Download USER GUIDE

NF2
NETCOMM FIBRE SERIES
NF2 – DUAL BAND WIFI GIGABIT HUB
USER GUIDE
Copyright
Copyright©2012 NetComm Wireless Limited. All rights reserved.
The information contained herein is proprietary to NetComm Wireless Limited. No part of this document may be translated,
transcribed, reproduced, in any form, or by any means without prior written consent of NetComm Wireless Limited.
Please note: This document is subject to change without notice.
Save Our Environment
When this equipment has reached the end of its useful life, it must be taken to a recycling centre and processed separately from
domestic waste.
The cardboard box, the plastic contained in the packaging, and the parts that make up this device can be recycled in accordance
with regionally established regulations. Never dispose of this electronic equipment along with your household waste. You may be
subject to penalties or sanctions under the law. Instead, ask for disposal instructions from your municipal government.
Please be responsible and protect our environment.
This manual covers the following products:
NetComm NF2
DOCUMENT VERSION
1.0 - Initial document release
DATE
21/02/2011
Table 1 - Document Revision History
YML27
www.netcommlimited.com
NetComm NF2 User Guide
2
Table of Contents
Overview ........................................................................................................................................................................................ 5
Introduction ................................................................................................................................................................................................... 5
Target Users.................................................................................................................................................................................................. 5
Prerequisites.................................................................................................................................................................................................. 5
Notation ........................................................................................................................................................................................................ 5
Product Introduction ..................................................................................................................................................................... 6
Product Overview .......................................................................................................................................................................................... 6
Package Contents ......................................................................................................................................................................................... 6
Product Features ........................................................................................................................................................................................... 6
Physical Dimensions and Indicators ............................................................................................................................................ 7
LED Indicators ............................................................................................................................................................................................... 7
Integrated Interfaces ...................................................................................................................................................................................... 7
NF2 Default Settings ...................................................................................................................................................................................... 9
Safety and Product Care ............................................................................................................................................................. 10
Transport and Handling ............................................................................................................................................................... 10
Installation and Configuration of the NetComm NF2 ................................................................................................................. 11
Placement of your NF2 and Mobile Broadband ............................................................................................................................................. 11
Avoid obstacles and interference .................................................................................................................................................................. 11
Cordless Phones ......................................................................................................................................................................................... 11
Choose the “Quietest” Channel for your Wireless Network ............................................................................................................................ 11
Hardware installation.................................................................................................................................................................................... 12
Connecting via an Ethernet cable ................................................................................................................................................................. 12
Connecting wirelessly .................................................................................................................................................................................. 12
First Time Simple Configuration Wizard......................................................................................................................................................... 13
Management Console Login Procedure ........................................................................................................................................................ 18
Management Console .................................................................................................................................................................................. 19
Advanced Features ...................................................................................................................................................................................... 24
Network Setup ............................................................................................................................................................................. 25
Network Setup ............................................................................................................................................................................................ 25
DHCP ......................................................................................................................................................................................................... 27
Wireless 2.4 GHz ......................................................................................................................................................................................... 28
WDS Settings .............................................................................................................................................................................................. 29
WPS Setup ................................................................................................................................................................................................. 29
Wireless 5.0 GHz ......................................................................................................................................................................................... 30
VPN – IPSec ................................................................................................................................................................................................ 31
VPN-L2TP ................................................................................................................................................................................................... 33
VPN-PPTP Client ......................................................................................................................................................................................... 33
VPN – PPTP Server ..................................................................................................................................................................................... 34
Change Password ....................................................................................................................................................................................... 35
Forwarding Rules ......................................................................................................................................................................... 36
Virtual Server ............................................................................................................................................................................................... 36
Special AP................................................................................................................................................................................................... 37
Miscellaneous .............................................................................................................................................................................................. 37
Security Settings.......................................................................................................................................................................... 38
Status ......................................................................................................................................................................................................... 38
Packet Filtering ............................................................................................................................................................................................ 38
MAC Control ............................................................................................................................................................................................... 39
Domain Filter ............................................................................................................................................................................................... 40
URL Blocking .............................................................................................................................................................................................. 41
Miscellaneous .............................................................................................................................................................................................. 41
Advanced Settings ...................................................................................................................................................................... 42
Status ......................................................................................................................................................................................................... 42
System Log ................................................................................................................................................................................................. 42
Dynamic DNS .............................................................................................................................................................................................. 43
QoS (Quality of Service) ............................................................................................................................................................................... 44
SNMP ......................................................................................................................................................................................................... 44
Routing ....................................................................................................................................................................................................... 45
System Time ............................................................................................................................................................................................... 46
Scheduling .................................................................................................................................................................................................. 46
IPV6 ............................................................................................................................................................................................................ 48
TR-069........................................................................................................................................................................................................ 49
VLAN .......................................................................................................................................................................................................... 50
NAS Settings ................................................................................................................................................................................ 51
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
3
YML38
www.netcommlimited.com
Disk Utility ................................................................................................................................................................................................... 51
File Sharing.................................................................................................................................................................................................. 51
FTP Service Configuration ............................................................................................................................................................................ 52
Access Control ............................................................................................................................................................................................ 53
iTunes Server .............................................................................................................................................................................................. 54
Download Assistant ..................................................................................................................................................................................... 55
Download Status ......................................................................................................................................................................................... 56
Web HDD .................................................................................................................................................................................................... 57
Toolbox ........................................................................................................................................................................................ 58
System Info ................................................................................................................................................................................................. 58
Restore Settings .......................................................................................................................................................................................... 59
Firmware Upgrade ....................................................................................................................................................................................... 59
Backup Settings .......................................................................................................................................................................................... 59
Reset to Default ........................................................................................................................................................................................... 60
Reboot ........................................................................................................................................................................................................ 60
Startup Wizard............................................................................................................................................................................................. 61
Miscellaneous .............................................................................................................................................................................................. 61
Logout ........................................................................................................................................................................................................ 62
Additional Product Information ................................................................................................................................................... 63
Establishing a wireless connection................................................................................................................................................................ 63
Technical Data ............................................................................................................................................................................. 64
Electrical Specifications................................................................................................................................................................................ 64
Environmental Specifications / Tolerances .................................................................................................................................................... 64
FAQ .............................................................................................................................................................................................. 65
Appendix A: Tables...................................................................................................................................................................... 66
Legal & Regulatory Information................................................................................................................................................... 67
Intellectual Property Rights ........................................................................................................................................................................... 67
Contact......................................................................................................................................................................................... 69
YML27
www.netcommlimited.com
NetComm NF2 User Guide
4
Overview
Introduction
This manual provides information related to the installation, operation, and utilisation of the NetComm NF2.
Target Users
The individual reading this manual is presumed to have a basic understanding of telecommunications terminology and concepts.
Prerequisites
Before continuing with the installation of your NF2 Hub, please confirm that you comply with the minimum system requirements
below.

An activated fixed line Internet connection with a working modem attached (ADSL, Cable, Fibre) and/or a compatible
3G/4G USB modem.

Computer with Windows, Macintosh, or Linux-based operating systems with a working Ethernet adapter with TCP/IP
Protocol installed.

A Web Browser such as Internet Explorer, Netscape Navigator, Mozilla Firefox, Opera, Safari etc.

Wireless Computer System Requirements:
o Computer with a working 802.11b, 802.11g or 802.11n wireless adapter.
Notation
The following symbols are utilised in this user manual:
The following note requires attention
The following note provides a warning
The following note provides relevant information
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
5
YML38
www.netcommlimited.com
Product Introduction
Product Overview















1.
Wireless WAN (where network is available) - GPRS/EDGE/WCDMA/HSDPA/HSUPA/CDMA2000/EVDO/LTE.
Ethernet WAN – PPPoE, DHCP client, Static IP, PPTP, L2TP
2 x USB 2.0 ports – for 3G/4G, USB storage.
2 x 3 internal WiFi antenna
1 x external WiFi antenna
IPv6 Support – Dual Stack IPv6, Static IPv6, DHCPv6, PPPOE, 6 to 4, IPv6 to IPv4 tunnel
3 x 10/100/1000Mbps LAN Ethernet ports.
1 x 10/100/1000Mbps WAN Ethernet port for optional alternate Internet connectivity (ADSL/Cable/Satellite).
802.11n up to 900Mbps Wireless1 (Backward compatible with 802.11b/g/a).
2.4GHz and 5.0GHz Concurrent WiFi.
Supports auto Internet fallback from 3G to a fixed line WAN connection (ADSL/Cable/Satellite).
WiFi Protected Setup (WPS) for wireless connectivity.
Browser based interface for configuration and management.
Wireless security options- WEP/WPA/WPA-PSK/WPA2/WPA2-PSK.
VPN IPsec, VPN L2TPClient/Server, VPN PPTP Client/Server.
Speeds are dependent on network coverage. See your MBB provider coverage maps for more details. The total number of WiFi users can also affect data speeds.
The maximum wireless signal rate and coverage values are derived from IEEE Standard 802.11g and 802.11n specifications. The actual wireless speed and
coverage are dependent on network and environmental conditions including but not limited to the volume of network traffic, building materials and
construction/layout.
Package Contents
The NF2 Hub package consists of:







1 x NF2 WiFi Router.
1 x 12VDC~1.5A Power Adapter.
1 x External Antenna.
1 x RJ-45 LAN Cable.
Quick Setup Guide.
Wireless Security Card.
Warranty Card.
If any of these items are missing or damaged, please contact your dealer immediately.
Product Features
The NetComm NF2 creates a secure WiFi network, providing Internet access for up to 15 users. Simply plug the NF2 into a power
outlet then insert a Mobile Broadband (MBB) dongle into the USB port on the side panel to access a high speed Internet connection
within minutes.
The NetComm NF2 incorporates a WLAN 802.11b/g/n access point, three 10/100/1000Mbps Gigabit Ethernet ports and one
10/100Mbps Ethernet WAN port. It features the latest security options such as WPA and WPA2 data encryption, SPI (Stateful
Packet Inspection) Firewall and VPN pass through.
YML27
www.netcommlimited.com
NetComm NF2 User Guide
6
Physical Dimensions and
Indicators
LED Indicators
The NetComm NF2 has been designed to be placed on a desktop. All of the cables exit from the rear for better organization. The
display is visible on the front of the NF2 to provide you with information about network activity and the device status. See below for
an explanation of each of the indicator lights.
LED
INDICATOR
ICON
3G
WWW
LAN1 - 4
WiFi
Power
COLOUR
DEFINITION
Blue On
Connected via 3G/4G modem
Off
3G/4G is not configured or no dongle connected.
Blue Flashing
Connecting.
Red On
SIM Error
Red Flashing
Connection failed. Retrying.
Blue On
Connected via WAN Ethernet port.
Blue Blinking
WAN port traffic.
Red On
Connected via 3G/4G
Red Blinking
3G traffic.
Off
Internet connection not configured.
Blue On
LAN connection is established.
Blue Blinking
Traffic on Ethernet port.
Off
Ethernet link is down.
Blue On
WiFi is enabled.
Blue Flashing
WPS negotiation in process.
Blue Blinking
Traffic on the WiFi network.
Off
WiFi Disabled.
Off
Powered off.
Blue Flashing
Device is starting up.
Blue On
Powered on.
Table 2 - LED Indicators
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
7
YML38
www.netcommlimited.com
Integrated Interfaces
The following integrated interfaces are available on the rear of the NetComm NF2:
INTERFACE
WiFi Antenna
WAN
Attach the wireless antenna turning it in a clockwise direction.
The WAN Ethernet port for a Fixed Line (ADSL/Cable/Satellite) connection
to the internet.
On/Off
The power button for the NF2. Press once to switch the unit on or off.
LAN 1
The LAN 1 Port for wired Ethernet clients (Computers, Laptops, etc).
LAN 2
The LAN 2 Port for wired Ethernet clients (Computers, Laptops, etc).
LAN 3
The LAN 3 Port for wired Ethernet clients (Computers, Laptops, etc).
Power
The power connector designed for use with a DC 12V 1.5A Power
Adapter.
Reset
Hold this button down for over 10 seconds to reset the router to factory
default settings.
3G
USB Storage
YML27
www.netcommlimited.com
FUNCTION
Connect a 3G/4G USB modem here
Connect a USB based storage device here
Table 3 –
Integrated Interface
NetComm NF2 User Guide
8
NF2 Default Settings
The following tables list the default settings for the NF2 Hub.
LAN (MANAGEMENT)
Static IP Address:
192.168.20.1
Subnet Mask:
255.255.255.0
Default Gateway:
192.168.20.1
Table 3: LAN Management Default Settings
WAN (INTERNET)
WAN mode:
Dynamic IP
Table 4: WAN Port Default Settings
WIRELESS (WIFI)
SSID:
(Refer to the included wireless security card)
Security:
WPA-PSK/WPA2-PSK
Security Key:
(Refer to the included wireless security card)
Table 5: WiFi Default Settings
For security purposes, each NF2 comes with a unique SSID that varies by a 4 digit number at the end. e.g. SSID: “NetComm Wireless XXXX”
NF2™ HUB WEB INTERFACE ACCESS
Username:
Password:
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
9
admin
admin
Table 6: Web Interface Default Settings
YML38
www.netcommlimited.com
Safety and Product Care
With reference to unpacking, installation, use and maintenance of your electronic device, the following basic guidelines are
recommended:



To avoid fire or shock hazard do not use or install this product near water. For example, near a bathtub, kitchen sink,
laundry tub, or near a swimming pool. Also, do not expose the equipment to rain or damp areas (e.g. a wet basement).
Do not connect the power supply cord on elevated surfaces. Allow it to lie freely. There should be no obstructions in its
path and no heavy items should be placed on the cord. In addition, do not walk on, step on or mistreat the cord.
To safeguard the equipment against overheating, make sure that all openings in the unit that offer exposure to air are
unobstructed.
WARNING
Disconnect the power line from the device before servicing.
Transport and Handling
When transporting the NetComm NF2, it is recommended to return the product in the original packaging. This ensures the product
will not be damaged.
In the event the product needs to be returned, ensure it is securely packaged with appropriate padding to prevent
damage during courier transport.
YML27
www.netcommlimited.com
NetComm NF2 User Guide
10
Installation and Configuration of
the NetComm NF2
Placement of your NF2 and Mobile Broadband
Just like your mobile phone, the NF2’s location will affect its signal strength to the MBB (Mobile Broadband) Provider’s Mobile Base
Station (Cell Tower). The data speed achievable from the NF2 is relative to this signal strength, which is affected by many
environmental factors. Please keep in mind that the NF2 will need adequate signal strength in order to provide Internet connectivity
whilst choosing a location to place your NF2.
Similarly, the wireless connection between your NF2 and your WiFi devices will be stronger the closer your connected devices are to
your NF2. Your wireless connection and performance will degrade as the distance between your NF2 and connected devices
increases. This may or may not be directly noticeable, and is greatly affected by the individual installation environment.
If you have concerns about your network’s performance that might be related to range or obstruction factors, try moving the
computer to a position between three to five meters from the NF2™ Hub in order to see if distance is the problem.
Please note: While some of the items listed below can affect network performance, they will not prohibit your wireless
network from functioning. If you are concerned that your network is not operating at its maximum effectiveness, this
checklist may help. Please ensure that your NF2 WiFi external antenna is positioned vertically (toward the ceiling).
If you experience difficulties connecting wirelessly between your WiFi Devices and your NF2, please try the following steps:

In multi-storey homes, place the NF2 on a floor that is as close to the centre of the home as possible. This may mean
placing the NF2 on an upper floor.

Try not to place the NF2™ Hub near a cordless telephone that operates at the same radio frequency as the NF2
(2.4GHz).
Avoid obstacles and interference
Avoid placing your NF2 near devices that may emit radio “noise”, such as microwave ovens. Dense objects that can inhibit wireless
communication include:

Refrigerators.

Washers and/or dryers.

Metal cabinets.

Large aquariums.

Metallic-based, UV-tinted windows.

If your wireless signal seems weak in some spots, make sure that objects such as those listed above are not blocking
the signal’s path (between your wireless devices and the NF2).
Cordless Phones
If the performance of your wireless network is impaired after considering the above issues, and you have a cordless phone:

Try moving cordless phones away from your NF2 and your wireless-enabled computers.

Unplug and remove the battery from any cordless phone that operates on the 2.4GHz band (check manufacturer’s
information). If this fixes the problem, your phone may be interfering with the NF2.

If your phone supports channel selection, change the channel on the phone to the farthest channel from your wireless
network. For example, change the phone to channel 1 and move your NF2 to channel 11. See your phone’s user
manual for detailed instructions.

