Download User Manual - Touch Screens Inc.

SL/IL Series
Digital Signage
User Manual
Disclaimer
BenQ Corporation makes no representations or warranties, either expressed or
implied, with respect to the contents of this document. BenQ Corporation reserves the
right to revise this publication and to make changes from time to time in the contents
thereof without obligation to notify any person of such revision or changes.
Copyright
Copyright 2014 BenQ Corporation. All rights reserved. No part of this publication may
be reproduced, transmitted, transcribed, stored in a retrieval system or translated into
any language or computer language, in any form or by any means, electronic, mechanical,
magnetic, optical, chemical, manual or otherwise, without the prior written permission
of BenQ Corporation.
Table of Contents
3
Table of Contents
Disclaimer..............................................................................
Copyright...............................................................................
Safety warnings and precautions ......................................
Important safety instructions............................................
2
2
5
6
Notes on the LCD panel of this display..................................... 6
Safety notice for remote control................................................. 7
Battery safety notice ....................................................................... 7
BenQ ecoFACTS.............................................................................. 8
Package contents ................................................................. 9
Optional accessory.......................................................................... 9
Setting up the display ........................................................ 10
Mounting the display.................................................................... 10
Parts of the display and their functions ........................ 13
Front panel .....................................................................................
Rear panel .....................................................................................
Input/output terminals.................................................................
Remote control.............................................................................
Using the remote control ...........................................................
13
13
15
17
18
Connection ......................................................................... 20
Connecting audio/video signals ................................................. 20
Connecting the touch module (IL series only) ...................... 27
Connecting power........................................................................ 28
Using the touch screen (IL series only)........................ 29
Supported operating systems .................................................... 32
Important instructions for using the touch screen............... 33
Basic operations................................................................. 34
Turning the display on or off .....................................................
Locking/unlocking the controls .................................................
Switching input signals .................................................................
Adjusting audio volume level .....................................................
34
34
34
34
4
Table of Contents
Network connection ........................................................ 35
Connecting to a LAN................................................................... 35
Controlling the display................................................................. 35
The OSD (On-Screen Display) menu ........................... 37
OSD menu overview ...................................................................
Operations in the OSD menu....................................................
Picture menu .................................................................................
Sound menu....................................................................................
Screen menu ..................................................................................
Setting menu ..................................................................................
37
38
39
40
41
45
Multimedia OSD operation............................................. 48
Multimedia buttons on the remote control ........................... 48
Viewing files.................................................................................... 49
Menu system .................................................................................. 60
Product information.......................................................... 64
Specifications..................................................................................
Dimensions.....................................................................................
Supported input signal resolution .............................................
Supported PAP input signal combination.................................
64
70
75
77
Troubleshooting ................................................................. 78
Safety warnings and precautions
5
Safety warnings and precautions
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the
presence of uninsulated "dangerous
voltage" within the product's enclosure
that may be of sufficient magnitude to
constitute a risk of electric shock to
persons.
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
THIS EQUIPMENT MUST BE
GROUNDED
To ensure safe operation, the three-pin
plug must be inserted only into a
standard three-pin power outlet which
is effectively grounded through normal
household wiring. Extension cords
used with the equipment must have
three cores and be correctly wired to
provide connection to the ground.
Wrongly wired extension cords are a
major cause of fatalities.
The fact that the equipment operates
satisfactorily does not imply that the
power outlet is grounded or that the
installation is completely safe. For your
safety, if you are in any doubt about
the effective grounding of the power
outlet, please consult a qualified
electrician.
• The mains plug of the power supply cord shall remain readily operable. The AC
receptacle (mains socket outlet) shall be installed near the equipment and shall be easily
accessible. To completely disconnect this equipment from the AC mains, disconnect the
power cord plug from the AC receptacle.
• Do not place this display on an uneven, sloping or unstable surface (such as a trolley)
where it may fall and cause damage to itself or others.
• Do not place this display near water, like a spa or pool, or in a position which will allow
the splashing or spraying of water onto the display, like in front of an open window
where rain water may enter.
• Do not install this display in a confined space without proper ventilation and air
circulation, such as in a closed cabinet. Allow proper space around the display for
dissipating heat inside. Do not block any openings and vents on the display. Overheating
may result in hazards and electric shock.
• Installation of this display should only be performed by a qualified technician. Failure to
install this display properly may cause injuries and damages to the personnels and the
display itself. Check the installation regularly and maintain the display periodically to
ensure the best working condition.
• Use only the accessories approved or recommended by the manufacturer to mount this
display. Using wrong or unsuitable accessories may cause the display to fall and result in
serious personal injuries. Make sure that the surface and fixing points are strong enough
to sustain the weight of the display.
• To reduce the risk of electric shock, do not remove covers. No user serviceable parts
inside. Refer servicing to qualified service personnel.
• To prevent personal injuries, mounting the display or installing desktop stands is
required before use.
6
Important safety instructions
Important safety instructions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding-type plug
has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury
from tip-over.
Unplug this apparatus during lightning storms or when unused for long
periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
Notes on the LCD panel of this display
• The Liquid Crystal Display (LCD) panel of this display has a very thin protective layer of
glass which is liable to marking or scratching, and cracking if struck or pressured. The
liquid crystal substrate is also liable to damage under excessive force or extreme
temperatures. Please handle with care.
• The response time and brightness of the LCD panel may vary with the ambient
temperature.
• Avoid placing the display in direct sun or where direct sun or spot lighting will shine
onto the LCD panel, as the heat may damage the panel and the external casing of the
display, and the bright light will make viewing the display more difficult than necessary.
• The LCD panel consists of individual pixels to display images and is manufactured
according to the design specifications. While 99.9% of these pixels work normally,
0.01% of the pixels may remain constantly lit (in red, blue or green) or unlit. This is a
technical limitation of the LCD technology and is not a defect.
• LCD screens, like plasma (PDP) and conventional CRT (Cathode Ray Tube) screens, are
also susceptible to 'screen burn-in' or 'image retention' which can be found on the
Important safety instructions
7
screen as visible fixed lines and shades. To avoid such damage to the screen, avoid
displaying still images (like On-Screen Display menus, TV station logos, fixed/inactive
text or icons) for more than two hours. Change the aspect ratio from time to time. Fill
the entire screen with the image and eliminate the black bars whenever possible. Avoid
displaying images in 4:3 aspect ratio over a long period of time, otherwise there may be
visible burn marks on the screen as two vertical lines.
If display of a still image is required, it is recommended to enable Anti Image
Retention under the Setting and Advanced menu.
• Note: Under certain circumstances, condensation may occur on the inner side of the
cover glass, it's a natural phenomenon and will not affect the operation of the display.
This condensation will usually disappear after around 2 hours of normal operation.
Safety notice for remote control
• Do not put the remote control in the direct heat, humidity, and avoid fire.
• Do not drop the remote control.
• Do not expose the remote control to water or moisture. Failure to do so could result
in malfunction.
• Confirm there is no object between the remote control and the remote sensor of the
product.
• When the remote control will not be used for an extended period, remove the
batteries.
Battery safety notice
The use of the wrong type of batteries may cause chemical leaks or explosion. Please
note the following:
• Always ensure that the batteries are inserted with the positive and negative terminals in
the correct direction as shown in the battery compartment.
• Different types of batteries have different characteristics. Do not mix different types.
• Do not mix old and new batteries. Mixing old and new batteries will shorten battery life
or cause chemical leaks from the old batteries.
• When batteries fail to function, replace them immediately.
• Chemicals which leak from batteries may cause skin irritation. If any chemical matter
seeps out of the batteries, wipe it up immediately using a dry cloth, and replace the
batteries as soon as possible.
• Due to varying storage conditions, the battery life for the batteries included with your
product may be shortened. Replace them within 3 months or as soon as you can after
initial use.
• There may be local restrictions on the disposal or recycling of batteries. Consult your
local regulations or waste disposal provider.
8
Important safety instructions
BenQ ecoFACTS
BenQ has been dedicated to the design and development of greener product as part of
its aspiration to realize the ideal of the "Bringing Enjoyment 'N Quality to Life" corporate
vision with the ultimate goal to achieve a low-carbon society. Besides meeting
international regulatory requirement and standards pertaining to environmental
management, BenQ has spared no efforts in pushing our initiatives further to incorporate
life cycle design in the aspects of material selection, manufacturing, packaging,
transportation, using and disposal of the products. BenQ ecoFACTS label lists key ecofriendly design highlights of each product, hoping to ensure that consumers make
informed green choices at purchase. Check out BenQ's CSR Website at http://
csr.BenQ.com for more details on BenQ's environmental commitments and
achievements.
Package contents
9
Package contents
Open the sales package and check the contents. If any item is missing or damaged, please
contact your dealer immediately.
LCD display
Power cord
AAA batteries
Quick start guide
D-Sub (15-pin)
cable
Remote control
USB cable (IL series only)
• The type of power cord supplied may differ from that illustrated depending on your region of
purchase.
