Download User`s Manual

User’s Manual
For
GeForce4 MX Series
DOC NO : 54-0NV18-01
02/09/03
Rev.A
FCC Requirement
This device has been certified to comply with the limits for a Class B computing device pursuant to Subpart J of Part 15 of
the FCC Rules. See instructions if interference to radio reception is suspected.
WARNING:
This equipment generates and uses radio frequency energy and, if not installed or used properly,
that is, in strict accordance with the manufacturer's instructions, may cause interference to radio or
television reception.
It has been tested and found to comply with the limits for a Class B compliant device in accordance with the specifications
in Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a
residential installation.
However, there is no guarantee that interference-will not occur in a particular installation.
If this equipment does cause interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
˙
˙
˙
˙
Reorient the receiving antenna
Relocate the computer away from the receiver
Move the computer away from the receiver
Plug the computer into a different outlet so that the computer and the receiver are on different branch
circuits
˙ Ensure that the card's mounting screws, attachment connector screws, and ground wires are tightly
secured
˙ Ensure that slot covers are installed in all unused slots
If necessary, consult your dealer, service representative, or an experienced radio/television Technician for additional
suggestions.
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this
equipment. It is the responsibility of the user to correct such interference.
The user may find the following booklet prepared by the Federal Communications Commission helpful:
How to Identify and Resolve Radio-TV Interference Problems.
This booklet is available from the Government Printing Office, Washington, D.C. 20402, Stock No. 004-000-00345-4.
NOTE:
CAUTION:
You must use shielded interface cables with a ferrite bead in order to maintain compliance
with the limits for a Class B device.
CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY
RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO
OPERATE THE EQUIPMENT
I
Notice
The information in this document is subject to change in order to improve reliability, design, or function
without prior notice and does not represent a commitment on the part of this company.
In no event will we be liable for direct, indirect, special, incidental, or consequential damages arising out
of the use or the inability to use the product or documentation, even if advised of the possibility of such
damages.
No part of this reference manual may be reproduced or transmitted in any form or by any means without
the prior written permission of this company.
2002
Trademark Acknowledgements
All brand names and trademarks are the property of their owners.
Limited Warranty
Our company warrants this product against defects in materials and workmanship for a period of one (1)
year from the date of purchase. During the warranty period, a product determined by us to be defective in
form or function will be repaired or at our option, to be replaced at no charge. This warranty does not
apply if the product has been damaged by accident, abuse, misuse, or as a result of service or
modification other than by us.
This warranty is in lieu of any other warranty expressed or implied. In no event shall we be held liable for
incidental or consequential damages, such as lost revenue or lost business opportunities arising from the
purchase of a this product.
Macrovision Corporation Product Notice
This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation, and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and
is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation, Reverse engineering or disassembly is prohibited.
II
TABLE OF CONTENTS
1.
1.1
1.2
1.3
2.
2.1
2.2
3.
3.1
3.2
3.3
3.4
4.
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
5.
5.1
6.
Introduction........................................................................................................ 1
Feature............................................................................................................. 1
System Requirements ...................................................................................... 2
Package Contents ............................................................................................ 2
Hardware Installation........................................................................................ 3
Adapter Configuration..................................................................................... 3
Installing your VGA adapter ........................................................................... 5
Software Installation.......................................................................................... 6
Installing driver on Windows 98SE/ME.......................................................... 6
Installing driver on Windows 2000/XP ........................................................... 6
Installing DirectX on Windows 98SE/ME/2000/XP ....................................... 7
View User's manual ......................................................................................... 7
Optional Functions............................................................................................. 8
nView Function instructions............................................................................ 8
TV-OUT Function Instructions ....................................................................... 9
How to change output to Digital Flat Panel?................................................. 12
Installing Capture Driver (Optional for Video-In)......................................... 13
Color Correction Panel.................................................................................. 15
Video Mirror Function................................................................................... 16
Desktop Utilities............................................................................................ 17
What is nView Desktop Manager? ................................................................ 18
Display Information ......................................................................................... 25
Resolutions Supported................................................................................... 25
FAQ ................................................................................................................... 26
III
1. Introduction
The NVIDIA graphics-processing unit (GPU) shakes up the gaming industry with
unprecedented visual effects and sizzling frame rates—injecting life into the
previously artificial world of computer-generated graphics. Powered by the new
NVIDIA new nfiniteFXTM engine and the Lightspeed Memory ArchitectureTM, the
GPU enables users to look into a rich environment instead of just a computer screen.