If necessary, consider switching to a 900MHz or 5GHz cordless phone.
Choose the “Quietest” Channel for your Wireless Network
In locations where homes or offices are close together, such as apartment buildings or office complexes, there may be wireless
networks nearby that can conflict with your wireless network. Use the Site Survey capabilities found in the Wireless Utility of your
wireless adapter to locate any other wireless networks that are available (see your wireless adapter’s user manual), and switch your
Router and computers to a channel as far away from other networks as possible.
Experiment with more than one of the available channels, in order to find the clearest connection and avoid interference from
neighbouring cordless phones or other wireless devices.
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
11
YML38
www.netcommlimited.com
Hardware installation
1.
2.
3.
4.
5.
Attach the supplied antenna to the antenna port. [This should be attached in a clockwise direction.]
Insert your MBB (Mobile Broadband) Dongle into the USB slot.
Connect the power adapter to the Power socket on the back of the NF2.
Plug the power adapter into the wall socket and switch on the power.
Wait approximately 60 seconds for the NF2 to power up.
Connecting via an Ethernet cable
1.
2.
3.
4.
5.
6.
7.
Connect the Ethernet cable provided to the port marked LAN at the back of the NF2.
Connect the other end of the yellow Ethernet cable to your computer.
Wait approximately 30 seconds for the connection to establish.
Open your Web browser and type http://192.168.20.1 into the address bar and press enter.
Enter “admin” (without quotations) for both the Username and Password and click on the Login button.
Follow the steps of the start-up wizard to set up your NF2.
After the setup process is completed, you will be connected to the Internet.
Connecting wirelessly
1. Ensure WiFi is enabled on your device (computer/laptop/Smartphone).
2. Scan for wireless networks in your area and connect to the network name that matches the Wireless network name found
on the Wireless Security Card (included in the box).
Figure 1: Included Security Card
Please note: For security purposes, each NF2 has a unique SSID (such as NetComm-WirelessXXXX) and Wireless Security
Key. The included Wireless Security Card lists these fields instead of the xxxxx’s as shown in the screenshot above.
3.
4.
5.
6.
7.
8.
9.
When prompted for your wireless security settings, enter the wireless security key listed on your Wireless Security Card.
Wait approximately 30 seconds for the connection to be established.
Open your Web browser and type http://192.168.20.1 into the address bar and press enter.
Enter “admin” (without quotations) as both the Username and Password and press the Login button.
Follow the steps to set up your NF2.
After the setup process is completed, you will be connected to the Internet.
To connect additional devices via WiFi, repeat steps 1 through 4.
YML27
www.netcommlimited.com
NetComm NF2 User Guide
12
First Time Simple Configuration Wizard
When you log in to your NF2 for the first time, you will be presented with the NF2 “Set-up Wizard” as shown in the screenshot
below. This wizard can be skipped by clicking on the link shown on the screenshot below. You can re-run the Setup Wizard again
anytime after first use by selecting the “Setup Wizard” option under the “Toolbox” tab in the Advanced View of the management
console.
Figure 2: Setup Wizard - Start
Figure 2: Setup Wizard Step 1 –WAN Interface
Select your WAN interface preference – Ethernet WAN, 3G or Ethernet WAN with 3G backup. The example above shows an
Ethernet WAN connection with 3G backup. Press the Next button to continue the setup wizard.
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
13
YML38
www.netcommlimited.com
Figure 3: Setup Wizard Step 2 - 2.4 GHz WiFi Setup
This page allows you to customize the 2.4GHz wireless setting of the NF2.
Wireless (WiFi):
WiFi is set to “On” by default. Changing this option to “Off” will turn off the wireless feature and you will not be able to connect to
your NF2 via 2.4 GHz WiFi.
SSID Broadcast:
Select ‘Disable’ to hide the SSID of the NF2. If disabled, other people will not be able scan and detect your NF2’s SSID.
SSID Broadcast Name (Max 32 Characters):
The SSID (Service Set Identifier) is the name of your wireless network. Use a unique name to identify your wireless network so that
you can easily connect from your wireless clients. This field is case sensitive and can be up to 32 characters. You should change
the default SSID for added security.
Click “Next” to continue.
YML27
www.netcommlimited.com
NetComm NF2 User Guide
14
Figure 4 - Setup Wizard Step 3 – 2.4 GHz WiFi Security Settings
This page allows you to configure the 2.4 GHz WiFi security settings for the NF2. Setting a strong wireless security level (such as
WPA-PSK - AES) can prevent unauthorized access to your wireless network. Please enter the Security Key that you wish to use, or
leave this field unchanged to use the default Security Key. Click “Next” to continue.
Figure 7: Setup Wizard Step 4 - 5.0 GHz WiFi Setup
This page allows you to customize the 5.0 GHz wireless setting of the NF2.
Wireless (WiFi):
WiFi is set to “On” by default. Changing this option to “Off” will turn off the wireless feature and you will not be able to connect to
your NF2 via 5.0 GHz WiFi.
SSID Broadcast:
Select ‘Disable’ to hide the SSID of the NF2. If disabled, other people will not be able scan and detect your NF2’s SSID.
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
15
YML38
www.netcommlimited.com
SSID Broadcast Name (Max 32 Characters):
The SSID (Service Set Identifier) is the name of your wireless network. Use a unique name to identify your wireless network so that
you can easily connect from your wireless clients. This field is case sensitive and can be up to 32 characters. You should change
the default SSID for added security.
Click “Next” to continue.
Figure 5: Setup Wizard Step 5 - 5.0 GHz Wireless Security Setup
This page allows you to configure the 5.0 GHz WiFi security settings for the NF2. Setting a strong wireless security level (such as
WPA-PSK - AES) can prevent unauthorized access to your wireless network. Please enter the Security Key that you wish to use, or
leave this field unchanged to use the default Security Key. Click “Next” to continue.
Figure 6: Setup Wizard Step 6 - Router Security Settings
YML27
www.netcommlimited.com
NetComm NF2 User Guide
16
In Step 6 of the NF2 Setup Wizard the administration password for the router can be set to prevent unauthorised access to the
router management page. Enter the Desired Username and Desired Password, retyping the desired Password in the Retype
Password field to confirm the new password. Click Next to continue the setup wizard.
Figure 7: Setup Wizard Step 7 - Summary
Review your settings then click “Finish” to save configuration. Click “Back” if you want to make any changes.
After clicking Finish, the NF2 will save your configuration and reboot itself. Please wait as this process takes about 2 minutes. You
will be guided back to the management console once the process is complete.
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
17
YML38
www.netcommlimited.com
Management Console Login Procedure
After first time setup, the management console will be password protected to prevent unauthorized access to the configuration
settings of your NetComm NF2.
To log in to the management console, view the status and make changes to your NF2, please follow the steps below:
1. Open your web browser (e.g. Internet Explorer/Firefox/Safari) and navigate to http://192.168.20.1
2. Enter the username and password configured during the first time setup and click the Submit button. Use the default
username and password “admin” if these details have not been customized. Click “Login” to continue.
Please note: If you forget the username and password you selected during the NF2 set-up process, holding the reset
button for over 10 seconds will restart the unit with the original settings (username: admin / password: admin).
Please note: In the event that your Internet connection becomes unavailable and no fail over service has been configured,
the NetComm NF2 Management console page will display when attempting to browse to an Internet site.
Figure 8: Management Console Login
YML27
www.netcommlimited.com
NetComm NF2 User Guide
18
Management Console
Basic Status Overview
The basic status page provides basic system related information. It can be accessed by clicking on the “Switch to Basic view”
button from the top of the status page.
Figure 9: Basic View – Status
The status page shows the current primary Internet connection, WAN/LAN status, MBB connection status, current Signal Strength
(dBm) and the SIM Status.
ITEM
DEFINITION
WAN Type
The current WAN type set on the NF2.
IP Address
The current WAN IP Address is listed here.
Subnet Mask
The current subnet mask of the NF2 is listed here.
Gateway
The current gateway of the NF2 is listed here
3G Status
The current status of the 3G connectivity is listed here.
3G Signal Strength
The current signal strength of the MBB (Mobile Broadband) service connection.
Number of Clients connected on
Wireless 2.4GHz
The current numbers of clients connected on the NF2 via 2.4GHz
Number of clients connected on
Wireless 5GHz
The current numbers of clients connected on the NF2 via 5GHz
Table 7: Basic View - Status
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
19
YML38
www.netcommlimited.com
2.4 GHz Wireless
Figure 11: Basic View – 2.4 GHz Wireless
This page allows you to configure basic 2.4 GHz WiFi settings for this device such as enabling/disabling the 2.4 GHz WiFi
functionality, changing the 2.4 GHz Wireless Network Name (SSID) or the 2.4 GHz Wireless Security key. If you make any changes
to the settings, click the “Save and apply changes” button to make these changes active.
OPTION
DEFINITION
Wireless (WiFi) ON/ OFF:
Changing this option to Off will turn off the WiFi feature on the NF2 and you will not be able to connect to your
NF2 wirelessly.
SSID Broadcast
Select whether the NF2 will broadcast the SSID (Network Name) for any wireless device in range to detect
SSID Broadcast Name (SSID):
The SSID (Service Set Identifier) is the name of your wireless network. Use a unique name to identify your
wireless device so that you can easily connect to it from your wireless clients. This field is case sensitive and
can be up to 32 characters long.
Security key:
YML27
www.netcommlimited.com
Enter your chosen Wireless Security key here. The default WPA-PSK key is printed on the wireless security
card and on the Product ID on the bottom of the NF2. Please note that whilst the key can be customized on
this page, the key will revert to the default if the NF2 is reset to factory default settings.
Table 8: Basic View - 2.4 GHz Wireless Settings
NetComm NF2 User Guide
20
5.0 GHz Wireless
Figure 10: Basic - 5.0 GHz Wireless
This page allows you to configure basic 5.0 GHz WiFi settings for this device such as enabling/disabling the 5.0 GHz WiFi
functionality, changing the 5.0 GHz Wireless Network Name (SSID) or the 5.0 GHz Wireless Security key. If you make any changes
to the settings, click the “Save and apply changes” button to make these changes active.
OPTION
DEFINITION
Wireless (WiFi) ON/ OFF:
Changing this option to Off will turn off the WiFi feature on the NF2 and you will not be able to connect to your
NF2 wirelessly.
SSID Broadcast
Select whether the NF2 will broadcast the SSID (Network Name) for any wireless device in range to detect.
WiFi Network Name (SSID):
