1
Download TX66-22 - Genie Industries
Transcript
OPERATOR HANDBOOK Code 57.0004.9200 - Rev.0 09/2004 Handler with telescopic boom TX 66-22 English Edition CAUTION: THOROUGHLY READ AND UNDERSTAND THIS HANDBOOK BEFORE OPERATING THE MACHINE CAUTION: KEEP THIS HANDBOOK IN THE MACHINE AT ALL TIMES ZONA INDUSTRIALE I-06019 UMBERTIDE (PG) - ITALY Tel. +39 075 941811 - Fax +39 075 9415382 Technical Assistance Service Tel.: +39 075 9418125 +39 075 9418129 +39 075 9418171 e-mail: [email protected] DEALER’S OR ASSISTANCE CENTRE STAMP Operator Handbook 57.0004.9200 - TX 66-22 All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means without prior written permission from TEREXLIFT srl. In pursuing a policy of constant quality improvement, TEREXLIFT srl reserves the right to make changes at any time and without undertaking to give prior notice; therefore, also this publication may be subject to modifications. Some photos or drawings have been used to illustrate a specific function; as a result, they may not refer to the machine treated in this manual. © Copyright 2004 TEREXLIFT srl - All rights reserved. Produced by: LIST OF REVISED PAGES Revision No. date 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Revised pages Notes Issued by Handler with telescopic boom TX 66-22 INTRODUCTION ■ INTRODUCTION Sections are subdivided into chapters and paragraphs that are numbered progressively. This handbook provides information for a safe and proper operation and maintenance of the machine. STRICTLY COMPLY WITH THE INSTRUCTIONS GIVEN IN THIS HANDBOOK! READ AND UNDERSTAND THIS HANDBOOK BEFORE STARTING, USING AND CARRYING OUT ANY OPERATION WITH AND ON THE MACHINE. The quickest way to look for an information is the reference to the general index or the titles of the single chapters and paragraphs that represent keys for an easy consultation. Take care of this handbook and keep it in an accessible place within the machine, even after its reading, so that it will always be within reach if in doubt. The handbook is divided into seven sections: Sect. Sect. Sect. Sect. Sect. Sect. Sect. A B C D E F G GENERAL INFORMATION SAFETY OPERATING INSTRUCTIONS MAINTENANCE TROUBLESHOOTING OPTIONAL ATTACHMENTS TABLES AND ENCLOSURES If you are unsure about anything, please address to TEREXLIFT Assistance Service or to your agent/ dealer: addresses, phone and fax numbers are printed in the cover and in the title-page of this manual. Section A contains general concepts that are decisive for the knowledge of the main parts of the machine. It also contains all necessary data for a correct identification of the machine, the technical features of the machine, etc. Section B is especially addressed to the personnel, who shall operate, repair and service the machine, and, in case of companies with a wide fleet of machines, to the safety responsible. It describes the essential compulsory qualities of the personnel in charge and other important information for the safety of persons and things. IMPORTANT Any difference between the contents of this manual and the real functional character of the machine can be attributed to either a machine manufactured before the issue of this manual or to a manual going to be updated after some changed effected on the machine. Always contact Terexlift Assistance Service for any updated version of this manual and any additional information. Section C is mainly addressed to the operators who operate the machine. This section illustrates all control devices. Additionally, it contains the main use instructions -i.e. engine starting, machine parking, machine storing. Section D is addressed to the maintenance responsible and the servicemen. The section describes the maintenance schedule and the relevant intervals. Section E deals with the failure diagnostics. Section F makes a list of the main interchangeable attachments that can be coupled to the machine: dimensions, weight, application field and limits of use. Section G contains tables and various enclosed documents like load charts, wiring diagrams, hydraulic schemes, torque wrench setting table, etc. Page 1 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 INTRODUCTION ■ SYMBOLS When using the machine, operators could have to face some situations requiring special care and particular knowledge. When these situations involve the safety of operators or bystanders, the machine efficiency and proper utilisation, this handbook stresses these specific instructions by means of SPECIAL SYMBOLS. There are six special (or safety) symbols in this manual, always combined with keywords that class the situations according to their danger degree. The symbols are always followed by a text explaining the situation taken into account, the attention to be paid to such situation, the method and the behaviour to be adopted. When necessary, it stresses prohibitions or supplies instructions to prevent dangers. ATTENTION Draws the attention to situations that involve the machine efficiency. IMPORTANT Draws the attention to important technical information or practical advice that allows for a safer and more efficient use of the machine. PROTECT THE ENVIRONMENT Sometimes, it can be followed by illustrations. We list below the special (or safety) symbols according to the relative seriousness of the hazard situation: Draws the attention to important environmentrelated information. DANGER WHEN READING THIS MANUAL, PAY THE GREATEST ATTENTION TO THESE SPECIAL SYMBOLS AND THE EXPLANATION OF THE SITUATIONS THEY EMPHASIZE. Draws the attention to situations that involve your own as well as the others’ safety and that can result in serious or lethal injury. The manual in electronic format also contains the following symbol: ELECTRICAL DANGER which enables the user to return to the table of contents Draws the attention to situations that involve your own as well as the others’ safety and that can result in serious injury or lethal injury. CAUTION Draws the attention either to situations that involve your own as well as the others’ safety and that can result in minor or moderate injury or to situations that involve the machine efficiency. Page 2 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 GENERAL INDEX GENERAL INDEX GENERAL INFORMATION Sect. A SAFETY Sect. B OPERATING INSTRUCTIONS Sect. C MAINTENANCE Sect. D TROUBLESHOOTING Sect. E OPTIONAL ATTACHMENTS Sect. F TABLES AND DOCUMENTS ENCLOSED Sect. G Page 3 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 Intentionally blank page Page 4 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 GENERAL INFORMATION Section A GENERAL INFORMATION TABLE OF CONTENTS A-1 A-1.1 A-1.2 A-1.2.1 A-1.3 A-2 A-2.1 A-2.2 A-2.3 A-2.4 A-2.5 A-3 A-3.1 A-3.2 A-3.3 A-3.4 A-3.5 A-4 A-4.1 A-4.2 A-4.3 A-4.4 A-5 A-5.1 A-5.2 A-5.3 A-5.4 A-5.5 A-5.6 A-5.7 A-5.8 A-5.9 A-5.10 A-6 A-7 A-7.1 CONVENTIONAL REFERENCES ................................................................................ Machine position ........................................................................................................ Labels and warning plates applied on the machine ................................................... Position ....................................................................................................................... Explanation of the different symbols used on the machine ....................................... MACHINE IDENTIFICATION ....................................................................................... Machine model and type ............................................................................................ Manufacturer .............................................................................................................. Machine identification plates ...................................................................................... Chassis serial number ................................................................................................ Identification plates of the main parts ........................................................................ ALLOWED USE .......................................................................................................... Allowed use ................................................................................................................ Improper use .............................................................................................................. Residual hazards ........................................................................................................ Applicable standards .................................................................................................. Safety devices ............................................................................................................ GENERAL DESCRIPTION .......................................................................................... List of the main components ...................................................................................... Description of the main components ......................................................................... Optional accessories .................................................................................................. Kits supplied on request ............................................................................................. TECHNICAL DATA AND PERFORMANCE ................................................................. Main dimensions ........................................................................................................ Restrictions of use ...................................................................................................... Weight ........................................................................................................................ Speed ......................................................................................................................... Payload and reach ...................................................................................................... Forks ........................................................................................................................... Diesel engine .............................................................................................................. Electrical system ........................................................................................................ Machine sound levels ................................................................................................. Vibration levels ........................................................................................................... LIFETIME .................................................................................................................... ITEMS SUPPLIED ....................................................................................................... Literature supplied ...................................................................................................... Page A-1 Document 57.0004.9200 - Rev. 0 - 09/2004 A-2 A-2 A-3 A-3 A-6 A-8 A-8 A-8 A-8 A-9 A-9 A-10 A-10 A-10 A-10 A-11 A-12 A-13 A-13 A-14 A-14 A-14 A-15 A-15 A-15 A-15 A-15 A-16 A-16 A-16 A-16 A-16 A-16 A-17 A-17 A-17 Handler with telescopic boom TX 66-22 GENERAL INFORMATION A-1 CONVENTIONAL REFERENCES ■ A-1.1 MACHINE POSITION Conventionally the machine should be considered positioned as shown in the figure. This convention is necessary to make any reference of this handbook to different machine parts (front, rear, etc.) clear and unmistakable. Any exception to this rule will always be specified. UPPER PART REAR PART RIGHT SIDE FRONT PART LEFT SIDE LOWER PART Page A-2 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 GENERAL INFORMATION ■ A-1.2 LABELS AND WARNING PLATES APPLIED ON THE MACHINE This paragraph lists the labels and warning plates normally applied on standard machines or on special attachments coupled to the machine. IMPORTANT The familiarisation with these labels is never a waste of time. Make sure they are easy to read. For this purpose, clean them or replace those that become unreadable (either graphic or text). To clean labels, use of a soft cloth, water and soap. Never use solvents, petrol, etc. When a label is applied on a part to be replaced, make sure that the replaced part is already labelled as required or apply a new label. ■ A-1.2.1 Position s.r.l. Zona industriale - 06019 - Umbertide ( PG ) - Italy MODEL NUMBER SERIAL NUMBER YEAR OF MANUFACTURE UNLADEN TRUCK MAXIMUM WEIGHT lb TRUCK CAPACITY lb THIS TRUCK IS COMPLIANT TO PART III OF ASME B56.6-2002 WHERE APPLICABLE MADE IN ITALY 09.4616.0101 09.4618.0109 09.4618.0109 09.4618.0109 09.4618.0109 09.4618.0109 09.4618.0271 Staccabatteria Batterie trennen Battery cut-out switch Coupe-batterie Disyunctor baterìas Destaque bateria Uitsluiten accu 09.4618.0109 09.4618.0271 09.4618.0416 09.4618.0109 Page A-3 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 GENERAL INFORMATION HYDRAULIC OIL 09.4616.0051 01234567 Death or Serious Injury can result from handling of personnel with this machine. 97673 Never equip machine with any form of personnel platform or allow personnel to ride on attachment. F 97673 A 09.4618.0496 N R 09.4618.0389 09.4616.0052 STEERING SELECTION 09.4618.0397 DANGER WARNING 09.4618.0434 Explosion / Burn Hazard WARNING Will cause death, burns or blindness due to ignition of explosive gases or corrosive acid. Burn Hazard Crush Hazard Explosion / Burn Hazard Keep all open flames and sparks away. Wear personal protective equipment, including face shield, gloves and long sleeve shirt. Burns may result from contact with hot surfaces. Do not touch. Allow surfaces to cool before servicing. Moving parts can crush or cut causing severe injury. Release of hot pressurized fluids can cause Burns or Blindness. Consult operation and maintenance manual for jump starting instructions. Keep all body parts clear of moving parts during equipment operation Allow system to cool and always open carefully. 97671 A 97664 A 97675 A 97667 A 97667 97671 97675 97664 WARNING Burns may result from contact with hot surfaces. 97667 Do not touch. Allow surfaces to cool before servicing. 09.4618.0205 97667 A WARNING Crush Hazard Moving parts can crush or cut causing severe injury. Keep all body parts clear of moving parts during equipment operation 60 ° 80° Burn Hazard ° 40 0° 20° 97664 97664 A 09.4618.0451 TX6622 ........ WARNING 09.4618.0010 09.4618.0010 VIETATO APRIRE CON MOTORE IN MOTO DO NOT OPEN WHILE ENGINE IS RUNNING N'OUVRIR QU'A L'ARRET DU MOTEUR ÖFFNEN NUR BEI STILLSTEHENDEM MOTOR ABRIR SOLO CON MOTOR PARADO PROIBIDO ABRIR COM O MOTOR LIGADO VERBODEN KOFFERBAK TE OPENEN WANNEER DE MOTOR DRAAIT Skin Injection Hazard Escaping fluid under pressure can penetrate skin and could cause death or serious injury. Keep away from leaks and pin holes. Use a piece of cardboard to search for leaks. Do not use hands. 82558 A 09.4618.0071 09.4618.0071 82558 WARNING Crush Hazard Moving parts can cause Death or Serious Injury. P= 4 bar P= 97668 Keep clear of elevated components. 4 bar Support components before performing service. Crush Hazard Moving parts can crush or cut causing severe injury. 97665 09.4618.0109 Keep all body parts clear of moving parts during equipment operation 97664 A 97674 A 97674 97664 (top of chassis) (boom rest) WARNING WARNING Electrical Hazard Overturning Hazard Death or serious injury can result from contacting electric power lines. Death or Serious Injury can result from overturning forklift. Always contact the electric power line owner. The electric power shall be disconnected or the power lines moved or insulated before machine operations begin. 97676 Power Line Voltage 0 to 50 kV 50 to 200 kV 200 to 350 kV 350 to 500 kV 500 to 750 kV 750 to 1000 kV • Never exceed published capacity or extend load beyond load chart band. • Never lower maximum load before retracting boom. • Do not travel on terrain or in areas that could cause machine to overturn. Required Clearance 10 ft / 3.03 m 15 ft / 4.60 m 20 ft / 6.10 m 25 ft / 7.62 m 35 ft / 10.67 m 45 ft / 13.72 m • Always level machine using sway control before raising boom above horizontal. • Carry loads so maximum machine stability is maintained. 97676 A 97668 A Always Use Seat Belt Death or Serious Injury can result from failure to wear seat belt. This machine is equipped with a Roll Over Protection System (ROPS). Always adjust seat and fasten seat belt before starting engine. 97665 A WARNING 97670 WARNING Falling Object Hazard Death or Serious Injury can result from falling objects. Crush Hazard Crush Hazard An unattended machine can move or roll. Set park brake, lower carriage or attachment to ground before leaving machine. Failure to heed could result in Death or Serious Injury. Death or Serious Injury can result from people riding on this machine other than at the operator's station. No passengers are permitted to ride on this machine or any attachment. Read and understand operator's manual and safety signs before using or maintaining machine. If you do not understand the information in the manuals, consult your supervisor, the owner or the manufacturer. • Do not operate machine while people are under or near elevated boom whether boom is loaded or unloaded. • Always remain completely within the canopy enclosure while operating machine. 