Download Operating Instructions

Dear Customer,
Thank you for choosing this quality product from ASKO.
We hope it will meet your expectations and fulfil your needs for many years
to come. Scandinavian design combines clean lines, everyday functionality
and high quality. These are key characteristics of all our products and the
reason they are greatly appreciated throughout the world.
To get the most out of your new machine, we recommend that you read the
operating instructions before using the machine. The operating instructions
also include information on how you can help protect the environment.
Operating Instructions
Washing Machine
W8844 XL ECO
CONTENTS
SAFETY INSTRUCTIONS
Child safety
3
3
TROUBLESHOOTING14
The washer door will not open
14
Installation4
Opening the door in an emergency
14
Overflow guard function
4
The machine will not start
14
Transport/winter storage
4
After power failure
14
Packing material
4
Wet washing still in the machine
14
Error messages
15
Recycling4
ADVICE AND TIPS BEFORE WASHING
5
TECHNICAL INFORMATION
Laundry label symbols
5
Information for test institute
16
Sorting your laundry
5
Technical data
18
Clothing5
Coloured cotton
5
Unbleached linen
5
Wool5
Save time and energy
6
High water level
6
Economy and efficiency
6
Detergents6
Dyeing fabrics
USING YOUR WASHING MACHINE
6
7
Add detergent and fabric softener
7
Program selection
8
Selecting options
9
During the programme
INSTALLATION19
Positioning the washing machine
19
Adjusting the feet
19
Connection to water supply
19
Drainage connection
19
Electrical installation
20
BEFORE CONTACTING THE SERVICE
DIVISION21
Before contacting the service division
22
QUICK GUIDE
24
10
Cleaning the trap and the drainage pump
12
Cleaning the detergent compartment
12
Cleaning the outside of the machine
12
Cleaning the inside of the machine to avoid
unpleasant smells
12
Rinse holes under the agitator
12
If you have hard water
13
21
PROGRAMME CHART
SETTINGS11
Original instruction
WARNING: Read the instructions before using the machine.
2
16
SAFETY INSTRUCTIONS
GENERAL
CHILD SAFETY
• Installation should be carried out by qualified ASKO
technicians.
• The appliance is not intended for use by young
children or infirm persons without supervision.
• Read the operating instructions and keep them in a
safe place.
• The machine should only be used for washing items
as described in these instructions. It is not intended
for dry cleaning.
• Use only detergent intended for machine washing!
• Use only detergents and softeners for machine wash.
Manufacturer may not assume responsibility for any
damage and eventual discolouring of gaskets and
plastic components as a consequence of incorrect
use of bleach and/or colouring agents.
• Never use detergents containing solvents, since
there is a danger of creating toxic gasses which
may damage the machine and result in ignition or
explosion.
• Repairs and maintenance must be carried out by a
qualified professional.
• Damaged mains cables must only be replaced by a
qualified electrician.
• The machine is not designed to be used by persons
(even children) that are physically or mentally
handicapped or lack experience and knowledge.
Such persons must receive instruction in how to
use the machine or be supervised by a person
responsible for their safety.
• Always close the door and start the programme
immediately once you have added detergent.
• Young children should be supervised to ensure that
they do not play with the appliance.
• Store detergent and fabric softener out of the reach of
children!
CAUTION!
If this appliance is supplied from a cord extensions
set or electrical portable outlet device, the cord
extension ser or electrical portable outlet device must
be positioned so that it is not subject to splashing or
ingress of moisture.
Activate Child-safe start (button lock)
You can activate the Child-safe start option (button lock)
to prevent children from starting the washing machine
(see the Settings section).
Activate child safety catch (for detergent
compartment)
On the inside of the detergent compartment is a child
safety catch.
• Children must be watched to ensure they do not play
with the machine.
• In the enclosed plastic bag you will find a tool for
opening the washer door in emergencies.
Activated child
safety catch
Inactivated child safety
catch
When the child safety catch is activated you must
press the release button to pull out the detergent
compartment.
3
SAFETY INSTRUCTIONS
INSTALLATION
• Carry out the installation and connections in
accordance with the separate installation instructions.
• Installation of water and electricity, if required, must
be carried out by a qualified tradesperson.