The SSID (Service Set Identifier) is the name of your wireless network. Use a unique name to identify your
wireless device so that you can easily connect to it from your wireless clients. This field is case sensitive and
can be up to 32 characters long.
Security key:
Enter your chosen Wireless Security key here. The default WPA-PSK key is printed on the wireless security
card and on the Product ID on the bottom of the NF2. Please note that whilst the key can be customized on
this page, the key will revert to the default if the NF2 is reset to factory default settings.
Table 9: Basic View - 5.0 GHZ Wireless Settings
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
21
YML38
www.netcommlimited.com
Mobile Broadband
Figure 11: Basic View - Mobile Broadband
This page allows you to configure the MBB (Mobile Broadband) WAN connection settings for the NF2.
OPTION
DEFINITION
Country
Select the country that your MBB (Mobile Broadband) provider is situated in.
Service Provider
Select the MBB provider for your 3G/4G dongle and/or SIM card.
Network Name (APN)
Enter the Access Point Name (APN) of your MBB provider.
SIM Status
This field indicates whether the SIM card has been detected and is functioning correctly.
PIN
If the SIM card requires a PIN to operate enter the PIN into this field.
Confirm PIN
If the SIM card requires a PIN to operate enter the PIN into this field also.
Table 10: Basic View - Mobile Broadband Settings
YML27
www.netcommlimited.com
NetComm NF2 User Guide
22
WAN
Figure 12: Basic View – WAN
This page gives the user the option of selecting the WAN interface type. Options include Dynamic IP address (the default option),
Static IP Address, PPPoE, PPTP, or L2TP. There is also an option to enter a Host Name with which to access the router instead of
having to enter an IP address into a browser, which may be difficult to remember. You can also press the clone button to
automatically detect the WAN connection’s MAC address.
OPTION
DEFINITION
WAN type
The current Wide Area Network (WAN) interface type can be selected here.
Host Name
The option to set a label to the router’s IP address so that it can be accessed using the host name instead of
via an IP address.
ISP Registered MAC address
The WAN connection’s MAC address is the MAC address that the ISP will be detecting.
Enable 3G backup
Select this option if you require a Mobile Broadband WAN connection to act as a failover for the Ethernet WAN
connection. Please see the Mobile Broadband page for a description of the 3G/4G settings.
Figure 13: Basic View - WAN Settings
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
23
YML38
www.netcommlimited.com
Advanced Features
The basic configuration interface is intended to provide access to all the settings that most people will want to use on their
NetComm NF2. There are advanced settings available if desired which are accessible by viewing the advanced settings pages.
Click on the “Switch to Advanced View” option to configure the advanced features of your NF2.
Status
The status page provides system related information and is displayed when you login to the NetComm NF2 management console
and switch to the Advanced View. By default, the status page will show IPv4 System Status, IPv6 System Status, Wireless 2.4 GHz
Status, Wireless 5.0 GHz Status and Statistics
In addition there are button to Renew DHCP Leases, View System Logs, Clients List, NAT Status and to Refresh the status page.
Figure 12: Advanced View – Status
YML27
www.netcommlimited.com
NetComm NF2 User Guide
24
Network Setup
Network Setup
Ethernet WAN
This page allows you to setup the Ethernet WAN (Wide Area Network) interface of the NF2 router. This is for an internet connection
through the WAN port of the router instead of using a Mobile Broadband (MBB) WWAN connection.
Figure 14: Advanced View – Ethernet WAN Settings
OPTION
DEFINITION
WAN Interface
Enter the WAN interface required. Options are Ethernet WAN or Wireless WAN (3G/4G Mobile Broadband).
WAN Type
Enter the WAN type of the WAN interface; Options include Dynamic IP Address (default), Static IP address,
PPP over Ethernet (PPPoE), PPTP and L2TP.
Automatic 3G Backup
Select the Enable checkbox to enable automatic MBB backup of the Ethernet WAN interface. Enter an IP
address or domain name into the Remote Host for Keep Alive field for the router to periodically check the status
of the connection.
Host Name
This optional field can be used to create a domain name instead of using the IP address of the router to access
the management console locally.
ISP Registered MAC Address
Press the clone button for the router to automatically detect the MAC address of the WAN interface.
NAT
Select this option if NAT (Network Address Translation) is required. In most cases NAT will be required.
Therefore NAT is enabled by default.
Multicast
Select whether which version IGMP (Internet Group management Protocol) is required for your WAN
connection. In most cases the Auto connection will suffice.
IGMP Snooping
Select whether you wish IGMP enabled on the WAN connection. IGMP snooping is the process of listening to
(IGMP) network traffic. IGMP snooping, as implied by the name, allows the router to listen in on the IGMP
conversation between computers and the routers. By listening to these conversations the router maintains a
map of which links need which IP multicast streams. Multicasts may be filtered from the links which do not
need them.
Table 11 - Advanced View – Ethernet WAN Settings
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
25
YML38
www.netcommlimited.com
Wireless WAN
This page allows you to configure the Mobile Broadband (MBB) settings for use as the WAN interface of the router.
Figure 15: Advanced - Network Setup - Wireless WAN Setup
OPTION
DEFINITION
WAN Interface
Enter the WAN interface required. Options are Ethernet WAN or Wireless WAN (3G/4G Mobile Broadband).
Country
Enter the Country where the 3G/4G Internet Provider is operating. This field affected such settings as dial and
ring tones, and the prefixes that need to be entered before making a call.
Choose an APN here
Enter your MBB (Mobile Broadband) provider here. Enter the Access Point Name that your MBB (Mobile
Broadband) provider has recommended you use.
APN
Enter the Access Point Name that your MBB (Mobile Broadband) provider has recommended you use.
PIN Code
If your SIM card requires a PIN code, enter it in here.
Dial
The string value that needs to be dialled to make a 3G/4G connection. *99#
Authentication Type
Select the authentication type used by the MBB connection. If you are unsure what this is select the Auto
option.
Primary DNS
Enter the Primary Domain Name Server address used by the MBB connection.
Secondary DNS
Enter the Secondary Domain Name Server address used by the MBB connection.
Connection Control
Select from the connection control options:
Connect on Demand – Connect when a MBB WAN interface is attempting to make a connection.
Auto Reconnect (always on) – Assume the MBB connection is always on and try to connect if the MBB
connection is dropped.
Manually – Connect the Wireless WAN interface only when a manual attempt is made.
MTU
Enter the Maximum Transmission Unit, the size of the largest packet that a network protocol can transmit.
Keep Alive
A mechanism for testing whether the MBB connection is active or not by periodically pinging a remote host.
Multicast
Select whether which version IGMP (Internet Group management Protocol) is required for your WAN
connection. In most cases the Auto connection will suffice.
IGMP Snooping
YML27
www.netcommlimited.com
Select whether you wish IGMP enabled on the WAN connection. IGMP snooping is the process of listening to
(IGMP) network traffic. IGMP snooping, as implied by the name, allows the router to listen in on the IGMP
conversation between computers and the routers. By listening to these conversations the router maintains a
map of which links need which IP multicast streams. Multicasts may be filtered from the links which do not
need them.
Table 12: Advanced - Network Setup - Wireless WAN
NetComm NF2 User Guide
26
DHCP
DHCP is the means used so that all computers connected to the router can be assigned an IP address. This is essential before
communications can start over the internet. Generally it is recommended to leave DHCP as default (enabled) unless instructed
otherwise by your Internet Service Provider.
Figure 16: Advanced – DHCP
OPTION
DEFINITION
DHCP Server
The option to disable or enable the DHCP function.
LAN IP Address
The LAN IP address of the DHCP server/router.
Subnet Mask
The subnet mask used by the DHCP server.
IP Pool Starting Address
The stating IP address for the DHCP pool, in the above example is 192.168.20.100
IP Pool Ending Address
The ending IP address for the DHCP pool, in the above example is 192.168.20.200
Lease Time
The time in seconds that an IP address is leased for
Domain Name
The domain of the DHCP server.
Primary DNS
Enter the Primary Domain Name Server address used by the DHCP server.
Secondary DNS
Enter the Secondary Domain Name Server address used by the DHCP server.
Primary WINS
Enter the Primary WINS (Windows Internet Name Server) address used by the DHCP server.
Secondary WINS
Enter the Secondary WINS (Windows Internet Name Server) address used by the DHCP server.
Table 13: Advanced - DHCP Settings
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
27
YML38
www.netcommlimited.com
Wireless 2.4 GHz
This page allows the user to configure the 2.4 GHz wireless settings on the NetComm NF2 including the wireless security types,
wireless encryption, WDS (Wireless Distributed System) settings and WPS (Wireless Protected Setup) setup.
Figure 17: Advanced - Wireless 2.4 GHz
OPTION
DEFINITION
Wireless Module (2.4GHz)
The option to disable or enable the wireless 2.4 GHz function.
Network ID (SSID)
The SSID (Service Set Identifier) is the name of your wireless network. Use a unique name to identify your
wireless device so that you can easily connect to it from your wireless clients. This field is case sensitive and
can be up to 32 characters in length. It is recommended that the default SSID be changed for added security.
SSID Broadcast
Enabled by default, this field enables or disables the SSID broadcast, deciding whether the SSID will be hidden
to all wireless clients, requiring a manual configuration to connect to the network or whether the SSID can be
detected by wireless clients.
Channel
The wireless frequency used by the 2.4 GHz connection. Recommended channels to use include 1, 6 and 11.
Wireless Mode: There are 6 modes to select from:
802.11b/g mixed mode:
Both 802.11b and 802.11g wireless devices can connect to the NetComm NF2.
802.11b only:
Select this if all of your wireless clients use 802.11b wireless protocol.
802.11g only:
Select this if all of your wireless clients are 802.11g wireless protocol.
802.11n only:
Select this if all of your wireless clients are 802.11n wireless protocol.
802.11g/n Mixed mode:
Select this if 802.11g and 802.11n wireless devices access your network.
802.11/b/g/n Mixed mode:
Select this if 802.11b and 802.11g and 802.11n wireless devices access your network.
Authentication
This field allows you to select the authentication type of the wireless security for the 2.4 GHz wireless network
connection.
802.1x
This field gives the option to enable or disable the 802.1x authentication protocol.
Encryption
With this field the encryption that the wireless security will use on the 2.4 GHz wireless network can be
selected.
Preshare Key
The wireless security password for the 2.4 GHz wireless network connection.
Table 14: Advanced Wireless 2.4 GHz Settings
YML27
www.netcommlimited.com