97669 A 97666 A Only operate this machine from the operator's station. 97670 A 97672 A 09.4618.0416 97672 97666 97669 97688 97664 WARNING WARNING Crush Hazard Moving parts can crush or cut causing severe injury. 97688 A Keep all body parts clear of moving parts during equipment operation Keep all body parts clear of moving parts during equipment operation 97664 A 97664 A 09.4618.0071 P= Page 97664 Emergency Exit Handle Crush Hazard Moving parts can crush or cut causing severe injury. A-4 Document 57.0004.9200 - Rev. 0 - 09/2004 4 bar 09.4618.0071 P= 4 bar Handler with telescopic boom TX 66-22 GENERAL INFORMATION Code Description 82558 Fluid at pressure 97664 Risk of crushing hands 97665 Safety belts 97666 Read the user’s manual 97667 Risk of burns and scalds 97668 Risk of overturning 97669 Risk due to falling objects 97688 Emergency exit handle 97670 Risk of crushing 97671 Risk of explosion / burns 97672 Risk of crushing 97673 Prohibition to lift people 97674 Risk of crushing 97675 Risk of explosion / burns 97676 Electrical hazard 00000 Sticker: "TX6622" 09.4616.0051 Hydraulic oil 09.4616.0052 Steering selection 09.4616.0101 Machine data plate 09.4618.0010 Prohibition to open with the engine running 09.4618.0071 Tyre inflation pressure 09.4618.0109 Sticker with various warnings 09.4618.0205 Boom tilting degree 09.4618.0271 Battery cutout switch 09.4618.0389 Control lever controls 09.4618.0397 Terex logotype 09.4618.0416 US flag 09.4618.0434 Terex brand 09.4618.0451 Terex brand-logotype 09.4618.0496 Load chart Page A-5 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 GENERAL INFORMATION ■ A-1.3 EXPLANATION OF THE DIFFERENT SYMBOLS USED ON THE MACHINE This paragraph illustrates those symbols that are normally applied on the main control devices and instruments of a standard machine, and those that can be applied on accessories or special attachments. They are mainly (ISO) standardised symbols that are now part of the common life. But we consider useful to explain them once again. Symbol Description IMPORTANT Spend the necessary time to become familiar with these symbols and to learn their meaning. Symbol Description Steering mode switch Hazard warning lights Engine oil pressure Windscreen wiper Boom up Windscreen washer Boom down Cab ventilation fan Boom out Fuel gauge Boom in Hydraulic oil temperature Attachment locked Position lights Attachment unlocked High beam Turn signals Fork pitching forward Parking brake Fork pitching back Battery charge Oil filter clogged Air filter clogged Glow plug preheating Page A-6 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 GENERAL INFORMATION Symbol Symbol Description Description Front (optional) work light Lifting point Fuel plug Engine oil filler Continuous flow selector Pushbutton enabling the attachment coupling/release Horn pushbutton Mechanical gear selector Warning light - gear put Page A-7 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 GENERAL INFORMATION A-2 MACHINE IDENTIFICATION IMPORTANT Check that the operator handbook refers to the delivered machine. When asking for information or technical assistance, always specify model, type and serial number of the machine. ■ A-2.1 MACHINE MODEL AND TYPE Handler with telescopic boom: ❑ model TX 66-22 ■ A-2.2 MANUFACTURER TEREXLIFT srl Zona Industriale (Ind. Estate) - I-06019 UMBERTIDE (PG) - ITALY Enrolled in the register of companies at the Court of Perugia under no. 4823 C.C.I.A.A. n° 102886 Fiscal Code/V.A.T. no. 00249210543 Zona Industriale - 06019 - Umbertide (PG) - Italy MODEL NUMBER SERIAL NUMBER YEAR OF MANUFACTURE ■ A-2.3 MACHINE IDENTIFICATION PLATES Machine data plate. At the front, on the right side of the chassis. The identification plate contains the main identification data of the machine like model, serial number and year of manufacture. UNLADEN TRUCK MAXIMUN WEIGHT Lb TRUCK CAPACITY Lb THIS TRUCK IS COMPLIANT TO PART III OF ASME B56.6 - 2002 WHERE APPLICABLE MADE IN ITALY Page A-8 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 GENERAL INFORMATION ■ A-2.4 CHASSIS SERIAL NUMBER The chassis serial number is punched on the front left part of the chassis side member. ■ A-2.5 IDENTIFICATION PLATES OF THE MAIN PARTS The plates of the main components, not directly manufactured by TEREXLIFT srl (for instance, engines, pumps, etc.), are located where originally applied by the manufacturers. Page A-9 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 GENERAL INFORMATION A-3 ALLOWED USE ■ A-3.1 ALLOWED USE The handlers have been designed and manufactured for lifting, handling and transporting agricultural or industrial products by means of specific attachments (see section F) manufactured by TEREXLIFT srl. Any other use is considered contrary to that established and, therefore, improper. The compliance with and the strict respect of the operation, maintenance and repair conditions, indicated by the Manufacturer, represent an essential part of the allowed use. The handler must be used and serviced only by operators knowing its characteristics and the safety procedures in depth. It is also essential to comply with the safety at work legislation, the precautions concerning safety and industrial medicine as well as the local and national road traffic regulations. ATTENTION Effecting changes or carrying out interventions on the machine other than those of routine maintenance is expressly forbidden. Any modification of the machine not carried out by TEREXLIFT or an authorised assistance centre involves the automatic invalidation of the conformity of the machine to the Directive 98/37/ EC. ■ A-3.2 IMPROPER USE Improper use means a utilisation of the handler following working criteria that do not comply with the instructions of this manual, and that, in general, may result in risks for both operators and bystanders. DANGER We list below some of the most frequent and hazardous situations of improper use: Carrying passengers on the machine Not strictly complying with the operation and maintenance instructions of this handbook Working beyond the handler working limits Working on unstable edges of ditches Driving crosswise on slopes or hills Working during a storm Working on steep slopes Using attachments other than those recommended Using attachments not approved or directly manufactured by Terexlift Working in potentially explosive areas Working in confined and non-ventilated environments. ■ A-3.3 RESIDUAL HAZARDS Although the machine has been designed and manufactured according to the latest technology and all expected hazards have been eliminated, some operations performed by the machine operator can result in potentially hazardous situations. Among them: • Hazards deriving from a too high work or transfer speed in relation to the load handled or the ground condition of the jobsite. • Hazards deriving from work procedures adopted during the check or replacement of a block valve (residual pressure - uncontrolled movements). • Hazards deriving from work procedures adopted while disassembling parts of the machine -e.g. the cylinders, without supporting mobile parts suitably (risk of uncontrolled fall of the mobile part). • Hazard deriving from an accidental overturning of the machine in the event the operator has not fastened the safety belts. Page A-10 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 GENERAL INFORMATION ■ A-3.4 ISO 6055:1997 High-lift rider trucks - Overhead guards - Specification and testing. For the operator’s safety, the following standards were obeyed during the risk assessment of the handler fitted with telescopic boom: ISO 6292:1996 Powered industrial trucks and tractors - Brake performance and component strength. Directive Title ISO 9533:1989 98/37/CE 89/336/CEE 2000/14/CE Machinery Directive Electromagnetic compatibility Environment Acoustic Emissions Earth-moving machinery - Machinemounted forward and reverse audible warning alarm - Sound test method. Standard Title EN 1459:1988 Harmonised standard. Safety of industrial trucks - Self- propelled variable reach trucks. APPLICABLE STANDARDS prEN 13059:1997 Safety of industrial trucks - Test methods for measuring vibration EN 281:1988 Self-propelled industrial trucks sit- down rider-controlled. Rules for the construction and layout of pedals. EN 292-1:1991 Safety of machinery. Basic concepts, general principles for design. Basic terminology, methodology. EN 292-2:1991 Safety of machinery. Basic concepts, principles for design. Technical principles and specification. EN 1175-2:1998 Electrical requirements - General requirements of internal combustion engine powered trucks EN 50081-1: 1997 Electromagnetic compatibility – Generic requirements on emissions - Part 1 EN 50082-1: 1997 Electromagnetic compatibility – Generic requirements on immunity - Part 1 EN 60204-1:1998 Safety of machinery - Electrical equipment of machines - Part 1 ANSI/ASME B56.6-2002 part III where applicable. prEN ISO 13564:1996 Test method for measuring visibility from self-propelled trucks. ISO 2330:1995 Fork-lift trucks - Fork arms - Technical characteristics and testing. ISO/DIS 3287 Powered industrial trucks. Pictorial signs. Control symbols. ISO 3449:1992 Earth-moving machinery - Falling-object protective structures - Laboratory tests and performance requirements. EN 13510: 2002 Earth-moving machinery - Roll-over protective structures - Laboratory tests and performance requirements. ISO 3776:1989 Tractors for agriculture - Seat belt anchorages. ISO 3795:1989 Road vehicles, tractors and machinery for agriculture and forestry Determination of burning behaviour of interior materials. ISO 5053:1987 Powered industrial trucks - Terminology. Page A-11 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 GENERAL INFORMATION ■ A-3.5 SAFETY DEVICES • The machine is equipped with a negative brake on the front axle which engages automatically when the engine stops. When this brake is disengaged, the engine startup is inhibited. • Block valves fitted to all cylinders: A B C D E Block valve on attachment coupling cylinder Block valve on lifting cylinder Block valve on balance cylinder Block valve on boom extension cylinder Block valve on attachment pitching cylinder Page A-12 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 GENERAL INFORMATION A-4 GENERAL DESCRIPTION ■ A-4.1 LIST OF THE MAIN COMPONENTS � � - � � � � � 1 2 3 4 5 6 7 8 9 10 11 12 � � 쐅 쐈 Forks Attachment holding frame 2nd boom section 1st boom section Engine hood Driving cab Left rear view mirror Front axle Chassis Left front wheel mud-guard Left front wheel reduction gear Left rear wheel reduction gear Page A-13 Document 57.0004.9200 - Rev. 0 - 09/2004 쐉 Handler with telescopic boom TX 66-22 GENERAL INFORMATION ■ A-4.2 DESCRIPTION OF THE MAIN COMPONENTS Hydrostatic transmission This unit consists of parts which drive the machine shifting, and namely: - a variable displacement pump connected to the thermal engine by an elastic joint - a motor with variable displacement and automatic adjustment in relation to the wheel torque required; it is directly installed on the front axle together with the two-speed gearbox - a hydraulic oil filter, placed on the injection line from the tank - a heat exchanger to cool the circuit down. Motion is transmitted to the rear axle from the gearbox through a Cardan shaft. Engine The thermal engine is equipped with a heat exchanger which uses the engine oil as cooling medium. Braking circuit It consists of an independent circuit: the pedal directly acts on the brake pump which dispenses oil to the front axle braking unit with discs in oil bath. The parking brake, of negative type, acts on the braking unit of the service brake. This brake is engaged every time the handler's engine is stopped or pressing down the light pushbutton located to the right of the driving place. Telescopic boom The machine is equipped with a telescopic boom with hydraulic-driven extension. The telescopes slides on interchangeable pads made of wearproof material. Driving cab Type-approved driving cab in compliance with standards ANSI/ASME B56.6-2002. ■ A-4.3 Steering axles/(front and rear) differential gears The differential axles transmit the motion to the wheels. The locking device acting on the front axle enables the machine to move also on low grip grounds. Tyres The machine is equipped with tyres suitably sized for the maximum load allowed on the handler. When worn, they shall be replaced with new ones having the same dimensions and loading capacity. Boom hydraulic circuit It consists of a gear pump connected to the thermal engine which, through a special valve, dispenses oil to the hydraulic drive and a distributor for the following functions: - boom lifting/lowering - telescopic boom extension/retraction - attachment rotation - attachment locking Page OPTIONAL ACCESSORIES The machine can be fitted with a wide range of optional accessories: please address to Terexlift sales network. IMPORTANT Please check the accessories available for your machine. ■ A-4.4 KITS SUPPLIED ON REQUEST The machine is prepared for the installation of the following assembly kits: - Driving cab glasses (including door) - Heater - Air conditioning - Work lights (including courtesy lamp in the cab) - Beacon A-14 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 GENERAL INFORMATION A-5 TECHNICAL DATA AND PERFORMANCE I A D C E B F G ■ A-5.1 MAIN DIMENSIONS A Overall height B Overall width C Track D Cab width E Wheel-base F Length to the front tyres G Length to the attachment holding plate H Ground clearance • Internal steering radius • External steering radius ft ft ft ft ft ft ft ft ft ft ■ A-5.2 RESTRICTIONS OF USE • Angle of approach • Departure angle • Ambient temperature ■ A-5.3 WEIGHT • Weight in working order ■ A-5.4 SPEED Travel speed Max. slope with full load Traction to the dynamometer °C 90° 42° -20°/+40° lb 13245 km/h 0÷32 60% 13007 lb Page A-15 Document 57.0004.9200 - Rev. 0 - 09/2004 TX 66-22 6' - 9" 6' - 7" 5' - 3" 2' - 10" 8' - 8" 13' - 5" 15' - 5" 1' - 4" 7' - 2" 13' - 3" Handler with telescopic boom TX 66-22 GENERAL INFORMATION ■ A-5.5 - PAYLOAD AND REACH TX 66-22 Max lifting height Reach at max height Max reach forward Attachment holding plate rotation Maximum payload Payload at max height Payload at max reach ft ft ft lb lb lb ■ A-5.6 FORKS Dimensions Weight Fork holding frame - class in lb ■ A-5.7 DIESEL ENGINE Make Model/Type Features: - Bore x Stroke Total displacement Power at 2500 rpm (ISO 3046 IFN) ■ A-5.8 ELECTRICAL SYSTEM Voltage Battery ■ A-5.9 MACHINE SOUND LEVELS Guaranteed sound power level (in accordance with the Directive 2000/14/CE) Measured sound pressure level (in accordance with the Directive 98/37/CE) ■ A-5.10 VIBRATION LEVELS Mean assessed vibration level transmitted to arms Mean assessed vibration level transmitted to body Values calculated in accordance with standard prEN13059 22' - 6" 2' - 8" 12' - 6" 135° 6600 5500 2700 Floating type 5.1"x1.8"x47.2" 165+165 FEM II A in cu in kW Turbo version DEUTZ AG BF4M 2011 Diesel 4 cylinders in line 4 strokes direct injection 3.7" x 4.41" 189.65 60 V Ah 12 100 dB Lwa = dB Lpa = m/s2 m/s2 < 2.5 < 0.5 IMPORTANT This is a device of Class A. In a residential environment, such device can cause radio disturbance. In such cases, the operator is required to take suitable measures. Page A-16 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 GENERAL INFORMATION A-7 ITEMS SUPPLIED A-6 LIFETIME The lifetime of the machine is 10 000 hours provided all checks, service jobs and overhauls are done at the times scheduled. Following items are supplied together with the machine: Description TX 66-22 - Socket wrench 24 - Lifting jack 10 ton DANGER ✘ ✘ After this time, the machine must compulsorily be inspected and tested by the Manufacturer before being used again. ■ A-7.1 LITERATURE SUPPLIED The machines comes with the following literature: - Page Warranty and handing over certificate Machine operator's handbook Spare parts catalogue DEUTZ engine use and maintenance manual A-17 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 GENERAL INFORMATION Intentionally blank page Page A-18 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 SAFETY Section B SAFETY TABLE OF CONTENTS B-1 GENERAL REMARKS ................................................................................................. B-2 B-2 PREREQUISITES OF THE PERSONNEL IN CHARGE ............................................... B-2 B-2.1 Requisites of the machine operators ......................................................................... B-2 B-2.2 Requisites of the servicemen ..................................................................................... B-3 B-2.3 Working clothes .......................................................................................................... B-3 B-2.4 Personal protective equipment .................................................................................. B-3 B-3 SAFETY PRECAUTIONS ............................................................................................ B-4 B-3.1 Job site ....................................................................................................................... B-4 B-3.2 Getting ready to work ................................................................................................. B-5 B-3.3 During work or maintenance ...................................................................................... B-5 B-4 SAFETY DEVICES ...................................................................................................... B-7 Page B-1 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 SAFETY B-1 GENERAL REMARKS B-2 Most accidents occurring while working, repairing or maintaining operation machines, are caused by not complying with the basic safety precautions. Therefore, it is necessary to pay steady attention to the potential hazards and the effects that may come of operations carried out on the machine. IMPORTANT If you recognise hazardous situations, you can prevent accidents! For instance, this handbook makes use of special safety symbols to stress any potentially hazardous situation. CAUTION The instructions given in this handbook are the ones established by TEREXLIFT. They do not exclude other safe and most convenient ways for the machine installation, operation and maintenance that take into account the available spaces and means. If you decide to follow instructions other than those given in this manual, you shall absolutely: • be sure that the operations you are going to carry out are not explicitly forbidden; • be sure that the methods are safe, say, in compliance with the rules and provisions given in this section; • be sure that the methods cannot damage the machine directly or indirectly or make it unsafe; • contact TEREXLIFT Assistance Service for any suggestion and the necessary written permission. ■ B-2.1 REQUISITES OF THE MACHINE OPERATORS The operators who use the machine regularly or occasionally (i.e. for transport reasons) shall have the following prerequisites: health: before and during any operation, operators shall never take alcoholic beverages, medicines or other substances that may alter their psycho-physical conditions and, consequently, their working abilities. physical: good eyesight, acute hearing, good co-ordination and ability to carry out all required operations in a safe way, according to the instructions of this manual. mental: ability to understand and apply the enforced rules, regulations and safety precautions. They shall be careful and sensible for their own as well as for the others’ safety and shall desire to carry out the work correctly and in a responsible way. emotional: they shall keep calm and always be able to evaluate their own physical and mental conditions. training: they shall read and familiarise with this handbook, its enclosed graphs and diagrams, the identification and hazard warning plates. They shall be skilled and trained about the machine use. IMPORTANT The operator shall have a licence (or a driving licence) when provided for by the laws enforced in the country where the machine works. Please, ask the competent bodies. In Italy the operator must be at least 18 year old. IMPORTANT If in doubt, it is always better to ask! For this purpose, contact TEREXLIFT: the assistance service is at your disposal. Addresses, phone and fax numbers are given in the cover and in the title-page of this manual. Page REQUISITES OF THE PERSONNEL IN CHARGE B-2 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 SAFETY ■ B-2.2 REQUISITES OF THE SERVICEMEN The personnel charged with the machine maintenance shall be qualified, specialised in the maintenance of earth-moving machines, and shall have the following prerequisites: physical: good eyesight, acute hearing, good co-ordination and ability to carry out all required maintenance operations in a safe way, according to this manual. mental: ability to understand and apply the enforced rules, regulations and safety precautions. They shall be careful and sensible for their own as well as for the others’ safety and shall desire to carry out the work correctly and in a responsible way training: they shall read and familiarise with this handbook, its enclosed graphs and diagrams, the identification and warning plates. They shall be skilled and trained about the machine functioning. ■ B-2.4 PERSONAL PROTECTIVE EQUIPMENT Under special working conditions, the following personal protective equipment should be used: • Breathing set (or dust mask). • Ear-protectors or equivalent equipment. • Goggles or facial masks. IMPORTANT Use only type-approved protective equipment in good condition. IMPORTANT From a technical point of view, the ordinary maintenance of the machine is not a complex intervention and can be carried out by the machine operator, too, provided he has a basic knowledge of mechanics. ■ B-2.3 WORKING CLOTHES During work, but especially when maintaining or repairing the machine, operators must wear suitable protective clothing: • Overalls or any other comfortable garments. Operators should wear neither clothes with large sleeves nor objects that can get stuck in moving parts of the machine. • Protective helmet. • Protective gloves. • Working shoes. IMPORTANT Use only type-approved working clothing in good condition. Page B-3 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 SAFETY • • B-3 SAFETY PRECAUTIONS ■ B-3.1 JOB SITE Always take into account the features of the job site where you are going to work: • Always examine the working area and compare it with the machine dimensions in the different configurations. • Look for the best route to the job site. When the machine is running, nobody can enter its working range. While working, keep the working area in order. Never leave objects scattered: they could hinder the machine movements and represent a danger for personnel. DANGER ELECTRICAL DANGER Do not at any time use the machine during a storm. Pay the greatest attention to overhead electric lines. Always keep at a minimum safe distance from the telescopic boom and the lifted load. Electrical hazards! DANGER DEATH OR INJURY CAN RESULT FROM CONTACTING ELECTRIC POWER LINES. ALWAYS CONTACT THE ELECTRIC POWER LINES OWNER. THE ELECTRIC POWER SHALL BE DISCONNECTED OR THE POWER LINES MOVED OR INSULATED BEFORE MACHINE OPERATIONS BEGIN POWER LINE VOLTAGE REQUIRED CLEARANCE 0 50 200 350 500 750 to to to to to to 50 200 350 500 750 1000 kV kV kV kV kV kV 10 15 20 25 35 45 ft ft ft ft ft ft 3.00 4.60 6.10 7.62 10.67 13.72 m m m m m m CAUTION Make sure the machine (wheels and stabilisers) rests on a firm ground to prevent hazardous unstable conditions. If the ground is not firm enough, position some supporting planks under the stabilisers or the wheels. These plates must grant a specific pressure of 1.2 to 1.5 kg/cm 2 (500x500mm plates are sufficient). Page B-4 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 SAFETY ■ B-3.2 GETTING READY TO WORK Before any operation, following precautions should be taken: • First of all, make sure that the maintenance interventions have been carried out with care according to the established schedule (see section D - Maintenance). • • When entering/leaving the cab or other raised parts, always face the machine; never turn the back. When carrying out operations at hazardous heights (over 1.5 meters from the ground), always use type-approved safety belts or fall preventing devices. CAUTION Set the machine to working configuration and sway it. Use the special inclinometer to the right of the driving place to check that the machine is level before operating it. • • • • • Ensure you have enough fuel to avoid a sudden stop of the engine, especially during a crucial manoeuvre. Clean instruments, data plates, lights and the cab windscreen thoroughly. Check the correct functioning of all the safety devices installed on the machine and in the job site. In case of troubles or difficulties, inform the foreman at once. Never start working under unsafe conditions. Do not carry out any repair work in a makeshift way to start working! • • • • Do not enter/leave the machine while it is running. Do not leave the driving place when the machine is running. Neither stop nor carry out interventions under or between the machine wheels when engine is running. When maintenance in this area is required, stop the engine. Do not carry out maintenance or repair works without a sufficient lighting. ■ B-3.3 DURING WORK OR MAINTENANCE During work, and especially maintenance, always pay the greatest attention: • Do not walk or stop under raised loads or machine parts supported by hydraulic cylinders or ropes only. • Keep the machine handholds and access steps always clean from oil, grease or dirt to prevent falls or slips. • • • • • Page When using the machine lights, the beam should be oriented in order not to blind the personnel at work. Before applying voltage to electric cables or components, check their connection and proper functioning. Do not carry out interventions on electric components with voltage over 48V. Do not connect wet plugs or sockets. Plates and hazard warning stickers shall never be removed, hidden or become unreadable. B-5 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 SAFETY • • • • • • Except for maintenance purposes, do not remove safety devices, shields, protection cases, etc. Should their removal be necessary, stop the engine, remove them with the greatest care and always remember to refit them before starting the engine and using the machine again. Before any maintenance or repair work, stop the engine and disconnect the batteries. Do not lubricate, clean or adjust moving parts. Do not carry out operations manually when specific tools are provided for this purpose. Absolutely avoid to use tools in bad conditions or in an improper way i.e. pliers instead of adjustable wrenches, etc. Before carrying out operations on hydraulic lines under pressure or disconnecting hydraulic components, ensure the relevant line has been previously depressurised and does not contain any hot fluid. Page DANGER Any intervention on the hydraulic circuit must be carried out by authorised personnel. The hydraulic circuit of this machine is fitted with pressure accumulators. You and others could be seriously injured if accumulators are not completely depressurised. For this purpose, shut the engine down and step on the brake pedal 8÷10 times. • Neither smoke nor use open flames in areas subject to fire dangers and in presence of fuel, oil or batteries. B-6 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 SAFETY • • • Do not leave fuel cans or bottles in unsuitable places. Do not empty catalytic mufflers or other vessels containing burning materials without taking the necessary precautions. Carefully handle all flammable or dangerous substances. B-4 SAFETY DEVICES DANGER Several safety devices have been fitted to the machine. They must never be tampered with or removed (see chap. A-3.5). Regularly check the efficiency of such devices (see check card, chap. G-5). In case of faults, stop working immediately and proceed in replacing the defective device. For the checking procedures, read chap. D-3.15. • • • • • • • • Do not tamper with fire-extinguishers or pressure accumulators: explosion hazard! After any maintenance or repair work, make sure that no tool, cloth or other object has been left within machine compartments, fitted with moving parts, or where suction and cooling air circulates. When working, do not give instructions or signs to several people at the same time. Instructions and signs must be given by one person only. Always pay the due attention to the instructions given by the foreman. Never distract the operator during working phases or crucial manoeuvres. Do not call an operator suddenly, if unnecessary. Do not frighten an operator or throw objects by no means. After work, never leave the machine under potentially dangerous conditions. Page B-7 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 SAFETY Intentionally blank page Page B-8 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS Section C OPERATING INSTRUCTIONS TABLE OF CONTENTS C-1 C-2 C-2.1 C-2.1.1 C-2.2 C-2.3 C-2.4 C-2.5 C-2.6 C-3 C-3.1 C-3.2 C-3.2.1 C-3.2.2 C-3.2.3 C-3.2.4 C-3.2.5 C-3.2.6 C-3.2.7 C-3.2.8 C-3.2.9 C-3.3 C-3.3.1 C-3.3.2 C-3.4 C-3.4.1 C-3.4.2 C-3.4.3 BEFORE ENTERING THE MACHINE .... C-2 ENTERING THE MACHINE ................... C-3 Entering the cab (only with glass kit installed) ................................................ C-3 Emergency exit-way (only with glass kit installed) ........................................... C-4 Adjusting the seat ................................. C-5 Fastening the seat belts ....................... C-5 Adjusting the steering column .............. C-6 Adjusting the rear view mirrors ............. C-6 Switching on the cab interior lamp ....... C-6 DRIVING PLACE ................................... C-7 Controls and instruments ..................... C-8 Engine controls and instruments .......... C-9 Ignition switch ....................................... C-9 Forward/reverse gear switch ................ C-9 Brakes ................................................. C-10 Accelerator control ............................. C-10 Pushbutton enabling the attachment coupling/release ................................. C-11 Steering mode selection ..................... C-11 Continuous flow selector .................... C-11 Speed controls ................................... C-11 Auxiliary drive controls ....................... C-12 Instruments and light indicators ......... C-13 Instruments ......................................... C-13 Light indicators ................................... C-13 Control lever ....................................... C-14 Function selection .............................. C-15 Lifting/lowering the boom ................... C-16 Pitching the attachment holding frame forward/back ............................ C-17 Page C-3.4.4 C-3.4.5 C-4 C-4.1 C-4.1.1 C-4.2 C-4.3 C-4.4 C-4.5 C-4.6 C-4.7 C-5 C-5.1 C-5.2 C-5.2.1 C-5.2.2 C-5.3 C-6 C-6.1 C-6.1.1 C-6.2 C-6.3 C-6.4 C-6.5 C-6.5.1 C-6.5.2 C-6.6 C-6.6.1 C-6.6.2 C-6.7 C-6.7.1 Extending/retracting the boom ........... C-18 Quick-coupling the attachments ........ C-19 SETUP ................................................ C-20 Before starting the engine .................. C-20 Checks at the machine start-up ......... C-20 Starting the engine ............................. C-20 Jump-starting the engine .................... C-21 Low temperature starting ................... C-22 Disconnecting the battery ................... C-22 Starting the machine ........................... C-22 Stopping and parking the machine .... C-23 USING THE HANDLER ....................... C-23 Using the load charts .......................... C-24 Handling loads .................................... C-25 Adjusting the forks .............................. C-25 Working phases .................................. C-26 Changing the attachment ................... C-27 TRANSPORTING THE MACHINE ....... C-28 Moving a disabled machine ................ C-28 Unlocking the negative brake ............. C-28 Road or site transfer ........................... C-29 Lifting the machine ............................. C-29 Transporting the machine on other vehicles ............................................... C-30 Parking and storage ........................... C-31 Short inactivity .................................... C-31 Machine storage ................................. C-31 Cleaning and washing the machine .... C-32 Cleaning instructions .......................... C-32 Washing instructions .......................... C-32 Machine disposal ................................ C-32 Disposal of batteries ........................... C-32 C-1 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS C-1 INTRODUCTION This section provides the operator a practical guide for the gradual learning of the machine use. The operator should get into the driving cab and carry out the preliminary adjustments, then memorise the position of the different controls and instruments. The familiarisation with the controls ensures not only a correct use during the working phases, but also a prompt and timely intervention of the operator, when he shall carry out sudden manoeuvres to safeguard his safety and the machine integrity. It is necessary to learn how to use and foresee the machine reactions. Learn how to operate the machine controls in a safe and open place, without obstacles and anybody standing around. Do not ram the controls. Operate them slowly to understand their effect on the machine. Page BEFORE ENTERING THE MACHINE Checks and cleaning • Clean glasses, lights and rear view mirrors. • Check that pins, joints and bolts are well tightened in position. • Check for oil, fuel or coolant leaks. Checking the tyres • Check the correct inflation of the tyres; see par. “Tyre inflation” in the Maintenance section. • Make sure that the tyre plies are not cut or worn. DANGER A tyre burst may result in serious injury; never use the machine if tyres are worn, wrongly inflated or damaged. C-2 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS C-2 ENTERING THE MACHINE ■ C-2.1 CAUTION ENTERING THE CAB (ONLY WITH GLASS KIT INSTALLED) The upper section of the door must be secured to the rear part of the driving cab or latched to the lower section of the same door. CAUTION Always make sure that your hands and shoe soles are clean and dry before getting into the driving cab. Always face the machine when entering and leaving it and hold to the suitable handles. The handler cab is equipped with an access door on the left-hand side. Door opening from outside: • Insert the key and release lock 1. • Press the pushbutton and open the door. � � � Door closing from inside: • Pull the door with force: it locks automatically. Door opening from inside: • Lift lever 2 and release the lock to open the door completely. • Rotate handle 3 to open the upper section of the door and lock it against the special catch. To unlock the door latched in open position: • Press button 4 to unlock the door from the catch, close and latch the door to the lower section using handle 3. Page � C-3 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-2.1.1 Leaving the cab in an emergency (ONLY WITH GLASS KIT INSTALLED) In an emergency, the operator can use he front or the rear window as safety exit-ways. The rear window has handles for partially opening the glass. Such handles are locked in position by some wing nuts 5 which, if driven out, allow opening the glass completely. The front window has two handles 6 which, if turned, enable the operator to pass through. � � Page C-4 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-2.2 ADJUSTING THE SEAT A correct adjustment of the seat ensures the operator a safe and comfortable driving. The handler seat is fitted with devices which allow for the adjustment of the springing, the height and the distance from the controls. • • • � � � Seat distance from the controls The seat is equipped with an adjusting device to slide the same seat forward or back with respect to the steering column. To adjust the seat, pull lever 1 outwards and push the seat to the desired direction. Then release the lever and make sure that the seat locks in position. Springing adjustment Rotate lever 2 clockwise or anticlockwise according to the springing degree required. Rotate clockwise/ anticlockwise to increase/reduce the seat springing. To reverse this control, pull out and rotate the lever knob by 180°. Height adjustment Turn knob 3 clockwise to lift the seat; turn it counter-clockwise to lower the seat. � In some seats height can be adjusted to three different positions. Lift the seat until you hear the click signalling that the seat is locked in position. To lower the seat, raise to end of stroke to release the mechanism, then release the seat: it will return to the bottom position. ■ C-2.3 FASTENING THE SEAT BELTS Sit correctly in the driving seat; then: • The safety belts are equipped with reel retractor. To fasten the belt, pull tab 1 and push it into buckle 2. • To release the belt, push button 3 and remove the tab from the buckle. • Make sure that the buckle is correctly located at the hip point and not on the stomach. • Operate the end adjusters to reach the length you wish and make sure the buckle is always in the middle. � � Page C-5 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-2.4 ADJUSTING THE STEERING COLUMN Both steering column and dashboard can be set to a different angle. For this purpose: • Loosen lever 1 and adjust as required, then retighten lever 1. DANGER Before driving the machine, ensure the steering wheel is perfectly clamped. ■ C-2.5 ADJUSTING THE REAR VIEW MIRRORS The machine is fitted with two rear view mirrors: • The right rear view mirror is located on a special supporting bracket in advanced position and allows checking the area behind the machine, on the righthand side. To adjust its position, manually rotate the joint it is fitted with. • The left rear view mirror is placed on the left upper post of the windscreen and allows checking the area behind the machine, on the left- hand side. To adjust its position, manually rotate the joint it is fitted with. � � � ■ C-2.6 SWITCHING ON THE CAB LIGHTS The ceiling light fixture of the cab has an internal lamp and a courtesy lamp. To switch on the cab interior lights: • Switch 4 in pos. A cab interior lights OFF • Switch 4 in pos. B cab interior lights ON. • Switch 4 in pos. C courtesy lamp ON Page C-6 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS C-3 DRIVING PLACE 1 2 3 2 0 2 4 6 8 10 8 6 4 10 4 5 6 7 80 40 80 40 120 °C 8 120 °C 01234567 9 F N 10 R 18 11 12 13 14 15 16 17 19 23 20 21 22 24 Page C-7 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-3.1 CONTROLS AND INSTRUMENTS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Dashboard Water level Warning light - gear put Brake oil tank Ignition switch Warning light - glow plugs preheating Warning light - air filter clogged Fuse compartment Forward/reverse speed selection lever Steering column locking lever Brake pedal Pushbutton enabling the attachment coupling/release Blank spaces - for pushbuttons Steering selection switch Horn pushbutton Mechanical gear selector Gas pedal Fresh air flap Control lever Continuous flow selector Negative brake on/off switch Storage tray Seat Storage pocket Page C-8 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS C-3.2 ■ C-3.2.2 ENGINE CONTROLS AND INSTRUMENTS Forward/reverse gear selector switch Three-position switch with lock in neutral position: ■ C-3.2.1 Ignition switch Three-position switch: No circuit under voltage, key can be removed and engine is stopped N Neutral position; no gear engaged F Shift lever to pos. F to select the forward gear R Shift lever to pos. R to select the reverse gear Circuits under voltage, presetting for the engine starting. Board controls and instruments are on. The warning light 6 signalling the glow plugs preheating comes on. Wait until the light goes off before starting the engine. Engine starting; when released, key springs back to pos. automatically. 80 40 80 120 40 °C °C 01234567 F N R � Page C-9 Document 57.0004.9200 - Rev. 0 - 09/2004 120 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-3.2.3 11 ■ C-3.2.4 Brakes Service brake pedal Gradually step on the brake pedal to decelerate and stop the machine. The pedal operates on the front axle. Fully depressing the brake pedal causes a reset of the displacement of the power drive pump making the brake action more powerful. 21 Accelerator control 17 Gas pedal Its pressure controls the engine rpm and, coupled to the gearbox, the machine speed. It is fitted with an adjustable stop in the lower part Parking brake The parking brake of negative type engages automatically when the engine is stopped. When the handler’s engine is restarted, pressing the pushbutton switch 21 unlocks the parking brake. To stop the handler without shutting down the engine, press the pushbutton switch 21 to engage the parking brake and push it once again to disengage the brake. Every pressure of the pushbutton switches the warning light on and off. When the red warning light is on, the parking brake is engaged. CAUTION Never use the parking brake to slow down the machine, unless in an emergency. It may reduce the brake efficiency. 80 40 80 40 120 °C 120 °C 01234567 F N R 21 11 17 Page C-10 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-3.2.5 Pushbutton enabling the attachment coupling/release 12 Selection button Pushbutton with two stable positions. Pressing this button activates the attachment coupling and release. The built-in button light switches on. ■ C-3.2.6 14 ■ C-3.2.7 20 2 Pressing this selector again lets the circuit returns to normal mode: oil is delivered to the attachment only when the control lever is operated. The built-in light switches off. Steering mode switch Three-position switch for the selection of the steering mode: Crab steering 0 Two-wheel steering 2 Four-wheel steering Selection button Button with two stable positions: 1 Pressing this selector delivers a continuous flow of oil to the attachment in use. The built-in light switches on. Steering mode selection 1 Continuous flow selector ■ C-3.2.8 16 Speed controls Mechanical gearbox pushbutton Used to engage the 1st or 2nd gear. Push the button to select the required speed. Each pressure corresponds to the selection of a new speed. The selection is signalled by warning light 3 which illuminates the glass corresponding to the selected speed. 80 40 80 40 120 °C 120 °C 01234567 3 F N R 16 12 14 20 Page C-11 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-3.2.9 15 Auxiliary drive controls Horn pushbutton Pushbutton with green glass Press this button to operate the horn. 80 40 80 40 120 °C 120 °C 01234567 F N R 15 Page C-12 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS C-3.3 INSTRUMENTS AND LIGHT INDICATORS ■ C-3.3.1 54 Indicator light - parking brake engaged This light comes on to warn that the negative parking brake is engaged. 67 Indicator light accumulator Not activated. 68 Indicator light - turn signals Green indicator light that signals when turn signals are ON. This indicator is active only when the lights kit is installed. 6 Indicator light - glow plugs preheating Green light indicators which signal the preheating phase of the engine glow plugs. Before starting the engine wait for these lights to go off. 7 Indicator light - air filter soiled Orange light indicator which signals when the air intake filter of the engine is getting soiled. Clean or replace the filter cartridge immediately. 6 Instruments Engine coolant temperature indicator Signals the engine coolant temperature. 53 66 Fuel gauge Signals the fuel level within the tank. 01234567 52 51 Hour-meter Signals the total operating hours of the machine. Hydraulic oil temperature indicator Signals the temperature of the hydraulic oil within the reservoir. ■ C-3.3.2 Light indicators 60 Indicator light - high beam Blue indicator light that signals when high beam is ON. This indicator is active only when the lights kit is installed. 61 Indicator light - air filter soiled Not activated. 64 Indicator light - low battery charge Signals a low charge by the alternator. 65 Indicator light - low engine oil pressure It lights when the engine oil pressure is too low. negative brake 80 40 120 °C 7 Indicator light - position lights Green indicator light that signals when position lights are ON. This indicator is active only when the lights kit is installed. 63 - 012 F N R 60 61 62 63 64 65 66 67 68 01234567 Page 51 C-13 Document 57.0004.9200 - Rev. 0 - 09/2004 52 53 54 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS C-3.4 CONTROL LEVER Handlers are equipped with a hydraulically driven servo-controlled lever. The lever has two pushbuttons: one for coupling/ releasing the attachments and the other for pitching the attachment frame forwards/backwards . Shifting the lever to one of the four directions (right/ left, forwards/backwards) moves the boom up and down and the telescope out and in. IMPORTANT Seize the control lever correctly and move it gently. The motion speed of the actuators depends on the lever position: a small motion results in a slow motion of the actuators; vice versa, a full range motion of the lever corresponds to the max. speed of the actuator. CAUTION The control lever shall be operated only when correctly seated in the driving place. CAUTION Before operating the control lever, make sure that nobody is within the working range of the machine. Page C-14 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-3.4.1 Function selection The lever is enabled to carry out the following motions: • Boom lowering/lifting shift the control lever to or • Boom extraction/retraction shift the control lever to or • Attachment back/forward tilting press button and shift the control lever to or • Attachment coupling/release press button together with the dashboard enabling button and shift the lever to or Page C-15 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-3.4.2 Lifting/lowering the boom CAUTION Before operating the boom, make sure that nobody is within the working range of the machine. To lift or lower the boom: • Smoothly shift the lever to position to lift the boom or to position to lower it. Page C-16 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-3.4.3 Pitching the attachment holding frame forwards/backwards CAUTION Before operating the boom, make sure that nobody is within the working range of the machine. To tilt the attachment holding frame forwards/ backwards: • Press button and smoothly shift the lever to position to tilt the frame forwards or to position to tilt it backwards. Page C-17 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-3.4.4 Extending/retracting the telescope CAUTION Before operating the boom, make sure that nobody is within the working range of the machine. To extend or retract the boom telescope: • Smoothly shift the lever to position to extend the boom or to position to retract it. Page C-18 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-3.4.5 Quick-coupling the attachments CAUTION Before operating the boom, make sure that nobody is within the working range of the machine. To lock the attachments: • Press button together with the button 햾 on the dashboard to enable the function. • Shift the lever to position to unlock the attachment or to position to lock the attachment. F N R 12 Page C-19 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-4.2 C-4 SETUP STARTING THE ENGINE For the low temperature starting, see paragraph C-4.4. ■ C-4.1 • BEFORE STARTING THE ENGINE To ensure safe conditions to the operators and the bystanders, and a longer life to your machine, perform a walk-around inspection before starting the engine. • Remove any dirt or rubbish from the cab interior, and especially from pedals and control levers. • Remove oil, grease and mud from pedals and control levers. • Make sure that your hands and shoe soles are clean and dry. • Check the seat belts can be fastened properly. • Check that lights, indicators, side/tail lights, hazard indicator lights, wipers and horn are in working order. • Adjust the driving seat so that you can reach all control levers comfortably and fully depress the brake pedal without moving your back from the driving seat. • Adjust the rear view mirrors to give you a good view close behind the machine when you are correctly seated. • Check the parking brake is engaged. • Put the forward/reverse speed selection lever to neutral. • Step on the gas pedal. • To start the engine, turn the ignition switch to position . Release the switch when the engine starts. If the engine does not start within 20 seconds, release the key and wait at least 2 minutes before attempting again. • After the start-up, let the engine run at idle for some seconds before engaging a gear; this allows for a gradual warm up of the engine oil and a better lubrication. • In case of engine jump-starting, remove the booster cables (see following chapter). ATTENTION If the light indicators do not switch off/on when engine is running, immediately stop the machine and find and rectify the fault. IMPORTANT ■ C-4.1.1 Checks at the machine start-up Check the efficiency of the safety devices as described in chap. D-3.15, namely: • block valves • machine start control. Engine cannot be started if the speed switch is not in the neutral position and the operator is not correctly seated in the driving seat. DANGER After the start-up, when leaving the driving place, the engine continues to run. DO NOT LEAVE THE DRIVING PLACE BEFORE HAVING SHUT THE ENGINE DOWN and LOWERED THE BOOM TO THE GROUND. Page C-20 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-4.3 JUMP-STARTING THE ENGINE DANGER B When jump-starting the engine through the battery of another machine, make sure that the two vehicles cannot collide to prevent formation of sparks. Batteries give off a flammable gas and sparks may burn it and cause an explosion A Do not smoke when checking the electrolyte level. Keep any metal object like buckles, watch straps, etc. clear of the battery positive (+) terminal. These elements can short between the terminal and nearby metal work and the operator can get burned. The booster supply must have the same rated voltage and output of the battery installed on the handler. To jump-start the engine: • Turn any users off by the special control levers. • Put the gear lever to neutral and engage the parking brake. • Ensure the machine battery A is connected to the frame earth, the terminals are well tightened and the electrolyte level is regular. • Connect the two batteries as shown in the figure. Connect first the positive terminals of the two batteries, then the negative terminal of the booster supply B to the machine frame earth. • If the booster supply is installed on a second vehicle, make sure that the latter does not touch the handler; then start the vehicle and reach an rpm corresponding to 1/4 of full throttle. • Turn the ignition key and start the handler, then follow the procedure explained in chapter C-4.2 “Starting the engine”. • Disconnect the cables. Remove first the negative terminal from the frame earth, then from the booster supply. Disconnect the positive terminal from the machine battery, then from the booster supply. Page DANGER Use only a 12V battery; other devices like battery chargers, etc. may cause an explosion of the battery or result in damage to the electrical system. C-21 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-4.4 ■ C-4.5 LOW TEMPERATURE STARTING In case of cold starting, use an oil with a SAE viscosity adequate to the ambient temperature. Please refer to the DEUTZ engine use and maintenance manual. The machine is supplied with oil SAE 15W/40. DISCONNECTING THE BATTERY During maintenance or repair works, and while welding, turn off the battery main switch , located behind the rear right wheel compartment. To start the engine from cold, proceed as follows: • Put the forward/reverse speed