Download E-70N

E-70N
Used iniectiOn Needie Melting Device
◆ This manual provides instructions to ensure safe use of the
syringe needle melting unit. Please read it thoroughly before
operation.
◆ Please keep this manual nearthe syringe needle melting unit
at a‖tirnes so thatit can be referred to whenever necessary.
INttRODUCttiON
Thank you for purchasing our syringe need!e melting unit.This userls manual describes how
to operate it,and provides instructions which should owed
be fo‖
during operation.
Please keep this rnanualin a safe place,and referto it before use and whenever necessary.
Maior Features
□丁he unitis designed for use with various types of need!es.
The unique fusing system can efficiently process 27G
1 8G‐
type of needles.
□Manages 400 needles with a sing!e charge.
lt can handle 400 of 23G type of need!es with on!y a single battery charge.The processing
tirne per a syringe is at approximate!y2or 3 seconds.(Required 14 hours to recharge the
emp‖ ed battery)
□Removes unpleasant odor.
The exclusive deodorant!iqu:d is attached to this device,and it removes unpleasant odor
when rnelting needles with b!ood etc.
□Compact designed and portable.
carried and used atlocations with no access to
VVith the rechargeable battery,it can bey eas‖
AC powersupply.
□Secured against electromagnetic wave.
The outside of frame is made of Aluminum die‐
cast so that it can prevent from a!eak of
electromagnetic wave which gives a bad inf!uence to patients and other rnedica!devices.
Federal CommunicaJons Commission(FCC)Declaralon of Conformky.
This equipment has been tested and found to comply with the limits for a Class B d:gital
device, pursuant to Part 15 of the FCC Rules.These!innits are designed to provide
reasonab!e protection against harmful interference in a residentia! insta‖
ation.丁his
equipment generates,uses,and can radiate radio frequency energy and,if not:nsta‖
ed and
used in accordance with the instructions, may cause harmfu! :nterference to rad:o
communications. However, there is no guarantee that interference w‖ l not occurin a
particuiar insta‖
ation.lf this equipment does cause harmfulinterference to radio or television
reception, which can be deternlined by turning the equipment off and on,the user is
encouraged to try to correctthe interference by one or rnore ofthe
owing fo‖
rneasures.
◆ Reorient or relocate the receiving antenna.
● lncrease the separation beh″
een the equlpment and receiver.
◆Connectthe equipmentinto an outlet on a circuit differentfrom thatto which the receiveris
connected.
OConsultthe dealer or service representative for he!p
esOftic」apan Co.,Ltd.is not responsible for any radio or te!evision interference caused by
using other than recommended cables or connectors or by unauthorized changes or
modifications to this equipment. Unauthorized changes or modifications cou!d void the
user's authority to operate the equipment This device complies with Part 15 of the FCC
Rules.Operalon is subieCt tO the fo!!owing two condlions:(1)thiS device may not cause
harmful interference,and(2)this device must accept any interference received,inc!uding
interference that may cause undesired operation
Responsib!e party:
Softic」
apan Co.,Ltd.
1‐
4,Koami¨cho,Nihonbashi,chuuou¨ku,Tokyo,103‐0016,Japan
丁elephone:03¨5645‐3500
Copyright 2005 Softic」
apan co.,Ltd,A‖ rights reserved
READ ALL!NSTRUCT10NS BEFORtt US:NG ttHE APPL:ANCE
IMPORTANT SAFEGUARDS
DANGttR‐ To reduce the nsk Of e!ectroculon:
1.Do not use wh‖
e bathing
2 Do notp!ace or store product where it can or
fa‖
be pu‖
ed into a tub or sink
quid.
3.Do not place in or drop into water or other‖
4 Do not reach for a productthat has en
fa‖
into water.
WARNING‐ To reduce the nsk Of burns,electroculon,lre,oriniury to persons.
l Close supervision is necessary when this product is used by, on, or near
children orinva!ids.
2.Use this product only for lts intended use as described in th:s manua!. Do
not use attachments notrecommended by the manufacturer.
