moulds according to the related standards. The machine consist of very rigid two column frame with double test chamber, automatic closed loop controlled hydraulic power pack and LCD graphic digital control and readout unit. Very silent power pack can load a specimen between 1 kN/sec to 20 kN/sec. On the dual stage pump high delivery low pressure pump is used for rapid approach and low delivery high pressure radial piston pump is used for test execution. On both frame the load is measured by load cell to get accurate test results. The machine is supplied with safety doors and can test samples up to 250KN. The LCD graphics data acquisition and controls system is designed to control the machine and processing of data from load cells. The digital graphic display allows real time load vs time graph. At the end of the test cycle, the results can be stored in memory (up to 250 test results) or downloaded to a PC using the software format. On all power packs maximum pressure valve is used to avoid machine overloading. CM 0187 Semi Automatic Digital Cement Compression and Flexural Machine 25/250KN CM 0188 Full Automatic Digital Cement Compression and Flexural Machine 25/250KN CM 0189 Semi Automatic Digital Cement Compression 250KN CM 0190 Full Automatic Digital Cement Compression 250KN 48 Accessories: CM 0191 Compression Jig Assembly for EN 196-1 CM 0192 Compression Jig Assembly for ASTM C109 CM 0193 Flexure Jig Assembly for EN 196-1 CM 0194 Flexure Jig Assembly for ASTM C109 www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 49 asphalt equipment production Asphalt is a sticky, black and highly viscous liquid or semi-solid that is present in most crude petroleum. It is most commonly used in road construction. The material consists essentially of two ingredients, aggregate and bitumen which is the binder. A number of technologies allow this simple mix to have an almost infinite number of mixtures which may either be specified or designed to suit a particular engineering requirement. It is therefore important that equipment and test methods are used to determine the different physical and chemical properties of any given asphalt mix. Such parameters include binder content, binder percentage, aggregate grading, void content, resilient modulus, indirect tensile fatigue cracking, creep, softening point, flash and fire point, water content, loss in mass, elongation, elasticity, viscosity and adhesion. 51 Geotechnical Testing Equipment Reflux Extractor Asphalt Equipment Asphalt Mixer Standards: ASTM D2172, AASHTO T164 Standards: EN 12697-35, BS 598-107 The Reflux Extractor is used for the determination of quantitative amount of bitumen in hot-mixed paving mixtures and pavement samples. The Asphalt Mixer is designed for mixing Asphalt samples that can be used for mechanical tests as for example compaction, indirect tensile, Marshall etc. The bituminous mix must be prepared at prescribed temperature for this reason the mixer can equipped with thermostatically controlled heater. The mixing head rotates in the 11 different speed positions from 10 to 240 r.p.m. and the beater from 20 to 480 r.p.m. The user can choose speeds easily by using switch fitted to the machine. The Reflux Extractor is available in two sizes, 1000 gr and 4000 gr capacity models. The apparatus comprises of a cylindrical glass jar, two wire mesh cones with interlocking frames, a water condenser with inlet/outlet tubes and hot plate. AS 0101 Reflux Extractor 1000 gr complete AS 0102 Reflux Extractor 4000 gr complete AS 0103 Filter Paper for the 1000 gr model (pack of 50) AS 0104 Filter Paper for the 4000 gr model (pack of 50) AS 0105 Replacement glass for the 1000 gr AS 0106 Replacement glass for the 4000 gr Standards: EN 12697-1, ASTM D2172, AASHTO T164A Comprises: A removable precision-machined rotor bowl housed in a cylindrical aluminium box. It is driven by an electric motor fitted with AC drive (inverter) with the double function of speed control up to 3600 r.p.m. regardless of the frequency (50 or 60 Hz) and electrical braking. The rotating unit is suspended on the base by four calibrated springs, which assure a perfect stability all over the test. The cover is precisely machined and fitted with solvent resistant gasket to avoid leakages. 52 Spares: AS 0117 Stainless Steel Bowl 5 ltr AS 0118 Stainless Steel Bowl 10 ltr AS 0119 Stainless Steel Beater for the 5 ltr AS 0120 Stainless Steel Beater for the 10 ltr Asphalt Mixer with seperate controller Centrifuge Extractor The centrifuge extractor is used for the determination of bitumen percentage in bituminous mixtures. AS 0115 Asphalt Mixer 5 ltr complete with all accessories AS 0116 Asphalt Mixer 10 ltr complete with all accessories AS 0107 Centrifuge Extractor 1500 gr AS 0108 Centrifuge Extractor 3000 gr AS 0109 Filter Paper for 1500 gr (pack of 100) AS 0110 Filter Paper for 3000 gr (pack of 100) Spares: AS 0111 Replacement Bowl, 1500 g AS 0112 Replacement Bowl, 3000 g AS 0113 Replacement Gasket for 1500 g AS 0114 Replacement Gasket for 3000 g Standards: EN 12697-35, BS 598-107 This Asphalt mixer is designed for mixing of samples and can be controlled externaly using switch key. The mixing head rotates in the speed of 62 and 125 r.p.m. and the beater 140 and 285 r.p.m. Spares: AS 0122 Stainless Steel Bowl 5 ltr AS 0123 Stainless Steel Beater for the 5 ltr AS 0121 Asphalt Mixer 5 ltr complete with all accessories Isomantle Heater The Isomantle Heater is Used to heat the mixing bowl of (5 litres cap.) and (10 litres cap.) mixer. It is fitted with an electronic temperature regulator and can be easily fitted to the mixer under the bowl. Max. temperature 180 °C AS 0124 Isomantle Heater 5 litres cap AS 0125 Isomantle Heater 10 Litres cap www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 53 Geotechnical Testing Equipment Manual Marshall Compaction Asphalt Equipment Marshall Stability Machine Standards: ASTM D1559, D5581, BS 598-107, EN 12697-30 Standards: EN 12697-12, EN 12697-23, EN 12697-34 The Manual Marshall Hammer Assembly is used to compact Marshall specimens manually. The Marshall Stability Machine is used to determine the load and flow values of bituminous mixtures. Comprises: The assembly consists of Compaction Hammer, Compaction Pedestal, Hammer Guide and Compaction Mould Holder. AS 0126 Manual Marshall Compactor complete with all accessories Accessories and Spares: AS 0127 Compaction Hammer, BS 598 AS 0128 Compaction Pedestal, BS 598 comprising a 300 mm sq x 25 mm thick steel plate AS 0129 Compaction Pedestal comprising a 12 inch square x 1 inch thick steel plate, ASTM AS 0130 Steel Block 100 mm diameter x 50 mm height. For heating the compaction hammer foot according to BS 598-107 AS 0131 Paper Discs. 99 mm diameter pack of 100 AS 0132 Replacement glass for the 1000 gr Compaction Mould See AS 0145 Automatic Marshall Compactor Standards: EN 12697-10, 12697-30, BS 598-107 The Automatic Compactor is made of a rugged construction to withstand work. It provides a consistent and even degree of compaction. The Compactor comprises of a compaction pedestal, automatic control system, secure base of 300 mm square x 25 mm thick steel plate. After setting the required number of blows the Automatic Compactor lifts the 4535 g ±20 g hammer and releases it at the desired height of 457mm ±3mm. AS 0133 Automatic Compactor Compaction Mould See AS 0145 Paper Discs see AS 0131 Steel Block See AS 0130 The Marshall is composed by a robust and compact two-column frame with adjustable upper cross beam driven by an electromechanical ram with a maximum capacity of 50 kN and a data acquisition and processing system. The Marshall Stability Machine can be hand operated by a lateral hand wheel for calibration purposes. The mechanical jack raises the lower crossbeam at a constant speed of 50.8 mm/min. The limit switches are provided for the both, bottom and top limit of travel. The Automatic measuring system consists of a 50 kN capacity strain gauge load cell is fitted to the upper cross beam to read stability values and 25 mm x 0.001 mm displacement transducer fitted to the Breaking Head. The Automatic measuring system consists of a 50 kN capacity strain gauge load cell is fitted to the upper cross beam to read stability values and 25 mm x 0.001 mm displacement transducer fitted to the Breaking Head. The Manual measuring system consists of a 50 KN capacity load ring and dial gauge graduated 0.01 mm with 25 mm travel. AS 0134 Marshall Stability Machine complete with all accessories AS 0135 Breaking Head 100 mm AS 0136 Breaking Head 150 mm AS 0137 Load Ring assembly complete with dia gauge, 50 KN AS 0138 S-type Load Cell 50 KN AS 0139 Flow Transducer AS 0140 Data Acquisition and Control System AS 0141 RS232 cable and PC Software AS 0142 Dial gauge graduated 0.01 mm with 25 mm travel with stem brake unit and flow meter pedestal, BS/EN AS 0143 Dial gauge graduated 0.001 inches with 1 inch travel with stem brake unit and flow meter pedestal, ASTM AS 0144 Indirect tensile assembly 100 mm The Manual measuring system consists of a 50 KN capacity load ring and dial gauge graduated 0.01 mm with 25 mm travel. The Marshall Stability Machine can be hand operated by a lateral hand wheel for calibration purposes. The mechanical jack raises the lower crossbeam at a constant speed of 50.8 mm/min. The control system comprises of operating light, start / stop switch and a reading counter used to set the desired number of blows. The limit switches are provided for the both, bottom and top limit of travel. 54 www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 55 Asphalt Equipment Geotechnical Testing Equipment Compaction Mould Compaction Mould, Comprising of Base Plate, Mould Body and Collar. AS 0145 Compaction Mould Manual Bitumen Penetrometer Binder Recovery Apparatus Standards: BS 598-102, BS 5284, EN 12697-1 Standards: EN 1426, BS 2000-49, ASTM D5, AASHTO T 49 The Binder Recovery Apparatus comprises of a thermostatically controlled stainless steel heated water bath (with integral shelf), vacuum pump with regulator, gauge and manifold all mounted a sturdy base with anti-vibration rubberised feet. This double sample unit is supplied complete with rubber hose, bungs, two flasks and a set of polyproylene spheres to aid insulation and reduce the risk to the operator from splashes of hot water. Individual ball valves allow the use of a single sample flask if required. The Penetrometer is used to determine the penetration of bituminous samples under constant load, time and heat. The Penetrometers are intended for measuring the consistency of bituminous materials. Penetration readings are quickly taken from a measuring precision gauge. AS 0147 Binder Recovery Apparatus Universal Sample Extruder Standards: EN 12697-1 ASTM D2172, AASHTO T164A Hubbard-Carmick Specific Gravity Bottles Standards: ASTM D140 AASHTO T40 The Bacon Sampler is to obtain samples or sedimentation from the bottom of a container. The plunger keeps the sampler closed until it strikes bottom, then the sampler opens and fills. The plunger closes again when the bomb is withdrawn, forming a tight seal. Samples can also be obtained from any depth by attaching a cord to the top of the plunger, raising it will to fill the sampler and lowering it to close the sampler. AS 0150 Bacon Sampler, 237 ml capacity The Universal Sample extruder is designed to easily extrude samples from Marshall moulds. It has 30kN capacity