Download SC-PTX7 - Support
Transcript
PTX79P.book Page 62 Monday, April 9, 2007 9:24 AM Using the FM/AM radio ∫ FM frequency step HDD The step is factory-set to 0.2-MHz (200-kHz), but you can change it to receive broadcasts allocated in 0.1-MHz (100-kHz) steps. Preparation To display the picture turn on the television and select the appropriate video input to suit the connections to this unit. BAND SELECT VOLUME CANCEL STOP PAUSE FUNCTIONS TOUCH PLAY ONE RTޓޓޓ STA ޓDIRECT NAV TOP MENU IGATOR MENU PLAYLIST 1 Press [TUNER/BAND]§1 to select “FM”. 2 Press [SUB MENU]. 3 Press [3 4] to select “Select Frequency Step” and press [ENTER]. 4 Press [3 4] to select the frequency step and press [ENTER]. 5 Press [2, 1] to select “Yes” and press [ENTER]. [Note] After changing the setting, previously preset frequencies will be cleared and the timer setting of FM recording will be canceled. Preset them again. PLAY ENERGETIC MELLOW RELAXING EMOTIONAL HDDREC CH SELECT FAVORITE REG 2ND SELECT PLAYMODE FL DISPLAY SLEEP VS SETUP SOUND SELECT MUTING 10SELECTOR TUNING OPEN/CLOSE SELECTOR VOLUME To return to the previous screen Press [RETURN]. TUNING MUSIC PORT Setting preset channels Up to 30 stations can be set in each band, FM and AM. Radio operations are described mainly with the remote control. You can alternatively use the corresponding button on the main unit. §1 [O N SELECTOR] §2 [X TUNING W] Manual tuning 1 2 Press [TUNER/BAND]§1 to select “FM” or “AM”. Preparation To display the picture turn on the television and select the appropriate video input to suit the connections to this unit. 1 2 3 Press [TUNER/BAND]§1 to select “FM” or “AM”. Press [6 5] to select the frequency. Press [SUB MENU]. Press [6 5] to select the frequency. PL PRG D DTS CD MODE DVD RDS PTY PS A AC DISC SFC TG FM D.MIX MONO SLP ST CT SRD E. HDCD H.BASS W PGM RND 1 2 Erase Preset Channel 4 RQT8926 62 When “AM” is selected 1 Press [PLAY MODE]. Each time you press the button: BP1 (.BP2 (BP=Beat Proof) 2 Select “BP1” or “BP2” that receives good reception. Recording Mode LPCM Auto Track Divide Auto 5 Minutes Press [3 4] to select “Set Preset Channel” and press [ENTER]. FM Set Preset Channel CH1 CH2 CH3 CH4 CH5 ∫ If noise is excessive When “FM” is selected Preparation To display the picture turn on the television and select the appropriate video input to suit the connections to this unit. 1 Press [SUB MENU]. 2 Press [3 4] to select “Audio Mode” and press [ENTER]. 3 Press [3 4] to select “Mono” and press [ENTER]. ≥“MONO” (monaural) lights up in the display. ≥This should normally be set to “Auto(Stereo)”. Auto(Stereo) Set Preset Channel When a stereo broadcast is being received, “ST” lights in the display. ≥To start automatic tuning, press and hold [6 5] until the frequency starts scrolling. Tuning stops when a station is found. Sub Menu Audio Mode 5 88.1 MHz 88.5 MHz 88.7 MHz - - .- MHz - - .- MHz Press [3 4] to select the channel and press [ENTER]. Set Preset CH. Preset: CH4 Frequency: 89.9 MHz Repeat steps 2–5 to set other channels. To return to the previous screen Press [RETURN].