NetComm NF2 User Guide
28
WDS Settings
WDS (Wireless Distribution System) is a system that enables the wireless interconnection of access points, and allows a wireless
network to be expanded using multiple access points without using a wired backbone to link them. To successfully link each WDS
Access Point needs to be set with the same channel, SSID, encryption type and encryption key.
Figure 18: Advanced –WDS
Enter the MAC address of each Remote Access Point and press the Save button.
WPS Setup
WiFi Protected Setup is a computer standard that offers a quick and easy alternative to setting up a wireless network. WPS can be
configured using a push button method or by using a PIN code.
Figure 19: Advanced - WPS Setup
OPTION
DEFINITION
WPS
Enable or disable WPS with this field.
AP PIN
Set the Access Point PIN by pressing the Generate New PIN button.
Config Mode
Select from being an enrolee or registrar. In most cases the router will be the registrar.
Config Status
This field gives the current WPS status. Press either the Release button to release a configured WPS setting or
the Set button to configure the current WPS settings
Config Method
Select whether WPS should use Push button or PIN Code mode for its configuration.
WPS Status
This field advises the current WPS status.
Table 15: Advanced - WPS Setup settings
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
29
YML38
www.netcommlimited.com
Wireless 5.0 GHz
This page allows the user to configure the 5.0 GHz wireless settings on the NetComm NF2 including the wireless security types,
wireless encryption, WDS (Wireless Distributed System) settings and WPS (Wireless Protected Setup) setup.
Figure 20: Advanced - 5.0 GHz Wireless
OPTION
DEFINITION
Wireless Module (5.0GHz)
The option to disable or enable the wireless 5.0 GHz function.
Network ID (SSID)
The SSID (Service Set Identifier) is the name of your wireless network. Use a unique name to identify your
wireless device so that you can easily connect to it from your wireless clients. This field is case sensitive and
can be up to 32 characters in length. It is recommended that the default SSID be changed for added security.
SSID Broadcast
Enabled by default, this field enables or disables the SSID broadcast, deciding whether the SSID will be hidden
to all wireless clients, requiring a manual configuration to connect to the network or whether the SSID can be
detected by wireless clients.
Channel
The wireless frequency used by the 5.0 GHz connection. Recommended channels to use include 1, 6 and 11.
Wireless Mode: There are 6 modes to select from:
802.11b/g mixed mode:
Both 802.11b and 802.11g wireless devices can connect to the NetComm NF2.
802.11b only:
Select this if all of your wireless clients use 802.11b wireless protocol.
802.11g only:
Select this if all of your wireless clients are 802.11g wireless protocol.
802.11n only:
Select this if all of your wireless clients are 802.11n wireless protocol.
802.11g/n Mixed mode:
Select this if 802.11g and 802.11n wireless devices access your network.
802.11/b/g/n Mixed mode:
Select this if 802.11b and 802.11g and 802.11n wireless devices access your network.
Authentication
This field allows you to select the authentication type of the wireless security for the 5.0 GHz wireless network
connection.
802.1x
This field gives the option to enable or disable the 802.1x authentication protocol.
Encryption
With this field the encryption that the wireless security will use on the 5.0 GHz wireless network can be
selected.
Preshare Key
The wireless security password for the 5.0 GHz wireless network connection.
Table 16: Advanced - Network Setup - 5.0 GHz Wireless Settings
YML27
www.netcommlimited.com
NetComm NF2 User Guide
30
VPN – IPSec
This page allows the NetComm NF2 to act as a VPN IPSec endpoint. Internet Protocol Security (IPsec) is used to secure IP (Internet
Protocol) communications by authenticating and encrypting each IP packet of a communication session. IPsec also includes
protocols for establishing mutual authentication between agents at the beginning of the session and negotiation of cryptographic
keys to be used during the session.
Figure 21: Advanced - Network Setup - IPSec
OPTION
DEFINITION
VPN-IPSEC
Select this checkbox to enable the router as a VPN-IPSec endpoint.
Netbios over IPSEC
Select this checkbox to enable Netbios over IPSEC.
NAT Traversal
Select this option to enable NAT Traversal of the IPSec connection.
VPN Statistic
Select this field to enable VPN statistics – including the VPN tunnel name, elapsed time of the VPN tunnel,
incoming and outgoing packets.
Max. Number of Tunnels
Enter the maximum number of VPN tunnels that can be created at any one time.
Dynamic VPN
This field will create a VPN tunnel using dynamic IP addresses.
Table 17: Advanced - Network Setup -VPN-IPSec
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
31
YML38
www.netcommlimited.com
VPN – IPSec Tunnel Setup
This page allows you to configure a VPN endpoint IPSec.
Figure 22: Advanced - Network Setup - Dynamic IPSec
OPTION
DEFINITION
Tunnel Name
Enter the VPN tunnel name.
Local Subnet
Enter the Local Subnet address.
Local Network
Enter the Local Network address.
Phase 1 Key Life Time
Enter the Phase 1 Key Life Time in seconds.
Phase 2 Key Life Time
Enter the time in seconds for the Phase 2 Key Life Time.
Encapsulation Protocol
Enter the encapsulation protocol for the VPN tunnel. Options are ESP (Encapsulated Security Payload), AH
(Authentication Header) or ESP + AH.
PFS Group
Select the PFS (Perfect Forward secrecy) Group to be used.
Remote ID
Enter the remote ID and select the Remote ID type. Options include Username, FQDN (Fully Qualified Domain
Name), User@FQDN or Key ID.
Local ID
Enter the local ID and select the local ID type. Options include Username, FQDN (Fully Qualified Domain Name),
User@FQDN or Key ID
Dead Peer Detection (DPD)
Select to enable Dead Peer Detection, a means of detecting a dead IKE (Internet Key Exchange) peer. Set the
timeout and delay in seconds.
Set IKE Proposal
YML27
www.netcommlimited.com
Select to Enable IKE (Internet Key Exchange) Proposals.
Table 18: Advanced - Network Setup - VPN IPSec - Dynamic IPSec
NetComm NF2 User Guide
32
VPN-L2TP
This page allows you to configure a Layer 2 Tunnelling protocol. It does not provide any encryption or confidentiality by itself; it relies
on an encryption protocol that it passes within the tunnel to provide privacy.
Figure 23: Advanced - Network Setup - L2TP
VPN-PPTP Client
The Point-to-Point Tunnelling Protocol (PPTP) is a method for implementing virtual private networks. PPTP uses a control channel
over TCP and a GRE tunnel operating to encapsulate PPP packets.
Figure 24: Advanced - Network Setup - PPTP Client
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
33
YML38
www.netcommlimited.com
VPN – PPTP Server
This page allows the NetComm NF2 to become a PPTP VPN endpoint.
Figure 25: Advanced - Network Setup - VPN - PPTP Server
OPTION
DEFINITION
VPN-PPTP Server
Select this option to enable the VPN-PPTP Server function.
Server Virtual IP
Enter the IP address of the PPTP server.
IP Pool Start Address
The starting IP address for the DHCP pool, in the above example is 192.168.0.10.
IP Pool End Address
The ending IP address for the DHCP pool, in the above example is 192.168.0.100
Authentication Protocol
Select the authentication protocol you wish to use.
MPPE Encryption Mode
Select to enable MPPE Encryption Mode (Microsoft Point-to-Point Encryption).
NAT
Select to enable NAT on the PPTP server.
Encryption length
Enter encryption length for the packets sent through the VPN tunnel.
Table 19: Advanced - Network Setup - VPN - PPTP Server Settings
YML27
www.netcommlimited.com
NetComm NF2 User Guide
34
Change Password
This page allows you to change the administrator username and password to secure the NetComm NF2 management console
against unauthorised access.
Figure 26: Advanced - Network Setup - Change Password
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
35
YML38
www.netcommlimited.com
Forwarding Rules
The forwarding rules section deals with NAT traversal. Using the Virtual Server settings port forwarding can be configured. Special
AP settings can be used to configure port triggering. In the Miscellaneous section a DMZ host can be configured and UPnP can be
enabled or disabled.
Virtual Server
The Virtual Server page allows you to direct incoming traffic from the Internet side (identified by Protocol and External port) to the
internal server with a private IP address on the LAN side. The Internal port is required only if the external port needs to be converted
to a different port number used by the server on the LAN side. A maximum of 20 entries can be configured. In addition a series of
pre-configured commonly used ports can be selected for easy setup.
Figure 27: Advanced - Forwarding Rules - Virtual Server
OPTION
DEFINITION
Service Ports
Enter the port number or port range to be used with the Server IP address. For a port range entry use the
format shown in the following example (81-90).
Server IP
Enter the local IP address of the device you wish to port forward to.
Enable
Select this option to enable the port forwarding rule.
Use Rule
Select when the port forwarding rule should be used. The default option is Always.
Table 20: Advanced - Forwarding Rules - Virtual Server Settings
YML27
www.netcommlimited.com
NetComm NF2 User Guide
36
Special AP
The Special AP page allows the router to be configured for port triggering. Port triggering allows a client device connected to the
router to dynamically and automatically forward a specific port back to itself. Port triggering opens an incoming port when your
computer is using a specified outgoing port for specific traffic. A selection of common port triggering settings come preconfigured
on the NF2 for easy setup.
Figure 28: Advanced - Forwarding Rules - Port Triggering
OPTION
DEFINITION
Trigger
Enter the outgoing trigger port be opened by a device connected to the router.
Incoming Ports
Enter the incoming port number or port ranges. For a port range use a dash (-) between the lower and upper
range numbers; e.g. 5000-6000. Use a comma between multiple numbers.
Enable
Select this option to enable or disable the port triggering rule.
Table 21: Advanced - Forwarding Rules - Port Triggering Settings
Miscellaneous
The miscellaneous page gives the user the option of enabling or disabling UPnP protocol or the option to assign a device connected
to the router as a DMZ host. A DMZ host is a host on the internal network that has all ports exposed to a WAN connection, except
those ports otherwise forwarded.
Figure 29: Advanced - Forwarding Rules - Miscellaneous
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
37
YML38
www.netcommlimited.com
Security Settings
The security settings menu has such configuration options for the NetComm NF2 as Packet Filtering, MAC Filtering, Domain
Filtering, URL Blocking, MAC Control and Remote Administration settings.
Status
The Security Settings Status page provides an overview of the current IP filter, MAC filter and domain filter rules in place on the NF2.
Figure 30: Advanced - Security Settings – Status
Packet Filtering
The inbound and outbound packet filtering function gives the network administrator the option of denying or allowing data packets
to be transmitted through to the WAN interface when any of the specified rules are met. Conversely any other data packets not
matching these rules will be denied or allowed access through the network as specified by the network administrator.
Figure 31: Advanced - Security Settings - Packet Filtering
YML27
www.netcommlimited.com
