Download 6,000W Shop Heater

V 3.05
6,000W Shop
Heater
User Manual
Please read this manual before use.
8553521
V 3.05
8553521
6,000W SHOP
HEATER
SPECIFICATIONS
BTU Rating
20,472 BTU
Heating Capability
600 sq. ft.
Heat Settings
3,000/6,000W
Current Rating
25A
Voltage Rating
240V
Feature(s)
Adjustable thermostat, Hi/Low switch and
auto reset overheat protection. Adjustable tilt
and louvers to direct heat where you need it
most.
Additional Info
Powder coated steel construction
Overall Dimensions
16-3/4 x 17-3/4 x 15-3/4 in.
CUL
CUL#KKWS7.E360195
2
For technical questions call 1-800-665-8685
8553521
6,000W Shop Heater
V 3.05
IMPORTANT INSTRUCTIONS
PLEASE READ ALL INSTRUCTIONS BEFORE USING THIS HEATER
NOTE: There may be a trace of smoke or odor when unit is first operated.
Don’t be alarmed. This indicates that a drop of oil fell on the heating coil
during the manufacturing process. It will quickly evaporate and should
not re-occur.
Make sure that the room in which the appliance is located is well
ventilated during this operation. It is normal for the appliance to emit
small cracking sounds when you turn it on for the first time. Do not be
alarmed.
WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED TO REDUCE RISK OF FIRE,
ELECTRICAL SHOCK AND INJURY TO PERSONS OR PROPERTY,
INCLUDING THE FOLLOWING:
Read all instructions before using this heater.
2) This heater is hot when in use. To avoid burns, do not let bare skin
touch hot surfaces. Keep combustible materials, such as furniture,
pillows, bedding, papers, clothes, and curtains at least 3 ft. (0.9 m)
from the front of the heater and keep them away from the sides
and rear.
3) Extreme caution is necessary when any heater is used by or near
children or invalids and whenever the heater is left operating and
unattended.
4) Always switch off the heater when not in use.
5) Do not operate any heater after the heater malfunctions, has been
dropped or damaged in any manner. Disconnect power at service
panel and have heater inspected by a reputable electrician before
reusing.
6) Do not use outdoors.
7) To disconnect heater, turn off power to heater circuit at main
disconnect panel.
8) Do not install less than 8 feet (2.4m) high from the floor and closer
than 1 foot (0.3m) to any adjacent vertical surfaces or walls. Keep
at least 4.5 inches (11.5cm) from the back wall (with or without
using the wall hanging mounting bracket).
9) Do not insert or allow foreign objects to enter any ventilation or
exhaust opening as this may cause an electric shock or fire, or
damage the heater.
Visit www.princessauto.com for more information
3
V 3.05 6,000W Shop Heater
8553521
10)To prevent a possible fire, do not block air intakes or exhaust in any
manner.
11) A heater has hot and arcing or sparking parts inside. To reduce
the risk of fire, Do not use it in areas where gasoline, paint, or
flammable vapors and liquids are used or stored.
12) Use this heater only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock,
or injury to persons.
13) This product must be installed by a certified electrician, in
accordance with local codes.
14) For supply cables, use 10 AWG (5.3 mm2) copper wires .
15) This heater includes a visual alarm to warn that parts of the heater
are getting excessively hot. If the alarm flashes, immediately turn
the heater OFF and inspect for any objects, on or adjacent to the
heater that may cause high temperatures. DO NOT OPERATE THE
HEATER WITH THE ALARM FLASHING. To reset the heater, switch
the CIRCUIT BREAKER OFF, and wait five to ten minutes for the
unit to cool down before turning the heater on.
CAUTION – High temperature, risk of fire, keep electrical cords, drapery,
furnishings, and other combustibles at least 3 feet (0.9 m) from the front
of the heater and away from the side and rear.
