Download User`s Manual

Transcript
PRO STAGE
PR-3051, 3052, 3053, 3054, 3055, 3056
This product manual contains important information about the safe installation and
use of this projector. Please read and follow these instructions carefully and keep
this manual in a safe place for future reference.
PR LIGHTING LTD.
Yingbin Road, Dashi Panyu, Guangzhou, 511430 China
http://www.pr-lighting.com
INDEX
TECHNICAL SPECIFICATIONS
SAFE USAGE OF THE PROJECTOR
INSTALLING THE PROJECTOR
FITTING THE LAMP
POWER CONNECTIONS
KEEPING THE PROJECTOR CLEAN
LIGHT OUTPUT
3
4
5
6
7
7
7
Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change
without notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the
course of product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any
consequence arising from them.
Every apparatus has been tested completely and packed properly by the manufacturer. Please make sure the packing and / or
the apparatus is in good condition before your installation and use. Should there be any damage caused by transportation,
consult your dealer and do not use the apparatus. But any damage caused by improper use will not be assumed by the
manufacturer and / or dealer.
ACCESSORIES
Safety cord (1 PCS)
This manual (1 PCS)
Colour-filter holder (1 PCS) (Only for 19°, 26°, 36°, 50° projectors)
Gobo with holder (1 PCS)
Optional: Iris device (1 PCS),
Colour-filter holder
Iris device
Gobo holder
Blade
INTRODUCTION
Thank you for purchasing our products Pro Stage, PR-3051, PR-3052, PR-3053, PR-3054, PR-3055,
PR-3056.
This product manual contains important information about the safe installation and use of this
projector. Please read and follow these instructions carefully and keep this manual in a safe place for
future reference.
The Pro Stage is an innovative projector with an elegant housing made from high quality aluminiunalloy with an insulating painting finish. The product complies to CE norms and standards.
The unit can be hung easily and safely. The angle of inclination for the projector-body is convenient to
be adjusted, and the lens-barrel can be changed easily. The unit uses high qualified reflector with
special reflective coating which can reduce the heat energe greatly, so the life of the elements in the
projector can be prolonged effectively. Using blades provided you can get various images and using
the filter holder provided you can get different colour effects. The lenses of 5°, 10°, 19°, 26°, 36°, 50°
2/10
Pro Stage manual.doc
have been installed in the different barrels, so you can change the barrels directly for your different
applications. The projector is suitable for use in stage, disco, night club or artistic applications.
5° Lens-Barrel
10° Lens-Barrel
19° Lens-Barrel
26° Lens-Barrel
36° Lens-Barrel
50° Lens-Barrel
PR-3051
PR-3052
PR-3053
PR-3054
PR-3055
PR-3056
TECHNICAL SPECIFICATIONS
Power supply: 230V AC 50Hz
Lamp: GKV 600W (Manufacturers Rated Lamp Life:250 hours)
Socket: G9.5
200
370
455
360
190
455
930
360
1000
5° Pro Stage, PR-3051, Net Weight: 7.3kg
200
370
430
310
190
455
310
720
780
10° Pro Stage, PR-3052, Net Weight: 6.8kg
3/10
Pro Stage manual.doc
200
370
250
190
455
250
545
610
19° Pro Stage, PR-3053, Net Weight: 7.2kg
26° Pro Stage, PR-3054, Net Weight: 7.2kg
36° Pro Stage, PR-3055, Net Weight: 7.2kg
50° Pro Stage, PR-3056, Net Weight: 7.2kg
SAFE USAGE OF THE PROJECTOR
When unpacking and before disposing of the package check there is no transportation damage before
using the projector. Should there be any damage caused by transportation, consult your dealer and
do not use the apparatus. Keep the package well for your possible future transportation.
The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain
and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other fluids,
or metallic objects.
The projector is not designed or intended to be mounted directly on to inflammable surfaces.
Hot housing surface! It can reach above 200℃! Do not touch the housing of the projector with your
hand during operation.
The projector is only intended for installation, operation and maintenance by qualified personnel.
The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent
surfaces.
Do not project the beam onto inflammable surfaces, minimum distance is 5m.
5m
Avoid direct exposure to the light from the lamp. The light is harmful to the eye.
Do not attempt to dismantle and / or modify the projector in any way.
Electrical connection must only be carried out by qualified personnel.
It is essential that each projector is correctly earthed and that electrical installation conforms to all
relevant standards.
4/10
Pro Stage manual.doc
Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the powercord come into contact with other cables. Only handle the power-cord by the plug. Never pull out the
plug by tugging the power-cord.
Keep the lamp and lens clean. Do not touch the lamp-glass and lens with bare hand.
Switching the lamp on and off at short intervals will reduce the life of both the lamp and the projector.
Occasional breaks will prolong the life of both the lamp and the projector.
Always replace the lamp if it becomes damaged or deformed.
Always replace the lens if it becomes cracked or badly scratched.
Never run the projector without a lamp and a lens in place.
Always disconnect from the mains, when the device is not in use or before
cleaning it or before attempting any maintenance work.
If you have any questions, don’t hesitate to consult your dealer or manufacturer.
