Download THINKSTATION C30

THINKSTATION C30
Product Overview
The dual-processor C30 workstation uses an Extended-ATX/EEB based motherboard, an 800 Watt (W) power supply unit
(PSU), and a 24-liter ATX form factor tower. The C30 motherboard consists of the Intel® C602 Chipset and two 2011pin Land Grid Array (LGA2011) Socket-R processor sockets, with support for quad core, six core, and eight core
processors from the Intel® Xeon line (Sandy Bridge EP). Memory support consists of error-correcting code (ECC)
unbuffered Double Data Rate 3 (DDR3) Synchronous Dynamic Random Access Memory (SDRAM). Maximum memory
supported is 128GB for UDIMMs and 256GB (pending 32GB RDIMM availability).
SECTION I: SYSTEM OVERVIEW
Operating Systems
Preloaded
Genuine Windows 7® Professional 64-bit
Genuine Windows 7® Professional 32-bit
Supported
Genuine Windows XP Professional 64-bit
Genuine Windows XP Professional 32-bit
Red Hat Enterprise Linux 6.2
Motherboard – C30
Table 1. C30 Motherboard Summary
C30 Motherboard Summary
Form Factor
Board Size
12.23″ x 14.01″ (310.68mm x
355.9mm)
Layout
Custom, based on Extended-ATX/EEB
Standard
Motherboard Core
Processor Support
Intel® Xeon™
EP)
Intel® Xeon™
EP)
Intel® Xeon™
EP)
Intel® Xeon™
EP)
Dual Core (Sandy Bridge
Quad Core (Sandy Bridge
Six Core (Sandy Bridge
Eight Core (Sandy Bridge
Socket Type
(2) x Intel Socket-R (LGA2011)
Memory Support
1600/1333/1066/800 MHz
QPI (GTPS)
6.4/7.2/8.0 GTPS Links
Voltage Regulator
VR12.1 – 130W TDP
Chipset (PCH)
Patsburg-A (Intel C602)
Support for Intel HW module to allow
enablement of Patsburg-B
Flash
128Mbit SPI Flash with FWH
HW Monitor
N/A
Super I/O
Nuvoton 6681D
Clock
ICS932SQ420B
Audio
Realtek ALC662-VD
Ethernet
Intel Lewisville(82579)
SAS
Integrated with Patsburg –A +
Enablement Module (Patsburg –B
equivalent)
Memory
Slots
4 per CPU socket
Channels
4 per CPU socket
Type
DDR3 Unbuffered SDRAM (UDIMM,
RDIMM, LRDIMM)
ECC Support
Yes
Speed
Up to PC3-12800 (1600MHz)
Max DIMM Size
Up to 8GB UDIMM, up to 32GB RDIMM
Max System Memory
UDIMM: up to 64GB (w/8GB modules)
RDIMM: up to 256GB RDIMM (w/32GB
modules)
Ethernet
Vendor
Intel
Count
1
EEPROM
None (part of SPI flash)
Speeds
10/100/1000 Mbps
Functions
PXE, WOL, AMT (82579), NC-SI
(82574), Jumbo Frames, Teaming
Connectors
(1) x RJ45 on Rear I/O
Audio
Vendor
Realtek
Type
HD (5.1)
Internal Speaker
Yes, using SSM2211 amplifier
Connectors
(3) x Rear 3.5mm Jacks (Line In, Line
Out, Microphone In)
(2) x Front 3.5mm Jacks (Headphone
out, Microphone In)
(1) x 2-Pin Internal Speaker Header
Video
Onboard
<Not Supported>
Adapter
(2) x PCI-E 3.0 16-Lane Slots
Additional adapters may be supported
in x4 slots for Spec Bids
Multi-GPU Support
BIOS supported, card dependent
Storage
Floppy
None
IDE
None
SATA/SAS
(2) x SATA Connectors, Gen. 2 (AHCI)
(2) x SATA Connectors, Gen. 3 (AHCI)
(3) x SATA/SAS Connectors, Gen. 2
(SCU)
(1) x eSATA Connector, Gen. 2 (eSATA
bracket)
• SATA RAID 0,1, 5 supported
natively
• SAS RAID 0,1 and SATA RAID 0,1
supported via SAS Enablement
Module
• SAS RAID 0,1,5 and SATA RAID
0,1,5 supported via LSI 9260-8i
adapter
SAS RAID 0,1 5 and SATA RAID 0,1, 5
supported via LSI 9240-8i adapter
(with RAID5 key)(
eSATA
Slots
Slot 1 (Near CPU)
Slot 2
Slot 3
Slot 4
Slot 5
Slot 6 (Near Edge)
Rear I/O
COM
eSATA
LPT
Video
Audio
Ethernet
USB 2.0
USB 3.0
Firewire
Internal I/O
USB 2.0
USB 3.0
PS/2
Audio
COM2
(1) x eSATA Connector, Gen. 2, cabled
to Slot via bracket
4-Lane PCI-E v3.0 (16-Lane
Mechanical) – Half Length, Full Height
16-Lane PCI-E v3.0 – Full Length, Full
Height
PCI v2.3 – Full Length, Full Height
16-Lane PCI-E v3.0 – Full Length, Full
Height
4-Lane PCI-E v2.0 Full Length, Full
Height, open tailgate (RF 2.5)
PCI v2.3 – Half Length, Full Height
(1) x Serial Port (COM1)
(1) x eSATA Port (Gen. 2), optional via
bracket
None
<No Onboard Video>
Microphone-In, Line In, Line Out
(1) x RJ45
(2) x USB 2.0 Ports
(2) x USB 3.0 Ports
None
•
x Front Panel USB Header (2
ports, Base MTM)
•
x Media Card Reader Header
•
x Internal USB connector
•
x Front Panel USB 3.0 edge
connector (2 ports, RF 2.5 MTM)
(1) x 2-port PS/2 Header (Rear)
(1) x Front Panel Mic & Line-Out
Header
None
Clear CMOS
Speaker
Chassis Intrusion
Firewire
Thermal
Fans
3-Pin Clear CMOS Header
2-Pin Internal Speaker Header
2-Pin Chassis Intrusion Switch Header
None
(1) x 4-Wire
(1) x 5-Wire
fans)
(1) x 4-Wire
(2) x 5-Wire
C30)
(1) x 3-Wire
installed)
Power Connectors
Main
Memory & CPU
Graphics
Security
TPM
CPU Fans
Rear Fans (1 header, two
Front Fan
Memory Fan (not used on
PCH Fan (PCH fan not
(1) 24-Pin (2×12) ATX Standard
(2) 8-Pin (2×4) ATX 12V Standard
(1) 4-Pin (2×2) ATX 12V Standard
Version 1.2, Nuvoton NPCT421LA0WX
(Base MTMs)
Version 1.2, ST Micro ST33TPM12LPC
(RF 2.5 MTMs and later)
NXP PCA24S08
vPro for WS (AMT 7.0)
Asset ID
vPro
BIOS
Vendor
AMI
Ethernet
The C30 motherboard implements an onboard gigabit Ethernet port via the Intel (82579) PHY. This integrated solution
has support for the industry standard functions of Wake on LAN (WOL) and Preboot Execution Environment (PXE),
Teaming, and Jumbo Frames. Additionally, for Manageability features, (82579) will support AMT 7.0.
Audio
The ALC662-VD chip from Realtek provides C30 with stereo audio capability that meets Windows7 Premium
performance requirements. There are 2 front analog jacks, and 3 rear color-coded analog jacks.
Clock Generator
The clock generator chip on C30 is an ICS932SQ420B. It is compliant with the Intel requirement for CK420 clock
generation, and had downstream support with a DB1900Z clock buffer.
Chassis Summary
Chassis Info
Chassis Format: Tower
Chassis Dimension – cm: 444mm D x 130mm W x 427mm H
Chassis Dimension – in: 17.48″ D x 5.12″ W x 16.81″ H
Chassis Weight = 40.7 lbs (18.5kg) maximum configuration
Chassis color: Raven Black
Power supply: 800W 90% Efficient
2P Thermal Solutions
The C30 2P system will utilize 4 fansink solutions. For the 2 rear CPU versions, one will support 80W/95W CPUs and
the other will support 130W CPUs. For the 2 front CPU versions, one will support 80W/95W CPUs and the other will
support 130W CPUs. Due to space requirements, the front CPU fansinks will be a different design point, and unique to
the C30.
In addition to the CPU fansinks, the C30 2P system will contain a 2 rear system fans which share the same connector, a
front PCI fan, a PCH fansink, and 2 optional memory chiller assemblies (2 fans each, 1 assembly per CPU).