and supplied complete with manual hydraulic jack. The extruder can be also used for CBR and Proctor moulds with suitable adaptors. AS 0146 Universal Sample extruder The Hubbard-Carmick Specific Gravity Bottles used with viscous fluids, semi-solid bitumen and emulsions. Made of Borosilicate Glass they come in two shapes. AS 0148 Hubbard-Carmick Specific Gravity Bottle conical 25 ml AS 0149 Hubbard-Carmick Specific Gravity Bottle normal 24 ml 56 Bacon Sampler Comprises: The Penetrometer consists of cast iron base with leveling screws, digital penetration measurement gauge 0.01 mm precision Release button - Automatic zeroing. Needle, transfer dish and penetration moulds. AS 0151 Manual Penetrometer complete with all accessories Accessories: AS 0152 Penetration Needle, hardened steel verification certificate. For testing to BS 2000-49 and ASTM D5 AS 0153 Penetration Needle (unverified) AS 0154 Penetration Tin for penetrations between 200 and 350 AS 0155 Penetration Tin for penetrations below 200 Semi Automatic Bitumen Penetrometer Standards: EN 1426, BS 2000-49, ASTM D5, AASHTO T 49 The Semi Automatic and Full automatic Penetrometer gives you better control when used to determine the penetration of bituminous samples. It comes with build in digital controler and readout unit. During the test, depth penetration is permanently displayed both in units and tenth of units (0.01 mm). An optoelectronic detection of depth penetration with an automated approach and a levelling system for conductive samples are available. AS 0156 Semi Automatic Penetrometer complete with all accessoriesr AS 0157 Full Automatic Penetrometer complete with all accessories AS 0158 Transfer Dish AS 0159 Weight 50 gr www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 57 Geotechnical Testing Equipment Softening Point (Ring and Ball) Apparatus Asphalt Equipment Digital Automatic Cleveland, Flash and Fire Point, Open Cup Standards: ASTM D2172, AASHTO T164 Standards: ASTM D92, DIN 51376 ISO 2592 The Ring and Ball method of determine the softening point bituminous materials. The softening point is considered to be the temperature of the fluid when the ball penetrates the specimen and touches the lower plate. This test method covers the determination of the softening point of bitumen in the range from 30 to 157°C (86 to 315°F) immersed in distilled water (30 to 80°C), USP glycerin (above 80 to 157°C), or ethylene glycol (30 to 110°C) The Digital Automatic Cleveland test Flash and Fire Point on Bituminous products, gas oils, fuel oils, lubrificants. Suitable for flash and fire point detection on different substances and waste materials, having a flash point over 79°C. The sample is warmed up according the methods. When the sample reaches the selected test temperature, the flame is passed automatically above the sample. AS 0160 Softening Point (Ring and Ball) Apparatus complete with all accessories AS 0161 Rings with collars, pack of 2 AS 0162 Thermometer ASTM 15°C IP 60°C AS 0163 Thermometer ASTM 16°C IP 61°C AS 0164 Balls, pack of 50 AS 0165 Pyrex Glass Jar, 85x130mm dia. Comprises: The Ring and Ball Apparatus comprises hotplate with magnetic stirrer, 2 steel balls, ball centering guide, 2 rings, glass vessel and thermometer. Manual Cleveland, Flash and Fire Point, Open Cup Standards: ASTM D92, DIN 51376 ISO 2592 When the flash point is reached, the detection is done by an ionisation detector. For fire point detection, the sample continues to be heated until permanent flame is detected by the second probe, then the auto extinguisher will be placed on the top of the test cup. Measuring Parameters - Temperatures: in °C - Measuring range: +79°C … +400°C - Resolution: 0.06 °C - Accuracy: ± 0.1 °C The Software is Windows Based (Windows 2000, XP, Vista) and is able to manage up to 10 analytical heads simultaneously. - User friendly interface - All analytical parameters recoded - Customisable analysis parameters and methods - Customizable results report - Printable graphs and results AS 0174 Digital Automatic Cleveland, Flash and Fire Point complete Digital Abel Flash Point Standards: EN 924 EN 13736, IP 170 IP 491 IP 492 ISO 1516 ISO 3679 ISO 13736 The Cleveland test method describes the determination of the flash and fire point of petroleum products such as bituminous material with flash points above 79°C (175°F) and below 400°C (752°F) AS 0166 Cleveland, Flash and Fire Point complete AS 0167 Semi Automatic Cleveland, Flash and Fire Point complete Electrically heated by electronic regulator, mounted on a case painted with anti-acid epoxidic products. Accessories: AS 0168 Gas Cylinder Empty, 3kg AS 0169 Gas Reducer AS 0170 Rubber Tube Joint and Tube, 5 meter AS 0171 Thermometer ASTM 11°C IP 28°C Spares: AS 0172 Gas Ignition Device,Pack of 3 AS 0173 Calibrated Brass Cup Calibrated brass cup, gas ignition device fitted with a pivot manually passing through the cup. Fitted with pincers for thermometer. The Semiautomatic type is controlled by digital timer. 58 The Digital Abel Flash Point test method determines the closed cup flash point fo petrolium products such as Bitumen and other liquids havin flash point between -30°C and 71°C inclusive. Electrically heated by electronic regulator, mounted on a case painted with antiacid epoxidis products. Calibrated brass crucible, cover with gas ignition device allowing to ignite the testing sample by a manual glideopening. Motor stirrer, air bath and water bath are made croniumplated cooper. Digital thermometer with thermocouple. With internal cooling coil. AS 0175 Digital Abel Flash Point complete AS 0176 Low Temperature Thermostatic Bath and Circulator up to -45°C AS 0177 Gas Cylinder Empty, 3 kg AS 0178 Gas Reducer 30 mbar AS 0179 Rubber Tube Joint and Tube, 5 meter AS 0180 Thermometer IP74°C AS 0181 Thermometer IP75°C AS 0182 Thermometer IP2°C www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 59 Geotechnical Testing Equipment Digital Automatic Abel Flash Point Standards: EN 924 EN 13736, IP 170 IP 491 IP 492 ISO 1516 ISO 3679 ISO 13736 The Adel Flash point is used on petroleum products having a flash point between -18°C and 71°C (kerosene and solvents). Suitable for flash point detection on different substances such as bitumen and other solvents. The sample is warmed up according to the methods. Asphalt Equipment Loss on Heating Oven (TFOT) Standards: EN 12607-2, EN 13303, BS 2000-45, 460-2, ASTM D6, D1754, AASHTO T47, T179 internal support (on request) rotating at 5-6rpm controlled by a geared motor located on the oven top, digital thermoregulator PID with overtemperature alam and probe, double wall locking door with toughned glass window. If the flash point is reached, the detection is done by an ionisation detector. If not, the shutter closes again and the sample continues to warm up until the next test temperature. AS 0183 Digital Automatic Abel Flash Point complete When the sample reaches the selected test temperature, the shutter is opened and the ignition system introduces itself automatically. Distillation of Cut-Back Asphaltic (Bituminous) Product Standards: ASTM D 402 Gas-heated, 500ml side arm distillation flask, Ø117mm chimney with insulated metal shield, insulated cover split in two halves, Ø100mm lamp screen, two sheets of 16 mesh gauze, 100ml cylinder lamp, empty tube glass cooler, nozzle extensor made in glass, 500ml ball. Supported on a height adjustable platform. AS 0184 Gas Distillation of Cut back Asphaltic Apparatus Dean and Stark Apparatus Standards: ASTM D95 The Dean and Stark Apparatus 3 places test method covers the determination of water in the range from 0 to 25 % volume in petroleum products, tars, and other bituminous materials by the distillation method. Mantle heater with steel rod and clamp, 500ml flask, condeser and graduated 10ml receiver. 60 AS 0185 Dean and Stark Apparatus complete AS 0186 Flask, 500ml, tapered joint 24/40, pack of 3 The Loss on Heat Oven test method is used for determining the loss in mass, the effect of heat and air on a film of semisolid bituminous materials. Completely made from stainless steel, natural ventilation, AS 0187 Loss on Heat Oven AS 0188 Rotating Shelf Accessories: AS 0189 Brass Sample container ASTM D6 AS 0190 Stainless Steel Sample container D1754 AS 0191 Support ASTM D1754 AS 0192 Thermometer ASTM 13°C IP 47°C Rolling Thin Film Oven (RTFO) Standards: BS 2000, EN 12607-1, ASTM D2872 The Rolling Thin Film Oven provides simulated short term aged asphalt binder for physical property testing. Asphalt binder is exposed to elevated temperatures to simulate manufacturing and placement aging. It also provides a quantitative measure of the volatiles lost during the aging process. Completely made from stainless steel, forced ventilation, aluminium carriage rotating at 15rpm - circular and vertical - with 8 places for glass containers, internal fan controlled by a 1,725rpm motor, copper coil with nozzle preheating the air, flowmeter with regulator valve, digital thermoregulator PID with overtemperature alrm and probe, double wall locking door with toughned glass window. AS 0193 Rolling Thin Film Oven Accessories: AS 0194 Glass Sample Containers AS 0195 Thermometer ASTM 13°C IP 47°C AS 0196 Drive belt, pack of 2 www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 61 Asphalt Equipment Geotechnical Testing Equipment Ductility Testing Machine Digital Viscometer Bath Standards: EN 13398, EN 13589, ASTM D113, AASHTO T51 Standards: ASTM D445, D446, D341, D2270 The Ductility Testing Machine used for determining the ductility of bituminous materials by measuring the elongation of briquette mould with molten bitumen in it whic is pulled apart at a specified speed and at a specified temperature. Unless otherwise specified, the test shall be made at a temperature of 77 + 0.9°F (25 + 0.5°C) and with a speed of 5 cm/min + 5.0%. AS 0197 Ductility Testing Machine AS 0198 Refrigerated Ductilometer ASTM D113 AS 0199 Refrigerated Ductilometer EN 13589 EN 13398 AS 0200 Ductility Briquette Mould, ASTM AS 0201 Ductility Briquette Mould, EN 13589 AS 0202 Ductility Briquette Mould, EN 13398 AS 0203 Mould Storage Emulsified Asphalts Apparatus Standards: ASTM D244, D6997 The Emulsified Asphalt test methods and practices cover the examination of asphalt emulsions composed principally of a semisolid or liquid asphaltic base, water, and an emulsifying agent. Aluminium alloy boiler with annular gas lamp for heating, connection glass tube with protection shield, glass condenser for water circulation, 100ml graduated cylinder, supporting ring, bases with rods, pliers. 