Download Electricity Meters

Electricity Meters
PCE-DM12
PCE-DM32
DM-9960
Digital multimeter with auto-ranging
Digital multimeter with CAT III 1000 V
Multimeter with Peak measurements and
frequency up to 40 MHz
This digital multimeter is a new device with a rugged double plastic
enclosure equipped with a large LCD with high contrast. It meets CAT
III / 600 V / IN 61010-1 standard. The PCE-DM12 has an automatic
ranging selection and it has a basic AD accuracy of 0.5 %. Its durability
and reliability makes it capable of being used in laboratories, in
research and development or in technical service.
This meter is an automatic digital multimeter meeting the CAT III /
1000 V security standard. It has a high contrast LCD with an
illumination key. The warning and security indications displayed on
the display helps you detect negative polarity, faulty fuses and lower
tension connections. It also indicates if voltage must be disconnected
in the case of passive functions.
•
•
•
•
•
•
•
•
•
• Several functions: AC/DC V, AC/DC A, Ohm, Frequency,
Capacitance and Temperature, measuring duty cycle, diode
test and continuity check
• Rugged enclosure with ingress protection against water jet and
impact
• Maintenance of value / relative value
• Auto shut-off
• Diode test
• Overload protection
• ISO calibration certificate (optional)
This digital multimeter possesses automatic and manual ranging
selection, as well as a dual indicator with a maximum value up to
3999 and an analogical bar graph with 40 segments. It offers you
several possibilities in your measurements, like Peak value for
impulses of >1 ms. This multimeter has protection against complete
input and it meets CAT III 1000 V standard. It has an automatic ranging
selection for: DCV, ACV, DCA, ACA, ohms, diode measurements,
continuity check, capacity, frequency and temperature.
Large easy to read LCD, even in adverse conditions
Several functions
Auto-ranging
Data Hold function
Auto shut-off
Safety design
Diode test
Continuity check
ISO calibration certificate (optional)
Analogue bar graph display with 40 segments
Battery life indicator
Peak, Data Hold, minimum and maximum values
Measures relative value
Diode test
Auto-ranging
ISO calibration certificate (optional)
Technical specifications
DCV
600 V; ±0.5 %
ACV
600 V; ±1.2 %
DCA
10 A; 600 V; ±2.5 %
ACA
10 A; 600 V; ±3.0 %
Ohm
2 / 20 / 40 MΩ; ±0.8 %
Capacitance
200 µF; ±3.0 %
Frequency
10 MHz; ±1.5 %
Temperature
760 °C; ±3.0 %
Duty Cycle
9.99 %; ±1.2 %
Power
9 V battery
Dimensions
150 x 70 x 48 mm
Weight
255 g
Approvals
EN61010-1; CAT III / 600V
Technical specifications
DCV
400 mV/ 4/ 40/ 400/ 1000 V;
±0.5 %; +2 dgt. - 100 µV
ACV
400 mV/ 4/ 40/ 400/ 750 V;
±0.8 %; +3 dgt. - 100 µV
DCA
400 µA/ 4/ 40/ 400 mA/ 20 A;
±1.2 %; +8 dgt. - 100 nA
ACA
400 µA/ 4/ 40/ 400 mA/ 20 A;
±1.5 %; +10 dgt. - 100 nA
Ohm
400 Ω / 4/ 40/ 400 kΩ / 4/ 40 MΩ;
±1.0 % +2 dgt. - 100 mΩ
Capacitance
40/ 400 nF/ 4/ 40/ 100 µF;
±3.5 % +5 dgt.- 10 pF
Frequency
10/ 100 Hz/ 1/ 10/ 100 kHz/ 1/ 10 MHz;
±1.2 % +2 dgt. - 1 mHz
Temperature
-20 to +1000 °C; ±3 % +2 dgt. - 0.1 °C
Power
9 V battery
Dimensions
88 x 197 x 41 mm
Weight
390 g
Approvals
IEC1010-1, UL1244, CATIII 1000V/CATIV 600V
Technical specifications
DCV
400 mV / 4 / 40 / 400 / 1000 V
±0.8 % +1dgt.; 100 µV
ACV
400 mV/ 4 / 40 / 400 / 1000 V
±1.0 % +2 dgt.; 100 µV
DCA
0,4 / 4 / 40 / 400 mA /10 A
±1.5 % +2 dgt.; 0,1 µA
ACA
0,4 / 4 / 40 / 400 mA / 10 A
±1.5 % +2 dgt.; 0,1 µA
Ohm
400 Ω / 4 / 40 / 400 kΩ / 4 / 40 MΩ
±1.5 % +2 dgt.; 0,1 Ω
Capacitance
4 / 40 / 400 nF/ 4 /40 / 400 µF / 4 / 40 mF
±3 % +1 dgt.; 1 pF
Frequency
4 / 40 / 400 kHz / 4 / 40 MHz
±0.5 % +2 dgt ; 1 Hz
Temperature
-20 to +750 °C; ±1 % +2 °C
Power
2 AAA batteries (1.5 V)
Dimensions
88 x 185 x 40 mm
Weight
350 g
Approvals
IEC-1010-1; CAT III 1000 V
Contents
PCE-DM12 multimeter, test leads, type-K thermo-element, battery
and user’s manual
Contents
PCE-DM32 multimeter, soft case, test leads, battery, type-K
thermoelement, cable, software and user’s manual
Contents
DM-9960 digital multimeter, test leads with alligator clips,
batteries and user’s manual
Model No.
PCE-DM12
Model No.
PCE-DM32
Model No.
DT-9960
Description
Digital multimeter
Optional accessories
CAL-DMM
ISO certificate
50
•
•
•
•
•
•
•
Description
Digital multimeter
Optional accessories
RS232-USB
RS-232 to USB adaptor
CAL-DMM
ISO certificate
Description
Digital multimeter
Optional accessories
CAL-DMM
ISO certificate
Electricity Meters
W-20-TRMS
PCE-DM 22
Multimeter with RS-232 interface,
software and effective value measurement
TRUE RMS multimeter with memory, RS-232 interface and software
This digital multimeter indicates to you the test leads that you will
need to take your measurement depending on the measurement range
selected. This meter has a display with symbols for each function,
a warning symbol for faulty fuses and a discharge warning symbol.
As an additional function it has an audible alarm which indicates all
errors that occur. It also offers you the possibility to measure capacity,
frequency and temperature.
This handheld multimeter is an instrument which will cover almost all your needs. It determines DCV, ACV, DCA, ACA and resistance values
with great precision, as well as capacitance, frequency, revolutions and temperature. It also has diode test and continuity check functions.
You will be able to transfer the readings to a PC or portable via the software that is included in the delivery. The integrated data logger allows
you make long-term measurements of machines and electric systems. This handheld multimeter is delivered with factory calibration and
if you want, you can purchase a laboratory calibration and an optional ISO certificate (wither with your order or with your annual recalibration).
• Large, high contrast, 3¾ digit LCD
• RS-232 C interface and software for
Windows 95/98/2000/NT/ME/XP
• Ingress protection for dust and water
• Overload protection
• Effective value measurement
• Relative value
• Data Hold
• Audible alarm
• Diode test
• Manual or automatic ranging
• Measures operating cycle in %
•
•
•
•
•
•
•
•
•
Auto-ranging
High basic DC Voltage accuracy
DCV, ACV, DCA, ACA, resistance, capacity, frequency, temperature, revolutions
Diode test, continuity check
Peak function (1 ms)
Relative value / Min / Max / Hold
Internal memory (32,000 values)
RS-232 interface, cable, software
ISO calibration certificate (optional)
Technical specifications
Voltage DC
400 mV
±0.3 % + 5 dgt.
100 µV
4V
±0.1 % + 5 dgt.
1 mV
40 V
±0.1 % + 5 dgt.
10 mV
400 V
±0.1 % + 5 dgt.
100 mV
1000 V
±0.5 % + 5 dgt.
1V
Voltage AC
400 mV
±1.5 % + 5 dgt.
100 µV
4V
±1.0 % + 5 dgt.
1 mV
40 V
±1.0 % + 5 dgt.
10 mV
400 V
±1.0 % + 5 dgt.
100 mV
700 V
±1.0 % + 5 dgt.
1V
Current DC
400 µA
±1.2 % + 10 dgt.
0,1 µA
4 mA
±1.2 % + 10 dgt.
1,0 µA
40 mA
±1.5 % + 10 dgt.
10 µA
400 mA
±1.5 % + 10 dgt.
100 µA
20 A
±2.0 % + 10 dgt.
10 mA
Current AC
400 µA
±1.5 % + 10 dgt.
- 0,1 µA
4 mA
±1.5 % + 10 dgt.
- 1 µA
40 mA
±1.5 % + 10 dgt.
- 10 µA
400 mA
±1.5 % + 10 dgt.
- 100 µA
20 A
±2.0 % + 10 dgt.
