Download User Manual English - Velopex International

Automatic X-Ray Film Processor
Intra - X
USER GUIDE
Operation and
Maintenance manual
WARNING:
Do not plug into the electrical mains power supply before
reading this manual - or before filling the machine with
liquids
Register your machine by returning the Warranty Card
to enable full customer support.
www.velopex.com
C
US
Hi-Tech
Diagnostics
Service
MAKERS OF DENTAL, VETERINARY AND MEDICAL EQUIPMENT
Machine serial number to be
quoted on all correspondence:
I/LIT0040P Intra-X Manual English Iss.6
Issued: 23/04/11
II
Introduction
6ELOPEX0ROCESSOR%XTERIOR
Thank you for purchasing
your automatic film processor from
Velopex - we certainly appreciate your business.
In order to maintain
the quality of our product and your
processing it is important that you pay close attention to the
instructions contained in this user manual. This will ensure a
long life for your processor.
The processor could be dangerous if incorrectly installed
or
maintained outside
the guidelines set out in this manual and the
warranty will be voided.
There are no operator serviceable parts inside the machine .
This equipment can only be serviced by technically qualified
engineers, trained on Velopex machines, and is not designed
to be serviced by the end user other than as specified in this
manual.
6ELOPEX82AY&ILM0ROCESSOR,EFT3IDE
&ILM#OLLECTOR
%NDO3LIDE
/N/FF0OWER3WITCH
(ANDENTRYPORT'LOVE
@2UN3ENSOR
$AYLIGHT,OADER,EFT3IDE
&ILM%NTRY'UIDE
Note: Panel and Label colours and designs may vary.
6IEWER#OVER
Caution: Use assistance when unpacking and putting the
$AYLIGHT,OADERVIEWING7INDOW
machine in place.
4RANSPORT-ODULE
$ISPLAY
-ACHINE!CCESSORIESAND%XTRAS3UPPLIED
Contacts
Office: UK
Office: France
Office: USA
Medivance Instruments Limited
Barretts Green Road, Harlesden
London, NW10 7AP, UK
Tel: +44 (0)20 8965 2913
Fax: +44 (0)20 8963 1270
3ILICONE'REASE
&ILM#OLLECTING4RAY
#LEANING"RUSH
4URNING4OOL
OR
Velopex International
14 route de Montreuil le Gast
B.P.45, 35520 Melesse, France
Tel: +33 (0) 2.99.13.22.59
Fax: +33 (0) 2.99.13.22.60
5+%LECTRICITY3UPPLY#ORD
53!%LECTRICITY3UPPLY#ORD
#ONTINENTAL%LECTRICITY3UPPLY#ORD
OR
Velopex International Inc.
105 East 17th Street, St Cloud
Florida, 34769, USA
Tel: +1 (407) 957 3900
Fax: +1 (407) 957 3927
II
6ELOPEX0ROCESSOR%XTERIOR
Velopex Processor - Exterior
4
2
11
3
1
8
6
7
9
1
2
3
4
7
10
6ELOPEX82AY&ILM0ROCESSOR,EFT3IDE
Velopex X-Ray Film Processor - Left Side
&ILM#OLLECTOR
6IEWER#OVER
Film Collector
Viewer Cover
5
%NDO3LIDE
$AYLIGHT,OADERVIEWING7INDOW
Endo Slide
Daylight Loader viewing Window
6
/N/FF0OWER3WITCH
(ANDENTRYPORT'LOVE
On/Off Power Switch
Hand entry port/Glove
7
@2UN3ENSOR
$AYLIGHT,OADER,EFT3IDE
Daylight Loader - Left Side
8
&ILM%NTRY'UIDE
Film Entry Guide
9
4RANSPORT-ODULE
Transport Module
10
$ISPLAY
Display
11
-ACHINE!CCESSORIESAND%XTRAS3UPPLIED
Machine Accessories and Extras Supplied
12
14
16
22
20
18
15
17
13
23
19
21
12
13
14
15
3ILICONE'REASE
Silicone Grease
&ILM#OLLECTING4RAY
Film Collecting Tray
#LEANING"RUSH
Cleaning Brush
4URNING4OOL
Turning Tool
16 5+%LECTRICITY3UPPLY#ORD
UK - Electricity Supply Cord
20
Quick Start Guide
17 53!%LECTRICITY3UPPLY#ORD
USA - Electricity Supply Cord
21
CD Manual
18 #ONTINENTAL%LECTRICITY3UPPLY#ORD
Continental - Electricity Supply Cord
22
Warranty Registration
23
Cleaning Tablets
ORor
ORor
19
Chemical Change Record Sheet
ii
III
iii
4ABLEOF3YMBOLS
Table
of Symbols
Table Of Symbols
3YMBOL
Symbol
$ESCRIPTION
Description
!LTERNATING#URRENT
Alternating
Current
/FF0OWER$ISCONNECTFROMTHEMAINS
Off
/N0OWER#ONNECTTOTHEMAINS
On
!TTENTION7ARNING2EFERTO-ANUAL
Attention
/ Warning - Refer to Manual
!TTENTION7ARNING(IGH6OLTAGE
Attention
/ Warning - High Voltage
3YMBOLSUSEDWITHIN-ANUAL
Symbols
used within Manual
4IP
Tip
!TTENTION7ARNING
Attention
/ Warning
"LEEP!TTENTION3IGNAL
Bleep
/ Attention Signal
Attention / Biohazard
3PECIlCATIONV
0RE)NSTALLATION)NSTRUCTIONS
)NSTALLATION
$AYLIGHT,OADER)NSTALLATIONIFNOTINSTALLED
&ILLINGWITH#HEMICALS
/PERATION
-AINTENANCE
INSTALLATION
).34!,,!4)/.
OPERATION
/0%2!4)/.
#ONTENTS
Contents
IV
4ROUBLE3HOOTING
23
3ERVICE,OG
©¹
April
2007
-AY-EDIVANCE)NSTRUMENTS,IMITED
!LLRIGHTSRESERVED
)SSUE/-),)4-
MAINTENANCE
TROUBLE SHOOTING
42/5",%3(/54).' -!).4%.!.#%
$ISPLAY%RROR#ODES
V
3PECIlCATION
3PECIlCATION
Specification
(H)
(H)
(H)
(D)
(W)
(D)
(W)
7IDTH7
MM³v
(D)
MMv
$EPTH$
(W)
MMv
)NC,OADER
(EIGHT(
MM³v
7IDTH7
MM³v
7EIGHT%MPTY
+GLB
$EPTH$
MMv
&ULL4ANKS
+GLB
MMv
)NC,OADER
4ANK#APACITY
LITRES³)MP0INTSEACH
MM³v
(EIGHT(
Water
- should not exceed 28˚C&
7ATERSHOULDNOTEXCEED
/PERATING4EMPERATURE
+GLB
7EIGHT%MPTY
(82.4˚F)
#
&ULL4ANKS
+GLB
&
#
25˚C
(77˚F)
$EVELOPER
4ANK#APACITY
LITRES³)MP0INTSEACH
&
#
27.5°C
(81.5°F)
&IXER
7ATERSHOULDNOTEXCEED&
/PERATING4EMPERATURE
/
%LECTRIC3UPPLY
66(Z
#
&#
7ARMUPTIME
MINAPPROX
$EVELOPER
&#
&IXER
&ILM&EED3PEED
MM³vPERMIN
%LECTRIC3UPPLY
66(Z
MM³v
-AXlLMWIDTH
7ARMUPTIME
MINAPPROX
Processing
time*: Dry
0ROCESSINGTIME$RY
MINAPPROX
4.5
min. approx.
7ET%NDODONTIC
MINAPPROX
&ILM&EED3PEED
MM³vPERMIN
)NPUT0OWER
7
-AXlLMWIDTH
MM³v
%NVIRONMENTAL#ONDITIONS
)NDOORUSEONLY
0ROCESSINGTIME$RY
MINAPPROX
0
0 0 7ET%NDODONTIC
%NVIRONMENT4EMPERATURE
&
&F-78.8
#0F)
#
5MINAPPROX
C-26
C (41
)NPUT0OWER
7
-AXIMUM2ELATIVE(UMIDITY
80%
#
5PTO
%NVIRONMENTAL#ONDITIONS
)NDOORUSEONLY
#
# processing
*
in
the
unit’s
first
few
cycles,
timecan
four
#
$ECREASINGLINEARLYTO
%NVIRONMENT4EMPERATURE
&
&vary
#between
and five minutes. Then the process time will stabilise around four
-AXIMUM2ELATIVE(UMIDITY
and a half minutes.
5PTO#
# #
$ECREASINGLINEARLYTO
VELOPEX INTRA-X
User Guide
1
INSTALLATION
Pre-Installation Instructions
• Unpacking the VELOPEX
NOTE: For unpacking and lifting the machine into position it is important to have
assistance.
Check contents of the box, see page ii.
1. Familiarise yourself with the layout of the machine by referring to the images
as you progress through the manual.
2. Lift the machine from the carton and position on counter top. Remove outer
and inner packaging. The transport modules are protected by internal packing
pieces: these must be discarded.
2
VELOPEX INTRA-X
User Guide
Pre-Installation Instructions (Cont.)
INSTALLATION
• Sitting of the VELOPEX
When using the machine in daylight or a darkroom, avoid sources of intense light.
Do not mount the unit under a window, fluorescent light or flood lamp.
IMPORTANT NOTE: A well ventilated position is mandatory.
The ambient temperature must be below 26ºC (78.8ºF).
NB: If the machine has been shipped or stored in excessive heat, allow time for it
to cool to below 26ºC (78.8ºF) before installation. Temperatures above 57ºC will
cause an E14 safety message.
Prevent sitting the machine above or near other electrical or mechanical equipment.
Surfaces susceptible to water or chemical damage should be avoided, such as
carpeted areas.
1. COUNTER
a. Use a stable and level counter that will support a weight of at least 50 Kg
(100lbs).
b. When the machine is filled with chemicals, make sure the stand does not
rock or shake. NEVER move the machine with chemicals in the tanks.
2. ELECTRICAL SUPPLY
a. Refer to specification table, page v.
b. The power source must be within one metre (3 feet) of the machine. It
should be easily accessible for operation and maintenance.
WARNING: X-ray radiation can be harmful to patient, technician and dentist.
Inadequate lead shielding of the darkroom or film storage area will also cause
fogging from exposure of films to stray x-ray radiation. Consult your local
codes, Health Department or Dental Equipment Dealer for proper construction
of darkroom or placement of film processing equipment in the vicinity of x-ray
radiation sources.
NOTE: Pictures are for instruction only and are not necessarily identical to product.
VELOPEX INTRA-X
User Guide
3
1.