62 AS 0204 Emulsified Asphalt Apparatus AS 0205 Thermometer ASTM 7°C pack of 2 Three-place stainless steel structure with a 1.500mm stroke, transmission of 10 revolutions on squarethread traction rod, 5cm/min speed, ¼ Hp one-phase geared motor, stainless steel tank with white bottom, insulated walls, armoured stainless steel heater controlled by a digital thermoregulator with overtemperature alarm and probe, cooling coil, traction brass carriage holding moulds, circulation pump for stirring the liquids. The Digital Viscometer Bath is used for measuring oils viscosity by Cannon-Fenske, Ubbelohde and similar capillary. AS 0206 Digital Viscometer Bath, 5 places AS 0207 Digital Viscometer Bath, 7 places Working temperature from ambient to 150°C ±0.1°. Borosilicate tank, cover with 5 holes 50.8mm, stainless steel control box on the cover. Digital thermoregulator PID with overtemperature alarm and probe, cooling coil for improved control near to ambient temperature, stainless steel heater, motor stirrer, with stand-by stainless steel covers, protection Lexan jacket. Accessories: AS 0208 Viscometer Holders for Cannon Fenske, for transparent liquids, pack of 5 AS 0209 Viscometer Holders for Cannon Fenske, for opaque liquids, pack of 5 AS 0210 Viscometer Holders For Ubbelohde, pack of 5 AS 0211 Syringe Metallic Large Digital Viscometer Bath Standards: ASTM D445, D446, D341, D2270 The Large Digital Viscometer Bath Structure is made of stainless steel, cover with 5 holes or 7 holes, 50.8mm, temperature control by digital thermoregulator PID stability ±0.02°C and display resolution 0.01°, adjustable high and low temperature cut-out, low level liquid alarm, cooling coil, stand-by stainless steel covers, light. AS 0212 Large Digital Viscometer Bath, 5 places AS 0213 Large Digital Viscometer Bath, 7 places Accessories: AS 0214 Silicone Oil Kinematic viscosity 50 mm2/s at 25°C, -50 to +300°C, pack of 25 litres AS 0215 Viscosity Charts ASTM D341, D2270 pack of 50 www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 63 Geotechnical Testing Equipment Percentage Refusal Density (PRD) Digital Saybolt Viscometer Standards: ASTM D88 E102, AASHTO T72 The Digital Saybolt Viscometer a device used to measure the viscosity of a fluid such as asphalt. Calibrated brass oil cup with stainless steel flowing orifice, polished and calibrated 1.76mm dia Universal and 3.15mm dia Furol. Digital thermoregulator PID with overtemperature alarm and PT 100A probe, stirrer, cooling coil, 18/8 stainless steel water bath, insulated double wall and front opened jacket. Monitoring the time required for the flow of specific volume to fill a 60cc container flask. The time recorded in seconds at three different temperatures. It has 2 sample testing capacity with digital display. AS 0216 Digital Saybolt Viscometer, 2 places AS 0217 Digital Saybolt Viscometer, 3 places AS 0218 Digital Saybolt Viscometer, 4 places AS 0219 Saybolt Viscosity Flask 60 ml AS 0220 Set of Glass Thermometers 6 pcs AS 0221 Filter funnel With stainless steel wire mesh Rice Test Vibrator Apparatus Standards: ASTM D2041 The Rice Test Vibrators provide consistent shaking of vacuum pycnometers. Comes with vibrating rate control and timer. Easy to allow quick placement and removal of Pyknometer. Asphalt Equipment AS 0222 Rice Test Vibrator Apparatus Standards: BS 598-104, EN 12697-32, 13280-4 The Percentage Refusal Density is the ratio of the initial dried density of the sample to the final density (refusal density) expressed in percentage. The sample bulk density is obtained by weighing in air and water; it is then heated in a split mould and compacted to refusal using a vibrating hammer. The final density is then determined by weighing in air and water. AS 0226 Percentage Refusal Density complete with accessories AS 0227 Split Mould and Baseplate AS 0228 Vibrating Hammer AS 0229 Small Tamping Foot 102 mm dia AS 0230 Large Tamping Foot 146 mm Dia AS 0231 300mm Shank, For Tamping foot Rate of Spread Balance Standards: BS 598-108, EN 12272-1 The Rate of Spread Balance determine the spread of coated chippings. This is determined using the calibrated spring balance and the rate of spread of tray. Comprises: Rate of Spread Tray, manufactured from aluminium, 300mm square complete with four chains and lifting eye attached to a spring balance. The spring load balance will accept rates of spread between 4 and 16kg/m². AS 0232 Spring Balance AS 0233 Tray and Four Chains Vialit Plate, Adhesion Test Apparatus Standards: EN 12272-3 Vacuum Pyknometer, 6000 g Standards: ASTM D2041, AASHTO T209, T283 The Vacuum Pyknometer is a 10 ltr, 6000 gr capacity unit used in the Rice Test to determine the maximum specific gravity of bituminous. A transparent cover for easy observation of sample testing, perforated plastic shelf, water inlet valve and tube, quick disconnect, 64 vacuum hose and aspirator with fitting The Vialit Plate Adhesion Apparatus is designed to assess the adhesion property of aggregates to bitumen. AS 0223 Vacuum Pyknometer, 6000 g AS 0224 Vacuum Pyknometer Set AS 0225 Residual-pressure Manometer The apparatus consists of a metal basement with three vertical pointed rods to hold the test plate; vertical rod 50 cm high with a shot at the upper end for the steel ball to drop; a 512 g steel ball; 6 metal test plates, hand operated rubber lined roller with lead shots ballast. AS 0234 Vialit Plate www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 65 Geotechnical Testing Equipment Benkelman Beam Apparatus Rolling Straightedge Apparatus Standards: AASHTO T256 Standards: AASHTO T256 The Benkelman Beam Apparatus is designed to determine the deflection of a flexible pavement or road surface under moving wheel loads. Comprises: The equipment is light weight and made of aluminium for easy portability and use at any test location, the length of the Benkelman beam is 250cm and net weigh is 15 kg. Asphalt Equipment One end of the beam rests at a point under investigation while the beam is pivoted in the centre. The free end carries a dial gauge to record the deflections while the other end is kept on a stable platform. AS 0235 Benkelman Beam Apparatus complete with all accessories Traveling Beam Device Standards: EN 1426, BS 2000-49, ASTM D5, AASHTO T 49 The Travelling Beam Device is used for detecting surface irregularities in both concrete and asphalt pavement. Comprises: The apparatus comprises of a 3-meter length beam with rigid wheels at the extremes and the middle, which can detect any vertical deviation of the surface from a straight-line between the two wheels at the ends of the machine. Measuring capacity of the device is ±25 mm with 5mm increments. It comprises manual dye marker which can mark irregular surfaces of the road. AS 0236 Traveling Beam Device complete AS 0237 Autographic Recorder. AS 0238 Charts for Autographic Recorder. Pack of 10 rolls AS 0239 Fibre-tipped Pen 66 The Rolling Straightedge measures depressions on the pavement surface on analogue scale 0-12mm + 0.25mm. The straightedge also has an odometer for accurate determination of distance travelled in units of 1 metre. The national specifications for surface regularity are then compared and the pavement accepted or rejected and or remedial work undertaken. AS 0240 Rolling Straightedge Apparatus The Rolling Straightedge is pushed at 1-2km/h and the number of irregularities, their length and distance from start, are recorded. www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 67 concrete equipment production Concrete is used more than any other man-made material in the world, it is a composite construction material composed of cement (commonly Portland cement), coarse aggregates, sand, water and chemical admixtures. The word concrete comes from the Latin word “concretus” (meaning compact or condensed) hence, concrete solidifies and hardens after mixing with water and placement due to a chemical process known as hydration. The water reacts with the cement, which bonds the other components together, eventually creating a robust stone-like material that can be moulded in any shape we desire. The quality of concrete is important if structures formed from this versatile material are to be safe and serve the purpose for which they were constructed therefore, several tests are conducted to identify the characteristics and parameters of concrete. The testing equipment described in this section are special selected to test the physical parameters of concrete for consistency, degree of compaction, workability, setting time, segregation resistance, confined flowability, air content, bulk density, specific gravity, adhesion, water permeability and strength. 69 Concrete Equipment Geotechnical Testing Equipment Vebe Consistometer Slump Test Standards: EN 12350–2, BS 1881: 102, ASTM C143, AASHTO T119 Standards: EN 12350-3, ASTM C1170 The Slump test method is used for the determination of the consistency, medium and high workability of fresh concrete. Comprises: The set comprises of slump cone, slump cone funnel, 600 mm long x 16 mm diameter tamping rod which is hemispherical at both ends, base plate, rubber mallet and steel rule. Supplied either galvanized or paint coated to prevent corrosion. The vebe test is a variation of the simple slump test where the concrete is subject to vibration after removal from the slump cone to determine the workability of fresh concrete. CN 0101 Slump test set complete Spares: CN 0102 Slump Cone Funnel CN 0103 Base Plate CN 0104 Rubber Mallet CN 0105 Tamping Rod CN 0106 Steel Rule A plastic disc is placed into contact with the upper surface of the concrete, the vibrating table underneath operates at a fixed amplitude allowing the lower surface of the disc to be completely coated with cement. Comprises: Vibrating table Slump cone Graduated rod and transparent plate Filling cone and tamping rod. CN 0109 Vebe Consistometer Spares: CN 0110 Filling Cone CN 0111 Slump Cone Flow Table Standards: EN 12350-5, BS 1881-105 Waltz Container Standards: EN 12350-4 Waltz Container is used for determining the degree of compactability and consistency of fresh concrete. Comprises: Comprises of a 200x200x400 mm (w x d x h) metal container with two carrying handles. Coated against corrosion. CN 0107 Waltz Container The Flow Table test is used for determining the consistency and workability of fesh concrete. The conical mold for casting the flow specimen and the caliper for measuring the diameter of the mortar after it has been spread on the flow table. The top table is inscribed and all parts are protected against corrosion. The stainless steel cone has a top of 130 mm dia., base of 200 mm dia., and higheat of 200 mm. Supplied complete with wooden tamping rod. Comprises: The apparatus consists of a double steel table, the upper table measuring 700x700 mm and hinged at one side to the lower table. CN 0112 Flow table K-slump Test Pocket Penetrometer The K-Slump Test is used for in-place measurements of forms and test moulds. The K-slump Tester indicates correlation to the slump Test, The Probe determines the workability of concrete and the degree of compaction after being placed in the forms. 