NetComm NF2 User Guide
38
OPTION
DEFINITION
Source IP
Enter the local source IP address where the packet originates from for an outgoing packet filter rule or is being
sent to for an incoming packet filter rule.
Destination IP: Ports
Enter the WAN IP address and port number or range where the packet is directed to or from..
Enable
Select this option to make the packet filter rule active.
Use Rule#
Select when the rule is to be used. The default value is Always.
Table 22: Advanced - Security Settings - Packet Filtering Settings
MAC Control
The MAC filter function can be used to restrict access to the NF2 for both wired and wireless clients. Using Connection Control
wired and wireless clients can connect to the router and either allow or deny any unspecified MAC addresses connection access.
Using association control wireless clients can associate to the wireless LAN. All other unspecified wireless clients can be allowed or
denied association rights.
Figure 32: Advanced - Security Settings - MAC Filtering
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
39
YML38
www.netcommlimited.com
Domain Filter
Domain Filtering can be used to monitor and or deny access to specified domain names.
Figure 33: Advanced - Security Settings - Domain Filter
OPTION
DEFINITION
Domain Filter
Select this option to enable Domain Filtering
Log DNS Query
Select this option to log DNS Queries for all specified domain names.
Privilege IP Addresses Range
Enter the range of IP addresses that will not be filtered.
Domain Suffix
Enter the domain name you wish to deny or have log.
Drop
Select drop if you wish to deny access to the specified domain name
Log
Select Log if you wish to log any attempts to access the specified domain name.
Enable
Select this option to enable the domain filter rule.
Table 23: Advanced - Security Settings - Domain Filtering Settings:
YML27
www.netcommlimited.com
NetComm NF2 User Guide
40
URL Blocking
The URL blocking function can deny access to specified URL addresses.
Figure 34: Advanced - Security Settings - URL Blocking
Miscellaneous
The Security Settings Miscellaneous section provides access to remote administration settings, administrator time out and DoS
(Denial of Service) Attack Detection amongst other things.
Figure 35: Advanced - Security Settings - Miscellaneous
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
41
YML38
www.netcommlimited.com
Advanced Settings
The Advanced Settings menu has System log, Dynamic DNS, QoS (Quality of Service), SNMP (Simple Network Management
Protocol), Routing, System Time, Scheduling, IPv6, TR-069 and VLAN options.
Status
The status page shows the current status of the Advanced Settings on the NF2.
Figure 36: Advanced - Advanced Settings – Status
System Log
As well as viewing the system log entries locally the System Log page allows a network administrator to configure the router’s
system log to be sent to a remote system log server or to be emailed to nominated email addresses of the administrator’s choice.
Figure 37: Advanced - Advanced Settings - System Log
YML27
www.netcommlimited.com
NetComm NF2 User Guide
42
OPTION
DEFINITION
IP Address for Syslog Server
For sending the system log information to a remote server, enter the IP address of your System Log server.
Email Address to Send Syslog to
If you would like to send the system log details via email select this option and enter the appropriate details.
SMTP Server: port
Enter the name of the outgoing mail server to use in sending out the system log server.
SMTP Username
If a username is required for the outgoing mail server, enter it into this field.
SMTP Password
If a password is required for the outgoing mail server, enter it into this field.
Email Addressees
Enter the email addresses of where you wish the system log details to be sent to.
Email Subject
Enter a Subject for the System Log Email.
View Log
View the System Log entries locally.
Email Log Now
If the email settings are correct the emails containing the system log will be sent on pressing this button.
Table 24: Advanced - Advanced Settings - System Log Settings
Dynamic DNS
Dynamic DNS or DDNS is used for the updating in real time of Domain Name System (DNS) name servers to keep the active DNS
configuration of their hostnames, addresses and other information up to date. To use these settings you will need a dynamic DNS
account with Dyndns.org, No-IP.com, TZO.com or dhs.org.
Figure 38: Advanced - Advanced Settings - Dynamic DNS
OPTION
DEFINITION
DDNS
The option to disable or enable the DHCP function.
Provider
Select your dynamic DNS provider.
Host Name
Enter the hostname / host domain name / host address.
Username / Email
Enter the dynamic DNS account username.
Password / Key
Enter the dynamic DNS account password.
Table 25: Advanced - Advanced Settings - Dynamic DNS Settings
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
43
YML38
www.netcommlimited.com
QoS (Quality of Service)
Quality of Service (QoS) refers to resource reservation control mechanisms with the ability to provide a different priority to different
applications, users, or data flows, or to guarantee a certain level of performance to a data flow. For example, a required packet
transfer rate or delay may be guaranteed.
Figure 39: Advanced - Advanced Settings - QoS
OPTION
DEFINITION
QoS
Select the Enable option to enable Quality of Service (QoS).
WAN Interface
Select the WAN interface you wish to configure QoS for.
QoS Mode
Select the QoS Mode to use.
Bandwidth of Upstream
Set the Upstream limit in Kilobits per second (Kbps).
Bandwidth of Downstream
Set the Downstream limit in Kilobits per second (Kbps).
Flexible Bandwidth Management
Select this option to Enable to allow the router to assign the QoS percentage rates or set this option to
disable and manually enter the QoS percentage rates for the Item fields.
Table 26: Advanced - Advanced Settings - QoS Settings
SNMP
SNMP, short for Simple Network Management Protocol is used mostly in network management systems to monitor networkattached devices for conditions that warrant administrative attention. SNMP consists of a set of standards for network
management, including an application layer protocol, a database schema, and a set of data objects.
Figure 40: Advanced - Advanced Settings - SNMP
YML27
www.netcommlimited.com
NetComm NF2 User Guide
44
OPTION
DEFINITION
Enable SNMP
The option to disable or enable the SNMP function.
Get Community
An SNMP community is the group that devices and management stations running SNMP belong to. It helps
define where information is sent. The Get Community field gets the current community name is used to identify
the group. A SNMP device or agent may belong to more than one SNMP community. It will not respond to
requests from management stations that do not belong to one of its communities. SNMP default communities
are: Write – private; Read – public.
Set Community
An SNMP community is the group that devices and management stations running SNMP belong to. It helps
define where information is sent. The Set Community field sets the new community name used to identify the
group. A SNMP device or agent may belong to more than one SNMP community. It will not respond to
requests from management stations that do not belong to one of its communities. SNMP default communities
are: Write – private; Read – public.
IP 1
Enter the IP address for one of the local clients connected to router. SNMP will then gather and transmit the
network information that you specified.
IP 2
Enter the IP address for the second of the local clients connected to router. SNMP will then gather and transmit
the network information specified.
IP 3
Enter the IP address for the third of the local clients connected to router. SNMP will then gather and transmit
the network information specified.
IP 4
Enter the IP address for the fourth of the local clients connected to router. SNMP will then gather and transmit
the network information specified.
SNMP Version
Select the version SNMP you wish to use with the NF2.
WAN Access IP Address
Enter the WAN Access IP Address used to provide (WAN) Wide Area Network connectivity to the internet.
Table 27: Advanced - Advanced Settings - SNMP Settings
Routing
The Routing page in the Advanced Settings section of the NF2 provides a network administrator with the means to configure the
routing method that the NF2 will use, either dynamic routing or static routing. Routes are called static if they do not change over
time. Thus a static routing table is loaded with values when the system starts and the routes do not change unless an error is
detected. Conversely, dynamic routing refers to a system that can change its routing table information over time. With dynamic
routing, software known as RIP (Routing Information Protocol) interacts with network devices and learns the optimal route to each
location. Then RIP updates the local routing table to ensure datagrams follow the optimal routes.
Figure 41: Advanced - Advanced - Settings - Routing
Dynamic Routing: Routing Information Protocol (RIP) will exchange information about different host destinations for working out
routes throughout the network.
Please note: Only select RIPv2 if you have a different subnet in your network. Otherwise, please select RIPv1.
Static Routing: For static routing, you can specify up to 8 routing rules. You need to enter the destination IP address; subnet mask,
gateway, and hop for each routing rule, then enable the rule by clicking the Enable checkbox.
Click on "Save" to store your setting or "Undo" to discard your changes.
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
45
YML38
www.netcommlimited.com
System Time
The NF2 router time can be synchronised either to a local PC or using NTP (Network Time Protocol) settings to a standard global
internet time. These settings will affect functions such as System Log statistics, scheduling and Firewall settings
Figure 42: Advanced - Advanced Settings -System Time
OPTION
DEFINITION
Time Zone
Select the GMT offset for your location.
Auto-Synchronization
Select an NTP (Network Time Protocol) time server to synchronise to the global internet time with.
Sync with Time Server
Select this button to initiate the router time synchronisation to the specified network time server above.
Sync with my PC
Select this button to initiate the router time synchronization to the computer you are currently logged into the
router with.
Table 28: Advanced - Advanced Settings - System Time
Scheduling
The NF2 has built in scheduling, allowing the router to be switched on or off. This offers a means of parental control. To create a
schedule, ensure the enable Schedule option is selected and press the Add New button.
Figure 43: Advanced - Advanced Settings – Schedule
YML27
www.netcommlimited.com
NetComm NF2 User Guide
46
Adding a Schedule
Figure 44: Advanced - Advanced Settings - Adding a Schedule
OPTION
DEFINITION
Name of Rule
Enter a name for the Schedule.
Policy
Use the Policy option to set each rule defined to Activate or Deactivate the router except the selected days and
hours below.
Week Day
Select the day(s) of the week you wish the rule to be used on.
Start Time (hh:mm)
Enter the Start time for the rule to begin.
End Time (hh:mm)
Enter the End time for the rule to end.
Table 29: Advanced - Advanced settings - Adding a Schedule Settings
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
47
YML38
www.netcommlimited.com
IPv6
The NF2 router can be configured to use IPV6 routing configuration.
Figure 45: Advanced - Advanced Settings - IPV6
OPTION
IPv6
DEFINITION
The option to enable or disable IPv6.
Select the type of IPv6 for the router to use. Options include :