• Remove any transport protection devices before
using the machine. See the separate installation
instructions.
OVERFLOW GUARD FUNCTION
If the water level in the machine rises above normal,
the overflow guard function begins to pump water out
and shuts off the water intake. If the water level has
not dropped within 60 seconds, the programme is
terminated.
TRANSPORT/WINTER STORAGE
If the machine is to be transported or stored in unheated
premises where the temperature can fall below freezing,
do as follows:
• Empty the filter and the drainage pump. See the “Care
and cleaning” chapter.
• Shut off the water to the washing machine, loosen the
supply hose to the intake valve and let the water run
out from the valve and hose.
• After emptying the pump, a small amount of water
may remain in the machine. This does not affect
quality or damage the machine.
PACKING MATERIAL
Sort waste materials in accordance with local guidelines.
RECYCLING
• This dishwasher is manufactured and labelled for
recycling. In order to prevent injuries, the machine
must be rendered unusable once the decision
has been made to dispose of it. Contact your local
authority for information about where and how your
machine can be correctly recycled.
4
ADVICE AND TIPS BEFORE WASHING
LAUNDRY LABEL SYMBOLS
Examples of washing instructions and recommended programmes. Always follow the washing instructions for each
garment.
Laundry labels
Material
Cotton, linen, white and light-coloured items.
Program
Everyday wash 60 °C to 95 °C
Cotton, linen, cotton/polyester. Light and dark-coloured
garments.
Acrylic, viscose, modal, acetate, polyester, polyamide
and elastane. Light and dark-coloured garments.
Quick 60 °C
Wool, silk and other very delicate garments
Wool/hand wash 30 °C to 40 °C
Easy Care 40 °C
or
Here are some tips that may help you before washing.
SORTING YOUR LAUNDRY
Sort items according to:
• how soiled they are
• colour
• material
CLOTHING
1 Do up zips and close Velcro straps so that they don’t
harm fabrics.
2 New coloured items may contain excess dye and
should therefore be washed separately the first few
times.
3 Turn delicate items inside out. This reduces the risk
of burling and fading.
4 Empty pockets and wash them inside out if possible.
COLOURED COTTON
Coloured cotton garments labelled with washing
instruction 60 °C must be washed at 60 °C initially to
remove any excess dye. Failure to observe this advice
could lead to the colour running.
Use detergent without bleach to preserve the colour of
the fabric.
UNBLEACHED LINEN
Unbleached linen fabrics should be washed at 60 °C,
using detergent without bleach or optical brighteners.
Heavily soiled linen can be washed at higher
temperatures, but not too often as the heat may destroy
the sheen and strength of the linen.
WOOL
These fabrics are labelled for either machine wash or for
hand wash. The machine’s Wool/hand wash programme
is at least as gentle as washing by hand.
Wool is especially sensitive to processes such as
washing. If you do not wish to spin dry, you can squeeze
out the water using terry towels. In this case select No
spin. However, most garments can withstand a short spin.
Choose a short spin by selecting a spin speed of 800 rpm
or less.
LAUNDRY LABELS
Look at the item’s laundry label. The table below shows
suitable wash programmes for different materials and
wash loads. Using modern washing machines and
detergents, for example compact detergents, you can
usually wash at lower temperatures. It is a good idea
to use trial and error to find out what produces the best
results.
RAYON FIBRES AND SYNTHETIC
FIBRES
Materials made of rayon fibres, such as viscose, and
some synthetic fibres are very delicate and require much
space so as not to crease. Only half fill the drum when
washing and choose a spin speed of 800 rpm or lower.
NOTE!
Viscose and acetates are fragile when wet.
5
ADVICE AND TIPS BEFORE WASHING
SAVE TIME AND ENERGY
Use the Everyday wash program to save time and energy.
This program has a shorter main wash than Standard
cotton, but is often sufficient for lightly soiled washing.
HIGH WATER LEVEL
If you want more water for the main wash and rinses, you
can use the High water level option. High water level is
used automatically in the Wool/hand wash programme.
ECONOMY AND EFFICIENCY
You can save a lot of energy by not using higher
temperature programs than necessary.
• Select Quick if you just need to freshen up shirts or
exercise clothes, for example. This will save both water
and energy.
