Download SERVICE MANUAL

ICD-BX800
SERVICE MANUAL
E Model
Ver. 1.0 2010.02
SPECIFICATIONS
IC recorder section
General
Capacity (User available capacity)
2 GB (approx. 1.79 MB =1,924,136,960 Byte)
A part of the memory capacity is used as a
management area.
Speaker
Approx. 28 mm (1 1/8 in.) dia.
Recording time
Maximum recording time*1*2
The maximum recording time of all the folders
is as follows.
SHQ mode
HQ mode
SP mode
22 hr. 15 min. 33 hr. 20 min. 89 hr.
LP mode
534 hr. 25 min.
(hr. : hours/min. : minutes)
*1 When you are going to record continuously
for a long time, you may have to replace the
batteries with new ones in the midst of recording.
*2
The maximum recording time varies if you
record messages in mixed recording mode.
Frequency range
• SHQ : 75 Hz - 20,000 Hz
• HQ : 75 Hz - 17,000 Hz
• SP : 75 Hz - 15,000 Hz
• LP : 80 Hz - 3,500 Hz
Input/Output
• Microphone jack (minijack, stereo)
– input for plug in power, minimum input
level 0.4 mV, 3 kilohms or lower impedance
microphone
• Headphone jack (minijack, stereo)
– output for 16 - 300 ohms headphones
Playback speed control (DPC)
+100% to –50%
Power output
300 mW
Power requirements
Two LR03 (size AAA) alkaline batteries
(supplied): 3.0 V DC
Two NH-AAA rechargeable batteries (not
supplied): 2.4 V DC
Mass (JEITA)*3
Approx. 71 g (2 1/2 oz) including LR03 (size
AAA) alkaline batteries
*3 Measured value by the standard of JEITA
(Japan Electronics and Information
Technology Industries Association)
Supplied accessories
IC Recorder (1)
LR03 (size AAA) alkaline batteries (2)
Stereo headphones*4 (1)
Carrying pouch*4 (1)
Stereo microphone with shirt-clip*4 (1)
Operating Instructions
*4 The stereo headphones, carrying pouch
and stereo microphone with shirt-clip are
supplied with some models in some regions
only.
Design and specifications are subject to
change without notice.
Operating temperature
5˚C - 35˚C (41˚F - 95˚F)
Dimensions (w/h/d) (not incl.
projecting parts and controls) (JEITA)*3
37 × 111 × 21.2 mm (1 1/2 × 4 3/8 × 27/32 in.)
MP3 bit rate and sampling frequency
for recording mode
• SHQ : 44.1 kHz, 192 kbps
• HQ : 44.1 kHz, 128 kbps
• SP : 44.1 kHz, 48 kbps
• LP : 11.025 kHz, 8 kbps
IC RECORDER
9-889-753-01
Sony Corporation
2010B0400-1
© 2010.02
Audio&Video Business Group
Published by Sony Techno Create Corporation
ICD-BX800
NOTES ON CHIP COMPONENT REPLACEMENT
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
FLEXIBLE CIRCUIT BOARD REPAIRING
• Keep the temperature of soldering iron around 270 °C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
2
TABLE OF CONTENTS
1.
DISASSEMBLY
1-1.
1-2.
1-3.
1-4.
1-5.
Disassembly Flow ...........................................................
Battery Case Lid .............................................................
Case (Front) Assy, Speaker (SP101) ...............................
Complete Main Board .....................................................
Liquid Crystal Display Panel (LCD101),Main Board....
3
3
4
5
5
2.
TEST MODE ............................................................
6
3.
DIAGRAMS
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
3-8.
Block Diagram ................................................................
Printed Wiring Board -Main Section (1/2)- ....................
Printed Wiring Board -Main Section (2/2)- ....................
Schematic Diagram -Main Section (1/5)- .......................
Schematic Diagram -Main Section (2/5)- .......................
Schematic Diagram -Main Section (3/5)- .......................
Schematic Diagram -Main Section (4/5)- .......................
Schematic Diagram -Main Section (5/5)- .......................
4.
EXPLODED VIEWS
11
13
14
15
16
17
18
19
4-1. Case (Front) Section ....................................................... 27
4-2. Case (Rear) Section ........................................................ 28
5.
ELECTRICAL PARTS LIST .............................. 29
Accessories are given in the last of the electrical parts list.
ICD-BX800
SECTION 1
DISASSEMBLY
•
This set can be disassembled in the order shown below.
1-1.
DISASSEMBLY FLOW
SET
1-2.
BATTERY CASE LID
(Page 3)
1-3.
CASE (FRONT) ASSY,
SPEAKER (SP101)
(Page 4)
1-4.
COMPLETE MAIN BOARD
(Page 5)
1-5.
LIQUID CRYSTAL DISPLAY PANEL (LCD101),
MAIN BOARD
(Page 5)
Note: Follow the disassembly procedure in the numerical order given.
1-2.
BATTERY CASE LID
3 battery case lid
1 claw
2 claw
3
ICD-BX800
1-3.
CASE (FRONT) ASSY, SPEAKER (SP101)
6 case (front) assy
5 two claws
1 tapping screw
4 two claws
3 two claws
2 two screws
7 two screws
9 bracket (speaker)
black
8 bracket (speaker)
red
qa speaker (SP101)
case (front) assy
0 Remove the two solders.
4
ICD-BX800
1-4.
COMPLETE MAIN BOARD
1 screw
3 COMPLETE MAIN board
2 Remove the two solders.
case (rear) assy
1-5.
LIQUID CRYSTAL DISPLAY PANEL (LCD101), MAIN BOARD
3 holder (LCD)
5 connection conductive board
6 liquid crystal display panel
(LCD101)
2 electret condenser microphone
(MIC101)
red
black
4 spacer (LCD)
7 MAIN board
1 Remove the two solders.
5
ICD-BX800
SECTION 2
TEST MODE
1. Outline of the TEST MODE
The TEST MODE is designed to help verify the set when servicing it.
The TEST MODE is only menu driven to select modes for servicing.
2. Entering and Canceling the TEST MODE
With the power on, turn on the [HOLD] switch while pressing the
[x] button and the [FOLDER/MENU] button at the same time.
5. Operation Display of respective menus
The operational and screen information about the respective menus
is described.
5-1. Initial Display in TEST MODE
LCD indications (destination information, memory capacity, CPU
FW version information, MIC sens and ALC) when TEST MODE
is entered:
mH
3. Canceling the TEST MODE
The TEST MODE can be cancelled by turning off the power (unplugging the dry battery.)
DPC
01
P 1.00.02
4. Flow Chart of TEST MODE
Select the desired item by using the [> +]/[– .] button, and
press the [N ENTER] button to set the selection.
Model information
START
TEST MODE
KEY
CHARGE
m
m
This display used to “5-4. Audio Loop”.