3D scenes have ambiance with the GPU because textures appear photo-realistic and
custom lighting heightens the drama. Characters and living creatures have organic
imperfections and unique expressions—you can see their personality.
Programmability and performance combine to provide the catalyst for this graphics
revolution.
NVIDIA's patented High-Resolution Antialiasing (HRAA) generates highperformance samples at nearly four times the rate of new graphics, while delivering
the industry's best visual quality. The GPU delivers more than 960 billion operations
(BOPS)—more than twice the raw performance available to consumers in today's
GPUs. For more complex scenes and visuals, the new GPU advantage grows to as
much as a seven-fold increase in delivered performance.
1.1 Feature
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
□
AGP 3.0 support for 8X and 4X and AGP 2.0 support for 4X, 2X, 1X.
New nfiniteFX™ Engine for full programmability.
256-bit 3D and 2D graphics accelerator.
512K/1M Flash-ROM on board.
Integrated hardware transform engine.
Increases memory bandwidth efficiency for unmatched performance.
Accuview Antialiasing™ technology.
Full-compliant professional OpenGL 1.3 support. For Windows Operating system
Drivers for Windows NT/9X/ME/2000/XP.
MPEG-2 hardware decode, including Inverse Discrete Cosine Transform (IDCT)
and motion compensation.
DirectX and S3TC texture compression.
Integrated second-generation transform and lighting (T&L) engines
300 MHz pixel clock supports HDTV resolutions, such as 1920 x 1080 x 60 Hz or
1280 x 720 x 60 Hz.
Integrated NTSC/PAL TV encoder supporting resolutions up to 1024 X 768.
Integrated Transition Minimized Differential Signaling (TMDS) transmitter for
Digital Visual Interface (DVI) support with scaling and filtering for flat panels up
to 1280 X 1024.
DVD-ready and HDTV-ready MPEG-2 decoding up to 1920 X 1080i Advanced
Television System Committee (ATSC) format.
1
1.2 System Requirements
□ Any motherboard with AGP bus.
□ Microsoft Windows 98SE / ME / 2000 / XP.
□ DirectX 8 or higher and OpenGL Features.
1.3 Package Contents
□
□
□
□
□
□
VGA board.
Auto-Run Driver CD.
User’s Manual.
RCA Cable 1.8m. (For TV-OUT)
S-Video to RCA cable. (For TV-OUT)
1 to 3 cables. (For Video-In/Out)
2
2. Hardware Installation
2.1 Adapter Configuration
VGA Card Specification
VGA Card Specification
3
Low-Profile VGA Card Specification
Low-Profile VGA Card Specification
4
2.2 Installing your VGA adapter
1. Power off your computer, remove its outside cover, and then assert yourself by
touching the power supply of your computer.
Note: Before installing your new VGA card, you must first set the VGA
option to either Standard VGA or Standard Display VGA.
2. Remove your old graphics card, and install your new VGA card into the AGP
slot.
PCI series product
AGP series product
AGP Slot
PCI slot
PCI slot
AGP mainboard
AGP mainboard
3. Align and secure the mounting bracket of your new VGA card to your computer
and replace your computer cover.
4. Connect your monitor cable to the DB-15 connector at your new VGA card.
!!! Caution !!!
Turn Off
Before you turn on your system,
you have to be sure the VGA card
is setup already and all the cables
are connected.
Turn Off
DO NOT connect / disconnect
TV-out cable when your TV or
PC is Power On.
5. Power on your computer.
5
3. Software Installation
After inserting VGA card into port, please turn on PC and new hardware will be
automatically detected.
Notice :
Auto-Run CD will auto-detect your VGA and TV card devices. Therefore,
it might show more than one device in the first installing window.
Otherwise, Auto-Run CD will skip the first installing window when it
only detects one device. Please select one installation of the devices that
is proper for this product.
3.1 Installing driver on Windows 98SE/ME
Please set the VGA card as “Standard PCI Graphics Adapter (VGA)”. When it
done, Windows system will ask you to restart it, please choose “No”. Then you
should follow the next step.
1. Insert the AutoRun CD-ROM driver (wait a few seconds). You will see “VGA
Installer” window that will be shown on the screen. If it does not display, please
brow CD and double click “AutoRun.exe”.
2. Click-on “Install Driver” to install the VGA driver.
3. After the installation is complete, the system will ask you whether you want to
restart your computer now. Click “Yes”, to reboot your system and activate the
program.
