Download WARRANTY Varislicer TM Model 2003

DIAGNOSTIC MODE
Diagnostic mode gives you the ability to trouble shoot the Vari-Slicer. Diagnostic mode
is a series of manually operated independent tests which can be entered as follows.
With the power OFF, depress and hold the START and STOP buttons.
Turn the power ON while the above buttons are depressed.
Hold START and STOP buttons until the slice buttons begin to flash on and off.
Release all buttons and follow the next step quickly.
Within three seconds, while lights are still flashing, press and release the
hidden button located to the left of the #1 button, you are now in Diagnostic Mode.
Select the specific tests using the numbered buttons. The START button must be
pressed to initiate a particular test and should be pressed each time a new selection is
made.
Turn the machine OFF for several seconds to reset it for normal operation.
TEST 1: Jog Mode Test
The pusher can be moved to the left by pressing the START button or to the right
by pressing the STOP button. If the "End Travel" or "Home" proximity sensor is
made, the motor will stop immediately. This will indicate the proximity sensor is
operating correctly. releasing the START or STOP button will allow the motor to be
restarted.
TEST 2: Arm Test - (DOORS MUST BE CLOSED)
The gearmotor can be energized by pressing and holding the START button for
three seconds. Continuing to hold the Start button for an additional three seconds
will engage the arm clutch making the arm move down and up through a cycle. As
long as the Start button is depressed the arm will continue to cycle every three
seconds. During each of these cycles the input LED #I3 should go off and on
once. If the LED remains either off or on then the "Knife Up" sensor must be
adjusted so that the LED in on only when the arm is in the up position.
Rev. 10-1-96
2003320005-6
MODEL 2003 VARIABLE THICKNESS BREAD SLICER
REPLACEMENT PARTS LIST
ITEM NO.
001
002
005
006
007
008
009
010
01 1
012
013
101
101
102
103
104
201
202
203
204
205
206
207
208
209
210
21 1
212
213
214
215
217
218
219
220
222
223
224
225
226
227
228
229
Rev. 06-10-99
PART DESCRIPTION
Cover-Electrical
Track-Crumb Tray
Tray-Crum b
Plate-Face
Stop-Cover
Bumper
Frame-Main
Spacer-Angle
Angle-Table Support
Bumper-Rubber
Stiffener
Motor-Brake 112 HP
Motor-Brake 314 HP
Key
Sheave 3L, 2-Grooves 1.5 OD
Belt-V 3L230
Block-Pivot Outside
Bearing-Ball
Ring-Retaining #N5000-137
Shaft-Drive
Pulley-Timing Belt
Sheave-3L, 2-Grooves 3.882 OD
Ring-Retaining #5100-62
Side-RH Arm
Side-LH Arm
Spacer-Aluminum Tube
Trunnion
Flag
Washer-Special
Holddown
Bearing-Bronze Flange
Ring-Retaining #5100-50
Spring-Extension
Belt-Timing 300L075
Spindle-Blade
DiskICollar
Washer-Special
Knife-Scalloped
Rod-Connecting
Screw-Shoulder 112 X 1-114
Cover-Top
Cover-Bottom
Bearing-Bronze Thrust
PART NUMBER
2003-0021
2003-0038
2003-0037
2003-0003
2001-0111
2001-0112
2003-0001
2003-0034
2003-001 1
5902-0021
2003-0054
6301-3633
6301-561 1
4384-0406-1 5
2003-0070
5601-1 033
2001-0041
5250-0387
5840-1 026
2001-0047-1
2003-0044
2003-0071
5840-1 128
2003-0046-1
2003-0047
2003-0050
2003-0052
2003-0053
2003-0058
2003-0064
5254-31 90
5840-1 125
7021-4005
5601-3341
2001-0072-1 01
2001-0073-001
2001-0074
7107-7056
2003-0027
5842-8545
2003-0048
2003-0049
5254-3507
MODEL 2003 VARIABLE THICKNESS BREAD SLICER
Parts List Continued
ITEM NO.
805
806
807
808
809
809
810
810
811
811
812
813
813
814
814
816
817
818
819
820
82 1
822
823
824
828
829
831
842
850'
858
858
859
875'
876
877
878
901
902
903
904*
* Not Shown on Drawings
Rev. 10-31-96
PART DESCRIPTION
Subpanel-Microprocessor
Control-Microprocessor
Supply-Power
Potentiometer-5K (115 VAC only)
Relay-4 Pole 3A (115 VAC)
Relay-4 Pole 3A (230 VAC)
Contactor-3 Pole (115 VAC)
Contactor-3 Pole (230 VAC)
Relay-Overload (115 VAC)
Relay-Overload (230 VAC)
Diode-Zener
Varistor (115 VAC)
Varistor (230 VAC)
Suppressor-RC (115 VAC)
Suppressor-RC (230 VAC)
Plug-Screw Connector 8 Pin
Plug-Screw Connector 10 Pin
Plug-Screw Connector 4 Pin
Socket-14 Pin
Control-DC (115 VAC only)
Resistor-Control (115VAC only)
Din Rail
Duct-Wire
Cover-Wire Duct
Block-Terminal
Block-Ground Terminal
Barrier-End
Sensor-Prox.