3.Never operate this product if it has a damaged cord or p!ug, if it is not
working properly,ifit has been dropped or damaged,or dropped into water.
Return the productto a service centerfor examination and repair.
4.Never block the air openings of the product or place it on a soft surface,
such as a bed or couch,where the air openlngs may be b!ocked.Keep the
air opening free of!int,ha:r,and the!lke.
5.Never drop orinsert any ouectinto any opening or hose
6.Do not use outdoors or operate where aerosol(spray)prOducts are being
used or where oxygen is being administered.
SAVtt THES匡 :NSttRUCT!ONS
▲WARNING
▲ CAUT10N
VVARNING‖ signs during operation may result in
F a ‖u r e t o h e e d ‖
senOus iniury or death.
10N‖signs during operation may resultin serious
Failure to heed‖
CAU￢「
in,ury.
Positionlng and Power Supply
∪se the charger attached to the unit Be sure
that the power supply voltage complies with
Do not put the unit in an unstable place lf it
the rating marked on the unit Use of a wrong
should fa‖, personal iniury or damage to the
power supply voltage may result in fire,
unit may result.
electric shock or destruction of the device.
Do not connectthe power cable to an adapter
Make sure that there is no dust or foreign
connecting numerous cab!es, and do not
matter on the unit side charge adapter
rework the cable. Do not put heavy obleCtS
terminal and the DC output plug on the
on the power cable or heat or pu‖ it Fire or
attached adapter Fu‖y insert the DC output
electric shock may result
plug into the unit side Loose connection may
result in fire or electric shock
①乙 σ
Do not put anything otherthan syringe needles
Device Use
into the syringe needle inlet. lf meta:s or
Do not remove, disassemb!e, or recondition
‖
ammable ouects are entered,lre,damage,
the cover on the unit. Fire, electric shock,
personal iniury or marunc10n may result lf
personaliniury or marunc10n may resun.
foreign ouects are entered by mistake,turn off
the power switch and stop the unit
Do not put hands or foreign obieCtS into the
When disposing of syringe needles, be sure
unit through the dust box tray in!etlectric
E二
that there is no flammable obleCt near the
shock,iniury or damage to the unit may
unit, and that there is no !eakage of
result.
combustible gas Do not use the unit in a
room where combustible gas may be
produced as this will resu!tin an explosion.
Be sure that syringe need:es comp!y with the
The unit should not be used if there is a
specifications :f too long a needle for the
possibillty that a syringe contains liquid which
syringe needle inlet is entered, electronic
can produce volatile toxic substances.
devices in the vicinity may be affected by
Poisoning may result
spark discharge
OC勁
!V
Table of contents
Part Names and Funclons・
・・・・。(1)
Basic Functions・ ・・・・・・・・・・・・。(2)
・… … 。(4)
:nieCtiOn Needle Fusing…
Before Operalon… ・… ・… ・… ・・(4)
Operalon…
… ・… ・… ・… 。… … (5)
Battery Charging 。・・・・・・・・・・・。(7)
C!eaning・・・・・・・・・・・・・・・・・・。(3)
Fo‖ow the instructions below for
storing the unit・・。(8)
Dust Box・・・・・・・・・・・・・・・・・・・(9)
Specifications ・・・・・・・・・・・・・・(10)
Battery check lamps
indicate remaining battery power
TO carry the unit
needle inlet
Supports syringes
Syringe needle lnlet
Connects to the DC output
plug ofthe charge adapter
Power swlch
To turn power on/off
Dust box tray
Tray containing dust box
For rne:ted syringe needles
Basic Functions
Explanation of unitis basic functions
Handle
Hold the handle firmly when carrylng the unit
When putting the unit down, take care not to
cause impact.
Power Swlch
Forturning power on and off.
ON:The battery check lamps on top ofthe unlt
light to indicate that the unitis ready for use.
OFF:The unit cannot be used.