Dynamic DHCPv6 - an IPv6 address is assigned by the router automatically,

Static IPv6 - a static IPv6 address assigned by an Internet Service Provider can be assigned
to the router.
IPv6 Connection

PPPoE – for using an IPv6 address over PPPoE.

6 to 4 – This option converts an IPv6 address to an IP v4 address.

IPv6 in IPv4 tunnel – This option uses an IPv6 address through an IPv4 tunnel.
DNS Setting
Select Obtain a DNS Server address automatically assigned by the router or assign your own static Primary
and Secondary DNS addresses.
LAN IPv6 Address
Enter the local IPv6 address in this field.
Auto-configuration
Select to enable auto configuration of the IPv6 address.
Auto-configuration Type
Select either Stateless or Stateful IPv6 auto configuration. Stateless Address Auto configuration (or SLAAC) can
be used by devices connecting to a routed network using Internet Control Message Protocol version 6
(ICMPv6) router discovery messages. This is generally streamlined and simplified compared to Stateful Autoconfiguration. Stateful IPv6 also known as DHCPv6 uses a dedicated configuration mechanism that is more
comprehensive than Stateless Auto configuration catering to all the information needs in the form of required
parameters to the network devices
Router Advertisement lifetime
YML27
www.netcommlimited.com
When a computer host first connects to the NF2 router using IPv6 it sends a link-local router solicitation
multicast request for its configuration parameters. If the NF2 router is configured correctly it will respond with a
router advertisement packet that contains network-layer configuration parameters. The Router advertisement
lifetime is the amount of time that the router advertisement is broadcast as a multicast after receiving the
request.
Table 30: Advanced - Advanced Settings – IPv6 Settings
NetComm NF2 User Guide
48
TR-069
The TR-069 (technical report 069) protocol uses a SOAP/HTTP protocol to provide communications between Customer-Premises
Equipment (CPE) and an Auto-Configuration Server (ACS) for the purpose of automated configuration of the CPE devices.
Figure 46: Advanced - Advanced Settings - TR-069
OPTION
DEFINITION
TR-069
Select the enable option to enable the TR-069 protocol on the NF2.
ACS URL
Enter the URL of the Auto-Configuration Server in this field.
ACS UserName
Enter the user name of the Auto-Configuration Server here.
ACS Password
Enter the password of the Auto-Configuration Server here.
Connection Request Port
Enter the port number to be used by a CPE in sending an Inform message to the ACS server to initialise a
connection.
Connection Request
UserName
Enter the Connection Request username to be used by each of the CPE devices to authenticate with the ACS
server.
Connection Request Password
Enter the Connection Request password to be used by each of the CPE devices to authenticate with the ACS
server.
Inform
Set the Inform to enable or disable to accept or deny an inform message from a CPE device to the ACS server.
Interval
Enter the interval in seconds between Inform messages being sent to the ACS server.
Table 31: Advanced - Advanced Settings - TR-069
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
49
YML38
www.netcommlimited.com
VLAN
The VLAN section of the NF2 allows for the creation of a virtual LAN across one or more of the Ethernet and wireless interfaces
Figure 47: Advanced – Advanced Settings – VLAN
Enter the Virtual ID for each Ethernet port and tick whether the data transmitted needs to be tagged, a part of VLAN tagging.
For WAN VLAN settings press the WAN VLAN Settings button.
Figure 48: Advanced - Advanced Settings - VLAN - WAN VLAN
Select the appropriate VID (Virtual ID) and select the Routing Type, either NAT or Bridging. Press the Save button to save any
changes to the settings.
YML27
www.netcommlimited.com
NetComm NF2 User Guide
50
NAS Settings
The NAS (Network Attached Storage) settings allow the NF2 to act as a file server. Options available include Disk Utility, File
Sharing, Access Control, iTunes Server, Download Assistant, Download Status and Web HDD.
Disk Utility
Using the disk utility function a connected USB drive will be detected and displayed as the example in Figure 47 shows. The option
to format the drive can also be found on this by pressing the Format button. The drive can be checked for integrity by pressing the
Check button and Unmounted by pressing the Unmount button.
Figure 49: Advanced - Advanced Settings - Disk Utility
File Sharing
The file sharing option under NAS settings allows the router NAS (Network Attached Storage) to join an existing network
Workgroup. An FTP connection to the NAS device can also be configured by pressing the FTP Service Configuration button.
Figure 50: Advanced - NAS Settings - File Sharing
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
51
YML38
www.netcommlimited.com
FTP Service Configuration
The FTP (File Transfer Protocol) Service Configuration allows the NAS storage files to be accessed and transmitted over a TCP
based network.
Figure 51: Advanced - NAS Settings - File Sharing -FTP Service Configuration
OPTION
DEFINITION
FTP
Select this option to enable or disable the FTP function.
FTP Port
Enter the port number to be used by the FTP protocol.
FTP Max Connection per IP.
Select the maximum number of FTP connections over any one IP address.
FTP Max Clients
Select the maximum number of clients that can connect via FTP at any one time.
Client Support UTF8
YML27
www.netcommlimited.com
Select whether the router will support client connections with UTF-8, one of the most common Unicode
standards. As the name implies UTF-8 uses one byte (8 bits) for any ASCII character and up to 4 bytes for
other characters.
Table 32: Advanced - NAS Settings - File Sharing - FTP Service Configuration
NetComm NF2 User Guide
52
Access Control
The Access Control section of the NF2 NAS Settings, allow a network administrator to set either a guest level security with no
authentication required or to use authentication mode where a username and password is required to access the NAS server files.
Figure 52: Advanced - NAS Settings -Access Control
To setup authentication for the NAS storage select Authorization Mode and press the User Configuration button.
Figure 53: Advanced - NAS Settings - Access Control – Authentication Mode
Enter a user name and password and press the Add button to save the authentication details. Up to 20 usernames and passwords
for NAS storage authentication can be stored on the router.
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
53
YML38
www.netcommlimited.com
iTunes Server
The iTunes Server function enables any applicable media on any attached USB storage to be directly access from within iTunes. To
enable this, click on the ‚Enable‛ radio button in the ‚Service‛ section. Click the ‚Save‛ button to save any configuration changes you
have made
Figure 54: Advanced - NAS Settings - iTunes Server
NAME
Service
iTunes Shared
Library Name
iTunes Shared
Library password
(required)
Service Port
DESCRIPTION
Select this option to enable or disable the iTunes Server functionality.
Enter the name that will appear in your iTunes application as a library list.
Enter the password required to access your iTunes server content.
Enter the port number that the iTunes Shared Library uses to connect with the internet. The default port number is 3369.
Table 33: Advanced - NAS Settings - iTunes Server
YML27
www.netcommlimited.com
NetComm NF2 User Guide
54
Download Assistant
The download assistant gives the user a means of automating the downloading of files from the internet at scheduled dates and
times to a location of the user’s choice. There are two methods available to complete the downloading, FTP and HTTP.
Figure 55: Advanced - NAS Settings - Download Assistant – FTP
Figure 56: Advanced - NAS Settings - Download Assistant - HTTP
OPTION
DEFINITION
Download Type
Select the protocol to use to complete the download.
Job Name
Enter a name for the download job.
URL/Port
Enter the path and filename and port number to the document to be downloaded. The default port number for
using FTP is port 21.
Save To
Enter the local location where the file will be saved to.
Login Method
Select the authentication required if any. For no authentication use anonymous. For use with an FTP account
select Account.
Username
Enter the username for an FTP account.
Password
Enter the Password for an FTP account.
Start Time
Select the date/time for the download to commence.
Email Alert Configuration
Press this button to setup an email alert to advise a network administrator that the download has completed.
Table 34: Advanced - NAS Settings - Download Assistant Settings
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
55
YML38
www.netcommlimited.com
Download Assistant – Email Alert
To set up an email to alert the network administrator that a download is complete select the Email Alert Configuration button. The
following screen will appear.
Figure 57: Advanced - NAS Settings - Download Assistant - Email Alert
OPTION
DEFINITION
HTTP Download Alert
Use this option to disable or enable the HTTP Download Alert function.
FTP Download Alert
Use this option to disable or enable the FTP Download Alert function.
USB Download Alert
Use this option to disable or enable the USB Download Alert function.
SMTP Server Address
Enter the SMTP outgoing email server address that will be used to send emails from the router.
SMTP Server Port
Enter the port number that the SMTP server uses.
SMTP User Name
If required by the SMTP server, enter the SMTP user name.
SMTP Password
If required by the SMTP server, enter the SMTP password.
Email Address
Enter the Email address to send the Download Alert Email to.
Email Subject
Enter the Email Subject that the Download Alert Email will have.
Reservation Disk Space
Enter the amount of disk space (in MB) that the Download Alert Emails will need.
Table 35: Advanced - NAS Settings - Download Assistant - Email Alert Settings
Download Status
The download status page lists all downloads that are running, waiting to run or are scheduled to run.
Figure 58: Advanced - NAS Settings - Download Status
YML27
www.netcommlimited.com
NetComm NF2 User Guide
56
Web HDD
The Web HDD function provides a web page based Windows Explorer type view of the content of any attached USB storage. Using
this interface you are able to upload, download or delete files and folders as well as create directories. Click through the displayed
folders to show any stored files.
Figure 59: Advanced - NAS Settings - Web HDD
Single click on any items to select them and click the appropriate button or double click folders to view any content.
Figure 60: Advanced - NAS Settings - Web HDD - Upload File
You can then click the Browse‛ button and then navigate to the file you would like to upload. To upload files to your Web HDD click
the Upload button. Once selected, this file will be copied to the Web HDD and become available to download by connected
devices.
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
57
YML38
www.netcommlimited.com
Toolbox
The Toolbox menu provides access to maintenance settings of the NF2. Menu options include System Info, Restore Settings,
Firmware Upgrade, Backup Settings, Reset to Default, Reboot, Startup Wizard, Miscellaneous and Logout.
System Info
The System Info section provides access to the system log entries of the NF2. The system log entries can be saved to a file by
pressing the Download button at the bottom of the page.
Figure 61: Advanced - Toolbox - System Info
YML27
www.netcommlimited.com
NetComm NF2 User Guide
58
Restore Settings
The restore settings page can be used to load a previously saved router configuration. It is recommended using an Ethernet cable
connection to upload any configuration settings. Do not power off the router until the configuration settings are successfully updated
and the router has automatically restarted.
Figure 62: Advanced - Toolbox - Restore Settings
Firmware Upgrade
This page can be used to upload the latest firmware version for the NF2 as it becomes available.
Figure 63: Advanced - Toolbox - Firmware Upgrade
Click the "Browse" button and navigate to the location where you have saved the firmware update file. You can then upgrade the
firmware by clicking the "Upgrade" button. Do not power off the device until the firmware upgrade has completed and the router
has automatically restarted.
Backup Settings
This option allows the network administrator to save the configuration settings of the NF2 to a file that can be uploaded to another
NF2 or uploaded into the NF2 at a later date. The name of the file can be changed but it is recommended to leave the suffix as .bin.
Figure 64: Advanced - Toolbox - Backup Settings
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
59
YML38
www.netcommlimited.com
Reset to Default
This option can be used to reset all settings on the NF2 to factory default settings. It is recommended to reset the router to factory
default settings after a firmware upgrade.
Figure 65: Advanced - Toolbox - Reset to Default
Reboot
Use this option to reboot the router after making any changes to the configuration settings.
YML27
www.netcommlimited.com
NetComm NF2 User Guide
60
Startup Wizard
The Startup Wizard option will return the user to the NF2 Startup wizard so that the router can be reconfigured.
Figure 66: Advanced - Toolbox - Startup Wizard
Miscellaneous
The Miscellaneous page provides settings for Wake on LAN, has provision for ping tests, and has the option to DIM the LEDs on the
front of the unit. Wake-on-LAN enables the router to start-up a computer or device (if the computer supports it) when a WOL
packet is detected on the network going to the client MAC you have entered.
Figure 67: Advanced - Toolbox – Miscellaneous
OPTION
DEFINITION
MAC Address for Wake on LAN
Enter the MAC address of the computer you would like to wake up from stand-by mode.
Domain Name or IP Address for PING
Test
Enter the domain name or IP address you wish to attempt to ping to.
LED Settings
Select the manually control the LED brightness.
Table 36: Advanced - Toolbox - Miscellaneous
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
61
YML38
www.netcommlimited.com
Logout
The logout option gives the user the option to logout of the NF2 Graphical User Interface.
Figure 68: Advanced - Toolbox - Logout
YML27
www.netcommlimited.com
NetComm NF2 User Guide
62
Additional Product Information
Establishing a wireless connection
Windows XP (Service Pack 2)
1. Open the Network Connections control panel (Start -> Control Panel -> Network Connections):
2. Right-click on your Wireless Network Connection and select View Available Wireless Networks:
3. Select the wireless network listed on your included wireless security card and click Connect.
4. Enter the network key (refer to the included wireless security card for the default wireless network key).
5. The connection will show Connected.
Windows Vista
1. Open the Network and Sharing Center (Start > Control Panel > Network and Sharing center).
2. Click on "Connect to a network".
3. Choose "Connect to the Internet" and click on "Next".
4. Select the wireless network listed on your included wireless security card and click Connect.
5. Enter the network key (refer to the included wireless security card for the default wireless network key).
6. Select the appropriate location. This will affect the firewall settings on the computer.
7. Click on both "Save this network" and "Start this connection automatically" and click "Next".
Windows 7
1. Open the Network and Sharing Center (Start > Control Panel > Network and Sharing center).
2. Click on "Change Adapter settings" on the left-hand side.
3. Right-click on "Wireless Network Connection" and select "Connect / Disconnect".
4. Select the wireless network listed on your included wireless security card and click Connect.
5. Enter the network key (refer to the included wireless security card for the default wireless network key).
6. You may then see a window that asks you to "Select a location for the 'wireless' network". Please select the "Home"
location.
7. You may then see a window prompting you to setup a "HomeGroup". Click "Cancel" on this.
8. You can verify your wireless connection by clicking the "Wireless Signal" indicator in your system tray.
9. After clicking on this, you should see an entry matching the SSID of your NB16WV with "Connected" next to it
Mac OSX 10.6
1. Click on the Airport icon on the top right menu.
2. Select the wireless network listed on your included wireless security card and click Connect.
3. On the new window, select ‚Show Password‛, type in the network key (refer to the included wireless security card for the
default wireless network key) in the Password field and then click on OK.
4. To check the connection, click on the Airport icon and there should be a tick on the wireless network name.
Please note: For other operating system (Windows 98SE, Windows ME, Windows 2000 etc) or if you use a
wireless adaptor utility to configure your wireless connection, please consult the wireless adapter
documentation for additional information.
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
63
YML38
www.netcommlimited.com
Technical Data
The following table lists the hardware specifications of the NF2™ Hub.
MODEL
NF2™ HUB
Wireless WAN
1 x USB 2.0 port for external HSPA modem PPP (for WCDMA / HSPA)
Ethernet WAN
1 x Gigabit WAN port (10/100/1000 Mbps)
Connectivity
USB 2.0 x 2, 10/100/1000 Ethernet LAN x 3,1 x 2.4GHz WLAN,1 x 5.0 GHZ WLAN
Antenna connector
SMA (female connector)
LED Indicators
Power, 3G, WWW, WiFi, WAN, WDS, LAN 1-3
Operating Temperature
0 ~ 50 degrees Celsius (operating temperature)
Power input
12VDC – 1.5A
Dimensions & Weight
133 mm (L) x 137 mm (H) x 34 mm (W)
250 grams
Regulatory Compliancy
C-Tick
Table 38 - Technical Specifications for the NetComm NF2
Electrical Specifications
A suitable power supply is available on request or via direct purchase from the NetComm Online shop. It is recommended that the
NF2™ Hub be powered using the 12VDC/1.5A power supply which is included with the device.
Environmental Specifications / Tolerances
The NF2™ Hub is able to operate over a wide variety of temperatures from 0˚C ~ 50˚C (ambient).
YML27
www.netcommlimited.com
NetComm NF2 User Guide