2.
Bring the Lid to the upright
position. When
operating,
indication of the opened lid is
displayed as: “Lid”. Unscrew the
retaining screw at the back of
the machine above the plug and
lift the Display Panel.
INSTALLATION
Daylight Loader Installation (if not installed)
Remove Side Panels by sliding
them Upwards in their runners.
6%,/0%8).42!8
5SER'UIDE
/PERATINGTHE0ROCESSOR
3a.
0LUGINELECTRICCORDANDSWITCH
Remove
All Packing / Wrapping
ON4HEMACHINEWILLTHENRUN
Material
and Modules.
THROUGHAHIGHSPEEDSTARTUP
CYCLEOFMINUTES
TIP:
with the Dryer Module,
4)0Start !FTERAPPROXTENMINUTESTHE
then
the Water Module followed by
PROCESSORWILLGOINTO@STANDBYMODE
BYWHICHTIMETHECHEMICALSWILLHAVE
the
Fixer and Developer Modules.
REACHEDTHEIRCORRECTTEMPERATURE
Those
should be removed by sliding
the
tanks out.
7!2.).'
!LWAYSTURN
(Images for instruction ONLY)
)NCORRECTTEMPERATUREISINDICATED
WHENTHEMESSAGEONTHE,%$
DISPLAYREADShT,Ov2EADYTOUSE
%2!4)/.
MAINSELECTRICITYSWITCHOFFATNIGHT
4 /PERATINGTHE0ROCESSOR
VELOPEX INTRA-X
User Guide
3b.
Daylight Loader Installation
0LUGINELECTRICCORDANDSWITCH
ON4HEMACHINEWILLTHENRUN
THROUGHAHIGHSPEEDSTARTUP
(Cont.)
CYCLEOFMINUTES
7!2.).' When removing
!LWAYSTURN
WARNING:
the fixer
MAINSELECTRICITYSWITCHOFFATNIGHT
and
developer modules, slide tanks
sideways until completely clear of the
immersion heaters mounted on the
machine internal wall.
)NCORRECTTEMPERATUREISINDICATED
WHENTHEMESSAGEONTHE,%$
DISPLAYREADShT,Ov2EADYTOUSE
ISINDICATEDBYTHREEHORIZONTAL
Unscrew
the two retaining screws
CENTRALLINESANDCOOLINGDOWNIS
and
remove
white protective strip
INDICATEDINTHELINESDESCENDING
from
sealing
material on the back
FROMLEFTTORIGHT
of4)0
the loader.
Remove black covers
4HETIMETAKENTOACHIEVETHE
from
the
studs
on the front panel.
CORRECTTEMPERATUREDEPENDSONTHE
4.
ROOMTEMPERATUREUSUALLYMIN
)MAGESFORINSTRUCTION/.,9
5.
4HE6ELOPEXISEQUIPPEDWITH
AUTOMATICSTANDBYMODE4O
Remove
protective film from
INITIATEPROCESSINGFEEDlLM
viewing
window cover.
THROUGH%NTRY3LOT)FTHATFAILS
TOWORKSLIDElNGEROVER@25.
3ENSOR
)MAGEFORINSTRUCTION/.,9
6IEWING7INDOWISCLOSEDWHEN
OPERATINGMACHINE
7!2.).'
"EFOREPLACINGIN
THEMACHINEINTRAORALlLMPACKETS
SHOULDBEWIPEDCLEANOFALLMOUTH
CONTAMINANTS
/0%2!4)/.
INSTALLATION
4)0
!FTERAPPROXTENMINUTESTHE
PROCESSORWILLGOINTO@STANDBYMODE
BYWHICHTIMETHECHEMICALSWILLHAVE
REACHEDTHEIRCORRECTTEMPERATURE
VELOPEX INTRA-X
5
6%,/0%8).42!8 User5SER'UIDE
Guide
Slide
Loader over Film Entry
3LIDE,OADEROVER&ILM%NTRY
'[email protected]
Guide.
Press the Loader firmly
THE,OADERlRMLYAGAINST
against
machine.
-ACHINE
)MAGESFORINSTRUCTION/.,9
Secure
Loader with theTwo
two
3ECURE,OADERWITHTHE4HREE
2ETAINING3CREWS2ETURNSIDE
retaining screws. Return side
PANELSLIDPANELANDDISPLAY
panels
and lid panel.
SECUREWITHRETAININGSCREW
Secure
loader with black
knob screwed onto the Stud
now positioned inside the
Loader.
INSTALLATION
).34!,,!4)/.
Daylight
Loader Installation (Cont.)
$AYLIGHT,OADER)NSTALLATIONCONT
6 /PERATINGTHE0ROCESSOR
VELOPEX INTRA-X
User Guide
8.
0LUGINELECTRICCORDANDSWITCH
ON4HEMACHINEWILLTHENRUN
THROUGHAHIGHSPEEDSTARTUP
CYCLEOFMINUTES
Filling with Chemicals
!FTERAPPROXTENMINUTESTHE
/PERATINGTHE0ROCESSOR
9.
0LUGINELECTRICCORDANDSWITCH
)NCORRECTTEMPERATUREISINDICATED
ON4HEMACHINEWILLTHENRUN
WHENTHEMESSAGEONTHE,%$
THROUGHAHIGHSPEEDSTARTUP
DISPLAYREADShT,Ov
2EADYTOUSE
CYCLEOFMINUTES
ISINDICATEDBYTHREEHORIZONTAL
4)0
!FTERAPPROXTENMINUTESTHE
CENTRALLINESANDCOOLINGDOWNIS
Lift
the transport modules from
PROCESSORWILLGOINTO@STANDBYMODE
INDICATEDINTHELINESDESCENDING
their
respective tanks.
BYWHICHTIMETHECHEMICALSWILLHAVE
FROMLEFTTORIGHT
)MAGESFORINSTRUCTION/.,9
REACHEDTHEIRCORRECTTEMPERATURE
4)0
4HETIMETAKENTOACHIEVETHE
WARNING:
filling with
7!2.).' BEFORE
!LWAYSTURN
CORRECTTEMPERATUREDEPENDSONTHE
chemicals
run
the
machine
with clean
MAINSELECTRICITYSWITCHOFFATNIGHT
ROOMTEMPERATUREUSUALLYMIN
water in the Developer, Fixer and
Water Tanks with Transport
Modules in 6%,/0%8).42!8
5SER'UIDE
position for a complete
running
cycle 6%,/0%8).42!8
5SER'UIDE
- this will remove all packing
debris,
)NCORRECTTEMPERATUREISINDICATED
dust,
etc.
WHENTHEMESSAGEONTHE,%$
DISPLAYREADShT,Ov2EADYTOUSE
4HE6ELOPEXISEQUIPPEDWITH
ISINDICATEDBYTHREEHORIZONTAL
0LUGINELECTRICCORDANDSWITCH
Fill
tanks with their respective
AUTOMATICSTANDBYMODE4O
CENTRALLINESANDCOOLINGDOWNIS
0LUGINELECTRICCORDANDSWITCH
ON4HEMACHINEWILLTHENRUN
chemical
solutions or water, pouring
INITIATEPROCESSINGFEEDlLM
INDICATEDINTHELINESDESCENDING
ON4HEMACHINEWILLTHENRUN
THROUGHAHIGHSPEEDSTARTUP
inTHROUGH%NTRY3LOT)FTHATFAILS
1400ml of fluid.
FROMLEFTTORIGHT
THROUGHAHIGHSPEEDSTARTUP
CYCLEOFMINUTES
TOWORKSLIDElNGEROVER@25.
4)0
4HETIMETAKENTOACHIEVETHE
CYCLEOFMINUTES
TIP:
chemicals designed
3ENSOR
4)0Use VELOPEX
!FTERAPPROXTENMINUTESTHE
10
.
/PERATINGTHE0ROCESSOR
/PERATINGTHE0ROCESSOR
/0%2!4)/.
REACHEDTHEIRCORRECTTEMPERATURE
6%,/0%8).42!8
WARNING:
machine is
5SER'UIDE
7!2.).' Ensure
!LWAYSTURN
disconnected
from mains power
MAINSELECTRICITYSWITCHOFFATNIGHT
supply whilst filling. NEVER turn on the
machine with the tanks empty.
/0%2!4)/.
INSTALLATION
4)0
Remove
modules (see installation
PROCESSORWILLGOINTO@STANDBYMODE
BYWHICHTIMETHECHEMICALSWILLHAVE
sections
1-3b)
CORRECTTEMPERATUREDEPENDSONTHE
SHOULDBEWIPEDCLEANOFALLMOUTH
REACHEDTHEIRCORRECTTEMPERATURE
7!2.).'
!LWAYSTURN
CONTAMINANTS
7!2.).'
MAINSELECTRICITYSWITCHOFFATNIGHT
WARNING:
DO NOT!LWAYSTURN
use chemistry or
MAINSELECTRICITYSWITCHOFFATNIGHT
film
designed for manual processing.
4HE6ELOPEXISEQUIPPEDWITH
AUTOMATICSTANDBYMODE4O
)NCORRECTTEMPERATUREISINDICATED
INITIATEPROCESSINGFEEDlLM
)NCORRECTTEMPERATUREISINDICATED
WHENTHEMESSAGEONTHE,%$
THROUGH%NTRY3LOT)FTHATFAILS
WHENTHEMESSAGEONTHE,%$
DISPLAYREADShT,Ov
2EADYTOUSE
0%2!4)/.
2!4)/.
)MAGESFORINSTRUCTION/.,9
)MAGEFORINSTRUCTION/.,9
6IEWING7INDOWISCLOSEDWHEN
OPERATINGMACHINE
4)0
!FTERAPPROXTENMINUTESTHE
PROCESSORWILLGOINTO@STANDBYMODE
for
your unit.
If unobtainable use ONLY
ROOMTEMPERATUREUSUALLYMIN
7!2.).'
PROCESSORWILLGOINTO@STANDBYMODE
BYWHICHTIMETHECHEMICALSWILLHAVE
another
proprietary"EFOREPLACINGIN
chemical & always
THEMACHINEINTRAORALlLMPACKETS
BYWHICHTIMETHECHEMICALSWILLHAVE
REACHEDTHEIRCORRECTTEMPERATURE
read
and follow instructions on bottle.
EDGEOFTHE3IGHT'LASS
11.
EDGEOFTHE
Fill the tanks up to the lowest edge
of the Sight Glass.
6%,/0%8).42!8
5SER'UIDE
,OWER4RANSPORT-ODULES
INTOTHEIRRESPECTIVETANKS
THECORRECTLIQUIDLEVELWI
0LUGINELECTRICCORDANDSWITCH
HALFWAYUPTHESIGHTGLASS
ON4HEMACHINEWILLTHENRUN
/PERATINGTHE0ROCESSOR
12.