• Before discarding the package, check that you haven't left any accessories inside the box.
• Dispose of packaging materials wisely. You can recycle the cardboard carton. Consider storing
the package (if possible) for future transport of the display.
• Do not leave plastic bags within reach of young children or babies.
Optional accessory
In addition to the items that come with the standard package, the following optional
accessory is also available separately:
Desktop stand
10
Setting up the display
Setting up the display
Mounting the display
You can install the display on a vertical surface with a suitable wall mounting bracket or
on a horizontal surface with the optional desktop stands. Please pay attention to the
following notes during installation:
• This display should be installed by at least two adult persons. Attempting to install this
display by only one person may result in danger and injuries.
• Refer the installation to qualified technicians. Improper installation may cause the
display to fall or malfunction.
Installing the display on a wall
1. Place a clean, dry and lint-free cloth on a flat, horizontal and object-free surface.
Make sure that the size of the cloth is larger than the display.
2. Gently lay the display on the cloth with the LCD screen facing down.
3. Remove the desktop stands from the display if installed.
4. Identify the wall mounting screw 42"/46"
*Screw type: M6
holes on the back of the display
400mm
as shown in the illustration.
200mm
65"
400mm
*Screw type: M8
400mm
Setting up the display
5. Install the wall mounting bracket
on the display and attach the
display to the wall according to
the mounting bracket’s
instructions. The length of the
screw should exceed the
thickness of the wall mounting
bracket by at least 10 mm. Make
sure that all screws are
tightened and secured properly.
(Recommended torque: 470 635N•cm). The mounting means
should be strong enough to bear
the weight of the display.
Thickness of the
wall mounting
bracket
LCD display
• To maintain proper ventilation, keep at least 10 mm of
clear space from the back cover of the display to the
wall.
• Please consult a professional technician for wall mount
installations. The manufacturer accepts no liability for
installations not performed by a professional technician.
• The AC IN/OUT socket should be on top of connectors
when rotating your display.
10 mm
(0.39")
10mm
(0.39")
11
12
Setting up the display
Installing the optional desktop stands
1. Place a clean, dry and lint-free cloth on a flat, horizontal and object-free surface.
Make sure that the size of the cloth is larger than the display.
2. Gently lay the display on the cloth with the LCD screen facing down.
3. Place the desktop stands on the
Screw Type: M6 x 10 mm
42"/46"
display as illustrated.
Torque: 10
4. Use the screws and a suitable
screwdriver to secure the stands on
the display.
65"
Screw Type: M8 x 15 mm
Torque: 25
The IL Series displays are not suggested for flip table application (long time usage as horizontal
position).
Parts of the display and their functions
Parts of the display and their functions
Front panel
SL420/IL420
1
IL650
1
Rear panel
SL420/IL420
2
3
SL460
4
1
4
5
1
IL460
6
IL650
2
3
4
4
5
6
13
14
No.
Parts of the display and their functions
Name
Description
3
• Receives command signals from the remote control.
Remote control sensor / • Detects ambient lighting conditions around the display and
adjusts screen brightness automatically when the Ambient
Ambient light sensor /
Light Sensor function is activated.
Power indicator
• Indicates the operating status of the display:
- Lights up green when the power is turned on.
- Lights up red when the display is turned off.
- Lights up red when the display is in Power Save High
mode.
- Flashes red when the display is in Power Save Low
mode.
- Off when the main power is turned off.
ENTER/VIDEO
• Selects a video source.
SOURCE
• Confirms your selection or enters a submenu in the OnScreen Display (OSD) menu.
MENU
Opens or closes the OSD menu.
4
, , /-,/+
5
Power button
6
Power indicator
1
2
• Scrolls through settings and options in the OSD menu.
• /-,/+: Hot keys for audio volume adjustment.
Turns the display on or off.
Indicates the power status of the display:
- Lights up green when the power is turned on.
- Lights up red when the display is turned off.
- Lights up red when the display is in Power Save High
mode.
- Flashes red when the display is in Power Save Low
mode.
- Off when the main power is turned off.
Parts of the display and their functions
15
Input/output terminals
SL series
USB A
20
USB B
RJ-45
19
HDMI
17
DP
18
MULTI-MEDIA
21
RS-232C-OUT
DVI-IN
16
RS-232C-IN
15
14 13 12 11 10 9
8
7
6
5
14 13 12 11 10 9
8
7
6
5
3
2
1
3
2
1
19
18
IL650
17
16
IL420/IL460
15
No.
Name
4
Description
1
AC OUT
Relays the AC power from the AC IN jack to another display.
2
AC IN
Connects to a power outlet via the supplied power cord.
AC SWITCH ON/
OFF
USB
(IL series only)
SPEAKERS (R/L)
(Not for the IL650)
AUDIO OUT (R/L)
Turns on or off the main power.
AUDIO IN
(AUDIO2)
AUDIO IN
(AUDIO1)
Receives audio signals from an external device (such as a VCR or
DVD player).
Receives audio signals from an external device (such as a
computer).
3
4
5
6
7
8
Connects the USB cable from the display to a computer to use
the touch module.
Outputs audio signals to external speakers.
Outputs audio signals to an external device.
16
Parts of the display and their functions
14
VIDEO IN (SVIDEO)
VIDEO IN (YPbPr)
15
RS232C IN/OUT
16
DVI-IN
17
HDMI
18
DISPLAY PORT
Receives analog RGB signals from an external device (such as a
computer).
Outputs analog RGB signals from the VGA IN input to another
display.
Receives composite video signals from an external device (such as
a VCR or DVD player).
Outputs composite video signals from the AV IN input to another
display.
Receives S-Video signals from an external device (such as a VCR
or DVD player).
Receives component video (YPbPr) signals from an external
device (such as a DVD player, HDTV device or Laser disc player).
For external control and multi-display operation.
• RS232C IN: receives control signals from a computer or
another display.
• RS232C OUT: outputs control signals from the RS232C IN
input to another display.
Receives DVI signals from an external device (such as a
computer).
Receives HDMI signals from an external device (such as a Blu-ray
disc player).
Connects to a DisplayPort compatible device.
19
RJ-45
Connects to the RJ-45 port on your Ethernet or router.
USB B
(Mini B)
(SL series only)
USB A
(Type A)
(SL series only)
Connects to a computer for USB display.
9
VGA IN
10
VGA OUT
11
AV IN
12
AV OUT
13
20
21
Connects to a USB flash drive or WiFi dongle.
Parts of the display and their functions
Remote control
5
17
ENTER
Confirms your selection or save changes.
1
6
2
6
INFO
Shows the current input source and resolution.
7 Numeric buttons (1-9) /Input source
buttons
7
3
• Performs as numeric buttons when the OSD
menu is on.
• Performs as input source buttons when the OSD
menu is off.
8
9
4
10
5
• The HDMI-2 and SDI functions are not available with this
display.
• The MULTI-MEDIA function is only available with the SL
series.
8
MENU
Opens or closes the OSD menu.
11
1
ON/OFF
Turns the display on or off.
2
INPUT
Selects an input source.
3
EXIT/FREEZE
• Returns to the previous menu or closes
the OSD menu when the OSD menu is
on.
• Freezes the image when the OSD menu
is off. Press this button again or press
MENU to resume normal display.
4 / VOL- // VOL+
• Scrolls through settings and options in
the OSD menu.
• Turns down/up the volume.
9
Numeric button (0)/MUTE
• Performs as a numeric button when the OSD
menu is on.
• Turns on or off the mute function.
10 BLANK/
• Scrolls through settings and options in the OSD
menu when the OSD menu is on.
• Hides the image (the screen becomes blank)
when the OSD menu is off. Press this button
again or press MENU to resume normal display.
11
MULTI-MEDIA buttons
(SL series only) See "Multimedia OSD operation"
on page 48 for details.
(IL series only) The button functions are not
available with the display.
18
Parts of the display and their functions
Using the remote control
Installing remote control batteries
1. Open the remote control battery compartment
cover.
2. Insert the supplied batteries ensuring that the
positive and negative marked battery terminals match
the (+) and (-) marks in the battery compartment.
The supplied batteries are provided for your convenience so
that you can operate the display straight away. You should
replace them as soon as possible.
3. Refit the battery compartment cover.
Parts of the display and their functions
19
Remote control usage tips
• Point and aim the top front of the remote control directly at the display’s remote
control sensor window when you press the buttons.
• Do not let the remote control become wet or place it in humid environments (like
bathrooms).
• If the display’s remote control sensor window is exposed to direct sunlight or strong
light, the remote control may not operate properly. In this situation, change the light
source, readjust the angle of the display or operate the remote control from a location
closer to display’s remote control sensor window.
SL460
IL460
SL420/IL420
IL650
Max. 10 m
(32.8 feet)
20
Connection
Connection
Connecting audio/video signals
Pay attention to the following notes when you connect cables:
• Please turn off all devices.