Security & Serviceability
Physical Security and Serviceability
Access Panel
Tool-less side cover removal
Optical Drive
Tool-less
Hard Drives
Tool-less
Expansion Cards
Tool-less
Processor Socket
Tool-less
Color coded User
Touch Points
Yes
Color-coordinated
Cables and
Connectors
Yes
Memory
Tool-less
System Board
Tool-less
Green Color Power
LED on Front of
Computer
Yes
Restore CD/DVD Set Restore system to original factory shipping image – Can be obtained via Lenovo
Support
Cable Lock Support Yes, Optional Kensington Cable Lock
Serial, Parallel, USB, Yes
Audio, Network,
Enable/Disable Port
Control
Power-On Password Yes
Setup Password
Yes
NIC LEDs (integrated)Yes
Security Chip
Yes
Access Panel Key
Lock
Yes
Boot Sequence
Control
Yes
Padlock Support
Yes, loop in rear for optional padlock, prevents side panel removal
Boot without
keyboard and/or
mouse
Yes
Operating Environment
Air Temperature
•
Operating: 10°C to 35°C (50°F to 95°F)
•
Storage: -40°C to 60°C (-40°F to 140°F) in original shipping package
•
Storage: -10°C to 60°C (14°F to 140°F) without package
•
Note: The allowable upper temperature limit decreases by 1°C (1.8°F) for every 300 m (1000 ft)
above sea level.
Humidity
•
Operating: 10% to 80% (non-condensing)
•
Storage: 10% to 90% (non-condensing)
Altitude
•
Operating: -50 to 10 000 ft (-15.2 to 3 048 m)
Regulations and Standards
C30 is expected to be compliant to the Lenovo Standards Compliance Reference List
EMC
FCC (DoC)/Canada
CE (EMC)
VCCI
JEIDA
C-Tick
BSMI
CCIB
Safety
UL (C-UL)
TUV-GS
ISO-9241 – parts 3, 7, 8
NOM
IRAM
CCIB
PSB
CE (LVD)
Energy Star
All C30 systems are designed to with the premise of maximizing energy efficiency. Select models will meet the
workstation requirements outlined the Energy Star specification:
Energy Star Program Requirements for Computers: Version 6.0
EPEAT™
C30 models which are Energy Star 6.0 compliant will also qualify for the EPEAT™ Gold rating. The Development team is
currently assessing whether some or all of these models may also qualify for EPEAT™ Gold.
EuP Lot-6 2012
C30 systems are complaint with the EuP Lot-6 2012 standard for low power consumption. This is enabled by default for
all systems shipping to EMEA, and can be toggled on or off in the system BIOS.
SECTION II: SUPPORTED COMPONENTS
CPU Specifications
Part Description
2S Processor SKUs – These SKUs have 2 QPI links and are targeted for dual CPU systems, but will also work on single CPU systems
Intel Xeon E5-2690 – 8 cores, 2.9GHz, 8.0 QPI, 20MB Cache, DDR3-1600, Turbo+, HT, 135W
Intel Xeon E5-2680 – 8 cores, 2.7GHz, 8.0 QPI, 20MB Cache, DDR3-1600, Turbo+, HT, 130W
Intel Xeon E5-2670 – 8 cores, 2.6GHz, 8.0 QPI, 20MB Cache, DDR3-1600, Turbo+, HT, 115W
Intel Xeon E5-2665 – 8 cores, 2.4GHz, 8.0 QPI, 20MB Cache, DDR3-1600, Turbo+, HT, 115W
Intel Xeon E5-2660 – 8 cores, 2.2GHz, 8.0 QPI, 20MB Cache, DDR3-1600, Turbo+, HT, 95W
Intel Xeon E5-2650 – 8 cores, 2.0GHz, 8.0 QPI, 20MB Cache, DDR3-1600, Turbo+, HT, 95W
Intel Xeon E5-2667 – 6 cores, 2.9GHz, 8.0 QPI, 15MB Cache, DDR3-1600, Turbo+, HT, 130W
Intel Xeon E5-2640 – 6 cores, 2.5GHz, 7.2 QPI, 15MB Cache, DDR3-1333, Turbo+, HT, 95W
Intel Xeon E5-2630 – 6 cores, 2.3GHz, 7.2 QPI, 15MB Cache, DDR3-1333, Turbo+, HT, 95W
Intel Xeon E5-2620 – 6 cores, 2.0GHz, 7.2 QPI, 15MB Cache, DDR3-1333, Turbo+, HT, 95W
Intel Xeon E5-2643 – 4 cores, 3.3GHz, 8.0 QPI, 10MB Cache, DDR3-1600, Turbo+, HT, 130W
Intel Xeon E5-2609 – 4 cores, 2.4GHz, 6.4 QPI, 10MB Cache, DDR3-1067, 80W
Intel Xeon E5-2603 – 4 cores, 1.8GHz, 6.4 QPI, 10MB Cache, DDR3-1067, 80W
Intel Xeon E5-2637 – 2 cores, 3.0GHz, 8.0 QPI, 5MB Cache, DDR3-1600, Turbo+, HT, 80W
2S Low Power Processor SKUs – These SKUs have 2 QPI links and are targeted for dual CPU systems, but will also work on single
CPU systems. They also have a lower TDP than standard power CPUs.
Intel Xeon E5-2650L – 8 cores, 1.8GHz, 8.0 QPI, 20MB Cache, DDR3-1600, Turbo+, HT, 70W
Intel Xeon E5-2630L – 6 cores, 2.0GHz, 7.2 QPI, 15MB Cache, DDR3-1333, Turbo+, HT, 60W
1S Processor SKUs – These SKUs have 1 QPI link and are targeted for single CPU systems, will NOT work in dual CPU systems
When ordering two processors, the second processor must be the same as the first. Intel processor numbers are not a
measurement of higher performance. Processor numbers differentiate features within each processor family, not
across different processor families.
Quad, six and eight core technologies are designed to improve performance of multithreaded software products and
hardware-aware multitasking operating systems and may require appropriate operating system software for full
benefits; check with software provider to determine suitability; Not all customers or software applications will
necessarily benefit from use of these technologies.
64-bit computing on Intel® 64 architecture requires a computer system with a processor, chipset, BIOS, operating
system, device drivers, and applications enabled for Intel® 64 architecture. Processors will not operate (including 32bit operation) without an Intel® 64 architecture-enabled BIOS. Performance will vary depending on your hardware and
software configurations
RAM Specifications
Part Description
UDIMMs – 1333MHz
2GB DDR3 ECC UDIMM PC3-10600E (1333MHz) 1Rx8 2Gbit
4GB DDR3 ECC UDIMM PC3-10600E (1333MHz) 2Rx8 2Gbit
8GB DDR3 ECC UDIMM PC3-10600E (1333MHz) 2Rx8 4Gbit
UDIMMs – 1600MHz
2GB DDR3 ECC UDIMM PC3-10600E (1333MHz) 1Rx8 2Gbit
4GB DDR3 ECC UDIMM PC3-10600E (1333MHz) 2Rx8 2Gbit
8GB DDR3 ECC UDIMM PC3-10600E (1333MHz) 2Rx8 4Gbit
RDIMMs – 1333MHz
2GB DDR3 ECC RDIMM PC3-10600R (1333MHz) 1Rx8 2Gbit
4GB DDR3 ECC RDIMM PC3-10600R (1333MHz) 2Rx8 2Gbit
8GB DDR3 ECC RDIMM PC3-10600R (1333MHz) 2Rx4 2Gbit
16GB DDR3 ECC RDIMM PC3-10600R (1333MHz) 2Rx4 4Gbit
RDIMMs – 1600MHz
2GB DDR3 ECC RDIMM PC3-12800R (1600MHz) 1Rx8 2Gbit
4GB DDR3 ECC RDIMM PC3-12800R (1600MHz) 2Rx8 2Gbit
8GB DDR3 ECC RDIMM PC3-12800R (1600MHz) 2Rx4 2Gbit
16GB DDR3 ECC RDIMM PC3-12800R (1600MHz) 2Rx4 4Gbit
32GB DDR3 ECC RDIMM PC3-12800R (1600MHz) 2Rx4 4Gbit (performance is configuration dependant)
Memory Support Matrix
Storage – Hard Drive/SSD Specifications
Part Description
3.5″ SATA Hard Disk Drive (HDD)
250GB SATA – 7200rpm, 6Gb/s, 3.5″
500GB SATA – 7200rpm, 6Gb/s, 3.5″
1TB SATA – 7200rpm, 6Gb/s, 3.5″
2TB SATA – 7200rpm, 6Gb/s, 3.5″
3TB SATA – 7200rpm, 6Gb/s, 3.5″
2.5″ SATA Hard Disk Drive (HDD)
250GB SATA – 10000rpm, 6Gb/s, 2.5″
500GB SATA – 10000rpm, 6Gb/s, 2.5″
1TB SATA – 10000rpm, 6Gb/s, 2.5″
3.5″ SAS Hard Disk Drive (HDD)
300GB SAS – 15000rpm, 6Gb/s, 3.5″
450GB SAS – 15000rpm, 6Gb/s, 3.5″
600GB SAS – 15000rpm, 6Gb/s, 3.5″
2.5″ SAS Hard Disk Drive (HDD)
146GB SAS – 15000rpm, 6Gb/s, 2.5″
300GB SAS – 15000rpm, 6Gb/s, 2.5″
2.5″ SATA Solid State Drive (SSD)
128GB SATA – Solid State Drive (SSD), 6Gb/s, MLC, 2.5″
180GB SATA – Solid State Drive (SSD), 6Gb/s, MLC, 2.5″
240GB SATA – Solid State Drive (SSD), 6Gb/s, MLC, 2.5″
256GB SATA – Solid State Drive (SSD), 6Gb/s, MLC, OPAL, 2.5″
mSATA Drives
128GB mSATA Drive, 6Gb/s, MLC
256GB mSATA Drive, 6Gb/s, MLC
RAID
Supported RAID levels for a system will vary from the stated capabilities of the RAID controller due to dependencies
on the number and capacity of physical disks in the system and on customer requirements for performance, fault
tolerance, or data redundancy.