selection lever to neutral. • Turn the ignition switch to position and wait until the warning light 6 signalling the glow plugs preheating goes off. Step down on the gas pedal and start the engine turning the ignition switch to . Release as soon as the engine starts. • • Let the engine run at idle for a few seconds before putting a gear; this allows for a gradual warm up of the engine oil and a better lubrication. ■ C-4.6 STARTING THE MACHINE When the engine reaches the running temperature, ensure all parts are in transfer position and the gearbox lever is in neutral. Then, proceed as follows: • • • • Select the required steering mode. Select the required gear (forward or reverse). Release the parking brake pressing button 21 (the warning light on the pushbutton must be off). Slowly step on the gas pedal to start moving off. In case of engine jump-starting, remove the booster ables (see chapter C-4.3). CAUTION Do not operate the forward/reverse gear lever when the machine is running. The machine would reverse the running direction abruptly and you could seriously be injured. Page C-22 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-4.7 STOPPING AND PARKING THE MACHINE When possible, stop the machine on a dry, level and solid ground. Then: • Bring the machine to a smooth stop by easing up the gas pedal and stepping down on the brake pedal. • Set the forward/back speed lever to neutral position. • Engage the parking brake pressing button 18 (the warning light on the pushbutton must be on). • Release the service brake pedal. • Rest the attachment coupled to the boom flat on the ground. • Rotate the ignition key to “0” and remove the key. • Leave the driving cab and lock the cab door. • Set the battery cut-out switch to OFF position. C-5 USING THE HANDLER This chapter describes some techniques and provides instructions for a safe use of the machine fitted with standard forks. Before using different attachments, thoroughly read the chapter “Optional attachments". CAUTION Before using the machine, inspect the job site and check for possible hazardous conditions. Make sure that there are no holes, moving banks or debris that may cause you to lose the control of the machine. ELECTRICAL DANGER Pay the greatest attention when working close to electric lines. Check their position and ensure that no part of the machine operates at less than 6 meters from the power lines. DANGER Always face the machine when getting off the driving cab; make sure that your hands and shoe soles are clean and dry, and hold to the handholds to prevent falls or slips. DANGER CAUTION For a safe use of the machine, always check the weight of the loads going to be handled. Always refer to the load charts applied on the cab windscreen or to the quick guide with the fork capacity ratings. Always engage the parking brake after stopping the machine to prevent possible accidental motions of the vehicle. Page C-23 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-5.1 USING THE LOAD CHARTS The charts indicating the maximum permissible load in relation to the boom extension and the lifting height of the same load are installed on the cab windscreen and/ or illustrated in the quick guide. The load chart indicates the payload limits of the machine under safe conditions. To operate under safe conditions, always refer to these charts. CAUTION The load charts applied on the cab windscreen refer to a stationary machine standing on a solid and level ground. Raise the load some centimetres and check its stability before raising it completely. CAUTION The load charts illustrated in this manual are given only as a mere example. To define the payload limits, refer to the load charts applied in the cab of your machine. 25 TX 66-22 CAPACITY CHART 67 deg E 60 deg D 20 C 50 deg B A 40 deg 30 deg b 66 00 l 550 0 lb 15 4400 lb 10 3300 lb ft 10 deg 3000 lb 5 2700 lb 20 deg 0 deg 0 -3 deg E D C B A Forward reach 3 15 10 0 5 Page C-24 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-5.2 HANDLING LOADS ■ C-5.2.1 Adjusting the forks Forks shall be spaced to suit the load going to be handled. For this purpose: • • • Loosen the nut of the locking screws. Raise the forks and slide them on the pivot until correct spacing. Lock the screws re-tightening the nut. CAUTION • The centre of gravity of the load must always be halfway between the forks. • Ensure you exactly know the weight of the load before handling it. • When extending the boom, do not exceed the payload limit. • Refer to the payload limits given in the load chart applied on the cab windscreen or in the quick user’s guide. • Space the forks as wide as possible to suit the load being handled. Page C-25 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-5.2.2 Working phases When forks are correctly spaced, the handler is ready to use. Work can be subdivided into three different phases: loading, transfer and unloading. • Release the parking brake and start a new working cycle. CAUTION Loading phase • Approach the load to the handled perpendicularly and check that the machine is level on the inclinometer. • Insert the forks under the load and raise the load some centimetres. • Pitch the forks backwards and check the machine stability before handling a load. Do not move off when the load is raised 20÷30 cm above the ground. Risk of machine overturning or load fall. Transfer phase • Do not start or brake abruptly. • Drive to the unloading point cautiously and keep the load 20÷30 cm from the ground. • Suit the machine speed to the ground conditions to avoid dangerous jumps, side skids of the vehicle and possible load falls. • When driving on slopes or ramps, hold the load uphill. DANGER Do not drive on slopes sideways; this wrong manoeuvre is one of the main reasons for accidents due to vehicle overturning. Unloading phase • Drive to the unloading point with straight wheels and bring the machine to a smooth stop leaving enough space to operate the boom. • Put the parking brake and set the transmission to neutral. • Position the load some centimetres above the desired position and set the forks level. • Lower the load and make sure it is level. • Carefully withdraw the forks by operating the boom retraction control and, if necessary, raise or lower the boom as forks come out. • When the forks are clear of the load, set them to transfer position. Page C-26 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-5.3 CHANGING THE ATTACHMENT CAUTION ATTENTION Use only attachments directly manufactured or recommended by Terexlift and detailed in the “Optional attachments” section. After substitution, visually check the attachment is correctly coupled to the boom, before operating the machine. A wrongly coupled attachment may result in damage to persons or things. To change an attachment, operate as follows: • Drive to the place where you will release the mounted attachment (when possible, a solid and sheltered site). • Disconnect the quick connectors of the attachment (if any), and connect the hydraulic locking pipes of the attachments to couplings A. • Rest the attachment flat on the ground. • Pitch the attachment holding frame forward and lower the boom to release the attachment upper lock. • Move back with the machine (or with the boom) and drive to the new attachment to be coupled. • Hold the frame pitched forward and hook the upper lock of the new attachment. • Retract and raise the attachment some centimetres. It will centre automatically on the quick coupling frame. • Operate the control lever to lock the attachment. Page C-27 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS • Couple the connectors of the attachment, if any, to the quick couplings of the frame. C-6 TRANSPORTING THE MACHINE ■ C-6.1 MOVING A DISABLED MACHINE Tow the machine only when no alternative is possible, since this operation may result in serious damage to the transmission. When possible, repair the machine on site. When the machine shall absolutely be towed: DANGER After the substitution of an attachment or after any coupling operation, visually check the attachment. A wrongly coupled attachment may result in damage to persons or things. • • • • • • • Unlock the negative brake (see chap. C-6.1.1) Tow the machine for short distances and at a low speed only. Use a rigid drawbar. Select the two-wheel steer. Set the gearbox lever to neutral. When possible, start the engine and use the hydraulic drive and the braking system. Raise the front wheels of the machine and remove the Cardan shaft of the transmission. ■ C-6.1.1 Unlocking the negative brake To unlock the negative brake of a faulty machine, proceed as follows: • Loosen the two opposite screws located on the front axle in order to remove the washers. • Remove the horseshoe-shaped washers located under the two screws. • Re-tighten screws turning alternately the front screw and the rear screw 1/2 turn to unlock the brake. To relock the nagetive brake, loosen the screws turning alternately the front screw and the rear screw 1/2 turn, refit the horseshoe washers and re-tighten screws . Page C-28 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-6.2 ROAD OR SITE TRANSFER When travelling on public roads, strictly obey the local or national road traffic regulations. Besides, take into account the following general precautions: • Align the rear wheels. • Select the two-wheel steer. • withdraw the floating forks. • • • Retract boom and attachment to transfer position. Make sure the instruments are in efficient working order. Start the machine. • Select the forward or reverse speed. • The transfer speed of the vehicle will depend on the engine rpm. ■ C-6.3 LIFTING THE MACHINE When the machine shall be lifted, use only means having a suitable capacity. The characteristic data are detailed in the relevant chapter of this manual and on the identification plate. For the machine lifting, anchor the chains to the special lugs on the machine (marked with the decal below). CAUTION Public road circulation is allowed only for transferring an unloaded machine. Do not use the machine to tow trailers. Page C-29 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-6.4 TRANSPORTING THE MACHINE ON OTHER VEHICLES To transport the machine on another vehicle, follow the steps below: • Put chocks at the machine wheels. • Ensure ramps are correctly positioned. • Retract the boom to transfer position. • Carefully drive the machine onto the transporting vehicle. • Put the parking brake and rest the attachment flat on the vehicle platform. • Ensure the overall dimensions do not exceed the allowed limits. • Shut the engine down and close the driving cab of the machine. • Secure the machine to the vehicle platform by wheel-chocks. • Anchor the machine to the transporting vehicle with suitable chains. Page C-30 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-6.5 PARKING AND STORAGE ■ C-6.5.1 Short inactivity Always park the machine in a safe way after a working day, a shift and at night. ■ C-6.5.2 Machine storage In case of extended inactivity of the machine, follow the above precautions. Additionally: • Wash the machine thoroughly. For a better cleaning, remove grills and protection casings Take all precautions to prevent damage to those persons who will approach the machine while stationary: • Carefully dry all machine parts by blowing some compressed air. • Park the machine so that it does not hinder other operations. • Lubricate the machine thoroughly. • • Lower the boom fitted with attachment on the ground. Do a walk-around inspection and replace any worn or damaged part. • Re-paint any worn or damaged part. • Remove the key from the ignition switch. • • Disconnect the battery by the appropriate switch (“Battery cut-out switch”). Remove the battery, smear its terminals with vaseline and store it in a dry place. Battery can be used for other purposes. Otherwise, periodically check its charge level. • Refuel the tank to prevent internal oxidation. • Store the machine in a sheltered and wellventilated place. • Start the engine for about 10 minutes at least once a month. IMPORTANT Always remember that the ordinary maintenance must be carried out even during the machine inactivity. Pay particular attention to the fluid levels and to those parts subject to ageing. Before restarting the machine, carry out an extraordinary maintenance and carefully check all mechanical, hydraulic and electrical components. Page C-31 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPERATING INSTRUCTIONS ■ C-6.6 CLEANING AND WASHING THE ■ C-6.7 MACHINE DISPOSAL MACHINE ■ C-6.6.1 Cleaning instructions Clean the machine in accordance with the following instructions: • Remove any oil or grease traces with a dry solvent or a volatile mineral alcohol • Before assembling a new part, remove any protection product (rust-preventer, grease, wax etc.). • Remove any trace of rust from metal parts with some emery cloth before smearing the part with a protection product (rust-preventer, paint, oil etc.). PROTECT THE ENVIRONMENT At the end of the machine life, call in a specialised firm to dispose of it in compliance with the local or national regulations. ■ C-6.7.1 Battery disposal PROTECT THE ENVIRONMENT ■ C-6.6.2 Washing instructions External washing Before washing the machine, check that the engine is shut down and the doors and windows are closed. Do not, at any times, use fuel to clean the machine. Use water or some steam. In cold climates, dry the locks after washing or smear them with an antifreeze. Before using the machine again, check its conditions. Internal washing Wash the machine interior with some water and a sponge. Do not use water at high pressure. After washing, dry with a clean cloth. Washing the engine Before washing the engine, protect the air intake filter to prevent water from entering the circuit. Page Used lead-acid batteries cannot be disposed of as normal industrial solid wastes. Because of the presence of harmful substances, they must be collected, eliminated and/or recycled in accordance with the laws of the UE. In Italy, used or discarded batteries have been classified as “Toxic wastes” in accordance with Presidential decree n. 397 of 09/09/1988 and Law n. 475 O.G. n. 18 of 09/11/1988 because they contain lead and sulphuric acid. Their disposal through recycling must be done only through companies authorised and belonging to the “Consorzio Obbligatorio Batterie Esauste e dei rifiuti piombosi” (Cobat) which collect and dispose of used lead-acid batteries throughout the national territory. Used batteries must be kept in a dry and confined place. Make sure the battery is dry and the cell plugs are tight. Place a sign on the battery to warn of not using it. If before disposal the battery is left in the open air, it will be necessary to dry, smear the box and the elements with a coat of grease and tighten the plugs. Do not rest the battery on the ground; it is always advisable to rest it on a pallet and cover it. The disposal of batteries shall be as rapid as possible. C-32 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 MAINTENANCE Section D MAINTENANCE TABLE OF CONTENTS D-1 D-2 D-2.1 D-3 D-3.1 D-3.2 D-3.3 D-3.4 D-3.5 D-3.5.1 D-3.6 D-3.7 D-3.8 D-3.9 D-3.10 D-3.10.1 D-3.10.2 D-3.11 D-3.11.1 D-3.11.2 D-3.12 D-3.13 D-3.14 D-3.15 D-4 D-4.1 D-4.2 D-4.3 D-5 D-5.1 D-5.2 D-5.2.1 D-5.2.2 D-5.2.3 D-5.2.4 LUBRICANTS - HEALTH AND SAFETY PRECAUTIONS .............................. D-2 ROUTINE MAINTENANCE ............................................................................ D-3 Oil change schedule ...................................................................................... D-4 MAINTENANCE JOBS .................................................................................. D-5 Disconnecting the battery ............................................................................. D-5 Access to the engine and tanks compartments ........................................... D-6 Greasing ........................................................................................................ D-7 Tyres and wheels .......................................................................................... D-8 Brakes ........................................................................................................... D-9 Checking the brake oil level .......................................................................... D-9 Engine air filter ............................................................................................. D-10 Cab air filter ................................................................................................. D-11 Engine cooling circuit .................................................................................. D-11 Checking the oil level in the tank ................................................................ D-12 Changing the oil filter canisters on the intake line ...................................... D-13 Transmission oil filter .................................................................................. D-13 Auxiliary circuits oil filter .............................................................................. D-14 Oil level in the differential gears and the rducer .......................................... D-15 Front and rear differential gears .................................................................. D-15 Reducer ....................................................................................................... D-15 Oil level in the (front/rear) wheel reduction gears ........................................ D-16 Shafting alignment ...................................................................................... D-17 Adjusting the sliding pads of the boom sections ........................................ D-18 Checking the safety devices ....................................................................... D-19 ELECTRICAL SYSTEM ................................................................................ D-21 Battery ......................................................................................................... D-21 Fuses and relays ......................................................................................... D-22 12V DC lamps (only with glass kit installed) ................................................ D-24 REFUELLING ............................................................................................... D-25 Refuelling ..................................................................................................... D-25 Product specifications ................................................................................ D-25 Engine oil ..................................................................................................... D-25 Lubrication oils and relevant filtering elements ........................................... D-25 Fuel .............................................................................................................. D-26 Grease ......................................................................................................... D-26 Page D-1 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 MAINTENANCE D-1 INTRODUCTION A thorough and regular maintenance keeps the machine in a safe and efficient working condition. For this reason, it is advisable to wash, grease and service the machine properly, especially after having worked under particular conditions (muddy or dusty environments, heavy operations, etc.). LUBRICANTS - HEALTH AND SAFETY PRECAUTIONS Health A prolonged skin contact with oil can cause irritation. Use rubber gloves and protective goggles. After handling oil, carefully wash your hands with soap and water. Always ensure all machine components are in good condition. Check for oil leaks or loosening of guards, and make sure that the safety devices are efficient. In case of defects, find and rectify them before using the machine again. Storage Always keep lubricants in a closed place, out of the children’s reach. Never store lubricants on the open air and without a label indicating their contents. The maintenance interventions are based on the machine working hours. Regularly check the hourmeter and keep it in good condition to define the maintenance intervals correctly. Disposal New or exhausted oil is always polluting! Never drain oil on the ground. Store new oil in a suitable warehouse. Pour exhausted oil into cans and deliver them to specialised firms for disposal. Not respecting the ordinary maintenance schedule of this manual automatically voids TEREXLIFT warranty. IMPORTANT For the engine maintenance, please refer to the specific Operator handbook supplied with the machine. Oil leaks In case of accidental oil leaks, cover with sand or typeapproved granulate. Then scrape off and dispose of it as chemical waste. First aid Eyes Intake Skin : In case of accidental contact with the eyes, wash with fresh water. If the irritation persists, seek medical advice. : In case of oil intake, do not induce vomiting, but seek medical advice. : In case of a prolonged contact, wash with soap and water Fire In case of fire, use carbon dioxide, dry chemical or foam extinguishers. Do not use water. Page D-2 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 MAINTENANCE Every 50 working hours or weekly D-2 ROUTINE MAINTENANCE Jobs to be done in addition to those above A wrong or neglected maintenance can result in possible risks for both operator and bystanders. Make sure maintenance and lubrication are carried out according to the manufacturer’s instructions to keep the machine safe and efficient. The maintenance interventions are based on the machine working hours. Regularly check the hourmeter and keep it in good conditions to define the maintenance intervals correctly. Make sure any defect detected during the maintenance is promptly rectified before using the machine. 1 2 3 4 Every 250 working hours or monthly Jobs to be done in addition to those above 1 2 3 ATTENTION 4 All " ▲ " marked operations must be carried out by a skilled technician. 5 6 During the first 10 working hours 1 2 3 4 Check the oil level of reduction gears, gearbox and differential gears Regularly check the tightening of the wheel bolts Check the tightening of all bolts and nuts Check the couplings for oil leaks Within the first 50 working hours 1 7 8 9 10 Change the oil for the first time 11 Every 10 working hours or daily 1 2 3 4 5 6 7 Check the engine oil level Clean the air suction filter Clean the radiator, if necessary Check the hydraulic oil level in the tank Check the greasing of the boom section pads Grease the attachment holding frame Grease all joints of the boom, the rear axle shaft joint, the transmission shafts, the front and rear axles and any equipment of the machine 8 Check the efficiency of the lighting electric system 9 Check the efficiency of braking system and parking brake 10 Check the efficiency of the steering selection system 11 Check the efficiency of the fork balancing system. 12 Make sure the safety devices installed are in efficient working order - see procedure in chap. D-3.15. Page Check the tension of the alternator belt Check the tyre inflation Check the tightening of the wheel nuts Check the tightening of the Cardan shaft screws 12 13 Change the engine oil and relevant filter Check the oil level of the front and rear differential gears and the gearbox Check the oil level in the four wheel reduction gears Check the condition of the canister of the engine air filter; renew the canister if necessary Check the clamping of the cableheads to the battery terminals Check the air suction hose between engine and filter Check the cylinder chromium-plated rods Check the hydraulic lines are not worn because of rubbing against the frame or other mechanical components Check the electric cables do not rub against the frame or other mechanical components ▲ Check the wear of the sliding pads of the boom sections ▲ Adjust the play of the sliding pads of the boom sections Remove any grease from the boom, then regrease the sliding parts of the boom sections Check the level of the battery electrolyte Every 3 working months 1 Check the efficiency of the block valves - see chap. D-3.15. D-3 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 MAINTENANCE Every 500 working hours or every six months Jobs to be done in addition to those above. 1 2 3 4 5 6 7 8 9 Visually check the smoke quantity evacuated from the engine exhaust Check the tightening of the engine fixing screws Check the tightening of the cab fixing screws Check the backlash between pins and bushings in all joints Change the hydraulic oil filter of the transmission Change the hydraulic oil filter in the tank Have the hydraulic system checked by a skilled technician Change the main cartridge of the engine air filter Clean or replace, if nececessary, the air filter in the cab Every 1000 working hours or yearly Jobs to be done in addition to those above 1 2 3 4 Change the oil in the front and rear differential units and in the power divider Change the oil in the four wheel reduction gears Change the hydraulic oil Change the safety cartridge of the engine air filter ■ D-2.1 OIL CHANGE SCHEDULE Job Engine Axles and power divider Hydraulic oil operating hours* service interval* Oil level check 10 daily First change 50 - Subsequent changes 250 monthly Oil level check 250 monthly - - Subsequent changes 1000 yearly Oil level check 250 monthly Subsequent changes 1000 yearly First change Oil type SHELL RIMULA 15W-40 FUCHS TITAN GEAR LS 85 W-90 API GL-5 LS / GL-5 SHELL TELLUS T 46 DENISON HF-1, DIN 51524 part 3 Cat. HV * whichever occurs first Page D-4 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 MAINTENANCE D-3 MAINTENANCE JOBS ATTENTION DANGER All maintenance interventions must be carried out with engine stopped, parking brake engaged, working attachments flat on the ground and gear lever in neutral. High pressure lines must be replaced by qualified personnel only. Any foreign matters entering the closed circuit may result in a sudden deterioration of the transmission. ATTENTION CAUTION When raising a component for maintenance purposes, secure it in a safe way before any maintenance intervention. CAUTION Any intervention on the hydraulic circuit must be carried out by skilled personnel. The hydraulic circuit of this machine is fitted with pressure accumulators. You and others could be seriously injured if accumulators are not completely depressurised. To depressurise the accumators, just steer the machine wheels some times with engine shut down until noticing a gradual binding of the handwheel. The qualified staff charged with the maintenance of the hydraulic circuit must clean all areas around with care before any intervention. PROTECT THE ENVIRONMENT The handling and disposing of used oils can be ruled by local or national regulations. Address to authorised centres. CAUTION Before any operation on hydraulic lines or components, make sure there is no residual pressure. For this purpose, stop the engine, engage the parking brake and operate the control levers of the distributors in both working directions (alternately) to depressurise the hydraulic circuit. Page ■ D-3.1 DISCONNECTING THE BATTERY During maintenance or repair works, and while welding, turn off the battery main switch, located behind the rear right wheel compartment (C-4.5, p. C-22). D-5 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 MAINTENANCE ■ D-3.2 ■ ACCESS TO THE ENGINE AND TANKS COMPARTMENTS Engine compartment For any operation within the engine compartment, open the protection bonnet. Hood is equipped with lock & key and a supporting rod that holds it in position. From the engine compartment, you get access to: • Thermal engine • Engine air filter • Hydraulic oil tank plug • Radiator fluid compensation cup • Battery To get access to the engine compartment: • • • • Shut the engine down and put the parking brake. Unlock the bonnet lock Lift the bonnet using the special handle until it latches in the gas spring. To close the bonnet: press on the green locking device on the gas spring and lower the bonnet. DANGER Take all precautions when approaching the engine compartment. Some parts of the engine may be very hot. Always use protective gloves. ■ Diesel fuel tank compartment To gain access to the fuel tank, open the rear cover of the machine as follows: • Shut the engine down and put the parking brake. • Fully raise the cover by means of the special handle. Page D-6 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 MAINTENANCE ■ D-3.3 GREASING ATTENTION Before injecting grease into the greasers, thoroughly clean them to avoid that mud, dust or other matters can mix with the lubricant and reduce or annihilate the lubrication effect. Remove any old grease with a degreaser from the telescopes before smearing them with new grease. Regularly grease the machine to grant it efficient conditions and a long life. By means of a pump, inject grease into the special greasers. As the fresh grease comes out, stop the operation. The greasing points are shown in the following figures: - the symbol represents the points to be greased by a pump - the symbol represents the points to be greased by a brush. SERVICE INTERVAL Running-in ____________________________ None Ordinary ____________________ Every 10 hours Page D-7 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 MAINTENANCE ■ D-3.4 TYRES AND WHEELS DANGER Over-inflated or overheated tyres can burst. Do not flame-cut or weld the wheel rims. For any repair work, call in a qualified technician. YES NO WRONG WAY RIGHT WAY For the tyre inflation or substitution, please refer to the table below: TX 66-22 Standard Optional Dimensions 405/70 R24 P.R. (or load index) 14 pr Wheel disc Pressure 400/70 R20 8 holes DIN 70361 bar Psi 4.0 58 On new machines, and when a wheel has been disassembled or replaced, check the nut torque of the wheels every 2 hours until they stay correct. ATTENTION Always use tyres having the dimensions indicated in the vehicle registration card. SERVICE INTERVAL Running-in _________ Within the first 10 hours Ordinary __________________ Every 250 hours Page D-8 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 MAINTENANCE D-3.5 BRAKES • For any intervention on the braking system (adjustment and/or substitution of the brake discs) call in a specialised technician. The malfunctioning of the braking system may depend on the presence of air within the hydraulic circuit. The braking system has two bleeding valves: valve for the service brake circuit and valve for the negative parking brake circuit. To bleed the circuit of the service brake: • Make sure that the oil is level within the feeding tank . • Step on the brake pedal repeatedly. • Slowly unscrew valve and re-close it as soon as oil mixed with air bubbles comes out. • Repeat the operation until bubble-free oil comes out. • Bleed from both sides of the machine. To bleed the circuit of the negative parking brake: • Press the parking brake button . As soon as the light indicator on the button goes off, start bleeding through valve until air-free oil comes out. D-3.5.1 Checking the brake oil level The oil within the braking circuit must be at about 2 cm from the tank plug . Level Page D-9 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 MAINTENANCE ■ D-3.6 ENGINE AIR FILTER Clean the engine air filter every 10 hours; replace the filtering element, if necessary. 1 Cleaning and changing the external element: - Stop the engine and engage the parking brake. - Unscrew wingnut A and remove cover B. - Unscrew wingnut C and remove the outer element D. - Clean the filter bowl. - Dry clean the cartridge (max. pressure: 6 bar) and direct the air jet from inside to outside. - Check for cracks in the filtering element by introducing a lamp inside. - Smear the seal with grease, then refit the element. - Tighten wingnut C, close cover B and tighten with wingnut A. ATTENTION As soon as the warning lamp 7 on the cab dashboard switches on, replace the outer element. 2 Changing the internal element: - See step 1 for removing the outer element. - Loosen wing nut E and remove the inner element F. - Clean the filter bowl. - Smear the seal with grease, then mount the new element and make sure it is correctly positioned. - Refit the outer element and the cover (see step 1). ATTENTION The inner element should be replaced every two times the outer element is replaced Daily remove any dust collected in the filter by pressing the rubber cap G. SERVICE INTERVAL Running-in ____________________________ None Cleaning ___________________ Every 10 hours Outer element change ______ Every 500 hours Inner element change _____ Every 1000 hours Page D-10 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 MAINTENANCE ■ D-3.7 CAB AIR FILTER Every six months clean the air filter in the cab. Replace the cartridge if the filtering cloth is damged. 1 Cleaning and changing the cartridge: - Shut the engine down and engage the parking brake. - Pull out the filter A located to the left of the driving place. - Clean the filter bowl. - Clean the filter cartridge and replace in case of damage. ATTENTION Do not, at any times, dry-clean the filters. Use some water and/or solvent. ■ D-3.8 ENGINE COOLING CIRCUIT The cooling radiator is lubricated with the engine oil and does not need any maintenance. Page D-11 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 MAINTENANCE ■ D-3.9 CHECKING THE OIL LEVEL IN THE TANK DANGER Fine jets of hydraulic oil under pressure can penetrate the skin. Do not use your fingers, but a piece of cardboard to detect oil leaks. Check the hydraulic oil level (visually) through the special level fitted into the tank. When necessary, add new oil through filler . CAUTION Check the oil level with handler set to transfer position (lowered boom and retracted telescopic element). SERVICE INTERVAL Running-in _________ Within the first 10 hours Ordinary ____________________ Every 50 hours If oil must be changed, proceed as follows: 1 Stop the machine on a level ground and make sure the parking brake is engaged. 2 Release the pressure from the hydraulic circuit. 3 Place a container of suitable size under the drain plug, placed in the lower part of the reservoir, and collect any oil leaks. 4 Remove the drain plug and allow oil to flow out into the container. 5 Remove the inspection cover of tank . 6 Carefully wash the tank with Diesel oil and blow a jet of compressed air. 7 Refit the drain plug and the inspection cover. 