- 1 mA
Resistance
400 Ω / 4 / 40 / 400 kΩ / 4 / 40 MΩ
±1 % + 5 dgt. - 100 mΩ
Capacitance
4 / 400 nF / 4 / 40 / 100 µF
±3 % + 10 dgt. - 10 pF
Frequency
10 Hz ... 10 MHz
±0.1 % + 2 dgt. - 10 mHz
Temperature
-20 to +1370 °C
±3 % + 5 dgt. - 0.1 °C
Overcurrent safety
CAT II 1000 V / CAT III 600 V
Power
9 V battery
Dimensiones
88 x 178 x 33 mm
Weight
315 g
Technical specifications
Voltage DC
Contents
W-20-TRMS multimeter, software, RS-232 interface, battery, soft
case, test leads, type-K thermo-element, spare fuse and user’s
manual
Contents
PCE-DM 22 multimeter, test leads. type-K temperature probe, battery, soft case, RS-232 cable, software and user’s manual
Model No.
W-20-TRMS
Model No.
PCE-DM 22
Description
W-20-TRMS multimeter
Optional accessories
RS232-USB
RS-232 to USB adaptor
CAL-DMM
ISO certificate
Voltage AC
Current DC
Current AC
Other measurement ranges
Memory / Interface
Software
Power
Dimensions / Weight
Approvals
400 mV
4V
40 V
400 V
1000 V
±0.3 % of reading + 2 dgt
±0.3 % of reading + 2 dgt
±0.3 % of reading + 2 dgt
±0.3 % of reading + 2 dgt
±0.3 % of reading + 2 dgt
45 to 500 Hz
400 mV
±0.5 % of reading + 5 dgt
4V
±0.5 % of reading + 5 dgt
40 V
±0.5 % of reading + 5 dgt
400 V
±0.5 % of reading + 5 dgt
750 V
±0.5 % of reading + 5 dgt
400 µA
±0.8 % of reading. + 2 dgt
4000 µA
±0.8 % of reading + 2 dgt
40 mA
±0.8 % of reading + 2 dgt
400 mA
±0.8 % of reading + 2 dgt
10 A
±1.0 % of reading + 2 dgt
45 Hz to 500 Hz
400 µA
±1.3 % of reading + 5 dgt
4000 µA
±1.3 % of reading + 5 dgt
40 mA
±1.3 % of reading + 5 dgt
400 mA
±1.3 % of reading + 5 dgt
10 A
±1.5 % of reading + 5 dgt
Resistance:
400 Ω; 4/ 40/ 400 kΩ; 40 MΩ
Capacitance: 4/40/400nF; 4/40/400µF; 4/40mF
Frequency:
4/ 40/ 400 kHz; 4/ 40 MHz
RPM:
4/ 40 kRPM; 4/ 40/ 400 MRPM
Temperature: -50 to +1000 °C
internal, up to 32,000 values / RS-232
included in the delivery
9 V battery
198 x 86 x 38 mm / 430 g
IEC 1010-1, CAT III 1000 V
0.1 mV
1 mV
10 mV
100 mV
1V
500 Hz to 1 kHz
±1 % + 5 dgt
±1 % + 5 dgt
±1 % + 5 dgt
±1 % + 5 dgt
±1.2 % + 5 dgt
500 Hz to 1 kHz
±1.6 % + 5 dgt
±1.6 % + 5 dgt
±1.6 % + 5 dgt
±1.6 % + 5 dgt
±1.8 % + 5 dgt
±0.6 % of reading + 2 dgt
±1.9 % of reading + 20 dgt
±0.5 % of reading + 1 dgt
±0.5 % of reading + 1 dgt
±1.0 % of reading + 2°C
0.1 mV
1 mV
10 mV
100 mV
1V
0.1 µA
1 µA
10 µA
100 µA
10 mA
0.1 µA
1 µA
10 µA
100 µA
10 mA
0,1 Ω
1 pF
1 Hz
0.01 RPM
1°C
Description
Multimeter with data logger
Optional accessories
USB-DM 22
USB cable for the PCE-DM 22 multimeter
CAL-DMM
ISO certificate
51
Electricity Meters
PCE-UT803
PCE-UT804
True RMS bench multimeter with several functions, USB- / RS-232
interface and software
High precision True RMS bench multimeter with several functions, datalogger, USB-/ RS-232 interface and software
The PCE-UT803 is a high performance and low cost multimeter. It comes with LCD display, shows the
information. It is designed by a high-tech team. This instrument combines the bench-top and system
features which provides a versatile solution for your testing requirements now and in the future. The
capacitance is 6 nF / 60 nF / 600 nF / 6µ / 60 µF / 600 µF / 6 mF, precision: ±(2 % +5). There is USB
interface.
The PCE-UT804 is a high performance and low cost clamp multimeter. It comes with LCD display,
shows the information. It is designed by a high-tech team. This instrument combines the bench-top
and system features which provides a versatile solution for your testing requirements now and in the
future. The capacitance is 40 nF / 400 nF / 4 µF / 40 µF / 400 µF / 4 mF / 40 mF, precision: ±(1 % +20).
There is USB interface.
• Auto-ranging
• Several functions: AC/DC V, AC/DC A, Ohm, Frequency, Capacitance and Temperature, measuring
duty cycle, diode test and continuity check
• Effective value measurement
• Min- / max- / hold-function
• USB and RS-232 interface
• Data cable and software included
• Frequency range up to 60 MHz
• ISO calibration certificate (optional)
• Highest precision
• Auto-ranging
• Several functions: AC/DC V, AC/DC A, Ohm, Frequency, Capacitance and Temperature, measuring
duty cycle, diode test and continuity check
• Effective value measurement up to 100 kHz
• Relative value
• Datalogger for 9,999 values with sampling rate from 1 s to 255 s
• Frequency range up to 400 MHz
• USB and RS-232 interface
• Data cable and software included
• ISO calibration certificate (optional)
Technical specifications
Voltage DC
600 mV
±0.3 % of reading +2 dgt
0.1 mV
6V
±0.3 % of reading +2 dgt
1 mV
60 V
±0.3 % of reading +2 dgt
10 mV
600 V
±0.3 % of reading +2 dgt
100 mV
1000 V
±0.5 % of reading +3 dgt
1V
Voltage AC
600 mV
±0.6 % of reading +5 dgt
0.1 mV
6V
±0.6 % of reading +5 dgt
1 mV
60 V
±0.6 % of reading +5 dgt
10 mV
600 V
±0.6 % of reading +5 dgt
100 mV
750 V
±1.2 % of reading +3 dgt
1V
Current DC
600 µA
±0.5 % of reading +3 dgt
0.1 µA
6000 µA
±0.5 % of reading +3 dgt
1 µA
60 mA
±0.5 % of reading +3 dgt
10 µA
600 mA
±0.8 % of reading +3 dgt
100 µA
10 A
±1.2 % of reading +3 dgt
10 mA
Current AC
600 µA
±1.0 % of reading +5 dgt
0.1 µA
6000 µA
±1.0 % of reading +5 dgt
1 µA
60 mA
±1.0 % of reading +5 dgt
10 µA
600 mA
±1.0 % of reading +5 dgt
100 µA
10 A
±2.0 % of reading +6 dgt
10 mA
Resistance
600 Ω; 6/ 60/ 600 kΩ; 6/ 60 MΩ
±0.5 to 1.2 % +2 dgt
Capacitance
6/ 60/ 600 nF; 6/ 60/ 600 µF; 6 mF
±2.0 to 5.0 % +5 dgt
Frequency
6/ 60/ 600 kHz; 6/ 60 MHz
±0.1 % +3 dgt
Temperature
-40 °C to +1000 °C
±1.0 % +3 dgt
Sampling rate
2 to 3 / s
Continuity check
< 30 Ω
Diode test
< 2,7 V / 1 mA
Interface
USB and RS-232
Software
included
Display
LCD with backlight
Power
230 V / 50 Hz or 6 batteries (1.5 V)
Dimensions / Weight
240 x 105 x 310 mm / 2000 g
Approvals
IEC 1010-1, CAT I 1000 V / CAT II 600 V
Technical specifications
Voltage DC
400 mV
±0.025 % of reading +5 dgt
0.1 mV
4V
±0.05 % of reading +5 dgt
1 mV
40 V
±0.05 % of reading +5 dgt
10 mV
400 V
±0.05 % of reading +5 dgt
100 mV
1000 V
±0.05 % of reading +5 dgt
1V
Voltage AC
4V
±0.4 % of reading +30 dgt
1 mV
40 V
±0.4 % of reading +30 dgt
10 mV
400 V
±0.4 % of reading +30 dgt
100 mV
750 V
±1.0 % of reading +30 dgt
1V
Current DC
400 µA
±0.1 % of reading +15 dgt
0.01 µA
4000 µA
±0.1 % of reading +15 dgt
0.1 µA
40 mA
±0.15 % of reading +15 dgt
1 µA
400 mA
±0.15 % of reading +15 dgt
10 µA
10 A
±0.5 % of reading +30 dgt
1 mA
Current AC
400 µA
±1.0 % of reading +30 dgt
0.01 µA
4000 µA
±1.0 % of reading +30 dgt
0.1 µA
40 mA
±1.0 % of reading +30 dgt
1 µA
400 mA
±1.0 % of reading +30 dgt
10 µA
10 A
±2.5 % of reading +40 dgt
1 mA
Resistance
400 Ω; 4/ 40/ 400 kΩ; 4/ 40 MΩ
±0.3 to 1.0 % +40 dgt
Capacitance
40/ 400 nF; 4/ 40/ 400 µF; 4/ 40 mF
±1.0 to 5.0 % +20 dgt
Frequency
40/ 400 Hz; 4/ 40/ 400 kHz; 4/ 400 MHz ±0.01 % +8 dgt
Temperature
-40 °C to +1000 °C
±1.0 % +30 dgt
TRMS Frequency range
up to 100 kHz
Memory
9999 values
Sampling rate
1 to 255 s (adjustable)
Data readout
about Display or Software
Interface
USB and RS-232
Software
included in the delivery
Display
triple LCD with bargraph and backlight
Power
230 V / 50 Hz or 6 batteries (1.5 V)
Dimensions / Weight
240 x 105 x 310 mm / 3000 g
Approvals
IEC 1010-1, CAT I 1000 V / CAT II 600 V
Contents
PCE-UT803 multimeter, test leads, alligator clips (large and small), temperature probe (type K), adaptor,
batteries, USB cable, RS-232 cable, Software and user’s manual (For U.K. customers: incl. U.K. AC Mains
Power Adaptor)
Contents
PCE-UT804 multimeter, test leads, alligator clips (large and small), temperature probe (type K), adaptor,
batteries, USB cable, RS-232 cable, Software and user’s manual (For U.K. customers: incl. U.K. AC Mains
Power Adaptor)
Model No.