70 CN 0108 K-slump Standards: ASTM C403, AASHTO T197 The Pocket Penetrometer is designed for determination of setting time of fresh concrete for field and laboratory use. Stainless steel plunger 32.3 mm² (1/20 inch²) area; plunger graduated 0-5 MPa. CN 0113 Pocket Penetrometer www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 71 Geotechnical Testing Equipment Setting-time by Concrete Penetrometer Concrete Equipment L Shape Box Standards: ASTM C403, AASHTO T197 The Concrete Penetrometer is used for determination of setting time of the mortar fraction of fresh concrete. Comprises: The Concrete Penetrometer consists of a spring loading device which is graduated from 2 to 150 lbs, Set of stainless steel needle points of 650, 325, 160, 65, 32, and 16 mm² area. CN 0114 Concrete Pentrometer complete Spares: CN 0115 Set of needle Points The L Shape Box is used for evaluation of self compactability (confined flowability) of freshly mixed self compacting concrete. CN 0118 L Shape Box apparatus complete The box gives the opportunity to evaluate different properties, such as filling ability, passing ability and resistance to segregation. Compacting Factor Apparatus V-Funnel Apparatus The V-Funnel apparatus is used to evaluate the segregation resistance of freshly mixed self compacting concrete by observing the flowing speed due to the difference of samples remaining period in the funnel. Standards: BS 1881-103, BS 5075 Comprises: The test set consists of a stainless steel funnel placed vertically on a supporting stand. The discharge orifice is equipped with a lid, which can be momentarily opened. The Apparatus enables a check to be made on the weight of concrete when it is falls from fixed heights into a cylindrical container of standard capacity. Comprises: The Apparatus consists of two conical hoppers each with a hinged trap with quick release mechanism to allow free flow of the concrete sample. A cylindrical mould is fitted beneath the hoppers. CN 0119 Compacting Factor Apparatus CN 0116 V-Funnel apparatus complete Air Entrainment Meter Standards: EN 12350–7, ASTM C231, AASHTO T152 U Shape Box Apparatus The U Shape Box is used to determine the confined flowability and the capacity of SCC concrete to flow within confined spaces. Comprises: The Box is made of galvanized steel frame consisting of four 10 mm diameter and three 13 mm diameter bars. CN 0117 U Shape Box apparatus complete 72 The Air Entrainment Meter is used to determine air content of fresh concrete. The meter measures up to 22% entrained air with an accuracy of ±0.25% at full scale. It is appropriate for aggregates size of maximum 50mm. CN 0120 Air Entrainment Meter, Short Type CN 0121 Air Entrainment Meter, Long Type Comprises: It consists of a flanged 7 liter capacity cylindrical vessel and cover assembly incorporating a pressure gauge air pump and valves. The instrument can be calibrated and it is supplied complete with straight edge and tamping rod. www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 73 Concrete Equipment Geotechnical Testing Equipment Vibrating Poker Bulk Density Measures Standards: BS 812, EN 1097-3, 12350-6, ASTM C29, C138 Standards: EN 12390–2, 12350-6, -7, ASTM C31, C192, AASHTO T 23, T126 The Bulk Density Measures is used to determine the loose bulk density and voids of Compacted Fresh Concrete. Manufactured from heavy gauge steel these bulk density measures comply with the requirements of either BS/EN or ASTM C138. All measures has a carrying handles as per the required standard. The Vibrating Poker is 25mm Tip, 250mm long ideal for the internal compaction of concrete specimens and a good alternative to traditional tamping bar especially when there are large numbers of specimens to be compacted. CN 0122 Bulk Density 3 ltr CN 0123 Bulk Density 7 ltr CN 0124 Bulk Density 10 ltr Melting Pot CN 0125 Bulk Density 15 ltr CN 0126 Bulk Density 20 ltr Density of Hard Concrete, Specific Gravity Frame Standards: EN 12390-7, 1097-6, BS 1881:114 The Apparatus is used for specific gravity determination of fresh and hardened concrete. Comprises: A purpose built robust frame designed to support the electronic balance. The lower part of the frame incorporates a moving platform, which carries the water tank allowing the test specimens to be weighed in both air and water. CN 0128 Specific Gravity Frame supplied complete with water tank, Buoyancy Balance, Cradle and suspension hook Spares: CN 0129 Cradle and suspension hook CN 0130 Water Tank CN 0131 Buoyancy Balance, 15 kg x 0.5 g 74 CN 0132 Vibrating Poker complete CN 0127 Bulk Density 30 ltr Standards: EN 12390-7, 1097-6, BS 1881:114 The Melting Pot is used for melting capping compound (sulphur). Comprises: The apparatus consists of a aliminium container in a well-lagged steel jacket, cover and thermostatic control heating system to keep the temperature constant. Specify Temp: - 60° to 250°C, 100° to 320°C - 60° to 450°C, 150° to 550°C CN 0133 Melting Pot 1/2 litre CN 0134 Melting Pot 1 litre CN 0135 Melting Pot 2.5 litre CN 0136 Melting Pot 4.5 litre CN 0137 Melting Pot 9 litres Cylinder Capping Frame Standards: ASTM C617, EN 12390-3 AASHTO T23 The Cylinder Capping Frame is used to assure plane end surfaces perpendicular to the axis of the cylinder during the capping. Built to last the frame comprising vertical supports mounted on a steel base.which can be disassembles for easy machining. SN 0138 Cylinder Capping Frame SN 0139 Cylinder Specimens, 75mm SN 0140 Cylinder Specimens, 100mm SN 0141 Cylinder Specimens, 150mm SN 0142 Flake Capping Compound, 22 kg bag www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 75 Concrete Equipment Geotechnical Testing Equipment Planetary Concrete Pan Mixer J-Ring Apparatus Standards: ASTM C 1621/C 1621M-06 Standards: BS 1377:2, ENV 1997-2, ASTM D4318, AASHTO T89 The Planetary Concrete Pan Mixer is efficient for mixing concrete samples for laboratory. It is designed to give efficient mixing of both dry and wet materials, It Mixture with vertical axis. Reduction gear epicyclical. Manual discharge mouth, on the bottom. Manual charge of raw material. Inertial counter-rotating satellite. Axle with idle wheels and rudder bar. The Cylinder capacity can be either 130, 220 or 300 Litres and the Yeld for mixture is 220 litres. The Tank ring-shaped made by plate with big thickness. The mixerhas 3 shovel, external and internal scraper plus satellite inertial rotating arm. The mixer head lifts clear to provide maximum access to the pan and holds the mixing blades at a constant depth during the mixing operation. The blades can be adjusted to suit the different types and volume of materials to be mixed. CN 0143 Planetary Concrete Pan Mixer, 130 lt CN 0144 Planetary Concrete Pan Mixer, 220 lt CN 0145 Planetary Concrete Pan Mixer, 300 lt 76 The J-Ring test, in conjunction with the Slump-Flow test, is one way to determine the passing ability of SCC, defined as the ability of the concrete to flow under its own weight to completely fill all spaces within the formwork. The J Ring Test Set includes the J-Ring assembly, Modified Slump Cone, high-density polyethylene Strike-Off Bar and a plastic Base Plate with convenient cut-out carrying handles. CN 0146 J Ring Test Set complete CN 0147 J Ring CN 0148 Slump Cone CN 0149 Strike-Off Barone Pull Off Strength Apparatus Standards: ASTM C4541, ACI 503-30, BS 1881-207 The Pull-off Tester determines strength of concrete overlay adhesion and the strength of applied coatings, such as plastics, mortars, plasters, bituminous coats. The Pull-off Tester tests at any measuring point, without requiring specimen preparation. It has a crank drive, with adjustable legs optimize measurements for the specific test situation. Comprises: digital force gauge with lbf, PSI, kN and N/mm2 selectable display units, 50 mm diameter test disc, tensile draw bolt, carrying case and instruction manual. CN 0150 Pull off Strength Apparatus CN 0151 50mm Test Disks, set of 10 CN 0152 Steel Replacement Draw Bolt www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 77 Concrete Equipment Geotechnical Testing Equipment Concrete Cube Moulds Pan Concrete Mixer Standards: EN 12390-1-2, ASTM C39, 192, AASHTO T23, T126 The Pan Concrete Mixer is efficient for mixing quality concrete. Pan type mixer is suitable for the mixing concrete in the laboratory. It is designed to give efficient mixing of both dry and wet materials. The total effective capacity of the mixer is 56 ltr. The Cast iron, hard plastic or steel cube moulds are manufactured in accordance to dimensions and tolerances stated in the related standards. Comprises: The mixer head lifts clear to provide maximum access to the pan and holds the mixing blades at a constant depth during the mixing operation. The blades can be adjusted to suit the different types and volume of materials to be mixed. Cast Iron Cube Moulds: Two part or Four part with clamp attached base plate cast ironand steel moulds are designed to be durable, resistant and easy to clean. CN 0158 Cube moulds 100 mm,4 Part with Clamp base plate CN 0159 Cube moulds 150 mm,4 Part with Clamp base plate CN 0160 Cube moulds 200 mm,4 Part with Clamp base plate CN 0161 Cube moulds 100 mm,2 Part with Clamp base plate CN 0162 Cube moulds 150 mm,2 Part with Clamp base plate CN 0163 Cube moulds 200 mm,2 Part with Clamp base plate CN 0153 Pan Concrete Mixer Drum Concrete Mixer The Drum Concrete Mixer is used for efficient mixing of concrete. The 125 ltr capacity Heavyduty mixer is equipped with rubber wheels which provide high portability. CN 0154 Drum Concrete Mixer, 125lt CN 0155 Drum Concrete Mixer, 170lt 78 CN 0156 Drum Concrete Mixer, 350lt CN 0164 Steel Cube moulds 100 mm, with Clamp base plate CN 0165 Steel Cube moulds 150 mm, with Clamp base plate CN 0166 Steel Cube moulds 200 mm, with Clamp base plate Plastic Cube Moulds: CN 0167 Plastic Cube moulds 100 mm CN 0168 Plastic Cube moulds 150 mm CN 0169 Plastic Cube moulds 200 mm Plastic Cube Moulds with handle: CN 0170 Plastic Cube moulds 100 mm with handle CN 0171 Plastic Cube moulds 150 mm with handle CN 0172 Plastic Cube moulds 200 mm with handle CN 0157 Drum Concrete Mixer, 425lt www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 79 Geotechnical Testing Equipment Concrete Cylinder Moulds Concrete Equipment Concrete Beam Moulds Standards: EN 12390-1-2, ASTM C39, 192 Standards: EN 12390-1-2, ASTM C39, 192, AASHTO T23, T126 The Cast Iron Cylinder Moulds are manufactured in accordance to dimensions and tolerances stated in the related standards. Steel beam moulds are manufactured in accordance to dimensions and tolerances stated in the related standards. Two part and clamp attached base plate steel moulds are designed to be durable, resistant and easy to clean. We also offer Heavy Duty Plastic beam moulds which are much lighter and build to last long time. Cast Iron Cube Moulds: CN 0173 Cast Iron Cylinder Moulds, Split type 100x200 mm CN 0174 Cast Iron Cylinder Moulds, Split type 150x150mm CN 0175 Cast Iron Cylinder Moulds, Split Type 150x300mm CN 0176 Cast Iron Cylinder Moulds, Ring Type 100x200 mm CN 0177 Cast Iron Cylinder Moulds, Ring Type 150x150mm CN 0178 Cast Iron Cylinder Moulds, Ring Type 150x300mm The Plastic Cylinder Moulds are manufactured in accordance to dimensions and tolerances stated in the related standards. Plastic Cube Moulds: CN 0179 Plastic Cylinder Moulds 100x200 mm CN 0180 Plastic Cylinder Moulds 150x150mm CN 0181 Plastic Cylinder Moulds 150x300mm 80 CN 0182 Beam mould 100x100x500 mm CN 0183 Beam mould 150x150x600 mm CN 0184 Beam mould 150x150x750 mm CN 0185 Pastic Beam mould 100x100x500 mm CN 0186 Plastic Beam mould 150x150x600 mm CN 0187 Plastic Beam mould 150x150x750 mm Curing Tank Standards: EN 12390-1-2, ASTM C39, 192 The Curing Tank is designed for curing concrete cubes, beams and cylinders. The temperature can be set and maintained to the required value by an electric resistance incorporating a thermo regulator which maintains set temperature between ambient and 40ºC with ±2ºC accuracy. The tank is also supplied with a submersible circulator pump to assure good temperature uniformity. CN 0188 Small Curing Tank complete with all accessories CN 0189 Large Curing Tank complete with all accessories CN 0190 Set of Racks for Small Curing tank CN 0191 Set of Racks for Large Curing tank CN 0192 Recirculating Pump and heater www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 81 Concrete Equipment Geotechnical Testing Equipment Crack Detection Microscope Vibrating Table Standards: EN 12390–2 The Crack Detection Microscope is a precision apparatus, used for measuring cracks in concrete. It has its own adjustable light source for darkened conditions. The image is focused by turning a knurled knob on the side and the eyepiece scale can be rotated through 360 degrees to align with the crack under examination. The Vibrating Table is a compact unit providing controlled vibro-compaction with fixed amplitude in the laboratory using cube or cylinder moulding equipment. Comprises: Vibrating tables consists of vibrating motor,control unit and clamping assembly. The table is available in two alternative sizes, 610 x 380 mm and 1260 x 620 mm. Small table accepts 4, large table accepts 8 cube, cylinder moulds or beam moulds by using clamping assembly. CN 0193 Large Vibrating Table 1260 x 620 mm Standards: BS 1881-203, EN 12504-4;ASTM C597 CN 0194 Small Vibrating Table 610 x 380 mm An essential tool for investigating the structural integrity of a wide range of materials. This new generation Concrete Ultrasonic can be used in the laboratory or on site to investigate uniformity; cavities, cracks, fire/frost damage, delamination, deterioration and strength. It has memory storage of up to 100 sets of readings and built in RS232 serial port for download of data. Supplied with a simple software download utility kit and does not require Standards: EN 12390-8 82 CN 0197 Crack Detection Microscope complete Concrete Ultrasonic Non-destructive Apparatus Concrete Impermeability Apparatus The Concrete Impermeability Apparatus is used for the determining of the depth of penetration of water to hardened concrete specimens under pressure. 