• Familiarize yourself with the audio/video ports on the display and the devices you want
to use. Be aware that incorrect connections may adversely affect picture quality.
• Do not remove cables from the ports by pulling the cable itself. Always grasp and pull
the connectors at the end of the cable.
• Ensure that all cables are fully inserted and firmly seated.
Connecting the VGA input
1. Connect the VGA IN jack on the display to the VGA output jack on a computer using
a D-Sub (15-pin) cable.
2. Connect the computer’s audio output jack to the AUDIO IN (AUDIO1) jack on the
display using a suitable audio cable.
3. To view images from this input, press the VGA button on the remote control. To
select an appropriate audio source, see "Audio Source" on page 40 for details.
IL420/IL460
IL650
SL series
MULTI-MEDIA
RS-232C-OUT
RJ-45
USB A
USB B
DP
HDMI
DVI-IN
RS-232C-IN
D-Sub (15-pin) cable
Audio cable
Computer
The audio cable is not supplied and should be purchased separately.
Connection
21
Connecting the digital inputs
1. Connect the DVI-IN jack on the display to the DVI-D output jack on a computer
using a DVI-D cable. If the computer has an HDMI output jack, connect the computer’s HDMI output jack to the DISPLAY PORT/HDMI input jack on the display
using an HDMI cable or a DVI-D to HDMI conversion cable.
2. If needed, connect the computer’s audio output jack to the AUDIO IN (AUDIO1)
jack on the display using a suitable audio cable.
3. To view video image from this input, press the DVI or DP/HDMI-1 button on the
remote control. To select an appropriate audio source, see "Audio Source" on page
40 for details.
IL420/IL460
IL650
SL series
MULTI-MEDIA
RS-232C-OUT
RJ-45
USB A
USB B
DP
HDMI
DVI-IN
RS-232C-IN
DVI-D cable
Audio cable
DisplayPort
cable
HDMI
cable
Computer
The cables are not supplied and should be purchased separately.
22
Connection
Connecting the YPbPr component video input
1. Connect the VIDEO IN (YPbPr) jacks on the display to the component output jacks
on an A/V device (such as a VCR or DVD player) using a component video cable.
2. Connect the DVD player’s audio output jacks to the AUDIO IN (AUDIO2) jacks on
the display using a suitable audio cable.
3. To view video image from this input, press the YPbPr button on the remote
control. To select an appropriate audio source, see "Audio Source" on page 40 for
details.
IL420/IL460
IL650
SL series
MULTI-MEDIA
RS-232C-OUT
RJ-45
USB A
USB B
DP
HDMI
DVI-IN
RS-232C-IN
Component video cable
Audio cable
DVD player / VCR
The cables are not supplied and should be purchased separately.
Connection
23
Connecting the AV and S-Video inputs
1. Connect the VIDEO IN (S-VIDEO) or AV IN jack on the display to the output jack
on an A/V device (such as a VCR) using an appropriate video cable.
2. Connect the VCR’s audio output jacks to the AUDIO IN jacks on the display using a
suitable audio cable.
3. To view video image from this input, press the AV button on the remote control for
the AV signal, or press the INPUT button repeatedly for the S-Video signal. To
select an appropriate audio source, see "Audio Source" on page 40 for details.
IL420/IL460
IL650
SL series
MULTI-MEDIA
RS-232C-OUT
RJ-45
USB A
USB B
DP
HDMI
DVI-IN
RS-232C-IN
S-Video cable
AV cable Audio cable
DVD player / VCR
The cables are not supplied and should be purchased separately.
24
Connection
Connecting the multimedia inputs (SL series only)
To connect to a network, do one of the following steps.
• Take a RJ-45 cable and connect one end to the RJ-45 jack on the display and the other
end to the RJ-45 port on your Ethernet or router.
• Plug a wireless dongle to the USB A jack.
To connect to a computer directly:
Take a USB cable, connect the mini B plug to the USB B jack on the display and the type
A plug to a computer.
To view video image from the input, press MULTI-MEDIA on the remote control or
select MULTI-MEDIA from the source selection bar to access the multimedia OSD
system. See the "Multimedia OSD operation" on page 48 for details.
SL series
RS-232C-OUT
MULTI-MEDIA
RJ-45
USB A
1
USB B
DP
2
4
3
HDMI
DVI-IN
RS-232C-IN
1
USB flash drive
2
USB wireless dongle
3
USB cable
4
RJ-45 cable
The cables are not supplied and should be purchased separately.
Connection
25
Connecting external speakers (not for the IL650)
The built-in amplifier on the display allows you to output audio signals through external
speakers. Connect external speakers to the SPEAKERS (R/L) jacks on the display.
IL420/IL460 (not for the IL650)
SL series
MULTI-MEDIA
RS-232C-OUT
RJ-45
USB A
USB B
DP
HDMI
DVI-IN
RS-232C-IN
External speakers
You can use the remote control or the control panel on the display to adjust the volume.
26
Connection
Connecting multiple displays
You can connect multiple displays serially (daisy chain) to a computer for management.
The number of displays you can connect serially depends on the resolution of the input
signal you use.
Additional display
IL420/IL460
IL650
SL series
MULTI-MEDIA
RS-232C-OUT
RJ-45
USB A
USB B
DP
HDMI
DVI-IN
RS-232C-IN
RS-232C
cable
AV
cable
D-Sub (15pin) cable
SL series
MULTI-MEDIA
RS-232C-OUT
RJ-45
USB A
USB B
DP
HDMI
DVI-IN
RS-232C-IN
IL650
IL420/IL460
The first display
• This RS-232C daisy chain application requires an RS-232C port equipped computer.
• Use RS-232C serial null modem cables for daisy chain application.
• Avoid using HDCP source for daisy chain application
Connection
27
Connecting the touch module (IL series only)
Connect the USB (type B) jack on the display to the USB port of a computer using the
supplied USB cable. The touch module of the display supports easy Plug-and-Play
operation. There is no need to install additional drivers on the computer.
IL420/IL460
IL650
• Avoid blocking the touch screen frame (where sensors are located) when initiating the touch
module.
• It is highly recommended that you connect the display to the PC or laptop directly. Avoid
connecting the display to a face plate device which may cause failures in touch operations.
• If any ghost image occurs, please try to un-plug and then re-plug all USB cables. If the failure
image still exists, use another USB type B to A cable.
28
Connection
Connecting power
1. Plug one end of the power cord into the AC IN jack on the display and the other end
into an appropriate power outlet (if the outlet is switched, turn on the switch).
2. Press the power switch to turn on the main power.
2
1
• The supplied power cord is suitable for use with 110-240V AC power only.
• The power cord and outlet illustrated may differ from the ones used in your region.
• Only use an appropriate power cord for your region. Never use a power cord which appears
damaged or frayed, or change the plug type on the power cord.
• Be aware of the power loading when you use extension cords or multiple outlet power boards.
• There are no user serviceable parts in this display. Never unscrew or remove any covers.
There are dangerous voltages inside the display. Turn off the power and unplug the power cord
if you intend to move the display.
Using the touch screen (IL series only)
29
Using the touch screen (IL series only)
You can use the optical touch screen to control your operating system. The touch screen
can emulate basic mouse functions and supports multi-touch functions for Windows 7/
8*. The following table shows a list of gestures you can use on the touch screen.
• Ensure that you have installed the USB cable on the display to a computer.
• *Multi-touch functions are only supported by Windows 8, Windows 7 - Home Premium,
Professional, Enterprise and Ultimate versions. For Windows XP, Windows Vista and Windows
7 - Starter and Home Basic versions, multi-touch is not supported.
• Windows is a registered trademark of Microsoft Corporation in the United States and other
countries.
OS functions
Gesture actions
For Windows XP, Windows Vista and Windows 7
Click
Tap the screen once.
Double-click
Tap the screen twice.
Right-click
1. Press on the target.
2. Hold and wait for a blue ring to appear.
3. Release your finger.
Drag
Drag one finger left or right.
30
Using the touch screen (IL series only)
OS functions
Gesture actions
For Windows Vista and Windows 7
Selection
Drag one finger left or right.
Pan up / Pan down / Back /
Forward
Quickly drag your finger (Flick) in a desired direction.
Multi-touch functions
For Windows 7 - Home Premium, Professional, Enterprise and Ultimate versions
Right-click
1. Press on the target.
2. Tap the screen with another finger.
3. Release the second finger.
Scrolling
Drag one or two fingers up or down.
or
Zoom
Move two fingers apart or toward each other.
Using the touch screen (IL series only)
OS functions
31
Gesture actions
Supported by specific
applications
• Move two fingers in opposing directions.
• Use one finger to pivot around another.
Supported by specific
applications
Tap two fingers simultaneously.
The target should be the midpoint between
the fingers.
For Windows XP, Windows Vista and Windows 7
Wakeup from Windows
Press and hold for 4
sleep mode (S3)
seconds.