4
For technical questions call 1-800-665-8685
8553521
6,000W Shop Heater
V 3.05
SAVE THESE INSTRUCTIONS
WALL / CEILING MOUNT HEATER
Model : PH-960
Volt: 240 V
Watts: 6000 W
Frequency: 60 Hz
BTU/h: 20472
WIRING DIAGRAM:
Visit www.princessauto.com for more information
5
V 3.05 6,000W Shop Heater
8553521
A) Upper Enclosure
B) Tilt adjustable knob
C) Front Exhaust Grill
D) Louver for air direction
E) Control panel
F) Power Indicator
G) Alarm LED
H) Rocker Switch (High/Low select)
I) Temperature Setting Knob
WARNING: All wiring must be installed by a certified electrician
according to the electrical safety.
The ceiling heater must be grounded in accordance with all national and
local building codes.
All Wiring procedures and connections shall be in accordance with the
national and local codes having jurisdiction.
6
For technical questions call 1-800-665-8685
6,000W Shop Heater
8553521
V 3.05
BEFORE INSTALLATION:
Disconnect the main supply connection.
Supply cables shall be 10 AWG (5.3 mm2) copper wires
The heater must be connected to individual branch circuit protected by
35 Amp circuit breaker only.
Supply cables must be equipped with a dual pole circuit breaker rating
at least 240V 35A/pole as main cutoff switch of power connection to the
heater.
CAUTION : High temperature, risk of fire, keep electrical cords, drapery,
furnishings, and other combustibles at least 3 feet (0.9 m) from the front
of the heater and away from the side and rear.
WARNING: To reduce the risk of fire, do not store or use gasoline or
other flammable vapors and liquids in the vicinity of the heater.
INSTALLATION INSTRUCTION:
1. Keep the unit at least 8 feet (2.4m) away from the floor. This
minimum distance must be maintained.
2. Do not install closer than 1 foot (or 0.3 m) to any adjacent vertical
surfaces or walls.
3. Keep at least 4.5 inches (11.5cm) from the back wall (with or
without using the wall hanging mounting bracket).
4. Mark the drill-hole positions in the wall or ceiling for the mounting
bracket.
5. Drill the required holes with diameter fit for the anchor provided
for positioning the mounting bracket.
6. Insert the anchors.
7. Attach the mounting bracket to the wall or ceiling and secure with
mounting screws.
8. Hook the unit to the mounting bracket and let the unit hang from
the mounting bracket.
CEILING MOUNT
WALL MOUNT
Visit www.princessauto.com for more information
7
V 3.05 6,000W Shop Heater
8553521
9. Insert the screw through the mounting bracket and the heater
handle, tighten the nut.
10. Loosen the screw to remove the wiring compartment/connection
cover in the rear of the heater.
11. Run the electrical power supply cable in flexible conduit and
connect to the wiring compartment via the knock-out at back side
of the unit.
12. Make the connections properly with connectors which are suitable
for the conductor size, including grounding wirings. After making
the connections, arrange the pigtail leads of unit and power supply
wires in the wiring compartment.
13. Replace the wiring compartment/connection cover and lock in
place with the screw.
WARNING - The heater must be properly installed before it is used.
8
For technical questions call 1-800-665-8685
8553521
6,000W Shop Heater
V 3.05
HAZARD OF ELECTRIC SHOCK, EXPLOSION,
OR ARC FLASH :
•
•
•
Apply appropriate personal protective equipment (PPE) and follow
safe electrical work practices. See NFPA 70E.
A circuit breaker must be installed and serviced only by qualified
electrical personnel.
Always use a properly rated voltage sensing device to confirm
power is off.
The Select switch on the heater is only for function selection. Use circuit
breaker as power ON/OFF device. The circuit breaker is to be installed
by certified electrician and shall be located in line of sight from the heater
location or shall be capable of being locked in open position. Follow the
operating instruction to reduce the risk of fire, electric shock, injury or
death to persons.
•
•
Switch on the circuit breaker to turn on the heater.
Then turn the thermostat to the farthest clockwise position. The
fan should start and the unit begins heating the room, and lamp
is light. After the room reaches comfort level, turn the thermostat
counterclockwise until the heater shuts off. The heater will
automatically cycle around this preset temperature. To increase
the temperature, turn the thermostat knob clockwise. To lower the
temperature, turn the thermostat counterclockwise.