3 and 6 specimen capacity models are available. The system can test 150x150x150 mm, 200x200x200 mm cube or 150x300mm cylinder specimens. Pressure to the sample, up to 10 bar with 0,2 bar precision is generated by way of compressed air applied to the integral water tank and controlled by a pressure regulator; with a pressure gauge. The penetration of water is measured through the burettes supplied complete with the system. The system comprises impermeability gaskets for every cell. The apparatus has to be fitted with the suitable air compressor with maximum working pressure of 10 bar. The 4mm range of measurement is divided into 0.02mm divisions. reference bar as calibration is done by ‘zeroing’. It can calculate and display additional parameters – velocity, path length and Young’s Modulus. It can be set to any pulse repetition frequency from 1 to 100 and has pulse delay mode which allows the user to take readings at specified intervals from 1 per second up to 99 hours. CN 0198 Concrete Ultrasonic Non-destructive Apparatus Mechanical Strain Gauge Standards: BS 1881-206 The mechanical strain gauge allows strain measurement to be made at different parts of a structure using a single instrument. comes with a digital gauge. CN 0195 Impermeability Three Place Model Complete CN 0196 Impermeability Six Place Model Complete CN 0199 StrainGauge 100mm CN 0200 StrainGauge 200mm www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 83 Geotechnical Testing Equipment Concrete Test Hammer Digital Concrete Test Hammer Standards: EN 12504-2, ASTM C805, BS 1881 The Concrete Test Hammer is the traditional instrument used for the non-destructive testing of hardened concrete. This easy-to-use instrument provides a quick and simple test for obtaining an immediate indication of concrete strength in various parts of a structure. The verifiable strength is between 10 and 70 N/mm² The test anvil on the other hand is used to verify test hammer calibration. the calibration must be verified before and after a test sequence. CN 0201 Concrete Test Hammer, Normal Type complete with carrying case,PSI curve and carborundum stone CN 0202 Testing Anvil with surface hardness > 62 HRC Our latest generation concrete test hammer is made of the best components, distinctive ergonomic and all this brought to the development of the special type of concrete hammers with higher degree of reliability as far as correlation curves are concerned, obtaining the new SonReb method. To develop new curves, 50 cubic samples (200x200mm) of twenty distinct classes of concrete have been tested. The verifiable strength is between 10 and 120 N/mm2 84 Concrete Equipment Comprises: - Instruction manual with MpA - PSI curves - Notepad to record index values - Pencil - Abrasive grindstone complete with case - Position template (length 25 mm) - Position template (length 30 mm) - Phenolphthalein atomizer - Phenolphthalein label precautions - Padded case with shoulder-strap - Notepad for recording scale values - Calibration and QC certificate - Transport safety cap Standards: EN 12504-2, ASTM C805, BS 1881 Our Digital Concrete Test Hammer is full of Precision and Reliability of the latest generation, the distinctive ergonomic design, the quality of the material used. Light weighted and as easy to handle as a mechanical sclerometer, the Digital Concrete Hammer is an essential tool for the field experts. By means of a built-in operating system menu, the Digital Hammer can perform simple concrete tests while constantly recording the collected data. Testing parameters settings according to the required standards. A dedicated data card, which enables to acquire, store and analyze the collected data, allows to download them on to a PC to be further processed. Comprises: - Model: Digital Concrete Test Hammer, type N - Battery life: 60 hours - Impact energy: 2,207 Nm - Operating temperature -10 ºC +65 ºC - Measurement range 10-120 N/mm2 - Dimensions: 330x80x100 mm - Internal memory 20,000 index values - LCD graphic display 64x124 - Controls: icons keyboard - Interface: RS232 - Power supply, 5 rechargeable batteries LR6 1.5V CN 0204 Digital Concrete Test Hammer complete with all accessories Micro Covermeter Standards: BS1881 part 204 The Micro Covermeter is developed model with newly designed probe believed to incorporate the most accurate depth and bar size determination routines available. Combined with extremely good resolution of multiple bars, sets the unit apart from others and sets the benchmark for covermeter surveying. CN 0205 Micro Covermeter complete CN 0203 Concrete Test Hammer, Special Type complete with all accessories www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 85 Concrete Equipment Geotechnical Testing Equipment Compression Machine Compression Machine Standards: EN 12390-3,4,5,6; EN 12504-1, 1354, 1521, 13161, 1338, 1340, 196, 772-1, -6, 13286-41, BS 1881 3892-3, 187, 6073-1, 6717 ASTM C39 Our range of 2000 kN and 3000KN capacity Compression Machines has been designed to meet the need for reliable and consistent testing of concrete samples. The machines feature both model the semi automatic and the Full automatic models. The Full automatic models comes with complete automatic test cycle, a closed loop digital readout unit. Once the specimen parameters have been introduced, it is sufficient to press the START button to complete the test. Standards: EN 12390-3,4,5,6; EN 12504-1, 1354, 1521, 13161, 1338, 1340, 196, 772-1, -6, 13286-41, BS 1881 3892-3, 187, 6073-1, 6717 ASTM C39 The Full Automatic Compression Machines consist of their main parts: Frame, power pack and data acquisition control system. CN 0206 Full Automatic Compression machine, 2000 KN CN 0207 Full Automatic Compression machine, 3000 KN Accessories: CN 0208 Distance Piece 20 mm CN 0209 Distance Piece 30 mm CN 0210 Distance Piece 50mm CN 0211 Distance Piece 90mm CN 0212 Distance Piece 100mm The dual stage power pack which is controlled by the control system which is designed to supply the required oil to the frame. Very silent power pack can load a specimen between 1 kN/ sec to 20 kN/sec. On the dual stage pump high delivery low pressure pump is used for rapid approach and low delivery high pressure radial piston pump is used for test execution. On all power packs maximum pressure valve is used to avoid machine overloading. 86 LCD graphics data acquisition and controls system is designed to control the machine and processing of data from load cells or pressure transducers installed on the compression machine frame. Dedicated software package is available for further online data processing, database management and certificate printing. The easy to read LCD graphic display and touch-button data pad keys make the unit quick and straight forward to operate. All interactions with the measuring system are via the front control panel by using simple menu-driven procedures. www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 87 Concrete Equipment Geotechnical Testing Equipment Block Test Platens Compression Machine Standards: EN 12390-3,4,5,6; EN 12504-1, 1354, 1521, 13161, 1338, 1340, 196, 772-1, -6, 13286-41, BS 1881 3892-3, 187, 6073-1, 6717 ASTM C39 The Semi Automatic range of Compression Testing Machine is designed to meet most needs for reliable and consistent testing. The Display Unit is a microcontroller controlled device with advanced facilities for data capture, calculation and presentation. Standards: EN772-1, BS 6073-1 Block Test Platens Sliding Rail Assembly Standards: EN 772-1, BS 6073-1 The Block Test Platens Sliding Rail Assembly 510mmx310mmx50mm allows the platens to be easily installed without removing the existing circular platens. CN 0213 Semi Automatic Compression machine, 2000 KN CN 0214 Semi Automatic Compression machine, 3000 KN CM 0216 Block Test Platens Sliding Rail Assembly Accessories: Distance Pieces, See Page Splitting Tensile Devise and Compressometer The Block Test Platens 510mmx310mmx50mm are used for testing concrete blocks and other structural materials. CN 0215 Block Test Platens 88 Standards: EN 1338, EN 12390-6, ASTM C 496 The Splitting Tensile Devise for testing samples 320 mm long x 200mm wide and 40 mm to 130 mm thick. Specialy designed Splitting Jig that is used for Splitting Concrete Blocks, Cylindrical Speciments and Concrete Cubes of different sizes. The Cylinder Splitting Jig for testing cylinders of 150 x 150 mm and 150 x 300 mm (diameter x length). CM 0217 Block Splitting Jig www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 CM 0218 Cylinder Splitting Jig CM 0219 Cubes Splitting Jig CM 0220 Compressometer 89 Concrete Equipment Geotechnical Testing Equipment Compression Machine Flexural Test Machine Standards: EN 12390-3,4,5,6; EN 12504-1, 1354, 1521, 13161, 1338, 1340, 196, 772-1, -6, 13286-41, BS 1881 3892-3, 187, 6073-1, 6717 ASTM C39 EN 12390-5,6, 1338, 1340, ASTM C78, C293, C496 The Flexural Testing Machine range of 100 kN and 200 kN capacity have been designed for reliable and consistent testing of concrete beams, transverse test on kerbs and flagstones, indirect tensile tests on concrete and interlocking pavers. The Flexural Test assembly on Concrete Beams is used for 3 or 4 point flexural tests on 100 or 150 mm concrete beams. The distance of the lower bearers can be adjusted between 100mm and 800mm. The distance between upper bearers can be set to 100mm or 150 mm. During the 3 point Flexural testing one of the bearers can be removed and the other placed in the center. The bearer dimensions are 40mm diameter x 160 mm length. The Flexural Machines feature the complete automatic test cycle with a closed loop digital readout. Once the specimen parameter have been introduced, it is sufficient to press the START button to complete the test. CN 0225 Bearers for concerete