H
DPC
DPC
01
KEY
m
H
DPC
LCD
[>]
KEY COUNT
H
BEEP
[.]
m
H
DPC
DPC
COUNT
BEEP
SLEEP
m
AUDIO LOOP
H
m
H
DPC
DPC
SLEEP
RADIO
BATTERY LIFE
m
BATT AD,DCIN
H
RTC
DPC
BATLIFE
m
H
DPC
m
H
DPC
BATT DC
RTC
Turn off the power
(Remove the batteries)
END
TEST MODE
6
ALC
(DPC : ON)
(
: OFF)
L mH
LCD,LAMP
R1.00.02
CHARGE
m
CPU FW version information
MAIN MENU
H
Memory capacity
(01 : 1GB)
(02 : 2GB)
(04 : 4GB)
(00 : Access Error)
MIC sens
DPC
VOL.10
Volume
(VOL.00~30)
ICD-BX800
5-4. Audio Loop
“Audio loop” has the following four recording modes:
• Fs = 44.1 kHz, Stereo
• Fs = 44.1 kHz, Mono
• Fs = 22.05 kHz, Stereo
• Fs = 11.025 kHz, Mono
5-2. LCD, Lamp Test
“LCD, lamp test” has the following three modes:
1. LCD all displayed (including lamps all on)
2. LCD, lamp all off (green lamp on)
3. Check pattern (red lamp on)
First the all on mode is activated. Then the mode is switched from
one to another by pressing [> +] and [– .].
mH
In the loop mode, the VOR value is always acquired and indicated.
When the VOR value is larger than its set value, the red lamp goes
on.
DPC
mH
DPC
LC:D
AU:010
B ENTER
x
u
A B C D E
m H mL SHQSPLP
REC
,
88
RECDATE
REMAIN
YH
B ENTER
x
All on
Loop Mode
When the VOR value is large than its set value,
the red lamp goes on.
N-CUT
EASY-S
DPC
.
88 8%
MM
Fs=44.1kHz.Stereo
DS
1:8:8:8 :8:8 ::8:8
-.
mH
>+
44
All off
(Green LED on)
>+
DPC
ST
V0R 00 00
-.
>+
-.
>+
Fs=44.1kHz.Mono
-.
mH
>+
A
mH
C
44
u
E
SHQ LP
REC
55
RECDATE
H
V0R 00 00
EASY-S
-.
01 2
M
S
1234 56 78
>+
Fs=22.05kHz.Stereo
Check Pattarn
(Red LED on)
Lm
22
To exit from this test mode, get back to the menu screen by pressing the [x] button.
B ENTER
DPC
-.
DPC
:BEEP
x
>+
Fs=11.025kHz.Mono
Lm
mH
13
DPC
ST
V0R 00 00
5-3. BEEP Test
To enter the BEEP Test, press the [N ENTER] button.
mH
DPC
in
-.
11
DPC
in
i
V0R 00 00
:BEEP
Beep: Frequency 1.3kHz only
To exit from this test mode, get back to the menu screen by pressing the [x] button.
To exit from this test mode, get back to the menu screen by pressing the [x] button.
7
ICD-BX800
5-5. Batt AD, DCIN
The current AD value (hexadecimal) of BATT_AD is indicated
and whether DCIN is present or not is displayed. When DCIN is
present, BATT_AD is not read. (> displayed)
BATT_AD AD value
B ENTER
mH
FF
DPC
:8RTT :OC
mH
x
DPC
ON
5-7. Battery Life
This mode provides only the display mode designed to indicate the
previous measurement results.
Only this mode provides the measurement mode to record and play
back automatically until the low battery is reached and to write a
log at the end of operation.
• Display Mode
The mode of operation (record and playback), the recording mode,
and the date (year, month and day) and time of start and end of
operation are indicated on the display screen.
:8RTT :OC
mH
DPC
DCIN with/without information
:BATLIFE
To exit from this test mode, get back to the menu screen by pressing [x] button.
B ENTER
x
5-6. RTC Test
One second update interrupt is set for the RTC. When an interrupt
occurs, “OK” is displayed. If no interrupt occurs after an elapse of
three seconds, “NG” is displayed.
B ENTER
mH
REC
mH
mH
REC
mode
mH
DPC
REC
days
start
DTC
Y
DPC
PLAY
M
ST
D
080101
end
DTC
H
times
End
M
S
123456
OK
RTC
RTC “OK”
x
To exit from this test mode, get back to the menu screen by pressing the [x] button.
mH
DPC
NG
RTC “NG”
To exit from this test mode, get back to the menu screen by pressing [x] button.
8
ICD-BX800
5-8. Sleep Test
“Sleep mode” includes two different mode: “Sleep mode” and
“Deep sleep mode”. When each mode is selected, pressing the
[N ENTER] button causes a transfer to the assumed sleep mode.
mH
DPC
KEY
mH
B ENTER
DPC
SLEEP
B ENTER
x
Sleep Mode
A
mH
mH
DPC
B ENTER
N SLEEP
SHQ
01
u
DIVIDE
03
12:34
>+
DIVIDE
-.
Deep Sleep Mode
z
/
DISPLAY
MENU
mH
DPC
B ENTER
D SLEEP
MENU
To exit from this test mode, get back to the menu screen by pressing the [x] button.
To exit from each mode, be sure to remove the power. That is,
release the set from the test mode. Although operating the buttons and switches causes a transfer to the normal mode, there is no
guarantee for proper operation.
Operate all the controls.
ACCESS
5-9. Key Test (Reset Menu)
Initialization
complete
Note: Once this mode is completed, the contents recorded by the user will
be all cleared and initialized.
Before executing this mode, see confirmation as to clearing of the
contents and take care of executing the mode.
When all the buttons and switches have been operated, “ACCESS”
is displayed. Initialization (all items cleared in all folders, menu
initialized, and title number initialized) is performed. When all has
been completed, “OK” is displayed. If the initialization is failed,
you see “----” displayed and the orange lamp flashing on and off
fast. The buttons and switches may be turned on and off in any
order. These 13 controls should be operated. When each control
is operated. The WAKE UP factor is checked before displaying. If
there are any buttons yet to be pressed, they are in key accept state.
Initialization
failed
OK
NG
oK
--------
To exit from each mode, be sure to remove the power. That is,
release the set from test mode.
9
ICD-BX800
5-10. Key Count
This mode is mainly used for key duration test. Upon entry into
this mode, a 5-digit counter is displayed. The counter is increment
each time one of the buttons and switches is operated once. The
digits indicate “00000” to “99999”. “00000” is redisplayed after
“99999”.
mH
B ENTER
DPC
COUNT
00000
To exit from each mode, be sure to remove the power. That is,
release the set from the test mode.
10
ICD-BX800
SECTION 3
DIAGRAMS
3-1.