INSTALLING THE PROJECTOR
Locking Knob for
Lens-Barrel Holder Rotating
Fixing Holes
Bracket
Hole for Safety Cable
Passing through
Blade or Gobo Holder
Lamp Housing Bolt
Retaining Block
for Filter Holder Lens-Barrel
Locking Knob
Lens-Barrel
Lens-Barrel
Holder
Cover
Locking Knob
Lamp Housing
Lamp Adjustment
Displacing the cover will appear the slot
for inserting the gobo with device
Cover Screw
This unit has been designed to be hung. Hang the unit via its bracket using M12 size bolt(s). When
you want to adjust the angle of the body of the projector, you only loosen the locking knob and then
adjust the angle of the body. You can change the lens-barrel by loosening 2 lens-barrel locking knobs
and rotate the lens-barre by loosening 2 lens-barrel holder rotating knobs. Always ensure that the
projector is firmly positioned to avoid vibration and slipping, and always ensure that the structure to
which you are attaching the projector is secure and is able to support the weight of each Pro Stage.
For safety the unit should have a secondary fixing with a safety cable through the hole on the upper of
the unit.
5/10
Pro Stage manual.doc
FITTING THE LAMP
Important: Before installation the GKV lamp verify that the GKV lamp you use is suitable for the
voltage at your facility. Operating lamps beyond their rated voltage reduces lamp life and can cause
premature lamp failure.
Lamp Housing
Lamp Housing Bolt
Lamp Adjustment
Lamp
First, loosen the lamp housing bolt and pull the housing straight out from the back of the fixture as
shown above.
Holding the lamp with the base push down on the lamp base until the lamp is firmly seated. Make sure
that the lamp is fully seated, with the bottom of the lamp heat sink flush to the lamp housing casting.
To reinstall the lamp housing, center it on the reflector and the bolt hole, then tighten the lamp
housing bolt to secure the lamp housing in place.
NOTE: To optimize light output it will be necessary to adjust the lamp adjustment. Adjust the lamp in
or out to get a proper focus via rotating the lamp adjustment by hand.
6/10
Pro Stage manual.doc
POWER CONNECTIONS
The unit is supplied with a power cord. Should any other connections be required they must be carried
out with the following configuration: Earth = Green/Yellow cord.
KEEPING THE PROJECTOR CLEAN
To ensure the reliability of the projector it should be kept clean. The lens and reflector should be
regularly cleaned to maintain an optimum light output.
Do NOT use any glass cleaner or any type of solvent on the reflector. Before cleaning the
reflector remove the lens barrel and the barrel holder so you can access the reflector from the front of
the fixture. When cleaning the reflector use a damp, clean, soft, lint-free cotton cloth with amild, soapy
water solution and gently wipe the reflector, and then remove any soapy water residue with a clean,
soft, lint-free cotton cloth dampened with water. Do not use paper towels or harsh materials to
wipe the reflector.
Cleaning frequency depends on the environment in which the fixture operates: damp, smoke or
particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics. It is
recommended to clean the lens at least once every 20 days and clean the reflector at least once
every 30 / 60 days.
Do not use any organic solvent, e.g. alcohol, to clean the housing of the
projector.
LIGHT OUTPUT
37183 lux 9295 lux 4130 lux 2323 lux 1487 lux
6m
4m
2m
0m
2m
5m
3m
1m
5°
1m
3m
4m
5m
6m
DISTANCE (m)
DIAMETER (m)
0
0
5
10
15
20
25
0.4
0.9
1.3
1.7
2.1
5° Pro Stage, PR-3051
7/10
Pro Stage manual.doc
22431 lux 5607 lux 2492 lux 1400 lux
6m
4m
2m
0m
2m
896 lux
5m
3m
1m
10°
1m
3m
4m
5m
6m
DISTANCE (m)
0
DIAMETER (m)
0
5
10
0.9
1.7
15
2.6
20
25
3.5
4.4
10° Pro Stage, PR-3052
4524 lux 1128 lux 500 lux
6m
4m
2m
0m
2m
282 lux 180 lux
5m
3m
1m
19°
1m
3m
4m
5m
6m
DISTANCE (m)
5
10
15
20
25
1.7
3.3
5.0
6.7
8.4
267 lux
168 lux
0
DIAMETER (m)
0
19° Pro Stage, PR-3053
4296 lux 1074 lux 476 lux
6m
4m
2m
0m
2m
5m
3m
1m
26°
1m
3m
4m
5m
6m
DISTANCE (m)
DIAMETER (m)
0
0
5
10
15
20
25
2.3
4.6
6.9
9.2
11.5
26° Pro Stage, PR-3054
8/10
Pro Stage manual.doc
2280 lux
10m
8m
570 lux
253 lux 140 lux
91 lux
9m
7m
6m
5m
4m
3m
2m
1m
0m
36°
1m
2m
3m
4m
5m
6m
7m
8m
9m
10m
DISTANCE (m)
DIAMETER (m)
5
0
3.24
0
10
15
20
25
6.49
9.74
13
16.2
36° Pro Stage, PR-3055
2035 lux 504 lux
14m
12m
10m
8m
6m
4m
2m
0m
2m
224 lux
127 lux
81 lux
13m
11m
9m
7m
5m
3m
1m
50°
1m
3m
4m
6m
8m
10m
12m
5m
7m
9m
11m
13m
14m
DISTANCE (m)
DIAMETER (m)
5
0
0
4.66
10
15
20
25
9.32
13.9
18.6
23.3
50° Pro Stage, PR-3056
9/10
Pro Stage manual.doc
PR LIGHTING LTD.
Add: Yingbin Road, Dashi, Panyu, Guangzhou, China
Post-Code:511430
TEL:(020)84781888
FAX:(020)84786023
P/N: 321010066
Last Revision: 13:05:2005
10/10
Pro Stage manual.doc