• If you select a fast spin speed, this reduces energy
consumption when drying in a tumble dryer or drying
cabinet.
• Always wash with a full load when using the Heavy,
Everyday wash and Normal programs.
• Avoid pre-washing. Modern machines and detergents
clean effectively without pre-washing. Pre-washing is
only necessary for heavily soiled washing.
DETERGENTS
Eco-labelled detergents are less harmful to the
environment. Detergent overdosing does not give better
washing results; it merely causes a greater impact on the
environment. Try to use less detergent, and increase only
if you are not satisfied with the results.
DYEING FABRICS
If you want to dye fabrics in the machine, select the
Everyday wash programme with the Super rinse option.
Select temperature according to the dye manufacturer’s
recommendations. Choose a low spin speed if the fabric
to be dyed is a blended material such as polyester/cotton.
NOTE!
Add the dye directly to the washing drum – not to the
detergent compartment. After dyeing, you should run
the machine empty using the same program. Use the
normal amount of detergent.
NOTE!
Due to environmental concerns, we discourage the use
of strong chemicals.
When using agents for bleaching or stain removal,
there is a risk of rust (corrosion) and discolouration of
the machine.
6
USING YOUR WASHING MACHINE
ADD DETERGENT AND FABRIC
SOFTENER
Powder detergent
Pour the powder into the compartment for the main
wash, and pre-wash as well if desired. Do not use the
separator in the main detergent compartment.
5
1
2
3
Liquid detergent
4
When using a liquid detergent, observe the detergent
manufacturer’s recommendations. We recommend
using a laundry ball with thick detergents. In the main
detergent compartment, use the section wall (A). Add
the detergent into the front compartment of the detergent
dispenser.
6
Wash ball or net
If you use a wash ball or net, place it directly in the drum
and select a programme without pre-wash.
NOTE!
Detergent overdosing does not give better washing
results; it merely causes a greater impact on the
environment; can also hinder the wash performance.
1.Pre-wash
2. Main wash with liquid detergent.
Use the separator (A).
3. Main wash with powder detergent.
Do not use the separator.
Try using less detergent, and increase only if you are
not satisfied with the results.
Fabric softener
Pour the fabric softener into the compartment with the
symbol . Follow the recommendations on the fabric
softener packaging.
4. Fabric softener
5. Release button
6. Child safety catch
NOTE!
Do not fill above the compartment’s maximum fill level.
Otherwise fabric softener will run in too early, and will
impair washing results.
A
B
C
The quantity of detergent needed depends, amongst
other things, on how hard the water is. See the detergent
pack for details. Phone your local water company to
check the water hardness in your area.
The detergent packaging will have recommendations
for how much detergent you should use. The machine
holds 10 kg of washing. If you only have a small amount
of laundry in the machine, you can reduce the amount of
detergent used.
7
USING YOUR WASHING MACHINE
PROGRAM SELECTION
You select a programme by turning the programme
selector. The selected programme is shown in the
display. Now use the option buttons to select any
options. See chapter Selecting Options.
Garments worn next to the skin ought to be washed at
60 °C. Very lightly soiled laundry generally gets clean
already at 40 °C. The spin speed can be selected freely.
6. Quick
Fast program for laundry that just needs freshening up.
The program can be run at any temperature, so follow
the washing instructions for each garment. The lower
the selected temperature, the shorter the program time.
Garments worn next to the skin ought to be washed at
60 °C. The spin speed can be selected freely.
7. Easy Care
1.Auto
This program automatically adjusts the length of the
main wash and the number of rinses to the amount and
type of laundry loaded in the machine.
Programme for synthetic, mixed fibre and easy care
cotton. The programme has a High water level and
as such is also suitable for cushions, quilted jackets
and the like. Read the washing instructions carefully
and remember, for example, that fabric softener must
not be used with the membranes found in some outer
garments. A washing temperature up to 60 °C and a spin
speed up to 1200 rpm can be selected.
2.Time program
8. Synthetics
This program adjusts itself to the specified time frame
or finish time. When using this program, it is however
important to select a temperature and time suited to how
soiled the laundry is. The spin speed can be selected
freely.
