Download II-EVB-600 User Manual

Instant Internet
Evaluation Board
II-EVB-600
User Manual
Version 1.1
International:
Connect One Ltd.
20 Atir Yeda Street
Kfar Saba 44643, Israel
Tel: +972-9-766-0456
Fax: +972-9-766-0461
E-mail:
[email protected]
http://www.connectone.com
USA:
Connect One
Semiconductors, Inc.
560 S. Winchester Blvd.
Suite 500
San Jose, CA 95128
Tel: (408) 572-5675
Fax: (408) 572-5601
II-EVB-600 User Manual
Program License Agreement
Program License Agreement
The information in this document is subject to change without notice and shall not be construed
as a commitment on the part of Connect One.
Connect One assumes no liability for any errors that may appear in this document.
The software described in this document is furnished under a license agreement and may be
used or copied only in accordance with the terms of such a license agreement. It is forbidden by
law to copy the software on any medium except as specifically allowed in the license agreement.
No part of this document may be reproduced or transmitted in any form or by any means,
electronic or mechanical, including but not limited to photocopying, recording, transmitting via
fax and/or modem devices, scanning, and/or information storage and retrieval systems for any
purpose without the express written consent of Connect One.
iChip, AT+i, and Connect One are trademarks of Connect One Ltd.
Copyright  2000–2008 Connect One Ltd. All rights reserved.
Program License Agreement
ii
Warranty Statement
II-EVB-600 User Manual
Warranty Statement
Connect One warrants to the Customer that the Products to be delivered hereunder will function
in accordance with the specifications published with regard thereto by Connect One, under
conditions of normal use and service and when used in accordance with Connect One’s
instructions, for a period of 12 (twelve) months from shipment by Connect One or its distributor
to the customer. Connect One will, at its option, repair or replace Products that fail to perform as
aforesaid. The Customer will ship defective Products to be repaired or replaced to Connect One
under warranty at Connect One’s expense, and Connect One will, at its expense, ship the
repaired Products or its replacement to the Customer.
In no event will Connect One’s liability under the foregoing warranty exceed the purchase price
of the defective Products.
The warranty set forth above will not apply (i) with respect to defects or damage caused by the
use of unauthorized parts, the making of unauthorized repairs or improper use or maintenance,
(ii) if service or repairs of the allegedly defective Products have been performed by persons other
than qualified persons who have been properly trained to perform the same, (iii) if the allegedly
defective Products have been affected by alterations, modifications or other tampering or
misuse, (iv) if the allegedly defective Products have been removed from their original packaging
prior to sale to the end-user or (v) if the allegedly defective Products have been used otherwise
than in accordance with Connect One’s instructions.
The provisions of the above sections set forth the Customer’s sole and exclusive remedies with
regard to Product failure. CONNECT ONE MAKES NO OTHER WARRANTIES, EXPRESSED OR
IMPLIED, WITH RESPECT TO THE PRODUCTS, INCLUDING BUT NOT LIMITED TO ANY WARRANTY
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF
PATENT OR OTHER INTELLECTUAL PROPERTY RIGHTS. THERE ARE NO OTHER WARRANTIES
WITH RESPECT TO THE PRODUCTS ARISING FROM ANY COURSE OF DEALING, USAGE OR
TRADE OR OTHERWISE. IN NO EVENT WILL CONNECT ONE BE LIABLE FOR INDIRECT, SPECIAL
OR CONSEQUENTIAL DAMAGES WHETHER UNDER THIS AGREEMENT, IN TORT OR OTHERWISE,
OR FOR AN AMOUNT IN EXCESS OF THE ACTUAL AMOUNT PAID BY THE CUSTOMER TO
CONNECT ONE FOR THE FAILED PRODUCTS.
Warranty Statement
iii
II-EVB-600 User Manual
Table of Contents
TABLE OF CONTENTS
PROGRAM LICENSE AGREEMENT ......................................................................................................... II
WARRANTY STATEMENT ........................................................................................................................ III
1
2
PRODUCT OVERVIEW .......................................................................................................................... 1
1.1
ICHIP 2064SEC: THE II-EVB-600 INTERNET ENGINE ........................................................................... 1
1.2
HOW TO USE THIS MANUAL .................................................................................................................. 1
GETTING STARTED ............................................................................................................................... 2
2.1
WHAT’S IN THE PACKAGE? ................................................................................................................... 2
2.2
ADDITIONAL DOCUMENTATION ............................................................................................................ 2
2.3
UNPACKING AND INSTALLING ............................................................................................................... 2
2.4
CONNECTORS AND SWITCH POSITIONS .................................................................................................. 4
2.4.1
Connectors..................................................................................................................................... 4
2.4.2
Switches ......................................................................................................................................... 5
2.5
LED POSITIONS ..................................................................................................................................... 5
2.6
JUMPER SETTINGS ................................................................................................................................. 6
2.7
BILL OF MATERIALS .............................................................................................................................. 7
2.8
SCHEMATICS ....................................................................................................................................... 14
2.9
RUNNING THE ICHIPCONFIG UTILITY FOR THE FIRST TIME ................................................................. 24
2.10
3
CONFIGURING FOR CONNECTION ..................................................................................................... 25
2.10.1
Dynamic IP Allocation ............................................................................................................. 26
2.10.2
Fixed IP Configuration ............................................................................................................ 26
FIRMWARE AND PARAMETERS UPDATE .................................................................................... 28
3.1
LOCAL FIRMWARE UPDATE ................................................................................................................. 28
3.1.1
Loading the Firmware from Host ................................................................................................ 28
3.1.2
Loading the Firmware from SPI Flash Memory ......................................................................... 28
3.2
MANAGING PARAMETER FILES ........................................................................................................... 31
3.2.1
Saving the II-EVB-600 Configuration to an RPF File ................................................................ 32
3.2.2
Loading an RPF File ................................................................................................................... 32
Table of Contents
v
II-EVB-600 User Manual
1
Product Overview
Product Overview
Connect One’s II-EVB-600 with its iChip™ CO2064SEC IP-enables and offloads connectivity tasks
from a host processor or host device. II-EVB-600 supports effortless integration of many upper
layer Internet protocols using either AT+i commands or the iChipConfig Utility, both of which are
discussed in this document.
II-EVB-600 features include the ability to stream data over TCP or UDP sockets (up to 10
simultaneous active sockets are available) and manage two listening sockets. In addition, a
secure socket (SSL3/TLS1) is fully supported. Additional features include the ability to send
plain-text e-mails; an FTP client, and the SerialNET (Device Server) mode, a plug-and-play
operating mode that enables the connection of any device with an RS232 interface to the
Internet, without changing anything on the device’s hardware or software.
1.1
iChip 2064SEC: The II-EVB-600 Internet Engine
The host processor communicates with the II-EVB-600 via Connect One’s high-level AT+i™
command set. AT+i commands are simple ASCII characters that are sent across the RS232
interface. The AT+i Application Programming Interface (API) requires writing just a few lines of
code on the host processor to implement Internet connectivity.
AT+i commands make it very easy to configure, test, and implement high-level Internet
protocols with virtually no understanding of TCP/IP or other Internet protocols. Thanks to the
AT+i commands, the device only needs to tell the II-EVB-600 what task to perform, but not how
to perform it. For example, if the device has to send textual e-mail, after a one-time short
configuration of subject, recipient, mail account, etc., the device sends AT+iEOA:<lines of text>.
The iChip inside the II-EVB-600 establishes a connection or uses the existing one, builds the
e-mail (headers and content), connects to the SMTP server, and sends the e-mail. A status
report is sent to the device upon completion. All these actions are completely hidden from the
device and only require sending a few characters in addition to the e-mail content. This mode of
operation is applicable for all features of the II-EVB-600.
1.2
How to Use this Manual
iChipConfig Utility is a front-end Windows-based user interface for the AT+i commands. The
iChipConfig Utility, combined with the II-EVB-600, enables quick and full product configuration,
serial-based updating of firmware, and packaging of a parameters file. This functionality is
achieved from any device, machine, or system.
Note: From this point onward, this manual assumes that you have the iChipConfig Utility
installed. The configuration, running and testing of the II-EVB-600 is demonstrated via the
iChipConfig Utility, although they can also be carried out using AT+i commands. For a complete
description of the AT+i interface and commands, please refer to the AT+i Programmer's Manual
on the Connect One website: http://www.connectone.com.
To set up the iChipConfig Utility, please refer to the iChipConfig Utility User Manual Version
2.4.44 or higher.
The latest version of the iChipConfig Utility can be found on the Connect One website:
http://www.connectone.com.
Product Overview
1
II-EVB-600 User Manual
2
Getting Started
Getting Started
This section describes the content of the II-EVB-600 package, provides additional relevant
documentation to enhance and fine-tune the II-EVB-600 functionality, and includes unpacking
and first-time configuration instructions. The final section of this chapter offers several ways to
test the II-EVB-600 LAN connection.
2.1
What’s in the Package?
The II-EVB-600 is a turnkey boxed solution and, as such, is supplied with all necessary
accessories. The package includes the following items:
2.2