• Press the switch to High or Low position for heat selection.
HIGH : 6000W
LOW : 3000W
• Select a thermostat setting.
• Ambient temperature is regulated by adjusting the thermostat
to a desired position. Allow the unit to operate and warm up the
room. When the desired temperature is reached, turn the control
knob counterclockwise until the heater turns off. This is your
ideal setting. The heater will start automatically when the room
temperature drops below this set point, and will turn off when the
set point is reached.
• To turn off the heater, switch off the circuit breaker. The circuit
breaker serves as the power disconnection means.
• This heater includes a visual alarm to warn that parts of the heater
are getting excessively hot. If the alarm flashes, immediately turn the
Visit www.princessauto.com for more information
9
V 3.05 6,000W Shop Heater
8553521
heater OFF and inspect for any objects, on or adjacent to the heater
that may cause high temperatures. DO NOT OPERATE THE HEATER
WITH THE ALARM FLASHING. To reset the heater, switch the circuit
breaker OFF, and wait five to ten minutes for the unit to cool down
before turning the heater on.
There is no user maintenance part except regular cleaning as following
description. All other servicing or maintenance should be performed by
qualified service personnel.
Before any cleaning, make sure that:
1. Disconnect power supply at source. Switch off the circuit breaker.
2. Wait for 60 minutes to ensure the heating element has cool down,
and your heater is now ready for cleaning.
There is no user maintenance part except regular cleaning as following
description. All other servicing or maintenance should be performed by
qualified service personnel.
Before any cleaning, make sure that:
1. Disconnect power supply at source. Switch off the circuit breaker.
2. Wait for 60 minutes to ensure the heating element has cool down,
and your heater is now ready for cleaning.
Regular Cleaning:
1. Do not use cleaning liquid or other chemicals to spray on the unit.
2. Interior dust can often be removed by using a vacuum cleaner with
a crevice tool attachment.
3. To clean enclosure, use a clean, soft and lightly damp cloth to
gently wipe off the dirt from the surface of the unit. Be sure not
to wet the heating element and the switches. Allow the unit to dry
completely before using it.
CAUTION: DO NOT ALLOW WATER TO RUN INTO THE INTERIOR OF
THE HEATER AS THIS COULD CREATE A FIRE OR ELECTRIC SHOCK
HAZARD, DAMAGING THE UNIT.
If your heater fails to operate, please follow these procedures:
This heater is intended to be a ceiling-mounted heater. It has a thermal
cut-off protection. If the thermal cut-off protection trips, then, switch
10
For technical questions call 1-800-665-8685
8553521
6,000W Shop Heater
V 3.05
off the power. Switch off the circuit breaker. The unit should reset
automatically after 10 minutes. If the thermal cut-off protection trips
again, consult a certified electrician to determine the reason for
overheating.
Problem
Probable Cause
Unit is not
heating.
Overheat protection has
temporarily deactivated
the heater.
Turn the heater OFF; Switch
off the circuit breaker. Wait 10
minutes before turning on
the heater
Room temperature has
been warmed up to
thermostat setting.
To increase the room
temperature, adjust thermostat
control knob to a higher setting
Breaker/Fuse has been tripped.
Check your electrical box to
confirm the breaker has not
been blown. This may occur if the
receptacle is shared
between other high
consumption appliances.
Check & ensure there are no
combustible materials within
0.9 meters (3 feet) surrounding
the heater.
Remove any combustible items
from the heater.
A drop of oil fell on the heating
coil during the manufacturing
process. It will quickly
evaporate and should not
occur again.
Ensure room in which heater is
situated is well ventilated.
Ensure a minimum clearance of
36 inches (90 cm) from both
sides and rear of heater to
adjacent walls.
Reposition the heater so there is
enough space around the heater
to the adjacent walls.
The
heater is
producing
a burning
smell.
Solution
PLEASE DO NOT ATTEMPT TO OPEN OR REPAIR THE HEATER
YOURSELF. DOING SO COULD CAUSE DAMAGE OR PERSONAL INJURY.
Visit www.princessauto.com for more information
11