PCE-UT803
Model No.
PCE-UT804
Description
Bench multimeter
Optional accessories
CAL-DMM
ISO certificate
52
Description
High precision bench multimeter
Optional accessories
CAL-DMM
ISO certificate
Electricity Meters
PCE-DC4
PCE-DC3
CM-9940
1000 A AC digital clamp meter
2/80 A AC/DC mini clamp meter with
high resolution
600 A AC/DC digital clamp meter
This digital clamp meter measures currents without contact and it
has a rugged unbreakable rubber enclosure with ingress protection
against fire. Its special design allows you use it in areas with difficult
access. All its functions have an overload protection.
This mini clamp meter is ideal for non-contact AC/DC voltage
measurements. It has a built-in white flashing LED to illuminate the
area being measured. Its small dimensions make it useful in areas
with difficult access. The large illuminated display guarantees
values can be read even in dark areas, like in distribution frames.
With our digital clamp meter you will be able to measure continuous
and alternating current besides using the basic functions of
continuous and alternating voltage, resistance, frequency, continuity
check and diode tests. It is ideal in the technical sector due to its
reduced diameter of 30 mm. It has overload protection for all
measurement ranges.
• Large 3¾ digit LCD (17 mm),
maximum indicator: 3999
• Data Hold freeze the current value
• AC current up to 1000 A
• Voltage measurement up to 600 V AC/DC
• Resistance, frequency, capacitance, duty cycle, and
temperature measurements
• Diode test and continuity check
• Manual and automatic ranging
• Maximum diameter of 31 mm
• Auto shut-off
• ISO calibration certificate
(optional)
•
•
•
•
•
•
•
•
•
32/3 digit LCD with backlight
AC / DC current measurement up to 80 A
Data logger
DCA Zero function
Non-contact AC voltage detector
Auto-ranging
Auto shut-off
18 mm clamp opening
ISO calibration certificate (optional)
• 4 digit LCD, 11 mm
maximum 5000 (frequency range)
• Measurements up to 600 A AC/DC
• Data Hold, continuity check and relative value
• 30 mm clamp opening
• ISO calibration certificate (optional)
Technical specifications
DCV
400 mV / 4 / 40 / 400 / 600 V;
±0.8 % + 3 dgt. – 100 µV
ACV
400 mV / 4 / 40 / 400 / 600 V;
±1.8 % + 5 dgt. – 100 µV
ACA
40 / 400 / 1000 A; ±2.5 % + 5 dgt. – 10 mA
Ohmios
400 Ω / 4 / 40 / 400 kΩ / 4 / 40 MΩ;
±1.0 % + 4 dgt. – 100 mΩ
Capacitance
40/400 nF / 4/40/100 µF; ±3 % + 5 dgt – 10 pF
Frequency
5/50/500 Hz /5/50/500 kHz /5/10 MHz;
±1.2 % + 2 dgt. – 1 mHz
Temperature
-50 to +1000 °C; ±3 % + 5 °C - 0.1 °C
Clamp opening
31 mm maximum diameter
Dimensions
80 x 229 x 49 mm
Weight
303 g
Approvals
IEC-1010-1; CAT III 600 V
Technical specifications
ACA
2 A; ±3 % + 8 dgt. - 1 mA
80 A; ±3 % + 8 dgt. - 100 mA
DCA
2 A; ±2.8 % + 8 dgt. - 1 mA
80 A; ±2.8 % + 8 dgt. - 100 mA
Voltage control
100 to 600 VAC
(without contact)
Clamp opening
18 mm maximum diameter
Dimensions
65 x 164 x 32 mm
Weight
175 g
Technical specifications
DCV
400 mV / 4 / 40 / 400 / 600 V
±1.0 % + 2 dgt. – 0.1 mV
Overload protection
DC 600 V
ACV
400 mV / 4 / 40 / 400 / 600 V
±1.2 % + 5 dgt. – 0.1 mV
Overload protection
AC 600 V
DCA
400 / 600 A; ±2 % + 8 dgt. – 0.1 A
Overload protection
DC 600 V
ACA
400 / 600 A; ±2 % + 8 dgt. – 0.1 A
Overload protection
AC 600 V
Ohm
400 Ω / 4 / 40 / 400 kΩ / 4 / 40 MΩ
±1 % + 5 dgt. up to 400 kΩ,
if not ±3.5 % + 5 dgt. – 0.1 Ω
Overload protection
AC/DC 400 V
Frequency
5 / 50 / 500 Hz / 5 / 50 100 kHz
±1 % + 5 dgt. – 0.001 Hz
Overload protection
AC/DC 250 V
Audible alarm
yes
Diode test
yes
Power
2 batteries (1.5 V)
Dimensions
178 x 64 x 33 mm
Weight
230 g
Approvals
IEC-1010-1, CAT III 600 V
Contents
PCE-DC4, carrying case, test leads, type-K temperature probe,
9 V battery and user’s manual
Contents
PCE-DC3, battery and user’s manual
Contents
CM-9940, carrying case, test leads, batteries and user’s
manual
Model No.
PCE-DC4
Model No.
PCE-DC3
Model No.
CM-9940
Description
1000 A AC digital clamp meter
Optional accessories
CAL-MZ
ISO certificate
Description
80 A AC/DC mini clamp meter
Optional accessories
CAL-MZ
ISO certificate
Description
600 A AC/DC digital clamp meter
Optional accessories
CAL-MZ
ISO certificate
53
Electricity Meters
CM-9930
PCE-EI-3000
PCE-UT232
2000 A AC/DC clamp meter
Flexible clamp meter for leads up to 170 mm
in diameter and 3000 A
3 Phase Power Clamp / Meter / Analyzer with
Computer Interface (USB) and Software
This clamp meter is a versatile instrument with a modern design and
modern technology. It has a rugged enclosure with ingress protection
against breaking and fire and the handle is also protected which
prevents the user from touching the clamp or the internal lead (it offers
maximum security to the user). All measurement ranges have overload
protection.
This special digital clamp meter has a flexible AC current probe for
big lead cables with a diameter up to 170 mm, something that you
could not measure up to now with a normal digital clamp meter. Its
special flexible probe allows it to be used in areas with difficult
access in which it’s impossible to use a typical clamp. It measures
net frequencies, currents up to 3000 A AC and voltages up to
600 V AC like real effective value.
The product is tri-phasic three lines and tri-phasic four lines. This
high effective tool is the best choice for machine analyzing
technicians and electricians in a wide field of industrial applications.
The clamp can store the measured data (upto 99) and can be
transferred to a PC or Portable later on. There are many special
functions such as auto measure, large LCD display etc.