RAID levels and requirements:
•
RAID 0 (striping) provides increased performance by writing data across multiple drives.
•
RAID 1 (mirroring) provides fault tolerance by writing the data on two drives.
•
RAID 5 (striping with parity) uses distributed parity data to provide fault tolerance more efficiently
than RAID 1. Requires three or more drives.
•
RAID 10 (or RAID 1+0) combines
•
RAID 1 and RAID 0 to create a stripe of mirrors that is fault tolerant while offering increased
performance. Requires four drives.
Optional Hard Disk Drive Controllers:
LSI 9240-8i SATA/SAS RAID adapter
Description: PCIe x8 adapter card
Enables: Up to 5 SAS or SATA drives @ SATA3 (6GB/s) speeds, RAID 0,1,10
RAID 5 Support available with optional RAID key
SAS HDD enablement module (1-3 drives)
Description: S30 / C30 SAS HDD enablement module
Enables: Up to 3 SATA or SAS drives at SATA2 (3Gb/s) speeds, RAID 0,1
Storage – Optical Drive
Part Description
DVD-ROM Drive – 16x/48x (SATA)
DVD Burner/CD-RW Rambo Drive (SATA)
Blu-Ray Burner Drive w/AACS encryption (SATA)
Keyboard Specifications
Part Description
Preferred Pro Fullsize Keyboard (USB)
Pointing Devices Specifications
Part Description
Optical Wheel Mouse (800 DPI), USB – red wheel
Video Adapters Specifications
Part Description
NVIDIA NVS300 (DMS-59 to Dual DVI, DMS-59 to Dual DP) – 512MB GDDR3
NVIDIA NVS310 (Dual DP) 512MB DDR3
NVIDIA NVS450 (DPx4) – 512MB GDDR3
NVIDIA NVS 510 (mini DP x 4) – 2GB DDR3
NVIDIA Quadro 400 (Dual link DVI, DP) – 512MB DDR3
NVIDIA Quadro 410 (Dual link DVI, DP) 512MB DDR3
NVIDIA Quadro 600 (Dual link DVI, DP) – 1GB DDR3
NVIDIA Quadro K600 (Dual link DVI, DP) – 1GB DDR3
NVIDIA Quadro 2000 (Dual link DVI, DP, DP) – 1GB GDDR5
NVIDIA Quadro K2000 (Dual link DVI, DP, DP) – 2GB GDDR5
NVIDIA Quadro 2000D (Dual link DVI x 2) – 1GB GDDR5
NVIDIA Quadro K2000D (Dual link DVI x 2) – 2GB GDDR5
NVIDIA Quadro 4000 (Dual link DVI, DP, DP, Stereo 3D) – 2GB GDDR5
NVIDIA Quadro K4000 (Dual link DVI, DP, DP, Stereo 3D) – 3GB GDDR5
NVIDIA Quadro 5000 (Dual link DVI, DP, DP, Stereo 3D) – 2.5GB GDDR5
NVIDIA Quadro K5000 (Dual link DVI x 2, DP, DP) – 4GB GDDR5
NVIDIA Quadro 6000 (Dual link DVI, DP, DP, Stereo 3D) – 6GB GDDR5
SLI Implementations
2 x NVIDIA Quadro K5000 with SLI Cable
2 x NVIDIA Quadro 5000 with SLI Cable
2 x NVIDIA Quadro 5000
SLI Cable
Compute Adapters
NVIDIA Tesla C2075 – 6GB GDDR5
PCI/PCIe Adapters Specifications
Part Description
IEEE 1394a (Firewire-400) PCI Express x1 Adapter (2 external ports)
Intel 82574L Gigabit CT2 Desktop Ethernet Adapter
Intel 1 Gigabit ET Dual Port Server Adapter
USB 3.0 PCI Express x1 Adapter
SoundBlaster Recon3D Audio Card (PCIe x1)
Speakers Specifications
Part Description
Lenovo Branded 2-Piece Speaker Set
Speaker Brick
SECTION III: SYSTEM TECHNICAL SPECIFICATIONS
Power Supply Specifications
Power Supply
800w PSU
Operating Voltage Range
90-264 VAC
Rated Voltage Range
100-127V / 200-240V
Rated Line Frequency
50/60Hz.
Operating Line Frequency
Range
47Hz/63Hz
Rated Input Current
12A @ 100-127 VAC6A @ 200-240 VAC
Power Supply Fan
92x38mm, 2400rpm max
ENERGY STAR® qualified
(Config Dependent)
YES
80 PLUS Compliant
YES, 80 PLUS Gold
Built-in Self Test (BIST) LED YES
Surge Tolerant Full Ranging YES
Power Supply (withstands
power surges up to 2000V)
Click here to access the ThinkStation Power Calculator.
BIOS Specifications
Features
WMI Support
Compliant with Microsoft WBEM and the DMTF Common Information Model
ROM-Based Setup Utility (F1)
System Configuration Setup program available at power-on with F1 key
Bootblock Recovery
Recovers system BIOS when Flash ROM corrupted.
Replicated Setup
Saves System Configuration settings to file that can then be used replicated to other systems.
Boot Control
Boot control available through ROM-Based Setup Utility or with F12 key at power-on
Memory Change Alert
Power-on Error message in event of decrease in system memory
Thermal Alert
Power-on Error message in event of fan failure
Asset Tag
Support ability to set SMBIOS Type 2 Baseboard Asset Tag field.
System/Emergency ROM Flash
Recovery with Video
Support process to recover system BIOS when Flash ROM corrupted
Remote Wakeup/Remote
Shutdown
Sustem admin can power on/off a client computer from remote location to provide maintenance
Quick Resume time
Support lor power S3 (suspend to RAM) and prompt resume times
ROM revision level
System UEFI (BIOS) version reported in SMBIOS Type 0 structure and in BIOS Setup
Keyboard-less Operation
System can be booted without a keyboard
Per-port Control
Allows I/O ports to be individually enabled/disabled through ROM-based setup or WMI interface
Adaptive Cooling
Fans dynamically controlled by system BIOS based on temperature. User has ability to provide
custom fan control table
Security
User and Administrator passwords can protect boot and ROM-base Setup. Chassis intrusion detection
protect
Intel(R) AMT (includes ASF 2.0)
Allows system to be supported from a remote location
Intel(R) TXT
Intel(R) Trusted Execution Technology provides a security foundation to build protections against
software base attacks.