Gesture
Description
For Windows 8
Press and hold to learn
This touch interaction causes detailed information or teaching
visuals (for example, a tooltip or context menu) to be displayed
without a commitment to an action. Anything displayed this way
should not prevent users from panning if they begin sliding their
finger.
Tap for primary action
Tapping on an element invokes its primary action, for instance
launching an application or executing a command.
Slide to pan
Slide is primarily used for panning interactions but can also be
used for moving, drawing or writing. Slide can also be used to
target small, densely packed elements by scrubbing (sliding the
finger over related objects such as radio buttons).
32
Using the touch screen (IL series only)
Gesture
Description
Swipe to select, command, and move
Sliding the finger a short distance, perpendicular to the panning
direction, selects objects in a list or grid (ListView and
GridLayout controls). Display the AppBar with relevant
commands when objects are selected.
Pinch and stretch to zoom
While the pinch and stretch gestures are commonly used for
resizing, they also enable jumping to the beginning, end, or
anywhere within content with Semantic Zoom. A
SemanticZoom control provides a zoomed out view for showing
groups of items and quick ways to dive back into them.
Turn to rotate
Rotating with two or more fingers causes an object to rotate.
Supported operating systems
OS
IL420/IL460
6 touch points (plug & play)
• Windows XP: 1 point
• Windows 7 (Starter, Home Basic): 1
point
Windows • Windows 8
6 touch points (driver installation
required)
• 10.4 ~ 10.9
6 touch points (driver installation
required)
Linux
• Fedora 15
• Ubuntu 12.10
6 touch points (source code integration
Android
required)
Mac
IL650
2 touch points (plug & play)
• Windows XP: 1 point
• Windows 7 (Starter, Home Basic): 1
point
• Windows 8
• Windows embedded standard 7 (tablet
PC package driver installation required)
• Windows embedded standard 8 (tablet
PC package driver installation required)
2 touch points (driver installation
required)
• 10.4 ~ 10.9
1 touch point (driver installation
required)
• Linux kernel version 3.9.2
• X-Window version 1.13 & previous
2 touch points (source code integration
required)
If you are using the display with Windows embedded operating systems, ensure that the tablet PC
package driver has been installed by the PC vendor.
Using the touch screen (IL series only)
33
Important instructions for using the touch screen
Please clean the frame when there is sign of malfunction on the touch screen.
• Before you clean the screen, make sure the display is turned off, and unplug the power
cord.
• Remove dust or dirt from the screen and the infrared plastic filter periodically. It is
suggested using a small amount of alcohol to clean the infrared plastic filter.
• To avoid damage to the screen, never use any type of abrasive materials to wipe the
screen.
• Use a neutral detergent to clean the touch screen. Avoid using detergents with erosive
substance, such as banana oil or ammonia.
• Moisten a clean, soft, lint-free cloth with a neutral detergent and then clean the touch
screen.
• Do not spray a detergent on the screen surface or the body directly. It may result in a
short circuit to the touch screen.
• Keep the touch screen out of direct sunlight or spotlights.
34
Basic operations
Basic operations
Turning the display on or off
To turn on or off the display, press the power button on the
display’s control panel or on the remote control.
• The display’s standby mode still consumes power. To completely cut off power supply, set the
power switch to the off position or disconnect the power cord from the power outlet.
• The display follows the VESA approved DPM Power Management function. The power
management function is an energy saving feature that automatically reduces the display’s power
consumption when the keyboard or the mouse has not been used for a fixed period.
Locking/unlocking the controls
You can lock/unlock the control panel to prevent unwanted or accidental operations.
• Control panel buttons
To lock/unlock the control panel buttons, press and hold /- and /+ on the control
panel simultaneously for 5 seconds. Once locked, the control panel buttons do not
function unless unlocked.
• Remote control (IR) functions
To lock/unlock the remote control (IR) functions, press and hold MENU and /- on the
control panel for 5 seconds. Once locked, the display does not respond to any remote
control operations unless unlocked.
To lock/unlock both the control panel and remote control buttons, press for 5
seconds, and then ENTER on the remote control. Once locked, the control panel and
remote control buttons do not function unless unlocked.
Switching input signals
Press the INPUT button or those signal selection buttons on the remote control or the
INPUT button on the control panel to select an input signal.
Adjusting audio volume level
Press /- or/+ on the control panel or VOL+/VOL- on the remote control to adjust
the volume.
Network connection
35
Network connection
Connecting to a LAN
To set the display to connect to a local area network:
1. Connect a RJ45 cable to the corresponding ports on the display and your LAN
switch or router.
2. Enter the OSD menu Setting > Control Setting. Select LAN.
3. Enter the next OSD menu Setting > Network Settings.
If you are in a DHCP environment, select DHCP > Execute and press ENTER.
Once done, the IP Address, Subnet Mask, Default Gateway, Primary DNS,
and Secondary DNS settings will be displayed.
If you are not in a DHCP environment, select Manual > Execute and press
ENTER. Contact your ITS administrator for information on the IP Address,
Subnet Mask, Default Gateway, Primary DNS, and Secondary DNS settings
and enter it accordingly.
4. To save the settings and return to the previous menu, highlight Execute and press
ENTER on the remote control.
Controlling the display
Once you have the correct IP address for your display and the display is on or in standby
mode, you can use any computer that is on the same local area network to control the
display.
• You cannot control the display via the RS-232C connector when LAN control is in use.
• It is recommended that you use Internet Explorer versions 7.0 or higher browser.
1. Enter the IP address of the display in the address bar of your browser and press
Enter.
2. The setting page appears.
• INFORMATION: Shows information of the display. It is for information only. There are
no items that can be set.
• PICTURE & SOUND: Provides options for picture and sound adjustments.
• SCREEN: Provides options related to display adjustments.
• SETTING: Provides options for advanced display adjustments.
• MAIL REPORT: Provides options for setting up email accounts to receive status or
error reports sent from the display.
• NETWORK: Provides options for manually setting the display’s IP address or obtaining
an IP address from a DHCP server.
Make sure the Setting > Control Setting menu is set to LAN, and the Setting > Power
Save menu is set to Low or Off if you would like to turn on the display from a web page.
36
Network connection
IP
address
Main
menus
The OSD (On-Screen Display) menu
The OSD (On-Screen Display) menu
OSD menu overview
Menu name
Picture
Sound
Screen
Setting
Options/functions
• Picture Mode
• Backlight
• Contrast
• Brightness
• Chroma
• Phase
• Sharpness
• Color Temp.
• Noise Reduction
• Film Mode
• Reset
• Sound Mode
• Treble
• Bass
• Balance
• Surround
• Speaker
• Audio Source
• Reset
• PAP Setting
• Display Wall
• Aspect
• Adjust Screen
• Freeze
• Touch Feature
• Language
• Schedule
• Power Save
• Control Setting
• Network Settings
• Set Monitor ID
• HDMI Control
• Advanced
• Information
• All Reset
Some options are only available when a certain input signal source is selected.
See page
39
40
41
45
37
38
The OSD (On-Screen Display) menu
Operations in the OSD menu
Using the control panel buttons
Using the remote control
1. Press MENU to open the OSD menu.
1. Press MENU to open the OSD menu.
ENTER
VIDEO
SOURCE
2. In the OSD menu, press or to
select an item.
2. Press or to select an item.
ENTER
VIDEO
SOURCE
3. Press ENTER/VIDEO SOURCE to
confirm selections.
3. Press ENTER to confirm selections.
ENTER
TER
VIDEO
SOURCE
4. Press or to select a feature and
press or to adjust settings. Press
ENTER/VIDEO SOURCE to save
changes.
4. Press and to select a feature and
press or to adjust settings. Press
ENTER to confirm changes.
ENTER
TER
VIDEO
SOURCE
5. Press MENU to close the OSD menu.
ENTER
VIDEO
SOURCE
5. Press MENU to close the OSD menu.
The OSD (On-Screen Display) menu
39
Picture menu
Picture
Picture Mode
Backlight
Standard
100
50
50
25
25
10
Cool
Mid
Auto
Contrast
Brightness
Chroma
Phase
Sharpness
Color Temp.
Noise Reduction
Film Mode
Reset
:Move
Name
Picture Mode
Backlight
ENTER :Enter
EXIT :Exit
Description
Sets the display mode.
Adjusts the backlight intensity for the screen.
This feature is not available if the Ambient Light Sensor or Adaptive Contrast
function is set to On.
Contrast
Brightness
Chroma
Phase
Sharpness
Color Temp.
Noise
Reduction
Film Mode
Adjusts the image contrast.
Adjusts the image brightness.
Adjusts the color intensity of the image.
Adjusts the color tint of the image.
Adjusts the image sharpness.
Adjusts the color temperature.
Reduces electrical image noise caused by different media players.
Optimizes the screen display automatically by detecting picture content and
applying a reverse 3-2 or 2-2 pull-down process. The picture will be clearer
and more natural.
• This function is not available when displaying Picture and Picture (PAP).