BLOCK DIAGRAM
MIC/HP AMP,
CODEC(ADC,DAC),
IC2001
J1002
HPL 22
HPR 21
i
SPEAKER AMP
IC1001
1 MPWR
MIC101
(MICROPHONE)
31 LIN1/IN132 RIN1/IN1+
LOUT/
27
LOP
4 IN-
30 LIN2/IN2+
29 RIN2/IN2-
SP_PWR
SDI1/P16/SP_PWR 19
SDTI
LRCK
BICK
I2C_SDA
I2C_SCL
MCKI
ADA_XRST
55
58
57
61
60
59
63
DOUT/PCM_DADT
LRCK/P12/PCM_LRCK
BCK/PCM_BCK
I2C_SDA
SCL/P28/I2C_SCL
MCLK/P13/PCM_MCLK
ADA_XRST
SDO0/P09/SPI0_MOSI 15
SDI0/P0A/SPI0_MISO 16
SCK0/P08/SPI0_CLK 14
TIOCA1/P18/SCPU_CS 23
18
20
25
17
P43/SI/RX/SPI0_MOSI
P44/SO/TX/SPI0_MISO
P45/SCK/SPI0_SCK
P42/INT1/PWC/SCPU_CS
SEG0–SEG33
I
SEG36–SEG41
COM0–COM3
MICHP_DPC_AD
X5521
4MHz
110 AN3/MICHP_AD
DAT0
DAT1
DAT2
DAT3
H3
H4
H5
J2
71
74
75
76
70 SDCLK/SCLK/SD_CLK
69 SDCMD/BS/SD_CMD
CLK W6
CMD W5
KEY MATRIX
S6002–6006,6011
S6012–6016
S6021
HOLD
ON
R
OFF
KEY_AD0
KEY_AD1
KEY_AD0_WAKE
KEY_AD1_WAKE
SDAT0/DATA0/SD_DATA0
SDAT1/DATA1/SD_DATA1
SDAT2/DATA2/SD_DATA2
SDAT3/DATA3/SD_DATA3
23 X1
X4542
32.768kHz
Signal path
LIQUID
CRYSTAL
DISPLAY
PANEL
: PB
: REC
D6051 (RED)
P30/LED_XGRN 14
1 VOUT
VDD_DDCOUT+3.3V
VDD_CPU+3.1V
VDD 2
VDD_DDCOUT+3.3V
VDD_RTC
VDD 2
VDD_MCPU+1.1V
(+1.1V)
RTC
BACK UP
REG.
IC3051
D3051
VDD
CPU+3.1V
REG
IC3620
VOLTAGE DETECT
IC8021
4 OUT
VDET/RTC_VDET 88
VDD 2
RTC INT SWITCH
Q6093
EXTINT4/P25/RTC_XINT 51
VDD_UNREG
VDD
MCPU+1.1V
REG
IC3680
VDD_MCPU+1.1V
VDD NAND+3.1V
VDD
NAND+3.1V
REG
IC3630
83 XOUT1
DC/DC CONVERTER
IC3600
82 XIN1
VDD
ANA+2.9V
REG
IC3640
86 XOUT32K
VDD_ANA+2.9V
87 XIN32K
TXD1/P2A/ADA_PWR 20
ADA_PWR
LX 2
10 VOUT
BAT 3
8 FB
9 MODE
EN 4
L3601
+
SWITCH
Q3024
PHI/P11/BATT_XEN/UPG_RESULT 12
ANO/BATT_AD 107
BATT_XEN
BATT_AD
VDD BATT SWITCH
Q3022 (2/2)
ICD-BX800
(OPERATION)
D6052 (GREEN)
RESET
IC3062
NTRST/JTAG_NRST 7
48 EXTINT1/P22/KEY_HOLD
X4543
12MHz
4 VOUT
RTCINT 89
49 EXTINT2/P23/KEY_WAKE
KEY_HOLD
LCD101
EXTINT0/P21/BATTAD_EN 47
108 AN1/KEY_AD0
109 AN1/KEY_AD1
KEY WAKEUP SWITCH
Q6092
VDD_UNREG
P17/SEG35/LED_XRED 33
RESET
IC3061
NRES/MCPU_XRST 11
SP101
(SPEAKER)
22 X0
19 /RST/SCPU_XRST
SERIAL DATA CONTROL
IC6501
5–44
11
13
14
10
9
17
7
1–4
SDTI
LRCK
BICK
CDTI/SDA
CCLK/SCL
MCKI
PDN
-
1 NSHUTDOWN
VDD 6
LCD CONTROL
IC5521
5–1,64–57,
55–35,32–27
m
(PLUG IN POWER)
9–6
J1001
+
OUT+ 5
OUT- 8
MEMORY CONTROL,SYSTEM CONTROL
IC4541
11
11
+1.4V DETECT
IC3021
Q3022
(1/2)
3 VOUT
VIN 4
-
+
DRY BATTERY
SIZE “AAA”
IEC DESIGNATION
LR03
2PCS,3V
ICD-BX800
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
Note:
• X : Parts extracted from the component side.
•
f : Internal component.
•
: Pattern from the side which enables seeing.
(The other layers’ patterns are not indicated.)
Parts on the pattern face side seen
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
• Indication of transistor.
C
Q
These are omitted.
B E
• Lead layouts
Lead layout of conventional IC
ICD-BX800
– MAIN Board –
For Schematic Diagrams.
For Printed Wiring Boards.
Caution:
Pattern face side:
(SIDE B)
Parts face side:
(SIDE A)
• Waveforms
surface
Note:
• All capacitors are in μF unless otherwise noted. (p: pF) 50
WV or less are not indicated except for electrolytics and
tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
•
f : Internal component.
• C : Panel designation.
1
IC4541 id (XOUT1)
0.6 Vp-p
12 MHz
• A : B+ Line.
• Power voltage is dc 3V and fed with regulated dc power
supply from battery terminal.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : REC
(
): PB
• Voltages are taken with VOM (Input impedance 10 M).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
E
: PB
a : REC
0.2 V/DIV, 0.1 Psec/DIV
2
IC4541 ij (XIN32K)
0.4 Vp-p
32.768 kHz
0.1 V/DIV, 20 Psec/DIV
CSP (Chip Size Package)
12
12
ICD-BX800
3-2.
PRINTED WIRING BOARD – MAIN Section (1/2) – •
14
13
12
: Uses unleaded solder.
11
10
9
8
7
6
5
4
3
2
1
A
X5521
MAIN BOARD (SIDE A)
C1021
4
7
>+
JL5521
JL7502
8
JL7567
R3033
3
4
1
6
Q3022
C3621
C6505
C3631
C6504
z DISPLAY/
MENU
R4591
R4590
R1023
C5524
R3061
C4570
1
2
3
4
C1001
IC5521
R6001
S6012
C4566
JL7569
R1036
J1002
R1039
i
JL7558
C6503
C3062
48
49
2 3
IC3061
64
1
R1037
C4565
2
8
RB6005
1 4
JL3213 JL7568
E
C2015
R6063
1
2
3
4
C6071
B
ENTER
PLAY/STOP
1
7
F
R6052
JL3007
D6052
D6051
1-880-852D6051
D6052
(OPERATION) (OPERATION)
(RED)
(GREEN)
LCD101
LIQUID CRYSTAL DISPLAY PANEL
ICD-BX800
D
MIC101
(MICROPHONE)
RED
C2014
S6005
R3034
2
BLK
R6064
R3027
1
C2005
17
16
R6051
JL6537
S6004
R1012
R5577
R6092
C6092
IC3630
C4554
2
32
33
Q6093
C
R1001
R3143
C4568
1
8
R1024
C3641
JL3006
R6522
3
2
R6071
C4567
C6502
C3021
R3032
4
1
R3026
4 1
JL3002
C3630
R3690
JL3212
R3028
Q3024
R6070
4 1
7
JL1002
X5521
R6003
3 2
R3025
1
4
IC3640
IC3021
R3022
2
3
C3061
R3602
3
2
R4620
R4599
m
JL1001
R6053
C3681
x
4
1
IC3620
3 2
R4687
C3620
R3169
8
R4689
DIVIDE
C3640
RB6001
JL3215
C3682
JL3211
RB6002
R3023
7
2
R4598
S6015
IC3680
IC8021
C4560
R4688
JL1007
S6002
C4557
JL3011
2 3
1
JL7570
1 4
JL1005
DRY BATTERY
SIZE”AAA”
IEC DESIGNATION
LR03
2PCS,3V
X4543
C4556
C4555
C3680
JL7571
z
REC
/PAUSE
R3005
C3683
7
RB4500
R3680
JL1006
BLK
S6006
RB6068
1
C8021
C1020
–.