beams of 100x100x400-500 mm, 150x150x600-750 mm. Consist of two upper rollers and two lower rollers of. 40 dia. and 160 mm lenght. Complying to EN 12390-5 and ASTM C78 The Flexural Frame can be connected to any Geotechnical compression machine as a second frame. CN 0221 Flexural Testing Machine, 100 kN capacity CN 0222 Flexural Testing Machine, 200 kN capacity The Flexural Test assembly for Kerbs and Blocks consists of two lower bearers 20mm diameter x 600mm long and 40 mm diameter upper loading piston with ball seating assembly. The distance between lower bearers can be adjusted from 100mm to 800mm. Comprises: The Flexural machines consist of their main part frame, power pack and data acquisition & control system. Each part has been designed to manufacture machines with a high degree of mechanical stability and complies with the suitable standard. CN 0223 Bearers for flexure test on flagstones and kerbs to EN 1339 and 1340. Consist of two lower roller of 20 mm dia. x 600 mm lenght and upper load point of 40 mm dia with ball seating CN 0224 Bearers for flexure test on concrete blocks Consist of two lower roller and one upper roller of 20 mm dia. x 600 mm lenght 90 www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 91 Geotechnical Testing Equipment Concrete Equipment Rapid Chloride Permeability Pipe Testing Machine Standards: EN 12390-5,6, 1338, 1340, ASTM C78, C293, C496 Standards: ASTM C1202, AASHTO T-277 The Automatic Pipe Test Machine is a 1000KN static application for tensile, compression and bending tests of concrete pipes. The machine can test pipes both verticaly and horizontaly each according to the installation and accessories used. It can test large building pipes, joists, plates,sections of various shapes and sizes. It is often necessary to evaluate chloride permeability characteristics of concrete in bridges and other structures. Now the electronic technology is available to evaluate slices of cores taken from such sources using a 6-hr. laboratory procedure. By testing slices from laboratory cylinders, the method is also suitable for evaluation of materials and/or additives for mix design of HPC or other concretes. CN 0226 Automatic Pipe Test Machine Compression and Tension Testing Machine Standards: BS 1610, ASTM C-39, E4 AASHTO T-22, ASTM C78, C293, C496 The Compression and Tension Automatic Testing Machine has a range of 500 kN tension and 1000 kN compression capacity. It is designed to meet the need for reliable and consistent testing of steel rebars and concrete samples for use both in the field and laboratory. The machine consists of a very rigid frame with double-acting cylinder assembly to perform tension tests on steel rebars up to 22 mm dia., flat specimens up to 15mm thick and 50mm wide, compression tests on concrete cubes up to 150 mm and on cylinders up to 160x320 mm. Its Heavy Duty, high degree of accuracy and low cost make this machine ideal for site testing and educational purposes. CN 0227 Compression and Tension Testing Machine Current flow with time is measured while a 4” (102mm) diameter, 2” (51mm) thick specimen slice is subjected to a regulated 60V DC potential across ends. The negative end is exposed to 3% sodium chloride solution, and the positive end to 0.3N sodium hydroxide solution. The Rapid Chloride Permeability test Instrument automates the integration of current relative to time to determine coulombs as a measure of chloride permeability. supply capability of 30 to 60 volts DC. Instrument cabinets measure 19x17x7” (432x483x178mm), WxHxD. Order the Test Cells separately, minimum of 4 needed. Vacuum Apparatus, required for either systems, includes vacuum pump, electronic vacuum gauge, water trap, desiccators, stand, clamps, filter paper, and vacuum hose. CM 0228 Rapid Chloride Permeability Apparatus complete set 4 cell model CM 0229 Rapid Chloride Permeability Apparatus complete set 8 cell model Accessories: CM 0230 Chloride Permeability Vacuum complete set CM 0231 Rapid Chloride Permeability Test Cell, Pair Models are available to test four, or eight specimens simultaneously. Test voltage, test time, current for each specimen and coulombs for each specimen are continuously displayed. Printouts of the above data are automatically activated every 30 minutes or at a different user selectable rate. The printout can also be manually activated at any time by switch and are directed to the internal printer. Tests are automatically terminated at 360 minutes. Current range is 0-1 amp DC per core. The Rapid Chloride Permeability Units have a wide range voltage 92 www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 93 aggregate equipment production Aggregate is a component of a composite material used to resist compressive stress and provide bulk to the composite material. For efficient filling, aggregate should be much smaller than the finished item, but have a wide variety of sizes. It is vastly used in most combination of construction material such as concrete and asphalt technology to which aggregates may either be specified or designed to suit a particular engineering requirement while not suiting another. The properties of aggregates can vary and hence affect the final construction material. Therefore it is important to test the different parameters such as resistance to polishing, particle size, shape and texture, relative, bulk density, crushing value, impact value, organic impurities, compacted densities, specific gravity, soundness and abrasion resistance. 95 Aggregate Equipment Geotechnical Testing Equipment Shape Index Gauge Flakiness Sieves Standards: BS 812 Flakiness Sieves are used to determine particle size shape or geometrical characteristics of the aggregates. Each sieve made from heavy gauge steel sheets in dimensions specified in the standards and coated with electrostatic paint. Grid Sieves Standards: EN 933-1, EN 933-3 Grid Sieves are used to determine the flakiness index of the aggregates. Made of electrostatic steel frame and 5 mm diameter stainless steel parallel bars. Standards: EN 933-4 Product Code AG 0101 AG 0102 AG 0103 AG 0104 AG 0105 AG 0106 AG 0107 Slot Size 4,9 mm slot size 7.2 mm slot size 10.2 mm slot size 14.4 mm slot size 19.7 mm slot size 26.3 mm slot size 33.9 mm slot size Product Code AG 0108 AG 0109 AG 0110 AG 0111 AG 0112 AG 0113 AG 0114 AG 0115 AG 0116 AG 0117 AG 0118 AG 0119 AG 0120 Aperture (mm) 2,5 mm 3.15 mm 4 mm 5 mm 6.30 mm 8 mm 10 mm 12.5 mm 16 mm 20 mm 25 mm 31.5 mm 40 mm Shape Index Gauge is used to determine the shape factor of individual aggregates by comparing the ration of length to width. AG 0123 Shape Index Gauge Particle Density (specific gravity) and Water Absorption Sand Absorption Cone and Tamping Rod Standards: EN 1097-6, 12697-6, BS 812, ASTM C127-C128, AASHTO T85, T84 The Sand Absorption Cone and Tamping Rod are used to determine the specific gravity and absorption of fine aggregates smaller than 20 mm. AG 0124 Sand Absorption Cone and Tamping Rod complete set The Apparatus is manufactured from plated steel for protection against corrosion. AG 0125 Sand Absorption Cone AG 0126 Tamping Rod Spares: Specific Gravity Frame and Buoyancy Balance Standards: BS 812, ASTM C127, AASHTO T85 BS 812, ASTM C127 AASHTO T85 EN 1097-6, 12697-6, EN 12390-7 Flakiness Gauge EN 1097-6, 12697-6, EN 12390-7 Standards: BS 812 Flakiness Gauge is used to determine if aggregate particles are to be considered flaky, i.e. their thickness is less than 0.6 of their nominal size. AG 0121 Flakiness Gauge 96 Length Gauge classifies aggregate elongation by measuring the length of individual particles. Aggregate particles are considered elongated when their length is more than 1.8 of their nominal size. Length Gauge test is not applicable to material retained on 63.0 mm BS test sieve. AG 0122 Length Gauge This method is used to determine the aggregates specific gravity. The robust frame is designed to support the buoyancy balance. The lower part of the frame incorporates a moving platform, which carries the water tank allowing the test specimens to be weighed in both air and water. AG 0127 Specific Gravity Frame supplied complete with water tank, Buoyancy Balance, Wire Basket and suspension hook Spares: AG 0128 Wire Basket and suspension hook AG 0129 Water Tank AG 0130 Buoyancy Balance, 6000 g x 0.1 g www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 97 Aggregate Equipment Geotechnical Testing Equipment Bulk Density Measures Aggregate Crushing Value and Ten Percent Fines Value (ACV / TFV) Standards: BS 812-2, 3797, EN 1097-3, 12350-6, ASTM C138, C29 Standards: 812-110, 111 The Bulk Density Measures are used to determine the loose bulk density and voids of aggregates. Aggregate crushing Value provides a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. They are made from heavy steel gauge and specially coated against corrosion. Product Code AG 0131 AG 0132 AG 0133 AG 0134 AG 0135 AG 0136 Capacity Model 3 ltr 7 ltr 10 ltr 15 ltr 20 ltr 30 ltr Chloride and Sulphate Content, Instant Test Strips Quantab chloride titrators can be used for estimating the chloride content of aqueous solutions.They are suitable for site testing and quality control of aggregates requiring less than 30 minutes to obtain a result. AG 0137 Quantab Chloride Titrator Strips.Type 1175 titration range 0.005% to 0.1% (30 to 600 ppm) NaCl. Pack of 50. AG 0138 Quantab Chloride Titrator Strips. Type 1176 titration range 0.05% to 1% (300 to 6000 ppm) NaCl. Pack of 40. A qualitative or semi-quantitative test is recommended for determining sulphate ions in aqueous solutions. Sulphate test strips are convenient measuring devices for preliminary assessment of sulphate content. AG 0139 Sulphate Test Strips detection range 200 to 900 mg/l. Pack of 100. Ten Percent Fines Value used for testing aggregate smaller than 10 mm. Comprises: 150 mm or 75mm diameter steel cylinder, plunger, base plate, tamping rod and metal measure. All parts are powder coated or galvanized. Product Code AG 0144 AG 0145 AG 0146 AG 0147 AG 0148 Description Aggregate Crushing Value Apparatus 150 mm dia. Metal Measure 115 mm diameter x 180 mm deep For Aggregates Smaller Than 10 mm Aggregate Crushing Value Apparatus,75 mm dia. Metal Measure 57 mm diameter x 90 mm deep. Accessories: Tamping Rod 8 mm diameter x 300 mm long Aggregate Impact Value (AIV) Standards: 812-112 Organic Impurities in Fine Aggregate If aggregate contains organic impurities it may not be suitable for inclusion in concrete. Organic impurities, usually tannic acid and its derivatives, may interfere with the chemical reactions of hydration. Impurities are more likely to be found in fine (sand) aggregate. 