Specify the desired programme time by pressing + or on the Time button. The symbol for the programme lights
beside the selected time. You can choose a programme
time between 30 minutes and 3 hours. If you choose
a 30-minute programme time the maximum wash
temperature will be 30 °C
3. Heavy
Programme for heavily soiled laundry, with dirt that
needs to be fully dissolved before the main wash. A
pre-wash is used to do this. The machine adapts the
programme time and water consumption to the load size.
4. Normal
Program for normal to heavily soiled laundry, whites and
colours. You can select the temperature freely, so follow
the washing instructions for each garment. 60 °C is a
good temperature for heavily soiled cotton garments,
as well as for garments worn next to the skin. Select 40
°C if the laundry is less soiled. The spin speed can be
selected freely. The machine adapts the program time
and water consumption to the load size.
5. Everyday wash
A standard programme for lightly to moderately soiled
laundry. The temperature can be selected freely, so
follow the washing instructions for each garment.
8
Programme for delicate garments made of synthetic
fibre, mixed fibre, rayon and easy care cotton. The
maximum temperature is 60 °C, but follow the washing
instructions for each garment. Many synthetics will
become clean at 40 °C. Garments worn next to the skin
ought to be washed at 60 °C. The maximum spin speed
is 600 rpm.
9. Wool/hand wash
A gentle laundry programme for wool, silk, and
garments that should be washed by hand. The highest
temperature is 30 °C. The programme has a short spin.
The maximum spin speed is 600 rpm.
10. Rinse
This program performs one cold rinse cycle + spin.
Suitable for laundry that just needs to be dampened and
for cleaning cloths and mops.
11. Spin
Used to just spin the wash.
12. Drain
Used when you only want to drain the water from the
machine.
USING YOUR WASHING MACHINE
SELECTING OPTIONS
You can select options to adjust the wash programme
to suit your own specific requirements. The available
options depend on the selected programme. If the option
is available for the selected programme, the symbol
lights up when you press the button.
The machine will remember the options you select for
each programme (applies to Super rinse, High water
level and Super wash). You can still change the selected
options the next time you select the same programme.
Temperature
• Select the temperature by pressing the -/+ buttons
until the desired temperature is displayed.
• You can select temperatures between cold (-) and 90
°C. By selecting cold, the wash temperature will be
the same as the temperature of the water entering the
machine. For Wool/hand wash it is not possible to select a temperature above 40 °C, when selecting Time
program, Synthetics and Easy Care the maximum
temperature is 60 °C.
Spin
• Select the spin speed by pressing the -/+ buttons until
the desired spin speed is displayed.
• You can select speeds between 400 and 1400 rpm,
(no spin) or No D(no drain). The maximum spin
speed varies according to the program selected. The
speed is shown in the display.
•
, means that the program does not include a spin
cycle and ends by draining.
• No D, No drain means that the program does not
include a spin cycle and ends with the water from the
final rinse still in the machine. The washing will remain
covered by the water from the final rinse, stopping it
from getting creased. If you have selected “No drain”,
once the program has ended you must select the Spin
or Drain program to drain the water from the machine
before you open the washer door.
Delayed start
When you select Delayed start the machine will start
1-24 hours after you press the Start button. This option
cannot be used with Time program.
• Select Delayed start by pressing the + button under
the time display. Delayed Start is shown for three
seconds.
• By pressing the -/+ buttons under the time display you
can delay the start in whole hours up to a maximum of
24 hours. The symbol for Delayed start lights beside
the number of hours.
• Press Start, and the machine counts down 1 hour at a
time and starts after the selected delay.
If you change your mind and want to cancel Delayed
start, you must press and hold the Stop button for three
seconds.
NOTE!
Remember to press the Start button to start the
program..
NOTE!
Make sure the detergent compartment is completely
dry before you add detergent, otherwise there is a risk
that the detergent will clump before the machine starts.
Super rinse
Use the Super rinse option if you want to increase the
number of rinses. The maximum number of rinses is
seven, and the number of rinses varies depending on the
selected programme. Recommended for persons with
extremely sensitive skin and/or in areas with very soft
water.
• Select Super rinse by pressing the button under the
symbol.
• The symbol above the button lights when this option
is activated.
9
USING YOUR WASHING MACHINE
High water level
Use High water level if a garment’s laundry label shows
this symbol. High water level means that additional water
is used during the main wash and rinse cycles.