JL3217
8
JL6545
JL6544
JL6543
JL6542
JL6541
JL6540
JL6539
JL6538
JL6536
JL6535
JL6534
JL6533
JL6532
JL6531
JL6530
JL6529
JL6528
JL6527
JL6526
JL6525
JL6524
JL6523
JL6522
JL6521
JL6520
JL6519
JL6518
JL6517
JL6516
JL6515
JL6514
JL6513
JL6512
JL6511
JL6510
JL6509
JL6508
JL6507
JL6506
JL6505
JL6504
JL6503
JL6502
JL6501
JL1008
J1001
1
2
R3016
8
S6003
B
R1014
R1042
IC1001
SP101
(SPEAKER)
RED
C1025
C1019
C8022
5
JL7503
R1044
C1022
JL3004
13
13
11
(11)
G
ICD-BX800
3-3.
PRINTED WIRING BOARD – MAIN Section (2/2) – •
1
2
3
: Uses unleaded solder.
4
5
6
7
8
9
10
11
12
13
14
A
S6021
> HOLD
ON T OFF
S6021
R1021
C3051
R3051
JL7507
C2003
R4559
C2012
C4543
S6016
R1035
C4547 C4553
C3053
R6504
R6506
C3600
31
1
30
C4564
S6013
2
8
RB6004
1
7
JL7564
S6014
+
24
1
JL7565 JL7561
JL7560
JL7563 JL7559
JL7562
S6014
C3064
Q6092
S6011
2
3
1
4
IC3062
R6011
S6013
S6011
A –B
–
VOL
G
ICD-BX800
R6501
R6502
120
R6061
S6016
ERASE
C3601
C4551
C1004
R1038
F
4
3
2
1
C4569
C4550
C5521
R4546
10
6
IC4541
C4549
C1003
C2006
E
IC3600
IC6501
R1005
R6066
C2004
1
5
C4545
R2019
R1008
C2007
L3601
C3603
C2011
60
R3601
9
8
R3603
8
R1007
C1010
C1210
32
1
25
R3600
IC2001
48
R4555
C3063
D
R1006
R6069
91
C4552
2
2 3
IC3051
61
90
R2020
17
16
R7562
24
25
1
C4563
C4562
7
C2002
C1015
C1014
C2010
C4561
C2009
1 4
R6022
RB4501
C
C4558
X4542
JL7504
R6503
JL7506
R6021
C6501 R6505
JL7505
D3051
R1013
B
MAIN BOARD (SIDE B)
14
14
1-880-852-
11
(11)
ICD-BX800
3-4.
SCHEMATIC DIAGRAM – MAIN Section (1/5) –
• See page 12 for waveforms. • See page 20 for IC Block Diagram. • See page 24 for IC Pin Function Description of IC4541.
(Page 16)
RB4501
C4554
X4542
RB4500
IC8021
R4590
C4556
C4555
X4543
R4599
R4598
C4562
C4557
(Page 18)
R4591
JL7507 JL7558
C8022
C4563
IC B/D
C4558
C4560
C4561
R4620
C4552
R4689
R4687
R4688
C8021
R6071
R4555
R6070
Q6092
C6071
JL7570
JL7506
JL7571
JL7503
JL7505
JL7504
IC4541
C4549
(Page 17)
R4546
C4569
C4553
R6092
C6092
C4567
C4568
C4566
C4570
C4551
(Page 17)
Q6093
C4545
C4550
C4547
R4559
(Page 19)
C4543
C4564
R7562
(Page 18)
C3062
R3061
C3061
C3064
C3063
(Page 17)
(Page 19)
IC B/D
ICD-BX800
JL7567
JL7568
JL7502
JL7569
JL7563
JL7564
JL7565
JL7561
JL7562
JL7559
JL7560
C4565
IC3061
IC3062
IC B/D
15
15
ICD-BX800
3-5.
SCHEMATIC DIAGRAM – MAIN Section (2/5) –
R6522
(Page 19)
R6506
R6505
R6504
R6503
C6501
C6504
C6505
R6502
C6502
R6501
C6503
(Page 15)
IC6501
ICD-BX800
16
16
ICD-BX800
3-6.
SCHEMATIC DIAGRAM – MAIN Section (3/5) –
• See page 20 for IC Block Diagram.
(Page 15)
JL6537
RB6001
RB6002
R6003
R6001
S6002
R6053
(Page 19)
R6052
S6003
S6011
S6004
S6005
S6006
R6011
C5524
(Page 15)
X5521
RB6005
RB6004
R6051
R5577
D6051
(Page 15)
D6052
S6012
S6013
JL5521
R6022
R6021
S6021
IC5521
C5521
ICD-BX800
17
17
JL6544
JL6545
JL6543
JL6541
JL6542
JL6539
ICD101
JL6540
JL6538
JL6536
JL6535
JL6533
JL6534
JL6531
JL6532
JL6529
JL6530
JL6527
JL6528
JL6525
JL6526
JL6523
JL6524
JL6521
JL6522
JL6520
JL6519
JL6517
JL6518
JL6515
JL6516
JL6513
JL6514
JL6511
JL6512
JL6510
JL6508
JL6509
JL6506
JL6507
JL6505
JL6503
JL6504
JL6501
JL6502
IC B/D
S6014
S6016
S6015
ICD-BX800
3-7.
SCHEMATIC DIAGRAM – MAIN Section (4/5) –
• See page 20 for IC Block Diagrams.
R2020
C2003
R1008
R2019
C2002
R1007
C1004
R1035
J1002
R1036
C1003
R1006
R1005
R1037
R1039
R1038
C1020
C2005
C1022
IC B/D
RB6068
C2009
(Page 19)
IC1001
C2010
JL1007
SP101
IC B/D
JL1008
C1019
R1042
R1012
J1001
C1021
R6069
R1013
R1014
IC2001
C1015
R1001
MIC101
C2011
R1021
R1023 C1025
C2012
R1044
R1024
JL1001
C1014
C1010
C1001
JL1002
(Page 15)
C2004
C2014
R6066
C1210
(Page 15)
C2007
C2015
R6063
C2006
R6064
R6061
(Page 19)
ICD-BX800
18
18
ICD-BX800
3-8.
SCHEMATIC DIAGRAM – MAIN Section (5/5) –
• See page 22 for IC Block Diagrams.