98 AG 0140 Organic Impurities complete Test Set, containing Graduated Bottle, Reference Color Comparison Chart and Sodium Hydroxide solution AG 0141 Graduated Bottle, 300 ml AG 0142 Reference Color Comparison Chart AG 0143 Sodium Hydroxide Solution The Aggregate Impact Value machine has been developed for determining the impact value of aggregates. Manufactured from plated steel against corrosion, a counter fitted to the machine automatically records the number of blows delivered to the sample. cylindrical measure and steel tamping rod. AG 0149 Aggregate Impact Value apparatus complete The AIV is supplied complete with 75 mm diameter x 50 mm deep . www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 99 Aggregate Equipment Geotechnical Testing Equipment Los Angeles Abrasion Machine Digital Point Load Apparatus Standards: EN 1097-2, ASTM C131, C535 Standards: EN 1997-2, ASTM D-5731 Los Angeles Abrasion Machine is used for determination of aggregates resistance to fragmentation. The point load tester is used to measure rock strength in the field or laboratory. The machine consists of an electronic control unit and a rolled steel drum having an inside diameter of 711 mm and internal length 508 mm. A load frame, hydraulic jack and digital display are mounted on the base of a carrying case. With this point load tester, samples up to 4” (101.6mm) diameter can be tested on 2 conical points. The drum is rotated at a speed of between 31 and 33 r.p.m. The internal shelf is provided with the machine is conforming to ASTM and EN standards. Standards: EN 1097–9 AG 0150 Los Angeles Abrasion Machine 220 V, 50–60 Hz AG 0151 Los Angeles Abrasion Machine with safety cabinet, 220 V, 50–60 Hz Abrasion Testing Machine The abrasion wheel is 70 mm thick and rotates with speed of 75 r.p.m. The machine is equipped with digital counter which stops the rotation at the preset number of revolutions. 100 AG 0152 Set of 11 abrasive charges conforming to EN AG 0153 Set of 12 abrasive charges conforming to ASTM The Nordic Abrasion Machine has been developed to test the resistance to abrasion/wear from studded tires. Test is being performed on natural stones and aggregates between 11,2 mm and 16 mm, it consists of rotating aggregates in drum with steel abrasive balls and water. The machine consists of an electronic control unit and a rolled stainless steel drum having an inside diameter of 206,5mm, internal length 335mm and thickness of 6mm. The drum is rotated at a speed of 90±3 r.p.m. 3 wings are installed inside of the drum to allow balls and aggregates to be mixed properly. The abrasion loss rate of aggregates is calculated after specified number of revolutions stated in the related standard. AG 0156 Nordic Abrasion Machine Accelerated Polishing Machine Standards: EN 1341, 1342, 1343 Abrasion Testing Machine is designed to determine the resistance to abrasion and wear of natural stones and concrete products. AG 0155 Digital Point Load Apparatus Nordic Abrasion Machine The machine is equipped with automatic counter, which allows stopping when the preset number of revolutions is completed. There is a steel tray supplied with machine for easy discharge of specimen. Safety Cabinet model are installed with electronic control unit and electric safety device which automatically stops the rotation of the drum when the door is opened, conforming to CE directives. A graduated scale indicates distance between conical points and is also used to measure specimen diameter. Applied load is digitally displayed to 0.001kN; accuracy is ±1%; range is 0 to 56kN. Display shows maximum load and will also read in lb and tons. Standards: EN 1097-8, EN 1341, 1342, 1343 AG 0154 Abrasion Testing Machine The Accelerated Polishing Machine is used to measure the resistance of road stone to the polishing action of vehicle tires on a road surface. The machine consists of road wheel rotating in the speed of between 315 and 325 r.p.m. The machine is supplied complete with road wheel, side plate, rubber rings, abrasive feed mechanism, corn emery, flour emery, set of 4 specimen mould and 2 mould plates. AG 0157 Accelerated Polishing Machine www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 101 Geotechnical Testing Equipment Skid Resistance and Friction Tester (Skid Tester) AAV Abrasion Machine Standards: EN 1097-8, ASTM E103, BS 812:144 Standards: EN 1097-8, BS 812 The AAV Abrasion Machine provides a measure of the resistance of aggregate to surface wear by abrasion, it consists of a flat circular cast iron grinding lap 600 mm dia which rotates in a horizontal plane at a speed of 28/30 r.p.m. Aggregate Equipment The abrasive sand is fed across the surface of the specimen samples through a special funnel. The machine is supplied complete with two specimen moulds, two trays, two flat plates, weights and clamps. AG 0158 AAV Abrasion Machine The Skid Tester is used for measuring the surface friction properties, it is suitable for both site and laboratory applications and for Polished Stone Value tests using curved specimens from accelerated polishing tests. Supplied complete with additional scale for tests on polished stone value specimens and 6 rubber sliders for site usage. AG 0160 Skid Resistance Tester complete with all accessories AG 0161 Rubber Sliders for site usage AG 0162 Claping device for tests on natural stones AG 0163 Claping device for polish stone value tests AG 0164 Metal base plate High Capacity Screen Shaker Micro-Deval Testing Machine The High Capacity Screen Shaker is ideal for sizing large quantities of crushed stones, sand, gravel, slag, coal, coke, ores, pellets and similar materials. Standards: EN 1097-1 The Micro Deval Testing Machine used to determine the resistance of wear for 25-50mm size aggregates. The machine consists of a steel frame, four stainless steel cylinders, and 25kg of 10 mm diameter stainless steel spheres. Fitted with an automatic digital counter that allows the machine to stop automatically at preset number of revolutions. Stainless steel Ø200 x 154 drums rotates at speed of 100 (±5) r.p.m. AG 0159 Micro-Deval Testing Machine The screen shaker has a capacity of about 30 kg of sample. For use with 457x660x75mm dimension screens. AG 0165 High Capacity Screen Shaker AG 0166 Set of screens Shrinkage and Expansion of Aggregates Standards: BS812-120, EN 1367-4 The scope of this test is the determination of the effect of aggregates on the drying shrinkage of concrete. The test is based on the testing of concretes of fixed mix proportions and aggregates of 20 mm max size. 102 AG 0167 Three gang Prism Mould for specimens 50 x 50 x 200 mm Rest of the accessories are in the cement section www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 103 general equipment production Our general laboratory equipment are complementary equipment that are used in conjunction with our major equipment. We supply an extensive inventory of general laboratory product of the best quality and value ranging from balances and scales, thermometers, laboratory ovens, muffle furnaces, vacuum pumps, air compresors, core drills, laboratory glassware, water baths, pans, bowls, dishes, jars, trowels, brushes, shovels, spatulas and general tools. 105 Geotechnical Testing Equipment Laboratory Ballances and Scales Our range of balances are designed for the lab but have the rugged features needed for materials testing. They include all metal chemical resistant die-cast housings. Compact and durable, these balances are the best choice for basic GN 0101 GN 0102 GN 0103 GN 0104 GN 0105 GN 0106 GN 0107 GN 0108 GN 0109 GN 0110 GN 0111 GN 0112 GN 0113 GN 0114 GN 0115 GN 0116 GN 0117 GN 0118 GN 0119 GN 0120 GN 0121 GN 0122 GN 0123 GN 0124 weighing and economy. The tough durable ABS housing is designed to withstand field and laboratory environments, while being easy to clean and protected from accidental spills. Electronic Digital Balances Digital Balance 250 g 0.0001 g resolution Digital Balance 250 g 0.001 g resolution Digital Balance 450 g 0.001 g resolution Digital Balance 750 g 0.001 g resolution Digital Balance 1500 g 0.01 g resolution Digital Balance 2500 g 0.01 g resolution Digital Balance 4500 g 0.01 g resolution Digital Balance 6000 g 0.1 g resolution Digital Balance 8000 g 0.1 g resolution Digital Balance 10 kg 0.1 g resolution Digital Balance 20 kg 0.1 g resolution Digital Balance 20 kg 1 g resolution Digital Balance 32 kg 1 g resolution Digital Balance 30 kg 5 g resolution Digital Balance 48 kg 2 g resolution Digital Balance 60 kg 5 g resolution Digital Balance 75 kg 1 g resolution Digital Balance 75 kg 5 g resolution Digital Balance 150 kg 10 g resolution Digital Balance 300 kg 20 g resolution Mechanical Scales Harvard Trip Balance 2000 g, 0.1 g readability Triple Beam Balance 2610 g, 0.1 g readability Dial-O-Gram Balance 310 g, 0.1 g readability Heavy Duty Solution Balance 311 g, 0.01 g readability General Equipment Multi-Purpose Drying Ovens Standards: EN 932-5, 1097-5, ASTM C 127- C136-D558, D559, D560, D698, D1557, D1559 BS 1377:1-1924:11 The Geotechnical Laboratory Ovens offer a range of highly efficient, reliable, cost effective units to suit most drying, warming and general laboratory applications. The exterior is constructed from sheet steel finished in an easy clean powder coated paint. The interior chamber is made from mild steel coated with aluminium (CLAD) with a stainless steel chamber available as an option. Fitted with fixed shelf runners and removable chrome plated wire grid shelves. Heated by Incoloy sheathed elements positioned below the chamber floor for natural convection units and fitted around the fan on the back or side wall of the chamber for mechanical convection units. The control system comprises of a Digital thermometer with thermostatically controlled units Microprocessor digital controller. Model No. Capacity (Litres) Number of Shelves Number of Shelves Position Fluctuation Weight (Kg) GN 0125 GN 0126 GN 0127 GN 0128 GN 0129 50 125 225 225 425 40-250C 40-250C 40-250C 40-200C 40-250C 2 3 3 3 4 3 5 4 4 5 0.75 0.75 0.75 0.75 0.75 31 57 80 80 150 GN 0130 GN 0131 425 750 40-200C 40-250C 4 5 5 8 0.75 0.5 150 200 GN 0132 1000 40-250C 6 11 0.5 240 GN 0133 Digital Tempreture control GN 0134 Fan Circulation 106 Temperature GN 0135 Spare Shelve GN 0136 Audible warning alarm www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 GN 0137 Door lock 107 General Equipment Geotechnical Testing Equipment Core Drill Heavy Duty Core Drilling Machine Standards: EN 12697-27 Standards: EN 12697-27 The Portable Core Drill petrol powered engine is used for fast drilling into concrete or asphalt surfaces. It can take up to 180mm core bit diameter capacity, Heavyduty, precision gear box – optimum gear ratio for fast and economical drilling. Power 1.6 HP, Weight 8 Kg. The Heavy Duty Core Drill Machine is designed to minimize time required for cutting cores up to 150 mm diameter from concrete, asphalt and similar hard construction material. This Core Drill is capable of handling large and small hole with stable drilling platform and dependable performance while increasing the bit life. GN 0138 Handheld Core Drill with stand GN 0139 Handheld Core Drill without stand GN 0140 Core Bit, 50 mm dia GN 0141 Core Bit, 100 mm dia GN 0142 Core Bit, 150 mm dia Core and Rock Drill The Compact and latest design in Rock Drill machinery, suitable for working on high mountains and places with no power supply and air compressing equipment, especially suitable for temporary projects. Carried easily as the weight is only 27kg, built up with petrol engine, air pump, rock drill. GN 0143 Rock Drill Heavy-duty, dual-precision ground columns and tenzalloy precision machined carriage assembly Smooth-precision ball feed screw system, accurate hole drilling positioning and easy alignment of drill platform. Demolition Breaker The Demolition breaker is used to break hard concrete surfaces. It has a robust metal housing and large soft padded grips which is easy to use. 2100 watt Motor. GN 0145 Demolition Breaker complete with chisel GN 0146 Concrete Breaker chisel GN 0147 Core Drill with Platform, Petrol Engine 6.0 HP Weight 140Kg, complete with core bit GN 0148 Core Drill with Platform, Petrol Engine 10.5 HP, Weight 160Kg, complete with core bit GN 0149 Core Bit, 50 mm dia GN 0150 Core Bit, 100 mm dia GN 0151 Core Bit, 150 mm dia GN 0144 Rock Drill chisel 108 www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 109 Geotechnical Testing Equipment Masonry Saw General Equipment Water Bath Standards: EN 1367-3 The Masonry Saw is a compact light weight bench saw for cutting small to medium sized building materials for example bricks, blocks, rocks, tiles and slabs. Special clamp assembly allows specimens to be held during cutting operation. GN 0152 Masonry Saw complete with bench, clam and saw blade GN 0153 350mm dia. Blade GN 0154 450mm dia. Blade GN 0155 600mm dia. Blade The Water Bath is ideal for general laboratory use including Marshall tests. Internal surfaces of polished stainless steel and housed in a sheet steel insulated outer case. Thermostatic digital heat controlled baths 0 to 99 ºC supplied complete with cover. GN 0163 Water Bath 12 Ltr GN 0164 Water Bath 20 Ltr GN 0165 Water Bath 30 Ltr GN 0166 Water Bath 48 Ltr Temperature measurement Air Compressor Standards: EN 1367-3 The Air Compressor is easy to use and to control the air manipulation. The Cast Iron cylinder compressor pump is long lasting and with reliable performance. 