II-EVB-600 evaluation board

RS232 cable

RJ45 Cat 5 100BaseT cable

110V or 220V power supply

Extra iChip CO2064SEC
Additional Documentation
The II-EVB-600 is built around the iChip CO2064SEC. Great flexibility in configuration and
operation of this product can be achieved via proper use of the AT+i commands.
For the sake of simplicity, the II-EVB-600 configuration and operation is described in this
document mainly through the iChipConfig Utility.
The iChipConfig Utility and the iChipConfig Utility User Manual can be downloaded from the
Connect One website.
Note: Because documentation, utilities and firmware files change from time to time, please be
sure to check for the latest version on the Connect One website: http://www.connectone.com.
2.3
Unpacking and Installing
The II-EVB-600 installation is simple and all the required accessories are supplied with the
device.
The II-EVB-600 is provided pre-configured to work with LAN using COM1 on the
II-EVB-600 as host interface. For additional configuration options, see section 2.5 Jumper
Settings.
➣ To install the II-EVB-600 and connect it to a LAN network:
1
Getting Started
Connect the RJ45 cable to the II-EVB-600 RJ45 port. Connect the other end of
the cable to a 10/100BaseT or 100BaseT Ethernet switch or hub.
2
II-EVB-600 User Manual
Getting Started
2
Connect one side of the RS232 cable to the II-EVB-600 RS232 COM1 port and
the other side to your device or PC’s COM port.
3
Connect the power supply to the DC jack on the II-EVB-600 and apply power.
The Link LED (orange) on the RJ45 should now be on and the Activity LED
(green) should blink occasionally, reflecting network traffic.
To test the connection, use AT+i commands or the iChip Config Utility to invoke any of the
activities that trigger the iChip to go online and use the Internet or local LAN.
Getting Started
3
II-EVB-600 User Manual
Getting Started
2.4
Connectors and Switch Positions
2.4.1
Connectors
Name
Type
Function
1
J2A
HEADER 17X2
CO2128 EXTENSION
2
J2B
HEADER 13X2
CO2128 EXTENSION
3
J2C
HEADER 17X2
CO2128 EXTENSION
4
J2D
HEADER 13X2
CO2128 EXTENSION
5
J1
HEADER 20X2
EBI BUS (for CO2128)
6
J2
HEADER 20X2
EBI BUS (for CO2128)
7
J4
HEADER 10X2
HPI (for CO2128)
8
J5
DB9 – FEMALE
COM0 (for CO2128)
9
J6
HEADER 5X2
SSC (for CO2128)
10
J7
RJ11
Telephone Line (from Uart1)
11
J8
DB9 –MALE
COM1
12
J9
RJ45
10/100BaseT
13
J10
HEADER 4X1
TWI
14
J11
SIM CARD
SIM CARD
15
J12
HEADER 6X1
SPI1
13
J13
HEADER 6X1
SPI0
14
J14
DB9 – FEMALE
COM2
15
J15
USB-A
USB Host
16
J16
DC-JACK
POWER Supply
17
J17
USB-B
USB Device
18
J18
BLOCK 2 Pin
Analog Input
19
J19
HEADER 8X2
MII EXTENSION
20
J20
HEADER 5X2
MII EXTENSION
Getting Started
4
II-EVB-600 User Manual
2.4.2
2.5
Getting Started
Switches
Name
Type
Function
1
SW1
PUSH BOTTOM
MSEL
2
SW2
PUSH BOTTOM
RESET
3
SW3
TOGGLE SWITCH
POWER On/Off
LED Positions
Getting Started
Name
Type
Function
1
D1
G.LED
RXD0
2
D2
G.LED
TXD0
3
D3
G.LED
DTR1
4
D4
G.LED
CD1
5
D5
G.LED
RXD1
6
D6
G.LED
TXD1
7
D7
G.LED
RXD2
8
D8
G.LED
TXD2
9
D9
R.LED
iChip Error
10
D13
G.LED
FW_RDY
11
D14
R.LED
3V VDDIO
12
D17
G.LED
DATA READY
13
D19
R.LED
5V For USB Host
14
D20
R.LED
1.2V
5
II-EVB-600 User Manual
2.6
Getting Started
Jumper Settings
Name
Setting
1
JP2
1-2 ONREG Pin=0 working with external VDD core ; 2-3 ONREG
Pin=1 working with internal VDD core
2
JP3
ON –External VDDCore (For CO2064)
3
JP5
ON –External VDDCore (For CO2128)
4
JP6
ON- Enable 1K Pull-up Resistor On HPI_nWAIT signal.
(HPI_Wait_Enable For CO2128)
5
JP7
ON- Enable COM0 (only when HPI is disable) (For CO2128)
6
JP8
ON – Power to J6 Connector (SSC) (For CO2128)
7
JP9
ON- Enable HPI (For CO2128)
8
JP10
ON- Enable Socket Modem (on Uart1)
9
JP11
ON- Enable COM1
10
JP12
ON – Power to J10 Connector (TWI)
11
JP13
ON- Enable 1K Pull-up Resistor On TWI_TWD signal.
12
JP14
ON- Enable 1K Pull-up Resistor On TWI_TWCK signal.
13
JP15
ON- Enable SIM CARD
14
JP16
ON- SIM Card 3V ; OFF SIM Card 5V
15
JP17
ON- Enable SIM Card Interrupt .
16
JP18
ON – Power to J12 Connector (SPI1)
17
JP19
ON – Power to J13 Connector (SPI0)
18
JP20
ON – Enable SPI1 Flash
19
JP21
1-2 = COM0+ssc ; 2-3 = HPI
20
JP22
1-2 = MII ; 2-3 = RMII+COM1
21
JP23
1-2 = S.C ; 2-3 = SPI0
22
JP24
1-2 = SPI1 ; 2-3 = TWI
23
JP25
1-2 = LAN_EN ; 2-3 = LAN_DIS;
24
JP26
1-2 = BYPASS Rom ;2-3 = ENGAGE Rom
Getting Started
6
II-EVB-600 User Manual
Getting Started
25
JP27
1-2 = UHP_EN ; 2-3 = UHP_DIS
26
JP28
ON – COM2 Enable COM2_EN
27
JP29
ON – Enable Parallel Flash (For CO2128)
2.7
Bill of Materials
Part Description
Designation
Quantity
Electromagnetic Sound Transducer/RoHS
LS1
1
Capacitor 1nF/3KV, Size 7mm
C53-C54
2
Capacitor 1uF/16V, TANTALOM, Case A
C107
1
Capacitor 1uF/16V, TANTALOM, Case A
C80
1
Capacitor 1uF/16V, TANTALOM, Case A
C109
1
Capacitor 1uF/16V, TANTALOM, Case A
C35-C36
2
Capacitor 1uF/16V, TANTALOM, Case A
C39
1
Capacitor 10uF/16V,TANTALOM,Case B/RoHS
C88
1
Capacitor 10uF/16V,TANTALOM,Case B/RoHS
C108
1
Capacitor 10uF/16V,TANTALOM,Case B/RoHS
C42
1
Capacitor 10uF/16V,TANTALOM,Case B/RoHS
C56
1
Capacitor 10uF/16V,TANTALOM,Case B/RoHS
C58
1
Capacitor 10uF/16V,TANTALOM,Case B/RoHS
C20
1
Capacitor 10uF/16V,TANTALOM,Case B/RoHS
C79
1
Capacitor 10uF/16V,TANTALOM,Case B/RoHS
C113
1