INSTALLATION
Filling with Chemicals (Cont.)
VELOPEX INTRA-X
7
&ILLTHETANK
User Guide
THROUGHAHIGHSPEEDSTARTUP
CYCLEOFMINUTES
Lower
Transport
Modules carefully 4HISLIQUI
7!2.).'
,OWER4RANSP
4)0their!FTERAPPROXTENMINUTESTHE
into
respective
tanks. Top up
SHOULDBEMAINTAINEDATALLTI
INTOTHEIRRES
- PROCESSORWILLGOINTO@STANDBYMODE
the correct liquid level will show
BYWHICHTIMETHECHEMICALSWILLHAVE
THECORRECT
half
way up the sight glass.
REACHEDTHEIRCORRECTTEMPERATURE
HALFWAYUPT
7!2.).'This liquid
!LWAYSTURN
WARNING:
level should be
MAINSELECTRICITYSWITCHOFFATNIGHT
maintained at all times.
6%,/0%8).42!8 6%,/0%8).42!8
5SER'UIDE
7!2.).'
5SER'UIDE
REACHEDTHEIRCORRECTTEMPERATURE
ELEMENTS
7!2.).'
!LWAYSTURN
WARNING:
Do NOT!LWAYSTURN
over grease.
7!2.).'
MAINSELECTRICITYSWITCHOFFATNIGHT
MAINSELECTRICITYSWITCHOFFATNIGHT
7!2.).'
$O./4O
'REASE)MME
GREASE
$EVELOPERAN
%2!4)/.
2!4)/.
)MAGESFORINSTRUCTION/.,9
/0%2!4)/.
.
13
/PERATINGTHE0ROCESSOR
/PERATINGTHE0ROCESSOR
SHOULDBEMAI
)NCORRECTTEMPERATUREISINDICATED
WHENTHEMESSAGEONTHE,%$
DISPLAYREADShT,Ov
2EADYTOUSE
0LUGINELECTRICCORDANDSWITCH
0LUGINELECTRICCORDANDSWITCH
'REASE)MMERSION(EATERS
Grease
immersion
heaters for
ISINDICATEDBYTHREEHORIZONTAL
ON4HEMACHINEWILLTHENRUN
ON4HEMACHINEWILLTHENRUN
developer
and
fixer
tanks
with the
$EVELOPERAND&IXERTANKS
CENTRALLINESANDCOOLINGDOWNIS
THROUGHAHIGHSPEEDSTARTUP
THROUGHAHIGHSPEEDSTARTUP
lubricant
provided.
LUBRICANTPROVIDED
INDICATEDINTHELINESDESCENDING
CYCLEOFMINUTES
CYCLEOFMINUTES
FROMLEFTTORIGHT
4)0Spread
!FTERAPPROXTENMINUTESTHE
TIP:
a thin smear of lubricant
4)0
!FTERAPPROXTENMINUTESTHE
4HETIMETAKENTOACHIEVETHE
PROCESSORWILLGOINTO@STANDBYMODE
4)0 metal
3PREADATHINSMEAR
over
the two projecting
heating
PROCESSORWILLGOINTO@STANDBYMODE
CORRECTTEMPERATUREDEPENDSONTHE
BYWHICHTIMETHECHEMICALSWILLHAVE
OVERTHETWOPROJECTINGMETA
BYWHICHTIMETHECHEMICALSWILLHAVE
elements.
ROOMTEMPERATUREUSUALLYMIN
REACHEDTHEIRCORRECTTEMPERATURE
4HE6ELOPEXISEQUIPPEDWITH
)NCORRECTTEMPERATUREISINDICATED
LUBRICANTPRO
)NCORRECTTEMPERATUREISINDICATED
AUTOMATICSTANDBYMODE4O
WHENTHEMESSAGEONTHE,%$
WHENTHEMESSAGEONTHE,%$
INITIATEPROCESSINGFEEDlLM
DISPLAYREADShT,Ov
2EADYTOUSE
8
VELOPEX INTRA-X
User Guide
14.
15a.
15
b.
INSTALLATION
Filling with Chemicals (Cont.)
/PERATINGTHE0ROCESSOR
/PERATINGTHE0ROCESSOR
6%,/0%8).42!8
5SER'UIDE
To avoid spillage, carefully return
tanks to the machine. Start with
the Developer6%,/0%8).42!8
tank followed by
5SER'UIDE
the Fixer, Water and
finally the
0LUGINELECTRICCORDANDSWITCH
Dryer tanks. Engage the module
ON4HEMACHINEWILLTHENRUN
drive pins into the drive dogs,
THROUGHAHIGHSPEEDSTARTUP
working from right to left.
CYCLEOFMINUTES
TIP: Slide
the developer and fixer
4)0
!FTERAPPROXTENMINUTESTHE
0LUGINELECTRICCORDANDSWITCH
tanks
sideways
onto the immersion
PROCESSORWILLGOINTO@STANDBYMODE
ON4HEMACHINEWILLTHENRUN
BYWHICHTIMETHECHEMICALSWILLHAVE
heaters
till
backed
up fully against
THROUGHAHIGHSPEEDSTARTUP
REACHEDTHEIRCORRECTTEMPERATURE
the
machine
internal
CYCLEOFMINUTES wall.
)MAGESFORINSTRUCTION/.,9
)MAGESFORINSTRUCTION/.,9
%2!4)/.
!4)/.
/PERATINGTHE0ROCESSOR
/PERATINGTHE0ROCESSOR
WARNING: Wipe
dry any spilled
7!2.).'
!LWAYSTURN
)NCORRECTTEMPERATUREISINDICATED
solution.
MAINSELECTRICITYSWITCHOFFATNIGHT
WHENTHEMESSAGEONTHE,%$
DISPLAYREADShT,Ov2EADYTOUSE
6%,/0%8).42!8 ISINDICATEDBYTHREEHORIZONTAL
5SER'UIDE
6%,/0%8).42!8 CENTRALLINESANDCOOLINGDOWNIS
5SER'UIDE
)NCORRECTTEMPERATUREISINDICATED
INDICATEDINTHELINESDESCENDING
WHENTHEMESSAGEONTHE,%$
FROMLEFTTORIGHT
DISPLAYREADShT,Ov2EADYTOUSE
4)0
4HETIMETAKENTOACHIEVETHE
ISINDICATEDBYTHREEHORIZONTAL
CORRECTTEMPERATUREDEPENDSONTHE
The
machine
may now be
0LUGINELECTRICCORDANDSWITCH
CENTRALLINESANDCOOLINGDOWNIS
ROOMTEMPERATUREUSUALLYMIN
switched
on.
ON4HEMACHINEWILLTHENRUN
0LUGINELECTRICCORDANDSWITCH
INDICATEDINTHELINESDESCENDING
THROUGHAHIGHSPEEDSTARTUP
ON4HEMACHINEWILLTHENRUN
FROMLEFTTORIGHT
CYCLEOFMINUTES
THROUGHAHIGHSPEEDSTARTUP
4)0
4HETIMETAKENTOACHIEVETHE
CYCLEOFMINUTES
CORRECTTEMPERATUREDEPENDSONTHE
4)0
!FTERAPPROXTENMINUTESTHE
TIP: Check
that all modules are
ROOMTEMPERATUREUSUALLYMIN
PROCESSORWILLGOINTO@STANDBYMODE
engaged
and running smoothly by
4)0
!FTERAPPROXTENMINUTESTHE
BYWHICHTIMETHECHEMICALSWILLHAVE
PROCESSORWILLGOINTO@STANDBYMODE
passing a ‘clean-up film’ through the
REACHEDTHEIRCORRECTTEMPERATURE
BYWHICHTIMETHECHEMICALSWILLHAVE
machine. If it fails to exit the machine,
4HE6ELOPEXISEQUIPPEDWITH
REACHEDTHEIRCORRECTTEMPERATURE
7!2.).'
!LWAYSTURN
check engagement
of modules.
AUTOMATICSTANDBYMODE4O
MAINSELECTRICITYSWITCHOFFATNIGHT
7!2.).'
!LWAYSTURN
INITIATEPROCESSINGFEEDlLM
WARNING: The machine will not
MAINSELECTRICITYSWITCHOFFATNIGHT
THROUGH%NTRY3LOT)FTHATFAILS
operate with the lid open.
TOWORKSLIDElNGEROVER@25.
4HE6ELOPEXISEQUIPPEDWITH
3ENSOR
AUTOMATICSTANDBYMODE4O
)NCORRECTTEMPERATUREISINDICATED
INITIATEPROCESSINGFEEDlLM
7!2.).'
"EFOREPLACINGIN
WHENTHEMESSAGEONTHE,%$
)NCORRECTTEMPERATUREISINDICATED
THROUGH%NTRY3LOT)FTHATFAILS
THEMACHINEINTRAORALlLMPACKETS
DISPLAYREADShT,Ov
2EADYTOUSE
WHENTHEMESSAGEONTHE,%$
TOWORKSLIDElNGEROVER@25.
/0%2!4)/.
/0%2!4)/.
7!2.).'
!LWAYSTURN
4)0
Return!FTERAPPROXTENMINUTESTHE
side panel and lid.
MAINSELECTRICITYSWITCHOFFATNIGHT
PROCESSORWILLGOINTO@STANDBYMODE
BYWHICHTIMETHECHEMICALSWILLHAVE
REACHEDTHEIRCORRECTTEMPERATURE
/PERATINGTHE0ROCESSOR
VELOPEX INTRA-X
9
User Guide6%,/0%8).42!
0LUGINELECTRICCORDANDSWITCH
5SER'UID
ON4HEMACHINEWILLTHENRUN
THROUGHAHIGHSPEEDSTARTUP
CYCLEOFMINUTES
1. Operating the Processor
/PERATINGTHE0ROCESSOR
4)0
!FTERAPPROXTENMINUTESTHE
Plug in electric
cord and switch on.
PROCESSORWILLGOINTO@STANDBYMODE
The machine0LUGINELECTRICCORDANDSWIT
will then run through
BYWHICHTIMETHECHEMICALSWILLHAVE
a high speedON4HEMACHINEWILLTHENRUN
start up cycle.
REACHEDTHEIRCORRECTTEMPERATURE
THROUGHAHIGHSPEEDSTARTUP
7!2.).'
!LWAYSTURN
WARNING: Always
turn mains
CYCLEOFMINUTES
MAINSELECTRICITYSWITCHOFFATNIGHT
)MAGESFORINSTRUCTION/.,9
)MAGEFORINSTRUCTION/.,9
6IEWING7INDOWISCLOSEDWHEN
OPERATINGMACHINE
(Images for instruction ONLY)
)MAGESFORINSTRUCTION/.,9
3.