• Select High water level by pressing the button under
the symbol.
• The symbol above the button lights when this option
is activated.
NOTE!
The machine takes in the additional water for the High
water level about 15 minutes after the main wash has
started.
Anti crease
Anti crease means that the drum will rotate for three
seconds per minute for two hours once the wash
programme has finished. This function prevents the
clothes from lying in the same position and getting
creased.
• Select Anti crease by pressing the button under the
symbol.
• The symbol above the button lights when this option
is activated.
Super wash
Super wash can be selected to better dissolve difficult
stains and heavy soiling on clothing. This options adds
a cold pre-wash and the the wash time in cold water is
extended by approximately six minutes. The main wash
time is also extended.
• Select Super wash by pressing the button under the
symbol.
• The symbol above the button lights when this option
is activated.
Pre-soak
If the washing is stained, such as with blood, we
recommend Pre-soak. The washing will soak in cold
water for two hours before the wash programme starts.
• Select Pre-soak by pressing the button under the
symbol.
• The symbol above the button lights when this option
is activated.
10
DURING THE PROGRAMME
Time remaining
The time remaining is shown in hours and minutes.
The time remaining is updated three times during the
programme. The first update takes place after about 15
minutes. Once a programme is selected, the estimated
programme time is displayed. This may differ depending
on the temperature of the water entering the machine
and the size of the load. If the programme time is longer
than the previous wash with the same programme, “0:01”
will be displayed until the programme finishes. This is
normal! The next time you use the programme under
similar conditions, the estimated programme time will be
more accurate.
Stopping or changing a program
You can stop a programme by pressing the Stop button
for three seconds. ”Stop” appears in the display. To
restart the machine, select a new programme, add any
extra detergent needed and press the Start button.
NOTE!
Do not open the detergent compartment while the
machine is running.
NOTE!
Upon completion of the washing cycle, close the water
faucet and unplug the mains cord.
SETTINGS
HOW TO CHOOSE THE SETTINGS
YOU CAN CHANGE THE FOLLOWING
SETTINGS
2 Press and hold the Stop button and then press the
main power switch. Then press the Stop button 5
times within 10 seconds.
Child-safe
1 Turn off the machine using the main power switch.
3 Select the setting you want to change by turning the
program selector.
4 Press the Stop once.
MAKING A SELECTION
You can activate the Child-safe start option to prevent
children from starting the machine. Select “Child-safe
On” or “Child-safe Off”.
Deactivate the Child-safe option temporarily for three
minutes by simultaneously pressing the buttons as
illustrated:
Turn the programme selector until the desired selection
is shown in the display
SAVING A SELECTION
1 Press Stop to save the selection and return to the
settings menu.
2 Press Start to go to the program menu.
Options:
Press Start to save the selection and return directly
to the programme menu, if you do not want to make
anymore settings.
Language
Choose from: US English, AU English, Svenska, Dansk,
Norsk, Suomi, Français, Deutsch, Italiano, Espanol,
Русский, Ned erlands, EU English.
Temperature
Choose between: °C and °F.
Extra rinses
Upon delivery, your washing machine is set to use three
rinses in the Standard cotton andEveryday wash.
Choose “Rinses On” for five rinses or “Rinses Off” for
three rinses.
11
CARE AND CLEANING
CLEANING THE TRAP AND THE
DRAINAGE PUMP
The washing machine has a trap where smaller objects
such as coins and hairpins can collect. To clean the trap
and the drainage pump, do as follows:
CLEANING THE DETERGENT
COMPARTMENT
Pull out the detergent compartment using the release
button.
1 Make sure the machine is empty of water and
switched off at the mains.
2 Open the door.
3 Unhook the drainage hose from the connector inside
the door and drain the water into a suitable container,
such as a shallow bowl.
Rinse the compartment and scrub it clean. The cover in
the fabric softener compartment can be removed.
NOTE!
Do not run the detergent compartment through a
dishwasher!
CLEANING THE OUTSIDE OF THE
MACHINE
4 Turn the cover anti-clockwise to open the pump.
Remove the cover.
Clean the outside of the machine and the program panel
with a mild cleaner. Do not use any solvents, as these
can damage the machine.