3.2 Installing driver on Windows 2000/XP
Please set the VGA card as “Video Controller (VGA Compatible)”. When it done,
Windows system will ask you to restart it, please choose “No”. Then you should
follow the next step.
1. Insert the AutoRun CD-ROM driver (wait a few seconds). You will see “VGA
Installer” window that will be shown on the screen. If it does not display, please
brow CD and double click “AutoRun.exe”.
2. Click “Install Driver” to install the VGA driver.
3. If you see the “Digital Signature Not Found” this dialog box please click “Yes”.
4. When asked if you want to restart your PC, click “OK” to finish the installation
and reboot your Windows.
6
3.3 Installing DirectX on Windows 98SE/ME/2000/XP
When the system restart after finishing VGA driver setup, please install better
DirectX version than that on your system.
1. Double click CD-ROM icon to let it AutoRun. The “VGA Installer” will be
shown again.
2. Click “Install DirectX” and you will see a “Installer” dialog, and click “OK” to
show next page.
3. Click “Yes” to continue.
4. Click-on “ReInstall DirectX” to install the DirectX program.
5. When it is done, please click “OK” to reboot windows.
3.4 View User's manual
Click “User’s Manual” to view detailed information regarding the various
Drivers/Programs and FAQ located on the CD.
7
4. Optional Functions
Following of functions are optional. This product may not support
Notice : those functions. Therefore, please check out the features of this
product first which are on the paper user’s manual.
4.1 nView Function instructions
4.1.1. Clone mode
1. A. You can click “Clone” to add second
device Output of clone.
B. Click “OK” or “Apply” to switch your
display mode.
2. Windows will ask you to keep your setting.
Please click “Yes” to finish switching.
8
4.2 TV-OUT Function Instructions
4.2.1. How to enable the TV-OUT function
The VGA card needs to see real 75 ohms AV input. Connect the
signal cable between TV-OUT of VGA and TV's Video input and
Warning:
turns on the TV before launch “Display Properties”. Otherwise
the TV-out function would be gray and un-selectable.
1. Set the correct jumper at your VGA card for TV formats (PAL BG/NTSC….).
2. Boot-up the system from monitor.
3. To Connect the signal cable between TV-OUT of VGA and TV’s Video input and
turn on the TV.
4. After launch “display properties” then:
A. Select “Settings” tab
B. Click “Advanced…”
C. Select “nView” tab
D. Select “Device Setting”
E. Select “Select Output
Device”
F. Click “Advanced….”
9
4.2.2. How to use TV-out cables correctly?
1.
Power off your PC and TV first.
2. Connect the signal cable to the Video input at your TV from your VGA card, and
then power on your PC and TV.
Caution: Before you power on your
system, you have to be sure the VGA
card is setup correctly and all the
cables are connected.
DO NOT connect / disconnect TV-out
cable when your TV or PC is Power
On.
4.2.3. How to change TV setting?
1. You can click “TV” to switch VGA output
to TV.
A. Click “Change Format” to select which
standard TV you want.
When you select “Make this format the
power-up default”; the System will
change BIOS default to the format, when
you boot-up next time.
10
Turn Off
Turn Off
B. Click “Video output format” to select
output from Composite or S-Video.
C. Click “OK” to switch your display
mode.
D. Click “Yes” to confirm desktop setting.
4.2.4. How to adjustment screen position?
1. Click on “Display” of Control Panel. Select
“Device Selection” tabs and click “Device
Adjustments”. You will see the windows.
A. When the output of your VGA is set to
Monitor, You can click “Device Setting”
to adjust the screen position.
WARNING:
The Monitor display may become
scrambled if you adjust the screen
position over the required range.
11
4.3 How to change output to Digital Flat Panel?
1. A. You can click “Digital Flat Panel” to
switch VGA output to Digital Flat Panel.
B. Click “OK” or “Apply” to switch your
display device.
2. Click “OK” to make sure.
3. Windows will ask you to keep this setting.
Click “Yes” to finish setting.
Note : The function is just for output device with DVI connector.
12
4.4 Installing Capture Driver (Optional for Video-In)
If your VGA board support video in you can select “install capture driver”.
4.4.1. Capture Tool
Execute “AMCAP.EXE”.
4.4.2. Capture Setting
1. File
A. Set Capture File
Click–on to set the filename of the
captured video file.