• 4 digit LCD (15 mm),
5000 maximum (frequency range)
• Measurements up to 2000 A AC/DC
• 60 mm clamp opening
• Data Hold, valor efectivo real
• Continuity check
• ISO calibration
certificate (optional)
•
•
•
•
•
•
•
•
•
•
• Measures active / apparent / reactice power, power factor,
phase angle, active energy
• Self calibration function
• Max / Min data capture / data hold display
• Store / recall saved data
• ISO calibration certificate
as option
Technical specifications
DCV
400 mV / 4 / 40 / 400 / 1000 V
±1.0 % + 2 dgt. – 0.1 mV
Overload protection
DC 1000 V
ACV
400 mV / 4 / 40 / 400 / 1000 V
±1.2 % + 5 dgt. – 0.1 mV
Overload protection
AC 1000 V
DCA (direct)
400 µA / 4 / 40 / 400 mA; ±1.2 % + 5 dgt.
(with clamp)
400 / 2000 A; ±2.0 % + 8 dgt.
Overload protection DC 500 mA direct; DC 1000 V clamp
ACA (direct)
400 µA / 4 / 40 / 400 mA; ±1.2 % + 5 dgt.
(with clamp)
400 / 2000 A; ±2.0 % + 8 dgt.
Overload protection AC 500 mA direct; AC 1000 V clamp
Ohms
400 Ω / 4 / 40 / 400 kΩ / 4 / 40 MΩ
±1 % + 5 dgt. up to 400 kΩ,
or ±3.5 % + 5 dgt. – 0,1 Ω
Overload protection
AC/DC 400 V
Frequency
5 / 50 / 500 Hz / 5 / 50 100 kHz
±1 % + 5 dgt. – 0.001 Hz
Overload protection
AC/DC 1000 V
Capacitance
50 / 500 nF / 5 / 50 µF; ±3 % + 5 dgt.
Effective current value
yes
Audible alarm / diodes
yes / yes
Power
9 V battery
Dimensions
255 x 73 x 38 mm
Weight
380 g
Approvals
IEC-1010-1, CAT III 1000 V
Technical specifications
ACA Trms
300 A / 0,1 A 1000 A / 0,1 A 3000 A / 1 A;
±1 % of measurement range
ACV Trms
4.0 to 600 V / 0.1V; ±0.5 % ±5 digit
Frequency
45 to 65 Hz / 0.1 Hz; ±0.2 Hz
Cable lenght dimensions
maximum 170 mm
Minimum bending diameter
minimum 35 mm
Cable probe diameter
14 mm
Display
4+4 digit LCD
Operating conditions
-10 to +85 °C
Power
2 AA batteries (1.5 V)
Dimensions
130 x 80 x 43 mm
Weight
430 g
Technical specifications
ACV TRMS
20 / 100 / 300 / 600 V; ±1.2 % + 5 dgt.
ACV TRMS
40 / 100 / 400 / 1000 A; ±2.0 % +5 dgt.
Active power (P)
0.01 kW to 600 kW; ±3.0 % +5 dgt.
Apparent power (S)
0.01 kVA to 600 kVA; ±3.0 % +5 dgt.
Reactive power (Q)
0.01 kWAr to 600 kVAr; ±4.0 % +5 dgt.
True energy
1 to 9999 kWh; ±3.0 % +2 dgt.
Power factor (PF)
0.3 to 1.00; ±0.02 + 2 dgt.
Phase angle
0 to 360°; ±1.0°
Frequency
20 to 500 Hz
Temperature
-50 to +1300 °C
Memory
99 values
Display
4 digit LCD with analog bargraph
Power
4 batteries (1.5 V)
Dimensions
112 x 39 x 303 mm
Weight
600 g
Contents
CM-9930, test leads, battery and user’s manual
Contents
PCE-EI-3000 flexible clamp meter, batteries and user’s manual
Contents
PCE-UT232 power analyser, 4 x test leads, 4 x alligator clips,
USB cable, software, batteries, carrying case and user’s manual
Model No.
CM-9930
Model No.
PCE-EI-3000
Model No.
PCE-UT232
Description
2000 A AC/DC digital clamp meter
Optional accessories
CAL-MZ
ISO certificate
54
True RMS
3000 A AC direct current / 600 V AC Voltage
4+4 digit LCD
Auto-ranging
Frequency indicator
Fast Peak function (30 µs)
MAX / MIN functions
Auto shut-off
Cable length from probe to instrument: maximum 170 mm
ISO calibration certificate (optional)
Description
3000 A AC digital clamp meter
Optional accessories
CAL-MZ
ISO certificate
Description
Power analyser
Optional accessories
CAL-MZ
ISO certificate
Electricity Meters
PCE-FC25
PCE-FC27
PCE-IT55
10 Hz to 2.6 GHz Frequency counter with
telescopic RF pickup antenna
10 Hz to 2.7 GHz Frequency counter
with RS-232 interface
Insulation tester with three test leads
This frequency counter possesses a microprocessor for frequency,
period, resolution, data hold, relative measurement and memory
(maximum, minimum and average values) functions. Its low
consumption and its large display allow you to work comfortably under
unfavourable light conditions. The telescopic antenna, which is included
in the delivery, makes it possible to measure (only frequency) without
cables, a mobile or stationary transmitter.
We offer you a bench type frequency counter with 8 digit display, a
measurement range from 10 Hz to 2.7 GHz and a time base of
10 MHz with a quartz oscillator controlled by the temperature.
Frequency counter connection guarantees great measurement
results with high accuracy and high sensitivity. Its ease of use and
its versatility makes it very attractive for scientific, laboratory
technicians, communications technicians and engineers. All the
functions are selected through the keypad.
This insulation meter determines the insulation resistance up to
2000 MΩ (for 250, 500 and 1000 V auxiliary voltages). It also offers
the possibility to measure continuous and alternating currents up to
750 V / 1000 V, as well as resistance up to 2 kΩ. It has a continuity
check function and a beep tone for insulation measurements.
Measurement values can be adjusted by pressing a key. This unit
meets DIN 57 411 part 1 / VDE 0411 part 1 standards, which
aremeasurement protection for electronic meters (IEC1010-1) and
DIN VDE 0413 (insulation meters).
•
•
•
•
•
Telescoping RF pickup antenna with BNC connector
Measurement range of 5 to 30 cm
Auto shut-off
It can be connected to a 9 V Vdc adaptor
ISO certificate (optional)
Technical specifications
Measurement range
2500 MHz: 50 MHz ... 2500 MHz
(max. 2600 MHz)
500 MHz: 10 MHz ... 500 MHz
10 MHz: 10 Hz ... 10 MHz
Sensitivity
2500 MHz: <50 mVeff
500 MHz: <50 mVeff
10 MHz: <50 mVeff
Period range
10 Hz to 10 MHz
Sensitivity
<50 mVeff
Time base
4.194 MHz Quartz Crystal
Power
4 batteries (1.5 V)
Dimensions
80 x 173 x 35 mm
Weight
340 g
•
•
•
•
•
•
•
RS-232 serial interface (protocol included)
Self-testing function
Minimum, maximum and average data storage
Input for external frequency
8 digit LCD
Relative period measurements
ISO calibration certificate (optional)
Technical specifications
Ranges
Sensitivity
Period ranges
Sensitivity
Time base
Time base stability /.
temperature
Frequency accuracy
Input connector
Power
Dimensions
Weight
10 Hz to 10 MHz
10 MHz to 500 MHz
100 MHz to 2700 MHz
10 MHz: 30 mVeff
500 MHz: 50 mVeff
2.7 GHz: 50 mVeff
10 Hz to 10 MHz
10 Hz a 9 MHz: 15 mVeff
16.777216 MHz
±1.5 PPM (+10 to +30 °C)
±(2 PPM +1 dgt); +23.5 °C
10 MHz + period: 15 Veff
500 MHz: 4 Veff
2.7 GHz: 4 Veff
6 AA batteries
or a 9 V adaptor
280 x 210 x 90 mm
1200 g
•
•
•
•
•
•
•
Meets IEC1010-1,CAT III 1000 V
Large dual display with backlight
Short-term and long-term measurements with "LOCK"
Over range and battery life indicators
Beep tone for insulation measurements
Auto shut-off
ISO calibration certificate (optional)
Technical specifications
Ranges
insulation: 0 to 200 MΩ / 200 to 2000 MΩ
ACV: 0 ... 750 V
DCV: 0 ... 1000 V
ohms: 0 to 200 Ω / 200 to 2000 Ω
Resolution
insulation: 100 kΩ to 1 MΩ
ACV: 1 V
DCV: 1 V
ohms: 0,1 Ω / 1 Ω
Accuracy
insulation: ±3.5 % ±5 dgts
ACV: ±1.2 % ±10 dgts
DCV: ±0.8 % ±3 dgts
ohms: ±1.0 % ±2 dgts
Test voltage
250 V - 200 MΩ
500 V - 200 MΩ
1000 V - 2000 MΩ
Continuity test
beep: <40 Ω, test current 200 mA
Power
6 AA batteries
Operating conditions
0 to +40 °C / <80 % r.h.