NOTE!
Do not hose down the machine with water!
5 Remove any items and so forth from the pump
housing and the cover. Also check that the pump
blades right at the back rotate.
CLEANING THE INSIDE OF THE
MACHINE TO AVOID UNPLEASANT
SMELLS
Run a programme at 90 °C or 95 °C (depending on the
model) with a small amount of detergent once a month
to avoid problems with odours. It is not necessary to put
any washing in the machine.
RINSE HOLES UNDER THE AGITATOR
6 Screw on the cover, replace the drainage hose on the
hatch pin and close the hatch.
12
If you suspect that objects such as nails or paper clips
may have fallen into the wash drum, you should check
the space under the agitator. Such objects can rust and
leave marks on clothing. Nails and other sharp objects
can cause holes in fabrics.
CARE AND CLEANING
Do as follows:
1 Insert a screwdriver or the like into the hole on the
agitator as illustrated and carefully pry to the left.
IF YOU HAVE HARD WATER
If you live in an area with hard water (high limescale
content), a greyish-white coating may form on the
washer drum. To remove this, empty a sachet of citric
acid, approx. 20 gram , into the washer drum and run
any 90 °C programme. Repeat if necessary.
2 Use your other hand to grasp the agitator and pull it
towards you.
3 Lift the agitator.
4 Remove any objects.
5 Place the agitator in the mounting hole with the
F-mark towards you. Ensure that all the agitator
fasteners are in their holes in the drum. Push it in
until it catches.
13
TROUBLESHOOTING
THE WASHER DOOR WILL NOT OPEN
• Check that the main power switch is on.
• Has the power supply been cut off? Check the house
fuses (circuit breakers).
OPENING THE DOOR IN AN
EMERGENCY
WARNING
The door may only be opened
manually if the electric power is
cut and the machine has been
drained of water.
1 Run the Drain program to empty the water from the
machine. If this does not work the machine must be
drained manually. See “Cleaning the trap and the
drainage pump” in the “Care and cleaning” chapter.
2 Ensure that the main power switch is turned off and
that the plug has been removed from the wall socket.
3 Take the emergency door opening key (C) (see
figure in the section Using your washing machine)
and insert it into the slot on the right-hand side of the
washing machine door latch. The key is attached on
the back wall of the detergent dispenser. Remove the
detergent dispenser from the washing machine and
take the door opening key.
4 Push the tool downwards to open the washing
machine door.
After use, store the emergency door opening key (C) in
the dedicated compartment (B) (see image in the section
Using your washing machine).
14
THE MACHINE WILL NOT START
• Is the washing machine door properly closed? Push it
firmly. Then press the Start button.
• Is there power? Check the fuses and residual current
devices (circuit breakers) in the building.
• Check that you have not selected Delayed start. To
cancel
Delayed start, press the Stop button for three seconds.
AFTER POWER FAILURE
Press the main power switch to resume the current
program.
WET WASHING STILL IN THE MACHINE
A small load can occasionally cause an imbalance
Unbalance (see “Unbalance”). Rearrange the load and
start the spin programme, or load more washing and
restart the washing programme.
TROUBLESHOOTING
ERROR MESSAGES
If an error occurs during the program a message is shown
on the display. To exit the message after taking measures,
turn the machine off and then back on.
The error messages that may be shown in the display are:
Close the Door
Close the washer door and press Start to start the
programme.
Over flow fault
1 Shut off the water tap.
2 See “Drainage error”.
Water outlet fault
Check:
• that no objects are stuck in the drainage hose outlet.
• that the drainage pump is not blocked by foreign
objects. Clean the pump. See the “Care and cleaning”
chapter.
• that there are no kinks in the drainage hose.
After the above, run Drain to empty the machine. If this
does not resolve the problem, call the service division.
Water inlet fault
Check:
• that the tap on the water pipe is open.
• that the filter in the machine’s water intake is not
blocked.
Action:
1 Shut off the water tap and unscrew the hose.
2 Clean the filter in the inlet valve on the machine.
3 Screw the hose back on and turn on the tap.
4 Run the program again to check if the fault is fixed.
5 If this does not resolve the problem, call the service
division.
Wash motor fault
Call the service division!