Harness-Switch W/O Switch
Relay9 Pole (115 VAC)
Relay9 Pole (230 VAC)
Socket-8 Pin
Harness-Main
Cord-AC Motor
Cord-Clutch
Cord-Gearmotor
Scanner-Bread
Switch-Prox. (HomelEnd)
Switch-Prox. (Door)
Harness-Prox. Switches
PART NUMBER
2002-0002
5712-0402
5746-5687
5746-6000
5749-5624
5749-5666
5749-8274
5749-8284
5750-1252
5750-1254
5754-1045
5754-1070
5754-1073
5754-1083
5754-1084
5765-7468
5765-7469
5765-7467
5770-2834
6309-6000
6309-6014
5770-7166
5771-6260
5771-6253
5770-7270
5770-7271
5770-7272
5757-8860
2003-0024-001
5749-5671
5749-5670
5770-2833
2003-0025-001
2003-0025-002
2003-0025-003
2003-0025-004
2003-0026-001
2003-0026-002
2003-0026-003
2003-0026-004
.
445 Sixth St., N.W., Grand Rapids, Michigan 49504-5298
(616) 45&7711
800125%3893. Fax: (616) 4565820
WARRANTY
Varislicer TM Model 2003
Product Suitability
This product is intended for the slicing of bread and bread related products only. The specific suitability for
slicing certain bread types is to be determined at the time of sale in conjunction with an authorized Oliver
Products Company representative.
Parts
Oliver Products Company warrants that if any part of the equipment (other than a part not manufactured by
Oliver) proves to be defective (as defined below) within 3 years afler shipment, and if Buyer returns the defective
part to Oliver Products Company within one year, Freight Prepaid Oliver Products Company's plant in Grand
Rapids, MI, then Oliver Products Company shall, at Oliver Product Company's option, either repair or replace
the defective part, at Oliver Products Company's expense.
Labor
Oliver Products Company further warrants that equipment properly installed, maintained, and cleaned in
accordance with our special instructions, which proves to be defective in material or workmanship under normal
use within 2 years from installation or actual shipment date, which ever comes first, will be repaired by Oliver
Products Company or an Oliver Products Company Authorized Service Dealer, in accordance with Oliver
Products Company's published Service Schedule.
For purposes of this warranty, a defective part or defective equipment is a part or equipment which is found by
Oliver Products Company to have been defective in materials or workmanship, if the defect materially impairs the
value of the equipment to Buyer. Oliver Products Company has no obligation as to parts or components not
manufactured by Oliver Products Company, but Oliver Products Company assigns to Buyer any warranties
made to Oliver Products Company by the manufacturer thereof.
This warranty does not apply to:
1. Damage caused by lack of cleaning, shipping, accident, misuse, or acts of God.
2. Damage resulting from improper installation or alteration.
3. Equipment not cleaned daily, misused, abused, altered, not maintained on a regular basis, operated
carelessly, or used in abnormal conditions.
4. Equipment used in conjunction with products of other manufacturers unless such use is approved by
Oliver Products Company in writing.
5. Normal wear parts including but not limited to: blades, belts, brakes, clutches.
6. Periodic maintenance of equipment and other adjustments required due to installation, set-up, or normal
wear.
7. Losses or damage resulting from malfunction.
THlS WARRANTY IS NOT EFFECTIVE UNLESS THE INSTALLATION/WARRANTY REGISTRATION HAS
BEEN COMPLETED, SIGNED, AND RETURNED TO OLIVER PRODUCTS COMPANY WITHIN 15 DAYS
FROM DATE OF INSTALLATION.
The foregoing warranty is in lieu of all other warranties expressed or implied AND OLIVER PRODUCTS
COMPANY MAKES NO WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE REGARDING
THE EQUIPMENT COVERED BY THlS WARRANTY. Oliver Products Company neither assumes nor
authorizes any person to assume for it any other obligations or liability in connection with said equipment.
OLIVER PRODUCTS COMPANY SHALL NOT BE LIABLE FOR LOSS OF TIME, INCONVENIENCE,
COMMERCIAL LOSS, INCIDENTAL OR CONSEQUENTIAL DAMAGES.