/0%2!4)/.
OPERATION
/0%2!4)/.
/PERATINGTHE0ROCESSOR
/0%2!4)/.
2.
/PERATINGTHE0ROCESSOR
)MAGESFORINSTRUCTION/.,9
electricity switch off at night.
4)0
!FTERAPPROXTENMINUTES
PROCESSORWILLGOINTO@STANDBYMOD
BYWHICHTIMETHECHEMICALSWILLHAV
REACHEDTHEIRCORRECTTEMPERATURE
)NCORRECTTEMPERATUREISINDICATED
6%,/0%8).42!8!LWAYSTURN
WHENTHEMESSAGEONTHE,%$
7!2.).'
5SER'UIDE
DISPLAYREADShT,Ov
2EADYTOUSE
MAINSELECTRICITYSWITCHOFFATNIGH
ISINDICATEDBYTHREEHORIZONTAL
Incorrect temperature is indicated
CENTRALLINESANDCOOLINGDOWNIS
when the message on the LED
INDICATEDINTHELINESDESCENDING
displays reads “tLo”. Ready to use
FROMLEFTTORIGHT
0LUGINELECTRICCORDANDSWITCH
is indicated
by three horizontal
4)0
4HETIMETAKENTOACHIEVETHE
)NCORRECTTEMPERATUREISINDI
ON4HEMACHINEWILLTHENRUN
6%,/0%8).42!8
CORRECTTEMPERATUREDEPENDSONTHE
central lines,WHENTHEMESSAGEONTHE,%$
and
cooling
down is
5SER'UIDE
THROUGHAHIGHSPEEDSTARTUP
ROOMTEMPERATUREUSUALLYMIN
indicated inDISPLAYREADShT,Ov
the lines descending
2EADYTOU
CYCLEOFMINUTES
from left to right.
ISINDICATEDBYTHREEHORIZONT
4)0
TIP: The!FTERAPPROXTENMINUTESTHE
time taken to achieve the
CENTRALLINESANDCOOLINGDOW
PROCESSORWILLGOINTO@STANDBYMODE
correct temperature
depends on the
INDICATEDINTHELINESDESCEND
BYWHICHTIMETHECHEMICALSWILLHAVE
room temperature
(usually 10-15
0LUGINELECTRICCORDANDSWITCH
REACHEDTHEIRCORRECTTEMPERATURE
FROMLEFTTORIGHT
min.)
ON4HEMACHINEWILLTHENRUN
7!2.).'
4)0!LWAYSTURN
4HETIMETAKENTOACHIEVE
THROUGHAHIGHSPEEDSTARTUP
4HE6ELOPEXISEQUIPPEDWITH
MAINSELECTRICITYSWITCHOFFATNIGHT
CORRECTTEMPERATUREDEPENDSONTHE
CYCLEOFMINUTES
AUTOMATICSTANDBYMODE4O
ROOMTEMPERATUREUSUALLYM
The Velopex
is equipped with
INITIATEPROCESSINGFEEDlLM
4)0
!FTERAPPROXTENMINUTESTHE
automatic
stand-by mode. Touch
PROCESSORWILLGOINTO@STANDBYMODE
THROUGH%NTRY3LOT)FTHATFAILS
the Film Entry Slot to initiate
BYWHICHTIMETHECHEMICALSWILLHAVE
TOWORKSLIDElNGEROVER@25.
processing.
)NCORRECTTEMPERATUREISINDICATED
REACHEDTHEIRCORRECTTEMPERATURE
3ENSOR
WHENTHEMESSAGEONTHE,%$
7!2.).'
!LWAYSTURN
WARNING: Before
placing in the
DISPLAYREADShT,Ov
2EADYTOUSE
7!2.).'
"EFOREPLACINGIN
MAINSELECTRICITYSWITCHOFFATNIGHT
machine,
Intra
oral
film packets
ISINDICATEDBYTHREEHORIZONTAL
THEMACHINEINTRAORALlLMPACKETS
should
be
wiped
clean
of all mouth
SHOULDBEWIPEDCLEANOFALLMOUTH
CENTRALLINESANDCOOLINGDOWNIS
4HE6ELOPEXISEQUIPPEDWITH
contaminants.
CONTAMINANTS
INDICATEDINTHELINESDESCENDING
AUTOMATICSTANDBYMODE4O
FROMLEFTTORIGHT
INITIATEPROCESSINGFEEDlLM
)NCORRECTTEMPERATUREISINDICATED
4)0
4HETIMETAKENTOACHIEVETHE
THROUGH%NTRY3LOT)FTHATFAIL
WHENTHEMESSAGEONTHE,%$
CORRECTTEMPERATUREDEPENDSONTHE
TOWORKSLIDElNGEROVER@25.
DISPLAYREADShT,Ov
2EADYTOUSE
ROOMTEMPERATUREUSUALLYMIN
ISINDICATEDBYTHREEHORIZONTAL
3ENSOR
CENTRALLINESANDCOOLINGDOWNIS
7!2.).'
"EFOREPLACINGI
INDICATEDINTHELINESDESCENDING
10
VELOPEX INTRA-X
/PERATINGTHE0ROCESSOR
User Guide
4.
Operating the Processor
0LUGINELECTRICCORDANDSWITCH
ON4HEMACHINEWILLTHENRUN
(Cont.)
THROUGHAHIGHSPEEDSTARTUP
CYCLEOFMINUTES
Put
hands!FTERAPPROXTENMINUTESTHE
through loading ports
4)0
PROCESSORWILLGOINTO@STANDBYMODE
and
place film inside Daylight
BYWHICHTIMETHECHEMICALSWILLHAVE
Loader.
REACHEDTHEIRCORRECTTEMPERATURE
5.
OPERATION
)NCORRECTTEMPERATUREISINDICATED
WHENTHEMESSAGEONTHE,%$
DISPLAYREADShT,Ov2EADYTOUSE
ISINDICATEDBYTHREEHORIZONTAL
Put
hands through Loading Gloves
CENTRALLINESANDCOOLINGDOWNIS
and
strip
wrapping from film, insert
INDICATEDINTHELINESDESCENDING
film
into
Entry
Slot. Touch the Film
FROMLEFTTORIGHT
Entry
Slot
to
initiate
processing. A
4)0
4HETIMETAKENTOACHIEVETHE
bleep
will
indicate
film
detected.
CORRECTTEMPERATUREDEPENDSONTHE
/0%2!4)/.
WARNING:
remove old film
7!2.).'Always !LWAYSTURN
MAINSELECTRICITYSWITCHOFFATNIGHT
wrappers
from the loader.
ROOMTEMPERATUREUSUALLYMIN
)MAGESFORINSTRUCTION/.,9
6%,/0%8).42!8
5SER'UIDE
/PERATINGTHE0ROCESSOR
)MAGEFORINSTRUCTION/.,9
6IEWING7INDOWISCLOSEDWHEN
OPERATINGMACHINE
6.
4HE6ELOPEXISEQUIPPEDWITH
0LUGINELECTRICCORDANDSWITCH
When
liquid levels are below the
AUTOMATICSTANDBYMODE4O
ON4HEMACHINEWILLTHENRUN
sight
glass,
top up Chemicals and/
INITIATEPROCESSINGFEEDlLM
THROUGHAHIGHSPEEDSTARTUP
orTHROUGH%NTRY3LOT)FTHATFAILS
water (See Installation Sections
CYCLEOFMINUTES
10,TOWORKSLIDElNGEROVER@25.
11 and 12)
TIP:
Before!FTERAPPROXTENMINUTESTHE
processing, run through
4)0
3ENSOR
“clean-up
film” or any spare strip of
PROCESSORWILLGOINTO@STANDBYMODE
BYWHICHTIMETHECHEMICALSWILLHAVE
extra
oral film. This "EFOREPLACINGIN
helps to clean the
7!2.).'
REACHEDTHEIRCORRECTTEMPERATURE
THEMACHINEINTRAORALlLMPACKETS
transport
system.
SHOULDBEWIPEDCLEANOFALLMOUTH
WARNING:
The same!LWAYSTURN
film may be used
7!2.).'
forCONTAMINANTS
this purpose for one week, after
MAINSELECTRICITYSWITCHOFFATNIGHT
which discard the old film and use a
fresh one.
)NCORRECTTEMPERATUREISINDICATED
WHENTHEMESSAGEONTHE,%$
DISPLAYREADShT,Ov2EADYTOUSE
%2!4)/.
(Images for instruction ONLY)
6%,/0%8).42
USETHE
115SER'U
VELOPEX INTRA-X
User Guide
/PERATINGTHE0ROCESSOR
HALVETH
USEPRE
DOWNB
LOWERIN
0LUGINELECTRICCORDANDSWITCH
ON4HEMACHINEWILLTHENRUN
(Cont.)
THROUGHAHIGHSPEEDSTARTUP
CYCLEOFMINUTES
All4)0
films are
collected in the Film
!FTERAPPROXTENMINUTESTHE
!LLlLMSARECOLLECTEDINTHE
PROCESSORWILLGOINTO@STANDBYMODE
Catcher
at the rear of the machine.
/PERATINGTHE0ROCESSORCONT
Operating the Processor
7.
&ILM#ATCHERATTHEREAROFT
BYWHICHTIMETHECHEMICALSWILLHAVE
REACHEDTHEIRCORRECTTEMPERATURE
MACHINE
4)0
TO7ETv
W
7!2.).'
!TTHEENDOF
WASHEDW
DAYTURNOFFMAINSPOWERSWITCH
WHENNEE
/PERATINGTHE0ROCESSOR
8.
OPERATION
/0%2!4)/.
WARNING:
of the day turn 7!2.).'At the end
!LWAYSTURN
6%,/0%8).42!8
offMAINSELECTRICITYSWITCHOFFATNIGHT
mains power switch. 5SER'UIDE
)NCORRECTTEMPERATUREISINDICATED
0LUGINELECTRICCORDANDSWITCH
WHENTHEMESSAGEONTHE,%$
ON4HEMACHINEWILLTHENRUN
DISPLAYREADShT,Ov2EADYTOUSE
THROUGHAHIGHSPEEDSTARTUP
ISINDICATEDBYTHREEHORIZONTAL
CYCLEOFMINUTES
For
quick viewing of X-rays use the
CENTRALLINESANDCOOLINGDOWNIS
Endo
Slide.