• This function may not be correctly processed depending on the input signal.
Reset
Resets all settings in the Picture menu.
40
The OSD (On-Screen Display) menu
Sound menu
Sound
Sound Mode
Treble
Bass
Balance
Surround
Speaker
Audio Source
Reset
:Move
Name
Standard
0
0
Center
Off
Internal
Audio1
EXIT :Exit
ENTER :Enter
Description
Sound Mode Adjusts the sound output from the speakers.
Dynamic: Enhances treble and bass.
Standard: Flat settings.
Custom: Recalls the customized settings.
Treble
Adjusts the audio treble.
Bass
Adjusts the audio bass.
Balance
Adjusts the audio balance.
Surround
Turns the surround mode on or off.
Speaker
Sets the audio source.
Line-out: Selects the audio output source from AUDIO OUT (R/L) on the
rear connector panel.
External (Not for the IL650): Selects the audio output source from
SPEAKERS (R/L) on the rear connector panel.
Internal: Select the audio output source from the internal speakers.
Audio
Sets the audio input source.
Source
MULTI-MEDIA
RJ-45
USB A
USB B
DP
HDMI
DisplayPort HDMI
Reset
DVI-IN
Audio1 Audio2
Multi-Media (SL series only): The audio source is from the built-in multimedia board.
Resets all settings in the Sound menu.
The OSD (On-Screen Display) menu
41
Screen menu
Screen
PAP Setting
Display Wall
Aspect
Adjust Screen
Freeze
Touch Feature
:Move
Off
Off
ENTER :Enter
Name
PAP Setting
(Picture and
Picture)
Full
EXIT :Exit
Description
• PAP: Turns on or off the PIP (Picture in Picture) and PBP (Picture by
Picture) functions.
• Active Picture: For the PIP, selects the main or sub picture to operate.
For the PBP, selects the left or right picture to operate. Swaps the main/
sub or left/right pictures.
• Picture Size: Changes the size of the sub picture.
PIP mode
Small
Large
PBP mode
Aspect Ratio
4:3
16:9
Width Height Width Height
304
225
400
225
456
338
600
338
Unit: pixel
• In PIP mode, when the aspect ratio of the sub
picture’s source signal is 4:3 and its Aspect
setting is set to Full 1 or Real, the aspect ratio
of the sub picture will be 4:3.
• In PBP mode, the aspect ratio of the sub
picture is fixed as 16:9 regardless of the
Aspect setting.
Size = 0
Size = 1
Size = 2
Size = 3
Size = 4
Size = 5
Size = 6
Size = 7
Size = 8
Size = 9
Size = 10
Size = 11
Size = 12
Size = 13
Size = 14
Aspect Ratio = 16:9
(fixed)
Width
Height
747
267
542
305
612
344
680
382
748
421
816
459
886
498
954
537
1022
575
1092
614
1160
652
1228
691
1296
729
1366
768
1434
807
Unit: pixel
42
The OSD (On-Screen Display) menu
PAP Setting
(continued)
• Picture Position: (PIP only) Changes the position of the sub picture.
Upper Left
Upper Right
Lower Left
Lower Right
• PAP is not available for all signal source combinations. See "Supported PAP input signal
combination" on page 77 for more information on supported combinations.
• In PAP mode, only sound from the active picture will be available.
Display Wall
Aspect
• H. Monitors/V. Monitors: Sets the number of displays used in the
horizontal/vertical direction.
• H. Position/V. Position: Sets the horizontal/vertical position of the
display wall matrix.
• Frame Comp.: Adjusts images near the display edges for optimal
demonstration across the display wall.
• LED: Turns the power indicator on the display on or off.
• Power On Delay: Choose to enable or disable a sequence in turning
on the screen matrix. If enabled, the display will turn on with a maximum
of 10-second delay.
Sets the picture’s aspect ratio.
• Wide Zoom: Enlarges to fill screen with minimum distortion.
• Zoom: Enlarges the picture, keeping the same aspect ratio.
• Full: Enlarges the picture horizontally to fill the screen when the picture
source is 4:3 (Standard definition). When the picture source is 16:9 (High
definition), it displays in the same 16:9 aspect ratio.
• 4:3: Displays all picture source in 4:3 aspect ratio.
• Full 1: Enlarges the picture to fill the screen in the vertical direction,
keeping the same aspect ratio. A black frame may appear around the
picture.
• Full 2: Enlarges the picture to fill the screen.
• Real: Displays the picture in its original number of dots.
The OSD (On-Screen Display) menu
Aspect
(continued)
Adjust Screen
For video signal inputs
4:3 original source
16:9 Original source
Wide Zoom
Wide Zoom
Zoom
Zoom
Full
Full
4:3
4:3
For PC signal input
Real
Full 1
Full 2
• Auto Adjustment: Sets whether to optimize image display for each
VGA input.
• Phase: Adjusts the phase of the VGA input image.
• Clock Frequency: Adjusts the clock frequency of the VGA input
image.
• H. Position: Adjusts the horizontal position of the VGA input image.
• V. Position: Adjusts the vertical position of the VGA input image.
43
44
The OSD (On-Screen Display) menu
Freeze
Select On to freeze the displayed image. To resume normal image display,
select Off.
You can also press FREEZE on the remote control to freeze or unfreeze the
image.
Touch Feature
When turned on, Aspect, PIP, Overscan and Display Wall will be
disabled to optimize touch performance.
This feature is only available for VGA, DVI and HDMI inputs.
The OSD (On-Screen Display) menu
45
Setting menu
Setting
Language
Schedule
Power Save
Control Setting
Network Settings
Set Monitor ID
HDMI Control
Advanced
Information
All Reset
:Move
Name
Language
Schedule
ENTER :Enter
English
High
RS-232C
1
Off
EXIT :Exit
Description
Sets your preferred language for the OSD menu.
• Date and Time: Sets the current date and time.
• Clock Display: Sets whether to show the current time which was set.
• Input: Sets an input source to display when the display is automatically turned
on next time.
• On/Off Timer: Sets when to turn on or off the display.
• Set the current time before you set the On/Off Timer.
• When schedule settings overlap, the Every day setting takes priority over other weekly
settings.
Power
Save
Sets the display to enter the power saving mode when there is no signal
detected.
• Low: All source can enter the power saving mode and wake up the display.
• High: All source can enter the power saving mode, but only a VGA signal can
wake up the display or you have to press the power button to wake up the
display when other source is connected.
• Off: If no source is detected, the backlight will continue on.
• RS-232C can bring any mode out of the power saving status.
• On Power Save setting High, the LAN function is not available if the monitor enters
Power Save, or DC off mode.
46
The OSD (On-Screen Display) menu
Control
Setting
• RS-232C/LAN: Sets a terminal to control the display.
• IR Passthrough: Select it when multiple displays are connected via RS-232C
cables.
- Primary: Designate the display as the primary unit for remote control
operation. Only this display will be operated by the remote control.
- Secondary: Designate the display as the secondary unit. The display can
not be operated by the remote control, and will only receive the control
signal from the primary display via the RS-232 connection.
To go back to the default setting (RS-232C) for Control Setting, press INFO on the
remote control for 5 seconds.
Network
See "Network connection" on page 35 for details.
Settings
Set Monitor Assigns an ID number for the current display when multiple displays are
ID
connected.
For use when under the RS-232C control mode.
HDMI
Control
Advanced
Uses the HDMI CEC (Consumer Electronics Control) industry standard
protocol to share functionality between connected devices and the display. To
transfer system commands, you need to use an HDMI cable to connect the
display to a device equipped with HDMI CEC. Select On in this menu and you
can operate the main functionalities on your display and the connected device
with one remote control.
• Auto Search: If turned On, the display automatically detects available input
sources..
• Auto Adjustment: Automatically optimizes image display for the VGA
input.
• Overscan: Turns the overscan function on or off.
• RGB Signal: Sets the type of signal for a piece of video equipment or PC
connected to the HDMI of the display
• Anti Image Retention: Automatically displays swift moving patterns to
prevent image retention on the screen.
• OSD Rotation: Adjusts the OSD rotation.
See product specifications for models recommended for portrait orientation. Landscape
only models operated in portrait mode may result in premature failure and will not be
covered under the warranty.
• OSD Info Box: When turned On, switching signal inputs, or changing timing,
the display will show the current input source and resolution onscreen. Select
Off to show the information box onscreen only when you press INFO on the
remote control.
• Adaptive Contrast: Turns the Adaptive Contrast function on or off. This
feature enhances image contrast for dark scenes.
This feature is not available if the Ambient Light Sensor function is set to On.
• Ambient Light Sensor: When turned On, the image brightness will adjust
automatically as the ambient lighting conditions change.
The OSD (On-Screen Display) menu
Information Displays the following information of your display.
• Date
• Model Name
• Serial Number
• Operating Time
• Software Version
• LAN Version
• IP Address
All Reset
Returns all settings to factory default values.