Capacitor 10uF/16V,TANTALOM,Case B/RoHS
C92
1
Capacitor 15pF
C100-C101
2
Capacitor 22pF
C33-C34
2
Getting Started
7
II-EVB-600 User Manual
Getting Started
Capacitor 47pF
C104
1
Capacitor 47pF
C94-C95
2
Capacitor 100nF, Size 0603
C71-C78
8
Capacitor 100nF, Size 0603
C81-C82
2
Capacitor 100nF, Size 0603
C86
1
Capacitor 100nF, Size 0603
C90-C91
2
Capacitor 100nF, Size 0603
C98-C99
2
Capacitor 100nF, Size 0603
C18
1
Capacitor 100nF, Size 0603
C110-C112
3
Capacitor 100nF, Size 0603
C22-C32
11
Capacitor 100nF, Size 0603
C37
1
Capacitor 100nF, Size 0603
C41
1
Capacitor 100nF, Size 0603
C43-C44
2
Capacitor 100nF, Size 0603
C49-C52
4
Capacitor 100nF, Size 0603
C55
1
Capacitor 100nF, Size 0603
C57
1
Capacitor 100nF, Size 0603
C59-C60
2
Capacitor 100nF, Size 0603
C102-C103
2
Capacitor 100nF, Size 0603
C65-C68
4
Capacitor 100nF, Size 0603
C105-C106
2
Capacitor 100uF/10V TANTALOM Case D
C69-C70
2
Capacitor 470nF
C93
1
Capacitor 470nF
C61-C64
4
Capacitor 470nF
C87
1
Capacitor 470nF
C45-C48
4
Getting Started
8
II-EVB-600 User Manual
Getting Started
Capacitor 470nF
C83-C85
3
Capacitor 1000uF/25V Electrolytic/RoHS
C96-C97
2
iChipSec CO2128, 128pin LQFP, 3.3v, 48MHz, RoHS
U1B
1
D-Sub Right Angle, Female 9 pin Connector/RoHS
J5
1
D-Sub Right Angle, Female 9 pin Connector/RoHS
J14
1
D-Sub Right Angle, Male 9 pin Connector/RoHS
J8
1
Connector DC-JACK 2.1mm/RoHS
J16
1
ABS UL94-V0; 0.46m/m DIA
J7
1
RJ45 10/100BaseT Magnetics/RoHS
J9
1
CON SIM/SMA Holder/RoHS
J11
1
CONN TERMINAL BLOCK 2POS 5mm PCB/RoHS
J18
1
CONN USB FEMALE TYPE A PCB
J15
1
CONN USB FEMALE TYPE B PCB
J17
1
Crystal Clock 12 MHz/RoHS
Y2
1
1.0 AMP SILICON RECTIFIERS DIODE/RoHS
D10
1
DIA SURGE SUPPRESSOR (DSS)
RV1
1
FAST SWITCHING SURFACE MOUNT DIODE/RoHS
D15-D16
2
FAST SWITCHING SURFACE MOUNT DIODE/RoHS
D12
1
Ultrafast Rectifiers 1.0A ;50V-600V/RoHS
D11
1
Header 2mm Pitch SQ Tail Socket
2pin,Female/RoHS
U8A
1
HEADER 2x1 / MALE 100 MIL PITCH
J20
1
HEADER 2x1 / MALE 100 MIL PITCH
JP5-JP7
3
HEADER 2x1 / MALE 100 MIL PITCH
JP13-JP17
5
HEADER 2x1 / MALE 100 MIL PITCH
JP9-Jp11
3
Getting Started
9
II-EVB-600 User Manual
Getting Started
HEADER 2x1 / MALE 100 MIL PITCH
JP28-JP29
2
HEADER 3x1 / MALE 100 MIL PITCH
JP2
1
HEADER 3x1 / MALE 100 MIL PITCH
JP21-JP27
7
Header 2mm Pitch SQ Tail Socket
4pin,Female/RoHS
U8D
1
HEADER 4x1 / MALE 100 MIL PITCH
J10
1
HEADER 5x2 / MALE 100 MIL PITCH
J20
1
HEADER 5x2 / MALE 100 MIL PITCH
J6
1
HEADER 6x1 / MALE 100 MIL PITCH
J12
2
HEADER 8x2 / MALE 100 MIL PITCH
J19
1
Header 2mm Pitch SQ Tail Socket
9pin,Female/RoHS
U8B-U8c
2
HEADER 10x2 /MALE 100 MIL PITCH
J4
1
HEADER 20x2/FEMALE100 MIL PITCH/RoHS
J1-J2
2
Low Power High Speed Rail to Rail Amp/RoHS
U23
1
Low Power High Speed Rail to Rail Amp/RoHS
U26
1
Low Voltage Audio Power Amplifier/RoHS
U9
1
SDPT Analog Switch/RoHS
U22
1
1A Step-Down Regulator;Out-3.3v/RoHS
U21
1
8 MBIT,Buttom-Boot 3v Flash/RoHS
U2
1
4Mbit 3.3V Serial Flash with SPI Interface/RoHS
U16
1
IC Buffer/Ldriver Octal/RoHS
U7
1
IC Buffer/Ldriver Octal/RoHS
U18
1
IC Buffer/Ldriver Octal/RoHS
U12
1
Octal Buffers/Drivers With 3-State Outputs
U10
1
Octal Buffers/Drivers With 3-State Outputs
U6
1
Getting Started
10
II-EVB-600 User Manual
Getting Started
3V Octal Bidirectional Transceiver/RoHS
U5
1
IC SINGLE INVERTER GATE / RoHS
U3
1
10/100 PHY CONTROLLER/RoHS
U14
1
100mA Low-Drop Regulator 1.2v/RoHS
U20
1
Adjustable 1.5A LDO Voltage Regulator
U19
1
RS232, 3 Driver/5 Receiver 3v/5v,Ind/RoHS
U4
1
RS232, 3 Driver/5 Receiver 3v/5v,Ind/RoHS
U17
1
RS232, 3 Driver/5 Receiver 3v/5v,Ind/RoHS
U11
1
3v/3.3v Micro Supervisory Circuit, Ind/RoHS
U24
1
Smart Card Interface/RoHS
U15
1
Temp Sence/RoHS
U27
1
Indactor Unshiled 68uH 1.1A SMT/RoHS
L4
1
BK2125-102/RoHS
L2
1
BK2125-102/RoHS
L9-L12
4
Wound Beads,Turns:2x1.5; Wire:0.53 24
AWG/RoHS
L1
1
2mm Plastic Female Jumper 2pin/RoHS
JP2
1
2mm Plastic Female Jumper 2pin/RoHS
JP5-JP7
3
2mm Plastic Female Jumper 2pin/RoHS
JP13-Jp17
5
2mm Plastic Female Jumper 2pin/RoHS
JP9-JP11
3
2mm Plastic Female Jumper 2pin/RoHS
JP20-JP29
10
LED-GREEN 3mm
D17
1
LED-GREEN 3mm
D1-D8
8
LED-GREEN 3mm
D14
1
LED-RED 3mm
D13
1
Getting Started
11
II-EVB-600 User Manual
Getting Started
LED-RED 3mm
D19-D20
2
Oscillator Clock 50MHz, SMD,Ind/RoHS
U13
1
POLYSWITCH RXE Series 0.30A Hold/RoHS
F1
1
Potentiometer 10K Ohm / RohS
P1
1
Resistor 0 Ohm 10%
R87
1
Resistor 0 Ohm 10%
R85
1
Resistor 0 Ohm 10%
R149
1
Resistor 0 Ohm 10%
R94
1
Resistor 0 Ohm 10%
R136
1
Resistor 0 Ohm 10%
R50
1
Resistor 2 Ohm 10%
R68-R69
2
Resistor 3K
R135
1
Resistor 3K
R106-R112
7
Resistor 3K
R117
1
Resistor 4.7K 10%
R131
1
Resistor 6.8K 1%
R86
1
Resistor 10 Ohm 10%
R70
1
Resistor 10K 1%
R65
1
Resistor 10K 1%
R90-R93
4
Resistor 10K 1%
R62
1
Resistor 10K 1%
R78-R80
3
Resistor 10K 1%
R145-R146
2
Resistor 15k
R122
1
Resistor 15k
R126
1
Resistor 15k
R120
1
Getting Started
12
II-EVB-600 User Manual
Getting Started
Resistor 27 Ohm 10%
R119
1
Resistor 27 Ohm 10%
R121
1
Resistor 27 Ohm 10%
R123-R124
2
Resistor 33 Ohm 10%
R7-R48
42
Resistor 49.9 Ohm 1%
R81-R84
4
Resistor 100 Ohm 10%
R116
1
Resistor 100K 10%
R63
1
Resistor 100K 10%
R98
1
Resistor 100K 10%
R53-R61
9
Resistor 100K 10%
R71-R73
3
Resistor 100K 10%
R115
1
Resistor 100K 10%
R51
1
Resistor 300 Ohm 10%
R118
1
Resistor 470 Ohm 10%