Unbalance
The machine stops the spin cycle if there is too much
imbalance. The washing machine restarts the spin cycle
and hopefully the washing is better distributed in the
drum. This procedure can be repeated up to 10 times.
If the machine still fails to find a good balance, the
programme jumps to the next step. The error message
requires no action.
15
TECHNICAL INFORMATION
INFORMATION FOR TEST INSTITUTE
Energy labelling
Australian standard:
AS/NZS 2040.1:2005
Washing program:
Normal, 40 °C, 10 kg cotton
Connection:
Cold water 20 °C
Test method for noise measurement: IEC-60704-2-4
Power requirement when machine turned off
< 0,3 W
Power requirement for Delayed Start
< 6,0 W
Power requirement when program finished
< 3,0 W
Detergent, PBIS and Anti-Sudsing Agent (20ml) must be added via the detergent compartment.
16
TECHNICAL INFORMATION
Loading procedure for standard test:
When loading the machine for testing according to AS/NZS 2040:2005 it shall be loaded according to the table below.
Garments are placed on top of each other in layers and the soil swatches should be placed inside the wash drum in the
direction shown in the table, seen from above.
Top
Swatches
Swatch placement
38. Pillow case
1
Right
39. Bath towel
37. Pillow case
36. Sheet
35. Undershorts
1
1
1
Left
Front
Left
34. T-shirt
1
Rear
32. Tablecloth
1
Right
30. Shirt
1
Front
28. T- Shirt
1
Front
33. Bath towel
31. Bath towel
29. Undershorts
27. Undershorts
26. Pillow case
25. Sheet
24. Wash cloths
1
1
1
1
Center
Front
Left
1
Right
21. T-shirt
1
Rear
20. Undershorts
19. Undershorts
18. Tablecloth
17. T-shirt
16. Shirt
15. Bath towel
14. Handkerchiefs
1
1
1
1
Center
Left
Front
1
Right
1
Left
1
Center
13. Sheets
1
Right
11. T-shirt
1
Front
12. Pillow case
10. Undershorts
9. Shirt
8. Bath towel
1
1
1
Rear
Center
Rear
7. Tabelcloth
1
Left
5. T-shirt
1
Front
3. Pillow case
1
Rear
6. Bath towel
4. Sheets
2. Pillow case
1. Bath towel
Total
1
1
1
30
39
38
37
36
Rear
23. Bath towel
22. Shirt
Illustration of loaded Wash Drum for standard test.
Right
Left
Right
17
TECHNICAL INFORMATION
TECHNICAL DATA
18
Width: 595 mm
Depth: 700 mm
Weight: 82 kg
Cylinder volume: 80 l
Max. washing capacity: 10 kg
Spin speed (rpm): 400-1400
Rated power: See type plate.
Heater output: See type plate.
Water pressure: 0,1-1 MPa
1-10 kp/cm2
10-100 N/cm2
Wash drum and liquid compartment material: Stainless steel
Outer casing material: Powder-coated and hot-galvanized sheet steel or stainless steel.
Water connection: 1.5 m pex pipe
Drain: 1.7 m polypropylene hose
INSTALLATION
POSITIONING THE WASHING MACHINE
The washing machine can be installed as a built-in or
freestanding unit. Place the machine on a firm surface
with easy access to the plug.
A. Built-in
The washing machine can be installed under a counter
top with a working height of 850-900 mm. Leave a 5 cm
space around the entire machine, including between the
rear edge of the top cover and the wall behind it.
Use only the supply hose supplied with the machine. Do
not re-use old hoses or other loose supply hoses.
DRAINAGE CONNECTION
The machine is supplied with a drainage hose attached,
which must be connected to a drain. See the examples
below. The height must be 600–900 mm above floor
level.
The lower position (600 mm) is always preferable.
Ensure that the drainage hose has no kinks.
B. Freestanding
The washing machine can be positioned beside or under
a tumble dryer.
ADJUSTING THE FEET
600--900 mm
Keep the noise that the machine produces to a minimum
by adjusting the feet so that the machine is steady and
balanced on the floor. Tighten the lock nuts.
Locking nut
The machine can also be connected to the drain via a
spigot connection. In this case the hose should also be
600-900 mm above the floor. The internal diameter of
the hole should be at least 18 mm.