IC3600
IC B/D
IC B/D
IC3630
C3600
C3603
L3601
JL3011
R3600
R3601
JL3006
R3690
C3631
C3630
C3621
C3620
(Page 18)
C3601
(Page 16)
IC B/D
R3603
IC3620
R3602
JL3007
R3143
JL3002
R3022
(Page 18)
JL3211
R3025
R3023
JL3213
R3026
JL3004
IC B/D
R3169
Q3024
R3027
C3641
IC B/D
C3640
IC3640
(Page 17)
IC3021
R3028
C3021
R3033
R3034
C3683
JL3212
IC B/D
IC3680
Q3022
C3680
C3682 C3681
D3051
R3032
JL3215
R3680
R3016
R3005
(Page 15)
(Page 15)
IC B/D
C3051
R3051
IC3051
C3053
JL3217
ICD-BX800
19
19
ICD-BX800
• IC Block Diagrams
SEG5
SEG6
SEG7
SEG8
SEG9
SEG10
SEG11
SEG12
VCC
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
IC5521 MB89951APMC-G-115E1 (MAIN Board (3/5))
IC8021 PST8309UL (MAIN Board (1/5))
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
GND 1
VDD 2
SEG4 1
48 P00/SEG20
SEG3 2
RD
47 P01/SEG21
SEG2 3
–
4 OUT
+
LCD
CONTROLLER
/DRIVER
SEG1 4
45 P23/SEG23
SEG0 5
VREF
46 P02/SEG22
ROM
F2MC-8L
CPU
RAM
COM3 6
20 BIT
TIME BASE TIMER
44 P24/SEG24
43 P05/SEG25
COM2 7
INTERNAL DATA BUS
3 CD
41 P07/SEG27
COM0 9
N-CH
OPEN
DRAIN
I/O
PORT
P32/V1/LCD_V1 12
P31/LED_XBIAS 13
VSS 1
P30/LED_XGRN 14
VDD 2
P40/MCPU_PWR 15
40 P10/SEG28
EXTERNAL
INTERRUPTION
RESET
CIRCUIT
WATCH
DOG TIMER
P33/V2/LCD_V2 11
IC3061 PST8429UL (MAIN Board (1/5))
8BIT PULSE
COUNT TIMER
8BIT
PWM
TIMER
V3 10
NOISE
CLEAR
CLOCK
CONTROL
39 P11/SEG29
UART
N-CH
OPEN
DRAIN
I/O
PORT
8BIT
SERIAL
I/O
38 P12/SEG30
37 P13/SEG31
36 P14/SEG32
OSCILLATION
CIRCUIT
35 P15/SEG33
PORT2,PORT3
4 VOUT
RD
42 P06/SEG26
COM1 8
34 P16/SEG34
/BATT_XEN
33 P17/SEG35
/LED_XRED
PORT0,PORT1
P41/LED_XORG 16
–
+
VREF
25
26
27
28
29
30
31
32
P23/SEG39
P22/SEG38
P21/SEG37
P20/SEG36
MODA
24
P24/SEG40
P44/SO/TX/SPIO_MISO
23
P25/SEG41
RST/SCPU_XRST
22
P46/INT0/ INT_WAKE
21
P45/SCK/SPIO_SCK
20
VSS
19
X1
18
PORT4
X0
17
P43/SI/RX/SPIO_MOSI
3 CD
P42/INT1/PWC/SCPU_CS
CMOS I/O
PORT
IC3062 PST8209UL (MAIN Board (1/5))
VOUT 1
IC1001 MM3111AWLE (MAIN Board (4/5))
VIN 2
–
SHUTDOWN 1
+
8 OUT7 GND
6 VDD
VREF
IN+ 3
IN- 4
4 VSS
3 NC
ICD-BX800
BIAS
BIAS 2
20
20
5 OUT+
ICD-BX800
RIN4/IN4-
MUTET
HPL
HPR
HVDD
HVSS
MCKO
MCKI
IC2001 AK4645AEZ-L (MAIN Board (4/5))
24
23
22
21
20
19
18
17
PMHPL
PMHPR
PMAINR4
PMAINL4
16 TVDD
LIN4/IN4+ 25
15 DVDD
PMLO
ROUT/LON 26
LOUT/LOP 27
PMDAC
PMMIN
D/A
MIN/LIN3 28
14 BICK
DATT
BASS
SMUTE BOOST
ALC
STEREO
SEPARATION
HPF
PMAINR2
RIN2/IN2- 29
13 LRCK
AUDIO
I/F
PMAINL2
LIN2/IN2+ 30
MIC AMP
PMDAL OR PMADR
LIN1/IN1- 31
A/D
PMADL
OR PMMICL
HPF
WIND-NOISE
REDUCTION
12 SDTO
STEREO
SEPARATION
ALC
11 SDTC
RIN1/IN1+ 32
PMADR
OR PMMICR
PMMP
MIC
POWER
SUPPLY
PMAINR3
10 CDTI/SDA
CONTROL
REGISTER
1
2
3
4
5
6
7
8
MPWR
VCOM
AVSS
AVDD
VCOC/RIN3
I2C
PDN
CSN/CAD0
9 CCLK/SCL
21
ICD-BX800
IC3021 XC6120N142NR (MAIN Board (5/5))
4 VIN
NC 1
R1
3 VOUT
–
+
R2
VREF
VSS 2
IC3051 MM3271BURE (MAIN Board (5/5))
IC3620 MM3273BURE (MAIN Board (5/5))
4 VIN
3 VOUT
CE 1
BIAS
–
+
VREF
CURRENT
LIMIT
VSS 2
IC3600 XC9129D45CDR (MAIN Board (5/5))
6 AEN
7 AGND
8 FB
9 MODE
PHASE
COMPENSATION
ERROR AMP
F0 5
BAT 3
LX 2
PGND 1
22
PWM
COMPARATOR
10 VOUT
PWM/PFM
CONTROLLER,LOGIC
VREF WITH
SOFT START
EN 4
CURRENT SENSE,
LIMIT,PFM
EN.
THERMAL SHUTDOWN
RAMP WAVE
GENERATOR
OSC
MODE
BUFFER
DRIVER
ICD-BX800
IC3630 XC6213B312NR (MAIN Board (5/5))
IC3640 XC6213B292NR (MAIN Board (5/5))
4 VDD
CE 1
ON/OFF
CONTROL
3 VOUT
CURRENT
LIMIT
+
–
VOLTAGE
REFERENCE
GND 2
IC3680 MM3359A11URE (MAIN Board (5/5))
4 VDD
3 VOUT
CE 1
BIAS
–
+
VREF
CURRENT
LIMIT
GND 2
23
ICD-BX800
• IC Pin Function Description
MAIN BOARD (1/5) IC4541 LC823410-10S2-H (MEMORY CONTROL, SYSTEM CONTROL)
Pin No.