Dimensions
200 x 92 x 50 mm
Weight
700 g
Approvals
IEC10101, CAT III 1000 V
Contents
PCE-FC25 frequency counter, telescopic antenna, control cables,
batteries and user’s manual
Contents
PCE-FC27 frequency counter, 1 test cable kit, 6 batteries and
user’s manual
Contents
PCE-IT55 insulation tester, cables, test leads, jaw alligator clips,
batteries, carrying case and user’s manual
Model No.
PCE-FC25
Model No.
PCE-FC27
Model No.
PCE-IT55
Description
Frequency counter
Optional accessories
CAL-PCE-FC ISO certificate
Description
Frequency counter
Optional accessories
SOFT-LUT
Software and RS-232 cable
CAL-PCE-FC ISO certificate
Description
Insulation tester
Optional accessories
CAL-5500
ISO certificate
55
Electricity Meters
PCE-IT111
PCE-DI 6300
PCE-IT413 & PCE-IT414
Insolation meter (up to 8 GΩ) with a compact
enclosure
Professional insulation tester
High voltage insulation tester up to 10,000V
The insulation meter detects the resistance of insulation up to a
maximum of 8 GΩ (in auxiliary power of 250, 500 and 1000V). The
insulation meter also measures direct current and alternative
current up to a maximum of 950 VDC and 700 VAC, and resistance
up to a maximum of 2 kΩ. It has a tester for energy flow with integrated
acoustic signal. Readings can be retained with the touch of a button.
The device meets these standards: DIN 57 411 part 1/VDE 0411
part 1, counter measures for electronic measing instruments
(IEC1010-1) and DIN VDE 0413 (insulation meters).
This PCE-DI 6300 professional insulation tester is a device with high
insulation measurement performances (according to standard VDE
0413 part) in electrical systems, lead tubes and machines with 100,
250, 500 or 1000V AD voltages.
The PCE-IT413 and PCE-IT414 high voltage insulation testers
belong to a series of very durable meters which are highly accurate
and display 6 digits. It’s ideal for technical employees indoors and
outdoors. One of its advantages is the integral protection circuit which
avoids measurement errors due to current leaks. It has an audible
and visual alarm.
• 2 line and 16 digit LCD
• Automatic polarity indication, range selection and zero reset
• Acoustic signal when there is a discharge to the insulation
meter
• Overcharge protection in continuity tests
• Safety function, power is maintained for only 10 seconds
(can be deactivated)
• Hold function
• ISO calibration certificate (optional)
Technical specifications
Measurement ranges
• Measures according to VDE 0413 part 1
• Insulation test voltage up to 5,000V (model PCE-IT413)
and up to 10,000V (model PCE-IT414)
• High quality and great price
• ISO calibration certificate (optional)
Technical specifications
Insulation
Technical specifications
Models
PCE-IT413
PCE-IT414
DC insulation test voltage 500 / 1,000 /
1,000 / 2,500 /
2,500 / 5,000 V
5,000 / 10,000 V
Insulation ranges
30 GΩ / 500 V
60 GΩ / 1,000 V
60 GΩ / 1,000 V
150 GΩ / 2,500 V
150 GΩ / 2,500 V 300 GΩ / 5,000 V
300 GΩ / 5,000 V 600 GΩ / 10,000 V
Accuracy
±3 %
Voltage output
1 W max.
Insulation resistance between
2000 MΩ / 2000 V
circuit and housing
Static voltage between
7,000 V AC for max. 1 min
circuit and enclosure
AC circuit warning
voltages > 450 V AC
Power
8 batteries (1.5 V)
Dimensions
250 x 110 x 190 mm
Weight
1.5 kg
Approvals
IEC-1010-1; CAT III ; IEC- 1010-1;
EN61010-1; EN50081-1; EN50082-1
Included in the delivery
PCE-IT111, test cables with alligator clips, shoulder strap, batteries
and user’s manual
Contents
PCE-DI 6300, test leads, large jaw clips, belt, batteries and
user’s manual
Contents
PCE-IT413 or PCE-IT414, silicone control cable, high voltage
probe with integrity protection and coaxial relay, batteries and
user’s manual
Model No.
PCE-IT111
Model No.
PCE-DI 6300
Model No.
PCE-IT413
PCE-IT414
Resolution
Accuracy
DC test voltage
Short circuit current
Operating conditions
Power
Dimensions
Weight
Approvals
2 GΩ / 250 V
4 GΩ / 500 V
8 GΩ / 1000 V
DCV: 0 ... 700 V
ACV: 0 ... 950 V
ohms: 0,01 ... 1999 Ω
insulation: 1 / 10 / 100 MΩ
DCV: 1 V
ACV: 1 V
ohms: 0,01 / 0,1 / 1 Ω
insulation.: ±3 %
DC: ±1,5 %
AC: ±1,5 %
ohms: ±2,0 %
250 / 500 / 1000 V
4,0 mA
0 to +55 °C/ 5 to 95 % r.h.
8 x batteries 1.5 V
175 x 85 x 75 mm
655 g
IEC- 1010- 1; EN 61010- 1;
CAT III 700; EN 50081- 1; EN 50082- 1
Description
Insulation meter
Recommended Accessories
CAL-HSI
ISO certificate
56
• Measures according to VDE 0413 part 1
• Multi ranges MΩ
• High voltage insulation measurements; 2.8 mA short
circuit current
• Several voltage insulation measurements
• Insulation / continuity test currents
• Battery life and over range indicators
• Auto-zeroing and automatic discharge
• ISO calibration certificate (optional)
200 MΩ / 100 V
200 MΩ / 250 V
200 MΩ / 500 V
1000 MΩ / 1 kV
Accuracy insulation:
±3 % +1 un / dgt
DC: ±2 % +1 un / dgt
AC: ±1 % +2 un / dgt
resistance: ±4 % +1 un / dgt
DC insulation test voltage 100 / 250 / 500 / 1000 V
Short circuit current
approx. 2.6 to 2.8 mA
AC Voltage
600 V
Input resistance
4.5 MΩ
Resistance
200 Ω
Measurement interval
0.4 s
Operating conditions
0 to 50 °C/ 5 to 95 % r.h.
Power
6 batteries (1.5 V)
Dimensions
160 x 120 x 85 mm
Weight
575 g
Approvals
IEC- 1010- 1; EN 61010- 1;
CAT III 600; EN 50081- 1; EN 50082- 1
Description
Insulation tester
Optional accessories
CAL-HSI
ISO certificate
Description
High voltage insulation tester (5,000 V)
High voltage insulation tester (10,000 V)
Optional accessories
CAL-HSI
ISO certificate
Electricity Meters
PCE-ET 3000
PCE-MO 2001
PCE-MO 2002
Earth resistance voltage tester for building
checks and controls
Waterproof miliohms tester
Highly accurate, battery powered milliohm
tester in a water resistant enclosure
Earth resistance voltage tester measures the lightning rods or lightning
rod earth resistance in buildings. It possesses a hermetically sealed
enclosure and meets securrity standard VDE 0413, which is
necessary for technicians who work outdoors. It is ideal for
measuring ground and lighting rod electrodes, as well as small ground
systems, resistance voltage and continuity leads measurements. The
most modern computation systems reduces to a minimum voltage
and ground electrodes influences.
This miliohms tester has ingress protection against water jets and
can measure resistance from 100 µΩ to 2000 Ω. Measurement values
are displayed on the 3½ digit LCD. To obtain the measurement value
you must place the tester on the object you wish to measure a
continuous current and the milliohms tester measures the voltage
load.
This battery powered milli-ohm tester in a water resistant enclosure
(sealed by a O-ring joint) allows measurement of resistance from
100 µΩ to 2000 Ω. It’s ideal for on-site technicians thanks to it being
battery powered. To detect the measurement value, a constant current
is put through the object being measured and the fall in power of the
object is then determined by ther device.
• Engine coils, generators, transformers, e.g. in parallel,
contiguous or compact computation circuits, switching
equipments and relay measurements
• Chemical binding energy in mines, on planes, tracks, boats, as
well as home and industrial systems
• Cyclic system (Ringbus) pitch controls in home and industrial
environments
• Overhead line checks, maintenance or testing of switchboards,
etc.
• ISO calibration certificate (optional)
•
•
•
•
•
•
•
•
Technical specifications
Range
Resolution
Accuracy
Earth resistance
20 / 200 /
10 / 100 mΩ /
±2%
2000 Ω
1Ω
+2 pos.
AC voltage
0 to 200 V AC
±3%
50/60 Hz
+ 2 pos.
Minimum voltage
0.01 Ω
Current
2 mA / rms
Resistance indication
indicates if electrode resistance
is into the range parameters
Operating conditions
0 to 50°C/ 5 to 95% r.h.
