Download C-DG-IR9970HD User Manual from HENRY
Transcript
Panasonic 1080P HD-SDI CAMERA C-DG-IR9970HD WARRANTY Product GIMBAL DOME CAMERA Purchase Address Dealer ▶ Model Serial No. Customer Warranty Period: 2 years C-DG-IR9970HD Representative Please contact purchasing office or service center when you find any damage or problem with this product. ▶ The warranty period is 2 years from Invoice date. ◈A/S without cost◈ Within Warranty Period When damages occurred in nomal working environment Key Features: ◈A/S with cost◈ Damage by customer’s negligence ∙ 1/3" 2.1Megapixel Panasonic CMOS ∙ Mode 1080P(1920 X 1080) ∙ ACCE(Adaptive Color & Contrast Enhancement) ∙ WDR/BLC/HLC/D‐ZOOM/DNR SPECIFICATION DESCRIPTION Imaging Device Effective Pixels Scanning System Synchronization Horizontal Resolution Video Output S/N Ratio Min. Illumination IRIS Adjustment LENS Electronic Shutter IR LEDs Gama Characteristic IR Distance Auto Gain Control Day&Night Privacy Masking 3D-DNR Digital Zoom SENS-UP MOTION Digital Effect Dimension (mm) Weight(g) Input Voltage Power Consumption Operating Temp/Hum. Storage Temp. / Hum. Repair or Replace Warranty details Within warranty After Warranty Product A/S without cost Product exchange PAL 1/3" 2.1Megapixel Panasonic CMOS 1080P(1920 X 1080) Progressive Scan Internal, Negative Sync 1080P(1920 X 1080) HD-SDI /1.0 Vp-p (75Ω,Composite) More than 50dB (AGC Off) 1.0Lux(Color),0.5Lux(BW) Auto 2.8~12 Manual Zoom Lens Auto/FLK/1/25,30sec ~ 1/60000sec MANUAL(X2~X512) 72Pcs LEDs 0.45 60 Meters Auto Auto On / Off (Programmable) LEVEL(0~100)Adjustment 1.0X-8.0X 0FF/ X2-X8 ON/OFF OFF / V-FLIP / MIRROR / ROTATE 131x93(H) 800 DC 12V(±10%) IR OFF : 210mA / IR ON : 550mA(±10%) -10ºC~ +50ºC / 30% ~ 80% RH -20ºC ~ +60ºC / 20% ~ 90% RH 1. Damage by chargeabl 2. Damage by e case 3. Damage by even 4. Damage by within adapter. warranty 5. Damage by 6. Damage by customer’s careless handling natural disaster (Fire, Flood, etc.) not keeping the cautions and instructions on manual not using appointed power(frequency, voltage) or disassemble or cleaning by customer repairment by a person excepting the dealer DIMENSION Warranty details A/S with cost CONNECTING OF CAMERA CAUTION IN INSTALLATION ♣ Do not install the camera opposite of the sun so that it be avoided direct light. ♣ Be careful not to drop this camera and not to impact on it. CCTV camera is a precision device. ♣ Do not pull the cable. If you pull the cable, it will make electrical problems such as disconnection. ♣ The camera should be worked within a range of the allowable temperature that refers to specification. 1. No Picture after providing power. May be the power supply voltage abnormity, please check the power supply voltage and pole whether exactitude. Please check all the connecting cable and monitors whether be connected correctly or not. 2. The picture level direction have flowing interference ripples. May be caused by the power supply AC ripples, it need filter the wave of the power supply. Check the monitor and peripheral equipments used 3. The picture background color changes continuously. The fluorescent lamp’s electromagnetic field cause color roll. This is proper phenomenon of the cameras. Reduce the fluore scent lamp numbers or increase the distance between the camera and the fluorescent lamps can improve it. Use power supply external sync. camera can solve it. ♣ Do not try to fix even if the camera does not work. ♣ Installation this camera at safety place where is no water, If the camera has some problems with water accidently. You have to contact A/S centre that sold the camera to you. ♣ If you would like to relocate the already installed product, be sure to turn off the power and then move or reinstall it. ♣ Please contact the nearest A/S centre if you find out any Problems. Please do not ignore any small problems they can become a big problem. 4. The picture smear too mass . The power supply’s voltage unstable. Connecting cables not connect correctly or have high impedance. Feature Summary & OSD Setting CAUTION * Sensor (CMOS) 1/3" 2.1Megapixel Panasonic CMOS * Auto Gain Control (AGC) Built-in auto gain control (AGC) circuit. The color camera can get high definition picture in low Lux condition. * Scanning Mode NTSC or PAL mode. To prevent fire or shock hazarded. Do not expose the unit rain to rain or moisture. * OSD SETTING: The symbol is intended to alert the user to the presence of uninsulated ‘dangerous voltage’ within the product’s enclosure that may be of sufficient Magnitude to constitute a risk of electric shock to persons. The symbol is intended to alert the user to the presence of important important operating and maintenance (servicing) Instructions in the literature accompanying the appliance. CAUTION: RISK OF ELECTRIC. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO OUALIFIED SERVICE PERSONNEL. CAUTION: To prevent electric shocks and risk of fire hazards, do NOT use other than specified power source. Note: ● Please note the camera’s operating temperature and its using environment requirement. Avoid using the camera at too high or too low temperatures. The operating temperature is ‐30~+60℃. (Recommendatory operating temperature is ‐10~+50℃.) ● Never make the camera face the sun or bright object. Otherwise, it will