1 to 4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41 to 46
47
48
49
50
51
52
53
54
24
Pin Name
TEST3 to 6
TCK/JTAG TCK
RTCK/JTAG RTCK
NTRST/JTAG NTRST
TDI/JTAG TDI
TMS/JTAG TMS
TDO/JTAG TDO
NRES/MCPU XRST
PHI/P11/BATT XEN/
UPG RESULT
EXTFIQ/P2F/
VBUS XDET
SCK0/P08/SPI0 CLK
SDO0/P09/
SPI0 MOSI
SDI0/P0A/SPI0 MISO
SCK1/P14/
CHG EN CLK
SDO1/P15/GPIO P15
SDI1/P16/SP PWR
TXD1/P2A/ADA PWR
RXD1/P2B/
RTC XSTBY
TIOCA0/P19/
CHGADC XCS
TIOCA1/P18/
SCPU CS
VDD1
VDD2
VSS
TXD0/UART TXD
RXD0/UART RXD
XFWE/NAND XWE
XFRE/NAND XRE
XALE/NAND XALE
XCLE/NAND XCLE
XFCE1/NAND XCE1
XFCE0/NAND XCE0
XFWP/NAND XWP
XFBSY/NAND XRB
FD0/NAND D0
FD1/NAND D1
VDD2
VSS
FD2/NAND D2 to
FD7/NAND D7
EXTINT0/P21/
BATTAD EN
EXTINT1/P22/
KEY HOLD
EXTINT2/P23/
KEY WAKE
EXTINT3/P24/
DCIN XDET
EXTINT4/P25/
RTC XINT
VDD1
VDD2
VSS
I/O
I
I
O
I
I
I
O
I
Description
Test pin Operation: “L” input
JTAG test clock signal input Not used. (Open)
JTAG test returned clock signal output Not used. (Open)
JTAG test reset signal input
JTAG test data signal input Not used. (Open)
JTAG test mode select signal input Not used. (Open)
JTAG test data signal output Not used. (Open)
Reset signal input
I/O
BATT XEN signal output
I/O
VBUS detect signal input
I/O
Serial interface clock signal output
I/O
Serial interface data signal output
I/O
Serial interface data signal input
I/O
Charge enable signal input/Serial clock signal output
I/O
I/O
I/O
VBUS power supply control signal output Not used. (Open)
Speaker power supply control signal output
Adapter power supply control signal output
I/O
Remote control power supply backup control signal output
I/O
Charge ADC cs terminal
Not used. (Open)
I/O
SCPU SPI CS terminal
—
—
—
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
I/O
I/O
—
—
Digital power supply pin (+1.1V)
Digital power supply pin (+3.1V)
Digital ground pin
UART transmission data input/output Not used. (Open)
UART receive data input/output Not used. (Open)
NAND FLASH write enable signal input/output Not used. (Open)
NAND FLASH read enable signal input/output Not used. (Open)
NAND FLASH address latch enable signal input/output Not used. (Open)
NAND FLASH command latch enable signal input/output Not used. (Open)
NAND FLASH chip enable signal input/output Not used. (Open)
NAND FLASH chip enable signal input/output Not used. (Open)
NAND FLASH write protect signal input/output Not used. (Open)
NAND FLASH busy signal input Not used. (Connect to ground.)
NAND FLASH data signal input/output Not used. (Open)
NAND FLASH data signal input/output Not used. (Open)
Digital power supply pin (+3.1V)
Digital ground pin
I/O
NAND FLASH data signal input/output
I/O
NAND REG power supply control signal output
I/O
Hold switch signal input
I/O
Key wake up signal input
I/O
DCIN detect signal input
I/O
RTC interruption signal input
—
—
—
Digital power supply pin (+1.1V)
Digital power supply pin (+3.1V)
Ground pin
Not used. (Open)
L: Active
H: Active
Not used. (Open)
ICD-BX800
Pin No.
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92, 93
94
95
96, 97
98 to 100
101
102
103
104
105
106
107
108
109
110
111
112
Pin Name
DOUT/PCM DADT
DIN/PCM ADDT
BCK/PCM BCK
LRCK/P12/
PCM LRCK
MCLK/P13/
PCM MCLK
SCL/P28/I2C SCL
I2C SDA
BOOT XMS
ADA XRST
TEST1
TEST2
VDD1
SDWP/SD WP
SDCD/INS/SD CD
SDCMD/BS/SD CMD
SDCLK/SCLK/
SD CLK
SDAT0/DATA0/
SD DATA0
VSS
VDD3
SDAT1/DATA1/
SD DATA1
SDAT2/DATA2/
SD DATA2
SDAT3/DATA3/
SD DATA3
AVDDPLL1
AVSSPLL1
VCNT1
VDDXT
VSSXT
XIN1
XOUT1
VDDRTC
VSSRTC
XOUT32K
XIN32K
VDET/RTC VDET
RTCINT
BACKUPB
AVDDPHY1
AVSSPHY1
RREF
AVSSPHY2
AVDDPHY2
AVSSPHY2
AVDDPHY2
DP
DM
AVSSPHY2
AVDDPHY2
AVDDADC
AN0/BATT AD
AN1/KEY AD0
AN2/KEY AD1
AN3/MICHP AD
AVSSADC
VSS
I/O
O
I
I/O
PCM serial data signal output
PCM serial data signal input
PCM bit clock signal input/output
Description
I/O
PCM LR serial clock signal input/output
O
PCM master serial clock signal output
O
O
I
I
I
I
—
I
I
O
I2C serial clock signal output
I2C serial data signal output
Boot mode select signal input
Adapter reset signal input
Test pin Operation: “L” input
Test pin Operation: “L” input
Digital power supply pin (+1.1V)
SD card write protect signal input Fixed at “L”.
SD card detect/MSINS signal input Fixed at “L”.
SD card command signal output
O
SD card serial clock signal output
I/O
SD card serial data signal input/output
—
—
Digital ground pin
Digital power supply pin (+3.1V)
I/O
SD card serial data signal input/output
I/O
SD card serial data signal input/output
I/O
SD card serial data signal input/output
—
—
O
—
—
I
O
—
—
O
I
I
O
I
—
—
I/O
—
—
—
—
I/O
I/O
—
—
—
I
I
I
I
—
—
Analog power supply pin for PLL1 (+1.1V)
Analog ground pin for PLL1
VCO control signal output for PLL1
Power supply pin for system (+1.1V)
Ground pin for system
Oscillation amplifier input for system/USB PHY (12MHz)
Oscillation amplifier output for system/USB PHY (12MHz)
Power supply pin for RTC
Ground pin for RTC
32.768kHz oscillation amplifier output for RTC
32.768kHz oscillation amplifier input for RTC
Remote control voltage detect signal input
RTC interruption signal output
RTC operation mode signal input
Power supply pin for USB PHY (+1.1V)
Analog ground pin for USB PHY
Reference resistance pin for USB PHY
Analog ground pin for USB PHY
Analog power supply pin for USB PHY (+3.1V)
Analog ground pin for USB PHY
Analog power supply pin for USB PHY (+3.1V)
USB serial data (+) signal input/output Not used. (Open)
USB serial data (–) signal input/output Not used. (Open)
Analog ground pin for USB PHY
Analog power supply pin for USB PHY (+3.1V)
Analog power supply pin for A/D converter (+3.1V)
A/D converter analog signal input Battery detect signal input
A/D converter analog signal input Key detect signal input
A/D converter analog signal input Key detect signal input
A/D converter analog signal input MIC/HP detect signal input
Analog ground pin for A/D converter
Digital ground pin
25
ICD-BX800
Pin No.
113
114
115
116
117
118
119
120
26
Pin Name
XIN2/NC
XOUT2/NC
VDD1
AVDDPLL2
AVSSPLL2
VCNT2
VDD2
VSS
I/O
I
O
—
—
—
O
—
—
Description
16.9344MHz oscillation signal input for audio Not used. (Open)
16.9344MHz oscillation signal output for audio Not used. (Open)
Digital power supply pin (+1.1V)
Analog power supply pin for PLL2 (+3.1V)
Analog ground pin for PLL2
VCO control signal for PLL2
Digital power supply pin (+3.1V)
Digital ground pin
ICD-BX800
SECTION 4
EXPLODED VIEWS
Note:
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• Items marked “*” are not stocked since
they are seldom required for routine service. Some delay should be anticipated
when ordering these items.
4-1.
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Color Indication of Appearance Parts Example:
KNOB, BALANCE (WHITE) . . . (RED)


Parts Color Cabinet’s Color
CASE (FRONT) SECTION
1
not supplied
SP101
2
2
3
case (rear) section
5
4
Ref. No.