Memory modes
Supports mirroring, lock step, and sparing memory modes
Windows 8 ready
Supports Windows 8 requirements – Secure flash, UEFI v 2.3.1 spec
Industry Standard Specification Support
UEFI
Unified Extensible Firmware Interface v2.3.1
ACPI (Advanced Configuration
and power Management
Interface)
Advanced Configuration and Power Interface v4.0
ASF 2.0
DMTF Alert Standard Format Specification v2.0
ATA (IDE)
AT Attachment 6 with Packet Interface (ATA/ATAPI-6)
CD Boot
“El Torito” Bootable CD-Rom Format Specification, Version 1.0
EHCI
Enhanced Host Controller Interface for Universal Serial Bus, Revision 1.0
PCI
PCI Local Bus v3.0PC Firmware Specification 2.1
PCI Express
PCI Express Base Specification 3.0
SATA
Serial ATA Revision 3.0 Specification
TPM
Trusted Computing Group TPM Specification Version 1.2
UHCI
Universal Host Controller Interface Design Guide, Revision 1.1
USB
Universal Serial Bus Revision 1.1Universal Serial Bus v2.0Universal Serial Bus v3.0
SMBIOS
DMTF System Management Spec v2.7.1
Social and Environmental Responsibility
Quality Control
Lenovo is a member of an eco declaration system that enforces regular independent quality control
Hazardous substances and preparation
Products do not contain more than; 0.1% lead, 0.01% cadmium, 0.1% mercury, 0.1% hexavalent chromium,
0.1% polybrominated biphenyls (PBB) or 0.1% polybrominated diphenyl ethers (PBDE). (See legal
reference and Note B1
Products do not contain Asbestos
Products do not contain Ozone Depleting Substances: Chlorofluorocarbons (CFC),
hydrobromofluorocarbons (HBFC), hydrochlorofluorcarbons (HCFC), Halons, carbontetrachloride, 1,1,1trichloroethane, methyl bromide
Products do not contain more than; 0.005% polychlorinated biphenyl (PCB), 0.005% polychlorinated
terphenyl (PCT) in preparation
Products do not contain more than 0.1% short chain chloroparaffins (SCCP) with 10-13 carbon atoms in the
chain containing at least 48% per mass of chlorine in the SCCP
Parts with direct and prolonged skin contact do not release nickel in concentrations above 0.5
microgram/cm²/week
REACH Article 33 information about substances in articles is available at:
http://www.lenovo.com/social_responsibility/us/en/ThinkGreen_products.html#environment
Batteries
If the product contains a battery or an accumulator, it is labeled with the disposal symbol and if it contains
more than 0.0005% of mercury (for button cells only) by weight, or more than 0.004% of lead, it shall be
marked with the chemical symbol for the metal concerned, Hg or Pb. Information on proper disposal is
provided in user manual
Button cells used in the product do not contain more than 2% by weight of mercury. Other batteries or
accumulators do not contain more than 0.0005% of mercury or 0.002% of cadmium
Batteries and accumulators are easily removable by either users or service providers (as dependent on the
design of the product). Exception: Batteries that are permanently installed for safety, performance, medical
or data integrity reasons do not have to be “easily removable
Safety, EMC connection to the telephone network and labeling
The product complies with legally required safety standards as specified
The product complies with legally required standards for electromagnetic compatibility
If product is intended for connection to a public telecom network or contains a radio transmitter, it complies
with legally required standards for radio and telecommunication devices
The product is labeled to show conformance with applicable legal requirements
Product packaging
Packaging and packaging components do not contain more than 0.01% lead, mercury, cadmium and
hexavalent chromium by weight of these together.
Plastic packaging material is marked according to ISO 11469 referring ISO 1043
The product packaging material is free from ozone depleting substances as specified in the Montreal
Protocol
For more information on Lenovo social environmental practices
visit:http://www.lenovo.com/social_responsibility/us/en/ThinkGreen_products.html#environment
Manageability
Industry Standard
Specifications
This product meets the following industry standard specifications for manageability functionality:
•
Remote Manageability
Software Solutions
System Software Manager
Intel LAN with AMT
Lenovo ThinkStation is supported on the following remote manageability software consoles:
•
Lenovo ThinkManagement Console
•
LANDesk Management Suite for ThinkVantage Technologies (www.landesk.com/lenovo)
•
Microsoft System Center Configuration Manager
Lenovo ThinkStation supports software management tools from the ThinkVantage System Update
suite:
•
System Update
•
Update Retriever
•
Thin Installer
Service, Support, and
Warranty
On-site Warranty and Service: Three-years, limited warranty and service offering delivers on-site,
next business-day service for parts and labor and includes free telephone support 8am – 5pm.
Global coverage ensures that any product purchased in one country and transferred to another,
non-restricted country will remain fully covered under the original warranty and service offering.
Go to www.lenovo.com/support and www.lenovo.com/warranty for more details
SECTION IV: TECHNICAL SPECIFICATIONS
CPU Specifications
Part Description
2S Processor SKUs – These SKUs have 2 QPI links and are targeted for dual CPU systems, but will also work on single CPU systems
Intel Xeon E5-2690 – 8 cores, 2.9GHz, 8.0 QPI, 20MB Cache, DDR3-1600, Turbo+, HT, 135W
Intel Xeon E5-2680 – 8 cores, 2.7GHz, 8.0 QPI, 20MB Cache, DDR3-1600, Turbo+, HT, 130W
Intel Xeon E5-2670 – 8 cores, 2.6GHz, 8.0 QPI, 20MB Cache, DDR3-1600, Turbo+, HT, 115W
Intel Xeon E5-2665 – 8 cores, 2.4GHz, 8.0 QPI, 20MB Cache, DDR3-1600, Turbo+, HT, 115W
Intel Xeon E5-2660 – 8 cores, 2.2GHz, 8.0 QPI, 20MB Cache, DDR3-1600, Turbo+, HT, 95W
Intel Xeon E5-2650 – 8 cores, 2.0GHz, 8.0 QPI, 20MB Cache, DDR3-1600, Turbo+, HT, 95W
Intel Xeon E5-2667 – 6 cores, 2.9GHz, 8.0 QPI, 15MB Cache, DDR3-1600, Turbo+, HT, 130W
Intel Xeon E5-2640 – 6 cores, 2.5GHz, 7.2 QPI, 15MB Cache, DDR3-1333, Turbo+, HT, 95W
Intel Xeon E5-2630 – 6 cores, 2.3GHz, 7.2 QPI, 15MB Cache, DDR3-1333, Turbo+, HT, 95W
Intel Xeon E5-2620 – 6 cores, 2.0GHz, 7.2 QPI, 15MB Cache, DDR3-1333, Turbo+, HT, 95W
Intel Xeon E5-2643 – 4 cores, 3.3GHz, 8.0 QPI, 10MB Cache, DDR3-1600, Turbo+, HT, 130W
Intel Xeon E5-2609 – 4 cores, 2.4GHz, 6.4 QPI, 10MB Cache, DDR3-1067, 80W
Intel Xeon E5-2603 – 4 cores, 1.8GHz, 6.4 QPI, 10MB Cache, DDR3-1067, 80W
Intel Xeon E5-2637 – 2 cores, 3.0GHz, 8.0 QPI, 5MB Cache, DDR3-1600, Turbo+, HT, 80W
2S Low Power Processor SKUs – These SKUs have 2 QPI links and are targeted for dual CPU systems, but will also work on single
CPU systems. They also have a lower TDP than standard power CPUs.