Power
8 batteries (1.5V)
Dimensions
250 x 190 x 120 mm
Weight
1.5 kg
Approvals
IEC-1010-1; CAT III 300 V
Technical specifications
Measurement ranges 0 to 200 mΩ in steps of 100 µΩ /
0 to 2000 mΩ: 1 mΩ /
0 to 20 Ω: 10 mΩ / 0 to 200 Ω: 100 mΩ /
0 to 2000 Ω: 1 Ω
Accuracy
±0.75% of reading ±2 pos. full range
temperature range of -15 to 55°C (for measure
with control cable included in the delivery)
Control current
1 mA (range: 2000 Ω)
10 mA (ranges: 200 / 20 Ω)
Accuracy
±0.1%
Power
230 V AC, 50 / 60 Hz
Dimensions
250 x 180 x 200 mm
Weight
1.35 kg
Approvals
IEC-1010-1; CAT IV 20 V
Technical Data
Measurement ranges
Contents
PCE-ET 3000, 15 m red control wire, 10 m yellow control wire, 5 m
green control wire, earth spikes and user’s manual
Contents
PCE-MO 2001, test and power leads and user’s manual
(For U.K. customers: incl. U.K. AC Mains Power Adaptor)
Contents
PCE-MO 2001, test leads, 8 batteries and user’s manual
Model No.
PCE-ET 3000
Model No.
PCE-MO 2001
Model No.
PCE-MO 2002
•
•
•
•
•
•
•
Frequency test of 820 Hz
Battery life indicator
Overload protection
Data Hold
Security: IEC-1010-1 and CAT III 300 V
3½ digit LCD (max. 2000)
15 m red wire with red plug, 10 m yellow wire, 5 m green
wire; auxiliary earth spikes, batteries and user’s manual
• ISO calibration certificate (optional)
Description
Earth resistance voltage tester
Optional accessories
CAL-ERD
ISO certificate
Description
miliohms tester
Optional accessories
CAL-2001
ISO certificate
Measurement system of 4 conductors
5 measurement ranges
3 test currents with fuse
Overlaod protection
Large display
Information about the resistance of the line being tested
Auto-Hold and Auto shut-off functions
LED to indicate permitted overload limits for Rp, Rc and
temperature
• ISO calibration certificate (optional)
0 ... 200 mΩ in steps of 100 µΩ /
0 ... 2000 mΩ: 1 mΩ /
0 ... 20 Ω: 10 mΩ / 0 ... 200 Ω: 100 mΩ /
0 ... 2000 Ω: 1 Ω
Accuracy
±0.5 % of reading ±2 pos. full range
temperature range of -15 ... +55 °C (for measure
with control cable included in the delivery)
Control current
1 mA (range: 2000 Ω)
10 mA (ranges: 200 / 20 Ω)
100 mA (ranges: 2000 mΩ / 200 mΩ)
Accuracy
±0.1 %
Power supply
8 batteries of 1,5 V
Dimensions
250 x 190 x 110 mm
Weight
1.5 kg
Approvals
IEC-1010-1; CAT IV 20 V
Description
miliohms tester
Optional accessories
CAL-2002
ISO certificate
57
Electricity Meters
TM-10
PCE-123
PCE-OC 1
TV and satellite signal level meter
Multifunction calibrator for
thermocouple and frequency inputs
Handheld Digital Storage Scope Meter /
Oscilloscope with USB-Interface
This TV and satellite signal level meter measures the quality of TV
VHF / UHF signals from an antenna to the customer's IRD. It is compact,
portable and very easy to use, making it the ideal test instrument for
satellite installers. It is very useful for optimising the placement or
orientation of installations. Its large LCD with bar graph shows the
reading of several values, such as frequency, field value, operative
option and the unit of measurement. The metal enclosure provides
good protection of internal systems or outdoor applications.
This precision multifunction calibrator is a device that doesn't need
mains connection and it has a frequency source of 1 Hz to 62.5 kHz
in over 700 steps. You will be able to simulate phase regulation signals
and individual signals in your technical checks and adjustments (MSR).
You will able to check and calibrate all the measurement parameters.
The nominal value indicator allows you to prepare an electrical output
signal. This calibrator also possesses an automatic graduation, set
output percentage steps (0 to 100%) and a direct indication of the
output value.
This programmable universal oscilloscope offers enhanced features
that similar types test instruments on the market todays don`t have.
The most frequent use of the osciloscope is troubleshooting
malfunctioning electronic equipment. One of the advantages is that
the oscilloscope can be used in a frequency range of 5 MHz in real
2-channel-use and shows the signals graphically: where a single
voltmeter may show a totally unexpected voltage, the scope may
reveal that the circuit is oscillating.
•
•
•
•
•
•
•
•
•
TV and satellite signal level measurements
PLL tuning control for frequency selection
Audio level measurement of 4.5 / 5.5 / 6 and 6.5 MHz
Line voltage measurement (70 V)
Rechargeable battery / Auto shut-off
99 favourite channel memory
Peak holder function for detecting maximum input level
Buzzer for acoustic signal strength monitoring
Automatically records selected adjustment
•
•
•
•
•
•
•
•
4 to 20 mA (1 kΩ, 24 V power supply)
0 to 100 mV / 0 to 1 V / 0 to 12 V
K, J, E, T thermocouples (°C and °F)
Frequency range: 1 to 62500 Hz
Basic accuracy: 0.025 %
Easy to use
Step and auto-ramp features
Output 0 to 100 %
(mA, mV, V )
• ISO calibration
certificate (optional)
Dual channel and auto calibration
DC to 5 MHz, 1 MHz oscilloscope band width
Built-in auto ranging true RMS multimeter
PC interface for transferring measurement data and waveform
Backlight display, 132 x 128 pixels
Data hold and run mode
Low battery indicator
ISO calibration certificate
(optional)
Technical specifications
Frequency range
5 to 862 MHz; 250 kHz
Tuning control
PLL control
for frequency
(tuning control of frequency)
Input level range
30 to 120 dB µV; ±3 dB
(0 to +40 °C) -0.1 dB
HF input
F connector
Audio
A: +4.5 MHz / B: +5.5 MHz
C: +6 MHz / D: +6.5 MHz
Frequency range
frequency
resolution
(5 to 862 MHz in steps of 250 kHz)
Memory
video, audio, peak value
Units
dB, µV, DCV, ACV
Power
12 V / 1200 mA
rechargeable batteries
Battery life
3 hours
External power supply
12 V DC, 500 mA
Indicators
frequency, channel, level, dB, µV, ACV, DCV
function, battery level, audio level
(bandwidht) and bar graph
Dimensions
180 x 75 x 150 mm
Weight
1500 g
Technical specifications
mA DC Current (1 kΩ max. load , 24 V power supply)
Range
4 to 20 mA / 0 to 20 mA / 0 to 24 mA
Resolution
1 µA
Accuracy
±0.025 % ±3 µA
mV, V DC Voltage (1 mA power supply)
Ranges / Resolution
0 to 100.00 mV / 10 µV
0 to 10.000 V / 1 mV
0 to 1.0000 V / 100 µV
Accuracy
±0.05 % ±30 µV
±0.05 % ±3 mV
±0,05 % ±300 µV
K, J, E, T Thermocouples
Ranges
-200 to 0 °C and 0 to +1370 °C
Resolution
1 °C
Accuracy
±1.1 °C and ±0.8 °C
Frequency
Ranges
1 to 125 Hz and 126 to 62.5 kHz
Resolution
1 to 125 Hz / 1 Hz 126 to 62.5 kHz
in 604 steps
Accuracy
±0.04 Hz
Power
9 V battery or 6 batteries (1.5 V)
Dimensions
88 x 168 x 26 mm
Weight
330 g
Technical specifications
Contents
TM-10 TV and satellite signal level meter, carrying case, battery
charger, internal batteries and user’s manual (For U.K. customers:
incl. U.K. AC Mains Power Adaptor)
Contents
PCE-123 precision multifunction calibrator, carrying case,
type-K adaptor, batteries, test cables with alligator clips and
user’s manual
Contents
PCE-OC 1 oscilloscope, software, USB cable, test leads, case, holster,
batterie charger, Li-Ion battery and user’s manual
Model No.
TM-10
Model No.
PCE-123
Model No.
PCE-OC 1
Description
TV and satellite signal level meter
Description
Multifunction calibrator
Optional accessories
CAL-123
ISO certificate
58
•
•
•
•
•
•
•
•
Oscilloscope
2
5 MHz DC
25 MS/s (dual) / 50 MS/s (single)
AC, DC
1 MΩ
±3.0 % vertical / ±0.01 % horizontal
16 curves
Multimeter
Ranging
auto, manual
Voltage DC
1000 V DC / ±0.3 % +3 dgt.
Voltage AC
750 V AC (TRUE RMS) /
±0.75 %+ 5 dgt. (50 to 450 Hz)
Resistance
5 / 50 / 500 kΩ / 5 MΩ / ±0.5 % +5 dgt.
Continuity buzzer
1,7 V test voltage
Frequency
100 Hz / 1 / 10 / 100 kHz / 1 / 10 MHz
±0.05 % +5 dgt.
Revolutions
240 to 60,000 r.p.m.
