Download PMB1008-Rev 1.indd - Allied Systems Company

21433 SW Oregon Street
Sherwood, Oregon 97140
USA
Tel (503) 625-2560 • Fax (503) 625-5132
PARTS
BULLETIN
DATE:
December 27, 2011
BULLETIN NO.
PAGE:
1 of 2
MODEL(S):
PMB1008-Rev 1
W3C Winches
ATTENTION: PARTS AND SERVICE MANAGERS
SUBJECT:
RECOMMENDED SERVICE INTERVALS FOR W3C WINCHES
Allied Systems Company is pleased to announce an additional tool to keep your customer’s winch serviced
and functioning properly. Following this recommended service schedule will help keep tractor winch downtime
to a minimum, optimize winch operation, and extend the life of your investment. See Table 1 on this page for
recommended service intervals, and Table 2 on the next page for recommended service kits.
Table 1. Recommended Winch Service Intervals
NOTE: Following the above service schedule protects your investment.
Contact the Allied Systems Company Parts or Service Department at 503-625-2560 if you have any questions.
Allied Systems Co. reserves the right to make changes to new equipment without incurring the obligation to make such changes to equipment previously manufactured.
Form 81-94
Printed in USA
BULLETIN NO: PMB1008-Rev 1
Date: December 27, 2011
PAGE:
2 of 2
SERVICEKITSFORW3CWINCHES
GearRatios
39:1
61:1
ServiceDescription
KitDescription
FilterChange
(First250,thenevery500Hours)
CleanDebrisFrom317757W(Strainer)
[ConsultParts/ServiceManual]
CompleteOilChange
(Every1000hours)
ͲN/AͲ
PFO
PFR
HighPTO
Input
KitPartNumber
N/A
ConsultTractorOperators/ServiceManualforApprovedOils
PumpAssembly
ALL
ALL
ALL
X
X
ALL
R15
X
MajorOverhaul
(Every10000Hours)
TractorCode
ALL
SealantforFramesandCovers
BrakeAssemblyKit
ClutchAssemblyKit
ClutchandBrakeOverhaul
(Every5000Hours)
LowPTO
Input
InputClutchShaftBearingKit
InputClutchShaftBearingKit
InputClutchShaftBearingKit
InputClutchShaftBearingKit
InputClutchShaftBearingKit
InputClutchShaftBearingKit
InputClutchShaftBearingKit
InputClutchShaftBearingKit
InputClutchShaftBearingKit
InputClutchShaftBearingKit
Clutch,Brake,andIntermediateShaftBearingandSealKit
RingandPinion,Drum,andFreespoolShaftBearingandSealKit
GearRatios
39:1
61:1
X
X
X
X
X
X
X
X
X
X
PFO
PFR
X
X
X
X
X
X
LowPTO
Input
X
X
X
X
X
X
X
HighPTO
Input
X
X
X
X
X
X
X
ALL
ALL
ALLExceptR15
313022W
2300576W
2303047W
2303531W
1314522W
2303531W
TractorCode
KitPartNumber
R15
R15
ALLExceptR15
ALLExceptR15
ALLExceptR15
ALLExceptR15
ALL
ALL
ALL
ALL
2313009
2313008
2313007
2313009
2313007
2313009
2313008
2313009
2313008
2313009
2313010
2313011
Table 2. Recommended Service Kits
Serial Number Codes
The nameplate with the serial number code is found on the left front corner of the winch case.
A serial number indicates the following information:
A
W3C
P
1
A
1556
R11
Vehicle Code
Manufactured By
See Service Manual for Vehicle Code
A = Allied Systems Compay
(no “A” = Hyster Company)
Winch Model
Sequence Number
W3C = Standard
Drive Type
Internal Options
P = Power Controlled
Gear Ratio Code
5 = 39/1 Crawler
6 = 61/1 Crawler
(PFO) Power Forward Only, With Freespool = A
(PFR) Power Forward & Reverse, With Freespool = B
Note:
In Addition to the serial number plate, the serial number
is stamped on the top left-hand side of the frame.
Allied Systems Co. reserves the right to make changes to new equipment without incurring the obligation to make such changes to equipment previously manufactured.
Form 81-94
Printed in USA