To use: press the Endo
4)0
!FTERAPPROXTENMINUTESTHE
INDICATEDINTHELINESDESCENDING
&ORQUICKVIEWINGOF82AYS
slide
FULLY
down, by pressing the
PROCESSORWILLGOINTO@STANDBYMODE
FROMLEFTTORIGHT
6%,/0%8).42!8 USETHE%NDO3LIDEWHICHWIL
BYWHICHTIMETHECHEMICALSWILLHAVE
latch
and
lowering
the 5SER'UIDE
slide.
4)0
4HETIMETAKENTOACHIEVETHE
/PERATINGTHE0ROCESSOR
)MAGESFORINSTRUCTION/.,9
7!2.).
MUSTBER
NORMALP
REACHEDTHEIRCORRECTTEMPERATURE
HALVETHETIMEOFPROCESSING
CORRECTTEMPERATUREDEPENDSONTHE
WARNING:
The Endo
Slide must be
7!2.).'
!LWAYSTURN
ROOMTEMPERATUREUSUALLYMIN
USEPRESSTHE%NDO3LIDE&5,
returned
to the ‘UP’ position for normal
MAINSELECTRICITYSWITCHOFFATNIGHT
DOWNBYPRESSINGTHELATCHA
LOWERINGTHESLIDE
2EMOVE
0LUGINELECTRICCORDANDSWITCH
processing.
9.
4)0
ANDTHEN
ITUPTODR
ROOMTEMPERATUREUSUALLYMIN
THEMACHINEINTRAORALlLMPACKETS
SHOULDBEWIPEDCLEANOFALLMOUTH
CONTAMINANTS
2EMOVElLMFROM%.$/SLO
7!2.).
)NCORRECTTEMPERATUREISINDICATED
NOTFALLB
WHENTHEMESSAGEONTHE,%$
DISPLAYREADShT,Ov2EADYTOUSE
ITASSOON
/0%2!4)/.
)MAGEFORINSTRUCTION/.,9
)MAGESFORINSTRUCTION/.,9
6IEWING7INDOWISCLOSEDWHEN
OPERATINGMACHINE
/0%2!4)/.
ON4HEMACHINEWILLTHENRUN
4)0
4HISPROCEDUREISONLYh$
THROUGHAHIGHSPEEDSTARTUP
)NCORRECTTEMPERATUREISINDICATED
TO7ETvWHICHMEANSTHElLMSHO
CYCLEOFMINUTES
WHENTHEMESSAGEONTHE,%$
WASHEDWITHWATERANDHUNGUPT
4HE6ELOPEXISEQUIPPEDWITH
DISPLAYREADShT,Ov
2EADYTOUSE
Remove
film
from ENDO
slot.
4)0
!FTERAPPROXTENMINUTESTHE
AUTOMATICSTANDBYMODE4O
WHENNEEDEDFORARCHIVING
PROCESSORWILLGOINTO@STANDBYMODE
ISINDICATEDBYTHREEHORIZONTAL
INITIATEPROCESSINGFEEDlLM
BYWHICHTIMETHECHEMICALSWILLHAVE
CENTRALLINESANDCOOLINGDOWNIS
7!2.).'
4HE%NDO3LID
THROUGH%NTRY3LOT)FTHATFAILS
REACHEDTHEIRCORRECTTEMPERATURE
INDICATEDINTHELINESDESCENDING
MUSTBERETURNEDTOTHE@50POSITI
TOWORKSLIDElNGEROVER@25.
7!2.).'
!LWAYSTURN
FROMLEFTTORIGHT
WARNING:
Make sure
film does not
3ENSOR NORMALPROCESSING
4)0
4HETIMETAKENTOACHIEVETHE
fallMAINSELECTRICITYSWITCHOFFATNIGHT
back into
the Velopex - remove it as
CORRECTTEMPERATUREDEPENDSONTHE
soon
as it emerges. "EFOREPLACINGIN
7!2.).'
ISINDICATEDBYTHREEHORIZONTAL
4)0
!FTERlLMEXITSYOUCAN
CENTRALLINESANDCOOLINGDOWNIS
4HE6ELOPEXISEQUIPPEDWITH
INDICATEDINTHELINESDESCENDING
ANDTHENWASHITWITHWATERANDH
AUTOMATICSTANDBYMODE4O
FROMLEFTTORIGHT
ITUPTODRY
INITIATEPROCESSINGFEEDlLM
12
VELOPEX INTRA-X
User Guide
6%,/0%8).42!8
5SER'UIDE
/PERATINGTHE0ROCESSORCONT
10.
6%,/0%8).42!8
6%,/0%8).42!8
5SER'UIDE
5SER'UIDE
/PERATINGTHE0ROCESSOR
Operating the Processor (Cont.)
4)0
#ENTRETHElLMONTHEGUIDEPROVIDEDTOPOSTTHElLM
THROUGHTHEPROCESSOR
OPERATION
&ILM%NTRY
&ILM%NTRY
&ILM
/0%2!4)/.
7!2.).'
-AKESURETHElLMISFEDINSQUARELYANDIN
THECENTREOFTHEENTRYSLOTSHORTEDGELEADING!DOUBLE"LEEPWILL
INDICATETHATTHElLMHASBEENFULLYINSERTED
&ILM


0LUGINELECTRICCORDANDSWITCH
0LUGINELECTRICCORDANDSWITCH
ON4HEMACHINEWILLTHENRUN
ON4HEMACHINEWILLTHENRUN
Film
Feeding direction.
THROUGHAHIGHSPEEDSTARTUP
THROUGHAHIGHSPEEDSTARTUP
CYCLEOFMINUTES
CYCLEOFMINUTES
TIP:
the film on the guide
4)0Centre!FTERAPPROXTENMINUTESTHE
!FTERAPPROXTENMINUTESTHE
4)0
PROCESSORWILLGOINTO@STANDBYMODE
provided
to post the film through the
PROCESSORWILLGOINTO@STANDBYMODE
BYWHICHTIMETHECHEMICALSWILLHAVE
processor.
BYWHICHTIMETHECHEMICALSWILLHAVE
REACHEDTHEIRCORRECTTEMPERATURE
REACHEDTHEIRCORRECTTEMPERATURE
7!2.).'Make sure
!LWAYSTURN
WARNING:
the film is fed in
7!2.).'
!LWAYSTURN
MAINSELECTRICITYSWITCHOFFATNIGHT
squarely,
and in the centre of the entry
MAINSELECTRICITYSWITCHOFFATNIGHT
slot, short edge leading.
11.
/PERATINGTHE0ROCESSOR
)MAGESFORINSTRUCTION/.,9
)MAGESFORINSTRUCTION/.,9
)NCORRECTTEMPERATUREISINDICATED
6%,/0%8).42!8 )NCORRECTTEMPERATUREISINDICATED
5SER'UIDE
For
Reference, the machine
will
WHENTHEMESSAGEONTHE,%$
WHENTHEMESSAGEONTHE,%$
display
a countdown
in seconds
DISPLAYREADShT,Ov
2EADYTOUSE
DISPLAYREADShT,Ov2EADYTOUSE
from
the start to the end of the
ISINDICATEDBYTHREEHORIZONTAL
ISINDICATEDBYTHREEHORIZONTAL
process.
CENTRALLINESANDCOOLINGDOWNIS
CENTRALLINESANDCOOLINGDOWNIS
INDICATEDINTHELINESDESCENDING
INDICATEDINTHELINESDESCENDING
0LUGINELECTRICCORDANDSWITCH
FROMLEFTTORIGHT
FROMLEFTTORIGHT
ON4HEMACHINEWILLTHENRUN
4)0
4HETIMETAKENTOACHIEVETHE
4)0
4HETIMETAKENTOACHIEVETHE
THROUGHAHIGHSPEEDSTARTUP
CORRECTTEMPERATUREDEPENDSONTHE
CORRECTTEMPERATUREDEPENDSONTHE
CYCLEOFMINUTES
ROOMTEMPERATUREUSUALLYMIN
ROOMTEMPERATUREUSUALLYMIN
TIP:4)0
If the Lid
is opened during a cycle,
!FTERAPPROXTENMINUTESTHE
closing
it will initiate a “350 cycle” (test
PROCESSORWILLGOINTO@STANDBYMODE
BYWHICHTIMETHECHEMICALSWILLHAVE
only).
REACHEDTHEIRCORRECTTEMPERATURE
)MAGEFORINSTRUCTION/.,9
)MAGEFORINSTRUCTION/.,9
6IEWING7INDOWISCLOSEDWHEN
6IEWING7INDOWISCLOSEDWHEN
OPERATINGMACHINE
OPERATINGMACHINE
7!2.).'
!LWAYSTURN
MAINSELECTRICITYSWITCHOFFATNIGHT
4HE6ELOPEXISEQUIPPEDWITH
4HE6ELOPEXISEQUIPPEDWITH
AUTOMATICSTANDBYMODE4O
AUTOMATICSTANDBYMODE4O
INITIATEPROCESSINGFEEDlLM
INITIATEPROCESSINGFEEDlLM
THROUGH%NTRY3LOT)FTHATFAILS
THROUGH%NTRY3LOT)FTHATFAILS
)NCORRECTTEMPERATUREISINDICATED
TOWORKSLIDElNGEROVER@25.
TOWORKSLIDElNGEROVER@25.
WHENTHEMESSAGEONTHE,%$
3ENSOR
3ENSOR
DISPLAYREADShT,Ov2EADYTOUSE
ISINDICATEDBYTHREEHORIZONTAL
7!2.).'
"EFOREPLACINGIN
7!2.).'
"EFOREPLACINGIN
CENTRALLINESANDCOOLINGDOWNIS
THEMACHINEINTRAORALlLMPACKETS
THEMACHINEINTRAORALlLMPACKETS
SHOULDBEWIPEDCLEANOFALLMOUTH
INDICATEDINTHELINESDESCENDING
SHOULDBEWIPEDCLEANOFALLMOUTH
CONTAMINANTS
FROMLEFTTORIGHT
CONTAMINANTS
4)0
4HETIMETAKENTOACHIEVETHE
CORRECTTEMPERATUREDEPENDSONTHE
ROOMTEMPERATUREUSUALLYMIN
/0%2!4)/.
/0%2!4)/.
&ILM&EEDINGDIRECTION
1.
VELOPEX INTRA-X
13
6%,/0%8).42!8
User Guide
5SER'UIDE
/PERATINGTHE0ROCESSOR
It0LUGINELECTRICCORDANDSWITCH
is suggested that the VISCHECK
ON4HEMACHINEWILLTHENRUN
Quality
Manager be used to
THROUGHAHIGHSPEEDSTARTUP
ensure
consistent quality X-Rays.