R128
1
Resistor 470 Ohm 10%
R88-R89
2
Resistor 470 Ohm 10%
R130
1
Resistor 470 Ohm 10%
R134
1
Resistor 470 Ohm 10%
R143
1
Resistor 470 Ohm 10%
R66-R67
2
Resistor 470 Ohm 10%
R113-R114
2
Resistor 470 Ohm 10%
R147
1
Resistor 470 Ohm 10%
R74-R77
4
TOGEL SW ON/OFF-SPDT-90D/RoHS
SW3
1
SW-TACK/RoHS
SW1-SW2
2
Getting Started
13
II-EVB-600 User Manual
2.8
Getting Started
Schematics
Getting Started
14
5
4
3
2
VDDCOREA
VDD
U1.9
U1.23
U1.41
U1.54
U1.13
+
C1
100NF
D
1
U1.10
C2
100NF
U1.24
U1.42
GND
C3
100NF
C4
100NF
U1.33
U1.52
C20
C17
+
C5
100NF
10UF/16V
U1.55
U1.14
C6
100NF
U1.34
C7
100NF
10UF/16V
D
U1.53
GND
BK2125HM601
VREF
ADVREF
L8
C13
100NF
VDDPLLA
VDDCOREA
BK2125HM601
AGND
L5
VDD
VDDCOREA
1
VDD AVDD
2
EXT_VDDCORE
JP3
3
ONREG
C14
100NF
2
GND
1
VDDPLLA
C
JMP3
JP2
C
GND
GND
2
1
22PF
19
RES
DDM
DDP
11
12
DDM
DDP
HDM
HDP
15
16
HDM
HDP
HPID5_ADC
8
HPID6_SCLK0
17
PIOC7
FW_RDY
MSEL
ICHIP_ERR
DATA_READY_FIQ
IRQ0
TXD2
RXD2
25
26
27
28
20
21
22
F/W_RDY/TCLK0/PIOC22
MSEL/TIOA0/PIOC23
iChip_ERROR/TIOB0/PIOC24
DATA_RDY/FIQ/PIOC25
IRQ0/PIOC26
TXD2/PIOC27
RXD2/PIOC28
64
18
LFT
TST
B
C19
R1
TBD
TBD
ADC/PIOC6
54
41
23
9
5
SPI0_MISO/SC_CLK/PIOC14
SPI0_MOSI/SC_C8/PIOC15
SPI0_SPCLK/SC_C4/PIOC16
SPI0_CS/SC_RST/PIOC17
SPI1_MISO/SC_IO/PIOC18
SPI1_MOSI/SC_INTB/PIOC19
SPI1_CLK/I2C_TWD/PIOC20
SPI1_CS/I2C_TWCK/PIOC21
56
57
58
59
60
61
62
63
SPI0MISO_SCCLK
SPI0MOSI_SCC8
SPI0CLK_SCC4
SPI0CS_SCRST
SPI1MISO_SCIO
SPI1MOSI_SCINTB
SPI1CLK_I2CTWD
SPI1CS_I2CTWCK
MII_ERXCK/RXD1/PIOB12
MII_ETX2/DTR1/PIOB13
MII_ETX3/DCD1/PIOB14
MII_ETXER/TXD1/PIOB15
MII_ERX2/DSR1/PIOB16
MII_ERX3/RI1/PIOB17
MII_ECRS/CTS1/PIOB18
MII_ECOL/RTS1/PIOB19
MII_ETXCK/RMII_REFCLK/PIOB20
MII_ETXEN/PIOB21
MII_ETX0/PIOB22
MII_ETX1/PIOB23
MII_ERXDV/RMII_CRSDV/PIOB24
MII_ERX0/PIOB25
MII_ERX1/PIOB26
MII_ERXER/PIOB27
MII_EMDC/PIOB28
MII_EMDIO/PIOB29
29
30
31
32
35
36
37
38
39
40
43
44
45
46
47
48
49
50
ERXCK_RXD1
ETX2_DTR1
ETX3_DCD1
ETXER_TXD1
ERX2_DSR1
ERX3_RI1
ECRS_CTS1
ECOL_RTS1
EREFCK
ETXEN
ETX0
ETX1
CRSDV
ERX0
ERX1
ERXER
EMDC
EMDIO
IRQ1/RMII_EF100/PIOB30
51
IRQ1
XIN
XOUT
-RESET
VDDCORE
VDDCORE
VDDCORE
VDDCORE
Y1
C16
VDDPLL
52
33
13
4
7
AVDD
VREF
12MHz
22PF
VDDIO
VDDIO
VDDIO
C15
GND
ONREG
U1A
6
GND
B
A
CPU 2064
55
42
24
10
CO2064
AGND
GND
3
GND
53
34
14
A
GNDIO
GNDIO
GNDIO
R2
0
TBD
GNDCORE
GNDCORE
GNDCORE
GNDCORE
C21
Title
IIEVB-600
GND
5
AGND
4
GND
3
2
Size
B
Document Number
Date:
Tuesday, January 30, 2007
Rev
1.1
Sheet
1
1
of
9
5
4
3
VDDCOREB
2
EXT_VDDCORE
VDD
JP5
1
1
VDDCOREB
U1.11
U1.31
U1.41
U1.67
U1.91
U1.102
U1.50
U1.82
U1.111
U1.120
2
C113
+
VDD
VDDPLLB
C26
100NF
AVDD
C27
100NF
C28
100NF
C29
100NF
C30
100NF
C22
100NF
C31
100NF
ONREG
U1.12
D
U1.32
-RESET
EBI_nRD_nOE
EBI_nWR0
EBI_nWR1_nUB
EBI_nCS0
EBI_nWAIT
EBI_CS1/A20
RES
DDM
DDP
DDM
DDP
29
30
DDM
DDP
HDM
HDP
HDM
HDP
33
34
HDM
HDP
R7
R8
R9
R10
R11
R12
R13
R14
R15
R16
R17
R18
R19
R20
R21
R22
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
42
43
44
45
47
48
49
52
53
54
55
56
57
58
75
76
EBI_A0
EBI_A1
EBI_A2
EBI_A3
EBI_A4
EBI_A5
EBI_A6
EBI_A7
EBI_A8
EBI_A9
EBI_A10
EBI_A11
EBI_A12
EBI_A13
EBI_A14
EBI_A15
EBI_A16
EBI_A17
EBI_A18
EBI_A19
R23
R24
R25
R26
R27
R28
R29
R30
R31
R32
R33
R34
R35
R36
R37
R38
R39
R40
R41
R42
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
33
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
77
78
79
80
81
84
85
86
87
88
89
90
104
105
106
107
108
109
110
113
EBI_nRD_nOE
EBI_nWR0
EBI_nWR1_nUB
R43
R44
R45
33
33
33
nRD 114
nWR 115
BHE 116
EBI_nCS0
EBI_nWAIT
R46
R47
33
33
nCS0 117
nWAIT118
EBI_CS1/A20
R48
33 CS1_A20 119
EBI_A0/NLB/PIOA16
EBI_A1/PIOA17
EBI_A2/PIOA18
EBI_A3/PIOA19
EBI_A4/PIOA20
EBI_A5/PIOA21
EBI_A6/PIOA22
EBI_A7/PIOA23
EBI_A8/PIOA24
EBI_A9/PIOA25
EBI_A10/PIOA26
EBI_A11/PIOA27
EBI_A12/PIOA28
EBI_A13/PIOA29
EBI_A14/PIOA30
EBI_A15/PIOB0
EBI_A16/PIOB1
EBI_A17/PIOB2
EBI_A18/PIOB3
EBI_A19/PIOB4
EBI_RD/EBI_OE/PIOB5
EBI_RW0/EBI_WE/PIOB6
EBI_RW1/EBI_UB/PIOB7
EBI_CS0/PIOB8
EBI_WAIT/PIOB9
AVDD
HPI_WAIT/ERR/SSC_RD/PIOC0
HPI_D0/SSC_TD/PIOC1
HPI_D1/SSC_TK/PIOC2
HPI_D2/SSC_RK/PIOC3
HPI_D3/SSC_TF/PIOC4
HPI_D4/SSC_RF/PIOC5
HPI_D5/ADC/PIOC6
10
HPID5_ADC
HPI_D6/SCLK0/PIOC7
HPI_D7/RTS0/PIOC8
HPI_RD/DSR0/PIOC9
HPI_WR/CTS0/PIOC10
HPI_CS/RXD0/PIOC11
HPI_IBF/DTR0/PIOC12
HPI_OBE/TXD0/PIOC13
35
23
24
25
26
27
28
HPID6_SCLK0
HPID7_RTS0
HPIRD_DSR0
HPIWR_CTS0
HPICS_RXD0
HPIIBF_DTR0
HPIOBE_TXD0
SPI0_MISO/SC_CLK/PIOC14
SPI0_MOSI/SC_C8/PIOC15
SPI0_SPCLK/SC_C4/PIOC16
SPI0_CS/SC_RST/PIOC17
SPI1_MISO/SC_IO/PIOC18
SPI1_MOSI/SC_INTB/PIOC19
SPI1_CLK/I2C_TWD/PIOC20
SPI1_CS/I2C_TWCK/PIOC21
122
123
124
125
126
127
128
1
F/W_RDY/TCLK0/PIOC22
MSEL/TIOA0/PIOC23
iChip_ERROR/TIOB0/PIOC24
DATA_RDY/FIQ/PIOC25
IRQ0/PIOC26
TXD2/PIOC27
RXD2/PIOC28
59
60
61
62
38
39
40
MII_ERXCK/RXD1/PIOB12
MII_ETX2/DTR1/PIOB13
MII_ETX3/DCD1/PIOB14
MII_ETXER/TXD1/PIOB15
MII_ERX2/DSR1/PIOB16
MII_ERX3/RI1/PIOB17
MII_ECRS/CTS1/PIOB18
MII_ECOL/RTS1/PIOB19
MII_ETXCK/RMII_REFCLK/PIOB20
MII_ETXEN/PIOB21
MII_ETX0/PIOB22
MII_ETX1/PIOB23
MII_ERXDV/RMII_CRSDV/PIOB24
MII_ERX0/PIOB25
MII_ERX1/PIOB26
MII_ERXER/PIOB27
MII_EMDC/PIOB28
MII_EMDIO/PIOB29
IRQ1/RMII_EF100/PIOB30
R50
0
CO2128
GNDCORE
GNDCORE
GNDCORE
GNDCORE
NC
NC
NC
NC
SPI0MISO_SCCLK
SPI0MOSI_SCC8
SPI0CLK_SCC4
SPI0CS_SCRST
SPI1MISO_SCIO
SPI1MOSI_SCINTB
SPI1CLK_I2CTWD
SPI1CS_I2CTWCK
L12
U1.5