• Cut the nipple
• Remove burrs from the hole.
See the illustration.
CONNECTION TO WATER SUPPLY
Water connection should be carried out by an
appropriately qualified person. Connect the machine
using the accompanying supply hose. Water pressure
should be 0.1–1MPa (approx. 1–10kp/cm2 ; 10–100N/
cm2). There should be a stopcock on the water pipe.
At least 18 mm
If the pipes are newly installed, it may be wise to
flush them through so that any dirt is washed away.
Otherwise, dirt can clog the filter in the machine’s water
intake and cut off cut off or reduce water flow to the
machine. Check for leaks.
19
INSTALLATION
ELECTRICAL INSTALLATION
Connect the machine by plugging it into an earthed
wall socket. The electrical wall socket must be placed
outside of the installation area to be easily accessible.
CAUTION!
If this appliance is supplied from a cord extensions
set or electrical portable outlet device, the cord
extension ser or electrical portable outlet device must
be positioned so that it is not subject to splashing or
ingress of moisture.
Connection on delivery
The machine comes with 1-Phase, 220-230 V, 50 Hz
with plug, heat output 2000 W W and fused 10 A. If a
residual current device is being used, this should be
type A.
NOTE!
Repairs and maintenance must be carried out by a
qualified professional.
20
BEFORE CONTACTING THE SERVICE DIVISION
BEFORE CONTACTING THE SERVICE
DIVISION
Before you contact the service division, make sure that
you know its model designation (1), type designation (2)
and serial number (3).
The model designation can be found on the panel. The
type designation and serial number can be found on the
type plate on the inside of the washer door.
NOTE!
For repairs and maintenance, original spare parts must
be used.
Model
1
2
TYPE
3
21
PROGRAMME CHART
Spin Speed
rpm
Max. load
(kg)
X
95
5
1400
10
117
2,98
2:56
X
60
5
1400
10
106
1,51
2:50
603)
3
1400
10
86
1,45
3:40
403),4)
3
1400
10
86
0,92
3:24
5. Every day wash
60
3
1400
10
81
1,61
1:49
6. Quick
40
2
1400
5
36
0,62
0:55
7. Easy Care
403)
2
1200
5
80
0,80
1:45
8. Synthetics
40
3
600
3
43
0,54
1:24
9. Wool / hand wash
30
3
600
3
94
0,67
0:55
1
1400
5
18
0,10
0:21
1400
5
0
0,08
0:16
1. Auto
Temp. °C
Program
Pre-wash
Number of
Rinses
Consumption values 1)
Water
Energy
Programme
consumption consumption time (approx.
(approx. liter) (approx. kWh) hrs and min.)
2)
2. Time program
3. Heavy
4. Normal
10. Rinse
11. Spin
12. Drain
0:01
13. Allegy cotton
60
5
1400
6,2
100
1,50
2:25
14. Alergy Synthetic
40
5
1200
3,1
95
0,95
1:50
15. Cleaning
90
1) Consumption data may vary from the given values depending on variations in water pressure,water hardness,water inlet temperature, room
temperature, fluctuations in the electricity, type and volume of the laundry and any extra options.
22
YOUR NOTES
23
QUICK GUIDE
1.
SORT THE WASHING, OPEN THE WASHING
MACHINE DOOR AND LOAD THE WASHING
2.
TURN ON THE MAIN POWER SWITCH
3.
ADD DETERGENT AND FABRIC SOFTENER,
AS REQUIRED
4.
SELECT A PROGRAMME AND ANY OPTIONS
5.
CLOSE THE WASHER DOOR AND PRESS
THE START BUTTON
Close zips.
Look at the item’s laundry label.
Sort the washing according to how soiled it is, colour and material.
NB! Place underwire bras in a laundry net.
The detergent packaging will have recommendations for how much
detergent you should use. With only a small amount of washing in the
machine, you can reduce the amount of detergent used.
You select a programme by turning the programme selector. The selected
programme is shown in the display.
The available options depend on the selected programme. If the option
is available for the selected programme, the symbol lights up when you
press the button.
The time remaining is shown in hours and minutes.
We reserve the right to make changes.
www.asko.com
WM 80.2
W8844 XL ECO
en (09-14)