CYCLEOFMINUTES
6%,/0%8).42!8 5SER'UIDE
TIP:
use of this
product
4)0Regular
!FTERAPPROXTENMINUTESTHE
PROCESSORWILLGOINTO@STANDBYMODE
will ensure that the quality of the
BYWHICHTIMETHECHEMICALSWILLHAVE
film
processing is maintained and
REACHEDTHEIRCORRECTTEMPERATURE
reduce
the risk of retakes. Vischeck
will
also tell you when
to change the
7!2.).'
!LWAYSTURN
0LUGINELECTRICCORDANDSWITCH
MAINSELECTRICITYSWITCHOFFATNIGHT
chemicals.
VISCHECK is available
ON4HEMACHINEWILLTHENRUN
from
your Velopex stockist.
THROUGHAHIGHSPEEDSTARTUP
CYCLEOFMINUTES
Open
Lid,
remove side cover,
4)0
!FTERAPPROXTENMINUTESTHE
)NCORRECTTEMPERATUREISINDICATED
PROCESSORWILLGOINTO@STANDBYMODE
tanks
&
modules
(see Installation
WHENTHEMESSAGEONTHE,%$
BYWHICHTIMETHECHEMICALSWILLHAVE
sections
1-3b
&
8-9).
DISPLAYREADShT,Ov2EADYTOUSE
2.
REACHEDTHEIRCORRECTTEMPERATURE
/PERATINGTHE0ROCESSOR
/PERATINGTHE0ROCESSOR
)MAGESFORINSTRUCTION/.,9
)MAGEFORINSTRUCTION/.,9
6IEWING7INDOWISCLOSEDWHEN
OPERATINGMACHINE
3.
CORRECTTEMPERATUREDEPENDSONTHE
ROOMTEMPERATUREUSUALLYMIN
)NCORRECTTEMPERATUREISINDICATED
WHENTHEMESSAGEONTHE,%$
0LUGINELECTRICCORDANDSWITCH
DISPLAYREADShT,Ov
2EADYTOUSE
0LUGINELECTRICCORDANDSWITCH
ON4HEMACHINEWILLTHENRUN
ISINDICATEDBYTHREEHORIZONTAL
ON4HEMACHINEWILLTHENRUN
Empty
tanks and dispose of
THROUGHAHIGHSPEEDSTARTUP
CENTRALLINESANDCOOLINGDOWNIS
THROUGHAHIGHSPEEDSTARTUP
chemistry.
CYCLEOFMINUTES
INDICATEDINTHELINESDESCENDING
CYCLEOFMINUTES
4)0
!FTERAPPROXTENMINUTESTHE
FROMLEFTTORIGHT
TIP:
Drain
modules over the tanks
4)0
!FTERAPPROXTENMINUTESTHE
PROCESSORWILLGOINTO@STANDBYMODE
4HE6ELOPEXISEQUIPPEDWITH
4)0
4HETIMETAKENTOACHIEVETHE
PROCESSORWILLGOINTO@STANDBYMODE
before
removing
them.
BYWHICHTIMETHECHEMICALSWILLHAVE
AUTOMATICSTANDBYMODE4O
CORRECTTEMPERATUREDEPENDSONTHE
BYWHICHTIMETHECHEMICALSWILLHAVE
REACHEDTHEIRCORRECTTEMPERATURE
INITIATEPROCESSINGFEEDlLM
ROOMTEMPERATUREUSUALLYMIN
REACHEDTHEIRCORRECTTEMPERATURE
WARNING:
and handle
7!2.).'Use gloves
!LWAYSTURN
THROUGH%NTRY3LOT)FTHATFAILS
with
care.
Be
aware
that
chemicals
7!2.).'
!LWAYSTURN
MAINSELECTRICITYSWITCHOFFATNIGHT
TOWORKSLIDElNGEROVER@25.
MAINSELECTRICITYSWITCHOFFATNIGHT
can
cause staining or corrosion of
3ENSOR
surfaces and may cause skin and eye
irritation.
Wipe away
any spillage
7!2.).'
"EFOREPLACINGIN
THEMACHINEINTRAORALlLMPACKETS
immediately
and flush with copious
)NCORRECTTEMPERATUREISINDICATED
SHOULDBEWIPEDCLEANOFALLMOUTH
amounts
of water.
4HE6ELOPEXISEQUIPPEDWITH
)NCORRECTTEMPERATUREISINDICATED
WHENTHEMESSAGEONTHE,%$
CONTAMINANTS
AUTOMATICSTANDBYMODE4O
WHENTHEMESSAGEONTHE,%$
DISPLAYREADShT,Ov
2EADYTOUSE
INITIATEPROCESSINGFEEDlLM
DISPLAYREADShT,Ov2EADYTOUSE
ISINDICATEDBYTHREEHORIZONTAL
THROUGH%NTRY3LOT)FTHATFAILS
ISINDICATEDBYTHREEHORIZONTAL
CENTRALLINESANDCOOLINGDOWNIS
/0%2!4)/.
0%2!4)/.
)MAGESFORINSTRUCTION/.,9
MAINTENANCE
/0%2!4)/.
ISINDICATEDBYTHREEHORIZONTAL
WARNING:
Carry out
the cleaning
7!2.).'
!LWAYSTURN
CENTRALLINESANDCOOLINGDOWNIS
MAINSELECTRICITYSWITCHOFFATNIGHT
routine
at
each
chemical
change, 6%,/0%8).42!8
INDICATEDINTHELINESDESCENDING
5SER'UIDE
6%,/0%8).42!8
approx.
once
every
three
to four FROMLEFTTORIGHT
5SER'UIDE
weeks,
according
to use.
4)0
4HETIMETAKENTOACHIEVETHE
/0%2!4)/.
Velopex
Processor
Changing
Chemistry
Operating
the Processor
(cont.)
/PERATINGTHE0ROCESSOR
14
VELOPEX INTRA-X
User Guide
Velopex Processor Changing Chemistry (Cont.)
MAINTENANCE
5.
Rinse tanks thoroughly with fresh
cold water.
6%,/0%8).42!8
5SER'UIDE
6.
/PERATINGTHE0ROCESSOR
Fill up with Chemicals (See
Installation sections 10-12, pages
6-7).
0LUGINELECTRICCORDANDSWITCH
For
best results, use VELOPEX
ON4HEMACHINEWILLTHENRUN
chemicals.
THROUGHAHIGHSPEEDSTARTUP
CYCLEOFMINUTES
TIP:
Use the chart provided and keep
a4)0
note of!FTERAPPROXTENMINUTESTHE
the date when chemicals
PROCESSORWILLGOINTO@STANDBYMODE
were
changed.
BYWHICHTIMETHECHEMICALSWILLHAVE
REACHEDTHEIRCORRECTTEMPERATURE
7!2.).'
!LWAYSTURN
MAINSELECTRICITYSWITCHOFFATNIGHT
)/.
4.
Add Velopex Cleaning Tablets,
one per tank and leave for one
hour.
1.
REACHEDTHEIRCORRECTTEMPERATURE
2EPLACE-ODULESANDRUN
FOR47/CYCLESATOPERATING
TIP:
The interior of the
daylight loader
7!2.).'
!LWAYSTURN
TEMPERATURE
should
be
cleaned
with
cold sterilising
MAINSELECTRICITYSWITCHOFFATNIGHT
WARNING: Wear gloves contamination
Biohazard.
)NCORRECTTEMPERATUREISINDICATED
WHENTHEMESSAGEONTHE,%$
6%,/0%8).42!8
DISPLAYREADShT,Ov
2EADYTOUSE
5SER'UIDE
ISINDICATEDBYTHREEHORIZONTAL
Dryer
Module Cleaning - Place
CENTRALLINESANDCOOLINGDOWNIS
$RYER-ODULE#LEANING0LACE
Module
in container or sink filled
-ODULEINCONTAINERORSINK
INDICATEDINTHELINESDESCENDING
lLLEDWITHFRESHCOLDWATER!DD
with
fresh cold water. Add one
FROMLEFTTORIGHT
ONE6ELOPEX#LEANING4ABLET
Velopex
Cleaning Tablet and
4)0
4HETIMETAKENTOACHIEVETHE
0LUGINELECTRICCORDANDSWITCH
ANDSOAKFORATLEASTMINUTES
soak
for at least 10 minutes. Rinse
CORRECTTEMPERATUREDEPENDSONTHE
ON4HEMACHINEWILLTHENRUN
2INSETHOROUGHLYWITHWATERTO
ROOMTEMPERATUREUSUALLYMIN
thoroughly
with water to remove
REMOVEALLCLEANINGSOLUTION
THROUGHAHIGHSPEEDSTARTUP
all cleaning solution.
4)0 CYCLEOFMINUTES
!DDALITTLEDOMESTICFABRIC
TIP:
a little domestic fabric
SOFTENERTOTHEWASHINGWATERTOAVOID
4)0 Add !FTERAPPROXTENMINUTESTHE
@STATIC
$/./453%&!"2)#3/&4%.%2
softener
to
the washing water
PROCESSORWILLGOINTO@STANDBYMODE
/.4(%/4(%2-/$5,%3
toBYWHICHTIMETHECHEMICALSWILLHAVE
avoid ‘static’. DO NOT USE
7!2.).'
-AKESUREYOU
REACHEDTHEIRCORRECTTEMPERATURE
FABRIC
SOFTENER
ON THE OTHER
DRIPDRYTHEMODULEBEFOREREPLACING
MODULES!
7!2.).'
!LWAYSTURN
INTHEDRYERCOMPARTMENT
4HE6ELOPEXISEQUIPPEDWITH
MAINTENANCE
MAINSELECTRICITYSWITCHOFFATNIGHT
AUTOMATICSTANDBYMODE4O
WARNING:
Make sure you drip-dry
theINITIATEPROCESSINGFEEDlLM
module before replacing in the
THROUGH%NTRY3LOT)FTHATFAILS
dryer
compartment.
TOWORKSLIDElNGEROVER@25.
3ENSOR
)NCORRECTTEMPERATUREISINDICATED
)MAGEFORINSTRUCTION/.,9
6IEWING7INDOWISCLOSEDWHEN
OPERATINGMACHINE
WHENTHEMESSAGEONTHE,%$
7!2.).'
"EFOREPLACINGIN
DISPLAYREADShT,Ov
2EADYTOUSE
THEMACHINEINTRAORALlLMPACKETS
ISINDICATEDBYTHREEHORIZONTAL
SHOULDBEWIPEDCLEANOFALLMOUTH
CENTRALLINESANDCOOLINGDOWNIS
CONTAMINANTS
INDICATEDINTHELINESDESCENDING
FROMLEFTTORIGHT
4)0
4HETIMETAKENTOACHIEVETHE
CORRECTTEMPERATUREDEPENDSONTHE
ROOMTEMPERATUREUSUALLYMIN
)MAGESFORINSTRUCTION/.,9
/0%2!4)/.
solution. Wipe dry after appropriate
period.