1
2
3
Part No.
Description
A-1751-531-A
4-108-902-01
3-254-003-01
CASE (FRONT) ASSY
BRACKET (SPEAKER)
SCREW
Remark
Ref. No.
4
5
SP101
Part No.
Description
3-254-083-01
3-078-890-31
1-858-034-13
SCREW
SCREW, TAPPING
SPEAKER (2.8cm)
Remark
27
ICD-BX800
4-2.
CASE (REAR) SECTION
not supplied
57
not supplied
LCD101
51
58
not supplied
not supplied
not supplied
MIC101
56
not supplied
52
53
54
not supplied
55
Ref. No.
51
52
53
54
55
28
Part No.
Description
A-1751-539-A
4-121-462-02
4-121-460-02
4-121-461-01
4-121-452-12
CASE (REAR) ASSY
TERMINAL (–), BATTERY
TERMINAL (+,–), BATTERY
TERMINAL (+), BATTERY
LID, BATTERY CASE
Remark
Ref. No.
56
57
58
LCD101
MIC101
Part No.
Description
Remark
3-254-083-01
A-1751-532-A
4-109-994-01
1-811-039-11
1-542-786-11
SCREW
MAIN BOARD, COMPLETE
CUSHION (MICROPHONE)
DISPLAY PANEL, LIQUID CRYSTAL
MICROPHONE ELECTRET CONDENSER (MIC)
ICD-BX800
SECTION 5
ELECTRICAL PARTS LIST
Note:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the components used on the set.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• Items marked “*” are not stocked since
they are seldom required for routine service. Some delay should be anticipated
when ordering these items.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
Ref. No.
• CAPACITORS
uF: μF
• COILS
uH: μH
• SEMICONDUCTORS
In each case, u: μ, for example:
uA. . : μA. . , uPA. . , μPA. . ,
uPB. . : μPB. . , uPC. . , μPC. . ,
uPD. . : μPD. .
Part No.
Description
A-1751-532-A
MAIN BOARD, COMPLETE
*********************
Remark
4-109-994-01
CUSHION (MICROPHONE)
Ref. No.
MAIN
When indicating parts by reference number, please include the board name.
Part No.
Description
C3641
C3680
C3681
C3682
C3683
1-165-908-11
1-125-777-11
1-165-908-11
1-112-746-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.1uF
1uF
4.7uF
0.1uF
10%
10%
10%
10%
10%
10V
10V
10V
6.3V
10V
Remark
C4543
C4545
C4547
C4549
C4550
1-125-777-11
1-125-777-11
1-125-777-11
1-125-777-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
10V
10V
10V
10V
10V
C4551
C4552
C4553
C4554
C4555
1-125-777-11
1-125-777-11
1-125-777-11
1-164-858-11
1-164-858-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
22PF
22PF
10%
10%
10%
5%
5%
10V
10V
10V
50V
50V
C4556
C4557
C4558
C4560
C4561
1-164-848-11
1-164-848-11
1-125-777-11
1-125-777-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
8PF
8PF
0.1uF
0.1uF
0.1uF
0.5PF
0.5PF
10%
10%
10%
50V
50V
10V
10V
10V
C4562
C4563
C4564
C4565
C4566
1-125-777-11
1-125-777-11
1-125-777-11
1-125-777-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
10V
10V
10V
10V
10V
C4567
C4568
C4569
C4570
C5521
1-125-777-11
1-125-777-11
1-100-249-11
1-100-249-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.01uF
0.01uF
0.1uF
10%
10%
10%
10%
10%
10V
10V
16V
16V
10V
C5524
C6071
C6092
C6501
C6502
1-164-937-11
1-100-252-11
1-164-937-11
1-125-777-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.1uF
0.001uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
50V
6.3V
50V
10V
10V
C6503
C6504
C6505
C8021
C8022
1-165-908-11
1-125-777-11
1-165-908-11
1-125-777-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.1uF
1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
10V
10V
10V
10V
10V
< CAPACITOR >
C1001
C1003
C1004
C1010
C1014
1-164-937-11
1-128-964-91
1-128-964-91
1-125-777-11
1-165-908-11
CERAMIC CHIP
TANTAL. CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
100uF
100uF
0.1uF
1uF
10%
20%
20%
10%
10%
50V
6.3V
6.3V
10V
10V
C1015
C1019
C1020
C1021
C1022
1-165-908-11
1-107-819-11
1-165-908-11
1-164-935-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.022uF
1uF
470PF
0.1uF
10%
10%
10%
10%
10%
10V
16V
10V
50V
10V
C1025
C1210
C2002
C2003
C2004
1-165-884-11
1-164-937-11
1-127-715-11
1-127-715-11
1-165-884-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2.2uF
0.001uF
0.22uF
0.22uF
2.2uF
10%
10%
10%
10%
10%
6.3V
50V
16V
16V
6.3V
C2005
C2006
C2007
C2009
C2010
1-165-908-11
1-125-777-11
1-125-777-11
1-165-908-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.1uF
0.1uF
1uF
0.1uF
10%
10%
10%
10%
10%
10V
10V
10V
10V
10V
C2011
C2012
C2014
C2015
C3015
1-125-777-11
1-125-777-11
1-119-923-11
1-119-923-11
1-126-923-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.1uF
0.1uF
0.047uF
0.047uF
220uF
10%
10%
10%
10%
20%
10V
10V
10V
10V
10V
C3021
C3051
C3053
C3061
C3062
1-125-777-11
1-128-964-91
1-125-777-11
1-164-939-11
1-125-777-11
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
100uF
0.1uF
0.0022uF
0.1uF
10%
20%
10%
10%
10%
10V
6.3V
10V
50V
10V
C3063
C3064
C3600
C3601
C3603
1-164-937-11
1-125-777-11
1-165-989-11
1-165-989-11
1-164-850-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.1uF
10uF
10uF
10PF
10%
10%
10%
10%
0.5PF
50V
10V
6.3V
6.3V
50V
C3620
C3621
C3630
C3631
C3640
1-125-777-11
1-165-908-11
1-125-777-11
1-165-908-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
1uF
0.1uF
1uF
0.1uF
10%
10%
10%
10%
10%
10V
10V
10V
10V
10V
< DIODE >
D3051
D6051
D6052
8-719-069-28
6-502-193-01
6-502-197-01
DIODE 1SS400FJTE61
LED SML-D12V8WT86SN (OPERATION (RED))
LED SML-D12M8WT86SM (OPERATION
(GREEN))
29
ICD-BX800
MAIN
Ref. No.
Part No.
Description
Remark
Part No.