General specifications
Display
132 x 128 pixels
Power
3.7 V Li-Ion battery
or mains power adaptor
Interface
USB
Dimensions / Weight
90 x 195 x 40 mm / 460 g
Approvals
DIN 57 411 / VDE 0411;
IEC 1010; EN 61010; CAT III / 600 V
Input channels
Band width frequency
Sampling rate
Input
Input impedance
Accuracy
Waveform memory
Description
Oscilloscope
Optional accessories
CAL-PCE-OC 1
ISO certificate
PCE-CA 502
Amp clamp adaptor to 1000 A
Electricity Meters
Serie PCE-UT
Digital storage 2 channel oscilloscopes
High performance, 2 channel oscilloscopes with colour display (PCE-UT2025B monochrom display) that are an ideal replacement for upgrade for analogue scopes in service, quality testing, repair and education
environments. The Serie are 2-channel oscilloscopes with 25 MHz up to 250 MHz bandwidth, 250 MS/s up to 500 MS/s sampling rate. With the software you can carry out communication between a computer
and an oscilloscope through serial or USB, and in turn perform remote control. This software also provides testing, waveform and sampling data reading functions to facilitate further signal testing and analysis.
•
•
•
•
•
•
•
•
Up to 500 MS/s real time or 25 GS/s ET sampling rate (depending on model)
PC interface for transferring measurement data, waveform and sampling data reading
5,7 ” colour display, 320 x 240 pixels (PCE-UT 2025B monochrom display)
FFT, ADD, SUB, MULT, DIV and REV maths functions
Extensive cursor measurements
USB and RS-232 interface
Comes with 2 x probes, software and user manual
ISO calibration certificate
(optional)
Technical specifications
Model
PCE-UT 2025B
Band width frequency
25 MHz
Rise Time
<14 ns
Sample rate
250 MS/s
Vertical sensitivity
2 mV to 5 V/div
Record length (max)
1M
Sample rate
real time 500 MS/s to 1 GS/s,
eqivalent: 25 GS/s
Scan time base
20 ns to 50 s/div
Trigger type
Edge, Pulse, Video and Alternate
Automatic waveform
28
measurements
Ports
RS-232
Mathematics
Add, Subtract, Divide,
Reverse and FFT
Memory
1Mb (2x 512k) and 10 settings
Display
Monochrome LCD, 320 x 240,
diagonal 145 mm
Power
100 to 240 V, 45 Hz to 440 Hz
Dimensions
320 x 150 x 130 mm
Weight
4.1 kg
Approvals
CAT II
PCE-UT 2042C
40 MHz
<8.7 ns
500 MS/s to 1 GS/s
2 mV to 5 V/div
1M
real time 500 MS/s to 1 GS/s,
eqivalent: 25 GS/s
10 ns to 50 s/div
Edge, Pulse, Video and Alternate
28
PCE-UT 2082C
80 MHz
<4.5 ns
500 MS/s to 1 GS/s
2 mV to 5 V/div
1M
real time 500 MS/s to 1 GS/s,
eqivalent: 25 GS/s
5 ns to 50 s/div
Edge, Pulse, Video and Alternate
28
PCE-UT 2152C
150 MHz
<2.3 ns
500 MS/s to 1 GS/s
2 mV to 5 V/div
1M
real time 500 MS/s to 1 GS/s,
eqivalent: 25 GS/s
2 ns to 50 s/div
Edge, Pulse, Video and Alternate
28
PCE-UT 2202C
200 MHz
<2.3 ns
500 MS/s to 1 GS/s
2 mV to 5 V/div
1M
real time 500 MS/s to 1 GS/s,
eqivalent: 25 GS/s
2 ns to 50 s/div
Edge, Pulse, Video and Alternate
28
USB Device, USB Host, RS-232
Add, Subtract, Divide,
Reverse and FFT
1Mb (2x 512k) and 10 settings
64 k, full colour LCD, 320 x 240,
diagonal 145 mm
100 to 240 V, 45 Hz to 440 Hz
320 x 150 x 130 mm
4.1 kg
CAT II
USB Device, USB Host, RS-232
Add, Subtract, Divide,
Reverse and FFT
1Mb (2x 512k) and 10 settings
64 k, full colour LCD, 320 x 240,
diagonal 145 mm
100 to 240 V, 45 Hz to 440 Hz
320 x 150 x 130 mm
4.1 kg
CAT II
USB Device, USB Host, RS-232
Add, Subtract, Divide,
Reverse and FFT
1Mb (2x 512k) and 10 settings
64 k, full colour LCD, 320 x 240,
diagonal 145 mm
100 to 240 V, 45 Hz to 440 Hz
320 x 150 x 130 mm
4.1 kg
CAT II
USB Device, USB Host, RS-232
Add, Subtract, Divide,
Reverse and FFT
1Mb (2x 512k) and 10 settings
64 k, full colour LCD, 320 x 240,
diagonal 145 mm
100 to 240 V, 45 Hz to 440 Hz
320 x 150 x 130 mm
4.1 kg
CAT II
Contents
PCE-UT oscilloscope (one of these models), probe x 2 (1x, 10x switchable), software, power cord and english user’s manual
Model No.
PCE-UT 2025B
PCE-UT 2042C
PCE-UT 2082C
PCE-UT 2152C
PCE-UT 2202C
Description
25 MHz Oscilloscope, monochrom Display
40 MHz Oscilloscope, colour Display
80 MHz Oscilloscope, colour Display
150 MHz Oscilloscope, colour Display
200 MHz Oscilloscope, colour Display
Optional accessories
CAL-PCE-UTO
ISO certificate
59
Electricity Meters
PCE-PA6000
PCE-360
Power meter with RS-232 interface
3-Phase power analyser (in real time) with data logger, PC interface and software
PCE-PA6000 power meter is designed for bench use and measures
power, power factor, current, alternating voltage and current,
current and continuous voltage, resistance and frequency. This device
has an RS-232 interface, and with software you will be able to transfer
data to a PC to check and manipulate readings more comfortably.
The PCE-360 power analyser is ideal for measuring power in one or three phases. Its large display shows up to 10 values. You can attach,
at the same time, up to 4 current sensing clamps. The manual option allows you to store 99 readings directly. In data storage mode you
can record up to 20,000 values, making the 3-phase power analyser ideal for long-term analysis. You can transfer the measurements to
a PC for later analysis (includes software and USB cable).
•
•
•
•
•
•
Auto-ranging
Direct power measurement through a probe or power clamp
Data Hold / High / Low alarm functions
Powered by adaptor or batteries
RS-232 interface
ISO calibration certificate (optional)
• Real time control, record and assess
one or three systems
• Current and power measurements
• Power factor and phase angle
• Active, apparent and reactive power
• Harmonics measurements
• Connectors for 4 current sensing clamps
• 512K Data logger (20,000 readings)
• Memory to record up to 99 measurements
• RS-232 interface,
cable for PC and software included
• LCD can dispaly 10 readings
• ISO certificate (optional)
Technical specifications
Power measurement
Technical specifications
Volts measurement (AC)
True power value
Direct measurement
Volts measurement (AC)
with external clamp
adapter
VA measurement
1 W to 6 kW;
1 W;
±1.5 % + 1 dgt.
1 W to 999,9 kW;
1 W;
±1.5 % + 1 dgt.
0.01 VA to 9.999 kVA;
0.01 VA;
±1.5 % +1 dgt.
Power factor (cos φ)
0.00 to 1.00; 0.01; ±1.5 % + 2 dgt.
KWh counter
0.001 Wh to 9999 kWh;
0.001 Wh;
±1 % + 1 dgt.
ACV / DCV
0.1 V to 600 V; 0.1 / 1V; ±1 % +1 dgt.
ACAeff/rms
direct max 10 A; 10 mA, probe
DCAeff/rms
max. 1000 A; 1 A
±1 % + 1 dgt.
ACA with clamp
up to 2000 A (depending on clamp)
Frequency
10.0 ... 999 Hz; 0.1 Hz; 1 % + 1 dgt.
Ohm
1 Ω ... 19.99 kΩ; 1 / 10 Ω; ±1 % +1 dgt.