/0%2!4)/.
)MAGESFORINSTRUCTION/.,9
15
4)0
!FTERAPPROXTENMINUTESTHE
Remove
old
film wrappers from
PROCESSORWILLGOINTO@STANDBYMODE
daylight loader. Wipe clean the
BYWHICHTIMETHECHEMICALSWILLHAVE
interior
of loader.
2.
/PERATINGTHE0ROCESSOR
VELOPEX INTRA-X
User Guide
0LUGINELECTRICCORDANDSWITCH
ON4HEMACHINEWILLTHENRUN
THROUGHAHIGHSPEEDSTARTUP
CYCLEOFMINUTES
Velopex Processor Cleaning
-!).4%.!.#%
/PERATINGTHE0ROCESSOR
!DD6ELOPEX#LEANING4ABLETS
ONEPERTANK
16
VELOPEX INTRA-X
User Guide
Velopex Processor Cleaning (Cont.)
4.
Drain Module over the tank
before removing.
6%,/0%8).42!8
5SER'UIDE
6%,/0%8).42!8
5SER'UIDE
/PERATINGTHE0ROCESSOR
6ELOPEX0ROCESSOR#LEANINGCONT
/PERATINGTHE0ROCESSOR
6.
ON4HEMACHINEWILLTHENRUN
7!2.).'
$/./4USE
THROUGHAHIGHSPEEDSTARTUP
BOILINGWATERITWILLDAMAGETHE
CYCLEOFMINUTES
MODULES5SE/.,9COLDWATER
)NCORRECTTEMPERATUREISINDICATED
Place
the module6%,/0%8).42!8
in a washing-up WHENCLEANINGTHEMACHINETANKS
WHENTHEMESSAGEONTHE,%$
bowl
fresh cold 5SER'UIDE
water. Add
4)0 with
!FTERAPPROXTENMINUTESTHE
/PERATINGTHE0ROCESSOR
-!).4%.!.#%
7!2.).'
!LWAYSTURN
4)0
5SETHETURNINGTOOLTURN
MAINSELECTRICITYSWITCHOFFATNIGHT
THEGEARSANDBELTSBYHANDTOASSISTIN
0LUGINELECTRICCORDANDSWITCH
THOROUGHCLEANING
)MAGESFORINSTRUCTION/.,9
PROCESSORWILLGOINTO@STANDBYMODE
DISPLAYREADShT,Ov
2EADYTOUSE
three
tablets to each
bowl and
BYWHICHTIMETHECHEMICALSWILLHAVE
#LEANTHE-ODULESUSINGTHE
ISINDICATEDBYTHREEHORIZONTAL
leave
to soak overnight.
REACHEDTHEIRCORRECTTEMPERATURE
6ELOPEX#LEANING4ABLETS
CENTRALLINESANDCOOLINGDOWNIS
%MPTY#HEMICALAND7ATER
7!2.).' DO NOT
!LWAYSTURN
INDICATEDINTHELINESDESCENDING
WARNING:
MIX MODULES
0LUGINELECTRICCORDANDSWITCH
MAINSELECTRICITYSWITCHOFFATNIGHT
TANKS2ElLLWITHFRESHCOLD
FROMLEFTTORIGHT
DURING
CLEANING. Ensure that
ON4HEMACHINEWILLTHENRUN
4)0
4HETIMETAKENTOACHIEVETHE
WATER
the
correct
module goes into its
THROUGHAHIGHSPEEDSTARTUP
CORRECTTEMPERATUREDEPENDSONTHE
corresponding
tank.
7!2.).'
$ONOTEMPTY
CYCLEOFMINUTES
ROOMTEMPERATUREUSUALLYMIN
CLEANINGSOLUTIONINTOCONTAINERS
TIP:
Clean!FTERAPPROXTENMINUTESTHE
one module at a time and
4)0
CONTAININGPROCESSINGCHEMICALS
)NCORRECTTEMPERATUREISINDICATED
PROCESSORWILLGOINTO@STANDBYMODE
leave
to
soak
overnight.
&/,,/7).3425#4)/.33500,)%$
WHENTHEMESSAGEONTHE,%$
BYWHICHTIMETHECHEMICALSWILLHAVE
7)4(#,%!.).'4!",%43
DISPLAYREADShT,Ov
2EADYTOUSE
REACHEDTHEIRCORRECTTEMPERATURE
ISINDICATEDBYTHREEHORIZONTAL
7!2.).'
!LWAYSTURN
CENTRALLINESANDCOOLINGDOWNIS
MAINSELECTRICITYSWITCHOFFATNIGHT
INDICATEDINTHELINESDESCENDING
4HE6ELOPEXISEQUIPPEDWITH
/0%2!4)/.
MAINTENANCE

5.
0LUGINELECTRICCORDANDSWITCH
Rinse
thoroughly with cold water
ON4HEMACHINEWILLTHENRUN
and
lightly scrub gears and
-ODULECLEANING)MMERSETHE
THROUGHAHIGHSPEEDSTARTUP
rollers.
-ODULESINATANKSINKlLLED
CYCLEOFMINUTES
O
WITHHOTWATER
TIP:
the turning #APPROX
tool; turn the
4)0 Use !FTERAPPROXTENMINUTESTHE
6%,/0%8).42!8
ANDSCRUBWITHTHESUPPLIED
gears
and
belts
by
hand
to assist in PROCESSORWILLGOINTO@STANDBYMODE
5SER'UIDE
BRUSHAROUNDTHEGEARSAND
BYWHICHTIMETHECHEMICALSWILLHAVE
thorough
cleaning.
ROLLERENDS
REACHEDTHEIRCORRECTTEMPERATURE
Display
Characters
E03
VELOPEX INTRA-X
User Guide
Description
Action
Call for Service
E10
E11
Dryer temperature sensor s/c
Dryer temperature sensor o/c
or connection to Main PCB
Fixer temperature sensor s/c
Fixer temperature sensor o/c
Developer temperature sensor
s/c
Developer temperature sensor
o/c
Fan Sensor Inactive
Drive turns count not zero
E12
Drive motor overloaded
E13
Transport motor Sensor
Inactive
or Modules seized
1. Switch off the Machine
2. Clean the gears and belts
on the Modules.
3. Switch on the machine
4. If still E13 - Call for Service
E14
Excessive Fixer / Developer
temperature
Call for Service
E04
E05
E06
E07
E08
E15
E18
E33
E34
tLO
LId
17
Call for Service
Call for Service
Call for Service
Call for Service
Call for Service
Call for Service
Call for Service
1. Switch off the Machine .
2. Clean the Gears on the
Modules.
3. Switch on the Machine.
4. If still E12 - Call for Service.
Dryer temperature too high
Dryer power duty cycle too low
Watchdog relay test failure
(Low)
Watchdog relay test failure
(High)
Either Developer or Fixer tank
temperature is low
Call for Service
Call for Service
Wait for the correct
temperature
Lid switch open
Close lid
Call for Service
Call for Service
TROUBLE SHOOTING
Display Error Codes
-ACHINEDOESNOT
OPERATE
4EMPERATURE)NDICATOR
$ISPLAYED
!#4)/.3
#HECK-AINS0OWERISPLUGGEDINANDSUPPLYSWITCHEDON./4%6ELOPEX-ACHINEWILLRUNONE
CYCLEWHENSWITCHEDONANDLIDINCORRECTPOSITION
)FTHELIDISNOTCORRECTLYCLOSEDTHESAFETYMECHANISMWILLPREVENTTHEMACHINEFROMOPERATING
#HECKBYOPENINGANDCLOSINGAGAIN/THERWISECALLFORSERVICE
#HECKTHATCORDISFULLYENGAGEDINBOTHPLUGANDSOCKETONTHEBACKOFTHEMACHINE
,ID/PEN$ISPLAYED
#ORD
#HECKTHATBARISFULLYINTHE@UPPOSITION
%.$/@INTERRUPTBAR
3TATIC%LECTRICITYINTHE !DDALITTLEDOMESTICFABRICSOFTENERTOTHEWASHINGWATERWHENWASHINGDRYERMODULETOAVOID
$RYER3ECTIONOFTHE @STATIC)-0/24!.4&ABRICSOFTENERSHOULDBEUSEDONTHE$RYER-ODULE/.,9DO./4USEIT
-ACHINE
ONTHE$EVELOPER&IXEROR7ATER-ODULES
2EPLACEA-ODULE
#HECKTHATALLTRANSPORTMODULESHAVEBEENPUTTHROUGHTHECORRECTCLEANINGPROCEDURE
#HECKTHESPRINGSONTHEMODULESFORCORRECTPOSITIONING5SETHEMODULETURNINGTOOLTO
ROTATETHEBELTSFORINSPECTIONANDRUNATESTlLMTHROUGHTHEMODULEUSINGTHISTOOL
$AMAGED4ORN"ELT
&ILM,OSTINTHE-ACHINE $IRTY4RANSPORT
-ODULES
7RONG0OSITIONING
OF4RANSPORT-ODULE
3PRING
#HECKINDIVIDUAL-ODULEBYROTATINGWITHTURNINGTOOLTOMANUALLYFEEDlLM#HECKTHATTHE
4RANSPORT-ODULESNOT
TRANSPORTMODULESARECORRECTLYLOCATEDINTHEIRDRIVEDOGSANDRUNNINGCORRECTLY)FNOTRE
IN0LACE
LOCATE
Troubleshooting (Cont.)
4RANSPORT-ODULESNOT
/PENMACHINELIDANDCHECKCORRECTENGAGEMENTOFTRANSPORTMODULES
IN0LACE
VELOPEX INTRA-X
-ACHINEISIN@STANDBY
Entry guide
3WIPElNGERACROSSTHE@2UNSWITCHMACHINEMAYBEIN@STANDBYMODE
MODE
$/./453%-!#().%#ALLFOR3ERVICE
!TNORMALROOMTEMPERATUREAVERAGEWARMUPTIMEISMINUTESINANUNHEATED
ENVIRONMENTTHISTIMECOULDLENGTHEN)FDISPLAYSTAYSONFORANABNORMALLYLONGTIMECALLFOR
SERVICE
#ALLFOR3ERVICE
"LOWN&USE
-ACHINEISIN@STANDBY
Entry guide
#[email protected]@STANDBYMODE
MODE
0OWER3UPPLY
0/33)",%#!53%
6%,/0%8).42!8
User Guide
5SER'UIDE
&ILMS$O.OT%NTER
THROUGH&ILM%NTRY
'UIDE
3OLUTIONOVERHEATING
39-04/-
.O
TROUBLE SHOOTING
42/5",%3(//4).'
