Download PDF Install Guide for 16 Stage Throttle Remapper

E-Drive Advance
Instruction Manual
Setup
The component of E.T.C description
 Display
Display current mode
 Setup
Buttons
Acceleration and fuel consumption of each step
Display current level
Mode switch button
Level down adjusting button
High
Acceleration
rate
Fuel
consumption
Please be sure to set first after installation. No need to set anymore after completion.
Starting Anti-skid function setup
To learn the correct throttle signal.
A.Turn on the starting Anti-skid mode
No use if the product without learning setting.
Initial setup instruction
Press
Press
The preparation before learning setting.
1. Must double check all the wire and fitting is connected well.
2. Turn the switch on, shift the gear to “P” or “N” position while the engine is off.
Code (shown on monitor)
1
MODE
press
Release the “Mode” button
to start the mode shift.
MODE
Release
3
Do not step on pedal so the
E-drive can learn the
throttle opening percentage
is 0%
Display 0
Only under nor
mode, the setting is
possible.
4
Press any functional
MODE button,
Press
or
can do
100 %
6
The figure starts
to count back
from 7,6,5…1,0
after displaying （ex）
Letter ”L” light is blinking
The last battery
indicating light is blinking
MODE
Letter “H” light is word
blinking
All battery indicating light
are all blinking
Press
7
When the battery indicating light
shows full, the setup is
completed. Please release the
accelerator
5
A.Anti-theft function setup
Press
MODE
MODE
MODE
Battery indicating
lights are full.
1.Under ECO mode, long
press Mode button and wait
for 2 seconds
MODE
8
Setting completed!
Please be sure to reset when installing in other cars.
Please re-run the initial setup if the code shown on
monitor.
※
Press
MODE
press
“Nor” remained
If there is
blinking and then automatically back to ” 1 ”.
Please set the throttle opening percentage correctly.
2
1.Under Power mode,
long press Mode button
and wait for 2 seconds
Press
Press any button can
immediately stop the
launch contrl mode
Troubleshooting
Please verify if any event occurs as below when the E-drive doesn’t work.
Display 0
Only under nor
mode, the setting
is possible.
Symptom
1.Hold the Mode button. While it is counting down, hold “up”
and “down” buttons at the same time. Wait for 2 seconds till
the monitor shows “-“, and it means resetting to zero success.
2.At this time, pressing Mode button won’t switch between
each mode, and the monitor will show “0” with blinking.
No reaction when
battery switch is
on.
Engine check light
is on
Press “Mode” button to shift the mode.
2
3
1
4
MODE press
Press Mode
button, the display
shows “0” with
blinking, and stays
in Nor mode.
Ec
nor
SP
Economic fuel
consumption mode
Normal mode
Power mode
※Each press of MODE button will switch in the order of 1 2 3 4
Step shift
The step shifted under “Ec”
and “Po” mode.
2.When “Po” light and
“number” light blink at the
same time, it is under
launch control mode
Warning: Under launch mode, the accelerator response is very quickly.
Please be careful on handling the car. NO switching to(R) backward
gear under this mode
MODE
Mode shift
B.Turn off the launch
control mode
MODE
flashing
MODE
Avoid the engine light on while installing in other vehicle.
Turn the battery switch
on.
(The engine must ON
be off)
When the engine is
starting, press anti-theft
button and wait for 2
seconds until shows the
previous mode. And the
anti-theft mode turns off
Launch control function setup
MODE
（ex）
2.Wait till the lights on the
panel all turn off, and then it
is entering the anti-theft
mode. Under this mode,
starting engine or pressing
the accelerator will have no
response. The vehicle is
completely shut down.
Press
When press the “Mode” button to
run the mode or step shift.
MODE
1
B.Turn off anti-theft
function
MODE
A.Turn on launch control mode
Please reset the machine when installing in other vehicle.
Reset
Press any button will turn
off the Anti-skid mode
immediately
Start anti-theft function
when releasing the
accelerator,
battery indicating light will
fall back to disappear
※
Letter “H” light is word
blinking
All battery indicating light
are all blinking
2.When the functioning light
at the upper right corner
lights up, and the number
light turns off, it is entering
the Anti-skid mode.
Press
MODE
Press
B.Turn off the starting
Anti-skid mode
MODE
MODE
（ex）
MODE
MODE
1.Under any mode or level,
press UP and Down at the
same time.
※
（ex）
※
MODE
MODE
Press
Code (shown on monitor)
Press any functional MODE
button,
or
button can do
when accelerating
Letter ”L” light is blinking
The last battery
indicating light is blinking
0%
Step
Fully stepping on the pedal so
the E-drive can learn the throttle
opening percentage is 100%.
Hold “Mode” button till
the code becomes “0”
2
much
For your safety, the throttle runs with SPROTS mode is very sensitive, please notice the way to
step on pedal if driver changed or driving in reverse.
Learning mode setting (Throttle opening setup)
Step
low
less
Product shut-down time
The monitor will be lighted off after engine turned off 10 seconds to 5 minutes because its
power supply is synchronous with ECU.
If any throttle opening percentage shown on monitor is normal while the E-drive is shutting off.
Turn the battery switch
on.
(The engine must ON
be off)
ECO
9 8 7 6 5 4 3 2 1 ▼ 1 2 3 4 5 6 7
Throttle position
indicating light, the
longer the light, and
higher the percentage
of throttle
Level up adjusting button
NORMAL
POWER
MOD E
Starting anti-skid
engaging light
MODE
Cause
Trouble shooting
OBDII fitting is bad connected.
Fitting is bad connected when
taking cabling method 2.
Please check each fitting is
connected well.
Unplug the fitting of OBDII before
battery switch shut off completely.
Please turn engine off, wait for 30
seconds and re-start engine up.
No learning setting after
installation.
Please follow the learning set to
configure the opening of throttle,
then to eliminate engine light.
Incorrect learning setting.
Please reconfigure learning setting.
Please return all the accessory with body and harness for repair.
The throttle opening percentage of Po/Ec mode
Notes:
Reset engine check light
IF the engine check light is on because of incorrect installation and instruction, please try
the instruction as below:
1.Please turn off engine and wait for few minutes then start engine up, the light will be off.
2.If first solution is failed, please release the negative pole of battery and wait for 10 minutes
then connect the pole.
3.If both two methods are failed, please use the OBDII scanner (reader) to diagnosis.
MODE
Press
or
button,
and it will switch to the
next level.
-2-