Download DX-401A USER MANUAL - Techni-Lux

ISO 9001 CERTIFIED
www.liteputer.com.tw
DX-401A、DX-402A
4 Channel DMX Dimmer Pack
【USER MANUAL】
DX-401A [EUM-D]
Lite-Puter
ISO 9001 CERTIFIED
Chapter 1.
www.liteputer.com.tw
DX-401A / DX-402A Instruction
1-1 Feature
Maximum 10A per channel, total 30A!
DMX 512 signal.
2 sets of signal input/output, either 3 pin XLR connector or RJ11 telephone
jack.
LED display.
Automatic warm up function, protects loads and extend the life of bulbs.
Auto frequency tracking.
Most advanced 'C3' dimming curve.
DMX start address setting.
Channel dimming test.
256 steps resolution.
Faders for Manual operation. (DX-402A)
Equipped with clamp for truss hanging or desktop operation.
1-2 Specification
Power
AC 100-120V, AC 200-240V, 45-63Hz, 2 input
Output
Maximum 10A per channel, total 30A.
Signal input/ output
DMX512/ 1990
Signal connector
XLR 3Pin, 6P4C, RJ11telephone jack
Dimension
220(W) x 260(H) x 70(D) mm
Location
TRUSS hanging or desktop operation.
Weight
3 Kg
1
DX-401A [EUM-D]
Lite-Puter
ISO 9001 CERTIFIED
www.liteputer.com.tw
American Standard
DX-401A
DX-402A
AC IN 100-120V
CH.3.4
DMX OUT
DMX IN
4CH. DMX DIMMER PACK
10A PER CHANNEL
DX-401A
DX-402A
260
4CH. DMX DIMMER PACK
10A PER CHANNEL
CONTROL
OFF
10A PER CHANNEL MAX
DMX IN
MAIN
AC IN 100-120V
CH.1.2
260
DMX OUT
AC IN 100-120V
CH.3.4
68
CONTROL
OFF
10A PER CHANNEL MAX
ON
MAIN
AC IN 100-120V
CH.1.2
68
ON
CH1
CH1
CH2
CH3
CH2
CH3
CH4
CH4
FNC DMX
FNC DMX
68
73
220
68
73
220
European Standard
DX-401A
DX-402A
AC IN 200-240V
CH.3.4
DMX IN
DMX OUT
DMX IN
4CH. DMX DIMMER PACK
10A PER CHANNEL
DX-401A
DX-402A
260
4CH. DMX DIMMER PACK
10A PER CHANNEL
CONTROL
OFF
10A PER CHANNEL MAX
CH1
CH1
CH2
CH3
MAIN
AC IN 200-240V
CH.1.2
260
DMX OUT
CONTROL
OFF
AC IN 200-240V
CH.3.4
68
10A PER CHANNEL MAX
ON
MAIN
AC IN 200-240V
CH.1.2
68
ON
CH2
CH3
CH4
CH4
FNC DMX
220
FNC DMX
68
73
220
2
68
73
DX-401A [EUM-D]
Lite-Puter
ISO 9001 CERTIFIED
www.liteputer.com.tw
T4 ( IEC Standard )
DX-401A
DX-402A
AC IN 200-240V
CH.3.4
DMX OUT
ON
AC IN 100-120V
CH.3.4
CONTROL
OFF
68
10A PER CHANNEL MAX
MAIN
AC IN 200-240V
CH.1.2
10A PER CHANNEL MAX
DMX IN
DMX OUT
DX-401A
4CH. DMX DIMMER PACK
10A PER CHANNEL
DX-402A
260
CH1
CH1
CH2
CH3
MAIN
AC IN 100-120V
CH.1.2
DMX IN
260
4CH. DMX DIMMER PACK
10A PER CHANNEL
CONTROL
OFF
68
ON
CH2
CH3
CH4
CH4
FNC DMX
FNC DMX
68
73
220
68
73
220
1-3 DX-401A / DX-402A Real Panel
2
7
1
ON
AC IN 100-120V
CH.3.4
PUSH
CONTROL
OFF
10A PER CHANNEL MAX
1
2
2
1
3
3
1:GND
2:Data3:Data+
1.
2.
3.
4.
5.
6.
7.
DMX OUT
DMX IN
6
5
4
MAIN
AC IN 100-120V
CH.1.2
4 3 2 1 4 3 21
1:V+12V
2:Data+
3:Data4:GND
3
Dual AC power input 15A Per Socket
Control AC switch
DMX signal input (6P4C Phone jack)
DMX signal output (6P4C Phone jack)
DMX signal input (3 PIN cannon plug)
DMX signal output(3 PIN cannon plug)
Trip type circuit breaker, 10A MAX
3
DX-401A [EUM-D]
Lite-Puter
ISO 9001 CERTIFIED
www.liteputer.com.tw
1-4 Wiring
CAUTION:
The wire & connectors used must follow the local government and
other applicable rules and electrical regulations!
12 AWG : 20A
14 AWG : 15A
16 AWG : 13A
18 AWG : 10A
4
DX-401A [EUM-D]
Lite-Puter
ISO 9001 CERTIFIED
Chapter 1.
2-1
www.liteputer.com.tw
DX-401A / DX-402A Instruction
Standard DMX512 Signal
This point flashing when receiving DMX
2-2
DMX start address setting
STEP-1 holding【DMX】, press【▲】or【▼】to find the start address.
【▲】: move 1 number forward : up to Channel 512
【▼】: move 1 number backward :down to Channel 1
DX-401A /DX-402A is a 4 channel dimmer pack so when setting this unit:
as d. 0 0 1, the output is from Channel 1 Channel 4.
as d. 0 0 5, the output is from Channel 5 Channel 8.
It is allowed for setting more than 1 piece of DX-401A/DX-402A at the
same start address.
2-3
Dimming/Switching setting
STEP-1 press【DMX】key into DMX status
STEP-2 press and hold the【FNC】key for 3 sec.
Default setting：all channel
are dimming mode
5
DX-401A [EUM-D]
Lite-Puter
ISO 9001 CERTIFIED
www.liteputer.com.tw
STEP-3 press【FNC】key to select channel
STEP-4 press【▲】or【▼】to select dimming mode or switching mode
(dimming)
2-4
(Switching)
warm up setting (0…6%)
STEP-1 press【FNC】key
STEP-2 press【FNC】key to select the setting channel, EX :select channel 1
STEP-3 press【▲】,【▼】key to adjust
Channel 1 set on 6% for warm up
2-5
Bypass Full On
STEP-1 Selecting the channel for instant play
ex：Select Channel 1.
Hold the【CH-1】key for full on & it will come back to original dimming level when your
finger off the key.
2-6
Monitoring the dimming level of every channel
STEP-1 Enter DMX status, Hold【DMX】
STEP-2 Selecting the monitoring channel
6
DX-401A [EUM-D]
Lite-Puter
ISO 9001 CERTIFIED
www.liteputer.com.tw
ex.：(【▲】 Channel increasing 【▼】 Channel decreasing)
showing the brightness of the selected channel
Showing channel 1, 68%.
Press【DMX】key to cancel the setting.
DMX ADDRERSS will be displayed automatically after 10 minutes.
2-7
Dimming manually by fader (DX-402A)
ex.: Adjust the【VR-1 ~VR-4】, you can dim the Channel 1~ Channel 4 directly.
P.S. The high dimming value output when 2 signals (console V.S. manual
fader) has been received.
2-8
Back to DMX ADDRESS display
Press【DMX】key in any conditions or automatically back to show DMX address when
none key has been touched within 10 minutes.
7
DX-401A [EUM-D]
Lite-Puter