B. Allocate File Space
Click–on to set the capture file size, in
MB.
C. Save Captured Video As
Click–on to save A.AVI file using a
different filename.
13
2. Options
A. Preview
Click –on preview to start.
B. Audio Format
Click–on
to
select
the
AVI
audio-sampling format that is installed in
your system.
C. Video Capture Filter
Video decode to set the optional “Video
Proc Amp” you can change the
Brightness, Contrast, Saturation or Hue by
using the various scroll bars and viewing
the effect on your video monitor.
D. Video Capture Pin
This function is to change the video image size.
E. Video Crossbar
This function is to select the “Video Input Source”: “Video S-Video In”,
“Video TV Tuner (Optional)” or “Video Composite In”.
F. TV Tuner (This function is only for product with Tuner)
This function is to select the channel what you want to watch.
3. Capture
A. Start Capture
This function is to start capture.
B. Capture Audio
Selecting the item is to let you to capture
with audio.
C. Master Stream
You can choose master stream between
“None”, “Video” and “Audio”.
D. Set Frame Rate
This function is to set frame rate.
E. Set Time Limit
This function is to set capture time.
14
4.5 Color Correction Panel
4.5.1. Color Correction Settings
If you are using a GeForceX GPU-based card, another non-nView nVIDIA
GPU-based card, or have not enabled nView on your system yet, follow these
steps:
!"
Right click from the Windows desktop to display the context menu, click
Properties, the Settings tab, and the Advanced button.
!"
Click the Color Correction tab to display the nVIDIA Color Correction panel.
If you are using a nView-based card, have nView enabled, and want to access
the Color Control Panel from the nView panel, follow these steps:
!"
Open the nView control panel.
!"
To access the context menu, right click on a monitor icon that appears on the
nView panel.
Select Color Correction from the context menu.
!"
1. Open Color Correction
A. Active Color Channel: Allows you
to select the color channel controlled
by the sliders. You can adjust the
red, green or blue channels
individually or all three channels at
once.
B. Brightness, Contrast, and Gamma
Controls: The slider controls allow
you to adjust the brightness, contrast,
or gamma values for the selected
color channel.
C. Diagonal Line/Curve: A graphical representation of the color curve. This
curve will change in real time as you adjust the contrast, brightness or
gamma.
D. Selecting Automatically apply these settings at startup automatically
restores the color adjustments you have made here when Windows is
restarted.
2. Note: If your computer is running on a network, the color will be adjusted
after you have logged on to Windows.
15
4.6 Video Mirror Function
4.6.1. Video Mirror mode
Video Mirror is a nView feature that allows a video or DVD application to mirror
its playback in full-screen mode on any one of the connected display devices.
For Video Mirror functionality, set your nView panel to one of these modes:
•Windows XP/2000 Clone or Windows XP DualView.
•Windows 9X/ME Clone or Extended Desktop.
1. Open the DVD or video application that you want to view.
2. A. Enable Overlay Controls
B. Enable video overlay zoom: Click
this check box and click Apply to
use the Zoom control slider to zoom
in (out) on a specific area of the
video output (overlay) on your
screen. Using the diagram of the
screen regions shown on the Overlay
Controls panel, you can select the
area of the video screen you would
like to zoom. Once selected, you can
zoom to that portion of the screen by
moving the Zoom Control slider
between the Out and In range.
3. Be sure to click Apply whenever you make any changes to the control panels.
If changes do not take effect (the controls have no effect on the video) after
you click Apply, close the video overlay and then re-open it.
16
4.7 Desktop Utilities
Use the nVIDIA Desktop Utilities control panel to enable the nVIDIA
QuickTweak icon (a Windows task bar utility), which lets you conveniently view
and even modify various features and configurations that are available on the
NVIDIA control panels.
4.7.1. Desktop Utilities Control
1. The following configurations can be accessed and modified through the
QuickTweak icon:
A. 3D Antialiasing Settings: These settings are also available through the
nVIDIA 3D Antialiasing Settings control panel.
B. Custom OpenGL Setting These settings are also available through the
nVIDIA OpenGL Settings control panel.
C. Custom Direct3D Settings These settings are also available through the
nVIDIA Direct3D Settings control panel.
D. Custom Color Settings These settings are also available through the
nVIDIA Color Correction control panel.
E. Desktop Manager Settings These settings are also available by click the
title bar of an application that has already been configured with nVIDIA
Desktop Manager.
