Download Service Manual

ET–28
BODY EXTERIOR - QUARTER PANEL WHEEL OPENING MOULDING LH
QUARTER PANEL WHEEL OPENING MOULDING LH
BODY EXTERIOR
AND ELECTRICAL
COMPONENTS
REAR WHEEL
OPENING
EXTENSION
NO. 1 RH
MOULDING
COVER NO.1
REAR WHEEL OPENING
EXTENSION PAD NO. 1
ET
QUARTER OUTER
SIDE MOLDING RH
REAR WHEEL OPENING
EXTENSION PAD NO. 1
OUTSIDE MOLDING RETAINER NO. 2 RH
MOUNTING
BRACKET
NO.1
MOUNTING
BRACKET
NO.2
REAR WHEEL OPENING
OUTSIDE MOLDING RETAINER
EXTENSION NO. 1 LH
NO. 3 LH
MOULDING COVER NO.1
REAR
WHEELOPENING
EXTENSION PAD
NO. 2
OUTSIDE MOLDING CLIP NO. 4
QUARTER OUTSIDE MOLDING LH
..... NON-REUSEABLE PART
REAR WHEEL OPENINGEXTENSION
PAD NO. 2
B141276J01
BODY EXTERIOR - QUARTER PANEL WHEEL OPENING MOULDING LH
ET–29
REMOVAL
1.
REMOVE MOLDING COVER NO. 1
(a) Disengage the 2 claws and remove the moulding cover No. 1.
2.
REMOVE REAR WHEEL OPENING EXTENSION NO. 1 LH
(a) Apply protective tape as shown in the illustration.
(b) Remove the rivet.
(1) Wrap tape around the drill bit leaving approximately 5 mm
from the tip of the drill bit, as shown in the illustration.
HINT:
The purpose of wrapping the tape around the drill bit is to
prevent the drill from drilling too deep.
(2) Apply and hold the drill to the rivet. Drill the rivet flange
area and remove the rivet.
(c) Heat the rear wheel opening extension No. 1 using a heat gun.
B137925
Protective Tape
B137922J01
(d)
Remove the screw, disengage the cllips, and remove the rear
wheel opening extension No. 1 LH.
ET
B137921
B137923
3.
REMOVE OUTSIDE MOULDING RETAINER NO. 3 LH
(a) Remove the 3 screws and the outside moulding retainer No. 3
LH.
4.
REMOVE REAR WHEEL OPENING EXTENSION PAD NO. 1
(a) Remove the rear wheel opening extension No. 1 from the rear
wheel opening extension No. 1 LH.
ET–30
BODY EXTERIOR - QUARTER PANEL WHEEL OPENING MOULDING LH
5.
REMOVE QUARTER OUTSIDE MOULDING LH
(a) Apply protective tape as shown in the illustration.
(b) Remove the 2 screws and the 3 clips.
(c) Heat the quarter outside moulding RH using a heat gun.
(d) Disengage the 5 clips and remove the quarter outside moulding
RH.
6.
REMOVE OUTSIDE MOULDING CLIP NO. 4
(a) If the outside moulding clip No. 4 remains on the vehicle side,
turn it to about 90° and remove it, as shown in the illustration.
7.
REMOVE MOUNTING BRACKET NO.1
(a) Remove the 2 screws and mounting bracket No. 1.
8.
REMOVE MOUNTING BRACKET NO. 2
(a) Remove the 2 screws and mounting bracket No. 2.
9.
REMOVE REAR WHEEL OPENING EXTENSION PAD NO. 2
(a) Remove the rear wheel opening extension pad No. 2 from the
quarter outside moulding.
Protective Tape
:Clip
B137909J01
B137911
No.1
No.2
ET
B137910J01
INSTALLATION
1.
CLEAN INSTALLATION SURFACE
(a) Heat the double sided tape on the body using a heat gun. Then
wipe off the tape using a rag or piece of cloth.
(b) Clean the surface with a solvent.
2.
CLEAN QUARTER OUTSIDE MOULDING AND REAR WHEEL
OPENING EXTENSION (WHEN REUSING)
(a) CLEAN DOUBLE SIDED TAPE INSTALLATION SURFACE
(1) Heat the double sided tape that remains on the quarter
outside moulding and the rear wheel opening extension
using a heat gun.
(2) While heating the tape with the heat gun, use a rag or
piece of cloth to wipe off the double sided tape remaining
on the quarter outside moulding and the rear wheel opening extension.
NOTICE:
• Remove as much of the double sided tape as possible. Any tape that remains may cause attachment failure when the quarter outside moulding
and the rear wheel opening extension are
installed.
BODY EXTERIOR - QUARTER PANEL WHEEL OPENING MOULDING LH
ET–31
•
(3)
Use a waste cloth to scrub off, because it may
cause damage and attachment failure if using a
driver.
Clean the surface with a solvent.
3.
INSTALL MOUNTING BRACKET NO.1
(a) Install the 2 screws and mounting bracket No. 1.
NOTICE:
Do not confuse mounting bracket No. 1 with mounting
bracket No. 2. The parts look alike.
4.
INSTALL MOUNTING BRACKET NO. 2
(a) Install the 2 screws and mounting bracket No. 2.
NOTICE:
Do not confuse mounting bracket No. 2 with mounting
bracket No. 1. The parts look alike.
5.
INSTALL OUTSIDE MOULDING CLIP NO. 4
(a) Install the outside moulding clip No. 4 to the quarter outside
moulding LH.
6.
INSTALL REAR WHEEL OPENING EXTENSION PAD NO. 1
(a) Install the front wheel opening extension pad No. 2 to the front
fender moulding LH using double sided tape.
7.
INSTALL QUARTER OUTSIDE MOULDING LH
(a) Using a heat gun, heat both the quarter outside moulding LH
and the surface of the body.
No.1
No.2
B137910J01
REAR WHEEL OPENING
EXTENSION PAD NO. 1
B147247J01
(b)
(c)
Protective Tape
:Clip
Attach the 5 claws and install the quarter outside moulding LH.
Connect the 2 screws and the 3 clips and attach it thoroughly.
NOTICE:
Be careful not to touch the adhesive surface with your fingers when removing the exfoliate paper from the double
sided tape.
B137909J01
8.
B137923
INSTALL OUTSIDE MOULDING RETAINER NO. 3 LH
(a) Install the outside moulding retainer No. 3 LH with the 3 screws.
ET
ET–32
BODY EXTERIOR - QUARTER PANEL WHEEL OPENING MOULDING LH
9.
INSTALL REAR WHEEL OPENING EXTENSION PAD NO. 2
(a) Install the rear wheel opening extension pad No. 2 to the rear
wheel opening extension No. 1 LH with double-sided tape.
10.
INSTALL REAR WHEEL OPENING EXTENSION NO. 1
(a) Using a heat gun, heat both the rear wheel opening extension
No. 1 LH and the surface of the body.
REAR WHEEL OPENING
EXTENSION PAD NO. 2
(b)
(c)
Connect the 2 claws and the screw, and firmly press the extension to the vehicle body.
NOTICE:
Be careful not to touch the adhesive surface with your fingers when removing the exfoliate paper from the double
sided tape.
Install the rivet.
(1) Put nose piece No. 2 on the riveter.
B137921
(2)
ET
Using the riveter, install a new rivet. Operate the riveter
while holding it perpendicular to the rivet hole.
B137922
11.
B137925
INSTALL MOULDING COVER NO.1
(a) Engage the 2 claws and install the moulding cover No. 1.