Intel Xeon E5-2650L – 8 cores, 1.8GHz, 8.0 QPI, 20MB Cache, DDR3-1600, Turbo+, HT, 70W
Intel Xeon E5-2630L – 6 cores, 2.0GHz, 7.2 QPI, 15MB Cache, DDR3-1333, Turbo+, HT, 60W
1S Processor SKUs – These SKUs have 1 QPI link and are targeted for single CPU systems, will NOT work in dual CPU systems
HDD
3.5″ SAS Hard Disk Drive (HDD)
300GB SAS – 15000rpm, 6Gb/s, 3.5″
450GB SAS – 15000rpm, 6Gb/s, 3.5″
600GB SAS – 15000rpm, 6Gb/s, 3.5″
2.5″ SAS Hard Disk Drive (HDD)
146GB SAS – 15000rpm, 6Gb/s, 2.5″
300GB SAS – 15000rpm, 6Gb/s, 2.5″
Specification
3.5″ 15K
2.5″ 15K
Interface
Connector
SAS SFF-8482
Transfer Rate (Gb/sec)
3Gb
Spindle Speed(RPM)
15,000 +/-
Power off to Spindle Stop(sec)
30 max
DC Power to Drive Ready(sec)
30 max
Performance
15,000 +/-
Receipt of Start Unit Command to Drive Ready(sec) 30 max
Average Latency(msec)
2 +/- 0.25
Full Stroke Seek for Read/Write(ms max)
8/9
Input(VDC)
+5v +- 5%+12v +- 5%
Typical(Watts)
TBD
Idle(Watts)
TBD
Height(mm – Max)
26.11
15
Width(mm)
101.6 +/- 0.25
69.85 +/- 0.25
Depth(mm – Max)
146.99
100 +/- 0.45
Weight(grams)
800 max
Operating(C) Ambient
5 to 55
Operating(C) Base Casting
60 max
Non-Operating(C) Ambient
-40 to 70
Gradient(C per Hour)
20 max
Power Management
Dimensions
Temperature
Shock
Operating(Gs @ 2ms)
60 max
Non-Operating(Gs @ 2ms)
250 max
Part Description
3.5″ SATA Hard Disk Drive (HDD)
250GB SATA – 7200rpm, 6Gb/s, 3.5″
500GB SATA – 7200rpm, 6Gb/s, 3.5″
1TB SATA – 7200rpm, 6Gb/s, 3.5″
2TB SATA – 7200rpm, 6Gb/s, 3.5″
3TB SATA – 7200rpm, 6Gb/s, 3.5″
2.5″ SATA Hard Disk Drive (HDD)
150GB SATA – 10000rpm, 6Gb/s, 2.5″
300GB SATA – 10000rpm, 6Gb/s, 2.5″
600GB SATA – 10000rpm, 6Gb/s, 2.5″
2.5″ SATA Solid State Drive (SSD)
128GB SATA – Solid State Drive (SSD), 6Gb/s, MLC, 2.5″
256GB SATA – Solid State Drive (SSD), 6Gb/s, MLC, OPAL, 2.5″
mSATA Drives
128GB mSATA Drive, 6Gb/s, MLC
256GB mSATA Drive, 6Gb/s, MLC
Specification
Interface
Connector
SATA
Ports
Single
Transfer Rate
6Gb
Ambient (C)
0 to 55
Base Casting (C)
60 max
Temperature
Operational
Non-Operational
Gradient(C per Hour)
20 max
Ambient(C))
-40 to 70
Gradient(C per Hour)
30 max
Humidity
Operational
Relative Non-Condensing Wet bulb (%) 5 to 90
Gradient (% per hour)
Non-Operational
20
Relative Non-Condensing Wet bulb (%) 5 to 95
Gradient (% per hour)
20
Operating(feet)
-1000 to 10,000
Non-Operating(feet)
-1000 to 40,000
½ Sine @ 2ms (Read & Write) (G)
60
Rotational (Rad/sec**2)
8.5
½ Sine @ 2ms (G)
250
Rotational (Rad/sec**2)
20,000
Altitude
Shock – All Axis
OperationalNo Data loss. Data
recovery is allowed
Non-Operational No damage allowed
HDD Controller Specifications
LSI 9240-8i SATA/SAS RAID adapter
PCI Bus
PCI-Express 2.0 x8 lanes
PCI Modes
Bus Master DMA
RAID Levels
RAID 0, 1, 5, 10, 50 and JBOD mod
Data Transfer Rates
Up to 6 Gb/s per port
PCI Card Type
3.3V Add-in card
PCI Voltage
+12V ±10
PCI Power
13.5W
Bracket
Full Height and Low-Profile
Certification Level
PCI-Express 2.0
Internal Connectors
Two X4 Mini-SAS SFF8087 (vertical orientation
SSD Technical Specifications
Solid State Drives for Workstations
Capacity
128GB, 180GB, 240GB, 256GB
Physical Size
Model Height (mm) 6.80 ± 0.20
Width (mm) 69.85 ± 0.25
Length (mm) 100.00 ± 0.25
Weight (gram) Max 58
Interface
SATA
Synchronous
Transfer Rate
6Gb/s
Operating
Temperature
0°C to 60°C (32° to 140°F)
CD – RW Rambo Drive
Description
5.25-inch, half-height, tray-load
Mounting Orientation
Either horizontal or vertical
Interface Type
SATA/ATAPI
Dimensions
(WxHxD) 15.0 x 4.4 x 20.3 cm (5.9 x 1.7 x 8.0 in)
Disc Formats
DVD-RAMDVD+RDVD+RWDVD+R DLDVD-R DL
DVD-R
DVD-RW
CD-R
CD-RW
Disc Capacity
DVD-ROM
8.5 GB DL or 4.7 GB standard
Full Stroke DVD
< 250 ms (seek)
Full Stroke CD
< 210 ms (seek)
Maximum Data Transfer Rates
CD ROM Read
CD-ROM, CD-R Up to 40XCD-RW Up to 32X
DVD ROM Read
DVD-RAM Up to 12XDVD+RW Up to 8XDVD-RW Up to 8XDVD+R DL Up to 8XDVD-R DL Up to 8X
DVD-ROM Up to 16X
DVD-ROM DL Up to 8X
DVD+R Up to 16X
DVD-R Up to 16X
Power
Source
SATA DC power receptacle
DC Power Requirements 5 VDC ± 5%-100 mV ripple p-p12 VDC ± 5%-200 mV ripple p-p
DC Current
5 VDC – <1000 mA typical, <1600 mA maximum12 VDC – <600 mA typical, <1400 mAMaximum
Operating Environmental
Temperature
5° to 50° C (41° to 122° F)
Relative Humidity
10% to 90%
Maximum Wet Bulb Temperature
30° C (86° F)
Operating Systems Supported
Windows 7 Professional 32-bit and 64-bit,
Windows XP Professional or Windows XP Home 32*.
Red Hat Enterprise Linux(RHEL) 6
Desktop/Workstation. No driver is required for this device. Native support is provided by the operating system.
Kit Contents
SATA SuperMulti DVD Writer Drive, Roxio
Easy Media Creator software, Intervideo
WinDVD Software, installation guide, and
DVD+R media.
DVD – ROM Drive
Description
5.25-inch, half-height, tray-load
Mounting Orientation
Either horizontal or vertical
Interface Type
SATA/ATAPI
Dimensions
(WxHxD) 15.0 x 4.4 x 20.3 cm (5.9 x 1.7 x 8.0 in)
Disc Capacity DVD-ROM
Single layer: Up to 4.7 GB Double layer: Up to 8.5 GB
Access Times
DVD-ROM Single Layer
< 140 ms (typical)
CD-ROM Mode 1
< 125 ms (typical)
Full Stroke DVD
< 250 ms (seek)
Full Stroke CD
< 210 ms (seek)
Power
Source
SATA DC power receptacle
DC Power Requirements 5 VDC ± 5%-100 mV ripple p-p12 VDC ± 5%-200 mV ripple p-p
DC Current
5 VDC – <1000 mA typical, < 1600 mAmaximum12 VDC – < 600 mA typical, < 1400
mAmaximum
Operating Environmental
Temperature
5° to 50° C (41° to 122° F)
Relative Humidity
10% to 90%
Maximum Wet Bulb Temperature
30° C (86° F)
Operating Systems Supported
Windows 7 Professional 32-bit and 64-bit,
Windows XP Professional or Windows XP Home 32*.
Red Hat Enterprise Linux(RHEL) WS4**, 5, 6
Desktop/Workstation. No driver is required for this device. Native support is provided by the operating system.
Blu-Ray Burner Drive w/ AACS encryption
Description
5.25-inch, half-height, tray-load
Mounting Orientation
Either horizontal or vertical
Interface Type
SATA
Dimensions
(WxHxD) 15.0 x 4.4 x 20.3 cm (5.9 x 1.7 x 8.0 in)
Disc Formats
BD-ROMBD-RBD-REDVD-RAMDVD+R
DVD+RW
DVD+R DL
DVD-R DL
DVD-R
DVD-RW
CD-R
CD-RW
Disc Capacity
DVD-ROM
8.5 GB DL or 4.7 GB standard
Blu-ray
50 GB DL or 25 GB standard
Full Stroke DVD
< 250 ms (seek)
Full Stroke CD
< 210 ms (seek)
Blu-ray
<275 ms (seek)
Startup Time
BD-ROM (SL/DL) 25S / 28SBD-R (SL/DL) 25S / 28SBD-RE (SL/DL) 25S / 28SDVD-ROM
(SL/DL) 18S / 18SDVD-R (SL/DL) 25S / 25S
DVD-RW 25S
DVD+R (SL/DL) 25S / 25S
DVD+RW 25S
DVD-RAM 45SCD-ROM 45S
Maximum Data Transfer Rates CD CD-ROMCD-RCD-RWUp to 40XUp to 40XUp to 40X
ROM Read
DVD ROM Read
DVD-RAM Up to 5XDVD+RW Up to 10XDVD-RW Up to 10XDVD+R DL Up to 8XDVD-R DL
Up to 8X
DVD-ROM Up to 16X
DVD-ROM DL Up to 8X
DVD+R Up to 12X
DVD-R Up to 12X
Blu-Ray
BD-ROM Up to 6XBD-ROM DL Up to 4.8XBD-R Up to 6XBD-R DL Up to 4.8XBD-R Up to
6XBD-RE SL/DL Up to 4.8X
Power
Source
SATA DC power receptacle
DC Power Requirements
5 VDC ± 5%-100 mV ripple p-p12 VDC ± 10%-100 mV ripple p-p
DC Current
5 VDC -900 mA typical, 1200 mA maximum12 VDC -1000 mA typical, 1600 mA maximum
Operating Environmental
Temperature
5° to 50° C (41° to 122° F)
Relative Humidity
15% to 80%
Maximum Wet Bulb Temperature
30° C (86° F)
Operating Systems Supported
Windows 7 Professional 32-bit and 64-bit,
Windows XP, Professional or Windows XP Home 32*.
