Download VIDEO ADAPTERS AND ACCELERATORS
Transcript
Color profile: Generic CMYK printer profile Composite Default screen Bigelow / Troubleshooting, Maintaining & Repairing PCs / Bigelow / 2686-8 / Chapter 43 TROUBLESHOOTING VIDEO ADAPTERS 1565 SYMPTOM 43-38 The computer locks up or crashes when starting an .AVI file This problem is encountered frequently as computer users first begin to try multimedia applications. Rather than being a problem with the video board specifically, the trouble is often due to using an outdated version of Video for Windows. Make sure to use Video for Windows 1.1E or later. Video for Windows can be downloaded from the Diamond Multimedia FTP site at; ftp://ftp.diamondmm.com/pub/misc/ vfw11e.exe. You may also need to edit the [DrawDib] section of the WIN.INI file and add an entry that says; DVA=0. If no [DrawDib] section is present, you can add it. Remember to restart Windows after making any changes. You may also be able to correct this type of problem by upgrading to Windows 98/SE, which should contain many of the very latest drivers and support components. SYMPTOM 43-39 The computer is running very slowly (poor performance), and the hard drive light is continuously lit This problem is particularly apparent with Diamond Edge 3D video boards on systems with more than 16MB of RAM. The Diamond Edge 3D board comes with both 1MB and 6MB MIDI bank files. Diamond recommends that you use only the 6MB bank file on systems with over 16MB of RAM. To change the size of the MIDI bank file being used: 1 Right-click on My Computer and choose Properties. 2 Open the System Control Panel and click on the Device Manager tab. 3 Click on the (+) symbol beside the “Sound, Video, and Game Controller” line. 4 Highlight “Diamond EDGE 3D PCI Multimedia Device,” click on Properties, and the click on Settings. 5 You will then see the 1MB and 6MB MIDI bank selection. Select the 6MB option, choose OK, and restart your computer when prompted. You notice that .AVI files have distorted colors or “grainy” playback This symptom usually occurs when playing 8-bit .AVI files that are not supported by DCI and can usually be corrected by disabling the accelerated video playback features of the video board. For example, the older Diamond ViperPro Video board is noted for this problem, and you would need to edit the COPRO.INI file located in the \windows directory. In the [VCP] area, change the VCPEnable= line to OFF. Save the .INI file and restart Windows. SYMPTOM 43-40 SYMPTOM 43-41 The PCI video board will not work under Windows unless the system’s PCI SCSI devices are disconnected This type of problem occurs only on certain combinations of PCI system hardware. For example, this type of symptom has been documented using Phoenix BIOS 4.04 and a UMC8810P-AIO motherboard on systems with an NCR SCSI controller and SCSI devices. You can often correct such problems by correcting the Advanced System Setup in CMOS. Start the CMOS Setup, go to the Advanced System Setup, and select PCI Devices. Set up the PCI slot for the SCSI controller as IRQ9 and LEVEL edge select. The slot for the video board should have the IRQ set to NONE, and LEVEL edge select. Change the Base Memory Address from 0080000000 to 0081000000. SYMPTOM 43-42 There are boot problems when a new video board is installed Typical symptoms include no video or eight beeps when the system is turned on. This problem is usually the result of an outdated system BIOS that is not capable of detecting the particular video chipset in use—the BIOS interprets this condition as meaning that there is no video board in the system, and an error is generated accordingly. Contact the motherboard manufacturer (or PC maker) for an updated system BIOS. Most BIOS versions dated after the fall of 1994 should be able to detect most modern video chipsets. P:\010Comp\Bigelow\686-8\ch43.vp Friday, July 21, 2000 9:51:07 AM 43