ERXCK_RXD1
ETX2_DTR1
ETX3_DCD1
ETXER_TXD1
ERX2_DSR1
ERX3_RI1
ECRS_CTS1
ECOL_RTS1
EREFCK
ETXEN
ETX0
ETX1
CRSDV
ERX0
ERX1
ERXER
EMDC
EMDIO
101
IRQ1
9
EREFCK
ECRS_CTS1
ERX2_DSR1
ETX3_DCD1
ERXCK_RXD1
GND
25
23
21
19
17
15
13
11
9
7
5
3
1
nWAIT
BHE
nRD
A18
A16
A14
A12
GND
GND
EMDIO
ERXER
ERX0
ETX1
A11
A9
A7
A5
A3
A1
D15
C18
100NF
GND
ETXEN
ECOL_RTS1
ERX3_RI1
ETXER_TXD1
ETX2_DTR1
26
24
22
20
18
16
14
12
10
8
6
4
2
CS1_A20
nCS0
nWR
A19
A17
A15
A13
HEADER 17X2
SPI1CS_I2CTWCK
SPI1MOSI_SCINTB
SPI0CS_SCRST
SPI0MOSI_SCC8
C
J2B
GND
ICHIP_ERR
FW_RDY
D12
D10
D8
D6
D4
D2
D0
TXD2
HEADER 13X2
25
23
21
19
17
15
13
11
9
7
5
3
1
26
24
22
20
18
16
14
12
10
8
6
4
2
D13
D11
D9
D7
D5
D3
D1
GND
DATA_READY_FIQ
MSEL
RXD2
HEADER 13X2
C35
1UF/16V
VDD
+
B
C36
VDD
1UF/16V
J2A
33
31
29
27
25
23
21
19
17
15
13
11
9
7
5
3
1
-RESET
HPID6_SCLK0
HDM
DDM
HPIIBF_DTR0
HPIWR_CTS0
HPID7_RTS0
HPID3_SSCTF
HPID1_SSCTK
HPInWAITERR_SSCRD
ADVREF
AGND
ADVREF
BK2125HM601
L10
C37
34
32
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
GND
IRQ0
HDP
DDP
HPIOBE_TXD0
HPICS_RXD0
HPIRD_DSR0
HPID4_SSCRF
HPID2_SSCRK
HPID0_SSCTD
HPID5_ADC
AVDD
VDD
100NF
HEADER 17X2
A
CPU 2128 + EXTENSION
AGND
+
C39
1UF/16V
GND
Title
IIEVB-600
Size
B
Document Number
Date:
Tuesday, January 30, 2007
Rev
1.1
GND
GND
5
34
32
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
J2D
SPI1CLK_I2CTWD
SPI1MISO_SCIO
SPI0CLK_SCC4
SPI0MISO_SCCLK
TBD
GND
AGND
4
D
L9
33
31
29
27
25
23
21
19
17
15
13
11
9
7
5
3
1
A10
A8
A6
A4
A2
A0
D14
BK2125HM601
AGND
FW_RDY
MSEL
ICHIP_ERR
DATA_READY_FIQ
IRQ0
TXD2
RXD2
63
64
65
66
69
70
71
72
73
74
93
94
95
96
97
98
99
100
13
14
15
16
C32
100NF
112
83
51
12
C40
AGND
TBD
LFT
TST
5
2
36
121
103
92
68
46
32
A
GNDIO
GNDIO
GNDIO
GNDIO
GNDIO
GNDIO
R49
VDD
L11
BK2125HM601
ADVREF
C38
U1.112
VDDPLLB
VDDCOREB
BK2125HM601
IRQ1
EMDC
ERX1
CRSDV
ETX0
U1.6
HPInWAITERR_SSCRD
HPID0_SSCTD
HPID1_SSCTK
HPID2_SSCRK
HPID3_SSCTF
HPID4_SSCRF
EBI_CS1/EBI_A20/PIOB10
U1.83
10UF/16V
J2C
17
18
19
20
21
22
EBI_D0/PIOA0
EBI_D1/PIOA1
EBI_D3/PIOA2
EBI_D3/PIOA3
EBI_D4/PIOA4
EBI_D5/PIOA5
EBI_D6/PIOA6
EBI_D7/PIOA7
EBI_D8/PIOA8
EBI_D9/PIOA9
EBI_D10/PIOA10
EBI_D11/PIOA11
EBI_D12/PIOA12
EBI_D13/PIOA13
EBI_D14/PIOA14
EBI_D15/PIOA15
U1.51
C25
100NF
U1.121
111
82
50
11
7
VDDPLL
6
AVDD
VDDIO
VDDIO
VDDIO
VDDIO
VDDIO
VDDIO
XIN
XOUT
37
EBI_D0
EBI_D1
EBI_D2
EBI_D3
EBI_D4
EBI_D5
EBI_D6
EBI_D7
EBI_D8
EBI_D9
EBI_D10
EBI_D11
EBI_D12
EBI_D13
EBI_D14
EBI_D15
TBD
U1.103
C24
100NF
GND
VDDCORE
VDDCORE
VDDCORE
VDDCORE
4
3
22PF
EBI_D[0..15]
8
ONREG
22PF
C34 GND
GND
120
102
91
67
41
31
U1B
Y2
B
U1.92
+
12MHz
GND
EBI_A[0..19]
U1.68
GND
C33
C
U1.46
C23
100NF
GND
3
2
Sheet
1
2
of
9
5
4
3
2
1
EBI_D[0..15]
EBI_A[0..19]
D
D
J1
R51
100K
JP29
EBI_nCS0
EBI_nCS0 1
2
JUMPER
EBI_nWR0
EBI_nRD_nOE
EBI_nWR0
EBI_nRD_nOE
VDD
B
EBI_D0
EBI_D1
EBI_D2
EBI_D3
EBI_D4
EBI_D5
EBI_D6
EBI_D7
EBI_D8
EBI_D9
EBI_D10
EBI_D11
EBI_D12
EBI_D13
EBI_D14
EBI_D15
VDD
C112
100NF
U3
GND
4
2
EBI_CS1/A20
NC7S04
C
HEADER 20X2 FEM
GND
GND
J2
26
11
28
CE
WE
OE
47
12
BYTE
RESET
RY/BY
29LV800TT-70EC
29
31
33
35
38
40
42
44
30
32
34
36
39
41
43
45
EBI_D14
EBI_D12
EBI_D10
EBI_D8
EBI_A1
EBI_A3
EBI_A5
EBI_A7
EBI_A9
EBI_A11
EBI_A13
EBI_A15
EBI_A17
EBI_nCS1
EBI_D6
EBI_D4
EBI_D2
EBI_D0
5
37
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15/A1
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
HPICS_RXD0
HPIWR_CTS0
HPIRD_DSR0
HPID6_SCLK0
ERXCK_RXD1
ECRS_CTS1
ERX2_DSR1
IRQ0
SPI0MOSI_SCC8
SPI0CS_SCRST
ICHIP_ERR
ERX3_RI1
-RESET
15
GND
GND
VDD
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
46
27
C
25
24
23
22
21
20
19
18
8
7
6
5
4
3
2
1
48
17
16
VCC
U2
EBI_A1
EBI_A2
EBI_A3
EBI_A4
EBI_A5
EBI_A6
EBI_A7
EBI_A8
EBI_A9
EBI_A10
EBI_A11
EBI_A12
EBI_A13
EBI_A14
EBI_A15
EBI_A16
EBI_A17
EBI_A18
EBI_A19
GND
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
3
VDD
C41
100NF
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
EBI_D15
EBI_D13
EBI_D11
EBI_D9
EBI_A0
EBI_A2
EBI_A4
EBI_A6
EBI_A8
EBI_A10
EBI_A12
EBI_A14
EBI_A16
EBI_A18
EBI_D7
EBI_D5
EBI_D3
EBI_D1
TSOP48
GND
EBI_nWR1_nUB
EBI_nRD_nOE
EBI_nCS0
EBI_nWR1_nUB
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
HPIOBE_TXD0
HPID7_RTS0
HPIIBF_DTR0
MSEL
ETXER_TXD1
ECOL_RTS1
ETX2_DTR1
DATA_READY_FIQ
SPI0MISO_SCCLK
SPI0CLK_SCC4
EBI_nWAIT
RESET
IRQ1
EBI_A19
EBI_nWR0
EBI_CS1/A20
B
FW_RDY
HEADER 20X2 FEM
VDD
C42
10UF/16V
+
GND
A
A
EBI BUS + PARALLEL FLASH (OMLY FOR CO2128)
Title
IIEVB-600
5
4
3
2
Size
B
Document Number
Date:
Tuesday, January 30, 2007
Rev
1.1
Sheet
1
3
of
9
5
4
3
2
1
VDD
VDD
C43
100NF
GND
VDD
HPI INTERFACE
C2+
HPIOBE_TXD0
HPIIBF_DTR0
HPID7_RTS0
HPICS_RXD0
HPIRD_DSR0
HPIWR_CTS0
2
26
V-
C45
100NF
GND
C47
470NF
GND
C2-
TXD0
-DTR0
-RTS0
14
13
12
TIN1
TIN2
TIN3
RXD0
-DSR0
-CTS0
20
19
18
17
16
15
ROUT2B
ROUT1
ROUT2
ROUT3
ROUT4
ROUT5
TOUT1
TOUT2
TOUT3
RIN1
RIN2
RIN3
RIN4
RIN5
9
10
11
TXD0232
-DTR0232
-RTS0232
4
5
6
7
8
RXD0232
-DSR0232
-CTS0232
-DTR0232
TXD0232
-CTS0232
RXD0232
-RTS0232
-DSR0232
GND
FORCEON
22
FORCEOFF
SP3243ECA
R63
100K
C
INVALID
21
GND
23
18
17
16
15
14
13
12
11
B1
B2
B3
B4
B5
B6
B7
B8
20 GND
U5
VCC A1 2
A2 3
A3 4
A4 5
A5 6
A6 7
A7 8
A8 9
DIR
OE
1
19
100K
R53
100K
R54
100K
R55
100K
R56
100K
R57
100K
R58
100K
R59
100K
R60
100K
R61
1
3
5
7
9
11
13
15
17
19
HOST_D0
HOST_D2
HOST_D4
HOST_D6
HOST_CS