Red Hat Enterprise Linux(RHEL) WS 6
Kit Contents
Blue Laser RW Drive, Roxio Easy Media
Creator software, Intervideo WinDVD
Software, installation guide.
Disclaimer
As Blu-Ray is a new format containing new technologies, certain disc, digital connection, compatibility and/or
performance issues may arise, and do not constitute defects in the product. Flawless playback on all systems is not
guaranteed. In order for some Blu-Ray titles to play, they may require a DVI or HDMI digital connection and your
display may require HDCP support. HD-DVD movies cannot be played on this workstation.
Video Cards
NVIDIA NVS 300 512MB Graphics Card
Form Factor
2.7 inches (H) x 5.7 inches (L), Half-Height
Graphics Controller
NVIDIA NVS 300 Graphics Board
Bus Type
PCI Express x16, Generation 2.0
Memory
512 MB GDDR3 SDRAM unified graphics memory
Connectors
DMS-59
Includes DMS-59 to Dual DVI-I adapter or DMS-59 to Dual DP adapter
Maximum Resolution
DVI: two digital displays up to 1920 x 1200
DisplayPort: two digital displays up to 2560 x 1600
VGA: two analog displays up to 1920 x 1080
Image Quality Features
Display Output
This card support up to two displays: Drives DVI enabled digital displays at resolutions up to 1920 × 1200 at 60 Hz with
reduced blanking Drives DisplayPort enabled digital displays at resolutions up to 2560 × 1600 at 60 Hz with reduced
blanking (through optional DMS-59 to DisplayPort adapter)
Drives VGA enabled analog displays at resolutions up to 1920 x 1080 (through optional DMS-59 to VGA adapter)
Supported Graphics APIs
OGL 3.3
DirectX 10.1
Available Graphics Drivers
Genuine Windows 7 Professional (64-bit and 32-bit)
Microsoft Windows XP Professional (64-bit and 32-bit)
Red Hat Enterprise Linux(RHEL) 6 Desktop/Workstation
Power Consumption
<18 Watts
NVIDIA NVS 310 512MB Graphics Card
Form Factor
Low Profile: 2.713 inches in height × 6.150 inches in length
Graphics Controller
NVIDIA NVS 310
Bus Type
PCI Express x16, 2.0 compliant
Memory
Size: 512MB DDR3
Clock: 875Mhz
Memory Bandwidth: 14GB/s
Connectors
2 x DisplayPort 1.2
Maximum Resolution
Up to 2560 x 1600 (digital display) per display.
Image Quality Features
See Display Output section.
The following video formats are supported:
- MPEG2
- MPEG4 Part 2 Advanced Simple Profile
- H.264 SVC codec support
- Support for 3D Blu Ray
- VC1
- DivX version 3.11 and later
- MVC
A full range of video resolutions are supported including 1080p, 1080i, 720p, 480p and 480i. The NVS 310 GPU provides
hardware acceleration for the computationally intensive parts of video processing, as well as provides improved video
playback speeds via faster decode and transcode.
Display Output
Up to 2 displays in the following configurations:
Drives two DisplayPort enabled digital display at resolutions up to 2560 × 1600 at 60 Hz with reduced blanking, when
connected natively using the 2 DisplayPort connectors on the NVS 310 graphics card Supports 2 monitors up to
resolution of 1920 × 1200 at 60 Hz with reduced blanking using DisplayPort 1.2 multi stream topology technology.
DVI-D output:
Drives two digital display at resolutions up to 1920 × 1200 at 60Hz with reduced blanking using DisplayPort to DVI-D
single-link cable adaptors Drives two digital display at resolutions up to 2560× 1600 at 60 Hz with reduced blanking
using DisplayPort to DVI-D dual-link cable adaptors HDMI output:
NVS 310 is capable of driving two high definition (HD) panels up to resolutions of 1920 × 1080P at 60 Hz using
DisplayPort to HDMI cable adaptors
VGA display output:
Drives two analog display at resolutions up to 1920 × 1200 at 60 Hz using DisplayPort to VGA cable adaptors
Shading Architecture
Shader Model 5.0
Supported Graphics APIs
DX11, OpenGL 4.1
Available Graphics Drivers
Genuine Windows 7 Professional (64-bit and 32-bit)
Microsoft Windows XP Professional (64-bit and 32-bit)
Red Hat Enterprise Linux(RHEL)
Power Consumption
19.5 Watts
Note
The thermal solution used on this card is an active fan heatsink.
NVIDIA Quadro NVS 450
512 MB PCIe Graphics Card
Form Factor
ATX Full Height, 1/2 length Passive cooling
Bus Type
PCI Express x16, Generation 2.0
Memory
512 MB GDDR3 (256MB per GPU)
Connectors
Four DisplayPort;
Maximum Resolution
DisplayPort connectors support ultra-high-resolution panels (up to 2560 x 1600)
NOTE: This card supports up to four displays
Supported Graphics APIs
OpenGL 3.0
DirectX 10.0
Available Graphics Drivers
Genuine Windows 7 Professional (64-bit and 32-bit)
Microsoft Windows XP Professional (64-bit and 32-bit)
Red Hat Enterprise Linux(RHEL) 6 Desktop/Workstation
NVIDIA Quadro NVS 510
CUDA Cores
192
Memory Size Total
2.0 GB DDR3
Memory Interface
128-bit
Memory Bandwidth (GB/sec)
28.5
Display Connector
Mini DisplayPort (mDP)
# of Connectors
4
DisplayPort
4
Single-Link DVI-D
41
Dual-Link DVI-D
42
VGA
43
Maximum Display Resolution (Digital @ 60Hz)
3840×21604
Maximum Display Resolution (Analog @ 60 Hz)
1920×12005
Number of Slots
1
Audio Support (via DisplayPort)
✓
1 using mDP to SL-DVI, or included mDP-DP Cable with a DP to SL-DVI Cable Adaptor
2 using included mDP-DP cable with DP to DL-DVI Cable Adaptor
3 using included mDP-DP cable with DP to VGA Cable Adaptor
4 Through native DisplayPort (DP)
5 Through DP to VGA Cable Adaptor
NVIDIA Quadro 400 512MB Graphics Card
Form Factor
Low Profile, 2.7 inches (H) x 5.6 inches (L)
Graphics Controller
NVIDIA Quadro 400 Graphics Board
Bus Type
PCI Express x 16, Generation 2.0
Memory
512MB DDR3 SDRAM
Connectors
One (1) Dual-link DVI-I
One (1) DisplayPort 1.1
Maximum Resolution
DisplayPort 1.1: 2560 x 1600 @ 60 Hz
Dual Link DVI-I: 2560 x 1600 @ 60 Hz
Analog: 2048 x1536 @ 85 Hz
RAMDAC
Dual internal 400 MHz DACs
Display Output
This card supports up to two displays
Supported Graphics APIs
OpenGL 3.2
DirectX 10.1 Shader Model 4.1
Available GraphicsDriversGenuine Windows 7 Professional (64-bit and 32-bit)
Microsoft Windows XP Professional (64-bit and 32-bit)
Red Hat Enterprise Linux(RHEL) 6 Desktop/Workstation
Power Consumption
< 35 Watts
NVIDIA Quadro 410 512MB Graphics
Form Factor
Low Profile: 2.713 inches × 5.7 inches, single slot
Graphics Controller
NVIDIA Quadro 410
Bus Type
PCI Express x16, 3.0 compliant
Memory
Size: 512MB DDR3
Clock: 900MHz
Memory Bandwidth: 14GB/s
Connectors
One dual-link DVI-I connector
One DisplayPort connector
Maximum Resolution
Up to 2560 x 1600 (digital display) per display.