47
48
Multimedia OSD operation
Multimedia OSD operation
The multimedia OSD system provides a variety of settings when the display is connecting
to USB devices, wireless networks, or using the built-in storage device, etc.
To access the multimedia OSD system:
1. Make sure the display is correctly connecting to a multimedia device. See "Connecting the multimedia inputs (SL series only)" on page 24 for details.
2. Press MULTI-MEDIA on the remote control or select MULTI-MEDIA from the
source selection bar to access the multimedia OSD system. The main page appears.
3. Select your desired menu to operate.
Multimedia buttons on the remote control
To operate the multimedia OSD system, use the buttons on the remote control.
No
Name
Description
1
HOME
Goes back to the main page.
2
ESC
Goes back to the previous page.
3
ENTER
Activates the selected menu item.
Directional arrows for selecting a desired item.
4
(PREV)
5
REV
(NEXT)
Rewinds the video/audio clips.
Multimedia OSD operation
6
Plays/Pauses the video/audio clips.
7
Stops the video/audio clips.
8
49
Fast forwards the video/audio clips.
FWD
Viewing files
• Files on the built-in storage device
The display is built-in an approximate 3GB storage device. To transfer files to the display,
you need to take a USB cable, connect the type A plug to your computer and connect
the mini B plug to the display. Once connected, locate the Removable Disk on your
computer. Select and drag the target files from your computer to the Removable Disk.
Make sure the files are completely transferred to the display.
Go to the EZ Media > Internal Memory menu to view the files.
• Files on your USB flash drive
To view the files on your USB flash drive, simply plug your USB flash drive to the USB A
jack on the display. Go to the EZ Media > USB menu to view the files.
You can view various types of files in EZ Media > Internal Memory or EZ Media >
USB menu.
• Photo: Lists all the supported files in thumbnail view. Select the picture you want to
display and perform the functions as provided on the screen according to your needs.
Remote control key function in thumbnail view
No
Name
Description
1
HOME
Goes back to the main page.
2
ESC
Goes back to the previous page.
3
ENTER
Opens the selected photo.
Directional arrows for selecting a desired photo.
4
(PREV)
5
REV
(NEXT)
N/A
50
Multimedia OSD operation
6
N/A
7
N/A
8
N/A
FWD
Remote control key function in browse mode
No
1
Icon
Description
Rotation
Press / /ENTER to rotate the picture clockwise (0 >
90 > 180 > 270).
2
Press / to rotate the picture counterclockwise (0 >
270 > 180 > 90 > 0).
Zoom
Press ENTER to zoom in/out on the picture.
3
Press (PREV)
Previous photo
4
Next photo
(NEXT)
to navigate the picture.
6
Slideshow mode
Press ESC/ENTER/ (PREV)
browse mode.
Deletion
7
Press ENTER and then
Duplication
5
8
9
(NE
/
to go back to the
to delete the picture.
Press ENTER and then / to copy the picture.
Information
Shows the current information of the picture.
Returns to the previous page.
Multimedia OSD operation
• Video: Lists all supported files. Select the video you want to display and perform the
functions as provided on the screen according to your needs.
Remote control key function in list view
No
Name
Description
1
HOME
Goes back to the main page.
2
ESC
Goes back to the previous page.
3
ENTER
Opens the selected video.
/
4
(PREV)
5
REV
(NEXT)
: Sorts items by file names (alphabetically) or created
time.
: Shows subtitle files for the selected item.
N/A
6
N/A
7
N/A
8
FWD
: Moves up/down to select an item.
N/A
51
52
Multimedia OSD operation
Control user interface
Remote control key function: when the control user interface is displayed
No
Name
Description
1
HOME
Goes back to the main page.
2
ESC
3
ENTER
When the video is playing, hides the control user
interface.
When the video is not playing, goes back to the previous
page.
Plays/Pauses the video.
4
(PREV)
5
(NEXT)
/
: N/A
: Plays the previous video.
: Plays the next video.
Rewinds the video. Rate: x1, 2, 4, 8
REV
6
Plays/Pauses the video.
7
Stops the video.
8
Fast forwards the video. Rate: x1, 2, 4, 8
FWD
Remote control key function: when the control user interface is not displayed
No
Name
Description
1
HOME
Goes back to the main page.
2
ESC
Goes back to the previous page.
3
ENTER
Shows the control user interface.
Multimedia OSD operation
4
(PREV)
5
(NEXT)
/
: N/A
: Plays the previous video.
: Plays the next video.
Shows the control user interface.
REV
6
Shows the control user interface.
7
Shows the control user interface.
8
Shows the control user interface.
FWD
• Audio: Lists all supported files. Select the audio you want to play and perform the
functions as provided on the screen according to your needs.
Remote control key function in list view
No
Name
Description
1
HOME
Goes back to the main page.
2
ESC
Goes back to the previous page.
3
ENTER
Opens the selected audio.
53
54
Multimedia OSD operation
4
(PREV)
(NEXT)
/
: Moves up/down to select an item.
: Sorts items by file names (alphabetically) or created
time.
5
: N/A
N/A
REV
6
N/A
7
N/A
8
N/A
FWD
Remote control key function when playback
No
Name
Description
1
HOME
Goes back to the main page.
2
ESC
Goes back to the previous page.
3
ENTER
Plays/Pauses the audio.
4
(PREV)
(NEXT)
/
: N/A
: Plays the previous audio.
5
REV
: Plays the next audio.
Rewinds the audio.
6
Plays/Pauses the audio.
7
Stops the audio.
8
FWD
Fast forwards the audio.
Multimedia OSD operation
55
• Office Viewer: Supports PowerPoint/Word/Excel/PDF files. Select the document you
want to display and perform the functions as provided on the screen according to your
needs.
Remote control key function in list view
No
Name
Description
1
HOME
Goes back to the main page.
2
ESC
Goes back to the previous page.
3
ENTER
Opens the selected file.
4
(PREV)
(NEXT
/
: Moves up/down to select an item.
: Sorts items by file names (alphabetically) or created
time.
5
REV
: N/A
N/A
6
N/A
7
N/A
8
FWD
N/A
56
Multimedia OSD operation
Remote control key function when a document is opened
No
Name
Description
1
HOME
Goes back to the main page.
2
ESC
Closes the document.
3
ENTER
Zooms in to the maximum view or zooms out to the
minimum view.
4
(PREV)
(NEXT)
: Moves to the top of the page or goes back to the
previous page.
: Moves to the bottom of the page or goes to the next
page.
5
/ : Moves to the left/right of the page.
Goes back to the previous page.
REV
6
N/A
7
N/A
8
Goes to the next page.
FWD
Making connections
Except for those conventional cables, e.g. VGA cable, DVI cable, you can connect to the
display with more flexible ways.
• Using a USB cable (EZ USB)
1. Take a USB cable and connect the mini B plug to the display, type A plug to a PC.
2. Have your computer ready with the EZ USB software installed. To obtain the EZ
USB software, please go to local website from www.BenQ.com.
Supported OS for EZ USB:
• Windows XP 32/64 bit SP3 (Professional or higher)
• Windows Vista 32/64 bit SP2 (Home premium or higher)
• Windows 7 32/64 bit SP1 (Home premium or higher)
• Mac OSD 10.7 or higher
Multimedia OSD operation
57
3. Go to the EZ Display > EZ USB menu and confirm your selection.
4. Use the EZ USB software to set how you will use the display. You can send your
computer screen directly to the display by selecting Mirror mode, or treat the
display as an extended desktop by selecting Extension mode. For details about how
to install and use the software, see its user manual.
• Using WiFi (EZ WiFi)
1. Plug a wireless dongle to the USB A jack on the display.
2. Have your computer ready with the EZ WiFi/LAN software installed, or iOS/
Android device ready with the EZ Display app installed. To obtain the software,
please go to local website from www.BenQ.com.
The EZ Display is also available on Google Play (Android) or App Store (iOS).
3. Depending on your need and the availability of the equipment, select a connection
method (AP Mode/Client Mode) in the Settings > WiFi menu.
- AP Mode: Make sure your device has a built-in wireless network adapter and it is
enabled. Obtain or change the display’s SSID and related information in the
Settings > WiFi > AP Mode. Search for and select the display by clicking the
wireless icon to view the Wireless Networks window on your device.
- Client Mode: In this mode, you need to have a wireless enabled computer. Select
an available wireless network from the list of Settings > WiFi > Client Mode.
Connect to the same wireless network by clicking the wireless icon to view the
Wireless Networks window on your device.
58
Multimedia OSD operation
4. Go to the EZ Display > EZ WiFi menu and confirm your selection. The password
of the display appears on the screen.
5. Open the EZ WiFi/LAN software or EZ Display app, and enter the password for the
display. Use the software to set how you will use the display. You can allow multiple
computers to connect to the display, and manage those computers by selecting a
split screen, send your computer screen directly to the display by selecting Mirror
mode, or treat the display as an extended desktop by selecting Extension mode. For
details about how to install and use the software, see its user manual.
