Download BG-C10 User`s Man U al
Transcript
BG-C10 BATTERY GRIP Designed For The Canon EOS 70D SLR Camera Introduction Thank you for choosing Vello and congratulations on your new BG-C10 battery grip purchase. Enjoy the many benefits that a battery grip offers such as extended shooting time and more control and comfort when shooting in a vertical (portrait) orientation. The Vello BG-C10 is compatible with the Canon EOS 70D SLR camera. The BG-C10 accepts two Canon LPE6 rechargeable batteries. Alternatively six AA batteries (alkaline, Ni-MH, lithium, or nickel-manganese) can be used for added convenience. The BG-C10 is equipped with an alternate shutter-release button, AF area selection mode button, AF point selection, AE lock/FE lock button, AF Start, and main dial for shooting in a vertical position. 2 Please read through this entire manual before using the BGC10 battery grip. The BG-C10 should only be used with compatible devices specified in this manual. Remove the batteries and take the device to a Vello authorized reseller. 2. Only use with batteries and battery holders recommended in this manual. 6. Turn 3. Cover the power terminals with the contact cap when the BG-C10 is not in use. This prevents electrical shorts caused by metal objects touching the power terminals. 7. 5. The battery level may not display properly if batteries are inserted before mounting the grip. 8. Remove batteries from the grip when not in use. the battery holder is removed from the grip, remove the batteries or place the holder in a container to prevent electrical shorts caused by contact with other metal objects. 9. If you notice smoke, an unusual smell or noise from the battery pack, discontinue use immediately. 11.Keep out of reach of children. 3 Do not attempt to disassemble. OVERVIEW 4. When the grip power off when not shooting vertically. 10.Avoid water or extreme humidity and keep in a dry and cool place. ASSEMBLY 1. INTRODUCTION Precautions Overview 12 18 16 17 11 10 2 1 9 4 19 15 8 3 7 6 13 5 14 4 3 Attachment Wheel Secures the grip to the camera. 4 Battery Compartment Cover Camera Battery Chamber Cover Holder Stores the camera’s battery chamber cover when the grip is mounted. 15 Main Dial* 16 AF area selection mode button 17 Shutter-Release Button* 18 Tripod Socket 10 Electrical Contacts Communicates with the camera’s electronics. 11 For mounting on a tripod. 5 DC Coupler Cord Mount Groove for use with the Canon AC Power Adapter (ACK-E6). 12 C ontact Cap Protects grip contacts. Keep covered when the grip is not in use. 6 AF Point Selection/Magnify Button* for a secure hold while shooting. 7 AE Lock/FE Lock/Index/Reduce Button* 13 Battery Holder Holds up to two Canon LP-E6 batteries. AA Battery Holder Holder for six AA batteries. camera. Consult your camera’s manual 14 8 AF On Button* INTRODUCTION B G-C10 Grip Power ON/OFF 5 19 Hand Strap Mount Optional hand strap may be mounted OVERVIEW 2 Guide Pin Helps align the camera to the grip. 9 * Performs the same function as on the on the use of these functions. ASSEMBLY 1 Mounting Screw Aligns with the camera’s tripod socket. Attaching The Grip 1. Ensure that the power is turned off on the camera and that the power switch is set to OFF on the battery grip. 2. Remove the battery from the camera battery compartment. 6 3. Open the camera battery chamber cover at a 35º angle and gently pull the cover to remove it. INTRODUCTION A prevent loss, slide the camera battery chamber cover into the BG-C10 battery chamber holder A . To remove the cover, press lightly on the cover hinge B and pull it up at an angle C . 5. Remove the protective cap and connect the BGC10 grip to the camera, while aligning the grip’s mounting screw with the camera’s tripod socket. 7 6. Rotate the attachment wheel in the direction shown by the arrow until it is firmly tightened. When removing the grip, turn the camera power off, remove batteries, and replace protective contact cap. ASSEMBLY 4. To OVERVIEW C B Inserting Batteries A B B B A A C 1. Ensure that the power is turned off on the camera and grip. Pull the lever down A and twist counter-clockwise B to open the battery chamber door. Pull the release lever outward and remove the battery holder C . 2. Canon LP-E6 Batteries: Insert up to two batteries by orienting the arrow on the battery toward the interior of the holder. Press the front of the battery down A and slide forward while pressing on the back of the battery B . 8 3. AA Batteries: Place six new AA batteries of the same type into the AA battery holder as shown, while ensuring that they are in the correct orientation. INTRODUCTION Ensure that camera power is turned off before mounting the DC coupler. Ensure that the DC cord doesn’t get pinched by the battery holder. A the battery holder into the grip, twist the lever clockwise to lock, and flip it up to secure it. 5. Switch the grip power to ON and then turn on the camera’s power. Check the battery level in the control panel or viewfinder. 9 Household Power Outlet: To mount the Canon ACK-E6 AC Power Adapter Kit (sold separately), insert the DC coupler into the side of the handler with the release lever just like a battery. Pass the cord through the groove on the back of the grip. ASSEMBLY 4. Slide OVERVIEW B Specifications Power Source 1. 2. 3. One or two Canon LP-E6 rechargeable Li-ion batteries Six AA/LR6 Alkaline, Ni-MH, Lithium or Nickel-Manganese batteries Works with the Canon AC Adapter Kit (ACK-E6) Operating Temperature 32º – 104° F (0 – 40° C) Dimensions 5.7" × 4.4" × 3.4" (145.6 × 111.3 × 85.3 mm) Weight 10.4 oz. (295g) excluding holder and batteries Specifications and design are subject to change without notice. AA batteries do not provide as much shooting time as LP-E6 rechargeable batteries. Performance of AA batteries may also be dependent on brand and storage conditions. Please note: When using the AA battery tray, the battery indicator will only work with Ni-MH batteries. Please note: When using the AA battery tray, the battery indicator will only work with Ni-MH batteries. This product is not compatible with Duracell® brand alkaline batteries. 10 ONE-YEAR LIMITED WARRANTY This VELLO product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later. The warranty provider’s responsibility with respect to this limited warranty shall be limited solely to repair or replacement, at the provider’s discretion, of any product that fails during normal use of this product in its intended manner and in its intended environment. Inoperability of the product or part(s) shall be determined by the warranty provider. If the product has been discontinued, the warranty provider reserves the right to replace it with a model of equivalent quality and function. This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration, abuse, improper installation or maintenance. EXCEPT AS PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This warranty provides you with specific legal rights, and you may also have additional rights that vary from state to state. To obtain warranty coverage, contact the Vello Customer Service Department to obtain a return merchandise authorization (“RMA”) number, and return the defective product to Vello along with the RMA number and proof of purchase. Shipment of the defective product is at the purchaser’s own risk and expense. For more information or to arrange service, visit www.vellogear.com or call Customer Service at 212-594-2353. Product warranty provided by the Gradus Group. www.gradusgroup.com VELLO is a registered trademark of the Gradus Group. © 2014 Gradus Group LLC. All Rights Reserved. www.vellogear.com © Copyright 2013 Gradus Group LLC All other trademarks are the property of their respective owners