18
39-04/-
0/33)",%#!53%
!#4)/.3
#HECKTHATTHEREHASBEENNOCHEMICALMIXUPLEADINGTOCROSSCONTAMINATION
#HECKTHATTHE$EVELOPERHASBEENCORRECTLYMIXEDIFRELEVANT
#HEMICAL
#ONTAMINATION
-IXINGOF$EVELOPER
TROUBLE SHOOTING
42/5",%3(/54).'
#HECKTEMPERATUREOF$EVELOPERAND&IXERTANKS4HESEAREGENERALLYSETAT$EVELOPERŽ&
Ž#&IXERŽ&Ž#)FTHE$EVELOPERTEMPERATUREISSIGNIlCANTLYHIGHERITCOULDLEADTO
DARKlLM3WITCHOFFTHEMACHINEANDCALLFORSERVICE
#HECK%XPIRYDATEONlLMBOXTOENSURElLMSARENOTOUTOFDATE+EEPlLMSINCOOLDRYPLACE
EXCESSIVEHEATCANCAUSEPREMATUREAGEINGOFlLM
&ILM%XPIRED
4EMPERATURE8%
EXCLUDED
#HECKWHETHERlLMSHAVEBEENSTOREDTOOCLOSETO8RAYSOURCEANDRELOCATEREPLACE
#HECKTHATWINDOWCOVERONLOADERHASBEENCORRECTLYREPLACEDANDCHECKATHANDENTRYPORTS
TOENSURETHEREISAGOODLIGHTSEALAROUNDTHEWRISTSIFNOTCALLFORSERVICE
$ONOTREMOVEYOURHANDSOUTOFTHEHANDENTRYPORTSBEFORETHElLMHASFEDCOMPLETELY
INTOTHEMACHINEFOGATONEENDONLYOFTHElLMINDICATESPREMATUREREMOVALOFHANDSFROM
DAYLIGHTLOADER
#LOSETO8RAY3OURCE
,IGHT,EAKS
#HECKTHATTHEDAYLIGHTLOADERISlRMLYSECUREDINCLUDINGREMOVALOFCOVERTAPESFROMSELF
ADHESIVEMOUNTING
$AYLIGHT,OADERNOT
3ECURED
$ARK&ILM
4HEREIS,IGHT&OG
#HECKTHATTHEDARKROOMISLIGHTTIGHTANDTHATTHESAFELIGHTISSOUNDEGPROCESSATESTlLM
WITHSAFELIGHTOFF $ARKROOMNOT,IGHT
4IGHT
7HENTHE$AYLIGHTLOADERISUSEDENSURETHATTHEMACHINEHASNOTBEENSITEDINDIRECTSUNLIGHT
ORININTENSELIGHTINGCONDITIONSEGDIRECTLYUNDERSPOTLIGHTSORSTRIPLIGHTS
#HECKTHATTHETOPLIDISlRMLYINPLACENOLIDDISPLAYON
,ID/PEN
4ESTFORLIGHTFOGBYFEEDINGANUNEXPOSEDlLMTHROUGHTHEMACHINE)TSHOULDPROCESSASATRANSPARENTPIECEOFlLMBASEANDTHERESHOULDBENO
SHADOWSORBLACKNESSONIT2%'5,!253%/&6)3#(%#+)34(%"%344//,&/2%!2,9$)!'./3)3/&02/#%33).'!.$82!902/",%-3
&ILMSTOO$ARK
.O
Troubleshooting (Cont.)
VELOPEX INTRA-X
19
6%,/0%8).42!8 User5SER'UIDE
Guide
39-04/-
3UDDEN#HANGEIN
)MAGE$ENSITY
#LEANMODULETHOROUGHLYANDCHANGEWATERDAILYINSUFlCIENTCLEANINGCANLEADTOABUILDUP
OFALGAE
#HECKTRANSPORTMODULESAREBEINGCLEANEDCORRECTLYSEECLEANINGINSTRUCTIONSABOVE
7ATER4ANK$IRTY
4RANSPORT-ODULES
$IRTY
#HECKFORSTRAYLIGHTENTERINGMACHINEPROCEEDASFORFOGGINGSEESYMPTOM
-AKESURESOLUTIONSAREINCORRECTTANKS
2EPLACE$EVELOPERIFCONTAMINATEDWITH&IXER
#HECK$EVELOPERTEMPERATURE
#HECK8RAYUNIT
,IGHT,EAKS
7RONG3OLUTIONS
$EVELOPER
#ONTAMINATION
4EMPERATURE
8RAY5NIT
7RONG0OSITIONINGOF )FFOUNDINWRONGORDERCONTAMINATIONWILLHAVEOCCURRED4HOROUGHLYCLEANMODULESAND
-ODULES
TANKSRElLLWITHFRESHCHEMICALS
Troubleshooting (Cont.)
#HEMICAL,EVELTOO,OW 4OPUP
#HECKlLMSHAVEBEENEXPOSEDCORRECTLY
&ILM%XPOSURE
4EMPERATURETOO,OW )FDISPLAYMESSAGEDOESNOTGOOUTCHECKWITHATHERMOMETERGENERALLYSETAT$EVELOPERŽ&
8%EXCLUDED
Ž#&IXERŽ&Ž#IFSIGNIlCANTLYBELOWTHESETEMPERATURESCALLFORSERVICE
#HEMICAL,EVELTOO,OW 4OPUP
VELOPEX INTRA-X
#LEANMACHINEREPLACECHEMICALSWITHFRESHSOLUTIONS
#HEMICALS
#ONTAMINATED
$EVELOPER)NCORRECTLY
2EPLACEWITHFRESHIFRELEVANT
-IXED
2EPLACEWITHFRESHTHISWILLDEPENDONVOLUMEOFlLMBEINGPROCESSEDANDLENGTHOFTIME
SINCELASTCHEMICALCHANGE
!#4)/.3
#HEMICALS%XHAUSTED
0/33)",%#!53%
6%,/0%8).42!8
User Guide
5SER'UIDE
&ILMS$IRTYOR-ARKED
&ILMSTOO,IGHT
.O
TROUBLE SHOOTING
42/5",%3(//4).'
20
39-04/-
"LACK0ARALLEL,INES
!#4)/.3
TROUBLE SHOOTING
7HITE/PAQUE0ATCHES 4EMPERATURE
ON,OW$ENSITY!REAS
)NDICATES,ACKOF&IXING &IXER
3TATIC$AMAGE
"ELTS*AMMED
$IRT
#HECKFOR$RYER-ODULECONTAMINATEDBYlXERDEPOSITS
&IXER$EPOSITS
#HECKFOREXHAUSTED&IXER
#HECK&IXERTEMPERATURE
4AKESTHEFORMOFDOTSFERNLIKELINESORLIGHTENINGSTRIKESCHECKFOR,/7AMBIENTHUMIDITYIN
PROCESSINGAREA#LEANAREAWITHANTISTATICSOLUTION
#HECKBELTSARETURNINGPROPERLY
#LEAN-ODULES
#LEANBRIDGEOVERROLLERS
#LEANENTRYSLOTORFEEDGUIDES
#HECKFORCONTAMINATEDORWRONGLYMIXED&IXER
&IXER
-AKESURE$RYERISWORKINGANDBLOWINGHOTAIR
$RYER
(UMIDITY
,OOKFORPOORAIRCIRCULATIONOR()'(HUMIDITYINPROCESSINGAREA
%LECTRICAL#OMPONENT
3WITCHOFFMACHINE3WITCHONAGAINAFTERSECONDS)FSTILLNOTDRYINGCALLFOR3ERVICE
0/33)",%#!53%
,IGHT!REASON&ILM
$ARK!REASON&ILM
7HITE-ARKS
$EPOSITSON&ILM
&ILMNOT$RYING
.O
Troubleshooting (Cont.)
VELOPEX INTRA-X
21
6%,/0%8).42!8
User Guide
5SER'UIDE
39-04/-
!BNORMAL/DOUR
/VERHEATEDOR5NUSUAL
.OISES
3EEABOVE3YMPTOM
,IGHT&OGGING
,IGHT,EAK
#HEMICALS
)MMEDIATELYSWITCHPROCESSOROFFANDUNPLUGFROM-AINS0OWER3UPPLY#ONTACTYOUR
SUPPLIER
-AKESURETHATTHE6IEWER#OVERONTHE$AYLIGHT,OADERISCOVEREDWITHALIGHTTIGHTTOPSUCH
ASTHESUPPLIED6ISCHECK1UALITY-ANAGER#ARDBOARD"OXORANYOTHERMATERIALTHATWOULD
BLOCKTHELIGHT
7HENCHANGING#HEMICALSMAKESURETHETANKSARECOMPLETELYEMPTYANDRINSEDOUT&RESH
CHEMICALWILLBESPOILEDBYCONTAMINATIONLEADINGTOPOORRESULTS
!FTERTHEPROCESSORHASBEENRUNNINGFORTWOMINUTESCHECKTHATTHEAIRCOMINGOUTOFTHEVENT
!IR#OMING/UTOFTHE
OVERTHE$RYERMODULEISWARM)FNOTSWITCHTHEPROCESSOROFFATTHE-AINS0OWER3WITCHFOR
6ENTIS./47ARM
TWOMINUTESANDSWITCHITONAGAIN)FTHATDOESNOTCORRECTTHEFAULTCALLFORSERVICE
#HECKAGEANDSTORAGECONDITIONSOFlLM
&ILM%XPIRED
#LEAN-ODULES
!#4)/.3
Troubleshooting (Cont.)
6ISCHECKlLMFOGGY
DARK
0/33)",%#!53%
$IRTY4RANSPORT
-ODULES
VELOPEX INTRA-X
6%,/0%8).42!8
User Guide
5SER'UIDE
#ONTAMINATION
&ILMSCOMING/UT7ET
-OTTLE
.O
42/5",%3(//4).'
TROUBLE SHOOTING
22
Service Log
VELOPEX INTRA-X
User Guide
3ERVICE,OG
$ATE
3ERVICE$ESCRIPTION
Machine Installation
3ERVICED"Y
23
ETL LISTED/ENREGISTRÉ ETL
CONFORMS TO/CONFORME À
UL 61010-1
C
THIS PRODUCT HAS BEEN TESTED
TO THE REQUIREMENTS OF
CAN/CSA-C22.2 No. 61010-1
SECOND EDITION INCLUDING AMENDMENT 1
OR A LATER VERSION OF THE SAME STANDARD
INCORPORATING THE SAME LEVEL OF TESTING
REQUIREMENTS. C No. 113778
ETL Testing Laboratories
www.velopex.com
Hi-Tech
Diagnostics
Service
MAKERS OF DENTAL, VETERINARY AND MEDICAL EQUIPMENT
US