Power Swnch:The Automalc Off
y turned
The power switch may be automatica‖
off for safety. ln either of the
fo‖cases,
owing
power will not come on or will be automa‖ cally
turned off:
●Abnormality is sensed in the electric current
used for operation.
OThe dust box tray ls not set properly.
Battery Check Lamps
丁he remaining battery power is shown by the
indicator on top ofthe unit
Red Green Green
(1)●
● ● :Fu!ly charged
(2)●
●
○ :Mening pOSSible
(3)●
○
○ :Batery charging necessary
When status(3)is indiCated, stop the unit
irnrnediateiy and recharge the batteries (See
battery charging on page 7.)
(2)
Charging Adapter Terminal
VVhen charging the batteryl connect the charge
adapter(See battery charging on page 7.)
Dust Box Tray
Metallic scraps d:scarded ounng mehing are
contained in a dust box which is held in the dust
box tray.
Oif waste:n the dust box reaches the red line,
dispose the scrap only.
(3)
Before Operation
Before use,check the fo‖ owing:
1)The dust box is properly fixed to the dust box
tray
2)Check that the waste levelin the dust box is
below the red line.
The dust box tray is properly closed
丁he thickness,!ength and shape of syringes and
syringe need:es comp!y with the specifications
(See Specifications on page 1 0)
▲ WARN:NG lniec10n‖
purged from syringe
(4)
quid and blood must be
Operation
l f t h e硼雨e m お り山∝‖a m p ぃ
:o"∝
酬 山m g 酬
鴫 d"mm“
ndy ttd char"
the battery.丁
o carry out rne!ting,fo‖
ow the procedure below:
1)丁urn on the powerswnch
ecOnfirm thatthe battery check‖ ghts are on.
2)Ho!d the syringe fitted with a need!e vertlca‖
y
above the unit,and feed itinto the in!et s!owly.
3)Ensure that the syringe blocks the syringe
needle inlet hole completely
(5)
4)Depress the syringe needle in!et plate s!owly,
with the syringe,until lt stops.
The need!e is now being melted
During melting the light of electrical discharge
may be visib!e through the inlet plate
▲C A U T : O N D o n o t r d e a s e t h e s y n n 9 e d u n n
mening,as this may resun in burns Oriniury
NOTE: Push the plate down slowly with the
syringe,for about three seconds until it stops
For a need!e thicker than 23G,take more tirne
(fOr eXample,about five seconds)when pushing
the plate down.
Performing this operation in less time will not
result in proper rnelting.
nge
5)When mening is lnished,withdraw the sy‖
slowly.
▲C A U T : O N s y r i n g e n e e d ! e s a r e c u t a t a
imeters from their root.
distance of several mi‖
The roots ofthe needles will be heated to a high
l result in
temperature. Do not touch as this w‖
iniury or burns
6)After complelon of mening,wan thirty seconds
before switching off.
▲C A U T 1 0 N D o n o t s w n c h o f f a t c o m t t e l o
meltlng Gas and odors produced during meiting
wi‖remain inside the unit.Their remova:requires
at least thirty seconds
OFF―
→ ON
(6)
lfthe middie battery check lamp 9oes out during rnelting,stop imrnediate!y and charge the battery
聞 l u r e t o t t s 酬 Ю釧 旧 n n e e d ∝ 田 ∞ 而 「叩 酬 y m e l t “0 ↑
∝
Du‖ng charging the!eft hand red lightis lt to indicate charging in progress(●○ ○)
On complelon of charging this‖ ght wil!go out(○ ○ ○).
Fu‖charge tirne is approximately twelve hours
Fu‖charge is recommended to have a longer battery!ife
Battery Charging
丁he battery charging procedure is asows:
fo‖
1)Turn Offthe power swnch On the mening unl.
OFF―
→ ON
2)ConneCt the DC output plug on the charge
adapter to the charge adapter terminal on the
unit.
