Download User Manual

6-2. Event type list
6. Supplement
Thermocouple
6-1. Measuring range list
Input type
*1 B
R
S
K1
K2
K3
E
J
T
N
PLII
WRe5-26
U
L
K
AuFe-Cr
K
AuFe-Cr
R.T.D.
Pt100
(New)
JIS/IEC
JPt100
(Old)
JIS
mV -10
0
0
0
10
0
V
-1
0
0
0
1
0
0
mA
4
10
10
20
50
50
100
1
1
2
5
5
10
20
20
Code
01
02
03
04
05
06
07
08
09
10
11
12
13
14
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
01
02
03
04
05
06
01
02
03
04
05
06
01
02
Event type
code
Measuring range
1800 °C
0
1700 °C
0
1700 °C
0
-100.0
400.0 °C
0.0
800.0 °C
-200
1200 °C
0
700 °C
0
600 °C
-199.9
200.0 °C
0
1300 °C
0
1300 °C
0
2300 °C
200.0 °C
-199.9
0
600 °C
-200
-100.0
-100.0
-50.0
0.00
0.0
0.0
0.0
-200
-100.0
-100.0
-50.0
0.00
0.0
0.0
0.0
Code
600 °C
100.0 °C
300.0 °C
50.0 °C
50.00 °C
100.0 °C
200.0 °C
500.0 °C
500 °C
100.0 °C
300.0 °C
50.0 °C
50.00 °C
100.0 °C
200.0 °C
500.0 °C
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Measuring range
3300 °F
0
3100 °F
0
3100 °F
0
-150
750 °F
0
1500 °F
-300
2200 °F
0
1300 °F
0
1100 °F
-300
400 °F
0
2300 °F
0
2300 °F
0
4200 °F
400 °F
-300
0
1100 °F
10.0
350.0 K
0.0
350.0 K
10
350 K
0
350 K
-300
1100 °F
-150.0
200.0 °F
-150
600 °F
-50.0
120.0 °F
0.0
120.0 °F
0.0
200.0 °F
0.0
400.0 °F
1000 °F
0
-300
1000 °F
-150.0
200.0 °F
-150
600 °F
-50.0
120.0 °F
0.0
120.0 °F
0.0
200.0 °F
0.0
400.0 °F
0
1000 °F
1
measuring
Higher limit absolute value Within
range
Higher limit value of
measuring range
2
Lower limit absolute value
Within measuring
range
Lower limit value of
measuring range
3
Higher limit deviation value -1999
9999 Unit
2000 Unit
4
Lower limit deviation value
-1999
9999 Unit
-1999 Unit
5
Out of higher and lower
limit ranges
0
9999 Unit
2000 Unit
6
Within higher and lower
limit ranges
0
9999 Unit
2000 Unit
7
Scaleover
EV output continues when scaleover occurs.
8
Heater break
Event output continues when heater break alarm is
output.
1
2
3
4
OFF
5
6
ON
OFF
: Set value for action
: SV value
NOTE: Code 8 in the above table can be selected and set only
when the instrument includes the heater break alarm option.
6-3. Event standby action
• In case an event output is used as an alarm, set “oFF,” “1,” “2,”
or “3.”
• In case an event output is used as control output, set “4.”
If scaleover occurs on the event set value side, however, event
output remains OFF during standby.
• When “1” has been set for event action, the standby action
functions when:
1. power is applied.
• When “2” has been set for standby action, the standby action
functions when:
1. power is applied;
2. STBY→ EXE;
• When “3” has been set for standby action, the standby action
functions when:
1. power is applied;
2. STBY→ EXE;
3. SV is changed where standby set value is a deviation value.
(Except during remote input, though.)
• When the standby action setting is changed to “oFF” or “4”
while standby is in action, the standby action is cancelled
immediately.
• If, upon applying power, PV value is out of the range in which
event action is ON, standby action becomes void even when
“1,” “2,” or “3” has been set for it.
Scaling range: -1999 9999 count
Span: 10 5000 count
but lower limit side<higher limit side
*1 Thermocouple B: 400 °C and 750 °F
or below is not covered by accuracy
guarantee.
Note: The following codes represent the respective factory-set
measuring ranges.
Code
05
07
02
05
02
Initial value of event
set value
ON
The scaling function allows you to select
any value within the following ranges:
Input
Standard/rating
JIS K
Thermocouple
JIS Pt100
R.T.D.
0 10mV DC
Voltage(mV)
1 5V DC
Voltage(V)
4 20mA DC
Current (mA)
Setting range of
event set value
Event type
Measuring range
0.0 800.0 °C
0.0 200.0 °C
0.0 100.0
0.0 100.0
0.0 100.0
6-4. Event delay time
• If a factor which has turned event action ON disappears, the
event will not be output and delay time measurement is
aborted.
• If a factor to turn event action ON arises and delay time is
changed within the setting range of delay time, the time starting
from the occurrence of the factor to activate the event (i.e., a
total time) works as the delay time.
NOTE: If you change a measuring range code, all measuring
ranges related to data such as SV value, event set values,
PID are initialized.
NOTE: When a type code of event, remote input or analog output
is changed, all data related to it are initialized.
- 12 -