8 Add new oil by making sure that it matches the recommended type indicated in paragraph D-5.2.2. until it is level with . PROTECT THE ENVIRONMENT SERVICE INTERVAL Running-in ____________________________ None Ordinary ________________ Every 1000 hours Page The handling and disposing of used oils can be ruled by local or national regulations. Address to authorised centres. D-12 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 MAINTENANCE ■ D-3.10 CHANGING THE OIL FILTER CANISTERS ON THE INTAKE LINE ■ D-3.10.1 Transmission oil filter Every 50 hours, check the clogging degree of the filtering element using the vacuometer . The indexed scale of the vacuometer is divided into 3 areas: 1 - Green area: Normal condition 2 - Yellow area: Replace the filter as soon as possible 3 - Red area: Shut the engine down to prevent damage to the hydraulic system. Change the filter and/or check for the fault reasons. IMPORTANT 40 30 50 15 20 20 10 60 25 5 Hydraulic oil filter cartridges cannot be cleaned or washed and refitted. They must be replaced with new ones of the type recommended by the manufacturer (see par. D5.2.2). 10 30 70 76 in Hg cm Hg PROTECT THE ENVIRONMENT 0 The handling and disposing of used oils can be ruled by local or national regulations. Address to authorised centres. To change the hydraulic oil filter element on the suction line, proceed as follows: 1 Stop the machine on a level ground and engage the parking brake. 2 Place a container of suitable size under the filter to collect any oil leaks, then close cock . 3 Remove the filtering element using a wrench. 4 Change the filtering element, then, before fitting a new one, thoroughly clean and grease both seat and gasket. 5 Hand-tighten and re-open cock . IMPORTANT When changing the oil, drain it when it is still hot and the polluting substances are in suspension. SERVICE INTERVAL Running-in ____________________________ None Ordinary __________________ Every 500 hours When the dashboard indicator switches on Page D-13 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 MAINTENANCE ■ D-3.10.2 Auxiliary circuits oil filter To change the hydraulic oil filter cartridge of the service circuits, proceed as follows: 1 Stop the machine on a level ground and engage the parking brake. 2 Remove the inspection hatch and unscrew the oil filter fitted inside the tank. 3 Check the tank is clean, then fit a new filtering element and refit the inspection hatch. 4 Check the oil level within the tank. Add new oil, if necessary. SERVICE INTERVAL Running-in ____________________________ None Ordinary __________________ Every 500 hours Page D-14 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 MAINTENANCE D-3.11 OIL LEVEL IN THE DIFFERENTIAL GEARS AND THE REDUCER ■ D-3.11.1 Front and differential gears To check the oil level in the front and rear differential gears: • Stop the machine on a level ground and engage the parking brake. • Loosen level plug and check if oil is level with the hole. • If necessary, add new oil through the hole of the level plug until it comes out. • Refit and tighten plug . For the oil change: • Place a container of suitable size under drain plug . • Loosen the drain plug and the level plug and allow oil to flow out from the differential gears. • Refit and tighten drain plug . • Add new oil through plug until it is level with the hole. • Refit and tighten level/filler plug. SERVICE INTERVAL Running-in _________ Within the first 10 hours Ordinary __________________ Every 250 hours ■ D-3.11.2 Reducer To check the oil level in the reducer • Stop the machine on a level ground and engage the parking brake. • Loosen level plug and check if oil is level with the hole. • If necessary, add new oil through the hole of the level plug until it comes out. • Refit and tighten plug . For the oil change: • Place a container of suitable size under drain plug . • Loosen the drain plug and the level plug and allow oil to flow out from the reduction gear. • Refit and tighten drain plug . • Add new oil through plug until it is level with the hole. • Refit and tighten plug . SERVICE INTERVAL Running-in _________ Within the first 10 hours Ordinary __________________ Every 250 hours Page D-15 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 MAINTENANCE ■ D-3.12 OIL LEVEL IN THE (front/rear) WHEEL REDUCTION GEARS PROTECT THE ENVIRONMENT To check the oil level within the wheel reduction gears: • Stop the machine on a level ground and ensure the parking brake is engaged and plug finds on the horizontal axis. • Clean the plug all around, then remove it and check if oil is level with the hole. • If necessary, add new oil through hole until it is level. • Refit the plug. For the oil change: • Stop the machine and ensure the plug is oriented along the vertical axis. • Place a container of suitable size under the reduction gear plug. • Unscrew plug and drain any oil from the reduction gear. • Rotate the wheel by 90° until the plug finds again on the horizontal axis. • Add new oil through hole . • Refit and tighten plug . The handling and disposing of used oils can be ruled by local or national regulations. Address to authorised centres. IMPORTANT When changing the oil, drain it when it is still hot and the polluting substances are in suspension. SERVICE INTERVAL Running-in _________ Within the first 10 hours Ordinary __________________ Every 250 hours Page D-16 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 MAINTENANCE D-3.13 SHAFTING ALIGNMENT During operation, the alignment of the front and rear axles of the machine can be subject to variations. This can depend on an oil blow-by from the steering control circuit, or on a steering of both axles when front and rear wheels are not perfectly aligned. 80 40 80 40 120 °C 120 °C 01234567 To fix this problem, rather than checking the alignment visually, follow the procedure below: F 1) Move to a solid and level ground N R 2) Set the steering selection switch 14 to “four-wheel steer” (pos. 2) � � � 3) Rotate the steering up to its stop (either to the right or to the left) 4) Set the steering selection switch to “two-wheel steer” (pos. 0) 5) Rotate the steering up to its stop (turn in the same direction as above) � 6) Reset the steering selection switch to “four-wheel steer” (pos. 2) 7) Rotate the steering (to the side opposite to point 3) so that the rear axle reaches its stop 8) Reset the steering selection switch to “two-wheel steer” (pos. 0) 9) Rotate the steering (to the same side as in point 7) so that the front axle reaches its stop 10) Reset the steering selection switch to “four-wheel steer” (pos. 2) Now the wheels should be re-aligned. SERVICE INTERVAL Running-in ____________________________ None Ordinary ___________________ When necessary Page D-17 Document 57.0004.9200 - Rev. 0 - 09/2004 � � Handler with telescopic boom TX 66-22 MAINTENANCE ■ D-3.14 ADJUSTING THE SLIDING PADS OF THE BOOM SECTIONS Any boom section is fitted with adjustable pads located on the four sides of the profile. These pads are secured to both fixed and mobile part of every section. All pads can be adjusted by the special shims supplied by TEREXLIFT upon demand. Adjusting the pads: • Remove or loosen the screws fixing the pads in relation to type of shims used (with or without slots). • Fit the necessary amount of shims. • If the residual thickness of the pad is insufficient or near the maximum wearing limit, renew the pad. • Tighten the screws fixing the pads at the recommended torque (see below). Use a dynamometric wrench. Tightening torques of the pad screws in relation to the screw diameter Screws M10 Nm 30 Screws M14 Nm 50 Tightening torques higher than those recommended can cause the break of the pad or of the locking threaded bush. ATTENTION Pads must compulsorily be replaced if the residual thickness of the plastic layer with respect to the iron bush fixing the block is equal or inferior to 1 mm. Max. wearing thickness SERVICE INTERVAL Minimum 1 mm Running-in ____________________________ None Ordinary ___________________ When necessary Page D-18 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 MAINTENANCE ■ D-3.15 CHECKING THE SAFETY DEVICES ■ Checking the block valves (every 3 months). The piloted blocking valves allow to held the load in position in case of burst of a flexible hose. To check the efficiency of a valve, proceed as follows: • Load a weight near the maximum payload (2500 kg roughly) onto the boom. • Raise the load some centimetres above the ground (max 10 cm). To check the valve on the telescope extension cylinder move the boom to maximum height and extend it some centimetres. • Loosen the oil hoses to the cylinder of which you are checking the valve with caution. During the check, the oil will flow out of the hoses and the load shall remain blocked in position. Should that not be the case, the valve must be replaced. Contact TEREXLIFT Technical Service. DANGER - Wear safety glasses Wear safety gloves Wear safety shoes Wear suitable working clothes Use guards against leaks of oil at high pressure Do the check in a free space with barriers all around to keep non-authorised people away During the check proceed with extreme caution. Ensure that the part to be checked is in safe condition and that the action generated does not result in an uncontrolled movement of the machine Page D-19 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 MAINTENANCE ■ Checking the machine start control (at every use) Attempt to start the engine with the forward or reverse gear put. The engine must not start. If the engine starts, contact the TEREXLIFT Technical Service. Repeat the operation putting first one gear, then the other. Page D-20 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 MAINTENANCE D-4 ELECTRICAL SYSTEM DANGER DANGER • Battery electrolyte contains sulphuric acid. It can burn you if it touches your skin and eyes. Always wear goggles and protective gloves, and handle the battery with caution to prevent spillage. Keep metal objects (watch straps, rings, necklaces) clear of the battery leads, since they can short the terminals and burn you. • Before disconnecting the battery, set all switches within the cab to OFF. To disconnect the battery, disconnect the negative (-) lead from the frame earth first. To connect the battery, connect the positive (+) lead first. Recharge the battery far from the machine, in a well-ventilated place. Keep out of items which can produce sparks, of naked flames or lit cigarettes. Do not rest metal objects onto the battery. This can result in a dangerous short especially during a recharge. Because the electrolyte is highly corrosive, it must never come in contact with the frame of the handler or electric/electronic parts. If the electrolyte comes in contact with these parts, contact the nearest authorised assistance centre. All maintenance interventions must be carried out with engine stopped, parking brake engaged, working attachments on the ground and gearbox lever in neutral. DANGER • When raising a component for maintenance purposes, secure it in a safe way before carrying out any maintenance. • • DANGER • • Before any operation on hydraulic lines or components, make sure there is no residual pressure. For this purpose, stop the engine, engage the parking brake and operate the control levers of the distributors (in both working directions alternately) to release the pressure from the hydraulic circuit. • DANGER D-4.1 BATTERY • Check the electrolyte level every 250 working hours; if necessary, add distilled water. • Ensure the fluid is 5÷6 mm above the plates and the cell levels are correct. • Check the cable clips are well secured to the battery terminals. To tighten the clips, always use a box wrench, never pliers. • Protect the terminals smearing them with pure vaseline. • Remove the battery and store it in a dry place, when the machine is not used for a long time. Page Risk of explosion or shorts. During the recharge, an explosive mixture with release of hydrogen gas forms. DANGER Do not add sulphuric acid; add only distilled water. D-21 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 MAINTENANCE D-4.2 FUSES AND RELAYS The electrical system is protected by fuses placed in the driving cab, on the left. Before replacing a blown fuse with a new one having the same amperage, find out and rectify the fault. ■ Rif. Circuito Amp. F25 Not used 10 F26 Not used 10 F27 Not used 10 F28 Not used 25 F29 Spare fuses Fuses Ref. F1 Circuit Amp. Power supply: interior lamp, emergency switch, turn signals +30 15 F2 Power supply: relay K04 7,5 F3 Optional 15 F4 Front right/rear left position lights, license plate lights, position lights indicator, engine oil temperature indicator 5 Front left/rear right position lights, fuel gaugehourmeter-warning lamps lighting, engine oil cooling temperature indicator light, fan switch, lights selection switch 5 F5 F14 F28 F13 F27 10 F12 F26 Left high beam, High beam warning lamp 10 F11 F25 F10 Horn 15 F11 Windscreen washer kit 10 F10 F24 F12 Optional 5 F9 F23 F13 Optional 5 F8 F22 F14 Optional 7,5 F7 F21 F15 Preheating control unit power supply F16 Not used 15 F6 F20 F17 Not used 15 F5 F19 F18 Not used 15 F4 F18 F19 Not used 7,5 F3 F17 F20 Not used 10 F21 Not used 10 F2 F16 F22 Not used 10 F1 F15 F23 Not used 7,5 F24 Not used 5 F6 Right low beam 7,5 F7 Left low beam 7,5 F8 Right high beam F9 5 Page D-22 Document 57.0004.9200 - Rev. 0 - 09/2004 F29 F29 F29 F29 INT K5 K10 K4 K9 K3 K8 K2 K7 K1 K6 Handler with telescopic boom TX 66-22 MAINTENANCE ■ Fuse box relays Ref. K01 K02 K03 K04 K05 K06 K07 K08 K09 ■ Circuit Starting enabling command Forward speed enabling command Inhibition with brake pedal stepped down Overload warning system control unit enabling command Reverse speed enabling command Overload warning system solenoid valve enabling command 1st and 2nd speed control relay Shaft stop control unit K08 power relay F14 F28 F13 F27 F12 F26 F11 F25 F10 F24 F9 F23 F8 F22 Amp F7 F21 F6 F20 F5 F19 F4 F18 F3 F17 F2 F16 F1 F15 Engine compartment fuses and relays Ref. Circuit F30 Preheating control unit maxifuse 70 F31 System protection fuse 50 A02 Preheating control unit K11 Start relay • • • • Do not use fuses having a higher amperage than that recommended, since they can damage the electric system seriously. If the fuse blows after a short time, look for the fault source by checking the electric system. Always keep some spare fuses for an emergency. Never try to repair or short blown fuses. Make sure the contacts of fuses and fusesockets ensure a good electric connection and are not oxidised. Page D-23 Document 57.0004.9200 - Rev. 0 - 09/2004 INT K5 K10 K4 K9 K3 K8 K2 K7 K1 K6 A02 F30 F31 K11 ATTENTION • F29 F29 F29 F29 Handler with telescopic boom TX 66-22 MAINTENANCE ■ D-4.3 12V DC LAMPS (ONLY WITH GLASS KIT INSTALLED) Use • • • • • • • • • Voltage Mount type Front low/high beam ............................................................ 12 V ....................... P45t Front position lights ............................................................. 12 V ..................... BA 9s Side/tail turn signals ............................................................ 12 V ................... BA 15s Stop lights and rear position lights ...................................... 12 V ................. BAY 15d Beacon - Work lights (OPTIONAL) ....................................... 12 V .......................... H3 Dashboard indicators and cab lighting ................................ 12 V ................ W 2x4,6d Interior lamp ......................................................................... 12 V ................. SV 8,5-8 License plate lights .............................................................. 12 V ................... BA 15s Back-up lamps ..................................................................... 12 V ................... BA 15s CAUTION When switched on, lamps get hot. Before touching a lamp with your fingers, let it cool down. IMPORTANT Never touch the bulb of halogen lamps (mount type H3) with your fingers: this may damage the lamp (use of a clean cloth or a paper tissue). If you touch it accidentally, thoroughly clean with a paper tissue and some ethyl alcohol. Page D-24 Document 57.0004.9200 - Rev. 0 - 09/2004 Power ................. 45/40 W ........................ 3 W ...................... 21 W ................... 21/5 W ...................... 55 W ..................... 1,2 W ........................ 5 W ........................ 5 W ....................... 