F. Adjust Display Properties These settings are also available by
right-clicking from the Windows desktop, selecting Properties and then
the Settings tab.
4.7.2. Enabling the nVIDIA QuickTweak Icon
1. Check the Display the QuickTweak
icon in the taskbar check box as
shown in window.
2. Notice that the nVIDIA icon is added to
your Windows task bar --- usually
positioned at the bottom of your
Windows desktop.
17
4.8 What is nView Desktop Manager?
nView Desktop Manager is a user level application utility that focuses on making
you more productive when working on your Windows desktop. Desktop
Management was originally created for multiple-display graphics cards but has
grown to enhance single-monitor user desktops as well.
4.8.1. Benefits of Using Profiles
Using profiles features, you can tailor
different Desktop Manager modes to
more closely match your operating needs
and then easily switch between profiles
with a hot key. You can use profiles to
quickly
switch
your
system
configuration, depending on your needs.
1. Loading a Profile
You can select a profile from the list and
select Load Profile to load the profile.
2. Creating a Profile
The New Profile allows you to create,
name, and add a new profile that contains
all of the current nView settings. Once
saved, you can reload this profile at any
time.
3. Saving a Profile
The Save Profile option lets you overwrite the existing selected profile with
your current nView settings.
4. Enabling and Disabling Desktop Manager
The Enable nView and Disable nView options are toggles to enable or
disable the nView Desktop Manager.
5. Starting the Desktop Manager Setup Wizard
Click the Wizard option to start the Desktop Manager Setup Wizard. For
details on using the Wizard.
18
4.8.2. Summary of Windows Settings
1. Window Controls
A. Enable Window Spanning Across
Monitors
This options allows windows to span
(display) across monitors. When the
option is disabled, all windows are
prevented from spanning across
monitors.
Default: Option is disabled.
B. Enable child window spanning across
monitors
To access this option, you must first
enable the “Enable child window
spanning across monitors” option.
Default: Option is disabled. This
means that child windows cannot span
monitors even if the parent window
does.
C. Show full-desktop maximize option on title bar
To access this option, you must first enable the “Enable child window
spanning across monitors” option.
When you check this option, the nView window maximize button is added
to title bars on all application windows.
2. Dialog Box Controls
A. Enable Dialog Box Repositioning
This option lets you specify the location of dialog boxes.
Default: Option is enabled.
B. Show dialog boxes on monitor n
This option repositions dialog boxes to a specific monitor, where n is the
monitor number.
C. Show dialog boxes at cursor
This option repositions dialog boxes to the monitor on which the cursor is
located.
19
D. Show dialog boxes on application’s monitor
This option repositions dialog boxes centered on the parent application’s
monitor.
3. User Interface Control
You can access Desktop Manager features quickly and easily from any
application using the nView system menu extension. Every window has a
system menu for basic tasks such as moving or resizing the window. Desktop
Manager extends this menu to add features such as making the window
transparent or moving the window to another monitor or desktop.
4.8.2. About Effects
1. Window Drawing Enhancements
A. Make Windows Maximize Faster
This option accelerates Open,
Maximize, and Restore window
functions.
B. Make Windows Transparent When
Dragged
This option enables window
transparency when windows are
dragged.
Windows become transparent as you
hold down the mouse option while on
the window’s title bar, allowing you
to quickly see what is underneath the
window.
When you release the mouse option,
the window becomes opaque.
Notes:
!"
Transparency is only supported on Windows 2000/XP.
!"
Transparency can take a lot of processing power. If Desktop Manager
detects that your system may be sluggish when dragging large
transparent windows, you will be given an option to disable transparent
window dragging for windows larger than a certain size.
!"
Transparency is disabled when a 3D application is running.
!"
Some applications do not support transparency, in which case, an
“About this app . . .” menu choice is added to the nView Extension
menu for that application.
20
2. Zoom Settings
!"
If you are using an nVIDIA dual-display GPU-based graphics card, you
have several zoom options available.
!"
If you just want a Windows tool that lets you zoom certain areas of the
desktop in a window, use the “Zoom Window” tool described in this
section.
!"
If you plan on always working with a single monitor and want a
dedicated zoom window available, it is recommended that you use the
nView Clone mode described in the nView Display Manager User’s
Guide. You can set up your system to run in nView “Clone” mode
where your second display is dedicated to being a zoomed version of
your primary display.
4.8.3. About Hot Keys
The Hot Key features can be used by both single-monitor and multiple-display
users.