!nsertthe AC plug into the AC plug receptacle
l light
The left hand red battery check lamp w‖
d u n n g c h a r g i n g ( ●○ ○) .
y charged,this iamp wi!￨
VVhen the battery is fu‖
g o o u t ( ○ ○ ○) .
N()TE:The operation ofthe unitis possible even
︵ 一
during charging.
m剖
h8inЪ
C8rgeぶ
_〔
ざ
〔 〕
(7)
丁he enclosure surface, dust box tray, and other parts of this equipment wil!
become dirty as this equipment is used for long. When they become dirty,
clean them as shown be!ow
l)丁 urn the power swnch Off Disconnect DC output plug of Charge adapter
from Charge adapterterminal.
2)Wipe dirty parts:ightly with gauze or soft cloth moistened with neutral
detergent diluted with water or a!cohol.
3)Moisten cioth lightly by hand lf the cloth is soaked with too much detergent
or alcohol,the enclosure surface remains wet after cleaning and residual
detergent or alcohol may penetrate into the product,causing damages to
interna!parts.
4)After wiping,leave it until lt dries completely.Do not attempt to turn on the
powerimmediately after wiping.
5)Never use thinner or organic so:vent.
1)Pu‖ Outthe dust box,then store the dust box and the unit separately.
2)Charge the battery for more than 12 hours every three months when the unl
ls not used for a long tirne
3)Keep the unitin the p!ace without direct sun light.
(8)
Before commencing me!ting,check that the waste leve!is below the red line in the dust box lf the
red line has been reached,dispose the scrap only.
1)Turn Offthe power swnch
2)Pu‖ outthe dust box tray.
3)Dispose the scrap only.
▲ WARNING After mening,waste and iniec10n
liquid will be presentin the dust box Such matter
is very dangerous and should not be touched by
hand under any circumstances.
NOTE:
匡nsure that the dust box lid is open
properly.
0!f the dust box is not set proper!y,the power
switch cannot be turned on.
4)匡 nsure that the dust box tray is completely
pushed in(unti:it stops).
N()TE:lfthe dust box tray is not set properly,the
power switch cannot be turned on
(9)
ltems
Specificat:ons
▲ lndoor use On!y.
This equipment sha‖ be used indoor only.
Operation tirne
Approx.3 seconds(For a 23G,linch need!e)
Applicable
Syr:nge needles
丁hickness:16G to 30G
O Standard plate:needle!ength o.5‐
1.5 inch
Syrlnge diameter O.26‐
1.18 inch
Power supply
Battery(charging depends on charge adapter)
!nsta‖
ation category
Ⅱ
Po‖ution degree
2
Anitude
Up to 2000m (6560 feet)
Charge Adapter
AC 120V(+55%,‐
!nput
9V==
Battery
淵孵‖
::亀
γ
硝愧ξ
魂1計check
1:‖
は
RIЪ
麗臨M∫
155%)60Hz
抑0
i轍鸞濶 :聯糊ゎ
Fuse
(Fl)T2A/125V;(F2)丁
Dust Box
Replace at about 2000 23G linch needles(conSumables)
Operating
environment
40℃ ★
・Temperature:5℃ ‐
3A/125V ser宙 Ceman replace only
★
35℃
も
a ma劇
mumbmpttuЮ
du‖
ng battew chaun⊆
・Humid“ y:20%‐ 80%RH(at 25
Lifespan
5 years or 300,000 23G linch needles,whichever rnay be earlier
(eXCepting the battery)
Dimenslons
7.87X7.75X6.69 inch(WxDXH)
Weight
Unit,5kg;charge‐ adapter,o6kg
Accessorles
Userls rnanual,Charge adapter,dust box
Term of warranty
1(One)year
After about a 1 2 hour battery recharging period,the unit can melt approx.400 of 23G linch
syringe needles.
The fo‖
owing types of syringe with the above applicable syringe needles can be operatedi
normal syringe, and tubercu‖
n syringe. Butterfly‐
winged syringe, blood co‖
e ction syringe,
denta:syringe and other special syringes are not applicable forthis unit
(10)