Description
R3026
R3027
R3028
R3032
R3033
1-218-965-11
1-218-989-11
1-218-989-11
1-218-989-11
1-208-935-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1M
1M
1M
100K
5%
5%
5%
5%
0.5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3034
R3051
R3061
R3143
R3169
1-208-935-11
1-218-941-81
1-218-965-11
1-218-990-81
1-218-989-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
100K
100
10K
0
1M
0.5%
5%
5%
1/16W
1/16W
1/16W
5%
1/16W
R3600
R3601
R3602
R3603
R3680
1-218-985-11
1-218-985-11
1-218-990-81
1-208-939-11
1-218-990-81
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
SHORT CHIP
470K
470K
0
150K
0
5%
5%
1/16W
1/16W
0.5%
1/16W
R3690
R4546
R4555
R4559
R4590
1-218-989-11
1-218-953-11
1-208-883-81
1-208-663-11
1-243-975-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1M
1K
680
150
4.7M
5%
5%
0.5%
0.5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R4591
R4598
R4599
R4620
R4687
1-218-981-91
1-218-989-11
1-218-945-11
1-208-663-11
1-218-949-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220K
1M
220
150
470
5%
5%
5%
0.5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R4688
R4689
R5577
R6001
R6003
1-218-945-11
1-218-945-11
1-218-990-81
1-218-965-11
1-218-965-11
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
220
220
0
10K
10K
5%
5%
1/16W
1/16W
5%
5%
1/16W
1/16W
R6011
R6021
R6022
R6051
R6052
1-218-965-11
1-218-985-11
1-218-953-11
1-218-957-11
1-218-949-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
470K
1K
2.2K
470
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
R6053
R6061
R6063
R6064
R6066
1-218-989-11
1-218-981-91
1-218-981-91
1-218-985-11
1-218-989-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1M
220K
220K
470K
1M
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
5%
5%
1/16W
1/16W
R6069
R6070
R6071
R6092
R6501
1-218-929-11
1-218-989-11
1-243-975-11
1-218-965-11
1-218-937-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10
1M
4.7M
10K
47
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R6502
R6503
R6504
R6505
R6506
1-218-937-11
1-218-937-11
1-218-937-11
1-218-937-11
1-218-937-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47
47
47
47
47
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R6522
R7562
1-218-990-81
1-218-990-81
SHORT CHIP
SHORT CHIP
0
0
< IC >
IC1001
IC2001
IC3021
IC3051
IC3061
6-707-089-01
(Not supplied)
(Not supplied)
(Not supplied)
6-713-333-01
IC
IC
IC
IC
IC
MM3111AWLE
AK4645AEZ-L
XC6120N142NR
MM3271BURE
PST8429UL
IC3062
IC3600
IC3620
IC3630
IC3640
6-713-360-01
(Not supplied)
6-713-367-01
6-708-467-01
6-708-986-01
IC
IC
IC
IC
IC
PST8209UL
XC9129D45CDR
MM3273BURE
XC6213B312NR
XC6213B292NR
IC3680
IC4541
IC5521
IC6501
IC8021
(Not supplied)
(Not supplied)
(Not supplied)
(Not supplied)
(Not supplied)
IC
IC
IC
IC
IC
MM3359A11URE
LC823410-10S2-H
MB89951APMC-G-115E1
THGBM1G4D1EBAI7
PST8309UL
< JACK >
J1001
J1002
(Not supplied)
(Not supplied)
JACK (m (PLUG IN POWER))
JACK (i)
< COIL >
L3601
(Not supplied)
INDUCTOR
4.7uH
Ref. No.
Remark
< LIQUID CRYSTAL DISPLAY >
LCD101
1-811-039-11
DISPLAY PANEL, LIQUID CRYSTAL
< TRANSISTOR >
Q3022
Q3024
Q6092
Q6093
6-551-871-01
6-552-217-01
6-550-271-01
6-550-243-01
FET UP0497AG08S0
FET RTM001P02T2L
TRANSISTOR DTA114YMFS6T2L
TRANSISTOR DTC144TMFS6T2L
< RESISTOR >
R1001
R1005
R1006
R1007
R1008
1-218-957-11
1-218-957-11
1-218-957-11
1-220-803-81
1-220-803-81
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
2.2K
2.2K
4.7
4.7
R1012
R1013
R1014
R1021
R1023
1-218-990-81
1-218-990-81
1-218-990-81
1-218-961-11
1-218-961-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
0
0
0
4.7K
4.7K
R1024
R1035
R1036
R1037
R1038
1-218-949-11
1-218-990-81
1-218-990-81
1-216-864-11
1-218-957-11
METAL CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
470
0
0
0
2.2K
5%
1/16W
5%
1/16W
R1039
R1042
R1044
R2019
R2020
1-218-957-11
1-218-969-11
1-218-977-11
1-218-929-11
1-218-929-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
22K
100K
10
10
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3005
R3016
R3022
R3023
R3025
1-218-965-11
1-218-965-11
1-218-975-11
1-218-981-91
1-218-990-81
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
10K
10K
68K
220K
0
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
30
5%
5%
5%
5%
5%
< NETWORK RESISTOR >
RB4500
RB4501
RB6001
RB6002
RB6004
1-234-382-21
1-234-378-21
1-234-375-21
1-234-376-11
1-234-375-21
RES, NETWORK 220KX4 (1005)
RES, NETWORK 10KX4 (1005)
RES, NETWORK 1KX4 (1005)
RES, NETWORK 2.2KX4 (1005)
RES, NETWORK 1KX4 (1005)
RB6005
1-234-376-11
RES, NETWORK 2.2KX4 (1005)
ICD-BX800
MAIN
Ref. No.
RB6068
Part No.
Description
1-234-382-21
RES, NETWORK 220KX4 (1005)
Remark
< SWITCH >
S6002
S6003
S6004
S6005
S6006
1-786-914-31
1-786-914-31
1-786-914-31
1-786-914-31
1-786-914-31
SWITCH, TACTILE (x)
SWITCH, TACTILE (– .)
SWITCH, TACTILE (> +)
SWITCH, TACTILE (N PLAY/STOP•ENTER)
SWITCH, TACTILE (z REC/PAUSE)
S6011
S6012
S6013
S6014
S6015
1-798-119-11
1-786-914-31
1-798-119-11
1-798-119-11
1-786-914-31
SWITCH, TACTILE ( A-B)
SWITCH, TACTILE (FOLDER/MENU)
SWITCH, TACTILE (VOL –)
SWITCH, TACTILE (VOL +)
SWITCH, TACTILE (DIVIDE)
S6016
S6021
1-798-119-11
1-572-922-11
SWITCH, TACTILE (ERASE)
SWITCH, SLIDE (HOLD)
< VIBRATOR >
X4542
1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz)
X4543
1-814-216-11 VIBRATOR, CRYSTAL (12MHz)
X5521
1-781-646-21 VIBRATOR, CERAMIC (4MHz)
*************************************************************
MISCELLANEOUS
**************
MIC101 1-542-786-11 MICROPHONE ELECTRET CONDENSER (MIC)
SP101
1-858-034-13 SPEAKER (2.8cm)
*************************************************************
ACCESSORIES
************
1-542-783-11
2-059-703-02
4-167-956-11
4-167-956-41
4-167-957-71
HEADPHONE (MDR-E706I) (E)
POUCH, CARRYING (E)
MANUAL, INSTRUCTION (ENGLISH)
MANUAL, INSTRUCTION (SPANISH)
MANUAL, INSTRUCTION (ARABIC) (E)
4-167-957-91
4-167-958-11
MANUAL, INSTRUCTION (PERSIAN) (E)
MANUAL, INSTRUCTION
(TRADITIONAL CHINESE) (E)
4-167-958-21 MANUAL, INSTRUCTION
(SIMPLIFIED CHINESE) (E)
4-167-958-31 MANUAL, INSTRUCTION (KOREAN) (E)
*************************************************************
31
ICD-BX800
REVISION HISTORY
Checking the version allows you to jump to the revised page.
Also, clicking the version at the top of the revised page allows you to jump to the next revised page.
Ver.
Date
1.0
2010.02
Description of Revision
New