(EZ WiFi/LAN)
When a display is searched, enter the password shown in the EZ Display > EZ
WiFi menu.)
(EZ WiFi/LAN)
When multiple displays are searched, enter the password for the display you want
to connect with.)
Multimedia OSD operation
59
(EZ Display)
1. Connect to a display.
4. You can also click
“More” to discover more
functions provided.
2. Enter the password
for the selected display.
5. In this example picture,
“Quad Split” is selected,
and only one computer is
allowed to be displayed.
Click “Select Layout”.
3. Select the function icon
on the bottom to display
your file.
6. More options are
available.
7. Select one layout and
click “Finish”.
• Using a RJ-45 cable (EZ LAN)
You have to select LAN in the Setting > Control Setting menu for the display OSD
before using this EZ LAN connection.
1. Take a RJ-45 cable and connect it to your computer, and Ethernet or router.
60
Multimedia OSD operation
2. Take another RJ-45 cable and connect it to the display, and your Ethernet or router.
Make sure that your computer and the display is on the same local area network
(LAN).
You can also use your Android/iOS device to connect to the display if the network
equipment is wireless enabled.
3. Have your computer ready with the EZ WiFi/LAN software installed. To obtain the
EZ WiFi/LAN software, please go to local website from www.BenQ.com.
4. Depending on your need and the availability of the equipment, select a connection
method (Auto/Manual) in the Settings > LAN menu.
- Auto: Select it when you are in a DHCP environment.
- Manual: Fill in the required information when you are not in a DHCP
environment.
5. Go to the EZ Display > EZ LAN menu and confirm your selection. The password
of the display appears on the screen.
6. Open the EZ WiFi/LAN software and enter the password for the display. Use the
software to set how you will use the display. You can allow multiple computers to
connect to the display, and manage those computers by selecting a split screen, send
your computer screen directly to the display by selecting Mirror mode, or treat the
display as an extended desktop by selecting Extension mode. For details about how
to install and use the software, see its user manual.
Menu system
EZ Media
Select the device where the files you want to present are stored, and select the file type.
Name
Internal
Memory
USB
Description
See "Viewing files" on page 49 for details.
Supported file formats
• Photo: JPEG, BMP
Multimedia OSD operation
61
• Audio: MP1/MP2/MP3, WMA, OGG, ADPCM-WAV, PCM-WAV, AAC, MPEG Layer-3
(.mp3), IMA-ADPCM (.wav)
• Video: avi, divx, mkv, ts, dat, vob, mpg, mpeg, mov, mp4, rm, mvb, wmv
• Subtitle: Standard SRT (UTF-8/UTF-16)
Do not support mixed code in subtitle files.
• Office Viewer:
- Adobe PDF: accepts file size up to 75MB
PDF 1.0/1.1/1.2/1.3/1.4
- MS Word: accepts file size up to 100MB
British Word 95/Word 97/2000/2003/2007 (.docx)/2010 (.docx)
- MS Excel: accepts file size up to 15MB
British Excel 5, 95, Excel 97/2000/2002/2003/2007 (.xlsx)/2010 (.xlsx), Office XP
Excel
- MS PowerPoint: accepts document page number up to 1000, and file size up to
19MB
British PowerPoint 97, PowerPoint 2000/2002/2003/2007 (.pptx)/2010 (.pptx),
Office X PowerPoint, PowerPoint presentation-2003 and earlier (.ppx), PowerPoint
Presentation-2007 and 2010 (.ppsx)
• Storage:
- Internal Memory
TLC/MLC/SLC 8/12/24/40/60 bit ECC NAND
- USB
USB Flash, USB-HardDisk
EZ Display
Use an appropriate cable to make connection between your device and the display.
Name
EZ USB
EZ WiFi
Description
Connects to a computer by using a USB cable. See "Making
connections" on page 56 for details.
Connects to a computer via wireless enabled equipment. See
"Making connections" on page 56 for details.
62
Multimedia OSD operation
EZ LAN
Connects to a computer via RJ-45 cables. See "Making connections"
on page 56 for details.
Settings
Name
System
Video
Photo
Audio
WiFi
Description
• Version: Displays the version number of the firmware.
• Language: Sets your preferred language for the OSD menu.
• Update: Updates the OSD firmware with a USB flash drive.
• Hostname: Displays the display’s name for network identification.
• USBConnect: When a USB cable is connected between the
display and computer. Enable this function and a Removable Disk
icon will appear for files transfer.
• Auto Play Mode: Enables automatically playback the content
from the USB flash driver once it is connected to the display. You
can select to playback a certain type of file from among:
- Photo
- Video
- Audio
• Display Ratio: Sets the video clip’s aspect ratio.
• Repeat Mode: Sets the video clips’ playback mode.
• Display Ratio: Sets the picture’s aspect ratio.
• Slideshow Duration: Sets the interval time of each slide.
• Repeat Mode: Sets the video clips’ playback mode.
• AP Mode: Fills in the information required for WiFi connection.
- SSID: Sets a name for your display.
- Security: Selects a security level.
- PSK: Sets an access password.
- Channel: Selects a channel to communicate.
• Client Mode: Lists all wireless networks detected in your area
and selects a suitable one.
Multimedia OSD operation
LAN
• Auto: Obtains an IP address when you are in a DHCP
environment.
• Manual: Sets the information required for LAN connection.
Contact your network administrator for those information.
• OFF: Turns off LAN connection.
63
64
Product information
Product information
Specifications
Item
Specifications
SL420
SL460
Backlight
D-LED
E-LED
Panel size
42"
46"
0.4833 x 0.4833
0.17675 x 0.53025
Pixel pitch (mm)
Native resolution
(pixels)
LCD panel
Brightness (cd/m2)
(typical)
500
1000:1
4000:1
Adaptive Contrast
10,000
40,000
9
6.5
8 bit
10 bit (8 bit + FRC),
1073.7 M
Panel Bit
Computer
VGA (D-Sub 15-pin)
Video
DVI (DVI-D), Composite Video (BNC jack), SVideo, YPbPr (RCA jacks), HDMI, DisplayPort
Audio
L/R (RCA jacks), Line-in (3.5 mm jack)
USB
Type A; Mini B
Control
Computer
Video
Output
400
Contrast (typical)
Response time (ms)
(typical)
Input
1920 x 1080
Speaker
RS-232C (D-Sub 9-pin),
RJ45 (Jack RJ45 W/LED I)
VGA (D-Sub 15-pin)
Composite Video (BNC jack)
External speaker jack (12W+12W, 8 Ohms)
Audio
Control
Audio
Audio W (Amp)
12W x 2
Internal speaker
12W x 2
Supply
Power
Consumption Max.
100 - 240V AC, 50/60 Hz
< 150W
< 150W
Consumption Standby
< 0.5 W
Operating Temperature
0 - 40oC, 32 - 104oF
Operating Humidity
Environment
L/R (RCA jacks)
RS-232C (D-Sub 9-pin)
Storage Temperature
Storage Humidity
Display Orientation
10 - 90% (without condensation)
-20 - 60oC, 4 - 140oF
10 - 95% (without condensation)
Landscape/Portrait
Product information
Weight (kg)
Mechanical
Dimensions
(W x H x D) (mm)
Bezel Dimension - T/B/
L/R (mm)
Feature
< 18
< 22
981 x 571 x 106
1052 x 606 x 84
22.5/22.5/22.5/22.5
14.9 x 14.9 x 14.9 x
14.9
VGA daisy chain
O
DVI daisy chain
X
RS232 control daisy
chain
O
ID setting
O
Sharpness
enhancement
O
Proof of image
retention
O
Dimming control
(Adaptive Contrast)
O
Picture in Picture (PIP)
O
Picture by Picture
(PBP)
O
10 Bit color processing
O
Built-in video wall
support
O
Scheduling
O
Total turn-on time
O
Diagnostic DC voltage
(12v/5v)
O
Internal temperature
Sensor
O
CEC control
O
65
66
Product information
Item
Specifications
Backlight
Panel size
Pixel pitch (mm)
IL420
IL460
D-LED
E-LED
42"
46"
0.4833 x 0.4833
0.17675 x 0.53025
Native resolution
(pixels)
LCD panel
Brightness (cd/m2)
(typical)
1920 x 1080
400
500
Contrast (typical)
1000:1
4000:1
Adaptive Contrast
10,000
40,000
9
6.5
8 bit
10 bit (8 bit + FRC),
1073.7 M
Response time (ms)
(typical)
Panel Bit
Technology
IR Touch 6 points
Resolution
Touch
32767 x 32767
Capacity
6 simultaneous touches
Accuracy
+/- 6mm over 95% of touchable area
Touch Output
OS
Glass
Tempered glass
Computer
Input
3 mm + 0 mm/-0.3 mm
VGA (D-Sub 15-pin)
Video
DVI (DVI-D), Composite Video (BNC jack), SVideo, YPbPr (RCA jacks), HDMI, DisplayPort
Audio
L/R (RCA jacks), Line-in (3.5 mm jack)
Control
Computer
Video
Output
USB 2.0
See "Supported operating systems" on page 32
Speaker
RS-232C (D-Sub 9-pin),
RJ45 (Jack RJ45 W/LED I)
VGA (D-Sub 15-pin)
Composite Video (BNC jack)
External speaker jack (12W+12W, 8 Ohms)
Audio
Control
Audio
RS-232C (D-Sub 9-pin)
Audio W (Amp)
12W x 2
Internal speaker
12W x 2
Supply
Power
L/R (RCA jacks)
Consumption Max.