21W Handler with telescopic boom TX 66-22 MAINTENANCE D-5 REFUELLING ■ D-5.1 REFUELLING Part Diesel engine Fuel tank Hydraulic system tank Front differential gear with reduction gear Front differential gear Front wheel reduction gears Rear wheel reduction gears Brake oil tank Product Engine oil Diesel fuel Hydraulic oil Oil Oil Oil Oil Hydraulic oil Capacity (litres) 11 + 3.5 60 120 6 5 1.5 + 1.5 0.7 + 0.7 0.1 Product specifications see par. D-5.2.1 D-5.2.3 D-5.2.2 D-5.2.2 D-5.2.2 D-5.2.2 D-5.2.2 D-5.2.2 ■ D-5.2 PRODUCT SPECIFICATIONS ■ D-5.2.1 Engine oil Use the oil recommended by the Diesel engine Manufacturer (see the relevant handbook delivered with the machine). At the delivery, the machine is refilled with: SHELL RIMULA 15W-40 ■ D-5.2.2 Lubrication oils and relevant filtering elements Refill the machine with following lubricants: Use Product Definition Power divider-Differential gears-Reduction gears FUCHS TITAN GEAR LS 85 W-90 API GL-5 LS / GL-5 Hydraulic system and brakes SHELL TELLUS T 46 DENISON HF-1 DIN 51524 part 3 Cat. HV ATTENTION Never mix different oils: this may result in troubles and component breaks. ■ Filtering elements: Filter Flow l/1' Filtering Code Transmission oil filter Auxiliary circuit oil filter (inside the tank) MPS 150 STR 100/1 10 µ 60 µ 09.4604.0001 09.4604.0004 Page D-25 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 MAINTENANCE ■ D-5.2.3 Fuel Use only Diesel fuel with less than 0.5% sulphur content, according to the specifications of the diesel engine operation handbook. ATTENTION In cold climates (temperature under -20°C) use only “Arctic” type Diesel fuel, or oil-diesel fuel, or oildiesel fuel mixtures. The composition of the latter can vary in relation to the ambient temperature up to max. 80% oil. ■ D-5.2.4 Grease For the machine greasing, use: • Lithium-based Vanguard LIKO grease, type EP2 When greasing by pump • Graphitized SHELL grease, type GR NG 3 When greasing by brush • INTERFLON FIN GREASE LS 2 For the telescopic boom sliding blocks ATTENTION Avoid mixing greases of different type or features and do not use greases of lower quality. Page D-26 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 FAULTS AND TROUBLESHOOTING Section E FAULTS AND TROUBLESHOOTING TABLE OF CONTENTS E-1 FAULTS AND TROUBLESHOOTING .............................................................. E-2 E-1.1 Fault - Cause - Solution ................................................................................. E-2 Page E-1 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 FAULTS AND TROUBLESHOOTING E-1 FAULTS AND TROUBLESHOOTING This chapter represents a practical guide for the operator for fixing the most common failures and, at the same time, detecting those interventions which must be carried out by qualified technical engineers. If you are unsure about anything, do not carry out operations on the machine, but call in a skilled technician. DANGER Any repair work, maintenance or troubleshooting must be carried out with machine stopped, boom in rest position or laid on the ground, parking brake engaged and ignition key removed. E-1.1 Fault - Cause - Solution DASHBOARD DOES NOT SWITCH ON • The 50A fuse F31 supplying power to the dashboard is blown (engine compartment) • Battery disconnected • Replace the fuse • Battery down • Battery cut-out switch OFF • Connect the battery using the relevant switch • Check the battery • Switch it on ENGINE DOES NOT START Starter does not run • Speed selector switch not in neutral position • Battery down • Battery cut-out switch OFF • Set the speed selector switch in neutral position • Recharge or replace the battery • Switch it on ENGINE DOES NOT START Starter runs, but engine does not start • • • • • • • • Fuse F15 blown No fuel Diesel fuel filter clogged Diesel fuel hose empty (fuel used up) • Solenoid valve - engine stop MACHINE DOES NOT MOVE • Speed selector switch in neutral • Parking brake engaged • Fuse F23 blown Check the fuse Refuel See DEUTZ engine operator manual Refuel, then refer to DEUTZ engine operator manual • Check the solenoid valve; replace, if necessary • Set the speed selector switch correctly • Disengage • Check the fuse; replace, if necessary THE MACHINE DRIVE IS NOT ENOUGH • Hydraulic oil filter clogged • Replace the filter NO SELECTION OF THE STEERING MODE • Fuse F20 controlling the steering selection blown • “ROAD/JOBSITE” switch set to “ROAD” • Replace the fuse • No “ROAD/JOBSITE” selection • Check and replace fuse F20, if necessary “ROAD” FUNCTION ON, EVEN WHEN SELECTING THE “JOBSITE” FUNCTION Page E-2 Document 57.0004.9200 - Rev. 0 - 09/2004 • Set to "JOBSITE" Handler with telescopic boom TX 66-22 FAULTS AND TROUBLESHOOTING NO BOOM LOWERING AND EXTENSION, NO HOLDING FRAME TILTING • Fuse blown • Emergency button ON THE HYDRAULIC OIL THERMOMETER DOES NOT WORK • This is normal, when the outside temperature is low and/or the machine is used for short periods, since the hydraulic oil cannot warm up over 40÷50°C THE PARKING BRAKE LIGHT DOES NOT LIGHT UP • Fuse blown • Check and replace fuse F2, if necessary BOOM DOES NOT MOVE • Fuse blown • Check and replace fuse F22, if necessary • Set to “CAB” • “ROAD/JOBSITE” switch set to “ROAD” • Emergency button ON • Replace fuses F2 and/or F24 • Reset the button • Reset the button ATTENTION In case of faults not listed in this chapter, address to the TEREXLIFT Technical Assistance, your nearest authorised workshop or dealer. Page E-3 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 FAULTS AND TROUBLESHOOTING NOTES ......................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... ..................................................................... Page E-4 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPTIONAL ATTACHMENTS Section F OPTIONAL ATTACHMENTS TABLE OF CONTENTS F-1.1 Shovel ................................................................................................... F-3 F-1.2 Cereal shovel ......................................................................................... F-4 F-1.3 Fixed hook on plate ............................................................................... F-5 F-1.4 Extension jib .......................................................................................... F-6 F-1.5 Forks with hydraulic side-shift .............................................................. F-7 Page F-1 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPTIONAL ATTACHMENTS INTRODUCTION This section provides information on the optional interchangeable attachments, especially manufactured for the handlers. Use only genuine attachments, described in this section, after having read their features thoroughly and understood their use. To install and remove the attachments, follow the instructions supplied in the OPERATION section, par. C-5.4. DANGER When replacing interchangeable attachments, keep any person clear of the working area. DANGER Mounting optional attachments, and especially the extension jib, can change the centre of gravity of the machine. Before handling a load, check its weight and compare it with the values on the load charts. The weight of the used attachment must always be deducted from the rated payload. ■ Procedure to connect hydraulic lines: • • • Couple the new attachment and lock it hydraulically. Disconnect the quick couplings of the attachment locking cylinder and connect them to the false connectors to prevent them from getting dirty. Connect the feeding hoses of the new attachment to the quick couplings previously set free. When the new attachment has two hydraulic motions like, for instance, the pole and pipe planter, a flow selecting valve shall be installed on the machine or the attachment and operated from the cab by means of switch 20. Page F-2 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPTIONAL ATTACHMENTS ■ F-1.1 Application Quick-coupling fitted attachment for moving soil, sand, debris, cereals, etc. SHOVEL Code TX 66-22 Litres 500 Safety Strictly obey the general safety precautions given in section B “SAFETY”. 59.0200.0000 Operation ATTENTION When using a shovel, load the material only when the boom is completely retracted and push against the heap with straight wheels. To load/unload the material, operate the rotation lever of the attachment holding plate. Maintenance Visually check the shovel for damage before using it. Technical data Capacity litres 500 A Width mm 1850 B Length mm 760 H Height mm 700 - Weight kg 290 ATTENTION Attachment suitable for moving loose material. Do not use for digging operations. Page F-3 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPTIONAL ATTACHMENTS ■ F-1.2 Application Quick coupling attachment for loading cereals or inert materials, etc. CEREAL SHOVEL Code TX 66-22 Litres 800 Safety Strictly obey the general safety precautions given in section B “SAFETY”. 59.0200.1000 Operation ATTENTION When using a shovel, load the material only when the boom is completely retracted and push against the heap with straight wheels. To load/unload the material, operate the rotation lever of the attachment holding plate. Maintenance Visually check the shovel for damage before using it. Technical data Capacity litres 800 A Width mm 1850 B Length mm 800 H Height mm 1150 - Weight kg 350 ATTENTION Attachment suitable for moving loose material. Do not use for digging operations. Page F-4 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPTIONAL ATTACHMENTS ■ F-1.3 Application Quick-coupling fitted attachment for lifting loads by means of special slings. FIXED HOOK ON PLATE Payload Code TX 66-22 2600 kg 59.0700.0000 Safety Strictly obey the general safety precautions given in section B “SAFETY”. Do not oscillate the load. Do not drag hooked loads. Lift the load before extending the boom. Operation Fork the hook and hold it in position by means of the locking cylinder. All loads must be bridled with special textile slings or chains in compliance with all pertinent regulations. To handle the load, raise and rotate the telescopic boom of the handler. Maintenance Visually check the hook for damage before using it. Check the safety catch is in good working order. Technical data Payload kg 2600 Width mm 920 Length mm 615 Height mm 500 Weight kg 120 IMPORTANT Make sure this attachment can be used in the destination country of the machine. In Italy, this attachment must be enrolled at ISPESL and submitted to yearly test. Application must be submitted directly by the user. Page F-5 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPTIONAL ATTACHMENTS ■ F-1.5 Application Quick-coupling fitted attachment for maintenance interventions at high working heights. EXTENSION JIB Code Safety Strictly obey the general safety precautions given in section B “SAFETY”. Never lift wrongly slung loads. Avoid abrupt acceleration or deceleration. Avoid load oscillations, and especially do not move the load from the vertical pull line. Do not pull crosswise and do not tow. TX 66-22 400 kg 59.0800.0000 Operation To change the working height, operate the rotation lever of the attachment holding plate. Maintenance Visually check the jib for damage before using it. Check the safety catch is in good working order. Daily grease the joints using the greasing gun. Characteristics - Payload kg 400 A Length mm 2100 B Width mm 920 H Height mm 630 kg 115 - Weight IMPORTANT Make sure this attachment can be used in the destination country of the machine. In Italy, this attachment must be enrolled at ISPESL and submitted to yearly test. Application must be submitted directly by the user. Page F-6 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPTIONAL ATTACHMENTS ■ F-1.6 FORKS WITH HYDRAULIC SIDE-SHIFT Application Quick-coupling fitted attachment for handling palletised loads with possibility of shifting the load to the side by ± 100 mm. Safety Strictly obey the general safety precautions given in section B “SAFETY”. • Do not load loose materials • Do not move superposed pallets Operation To adjust the tilting, operate the rotation lever of the attachment holding plate. To side-shift, operate the attachment locking lever after connecting the feeding lines of the new attachment to the quick couplings (see page F-2). Maintenance Visually check the attachment for damage before using it. Check for hydraulic oil leaks. Daily grease the joints using a greasing gun, and smear the sliding guides with graphitized grease. Machine Code TX 66-22 59.0600.0000 Technical data Payload kg Width Length Height (with protection) Weight Stroke Fork attachments 2600 mm mm mm kg mm 1240 1600 1000 180 ± 100 FEM 2 Page F-7 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 OPTIONAL ATTACHMENTS Intentionally blank page Page F-8 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 TABLES AND DOCUMENTS ENCLOSED Section G TABLES AND DOCUMENTS ENCLOSED TABLE OF CONTENTS G-1 TORQUE WRENCH SETTING ............................................................... G-2 G-2.1 Load Chart with forks ............................................................................ G-3 G-3.1 Wiring diagram - Fuses and relays ........................................................ G-4 G-5 Routine check schedule-Safety devices ............................................... G-5 Page G-1 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 TABLES AND DOCUMENTS ENCLOSED G-1 TORQUE WRENCH SETTINGS Dxp Pre-loading (N) Torque wrench setting (Nm) 4.8 8.8 10.9 12.9 4.8 8.8 10.9 12.9 M 4 x 0,7 1970 3930 5530 6640 1,5 3,1 4,3 5,2 M 5 x 0,8 3180 6360 8950 10700 3 6 8,5 10,1 M6x1 4500 9000 12700 15200 5,2 10,4 14,6 17,5 M 8 x 1,25 8200 16400 23100 27700 12,3 24,6 34,7 41,6 M8x1 8780 17600 24700 29600 13 26 36,6 43,9 M 10 x 1,5 13000 26000 36500 43900 25,1 50,1 70,5 84,6 M 10 x 1,25 13700 27400 38500 46300 26,2 52,4 73,6 88,4 M 12 x 1,75 18900 37800 53000 63700 42,4 84,8 119 143 M 12 x 1,25 20600 41300 58000 69600 45,3 90,6 127 153 M 14 x 2 25800 51500 72500 86900 67,4 135 190 228 M 14 x 1,5 28000 56000 78800 94500 71,7 143 202 242 M 16 x 2 35200 70300 98900 119000 102 205 288 346 M 16 x 1.5 37400 74800 105000 126000 107 214 302 362 M 18 x 2,5 43000 86000 121000 145000 142 283 398 478 M 18 x 1,5 48400 96800 136000 163000 154 308 434 520 M 20 x 2,5 54900 110000 154000 185000 200 400 562 674 M 20 x 1,5 60900 122000 171000 206000 216 431 607 728 M 22 x 2,5 67900 136000 191000 229000 266 532 748 897 M 22 x 1,5 74600 149000 210000 252000 286 571 803 964 M 24 x 3 79100 158000 222000 267000 345 691 971 1170 M 24 x 2 86000 172000 242000 290000 365 731 1030 1230 M 27 x 3 103000 206000 289000 347000 505 1010 1420 1700 M 27 x 2 111000 222000 312000 375000 534 1070 1500 1800 M 30 x 3,5 126000 251000 353000 424000 686 1370 1930 2310 M 30 x 2 139000 278000 391000 469000 738 1480 2080 2490 IMPORTANT Sensor maximum driving torque: 15 Nm. Page G-2 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 TABLES AND DOCUMENTS ENCLOSED G-2.1 LOAD CHART WITH FORKS - TX 66-22 25 TX 66-22 CAPACITY CHART 67 deg E 60 deg D 20 C 50 deg B A 40 deg 66 00 30 deg lb 550 0 lb 15 4400 lb 10 3300 lb ft 10 deg 3000 lb 5 2700 lb 20 deg 0 deg 0 -3 deg E D C B A Forward reach 3 15 10 0 5 Page G-3 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 TABLES AND DOCUMENTS ENCLOSED G-3.1 WIRING DIAGRAM - FUSES AND RELAYS Ref. F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 F14 F15 F16 F17 F18 F19 F20 F21 F22 F23 F24 F25 F26 F27 F28 F29 ■ Circuit Amp. Power supply: interior lamp, emergency switch, turn signals +30 Power supply: relay K04 Optional Front right/rear left position lights, license plate lights, position lights indicator, engine oil temperature indicator Front left/rear right position lights, fuel gaugehourmeter-warning lamps lighting, engine oil cooling temperature indicator light, fan switch, lights selection switch Right low beam Left low beam Right high beam Left high beam, High beam warning lamp Horn Windscreen washer kit Optional Optional Optional Preheating control unit power supply Not used Not used Not used Not used Not used Not used Not used Not used Not used Not used Not used Not used Not used Spare fuses 15 7,5 15 F14 F28 F13 F27 F12 F26 F11 F25 F10 F24 F9 F23 F8 F22 F7 F21 F6 F20 F5 F19 F4 F18 F3 F17 F2 F16 F1 F15 5 5 7,5 7,5 10 10 15 10 5 5 7,5 5 15 15 15 7,5 10 10 10 7,5 5 10 10 10 25 F30 Circuit INT K5 K10 K4 K9 K3 K8 K2 K7 K1 K6 RELAYS Ref. K01 K02 K03 K04 K05 K06 K07 K08 K09 Circuit Starting enabling command Forward speed enabling command Inhibition with brake pedal stepped down Overload warning system control unit enabling command Reverse speed enabling command Overload warning system solenoid valve enabling command 1st and 2nd speed control relay Shaft stop control unit K08 power relay Engine compartment fuses and relays Ref. F29 F29 F29 F29 A02 F30 F31 K 11 Amp Preheating control unit maxifuse 70 F31 System protection fuse 50 A02 Preheating control unit K11 Start relay Page G-4 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 TABLES AND DOCUMENTS ENCLOSED G-5 ROUTINE CHECK SCHEDULE - SAFETY DEVICES Page Micro 5 Micro 4 Micro 3 Micro 2 Micro 1 Block valve 9 Block valve 8 Block valve 7 Block valve 6 Block valve 5 Block valve 4 Block valve 3 Block valve 2 Date Block valve 1 COMPONENT G-5 Document 57.0004.9200 - Rev. 0 - 09/2004 Result/Notes Positive Negative Signature ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ Handler with telescopic boom TX 66-22 TABLES AND DOCUMENTS ENCLOSED Table key explanation: Block valve 1 Block valve on lifting cylinder Block valve 2 Block valve on fork balance cylinder Block valve 3 Block valve on telescope extension cylinder Block valve 4 Block valve on attachment moving cylinder Block valve 5 Block valve on attachment locking cylinder Block valve 6 Block valve 7 Block valve 8 Block valve 9 Micro 1 Micro 2 Micro 3 Micro 4 Micro 5 SAR + Display EMERGENCY Joystick button Page G-6 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 TABLES AND DOCUMENTS ENCLOSED Intentionally blank page Page G-7 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 TABLES AND DOCUMENTS ENCLOSED Intentionally blank page Page G-8 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 TABLES AND DOCUMENTS ENCLOSED Intentionally blank page Page G-9 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 TABLES AND DOCUMENTS ENCLOSED Intentionally blank page Page G-10 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 TABLES AND DOCUMENTS ENCLOSED Intentionally blank page Page G-11 Document 57.0004.9200 - Rev. 0 - 09/2004 Handler with telescopic boom TX 66-22 TABLES AND DOCUMENTS ENCLOSED Intentionally blank page Page G-12 Document 57.0004.9200 - Rev. 0 - 09/2004