1.3 HP comes with 25 ltr or 50 ltr capacity. GN 0156 Air Compressor, 25 liters GN 0157 Air Compressor, 50 liters The selection criteria for any thermometer should include: Vacuum Pump The Vacuum Pump is ideal for laboratory use, it removes gas molecules from a sealed volume in order to leave behind a partial vacuum. The free air displacement is 100 Ltr/Min. Ultimate Vacuum is 0.01 (mbar). 220 V, 50-60 Hz, 1 ph GN 0158 Vacuum Pump GN 0159 Rubber Tubing, 1meter 110 ● measurement range ● resolution of the reading 1°C, 0.1°C or 0.01°C ● desired accuracy ● response time Our Thermocouple, thermometers and probes are fast to respond to changes in temperature, they also have a wide measurement range. Resistance temperature detector and more accurate. justifiably proud of the quality of both our products and service. To ensure recognition and maintenance of our quality standards we are registered to BS EN ISO 9001:2000. Original UKAS Certificates can be provided to proof that the instruments and probes have been calibrated against nationally approved standards. Model No. Description Temp Range GN 0167 Digital Pocket Thermometer -50 - +250°C 0.1ºC ±0.4°C GN 0168 Digital probe Thermometer -49.9 to 199.9°C 0.1°C ±0.5°C GN 0169 Digital probe Thermometer -50 to 1000°C 1°C ±1°C GN 0170 Digital probe Thermometer -50 to 1000°C 0.1°C ±0.5°C GN 0171 Thermocouple Wire 1 meter -50 - +250°C 0.1ºC ±0.5°C GN 0172 K type Probe -50 to 1000°C 1°C ±1°C Double Water Distillation Equipment GN 0173 K type Probe -50 - +250°C 0.1ºC ±0.5°C GN 0162 GN 0174 Thermal Data Loger, 4000 Reading -40 to 125°C 0.1°C ±0.5°C Distilled Water Still Equipment The Water Distillation unit gives high quality distilled water having an output of 4 litre/hr with a power input of 3 KW. The unique features along with the safety provisions make it an ideal equipment to obtain pure distilled water for use in general laboratories and in numerous other end uses.. Selecting the correct thermometer for an application is very important, to achieve the maximum accuracy and repeatability of the temperature reading. GN 0160 Single Water Distillation Equipment GN 0161 Spare glass www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 Temp Resolution Accuracy 111 General Equipment Geotechnical Testing Equipment Tempreture, Hygrometer and Hydrometer Measurement General Laboratory Hardware Standards: EN 1367-3 Model No. GN 0175 GN 0176 GN 0177 GN 0178 GN 0179 GN 0180 GN 0181 GN 0182 GN 0183 GN 0184 GN 0185 GN 0186 GN 0187 GN 0188 GN 0189 GN 0190 GN 0191 GN 0192 GN 0193 GN 0194 GN 0195 Description Temp Range Resolution Glass Thermometers Glass Thermometers -10 - +60°C 1.0 ºC ±1°C Glass Thermometers -10 - +110°C 1.0 ºC ±1°C Glass Thermometers -10 - +160°C 1.0 ºC ±1°C Glass Thermometers -10 - +250°C 1.0 ºC ±1°C Glass Thermometers -10 - +310°C 1.0 ºC ±1°C Min-Max Thermometer –20 to +50ºC 1.0 ºC ±1°C Protected Thermometer –15 to +60ºC 1.0 ºC ±1°C Dial Surface Thermometers 0 to 160ºC 1.0 ºC ±1°C Portable Dial Thermometers Portable Dial Thermometers –30 to +60 1.0 ºC ±1°C Portable Dial Thermometers –30 to +250 1.0 ºC ±1°C Portable Dial Thermometers 0 to +250 1.0 ºC ±1°C IP Thermometers IP24C Thermometers +95 +103 0.1ºC ±0.1°C IP28C Thermometers –6 to +400 0.1ºC ±0.1°C IP38C Thermometers 23 to 27 2.0ºC ±0.1°C IP60C Thermometers –2 to +80 0.2ºC ±0.1°C IP61C Thermometers 30 to 200 0.5ºC ±0.1°C IP89C Thermometers –1 to +175 0.5ºC ±0.1°C Hygrometer and Hydrometer Hydrometer, Range 0.995 to 1.030 densities (gms/cc) at 270C Hydrometer, Range 0.995 to 1.030 densities (gms/cc) at 270C Hygrometer, for humidity and temp, -10 to 60°C and 20 to 95% RH Digital Barometer, Range 0 to 1300mbar (0 to 975mmHg) General Laboratory Hardware ModelNo. GN 0196 GN 0197 GN 0198 GN 0199 GN 0200 GN 0201 112 Description Spatulas Spatula, 100 mm blade with wooden handle Spatula, 150 mm blade with wooden handle Spatula, 200 mm blade with wooden handle Trowels Small Trowel Large Trowel Float. Plasterer’s type Model No. Description Sample Trays GN 0202 GN 0203 GN 0204 GN 0205 GN 0206 GN 0207 Sample Tray, galvanised steel, 17 x 27 x 4 cm Sample Tray, galvanised steel, 27 x 46 x 4 cm Sample Tray, galvanised steel, 40 x 40 x 5 cm Sample Tray, galvanised steel, 60 x 60 x 6 cm Sample Tray, galvanised steel, 90 x 90 x 7 cm Sample Tray, galvanised steel, 120 x 120 x 5 cm Sample Container GN 0208 GN 0209 GN 0210 GN 0211 GN 0212 Sample Container. Steel. Lever Lid, 0.5 litres Sample Container. Steel. Lever Lid, 2.5 litres Sample Container. Steel. Lever Lid, 5 litres Sample Container. Steel. Lever Lid, 10 litres Sample Container. Steel. Lever Lid, 15 litres Wire Baskets GN 0213 Wire Basket, BS 812, EN 1367-2 65 mm dia x 80 mm deep Wire Basket, BS 812, EN 1367-2 95 mm dia x 120 mm deep Wire Basket, BS 812, EN 1367-2 120 mm dia x 120 mm deep General Items Accuracy GN 0214 GN 0215 GN 0216 GN 0217 GN 0220 Trimming Knife Heat-resistant Gloves Rubber Gloves Model No. Description Scoop GN 0221 GN 0222 GN 0223 Scoop Large 7 x 11 x 4 cm Scoop Medium 12 x 19 x 7 cm Scoop Small 25 x 31 x 11 cm Beakers and Bowls GN 0224 Bowl. 2 litre capacity, stainless steel GN 0225 GN 0226 GN 0227 GN 0228 GN 0229 Bowl. 6 litre capacity, stainless steel Bowl. 9 litre capacity, stainless steel Beaker. 250 ml capacity, aluminium Beaker. 500 ml capacity, aluminium Beaker. 1000 ml capacity, aluminium www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 113 General Equipment Geotechnical Testing Equipment General Laboratory Accessories Model No. GN 0230 GN 0231 GN 0232 GN 0233 GN 0234 GN 0235 GN 0236 GN 0237 GN 0238 GN 0239 GN 0240 GN 0241 GN 0242 GN 0243 GN 0244 GN 0245 GN 0246 GN 0247 GN 0248 GN 0249 Description Temp Range Resolution Accuracy Lab General Accessories Vernier Calliper, 200 mm 0 to 200mm 0.1mm ±0.1mm Vernier Calliper, 300 mm 0 to 300mm 0.1mm ±0.1mm Digital Vernier Calliper, 0 to 200mm 0.1mm ±0.1mm 200 mm Digital Vernier Calliper, 0 to 300mm 0.1mm ±0.1mm 300 mm Infrared Thermometer –20 1.0 ºC ±1°C to+350ºC Hot Air dryer +150ºC Timer Clock Stop Watch Hot Plates Hot Plate 10cm dia 250 ºC ±1°C Hot Plate 15cm dia 250 ºC ±1°C Hot Plate 20cm dia 250 ºC ±1°C Laboratory Glassware Beaker 50 ml GN 0250 Flask, 50 ml Beaker 100 ml GN 0251 Flask, 100 ml Beaker 250 ml GN 0252 Flask, 250 ml Beaker 500 ml GN 0253 Flask, 500 ml Beaker 1000 ml GN 0254 Flask, 1000 ml Beaker 2000 ml GN 0255 Conical Flask 100 ml GN 0256 Conical Beaker 100 ml Conical Flask 250 ml GN 0257 Conical Beaker 250 ml Conical Flask 500 ml GN 0258 Conical Beaker 500 ml Conical Flask 1000 ml Model No. Description GM 0266 GM 0267 GM 0268 Measuring Cylinders Measuring Cylinder, Plastic 250 ml Measuring Cylinder, Plastic 500 ml Measuring Cylinder, Plastic 1000 ml General Laboratory Hardware Model No. Description GN 0283 GN 0284 GN 0285 Measuring Cylinders Evaporating Dish Ø10 cm Evaporating Dish Ø12 cm Evaporating Dish Ø14 cm Porcelain Crucible 10 ml Porcelain Crucible 15 ml Porcelain Crucible 25 ml Bottles Polythene Bottle, 1 ltr Polythene Bottle, 2.5 ltr Polythene Bottle, 5 ltr Wash Bottle, 500 ml Wash Bottle, 1000 ml General Items Glass Stirring Graduated Pipette, 0.10 ml sub-divisions Graduated Pipette, 0.25 ml sub-divisions Bulb Pipette Bosshead Clamp Straight edge Model No. Description GN 0286 Load Rings Clamp Boss Load Ring 1 KN GN 0287 Clamp Boss Load Ring 2 KN GN 0288 Clamp Boss Load Ring 3 KN GN 0289 Clamp Boss Load Ring 5 KN GN 0290 Clamp Boss Load Ring 10 KN GN 0291 Clamp Boss Load Ring 15 KN GN 0292 Clamp Boss Load Ring 28 KN GN 0293 Clamp Boss Load Ring 50 KN GN 0269 GN 0270 GN 0271 GN 0272 GN 0273 GN 0274 GN 0275 GN 0276 GN 0277 GN 0278 GN 0279 GN 0280 GN 0281 GN 0282 Measuring Cylinders Model No. Description GN 0259 GN 0260 GN 0261 GN 0262 GN 0263 Measuring Cylinders Measuring Cylinder, Glass 50 ml Measuring Cylinder, Glass 100 ml Measuring Cylinder, Glass 250 ml Measuring Cylinder, Glass 500 ml Measuring Cylinder, Glass 1000 ml GN 0264 GN 0265 Measuring Cylinder, Plastic 50 ml Measuring Cylinder, Plastic 100 ml 114 www.geotechnical-equipment.com; t.:+441908 766400/454/452; f.:+441908 520 729 115 appendix index to products Soil equipment Soil Colour Chart, p.04 Soil Sampling Kit, p.04 Power Auger Head, p.04 Water Level Indicators, p.05 Proctor Penetrometer (spring type), p.05 Proving Ring Penetrometer, p.05 Pocket Penetrometer, p.06 Dynamic Cone Penetrometer, p.06 Static Cone Penetrometer, p.06 Pocket Shear Vane, p.07 Dial Penetrometer, p.07 Field Inspection Vane Tester, p.07 Laboratory Vane Apparatus, p.07 Laboratory Mixer, p.08 Isomantle Heater, p.08 Porcelain Mortar and Rubber Head Pestle, p.08 Laboratory Soil Grinder, p.09 Melting Pot, p.09 Sieve Shaker, p.09 Electromagnetic Sieve Shaker, p.10 Testing Sieves, p.10-17 Ultrasonic cleaning bath, p.17 Speedy Moisture Meter, p.18 Universal Carbide Meter, p.18 Liquid Limit Devices: Casagrande Method, p.18 116 Cone Penetrometer Test, p.19 Determination of Plastic Limit, p.19 Determination of Shrinkage Limit, p.19 Linear Shrinkage Mould, p.20 Voluvessel, 1/20 cu. ft. (1600ml) capacity, p.20 Guelph Permeameter Apparatus, p.20 Falling Head Permeameter Apparatus, p.21 Constant Head Permeameter Apparatus, p.21 Gas Jar Method: End-Over-End Shaker, p.22 Mechanical End-over-End Shaker, p.22 Sedimentation Hydrometer Apparatus, p.22 Mechanical Analysis Stirrer, p.23 Pyknometer Methods, p.23 Magnetic Stirrer, p.23 Sand Equivalent Test, p.24 Sand Equivalent Shaker, p.24 Sand Cone Density, p.24 Sand Replacement, p.25 Riffle Boxes, p.25 Gilson Sample Splitter, p.25 Plate Bearing Test Equipment, p.26 Electrical Density Gauge, p.26 Nuclear Density Gauge, p.26 Consolidation Apparatus, p.27 Direct Residual Shear Apparatus, p.28 Automatic Soil Compactor, p.29 Dry Density, Moisture Relationship, Standard and Modified Proctor Mould, p.29 California Bearing Ratio Test Machine, p.30 Data Acquisition and Control System, p.30 Multispeed Test Machine, p.31 In-situ California Bearing Ratio Apparatus, p.31 Expansion Swell Test Equipmen, p.32 CBR Mould and Accessories, p.32 Triaxial Testing Apparatus, p.33 Deaired Water Apparatus, p.34 Air/Water Pressure System, p.34 Oil/Water Pressure System, p.35 Microspear, moisture and temperature, p.35 117