Power
6 AA batteries (1.5 V)
or adaptor
Dimensions
280 x 210 x 90 mm
Weight
1100 g
Active power (P)
Apparent power (S)
Reactive power (Q)
Energy (true, apparent
and reactive work)
Power factor (PF)
Phase angle
Frequency measurement
Memory
0 to 999.9 Veff / TRUE RMS three inputs with the same
"N" reference point
Resolution:
0.1 V
Accuracy:
±0.3 % of reading + 10 D for >80V powers
Frequency:
50 Hz (not for FU use)
Range:
phase 1 – 3 (0 to 1000 A) / TRUE RMS
range "N" (0 to 250 A) / TRUE RMS
Resolution:
0.1 A
Accuracy:
±0.5 % of reading + 15 D ±1 %
Range:
0 to 999.9 KW
Accuracy:
±1 % of reading + 20 D
Range:
0 to 999.9 KVA
Accuracy:
±1 % of reading + 10 D
Range:
0 to 999,9 KVAR
Accuracy:
±1 % of reading + 20 D
Ranges:
0.0 to 9999 MWh / 0.0 to 9999 Mvarh / 0.0 to 9999 MVAh
Resolution:
0,1 KWh / 0.1 Kvarh / 0.1 KVAh
Accuracy:
±1 % of reading + 20 D
Range:
0.000 to 1.000
Accuracy:
±1 dgt
-0 to 90 °
Range:
40 to 100 Hz / U1 power
Accuracy:
±1 % of reading + 2 D
data logger:
max. 20,000 readings (512 k),
in and out time adjustable
manual memory:
99 readings
5 s, 30 s, 1 min, 2 min (adjustable)
RS-232 interface with optic insulator
in English, included
multi-function display
42 to 63 Hz
8 batteries (1.5 V) or 12 V / 300 mA adapter
ABS plastic
235 x 116 x 54 mm
730 g
CAT III/600 V; DIN VDE 0411/ EN 61010 / IEC 61010; class II; IP 30; degree 2
Contents
PCE-PA6000 power meter, control cable, software, RS-232
interface and user’s manual
Measurement interval
Data transfer / Interface
Software / USB cable
Display
Frequency range
Power
Enclosure
Dimensions
Weight
Approvals
Contents
PCE-360 3-phase power analyser, 4 test leads with alligator clips, 4 current clamp transducers, 4 safe measurement cables, 8 batteries,
adaptor, carrying case, RS-232 cable for PC, software and user’s manual (For U.K. customers: incl. U.K. AC Mains Power Adaptor)
Model No.
PCE-PA6000
Model No.
PCE-360
PCE-PA-ADP
power adaptor
(optional)
Description
Power meter
Optional accessories
PCE-PA-ADP Power adaptor
NET-300
Adaptor
RS232-USB
RS-232 to USB adaptor
CAL-2535
ISO cetificate
60
Current measurement
Range:
Description
3-Phases power analyser
Optional accessories
RS232-USB
RS-232 to USB adaptor
CAL-PCE-360
ISO certificate
Electricity Meters
PCE-830
Power and harmonics analyser with 3 phases as well as an energy meter (real time) and harmonics analyser with memory, PC port and software
The PCE-830 energy and harmonics analyser is used to measure one of three phases of electrical magnitudes for alternative current. Also, to detect the magnitudes of “normal” measurements like voltage, current,
frequency, power, energy and also indicates, according to standard EN50160, harmonic, inter-harmonic and asymmetrical values. Interference in power such as interruptions, shortages, temporary surges (from
16 µs) are detected with their corresponding values. The LCD, that has good contrast, a points matrix and backlight, shows up to 35 simultaneous parameters. It can incorporate up to 3 current clamps at the
same time. In data registration mode, it can save up to 17,470 readings (3 phases / 4 conductors), or more simple, up to 52,400 readings (1 phase / 2 conductors), divided between 85 inspections. All of this
makes the PCE-830 energy and harmonics analyser ideal for measurements over extended periods of time. The readings obtained can be transferred to a computer and be analysed with the corresponding software.
Included with the analyzer are all the things required to measure and analyse the readings, including the software and data cable. Although the analyzer comes calibrated at the factory, and optional laboratory
calibration certificate which meets ISO standards, can be ordered (with the first order for annual recalibrations).
• Analysis of power networks of 3 phases/4 conductors, 3 phases/3 conductors,
1 phase/2 conductors or 1 phase/3 conductors
• Measurement of active energy (W, KW, MW, GW)
• Potency factor (PF), phase angle (Φ)
• Measurement of current of 0.1 mA to 3000 A, permitting,
for example, an analysis of the needs of reserve energy in a factory
• The conditions CT (1 to 600) and PT (1 to 3000) programmable
• Average power (AD en W, KW, MW)
• Indication of wave forms, performance parameters
and harmonic distortion
• Maximum potency (MD en W, KW, MW) with programmable time periods
• Indication on the display up to a 50 form of harmonic wave
• Analysis of absolute distortion (%THD-F)
• Detects up to 28 transistors (time and cycles) with a programmable threshold (%)
• Factor of 3 phases of energy or asymmetrical current (d0%, d2%)
• Programmable time intervals and integrated calendar to record data
Technical specifications
Watts AC
Range / accuracy
(50 or 60 Hz, PF 0,5 up to 1,0)
Current AC
Voltage AC
Range / accuracy
•
•
•
•
•
•
•
•
•
•
•
•
Measurement of Real Effective Value
(V 123 and I 123 )
Measurement of apparent and reactive energy (KVA, KVAR)
Measurement of energy and work (Wh, KWh, KVARh, PFh)
Large LCD that shows up to 35 parameters simultaneously
(3P4W [=3 phases/4 conductors])
Indication of superimposed current wave forms and voltage
512 KB of memory with programmable intervals for readings
(measurement intervals of 2 to 3000 seconds, 17,470 readings
using a system of 3 phases / 4 conductors)
Analysis of harmonic distortion up to 99 types of waves lengths
Indication of the wave form with maximum value (1024 readings/period)
Diagram of grafic equilibrium with parameters of a 3 phase system
Relation of 3 phases of energy or asymmetrical current (VUR)
USB port, optically insulated
ISO calibration certificate (optional)
Set 1:
Range: up to 100 A
Dia. electrial conductor: max. 30 mm
Set 1
(incl. PCE-6801)
5,0 to 999,9 W / ±1 %
1,000 to 9,999 kW / ±1 %
10,00 to 99,99 kW / ±1 %
100,0 to 999.9 kW / ±1 %
1000 to 9999 kW / ±1 %
0,040 to 1,000 A / ±0,5 %
0,40 to 10,00 A / ±0,5 %
4,0 to 100,0 A / ±0,5 %
Range / accuracy (measurement between phase and neutral) 20,0 to 500,0 V /±0,5 %
(measurement between two phases)
20,0 to 600,0 V / ±0,5 %
0,00 to 1,00 / ±0,04
-180,0° to +180,0° / ±1°
Power factor
Gap angle
General specifications
Maximum measurement of AC current and voltage
Measurement of peak value of AC current and voltage
Frequency range
Memory
Interface
Display
Power
Dimensions / Weight
Operating conditions
Approvals
Set 2:
Range: up to 1000 A
Dia. electrial conductor: max. 55 mm
Set 2
(incl. PCE-6802)
5,0 to 999,9 W / ±1 %
1,000 to 9,999 kW / ±1 %
10,00 to 99,99 kW / ±1 %
100,0 to 999.9 kW / ±1 %
1000 to 9999 kW / ±1 %
0,000 to 9,999 MW / ±1 %
0,400 to 10,000 A / ±0,5 %
4,00 to 100,00 A / ±0,5 %
40,0 to 1000,0 A / ±0,5 %
20,0 to 500,0 V /±0,5 %
20,0 to 600,0 V /±0,5 %
0,00 to 1,00 / ±0,04
-180,0° to +180,0° / ±1°
Set 3:
Range: up to 3000 A
Dia. electrial conductor: max. 170 mm
Set 3
(incl. PCE-3007)
5,0 to 999,9 W / ±1 %
1,000 to 9,999 kW / ±1 %
10,00 to 99,99 kW / ±1 %
100,0 to 999.9 kW / ±1 %
1000 to 9999 kW / ±1 %
0,0 to 300,0 A / ±1 %
300,0 to 999,9 A / ±1 %
1000 to 3000 A / ±1 %
20,0 to 500,0 V /±0,5 %
20,0 to 600,0 V /±0,5 %
0,000 to 1,000 / ±0,04
0 to 180,0° / ±1°
50 + 60 Hz / ±5 %
1,00 to 99,99 / ±5 %
45 to 65 Hz / ±0,1 Hz
512 kB (memory is not volatile) up to 52,420 readings carrying out a 1 phase/2 conductor measurement
USB (optically isolated)
grapfic LCD with backlight
8 AA batteries 1.5 V
257 x 155 x 57 mm / 1160 g
-10 to +50 °C / max. 85 % r.h.
IEC 61010, 600 V / CAT III
Contents
PCE-830 energy and harmonics analyser, 3 amp clamps (according to the model ordered), 4 insulated terminals, 4 safe test lines, 8 batteries, mains adaptor, case, USB cable, software and user’s manual
(For U.K. customers: incl. U.K. AC Mains Power Adaptor)
Model No.
PCE-830-1
PCE-830-2
PCE-830-3
Description
Energy analyser Set 1 (incl. PCE-6801)
Energy analyser Set 2 (incl. PCE-6802)
Energy analyser Set 3 (incl. PCE-3007)
Optional accessories
PCE-6801
Set of clamps 1 (for replacement or extension)
PCE-6802
Set of clamps 2 (for replacement or extension)
PCE-3007
Set of clamps 3 (for replacement or extension)
CAL-PCE-830
ISO certificate
61