64
FAQ
1.
Does the Dual Band WiFi Gigabit Hub require any configuration out of the box?
No, the NF2™ Hub is a plug and play device. Plug the device into an electrical outlet and once the status indicator lights
are on, plug in your LAN cable for data connectivity. For WiFi connectivity the default SSID (Service Set Identifier) and
network key (password) are located on the bottom of the device. If you would like to customize your settings you can enter
192.168.20.1 into your Web browser to access the Management Console and device settings.
2.
I cannot seem to access the web page interface.
The default IP address of the unit is 192.168.20.1, so first try to open a web browser to this address. Also check that your
laptop/ PC is using the same subnet as the router’s Ethernet port. I.e. An IP address has been assigned to your computer
in the range of 192.168.20.x where x can equal 2 – 254.
3.
The router has a connection but cannot access the internet
Check that DNS Proxy is enabled by clicking on the Network Setup > DHCP Server page on the configuration interface.
Make sure that the DHCP DNS server address 1 IP address is set to the same address as that of the Ethernet port.
4.
Is the Dual Band WiFi Gigabit Hub secure; can other people access my wireless network?
The Dual Band WiFi Gigabit Hub comes configured with WPA-PSK/WPA2-PSK WiFi security enabled. When you first
access the Internet, type 192.168.20.1 into the address bar, the wizard will pop up to configure your computer to connect
with the wireless security settings of your choice (please see the Quick Start Guide for more information on connecting
your data devices to the Dual Band WiFi Gigabit Hub). Only people you allow access to, will be able to connect to the Dual
Band WiFi Gigabit Hub ensuring your connection is secure and safe.
5.
Can I change the name and password of my wireless network?
Yes. You can change your Dual Band WiFi Gigabit Hub settings from the browser user interface by typing 192.168.20.1
into the address bar of your Web browser. You can change the WiFi network name or SSID (Service Set Identifier), WiFi
security standard (WPA, WPA2, WEP) and your WiFi password.
6.
How do I share my Internet connection, using the Dual Band WiFi Gigabit Hub, with other users?
Provide the SSID (Service Set Identifier) and WiFi network password of your Dual Band WiFi Gigabit Hub for any users you
want to share your WiFi Internet connection with. Each user will need to select the Dual Band WiFi Gigabit Hub SSID, on
their WiFi enabled computer or device and enter the network password you provide.
7.
What is the difference between upload and download speeds and why do they differ?
Upload is when you send information (e.g. emails) from your computer and download is when you receive
information via the Internet. The speeds at which upload and download operate depend on the way you use
the Internet and the size of files you send and receive.
8.
Do I need to attach an antenna on this device?
Yes. Your Dual Band WiFi Gigabit Hub comes equipped with an antenna; you need to attach the WiFi antenna to send and
receive wireless signals.
9.
I have lost the security card that came with the setup instructions. What can I do?
If you have lost your security card, and forgotten the wireless security details (SSID and WiFi network password), there is a
label attached to the base of your Dual Band WiFi Gigabit Hub with all your original security details. If the label is
unreadable or has been removed, the WiFi network password can be viewed or reset by logging in to the
Management Console using an Ethernet Cable connected to the LAN port of the NF2™ Hub.
10. I forgot my Management Console password. What can I do?
If you have forgotten your Management Console password and cannot access the Web user interface, you will need to
reset your Dual Band WiFi Gigabit Hub back to factory default settings. To reset your device press and hold the reset
button on the back of your Dual Band WiFi Gigabit Hub for 10-15 seconds until all the indicator lights on the unit flash to
indicate the device is reset. After a reset, use the default WiFi settings (SSID and WPA key) which can be found on the
base of your Dual Band WiFi Gigabit Hub. (Note - this will also reset any custom settings and passwords you may have
already set up).
11. Can I use the Dual Band WiFi Gigabit Hub overseas?
No. The Dual Band WiFi Gigabit Hub is not equipped for international roaming or data services.
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
65
YML38
www.netcommlimited.com
Appendix A: Tables
Table 1 - Document Revision History ........................................................................................................................... 2
Table 2 - LED Indicators ................................................................................................................................................ 7
Table 4: LAN Management Default Settings ................................................................................................................ 9
Table 5: WAN Port Default Settings.............................................................................................................................. 9
Table 6: WiFi Default Settings....................................................................................................................................... 9
Table 7: Web Interface Default Settings ...................................................................................................................... 9
Table 8: Basic View - Status ........................................................................................................................................19
Table 9: Basic View - 2.4 GHz Wireless Settings .........................................................................................................20
Table 10: Basic View - 5.0 GHZ Wireless Settings .......................................................................................................21
Table 11: Basic View - Mobile Broadband Settings ....................................................................................................22
Table 12 - Advanced View – Ethernet WAN Settings .................................................................................................25
Table 13: Advanced - Network Setup - Wireless WAN ...............................................................................................26
Table 14: Advanced - DHCP Settings ..........................................................................................................................27
Table 15: Advanced Wireless 2.4 GHz Settings ..........................................................................................................28
Table 16: Advanced - WPS Setup settings ..................................................................................................................29
Table 17: Advanced - Network Setup - 5.0 GHz Wireless Settings .............................................................................30
Table 18: Advanced - Network Setup -VPN-IPSec ......................................................................................................31
Table 19: Advanced - Network Setup - VPN IPSec - Dynamic IPSec ...........................................................................32
Table 20: Advanced - Network Setup - VPN - PPTP Server Settings ...........................................................................34
Table 21: Advanced - Forwarding Rules - Virtual Server Settings ..............................................................................36
Table 22: Advanced - Forwarding Rules - Port Triggering Settings ............................................................................37
Table 23: Advanced - Security Settings - Packet Filtering Settings .............................................................................39
Table 24: Advanced - Security Settings - Domain Filtering Settings: ..........................................................................40
Table 25: Advanced - Advanced Settings - System Log Settings ................................................................................43
Table 26: Advanced - Advanced Settings - Dynamic DNS Settings .............................................................................43
Table 27: Advanced - Advanced Settings - QoS Settings ............................................................................................44
Table 28: Advanced - Advanced Settings - SNMP Settings .........................................................................................45
Table 29: Advanced - Advanced Settings - System Time ............................................................................................46
Table 30: Advanced - Advanced settings - Adding a Schedule Settings .....................................................................47
Table 31: Advanced - Advanced Settings – IPv6 Settings ...........................................................................................48
Table 32: Advanced - Advanced Settings - TR-069 .....................................................................................................49
Table 33: Advanced - NAS Settings - File Sharing - FTP Service Configuration ...........................................................52
Table 34: Advanced - NAS Settings - iTunes Server ....................................................................................................54
Table 35: Advanced - NAS Settings - Download Assistant Settings ............................................................................55
Table 36: Advanced - NAS Settings - Download Assistant - Email Alert Settings .......................................................56
Table 37: Advanced - Toolbox - Miscellaneous ..........................................................................................................61
YML27
www.netcommlimited.com
NetComm NF2 User Guide
66
Legal & Regulatory Information
Intellectual Property Rights
All intellectual property rights (including copyright and trade mark rights) subsisting in, relating to or arising out this Manual are
owned by and vested in NetComm Wireless Limited (ACN 002490486) (NetComm) (or its licensors). This Manual does not transfer
any right, title or interest in NetComm’s (or its licensors’) intellectual property rights to you.
You are permitted to use this Manual for the sole purpose of using the NetComm product to which it relates. Otherwise no part of
this Manual may be reproduced, stored in a retrieval system or transmitted in any form, by any means, be it electronic, mechanical,
recording or otherwise, without the prior written permission of NetComm.
NetComm is a trademark of NetComm Wireless Limited. All other trademarks are acknowledged to be the property of their
respective owners.
Customer Information
The Australian Communications & Media Authority (ACMA) requires you to be aware of the following information and warnings:
1. This unit may be connected to the Telecommunication Network through a line cord which meets the requirements of the AS/CA
S008-2011 Standard.
2. This equipment has been tested and found to comply with the Standards for C-Tick and or A-Tick as set by the ACMA. These
standards are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio noise and, if not installed and used in accordance with the instructions detailed within this
manual, may cause interference to radio communications. However, there is no guarantee that interference will not occur with the
installation of this product in your home or office. If this equipment does cause some degree of interference to radio or television
reception, which can be determined by turning the equipment off and on, we encourage the user to try to correct the interference
by one or more of the following measures:
Change the direction or relocate the receiving antenna.
Increase the separation between this equipment and the receiver.
Connect the equipment to an alternate power outlet on a different power circuit from that to which the receiver/TV
is connected.
Consult an experienced radio/TV technician for help.
3. The power supply that is provided with this unit is only intended for use with this product. Do not use this power supply with
any other product or do not use any other power supply that is not approved for use with this product by NetComm. Failure to do
so may cause damage to this product, fire or result in personal injury.
Consumer Protection Laws
Australian and New Zealand consumer law in certain circumstances implies mandatory guarantees, conditions and warranties which
cannot be excluded by NetComm and legislation of another country's Government may have a similar effect (together these are the
Consumer Protection Laws). Any warranty or representation provided by NetComm is in addition to, and not in replacement of, your
rights under such Consumer Protection Laws. If you purchased our goods in Australia and you are a consumer, you are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a
major failure. If you purchased our goods in New Zealand and are a consumer you will also be entitled to similar statutory
guarantees.
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
67
YML38
www.netcommlimited.com
Product Warranty
All NetComm products have a standard one (1) year warranty from date of purchase, however, some products have an extended
warranty option (refer to packaging and the warranty card) (each a Product Warranty). To be eligible for the extended warranty
option you must supply the requested warranty information to NetComm within 30 days of the original purchase by registering
online via the NetComm web site at www.NetComm.com.au. For all Product Warranty claims you will require proof of purchase. All
Product Warranties are in addition to your rights and remedies under applicable Consumer Protection Laws which cannot be
excluded (see Section 3 above). Subject to your rights and remedies under applicable Consumer Protection Laws which cannot be
excluded (see Section 3 above), the Product Warranty is granted on the following conditions:
1. The Product Warranty extends to the original purchaser (you / the customer) and is not transferable;
2. The Product Warranty shall not apply to software programs, batteries, power supplies, cables or other accessories
supplied in or with the product;
3. The customer complies with all of the terms of any relevant agreement with NetComm and any other reasonable
requirements of NetComm including producing such evidence of purchase as NetComm may require;
4. The cost of transporting product to and from NetComm’s nominated premises is your responsibility;
5. NetComm does not have any liability or responsibility under the Product Warranty where any cost, loss, injury or damage
of any kind, whether direct, indirect, consequential, incidental or otherwise arises out of events beyond NetComm’s
reasonable control. This includes but is not limited to: acts of God, war, riot, embargoes, acts of civil or military authorities,
fire, floods, electricity outages, lightning, power surges, or shortages of materials or labour; and
6. The customer is responsible for the security of their computer and network at all times. Security features may be disabled
within the factory default settings. NetComm recommends that you enable these features to enhance your security.
Subject to your rights and remedies under applicable Consumer Protection Laws which cannot be excluded (see Section 3 above),
the Product Warranty is automatically voided if:
1. you, or someone else, use the product, or attempt to use it, other than as specified by NetComm;
2. the fault or defect in your product is the result of a voltage surge subjected to the product either by the way of power
supply or communication line, whether caused by thunderstorm activity or any other cause(s);
3. the fault is the result of accidental damage or damage in transit, including but not limited to liquid spillage;
4. your product has been used for any purposes other than that for which it is sold, or in any way other than in strict
accordance with the user manual supplied;
5. your product has been repaired or modified or attempted to be repaired or modified, other than by a qualified person at a
service centre authorised by NetComm; or
6. the serial number has been defaced or altered in any way or if the serial number plate has been removed.
Limitation of Liability
This clause does not apply to New Zealand consumers.
Subject to your rights and remedies under applicable Consumer Protection Laws which cannot be excluded (see Section 3 above),
NetComm accepts no liability or responsibility, for consequences arising from the use of this product. NetComm reserves the right
to change the specifications and operating details of this product without notice.
If any law implies a guarantee, condition or warranty in respect of goods or services supplied, and NetComm’s liability for breach of
that condition or warranty may not be excluded but may be limited, then subject to your rights and remedies under any applicable
Consumer Protection Laws which cannot be excluded, NetComm’s liability for any breach of that guarantee, condition or warranty
is limited to: (i) in the case of a supply of goods, NetComm doing any one or more of the following: replacing the goods or supplying
equivalent goods; repairing the goods; paying the cost of replacing the goods or of acquiring equivalent goods; or paying the cost
of having the goods repaired; or (ii) in the case of a supply of services, NetComm doing either or both of the following: supplying the
services again; or paying the cost of having the services supplied again.
To the extent NetComm is unable to limit its liability as set out above, NetComm limits its liability to the extent such liability is lawfully
able to be limited.
YML27
www.netcommlimited.com
NetComm NF2 User Guide
68
Contact
Address: NETCOMM WIRELESS LIMITED Head Office
PO Box 1200, Lane Cove NSW 2066 Australia
P: +61(0)2 9424 2070 F: +61(0)2 9424 2010
E: [email protected]
W: www.NetCommlimited.com
NF2 – Dual Band Wi-Fi Gigabit Hub User Guide
69
YML38
www.netcommlimited.com