HOST_WR
HOST_IBF
HOST_D0
HOST_D1
HOST_D2
HOST_D3
HOST_D4
HOST_D5
HOST_D6
HOST_D7
2
4
6
8
10
12
14
16
18
20
HOST_D1
HOST_D3
HOST_D5
HOST_D7
HOST_RD
HOST_WAIT
HOST_OBE
D
J4
HOST_RD
HPICS_RXD0
HEADER 10x2
GND
74HCT245
VDD
GND
10
R62
10K
GND
VDD
GND
25
ENABLE_RS0232
J5
1
6
2
7
3
8
4
9
5
HPID0_SSCTD
HPID1_SSCTK
HPID2_SSCRK
HPID3_SSCTF
HPID4_SSCRF
HPID5
HPID6_SCLK0
HPID7_RTS0
RS232 TO COM0
1
C48
470NF
27
3
DB9 FEM
C1-
V+
11
D
C1+
24
C44
10
28
C46
470NF
470NF
VCC
U4
C
C49
100NF
GND
U6
20
GND
HPInWAITERR_SSCRD
2
HOST_RD
HOST_WR
nHPI_CONTROL
JUMPER
HPIIBF_DTR0
HPIOBE_TXD0
HOST_CS
GND
VDD
VDD
C50
100NF
10K
VDD
GND
R65
VCC
1A1
1Y1
1A2
1Y2
1A3
1Y3
1A4
1Y4
18
16
14
12
11
13
15
17
2A1
2A2
2A3
2A4
9
7
5
3
1
19
1OE
2OE
2
4
6
8
1
19
HPIRD_DSR0
HPIWR_CTS0
HOST_OBE
HPICS_RXD0
HPICS_RXD0
2Y1
2Y2
2Y3
2Y4
9
7
5
3
JUMPER
GND
1
18
16
14
12
JP8
JUMPER
JP9
2
2A1
2A2
2A3
2A4
HOST_WAIT
B
1Y1
1Y2
1Y3
1Y4
2
11
13
15
17
2
HOST_IBF
20
VCC
nENABLE_RS0233
R66
R67
470
1G
2G
D1
G.LED
D2
G.LED
1
74LVX240M 10
1
GND
GND
470
J6
2
nENABLE_RS0233
1A1
1A2
1A3
1A4
2
ENABLE_RS0232
2
4
6
8
1
U7
B
2Y1
2Y2
2Y3
2Y4
1
GND
74LV244
10
nHPI_CONTROL
TXD0
RXD0
JUMPER
JP6
JP7
1
GND
GND
GND
HPInWAITERR_SSCRD
HPID1_SSCTK
HPID3_SSCTF
1
3
5
7
9
2
4
6
8
10
HPID0_SSCTD
HPID2_SSCRK
HPID4_SSCRF
HEADER 5X2 MALE
GND
A
A
GND
SSC INTERFACE
HPI + SSC + UART0 (OMLY FOR CO2128)
Title
IIEVB-600
5
4
3
2
Size
B
Document Number
Date:
Monday, April 16, 2007
Rev
1.1
Sheet
1
4
of
9
5
4
3
5V
2
TIP
C51
100NF
U8
C54
1NF/3KV
GND
GND
-RESET
GND
GND
24
-RESET
26
27
28
29
30
31
32
DGND
-RDL
-PULSE
DCDLED
RXLED
DTRLED
TXLED
SMB8
SMB7
SMB6
SMB5
SMB4
SMB3
SMB2
SMB1
52
51
50
49
48
47
46
45
DGND
-DTR
-DCD
-CTS
-DSR
-RI
TXD
RXD
-RTS
41
40
39
38
37
36
35
34
33
SPKR
GND
GND
100NF
C52
VDD
SPI1CS_I2CTWCK
SPI1CLK_I2CTWD
SPI1MOSI_SCINTB
SPI1MISO_SCIO
SPI0CS_SCRST
SPI0CLK_SCC4
SPI0MOSI_SCC8
SPI0MISO_SCCLK
G1
G2 U9
LM386
5
GND
3
D
+
+
BP
C57
100NF
C56
10UF/16V
LS1
GND
R70
10
+
GND
-DTR
-DCD
-CTS
-DSR
-RI
TXD
RXD
-RTS
- V+
C58
10UF/16V
GND
GND
HPE1206
GND
MT34000SMI
C
C
VDD
VDD
C60
100NF
nEN_MODEM
100K
1
19
1OE
2OE
ERXCK_RXD1
ETX3_DCD1
ERX2_DSR1
ECRS_CTS1
TXD1
DTR1
ETXER_TXD1
ETX2_DTR1
ECOL_RTS1
RXD1
ERXCK_RXD1
ERX3_RI1
ETX3_DCD1
ERX2_DSR1
ECRS_CTS1
JP10
JUMPER
CD1
C65
100NF
2
VDD
EN_EXT_COM1
1
GND
JUMPER
GND
74LVX240M 10
2
C2-
14
13
12
TIN1
TIN2
TIN3
20
19
18
17
16
15
ROUT2B
ROUT1
ROUT2
ROUT3
ROUT4
ROUT5
23
FORCEON
22
FORCEOFF
V-
TOUT1
TOUT2
TOUT3
RIN1
RIN2
RIN3
RIN4
RIN5
2Y1
2Y2
2Y3
2Y4
9
7
5
3
SP3243ECA
INVALID
4
3
C61
470NF
GND
GND
C63
470NF
9
10
11
TXD1232
-DTR1232
-RTS1232
4
5
6
7
8
RXD1232
-RI1232
-CD1232
-DSR1232
-CTS1232
-CD1232
-DSR1232
RXD1232
-RTS1232
TXD1232
-CTS1232
-DTR1232
-RI1232
1
6
2
7
3
8
4
9
5
J8
B
GND
21
GND
GND
nEN_COM1_LED
EN_MODEM
R73
GND
R74
100K
R75
470
GND
D3
G.LED
R76
470
D4
G.LED
R77
470
470
D5
G.LED
A
GND
GND
GND
GND
D6
G.LED
MODEM + UART1
Title
IIEVB-600
GND
5
GND
27
2
1G
2G
C2+
R72
100K
1
1
19
18
16
14
12
2
2A1
2A2
2A3
2A4
1Y1
1Y2
1Y3
1Y4
1
11
13
15
17
VCC
2
nEN_COM1_LED
EN_EXT_COM1
A
1A1
1A2
1A3
1A4
1
EN_MODEM
nEN_MODEM
2
4
6
8
2
TXD1
RXD1
CD1
DTR1
20
1
U12
1
V+
JP11
VDD
GND
GND
C1-
VCC
9
7
5
3
2Y1
2Y2
2Y3
2Y4
24
C64
470NF
GND
74LV244
10
1
2
2A1
2A2
2A3
2A4
C1+
DB9 MALE
R71
11
13
15
17
ERX3_RI1
28
11
RXD
-DCD
-DSR
-CTS
C62
470NF
TXD
-DTR
-RTS
10
VDD
-RI
U11
18
16
14
12
2
4
6
8
GND
ETXER_TXD1
ETX2_DTR1
ECOL_RTS1
GND
20
VCC
1A1
1Y1
1A2
1Y2
1A3
1Y3
1A4
1Y4
25
U10
26
100NF
FOR COM1
C59
B
2
C55
100NF
8
C53
1NF/3KV
64
63
62
61
1
2961666681
SPKR
AGND
MICV
VCC
7
TIP
RING
6
1
2
RING
4
1
3
RJ11
R69
2/2010
1
PHONE
1
RV1
DSS-301L
L1
4
3
2
1
3
D
4
J7
2
4
R68
2/2010
2
3
2
Size
B
Document Number
Date:
Tuesday, January 30, 2007
Rev
1.1
Sheet
1
5
of
9
5
4
3
2
1
VDD
VDD
C66
R78
10K
GND
VDD
1
E/D
2
GND
D
100NF
4
U13
D
3
OUT
U14
F4100-50MHZ
EREFCK
GND
VDD
ETX1
ETX0
ETXEN
VDD
R117
ERX1
ERX0
3K
GND
R79
10K
CRSDV
R80
10K
R135
C
3K
ERXER
GND
EMDC
EMDIO
VDD
IRQ1
NC
REF_CLK/XT2
17
18
19
20
21
22
TX3
TX2
TX1
TX0
TX_EN
TX_CLK/ISOLATE
26
27
28
29
RXD3/PHYAD3
RXD2/PHYAD2
RXD1/PHYAD1
RXD0/PHYAD0
34
37
RX_CLK/10BTSER
RX_DV/TESTMODE
R85
0
16
38
TX_ER/TXD4
RX_ER/RXD4/RPTR
36
35
COL/RMII
CRS/PHYAD4
24
25
32
MDC
MDIO
MDINTR
39
DISMDIX
100NF
C75
41
VDD
100NF
C76
30
VDD
100NF
C77
23
VDD
GND
R87
0
-RESET
43
TX+
7
TX-
8
RX+
3
RX-
4
VDD
AVDD1
GND
GND
GND
10
PWRDWN
40
RESET
1
2
3
4
5
6
7
8
AVDD1
C67
BK2125HM601
100NF
L2
AVDDR
1
AVDDR
2
100NF
AVDDT
9
AVDD1
100NF
AGND
AGND
AGND
5
6
46
BGRESG
47
AGND1
BGRES
LEDMODE
LED0/OP0
LED1/OP1
LED2/OP2
CABLESTS/LINKSTS
48
31
11
12
13
14
NC
45
C68
+
C71
+
100UF/16V
C69
100UF/16V
R81
R82
49.9 1% 49.9 1%
C70
100NF
R83
R84
49.9 1% 49.9 1%
TDP
TDN
RDP
TCT
RCT
RDN
NC
GND
9
10
SHILD
SHILD
11
12
D1
D2
13
14
D3
D4
C
C72
ERNI
AGND1
0
R149
C73
C74
100NF
100NF
AGND1
R86
6.8K1%
15
33
44
B
XT1
J9
VDD
R148
AutoMDIX
unable
42
VDD
AGND1
GND
AGND1
AGND1
B
GND
DM9161A
SPEED
ACT_LNK
470
470
R88
R89
J19
J20
IRQ0
CRSDV
ECOL_RTS1
EMDIO
1
3
5
7
9
2
4
6
8
10
HEADER 5X2 MALE
IRQ1
ERXER
ECRS_CTS1
EMDC
ERX2_DSR1
ERX0
ETXER_TXD1
EREFCK
ETX2_DTR1
ETX0
15
13
11
9
7
5
3
1
16
14
12
10
8
6
4
2
ERX3_RI1
ERX1
ERXCK_RXD1
ETXEN
ETX3_DCD1
ETX1
HEADER 8X2
VDD
A
A
GND
RMII INTERFACE
+ C109
1UF/16V
Title
IIEVB-600
Size
B
Document Number
Date:
Sunday, April 01, 2007
Rev
1.1
GND
5
4
3
2
Sheet
1
6
of
9
2
1
VDD
C106