RAMDAC
400 MHz integrated RAMDAC
Display Output
Maximum resolution over DisplayPort: 2560 × 1600 × 32 bpp at 60 Hz (reduced blanking)
Maximum resolution over DVI port: 2560 × 1600 × 32 bpp at 60 Hz (reduced blanking)
Maximum resolution over VGA (through DVI to VGA cable): 2048 × 1536 × 32 bpp at 85 Hz
Shading Architecture
Shader Model 5.0
Supported Graphics APIs
DX11, OpenGL 4.2
Available Graphics Drivers
Genuine Windows 7 Professional (64-bit and 32-bit)
Microsoft Windows XP Professional (64-bit and 32-bit)
Red Hat Enterprise Linux(RHEL) 6 Desktop/Workstation
Power Consumption
< 35 Watts
NVIDIA Quadro 600 1GB Graphics Card
Form Factor
2.731″ H x 6.6″ L
Single Slot
Small Form Factor
Graphics Controller
NVIDIA Quadro 600 Graphics Card
Bus Type
PCI Express 2.0 x16
Memory
1 GB GDDR3
128-bit
Connectors
1 DVI-I output, 1DisplayPort output
Maximum Resolution
DisplayPort (up to 2560 x 1600 @ 60Hz and 1920×1200 @ 120Hz)
Dual-link DVI-I output (up to 2560 x 1600 @ 60Hz and 1920×1200 @ 120Hz)
Shading Architecture
Shader Model 5.0
Supported Graphics APIs
OpenGL 4.0
DirectX 11
CUDA API support includes:
CUDA C, CUDA C++, DirectCompute 5.0, OpenCL, Java, Python, and Fortran
Available Graphics Drivers
Genuine Windows 7 Professional (64-bit and 32-bit)
Microsoft Windows XP Professional (64-bit and 32-bit)
Red Hat Enterprise Linux(RHEL) 6 Desktop/Workstation
Power Consumption
40 Watts
NVIDIA Quadro 2000 1GB Graphics Card
Form Factor
4.376″ H x 7″ L
Single Slot
Graphics Controller
NVIDIA Quadro 2000 Graphics Card
Bus Type
PCI Express 2.0 x16
Memory
1 GB GDDR5
128-bit
Connectors
1 DVI-I output, 2 DisplayPort outputs
Maximum Resolution
Dual DisplayPort (up to 2560 x 1600 @ 60Hz and 1920×1200 @ 120Hz) Dual-link DVI-I output (up to 2560 x 1600 @ 60Hz
and 1920×1200 @ 120Hz)
Image Quality Features
Up to 16K x16K texture and render processing
Transparent multisampling and super sampling
16x angle independent anisotropic filtering
128-bit floating point performance
32-bit per-component floating point texture filtering and blending Support for any combination of two connected
displays DisplayPort 1.1a, HDMI 1.3a, and HDCP support
NVIDIA® 3D Vision™ technology, 3D DLP, Interleaved, and other 3D stereo format support Full OpenGL quad buffered
stereo support Underscan/overscan compensation and hardware scaling NVIDIA® nView® multi-display technology
Shading Architecture
Shader Model 5.0
Supported Graphics APIs
OpenGL 4.0
DirectX 11
CUDA API support includes:
CUDA C, CUDA C++, DirectCompute 5.0, OpenCL, Java, Python, and Fortran
Available GraphicsDrivers
Genuine Windows 7 Professional (64-bit and 32-bit)
Microsoft Windows XP Professional (64-bit and 32-bit)
Red Hat Enterprise Linux(RHEL) 6 Desktop/Workstation
Power Consumption
62 Watts
NVIDIA Quadro 2000D (Spec DVI only card)
Form Factor
4.376″ H x 7″ L
Single Slot
Graphics Controller
NVIDIA Quadro 2000D Graphics Card
Bus Type
PCI Express 2.0 x16
Memory
1 GB GDDR5
128-bit
Connectors
2 Dual Link DVI outputs
Maximum Resolution
Dual-link DVI output (up to 2560 x 1600 @ 60Hz and 1920×1200 @ 120Hz)
Image Quality
Features Up to 16K x16K texture and render processing
Transparent multisampling and super sampling
16x angle independent anisotropic filtering
128-bit floating point performance
32-bit per-component floating point texture filtering and blending
Support for any combination of two connected displays
Dual Link DVI, HDMI 1.3a, and HDCP support
NVIDIA® 3D Vision™ technology, 3D DLP, Interleaved, and other 3D stereo format support
Full OpenGL quad buffered stereo support
Underscan/overscan compensation and hardware scaling
NVIDIA® nView® multi-display technology
Shading Architecture
Shader Model 5.0
Supported Graphics APIs
OpenGL 4.0
DirectX 11
CUDA API support includes:
CUDA C, CUDA C++, DirectCompute 5.0, OpenCL, Java, Python, and Fortran
Available Graphics Drivers
Genuine Windows 7 Professional (64-bit and 32-bit)
Microsoft Windows XP Professional (64-bit and 32-bit)
Red Hat Enterprise Linux(RHEL) 6 Desktop/Workstation
Power Consumption
62 Watts
NVIDIA Quadro 4000 2GB Graphics Card
Form Factor
4.376″ H x 9.50″ L
Single Slot
Graphics Controller
NVIDIA Quadro 4000 Graphics Card
Bus Type
PCI Express 2.0 x16
Memory
2 GB GDDR5
256-bit
Connectors
1 DVI-I output, 2 DisplayPort outputs;
Stereo bracket included
Maximum Resolution
Dual DisplayPort (up to 2560 x 1600 @ 60Hz and 1920×1200 @ 120Hz)
Dual-link DVI-I output (up to 2560 x 1600 @ 60Hz and 1920×1200 @ 120Hz)
RAMDAC
400 MHz integrated RAMDAC
Image Quality Features
Up to 16K x16K texture and render processing
Transparent multisampling and super sampling
16x angle independent anisotropic filtering
128-bit floating point performance
32-bit per-component floating point texture filtering and blending
Support for any combination of two connected displays
DisplayPort 1.1a, HDMI 1.3a, and HDCP support
NVIDIA 3D Vision™ technology, 3D DLP, Interleaved, and other
3D stereo format support
Full OpenGL quad buffered stereo support
Underscan/overscan compensation and hardware scaling
NVIDIA nView® multi-display technology
Shading Architecture
Shader Model 5.0
Supported Graphics APIs
OpenGL 4.0
DirectX 11
CUDA API support includes:
CUDA C, CUDA C++, DirectCompute 5.0, OpenCL, Java, Python, and Fortran
Available GraphicsDrivers
Genuine Windows 7 Professional (64-bit and 32-bit)
Microsoft Windows XP Professional (64-bit and 32-bit)
Red Hat Enterprise Linux (RHEL) 6 Desktop/Workstation
Power Consumption
142 Watts
NVIDIA Quadro 5000 2.5GB Graphics Card
Form Factor
4.376″ H x 9.75″ L
Dual Slot
Graphics Controller
NVIDIA Quadro 5000 Graphics Card
Bus Type
PCI Express 2.0 x16
Memory
2.5 GB GDDR5 320-bit
Connectors
DVI-I (1), DP (2), Stereo (1)
Maximum Resolution
Dual DisplayPort (up to 2560 x 1600 @ 60Hz and 1920×1200 @ 120Hz)
Dual-link DVI-I output (up to 2560 x 1600 @ 60Hz and 1920×1200 @
120Hz)
Image Quality Features Up to 16K x16K texture and render processing
Transparent multisampling and super sampling
16x angle independent anisotropic filtering
128-bit floating point performance
32-bit per-component floating point texture filtering and blending
Support for any combination of two connected displays
DisplayPort 1.1a, HDMI 1.3a, and HDCP support
NVIDIA 3D Vision™ technology, 3D DLP, Interleaved, and other
3D stereo format support
Full OpenGL quad buffered stereo support
Underscan/overscan compensation and hardware scaling
NVIDIA nView® multi-display technology
Shading Architecture
Shader Model 5.0
Supported Graphics APIs
OpenGL 4.0
DirectX 11
CUDA API support includes:
CUDA C, CUDA C++, DirectCompute 5.0, OpenCL, Java, Python, and Fortran
Available Graphics Drivers
Genuine Windows 7 Professional (64-bit and 32-bit)
Microsoft Windows XP Professional (64-bit and 32-bit)
Red Hat Enterprise Linux (RHEL) 6 Desktop/Workstation
Power Consumption