1. Selecting an Action
A. Open nView control panel
Opens the Desktop Manager control
panel.
B. Run application…
Runs a user-specified application.
Note that after selection, a browse
file dialog appears where you can
select the program file you want to
run.
C. Locate cursor
Highlights the area around the cursor
allowing it to be located on the
desktop.
D. Gather all to Mon1
Move all open windows and dialog boxes on your system to monitor 1 of
the default desktop.
E. Toggle zoom window
Shows and hides the zoom window.
F. Load profile…
Loads a saved profile.
21
G. Move window to monitor…
Moves the active window to a user-specified monitor.
H. Move window to desktop…
Moves the active window to a user-specified desktop.
I. Max/Restore window
Toggles a maximize/restore function on the active window.
J. Toggle transparency
Toggles the active window between being transparent or opaque.
K. Toggle always on top
Toggles the active window between being always on top or not being on
top.
L. Show on all desktops
Toggles the active window between showing on all desktops or on a
single desktop.
M. Collapse to desktop
Causes the active window to show on the current desktop only.
N. Activate desktop…
Switches the display to a user-specified desktop.
O. Next desktop
Switches the display to the next desktop.
P. Previous desktop
Switches the display to the previous desktop.
2. Adding a Hot Key
When you click Add, the selected hot key action and keystroke combination
to the Active Hot Key list. Once a hot key is added, it is active and available
for use.
3. Removing a Hot Key
The Remove option removes the selected hot key from the list of active hot
keys. Once a hot key is removed, it is no longer active or available for use.
4. Removing All Hot Keys
The Remove all option removes all hot keys from the Active Hot Key list.
Once the hot keys are removed, they are no longer active or available for use.
22
4.8.4. About Desktops
You can use the Desktop Manager “Desktops” page to create and configure
up to 32 different “ virtual ” desktops whether you are using a single monitor
or multiple monitors.
1. Desktops setting
If you are using a single monitor, you can
create a lot of space by distributing one
of more applications among different
desktops to prevent application clutter on
your window. Desktop Manager reduces
your desktop clutter by letting you easily
move applications to other desktops thus
avoiding the need to open/close or
minimize/maximize applications in order
to navigate between them. So, window
clutter is reduced without compromising
performance or using extra keystrokes.
2. Show taskbar Quick Tweak Icon
Click the Show taskbar QuickTweak icon option on the “Desktops” page
and click Apply. This adds the nVIDIA QuickTweak icon to the Windows
taskbar.
3. Show Desktops in Explorer Window folder tree
The Show desktops in Explorer window folder tree option lets you view
desktops in the Windows Explorer folder tree.
23
4.8.5. How to over clock
Increasing the hardware clock frequencies beyond the
Warning: manufacturer’s recommended setting may cause system instability
and possibly damage the hardware.
1. Setting Hardware Options Function
Choose “Hardware Options” in
“Additional Properties” then enable
“Allow clock frequency adjustments”.
2. Please restart computer .To click
“Restart Now”.
3. After restart computer, please set the clock of “Core clock frequency” or
“Memory clock frequency” that you want in step 1.
4. Clicking “test new settings” after finish adjust clock to check it can
affordable or not.
5. To click “Apply” to finish the procedure
and you will see this message.
24
5. Display Information
5.1 Resolutions Supported
Resolutions Color Depth Refresh Rate (Hz)
640 x 480
800 X 600
1024 X 768
1152 X 864
1280 X 960
1280 X 1024
1600 X 1200
1920 X 1080
1920 X 1200
1920 X 1440
2048 X 1536
8bit
16bit
32bit
8bit
16bit
32bit
8bit
16bit
32bit
8bit
16bit
32bit
8bit
16bit
32bit
8bit
16bit
32bit
8bit
16bit
32bit
8bit
16bit
32bit
8bit
16bit
32bit
8bit
16bit
32bit
8bit
16bit
32bit
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
75
72
72
25
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
85
75
75
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
85
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
140
144
144
144
144
144
144
144
144
144
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
170
170
170
170
170
170
170
170
170
170
170
170
170
200
200
200
200
200
200
200
200
200
240
240
240
240
240
240
6. FAQ
Q: While installing on my PC, my computer loses the Vertical Sync.
A: Please check your monitor’s specifications. Some monitors connect the DDC
signal to ground: Which causes the BIOS not to detect your monitor. Therefore,
causing your VGA card not to receive any data or refresh rates.