100NF
100NF
D
JP16
GND
2
GND
2
JUMPER
1
2
JP17
R95
R96
R97
NC
NC
NC
PWR
CS
NC/NO
5V/3V
READY
ALARM
CARD
15
17
16
13
14
DATA
AUX1IN
AUX2IN
CIN
RIN
8
SDA
SCL
1
2
4
JP13
7
PRES
1
I/O
AUX1
AUX2
CLK
RST
18
19
JP14
JUMPER
+
VIN
VCC
GND
10UF/16V
J10
GND
1
2
3
4
5
6
7
8
C80
1UF/16V
SIM_IO
SIM_C4
SIM_C8
SIM_CLK
SIM_RST
10
8
9
12
11
1
2
3
4
SPI1CLK_I2CTWD
SPI1CS_I2CTWCK
J11
R94
D
JP12
JUMPER
GND
SIMVDD
0
1
6
A0
A1
A2
R91
10K
10K
CON4
GND
TWI INTERFACE
SIM CARD
GND
VDD
LTC1755
C
2
C
OS
7
6
5
JUMPER
C79
C+
C-
5
SPI1MISO_SCIO
SPI0CLK_SCC4
SPI0MOSI_SCC8
SPI0MISO_SCCLK
SPI0CS_SCRST
2
3
4
24
21
22
23
GND
+
SPI1MOSI_SCINTB
VDD
JUMPER
1
GND
GND
JUMPER
1
R93
10K
U15
R92
10K
JP15
20
VDD
3
VDD
2
C78
R90
2
C110
U27
LM75A
VDD
VDD
VDD
100NF
GND
GND
VDD
VDD
1
3
2
4
1
5
JP18
JUMPER
1
GND
J12
SPI1MISO_SCIO
SPI0CLK_SCC4
SPI0MOSI_SCC8
SPI0MISO_SCCLK
SPI0CS_SCRST
VDD
R138
R139
R140
R141
R142
R144
1
2
3
4
5
6
SPI1MISO_SCIO
SPI1MOSI_SCINTB
SPI1CLK_I2CTWD
SPI1CS_I2CTWCK
NC SIM_IO
NC SIM_C4
NC SIM_C8
NC SIM_CLK
NC SIM_RST
NCSIMVDD
CON6
GND
SPI1
B
INTERFACE
B
VDD
VDD
VDD
2
C81
GND
JP19
JUMPER
2
JUMPER
R98
100K
1
J13
VDD
CLK_IN
SO
SI
CS
GND
SPI0CS_SCRST
JP20
1
6
2
5
1
SPI0CLK_SCC4
SPI0MISO_SCCLK
SPI0MOSI_SCC8
M25P40-A
HOLD
WP
1
2
3
4
5
6
SPI0MISO_SCCLK
SPI0MOSI_SCC8
SPI0CLK_SCC4
SPI0CS_SCRST
7
3
CON6
4
100NF
8
U16
GND
GND
A
SPI0
VDD
A
INTERFACE
SPI0 FLASH + SPI1 + TWI + SIM INTERFACE
Title
IIEVB-600
5
4
3
2
Size
B
Document Number
Date:
Wednesday, January 31, 2007
Rev
1.1
Sheet
1
7
of
9
4
VDD
NC
2
SPI0MISO_SCCLK
2
SPI0CS_SCRST
JMP3
1
1
JMP3
JP25
NC
JP26
2
EMDIO
JMP3
JP27
2
EMDC
JMP3
R106
R107
R108
R109
R110
R111
R112
3K
3K
3K
3K
3K
3K
3K
GND
GND
GND
GND
GND
D
ICHIP_ERR
JMP3
1
2
ETXER_TXD1
JMP3
JP24
R105
1
2
HPIIBF_DTR0
JP23
3
R104
NC
3
R103
NC
3
R102
NC
JP22
1
VDD
R101
JMP3
1
VDD
1
2
VDD
NC
3
3
D
2
R100
NC
JP21
VDD
1
R99
VDD
3
VDD
3
3
5
GND
GND
C
C
VDD
C82
100NF
TIN1
TIN2
TIN3
RXD2
20
19
18
17
16
15
ROUT2B
ROUT1
ROUT2
ROUT3
ROUT4
ROUT5
EN_COM2
23
FORCEON
22
FORCEOFF
GND
B
2A1
2A2
2A3
2A4
1
19
1G
2G
1Y1
1Y2
1Y3
1Y4
18
16
14
12
2Y1
2Y2
2Y3
2Y4
9
7
5
3
VDD
1
R127
R129
NC
R130
470
GND
R133
R128 NC
470
NC
R114
470
470
D7
G.LED
2
74LVX240M 10
A
2
1
2
GND
D17
G.LED
D13
R.LED
2
D14
G.LED
R113
R134
470 GND
TXD2232
TXD2232
RXD2232
RIN1
RIN2
RIN3
RIN4
RIN5
4
5
6
7
8
R115
100K
SP3243ECA
INVALID
J14
1
6
2
7
3
8
4
9
5
RXD2232
GND
1
JUMPER
1
nEN_COM2
9
10
11
JP28
2
nEN_COM2
GND
TOUT1
TOUT2
TOUT3
21
GND
11
13
15
17
VCC
1
1A1
1A2
1A3
1A4
470NF
B
GND
25
EN_COM2
DATA_READY_FIQ
ICHIP_ERR
FW_RDY
2
4
6
8
2
TXD2
RXD2
RXD2
20
GND
C85
GND
D8
G.LED
GND
1
U18
C83
DB9 FEM
14
13
12
V-
3
RS232 TO COM0
C2-
27
11
C2+
2
V+
10
1
TXD2
470NF
26
C1-
VDD
C86
100NF
C1+
24
C87
470NF
TXD2
28
VCC
U17
C84
470NF
GND
GND
A
GND
GND
VDD
GND
VDD
UART2 + CONFIGURATION PINS
VDD
Title
IIEVB-600
5
4
3
2
Size
B
Document Number
Date:
Tuesday, January 30, 2007
Rev
1.1
Sheet
1
8
of
9
5
4
3
2
VIN
1
10K R146
5V
LT1086CM
10UF/16V
C91
100NF
C88
VOUT
CASE
1
ADJ
VIN
VDD
3
C111
1.2V
GND
U19
GND
R118
300
R119
HDM
J15
R147
470
6
10UF/16V
VIN
1
EN
3
D
C93
470NF
TPS76912
GND
GND
GND
HDP
GND
HDP
3.3V
27
C95
47PF
15K
C92
R145
10K
R121
GND
R122
VOUT
1
GND
GND
5
+
D20
R.LED
GND
USB-A
-
U20
2
C94
47PF
15K
AD8030
5
HDM
27
R120
1
2
3
4
+
7
4
D
VDD
EXT_VDDCORE
TP
U26B
100NF
GND
C90
100NF
R116
100
+
2
RXE020
TP
2
4
1
F1
1
8
5V
VDD
TP
VIN
1
GND
FEEDBACK
SW3
D10
U21
4
1
VIN
1
J16
2
3
1
2
GND
C
SWITCH
DC-JACK
C
C99
100NF
D11
MUR115
ON/OFF
1000UF/25V
+
C96
C98
100NF
5
PGND
C97
SGND
1
2
LM2591HVS-3.3
GND
2
USB-B
1
R125
NC
GND
GND
D19
R.LED
OTPUT
6
27
C101
15PF
15PF
VDD
2
L4
68UH/1A
+
1
DDP
C100
1000UF/25V
1
2
3
4
3
J17
DDM
R124
DDP
R143
470
1
DDM
27
2
1N4001
R123
GND
TP
GND
MSEL
AVDD
AVDD
C102
AVDD
100NF AGND
AGND 100NF
AD8030
TS5A3159
4
nHPI_CONTROL
6
1
NC
3
+
-
2
1
2
LL4148
D15
8
AVDD
RESET
-RESET
2
R132
U23B
GND
ADVREF
+
AD8030
5
-
6
P1
NC R136
POT
2
A
7
SP708RCN
GND
+
10UF/16V
C108
0
D18
R137
NC
1.2V
OPTIONAL
Title
USB+POWER+RESET + ANALOG INPUT
2
GND
GND
3
-
8
6
8
7
5
4
NC
RESET
RESET
PFO
AVDD
AGND
1
AD8030
3
2
+
1
1
GND
AVDD
4
1UF/16V
3
TACK_SW
C107GND
MR
PFI
VCC
U24
1
4
+
CON2
AGND
U26A
GND
SW2
15K
GND
4
HPID5
C104
47PF
AGND
LL4148
A
J18
1
100NF
D16
B
R126
3
2
IN
VDD
C105
NO
COM
GND
VDD
VDD
R131
4.7K
HPID5_ADC
LL4148
D12
U23A
8
U22
SW1
VDD
B
5
TACK_SW
C103
GND
Size
B
Document Number
Date:
Tuesday, January 30, 2007
Rev
1.1
AGND
5
4
3
2
Sheet
1
9
of
9
II-EVB-600 User Manual
2.9
Getting Started
Running the iChipConfig Utility for the First Time
This section describes how to start running the iChipConfig Utility.
To start the iChipConfig Utility:
1. Select Programs > ConnectOne > iChipConfig from Windows Start menu. The iChip
Configuration Tools window is displayed:
2. Select the desired operation by clicking the appropriate icon.
When an icon is selected (except Exit), the iChipConfig utility attempts to locate the
II-EVB-600 on one of the PC’s COM ports at the default baud rate of 38400.
If the II-EVB-600 is not located, the Serial Settings dialog box is displayed:
Getting Started
24
II-EVB-600 User Manual
Getting Started
This dialog box is also displayed if you select Serial Ports from the menu bar.
3. From the Serial Port drop-down list, select the port to which the II-EVB-600 is attached.
4. In the Baud Rate area:

Select the exact Baud Rate used by the II-EVB-600.
-or-

Select Scan if you don’t know the baud rate.
If Scan is selected, iChipConfig Utility runs through the different baud rates until the correct
baud rate to be used is found. The following message is displayed:
Note: If iChipConfig Utility still fails to find the II-EVB-600, make sure that there are no
applications open, such as Palm HotSync, occupying the port; switch to a different COM port and
try Scan again. After iChipConfig has found the baud rate, you can easily change it by opening
the Serial Settings dialog box and selecting the desired baud rate.
2.10
Configuring for Connection
To be part of the LAN, the II-EVB-600 needs basic LAN settings, such as IP Address, Subnet and
Gateway IP address. There are two ways to configure this set of parameters for II-EVB-600:

Dynamic IP Allocation (Via DHCP)

Fixed IP Configuration (Via User Assignment)
Getting Started
25
II-EVB-600 User Manual
2.10.1
Getting Started
Dynamic IP Allocation
By default, the II-EVB-600 is configured to gain LAN access via DHCP. Therefore, if a DHCP
server is present, there is no need for additional configuration.
Specific configuration for acquiring LAN settings via DHCP can be carried out from the Quick
Configuration window in the figure below:
1. Select the Use DHCP check box and click Save.
2. To activate these settings, recycle power to the II-EVB-600.
Note: II-EVB-600 supports DHCP Server extensions. This means that if your server’s assignees’
have additional LAN settings, such as SMTP server, the II-EVB-600 automatically configures and
uses these settings.
2.10.2
Fixed IP Configuration
To configure the II-EVB-600 to work with a fixed IP address, the following parameters should be
configured:
1. Use the Quick Configuration screen to set the following parameters:
Getting Started
26
II-EVB-600 User Manual
Getting Started

IP Address (DIP): Set it to the IP address you want the II-EVB-600 to have.

Subnet (SNET)

IP Gateway (IPG)
2. Click Save and recycle power to the II-EVB-600.
These settings can also be configured using the following AT+i commands:

AT+iDIP

AT+iSNET

AT+iIPG
A detailed description of these commands can be found in the AT+i Programmer's Manual.
Getting Started
27
II-EVB-600 User Manual
3
Firmware and Parameters Update
Firmware and Parameters Update
This section describes the II-EVB-600 local firmware and parameters update capabilities using
the iChipConfig utility.
It also describes how to create and use parameter files (*.RPF).
3.1
Local Firmware Update
The II-EVB-600 can be updated locally in one of two ways. You can upload the firmware directly
from the host (PC, in our case) via the RS232 interface, or from the external flash memory
provided on the II-EVB-600 via the SPI interface.
3.1.1
Loading the Firmware from Host
To load the iChip firmware from host memory via the RS232 serial interface, you need to obtain
the RAM version of the firmware flavor you wish to install from Connect One. The RAM version is
provided as two separate files: a version.hdr file and a version.dat file. The following procedure
assumes that you have a host application running on your PC, in which you insert appropriate
lines of code, as detailed below.
1. Power up the II-EVB-600 and assert the MSEL pin for at least 5 seconds.
2. Use the connected UART at a baud rate between 9600 and 115200 to send a capital U
character to the iChip. Wait for a > prompt.
3. Send a capital L and wait for a > prompt.
4. Send the version.hdr file and wait for a > prompt.
5. Send the version.dat file.
6. The firmware is now loaded into iChip’s RAM and ready for use.
3.1.2
Loading the Firmware from SPI Flash Memory
1. Invoke the iChipConfig utility.
Miscellaneous Operational Features
28
II-EVB-600 User Manual
Firmware and Parameters Update
2. Click Tools > CO2128/2064 Monitor Mode.
3. In the dialog box displayed, select the SPI Flash 4 Mbit check box and click OK.
4. Wait for the utility to finish loading FPRO into iChip’s RAM.
5. Power up the II-EVB-600 while holding down the MSEL switch for at least 5 seconds and OK
the dialog box.
Miscellaneous Operational Features
29
II-EVB-600 User Manual
Firmware and Parameters Update
6. In the dialog box displayed, click the FW Update button.
7. In the dialog box that appears, select the .imf image file of the firmware you wish to upload
and click Open.
Miscellaneous Operational Features
30
II-EVB-600 User Manual
Firmware and Parameters Update
8. Click Yes when prompted.
9. The following screen appears:
10. Click OK on the Image file loaded successfully dialog box.
The firmware is loaded into the SPI flash memory. When you reset the iChip, it automatically
loads the firmware from flash memory into its internal RAM.
3.2
Managing Parameter Files
Parameters for the II-EVB-600 are stored in *.RPF files. Parameter files can be used to save
current configurations to be loaded for later use or to automate product distribution.
Miscellaneous Operational Features
31
II-EVB-600 User Manual
3.2.1
Firmware and Parameters Update
Saving the II-EVB-600 Configuration to an RPF File
The parameters stored in the II-EVB-600 can be saved to a Remote Parameter File (RPF) or
loaded from an RPF file onto the II-EVB-600.
To save the current configuration to an RPF file:
1. Click the Full Configuration icon. The II-EVB-600 Full Configuration window is
displayed.
2. Click File > Save as RPF File in the Full Configuration window. The RPF Parameters
dialog box is displayed:
3. Configure the following parameters and click OK:

Select the Start from factory defaults check box if you want to save the factory
default settings as your new parameters.

Do not select the Start from factory defaults check box if you want to save your
current configuration (except for parameters) in the RPF file.

Group - Not relevant

Destination Chip Serial Number - Not relevant
3.2.2
Loading an RPF File
To load an RPF file onto the iChip:
1. Select File > Load RPF file from the iChipConfig menu. The Open dialog box is
displayed:
Miscellaneous Operational Features
32
II-EVB-600 User Manual
Firmware and Parameters Update
2. Browse to the appropriate RPF file and click Open. All the parameters from the RPF file
are loaded onto the II-EVB-600.
3.
If an illegal parameter value has been assigned, iChipConfig Utility displays the illegal
parameter and offers to save it to a log file. Enter a new valid parameter value and
Load/Save the RPF file again.
Miscellaneous Operational Features
33