Consumption Standby
100 - 240V AC, 50/60 Hz
< 150W
< 150W
< 0.5 W
Product information
0 - 40oC, 32 - 104oF
Operating Temperature
Operating Humidity
Environment
10 - 90% (without condensation)
-20 - 60oC, 4 - 140oF
Storage Temperature
Storage Humidity
10 - 95% (without condensation)
Display Orientation
Weight (kg)
Mechanical
Dimensions
(W x H x D) (mm)
Bezel Dimension - T/B/
L/R (mm)
Feature
67
Landscape/Portrait
< 23
< 28
981 x 571 x 121
1066 x 621 x 100
22.5/22.5/22.5/22.5
22.5 x 22.5 x 22 x 22
VGA daisy chain
O
DVI daisy chain
X
RS232 control daisy
chain
O
ID setting
O
Sharpness
enhancement
O
Proof of image
retention
O
Dimming control
(Adaptive Contrast)
O
Picture in Picture (PIP)
O
Picture by Picture
(PBP)
O
10 Bit color processing
O
Built-in video wall
support
O
Scheduling
O
Total turn-on time
O
Diagnostic DC voltage
(12v/5v)
O
Internal temperature
Sensor
O
CEC control
O
68
Product information
Item
Specifications
IL650
Backlight
Panel size
LCD panel
E-LED
65"
Pixel pitch (mm)
0.744
Native resolution
(pixels)
1920 x 1080
Brightness (cd/m2)
(typical)
Contrast (typical)
360
4000:1
Adaptive Contrast
Response time (ms)
(typical)
Panel Bit
Touch
IR Touch 2 points
Resolution
32767 x 32767
Capacity
2 simultaneous touches
Accuracy
<1.5 mm (central area)
<2.5 mm (marginal area)
OS
Tempered glass
Computer
Audio
L/R (RCA jacks), Line-in (3.5 mm jack)
Computer
Video
Speaker
Audio
Control
RS-232C (D-Sub 9-pin),
RJ45 (Jack RJ45 W/LED I)
VGA (D-Sub 15-pin)
Composite Video (BNC jack)
X
L/R (RCA jacks)
RS-232C (D-Sub 9-pin)
Audio W (Amp)
12W x 2
Internal speaker
12W x 2
Supply
Power
O
VGA (D-Sub 15-pin)
DVI (DVI-D), Composite Video (BNC
jack), S-Video, YPbPr (RCA jacks),
HDMI, DisplayPort
Control
Audio
USB 2.0
See "Supported operating systems" on
page 32
Video
Input
Output
10 bit
Technology
Touch Output
Glass
8
100 - 240V AC, 50/60 Hz
Consumption Max.
265 W
Consumption Standby
< 0.5 W
Product information
Operating Temperature
Operating Humidity
Environment
Storage Temperature
Storage Humidity
Display Orientation
0 - 40oC, 32 - 104oF
10 - 90% (without condensation)
-20 - 60oC, 4 - 140oF
10 - 95% (without condensation)
Landscape/Portrait
Weight (kg)
Mechanical
Dimensions
(W x H x D) (mm)
Bezel Dimension - T/B/
L/R (mm)
Feature
1520.4 x 882 x 107.1
36.9 / 36.9 / 43.9 / 43.9
VGA daisy chain
O
DVI daisy chain
X
RS232 control daisy
chain
O
ID setting
O
Sharpness
enhancement
O
Proof of image
retention
O
Dimming control
(Adaptive Contrast)
O
Picture in Picture (PIP)
O
Picture by Picture
(PBP)
O
10 Bit color processing
O
Build-in video wall
support
O
Scheduling
O
Total turn-on time
O
Diagnostic DC voltage
(12v/5v)
O
Internal temperature
Sensor
O
CEC control
O
Specifications and functions are subject to change without notice.
69
70
Product information
Dimensions
• SL420
51.1
105.1
186.4
200
183.8
294.2
400
286.4
22.5
22.5
22.5
980.6
935.6
22.5
525.2
570.2
Unit: mm
Product information
71
• SL460
30
200
84
203.84
201.83
325.54
400
325.54
14.9
14.9
14.9
2162/19
2132/39
14.9
575.87
605.67
Unit: mm
72
Product information
• IL420
33/6
980.6
935.6
927.9
22.5
522
22.5
22.5
525.2
570.2
200
121.1
67.1
186.39
183.81
294.22
400
286.38
Unit: mm
Product information
73
• IL460
32/::
2176/37
2132/39
2129/19
33/5
686/98
731/77
32/::
683/78
33/5
211
57
443/74
511
443/74
322/44
311
31:/45
Unit: mm
74
Product information
• IL650
882
820.54
37.18
569.8
1520.4
1446.04
30.73
107.1
53.1
560.2
400
560.2
75
100
251.5
75
100
451.3
241
400
241
Unit: mm
Product information
75
Supported input signal resolution
Input source
Resolution
640 x 480 @ 60Hz
640 x 480 @ 72Hz
640 x 480 @ 75Hz
720 x 400 @ 70Hz
800 x 600 @ 60Hz
800 x 600 @ 75Hz
1024 x 768 @ 60Hz
1024 x 768 @ 75Hz
1280 x 768 @ 60Hz
1280 x 800 @ 60Hz
RB
1280 x 800 @ 60Hz
1280 x 960 @ 60Hz
1280 x 1024 @ 60Hz
1360 x 768 @ 60Hz
1366 x 768 @ 60Hz
1400 x 1050 @ 60Hz
1600 x 1200 @ 60Hz
1680 x 1050 @ 60Hz
RB
1600 x 1050 @ 60Hz
1920 x 1080 @ 60Hz
NTSC-M
NTSC-J
PAL-BDGHI
576i (50Hz)
480i (60Hz)
480p (60Hz)
576p (50Hz)
720p (50Hz)
AV
S-Video
YPbPr
VGA
HDMI
DVI
Display
Port
76
Product information
720p (60Hz)
1080i (50Hz)
1080i (60Hz)
1080p (50Hz)
1080p (60Hz)
•
: supported
• Blank: not supported
Product information
77
Supported PAP input signal combination
Main/Left picture signal source
AV
AV
S-Video
Sub/
Right
pictur
e
signal
sourc
e
YPbPr
VGA
DVI
HDMI
Display
Port
Multimedia
SVideo
YPbPr
VGA
DVI
HDMI
Displa
yPort
Multimedia
78
Troubleshooting
Troubleshooting
Problem
No picture
No sound
The computer input
image looks strange
The control panel
buttons do not work
Solution
Check the following:
• Is the display turned on? Check the power indicator of the
display.
• Is the signal source device turned on? Turn on the device
and try again.
• Are there any loose cable connections? Make sure that all
cables are connected firmly.
• Have you chosen an unsupported output resolution on
the computer? Refer to "Supported input signal
resolution" on page 75 to select a supported resolution
and try again.
• Have you chosen an unsupported output resolution on
the DVD or Blu-ray disc player? Refer to "Supported input
signal resolution" on page 75 to select a supported
resolution and try again.
Check the following:
• Have you turned on the mute function on the display or
the input source device? Turn off the mute function or
increase the audio volume level and try again.
• Are there any loose cable connections? Make sure that all
cables are connected firmly.
• Have you chosen an unsupported output resolution on
the computer? Refer to "Supported input signal
resolution" on page 75 to select a supported resolution
and try again.
• Use the Auto Adjustment function ("Adjust Screen" on
page 43) to let the display automatically optimize the
display of computer image.
• If the result of the Auto Adjustment function is not
satisfactory, use the Clock Frequency, Phase, H.
Position and V. Position functions to manually adjust
the image.
Have you locked the control panel buttons? Unlock the
buttons and try again.
Troubleshooting
The remote control does • Have you locked the remote control function? Unlock the
not work
function and try again.
• Check for incorrect battery orientation.
• Check for dead batteries.
• Check your distance and angle from the display.
• Check whether remote control is properly being pointed
at the display’s remote control sensor window.
• Check for any obstacle between the remote control and
the remote control sensor window.
• Check that the remote control sensor window is not
under strong fluorescent lighting, or in direct sunlight.
• Check for any devices (computer or personal digital
assistant, PDA) nearby that transmit infrared signals which
may cause interference to signal transmission between the
remote control and the display. Turn off the infrared
function of these devices.
4/28/14
79