152 Watts
NVIDIA Quadro K5000 4GB Graphics Card
CUDA Cores
1536
Single Precision Compute Performance
2.1 Teraflops
Memory Size Total
4GB GDDR5
Memory Interface
256-bit
Memory Bandwidth (GB/sec)
173 GB/s
Dual Link DVI-I
1
Dual Link DVI-D
1
DisplayPort 1.2
2
# of Digital Outputs
4
Stereo (3-pin Mini-DIN)
Optional
Maximum Display Resolution (Digital)
DVI-DL: Up to 330M Pixels/sec: (ex 1920×1200@120Hz, 2560×1600@60Hz)
DisplayPort 1.2: Up to 540M Pixels/sec & 17.3 Gbps data rate
(ex 3840×2160@60Hz 30bpp, 2560×1440@120Hz 30bpp, 4096×2160@24Hz 36bpp, 4096×2160@50Hz 30bpp )
NVIDIA Quadro 6000 6GB Graphics Card
Form Factor
4.376″ H x 9.75″ L
Dual Slot
Graphics Controller
NVIDIA Quadro 6000 Graphics Card
Bus Type
PCI Express 2.0 x16
Memory
6 GB GDDR5
384-bit
ECC Memory
Connectors
1 DVI-I output, 2 DisplayPort outputs, 1 Stereo(3-pin mini DIN);
One DP to DVI adapter included with card
DVI to VGA, DisplayPort to VGA and DisplayPort to dual link DVI
adapters available as accessories
Maximum Resolution
Dual DisplayPort (up to 2560 x 1600 @ 60Hz and 1920×1200 @ 120Hz)
Dual-link DVI-I output (up to 2560 x 1600 @ 60Hz and 1920×1200 @
120Hz)
Image Quality Features
30-bit color
Up to 16K x16K texture and render processing
Transparent multisampling and super sampling
16x angle independent anisotropic filtering
128-bit floating point performance
32-bit per-component floating point texture filtering and blending
64x full scene antialiasing (FSAA) / 128x FSAA in SLI Mode
Support for any combination of two connected displays
DisplayPort 1.1a, HDMI 1.3a, and HDCP support
NVIDIA 3D Vision™ technology, 3D DLP, Interleaved, and other
3D stereo format support
Full OpenGL quad buffered stereo support
Underscan/overscan compensation and hardware scaling
NVIDIA nView® multi-display technology
Shading Architecture
Shader Model 5.0
Supported Graphics APIs
OpenGL 4.0
DirectX 11
CUDA API support includes:
CUDA C, CUDA C++, DirectCompute 5.0, OpenCL, Java, Python, and Fortran
Available Graphics Drivers
Genuine Windows 7 Professional (64-bit and 32-bit)
Microsoft Windows XP Professional (64-bit and 32-bit)
Red Hat Enterprise Linux (RHEL) 6 Desktop/Workstation
Power Consumption
<250 Watts
NVIDIA Tesla C2075 Compute Processor
Form Factor
4.376 inches by 9.75 inches
Dual Slot
System Interface
PCI Express Gen2 ×16
Video Outputs
One Dual Link DVI-I
(Video output on this connector is not supported in Maximus configurations per NVIDIA)
Memory
6GB GDDR5
Peak Memory Bandwidth
+170 GB/s
Supported APIs
CUDA API support includes:
CUDA C, CUDA C++, DirectCompute 5.0, OpenCL, Java, Python, and Fortran
Supported Operating Systems
Genuine Windows 7 Professional (64-bit)
Genuine Windows Vista Business (64-bit)
Microsoft Windows XP Professional (64-bit)
Red Hat Enterprise Linux (RHEL) 6 Desktop/Workstation (64-bit)
Processor Cores
448 CUDA cores
Power Consumption
~215 Watts
Audio Devices
SoundBlaster Recon3D Audio Card (PCIe x1)
24-bit Analog-to-Digital conversion of analog
inputs
96kHz sample rate
24-bit Digital-to-Analog conversion of digital
sources
96kHz to analog
16-bit to 24-bit recording sampling rates
8,11.025,16, 22.05, 24, 32, 44.1, 48 and 96kHz
16-bit to 24-bit playback sampling rates
8,11.025,16, 22.05, 24, 32, 44.1, 48, 96 and
192kHz
Rear Panel Connectivity
Line in / Microphone In: Shared 1/8″ mini jack
Headphone: 1 x 1/8″ mini jack
Speaker Out: 3x 1/8″ mini jacks
Optical Out: TOSLINK
Optical In: TOSLINK
Speaker Support
Stereo/2.1 Speakers
5.1 Speakers
Headphones
Bus Connection
PCI Express 1x
Package Contents
Sound Card
Quick Start leaflet
Installation CD containing:
• Drivers for Windows®
• Creative Software Suite
• User’s Guide
Software
Sound Blaster Recon3D PCIe Control Panel
• THX® TruStudio Pro™ effects
• THX® TruStudio Pro Surround™
• THX® TruStudio Pro Crystalizer™
• THX® TruStudio Pro Bass™
• THX® TruStudio Pro Smart Volume™
• THX® TruStudio Pro Dialog Plus™
CrystalVoice effects
• CrystalVoice™ Acoustic Echo Cancellation
• CrystalVoice™ Noise Reduction
• CrystalVoice™ Smart Volume
• CrystalVoice™ FX
• CrystalVoice™ Focus
EAX Advanced HD
OpenAL
Creative Alchemy
Minimum System Requirements
Intel® Core™ 2 Duo or AMD® equivalent processor,
2.2 GHz or faster
Intel®, AMD® or 100% compatible motherboard
Microsoft® Windows® 7 (32/64-bit)
1 GB RAM
600 MB of free hard disk space
Available PCI Express® (x1, x4 or x16) slot
Available CD-ROM or DVD-ROM drive
Networking
Intel 82574L Gigabit CT2 Desktop Ethernet Adapter
Connector
RJ-45
Controller
Intel 82574L
Memory
Integrated Dual 48K configurable transit receive FIFO Buffers
Data Rates Supported
10/100/1000 Mbps
Compliance
IEEE 802.1p, Quality of Service (QoS) Support
Bus Architecture
PCI-E 1.1
Typical Power Consumption
1.9W
Operating Temperature
32º to 131º F (0º to 55º C)
Storage Humidity
90% at 35ºC
Dimensions (H x W x D)
12cm x 5.53cm x 11.92cm
Operating System Driver
Support
Windows 7 Professional 32-bit and 64-bit, Windows XP Professional 64bit, Red Hat Enterprise Linux 4 (4.8 or newer), 5 (5.3 or newer), 6
Intel 1 Gigabit ET Dual Port Server Adapter
Cabling Type
Category-5 up to 100m
Bracket Height
Low Profile & Full Height
Max TDP
2.9 W
Networking Specifications
# of Ports
Dual
System Interface Type
PCIe v2.0 (2.5GT/s)
Intel® Virtualization Technology for Connectivity
(VT-c)
VMDq, VMDc
Speed & Slot Width
2.5 GT/s, x4 Lane
Controller
Intel 82576
USB 3.0
Interface:
Single-Lane (x1) PCI Express Gen2
Mode:
Universal Serial Bus 3.0
Controller:
Renesas (NEC) μPD720200
PCB Version:
Ver1.1
Port:
2 external USB3.0 ports
Speed:
Data Transfer rate of 1.5/12/480/5000 Mbps.
Low Speed (1.5Mbps), Full Speed(12Mbps), High Speed(480Mbps), Super
Speed(5Gpbs)
Power Output:
+5V / 900mA (each port)
Bracket:
Standard 121mm / Low Profile 79.2mm
O.S. support:
Windows XP/2003/Vista/7/2008, (32/64-bit)
Linux 2.6.31 or later (Linux OS already implemented USB3.0 driver)
Environment:
Operation temp. 0 °C ～ 57 °C
Operation humidity:
5 ～ 95% RH
Storage temp.
-20 °C ～ 85 °C
IEEE 1394a (Firewire-400) PCI Express x1 Adapter
Data Transfer Rate
Supports up to 400 Mbps
Devices Supported
IEEE-1394 compliant devices
Bus Type
PCIe card full height PCIe slots
Ports
One IEEE-1394a 6-Pin Connector
System Requirements
Windows 7 Professional 32-bit and 64-bit, Microsoft® Windows® XP
Professional. Not supported on Linux. Pentium® III or higher processor 128-MB RAM 1-GB Hard
Drive CD-ROM drive Built in sound system Available PCI slot
Temperature –Operating50° to 131° F (10° to 55° C)
Temperature – Storage –22° to 140° F (–30° to 60° C)
Relative Humidity –
Operating
20% to 80%
Compliances
FCC Part 15B, cULus 60950, CE Mark EN55022B(1995)/EN55024-1998 STD, Taiwan BSMI
CNS13438, Korea MIC
Operating Systems
Supported
Windows 7 Professional 32-bit and 64-bit,Windows® XP Professional, XP Professional 64-bit.Not
supported on Linux