Q: The image on my monitor keeps on flickering and the driver can't
change the refresh-rate.
A: The problem is due to a failed DDC monitor detection.
To fix the problem:
1. Chick the right button of mouse in desktop them choose ‘Properties’.
2. Select “Settings” page
3. Click “Advanced Properties”
4. Select “Monitor” page
5. Select “Change”
6. Select “Show All Devices” and choose your monitor type. If your monitor
type is not listed, please select one that is similar as possible.
Q: How do I change the resolution, color, and refresh-rate on my
Windows system?
A: Open the “My Computer” folder and select the “Control Panel” icon.
Double-click on “Display” then select “Settings”. A new menu will appear,
choose “Color Palette colors” to change the color values. Adjusting “Desktop
area” to change the Resolution (screen image size). From the same screen
click-on “Advanced Properties” to access the Refresh-rate.
Q: I can't get my system to work with AGP8X. It only can work in AGP4X.
A: 1. You must enable AGP in 8X mode in BIOS of motherboard.
2. You need to confirm motherboard have support AGP 8X mode.
3. You also need to enable AGP in 8X mode by install Motherboard chipset
driver.
26
Q: TV-OUT is grayed out on my TV-OUT capable. How can I fix it?
A: 1. The VGA card needs to see real 75 ohms AV input. However, not all TVs
have this, and some have a switch labeled “Terminate” next to the AV inputs
to turn the 75 ohms off to allow more than one TV to be connected. If you are
having this problem, especially with a smaller or portable TV, then try another
TV to see if this is a problem, or check for a “Terminate” switch.
2. According to motherboard vendor this may also be a problem caused by
motherboards using a linear voltage regulator that does not supply enough
voltage to the VGA card, and therefore there is not enough voltage to
maintain TV-OUT.
Q: My card keeps on locking up. How can I fix it?
A: 1. Are you over clocking either VGA card or your processor? If you are, try
clocking back to normal, leaving the case lids off and under clocking and see
if it fixes the problem. If it does, you need more cooling.
2. Have you assigned an IRQ to VGA in your BIOS? If not, do so.
3. Have you got an IRQ conflict with VGA card and another card? The only
device that can have the same IRQ is the “IRQ Holder for PCI Steering”. If
so, try moving the card to another slot (in particular avoid the first PCI slot as
this frequently is forced to share an IRQ with the AGP slot) or assigning a
different IRQ to that slot in the BIOS.
4. Are you running a virus checker in the background? Try disabling it.
5. Try installing the latest AGP drivers for your motherboard chipset if you
haven't got an Intel motherboard.
6. If you have an “AGP Driving Control” setting in your BIOS, try switching it
to ‘BA’ or another value instead of “Auto”.
7. If you have a VIA chipset, try enabling AGP8X. We have chosen to disable
the AGP sideband transfer because there have been various system instability
problems due to issues in the design of some motherboards.
Q: The system will hang up when I play 3D game in win98se system.
A: 1. Start ⇒ programs⇒ accessories⇒ system tools⇒ system information
2. Tools⇒ DirectX Diagnostic Tool⇒ display
3. Disable “Direct3D Acceleration” to try.
27
Q: If I set the VGA card as the primary card in the BIOS, my secondary
PCI video card is not detected. How can I fix it?
A: Check in your C:\CONFIG.SYS file to see if you are loading EMM386.EXE. If
you are, remove the line.
Q: Games stutter with my card. How can I fix it?
A: 1. Go into the System Control Panel, click on Device Manager, and find your
CD/DVD-ROM drive(s) and hard drive(s). Go into each one, click on Settings
and tick DMA. This enables UltraDMA.
2. Make sure that Video BIOS shadowing is disabled in your BIOS.
3. Make sure that your VGA card is not sharing any IRQs with another card - the
only device that can have the same IRQ is the “IRQ Holder for PCI
Steering”. If you find that the GeForce4 Ti is sharing an IRQ, try moving the
card that it is sharing the IRQ with to another slot.
Q: I get flickering textures in Quake 3 Arena and Windows 98/98SE. How
can I fix it?
A: Type the following at the console:
˙ /r_ext_compiled_vertex_array 0
˙ /vid_restart
Q: How do I change the resolution, color, and refresh-rate on my
Windows NT system?
A: The procedure is basically the same as above, for the Windows 98SE system.
Except that you must select “Test” then “OK”, so that the changes can take
affect.
28